* [PATCH v5 0/4] ARM: sunxi: Allwinner H3 support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij
Cc: Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, Jens Kuske, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
Hi everyone,
This is v5 of my patch series introducing basic kernel support for Allwinner's
H3 SoC. It mainly adds basic clocks, resets and pinctrl. It also adds
interrupts, timers, watchdog, RTC, dmaengine, MMC and UARTs, which are mostly
compatible to those in earlier SoCs like A23 and A31, and can simply be reused.
These patches are based on the sunxi-next branch from
git://github.com/linux-sunxi/linux-sunxi.git
Patch 1 adds basic H3 clocks.
Patch 2 adds pin sets for the H3 main PIO.
Patch 3 adds the DTSI for the H3.
Patch 4 adds a DTS for the Orange Pi Plus SBC, which these patches
were developed and tested with.
Changes since v4:
- drop the pll clock cleanup and use dummy clocks instead for now, Maxime
wants to take care of cleaning up the plls
- split the resets again (as in v1), drop the of_xlate
- fix all reported pinctrl mistakes
- remove memory node and timer frequency from dtsi
- rename the bus gates to bus_*
- clean up the bus gates driver
Changes since v3:
- add a clock driver specific to the bus gates instead of listing parents in
the DTSI
- skip the holes in the reset controller with of_xlate()
Changes since v2:
- add mbus clock
- add Maxime's suggestion to take the substring up to the first "_" as name
for the divs base clock
- use A31 pll6 for H3 pll6
- use a clock similar to the new simple gates for H3 bus gates
- drop the pinctrl-as-module patch since pinctrl and gpio don't seem to be
ready for removable drivers
- documentation and machine support are merged already
Changes since v1:
- Update sunxi README in Documentation
- Add the multiple parents gates and use them for bus-gates instead of
ahb1, ahb2, apb1 and apb2 gates
- Merge the pll8 clock with sun6i pll6
- Merge the ahb12, apb1 and apb2 resets to bus-resets with own compatible
- Add sun6i_timer_init to sun8i machine
- Remove the single SoC names from machine definition, its sun8i family
- Make the pinctrl driver tristate and put its Kconfig entry in the right order
- Rename pinctrl "scr" to "sim" and clock "sim" to "scr" to match user manual
- Remove the address paragraph from GPL in dts and dtsi
- Some style cleanup and line wrapping in dtsi
- Add ARM architected timers
- dmaengine isn't included anymore, it is merged already
Best Regards,
Jens
Jens Kuske (4):
clk: sunxi: Add H3 clocks support
pinctrl: sunxi: Add H3 PIO controller support
ARM: dts: sunxi: Add Allwinner H3 DTSI
ARM: dts: sun8i: Add Orange Pi Plus support
Documentation/devicetree/bindings/clock/sunxi.txt | 2 +
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 77 +++
arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++
drivers/clk/sunxi/Makefile | 1 +
drivers/clk/sunxi/clk-sun8i-bus-gates.c | 112 +++++
drivers/clk/sunxi/clk-sunxi.c | 6 +
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c | 515 +++++++++++++++++++++
11 files changed, 1218 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
create mode 100644 drivers/clk/sunxi/clk-sun8i-bus-gates.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
--
2.6.3
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 0/4] ARM: sunxi: Allwinner H3 support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij
Cc: Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, Jens Kuske, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
Hi everyone,
This is v5 of my patch series introducing basic kernel support for Allwinner's
H3 SoC. It mainly adds basic clocks, resets and pinctrl. It also adds
interrupts, timers, watchdog, RTC, dmaengine, MMC and UARTs, which are mostly
compatible to those in earlier SoCs like A23 and A31, and can simply be reused.
These patches are based on the sunxi-next branch from
git://github.com/linux-sunxi/linux-sunxi.git
Patch 1 adds basic H3 clocks.
Patch 2 adds pin sets for the H3 main PIO.
Patch 3 adds the DTSI for the H3.
Patch 4 adds a DTS for the Orange Pi Plus SBC, which these patches
were developed and tested with.
Changes since v4:
- drop the pll clock cleanup and use dummy clocks instead for now, Maxime
wants to take care of cleaning up the plls
- split the resets again (as in v1), drop the of_xlate
- fix all reported pinctrl mistakes
- remove memory node and timer frequency from dtsi
- rename the bus gates to bus_*
- clean up the bus gates driver
Changes since v3:
- add a clock driver specific to the bus gates instead of listing parents in
the DTSI
- skip the holes in the reset controller with of_xlate()
Changes since v2:
- add mbus clock
- add Maxime's suggestion to take the substring up to the first "_" as name
for the divs base clock
- use A31 pll6 for H3 pll6
- use a clock similar to the new simple gates for H3 bus gates
- drop the pinctrl-as-module patch since pinctrl and gpio don't seem to be
ready for removable drivers
- documentation and machine support are merged already
Changes since v1:
- Update sunxi README in Documentation
- Add the multiple parents gates and use them for bus-gates instead of
ahb1, ahb2, apb1 and apb2 gates
- Merge the pll8 clock with sun6i pll6
- Merge the ahb12, apb1 and apb2 resets to bus-resets with own compatible
- Add sun6i_timer_init to sun8i machine
- Remove the single SoC names from machine definition, its sun8i family
- Make the pinctrl driver tristate and put its Kconfig entry in the right order
- Rename pinctrl "scr" to "sim" and clock "sim" to "scr" to match user manual
- Remove the address paragraph from GPL in dts and dtsi
- Some style cleanup and line wrapping in dtsi
- Add ARM architected timers
- dmaengine isn't included anymore, it is merged already
Best Regards,
Jens
Jens Kuske (4):
clk: sunxi: Add H3 clocks support
pinctrl: sunxi: Add H3 PIO controller support
ARM: dts: sunxi: Add Allwinner H3 DTSI
ARM: dts: sun8i: Add Orange Pi Plus support
Documentation/devicetree/bindings/clock/sunxi.txt | 2 +
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 77 +++
arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++
drivers/clk/sunxi/Makefile | 1 +
drivers/clk/sunxi/clk-sun8i-bus-gates.c | 112 +++++
drivers/clk/sunxi/clk-sunxi.c | 6 +
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c | 515 +++++++++++++++++++++
11 files changed, 1218 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
create mode 100644 drivers/clk/sunxi/clk-sun8i-bus-gates.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
--
2.6.3
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 0/4] ARM: sunxi: Allwinner H3 support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: linux-arm-kernel
Hi everyone,
This is v5 of my patch series introducing basic kernel support for Allwinner's
H3 SoC. It mainly adds basic clocks, resets and pinctrl. It also adds
interrupts, timers, watchdog, RTC, dmaengine, MMC and UARTs, which are mostly
compatible to those in earlier SoCs like A23 and A31, and can simply be reused.
These patches are based on the sunxi-next branch from
git://github.com/linux-sunxi/linux-sunxi.git
Patch 1 adds basic H3 clocks.
Patch 2 adds pin sets for the H3 main PIO.
Patch 3 adds the DTSI for the H3.
Patch 4 adds a DTS for the Orange Pi Plus SBC, which these patches
were developed and tested with.
Changes since v4:
- drop the pll clock cleanup and use dummy clocks instead for now, Maxime
wants to take care of cleaning up the plls
- split the resets again (as in v1), drop the of_xlate
- fix all reported pinctrl mistakes
- remove memory node and timer frequency from dtsi
- rename the bus gates to bus_*
- clean up the bus gates driver
Changes since v3:
- add a clock driver specific to the bus gates instead of listing parents in
the DTSI
- skip the holes in the reset controller with of_xlate()
Changes since v2:
- add mbus clock
- add Maxime's suggestion to take the substring up to the first "_" as name
for the divs base clock
- use A31 pll6 for H3 pll6
- use a clock similar to the new simple gates for H3 bus gates
- drop the pinctrl-as-module patch since pinctrl and gpio don't seem to be
ready for removable drivers
- documentation and machine support are merged already
Changes since v1:
- Update sunxi README in Documentation
- Add the multiple parents gates and use them for bus-gates instead of
ahb1, ahb2, apb1 and apb2 gates
- Merge the pll8 clock with sun6i pll6
- Merge the ahb12, apb1 and apb2 resets to bus-resets with own compatible
- Add sun6i_timer_init to sun8i machine
- Remove the single SoC names from machine definition, its sun8i family
- Make the pinctrl driver tristate and put its Kconfig entry in the right order
- Rename pinctrl "scr" to "sim" and clock "sim" to "scr" to match user manual
- Remove the address paragraph from GPL in dts and dtsi
- Some style cleanup and line wrapping in dtsi
- Add ARM architected timers
- dmaengine isn't included anymore, it is merged already
Best Regards,
Jens
Jens Kuske (4):
clk: sunxi: Add H3 clocks support
pinctrl: sunxi: Add H3 PIO controller support
ARM: dts: sunxi: Add Allwinner H3 DTSI
ARM: dts: sun8i: Add Orange Pi Plus support
Documentation/devicetree/bindings/clock/sunxi.txt | 2 +
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 77 +++
arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++
drivers/clk/sunxi/Makefile | 1 +
drivers/clk/sunxi/clk-sun8i-bus-gates.c | 112 +++++
drivers/clk/sunxi/clk-sunxi.c | 6 +
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c | 515 +++++++++++++++++++++
11 files changed, 1218 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
create mode 100644 drivers/clk/sunxi/clk-sun8i-bus-gates.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
--
2.6.3
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/4] clk: sunxi: Add H3 clocks support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij
Cc: Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, Jens Kuske, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
The H3 clock control unit is similar to the those of other sun8i family
members like the A23.
It adds a new bus gates clock similar to the simple gates, but with a
different parent clock for each single gate.
Some of the gates use the new AHB2 clock as parent, whose clock source
is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
is mostly based on Allwinner kernel source code.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
Documentation/devicetree/bindings/clock/sunxi.txt | 2 +
drivers/clk/sunxi/Makefile | 1 +
drivers/clk/sunxi/clk-sun8i-bus-gates.c | 112 ++++++++++++++++++++++
drivers/clk/sunxi/clk-sunxi.c | 6 ++
4 files changed, 121 insertions(+)
create mode 100644 drivers/clk/sunxi/clk-sun8i-bus-gates.c
diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 153ac72..437962d 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -29,6 +29,7 @@ Required properties:
"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
"allwinner,sun9i-a80-cpus-clk" - for the CPUS on A80
"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
+ "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
@@ -56,6 +57,7 @@ Required properties:
"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
+ "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3
"allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80
"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
index 103efab..abf4916 100644
--- a/drivers/clk/sunxi/Makefile
+++ b/drivers/clk/sunxi/Makefile
@@ -10,6 +10,7 @@ obj-y += clk-a10-pll2.o
obj-y += clk-a20-gmac.o
obj-y += clk-mod0.o
obj-y += clk-simple-gates.o
+obj-y += clk-sun8i-bus-gates.o
obj-y += clk-sun8i-mbus.o
obj-y += clk-sun9i-core.o
obj-y += clk-sun9i-mmc.o
diff --git a/drivers/clk/sunxi/clk-sun8i-bus-gates.c b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
new file mode 100644
index 0000000..7ab60c5
--- /dev/null
+++ b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
@@ -0,0 +1,112 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * Based on clk-simple-gates.c, which is:
+ * Copyright 2015 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+static DEFINE_SPINLOCK(gates_lock);
+
+static void __init sun8i_h3_bus_gates_init(struct device_node *node)
+{
+ static const char * const names[] = { "ahb1", "ahb2", "apb1", "apb2" };
+ enum { AHB1, AHB2, APB1, APB2, PARENT_MAX } clk_parent;
+ const char *parents[PARENT_MAX];
+ struct clk_onecell_data *clk_data;
+ const char *clk_name;
+ struct property *prop;
+ struct resource res;
+ void __iomem *clk_reg;
+ void __iomem *reg;
+ const __be32 *p;
+ int number, i;
+ u8 clk_bit;
+ u32 index;
+
+ reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+ if (IS_ERR(reg))
+ return;
+
+ for (i = 0; i < ARRAY_SIZE(names); i++) {
+ index = of_property_match_string(node, "clock-names",
+ names[i]);
+ if (index < 0)
+ return;
+
+ parents[i] = of_clk_get_parent_name(node, index);
+ }
+
+ clk_data = kmalloc(sizeof(struct clk_onecell_data), GFP_KERNEL);
+ if (!clk_data)
+ goto err_unmap;
+
+ number = of_property_count_u32_elems(node, "clock-indices");
+ of_property_read_u32_index(node, "clock-indices", number - 1, &number);
+
+ clk_data->clks = kcalloc(number + 1, sizeof(struct clk *), GFP_KERNEL);
+ if (!clk_data->clks)
+ goto err_free_data;
+
+ i = 0;
+ of_property_for_each_u32(node, "clock-indices", prop, p, index) {
+ of_property_read_string_index(node, "clock-output-names",
+ i, &clk_name);
+
+ if (index == 17 || (index >= 29 && index <= 31))
+ clk_parent = AHB2;
+ else if (index <= 63 || index >= 128)
+ clk_parent = AHB1;
+ else if (index >= 64 && index <= 95)
+ clk_parent = APB1;
+ else if (index >= 96 && index <= 127)
+ clk_parent = APB2;
+
+ clk_reg = reg + 4 * (index / 32);
+ clk_bit = index % 32;
+
+ clk_data->clks[index] = clk_register_gate(NULL, clk_name,
+ parents[clk_parent],
+ 0, clk_reg, clk_bit,
+ 0, &gates_lock);
+ i++;
+
+ if (IS_ERR(clk_data->clks[index])) {
+ WARN_ON(true);
+ continue;
+ }
+ }
+
+ clk_data->clk_num = number + 1;
+ of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+
+ return;
+
+err_free_data:
+ kfree(clk_data);
+err_unmap:
+ iounmap(reg);
+ of_address_to_resource(node, 0, &res);
+ release_mem_region(res.start, resource_size(&res));
+}
+
+CLK_OF_DECLARE(sun8i_h3_bus_gates, "allwinner,sun8i-h3-bus-gates-clk",
+ sun8i_h3_bus_gates_init);
diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
index 9c79af0c..5ba2188 100644
--- a/drivers/clk/sunxi/clk-sunxi.c
+++ b/drivers/clk/sunxi/clk-sunxi.c
@@ -778,6 +778,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
.shift = 12,
};
+static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
+ .shift = 0,
+};
+
static void __init sunxi_mux_clk_setup(struct device_node *node,
struct mux_data *data)
{
@@ -1130,6 +1134,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
static const struct of_device_id clk_mux_match[] __initconst = {
{.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
{.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
+ {.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
{}
};
@@ -1212,6 +1217,7 @@ CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
CLK_OF_DECLARE(sun8i_a33_clk_init, "allwinner,sun8i-a33", sun6i_init_clocks);
+CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
static void __init sun9i_init_clocks(struct device_node *node)
{
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 1/4] clk: sunxi: Add H3 clocks support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij
Cc: Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, Jens Kuske, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
The H3 clock control unit is similar to the those of other sun8i family
members like the A23.
It adds a new bus gates clock similar to the simple gates, but with a
different parent clock for each single gate.
Some of the gates use the new AHB2 clock as parent, whose clock source
is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
is mostly based on Allwinner kernel source code.
Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
Documentation/devicetree/bindings/clock/sunxi.txt | 2 +
drivers/clk/sunxi/Makefile | 1 +
drivers/clk/sunxi/clk-sun8i-bus-gates.c | 112 ++++++++++++++++++++++
drivers/clk/sunxi/clk-sunxi.c | 6 ++
4 files changed, 121 insertions(+)
create mode 100644 drivers/clk/sunxi/clk-sun8i-bus-gates.c
diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 153ac72..437962d 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -29,6 +29,7 @@ Required properties:
"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
"allwinner,sun9i-a80-cpus-clk" - for the CPUS on A80
"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
+ "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
@@ -56,6 +57,7 @@ Required properties:
"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
+ "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3
"allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80
"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
index 103efab..abf4916 100644
--- a/drivers/clk/sunxi/Makefile
+++ b/drivers/clk/sunxi/Makefile
@@ -10,6 +10,7 @@ obj-y += clk-a10-pll2.o
obj-y += clk-a20-gmac.o
obj-y += clk-mod0.o
obj-y += clk-simple-gates.o
+obj-y += clk-sun8i-bus-gates.o
obj-y += clk-sun8i-mbus.o
obj-y += clk-sun9i-core.o
obj-y += clk-sun9i-mmc.o
diff --git a/drivers/clk/sunxi/clk-sun8i-bus-gates.c b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
new file mode 100644
index 0000000..7ab60c5
--- /dev/null
+++ b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
@@ -0,0 +1,112 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * Based on clk-simple-gates.c, which is:
+ * Copyright 2015 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+static DEFINE_SPINLOCK(gates_lock);
+
+static void __init sun8i_h3_bus_gates_init(struct device_node *node)
+{
+ static const char * const names[] = { "ahb1", "ahb2", "apb1", "apb2" };
+ enum { AHB1, AHB2, APB1, APB2, PARENT_MAX } clk_parent;
+ const char *parents[PARENT_MAX];
+ struct clk_onecell_data *clk_data;
+ const char *clk_name;
+ struct property *prop;
+ struct resource res;
+ void __iomem *clk_reg;
+ void __iomem *reg;
+ const __be32 *p;
+ int number, i;
+ u8 clk_bit;
+ u32 index;
+
+ reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+ if (IS_ERR(reg))
+ return;
+
+ for (i = 0; i < ARRAY_SIZE(names); i++) {
+ index = of_property_match_string(node, "clock-names",
+ names[i]);
+ if (index < 0)
+ return;
+
+ parents[i] = of_clk_get_parent_name(node, index);
+ }
+
+ clk_data = kmalloc(sizeof(struct clk_onecell_data), GFP_KERNEL);
+ if (!clk_data)
+ goto err_unmap;
+
+ number = of_property_count_u32_elems(node, "clock-indices");
+ of_property_read_u32_index(node, "clock-indices", number - 1, &number);
+
+ clk_data->clks = kcalloc(number + 1, sizeof(struct clk *), GFP_KERNEL);
+ if (!clk_data->clks)
+ goto err_free_data;
+
+ i = 0;
+ of_property_for_each_u32(node, "clock-indices", prop, p, index) {
+ of_property_read_string_index(node, "clock-output-names",
+ i, &clk_name);
+
+ if (index == 17 || (index >= 29 && index <= 31))
+ clk_parent = AHB2;
+ else if (index <= 63 || index >= 128)
+ clk_parent = AHB1;
+ else if (index >= 64 && index <= 95)
+ clk_parent = APB1;
+ else if (index >= 96 && index <= 127)
+ clk_parent = APB2;
+
+ clk_reg = reg + 4 * (index / 32);
+ clk_bit = index % 32;
+
+ clk_data->clks[index] = clk_register_gate(NULL, clk_name,
+ parents[clk_parent],
+ 0, clk_reg, clk_bit,
+ 0, &gates_lock);
+ i++;
+
+ if (IS_ERR(clk_data->clks[index])) {
+ WARN_ON(true);
+ continue;
+ }
+ }
+
+ clk_data->clk_num = number + 1;
+ of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+
+ return;
+
+err_free_data:
+ kfree(clk_data);
+err_unmap:
+ iounmap(reg);
+ of_address_to_resource(node, 0, &res);
+ release_mem_region(res.start, resource_size(&res));
+}
+
+CLK_OF_DECLARE(sun8i_h3_bus_gates, "allwinner,sun8i-h3-bus-gates-clk",
+ sun8i_h3_bus_gates_init);
diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
index 9c79af0c..5ba2188 100644
--- a/drivers/clk/sunxi/clk-sunxi.c
+++ b/drivers/clk/sunxi/clk-sunxi.c
@@ -778,6 +778,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
.shift = 12,
};
+static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
+ .shift = 0,
+};
+
static void __init sunxi_mux_clk_setup(struct device_node *node,
struct mux_data *data)
{
@@ -1130,6 +1134,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
static const struct of_device_id clk_mux_match[] __initconst = {
{.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
{.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
+ {.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
{}
};
@@ -1212,6 +1217,7 @@ CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
CLK_OF_DECLARE(sun8i_a33_clk_init, "allwinner,sun8i-a33", sun6i_init_clocks);
+CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
static void __init sun9i_init_clocks(struct device_node *node)
{
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 1/4] clk: sunxi: Add H3 clocks support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: linux-arm-kernel
The H3 clock control unit is similar to the those of other sun8i family
members like the A23.
It adds a new bus gates clock similar to the simple gates, but with a
different parent clock for each single gate.
Some of the gates use the new AHB2 clock as parent, whose clock source
is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
is mostly based on Allwinner kernel source code.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
Documentation/devicetree/bindings/clock/sunxi.txt | 2 +
drivers/clk/sunxi/Makefile | 1 +
drivers/clk/sunxi/clk-sun8i-bus-gates.c | 112 ++++++++++++++++++++++
drivers/clk/sunxi/clk-sunxi.c | 6 ++
4 files changed, 121 insertions(+)
create mode 100644 drivers/clk/sunxi/clk-sun8i-bus-gates.c
diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 153ac72..437962d 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -29,6 +29,7 @@ Required properties:
"allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
"allwinner,sun9i-a80-cpus-clk" - for the CPUS on A80
"allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
+ "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
"allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
"allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
"allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
@@ -56,6 +57,7 @@ Required properties:
"allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
"allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
"allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
+ "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3
"allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80
"allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
"allwinner,sun4i-a10-mmc-clk" - for the MMC clock
diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
index 103efab..abf4916 100644
--- a/drivers/clk/sunxi/Makefile
+++ b/drivers/clk/sunxi/Makefile
@@ -10,6 +10,7 @@ obj-y += clk-a10-pll2.o
obj-y += clk-a20-gmac.o
obj-y += clk-mod0.o
obj-y += clk-simple-gates.o
+obj-y += clk-sun8i-bus-gates.o
obj-y += clk-sun8i-mbus.o
obj-y += clk-sun9i-core.o
obj-y += clk-sun9i-mmc.o
diff --git a/drivers/clk/sunxi/clk-sun8i-bus-gates.c b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
new file mode 100644
index 0000000..7ab60c5
--- /dev/null
+++ b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
@@ -0,0 +1,112 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * Based on clk-simple-gates.c, which is:
+ * Copyright 2015 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+static DEFINE_SPINLOCK(gates_lock);
+
+static void __init sun8i_h3_bus_gates_init(struct device_node *node)
+{
+ static const char * const names[] = { "ahb1", "ahb2", "apb1", "apb2" };
+ enum { AHB1, AHB2, APB1, APB2, PARENT_MAX } clk_parent;
+ const char *parents[PARENT_MAX];
+ struct clk_onecell_data *clk_data;
+ const char *clk_name;
+ struct property *prop;
+ struct resource res;
+ void __iomem *clk_reg;
+ void __iomem *reg;
+ const __be32 *p;
+ int number, i;
+ u8 clk_bit;
+ u32 index;
+
+ reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+ if (IS_ERR(reg))
+ return;
+
+ for (i = 0; i < ARRAY_SIZE(names); i++) {
+ index = of_property_match_string(node, "clock-names",
+ names[i]);
+ if (index < 0)
+ return;
+
+ parents[i] = of_clk_get_parent_name(node, index);
+ }
+
+ clk_data = kmalloc(sizeof(struct clk_onecell_data), GFP_KERNEL);
+ if (!clk_data)
+ goto err_unmap;
+
+ number = of_property_count_u32_elems(node, "clock-indices");
+ of_property_read_u32_index(node, "clock-indices", number - 1, &number);
+
+ clk_data->clks = kcalloc(number + 1, sizeof(struct clk *), GFP_KERNEL);
+ if (!clk_data->clks)
+ goto err_free_data;
+
+ i = 0;
+ of_property_for_each_u32(node, "clock-indices", prop, p, index) {
+ of_property_read_string_index(node, "clock-output-names",
+ i, &clk_name);
+
+ if (index == 17 || (index >= 29 && index <= 31))
+ clk_parent = AHB2;
+ else if (index <= 63 || index >= 128)
+ clk_parent = AHB1;
+ else if (index >= 64 && index <= 95)
+ clk_parent = APB1;
+ else if (index >= 96 && index <= 127)
+ clk_parent = APB2;
+
+ clk_reg = reg + 4 * (index / 32);
+ clk_bit = index % 32;
+
+ clk_data->clks[index] = clk_register_gate(NULL, clk_name,
+ parents[clk_parent],
+ 0, clk_reg, clk_bit,
+ 0, &gates_lock);
+ i++;
+
+ if (IS_ERR(clk_data->clks[index])) {
+ WARN_ON(true);
+ continue;
+ }
+ }
+
+ clk_data->clk_num = number + 1;
+ of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
+
+ return;
+
+err_free_data:
+ kfree(clk_data);
+err_unmap:
+ iounmap(reg);
+ of_address_to_resource(node, 0, &res);
+ release_mem_region(res.start, resource_size(&res));
+}
+
+CLK_OF_DECLARE(sun8i_h3_bus_gates, "allwinner,sun8i-h3-bus-gates-clk",
+ sun8i_h3_bus_gates_init);
diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
index 9c79af0c..5ba2188 100644
--- a/drivers/clk/sunxi/clk-sunxi.c
+++ b/drivers/clk/sunxi/clk-sunxi.c
@@ -778,6 +778,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
.shift = 12,
};
+static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
+ .shift = 0,
+};
+
static void __init sunxi_mux_clk_setup(struct device_node *node,
struct mux_data *data)
{
@@ -1130,6 +1134,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
static const struct of_device_id clk_mux_match[] __initconst = {
{.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
{.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
+ {.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
{}
};
@@ -1212,6 +1217,7 @@ CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
CLK_OF_DECLARE(sun8i_a33_clk_init, "allwinner,sun8i-a33", sun6i_init_clocks);
+CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
static void __init sun9i_init_clocks(struct device_node *node)
{
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij
Cc: Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, Jens Kuske, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
The H3 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c | 515 +++++++++++++++++++++
4 files changed, 521 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index b321b26..e6ba602 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -18,6 +18,7 @@ Required properties:
"allwinner,sun8i-a23-r-pinctrl"
"allwinner,sun8i-a33-pinctrl"
"allwinner,sun8i-a83t-pinctrl"
+ "allwinner,sun8i-h3-pinctrl"
- reg: Should contain the register physical address and length for the
pin controller.
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index e68fd95..89ab7f5 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -51,6 +51,10 @@ config PINCTRL_SUN8I_A23_R
depends on RESET_CONTROLLER
select PINCTRL_SUNXI_COMMON
+config PINCTRL_SUN8I_H3
+ def_bool MACH_SUN8I
+ select PINCTRL_SUNXI_COMMON
+
config PINCTRL_SUN9I_A80
def_bool MACH_SUN9I
select PINCTRL_SUNXI_COMMON
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index e080290..6bd818e 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -13,4 +13,5 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23) += pinctrl-sun8i-a23.o
obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
+obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
new file mode 100644
index 0000000..77d4cf0
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
@@ -0,0 +1,515 @@
+/*
+ * Allwinner H3 SoCs pinctrl driver.
+ *
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * Based on pinctrl-sun8i-a23.c, which is:
+ * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun8i_h3_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), /* PA_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), /* PA_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), /* PA_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), /* PA_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), /* PA_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x3, "pwm0"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), /* PA_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* PWREN */
+ SUNXI_FUNCTION(0x3, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), /* PA_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), /* PA_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DATA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), /* PA_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), /* PA_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DET */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), /* PA_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x3, "di"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)), /* PA_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x3, "di"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)), /* PA_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CS */
+ SUNXI_FUNCTION(0x3, "uart3"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)), /* PA_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)), /* PA_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)), /* PA_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x3, "uart3"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)), /* PA_EINT16 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* OUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)), /* PA_EINT17 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* SYNC */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)), /* PA_EINT18 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)), /* PA_EINT19 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DOUT */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPEN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)), /* PA_EINT20 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DIN */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPPP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)), /* PA_EINT21 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* MOSI */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* MISO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0")), /* CE0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CMD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0")), /* RB1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand"), /* DQS */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* RST */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXCTL/RXDV */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* CRS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXCTL/TXEN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* CLKIN/COL */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* MDC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* MDIO */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* PCLK */
+ SUNXI_FUNCTION(0x3, "ts")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "ts")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* HSYNC */
+ SUNXI_FUNCTION(0x3, "ts")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* VSYNC */
+ SUNXI_FUNCTION(0x3, "ts")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D0 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D1 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D2 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D3 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D4 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D5 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D6 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D7 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SCK */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SDA */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SDA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out")),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out")),
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag")), /* MS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag")), /* DI */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0")), /* TX */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag")), /* DO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0")), /* RX */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag")), /* CK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out")),
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), /* PG_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), /* PG_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), /* PG_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), /* PG_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), /* PG_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), /* PG_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), /* PG_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)), /* PG_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)), /* PG_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)), /* PG_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* SYNC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)), /* PG_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)), /* PG_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DOUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)), /* PG_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)), /* PG_EINT13 */
+};
+
+static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
+ .pins = sun8i_h3_pins,
+ .npins = ARRAY_SIZE(sun8i_h3_pins),
+ .irq_banks = 2,
+};
+
+static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev,
+ &sun8i_h3_pinctrl_data);
+}
+
+static const struct of_device_id sun8i_h3_pinctrl_match[] = {
+ { .compatible = "allwinner,sun8i-h3-pinctrl", },
+ {}
+};
+
+static struct platform_driver sun8i_h3_pinctrl_driver = {
+ .probe = sun8i_h3_pinctrl_probe,
+ .driver = {
+ .name = "sun8i-h3-pinctrl",
+ .of_match_table = sun8i_h3_pinctrl_match,
+ },
+};
+builtin_platform_driver(sun8i_h3_pinctrl_driver);
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij
Cc: Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, Jens Kuske, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
The H3 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.
Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c | 515 +++++++++++++++++++++
4 files changed, 521 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index b321b26..e6ba602 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -18,6 +18,7 @@ Required properties:
"allwinner,sun8i-a23-r-pinctrl"
"allwinner,sun8i-a33-pinctrl"
"allwinner,sun8i-a83t-pinctrl"
+ "allwinner,sun8i-h3-pinctrl"
- reg: Should contain the register physical address and length for the
pin controller.
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index e68fd95..89ab7f5 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -51,6 +51,10 @@ config PINCTRL_SUN8I_A23_R
depends on RESET_CONTROLLER
select PINCTRL_SUNXI_COMMON
+config PINCTRL_SUN8I_H3
+ def_bool MACH_SUN8I
+ select PINCTRL_SUNXI_COMMON
+
config PINCTRL_SUN9I_A80
def_bool MACH_SUN9I
select PINCTRL_SUNXI_COMMON
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index e080290..6bd818e 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -13,4 +13,5 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23) += pinctrl-sun8i-a23.o
obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
+obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
new file mode 100644
index 0000000..77d4cf0
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
@@ -0,0 +1,515 @@
+/*
+ * Allwinner H3 SoCs pinctrl driver.
+ *
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * Based on pinctrl-sun8i-a23.c, which is:
+ * Copyright (C) 2014 Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
+ * Copyright (C) 2014 Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun8i_h3_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), /* PA_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), /* PA_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), /* PA_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), /* PA_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), /* PA_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x3, "pwm0"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), /* PA_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* PWREN */
+ SUNXI_FUNCTION(0x3, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), /* PA_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), /* PA_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DATA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), /* PA_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), /* PA_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DET */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), /* PA_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x3, "di"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)), /* PA_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x3, "di"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)), /* PA_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CS */
+ SUNXI_FUNCTION(0x3, "uart3"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)), /* PA_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)), /* PA_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)), /* PA_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x3, "uart3"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)), /* PA_EINT16 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* OUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)), /* PA_EINT17 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* SYNC */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)), /* PA_EINT18 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)), /* PA_EINT19 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DOUT */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPEN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)), /* PA_EINT20 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DIN */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPPP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)), /* PA_EINT21 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* MOSI */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* MISO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0")), /* CE0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CMD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0")), /* RB1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand"), /* DQS */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* RST */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXCTL/RXDV */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* CRS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXCTL/TXEN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* CLKIN/COL */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* MDC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* MDIO */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* PCLK */
+ SUNXI_FUNCTION(0x3, "ts")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "ts")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* HSYNC */
+ SUNXI_FUNCTION(0x3, "ts")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* VSYNC */
+ SUNXI_FUNCTION(0x3, "ts")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D0 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D1 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D2 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D3 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D4 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D5 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D6 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D7 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SCK */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SDA */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SDA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out")),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out")),
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag")), /* MS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag")), /* DI */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0")), /* TX */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag")), /* DO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0")), /* RX */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag")), /* CK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out")),
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), /* PG_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), /* PG_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), /* PG_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), /* PG_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), /* PG_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), /* PG_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), /* PG_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)), /* PG_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)), /* PG_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)), /* PG_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* SYNC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)), /* PG_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)), /* PG_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DOUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)), /* PG_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)), /* PG_EINT13 */
+};
+
+static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
+ .pins = sun8i_h3_pins,
+ .npins = ARRAY_SIZE(sun8i_h3_pins),
+ .irq_banks = 2,
+};
+
+static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev,
+ &sun8i_h3_pinctrl_data);
+}
+
+static const struct of_device_id sun8i_h3_pinctrl_match[] = {
+ { .compatible = "allwinner,sun8i-h3-pinctrl", },
+ {}
+};
+
+static struct platform_driver sun8i_h3_pinctrl_driver = {
+ .probe = sun8i_h3_pinctrl_probe,
+ .driver = {
+ .name = "sun8i-h3-pinctrl",
+ .of_match_table = sun8i_h3_pinctrl_match,
+ },
+};
+builtin_platform_driver(sun8i_h3_pinctrl_driver);
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: linux-arm-kernel
The H3 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
.../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
drivers/pinctrl/sunxi/Kconfig | 4 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c | 515 +++++++++++++++++++++
4 files changed, 521 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index b321b26..e6ba602 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -18,6 +18,7 @@ Required properties:
"allwinner,sun8i-a23-r-pinctrl"
"allwinner,sun8i-a33-pinctrl"
"allwinner,sun8i-a83t-pinctrl"
+ "allwinner,sun8i-h3-pinctrl"
- reg: Should contain the register physical address and length for the
pin controller.
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index e68fd95..89ab7f5 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -51,6 +51,10 @@ config PINCTRL_SUN8I_A23_R
depends on RESET_CONTROLLER
select PINCTRL_SUNXI_COMMON
+config PINCTRL_SUN8I_H3
+ def_bool MACH_SUN8I
+ select PINCTRL_SUNXI_COMMON
+
config PINCTRL_SUN9I_A80
def_bool MACH_SUN9I
select PINCTRL_SUNXI_COMMON
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index e080290..6bd818e 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -13,4 +13,5 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23) += pinctrl-sun8i-a23.o
obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o
obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o
obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
+obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
new file mode 100644
index 0000000..77d4cf0
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
@@ -0,0 +1,515 @@
+/*
+ * Allwinner H3 SoCs pinctrl driver.
