[PATCH V2 RESEND 0/4] regulator: Add support for configuration of active-discharge

[PATCH V2 RESEND 0/4] regulator: Add support for configuration of active-discharge

[Laxman Dewangan]

This series add the common regulator DT property  for configuration
of active discharge and implementing this in regulator core.
Also implementing the regulator ops for MAX77620 to configure
active discharge.

This is based on discussion on patch and comment from Mark Brown:
[PATCH V6 7/8] DT: regulator: add DT binding doc for regulator of PMIC max77620/max20024

> +- maxim,disable-active-discharge:    boolean, Disable active discharge.

That's something I've seen other regulators do, can we make it a standard property with an op?

---
Changes from V1: 
 Make the interface like 0 (non-init member) will be treated as default,
 1 for disable and 2 for enable. Created enum for active discharge
 default/enable/disable

Resending as earlier sequence was messed up.


Laxman Dewangan (4):
  regulator: DT: Add DT property for active-discharge configuration
  regulator: core: Add support for active-discharge configuration
  regulator: helper: Add helper to configure active-discharge using
    regmap
  regulator: max77620: Add support to configure active-discharge

 .../devicetree/bindings/regulator/regulator.txt    |  5 +++++
 drivers/regulator/core.c                           | 10 ++++++++++
 drivers/regulator/helpers.c                        | 23 ++++++++++++++++++++++
 drivers/regulator/max77620-regulator.c             |  9 +++++++++
 drivers/regulator/of_regulator.c                   |  5 +++++
 include/linux/regulator/driver.h                   | 17 ++++++++++++++++
 include/linux/regulator/machine.h                  |  4 ++++
 7 files changed, 73 insertions(+)

-- 
2.1.4

[PATCH V2 RESEND 0/4] regulator: Add support for configuration of active-discharge

[Laxman Dewangan]

This series add the common regulator DT property  for configuration
of active discharge and implementing this in regulator core.
Also implementing the regulator ops for MAX77620 to configure
active discharge.

This is based on discussion on patch and comment from Mark Brown:
[PATCH V6 7/8] DT: regulator: add DT binding doc for regulator of PMIC max77620/max20024

> +- maxim,disable-active-discharge:    boolean, Disable active discharge.

That's something I've seen other regulators do, can we make it a standard property with an op?

---
Changes from V1: 
 Make the interface like 0 (non-init member) will be treated as default,
 1 for disable and 2 for enable. Created enum for active discharge
 default/enable/disable

Resending as earlier sequence was messed up.


Laxman Dewangan (4):
  regulator: DT: Add DT property for active-discharge configuration
  regulator: core: Add support for active-discharge configuration
  regulator: helper: Add helper to configure active-discharge using
    regmap
  regulator: max77620: Add support to configure active-discharge

 .../devicetree/bindings/regulator/regulator.txt    |  5 +++++
 drivers/regulator/core.c                           | 10 ++++++++++
 drivers/regulator/helpers.c                        | 23 ++++++++++++++++++++++
 drivers/regulator/max77620-regulator.c             |  9 +++++++++
 drivers/regulator/of_regulator.c                   |  5 +++++
 include/linux/regulator/driver.h                   | 17 ++++++++++++++++
 include/linux/regulator/machine.h                  |  4 ++++
 7 files changed, 73 insertions(+)

-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH V2 RESEND 1/4] regulator: DT: Add DT property for active-discharge configuration

[Laxman Dewangan]

Add common DT property for regulator node to support of
active discharge enable/disable configuration of regulator.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
 None

 Documentation/devicetree/bindings/regulator/regulator.txt | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index 1d112fc..ecfc593 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -44,6 +44,11 @@ Optional properties:
   any consumer request.
 - regulator-pull-down: Enable pull down resistor when the regulator is disabled.
 - regulator-over-current-protection: Enable over current protection.
+- regulator-active-discharge: tristate, enable/disable active discharge of
+  regulators. The values are:
+	0: Disable active discharge.
+	1: Enable active discharge.
+	Absence of this property will leave configuration to default.
 
