[PATCH v5 10/10] HID: rmi: Make hid-rmi a transport driver for synaptics-rmi4

* [PATCH v5 10/10] HID: rmi: Make hid-rmi a transport driver for synaptics-rmi4
@ 2016-02-10 22:26 ` Andrew Duggan
  0 siblings, 0 replies; 2+ messages in thread
From: Andrew Duggan @ 2016-02-10 22:26 UTC (permalink / raw)
  To: linux-input, linux-kernel
  Cc: Andrew Duggan, Dmitry Torokhov, Linus Walleij, Jiri Kosina,
	Benjamin Tissoires, Christopher Heiny, Stephen Chandler Paul,
	Vincent Huang, Chris Healy, Andrey Gusakov

The Synaptics RMI4 driver provides support for RMI4 devices. Instead of
duplicating the RMI4 processing code, make hid-rmi a transport driver
and register it with the Synaptics RMI4 core.

Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
---
 drivers/hid/Kconfig   |   2 +-
 drivers/hid/hid-rmi.c | 891 +++++---------------------------------------------
 2 files changed, 75 insertions(+), 818 deletions(-)

diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig
index 513a16c..9cba717 100644
--- a/drivers/hid/Kconfig
+++ b/drivers/hid/Kconfig
@@ -740,7 +740,7 @@ config HID_SUNPLUS
 
 config HID_RMI
 	tristate "Synaptics RMI4 device support"
-	depends on HID
+	depends on HID && RMI4_CORE
 	---help---
 	Support for Synaptics RMI4 touchpads.
 	Say Y here if you have a Synaptics RMI4 touchpads over i2c-hid or usbhid
diff --git a/drivers/hid/hid-rmi.c b/drivers/hid/hid-rmi.c
index 67cd059..a680222 100644
--- a/drivers/hid/hid-rmi.c
+++ b/drivers/hid/hid-rmi.c
@@ -19,6 +19,7 @@
 #include <linux/slab.h>
 #include <linux/wait.h>
 #include <linux/sched.h>
+#include <linux/rmi.h>
 #include "hid-ids.h"
 
 #define RMI_MOUSE_REPORT_ID		0x01 /* Mouse emulation Report */
@@ -33,9 +34,6 @@
 #define RMI_READ_DATA_PENDING		1
 #define RMI_STARTED			2
 
-#define RMI_SLEEP_NORMAL		0x0
-#define RMI_SLEEP_DEEP_SLEEP		0x1
-
 /* device flags */
 #define RMI_DEVICE			BIT(0)
 #define RMI_DEVICE_HAS_PHYS_BUTTONS	BIT(1)
@@ -54,20 +52,6 @@ enum rmi_mode_type {
 	RMI_MODE_NO_PACKED_ATTN_REPORTS	= 2,
 };
 
-struct rmi_function {
-	unsigned page;			/* page of the function */
-	u16 query_base_addr;		/* base address for queries */
-	u16 command_base_addr;		/* base address for commands */
-	u16 control_base_addr;		/* base address for controls */
-	u16 data_base_addr;		/* base address for datas */
-	unsigned int interrupt_base;	/* cross-function interrupt number
-					 * (uniq in the device)*/
-	unsigned int interrupt_count;	/* number of interrupts */
-	unsigned int report_size;	/* size of a report */
-	unsigned long irq_mask;		/* mask of the interrupts
-					 * (to be applied against ATTN IRQ) */
-};
-
 /**
  * struct rmi_data - stores information for hid communication
  *
@@ -104,6 +88,7 @@ struct rmi_function {
 struct rmi_data {
 	struct mutex page_mutex;
 	int page;
+	struct rmi_transport_dev xport;
 
 	wait_queue_head_t wait;
 
@@ -115,34 +100,10 @@ struct rmi_data {
 
 	unsigned long flags;
 
-	struct rmi_function f01;
-	struct rmi_function f11;
-	struct rmi_function f30;
-
-	unsigned int max_fingers;
-	unsigned int max_x;
-	unsigned int max_y;
-	unsigned int x_size_mm;
-	unsigned int y_size_mm;
-	bool read_f11_ctrl_regs;
-	u8 f11_ctrl_regs[RMI_F11_CTRL_REG_COUNT];
-
-	unsigned int gpio_led_count;
-	unsigned int button_count;
-	unsigned long button_mask;
-	unsigned long button_state_mask;
-
-	struct input_dev *input;
-
 	struct work_struct reset_work;
 	struct hid_device *hdev;
 
 	unsigned long device_flags;
-	unsigned long firmware_id;
-
-	u8 f01_ctrl0;
-	u8 interrupt_enable_mask;
-	bool restore_interrupt_mask;
 };
 
 #define RMI_PAGE(addr) (((addr) >> 8) & 0xff)
@@ -214,10 +175,11 @@ static int rmi_write_report(struct hid_device *hdev, u8 *report, int len)
 	return ret;
 }
 
