[PATCH v4 1/3] dt-binding: power: Add otg regulator binding

[PATCH v4 1/3] dt-binding: power: Add otg regulator binding

[Tim Bird]

Add a binding for the regulator which controls the OTG chargepath switch.
The OTG switch gets its power from pm8941_5vs1, and that should be
expressed as a usb_otg_in-supply property in the DT node for the
charger driver.  The regulator name is "otg-vbus".

Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
---
Changes since v3
 - switch supply name to have underscores instead of dashes
   - (switched back to match the name used in data sheets)
 - switch regulator node name to otg-vbus
Changes since v1
 - switch supply name to have dashes instead of underscores
 - remove superfluous DT explanations in the otg node description
---
 .../devicetree/bindings/power_supply/qcom_smbb.txt    | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
index 65b88fa..06f8a5d 100644
--- a/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
+++ b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
@@ -105,6 +105,22 @@ PROPERTIES
                regulation must be done externally to fully comply with
                the JEITA safety guidelines if this flag is set.
 
+- usb_otg_in-supply:
+  Usage: optional
+  Value type: <phandle>
+  Description: Reference to the regulator supplying power to the USB_OTG_IN
+               pin.
+
+child nodes:
+- otg-vbus:
+  Usage: optional
+  Description: This node defines a regulator used to control the direction
+               of VBUS voltage - specifically: whether to supply voltage
+               to VBUS for host mode operation of the OTG port, or allow
+               input voltage from external VBUS for charging.  In the
+               hardware, the supply for this regulator comes from
+               usb_otg_in-supply.
+
 EXAMPLE
 charger@1000 {
        compatible = "qcom,pm8941-charger";
@@ -128,4 +144,7 @@ charger@1000 {
 
        qcom,fast-charge-current-limit = <1000000>;
        qcom,dc-charge-current-limit = <1000000>;
+       usb_otg_in-supply = <&pm8941_5vs1>;
+
+       otg-vbus {};
 };
-- 
2.6.3

[PATCH v4 1/3] dt-binding: power: Add otg regulator binding

[Tim Bird]

Add a binding for the regulator which controls the OTG chargepath switch.
The OTG switch gets its power from pm8941_5vs1, and that should be
expressed as a usb_otg_in-supply property in the DT node for the
charger driver.  The regulator name is "otg-vbus".

Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
---
Changes since v3
 - switch supply name to have underscores instead of dashes
   - (switched back to match the name used in data sheets)
 - switch regulator node name to otg-vbus
Changes since v1
 - switch supply name to have dashes instead of underscores
 - remove superfluous DT explanations in the otg node description
---
 .../devicetree/bindings/power_supply/qcom_smbb.txt    | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
index 65b88fa..06f8a5d 100644
--- a/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
+++ b/Documentation/devicetree/bindings/power_supply/qcom_smbb.txt
@@ -105,6 +105,22 @@ PROPERTIES
                regulation must be done externally to fully comply with
                the JEITA safety guidelines if this flag is set.
 
+- usb_otg_in-supply:
+  Usage: optional
+  Value type: <phandle>
+  Description: Reference to the regulator supplying power to the USB_OTG_IN
+               pin.
+
+child nodes:
+- otg-vbus:
+  Usage: optional
+  Description: This node defines a regulator used to control the direction
+               of VBUS voltage - specifically: whether to supply voltage
+               to VBUS for host mode operation of the OTG port, or allow
+               input voltage from external VBUS for charging.  In the
+               hardware, the supply for this regulator comes from
+               usb_otg_in-supply.
+
 EXAMPLE
 charger@1000 {
        compatible = "qcom,pm8941-charger";
@@ -128,4 +144,7 @@ charger@1000 {
 
        qcom,fast-charge-current-limit = <1000000>;
        qcom,dc-charge-current-limit = <1000000>;
+       usb_otg_in-supply = <&pm8941_5vs1>;
+
+       otg-vbus {};
 };
-- 
2.6.3

[PATCH v4 2/3] power: qcom_smbb: Add otg regulator for control of vbus

[Tim Bird]

Add a regulator to control the OTG chargepath switch.  This
is used by USB code to control VBUS direction - out for host mode
on the OTG port, and in for charging mode.

Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
---
Changes since v3:
 - changed DT node name to otg-vbus
 - removed fixed-voltage setup from otg regulator rdesc
Changes since v1:
 - changed name of supply to remove underscores
---
 drivers/power/qcom_smbb.c | 72 +++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/drivers/power/qcom_smbb.c b/drivers/power/qcom_smbb.c
index 5eb1e9e..8998f4d 100644
--- a/drivers/power/qcom_smbb.c
+++ b/drivers/power/qcom_smbb.c
@@ -34,6 +34,9 @@
 #include <linux/power_supply.h>
 #include <linux/regmap.h>
 #include <linux/slab.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
 
 #define SMBB_CHG_VMAX		0x040
 #define SMBB_CHG_VSAFE		0x041
@@ -71,6 +74,8 @@
 #define BTC_CTRL_HOT_EXT_N	BIT(0)
 
 #define SMBB_USB_IMAX		0x344
+#define SMBB_USB_OTG_CTL	0x348
+#define OTG_CTL_EN		BIT(0)
 #define SMBB_USB_ENUM_TIMER_STOP 0x34e
 #define ENUM_TIMER_STOP		BIT(0)
 #define SMBB_USB_SEC_ACCESS	0x3d0
@@ -123,6 +128,9 @@ struct smbb_charger {
 	struct power_supply *dc_psy;
 	struct power_supply *bat_psy;
 	struct regmap *regmap;
+
+	struct regulator_desc otg_rdesc;
+	struct regulator_dev *otg_reg;
 };
 
 static int smbb_vbat_weak_fn(unsigned int index)
@@ -778,12 +786,56 @@ static const struct power_supply_desc dc_psy_desc = {
 	.property_is_writeable = smbb_charger_writable_property,
 };
 
+static int smbb_chg_otg_enable(struct regulator_dev *rdev)
+{
+	struct smbb_charger *chg = rdev_get_drvdata(rdev);
+	int rc;
+
+	rc = regmap_update_bits(chg->regmap, chg->addr + SMBB_USB_OTG_CTL,
+				OTG_CTL_EN, OTG_CTL_EN);
+	if (rc)
+		dev_err(chg->dev, "failed to update OTG_CTL\n");
+	return rc;
+}
+
+static int smbb_chg_otg_disable(struct regulator_dev *rdev)
+{
+	struct smbb_charger *chg = rdev_get_drvdata(rdev);
+	int rc;
+
+	rc = regmap_update_bits(chg->regmap, chg->addr + SMBB_USB_OTG_CTL,
+				OTG_CTL_EN, 0);
+	if (rc)
+		dev_err(chg->dev, "failed to update OTG_CTL\n");
+	return rc;
+}
+
+static int smbb_chg_otg_is_enabled(struct regulator_dev *rdev)
+{
+	struct smbb_charger *chg = rdev_get_drvdata(rdev);
+	unsigned int value = 0;
+	int rc;
+
+	rc = regmap_read(chg->regmap, chg->addr + SMBB_USB_OTG_CTL, &value);
+	if (rc)
+		dev_err(chg->dev, "failed to read OTG_CTL\n");
+
+	return !!(value & OTG_CTL_EN);
+}
+
+static struct regulator_ops smbb_chg_otg_ops = {
+	.enable = smbb_chg_otg_enable,
+	.disable = smbb_chg_otg_disable,
+	.is_enabled = smbb_chg_otg_is_enabled,
+};
+
 static int smbb_charger_probe(struct platform_device *pdev)
 {
 	struct power_supply_config bat_cfg = {};
 	struct power_supply_config usb_cfg = {};
 	struct power_supply_config dc_cfg = {};
 	struct smbb_charger *chg;
+	struct regulator_config config = { };
 	int rc, i;
 
 	chg = devm_kzalloc(&pdev->dev, sizeof(*chg), GFP_KERNEL);
@@ -884,6 +936,26 @@ static int smbb_charger_probe(struct platform_device *pdev)
 		}
 	}
 