 Deprecated properties:
 - regulator-compatible: If a regulator chip contains multiple
-- 
2.1.4

[PATCH V2 RESEND 1/4] regulator: DT: Add DT property for active-discharge configuration

[Laxman Dewangan]

Add common DT property for regulator node to support of
active discharge enable/disable configuration of regulator.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
 None

 Documentation/devicetree/bindings/regulator/regulator.txt | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index 1d112fc..ecfc593 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -44,6 +44,11 @@ Optional properties:
   any consumer request.
 - regulator-pull-down: Enable pull down resistor when the regulator is disabled.
 - regulator-over-current-protection: Enable over current protection.
+- regulator-active-discharge: tristate, enable/disable active discharge of
+  regulators. The values are:
+	0: Disable active discharge.
+	1: Enable active discharge.
+	Absence of this property will leave configuration to default.
 
 Deprecated properties:
 - regulator-compatible: If a regulator chip contains multiple
-- 
2.1.4

[PATCH V2 RESEND 2/4] regulator: core: Add support for active-discharge configuration

[Laxman Dewangan]

Add support to enable/disable active discharge of regulator via
machine constraints. This configuration is done when setting
machine constraint during regulator register and if regulator
driver implemented the callback ops.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
 Make the interface like 0 (non-init member) will be treated as default,
 1 for disable and 2 for enable. Created enum for active discharge
 default/enable/disable


 drivers/regulator/core.c          | 11 +++++++++++
 drivers/regulator/of_regulator.c  |  6 ++++++
 include/linux/regulator/driver.h  |  3 +++
 include/linux/regulator/machine.h | 12 ++++++++++++
 4 files changed, 32 insertions(+)

diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index 055f8c1..095de51 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -1139,6 +1139,17 @@ static int set_machine_constraints(struct regulator_dev *rdev,
 		}
 	}
 
+	if (rdev->constraints->active_discharge && ops->set_active_discharge) {
+		bool ad_state = (rdev->constraints->active_discharge ==
+			      REGULATOR_ACTIVE_DISCHARGE_ENABLE) ? true : false;
+
+		ret = ops->set_active_discharge(rdev, ad_state);
+		if (ret < 0) {
+			rdev_err(rdev, "failed to set active discharge\n");
+			return ret;
+		}
+	}
+
 	print_constraints(rdev);
 	return 0;
 }
diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c
index 499e437..fe2e3344 100644
--- a/drivers/regulator/of_regulator.c
+++ b/drivers/regulator/of_regulator.c
@@ -93,6 +93,12 @@ static void of_get_regulation_constraints(struct device_node *np,
 
 	constraints->soft_start = of_property_read_bool(np,
 					"regulator-soft-start");
+	ret = of_property_read_u32(np, "regulator-active-discharge", &pval);
+	if (!ret) {
+		constraints->active_discharge =
+				(pval) ? REGULATOR_ACTIVE_DISCHARGE_ENABLE :
+					REGULATOR_ACTIVE_DISCHARGE_DISABLE;
+	}
 
 	if (!of_property_read_u32(np, "regulator-initial-mode", &pval)) {
 		if (desc && desc->of_map_mode) {
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index 16ac9e1..59dbaf7 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -93,6 +93,8 @@ struct regulator_linear_range {
  * @get_current_limit: Get the configured limit for a current-limited regulator.
  * @set_input_current_limit: Configure an input limit.
  *
+ * @set_active_discharge: Set active discharge enable/disable of regulators.
+ *
  * @set_mode: Set the configured operating mode for the regulator.
  * @get_mode: Get the configured operating mode for the regulator.
  * @get_status: Return actual (not as-configured) status of regulator, as a
@@ -149,6 +151,7 @@ struct regulator_ops {
 
 	int (*set_input_current_limit) (struct regulator_dev *, int lim_uA);
 	int (*set_over_current_protection) (struct regulator_dev *);
+	int (*set_active_discharge) (struct regulator_dev *, bool enable);
 
 	/* enable/disable regulator */
 	int (*enable) (struct regulator_dev *);
diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h
index a1067d0..5d627c8 100644
--- a/include/linux/regulator/machine.h
+++ b/include/linux/regulator/machine.h
@@ -42,6 +42,13 @@ struct regulator;
 #define REGULATOR_CHANGE_DRMS		0x10
 #define REGULATOR_CHANGE_BYPASS		0x20
 