-static int rmi_read_block(struct hid_device *hdev, u16 addr, void *buf,
-		const int len)
+static int rmi_hid_read_block(struct rmi_transport_dev *xport, u16 addr,
+		void *buf, size_t len)
 {
-	struct rmi_data *data = hid_get_drvdata(hdev);
+	struct rmi_data *data = container_of(xport, struct rmi_data, xport);
+	struct hid_device *hdev = data->hdev;
 	int ret;
 	int bytes_read;
 	int bytes_needed;
@@ -286,15 +248,11 @@ exit:
 	return ret;
 }
 
-static inline int rmi_read(struct hid_device *hdev, u16 addr, void *buf)
+static int rmi_hid_write_block(struct rmi_transport_dev *xport, u16 addr,
+		const void *buf, size_t len)
 {
-	return rmi_read_block(hdev, addr, buf, 1);
-}
-
-static int rmi_write_block(struct hid_device *hdev, u16 addr, void *buf,
-		const int len)
-{
-	struct rmi_data *data = hid_get_drvdata(hdev);
+	struct rmi_data *data = container_of(xport, struct rmi_data, xport);
+	struct hid_device *hdev = data->hdev;
 	int ret;
 
 	mutex_lock(&data->page_mutex);
@@ -326,71 +284,13 @@ exit:
 	return ret;
 }
 
-static inline int rmi_write(struct hid_device *hdev, u16 addr, void *buf)
-{
-	return rmi_write_block(hdev, addr, buf, 1);
-}
-
-static void rmi_f11_process_touch(struct rmi_data *hdata, int slot,
-		u8 finger_state, u8 *touch_data)
-{
-	int x, y, wx, wy;
-	int wide, major, minor;
-	int z;
-
-	input_mt_slot(hdata->input, slot);
-	input_mt_report_slot_state(hdata->input, MT_TOOL_FINGER,
-			finger_state == 0x01);
-	if (finger_state == 0x01) {
-		x = (touch_data[0] << 4) | (touch_data[2] & 0x0F);
-		y = (touch_data[1] << 4) | (touch_data[2] >> 4);
-		wx = touch_data[3] & 0x0F;
-		wy = touch_data[3] >> 4;
-		wide = (wx > wy);
-		major = max(wx, wy);
-		minor = min(wx, wy);
-		z = touch_data[4];
-
-		/* y is inverted */
-		y = hdata->max_y - y;
-
-		input_event(hdata->input, EV_ABS, ABS_MT_POSITION_X, x);
-		input_event(hdata->input, EV_ABS, ABS_MT_POSITION_Y, y);
-		input_event(hdata->input, EV_ABS, ABS_MT_ORIENTATION, wide);
-		input_event(hdata->input, EV_ABS, ABS_MT_PRESSURE, z);
-		input_event(hdata->input, EV_ABS, ABS_MT_TOUCH_MAJOR, major);
-		input_event(hdata->input, EV_ABS, ABS_MT_TOUCH_MINOR, minor);
-	}
-}
-
-static int rmi_reset_attn_mode(struct hid_device *hdev)
-{
-	struct rmi_data *data = hid_get_drvdata(hdev);
-	int ret;
-
-	ret = rmi_set_mode(hdev, RMI_MODE_ATTN_REPORTS);
-	if (ret)
-		return ret;
-
-	if (data->restore_interrupt_mask) {
-		ret = rmi_write(hdev, data->f01.control_base_addr + 1,
-				&data->interrupt_enable_mask);
-		if (ret) {
-			hid_err(hdev, "can not write F01 control register\n");
-			return ret;
-		}
-	}
-
-	return 0;
-}
-
 static void rmi_reset_work(struct work_struct *work)
 {
 	struct rmi_data *hdata = container_of(work, struct rmi_data,
 						reset_work);
 
 	/* switch the device to RMI if we receive a generic mouse report */
-	rmi_reset_attn_mode(hdata->hdev);
+	rmi_set_mode(hdata->hdev, RMI_MODE_ATTN_REPORTS);
 }
 
 static inline int rmi_schedule_reset(struct hid_device *hdev)
@@ -399,96 +299,20 @@ static inline int rmi_schedule_reset(struct hid_device *hdev)
 	return schedule_work(&hdata->reset_work);
 }
 
