* [PATCH] ARM: dts: sun8i: Add dts for Orange Pi 2 SBC
@ 2016-03-23 10:17 ` Hans de Goede
0 siblings, 0 replies; 8+ messages in thread
From: Hans de Goede @ 2016-03-23 10:17 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Hans de Goede
The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.
Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 186 ++++++++++++++++++++++++++++++
2 files changed, 187 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 31d50a4..282d8e4 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -699,6 +699,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-sinlinx-sina33.dtb \
sun8i-a83t-allwinner-h8homlet-v2.dtb \
sun8i-a83t-cubietruck-plus.dtb \
+ sun8i-h3-orangepi-2.dtb \
sun8i-h3-orangepi-pc.dtb \
sun8i-h3-orangepi-plus.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
new file mode 100644
index 0000000..f93f5d1
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
@@ -0,0 +1,186 @@
+/*
+ * Copyright (C) 2016 Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi 2";
+ compatible = "xunlong,orangepi-2", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_opc>;
+
+ sw2 {
+ label = "sw2";
+ linux,code = <BTN_1>;
+ gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
+ };
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_pwrseq_pin_orangepi>;
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&pio {
+ leds_opc: led_pins@0 {
+ allwinner,pins = "PA15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_pio {
+ leds_r_opc: led_pins@0 {
+ allwinner,pins = "PL10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ sw_r_opc: key_pins@0 {
+ allwinner,pins = "PL3", "PL4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin@0 {
+ allwinner,pins = "PL7";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb1_vbus_pin_a {
+ allwinner,pins = "PG13";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--
2.7.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH] ARM: dts: sun8i: Add dts for Orange Pi 2 SBC
@ 2016-03-23 10:17 ` Hans de Goede
0 siblings, 0 replies; 8+ messages in thread
From: Hans de Goede @ 2016-03-23 10:17 UTC (permalink / raw)
To: linux-arm-kernel
The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 186 ++++++++++++++++++++++++++++++
2 files changed, 187 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 31d50a4..282d8e4 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -699,6 +699,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-sinlinx-sina33.dtb \
sun8i-a83t-allwinner-h8homlet-v2.dtb \
sun8i-a83t-cubietruck-plus.dtb \
+ sun8i-h3-orangepi-2.dtb \
sun8i-h3-orangepi-pc.dtb \
sun8i-h3-orangepi-plus.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
new file mode 100644
index 0000000..f93f5d1
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
@@ -0,0 +1,186 @@
+/*
+ * Copyright (C) 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi 2";
+ compatible = "xunlong,orangepi-2", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_opc>;
+
+ sw2 {
+ label = "sw2";
+ linux,code = <BTN_1>;
+ gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
+ };
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_pwrseq_pin_orangepi>;
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&pio {
+ leds_opc: led_pins at 0 {
+ allwinner,pins = "PA15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_pio {
+ leds_r_opc: led_pins at 0 {
+ allwinner,pins = "PL10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ sw_r_opc: key_pins at 0 {
+ allwinner,pins = "PL3", "PL4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin at 0 {
+ allwinner,pins = "PL7";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_usb1_vbus {
+ gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usb1_vbus_pin_a {
+ allwinner,pins = "PG13";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--
2.7.3
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH] ARM: dts: sun8i: Add dts for Orange Pi 2 SBC
2016-03-23 10:17 ` Hans de Goede
@ 2016-03-24 7:54 ` Maxime Ripard
-1 siblings, 0 replies; 8+ messages in thread
From: Maxime Ripard @ 2016-03-24 7:54 UTC (permalink / raw)
To: Hans de Goede
Cc: Chen-Yu Tsai, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree, linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
[-- Attachment #1: Type: text/plain, Size: 669 bytes --]
On Wed, Mar 23, 2016 at 11:17:05AM +0100, Hans de Goede wrote:
> The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
> 4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
> SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
> a TRRS headphone jack for stereo out and composite out, a microphone,
> an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
> and a 40-pin GPIO header.
>
> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH] ARM: dts: sun8i: Add dts for Orange Pi 2 SBC
@ 2016-03-24 7:54 ` Maxime Ripard
0 siblings, 0 replies; 8+ messages in thread
From: Maxime Ripard @ 2016-03-24 7:54 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Mar 23, 2016 at 11:17:05AM +0100, Hans de Goede wrote:
> The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
> 4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
> SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
> a TRRS headphone jack for stereo out and composite out, a microphone,
> an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
> and a 40-pin GPIO header.
>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160324/e9241c59/attachment.sig>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH] ARM: dts: sun8i: Add dts for Orange Pi 2 SBC
2016-03-23 10:17 ` Hans de Goede
@ 2016-03-25 11:53 ` Jean-Francois Moine
-1 siblings, 0 replies; 8+ messages in thread
From: Jean-Francois Moine @ 2016-03-25 11:53 UTC (permalink / raw)
To: Hans de Goede
Cc: Maxime Ripard, Chen-Yu Tsai, devicetree,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Wed, 23 Mar 2016 11:17:05 +0100
Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> wrote:
> The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
> 4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
> SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
> a TRRS headphone jack for stereo out and composite out, a microphone,
> an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
> and a 40-pin GPIO header.
>
> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 186 ++++++++++++++++++++++++++++++
> 2 files changed, 187 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
[snip]
> diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
> new file mode 100644
> index 0000000..f93f5d1
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
[snip]
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> + cd-inverted;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins_a>;
> + vmmc-supply = <®_vcc3v3>;
While still 3.3V, the power of the mmc1 if supplied by an other
regulator.
