* [PATCH 2/2] ARM: dts: Add dts for Uniwest evi
@ 2016-02-01 12:11 ` Shawn Guo
0 siblings, 0 replies; 32+ messages in thread
From: Shawn Guo @ 2016-02-01 12:11 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Jan 13, 2016 at 12:45:12PM -0800, Joshua Clayton wrote:
> Uniwest evi is a portable electrical eddy current non-destructive
> testing device.
>
> Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
> ---
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 30bbc37..c284cb6 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -314,6 +314,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-cubox-i.dtb \
> imx6q-dfi-fs700-m60.dtb \
> imx6q-dmo-edmqmx6.dtb \
> + imx6q-evi.dtb \
> imx6q-gk802.dtb \
> imx6q-gw51xx.dtb \
> imx6q-gw52xx.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
> new file mode 100644
> index 0000000..a1ca2b9
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-evi.dts
> @@ -0,0 +1,502 @@
> +/*
> + * Copyright 2016 United Western Technologies.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + *
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "Uniwest Evi";
> + compatible = "uniwest,imx6q-evi", "fsl,imx6q";
> +
> + memory {
> + reg = <0x10000000 0x40000000>;
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_usbh1_vbus: regulator at 0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "usbh1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + startup-delay-us = <2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh1_hubreset>;
> + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
> + };
Device tree maintainers do not like the fake simple-bus container for
these fixed regulators. We are asked to put them directly under root
node. In that case, we do not need the artificial 'reg' property, and
we can name node in schema like:
reg_xxx: regulator-xxx {
...
}
> +
> + reg_usb_otg_vbus: regulator at 1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg_vbus>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> + };
Have a new line between nodes.
> + chosen {
> + bootargs = "sbs-battery.force_load=1";
> + };
We generally put 'chosen' node at the beginning along with 'memory'
node. And do we really need this as the default bootargs?
> +
> + panel {
> + compatible = "sharp,lq101k1ly04";
Undocumented compatible string.
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +};
> +
> +&ecspi1 {
> + fsl,spi-num-chipselects = <1>;
> + cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_extra>;
You use only one GPIO in cs-gpios. Why do you need to set up 3 in
pinctrl_ecspi1_extra? And why do you name the pinctrl group in the same
way as ecspi3 and ecspi5, i.e. pinctrl_ecspi1_cs?
> + status = "okay";
> +};
> +
> +&ecspi3 {
> + fsl,spi-num-chipselects = <3>;
> + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
> + <&gpio4 25 GPIO_ACTIVE_LOW>,
> + <&gpio4 26 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs>;
> + status = "okay";
> +};
> +
> +&ecspi5 {
> + fsl,spi-num-chipselects = <4>;
> + cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
> + <&gpio1 13 GPIO_ACTIVE_LOW>,
> + <&gpio1 12 GPIO_ACTIVE_LOW>,
> + <&gpio2 9 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5_cs>;
> + status = "okay";
Have a new line between properties and sub-node.
> + eeprom: m95m02 at 1 {
> + compatible = "st,m95m02", "atmel,at25";
> + size = <262144>;
> + pagesize = <256>;
> + address-width = <24>;
> + spi-max-frequency = <5000000>;
> + reg = <1>;
> + };
Have a new line between nodes.
> + pb_rtc: rtc at 3 {
> + compatible = "nxp,rtc-pcf2123";
> + spi-max-frequency = <2450000>;
> + spi-cs-high;
> + reg = <3>;
> + };
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rgmii";
> + phy-reset-gpios = <&gpio1 25 0>;
> + status = "okay";
> +};
> +
> +&gpmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpmi_nand>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + clock-frequency = <100000>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + pinctrl-1 = <&pinctrl_i2c3_gpio>;
> + clock-frequency = <100000>;
> + status = "okay";
We generally put 'status' at the bottom of the property list.
> + scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
> + sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
> +
> + battery: sbs-battery at b {
> + compatible = "sbs,sbs-battery";
> + reg = <0x0b>;
> + sbs,poll-retry-count = <100>;
> + sbs,i2c-retry-count = <100>;
> + };
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds0: lvds-channel at 0 {
> + fsl,data-mapping = "jeida";
> + fsl,data-width = <24>;
> + status = "okay";
> +
> + port at 4 {
> + reg = <4>;
> +
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
> +
> +&ssi1 {
> + fsl,mode = "i2s-slave";
"i2s-slave" is deprecated for fsl,mode, and can be just dropped.
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usbh1_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh1>;
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + disable-over-current;
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&weim {
> + #address-cells = <2>;
> + #size-cells = <1>;
> + ranges = <0 0 0x08000000 0x08000000>;
> + fsl,weim-cs-gpr = <&gpr>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_weim_fpga &pinctrl_weim_cs>;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + imx6q-evi {
Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without
function nodes), this additional container node can just be saved.
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + /* CPLD Reset */
> + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
> + /* pwr mcu alert irq */
> + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
> + /* remainder ???? */
> + MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
> + >;
> + };
Have a new line between nodes.
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
> + MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
> + MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
> + >;
> + };
> + pinctrl_ecspi1_extra: ecspi1extragrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
> + MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0
> + MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0
> + >;
> + };
> + pinctrl_ecspi3: ecspi3grp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x10068
> + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x10068
> + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x1f068
> + >;
> + };
> + pinctrl_ecspi3_cs: ecspi3cs {
Please name the node consistently, like xxxgrp.
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
> + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b0
> + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
> + MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
> + >;
> + };
> + pinctrl_ecspi5: ecspi5grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK 0x100b1
> + MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI 0x100b1
> + MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO 0x100b1
> + >;
> + };
> + pinctrl_ecspi5_cs: ecspi5cs {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
> + MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x1b0b0
> + MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
> + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
> + >;
> + };
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x4001b0a8
> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> + >;
> + };
> + pinctrl_gpmi_nand: gpminandgrp {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
> + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
> + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
> + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
> + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
> + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
> + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
> + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
> + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
> + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
> + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
> + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
> + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
> + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
> + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
> + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
> + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
> + >;
> + };
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + >;
> + };
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
> + >;
> + };
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1
> + MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001b8b1
> + >;
> + };
> + pinctrl_weim_cs: weim_csgrp {
weimcsgrp
> + fsl,pins = <
> + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
> + MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1
> + >;
> + };
> + pinctrl_weim_fpga: weim_fpgagrp {
weimfpgagrp
> + fsl,pins = <
> + /* weim misc */
> + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
> + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
> + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
> + MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0b1
> + MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0b1
> + MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0xb0b1
> + MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0xb0b1
> + MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0xb0b1
> + MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0xb0b1
> + /* weim data */
> + MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x1b0b0
> + MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x1b0b0
> + MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
> + MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
> + MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
> + MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
> + MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
> + MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
> + MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
> + MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
> + MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
> + MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
> + MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
> + MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
> + MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
> + MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
> + MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
> + MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
> + /* weim address */
> + MX6QDL_PAD_EIM_A25__EIM_ADDR25 0xb0b1
> + MX6QDL_PAD_EIM_A24__EIM_ADDR24 0xb0b1
> + MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
> + MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
> + MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
> + MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
> + MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
> + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
> + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
> + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
> + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
> + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
> + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
> + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
> + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
> + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
> + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
> + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
> + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
> + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
> + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
> + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
> + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
> + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
> + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
> + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
> + >;
> + };
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
> + >;
> + };
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
> + MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
> + MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x1b0b1
> + MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x1b0b1
> + >;
> + };
> + pinctrl_usbh1: usbh1grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0
> + /* usbh1_b OC */
> + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
> + >;
> + };
> + pinctrl_usbh1_hubreset: usbh1hubresetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
> + >;
> + };
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
> + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
> + >;
> + };
> + pinctrl_usbotg_vbus: usbotg_vbusgrp {
usbotgvbusgrp
Shawn
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
> + >;
> + };
> + };
> +};
> --
> 2.5.0
>
>
^ permalink raw reply [flat|nested] 32+ messages in thread* Re: [PATCH 2/2] ARM: dts: Add dts for Uniwest evi
@ 2016-02-01 12:11 ` Shawn Guo
0 siblings, 0 replies; 32+ messages in thread
From: Shawn Guo @ 2016-02-01 12:11 UTC (permalink / raw)
To: Joshua Clayton
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, Sascha Hauer, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On Wed, Jan 13, 2016 at 12:45:12PM -0800, Joshua Clayton wrote:
> Uniwest evi is a portable electrical eddy current non-destructive
> testing device.
>
> Signed-off-by: Joshua Clayton <stillcompiling-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 30bbc37..c284cb6 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -314,6 +314,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-cubox-i.dtb \
> imx6q-dfi-fs700-m60.dtb \
> imx6q-dmo-edmqmx6.dtb \
> + imx6q-evi.dtb \
> imx6q-gk802.dtb \
> imx6q-gw51xx.dtb \
> imx6q-gw52xx.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
> new file mode 100644
> index 0000000..a1ca2b9
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-evi.dts
> @@ -0,0 +1,502 @@
> +/*
> + * Copyright 2016 United Western Technologies.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + *
> + */
> +
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "Uniwest Evi";
> + compatible = "uniwest,imx6q-evi", "fsl,imx6q";
> +
> + memory {
> + reg = <0x10000000 0x40000000>;
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_usbh1_vbus: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "usbh1_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + startup-delay-us = <2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh1_hubreset>;
> + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
> + };
Device tree maintainers do not like the fake simple-bus container for
these fixed regulators. We are asked to put them directly under root
node. In that case, we do not need the artificial 'reg' property, and
we can name node in schema like:
reg_xxx: regulator-xxx {
...