+/* Regulator active discharge flags */
+enum regulator_active_discharge {
+	REGULATOR_ACTIVE_DISCHARGE_DEFAULT,
+	REGULATOR_ACTIVE_DISCHARGE_DISABLE,
+	REGULATOR_ACTIVE_DISCHARGE_ENABLE,
+};
+
 /**
  * struct regulator_state - regulator state during low power system states
  *
@@ -100,6 +107,9 @@ struct regulator_state {
  * @initial_state: Suspend state to set by default.
  * @initial_mode: Mode to set at startup.
  * @ramp_delay: Time to settle down after voltage change (unit: uV/us)
+ * @active_discharge: Enable/disable active discharge. The enum
+ *		      regulator_active_discharge values are used for
+ *		      initialisation.
  * @enable_time: Turn-on time of the rails (unit: microseconds)
  */
 struct regulation_constraints {
@@ -140,6 +150,8 @@ struct regulation_constraints {
 	unsigned int ramp_delay;
 	unsigned int enable_time;
 
+	unsigned int active_discharge;
+
 	/* constraint flags */
 	unsigned always_on:1;	/* regulator never off when system is on */
 	unsigned boot_on:1;	/* bootloader/firmware enabled regulator */
-- 
2.1.4

[PATCH V2 RESEND 2/4] regulator: core: Add support for active-discharge configuration

[Laxman Dewangan]

Add support to enable/disable active discharge of regulator via
machine constraints. This configuration is done when setting
machine constraint during regulator register and if regulator
driver implemented the callback ops.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
 Make the interface like 0 (non-init member) will be treated as default,
 1 for disable and 2 for enable. Created enum for active discharge
 default/enable/disable


 drivers/regulator/core.c          | 11 +++++++++++
 drivers/regulator/of_regulator.c  |  6 ++++++
 include/linux/regulator/driver.h  |  3 +++
 include/linux/regulator/machine.h | 12 ++++++++++++
 4 files changed, 32 insertions(+)

diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index 055f8c1..095de51 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -1139,6 +1139,17 @@ static int set_machine_constraints(struct regulator_dev *rdev,
 		}
 	}
 
+	if (rdev->constraints->active_discharge && ops->set_active_discharge) {
+		bool ad_state = (rdev->constraints->active_discharge ==
+			      REGULATOR_ACTIVE_DISCHARGE_ENABLE) ? true : false;
+
+		ret = ops->set_active_discharge(rdev, ad_state);
+		if (ret < 0) {
+			rdev_err(rdev, "failed to set active discharge\n");
+			return ret;
+		}
+	}
+
 	print_constraints(rdev);
 	return 0;
 }
diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c
index 499e437..fe2e3344 100644
--- a/drivers/regulator/of_regulator.c
+++ b/drivers/regulator/of_regulator.c
@@ -93,6 +93,12 @@ static void of_get_regulation_constraints(struct device_node *np,
 
 	constraints->soft_start = of_property_read_bool(np,
 					"regulator-soft-start");
+	ret = of_property_read_u32(np, "regulator-active-discharge", &pval);
+	if (!ret) {
+		constraints->active_discharge =
+				(pval) ? REGULATOR_ACTIVE_DISCHARGE_ENABLE :
+					REGULATOR_ACTIVE_DISCHARGE_DISABLE;
+	}
 
 	if (!of_property_read_u32(np, "regulator-initial-mode", &pval)) {
 		if (desc && desc->of_map_mode) {
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index 16ac9e1..59dbaf7 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -93,6 +93,8 @@ struct regulator_linear_range {
  * @get_current_limit: Get the configured limit for a current-limited regulator.
  * @set_input_current_limit: Configure an input limit.
  *
+ * @set_active_discharge: Set active discharge enable/disable of regulators.
+ *
  * @set_mode: Set the configured operating mode for the regulator.
  * @get_mode: Get the configured operating mode for the regulator.
  * @get_status: Return actual (not as-configured) status of regulator, as a
@@ -149,6 +151,7 @@ struct regulator_ops {
 
 	int (*set_input_current_limit) (struct regulator_dev *, int lim_uA);
 	int (*set_over_current_protection) (struct regulator_dev *);
+	int (*set_active_discharge) (struct regulator_dev *, bool enable);
 
 	/* enable/disable regulator */
 	int (*enable) (struct regulator_dev *);
diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h
index a1067d0..5d627c8 100644
--- a/include/linux/regulator/machine.h
+++ b/include/linux/regulator/machine.h
@@ -42,6 +42,13 @@ struct regulator;
 #define REGULATOR_CHANGE_DRMS		0x10
 #define REGULATOR_CHANGE_BYPASS		0x20
 