-static int rmi_f11_input_event(struct hid_device *hdev, u8 irq, u8 *data,
-		int size)
-{
-	struct rmi_data *hdata = hid_get_drvdata(hdev);
-	int offset;
-	int i;
-
-	if (!(irq & hdata->f11.irq_mask) || size <= 0)
-		return 0;
-
-	offset = (hdata->max_fingers >> 2) + 1;
-	for (i = 0; i < hdata->max_fingers; i++) {
-		int fs_byte_position = i >> 2;
-		int fs_bit_position = (i & 0x3) << 1;
-		int finger_state = (data[fs_byte_position] >> fs_bit_position) &
-					0x03;
-		int position = offset + 5 * i;
-
-		if (position + 5 > size) {
-			/* partial report, go on with what we received */
-			printk_once(KERN_WARNING
-				"%s %s: Detected incomplete finger report. Finger reports may occasionally get dropped on this platform.\n",
-				 dev_driver_string(&hdev->dev),
-				 dev_name(&hdev->dev));
-			hid_dbg(hdev, "Incomplete finger report\n");
-			break;
-		}
-
-		rmi_f11_process_touch(hdata, i, finger_state, &data[position]);
-	}
-	input_mt_sync_frame(hdata->input);
-	input_sync(hdata->input);
-	return hdata->f11.report_size;
-}
-
-static int rmi_f30_input_event(struct hid_device *hdev, u8 irq, u8 *data,
-		int size)
-{
-	struct rmi_data *hdata = hid_get_drvdata(hdev);
-	int i;
-	int button = 0;
-	bool value;
-
-	if (!(irq & hdata->f30.irq_mask))
-		return 0;
-
-	if (size < (int)hdata->f30.report_size) {
-		hid_warn(hdev, "Click Button pressed, but the click data is missing\n");
-		return 0;
-	}
-
-	for (i = 0; i < hdata->gpio_led_count; i++) {
-		if (test_bit(i, &hdata->button_mask)) {
-			value = (data[i / 8] >> (i & 0x07)) & BIT(0);
-			if (test_bit(i, &hdata->button_state_mask))
-				value = !value;
-			input_event(hdata->input, EV_KEY, BTN_LEFT + button++,
-					value);
-		}
-	}
-	return hdata->f30.report_size;
-}
-
 static int rmi_input_event(struct hid_device *hdev, u8 *data, int size)
 {
 	struct rmi_data *hdata = hid_get_drvdata(hdev);
-	unsigned long irq_mask = 0;
-	unsigned index = 2;
+	struct rmi_device *rmi_dev = hdata->xport.rmi_dev;
+	struct rmi_driver_data *drvdata = dev_get_drvdata(&rmi_dev->dev);
 
 	if (!(test_bit(RMI_STARTED, &hdata->flags)))
 		return 0;
 
-	irq_mask |= hdata->f11.irq_mask;
-	irq_mask |= hdata->f30.irq_mask;
-
-	if (data[1] & ~irq_mask)
-		hid_dbg(hdev, "unknown intr source:%02lx %s:%d\n",
-			data[1] & ~irq_mask, __FILE__, __LINE__);
-
-	if (hdata->f11.interrupt_base < hdata->f30.interrupt_base) {
-		index += rmi_f11_input_event(hdev, data[1], &data[index],
-				size - index);
-		index += rmi_f30_input_event(hdev, data[1], &data[index],
-				size - index);
-	} else {
-		index += rmi_f30_input_event(hdev, data[1], &data[index],
-				size - index);
-		index += rmi_f11_input_event(hdev, data[1], &data[index],
-				size - index);
-	}
+	*(drvdata->irq_status) = data[1];
+	hdata->xport.attn_data = &data[2];
+	hdata->xport.attn_size = hdata->input_report_size - 2;
+
+	rmi_process_interrupt_requests(rmi_dev);
 
 	return 1;
 }
@@ -570,626 +394,71 @@ static int rmi_event(struct hid_device *hdev, struct hid_field *field,
 }
 