}
> +
> + reg_usb_otg_vbus: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg_vbus>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> + };
Have a new line between nodes.
> + chosen {
> + bootargs = "sbs-battery.force_load=1";
> + };
We generally put 'chosen' node at the beginning along with 'memory'
node. And do we really need this as the default bootargs?
> +
> + panel {
> + compatible = "sharp,lq101k1ly04";
Undocumented compatible string.
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +};
> +
> +&ecspi1 {
> + fsl,spi-num-chipselects = <1>;
> + cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_extra>;
You use only one GPIO in cs-gpios. Why do you need to set up 3 in
pinctrl_ecspi1_extra? And why do you name the pinctrl group in the same
way as ecspi3 and ecspi5, i.e. pinctrl_ecspi1_cs?
> + status = "okay";
> +};
> +
> +&ecspi3 {
> + fsl,spi-num-chipselects = <3>;
> + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
> + <&gpio4 25 GPIO_ACTIVE_LOW>,
> + <&gpio4 26 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs>;
> + status = "okay";
> +};
> +
> +&ecspi5 {
> + fsl,spi-num-chipselects = <4>;
> + cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
> + <&gpio1 13 GPIO_ACTIVE_LOW>,
> + <&gpio1 12 GPIO_ACTIVE_LOW>,
> + <&gpio2 9 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5_cs>;
> + status = "okay";
Have a new line between properties and sub-node.
> + eeprom: m95m02@1 {
> + compatible = "st,m95m02", "atmel,at25";
> + size = <262144>;
> + pagesize = <256>;
> + address-width = <24>;
> + spi-max-frequency = <5000000>;
> + reg = <1>;
> + };
Have a new line between nodes.
> + pb_rtc: rtc@3 {
> + compatible = "nxp,rtc-pcf2123";
> + spi-max-frequency = <2450000>;
> + spi-cs-high;
> + reg = <3>;
> + };
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rgmii";
> + phy-reset-gpios = <&gpio1 25 0>;
> + status = "okay";
> +};
> +
> +&gpmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpmi_nand>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + clock-frequency = <100000>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + pinctrl-1 = <&pinctrl_i2c3_gpio>;
> + clock-frequency = <100000>;
> + status = "okay";
We generally put 'status' at the bottom of the property list.
> + scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
> + sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
> +
> + battery: sbs-battery@b {
> + compatible = "sbs,sbs-battery";
> + reg = <0x0b>;
> + sbs,poll-retry-count = <100>;
> + sbs,i2c-retry-count = <100>;
> + };
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds0: lvds-channel@0 {
> + fsl,data-mapping = "jeida";
> + fsl,data-width = <24>;
> + status = "okay";
> +
> + port@4 {
> + reg = <4>;
> +
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
> +
> +&ssi1 {
> + fsl,mode = "i2s-slave";
"i2s-slave" is deprecated for fsl,mode, and can be just dropped.
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&usbh1 {
> + vbus-supply = <®_usbh1_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbh1>;
> + dr_mode = "host";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + disable-over-current;
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&weim {
> + #address-cells = <2>;
> + #size-cells = <1>;
> + ranges = <0 0 0x08000000 0x08000000>;
> + fsl,weim-cs-gpr = <&gpr>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_weim_fpga &pinctrl_weim_cs>;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + imx6q-evi {
Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without
function nodes), this additional container node can just be saved.
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + /* CPLD Reset */
> + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
> + /* pwr mcu alert irq */
> + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
> + /* remainder ???? */
> + MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
> + >;
> + };
Have a new line between nodes.
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
> + MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
> + MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
> + >;
> + };
> + pinctrl_ecspi1_extra: ecspi1extragrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
> + MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0
> + MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0
> + >;
> + };
> + pinctrl_ecspi3: ecspi3grp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x10068
> + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x10068
> + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x1f068
> + >;
> + };
> + pinctrl_ecspi3_cs: ecspi3cs {
Please name the node consistently, like xxxgrp.
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
> + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b0
> + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
> + MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
> + >;
> + };
> + pinctrl_ecspi5: ecspi5grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK 0x100b1
> + MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI 0x100b1
> + MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO 0x100b1
> + >;
> + };
> + pinctrl_ecspi5_cs: ecspi5cs {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
> + MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x1b0b0
> + MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
> + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
> + >;
> + };
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x4001b0a8
> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> + >;
> + };
> + pinctrl_gpmi_nand: gpminandgrp {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
> + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
> + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
> + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
> + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
> + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
> + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
> + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
> + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
> + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
> + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
> + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
> + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
> + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
> + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
> + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
> + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
> + >;
> + };
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + >;
> + };
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
> + >;
> + };
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1
> + MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001b8b1
> + >;
> + };
> + pinctrl_weim_cs: weim_csgrp {
weimcsgrp
> + fsl,pins = <
> + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
> + MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1
> + >;
> + };
> + pinctrl_weim_fpga: weim_fpgagrp {
weimfpgagrp
> + fsl,pins = <
> + /* weim misc */
> + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
> + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
> + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
> + MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0b1
> + MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0b1
> + MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0xb0b1
> + MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0xb0b1
> + MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0xb0b1
> + MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0xb0b1
> + /* weim data */
> + MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x1b0b0
> + MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x1b0b0
> + MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
> + MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
> + MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
> + MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
> + MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
> + MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
> + MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
> + MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
> + MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
> + MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
> + MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
> + MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
> + MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
> + MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
> + MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
> + MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
> + /* weim address */
> + MX6QDL_PAD_EIM_A25__EIM_ADDR25 0xb0b1
> + MX6QDL_PAD_EIM_A24__EIM_ADDR24 0xb0b1
> + MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
> + MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
> + MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
> + MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
> + MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
> + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
> + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
> + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
> + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
> + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
> + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
> + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
> + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
> + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
> + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
> + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
> + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
> + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
> + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
> + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
> + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
> + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
> + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
> + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
> + >;
> + };
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
> + >;
> + };
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
> + MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
> + MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x1b0b1
> + MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x1b0b1
> + >;
> + };
> + pinctrl_usbh1: usbh1grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0
> + /* usbh1_b OC */
> + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
> + >;
> + };
> + pinctrl_usbh1_hubreset: usbh1hubresetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
> + >;
> + };
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
> + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
> + >;
> + };
> + pinctrl_usbotg_vbus: usbotg_vbusgrp {
usbotgvbusgrp
Shawn
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
> + >;
> + };
> + };
> +};
> --
> 2.5.0
>
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 32+ messages in thread* Re: [PATCH 2/2] ARM: dts: Add dts for Uniwest evi
2016-02-01 12:11 ` Shawn Guo
(?)
@ 2016-02-02 21:21 ` Joshua Clayton
-1 siblings, 0 replies; 32+ messages in thread
From: Joshua Clayton @ 2016-02-02 21:21 UTC (permalink / raw)
To: Shawn Guo
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, Sascha Hauer, devicetree, linux-arm-kernel,
linux-kernel
Shawn,
thanks for the review.
I've tried to address your concerns.
I have a new dts which I will send once I've booted it.
On Mon, 1 Feb 2016 20:11:45 +0800
Shawn Guo <shawnguo@kernel.org> wrote:
...
> > + regulators {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + reg_usbh1_vbus: regulator@0 {
> > + compatible = "regulator-fixed";
> > + reg = <0>;
> > + regulator-name = "usbh1_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + enable-active-high;
> > + startup-delay-us = <2>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbh1_hubreset>;
> > + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
> > + };
>
> Device tree maintainers do not like the fake simple-bus container for
> these fixed regulators. We are asked to put them directly under root
> node. In that case, we do not need the artificial 'reg' property, and
> we can name node in schema like:
>
> reg_xxx: regulator-xxx {
> ...
> }
>
OK. will do.
> > +
> > + reg_usb_otg_vbus: regulator@1 {
> > + compatible = "regulator-fixed";
> > + reg = <1>;
> > + regulator-name = "usb_otg_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg_vbus>;
> > + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + };
> > + };
>
> Have a new line between nodes.
OK.
>
> > + chosen {
> > + bootargs = "sbs-battery.force_load=1";
> > + };
>
> We generally put 'chosen' node at the beginning along with 'memory'
> node. And do we really need this as the default bootargs?
It is needed because if the battery is not installed at boot time,
the device fails to probe as the dts is being parsed, and there is
no way for the kernel to be made aware later.
I guess I could put this into uboot kernel args instead...
I'll remove it for now.
> > +
> > + panel {
> > + compatible = "sharp,lq101k1ly04";
>
> Undocumented compatible string.
This is making its way through the drm list. Its a simple-panel
compatible set of timings.
>
> > +
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&lvds0_out>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&ecspi1 {
> > + fsl,spi-num-chipselects = <1>;
> > + cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_extra>;
>
> You use only one GPIO in cs-gpios. Why do you need to set up 3 in
> pinctrl_ecspi1_extra? And why do you name the pinctrl group in the
> same way as ecspi3 and ecspi5, i.e. pinctrl_ecspi1_cs?
There is only 1 chip select for this spi node.
The extra pins are related to a not-yet-upstreamed driver.
I'll remove them and call it pinctrl_ecspi1_cs
>
> > + status = "okay";
> > +};
> > +
> > +&ecspi3 {
> > + fsl,spi-num-chipselects = <3>;
> > + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
> > + <&gpio4 25 GPIO_ACTIVE_LOW>,
> > + <&gpio4 26 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs>;
> > + status = "okay";
> > +};
> > +
> > +&ecspi5 {
> > + fsl,spi-num-chipselects = <4>;
> > + cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
> > + <&gpio1 13 GPIO_ACTIVE_LOW>,
> > + <&gpio1 12 GPIO_ACTIVE_LOW>,
> > + <&gpio2 9 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5_cs>;
> > + status = "okay";
>
> Have a new line between properties and sub-node.