+ *
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * Based on pinctrl-sun8i-a23.c, which is:
+ * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun8i_h3_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), /* PA_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), /* PA_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), /* PA_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), /* PA_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), /* PA_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x3, "pwm0"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), /* PA_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* PWREN */
+ SUNXI_FUNCTION(0x3, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), /* PA_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), /* PA_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DATA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), /* PA_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), /* PA_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "sim"), /* DET */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), /* PA_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
+ SUNXI_FUNCTION(0x3, "di"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)), /* PA_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
+ SUNXI_FUNCTION(0x3, "di"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)), /* PA_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CS */
+ SUNXI_FUNCTION(0x3, "uart3"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)), /* PA_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)), /* PA_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)), /* PA_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x3, "uart3"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)), /* PA_EINT16 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "spdif"), /* OUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)), /* PA_EINT17 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* SYNC */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)), /* PA_EINT18 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)), /* PA_EINT19 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DOUT */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPEN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)), /* PA_EINT20 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s0"), /* DIN */
+ SUNXI_FUNCTION(0x3, "sim"), /* VPPPP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)), /* PA_EINT21 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* MOSI */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* MISO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x3, "spi0")), /* CS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0")), /* CE0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* CMD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0")), /* RB1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* D7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand"), /* DQS */
+ SUNXI_FUNCTION(0x3, "mmc2")), /* RST */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXD0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXCTL/RXDV */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* RXERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXD0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* CRS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXCTL/TXEN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* TXERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* CLKIN/COL */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* MDC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac")), /* MDIO */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* PCLK */
+ SUNXI_FUNCTION(0x3, "ts")), /* CLK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "ts")), /* ERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* HSYNC */
+ SUNXI_FUNCTION(0x3, "ts")), /* SYNC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* VSYNC */
+ SUNXI_FUNCTION(0x3, "ts")), /* DVLD */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D0 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D1 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D2 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D3 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D4 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D5 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D6 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* D7 */
+ SUNXI_FUNCTION(0x3, "ts")), /* D7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SCK */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "csi"), /* SDA */
+ SUNXI_FUNCTION(0x3, "i2c2")), /* SDA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out")),
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out")),
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag")), /* MS */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag")), /* DI */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0")), /* TX */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag")), /* DO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0")), /* RX */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag")), /* CK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out")),
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), /* PG_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), /* PG_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), /* PG_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), /* PG_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), /* PG_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), /* PG_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), /* PG_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)), /* PG_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)), /* PG_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)), /* PG_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* SYNC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)), /* PG_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)), /* PG_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DOUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)), /* PG_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "i2s1"), /* DIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)), /* PG_EINT13 */
+};
+
+static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
+ .pins = sun8i_h3_pins,
+ .npins = ARRAY_SIZE(sun8i_h3_pins),
+ .irq_banks = 2,
+};
+
+static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev,
+ &sun8i_h3_pinctrl_data);
+}
+
+static const struct of_device_id sun8i_h3_pinctrl_match[] = {
+ { .compatible = "allwinner,sun8i-h3-pinctrl", },
+ {}
+};
+
+static struct platform_driver sun8i_h3_pinctrl_driver = {
+ .probe = sun8i_h3_pinctrl_probe,
+ .driver = {
+ .name = "sun8i-h3-pinctrl",
+ .of_match_table = sun8i_h3_pinctrl_match,
+ },
+};
+builtin_platform_driver(sun8i_h3_pinctrl_driver);
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij
Cc: Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, Jens Kuske, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 497 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
new file mode 100644
index 0000000..1524130e
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -0,0 +1,497 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ pll1: clk@01c20000 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-a23-pll1-clk";
+ reg = <0x01c20000 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll1";
+ };
+
+ /* dummy clock until actually implemented */
+ pll5: pll5_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ clock-output-names = "pll5";
+ };
+
+ pll6: clk@01c20028 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun6i-a31-pll6-clk";
+ reg = <0x01c20028 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll6", "pll6x2";
+ };
+
+ pll6d2: pll6d2_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clock-div = <2>;
+ clock-mult = <1>;
+ clocks = <&pll6 0>;
+ clock-output-names = "pll6d2";
+ };
+
+ /* dummy clock until pll6 can be reused */
+ pll8: pll8_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <1>;
+ clock-output-names = "pll8";
+ };
+
+ cpu: cpu_clk@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-cpu-clk";
+ reg = <0x01c20050 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+ clock-output-names = "cpu";
+ };
+
+ axi: axi_clk@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-axi-clk";
+ reg = <0x01c20050 0x4>;
+ clocks = <&cpu>;
+ clock-output-names = "axi";
+ };
+
+ ahb1: ahb1_clk@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun6i-a31-ahb1-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+ clock-output-names = "ahb1";
+ };
+
+ ahb2: ahb2_clk@01c2005c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-h3-ahb2-clk";
+ reg = <0x01c2005c 0x4>;
+ clocks = <&ahb1>, <&pll6d2>;
+ clock-output-names = "ahb2";
+ };
+
+ apb1: apb1_clk@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb0-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&ahb1>;
+ clock-output-names = "apb1";
+ };
+
+ apb2: apb2_clk@01c20058 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb1-clk";
+ reg = <0x01c20058 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
+ clock-output-names = "apb2";
+ };
+
+ bus_gates: clk@01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-h3-bus-gates-clk";
+ reg = <0x01c20060 0x14>;
+ clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
+ clock-names = "ahb1", "ahb2", "apb1", "apb2";
+ clock-indices = <5>, <6>, <8>,
+ <9>, <10>, <13>,
+ <14>, <17>, <18>,
+ <19>, <20>,
+ <21>, <23>,
+ <24>, <25>,
+ <26>, <27>,
+ <28>, <29>,
+ <30>, <31>, <32>,
+ <35>, <36>, <37>,
+ <40>, <41>, <43>,
+ <44>, <52>, <53>,
+ <54>, <64>,
+ <65>, <69>, <72>,
+ <76>, <77>, <78>,
+ <96>, <97>, <98>,
+ <112>, <113>,
+ <114>, <115>,
+ <116>, <128>, <135>;
+ clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
+ "bus_mmc1", "bus_mmc2", "bus_nand",
+ "bus_sdram", "bus_gmac", "bus_ts",
+ "bus_hstimer", "bus_spi0",
+ "bus_spi1", "bus_otg",
+ "bus_otg_ehci0", "bus_ehci1",
+ "bus_ehci2", "bus_ehci3",
+ "bus_otg_ohci0", "bus_ohci1",
+ "bus_ohci2", "bus_ohci3", "bus_ve",
+ "bus_lcd0", "bus_lcd1", "bus_deint",
+ "bus_csi", "bus_tve", "bus_hdmi",
+ "bus_de", "bus_gpu", "bus_msgbox",
+ "bus_spinlock", "bus_codec",
+ "bus_spdif", "bus_pio", "bus_ths",
+ "bus_i2s0", "bus_i2s1", "bus_i2s2",
+ "bus_i2c0", "bus_i2c1", "bus_i2c2",
+ "bus_uart0", "bus_uart1",
+ "bus_uart2", "bus_uart3",
+ "bus_scr", "bus_ephy", "bus_dbg";
+ };
+
+ mmc0_clk: clk@01c20088 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20088 0x4>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+ clock-output-names = "mmc0",
+ "mmc0_output",
+ "mmc0_sample";
+ };
+
+ mmc1_clk: clk@01c2008c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c2008c 0x4>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+ clock-output-names = "mmc1",
+ "mmc1_output",
+ "mmc1_sample";
+ };
+
+ mmc2_clk: clk@01c20090 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20090 0x4>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+ clock-output-names = "mmc2",
+ "mmc2_output",
+ "mmc2_sample";
+ };
+
+ mbus_clk: clk@01c2015c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-a23-mbus-clk";
+ reg = <0x01c2015c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5>;
+ clock-output-names = "mbus";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun8i-h3-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bus_gates 6>;
+ resets = <&ahb_rst 6>;
+ #dma-cells = <1>;
+ };
+
+ mmc0: mmc@01c0f000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&bus_gates 8>,
+ <&mmc0_clk 0>,
+ <&mmc0_clk 1>,
+ <&mmc0_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb_rst 8>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@01c10000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&bus_gates 9>,
+ <&mmc1_clk 0>,
+ <&mmc1_clk 1>,
+ <&mmc1_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb_rst 9>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@01c11000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&bus_gates 10>,
+ <&mmc2_clk 0>,
+ <&mmc2_clk 1>,
+ <&mmc2_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb_rst 10>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pio: pinctrl@01c20800 {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bus_gates 69>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PA4", "PA5";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins_a: mmc0@0 {
+ allwinner,pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin@0 {
+ allwinner,pins = "PF6";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc1_pins_a: mmc1@0 {
+ allwinner,pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ ahb_rst: reset@01c202c0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-ahb1-reset";
+ reg = <0x01c202c0 0xc>;
+ };
+
+ apb1_rst: reset@01c202d0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d0 0x4>;
+ };
+
+ apb2_rst: reset@01c202d8 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d8 0x4>;
+ };
+
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ wdt0: watchdog@01c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ uart0: serial@01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 112>;
+ resets = <&apb2_rst 16>;
+ dmas = <&dma 6>, <&dma 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial@01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 113>;
+ resets = <&apb2_rst 17>;
+ dmas = <&dma 7>, <&dma 7>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial@01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 114>;
+ resets = <&apb2_rst 18>;
+ dmas = <&dma 8>, <&dma 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial@01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 115>;
+ resets = <&apb2_rst 19>;
+ dmas = <&dma 9>, <&dma 9>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ gic: interrupt-controller@01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x1000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ rtc: rtc@01f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+};
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij
Cc: Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, Jens Kuske, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.
Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 497 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
new file mode 100644
index 0000000..1524130e
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -0,0 +1,497 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ pll1: clk@01c20000 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-a23-pll1-clk";
+ reg = <0x01c20000 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll1";
+ };
+
+ /* dummy clock until actually implemented */
+ pll5: pll5_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ clock-output-names = "pll5";
+ };
+
+ pll6: clk@01c20028 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun6i-a31-pll6-clk";
+ reg = <0x01c20028 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll6", "pll6x2";
+ };
+
+ pll6d2: pll6d2_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clock-div = <2>;
+ clock-mult = <1>;
+ clocks = <&pll6 0>;
+ clock-output-names = "pll6d2";
+ };
+
+ /* dummy clock until pll6 can be reused */
+ pll8: pll8_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <1>;
+ clock-output-names = "pll8";
+ };
+
+ cpu: cpu_clk@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-cpu-clk";
+ reg = <0x01c20050 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+ clock-output-names = "cpu";
+ };
+
+ axi: axi_clk@01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-axi-clk";
+ reg = <0x01c20050 0x4>;
+ clocks = <&cpu>;
+ clock-output-names = "axi";
+ };
+
+ ahb1: ahb1_clk@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun6i-a31-ahb1-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+ clock-output-names = "ahb1";
+ };
+
+ ahb2: ahb2_clk@01c2005c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-h3-ahb2-clk";
+ reg = <0x01c2005c 0x4>;
+ clocks = <&ahb1>, <&pll6d2>;
+ clock-output-names = "ahb2";
+ };
+
+ apb1: apb1_clk@01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb0-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&ahb1>;
+ clock-output-names = "apb1";
+ };
+
+ apb2: apb2_clk@01c20058 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb1-clk";
+ reg = <0x01c20058 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
+ clock-output-names = "apb2";
+ };
+
+ bus_gates: clk@01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-h3-bus-gates-clk";
+ reg = <0x01c20060 0x14>;
+ clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
+ clock-names = "ahb1", "ahb2", "apb1", "apb2";
+ clock-indices = <5>, <6>, <8>,
+ <9>, <10>, <13>,
+ <14>, <17>, <18>,
+ <19>, <20>,
+ <21>, <23>,
+ <24>, <25>,
+ <26>, <27>,
+ <28>, <29>,
+ <30>, <31>, <32>,
+ <35>, <36>, <37>,
+ <40>, <41>, <43>,
+ <44>, <52>, <53>,
+ <54>, <64>,
+ <65>, <69>, <72>,
+ <76>, <77>, <78>,
+ <96>, <97>, <98>,
+ <112>, <113>,
+ <114>, <115>,
+ <116>, <128>, <135>;
+ clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
+ "bus_mmc1", "bus_mmc2", "bus_nand",
+ "bus_sdram", "bus_gmac", "bus_ts",
+ "bus_hstimer", "bus_spi0",
+ "bus_spi1", "bus_otg",
+ "bus_otg_ehci0", "bus_ehci1",
+ "bus_ehci2", "bus_ehci3",
+ "bus_otg_ohci0", "bus_ohci1",
+ "bus_ohci2", "bus_ohci3", "bus_ve",
+ "bus_lcd0", "bus_lcd1", "bus_deint",
+ "bus_csi", "bus_tve", "bus_hdmi",
+ "bus_de", "bus_gpu", "bus_msgbox",
+ "bus_spinlock", "bus_codec",
+ "bus_spdif", "bus_pio", "bus_ths",
+ "bus_i2s0", "bus_i2s1", "bus_i2s2",
+ "bus_i2c0", "bus_i2c1", "bus_i2c2",
+ "bus_uart0", "bus_uart1",
+ "bus_uart2", "bus_uart3",
+ "bus_scr", "bus_ephy", "bus_dbg";
+ };
+
+ mmc0_clk: clk@01c20088 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20088 0x4>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+ clock-output-names = "mmc0",
+ "mmc0_output",
+ "mmc0_sample";
+ };
+
+ mmc1_clk: clk@01c2008c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c2008c 0x4>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+ clock-output-names = "mmc1",
+ "mmc1_output",
+ "mmc1_sample";
+ };
+
+ mmc2_clk: clk@01c20090 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20090 0x4>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+ clock-output-names = "mmc2",
+ "mmc2_output",
+ "mmc2_sample";
+ };
+
+ mbus_clk: clk@01c2015c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-a23-mbus-clk";
+ reg = <0x01c2015c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5>;
+ clock-output-names = "mbus";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun8i-h3-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bus_gates 6>;
+ resets = <&ahb_rst 6>;
+ #dma-cells = <1>;
+ };
+
+ mmc0: mmc@01c0f000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&bus_gates 8>,
+ <&mmc0_clk 0>,
+ <&mmc0_clk 1>,
+ <&mmc0_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb_rst 8>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@01c10000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&bus_gates 9>,
+ <&mmc1_clk 0>,
+ <&mmc1_clk 1>,
+ <&mmc1_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb_rst 9>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@01c11000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&bus_gates 10>,
+ <&mmc2_clk 0>,
+ <&mmc2_clk 1>,
+ <&mmc2_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb_rst 10>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pio: pinctrl@01c20800 {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bus_gates 69>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PA4", "PA5";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins_a: mmc0@0 {
+ allwinner,pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin@0 {
+ allwinner,pins = "PF6";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc1_pins_a: mmc1@0 {
+ allwinner,pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ ahb_rst: reset@01c202c0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-ahb1-reset";
+ reg = <0x01c202c0 0xc>;
+ };
+
+ apb1_rst: reset@01c202d0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d0 0x4>;
+ };
+
+ apb2_rst: reset@01c202d8 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d8 0x4>;
+ };
+
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ wdt0: watchdog@01c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ uart0: serial@01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 112>;
+ resets = <&apb2_rst 16>;
+ dmas = <&dma 6>, <&dma 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial@01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 113>;
+ resets = <&apb2_rst 17>;
+ dmas = <&dma 7>, <&dma 7>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial@01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 114>;
+ resets = <&apb2_rst 18>;
+ dmas = <&dma 8>, <&dma 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial@01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 115>;
+ resets = <&apb2_rst 19>;
+ dmas = <&dma 9>, <&dma 9>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ gic: interrupt-controller@01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x1000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ rtc: rtc@01f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+};
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: linux-arm-kernel
The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 497 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
new file mode 100644
index 0000000..1524130e
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -0,0 +1,497 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ pll1: clk at 01c20000 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-a23-pll1-clk";
+ reg = <0x01c20000 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll1";
+ };
+
+ /* dummy clock until actually implemented */
+ pll5: pll5_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <0>;
+ clock-output-names = "pll5";
+ };
+
+ pll6: clk at 01c20028 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun6i-a31-pll6-clk";
+ reg = <0x01c20028 0x4>;
+ clocks = <&osc24M>;
+ clock-output-names = "pll6", "pll6x2";
+ };
+
+ pll6d2: pll6d2_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clock-div = <2>;
+ clock-mult = <1>;
+ clocks = <&pll6 0>;
+ clock-output-names = "pll6d2";
+ };
+
+ /* dummy clock until pll6 can be reused */
+ pll8: pll8_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <1>;
+ clock-output-names = "pll8";
+ };
+
+ cpu: cpu_clk at 01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-cpu-clk";