+/* Regulator active discharge flags */
+enum regulator_active_discharge {
+	REGULATOR_ACTIVE_DISCHARGE_DEFAULT,
+	REGULATOR_ACTIVE_DISCHARGE_DISABLE,
+	REGULATOR_ACTIVE_DISCHARGE_ENABLE,
+};
+
 /**
  * struct regulator_state - regulator state during low power system states
  *
@@ -100,6 +107,9 @@ struct regulator_state {
  * @initial_state: Suspend state to set by default.
  * @initial_mode: Mode to set at startup.
  * @ramp_delay: Time to settle down after voltage change (unit: uV/us)
+ * @active_discharge: Enable/disable active discharge. The enum
+ *		      regulator_active_discharge values are used for
+ *		      initialisation.
  * @enable_time: Turn-on time of the rails (unit: microseconds)
  */
 struct regulation_constraints {
@@ -140,6 +150,8 @@ struct regulation_constraints {
 	unsigned int ramp_delay;
 	unsigned int enable_time;
 
+	unsigned int active_discharge;
+
 	/* constraint flags */
 	unsigned always_on:1;	/* regulator never off when system is on */
 	unsigned boot_on:1;	/* bootloader/firmware enabled regulator */
-- 
2.1.4

[PATCH V2 RESEND 3/4] regulator: helper: Add helper to configure active-discharge using regmap

[Laxman Dewangan]

Add helper function to set the state of active-discharge of
regulator using regmap. The HW regulator driver can directly
use this by providing the necessary information in the regulator
descriptor.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
 None

 drivers/regulator/helpers.c      | 23 +++++++++++++++++++++++
 include/linux/regulator/driver.h | 14 ++++++++++++++
 2 files changed, 37 insertions(+)

diff --git a/drivers/regulator/helpers.c b/drivers/regulator/helpers.c
index 3bbb326..b1e32e7 100644
--- a/drivers/regulator/helpers.c
+++ b/drivers/regulator/helpers.c
@@ -465,3 +465,26 @@ int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable)
 	return 0;
 }
 EXPORT_SYMBOL_GPL(regulator_get_bypass_regmap);
+
+/**
+ * regulator_set_active_discharge_regmap - Default set_active_discharge()
+ *					   using regmap
+ *
+ * @rdev: device to operate on.
+ * @enable: state to set, 0 to disable and 1 to enable.
+ */
+int regulator_set_active_discharge_regmap(struct regulator_dev *rdev,
+					  bool enable)
+{
+	unsigned int val;
+
+	if (enable)
+		val = rdev->desc->active_discharge_on;
+	else
+		val = rdev->desc->active_discharge_off;
+
+	return regmap_update_bits(rdev->regmap,
+				  rdev->desc->active_discharge_reg,
+				  rdev->desc->active_discharge_mask, val);
+}
+EXPORT_SYMBOL_GPL(regulator_set_active_discharge_regmap);
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index 59dbaf7..cd271e8 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -269,6 +269,14 @@ enum regulator_type {
  * @bypass_mask: Mask for control when using regmap set_bypass
  * @bypass_val_on: Enabling value for control when using regmap set_bypass
  * @bypass_val_off: Disabling value for control when using regmap set_bypass
+ * @active_discharge_off: Enabling value for control when using regmap
+ *			  set_active_discharge
+ * @active_discharge_on: Disabling value for control when using regmap
+ *			 set_active_discharge
+ * @active_discharge_mask: Mask for control when using regmap
+ *			   set_active_discharge
+ * @active_discharge_reg: Register for control when using regmap
+ *			  set_active_discharge
  *
  * @enable_time: Time taken for initial enable of regulator (in uS).
  * @off_on_delay: guard time (in uS), before re-enabling a regulator
@@ -318,6 +326,10 @@ struct regulator_desc {
 	unsigned int bypass_mask;
 	unsigned int bypass_val_on;
 	unsigned int bypass_val_off;
+	unsigned int active_discharge_on;
+	unsigned int active_discharge_off;
+	unsigned int active_discharge_mask;
+	unsigned int active_discharge_reg;
 
 	unsigned int enable_time;
 
@@ -450,6 +462,8 @@ int regulator_set_voltage_time_sel(struct regulator_dev *rdev,
 int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable);
 int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable);
 
+int regulator_set_active_discharge_regmap(struct regulator_dev *rdev,
+					  bool enable);
 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data);
 
 #endif
-- 
2.1.4

[PATCH V2 RESEND 3/4] regulator: helper: Add helper to configure active-discharge using regmap