Will do. Thanks.
>
> > + eeprom: m95m02@1 {
> > + compatible = "st,m95m02", "atmel,at25";
> > + size = <262144>;
> > + pagesize = <256>;
> > + address-width = <24>;
> > + spi-max-frequency = <5000000>;
> > + reg = <1>;
> > + };
>
> Have a new line between nodes.
OK.
>
> > + pb_rtc: rtc@3 {
> > + compatible = "nxp,rtc-pcf2123";
> > + spi-max-frequency = <2450000>;
> > + spi-cs-high;
> > + reg = <3>;
> > + };
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rgmii";
> > + phy-reset-gpios = <&gpio1 25 0>;
> > + status = "okay";
> > +};
> > +
> > +&gpmi {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_gpmi_nand>;
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + clock-frequency = <100000>;
> > + status = "okay";
> > +};
> > +
> > +&i2c3 {
> > + pinctrl-names = "default", "gpio";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + pinctrl-1 = <&pinctrl_i2c3_gpio>;
> > + clock-frequency = <100000>;
> > + status = "okay";
>
> We generally put 'status' at the bottom of the property list.
Will move it.
>
> > + scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
> > + sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
> > +
> > + battery: sbs-battery@b {
> > + compatible = "sbs,sbs-battery";
> > + reg = <0x0b>;
> > + sbs,poll-retry-count = <100>;
> > + sbs,i2c-retry-count = <100>;
> > + };
> > +};
> > +
> > +&ldb {
> > + status = "okay";
> > +
> > + lvds0: lvds-channel@0 {
> > + fsl,data-mapping = "jeida";
> > + fsl,data-width = <24>;
> > + status = "okay";
> > +
> > + port@4 {
> > + reg = <4>;
> > +
> > + lvds0_out: endpoint {
> > + remote-endpoint = <&panel_in>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&ssi1 {
> > + fsl,mode = "i2s-slave";
>
> "i2s-slave" is deprecated for fsl,mode, and can be just dropped.
OK.
>
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart2>;
> > + status = "okay";
> > +};
> > +
> > +&usbh1 {
> > + vbus-supply = <®_usbh1_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbh1>;
> > + dr_mode = "host";
> > + disable-over-current;
> > + status = "okay";
> > +};
> > +
> > +&usbotg {
> > + vbus-supply = <®_usb_otg_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg>;
> > + disable-over-current;
> > + dr_mode = "otg";
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&weim {
> > + #address-cells = <2>;
> > + #size-cells = <1>;
> > + ranges = <0 0 0x08000000 0x08000000>;
> > + fsl,weim-cs-gpr = <&gpr>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_weim_fpga &pinctrl_weim_cs>;
> > + status = "okay";
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hog>;
> > +
> > + imx6q-evi {
>
> Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without
> function nodes), this additional container node can just be saved.
So these should be directly under iomux... ok. Will do
>
> > + pinctrl_hog: hoggrp {
> > + fsl,pins = <
> > + /* CPLD Reset */
> > + MX6QDL_PAD_GPIO_19__GPIO4_IO05
> > 0x1b0b0
> > + /* pwr mcu alert irq */
> > + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10
> > 0x1b0b0
> > + /* remainder ???? */
> > + MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19
> > 0x1b0b0
> > + >;
> > + };
>
> Have a new line between nodes.
OK.
>
> > + pinctrl_ecspi1: ecspi1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL1__ECSPI1_MISO
> > 0x100b1
> > + MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI
> > 0x100b1
> > + MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK
> > 0x100b1
> > + >;
> > + };
> > + pinctrl_ecspi1_extra: ecspi1extragrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL2__GPIO4_IO10
> > 0x1b0b0
> > + MX6QDL_PAD_KEY_ROW1__GPIO4_IO09
> > 0x1b0b0
> > + MX6QDL_PAD_KEY_ROW2__GPIO4_IO11
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_ecspi3: ecspi3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK
> > 0x10068
> > + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI
> > 0x10068
> > + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO
> > 0x1f068
> > + >;
> > + };
> > + pinctrl_ecspi3_cs: ecspi3cs {
>
> Please name the node consistently, like xxxgrp.
OK.
>
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24
> > 0x1b0b0
> > + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25
> > 0x1b0b0
> > + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26
> > 0x1b0b0
> > + MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_ecspi5: ecspi5grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK
> > 0x100b1
> > + MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI
> > 0x100b1
> > + MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO
> > 0x100b1
> > + >;
> > + };
> > + pinctrl_ecspi5_cs: ecspi5cs {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_DAT1__GPIO1_IO14
> > 0x1b0b0
> > + MX6QDL_PAD_SD2_DAT2__GPIO1_IO13
> > 0x1b0b0
> > + MX6QDL_PAD_SD2_DAT3__GPIO1_IO12
> > 0x1b0b0
> > + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_enet: enetgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO
> > 0x1b0b0
> > + MX6QDL_PAD_ENET_MDC__ENET_MDC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3
> > 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> > +
> > MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3
> > 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> > + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN
> > 0x4001b0a8
> > + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_gpmi_nand: gpminandgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_CLE__NAND_CLE
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_ALE__NAND_ALE
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_RB0__NAND_READY_B
> > 0xb000
> > + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B
> > 0xb0b1
> > + MX6QDL_PAD_SD4_CMD__NAND_RE_B
> > 0xb0b1
> > + MX6QDL_PAD_SD4_CLK__NAND_WE_B
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D0__NAND_DATA00
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D1__NAND_DATA01
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D2__NAND_DATA02
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D3__NAND_DATA03
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D4__NAND_DATA04
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D5__NAND_DATA05
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D6__NAND_DATA06
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D7__NAND_DATA07
> > 0xb0b1
> > + MX6QDL_PAD_SD4_DAT0__NAND_DQS
> > 0x00b1
> > + >;
> > + };
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA
> > 0x4001b8b1
> > + MX6QDL_PAD_KEY_COL3__I2C2_SCL
> > 0x4001b8b1
> > + >;
> > + };
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__I2C3_SCL
> > 0x4001b8b1
> > + MX6QDL_PAD_GPIO_16__I2C3_SDA
> > 0x4001b8b1
> > + >;
> > + };
> > + pinctrl_i2c3_gpio: i2c3gpiogrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__GPIO1_IO05
> > 0x4001b8b1
> > + MX6QDL_PAD_GPIO_16__GPIO7_IO11
> > 0x4001b8b1
> > + >;
> > + };
> > + pinctrl_weim_cs: weim_csgrp {
>
> weimcsgrp
No underscore. OK.
>
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_CS0__EIM_CS0_B
> > 0xb0b1
> > + MX6QDL_PAD_EIM_CS1__EIM_CS1_B
> > 0xb0b1
> > + >;
> > + };
> > + pinctrl_weim_fpga: weim_fpgagrp {
>
> weimfpgagrp
No underscore. OK.
...
Thanks,
^ permalink raw reply [flat|nested] 32+ messages in thread* [PATCH 2/2] ARM: dts: Add dts for Uniwest evi
@ 2016-02-02 21:21 ` Joshua Clayton
0 siblings, 0 replies; 32+ messages in thread
From: Joshua Clayton @ 2016-02-02 21:21 UTC (permalink / raw)
To: linux-arm-kernel
Shawn,
thanks for the review.
I've tried to address your concerns.
I have a new dts which I will send once I've booted it.
On Mon, 1 Feb 2016 20:11:45 +0800
Shawn Guo <shawnguo@kernel.org> wrote:
...
> > + regulators {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + reg_usbh1_vbus: regulator at 0 {
> > + compatible = "regulator-fixed";
> > + reg = <0>;
> > + regulator-name = "usbh1_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + enable-active-high;
> > + startup-delay-us = <2>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbh1_hubreset>;
> > + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
> > + };
>
> Device tree maintainers do not like the fake simple-bus container for
> these fixed regulators. We are asked to put them directly under root
> node. In that case, we do not need the artificial 'reg' property, and
> we can name node in schema like:
>
> reg_xxx: regulator-xxx {
> ...
> }
>
OK. will do.
> > +
> > + reg_usb_otg_vbus: regulator at 1 {
> > + compatible = "regulator-fixed";
> > + reg = <1>;
> > + regulator-name = "usb_otg_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg_vbus>;
> > + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + };
> > + };
>
> Have a new line between nodes.
OK.
>
> > + chosen {
> > + bootargs = "sbs-battery.force_load=1";
> > + };
>
> We generally put 'chosen' node at the beginning along with 'memory'
> node. And do we really need this as the default bootargs?
It is needed because if the battery is not installed at boot time,
the device fails to probe as the dts is being parsed, and there is
no way for the kernel to be made aware later.
I guess I could put this into uboot kernel args instead...
I'll remove it for now.
> > +
> > + panel {
> > + compatible = "sharp,lq101k1ly04";
>
> Undocumented compatible string.
This is making its way through the drm list. Its a simple-panel
compatible set of timings.
>
> > +
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&lvds0_out>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&ecspi1 {
> > + fsl,spi-num-chipselects = <1>;
> > + cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_extra>;
>
> You use only one GPIO in cs-gpios. Why do you need to set up 3 in
> pinctrl_ecspi1_extra? And why do you name the pinctrl group in the
> same way as ecspi3 and ecspi5, i.e. pinctrl_ecspi1_cs?
There is only 1 chip select for this spi node.
The extra pins are related to a not-yet-upstreamed driver.
