* [PATCH v6 00/12] ARM/arm64: dts: rcar: Add SYSC PM domains
@ 2016-04-22 9:07 ` Geert Uytterhoeven
0 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-pm-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, Geert Uytterhoeven
Hi Simon, Magnus,
This patch series adds the R-Car System Controller to the DTS files for
the various Renesas R-Car SoCs, and hooks up devices to their respective
PM domains.
This (more specifically patch 1) is a dependency for the enablement of the
Display Unit on R-Car H3, as on this SoC the DU needs to use the VSPs, and the
VSPs are located in a PM Domain.
This series contains 2 parts, for both arm64 and arm32:
1. Patches 1 (arm64) and 3-7 (arm32) add device node for the System
Controllers, and hook up CPU cores and L2 caches/SCUs to their
respective PM Domains,
2. Patches 2 (arm64) and 8-12 (arm32) hook up devices to the SYSC
"always-on" PM Domain, for a more consistent device-power-area
description in DT.
Changes compared to v5:
- Add Acked-by,
- Rebased R-Car Gen2 patches because of dropping of references to the
second DMA controllers,
- Updated for addition of sdhi[0-2] device nodes on r8a7793,
- Reordered arm64 patches first, as these have a higher priority.
Changes compared to v4:
- Add Acked-by,
- Remove "power-domains" property again from the sysc nodes, as the
System Controller theirselves are not part of the Clock Domains.
Changes compared to v3:
- Add power-domains properties to the sysc nodes, to refer to the
SoC's Clock Domains,
- Extract using the SYSC "always-on" PM Domain on R-Car H3 into its
own patch,
- Add patches to use the SYSC "always-on" PM Domain on R-Car H1 and
R-Car Gen2,
- Update for recently added can0, can1, pciec0, and pciec1 device
nodes on R-Car H3.
Changes compared to v2:
- Move power area hierarchy from DT to C (cfr. DT bindings for Renesas
CPG/MSSR), and switch to "#power-domain-cells = <1>",
- Drop fallback compatibility strings, as the bindings are
SoC-specific,
- Add an "always-on" power area on R-Car H3.
Changes compared to v1:
- Add R-Car H3 (r8a7795) support,
- Use "renesas,<type>-sysc" instead of "renesas,sysc-<type>",
- Add fallback compatibility strings for R-Car Gen2 and Gen3.
Dependencies:
- renesas-devel-20160422v2-v4.6-rc4.
Suggested patch application strategy:
- On branch arm64-dt-for-v4.7:
- Merge rcar-sysc-for-v4.7,
- Apply patches 1-2.
- On branch dt-for-v4.7:
- Merge rcar-sysc-for-v4.7,
- Apply patches 3-12.
Suggested arm-soc pull request strategy:
- Send pull-request for rcar-sysc-for-v4.7,
- Send pull-request for arm64-dt-for-v4.7,
- Send pull-request for dt-for-v4.7.
For your convenience, I've pushed this to the topic/rcar-sysc-pd-dt-v6
branch of
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git.
Integration with renesas-drivers-2016-04-12-v4.6-rc3 is available in the
topic/gen3-latest branch.
This has been tested on r8a7779/marzen, r8a7790/lager, r8a7791/koelsch,
r8a7794/alt, and r8a7795/salvator-x.
Thanks for applying!
Geert Uytterhoeven (12):
arm64: dts: r8a7795: Add SYSC PM Domains
arm64: dts: r8a7795: Use SYSC "always-on" PM Domain
ARM: dts: r8a7779: Add SYSC PM Domains
ARM: dts: r8a7790: Add SYSC PM Domains
ARM: dts: r8a7791: Add SYSC PM Domains
ARM: dts: r8a7793: Add SYSC PM Domains
ARM: dts: r8a7794: Add SYSC PM Domains
ARM: dts: r8a7779: Use SYSC "always-on" PM Domain
ARM: dts: r8a7790: Use SYSC "always-on" PM Domain
ARM: dts: r8a7791: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
arch/arm/boot/dts/r8a7779.dtsi | 54 ++++++-----
arch/arm/boot/dts/r8a7790.dtsi | 155 ++++++++++++++++--------------
arch/arm/boot/dts/r8a7791.dtsi | 156 ++++++++++++++++---------------
arch/arm/boot/dts/r8a7793.dtsi | 111 ++++++++++++----------
arch/arm/boot/dts/r8a7794.dtsi | 116 ++++++++++++-----------
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 123 +++++++++++++-----------
6 files changed, 392 insertions(+), 323 deletions(-)
--
1.9.1
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH v6 00/12] ARM/arm64: dts: rcar: Add SYSC PM domains
@ 2016-04-22 9:07 ` Geert Uytterhoeven
0 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Hi Simon, Magnus,
This patch series adds the R-Car System Controller to the DTS files for
the various Renesas R-Car SoCs, and hooks up devices to their respective
PM domains.