+	/*
+	 * otg regulator is used to control VBUS voltage direction
+	 * when USB switches between host and gadget mode
+	 */
+	chg->otg_rdesc.id = -1;
+	chg->otg_rdesc.name = "otg-vbus";
+	chg->otg_rdesc.ops = &smbb_chg_otg_ops;
+	chg->otg_rdesc.owner = THIS_MODULE;
+	chg->otg_rdesc.type = REGULATOR_VOLTAGE;
+	chg->otg_rdesc.supply_name = "usb-otg-in";
+	chg->otg_rdesc.of_match = "otg-vbus";
+
+	config.dev = &pdev->dev;
+	config.driver_data = chg;
+
+	chg->otg_reg = devm_regulator_register(&pdev->dev, &chg->otg_rdesc,
+					       &config);
+	if (IS_ERR(chg->otg_reg))
+		return PTR_ERR(chg->otg_reg);
+
 	chg->jeita_ext_temp = of_property_read_bool(pdev->dev.of_node,
 			"qcom,jeita-extended-temp-range");
 
-- 
2.6.3

[PATCH v4 2/3] power: qcom_smbb: Add otg regulator for control of vbus

[Tim Bird]

Add a regulator to control the OTG chargepath switch.  This
is used by USB code to control VBUS direction - out for host mode
on the OTG port, and in for charging mode.

Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
---
Changes since v3:
 - changed DT node name to otg-vbus
 - removed fixed-voltage setup from otg regulator rdesc
Changes since v1:
 - changed name of supply to remove underscores
---
 drivers/power/qcom_smbb.c | 72 +++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/drivers/power/qcom_smbb.c b/drivers/power/qcom_smbb.c
index 5eb1e9e..8998f4d 100644
--- a/drivers/power/qcom_smbb.c
+++ b/drivers/power/qcom_smbb.c
@@ -34,6 +34,9 @@
 #include <linux/power_supply.h>
 #include <linux/regmap.h>
 #include <linux/slab.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
 
 #define SMBB_CHG_VMAX		0x040
 #define SMBB_CHG_VSAFE		0x041
@@ -71,6 +74,8 @@
 #define BTC_CTRL_HOT_EXT_N	BIT(0)
 
 #define SMBB_USB_IMAX		0x344
+#define SMBB_USB_OTG_CTL	0x348
+#define OTG_CTL_EN		BIT(0)
 #define SMBB_USB_ENUM_TIMER_STOP 0x34e
 #define ENUM_TIMER_STOP		BIT(0)
 #define SMBB_USB_SEC_ACCESS	0x3d0
@@ -123,6 +128,9 @@ struct smbb_charger {
 	struct power_supply *dc_psy;
 	struct power_supply *bat_psy;
 	struct regmap *regmap;
+
+	struct regulator_desc otg_rdesc;
+	struct regulator_dev *otg_reg;
 };
 
 static int smbb_vbat_weak_fn(unsigned int index)
@@ -778,12 +786,56 @@ static const struct power_supply_desc dc_psy_desc = {
 	.property_is_writeable = smbb_charger_writable_property,
 };
 