I'll remove them and call it pinctrl_ecspi1_cs
>
> > + status = "okay";
> > +};
> > +
> > +&ecspi3 {
> > + fsl,spi-num-chipselects = <3>;
> > + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
> > + <&gpio4 25 GPIO_ACTIVE_LOW>,
> > + <&gpio4 26 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs>;
> > + status = "okay";
> > +};
> > +
> > +&ecspi5 {
> > + fsl,spi-num-chipselects = <4>;
> > + cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
> > + <&gpio1 13 GPIO_ACTIVE_LOW>,
> > + <&gpio1 12 GPIO_ACTIVE_LOW>,
> > + <&gpio2 9 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5_cs>;
> > + status = "okay";
>
> Have a new line between properties and sub-node.
Will do. Thanks.
>
> > + eeprom: m95m02 at 1 {
> > + compatible = "st,m95m02", "atmel,at25";
> > + size = <262144>;
> > + pagesize = <256>;
> > + address-width = <24>;
> > + spi-max-frequency = <5000000>;
> > + reg = <1>;
> > + };
>
> Have a new line between nodes.
OK.
>
> > + pb_rtc: rtc at 3 {
> > + compatible = "nxp,rtc-pcf2123";
> > + spi-max-frequency = <2450000>;
> > + spi-cs-high;
> > + reg = <3>;
> > + };
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rgmii";
> > + phy-reset-gpios = <&gpio1 25 0>;
> > + status = "okay";
> > +};
> > +
> > +&gpmi {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_gpmi_nand>;
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + clock-frequency = <100000>;
> > + status = "okay";
> > +};
> > +
> > +&i2c3 {
> > + pinctrl-names = "default", "gpio";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + pinctrl-1 = <&pinctrl_i2c3_gpio>;
> > + clock-frequency = <100000>;
> > + status = "okay";
>
> We generally put 'status' at the bottom of the property list.
Will move it.
>
> > + scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
> > + sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
> > +
> > + battery: sbs-battery at b {
> > + compatible = "sbs,sbs-battery";
> > + reg = <0x0b>;
> > + sbs,poll-retry-count = <100>;
> > + sbs,i2c-retry-count = <100>;
> > + };
> > +};
> > +
> > +&ldb {
> > + status = "okay";
> > +
> > + lvds0: lvds-channel at 0 {
> > + fsl,data-mapping = "jeida";
> > + fsl,data-width = <24>;
> > + status = "okay";
> > +
> > + port at 4 {
> > + reg = <4>;
> > +
> > + lvds0_out: endpoint {
> > + remote-endpoint = <&panel_in>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&ssi1 {
> > + fsl,mode = "i2s-slave";
>
> "i2s-slave" is deprecated for fsl,mode, and can be just dropped.
OK.
>
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart2>;
> > + status = "okay";
> > +};
> > +
> > +&usbh1 {
> > + vbus-supply = <®_usbh1_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbh1>;
> > + dr_mode = "host";
> > + disable-over-current;
> > + status = "okay";
> > +};
> > +
> > +&usbotg {
> > + vbus-supply = <®_usb_otg_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg>;
> > + disable-over-current;
> > + dr_mode = "otg";
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&weim {
> > + #address-cells = <2>;
> > + #size-cells = <1>;
> > + ranges = <0 0 0x08000000 0x08000000>;
> > + fsl,weim-cs-gpr = <&gpr>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_weim_fpga &pinctrl_weim_cs>;
> > + status = "okay";
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hog>;
> > +
> > + imx6q-evi {
>
> Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without
> function nodes), this additional container node can just be saved.
So these should be directly under iomux... ok. Will do
>
> > + pinctrl_hog: hoggrp {
> > + fsl,pins = <
> > + /* CPLD Reset */
> > + MX6QDL_PAD_GPIO_19__GPIO4_IO05
> > 0x1b0b0
> > + /* pwr mcu alert irq */
> > + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10
> > 0x1b0b0
> > + /* remainder ???? */
> > + MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19
> > 0x1b0b0
> > + >;
> > + };
>
> Have a new line between nodes.
OK.
>
> > + pinctrl_ecspi1: ecspi1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL1__ECSPI1_MISO
> > 0x100b1
> > + MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI
> > 0x100b1
> > + MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK
> > 0x100b1
> > + >;
> > + };
> > + pinctrl_ecspi1_extra: ecspi1extragrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL2__GPIO4_IO10
> > 0x1b0b0
> > + MX6QDL_PAD_KEY_ROW1__GPIO4_IO09
> > 0x1b0b0
> > + MX6QDL_PAD_KEY_ROW2__GPIO4_IO11
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_ecspi3: ecspi3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK
> > 0x10068
> > + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI
> > 0x10068
> > + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO
> > 0x1f068
> > + >;
> > + };
> > + pinctrl_ecspi3_cs: ecspi3cs {
>
> Please name the node consistently, like xxxgrp.
OK.
>
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24
> > 0x1b0b0
> > + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25
> > 0x1b0b0
> > + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26
> > 0x1b0b0
> > + MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_ecspi5: ecspi5grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK
> > 0x100b1
> > + MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI
> > 0x100b1
> > + MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO
> > 0x100b1
> > + >;
> > + };
> > + pinctrl_ecspi5_cs: ecspi5cs {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_DAT1__GPIO1_IO14
> > 0x1b0b0
> > + MX6QDL_PAD_SD2_DAT2__GPIO1_IO13
> > 0x1b0b0
> > + MX6QDL_PAD_SD2_DAT3__GPIO1_IO12
> > 0x1b0b0
> > + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_enet: enetgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO
> > 0x1b0b0
> > + MX6QDL_PAD_ENET_MDC__ENET_MDC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3
> > 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> > +
> > MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3
> > 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> > + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN
> > 0x4001b0a8
> > + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_gpmi_nand: gpminandgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_CLE__NAND_CLE
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_ALE__NAND_ALE
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_RB0__NAND_READY_B
> > 0xb000
> > + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B
> > 0xb0b1
> > + MX6QDL_PAD_SD4_CMD__NAND_RE_B
> > 0xb0b1
> > + MX6QDL_PAD_SD4_CLK__NAND_WE_B
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D0__NAND_DATA00
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D1__NAND_DATA01
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D2__NAND_DATA02
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D3__NAND_DATA03
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D4__NAND_DATA04
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D5__NAND_DATA05
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D6__NAND_DATA06
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D7__NAND_DATA07
> > 0xb0b1
> > + MX6QDL_PAD_SD4_DAT0__NAND_DQS
> > 0x00b1
> > + >;
> > + };
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA
> > 0x4001b8b1
> > + MX6QDL_PAD_KEY_COL3__I2C2_SCL
> > 0x4001b8b1
> > + >;
> > + };
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__I2C3_SCL
> > 0x4001b8b1
> > + MX6QDL_PAD_GPIO_16__I2C3_SDA
> > 0x4001b8b1
> > + >;
> > + };
> > + pinctrl_i2c3_gpio: i2c3gpiogrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__GPIO1_IO05
> > 0x4001b8b1
> > + MX6QDL_PAD_GPIO_16__GPIO7_IO11
> > 0x4001b8b1
> > + >;
> > + };
> > + pinctrl_weim_cs: weim_csgrp {
>
> weimcsgrp
No underscore. OK.
>
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_CS0__EIM_CS0_B
> > 0xb0b1
> > + MX6QDL_PAD_EIM_CS1__EIM_CS1_B
> > 0xb0b1
> > + >;
> > + };
> > + pinctrl_weim_fpga: weim_fpgagrp {
>
> weimfpgagrp
No underscore. OK.
...
Thanks,
^ permalink raw reply [flat|nested] 32+ messages in thread* Re: [PATCH 2/2] ARM: dts: Add dts for Uniwest evi
@ 2016-02-02 21:21 ` Joshua Clayton
0 siblings, 0 replies; 32+ messages in thread
From: Joshua Clayton @ 2016-02-02 21:21 UTC (permalink / raw)
To: Shawn Guo
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, Sascha Hauer, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Shawn,
thanks for the review.
I've tried to address your concerns.
I have a new dts which I will send once I've booted it.
On Mon, 1 Feb 2016 20:11:45 +0800
Shawn Guo <shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> wrote:
...
> > + regulators {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + reg_usbh1_vbus: regulator@0 {
> > + compatible = "regulator-fixed";
> > + reg = <0>;
> > + regulator-name = "usbh1_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + enable-active-high;
> > + startup-delay-us = <2>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbh1_hubreset>;
> > + gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
> > + };
>
> Device tree maintainers do not like the fake simple-bus container for
> these fixed regulators. We are asked to put them directly under root
> node. In that case, we do not need the artificial 'reg' property, and
> we can name node in schema like:
>
> reg_xxx: regulator-xxx {
> ...
> }
>
OK. will do.
> > +
> > + reg_usb_otg_vbus: regulator@1 {
> > + compatible = "regulator-fixed";
> > + reg = <1>;
> > + regulator-name = "usb_otg_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg_vbus>;
> > + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + regulator-always-on;
> > + };
> > + };
>
> Have a new line between nodes.
OK.
>
> > + chosen {
> > + bootargs = "sbs-battery.force_load=1";
> > + };
>
> We generally put 'chosen' node at the beginning along with 'memory'
> node. And do we really need this as the default bootargs?
It is needed because if the battery is not installed at boot time,
the device fails to probe as the dts is being parsed, and there is
no way for the kernel to be made aware later.
I guess I could put this into uboot kernel args instead...
I'll remove it for now.
> > +
> > + panel {
> > + compatible = "sharp,lq101k1ly04";
>
> Undocumented compatible string.
This is making its way through the drm list. Its a simple-panel
compatible set of timings.