[Laxman Dewangan]

Add helper function to set the state of active-discharge of
regulator using regmap. The HW regulator driver can directly
use this by providing the necessary information in the regulator
descriptor.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
 None

 drivers/regulator/helpers.c      | 23 +++++++++++++++++++++++
 include/linux/regulator/driver.h | 14 ++++++++++++++
 2 files changed, 37 insertions(+)

diff --git a/drivers/regulator/helpers.c b/drivers/regulator/helpers.c
index 3bbb326..b1e32e7 100644
--- a/drivers/regulator/helpers.c
+++ b/drivers/regulator/helpers.c
@@ -465,3 +465,26 @@ int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable)
 	return 0;
 }
 EXPORT_SYMBOL_GPL(regulator_get_bypass_regmap);
+
+/**
+ * regulator_set_active_discharge_regmap - Default set_active_discharge()
+ *					   using regmap
+ *
+ * @rdev: device to operate on.
+ * @enable: state to set, 0 to disable and 1 to enable.
+ */
+int regulator_set_active_discharge_regmap(struct regulator_dev *rdev,
+					  bool enable)
+{
+	unsigned int val;
+
+	if (enable)
+		val = rdev->desc->active_discharge_on;
+	else
+		val = rdev->desc->active_discharge_off;
+
+	return regmap_update_bits(rdev->regmap,
+				  rdev->desc->active_discharge_reg,
+				  rdev->desc->active_discharge_mask, val);
+}
+EXPORT_SYMBOL_GPL(regulator_set_active_discharge_regmap);
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index 59dbaf7..cd271e8 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -269,6 +269,14 @@ enum regulator_type {
  * @bypass_mask: Mask for control when using regmap set_bypass
  * @bypass_val_on: Enabling value for control when using regmap set_bypass
  * @bypass_val_off: Disabling value for control when using regmap set_bypass
+ * @active_discharge_off: Enabling value for control when using regmap
+ *			  set_active_discharge
+ * @active_discharge_on: Disabling value for control when using regmap
+ *			 set_active_discharge
+ * @active_discharge_mask: Mask for control when using regmap
+ *			   set_active_discharge
+ * @active_discharge_reg: Register for control when using regmap
+ *			  set_active_discharge
  *
  * @enable_time: Time taken for initial enable of regulator (in uS).
  * @off_on_delay: guard time (in uS), before re-enabling a regulator
@@ -318,6 +326,10 @@ struct regulator_desc {
 	unsigned int bypass_mask;
 	unsigned int bypass_val_on;
 	unsigned int bypass_val_off;
+	unsigned int active_discharge_on;
+	unsigned int active_discharge_off;
+	unsigned int active_discharge_mask;
+	unsigned int active_discharge_reg;
 
 	unsigned int enable_time;
 
@@ -450,6 +462,8 @@ int regulator_set_voltage_time_sel(struct regulator_dev *rdev,
 int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable);
 int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable);
 
+int regulator_set_active_discharge_regmap(struct regulator_dev *rdev,
+					  bool enable);
 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data);
 
 #endif
-- 
2.1.4

[PATCH V2 RESEND 4/4] regulator: max77620: Add support to configure active-discharge

[Laxman Dewangan]

Add regulator ops callback for configuration of active-discharge
and provide necessarily information via regulator descriptor.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
 None

 drivers/regulator/max77620-regulator.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/regulator/max77620-regulator.c b/drivers/regulator/max77620-regulator.c
index 259e7e1..73a3356 100644
--- a/drivers/regulator/max77620-regulator.c
+++ b/drivers/regulator/max77620-regulator.c
@@ -578,6 +578,7 @@ static struct regulator_ops max77620_regulator_ops = {
 	.get_mode = max77620_regulator_get_mode,
 	.set_ramp_delay = max77620_regulator_set_ramp_delay,
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
 };
 