This (more specifically patch 1) is a dependency for the enablement of the
Display Unit on R-Car H3, as on this SoC the DU needs to use the VSPs, and the
VSPs are located in a PM Domain.
This series contains 2 parts, for both arm64 and arm32:
1. Patches 1 (arm64) and 3-7 (arm32) add device node for the System
Controllers, and hook up CPU cores and L2 caches/SCUs to their
respective PM Domains,
2. Patches 2 (arm64) and 8-12 (arm32) hook up devices to the SYSC
"always-on" PM Domain, for a more consistent device-power-area
description in DT.
Changes compared to v5:
- Add Acked-by,
- Rebased R-Car Gen2 patches because of dropping of references to the
second DMA controllers,
- Updated for addition of sdhi[0-2] device nodes on r8a7793,
- Reordered arm64 patches first, as these have a higher priority.
Changes compared to v4:
- Add Acked-by,
- Remove "power-domains" property again from the sysc nodes, as the
System Controller theirselves are not part of the Clock Domains.
Changes compared to v3:
- Add power-domains properties to the sysc nodes, to refer to the
SoC's Clock Domains,
- Extract using the SYSC "always-on" PM Domain on R-Car H3 into its
own patch,
- Add patches to use the SYSC "always-on" PM Domain on R-Car H1 and
R-Car Gen2,
- Update for recently added can0, can1, pciec0, and pciec1 device
nodes on R-Car H3.
Changes compared to v2:
- Move power area hierarchy from DT to C (cfr. DT bindings for Renesas
CPG/MSSR), and switch to "#power-domain-cells = <1>",
- Drop fallback compatibility strings, as the bindings are
SoC-specific,
- Add an "always-on" power area on R-Car H3.
Changes compared to v1:
- Add R-Car H3 (r8a7795) support,
- Use "renesas,<type>-sysc" instead of "renesas,sysc-<type>",
- Add fallback compatibility strings for R-Car Gen2 and Gen3.
Dependencies:
- renesas-devel-20160422v2-v4.6-rc4.
Suggested patch application strategy:
- On branch arm64-dt-for-v4.7:
- Merge rcar-sysc-for-v4.7,
- Apply patches 1-2.
- On branch dt-for-v4.7:
- Merge rcar-sysc-for-v4.7,
- Apply patches 3-12.
Suggested arm-soc pull request strategy:
- Send pull-request for rcar-sysc-for-v4.7,
- Send pull-request for arm64-dt-for-v4.7,
- Send pull-request for dt-for-v4.7.
For your convenience, I've pushed this to the topic/rcar-sysc-pd-dt-v6
branch of
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git.
Integration with renesas-drivers-2016-04-12-v4.6-rc3 is available in the
topic/gen3-latest branch.
This has been tested on r8a7779/marzen, r8a7790/lager, r8a7791/koelsch,
r8a7794/alt, and r8a7795/salvator-x.
Thanks for applying!