+ reg = <0x01c20050 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+ clock-output-names = "cpu";
+ };
+
+ axi: axi_clk at 01c20050 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-axi-clk";
+ reg = <0x01c20050 0x4>;
+ clocks = <&cpu>;
+ clock-output-names = "axi";
+ };
+
+ ahb1: ahb1_clk at 01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun6i-a31-ahb1-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+ clock-output-names = "ahb1";
+ };
+
+ ahb2: ahb2_clk at 01c2005c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-h3-ahb2-clk";
+ reg = <0x01c2005c 0x4>;
+ clocks = <&ahb1>, <&pll6d2>;
+ clock-output-names = "ahb2";
+ };
+
+ apb1: apb1_clk at 01c20054 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb0-clk";
+ reg = <0x01c20054 0x4>;
+ clocks = <&ahb1>;
+ clock-output-names = "apb1";
+ };
+
+ apb2: apb2_clk at 01c20058 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-apb1-clk";
+ reg = <0x01c20058 0x4>;
+ clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
+ clock-output-names = "apb2";
+ };
+
+ bus_gates: clk at 01c20060 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun8i-h3-bus-gates-clk";
+ reg = <0x01c20060 0x14>;
+ clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
+ clock-names = "ahb1", "ahb2", "apb1", "apb2";
+ clock-indices = <5>, <6>, <8>,
+ <9>, <10>, <13>,
+ <14>, <17>, <18>,
+ <19>, <20>,
+ <21>, <23>,
+ <24>, <25>,
+ <26>, <27>,
+ <28>, <29>,
+ <30>, <31>, <32>,
+ <35>, <36>, <37>,
+ <40>, <41>, <43>,
+ <44>, <52>, <53>,
+ <54>, <64>,
+ <65>, <69>, <72>,
+ <76>, <77>, <78>,
+ <96>, <97>, <98>,
+ <112>, <113>,
+ <114>, <115>,
+ <116>, <128>, <135>;
+ clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
+ "bus_mmc1", "bus_mmc2", "bus_nand",
+ "bus_sdram", "bus_gmac", "bus_ts",
+ "bus_hstimer", "bus_spi0",
+ "bus_spi1", "bus_otg",
+ "bus_otg_ehci0", "bus_ehci1",
+ "bus_ehci2", "bus_ehci3",
+ "bus_otg_ohci0", "bus_ohci1",
+ "bus_ohci2", "bus_ohci3", "bus_ve",
+ "bus_lcd0", "bus_lcd1", "bus_deint",
+ "bus_csi", "bus_tve", "bus_hdmi",
+ "bus_de", "bus_gpu", "bus_msgbox",
+ "bus_spinlock", "bus_codec",
+ "bus_spdif", "bus_pio", "bus_ths",
+ "bus_i2s0", "bus_i2s1", "bus_i2s2",
+ "bus_i2c0", "bus_i2c1", "bus_i2c2",
+ "bus_uart0", "bus_uart1",
+ "bus_uart2", "bus_uart3",
+ "bus_scr", "bus_ephy", "bus_dbg";
+ };
+
+ mmc0_clk: clk at 01c20088 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20088 0x4>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+ clock-output-names = "mmc0",
+ "mmc0_output",
+ "mmc0_sample";
+ };
+
+ mmc1_clk: clk at 01c2008c {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c2008c 0x4>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+ clock-output-names = "mmc1",
+ "mmc1_output",
+ "mmc1_sample";
+ };
+
+ mmc2_clk: clk at 01c20090 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun4i-a10-mmc-clk";
+ reg = <0x01c20090 0x4>;
+ clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+ clock-output-names = "mmc2",
+ "mmc2_output",
+ "mmc2_sample";
+ };
+
+ mbus_clk: clk at 01c2015c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun8i-a23-mbus-clk";
+ reg = <0x01c2015c 0x4>;
+ clocks = <&osc24M>, <&pll6 1>, <&pll5>;
+ clock-output-names = "mbus";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dma: dma-controller at 01c02000 {
+ compatible = "allwinner,sun8i-h3-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bus_gates 6>;
+ resets = <&ahb_rst 6>;
+ #dma-cells = <1>;
+ };
+
+ mmc0: mmc at 01c0f000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&bus_gates 8>,
+ <&mmc0_clk 0>,
+ <&mmc0_clk 1>,
+ <&mmc0_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb_rst 8>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc at 01c10000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&bus_gates 9>,
+ <&mmc1_clk 0>,
+ <&mmc1_clk 1>,
+ <&mmc1_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb_rst 9>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc at 01c11000 {
+ compatible = "allwinner,sun5i-a13-mmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&bus_gates 10>,
+ <&mmc2_clk 0>,
+ <&mmc2_clk 1>,
+ <&mmc2_clk 2>;
+ clock-names = "ahb",
+ "mmc",
+ "output",
+ "sample";
+ resets = <&ahb_rst 10>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ pio: pinctrl at 01c20800 {
+ compatible = "allwinner,sun8i-h3-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&bus_gates 69>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ uart0_pins_a: uart0 at 0 {
+ allwinner,pins = "PA4", "PA5";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_pins_a: mmc0 at 0 {
+ allwinner,pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin at 0 {
+ allwinner,pins = "PF6";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc1_pins_a: mmc1 at 0 {
+ allwinner,pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ allwinner,function = "mmc1";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+ };
+
+ ahb_rst: reset at 01c202c0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-ahb1-reset";
+ reg = <0x01c202c0 0xc>;
+ };
+
+ apb1_rst: reset at 01c202d0 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d0 0x4>;
+ };
+
+ apb2_rst: reset at 01c202d8 {
+ #reset-cells = <1>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ reg = <0x01c202d8 0x4>;
+ };
+
+ timer at 01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ wdt0: watchdog at 01c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ uart0: serial at 01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 112>;
+ resets = <&apb2_rst 16>;
+ dmas = <&dma 6>, <&dma 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial at 01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 113>;
+ resets = <&apb2_rst 17>;
+ dmas = <&dma 7>, <&dma 7>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial at 01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 114>;
+ resets = <&apb2_rst 18>;
+ dmas = <&dma 8>, <&dma 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial at 01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&bus_gates 115>;
+ resets = <&apb2_rst 19>;
+ dmas = <&dma 9>, <&dma 9>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ gic: interrupt-controller at 01c81000 {
+ compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x1000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ rtc: rtc at 01f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+};
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 4/4] ARM: dts: sun8i: Add Orange Pi Plus support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij
Cc: Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, Jens Kuske, devicetree, linux-arm-kernel,
linux-kernel, linux-sunxi
The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 77 ++++++++++++++++++++++++++++
2 files changed, 79 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e8f44c7..cc7309b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -661,7 +661,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-ga10h-v1.1.dtb \
sun8i-a33-ippo-q8h-v1.2.dtb \
sun8i-a33-q8-tablet.dtb \
- sun8i-a33-sinlinx-sina33.dtb
+ sun8i-a33-sinlinx-sina33.dtb \
+ sun8i-h3-orangepi-plus.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
new file mode 100644
index 0000000..e67df59
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi Plus";
+ compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 4/4] ARM: dts: sun8i: Add Orange Pi Plus support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij
Cc: Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, Jens Kuske, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.
Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 77 ++++++++++++++++++++++++++++
2 files changed, 79 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e8f44c7..cc7309b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -661,7 +661,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-ga10h-v1.1.dtb \
sun8i-a33-ippo-q8h-v1.2.dtb \
sun8i-a33-q8-tablet.dtb \
- sun8i-a33-sinlinx-sina33.dtb
+ sun8i-a33-sinlinx-sina33.dtb \
+ sun8i-h3-orangepi-plus.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
new file mode 100644
index 0000000..e67df59
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi Plus";
+ compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* [PATCH v5 4/4] ARM: dts: sun8i: Add Orange Pi Plus support
@ 2015-12-04 21:24 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-04 21:24 UTC (permalink / raw)
To: linux-arm-kernel
The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts | 77 ++++++++++++++++++++++++++++
2 files changed, 79 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e8f44c7..cc7309b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -661,7 +661,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-ga10h-v1.1.dtb \
sun8i-a33-ippo-q8h-v1.2.dtb \
sun8i-a33-q8-tablet.dtb \
- sun8i-a33-sinlinx-sina33.dtb
+ sun8i-a33-sinlinx-sina33.dtb \
+ sun8i-h3-orangepi-plus.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
new file mode 100644
index 0000000..e67df59
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi Plus";
+ compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
--
2.6.3
^ permalink raw reply related [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/4] clk: sunxi: Add H3 clocks support
@ 2015-12-06 0:53 ` Rob Herring
0 siblings, 0 replies; 50+ messages in thread
From: Rob Herring @ 2015-12-06 0:53 UTC (permalink / raw)
To: Jens Kuske
Cc: Maxime Ripard, Chen-Yu Tsai, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
On Fri, Dec 04, 2015 at 10:24:40PM +0100, Jens Kuske wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
>
> It adds a new bus gates clock similar to the simple gates, but with a
> different parent clock for each single gate.
> Some of the gates use the new AHB2 clock as parent, whose clock source
> is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
> about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
> is mostly based on Allwinner kernel source code.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
> Documentation/devicetree/bindings/clock/sunxi.txt | 2 +
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
> drivers/clk/sunxi/Makefile | 1 +
> drivers/clk/sunxi/clk-sun8i-bus-gates.c | 112 ++++++++++++++++++++++
> drivers/clk/sunxi/clk-sunxi.c | 6 ++
> 4 files changed, 121 insertions(+)
> create mode 100644 drivers/clk/sunxi/clk-sun8i-bus-gates.c
>
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 153ac72..437962d 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -29,6 +29,7 @@ Required properties:
> "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
> "allwinner,sun9i-a80-cpus-clk" - for the CPUS on A80
> "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> + "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
> "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
> "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
> @@ -56,6 +57,7 @@ Required properties:
> "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
> "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
> + "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3
> "allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80
> "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
> "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
> index 103efab..abf4916 100644
> --- a/drivers/clk/sunxi/Makefile
> +++ b/drivers/clk/sunxi/Makefile
> @@ -10,6 +10,7 @@ obj-y += clk-a10-pll2.o
> obj-y += clk-a20-gmac.o
> obj-y += clk-mod0.o
> obj-y += clk-simple-gates.o
> +obj-y += clk-sun8i-bus-gates.o
> obj-y += clk-sun8i-mbus.o
> obj-y += clk-sun9i-core.o
> obj-y += clk-sun9i-mmc.o
> diff --git a/drivers/clk/sunxi/clk-sun8i-bus-gates.c b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
> new file mode 100644
> index 0000000..7ab60c5
> --- /dev/null
> +++ b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
> @@ -0,0 +1,112 @@
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * Based on clk-simple-gates.c, which is:
> + * Copyright 2015 Maxime Ripard
> + *
> + * Maxime Ripard <maxime.ripard@free-electrons.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +
> +static DEFINE_SPINLOCK(gates_lock);
> +
> +static void __init sun8i_h3_bus_gates_init(struct device_node *node)
> +{
> + static const char * const names[] = { "ahb1", "ahb2", "apb1", "apb2" };
> + enum { AHB1, AHB2, APB1, APB2, PARENT_MAX } clk_parent;
> + const char *parents[PARENT_MAX];
> + struct clk_onecell_data *clk_data;
> + const char *clk_name;
> + struct property *prop;
> + struct resource res;
> + void __iomem *clk_reg;
> + void __iomem *reg;
> + const __be32 *p;
> + int number, i;
> + u8 clk_bit;
> + u32 index;
> +
> + reg = of_io_request_and_map(node, 0, of_node_full_name(node));
> + if (IS_ERR(reg))
> + return;
> +
> + for (i = 0; i < ARRAY_SIZE(names); i++) {
> + index = of_property_match_string(node, "clock-names",
> + names[i]);
> + if (index < 0)
> + return;
> +
> + parents[i] = of_clk_get_parent_name(node, index);
> + }
> +
> + clk_data = kmalloc(sizeof(struct clk_onecell_data), GFP_KERNEL);
> + if (!clk_data)
> + goto err_unmap;
> +
> + number = of_property_count_u32_elems(node, "clock-indices");
> + of_property_read_u32_index(node, "clock-indices", number - 1, &number);
> +
> + clk_data->clks = kcalloc(number + 1, sizeof(struct clk *), GFP_KERNEL);
> + if (!clk_data->clks)
> + goto err_free_data;
> +
> + i = 0;
> + of_property_for_each_u32(node, "clock-indices", prop, p, index) {
> + of_property_read_string_index(node, "clock-output-names",
> + i, &clk_name);
> +
> + if (index == 17 || (index >= 29 && index <= 31))
> + clk_parent = AHB2;
> + else if (index <= 63 || index >= 128)
> + clk_parent = AHB1;
> + else if (index >= 64 && index <= 95)
> + clk_parent = APB1;
> + else if (index >= 96 && index <= 127)
> + clk_parent = APB2;
> +
> + clk_reg = reg + 4 * (index / 32);
> + clk_bit = index % 32;
> +
> + clk_data->clks[index] = clk_register_gate(NULL, clk_name,
> + parents[clk_parent],
> + 0, clk_reg, clk_bit,
> + 0, &gates_lock);
> + i++;
> +
> + if (IS_ERR(clk_data->clks[index])) {
> + WARN_ON(true);
> + continue;
> + }
> + }
> +
> + clk_data->clk_num = number + 1;
> + of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
> +
> + return;
> +
> +err_free_data:
> + kfree(clk_data);
> +err_unmap:
> + iounmap(reg);
> + of_address_to_resource(node, 0, &res);
> + release_mem_region(res.start, resource_size(&res));
> +}
> +
> +CLK_OF_DECLARE(sun8i_h3_bus_gates, "allwinner,sun8i-h3-bus-gates-clk",
> + sun8i_h3_bus_gates_init);
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 9c79af0c..5ba2188 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -778,6 +778,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
> .shift = 12,
> };
>
> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> + .shift = 0,
> +};
> +
> static void __init sunxi_mux_clk_setup(struct device_node *node,
> struct mux_data *data)
> {
> @@ -1130,6 +1134,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
> static const struct of_device_id clk_mux_match[] __initconst = {
> {.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
> {.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
> + {.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
> {}
> };
>
> @@ -1212,6 +1217,7 @@ CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
> CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
> CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
> CLK_OF_DECLARE(sun8i_a33_clk_init, "allwinner,sun8i-a33", sun6i_init_clocks);
> +CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
>
> static void __init sun9i_init_clocks(struct device_node *node)
> {
> --
> 2.6.3
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/4] clk: sunxi: Add H3 clocks support
@ 2015-12-06 0:53 ` Rob Herring
0 siblings, 0 replies; 50+ messages in thread
From: Rob Herring @ 2015-12-06 0:53 UTC (permalink / raw)
To: Jens Kuske
Cc: Maxime Ripard, Chen-Yu Tsai, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
On Fri, Dec 04, 2015 at 10:24:40PM +0100, Jens Kuske wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
>
> It adds a new bus gates clock similar to the simple gates, but with a
> different parent clock for each single gate.
> Some of the gates use the new AHB2 clock as parent, whose clock source
> is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
> about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
> is mostly based on Allwinner kernel source code.
>
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> Documentation/devicetree/bindings/clock/sunxi.txt | 2 +
For the binding:
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> drivers/clk/sunxi/Makefile | 1 +
> drivers/clk/sunxi/clk-sun8i-bus-gates.c | 112 ++++++++++++++++++++++
> drivers/clk/sunxi/clk-sunxi.c | 6 ++
> 4 files changed, 121 insertions(+)
> create mode 100644 drivers/clk/sunxi/clk-sun8i-bus-gates.c
>
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 153ac72..437962d 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -29,6 +29,7 @@ Required properties:
> "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
> "allwinner,sun9i-a80-cpus-clk" - for the CPUS on A80
> "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> + "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
> "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
> "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
> @@ -56,6 +57,7 @@ Required properties:
> "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
> "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
> + "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3
> "allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80
> "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
> "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
> index 103efab..abf4916 100644
> --- a/drivers/clk/sunxi/Makefile
> +++ b/drivers/clk/sunxi/Makefile
> @@ -10,6 +10,7 @@ obj-y += clk-a10-pll2.o
> obj-y += clk-a20-gmac.o
> obj-y += clk-mod0.o
> obj-y += clk-simple-gates.o
> +obj-y += clk-sun8i-bus-gates.o
> obj-y += clk-sun8i-mbus.o
> obj-y += clk-sun9i-core.o
> obj-y += clk-sun9i-mmc.o
> diff --git a/drivers/clk/sunxi/clk-sun8i-bus-gates.c b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
> new file mode 100644
> index 0000000..7ab60c5
> --- /dev/null
> +++ b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
> @@ -0,0 +1,112 @@
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> + *
> + * Based on clk-simple-gates.c, which is:
> + * Copyright 2015 Maxime Ripard
> + *
> + * Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +
> +static DEFINE_SPINLOCK(gates_lock);
> +
> +static void __init sun8i_h3_bus_gates_init(struct device_node *node)
> +{
> + static const char * const names[] = { "ahb1", "ahb2", "apb1", "apb2" };
> + enum { AHB1, AHB2, APB1, APB2, PARENT_MAX } clk_parent;
> + const char *parents[PARENT_MAX];
> + struct clk_onecell_data *clk_data;
> + const char *clk_name;
> + struct property *prop;
> + struct resource res;
> + void __iomem *clk_reg;
> + void __iomem *reg;
> + const __be32 *p;
> + int number, i;
> + u8 clk_bit;
> + u32 index;
> +
> + reg = of_io_request_and_map(node, 0, of_node_full_name(node));
> + if (IS_ERR(reg))
> + return;
> +
> + for (i = 0; i < ARRAY_SIZE(names); i++) {
> + index = of_property_match_string(node, "clock-names",
> + names[i]);
> + if (index < 0)
> + return;
> +
> + parents[i] = of_clk_get_parent_name(node, index);
> + }
> +
> + clk_data = kmalloc(sizeof(struct clk_onecell_data), GFP_KERNEL);
> + if (!clk_data)
> + goto err_unmap;
> +
> + number = of_property_count_u32_elems(node, "clock-indices");
> + of_property_read_u32_index(node, "clock-indices", number - 1, &number);
> +
> + clk_data->clks = kcalloc(number + 1, sizeof(struct clk *), GFP_KERNEL);
> + if (!clk_data->clks)
> + goto err_free_data;
> +
> + i = 0;
> + of_property_for_each_u32(node, "clock-indices", prop, p, index) {
> + of_property_read_string_index(node, "clock-output-names",
> + i, &clk_name);
> +
> + if (index == 17 || (index >= 29 && index <= 31))
> + clk_parent = AHB2;
> + else if (index <= 63 || index >= 128)
> + clk_parent = AHB1;
> + else if (index >= 64 && index <= 95)
> + clk_parent = APB1;
> + else if (index >= 96 && index <= 127)
> + clk_parent = APB2;
> +
> + clk_reg = reg + 4 * (index / 32);
> + clk_bit = index % 32;
> +
> + clk_data->clks[index] = clk_register_gate(NULL, clk_name,
> + parents[clk_parent],
> + 0, clk_reg, clk_bit,
> + 0, &gates_lock);
> + i++;
> +
> + if (IS_ERR(clk_data->clks[index])) {
> + WARN_ON(true);
> + continue;
> + }
> + }
> +
> + clk_data->clk_num = number + 1;
> + of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
> +
> + return;
> +
> +err_free_data:
> + kfree(clk_data);
> +err_unmap:
> + iounmap(reg);
> + of_address_to_resource(node, 0, &res);
> + release_mem_region(res.start, resource_size(&res));
> +}
> +
> +CLK_OF_DECLARE(sun8i_h3_bus_gates, "allwinner,sun8i-h3-bus-gates-clk",
> + sun8i_h3_bus_gates_init);
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 9c79af0c..5ba2188 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -778,6 +778,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
> .shift = 12,
> };
>
> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> + .shift = 0,
> +};
> +
> static void __init sunxi_mux_clk_setup(struct device_node *node,
> struct mux_data *data)
> {
> @@ -1130,6 +1134,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
> static const struct of_device_id clk_mux_match[] __initconst = {
> {.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
> {.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
> + {.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
> {}
> };
>
> @@ -1212,6 +1217,7 @@ CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
> CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
> CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
> CLK_OF_DECLARE(sun8i_a33_clk_init, "allwinner,sun8i-a33", sun6i_init_clocks);
> +CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
>
> static void __init sun9i_init_clocks(struct device_node *node)
> {
> --
> 2.6.3
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/4] clk: sunxi: Add H3 clocks support
@ 2015-12-06 0:53 ` Rob Herring
0 siblings, 0 replies; 50+ messages in thread
From: Rob Herring @ 2015-12-06 0:53 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Dec 04, 2015 at 10:24:40PM +0100, Jens Kuske wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
>
> It adds a new bus gates clock similar to the simple gates, but with a
> different parent clock for each single gate.