 #ifdef CONFIG_PM
-static int rmi_set_sleep_mode(struct hid_device *hdev, int sleep_mode)
-{
-	struct rmi_data *data = hid_get_drvdata(hdev);
-	int ret;
-	u8 f01_ctrl0;
-
-	f01_ctrl0 = (data->f01_ctrl0 & ~0x3) | sleep_mode;
-
-	ret = rmi_write(hdev, data->f01.control_base_addr,
-			&f01_ctrl0);
-	if (ret) {
-		hid_err(hdev, "can not write sleep mode\n");
-		return ret;
-	}
-
-	return 0;
-}
-
 static int rmi_suspend(struct hid_device *hdev, pm_message_t message)
 {
 	struct rmi_data *data = hid_get_drvdata(hdev);
+	struct rmi_device *rmi_dev = data->xport.rmi_dev;
 	int ret;
-	u8 buf[RMI_F11_CTRL_REG_COUNT];
-
-	ret = rmi_read_block(hdev, data->f11.control_base_addr, buf,
-				RMI_F11_CTRL_REG_COUNT);
-	if (ret)
-		hid_warn(hdev, "can not read F11 control registers\n");
-	else
-		memcpy(data->f11_ctrl_regs, buf, RMI_F11_CTRL_REG_COUNT);
-
-
-	if (!device_may_wakeup(hdev->dev.parent))
-		return rmi_set_sleep_mode(hdev, RMI_SLEEP_DEEP_SLEEP);
-
-	return 0;
-}
-
-static int rmi_post_reset(struct hid_device *hdev)
-{
-	struct rmi_data *data = hid_get_drvdata(hdev);
-	int ret;
-
-	ret = rmi_reset_attn_mode(hdev);
-	if (ret) {
-		hid_err(hdev, "can not set rmi mode\n");
-		return ret;
-	}
-
-	if (data->read_f11_ctrl_regs) {
-		ret = rmi_write_block(hdev, data->f11.control_base_addr,
-				data->f11_ctrl_regs, RMI_F11_CTRL_REG_COUNT);
-		if (ret)
-			hid_warn(hdev,
-				"can not write F11 control registers after reset\n");
-	}
-
-	if (!device_may_wakeup(hdev->dev.parent)) {
-		ret = rmi_set_sleep_mode(hdev, RMI_SLEEP_NORMAL);
-		if (ret) {
-			hid_err(hdev, "can not write sleep mode\n");
-			return ret;
-		}
-	}
-
-	return ret;
-}
-
-static int rmi_post_resume(struct hid_device *hdev)
-{
-	return rmi_reset_attn_mode(hdev);
-}
-#endif /* CONFIG_PM */
-
-#define RMI4_MAX_PAGE 0xff
-#define RMI4_PAGE_SIZE 0x0100
-
-#define PDT_START_SCAN_LOCATION 0x00e9
-#define PDT_END_SCAN_LOCATION	0x0005
-#define RMI4_END_OF_PDT(id) ((id) == 0x00 || (id) == 0xff)
-
-struct pdt_entry {
-	u8 query_base_addr:8;
-	u8 command_base_addr:8;
-	u8 control_base_addr:8;
-	u8 data_base_addr:8;
-	u8 interrupt_source_count:3;
-	u8 bits3and4:2;
-	u8 function_version:2;
-	u8 bit7:1;
-	u8 function_number:8;
-} __attribute__((__packed__));
-
-static inline unsigned long rmi_gen_mask(unsigned irq_base, unsigned irq_count)
-{
-	return GENMASK(irq_count + irq_base - 1, irq_base);
-}
-
-static void rmi_register_function(struct rmi_data *data,
-	struct pdt_entry *pdt_entry, int page, unsigned interrupt_count)
-{
-	struct rmi_function *f = NULL;
-	u16 page_base = page << 8;
-
-	switch (pdt_entry->function_number) {
-	case 0x01:
-		f = &data->f01;
-		break;
-	case 0x11:
-		f = &data->f11;
-		break;
-	case 0x30:
-		f = &data->f30;
-		break;
-	}
-
-	if (f) {
-		f->page = page;
-		f->query_base_addr = page_base | pdt_entry->query_base_addr;
-		f->command_base_addr = page_base | pdt_entry->command_base_addr;
-		f->control_base_addr = page_base | pdt_entry->control_base_addr;
-		f->data_base_addr = page_base | pdt_entry->data_base_addr;
-		f->interrupt_base = interrupt_count;
-		f->interrupt_count = pdt_entry->interrupt_source_count;
-		f->irq_mask = rmi_gen_mask(f->interrupt_base,
-						f->interrupt_count);
-		data->interrupt_enable_mask |= f->irq_mask;
-	}
-}
-
-static int rmi_scan_pdt(struct hid_device *hdev)
-{
-	struct rmi_data *data = hid_get_drvdata(hdev);
-	struct pdt_entry entry;
-	int page;
-	bool page_has_function;
-	int i;
-	int retval;
-	int interrupt = 0;
-	u16 page_start, pdt_start , pdt_end;
-
-	hid_info(hdev, "Scanning PDT...\n");
-
-	for (page = 0; (page <= RMI4_MAX_PAGE); page++) {
-		page_start = RMI4_PAGE_SIZE * page;
-		pdt_start = page_start + PDT_START_SCAN_LOCATION;
-		pdt_end = page_start + PDT_END_SCAN_LOCATION;
-
-		page_has_function = false;
-		for (i = pdt_start; i >= pdt_end; i -= sizeof(entry)) {
-			retval = rmi_read_block(hdev, i, &entry, sizeof(entry));
-			if (retval) {
-				hid_err(hdev,
-					"Read of PDT entry at %#06x failed.\n",
-					i);
-				goto error_exit;
-			}
-
-			if (RMI4_END_OF_PDT(entry.function_number))
-				break;
-
-			page_has_function = true;
-
-			hid_info(hdev, "Found F%02X on page %#04x\n",
-					entry.function_number, page);
-
-			rmi_register_function(data, &entry, page, interrupt);
-			interrupt += entry.interrupt_source_count;
-		}
-
-		if (!page_has_function)
-			break;
-	}
-
-	hid_info(hdev, "%s: Done with PDT scan.\n", __func__);
-	retval = 0;
-
-error_exit:
-	return retval;
-}
-
-#define RMI_DEVICE_F01_BASIC_QUERY_LEN	11
-
-static int rmi_populate_f01(struct hid_device *hdev)
-{
-	struct rmi_data *data = hid_get_drvdata(hdev);
-	u8 basic_queries[RMI_DEVICE_F01_BASIC_QUERY_LEN];
-	u8 info[3];
-	int ret;
-	bool has_query42;
-	bool has_lts;
-	bool has_sensor_id;
-	bool has_ds4_queries = false;
-	bool has_build_id_query = false;
-	bool has_package_id_query = false;
-	u16 query_offset = data->f01.query_base_addr;
-	u16 prod_info_addr;
-	u8 ds4_query_len;
-
-	ret = rmi_read_block(hdev, query_offset, basic_queries,
-				RMI_DEVICE_F01_BASIC_QUERY_LEN);
-	if (ret) {
-		hid_err(hdev, "Can not read basic queries from Function 0x1.\n");
-		return ret;
-	}
-
-	has_lts = !!(basic_queries[0] & BIT(2));
-	has_sensor_id = !!(basic_queries[1] & BIT(3));
-	has_query42 = !!(basic_queries[1] & BIT(7));
-
-	query_offset += 11;
-	prod_info_addr = query_offset + 6;
-	query_offset += 10;
-
-	if (has_lts)
-		query_offset += 20;
-
-	if (has_sensor_id)
-		query_offset++;
-
-	if (has_query42) {
-		ret = rmi_read(hdev, query_offset, info);
-		if (ret) {
-			hid_err(hdev, "Can not read query42.\n");
-			return ret;
-		}
-		has_ds4_queries = !!(info[0] & BIT(0));
-		query_offset++;
-	}
-
-	if (has_ds4_queries) {
-		ret = rmi_read(hdev, query_offset, &ds4_query_len);
-		if (ret) {
-			hid_err(hdev, "Can not read DS4 Query length.\n");
-			return ret;
-		}
-		query_offset++;
-
-		if (ds4_query_len > 0) {
-			ret = rmi_read(hdev, query_offset, info);
-			if (ret) {
-				hid_err(hdev, "Can not read DS4 query.\n");
-				return ret;
-			}
-
-			has_package_id_query = !!(info[0] & BIT(0));
-			has_build_id_query = !!(info[0] & BIT(1));
-		}
-	}
-
-	if (has_package_id_query)
-		prod_info_addr++;
-
-	if (has_build_id_query) {
-		ret = rmi_read_block(hdev, prod_info_addr, info, 3);
-		if (ret) {
-			hid_err(hdev, "Can not read product info.\n");
-			return ret;
-		}
-
-		data->firmware_id = info[1] << 8 | info[0];
-		data->firmware_id += info[2] * 65536;
-	}
-
-	ret = rmi_read_block(hdev, data->f01.control_base_addr, info,
-				2);
-
-	if (ret) {
-		hid_err(hdev, "can not read f01 ctrl registers\n");
-		return ret;
-	}
-
-	data->f01_ctrl0 = info[0];
-
-	if (!info[1]) {
-		/*
-		 * Do to a firmware bug in some touchpads the F01 interrupt
-		 * enable control register will be cleared on reset.
-		 * This will stop the touchpad from reporting data, so
-		 * if F01 CTRL1 is 0 then we need to explicitly enable
-		 * interrupts for the functions we want data for.
-		 */
-		data->restore_interrupt_mask = true;
-
-		ret = rmi_write(hdev, data->f01.control_base_addr + 1,
-				&data->interrupt_enable_mask);
-		if (ret) {
-			hid_err(hdev, "can not write to control reg 1: %d.\n",
-				ret);
-			return ret;
-		}
-	}
-
-	return 0;
-}
-
-static int rmi_populate_f11(struct hid_device *hdev)
-{
-	struct rmi_data *data = hid_get_drvdata(hdev);
-	u8 buf[20];
-	int ret;
-	bool has_query9;
-	bool has_query10 = false;
-	bool has_query11;
-	bool has_query12;
-	bool has_query27;
-	bool has_query28;
-	bool has_query36 = false;
-	bool has_physical_props;
-	bool has_gestures;
-	bool has_rel;
-	bool has_data40 = false;
-	bool has_dribble = false;
-	bool has_palm_detect = false;
-	unsigned x_size, y_size;
-	u16 query_offset;
-
-	if (!data->f11.query_base_addr) {
-		hid_err(hdev, "No 2D sensor found, giving up.\n");
-		return -ENODEV;
-	}
 