>
> > +
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&lvds0_out>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&ecspi1 {
> > + fsl,spi-num-chipselects = <1>;
> > + cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_extra>;
>
> You use only one GPIO in cs-gpios. Why do you need to set up 3 in
> pinctrl_ecspi1_extra? And why do you name the pinctrl group in the
> same way as ecspi3 and ecspi5, i.e. pinctrl_ecspi1_cs?
There is only 1 chip select for this spi node.
The extra pins are related to a not-yet-upstreamed driver.
I'll remove them and call it pinctrl_ecspi1_cs
>
> > + status = "okay";
> > +};
> > +
> > +&ecspi3 {
> > + fsl,spi-num-chipselects = <3>;
> > + cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
> > + <&gpio4 25 GPIO_ACTIVE_LOW>,
> > + <&gpio4 26 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs>;
> > + status = "okay";
> > +};
> > +
> > +&ecspi5 {
> > + fsl,spi-num-chipselects = <4>;
> > + cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
> > + <&gpio1 13 GPIO_ACTIVE_LOW>,
> > + <&gpio1 12 GPIO_ACTIVE_LOW>,
> > + <&gpio2 9 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5_cs>;
> > + status = "okay";
>
> Have a new line between properties and sub-node.
Will do. Thanks.
>
> > + eeprom: m95m02@1 {
> > + compatible = "st,m95m02", "atmel,at25";
> > + size = <262144>;
> > + pagesize = <256>;
> > + address-width = <24>;
> > + spi-max-frequency = <5000000>;
> > + reg = <1>;
> > + };
>
> Have a new line between nodes.
OK.
>
> > + pb_rtc: rtc@3 {
> > + compatible = "nxp,rtc-pcf2123";
> > + spi-max-frequency = <2450000>;
> > + spi-cs-high;
> > + reg = <3>;
> > + };
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rgmii";
> > + phy-reset-gpios = <&gpio1 25 0>;
> > + status = "okay";
> > +};
> > +
> > +&gpmi {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_gpmi_nand>;
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + clock-frequency = <100000>;
> > + status = "okay";
> > +};
> > +
> > +&i2c3 {
> > + pinctrl-names = "default", "gpio";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + pinctrl-1 = <&pinctrl_i2c3_gpio>;
> > + clock-frequency = <100000>;
> > + status = "okay";
>
> We generally put 'status' at the bottom of the property list.
Will move it.
>
> > + scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
> > + sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
> > +
> > + battery: sbs-battery@b {
> > + compatible = "sbs,sbs-battery";
> > + reg = <0x0b>;
> > + sbs,poll-retry-count = <100>;
> > + sbs,i2c-retry-count = <100>;
> > + };
> > +};
> > +
> > +&ldb {
> > + status = "okay";
> > +
> > + lvds0: lvds-channel@0 {
> > + fsl,data-mapping = "jeida";
> > + fsl,data-width = <24>;
> > + status = "okay";
> > +
> > + port@4 {
> > + reg = <4>;
> > +
> > + lvds0_out: endpoint {
> > + remote-endpoint = <&panel_in>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&ssi1 {
> > + fsl,mode = "i2s-slave";
>
> "i2s-slave" is deprecated for fsl,mode, and can be just dropped.
OK.
>
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart2>;
> > + status = "okay";
> > +};
> > +
> > +&usbh1 {
> > + vbus-supply = <®_usbh1_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbh1>;
> > + dr_mode = "host";
> > + disable-over-current;
> > + status = "okay";
> > +};
> > +
> > +&usbotg {
> > + vbus-supply = <®_usb_otg_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg>;
> > + disable-over-current;
> > + dr_mode = "otg";
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&weim {
> > + #address-cells = <2>;
> > + #size-cells = <1>;
> > + ranges = <0 0 0x08000000 0x08000000>;
> > + fsl,weim-cs-gpr = <&gpr>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_weim_fpga &pinctrl_weim_cs>;
> > + status = "okay";
> > +};
> > +
> > +&iomuxc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hog>;
> > +
> > + imx6q-evi {
>
> Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without
> function nodes), this additional container node can just be saved.
So these should be directly under iomux... ok. Will do
>
> > + pinctrl_hog: hoggrp {
> > + fsl,pins = <
> > + /* CPLD Reset */
> > + MX6QDL_PAD_GPIO_19__GPIO4_IO05
> > 0x1b0b0
> > + /* pwr mcu alert irq */
> > + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10
> > 0x1b0b0
> > + /* remainder ???? */
> > + MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19
> > 0x1b0b0
> > + >;
> > + };
>
> Have a new line between nodes.
OK.
>
> > + pinctrl_ecspi1: ecspi1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL1__ECSPI1_MISO
> > 0x100b1
> > + MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI
> > 0x100b1
> > + MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK
> > 0x100b1
> > + >;
> > + };
> > + pinctrl_ecspi1_extra: ecspi1extragrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL2__GPIO4_IO10
> > 0x1b0b0
> > + MX6QDL_PAD_KEY_ROW1__GPIO4_IO09
> > 0x1b0b0
> > + MX6QDL_PAD_KEY_ROW2__GPIO4_IO11
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_ecspi3: ecspi3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK
> > 0x10068
> > + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI
> > 0x10068
> > + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO
> > 0x1f068
> > + >;
> > + };
> > + pinctrl_ecspi3_cs: ecspi3cs {
>
> Please name the node consistently, like xxxgrp.
OK.
>
> > + fsl,pins = <
> > + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24
> > 0x1b0b0
> > + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25
> > 0x1b0b0
> > + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26
> > 0x1b0b0
> > + MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_ecspi5: ecspi5grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK
> > 0x100b1
> > + MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI
> > 0x100b1
> > + MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO
> > 0x100b1
> > + >;
> > + };
> > + pinctrl_ecspi5_cs: ecspi5cs {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_DAT1__GPIO1_IO14
> > 0x1b0b0
> > + MX6QDL_PAD_SD2_DAT2__GPIO1_IO13
> > 0x1b0b0
> > + MX6QDL_PAD_SD2_DAT3__GPIO1_IO12
> > 0x1b0b0
> > + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_enet: enetgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO
> > 0x1b0b0
> > + MX6QDL_PAD_ENET_MDC__ENET_MDC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3
> > 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> > +
> > MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2
> > 0x1b0b0
> > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3
> > 0x1b0b0
> > +
> > MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> > + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN
> > 0x4001b0a8
> > + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25
> > 0x1b0b0
> > + >;
> > + };
> > + pinctrl_gpmi_nand: gpminandgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_CLE__NAND_CLE
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_ALE__NAND_ALE
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_RB0__NAND_READY_B
> > 0xb000
> > + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B
> > 0xb0b1
> > + MX6QDL_PAD_SD4_CMD__NAND_RE_B
> > 0xb0b1
> > + MX6QDL_PAD_SD4_CLK__NAND_WE_B
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D0__NAND_DATA00
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D1__NAND_DATA01
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D2__NAND_DATA02
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D3__NAND_DATA03
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D4__NAND_DATA04
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D5__NAND_DATA05
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D6__NAND_DATA06
> > 0xb0b1
> > + MX6QDL_PAD_NANDF_D7__NAND_DATA07
> > 0xb0b1
> > + MX6QDL_PAD_SD4_DAT0__NAND_DQS
> > 0x00b1
> > + >;
> > + };
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA
> > 0x4001b8b1
> > + MX6QDL_PAD_KEY_COL3__I2C2_SCL
> > 0x4001b8b1
> > + >;
> > + };
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__I2C3_SCL
> > 0x4001b8b1
> > + MX6QDL_PAD_GPIO_16__I2C3_SDA
> > 0x4001b8b1
> > + >;
> > + };
> > + pinctrl_i2c3_gpio: i2c3gpiogrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__GPIO1_IO05
> > 0x4001b8b1
> > + MX6QDL_PAD_GPIO_16__GPIO7_IO11
> > 0x4001b8b1
> > + >;
> > + };
> > + pinctrl_weim_cs: weim_csgrp {
>
> weimcsgrp
No underscore. OK.
>
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_CS0__EIM_CS0_B
> > 0xb0b1
> > + MX6QDL_PAD_EIM_CS1__EIM_CS1_B
> > 0xb0b1
> > + >;
> > + };
> > + pinctrl_weim_fpga: weim_fpgagrp {
>
> weimfpgagrp
No underscore. OK.
...