+static int smbb_chg_otg_enable(struct regulator_dev *rdev)
+{
+	struct smbb_charger *chg = rdev_get_drvdata(rdev);
+	int rc;
+
+	rc = regmap_update_bits(chg->regmap, chg->addr + SMBB_USB_OTG_CTL,
+				OTG_CTL_EN, OTG_CTL_EN);
+	if (rc)
+		dev_err(chg->dev, "failed to update OTG_CTL\n");
+	return rc;
+}
+
+static int smbb_chg_otg_disable(struct regulator_dev *rdev)
+{
+	struct smbb_charger *chg = rdev_get_drvdata(rdev);
+	int rc;
+
+	rc = regmap_update_bits(chg->regmap, chg->addr + SMBB_USB_OTG_CTL,
+				OTG_CTL_EN, 0);
+	if (rc)
+		dev_err(chg->dev, "failed to update OTG_CTL\n");
+	return rc;
+}
+
+static int smbb_chg_otg_is_enabled(struct regulator_dev *rdev)
+{
+	struct smbb_charger *chg = rdev_get_drvdata(rdev);
+	unsigned int value = 0;
+	int rc;
+
+	rc = regmap_read(chg->regmap, chg->addr + SMBB_USB_OTG_CTL, &value);
+	if (rc)
+		dev_err(chg->dev, "failed to read OTG_CTL\n");
+
+	return !!(value & OTG_CTL_EN);
+}
+
+static struct regulator_ops smbb_chg_otg_ops = {
+	.enable = smbb_chg_otg_enable,
+	.disable = smbb_chg_otg_disable,
+	.is_enabled = smbb_chg_otg_is_enabled,
+};
+
 static int smbb_charger_probe(struct platform_device *pdev)
 {
 	struct power_supply_config bat_cfg = {};
 	struct power_supply_config usb_cfg = {};
 	struct power_supply_config dc_cfg = {};
 	struct smbb_charger *chg;
+	struct regulator_config config = { };
 	int rc, i;
 
 	chg = devm_kzalloc(&pdev->dev, sizeof(*chg), GFP_KERNEL);
@@ -884,6 +936,26 @@ static int smbb_charger_probe(struct platform_device *pdev)
 		}
 	}
 
+	/*
+	 * otg regulator is used to control VBUS voltage direction
+	 * when USB switches between host and gadget mode
+	 */
+	chg->otg_rdesc.id = -1;
+	chg->otg_rdesc.name = "otg-vbus";
+	chg->otg_rdesc.ops = &smbb_chg_otg_ops;
+	chg->otg_rdesc.owner = THIS_MODULE;
+	chg->otg_rdesc.type = REGULATOR_VOLTAGE;
+	chg->otg_rdesc.supply_name = "usb-otg-in";
+	chg->otg_rdesc.of_match = "otg-vbus";
+
+	config.dev = &pdev->dev;
+	config.driver_data = chg;
+
+	chg->otg_reg = devm_regulator_register(&pdev->dev, &chg->otg_rdesc,
+					       &config);
+	if (IS_ERR(chg->otg_reg))
+		return PTR_ERR(chg->otg_reg);
+
 	chg->jeita_ext_temp = of_property_read_bool(pdev->dev.of_node,
 			"qcom,jeita-extended-temp-range");
 
-- 
2.6.3

Re: [PATCH v4 2/3] power: qcom_smbb: Add otg regulator for control of vbus

[Bjorn Andersson]

On Tue 15 Dec 11:52 PST 2015, Tim Bird wrote:

> Add a regulator to control the OTG chargepath switch.  This
> is used by USB code to control VBUS direction - out for host mode
> on the OTG port, and in for charging mode.
> 
> Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
> ---
> Changes since v3:
>  - changed DT node name to otg-vbus
>  - removed fixed-voltage setup from otg regulator rdesc
> Changes since v1:
>  - changed name of supply to remove underscores
> ---

Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>

Regards,
Bjorn

Re: [PATCH v4 2/3] power: qcom_smbb: Add otg regulator for control of vbus

[Andy Gross]

On Tue, Dec 15, 2015 at 11:52:11AM -0800, Tim Bird wrote:
> Add a regulator to control the OTG chargepath switch.  This
> is used by USB code to control VBUS direction - out for host mode
> on the OTG port, and in for charging mode.
> 
> Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
> ---
> Changes since v3:
>  - changed DT node name to otg-vbus
>  - removed fixed-voltage setup from otg regulator rdesc
> Changes since v1:
>  - changed name of supply to remove underscores
> ---

Reviewed-by: Andy Gross <andy.gross@linaro.org>

[PATCH v4 3/3] ARM: dts: qcom: add charger otg regulator

[Tim Bird]

Add the otg regulator provided by the charger block.

Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
---
Changes since V3:
 - change name of charger regulator to "otg-vbus"
---
 arch/arm/boot/dts/qcom-pm8941.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index b0d4439..d0ffca7 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -45,6 +45,10 @@
 					  "chg-gone",
 					  "usb-valid",
 					  "dc-valid";
+
+			usb_otg_in-supply = <&pm8941_5vs1>;
+
+			chg_otg: otg-vbus { };
 		};
 
 		pm8941_gpios: gpios@c000 {
-- 
2.6.3

[PATCH v4 3/3] ARM: dts: qcom: add charger otg regulator

[Tim Bird]

Add the otg regulator provided by the charger block.

Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
---
Changes since V3:
 - change name of charger regulator to "otg-vbus"
---
 arch/arm/boot/dts/qcom-pm8941.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index b0d4439..d0ffca7 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -45,6 +45,10 @@
 					  "chg-gone",
 					  "usb-valid",
 					  "dc-valid";
+
+			usb_otg_in-supply = <&pm8941_5vs1>;
+
+			chg_otg: otg-vbus { };
 		};
 
 		pm8941_gpios: gpios@c000 {
-- 
2.6.3

Re: [PATCH v4 3/3] ARM: dts: qcom: add charger otg regulator

[Bjorn Andersson]

On Tue 15 Dec 11:52 PST 2015, Tim Bird wrote:

> Add the otg regulator provided by the charger block.
> 
> Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
> ---
> Changes since V3:
>  - change name of charger regulator to "otg-vbus"
> ---
>  arch/arm/boot/dts/qcom-pm8941.dtsi | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
> index b0d4439..d0ffca7 100644
> --- a/arch/arm/boot/dts/qcom-pm8941.dtsi
> +++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
> @@ -45,6 +45,10 @@
>  					  "chg-gone",
>  					  "usb-valid",
>  					  "dc-valid";
> +
> +			usb_otg_in-supply = <&pm8941_5vs1>;

Although this could be coming from some other supply I think it's
perfectly fine that we define this on a platform level.

> +
> +			chg_otg: otg-vbus { };
>  		};
>  
>  		pm8941_gpios: gpios@c000 {

Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>

Regards,
Bjorn

Re: [PATCH v4 1/3] dt-binding: power: Add otg regulator binding

[Bjorn Andersson]

On Tue 15 Dec 11:52 PST 2015, Tim Bird wrote:

> Add a binding for the regulator which controls the OTG chargepath switch.
> The OTG switch gets its power from pm8941_5vs1, and that should be
> expressed as a usb_otg_in-supply property in the DT node for the
> charger driver.  The regulator name is "otg-vbus".
> 
> Signed-off-by: Tim Bird <tim.bird-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>
> ---
> Changes since v3
>  - switch supply name to have underscores instead of dashes
>    - (switched back to match the name used in data sheets)

Thanks, now it matches the datasheet again.

>  - switch regulator node name to otg-vbus
> Changes since v1
>  - switch supply name to have dashes instead of underscores
>  - remove superfluous DT explanations in the otg node description
> ---

Acked-by: Bjorn Andersson <bjorn.andersson-/MT0OVThwyLZJqsBc5GL+g@public.gmane.org>

Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v4 1/3] dt-binding: power: Add otg regulator binding

[Bjorn Andersson]

On Tue 15 Dec 11:52 PST 2015, Tim Bird wrote:

> Add a binding for the regulator which controls the OTG chargepath switch.
> The OTG switch gets its power from pm8941_5vs1, and that should be
> expressed as a usb_otg_in-supply property in the DT node for the
> charger driver.  The regulator name is "otg-vbus".
> 
> Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
> ---
> Changes since v3
>  - switch supply name to have underscores instead of dashes
>    - (switched back to match the name used in data sheets)

Thanks, now it matches the datasheet again.