-	/* query 0 contains some useful information */
-	ret = rmi_read(hdev, data->f11.query_base_addr, buf);
-	if (ret) {
-		hid_err(hdev, "can not get query 0: %d.\n", ret);
-		return ret;
-	}
-	has_query9 = !!(buf[0] & BIT(3));
-	has_query11 = !!(buf[0] & BIT(4));
-	has_query12 = !!(buf[0] & BIT(5));
-	has_query27 = !!(buf[0] & BIT(6));
-	has_query28 = !!(buf[0] & BIT(7));
-
-	/* query 1 to get the max number of fingers */
-	ret = rmi_read(hdev, data->f11.query_base_addr + 1, buf);
-	if (ret) {
-		hid_err(hdev, "can not get NumberOfFingers: %d.\n", ret);
-		return ret;
-	}
-	data->max_fingers = (buf[0] & 0x07) + 1;
-	if (data->max_fingers > 5)
-		data->max_fingers = 10;
-
-	data->f11.report_size = data->max_fingers * 5 +
-				DIV_ROUND_UP(data->max_fingers, 4);
-
-	if (!(buf[0] & BIT(4))) {
-		hid_err(hdev, "No absolute events, giving up.\n");
-		return -ENODEV;
-	}
-
-	has_rel = !!(buf[0] & BIT(3));
-	has_gestures = !!(buf[0] & BIT(5));
-
-	ret = rmi_read(hdev, data->f11.query_base_addr + 5, buf);
-	if (ret) {
-		hid_err(hdev, "can not get absolute data sources: %d.\n", ret);
-		return ret;
-	}
-
-	has_dribble = !!(buf[0] & BIT(4));
-
-	/*
-	 * At least 4 queries are guaranteed to be present in F11
-	 * +1 for query 5 which is present since absolute events are
-	 * reported and +1 for query 12.
-	 */
-	query_offset = 6;
-
-	if (has_rel)
-		++query_offset; /* query 6 is present */
-
-	if (has_gestures) {
-		/* query 8 to find out if query 10 exists */
-		ret = rmi_read(hdev,
-			data->f11.query_base_addr + query_offset + 1, buf);
-		if (ret) {
-			hid_err(hdev, "can not read gesture information: %d.\n",
-				ret);
-			return ret;
-		}
-		has_palm_detect = !!(buf[0] & BIT(0));
-		has_query10 = !!(buf[0] & BIT(2));
-
-		query_offset += 2; /* query 7 and 8 are present */
-	}
-
-	if (has_query9)
-		++query_offset;
-
-	if (has_query10)
-		++query_offset;
-
-	if (has_query11)
-		++query_offset;
-
-	/* query 12 to know if the physical properties are reported */
-	if (has_query12) {
-		ret = rmi_read(hdev, data->f11.query_base_addr
-				+ query_offset, buf);
-		if (ret) {
-			hid_err(hdev, "can not get query 12: %d.\n", ret);
-			return ret;
-		}
-		has_physical_props = !!(buf[0] & BIT(5));
-
-		if (has_physical_props) {
-			query_offset += 1;
-			ret = rmi_read_block(hdev,
-					data->f11.query_base_addr
-						+ query_offset, buf, 4);
-			if (ret) {
-				hid_err(hdev, "can not read query 15-18: %d.\n",
-					ret);
-				return ret;
-			}
-
-			x_size = buf[0] | (buf[1] << 8);
-			y_size = buf[2] | (buf[3] << 8);
-
-			data->x_size_mm = DIV_ROUND_CLOSEST(x_size, 10);
-			data->y_size_mm = DIV_ROUND_CLOSEST(y_size, 10);
-
-			hid_info(hdev, "%s: size in mm: %d x %d\n",
-				 __func__, data->x_size_mm, data->y_size_mm);
-
-			/*
-			 * query 15 - 18 contain the size of the sensor
-			 * and query 19 - 26 contain bezel dimensions
-			 */
-			query_offset += 12;
-		}
-	}
-
-	if (has_query27)
-		++query_offset;
-
-	if (has_query28) {
-		ret = rmi_read(hdev, data->f11.query_base_addr
-				+ query_offset, buf);
-		if (ret) {
-			hid_err(hdev, "can not get query 28: %d.\n", ret);
-			return ret;
-		}
-
-		has_query36 = !!(buf[0] & BIT(6));
-	}
-
-	if (has_query36) {
-		query_offset += 2;
-		ret = rmi_read(hdev, data->f11.query_base_addr
-				+ query_offset, buf);
-		if (ret) {
-			hid_err(hdev, "can not get query 36: %d.\n", ret);
-			return ret;
-		}
-
-		has_data40 = !!(buf[0] & BIT(5));
-	}
-
-
-	if (has_data40)
-		data->f11.report_size += data->max_fingers * 2;
+	if (!(data->device_flags & RMI_DEVICE))
+		return 0;
 