Thanks,
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v2] ARM: dts: Add dts for Uniwest evi
@ 2016-02-02 22:13 ` Joshua Clayton
0 siblings, 0 replies; 32+ messages in thread
From: Joshua Clayton @ 2016-02-02 22:13 UTC (permalink / raw)
To: Shawn Guo, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Russell King, Sascha Hauer
Cc: devicetree, linux-arm-kernel, linux-kernel, Joshua Clayton
Uniwest evi is a portable electrical eddy current non-destructive
testing device.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-evi.dts | 506 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 507 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-evi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c4f42a78..4a4ef29 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-cubox-i.dtb \
imx6q-dfi-fs700-m60.dtb \
imx6q-dmo-edmqmx6.dtb \
+ imx6q-evi.dtb \
imx6q-gk802.dtb \
imx6q-gw51xx.dtb \
imx6q-gw52xx.dtb \
diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
new file mode 100644
index 0000000..10f566e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-evi.dts
@@ -0,0 +1,506 @@
+/*
+ * Copyright 2016 United Western Technologies.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Uniwest Evi";
+ compatible = "uniwest,imx6q-evi", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ reg_usbh1_vbus: regulator-usbhubreset {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ startup-delay-us = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_hubreset>;
+ gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotgvbus>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ panel {
+ compatible = "sharp,lq101k1ly04";
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1cs>;
+ status = "okay";
+};
+
+&ecspi3 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
+ <&gpio4 25 GPIO_ACTIVE_LOW>,
+ <&gpio4 26 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3cs>;
+ status = "okay";
+};
+
+&ecspi5 {
+ fsl,spi-num-chipselects = <4>;
+ cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
+ <&gpio1 13 GPIO_ACTIVE_LOW>,
+ <&gpio1 12 GPIO_ACTIVE_LOW>,
+ <&gpio2 9 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5cs>;
+ status = "okay";
+
+ eeprom: m95m02@1 {
+ compatible = "st,m95m02", "atmel,at25";
+ size = <262144>;
+ pagesize = <256>;
+ address-width = <24>;
+ spi-max-frequency = <5000000>;
+ reg = <1>;
+ };
+
+ pb_rtc: rtc@3 {
+ compatible = "nxp,rtc-pcf2123";
+ spi-max-frequency = <2450000>;
+ spi-cs-high;
+ reg = <3>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 0>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpminand>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ clock-frequency = <100000>;
+ scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ battery: sbs-battery@b {
+ compatible = "sbs,sbs-battery";
+ reg = <0x0b>;
+ sbs,poll-retry-count = <100>;
+ sbs,i2c-retry-count = <100>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ fsl,data-mapping = "jeida";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usbh1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ non-removable;
+ status = "okay";
+};
+
+&weim {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>;
+ fsl,weim-cs-gpr = <&gpr>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_weimfpga &pinctrl_weimcs>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* CPLD Reset */
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
+ /* pwr mcu alert irq */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* remainder ???? */
+ MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi1cs: ecspi1csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x10068
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x10068
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x1f068
+ >;
+ };
+
+ pinctrl_ecspi3cs: ecspi3csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi5: ecspi5grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK 0x100b1
+ MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI 0x100b1
+ MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi5cs: ecspi5csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x1b0b0
+ MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x4001b0a8
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpminand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001b8b1
+ >;
+ };
+
+ pinctrl_weimcs: weimcsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
+ MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1
+ >;
+ };
+
+ pinctrl_weimfpga: weimfpgagrp {
+ fsl,pins = <
+ /* weim misc */
+ MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
+ MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
+ MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+ MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0b1
+ MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0b1
+ MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0xb0b1
+ MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0xb0b1
+ MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0xb0b1
+ MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0xb0b1
+ /* weim data */
+ MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x1b0b0
+ MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+ MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+ MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+ MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+ MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+ MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+ MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+ MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+ MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+ MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+ MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+ MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+ MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+ MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+ MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+ MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+ /* weim address */
+ MX6QDL_PAD_EIM_A25__EIM_ADDR25 0xb0b1
+ MX6QDL_PAD_EIM_A24__EIM_ADDR24 0xb0b1
+ MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+ MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+ MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+ MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+ MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+ MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+ MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+ MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+ MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
+ MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
+ MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
+ MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
+ MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
+ MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
+ MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
+ MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
+ MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
+ MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
+ MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
+ MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
+ MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
+ MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
+ MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
+ MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0
+ /* usbh1_b OC */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbh1_hubreset: usbh1hubresetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotgvbus: usbotgvbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ >;
+ };
+};
--
2.5.0
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v2] ARM: dts: Add dts for Uniwest evi
@ 2016-02-02 22:13 ` Joshua Clayton
0 siblings, 0 replies; 32+ messages in thread
From: Joshua Clayton @ 2016-02-02 22:13 UTC (permalink / raw)
To: linux-arm-kernel
Uniwest evi is a portable electrical eddy current non-destructive
testing device.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-evi.dts | 506 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 507 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-evi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c4f42a78..4a4ef29 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-cubox-i.dtb \
imx6q-dfi-fs700-m60.dtb \
imx6q-dmo-edmqmx6.dtb \
+ imx6q-evi.dtb \
imx6q-gk802.dtb \
imx6q-gw51xx.dtb \
imx6q-gw52xx.dtb \
diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
new file mode 100644
index 0000000..10f566e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-evi.dts
@@ -0,0 +1,506 @@
+/*
+ * Copyright 2016 United Western Technologies.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Uniwest Evi";
+ compatible = "uniwest,imx6q-evi", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ reg_usbh1_vbus: regulator-usbhubreset {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ startup-delay-us = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_hubreset>;
+ gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotgvbus>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ panel {
+ compatible = "sharp,lq101k1ly04";
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1cs>;
+ status = "okay";
+};
+
+&ecspi3 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
+ <&gpio4 25 GPIO_ACTIVE_LOW>,
+ <&gpio4 26 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3cs>;
+ status = "okay";
+};
+
+&ecspi5 {
+ fsl,spi-num-chipselects = <4>;
+ cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
+ <&gpio1 13 GPIO_ACTIVE_LOW>,
+ <&gpio1 12 GPIO_ACTIVE_LOW>,
+ <&gpio2 9 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5cs>;
+ status = "okay";
+
+ eeprom: m95m02 at 1 {
+ compatible = "st,m95m02", "atmel,at25";
+ size = <262144>;
+ pagesize = <256>;
+ address-width = <24>;
+ spi-max-frequency = <5000000>;
+ reg = <1>;
+ };
+
+ pb_rtc: rtc at 3 {
+ compatible = "nxp,rtc-pcf2123";
+ spi-max-frequency = <2450000>;
+ spi-cs-high;
+ reg = <3>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 0>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpminand>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ clock-frequency = <100000>;
+ scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ battery: sbs-battery at b {
+ compatible = "sbs,sbs-battery";
+ reg = <0x0b>;
+ sbs,poll-retry-count = <100>;
+ sbs,i2c-retry-count = <100>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel at 0 {
+ fsl,data-mapping = "jeida";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port at 4 {
+ reg = <4>;
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usbh1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ non-removable;
+ status = "okay";
+};
+
+&weim {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>;
+ fsl,weim-cs-gpr = <&gpr>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_weimfpga &pinctrl_weimcs>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* CPLD Reset */
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
+ /* pwr mcu alert irq */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* remainder ???? */
+ MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi1cs: ecspi1csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x10068
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x10068
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x1f068
+ >;
+ };
+
+ pinctrl_ecspi3cs: ecspi3csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi5: ecspi5grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK 0x100b1
+ MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI 0x100b1
+ MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi5cs: ecspi5csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x1b0b0
+ MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x4001b0a8
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpminand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001b8b1
+ >;
+ };
+
+ pinctrl_weimcs: weimcsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
+ MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1
+ >;
+ };
+
+ pinctrl_weimfpga: weimfpgagrp {
+ fsl,pins = <
+ /* weim misc */
+ MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
+ MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
+ MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+ MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0b1
+ MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0b1
+ MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0xb0b1
+ MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0xb0b1
+ MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0xb0b1
+ MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0xb0b1
+ /* weim data */
+ MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x1b0b0
+ MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+ MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+ MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+ MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+ MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+ MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+ MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+ MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+ MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+ MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+ MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+ MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+ MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+ MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+ MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+ MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+ /* weim address */
+ MX6QDL_PAD_EIM_A25__EIM_ADDR25 0xb0b1
+ MX6QDL_PAD_EIM_A24__EIM_ADDR24 0xb0b1
+ MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+ MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+ MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+ MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+ MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+ MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+ MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+ MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+ MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
+ MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
+ MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
+ MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
+ MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
+ MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
+ MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
+ MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
+ MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
+ MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
+ MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
+ MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
+ MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
+ MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
+ MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
+ MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0
+ /* usbh1_b OC */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbh1_hubreset: usbh1hubresetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotgvbus: usbotgvbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ >;
+ };
+};
--
2.5.0
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v2] ARM: dts: Add dts for Uniwest evi
@ 2016-02-03 9:24 ` Philipp Zabel
0 siblings, 0 replies; 32+ messages in thread
From: Philipp Zabel @ 2016-02-03 9:24 UTC (permalink / raw)
To: Joshua Clayton
Cc: Shawn Guo, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Russell King, Sascha Hauer, devicetree, linux-kernel,
linux-arm-kernel
Hi Joshua,
Am Dienstag, den 02.02.2016, 14:13 -0800 schrieb Joshua Clayton:
> Uniwest evi is a portable electrical eddy current non-destructive
> testing device.
>
> Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-evi.dts | 506 ++++++++++++++++++++++++++++++++++++++++
> 2 files changed, 507 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-evi.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c4f42a78..4a4ef29 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-cubox-i.dtb \
> imx6q-dfi-fs700-m60.dtb \
> imx6q-dmo-edmqmx6.dtb \
> + imx6q-evi.dtb \
> imx6q-gk802.dtb \
> imx6q-gw51xx.dtb \
> imx6q-gw52xx.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
> new file mode 100644
> index 0000000..10f566e
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-evi.dts
> @@ -0,0 +1,506 @@
[...]
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "Uniwest Evi";
> + compatible = "uniwest,imx6q-evi", "fsl,imx6q";
[...]
> + panel {
> + compatible = "sharp,lq101k1ly04";
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +};
[...]
> +&ldb {
> + status = "okay";
> +
> + lvds0: lvds-channel@0 {
> + fsl,data-mapping = "jeida";
> + fsl,data-width = <24>;
The "sharp,lq101k1ly04" panel compatible already specifies the bus
format (it is set to MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA in the
simple-panel entry), these two properties can be removed.
> + status = "okay";
> +
> + port@4 {
> + reg = <4>;
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
[...]
regards
Philipp
^ permalink raw reply [flat|nested] 32+ messages in thread* [PATCH v2] ARM: dts: Add dts for Uniwest evi
@ 2016-02-03 9:24 ` Philipp Zabel
0 siblings, 0 replies; 32+ messages in thread
From: Philipp Zabel @ 2016-02-03 9:24 UTC (permalink / raw)
To: linux-arm-kernel
Hi Joshua,
Am Dienstag, den 02.02.2016, 14:13 -0800 schrieb Joshua Clayton:
> Uniwest evi is a portable electrical eddy current non-destructive
> testing device.