> Some of the gates use the new AHB2 clock as parent, whose clock source
> is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
> about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
> is mostly based on Allwinner kernel source code.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
> Documentation/devicetree/bindings/clock/sunxi.txt | 2 +
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
> drivers/clk/sunxi/Makefile | 1 +
> drivers/clk/sunxi/clk-sun8i-bus-gates.c | 112 ++++++++++++++++++++++
> drivers/clk/sunxi/clk-sunxi.c | 6 ++
> 4 files changed, 121 insertions(+)
> create mode 100644 drivers/clk/sunxi/clk-sun8i-bus-gates.c
>
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 153ac72..437962d 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -29,6 +29,7 @@ Required properties:
> "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31
> "allwinner,sun9i-a80-cpus-clk" - for the CPUS on A80
> "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31
> + "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3
> "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31
> "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23
> "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80
> @@ -56,6 +57,7 @@ Required properties:
> "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80
> "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
> "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23
> + "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3
> "allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80
> "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13
> "allwinner,sun4i-a10-mmc-clk" - for the MMC clock
> diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
> index 103efab..abf4916 100644
> --- a/drivers/clk/sunxi/Makefile
> +++ b/drivers/clk/sunxi/Makefile
> @@ -10,6 +10,7 @@ obj-y += clk-a10-pll2.o
> obj-y += clk-a20-gmac.o
> obj-y += clk-mod0.o
> obj-y += clk-simple-gates.o
> +obj-y += clk-sun8i-bus-gates.o
> obj-y += clk-sun8i-mbus.o
> obj-y += clk-sun9i-core.o
> obj-y += clk-sun9i-mmc.o
> diff --git a/drivers/clk/sunxi/clk-sun8i-bus-gates.c b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
> new file mode 100644
> index 0000000..7ab60c5
> --- /dev/null
> +++ b/drivers/clk/sunxi/clk-sun8i-bus-gates.c
> @@ -0,0 +1,112 @@
> +/*
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * Based on clk-simple-gates.c, which is:
> + * Copyright 2015 Maxime Ripard
> + *
> + * Maxime Ripard <maxime.ripard@free-electrons.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +
> +static DEFINE_SPINLOCK(gates_lock);
> +
> +static void __init sun8i_h3_bus_gates_init(struct device_node *node)
> +{
> + static const char * const names[] = { "ahb1", "ahb2", "apb1", "apb2" };
> + enum { AHB1, AHB2, APB1, APB2, PARENT_MAX } clk_parent;
> + const char *parents[PARENT_MAX];
> + struct clk_onecell_data *clk_data;
> + const char *clk_name;
> + struct property *prop;
> + struct resource res;
> + void __iomem *clk_reg;
> + void __iomem *reg;
> + const __be32 *p;
> + int number, i;
> + u8 clk_bit;
> + u32 index;
> +
> + reg = of_io_request_and_map(node, 0, of_node_full_name(node));
> + if (IS_ERR(reg))
> + return;
> +
> + for (i = 0; i < ARRAY_SIZE(names); i++) {
> + index = of_property_match_string(node, "clock-names",
> + names[i]);
> + if (index < 0)
> + return;
> +
> + parents[i] = of_clk_get_parent_name(node, index);
> + }
> +
> + clk_data = kmalloc(sizeof(struct clk_onecell_data), GFP_KERNEL);
> + if (!clk_data)
> + goto err_unmap;
> +
> + number = of_property_count_u32_elems(node, "clock-indices");
> + of_property_read_u32_index(node, "clock-indices", number - 1, &number);
> +
> + clk_data->clks = kcalloc(number + 1, sizeof(struct clk *), GFP_KERNEL);
> + if (!clk_data->clks)
> + goto err_free_data;
> +
> + i = 0;
> + of_property_for_each_u32(node, "clock-indices", prop, p, index) {
> + of_property_read_string_index(node, "clock-output-names",
> + i, &clk_name);
> +
> + if (index == 17 || (index >= 29 && index <= 31))
> + clk_parent = AHB2;
> + else if (index <= 63 || index >= 128)
> + clk_parent = AHB1;
> + else if (index >= 64 && index <= 95)
> + clk_parent = APB1;
> + else if (index >= 96 && index <= 127)
> + clk_parent = APB2;
> +
> + clk_reg = reg + 4 * (index / 32);
> + clk_bit = index % 32;
> +
> + clk_data->clks[index] = clk_register_gate(NULL, clk_name,
> + parents[clk_parent],
> + 0, clk_reg, clk_bit,
> + 0, &gates_lock);
> + i++;
> +
> + if (IS_ERR(clk_data->clks[index])) {
> + WARN_ON(true);
> + continue;
> + }
> + }
> +
> + clk_data->clk_num = number + 1;
> + of_clk_add_provider(node, of_clk_src_onecell_get, clk_data);
> +
> + return;
> +
> +err_free_data:
> + kfree(clk_data);
> +err_unmap:
> + iounmap(reg);
> + of_address_to_resource(node, 0, &res);
> + release_mem_region(res.start, resource_size(&res));
> +}
> +
> +CLK_OF_DECLARE(sun8i_h3_bus_gates, "allwinner,sun8i-h3-bus-gates-clk",
> + sun8i_h3_bus_gates_init);
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 9c79af0c..5ba2188 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -778,6 +778,10 @@ static const struct mux_data sun6i_a31_ahb1_mux_data __initconst = {
> .shift = 12,
> };
>
> +static const struct mux_data sun8i_h3_ahb2_mux_data __initconst = {
> + .shift = 0,
> +};
> +
> static void __init sunxi_mux_clk_setup(struct device_node *node,
> struct mux_data *data)
> {
> @@ -1130,6 +1134,7 @@ static const struct of_device_id clk_divs_match[] __initconst = {
> static const struct of_device_id clk_mux_match[] __initconst = {
> {.compatible = "allwinner,sun4i-a10-cpu-clk", .data = &sun4i_cpu_mux_data,},
> {.compatible = "allwinner,sun6i-a31-ahb1-mux-clk", .data = &sun6i_a31_ahb1_mux_data,},
> + {.compatible = "allwinner,sun8i-h3-ahb2-clk", .data = &sun8i_h3_ahb2_mux_data,},
> {}
> };
>
> @@ -1212,6 +1217,7 @@ CLK_OF_DECLARE(sun6i_a31_clk_init, "allwinner,sun6i-a31", sun6i_init_clocks);
> CLK_OF_DECLARE(sun6i_a31s_clk_init, "allwinner,sun6i-a31s", sun6i_init_clocks);
> CLK_OF_DECLARE(sun8i_a23_clk_init, "allwinner,sun8i-a23", sun6i_init_clocks);
> CLK_OF_DECLARE(sun8i_a33_clk_init, "allwinner,sun8i-a33", sun6i_init_clocks);
> +CLK_OF_DECLARE(sun8i_h3_clk_init, "allwinner,sun8i-h3", sun6i_init_clocks);
>
> static void __init sun9i_init_clocks(struct device_node *node)
> {
> --
> 2.6.3
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
2015-12-04 21:24 ` Jens Kuske
@ 2015-12-06 0:54 ` Rob Herring
-1 siblings, 0 replies; 50+ messages in thread
From: Rob Herring @ 2015-12-06 0:54 UTC (permalink / raw)
To: Jens Kuske
Cc: Maxime Ripard, Chen-Yu Tsai, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
On Fri, Dec 04, 2015 at 10:24:41PM +0100, Jens Kuske wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
> .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
> drivers/pinctrl/sunxi/Kconfig | 4 +
> drivers/pinctrl/sunxi/Makefile | 1 +
> drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c | 515 +++++++++++++++++++++
> 4 files changed, 521 insertions(+)
> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> index b321b26..e6ba602 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> @@ -18,6 +18,7 @@ Required properties:
> "allwinner,sun8i-a23-r-pinctrl"
> "allwinner,sun8i-a33-pinctrl"
> "allwinner,sun8i-a83t-pinctrl"
> + "allwinner,sun8i-h3-pinctrl"
>
> - reg: Should contain the register physical address and length for the
> pin controller.
> diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
> index e68fd95..89ab7f5 100644
> --- a/drivers/pinctrl/sunxi/Kconfig
> +++ b/drivers/pinctrl/sunxi/Kconfig
> @@ -51,6 +51,10 @@ config PINCTRL_SUN8I_A23_R
> depends on RESET_CONTROLLER
> select PINCTRL_SUNXI_COMMON
>
> +config PINCTRL_SUN8I_H3
> + def_bool MACH_SUN8I
> + select PINCTRL_SUNXI_COMMON
> +
> config PINCTRL_SUN9I_A80
> def_bool MACH_SUN9I
> select PINCTRL_SUNXI_COMMON
> diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
> index e080290..6bd818e 100644
> --- a/drivers/pinctrl/sunxi/Makefile
> +++ b/drivers/pinctrl/sunxi/Makefile
> @@ -13,4 +13,5 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23) += pinctrl-sun8i-a23.o
> obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o
> obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o
> obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
> +obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
> obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> new file mode 100644
> index 0000000..77d4cf0
> --- /dev/null
> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> @@ -0,0 +1,515 @@
> +/*
> + * Allwinner H3 SoCs pinctrl driver.
> + *
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * Based on pinctrl-sun8i-a23.c, which is:
> + * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
> + * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/pinctrl/pinctrl.h>
> +
> +#include "pinctrl-sunxi.h"
> +
> +static const struct sunxi_desc_pin sun8i_h3_pins[] = {
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart2"), /* TX */
> + SUNXI_FUNCTION(0x3, "jtag"), /* MS */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), /* PA_EINT0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart2"), /* RX */
> + SUNXI_FUNCTION(0x3, "jtag"), /* CK */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), /* PA_EINT1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
> + SUNXI_FUNCTION(0x3, "jtag"), /* DO */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), /* PA_EINT2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
> + SUNXI_FUNCTION(0x3, "jtag"), /* DI */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), /* PA_EINT3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart0"), /* TX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), /* PA_EINT4 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart0"), /* RX */
> + SUNXI_FUNCTION(0x3, "pwm0"),
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), /* PA_EINT5 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "sim"), /* PWREN */
> + SUNXI_FUNCTION(0x3, "pwm1"),
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), /* PA_EINT6 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "sim"), /* CLK */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), /* PA_EINT7 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "sim"), /* DATA */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), /* PA_EINT8 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "sim"), /* RST */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), /* PA_EINT9 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "sim"), /* DET */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), /* PA_EINT10 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
> + SUNXI_FUNCTION(0x3, "di"), /* TX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)), /* PA_EINT11 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
> + SUNXI_FUNCTION(0x3, "di"), /* RX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)), /* PA_EINT12 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "spi1"), /* CS */
> + SUNXI_FUNCTION(0x3, "uart3"), /* TX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)), /* PA_EINT13 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "spi1"), /* CLK */
> + SUNXI_FUNCTION(0x3, "uart3"), /* RX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)), /* PA_EINT14 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "spi1"), /* MOSI */
> + SUNXI_FUNCTION(0x3, "uart3"), /* RTS */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)), /* PA_EINT15 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "spi1"), /* MISO */
> + SUNXI_FUNCTION(0x3, "uart3"), /* CTS */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)), /* PA_EINT16 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "spdif"), /* OUT */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)), /* PA_EINT17 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s0"), /* SYNC */
> + SUNXI_FUNCTION(0x3, "i2c1"), /* SCK */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)), /* PA_EINT18 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s0"), /* CLK */
> + SUNXI_FUNCTION(0x3, "i2c1"), /* SDA */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)), /* PA_EINT19 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s0"), /* DOUT */
> + SUNXI_FUNCTION(0x3, "sim"), /* VPPEN */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)), /* PA_EINT20 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s0"), /* DIN */
> + SUNXI_FUNCTION(0x3, "sim"), /* VPPPP */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)), /* PA_EINT21 */
> + /* Hole */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* WE */
> + SUNXI_FUNCTION(0x3, "spi0")), /* MOSI */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
> + SUNXI_FUNCTION(0x3, "spi0")), /* MISO */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
> + SUNXI_FUNCTION(0x3, "spi0")), /* CLK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
> + SUNXI_FUNCTION(0x3, "spi0")), /* CS */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0")), /* CE0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* RE */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* CLK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* CMD */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0")), /* RB1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D4 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D5 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand"), /* DQ6 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D6 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand"), /* DQ7 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D7 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand"), /* DQS */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* RST */
> + /* Hole */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXCK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXCTL/RXDV */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXERR */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* CRS */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXCK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXCTL/TXEN */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXERR */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* CLKIN/COL */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* MDC */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* MDIO */
> + /* Hole */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* PCLK */
> + SUNXI_FUNCTION(0x3, "ts")), /* CLK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
> + SUNXI_FUNCTION(0x3, "ts")), /* ERR */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* HSYNC */
> + SUNXI_FUNCTION(0x3, "ts")), /* SYNC */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* VSYNC */
> + SUNXI_FUNCTION(0x3, "ts")), /* DVLD */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D0 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D1 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D2 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D3 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D4 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D4 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D5 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D5 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D6 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D6 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D7 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D7 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* SCK */
> + SUNXI_FUNCTION(0x3, "i2c2")), /* SCK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* SDA */
> + SUNXI_FUNCTION(0x3, "i2c2")), /* SDA */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out")),
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out")),
> + /* Hole */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
> + SUNXI_FUNCTION(0x3, "jtag")), /* MS */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
> + SUNXI_FUNCTION(0x3, "jtag")), /* DI */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
> + SUNXI_FUNCTION(0x3, "uart0")), /* TX */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
> + SUNXI_FUNCTION(0x3, "jtag")), /* DO */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
> + SUNXI_FUNCTION(0x3, "uart0")), /* RX */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
> + SUNXI_FUNCTION(0x3, "jtag")), /* CK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out")),
> + /* Hole */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), /* PG_EINT0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), /* PG_EINT1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), /* PG_EINT2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), /* PG_EINT3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), /* PG_EINT4 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), /* PG_EINT5 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* TX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), /* PG_EINT6 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* RX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)), /* PG_EINT7 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)), /* PG_EINT8 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)), /* PG_EINT9 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* SYNC */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)), /* PG_EINT10 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* CLK */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)), /* PG_EINT11 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* DOUT */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)), /* PG_EINT12 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* DIN */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)), /* PG_EINT13 */
> +};
> +
> +static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
> + .pins = sun8i_h3_pins,
> + .npins = ARRAY_SIZE(sun8i_h3_pins),
> + .irq_banks = 2,
> +};
> +
> +static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
> +{
> + return sunxi_pinctrl_init(pdev,
> + &sun8i_h3_pinctrl_data);
> +}
> +
> +static const struct of_device_id sun8i_h3_pinctrl_match[] = {
> + { .compatible = "allwinner,sun8i-h3-pinctrl", },
> + {}
> +};
> +
> +static struct platform_driver sun8i_h3_pinctrl_driver = {
> + .probe = sun8i_h3_pinctrl_probe,
> + .driver = {
> + .name = "sun8i-h3-pinctrl",
> + .of_match_table = sun8i_h3_pinctrl_match,
> + },
> +};
> +builtin_platform_driver(sun8i_h3_pinctrl_driver);
> --
> 2.6.3
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
@ 2015-12-06 0:54 ` Rob Herring
0 siblings, 0 replies; 50+ messages in thread
From: Rob Herring @ 2015-12-06 0:54 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Dec 04, 2015 at 10:24:41PM +0100, Jens Kuske wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
> .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt | 1 +
For the binding:
Acked-by: Rob Herring <robh@kernel.org>
> drivers/pinctrl/sunxi/Kconfig | 4 +
> drivers/pinctrl/sunxi/Makefile | 1 +
> drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c | 515 +++++++++++++++++++++
> 4 files changed, 521 insertions(+)
> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> index b321b26..e6ba602 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
> @@ -18,6 +18,7 @@ Required properties:
> "allwinner,sun8i-a23-r-pinctrl"
> "allwinner,sun8i-a33-pinctrl"
> "allwinner,sun8i-a83t-pinctrl"
> + "allwinner,sun8i-h3-pinctrl"
>
> - reg: Should contain the register physical address and length for the
> pin controller.
> diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
> index e68fd95..89ab7f5 100644
> --- a/drivers/pinctrl/sunxi/Kconfig
> +++ b/drivers/pinctrl/sunxi/Kconfig
> @@ -51,6 +51,10 @@ config PINCTRL_SUN8I_A23_R
> depends on RESET_CONTROLLER
> select PINCTRL_SUNXI_COMMON
>
> +config PINCTRL_SUN8I_H3
> + def_bool MACH_SUN8I
> + select PINCTRL_SUNXI_COMMON
> +
> config PINCTRL_SUN9I_A80
> def_bool MACH_SUN9I
> select PINCTRL_SUNXI_COMMON
> diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
> index e080290..6bd818e 100644
> --- a/drivers/pinctrl/sunxi/Makefile
> +++ b/drivers/pinctrl/sunxi/Makefile
> @@ -13,4 +13,5 @@ obj-$(CONFIG_PINCTRL_SUN8I_A23) += pinctrl-sun8i-a23.o
> obj-$(CONFIG_PINCTRL_SUN8I_A23_R) += pinctrl-sun8i-a23-r.o
> obj-$(CONFIG_PINCTRL_SUN8I_A33) += pinctrl-sun8i-a33.o
> obj-$(CONFIG_PINCTRL_SUN8I_A83T) += pinctrl-sun8i-a83t.o
> +obj-$(CONFIG_PINCTRL_SUN8I_H3) += pinctrl-sun8i-h3.o
> obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
> diff --git a/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> new file mode 100644
> index 0000000..77d4cf0
> --- /dev/null
> +++ b/drivers/pinctrl/sunxi/pinctrl-sun8i-h3.c
> @@ -0,0 +1,515 @@
> +/*
> + * Allwinner H3 SoCs pinctrl driver.
> + *
> + * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
> + *
> + * Based on pinctrl-sun8i-a23.c, which is:
> + * Copyright (C) 2014 Chen-Yu Tsai <wens@csie.org>
> + * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/pinctrl/pinctrl.h>
> +
> +#include "pinctrl-sunxi.h"
> +
> +static const struct sunxi_desc_pin sun8i_h3_pins[] = {
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart2"), /* TX */
> + SUNXI_FUNCTION(0x3, "jtag"), /* MS */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)), /* PA_EINT0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart2"), /* RX */
> + SUNXI_FUNCTION(0x3, "jtag"), /* CK */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)), /* PA_EINT1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
> + SUNXI_FUNCTION(0x3, "jtag"), /* DO */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)), /* PA_EINT2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
> + SUNXI_FUNCTION(0x3, "jtag"), /* DI */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)), /* PA_EINT3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart0"), /* TX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)), /* PA_EINT4 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart0"), /* RX */
> + SUNXI_FUNCTION(0x3, "pwm0"),
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)), /* PA_EINT5 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "sim"), /* PWREN */
> + SUNXI_FUNCTION(0x3, "pwm1"),
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)), /* PA_EINT6 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "sim"), /* CLK */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)), /* PA_EINT7 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "sim"), /* DATA */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)), /* PA_EINT8 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "sim"), /* RST */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)), /* PA_EINT9 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "sim"), /* DET */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 10)), /* PA_EINT10 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2c0"), /* SCK */
> + SUNXI_FUNCTION(0x3, "di"), /* TX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 11)), /* PA_EINT11 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2c0"), /* SDA */
> + SUNXI_FUNCTION(0x3, "di"), /* RX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 12)), /* PA_EINT12 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "spi1"), /* CS */
> + SUNXI_FUNCTION(0x3, "uart3"), /* TX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 13)), /* PA_EINT13 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 14),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "spi1"), /* CLK */
> + SUNXI_FUNCTION(0x3, "uart3"), /* RX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 14)), /* PA_EINT14 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 15),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "spi1"), /* MOSI */
> + SUNXI_FUNCTION(0x3, "uart3"), /* RTS */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 15)), /* PA_EINT15 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 16),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "spi1"), /* MISO */
> + SUNXI_FUNCTION(0x3, "uart3"), /* CTS */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 16)), /* PA_EINT16 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 17),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "spdif"), /* OUT */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 17)), /* PA_EINT17 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 18),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s0"), /* SYNC */
> + SUNXI_FUNCTION(0x3, "i2c1"), /* SCK */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 18)), /* PA_EINT18 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 19),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s0"), /* CLK */
> + SUNXI_FUNCTION(0x3, "i2c1"), /* SDA */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 19)), /* PA_EINT19 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 20),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s0"), /* DOUT */
> + SUNXI_FUNCTION(0x3, "sim"), /* VPPEN */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 20)), /* PA_EINT20 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 21),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s0"), /* DIN */
> + SUNXI_FUNCTION(0x3, "sim"), /* VPPPP */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 21)), /* PA_EINT21 */
> + /* Hole */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* WE */
> + SUNXI_FUNCTION(0x3, "spi0")), /* MOSI */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
> + SUNXI_FUNCTION(0x3, "spi0")), /* MISO */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
> + SUNXI_FUNCTION(0x3, "spi0")), /* CLK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
> + SUNXI_FUNCTION(0x3, "spi0")), /* CS */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0")), /* CE0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* RE */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* CLK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* CMD */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0")), /* RB1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D4 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D5 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand"), /* DQ6 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D6 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand"), /* DQ7 */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* D7 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "nand"), /* DQS */
> + SUNXI_FUNCTION(0x3, "mmc2")), /* RST */
> + /* Hole */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXD0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXCK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXCTL/RXDV */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* RXERR */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXD0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* CRS */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXCK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXCTL/TXEN */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* TXERR */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* CLKIN/COL */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* MDC */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac")), /* MDIO */
> + /* Hole */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* PCLK */
> + SUNXI_FUNCTION(0x3, "ts")), /* CLK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* MCLK */
> + SUNXI_FUNCTION(0x3, "ts")), /* ERR */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* HSYNC */
> + SUNXI_FUNCTION(0x3, "ts")), /* SYNC */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* VSYNC */
> + SUNXI_FUNCTION(0x3, "ts")), /* DVLD */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D0 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D1 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D2 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D3 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D4 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D4 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D5 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D5 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D6 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D6 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* D7 */
> + SUNXI_FUNCTION(0x3, "ts")), /* D7 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* SCK */
> + SUNXI_FUNCTION(0x3, "i2c2")), /* SCK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "csi"), /* SDA */
> + SUNXI_FUNCTION(0x3, "i2c2")), /* SDA */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out")),
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out")),
> + /* Hole */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
> + SUNXI_FUNCTION(0x3, "jtag")), /* MS */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
> + SUNXI_FUNCTION(0x3, "jtag")), /* DI */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
> + SUNXI_FUNCTION(0x3, "uart0")), /* TX */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
> + SUNXI_FUNCTION(0x3, "jtag")), /* DO */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
> + SUNXI_FUNCTION(0x3, "uart0")), /* RX */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
> + SUNXI_FUNCTION(0x3, "jtag")), /* CK */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out")),
> + /* Hole */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), /* PG_EINT0 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), /* PG_EINT1 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), /* PG_EINT2 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), /* PG_EINT3 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), /* PG_EINT4 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), /* PG_EINT5 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* TX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), /* PG_EINT6 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* RX */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)), /* PG_EINT7 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)), /* PG_EINT8 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)), /* PG_EINT9 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* SYNC */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)), /* PG_EINT10 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* CLK */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)), /* PG_EINT11 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* DOUT */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)), /* PG_EINT12 */
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "i2s1"), /* DIN */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)), /* PG_EINT13 */
> +};
> +
> +static const struct sunxi_pinctrl_desc sun8i_h3_pinctrl_data = {
> + .pins = sun8i_h3_pins,
> + .npins = ARRAY_SIZE(sun8i_h3_pins),
> + .irq_banks = 2,
> +};
> +
> +static int sun8i_h3_pinctrl_probe(struct platform_device *pdev)
> +{
> + return sunxi_pinctrl_init(pdev,
> + &sun8i_h3_pinctrl_data);
> +}
> +
> +static const struct of_device_id sun8i_h3_pinctrl_match[] = {
> + { .compatible = "allwinner,sun8i-h3-pinctrl", },
> + {}
> +};
> +
> +static struct platform_driver sun8i_h3_pinctrl_driver = {
> + .probe = sun8i_h3_pinctrl_probe,
> + .driver = {
> + .name = "sun8i-h3-pinctrl",
> + .of_match_table = sun8i_h3_pinctrl_match,
> + },
> +};
> +builtin_platform_driver(sun8i_h3_pinctrl_driver);
> --
> 2.6.3
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-07 8:12 ` Jean-Francois Moine
0 siblings, 0 replies; 50+ messages in thread
From: Jean-Francois Moine @ 2015-12-07 8:12 UTC (permalink / raw)
To: Jens Kuske
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij, devicetree, Vishnu Patekar,
Emilio López, Reinder de Haan, linux-kernel, Hans de Goede,
linux-sunxi, linux-arm-kernel
On Fri, 4 Dec 2015 22:24:42 +0100
Jens Kuske <jenskuske@gmail.com> wrote:
> The Allwinner H3 is a home entertainment system oriented SoC with
> four Cortex-A7 cores and a Mali-400MP2 GPU.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
> arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 497 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> new file mode 100644
> index 0000000..1524130e
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -0,0 +1,497 @@
[snip]
> + bus_gates: clk@01c20060 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-h3-bus-gates-clk";
> + reg = <0x01c20060 0x14>;
> + clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
> + clock-names = "ahb1", "ahb2", "apb1", "apb2";
> + clock-indices = <5>, <6>, <8>,
> + <9>, <10>, <13>,
> + <14>, <17>, <18>,
> + <19>, <20>,
> + <21>, <23>,
> + <24>, <25>,
> + <26>, <27>,
> + <28>, <29>,
> + <30>, <31>, <32>,
> + <35>, <36>, <37>,
> + <40>, <41>, <43>,
> + <44>, <52>, <53>,
> + <54>, <64>,
> + <65>, <69>, <72>,
> + <76>, <77>, <78>,
> + <96>, <97>, <98>,
> + <112>, <113>,
> + <114>, <115>,
> + <116>, <128>, <135>;
> + clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
> + "bus_mmc1", "bus_mmc2", "bus_nand",
> + "bus_sdram", "bus_gmac", "bus_ts",
> + "bus_hstimer", "bus_spi0",
> + "bus_spi1", "bus_otg",
> + "bus_otg_ehci0", "bus_ehci1",
> + "bus_ehci2", "bus_ehci3",
> + "bus_otg_ohci0", "bus_ohci1",
> + "bus_ohci2", "bus_ohci3", "bus_ve",
> + "bus_lcd0", "bus_lcd1", "bus_deint",
The tcon1 clock is used by both lcd0 and lcd1, while the tcon0 clock is used for TV output from lcd1, so, this should be:
"bus_tcon0", "bus_tcon1", "bus_deint",
(the tcon1 clock is used by both lcd0 and lcd1, while
the tcon0 clock is used for TV output from lcd1)
> + "bus_csi", "bus_tve", "bus_hdmi",
> + "bus_de", "bus_gpu", "bus_msgbox",
> + "bus_spinlock", "bus_codec",
> + "bus_spdif", "bus_pio", "bus_ths",
> + "bus_i2s0", "bus_i2s1", "bus_i2s2",
> + "bus_i2c0", "bus_i2c1", "bus_i2c2",
> + "bus_uart0", "bus_uart1",
> + "bus_uart2", "bus_uart3",
> + "bus_scr", "bus_ephy", "bus_dbg";
> + };
[snip]
--
Ken ar c'hentañ | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-07 8:12 ` Jean-Francois Moine
0 siblings, 0 replies; 50+ messages in thread
From: Jean-Francois Moine @ 2015-12-07 8:12 UTC (permalink / raw)
To: Jens Kuske
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij, devicetree-u79uwXL29TY76Z2rM5mHXA,
Vishnu Patekar, Emilio López, Reinder de Haan,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Hans de Goede,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Fri, 4 Dec 2015 22:24:42 +0100
Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> The Allwinner H3 is a home entertainment system oriented SoC with
> four Cortex-A7 cores and a Mali-400MP2 GPU.
>
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 497 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> new file mode 100644
> index 0000000..1524130e
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -0,0 +1,497 @@
[snip]
> + bus_gates: clk@01c20060 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-h3-bus-gates-clk";
> + reg = <0x01c20060 0x14>;
> + clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
> + clock-names = "ahb1", "ahb2", "apb1", "apb2";
> + clock-indices = <5>, <6>, <8>,
> + <9>, <10>, <13>,
> + <14>, <17>, <18>,
> + <19>, <20>,
> + <21>, <23>,
> + <24>, <25>,
> + <26>, <27>,
> + <28>, <29>,
> + <30>, <31>, <32>,
> + <35>, <36>, <37>,
> + <40>, <41>, <43>,
> + <44>, <52>, <53>,
> + <54>, <64>,
> + <65>, <69>, <72>,
> + <76>, <77>, <78>,
> + <96>, <97>, <98>,
> + <112>, <113>,
> + <114>, <115>,
> + <116>, <128>, <135>;
> + clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
> + "bus_mmc1", "bus_mmc2", "bus_nand",
> + "bus_sdram", "bus_gmac", "bus_ts",
> + "bus_hstimer", "bus_spi0",
> + "bus_spi1", "bus_otg",
> + "bus_otg_ehci0", "bus_ehci1",
> + "bus_ehci2", "bus_ehci3",
> + "bus_otg_ohci0", "bus_ohci1",
> + "bus_ohci2", "bus_ohci3", "bus_ve",
> + "bus_lcd0", "bus_lcd1", "bus_deint",
The tcon1 clock is used by both lcd0 and lcd1, while the tcon0 clock is used for TV output from lcd1, so, this should be:
"bus_tcon0", "bus_tcon1", "bus_deint",
(the tcon1 clock is used by both lcd0 and lcd1, while
the tcon0 clock is used for TV output from lcd1)
> + "bus_csi", "bus_tve", "bus_hdmi",
> + "bus_de", "bus_gpu", "bus_msgbox",
> + "bus_spinlock", "bus_codec",
> + "bus_spdif", "bus_pio", "bus_ths",
> + "bus_i2s0", "bus_i2s1", "bus_i2s2",
> + "bus_i2c0", "bus_i2c1", "bus_i2c2",
> + "bus_uart0", "bus_uart1",
> + "bus_uart2", "bus_uart3",
> + "bus_scr", "bus_ephy", "bus_dbg";
> + };
[snip]
--
Ken ar c'hentañ | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-07 8:12 ` Jean-Francois Moine
0 siblings, 0 replies; 50+ messages in thread
From: Jean-Francois Moine @ 2015-12-07 8:12 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, 4 Dec 2015 22:24:42 +0100
Jens Kuske <jenskuske@gmail.com> wrote:
> The Allwinner H3 is a home entertainment system oriented SoC with
> four Cortex-A7 cores and a Mali-400MP2 GPU.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
> ---
> arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 497 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
>
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> new file mode 100644
> index 0000000..1524130e
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -0,0 +1,497 @@
[snip]
> + bus_gates: clk at 01c20060 {
> + #clock-cells = <1>;
> + compatible = "allwinner,sun8i-h3-bus-gates-clk";
> + reg = <0x01c20060 0x14>;
> + clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
> + clock-names = "ahb1", "ahb2", "apb1", "apb2";
> + clock-indices = <5>, <6>, <8>,
> + <9>, <10>, <13>,
> + <14>, <17>, <18>,
> + <19>, <20>,
> + <21>, <23>,
> + <24>, <25>,
> + <26>, <27>,
> + <28>, <29>,
> + <30>, <31>, <32>,
> + <35>, <36>, <37>,
> + <40>, <41>, <43>,
> + <44>, <52>, <53>,
> + <54>, <64>,
> + <65>, <69>, <72>,
> + <76>, <77>, <78>,
> + <96>, <97>, <98>,
> + <112>, <113>,
> + <114>, <115>,
> + <116>, <128>, <135>;
> + clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
> + "bus_mmc1", "bus_mmc2", "bus_nand",
> + "bus_sdram", "bus_gmac", "bus_ts",
> + "bus_hstimer", "bus_spi0",
> + "bus_spi1", "bus_otg",
> + "bus_otg_ehci0", "bus_ehci1",
> + "bus_ehci2", "bus_ehci3",
> + "bus_otg_ohci0", "bus_ohci1",
> + "bus_ohci2", "bus_ohci3", "bus_ve",
> + "bus_lcd0", "bus_lcd1", "bus_deint",
The tcon1 clock is used by both lcd0 and lcd1, while the tcon0 clock is used for TV output from lcd1, so, this should be:
"bus_tcon0", "bus_tcon1", "bus_deint",
(the tcon1 clock is used by both lcd0 and lcd1, while
the tcon0 clock is used for TV output from lcd1)
> + "bus_csi", "bus_tve", "bus_hdmi",
> + "bus_de", "bus_gpu", "bus_msgbox",
> + "bus_spinlock", "bus_codec",
> + "bus_spdif", "bus_pio", "bus_ths",
> + "bus_i2s0", "bus_i2s1", "bus_i2s2",
> + "bus_i2c0", "bus_i2c1", "bus_i2c2",
> + "bus_uart0", "bus_uart1",
> + "bus_uart2", "bus_uart3",
> + "bus_scr", "bus_ephy", "bus_dbg";
> + };
[snip]
--
Ken ar c'henta? | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
@ 2015-12-07 9:23 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-07 9:23 UTC (permalink / raw)
To: Jens Kuske
Cc: Chen-Yu Tsai, Rob Herring, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 450 bytes --]
On Fri, Dec 04, 2015 at 10:24:41PM +0100, Jens Kuske wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
@ 2015-12-07 9:23 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-07 9:23 UTC (permalink / raw)
To: Jens Kuske
Cc: Chen-Yu Tsai, Rob Herring, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 495 bytes --]
On Fri, Dec 04, 2015 at 10:24:41PM +0100, Jens Kuske wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
>
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Acked-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
@ 2015-12-07 9:23 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-07 9:23 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Dec 04, 2015 at 10:24:41PM +0100, Jens Kuske wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151207/a2216d0a/attachment.sig>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-07 18:44 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-07 18:44 UTC (permalink / raw)
To: Jean-Francois Moine
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij, devicetree, Vishnu Patekar,
Emilio López, Reinder de Haan, linux-kernel, Hans de Goede,
linux-sunxi, linux-arm-kernel
On 07/12/15 09:12, Jean-Francois Moine wrote:
> On Fri, 4 Dec 2015 22:24:42 +0100
> Jens Kuske <jenskuske@gmail.com> wrote:
>
>> The Allwinner H3 is a home entertainment system oriented SoC with
>> four Cortex-A7 cores and a Mali-400MP2 GPU.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>> arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 497 insertions(+)
>> create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
>> new file mode 100644
>> index 0000000..1524130e
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
>> @@ -0,0 +1,497 @@
> [snip]
>> + bus_gates: clk@01c20060 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun8i-h3-bus-gates-clk";
>> + reg = <0x01c20060 0x14>;
>> + clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
>> + clock-names = "ahb1", "ahb2", "apb1", "apb2";
>> + clock-indices = <5>, <6>, <8>,
>> + <9>, <10>, <13>,
>> + <14>, <17>, <18>,
>> + <19>, <20>,
>> + <21>, <23>,
>> + <24>, <25>,
>> + <26>, <27>,
>> + <28>, <29>,
>> + <30>, <31>, <32>,
>> + <35>, <36>, <37>,
>> + <40>, <41>, <43>,
>> + <44>, <52>, <53>,
>> + <54>, <64>,
>> + <65>, <69>, <72>,
>> + <76>, <77>, <78>,
>> + <96>, <97>, <98>,
>> + <112>, <113>,
>> + <114>, <115>,
>> + <116>, <128>, <135>;
>> + clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
>> + "bus_mmc1", "bus_mmc2", "bus_nand",
>> + "bus_sdram", "bus_gmac", "bus_ts",
>> + "bus_hstimer", "bus_spi0",
>> + "bus_spi1", "bus_otg",
>> + "bus_otg_ehci0", "bus_ehci1",
>> + "bus_ehci2", "bus_ehci3",
>> + "bus_otg_ohci0", "bus_ohci1",
>> + "bus_ohci2", "bus_ohci3", "bus_ve",
>> + "bus_lcd0", "bus_lcd1", "bus_deint",
>
> The tcon1 clock is used by both lcd0 and lcd1, while the tcon0 clock is used for TV output from lcd1, so, this should be:
>
> "bus_tcon0", "bus_tcon1", "bus_deint",
>
> (the tcon1 clock is used by both lcd0 and lcd1, while
> the tcon0 clock is used for TV output from lcd1)
Hi,
These are only the ahb bus gates, not the module clocks.