Geert Uytterhoeven (12):
arm64: dts: r8a7795: Add SYSC PM Domains
arm64: dts: r8a7795: Use SYSC "always-on" PM Domain
ARM: dts: r8a7779: Add SYSC PM Domains
ARM: dts: r8a7790: Add SYSC PM Domains
ARM: dts: r8a7791: Add SYSC PM Domains
ARM: dts: r8a7793: Add SYSC PM Domains
ARM: dts: r8a7794: Add SYSC PM Domains
ARM: dts: r8a7779: Use SYSC "always-on" PM Domain
ARM: dts: r8a7790: Use SYSC "always-on" PM Domain
ARM: dts: r8a7791: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
arch/arm/boot/dts/r8a7779.dtsi | 54 ++++++-----
arch/arm/boot/dts/r8a7790.dtsi | 155 ++++++++++++++++--------------
arch/arm/boot/dts/r8a7791.dtsi | 156 ++++++++++++++++---------------
arch/arm/boot/dts/r8a7793.dtsi | 111 ++++++++++++----------
arch/arm/boot/dts/r8a7794.dtsi | 116 ++++++++++++-----------
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 123 +++++++++++++-----------
6 files changed, 392 insertions(+), 323 deletions(-)
--
1.9.1
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH v6 01/12] arm64: dts: r8a7795: Add SYSC PM Domains
2016-04-22 9:07 ` Geert Uytterhoeven
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: devicetree, Geert Uytterhoeven, linux-pm, linux-renesas-soc,
Laurent Pinchart, linux-arm-kernel
Add a device node for the System Controller.
Hook up the Cortex-A57 CPU cores and the Cortex-A57 and Cortex A53 L2
caches/SCUs to their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
- Extract using "<&sysc R8A7795_PD_ALWAYS_ON>" for devices in the
always-on power area into a separate patch,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
- Use "<&sysc R8A7795_PD_ALWAYS_ON>" for devices in the always-on
power area,
- Drop fallback compatibility strings,
v2:
- New.
---
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index 11f9971a85433b7f..9c7424fc171fb876 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -10,6 +10,7 @@
#include <dt-bindings/clock/r8a7795-cpg-mssr.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a7795-sysc.h>
/ {
compatible = "renesas,r8a7795";
@@ -39,6 +40,7 @@
compatible = "arm,cortex-a57", "arm,armv8";
reg = <0x0>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU0>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -47,6 +49,7 @@
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x1>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU1>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -54,6 +57,7 @@
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x2>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU2>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -61,6 +65,7 @@
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x3>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU3>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -68,12 +73,14 @@
L2_CA57: cache-controller@0 {
compatible = "cache";
+ power-domains = <&sysc R8A7795_PD_CA57_SCU>;
cache-unified;
cache-level = <2>;
};
L2_CA53: cache-controller@1 {
compatible = "cache";
+ power-domains = <&sysc R8A7795_PD_CA53_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -305,6 +312,12 @@
#power-domain-cells = <0>;
};
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7795-sysc";
+ reg = <0 0xe6180000 0 0x0400>;
+ #power-domain-cells = <1>;
+ };
+
audma0: dma-controller@ec700000 {
compatible = "renesas,rcar-dmac";
reg = <0 0xec700000 0 0x10000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 01/12] arm64: dts: r8a7795: Add SYSC PM Domains
@ 2016-04-22 9:07 ` Geert Uytterhoeven
0 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Add a device node for the System Controller.
Hook up the Cortex-A57 CPU cores and the Cortex-A57 and Cortex A53 L2
caches/SCUs to their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
- Extract using "<&sysc R8A7795_PD_ALWAYS_ON>" for devices in the
always-on power area into a separate patch,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
- Use "<&sysc R8A7795_PD_ALWAYS_ON>" for devices in the always-on
power area,
- Drop fallback compatibility strings,
v2:
- New.
---
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index 11f9971a85433b7f..9c7424fc171fb876 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -10,6 +10,7 @@
#include <dt-bindings/clock/r8a7795-cpg-mssr.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a7795-sysc.h>
/ {
compatible = "renesas,r8a7795";
@@ -39,6 +40,7 @@
compatible = "arm,cortex-a57", "arm,armv8";
reg = <0x0>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU0>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -47,6 +49,7 @@
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x1>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU1>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -54,6 +57,7 @@
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x2>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU2>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -61,6 +65,7 @@
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x3>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU3>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -68,12 +73,14 @@
L2_CA57: cache-controller@0 {
compatible = "cache";
+ power-domains = <&sysc R8A7795_PD_CA57_SCU>;
cache-unified;
cache-level = <2>;
};
L2_CA53: cache-controller@1 {
compatible = "cache";
+ power-domains = <&sysc R8A7795_PD_CA53_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -305,6 +312,12 @@
#power-domain-cells = <0>;
};
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7795-sysc";
+ reg = <0 0xe6180000 0 0x0400>;
+ #power-domain-cells = <1>;
+ };
+
audma0: dma-controller@ec700000 {
compatible = "renesas,rcar-dmac";
reg = <0 0xec700000 0 0x10000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 01/12] arm64: dts: r8a7795: Add SYSC PM Domains
@ 2016-04-22 9:07 ` Geert Uytterhoeven
0 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: linux-arm-kernel
Add a device node for the System Controller.