>
> Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-evi.dts | 506 ++++++++++++++++++++++++++++++++++++++++
> 2 files changed, 507 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-evi.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c4f42a78..4a4ef29 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-cubox-i.dtb \
> imx6q-dfi-fs700-m60.dtb \
> imx6q-dmo-edmqmx6.dtb \
> + imx6q-evi.dtb \
> imx6q-gk802.dtb \
> imx6q-gw51xx.dtb \
> imx6q-gw52xx.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
> new file mode 100644
> index 0000000..10f566e
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-evi.dts
> @@ -0,0 +1,506 @@
[...]
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "Uniwest Evi";
> + compatible = "uniwest,imx6q-evi", "fsl,imx6q";
[...]
> + panel {
> + compatible = "sharp,lq101k1ly04";
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +};
[...]
> +&ldb {
> + status = "okay";
> +
> + lvds0: lvds-channel at 0 {
> + fsl,data-mapping = "jeida";
> + fsl,data-width = <24>;
The "sharp,lq101k1ly04" panel compatible already specifies the bus
format (it is set to MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA in the
simple-panel entry), these two properties can be removed.
> + status = "okay";
> +
> + port at 4 {
> + reg = <4>;
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
[...]
regards
Philipp
^ permalink raw reply [flat|nested] 32+ messages in thread* Re: [PATCH v2] ARM: dts: Add dts for Uniwest evi
@ 2016-02-03 9:24 ` Philipp Zabel
0 siblings, 0 replies; 32+ messages in thread
From: Philipp Zabel @ 2016-02-03 9:24 UTC (permalink / raw)
To: Joshua Clayton
Cc: Shawn Guo, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Russell King, Sascha Hauer,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Joshua,
Am Dienstag, den 02.02.2016, 14:13 -0800 schrieb Joshua Clayton:
> Uniwest evi is a portable electrical eddy current non-destructive
> testing device.
>
> Signed-off-by: Joshua Clayton <stillcompiling-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-evi.dts | 506 ++++++++++++++++++++++++++++++++++++++++
> 2 files changed, 507 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-evi.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c4f42a78..4a4ef29 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-cubox-i.dtb \
> imx6q-dfi-fs700-m60.dtb \
> imx6q-dmo-edmqmx6.dtb \
> + imx6q-evi.dtb \
> imx6q-gk802.dtb \
> imx6q-gw51xx.dtb \
> imx6q-gw52xx.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
> new file mode 100644
> index 0000000..10f566e
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-evi.dts
> @@ -0,0 +1,506 @@
[...]
> +/dts-v1/;
> +#include "imx6q.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "Uniwest Evi";
> + compatible = "uniwest,imx6q-evi", "fsl,imx6q";
[...]
> + panel {
> + compatible = "sharp,lq101k1ly04";
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +};
[...]
> +&ldb {
> + status = "okay";
> +
> + lvds0: lvds-channel@0 {
> + fsl,data-mapping = "jeida";
> + fsl,data-width = <24>;
The "sharp,lq101k1ly04" panel compatible already specifies the bus
format (it is set to MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA in the
simple-panel entry), these two properties can be removed.
> + status = "okay";
> +
> + port@4 {
> + reg = <4>;
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +};
[...]
regards
Philipp
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 32+ messages in thread* [PATCH v3] ARM: dts: Add dts for Uniwest evi
@ 2016-02-03 17:37 ` Joshua Clayton
0 siblings, 0 replies; 32+ messages in thread
From: Joshua Clayton @ 2016-02-03 17:37 UTC (permalink / raw)
To: Shawn Guo, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Russell King, Sascha Hauer, Philipp Zabel
Cc: devicetree, linux-kernel, linux-arm-kernel, Joshua Clayton
Uniwest evi is a portable electrical eddy current non-destructive
testing device.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
---
Changes since v2:
- removed fsl,data-mapping and fsl,data-width from lvds0 per Phillip Zabel
- removed MX6QDL_PAD_GPIO_19__GPIO4_IO05 from hoggrp. This pin is
used in a not yet upstreamed input driver.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-evi.dts | 502 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 503 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-evi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c4f42a78..4a4ef29 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-cubox-i.dtb \
imx6q-dfi-fs700-m60.dtb \
imx6q-dmo-edmqmx6.dtb \
+ imx6q-evi.dtb \
imx6q-gk802.dtb \
imx6q-gw51xx.dtb \
imx6q-gw52xx.dtb \
diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
new file mode 100644
index 0000000..4fa5601
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-evi.dts
@@ -0,0 +1,502 @@
+/*
+ * Copyright 2016 United Western Technologies.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Uniwest Evi";
+ compatible = "uniwest,imx6q-evi", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ reg_usbh1_vbus: regulator-usbhubreset {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ startup-delay-us = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_hubreset>;
+ gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotgvbus>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ panel {
+ compatible = "sharp,lq101k1ly04";
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1cs>;
+ status = "okay";
+};
+
+&ecspi3 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
+ <&gpio4 25 GPIO_ACTIVE_LOW>,
+ <&gpio4 26 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3cs>;
+ status = "okay";
+};
+
+&ecspi5 {
+ fsl,spi-num-chipselects = <4>;
+ cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
+ <&gpio1 13 GPIO_ACTIVE_LOW>,
+ <&gpio1 12 GPIO_ACTIVE_LOW>,
+ <&gpio2 9 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5cs>;
+ status = "okay";
+
+ eeprom: m95m02@1 {
+ compatible = "st,m95m02", "atmel,at25";
+ size = <262144>;
+ pagesize = <256>;
+ address-width = <24>;
+ spi-max-frequency = <5000000>;
+ reg = <1>;
+ };
+
+ pb_rtc: rtc@3 {
+ compatible = "nxp,rtc-pcf2123";
+ spi-max-frequency = <2450000>;
+ spi-cs-high;
+ reg = <3>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 0>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpminand>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ clock-frequency = <100000>;
+ scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ battery: sbs-battery@b {
+ compatible = "sbs,sbs-battery";
+ reg = <0x0b>;
+ sbs,poll-retry-count = <100>;
+ sbs,i2c-retry-count = <100>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usbh1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ non-removable;
+ status = "okay";
+};
+
+&weim {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>;
+ fsl,weim-cs-gpr = <&gpr>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_weimfpga &pinctrl_weimcs>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* pwr mcu alert irq */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* remainder ???? */
+ MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi1cs: ecspi1csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x10068
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x10068
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x1f068
+ >;
+ };
+
+ pinctrl_ecspi3cs: ecspi3csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi5: ecspi5grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK 0x100b1
+ MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI 0x100b1
+ MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi5cs: ecspi5csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x1b0b0
+ MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x4001b0a8
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpminand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001b8b1
+ >;
+ };
+
+ pinctrl_weimcs: weimcsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
+ MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1
+ >;
+ };
+
+ pinctrl_weimfpga: weimfpgagrp {
+ fsl,pins = <
+ /* weim misc */
+ MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
+ MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
+ MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+ MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0b1
+ MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0b1
+ MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0xb0b1
+ MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0xb0b1
+ MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0xb0b1
+ MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0xb0b1
+ /* weim data */
+ MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x1b0b0
+ MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+ MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+ MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+ MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+ MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+ MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+ MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+ MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+ MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+ MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+ MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+ MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+ MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+ MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+ MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+ MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+ /* weim address */
+ MX6QDL_PAD_EIM_A25__EIM_ADDR25 0xb0b1
+ MX6QDL_PAD_EIM_A24__EIM_ADDR24 0xb0b1
+ MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+ MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+ MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+ MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+ MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+ MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+ MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+ MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+ MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
+ MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
+ MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
+ MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
+ MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
+ MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
+ MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
+ MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
+ MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
+ MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
+ MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
+ MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
+ MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
+ MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
+ MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
+ MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0
+ /* usbh1_b OC */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbh1_hubreset: usbh1hubresetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotgvbus: usbotgvbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ >;
+ };
+};
--
2.5.0
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v3] ARM: dts: Add dts for Uniwest evi
@ 2016-02-03 17:37 ` Joshua Clayton
0 siblings, 0 replies; 32+ messages in thread
From: Joshua Clayton @ 2016-02-03 17:37 UTC (permalink / raw)
To: linux-arm-kernel
Uniwest evi is a portable electrical eddy current non-destructive
testing device.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
---
Changes since v2:
- removed fsl,data-mapping and fsl,data-width from lvds0 per Phillip Zabel
- removed MX6QDL_PAD_GPIO_19__GPIO4_IO05 from hoggrp. This pin is
used in a not yet upstreamed input driver.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-evi.dts | 502 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 503 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-evi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c4f42a78..4a4ef29 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-cubox-i.dtb \
imx6q-dfi-fs700-m60.dtb \
imx6q-dmo-edmqmx6.dtb \
+ imx6q-evi.dtb \
imx6q-gk802.dtb \
imx6q-gw51xx.dtb \
imx6q-gw52xx.dtb \
diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
new file mode 100644
index 0000000..4fa5601
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-evi.dts
@@ -0,0 +1,502 @@
+/*
+ * Copyright 2016 United Western Technologies.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Uniwest Evi";
+ compatible = "uniwest,imx6q-evi", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ reg_usbh1_vbus: regulator-usbhubreset {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ startup-delay-us = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_hubreset>;
+ gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotgvbus>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ panel {
+ compatible = "sharp,lq101k1ly04";
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1cs>;
+ status = "okay";
+};
+
+&ecspi3 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
+ <&gpio4 25 GPIO_ACTIVE_LOW>,
+ <&gpio4 26 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3cs>;
+ status = "okay";
+};
+
+&ecspi5 {
+ fsl,spi-num-chipselects = <4>;
+ cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
+ <&gpio1 13 GPIO_ACTIVE_LOW>,
+ <&gpio1 12 GPIO_ACTIVE_LOW>,
+ <&gpio2 9 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5cs>;
+ status = "okay";
+
+ eeprom: m95m02 at 1 {
+ compatible = "st,m95m02", "atmel,at25";
+ size = <262144>;
+ pagesize = <256>;
+ address-width = <24>;
+ spi-max-frequency = <5000000>;
+ reg = <1>;
+ };
+
+ pb_rtc: rtc at 3 {
+ compatible = "nxp,rtc-pcf2123";
+ spi-max-frequency = <2450000>;
+ spi-cs-high;
+ reg = <3>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 0>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpminand>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ clock-frequency = <100000>;
+ scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ battery: sbs-battery at b {
+ compatible = "sbs,sbs-battery";
+ reg = <0x0b>;
+ sbs,poll-retry-count = <100>;
+ sbs,i2c-retry-count = <100>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel at 0 {
+ status = "okay";
+
+ port at 4 {
+ reg = <4>;
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usbh1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ non-removable;
+ status = "okay";
+};
+