Naming them lcd might be a bit confusing, but it follows the naming we
used since sun4i. And the tcon modules are still called lcd0 and lcd1
module in the manual too.
Interestingly there is only a tcon0 module clock in the manual and no
tcon1, but that is not part of this patch.
Jens
>
>> + "bus_csi", "bus_tve", "bus_hdmi",
>> + "bus_de", "bus_gpu", "bus_msgbox",
>> + "bus_spinlock", "bus_codec",
>> + "bus_spdif", "bus_pio", "bus_ths",
>> + "bus_i2s0", "bus_i2s1", "bus_i2s2",
>> + "bus_i2c0", "bus_i2c1", "bus_i2c2",
>> + "bus_uart0", "bus_uart1",
>> + "bus_uart2", "bus_uart3",
>> + "bus_scr", "bus_ephy", "bus_dbg";
>> + };
> [snip]
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-07 18:44 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-07 18:44 UTC (permalink / raw)
To: Jean-Francois Moine
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij, devicetree-u79uwXL29TY76Z2rM5mHXA,
Vishnu Patekar, Emilio López, Reinder de Haan,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Hans de Goede,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On 07/12/15 09:12, Jean-Francois Moine wrote:
> On Fri, 4 Dec 2015 22:24:42 +0100
> Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
>
>> The Allwinner H3 is a home entertainment system oriented SoC with
>> four Cortex-A7 cores and a Mali-400MP2 GPU.
>>
>> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>> arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 497 insertions(+)
>> create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
>> new file mode 100644
>> index 0000000..1524130e
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
>> @@ -0,0 +1,497 @@
> [snip]
>> + bus_gates: clk@01c20060 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun8i-h3-bus-gates-clk";
>> + reg = <0x01c20060 0x14>;
>> + clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
>> + clock-names = "ahb1", "ahb2", "apb1", "apb2";
>> + clock-indices = <5>, <6>, <8>,
>> + <9>, <10>, <13>,
>> + <14>, <17>, <18>,
>> + <19>, <20>,
>> + <21>, <23>,
>> + <24>, <25>,
>> + <26>, <27>,
>> + <28>, <29>,
>> + <30>, <31>, <32>,
>> + <35>, <36>, <37>,
>> + <40>, <41>, <43>,
>> + <44>, <52>, <53>,
>> + <54>, <64>,
>> + <65>, <69>, <72>,
>> + <76>, <77>, <78>,
>> + <96>, <97>, <98>,
>> + <112>, <113>,
>> + <114>, <115>,
>> + <116>, <128>, <135>;
>> + clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
>> + "bus_mmc1", "bus_mmc2", "bus_nand",
>> + "bus_sdram", "bus_gmac", "bus_ts",
>> + "bus_hstimer", "bus_spi0",
>> + "bus_spi1", "bus_otg",
>> + "bus_otg_ehci0", "bus_ehci1",
>> + "bus_ehci2", "bus_ehci3",
>> + "bus_otg_ohci0", "bus_ohci1",
>> + "bus_ohci2", "bus_ohci3", "bus_ve",
>> + "bus_lcd0", "bus_lcd1", "bus_deint",
>
> The tcon1 clock is used by both lcd0 and lcd1, while the tcon0 clock is used for TV output from lcd1, so, this should be:
>
> "bus_tcon0", "bus_tcon1", "bus_deint",
>
> (the tcon1 clock is used by both lcd0 and lcd1, while
> the tcon0 clock is used for TV output from lcd1)
Hi,
These are only the ahb bus gates, not the module clocks.
Naming them lcd might be a bit confusing, but it follows the naming we
used since sun4i. And the tcon modules are still called lcd0 and lcd1
module in the manual too.
Interestingly there is only a tcon0 module clock in the manual and no
tcon1, but that is not part of this patch.
Jens
>
>> + "bus_csi", "bus_tve", "bus_hdmi",
>> + "bus_de", "bus_gpu", "bus_msgbox",
>> + "bus_spinlock", "bus_codec",
>> + "bus_spdif", "bus_pio", "bus_ths",
>> + "bus_i2s0", "bus_i2s1", "bus_i2s2",
>> + "bus_i2c0", "bus_i2c1", "bus_i2c2",
>> + "bus_uart0", "bus_uart1",
>> + "bus_uart2", "bus_uart3",
>> + "bus_scr", "bus_ephy", "bus_dbg";
>> + };
> [snip]
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-07 18:44 ` Jens Kuske
0 siblings, 0 replies; 50+ messages in thread
From: Jens Kuske @ 2015-12-07 18:44 UTC (permalink / raw)
To: linux-arm-kernel
On 07/12/15 09:12, Jean-Francois Moine wrote:
> On Fri, 4 Dec 2015 22:24:42 +0100
> Jens Kuske <jenskuske@gmail.com> wrote:
>
>> The Allwinner H3 is a home entertainment system oriented SoC with
>> four Cortex-A7 cores and a Mali-400MP2 GPU.
>>
>> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
>> ---
>> arch/arm/boot/dts/sun8i-h3.dtsi | 497 ++++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 497 insertions(+)
>> create mode 100644 arch/arm/boot/dts/sun8i-h3.dtsi
>>
>> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
>> new file mode 100644
>> index 0000000..1524130e
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
>> @@ -0,0 +1,497 @@
> [snip]
>> + bus_gates: clk at 01c20060 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun8i-h3-bus-gates-clk";
>> + reg = <0x01c20060 0x14>;
>> + clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
>> + clock-names = "ahb1", "ahb2", "apb1", "apb2";
>> + clock-indices = <5>, <6>, <8>,
>> + <9>, <10>, <13>,
>> + <14>, <17>, <18>,
>> + <19>, <20>,
>> + <21>, <23>,
>> + <24>, <25>,
>> + <26>, <27>,
>> + <28>, <29>,
>> + <30>, <31>, <32>,
>> + <35>, <36>, <37>,
>> + <40>, <41>, <43>,
>> + <44>, <52>, <53>,
>> + <54>, <64>,
>> + <65>, <69>, <72>,
>> + <76>, <77>, <78>,
>> + <96>, <97>, <98>,
>> + <112>, <113>,
>> + <114>, <115>,
>> + <116>, <128>, <135>;
>> + clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
>> + "bus_mmc1", "bus_mmc2", "bus_nand",
>> + "bus_sdram", "bus_gmac", "bus_ts",
>> + "bus_hstimer", "bus_spi0",
>> + "bus_spi1", "bus_otg",
>> + "bus_otg_ehci0", "bus_ehci1",
>> + "bus_ehci2", "bus_ehci3",
>> + "bus_otg_ohci0", "bus_ohci1",
>> + "bus_ohci2", "bus_ohci3", "bus_ve",
>> + "bus_lcd0", "bus_lcd1", "bus_deint",
>
> The tcon1 clock is used by both lcd0 and lcd1, while the tcon0 clock is used for TV output from lcd1, so, this should be:
>
> "bus_tcon0", "bus_tcon1", "bus_deint",
>
> (the tcon1 clock is used by both lcd0 and lcd1, while
> the tcon0 clock is used for TV output from lcd1)
Hi,
These are only the ahb bus gates, not the module clocks.
Naming them lcd might be a bit confusing, but it follows the naming we
used since sun4i. And the tcon modules are still called lcd0 and lcd1
module in the manual too.
Interestingly there is only a tcon0 module clock in the manual and no
tcon1, but that is not part of this patch.
Jens
>
>> + "bus_csi", "bus_tve", "bus_hdmi",
>> + "bus_de", "bus_gpu", "bus_msgbox",
>> + "bus_spinlock", "bus_codec",
>> + "bus_spdif", "bus_pio", "bus_ths",
>> + "bus_i2s0", "bus_i2s1", "bus_i2s2",
>> + "bus_i2c0", "bus_i2c1", "bus_i2c2",
>> + "bus_uart0", "bus_uart1",
>> + "bus_uart2", "bus_uart3",
>> + "bus_scr", "bus_ephy", "bus_dbg";
>> + };
> [snip]
>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 8:06 ` Jean-Francois Moine
0 siblings, 0 replies; 50+ messages in thread
From: Jean-Francois Moine @ 2015-12-08 8:06 UTC (permalink / raw)
To: Jens Kuske
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij, devicetree, Vishnu Patekar,
Emilio López, Reinder de Haan, linux-kernel, Hans de Goede,
linux-sunxi, linux-arm-kernel
On Mon, 7 Dec 2015 19:44:30 +0100
Jens Kuske <jenskuske@gmail.com> wrote:
> >> + "bus_lcd0", "bus_lcd1", "bus_deint",
>
> > "bus_tcon0", "bus_tcon1", "bus_deint",
> >
> > (the tcon1 clock is used by both lcd0 and lcd1, while
> > the tcon0 clock is used for TV output from lcd1)
>
> Hi,
>
> These are only the ahb bus gates, not the module clocks.
> Naming them lcd might be a bit confusing, but it follows the naming we
> used since sun4i. And the tcon modules are still called lcd0 and lcd1
> module in the manual too.
There is no reference to TCON0 in the LCDs registers (H3 V1.1 pages 428
and 435), only TCON1.
> Interestingly there is only a tcon0 module clock in the manual and no
> tcon1, but that is not part of this patch.
Well, I looked again in the 3.4 kernel and, for the LCD0/HDMI, there is
no clock setting for TCON1: it just receives the AHB1 clock.
This means that its gate ("bus_lcd1" or "ahb1_tcon1") must be enabled
when streaming on LCD0 or LCD1.
The role of tcon0 is not yet clear to me, but it seems that its clock
is the streaming clock for LCD1/TV, as the HDMI clock is for LCD0/HDMI.
--
Ken ar c'hentañ | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 8:06 ` Jean-Francois Moine
0 siblings, 0 replies; 50+ messages in thread
From: Jean-Francois Moine @ 2015-12-08 8:06 UTC (permalink / raw)
To: Jens Kuske
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij, devicetree-u79uwXL29TY76Z2rM5mHXA,
Vishnu Patekar, Emilio López, Reinder de Haan,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Hans de Goede,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Mon, 7 Dec 2015 19:44:30 +0100
Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> >> + "bus_lcd0", "bus_lcd1", "bus_deint",
>
> > "bus_tcon0", "bus_tcon1", "bus_deint",
> >
> > (the tcon1 clock is used by both lcd0 and lcd1, while
> > the tcon0 clock is used for TV output from lcd1)
>
> Hi,
>
> These are only the ahb bus gates, not the module clocks.
> Naming them lcd might be a bit confusing, but it follows the naming we
> used since sun4i. And the tcon modules are still called lcd0 and lcd1
> module in the manual too.
There is no reference to TCON0 in the LCDs registers (H3 V1.1 pages 428
and 435), only TCON1.
> Interestingly there is only a tcon0 module clock in the manual and no
> tcon1, but that is not part of this patch.
Well, I looked again in the 3.4 kernel and, for the LCD0/HDMI, there is
no clock setting for TCON1: it just receives the AHB1 clock.
This means that its gate ("bus_lcd1" or "ahb1_tcon1") must be enabled
when streaming on LCD0 or LCD1.
The role of tcon0 is not yet clear to me, but it seems that its clock
is the streaming clock for LCD1/TV, as the HDMI clock is for LCD0/HDMI.
--
Ken ar c'hentañ | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 8:06 ` Jean-Francois Moine
0 siblings, 0 replies; 50+ messages in thread
From: Jean-Francois Moine @ 2015-12-08 8:06 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, 7 Dec 2015 19:44:30 +0100
Jens Kuske <jenskuske@gmail.com> wrote:
> >> + "bus_lcd0", "bus_lcd1", "bus_deint",
>
> > "bus_tcon0", "bus_tcon1", "bus_deint",
> >
> > (the tcon1 clock is used by both lcd0 and lcd1, while
> > the tcon0 clock is used for TV output from lcd1)
>
> Hi,
>
> These are only the ahb bus gates, not the module clocks.
> Naming them lcd might be a bit confusing, but it follows the naming we
> used since sun4i. And the tcon modules are still called lcd0 and lcd1
> module in the manual too.
There is no reference to TCON0 in the LCDs registers (H3 V1.1 pages 428
and 435), only TCON1.
> Interestingly there is only a tcon0 module clock in the manual and no
> tcon1, but that is not part of this patch.
Well, I looked again in the 3.4 kernel and, for the LCD0/HDMI, there is
no clock setting for TCON1: it just receives the AHB1 clock.
This means that its gate ("bus_lcd1" or "ahb1_tcon1") must be enabled
when streaming on LCD0 or LCD1.
The role of tcon0 is not yet clear to me, but it seems that its clock
is the streaming clock for LCD1/TV, as the HDMI clock is for LCD0/HDMI.
--
Ken ar c'henta? | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/4] clk: sunxi: Add H3 clocks support
@ 2015-12-08 8:11 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:11 UTC (permalink / raw)
To: Jens Kuske
Cc: Chen-Yu Tsai, Rob Herring, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 774 bytes --]
Hi Jens,
On Fri, Dec 04, 2015 at 10:24:40PM +0100, Jens Kuske wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
>
> It adds a new bus gates clock similar to the simple gates, but with a
> different parent clock for each single gate.
> Some of the gates use the new AHB2 clock as parent, whose clock source
> is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
> about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
> is mostly based on Allwinner kernel source code.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 1/4] clk: sunxi: Add H3 clocks support
@ 2015-12-08 8:11 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:11 UTC (permalink / raw)
To: Jens Kuske
Cc: Chen-Yu Tsai, Rob Herring, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 780 bytes --]
Hi Jens,
On Fri, Dec 04, 2015 at 10:24:40PM +0100, Jens Kuske wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
>
> It adds a new bus gates clock similar to the simple gates, but with a
> different parent clock for each single gate.
> Some of the gates use the new AHB2 clock as parent, whose clock source
> is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
> about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
> is mostly based on Allwinner kernel source code.
>
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 1/4] clk: sunxi: Add H3 clocks support
@ 2015-12-08 8:11 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:11 UTC (permalink / raw)
To: linux-arm-kernel
Hi Jens,
On Fri, Dec 04, 2015 at 10:24:40PM +0100, Jens Kuske wrote:
> The H3 clock control unit is similar to the those of other sun8i family
> members like the A23.
>
> It adds a new bus gates clock similar to the simple gates, but with a
> different parent clock for each single gate.