> + mmc-pwrseq = <&wifi_pwrseq>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +};
[snip]
--
Ken ar c'hentañ | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH] ARM: dts: sun8i: Add dts for Orange Pi 2 SBC
@ 2016-03-25 11:53 ` Jean-Francois Moine
0 siblings, 0 replies; 8+ messages in thread
From: Jean-Francois Moine @ 2016-03-25 11:53 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, 23 Mar 2016 11:17:05 +0100
Hans de Goede <hdegoede@redhat.com> wrote:
> The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
> 4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
> SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
> a TRRS headphone jack for stereo out and composite out, a microphone,
> an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
> and a 40-pin GPIO header.
>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 186 ++++++++++++++++++++++++++++++
> 2 files changed, 187 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
[snip]
> diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
> new file mode 100644
> index 0000000..f93f5d1
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
[snip]
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> + cd-inverted;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins_a>;
> + vmmc-supply = <®_vcc3v3>;
While still 3.3V, the power of the mmc1 if supplied by an other
regulator.
> + mmc-pwrseq = <&wifi_pwrseq>;
> + bus-width = <4>;
> + non-removable;
> + status = "okay";
> +};
[snip]
--
Ken ar c'henta? | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Re: [PATCH] ARM: dts: sun8i: Add dts for Orange Pi 2 SBC
2016-03-25 11:53 ` Jean-Francois Moine
@ 2016-03-28 12:36 ` Hans de Goede
-1 siblings, 0 replies; 8+ messages in thread
From: Hans de Goede @ 2016-03-28 12:36 UTC (permalink / raw)
To: Jean-Francois Moine
Cc: Maxime Ripard, Chen-Yu Tsai, devicetree,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi,
On 25-03-16 12:53, Jean-Francois Moine wrote:
> On Wed, 23 Mar 2016 11:17:05 +0100
> Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> wrote:
>
>> The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
>> 4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
>> SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
>> a TRRS headphone jack for stereo out and composite out, a microphone,
>> an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
>> and a 40-pin GPIO header.
>>
>> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
>> ---
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 186 ++++++++++++++++++++++++++++++
>> 2 files changed, 187 insertions(+)
>> create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
> [snip]
>> diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
>> new file mode 100644
>> index 0000000..f93f5d1
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
> [snip]
>> +&mmc0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
>> + vmmc-supply = <®_vcc3v3>;
>> + bus-width = <4>;
>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
>> + cd-inverted;
>> + status = "okay";
>> +};
>> +
>> +&mmc1 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc1_pins_a>;
>> + vmmc-supply = <®_vcc3v3>;
>
> While still 3.3V, the power of the mmc1 if supplied by an other
> regulator.
I do not have schematics for the OPi 2, on the OPi plus schematic the
2 share a regulator. But even if it is another fixed 3.3V regulator,
there is little use in modelling it as a separate regulator when we
cannot control it.
Regards,
Hans
^ permalink raw reply [flat|nested] 8+ messages in thread
* [linux-sunxi] Re: [PATCH] ARM: dts: sun8i: Add dts for Orange Pi 2 SBC
@ 2016-03-28 12:36 ` Hans de Goede
0 siblings, 0 replies; 8+ messages in thread
From: Hans de Goede @ 2016-03-28 12:36 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On 25-03-16 12:53, Jean-Francois Moine wrote:
> On Wed, 23 Mar 2016 11:17:05 +0100
> Hans de Goede <hdegoede@redhat.com> wrote:
>
>> The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
>> 4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
>> SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
>> a TRRS headphone jack for stereo out and composite out, a microphone,
>> an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
>> and a 40-pin GPIO header.
>>
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>> ---
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/sun8i-h3-orangepi-2.dts | 186 ++++++++++++++++++++++++++++++
>> 2 files changed, 187 insertions(+)
>> create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
> [snip]
>> diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
>> new file mode 100644
>> index 0000000..f93f5d1
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
> [snip]
>> +&mmc0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
>> + vmmc-supply = <®_vcc3v3>;
>> + bus-width = <4>;
>> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
>> + cd-inverted;
>> + status = "okay";
>> +};
>> +
>> +&mmc1 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc1_pins_a>;
>> + vmmc-supply = <®_vcc3v3>;
>
> While still 3.3V, the power of the mmc1 if supplied by an other
> regulator.
I do not have schematics for the OPi 2, on the OPi plus schematic the
2 share a regulator. But even if it is another fixed 3.3V regulator,
there is little use in modelling it as a separate regulator when we
cannot control it.
Regards,
Hans
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2016-03-28 12:36 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-03-23 10:17 [PATCH] ARM: dts: sun8i: Add dts for Orange Pi 2 SBC Hans de Goede
2016-03-23 10:17 ` Hans de Goede
[not found] ` <1458728225-6922-1-git-send-email-hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
2016-03-24 7:54 ` Maxime Ripard
2016-03-24 7:54 ` Maxime Ripard
2016-03-25 11:53 ` Jean-Francois Moine
2016-03-25 11:53 ` Jean-Francois Moine
[not found] ` <20160325125342.2b4b6c9ec2e4922b51687ad3-GANU6spQydw@public.gmane.org>
2016-03-28 12:36 ` Hans de Goede
2016-03-28 12:36 ` [linux-sunxi] " Hans de Goede
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.