+&weim {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>;
+ fsl,weim-cs-gpr = <&gpr>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_weimfpga &pinctrl_weimcs>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* pwr mcu alert irq */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* remainder ???? */
+ MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi1cs: ecspi1csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x10068
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x10068
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x1f068
+ >;
+ };
+
+ pinctrl_ecspi3cs: ecspi3csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi5: ecspi5grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK 0x100b1
+ MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI 0x100b1
+ MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi5cs: ecspi5csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x1b0b0
+ MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x4001b0a8
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpminand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001b8b1
+ >;
+ };
+
+ pinctrl_weimcs: weimcsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
+ MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1
+ >;
+ };
+
+ pinctrl_weimfpga: weimfpgagrp {
+ fsl,pins = <
+ /* weim misc */
+ MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
+ MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
+ MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+ MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0b1
+ MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0b1
+ MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0xb0b1
+ MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0xb0b1
+ MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0xb0b1
+ MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0xb0b1
+ /* weim data */
+ MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x1b0b0
+ MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+ MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+ MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+ MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+ MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+ MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+ MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+ MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+ MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+ MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+ MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+ MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+ MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+ MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+ MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+ MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+ /* weim address */
+ MX6QDL_PAD_EIM_A25__EIM_ADDR25 0xb0b1
+ MX6QDL_PAD_EIM_A24__EIM_ADDR24 0xb0b1
+ MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+ MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+ MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+ MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+ MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+ MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+ MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+ MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+ MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
+ MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
+ MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
+ MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
+ MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
+ MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
+ MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
+ MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
+ MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
+ MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
+ MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
+ MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
+ MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
+ MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
+ MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
+ MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0
+ /* usbh1_b OC */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbh1_hubreset: usbh1hubresetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotgvbus: usbotgvbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ >;
+ };
+};
--
2.5.0
^ permalink raw reply related [flat|nested] 32+ messages in thread* [PATCH v3] ARM: dts: Add dts for Uniwest evi
@ 2016-02-03 17:37 ` Joshua Clayton
0 siblings, 0 replies; 32+ messages in thread
From: Joshua Clayton @ 2016-02-03 17:37 UTC (permalink / raw)
To: Shawn Guo, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Kumar Gala, Russell King, Sascha Hauer, Philipp Zabel
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Joshua Clayton
Uniwest evi is a portable electrical eddy current non-destructive
testing device.
Signed-off-by: Joshua Clayton <stillcompiling-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
Changes since v2:
- removed fsl,data-mapping and fsl,data-width from lvds0 per Phillip Zabel
- removed MX6QDL_PAD_GPIO_19__GPIO4_IO05 from hoggrp. This pin is
used in a not yet upstreamed input driver.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-evi.dts | 502 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 503 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-evi.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c4f42a78..4a4ef29 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -326,6 +326,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-cubox-i.dtb \
imx6q-dfi-fs700-m60.dtb \
imx6q-dmo-edmqmx6.dtb \
+ imx6q-evi.dtb \
imx6q-gk802.dtb \
imx6q-gw51xx.dtb \
imx6q-gw52xx.dtb \
diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
new file mode 100644
index 0000000..4fa5601
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-evi.dts
@@ -0,0 +1,502 @@
+/*
+ * Copyright 2016 United Western Technologies.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Uniwest Evi";
+ compatible = "uniwest,imx6q-evi", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ reg_usbh1_vbus: regulator-usbhubreset {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ startup-delay-us = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_hubreset>;
+ gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotgvbus>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ panel {
+ compatible = "sharp,lq101k1ly04";
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1cs>;
+ status = "okay";
+};
+
+&ecspi3 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
+ <&gpio4 25 GPIO_ACTIVE_LOW>,
+ <&gpio4 26 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3cs>;
+ status = "okay";
+};
+
+&ecspi5 {
+ fsl,spi-num-chipselects = <4>;
+ cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>,
+ <&gpio1 13 GPIO_ACTIVE_LOW>,
+ <&gpio1 12 GPIO_ACTIVE_LOW>,
+ <&gpio2 9 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi5 &pinctrl_ecspi5cs>;
+ status = "okay";
+
+ eeprom: m95m02@1 {
+ compatible = "st,m95m02", "atmel,at25";
+ size = <262144>;
+ pagesize = <256>;
+ address-width = <24>;
+ spi-max-frequency = <5000000>;
+ reg = <1>;
+ };
+
+ pb_rtc: rtc@3 {
+ compatible = "nxp,rtc-pcf2123";
+ spi-max-frequency = <2450000>;
+ spi-cs-high;
+ reg = <3>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 0>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpminand>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ clock-frequency = <100000>;
+ scl-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ battery: sbs-battery@b {
+ compatible = "sbs,sbs-battery";
+ reg = <0x0b>;
+ sbs,poll-retry-count = <100>;
+ sbs,i2c-retry-count = <100>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usbh1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ non-removable;
+ status = "okay";
+};
+
+&weim {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>;
+ fsl,weim-cs-gpr = <&gpr>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_weimfpga &pinctrl_weimcs>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* pwr mcu alert irq */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
+ /* remainder ???? */
+ MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi1cs: ecspi1csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x10068
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x10068
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x1f068
+ >;
+ };
+
+ pinctrl_ecspi3cs: ecspi3csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
+ MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi5: ecspi5grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK 0x100b1
+ MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI 0x100b1
+ MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi5cs: ecspi5csgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x1b0b0
+ MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x4001b0a8
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpminand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b8b1
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001b8b1
+ >;
+ };
+
+ pinctrl_weimcs: weimcsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
+ MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0xb0b1
+ >;
+ };
+
+ pinctrl_weimfpga: weimfpgagrp {
+ fsl,pins = <
+ /* weim misc */
+ MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
+ MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
+ MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+ MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0xb0b1
+ MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0xb0b1
+ MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0xb0b1
+ MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0xb0b1
+ MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0xb0b1
+ MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0xb0b1
+ /* weim data */
+ MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x1b0b0
+ MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+ MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+ MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+ MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+ MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+ MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+ MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+ MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+ MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+ MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+ MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+ MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+ MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+ MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+ MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+ MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+ /* weim address */
+ MX6QDL_PAD_EIM_A25__EIM_ADDR25 0xb0b1
+ MX6QDL_PAD_EIM_A24__EIM_ADDR24 0xb0b1
+ MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+ MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+ MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+ MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+ MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+ MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+ MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+ MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+ MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
+ MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
+ MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
+ MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
+ MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
+ MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
+ MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
+ MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
+ MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
+ MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
+ MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
+ MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
+ MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
+ MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
+ MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
+ MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0
+ /* usbh1_b OC */
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbh1_hubreset: usbh1hubresetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotgvbus: usbotgvbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ >;
+ };
+};
--
2.5.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 32+ messages in thread* Re: [PATCH v3] ARM: dts: Add dts for Uniwest evi
@ 2016-02-14 3:28 ` Shawn Guo
0 siblings, 0 replies; 32+ messages in thread
From: Shawn Guo @ 2016-02-14 3:28 UTC (permalink / raw)
To: Joshua Clayton
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, Sascha Hauer, Philipp Zabel, devicetree,
linux-kernel, linux-arm-kernel
On Wed, Feb 03, 2016 at 09:37:45AM -0800, Joshua Clayton wrote:
> Uniwest evi is a portable electrical eddy current non-destructive
> testing device.
>
> Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Applied, thanks.
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v3] ARM: dts: Add dts for Uniwest evi
@ 2016-02-14 3:28 ` Shawn Guo
0 siblings, 0 replies; 32+ messages in thread
From: Shawn Guo @ 2016-02-14 3:28 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Feb 03, 2016 at 09:37:45AM -0800, Joshua Clayton wrote:
> Uniwest evi is a portable electrical eddy current non-destructive
> testing device.
>
> Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Applied, thanks.
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3] ARM: dts: Add dts for Uniwest evi
@ 2016-02-14 3:28 ` Shawn Guo
0 siblings, 0 replies; 32+ messages in thread
From: Shawn Guo @ 2016-02-14 3:28 UTC (permalink / raw)
To: Joshua Clayton
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Russell King, Sascha Hauer, Philipp Zabel,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Wed, Feb 03, 2016 at 09:37:45AM -0800, Joshua Clayton wrote:
> Uniwest evi is a portable electrical eddy current non-destructive
> testing device.
>
> Signed-off-by: Joshua Clayton <stillcompiling-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Applied, thanks.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 32+ messages in thread