Hook up the Cortex-A57 CPU cores and the Cortex-A57 and Cortex A53 L2
caches/SCUs to their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
- Extract using "<&sysc R8A7795_PD_ALWAYS_ON>" for devices in the
always-on power area into a separate patch,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
- Use "<&sysc R8A7795_PD_ALWAYS_ON>" for devices in the always-on
power area,
- Drop fallback compatibility strings,
v2:
- New.
---
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index 11f9971a85433b7f..9c7424fc171fb876 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -10,6 +10,7 @@
#include <dt-bindings/clock/r8a7795-cpg-mssr.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a7795-sysc.h>
/ {
compatible = "renesas,r8a7795";
@@ -39,6 +40,7 @@
compatible = "arm,cortex-a57", "arm,armv8";
reg = <0x0>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU0>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -47,6 +49,7 @@
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x1>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU1>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -54,6 +57,7 @@
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x2>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU2>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -61,6 +65,7 @@
compatible = "arm,cortex-a57","arm,armv8";
reg = <0x3>;
device_type = "cpu";
+ power-domains = <&sysc R8A7795_PD_CA57_CPU3>;
next-level-cache = <&L2_CA57>;
enable-method = "psci";
};
@@ -68,12 +73,14 @@
L2_CA57: cache-controller at 0 {
compatible = "cache";
+ power-domains = <&sysc R8A7795_PD_CA57_SCU>;
cache-unified;
cache-level = <2>;
};
L2_CA53: cache-controller at 1 {
compatible = "cache";
+ power-domains = <&sysc R8A7795_PD_CA53_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -305,6 +312,12 @@
#power-domain-cells = <0>;
};
+ sysc: system-controller at e6180000 {
+ compatible = "renesas,r8a7795-sysc";
+ reg = <0 0xe6180000 0 0x0400>;
+ #power-domain-cells = <1>;
+ };
+
audma0: dma-controller at ec700000 {
compatible = "renesas,rcar-dmac";
reg = <0 0xec700000 0 0x10000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 02/12] arm64: dts: r8a7795: Use SYSC "always-on" PM Domain
2016-04-22 9:07 ` Geert Uytterhoeven
(?)
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Hook up all devices that are part of the CPG/MSSR Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- No changes,
v5:
- Add Acked-by,
v4:
- New, extracted from "[PATCH v3] arm64: dts: r8a7795: Add SYSC PM
Domains",
- Use "<&sysc R8A7795_PD_ALWAYS_ON>" for recently added can0, can1,
pciec0, and pciec1 device nodes,
---
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 110 +++++++++++++++----------------
1 file changed, 55 insertions(+), 55 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index 9c7424fc171fb876..1e0f43e72bf0eb80 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -178,7 +178,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 912>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
};
gpio1: gpio@e6051000 {
@@ -192,7 +192,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 911>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
};
gpio2: gpio@e6052000 {
@@ -206,7 +206,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 910>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
};
gpio3: gpio@e6053000 {
@@ -220,7 +220,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 909>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
};
gpio4: gpio@e6054000 {
@@ -234,7 +234,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 908>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
};
gpio5: gpio@e6055000 {
@@ -248,7 +248,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 907>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
};
gpio6: gpio@e6055400 {
@@ -262,7 +262,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 906>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
};
gpio7: gpio@e6055800 {
@@ -276,7 +276,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&cpg CPG_MOD 905>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
};
pmu_a57 {
@@ -345,7 +345,7 @@
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 502>;
clock-names = "fck";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <16>;
};
@@ -377,7 +377,7 @@
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 501>;
clock-names = "fck";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <16>;
};
@@ -399,7 +399,7 @@
GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 407>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
};
dmac0: dma-controller@e6700000 {
@@ -430,7 +430,7 @@
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 219>;
clock-names = "fck";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <16>;
};
@@ -463,7 +463,7 @@
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 218>;