-	ret = rmi_read_block(hdev, data->f11.control_base_addr,
-			data->f11_ctrl_regs, RMI_F11_CTRL_REG_COUNT);
+	ret = rmi_driver_suspend(rmi_dev);
 	if (ret) {
-		hid_err(hdev, "can not read ctrl block of size 11: %d.\n", ret);
+		hid_warn(hdev, "Failed to suspend device: %d\n", ret);
 		return ret;
 	}
 
-	/* data->f11_ctrl_regs now contains valid register data */
-	data->read_f11_ctrl_regs = true;
-
-	data->max_x = data->f11_ctrl_regs[6] | (data->f11_ctrl_regs[7] << 8);
-	data->max_y = data->f11_ctrl_regs[8] | (data->f11_ctrl_regs[9] << 8);
-
-	if (has_dribble) {
-		data->f11_ctrl_regs[0] = data->f11_ctrl_regs[0] & ~BIT(6);
-		ret = rmi_write(hdev, data->f11.control_base_addr,
-				data->f11_ctrl_regs);
-		if (ret) {
-			hid_err(hdev, "can not write to control reg 0: %d.\n",
-				ret);
-			return ret;
-		}
-	}
-
-	if (has_palm_detect) {
-		data->f11_ctrl_regs[11] = data->f11_ctrl_regs[11] & ~BIT(0);
-		ret = rmi_write(hdev, data->f11.control_base_addr + 11,
-				&data->f11_ctrl_regs[11]);
-		if (ret) {
-			hid_err(hdev, "can not write to control reg 11: %d.\n",
-				ret);
-			return ret;
-		}
-	}
-
 	return 0;
 }
 