 #define MAX77620_SD_CNF2_ROVS_EN_NONE	0
@@ -606,6 +607,10 @@ static struct regulator_ops max77620_regulator_ops = {
 			.enable_time = 500,				\
 			.vsel_mask = MAX77620_##_volt_mask##_VOLT_MASK,	\
 			.vsel_reg = MAX77620_REG_##_id,			\
+			.active_discharge_off = 0,			\
+			.active_discharge_on = MAX77620_SD_CFG1_ADE_ENABLE, \
+			.active_discharge_mask = MAX77620_SD_CFG1_ADE_MASK, \
+			.active_discharge_reg = MAX77620_REG_##_id##_CFG, \
 			.type = REGULATOR_VOLTAGE,			\
 		},							\
 	}
@@ -633,6 +638,10 @@ static struct regulator_ops max77620_regulator_ops = {
 			.enable_time = 500,				\
 			.vsel_mask = MAX77620_LDO_VOLT_MASK,		\
 			.vsel_reg = MAX77620_REG_##_id##_CFG,		\
+			.active_discharge_off = 0,			\
+			.active_discharge_on = MAX77620_LDO_CFG2_ADE_ENABLE, \
+			.active_discharge_mask = MAX77620_LDO_CFG2_ADE_MASK, \
+			.active_discharge_reg = MAX77620_REG_##_id##_CFG2, \
 			.type = REGULATOR_VOLTAGE,			\
 		},							\
 	}
-- 
2.1.4

[PATCH V2 RESEND 4/4] regulator: max77620: Add support to configure active-discharge

[Laxman Dewangan]

Add regulator ops callback for configuration of active-discharge
and provide necessarily information via regulator descriptor.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
---
Changes from V1:
 None

 drivers/regulator/max77620-regulator.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/regulator/max77620-regulator.c b/drivers/regulator/max77620-regulator.c
index 259e7e1..73a3356 100644
--- a/drivers/regulator/max77620-regulator.c
+++ b/drivers/regulator/max77620-regulator.c
@@ -578,6 +578,7 @@ static struct regulator_ops max77620_regulator_ops = {
 	.get_mode = max77620_regulator_get_mode,
 	.set_ramp_delay = max77620_regulator_set_ramp_delay,
 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
 };
 
 #define MAX77620_SD_CNF2_ROVS_EN_NONE	0
@@ -606,6 +607,10 @@ static struct regulator_ops max77620_regulator_ops = {
 			.enable_time = 500,				\
 			.vsel_mask = MAX77620_##_volt_mask##_VOLT_MASK,	\
 			.vsel_reg = MAX77620_REG_##_id,			\
+			.active_discharge_off = 0,			\
+			.active_discharge_on = MAX77620_SD_CFG1_ADE_ENABLE, \
+			.active_discharge_mask = MAX77620_SD_CFG1_ADE_MASK, \
+			.active_discharge_reg = MAX77620_REG_##_id##_CFG, \
 			.type = REGULATOR_VOLTAGE,			\
 		},							\
 	}
@@ -633,6 +638,10 @@ static struct regulator_ops max77620_regulator_ops = {
 			.enable_time = 500,				\
 			.vsel_mask = MAX77620_LDO_VOLT_MASK,		\
 			.vsel_reg = MAX77620_REG_##_id##_CFG,		\
+			.active_discharge_off = 0,			\
+			.active_discharge_on = MAX77620_LDO_CFG2_ADE_ENABLE, \
+			.active_discharge_mask = MAX77620_LDO_CFG2_ADE_MASK, \
+			.active_discharge_reg = MAX77620_REG_##_id##_CFG2, \
 			.type = REGULATOR_VOLTAGE,			\
 		},							\
 	}
-- 
2.1.4

Re: [PATCH V2 RESEND 1/4] regulator: DT: Add DT property for active-discharge configuration

[Rob Herring]

On Wed, Mar 02, 2016 at 04:24:45PM +0530, Laxman Dewangan wrote:
> Add common DT property for regulator node to support of
> active discharge enable/disable configuration of regulator.
> 
> Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
> ---
> Changes from V1:
>  None
> 
>  Documentation/devicetree/bindings/regulator/regulator.txt | 5 +++++
>  1 file changed, 5 insertions(+)

Looks okay to me, but for a common property I don't understand what 
active discharge means (or why you would want to use it).

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH V2 RESEND 1/4] regulator: DT: Add DT property for active-discharge configuration

[Rob Herring]

On Wed, Mar 02, 2016 at 04:24:45PM +0530, Laxman Dewangan wrote:
> Add common DT property for regulator node to support of
> active discharge enable/disable configuration of regulator.
> 
> Signed-off-by: Laxman Dewangan <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
> ---
> Changes from V1:
>  None
> 
>  Documentation/devicetree/bindings/regulator/regulator.txt | 5 +++++
>  1 file changed, 5 insertions(+)

Looks okay to me, but for a common property I don't understand what 
active discharge means (or why you would want to use it).

Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html