> Some of the gates use the new AHB2 clock as parent, whose clock source
> is muxable between AHB1 and PLL6/2. The documentation isn't totally clear
> about which devices belong to AHB2 now, especially USB EHIC/OHIC, so it
> is mostly based on Allwinner kernel source code.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151208/ad73f984/attachment.sig>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 8:28 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:28 UTC (permalink / raw)
To: Jens Kuske
Cc: Chen-Yu Tsai, Rob Herring, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 373 bytes --]
On Fri, Dec 04, 2015 at 10:24:42PM +0100, Jens Kuske wrote:
> The Allwinner H3 is a home entertainment system oriented SoC with
> four Cortex-A7 cores and a Mali-400MP2 GPU.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 8:28 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:28 UTC (permalink / raw)
To: Jens Kuske
Cc: Chen-Yu Tsai, Rob Herring, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 389 bytes --]
On Fri, Dec 04, 2015 at 10:24:42PM +0100, Jens Kuske wrote:
> The Allwinner H3 is a home entertainment system oriented SoC with
> four Cortex-A7 cores and a Mali-400MP2 GPU.
>
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 8:28 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:28 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Dec 04, 2015 at 10:24:42PM +0100, Jens Kuske wrote:
> The Allwinner H3 is a home entertainment system oriented SoC with
> four Cortex-A7 cores and a Mali-400MP2 GPU.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151208/3e4be78b/attachment.sig>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 8:32 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:32 UTC (permalink / raw)
To: Jean-Francois Moine
Cc: Jens Kuske, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij, devicetree, Vishnu Patekar,
Emilio López, Reinder de Haan, linux-kernel, Hans de Goede,
linux-sunxi, linux-arm-kernel
[-- Attachment #1: Type: text/plain, Size: 1898 bytes --]
On Tue, Dec 08, 2015 at 09:06:58AM +0100, Jean-Francois Moine wrote:
> On Mon, 7 Dec 2015 19:44:30 +0100
> Jens Kuske <jenskuske@gmail.com> wrote:
>
> > >> + "bus_lcd0", "bus_lcd1", "bus_deint",
> >
> > > "bus_tcon0", "bus_tcon1", "bus_deint",
> > >
> > > (the tcon1 clock is used by both lcd0 and lcd1, while
> > > the tcon0 clock is used for TV output from lcd1)
> >
> > Hi,
> >
> > These are only the ahb bus gates, not the module clocks.
> > Naming them lcd might be a bit confusing, but it follows the naming we
> > used since sun4i. And the tcon modules are still called lcd0 and lcd1
> > module in the manual too.
>
> There is no reference to TCON0 in the LCDs registers (H3 V1.1 pages 428
> and 435), only TCON1.
>
> > Interestingly there is only a tcon0 module clock in the manual and no
> > tcon1, but that is not part of this patch.
>
> Well, I looked again in the 3.4 kernel and, for the LCD0/HDMI, there is
> no clock setting for TCON1: it just receives the AHB1 clock.
>
> This means that its gate ("bus_lcd1" or "ahb1_tcon1") must be enabled
> when streaming on LCD0 or LCD1.
>
> The role of tcon0 is not yet clear to me, but it seems that its clock
> is the streaming clock for LCD1/TV, as the HDMI clock is for LCD0/HDMI.
If the H3 display block is done the same way than the A10 (and later)
one on this aspect, then the TCON has two channels with two different
streaming (or functional, you pick the name) clocks. The channel 0 is
usually used for RGB, the channel 1 for HDMI, composite and VGA.
Maybe they just added different bus gates for those two different
channels, and moved HDMI to the channel 0.
Anyway, that can always be changed later on if we have more clue on
what's going on.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 8:32 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:32 UTC (permalink / raw)
To: Jean-Francois Moine
Cc: Jens Kuske, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij, devicetree-u79uwXL29TY76Z2rM5mHXA,
Vishnu Patekar, Emilio López, Reinder de Haan,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Hans de Goede,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
[-- Attachment #1: Type: text/plain, Size: 1877 bytes --]
On Tue, Dec 08, 2015 at 09:06:58AM +0100, Jean-Francois Moine wrote:
> On Mon, 7 Dec 2015 19:44:30 +0100
> Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
>
> > >> + "bus_lcd0", "bus_lcd1", "bus_deint",
> >
> > > "bus_tcon0", "bus_tcon1", "bus_deint",
> > >
> > > (the tcon1 clock is used by both lcd0 and lcd1, while
> > > the tcon0 clock is used for TV output from lcd1)
> >
> > Hi,
> >
> > These are only the ahb bus gates, not the module clocks.
> > Naming them lcd might be a bit confusing, but it follows the naming we
> > used since sun4i. And the tcon modules are still called lcd0 and lcd1
> > module in the manual too.
>
> There is no reference to TCON0 in the LCDs registers (H3 V1.1 pages 428
> and 435), only TCON1.
>
> > Interestingly there is only a tcon0 module clock in the manual and no
> > tcon1, but that is not part of this patch.
>
> Well, I looked again in the 3.4 kernel and, for the LCD0/HDMI, there is
> no clock setting for TCON1: it just receives the AHB1 clock.
>
> This means that its gate ("bus_lcd1" or "ahb1_tcon1") must be enabled
> when streaming on LCD0 or LCD1.
>
> The role of tcon0 is not yet clear to me, but it seems that its clock
> is the streaming clock for LCD1/TV, as the HDMI clock is for LCD0/HDMI.
If the H3 display block is done the same way than the A10 (and later)
one on this aspect, then the TCON has two channels with two different
streaming (or functional, you pick the name) clocks. The channel 0 is
usually used for RGB, the channel 1 for HDMI, composite and VGA.
Maybe they just added different bus gates for those two different
channels, and moved HDMI to the channel 0.
Anyway, that can always be changed later on if we have more clue on
what's going on.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 8:32 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:32 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Dec 08, 2015 at 09:06:58AM +0100, Jean-Francois Moine wrote:
> On Mon, 7 Dec 2015 19:44:30 +0100
> Jens Kuske <jenskuske@gmail.com> wrote:
>
> > >> + "bus_lcd0", "bus_lcd1", "bus_deint",
> >
> > > "bus_tcon0", "bus_tcon1", "bus_deint",
> > >
> > > (the tcon1 clock is used by both lcd0 and lcd1, while
> > > the tcon0 clock is used for TV output from lcd1)
> >
> > Hi,
> >
> > These are only the ahb bus gates, not the module clocks.
> > Naming them lcd might be a bit confusing, but it follows the naming we
> > used since sun4i. And the tcon modules are still called lcd0 and lcd1
> > module in the manual too.
>
> There is no reference to TCON0 in the LCDs registers (H3 V1.1 pages 428
> and 435), only TCON1.
>
> > Interestingly there is only a tcon0 module clock in the manual and no
> > tcon1, but that is not part of this patch.
>
> Well, I looked again in the 3.4 kernel and, for the LCD0/HDMI, there is
> no clock setting for TCON1: it just receives the AHB1 clock.
>
> This means that its gate ("bus_lcd1" or "ahb1_tcon1") must be enabled
> when streaming on LCD0 or LCD1.
>
> The role of tcon0 is not yet clear to me, but it seems that its clock
> is the streaming clock for LCD1/TV, as the HDMI clock is for LCD0/HDMI.
If the H3 display block is done the same way than the A10 (and later)
one on this aspect, then the TCON has two channels with two different
streaming (or functional, you pick the name) clocks. The channel 0 is
usually used for RGB, the channel 1 for HDMI, composite and VGA.
Maybe they just added different bus gates for those two different
channels, and moved HDMI to the channel 0.
Anyway, that can always be changed later on if we have more clue on
what's going on.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151208/4c688f3d/attachment.sig>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 4/4] ARM: dts: sun8i: Add Orange Pi Plus support
@ 2015-12-08 8:33 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:33 UTC (permalink / raw)
To: Jens Kuske
Cc: Chen-Yu Tsai, Rob Herring, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
[-- Attachment #1: Type: text/plain, Size: 561 bytes --]
On Fri, Dec 04, 2015 at 10:24:43PM +0100, Jens Kuske wrote:
> The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
> with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
> a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
> WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
> and a 40-pin GPIO header.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 4/4] ARM: dts: sun8i: Add Orange Pi Plus support
@ 2015-12-08 8:33 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:33 UTC (permalink / raw)
To: Jens Kuske
Cc: Chen-Yu Tsai, Rob Herring, Michael Turquette, Stephen Boyd,
Linus Walleij, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 574 bytes --]
On Fri, Dec 04, 2015 at 10:24:43PM +0100, Jens Kuske wrote:
> The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
> with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
> a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
> WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
> and a 40-pin GPIO header.
>
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 4/4] ARM: dts: sun8i: Add Orange Pi Plus support
@ 2015-12-08 8:33 ` Maxime Ripard
0 siblings, 0 replies; 50+ messages in thread
From: Maxime Ripard @ 2015-12-08 8:33 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Dec 04, 2015 at 10:24:43PM +0100, Jens Kuske wrote:
> The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
> with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
> a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
> WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
> and a 40-pin GPIO header.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20151208/a767ac58/attachment.sig>
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
2015-12-08 8:32 ` Maxime Ripard
(?)
@ 2015-12-08 9:19 ` Jean-Francois Moine
-1 siblings, 0 replies; 50+ messages in thread
From: Jean-Francois Moine @ 2015-12-08 9:19 UTC (permalink / raw)
To: Maxime Ripard
Cc: Jens Kuske, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij, devicetree, Vishnu Patekar,
Emilio López, Reinder de Haan, linux-kernel, Hans de Goede,
linux-sunxi, linux-arm-kernel
On Tue, 8 Dec 2015 09:32:24 +0100
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> If the H3 display block is done the same way than the A10 (and later)
> one on this aspect, then the TCON has two channels with two different
> streaming (or functional, you pick the name) clocks. The channel 0 is
> usually used for RGB, the channel 1 for HDMI, composite and VGA.
>
> Maybe they just added different bus gates for those two different
> channels, and moved HDMI to the channel 0.
>
> Anyway, that can always be changed later on if we have more clue on
> what's going on.
I don't know about the other Allwinner chips, and your DRM driver for
these ones cannot be reused for the H3 because its display engine
(DE.2) is completely different.
The DE2 runs at 432MHz and treats both LCDs. The TCON1 runs at a fixed
rate, 200MHz, and the streaming rates are defined by the HDMI (LCD0) and
TCON0 (LCD1) clocks.
BTW, I hope to submit a H3 DRM driver before new year.
--
Ken ar c'hentañ | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 9:19 ` Jean-Francois Moine
0 siblings, 0 replies; 50+ messages in thread
From: Jean-Francois Moine @ 2015-12-08 9:19 UTC (permalink / raw)
To: Maxime Ripard
Cc: Jens Kuske, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Linus Walleij, devicetree-u79uwXL29TY76Z2rM5mHXA,
Vishnu Patekar, Emilio López, Reinder de Haan,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Hans de Goede,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Tue, 8 Dec 2015 09:32:24 +0100
Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> If the H3 display block is done the same way than the A10 (and later)
> one on this aspect, then the TCON has two channels with two different
> streaming (or functional, you pick the name) clocks. The channel 0 is
> usually used for RGB, the channel 1 for HDMI, composite and VGA.
>
> Maybe they just added different bus gates for those two different
> channels, and moved HDMI to the channel 0.
>
> Anyway, that can always be changed later on if we have more clue on
> what's going on.
I don't know about the other Allwinner chips, and your DRM driver for
these ones cannot be reused for the H3 because its display engine
(DE.2) is completely different.
The DE2 runs at 432MHz and treats both LCDs. The TCON1 runs at a fixed
rate, 200MHz, and the streaming rates are defined by the HDMI (LCD0) and
TCON0 (LCD1) clocks.
BTW, I hope to submit a H3 DRM driver before new year.
--
Ken ar c'hentañ | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI
@ 2015-12-08 9:19 ` Jean-Francois Moine
0 siblings, 0 replies; 50+ messages in thread
From: Jean-Francois Moine @ 2015-12-08 9:19 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, 8 Dec 2015 09:32:24 +0100
Maxime Ripard <maxime.ripard@free-electrons.com> wrote:
> If the H3 display block is done the same way than the A10 (and later)
> one on this aspect, then the TCON has two channels with two different
> streaming (or functional, you pick the name) clocks. The channel 0 is
> usually used for RGB, the channel 1 for HDMI, composite and VGA.
>
> Maybe they just added different bus gates for those two different
> channels, and moved HDMI to the channel 0.
>
> Anyway, that can always be changed later on if we have more clue on
> what's going on.
I don't know about the other Allwinner chips, and your DRM driver for
these ones cannot be reused for the H3 because its display engine
(DE.2) is completely different.
The DE2 runs at 432MHz and treats both LCDs. The TCON1 runs at a fixed
rate, 200MHz, and the streaming rates are defined by the HDMI (LCD0) and
TCON0 (LCD1) clocks.
BTW, I hope to submit a H3 DRM driver before new year.
--
Ken ar c'henta? | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
@ 2015-12-11 9:15 ` Linus Walleij
0 siblings, 0 replies; 50+ messages in thread
From: Linus Walleij @ 2015-12-11 9:15 UTC (permalink / raw)
To: Jens Kuske
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree, linux-arm-kernel, linux-kernel,
linux-sunxi
On Fri, Dec 4, 2015 at 10:24 PM, Jens Kuske <jenskuske@gmail.com> wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Patch applied with Rob's & Maxime's ACKs.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
@ 2015-12-11 9:15 ` Linus Walleij
0 siblings, 0 replies; 50+ messages in thread
From: Linus Walleij @ 2015-12-11 9:15 UTC (permalink / raw)
To: Jens Kuske
Cc: Maxime Ripard, Chen-Yu Tsai, Rob Herring, Michael Turquette,
Stephen Boyd, Hans de Goede, Reinder de Haan, Vishnu Patekar,
Emilio López, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, linux-sunxi
On Fri, Dec 4, 2015 at 10:24 PM, Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
>
> Signed-off-by: Jens Kuske <jenskuske-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Patch applied with Rob's & Maxime's ACKs.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support
@ 2015-12-11 9:15 ` Linus Walleij
0 siblings, 0 replies; 50+ messages in thread
From: Linus Walleij @ 2015-12-11 9:15 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Dec 4, 2015 at 10:24 PM, Jens Kuske <jenskuske@gmail.com> wrote:
> The H3 uses the same pin controller as previous SoC's from Allwinner.
> Add support for the pins controlled by the main PIO controller.
>
> Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Patch applied with Rob's & Maxime's ACKs.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 50+ messages in thread
end of thread, other threads:[~2015-12-11 9:15 UTC | newest]
Thread overview: 50+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2015-12-04 21:24 [PATCH v5 0/4] ARM: sunxi: Allwinner H3 support Jens Kuske
2015-12-04 21:24 ` Jens Kuske
2015-12-04 21:24 ` Jens Kuske
2015-12-04 21:24 ` [PATCH v5 1/4] clk: sunxi: Add H3 clocks support Jens Kuske
2015-12-04 21:24 ` Jens Kuske
2015-12-04 21:24 ` Jens Kuske
2015-12-06 0:53 ` Rob Herring
2015-12-06 0:53 ` Rob Herring
2015-12-06 0:53 ` Rob Herring
2015-12-08 8:11 ` Maxime Ripard
2015-12-08 8:11 ` Maxime Ripard
2015-12-08 8:11 ` Maxime Ripard
2015-12-04 21:24 ` [PATCH v5 2/4] pinctrl: sunxi: Add H3 PIO controller support Jens Kuske
2015-12-04 21:24 ` Jens Kuske
2015-12-04 21:24 ` Jens Kuske
2015-12-06 0:54 ` Rob Herring
2015-12-06 0:54 ` Rob Herring
2015-12-07 9:23 ` Maxime Ripard
2015-12-07 9:23 ` Maxime Ripard
2015-12-07 9:23 ` Maxime Ripard
2015-12-11 9:15 ` Linus Walleij
2015-12-11 9:15 ` Linus Walleij
2015-12-11 9:15 ` Linus Walleij
2015-12-04 21:24 ` [PATCH v5 3/4] ARM: dts: sunxi: Add Allwinner H3 DTSI Jens Kuske
2015-12-04 21:24 ` Jens Kuske
2015-12-04 21:24 ` Jens Kuske
2015-12-07 8:12 ` Jean-Francois Moine
2015-12-07 8:12 ` Jean-Francois Moine
2015-12-07 8:12 ` Jean-Francois Moine
2015-12-07 18:44 ` Jens Kuske
2015-12-07 18:44 ` Jens Kuske
2015-12-07 18:44 ` Jens Kuske
2015-12-08 8:06 ` Jean-Francois Moine
2015-12-08 8:06 ` Jean-Francois Moine
2015-12-08 8:06 ` Jean-Francois Moine
2015-12-08 8:32 ` Maxime Ripard
2015-12-08 8:32 ` Maxime Ripard
2015-12-08 8:32 ` Maxime Ripard
2015-12-08 9:19 ` Jean-Francois Moine
2015-12-08 9:19 ` Jean-Francois Moine
2015-12-08 9:19 ` Jean-Francois Moine
2015-12-08 8:28 ` Maxime Ripard
2015-12-08 8:28 ` Maxime Ripard
2015-12-08 8:28 ` Maxime Ripard
2015-12-04 21:24 ` [PATCH v5 4/4] ARM: dts: sun8i: Add Orange Pi Plus support Jens Kuske
2015-12-04 21:24 ` Jens Kuske
2015-12-04 21:24 ` Jens Kuske
2015-12-08 8:33 ` Maxime Ripard
2015-12-08 8:33 ` Maxime Ripard
2015-12-08 8:33 ` Maxime Ripard
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.