-static int rmi_populate_f30(struct hid_device *hdev)
+static int rmi_post_resume(struct hid_device *hdev)
 {
 	struct rmi_data *data = hid_get_drvdata(hdev);
-	u8 buf[20];
+	struct rmi_device *rmi_dev = data->xport.rmi_dev;
 	int ret;
-	bool has_gpio, has_led;
-	unsigned bytes_per_ctrl;
-	u8 ctrl2_addr;
-	int ctrl2_3_length;
-	int i;
 
-	/* function F30 is for physical buttons */
-	if (!data->f30.query_base_addr) {
-		hid_err(hdev, "No GPIO/LEDs found, giving up.\n");
-		return -ENODEV;
-	}
+	if (!(data->device_flags & RMI_DEVICE))
+		return 0;
 
-	ret = rmi_read_block(hdev, data->f30.query_base_addr, buf, 2);
-	if (ret) {
-		hid_err(hdev, "can not get F30 query registers: %d.\n", ret);
+	ret = rmi_set_mode(hdev, RMI_MODE_ATTN_REPORTS);
+	if (ret)
 		return ret;
-	}
-
-	has_gpio = !!(buf[0] & BIT(3));
-	has_led = !!(buf[0] & BIT(2));
-	data->gpio_led_count = buf[1] & 0x1f;
-
-	/* retrieve ctrl 2 & 3 registers */
-	bytes_per_ctrl = (data->gpio_led_count + 7) / 8;
-	/* Ctrl0 is present only if both has_gpio and has_led are set*/
-	ctrl2_addr = (has_gpio && has_led) ? bytes_per_ctrl : 0;
-	/* Ctrl1 is always be present */
-	ctrl2_addr += bytes_per_ctrl;
-	ctrl2_3_length = 2 * bytes_per_ctrl;
 
-	data->f30.report_size = bytes_per_ctrl;
-
-	ret = rmi_read_block(hdev, data->f30.control_base_addr + ctrl2_addr,
-				buf, ctrl2_3_length);
+	ret = rmi_driver_resume(rmi_dev);
 	if (ret) {
-		hid_err(hdev, "can not read ctrl 2&3 block of size %d: %d.\n",
-			ctrl2_3_length, ret);
+		hid_warn(hdev, "Failed to resume device: %d\n", ret);
 		return ret;
 	}
 
-	for (i = 0; i < data->gpio_led_count; i++) {
-		int byte_position = i >> 3;
-		int bit_position = i & 0x07;
-		u8 dir_byte = buf[byte_position];
-		u8 data_byte = buf[byte_position + bytes_per_ctrl];
-		bool dir = (dir_byte >> bit_position) & BIT(0);
-		bool dat = (data_byte >> bit_position) & BIT(0);
-
-		if (dir == 0) {
-			/* input mode */
-			if (dat) {
-				/* actual buttons have pull up resistor */
-				data->button_count++;
-				set_bit(i, &data->button_mask);
-				set_bit(i, &data->button_state_mask);
-			}
-		}
-
-	}
-
 	return 0;
 }
+#endif /* CONFIG_PM */
 
-static int rmi_populate(struct hid_device *hdev)
+static int rmi_hid_reset(struct rmi_transport_dev *xport, u16 reset_addr)
 {
-	struct rmi_data *data = hid_get_drvdata(hdev);
-	int ret;
-
-	ret = rmi_scan_pdt(hdev);
-	if (ret) {
-		hid_err(hdev, "PDT scan failed with code %d.\n", ret);
-		return ret;
-	}
-
-	ret = rmi_populate_f01(hdev);
-	if (ret) {
-		hid_err(hdev, "Error while initializing F01 (%d).\n", ret);
-		return ret;
-	}
-
-	ret = rmi_populate_f11(hdev);
-	if (ret) {
-		hid_err(hdev, "Error while initializing F11 (%d).\n", ret);
-		return ret;
-	}
-
-	if (!(data->device_flags & RMI_DEVICE_HAS_PHYS_BUTTONS)) {
-		ret = rmi_populate_f30(hdev);
-		if (ret)
-			hid_warn(hdev, "Error while initializing F30 (%d).\n", ret);
-	}
+	struct rmi_data *data = container_of(xport, struct rmi_data, xport);
+	struct hid_device *hdev = data->hdev;
 
-	return 0;
+	return rmi_set_mode(hdev, RMI_MODE_ATTN_REPORTS);
 }
 
 static int rmi_input_configured(struct hid_device *hdev, struct hid_input *hi)
 {
 	struct rmi_data *data = hid_get_drvdata(hdev);
 	struct input_dev *input = hi->input;
-	int ret;
-	int res_x, res_y, i;
+	int ret = 0;
+
+	if (!(data->device_flags & RMI_DEVICE))
+		return 0;
 
-	data->input = input;
+	data->xport.input = input;
 
 	hid_dbg(hdev, "Opening low level driver\n");
 	ret = hid_hw_open(hdev);
 	if (ret)
 		return ret;
 
-	if (!(data->device_flags & RMI_DEVICE))
-		return 0;
-
 	/* Allow incoming hid reports */
 	hid_device_io_start(hdev);
 
@@ -1205,40 +474,10 @@ static int rmi_input_configured(struct hid_device *hdev, struct hid_input *hi)
 		goto exit;
 	}
 