clock-names = "fck";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <16>;
};
@@ -496,7 +496,7 @@
"ch12", "ch13", "ch14", "ch15";
clocks = <&cpg CPG_MOD 217>;
clock-names = "fck";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <16>;
};
@@ -538,7 +538,7 @@
"ch20", "ch21", "ch22", "ch23",
"ch24";
clocks = <&cpg CPG_MOD 812>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
phy-mode = "rgmii-id";
#address-cells = <1>;
#size-cells = <0>;
@@ -555,7 +555,7 @@
clock-names = "clkp1", "clkp2", "can_clk";
assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>;
assigned-clock-rates = <40000000>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -570,7 +570,7 @@
clock-names = "clkp1", "clkp2", "can_clk";
assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>;
assigned-clock-rates = <40000000>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -586,7 +586,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x31>, <&dmac1 0x30>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -602,7 +602,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x33>, <&dmac1 0x32>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -618,7 +618,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x35>, <&dmac1 0x34>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -634,7 +634,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x37>, <&dmac0 0x36>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -650,7 +650,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x39>, <&dmac0 0x38>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -665,7 +665,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x51>, <&dmac1 0x50>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -680,7 +680,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x53>, <&dmac1 0x52>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -695,7 +695,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x13>, <&dmac1 0x12>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -710,7 +710,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x57>, <&dmac0 0x56>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -725,7 +725,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x59>, <&dmac0 0x58>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -740,7 +740,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac1 0x5b>, <&dmac1 0x5a>;
dma-names = "tx", "rx";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -751,7 +751,7 @@
reg = <0 0xe6500000 0 0x40>;
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 931>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -763,7 +763,7 @@
reg = <0 0xe6508000 0 0x40>;
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 930>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -775,7 +775,7 @@
reg = <0 0xe6510000 0 0x40>;
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 929>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -787,7 +787,7 @@
reg = <0 0xe66d0000 0 0x40>;
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 928>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -799,7 +799,7 @@
reg = <0 0xe66d8000 0 0x40>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 927>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -811,7 +811,7 @@
reg = <0 0xe66e0000 0 0x40>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 919>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -823,7 +823,7 @@
reg = <0 0xe66e8000 0 0x40>;
interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 918>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -873,7 +873,7 @@
"src.1", "src.0",
"dvc.0", "dvc.1",
"clk_a", "clk_b", "clk_c", "clk_i";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
rcar_sound,dvc {
@@ -1007,7 +1007,7 @@
reg = <0 0xee000000 0 0xc00>;
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 328>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1016,7 +1016,7 @@
reg = <0 0xee040000 0 0xc00>;
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 327>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1028,7 +1028,7 @@
GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1";
clocks = <&cpg CPG_MOD 330>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <2>;
};
@@ -1041,7 +1041,7 @@
GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1";
clocks = <&cpg CPG_MOD 331>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <2>;
};
@@ -1051,7 +1051,7 @@
reg = <0 0xee100000 0 0x2000>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 314>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1060,7 +1060,7 @@
reg = <0 0xee120000 0 0x2000>;
interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 313>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1069,7 +1069,7 @@
reg = <0 0xee140000 0 0x2000>;
interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 312>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
cap-mmc-highspeed;
status = "disabled";
};
@@ -1079,7 +1079,7 @@