>  - switch regulator node name to otg-vbus
> Changes since v1
>  - switch supply name to have dashes instead of underscores
>  - remove superfluous DT explanations in the otg node description
> ---

Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>

Regards,
Bjorn

Re: [PATCH v4 1/3] dt-binding: power: Add otg regulator binding

[Andy Gross]

On Tue, Dec 15, 2015 at 11:52:10AM -0800, Tim Bird wrote:
> Add a binding for the regulator which controls the OTG chargepath switch.
> The OTG switch gets its power from pm8941_5vs1, and that should be
> expressed as a usb_otg_in-supply property in the DT node for the
> charger driver.  The regulator name is "otg-vbus".
> 
> Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
> ---
> Changes since v3
>  - switch supply name to have underscores instead of dashes
>    - (switched back to match the name used in data sheets)
>  - switch regulator node name to otg-vbus
> Changes since v1
>  - switch supply name to have dashes instead of underscores
>  - remove superfluous DT explanations in the otg node description

Reviewed-by: Andy Gross <andy.gross@linaro.org>

Re: [PATCH v4 1/3] dt-binding: power: Add otg regulator binding

[Sebastian Reichel]

[-- Attachment #1: Type: text/plain, Size: 478 bytes --]

Hi,

On Tue, Dec 15, 2015 at 11:52:10AM -0800, Tim Bird wrote:
> Add a binding for the regulator which controls the OTG chargepath switch.
> The OTG switch gets its power from pm8941_5vs1, and that should be
> expressed as a usb_otg_in-supply property in the DT node for the
> charger driver. The regulator name is "otg-vbus".

I would like to get an acked-by from either the regulator framework
maintainers, or DT binding maintainers (or both ;)) on the binding.

-- Sebastian

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]

Re: [PATCH v4 1/3] dt-binding: power: Add otg regulator binding

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 699 bytes --]

On Wed, Dec 16, 2015 at 12:13:50AM +0100, Sebastian Reichel wrote:
> On Tue, Dec 15, 2015 at 11:52:10AM -0800, Tim Bird wrote:
> > Add a binding for the regulator which controls the OTG chargepath switch.
> > The OTG switch gets its power from pm8941_5vs1, and that should be
> > expressed as a usb_otg_in-supply property in the DT node for the
> > charger driver. The regulator name is "otg-vbus".

> I would like to get an acked-by from either the regulator framework
> maintainers, or DT binding maintainers (or both ;)) on the binding.

Please submit any patches you want reviewing using the process in
SubmittingPatches.  If this is a regulator driver it should be in
drivers/regulator though.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 473 bytes --]

Re: [PATCH v4 1/3] dt-binding: power: Add otg regulator binding

[Rob Herring]

On Tue, Dec 15, 2015 at 11:52:10AM -0800, Tim Bird wrote:
> Add a binding for the regulator which controls the OTG chargepath switch.
> The OTG switch gets its power from pm8941_5vs1, and that should be
> expressed as a usb_otg_in-supply property in the DT node for the
> charger driver.  The regulator name is "otg-vbus".
> 
> Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
> ---
> Changes since v3
>  - switch supply name to have underscores instead of dashes
>    - (switched back to match the name used in data sheets)
>  - switch regulator node name to otg-vbus
> Changes since v1
>  - switch supply name to have dashes instead of underscores
>  - remove superfluous DT explanations in the otg node description
> ---
>  .../devicetree/bindings/power_supply/qcom_smbb.txt    | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)

Acked-by: Rob Herring <robh@kernel.org>