-	ret = rmi_populate(hdev);
-	if (ret)
-		goto exit;
-
-	hid_info(hdev, "firmware id: %ld\n", data->firmware_id);
-
-	__set_bit(EV_ABS, input->evbit);
-	input_set_abs_params(input, ABS_MT_POSITION_X, 1, data->max_x, 0, 0);
-	input_set_abs_params(input, ABS_MT_POSITION_Y, 1, data->max_y, 0, 0);
-
-	if (data->x_size_mm && data->y_size_mm) {
-		res_x = (data->max_x - 1) / data->x_size_mm;
-		res_y = (data->max_y - 1) / data->y_size_mm;
-
-		input_abs_set_res(input, ABS_MT_POSITION_X, res_x);
-		input_abs_set_res(input, ABS_MT_POSITION_Y, res_y);
-	}
-
-	input_set_abs_params(input, ABS_MT_ORIENTATION, 0, 1, 0, 0);
-	input_set_abs_params(input, ABS_MT_PRESSURE, 0, 0xff, 0, 0);
-	input_set_abs_params(input, ABS_MT_TOUCH_MAJOR, 0, 0x0f, 0, 0);
-	input_set_abs_params(input, ABS_MT_TOUCH_MINOR, 0, 0x0f, 0, 0);
-
-	ret = input_mt_init_slots(input, data->max_fingers, INPUT_MT_POINTER);
-	if (ret < 0)
+	ret = rmi_register_transport_device(&data->xport);
+	if (ret < 0) {
+		dev_err(&hdev->dev, "failed to register transport driver\n");
 		goto exit;
-
-	if (data->button_count) {
-		__set_bit(EV_KEY, input->evbit);
-		for (i = 0; i < data->button_count; i++)
-			__set_bit(BTN_LEFT + i, input->keybit);
-
-		if (data->button_count == 1)
-			__set_bit(INPUT_PROP_BUTTONPAD, input->propbit);
 	}
 
 	set_bit(RMI_STARTED, &data->flags);
@@ -1287,6 +526,26 @@ static int rmi_check_valid_report_id(struct hid_device *hdev, unsigned type,
 	return 0;
 }
 
+static struct rmi_2d_sensor_platform_data rmi_hid_2d_sensor_data = {
+	.sensor_type = rmi_sensor_touchpad,
+	.axis_align.flip_y = true,
+	.kernel_tracking = true,
+};
+
+static struct rmi_f30_data rmi_hid_f30_data = {
+};
+
+static struct rmi_device_platform_data rmi_hid_pdata = {
+	.sensor_pdata = &rmi_hid_2d_sensor_data,
+	.f30_data = &rmi_hid_f30_data,
+};
+
+static const struct rmi_transport_ops hid_rmi_ops = {
+	.write_block	= rmi_hid_write_block,
+	.read_block	= rmi_hid_read_block,
+	.reset		= rmi_hid_reset,
+};
+
 static int rmi_probe(struct hid_device *hdev, const struct hid_device_id *id)
 {
 	struct rmi_data *data = NULL;
@@ -1358,6 +617,14 @@ static int rmi_probe(struct hid_device *hdev, const struct hid_device_id *id)
 
 	mutex_init(&data->page_mutex);
 
+	if (data->device_flags & RMI_DEVICE_HAS_PHYS_BUTTONS)
+		rmi_hid_pdata.f30_data->disable = true;
+
+	data->xport.dev = hdev->dev.parent;
+	data->xport.pdata = rmi_hid_pdata;
+	data->xport.proto_name = "hid";
+	data->xport.ops = &hid_rmi_ops;
+
 start:
 	ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT);
 	if (ret) {
@@ -1365,17 +632,6 @@ start:
 		return ret;
 	}
 
-	if ((data->device_flags & RMI_DEVICE) &&
-	    !test_bit(RMI_STARTED, &data->flags))
-		/*
-		 * The device maybe in the bootloader if rmi_input_configured
-		 * failed to find F11 in the PDT. Print an error, but don't
-		 * return an error from rmi_probe so that hidraw will be
-		 * accessible from userspace. That way a userspace tool
-		 * can be used to reload working firmware on the touchpad.
-		 */
-		hid_err(hdev, "Device failed to be properly configured\n");
-
 	return 0;
 }
 
@@ -1384,6 +640,7 @@ static void rmi_remove(struct hid_device *hdev)
 	struct rmi_data *hdata = hid_get_drvdata(hdev);
 
 	clear_bit(RMI_STARTED, &hdata->flags);
+	rmi_unregister_transport_device(&hdata->xport);
 
 	hid_hw_stop(hdev);
 }
@@ -1408,7 +665,7 @@ static struct hid_driver rmi_driver = {
 #ifdef CONFIG_PM
 	.suspend		= rmi_suspend,
 	.resume			= rmi_post_resume,
-	.reset_resume		= rmi_post_reset,
+	.reset_resume		= rmi_post_resume,
 #endif
 };
 
-- 
2.5.0

^ permalink raw reply related	[flat|nested] 2+ messages in thread