reg = <0 0xee160000 0 0x2000>;
interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 311>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
cap-mmc-highspeed;
status = "disabled";
};
@@ -1089,7 +1089,7 @@
reg = <0 0xee080200 0 0x700>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 703>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#phy-cells = <0>;
status = "disabled";
};
@@ -1098,7 +1098,7 @@
compatible = "renesas,usb2-phy-r8a7795";
reg = <0 0xee0a0200 0 0x700>;
clocks = <&cpg CPG_MOD 702>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#phy-cells = <0>;
status = "disabled";
};
@@ -1107,7 +1107,7 @@
compatible = "renesas,usb2-phy-r8a7795";
reg = <0 0xee0c0200 0 0x700>;
clocks = <&cpg CPG_MOD 701>;
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
#phy-cells = <0>;
status = "disabled";
};
@@ -1119,7 +1119,7 @@
clocks = <&cpg CPG_MOD 703>;
phys = <&usb2_phy0>;
phy-names = "usb";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1130,7 +1130,7 @@
clocks = <&cpg CPG_MOD 702>;
phys = <&usb2_phy1>;
phy-names = "usb";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1141,7 +1141,7 @@
clocks = <&cpg CPG_MOD 701>;
phys = <&usb2_phy2>;
phy-names = "usb";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1152,7 +1152,7 @@
clocks = <&cpg CPG_MOD 703>;
phys = <&usb2_phy0>;
phy-names = "usb";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1163,7 +1163,7 @@
clocks = <&cpg CPG_MOD 702>;
phys = <&usb2_phy1>;
phy-names = "usb";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1174,7 +1174,7 @@
clocks = <&cpg CPG_MOD 701>;
phys = <&usb2_phy2>;
phy-names = "usb";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
pciec0: pcie@fe000000 {
@@ -1198,7 +1198,7 @@
interrupt-map = <0 0 0 0 &gic GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 319>, <&pcie_bus_clk>;
clock-names = "pcie", "pcie_bus";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1223,7 +1223,7 @@
interrupt-map = <0 0 0 0 &gic GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 318>, <&pcie_bus_clk>;
clock-names = "pcie", "pcie_bus";
- power-domains = <&cpg>;
+ power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
status = "disabled";
};
};
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 03/12] ARM: dts: r8a7779: Add SYSC PM Domains
2016-04-22 9:07 ` Geert Uytterhoeven
` (2 preceding siblings ...)
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Add a device node for the System Controller.
Hook up ARM CPU cores 1-3 to their respective PM Domains.
Note that ARM CPU core 0 cannot be shut off.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
v2:
- Correct sysc "reg" property (#address/size-cells = 1, not 2),
- Change one-line summary prefix to match current arm-soc practices,
- Update compatible values.
---
arch/arm/boot/dts/r8a7779.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7779.dtsi b/arch/arm/boot/dts/r8a7779.dtsi
index 5c1d48d712a18652..e02875a8c040f304 100644
--- a/arch/arm/boot/dts/r8a7779.dtsi
+++ b/arch/arm/boot/dts/r8a7779.dtsi
@@ -14,6 +14,7 @@
#include <dt-bindings/clock/r8a7779-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/r8a7779-sysc.h>
/ {
compatible = "renesas,r8a7779";
@@ -34,18 +35,21 @@
compatible = "arm,cortex-a9";
reg = <1>;
clock-frequency = <1000000000>;
+ power-domains = <&sysc R8A7779_PD_ARM1>;
};
cpu@2 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <2>;
clock-frequency = <1000000000>;
+ power-domains = <&sysc R8A7779_PD_ARM2>;
};
cpu@3 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <3>;
clock-frequency = <1000000000>;
+ power-domains = <&sysc R8A7779_PD_ARM3>;
};
};
@@ -586,4 +590,10 @@
"mmc1", "mmc0";
};
};
+
+ sysc: system-controller@ffd85000 {
+ compatible = "renesas,r8a7779-sysc";
+ reg = <0xffd85000 0x0200>;
+ #power-domain-cells = <1>;
+ };
};
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 04/12] ARM: dts: r8a7790: Add SYSC PM Domains
2016-04-22 9:07 ` Geert Uytterhoeven
` (3 preceding siblings ...)
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Add a device node for the System Controller.
Hook up the Cortex-A15 and Cortex-A7 CPU cores and L2 caches/SCUs to
their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
- Drop fallback compatibility strings,
v2:
- Change one-line summary prefix to match current arm-soc practices,
- Update compatible values.
---
arch/arm/boot/dts/r8a7790.dtsi | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 776a2aed81d2eff1..36c91d921771336a 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -13,6 +13,7 @@
#include <dt-bindings/clock/r8a7790-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/r8a7790-sysc.h>
/ {
compatible = "renesas,r8a7790";
@@ -52,6 +53,7 @@
voltage-tolerance = <1>; /* 1% */
clocks = <&cpg_clocks R8A7790_CLK_Z>;
clock-latency = <300000>; /* 300 us */
+ power-domains = <&sysc R8A7790_PD_CA15_CPU0>;
next-level-cache = <&L2_CA15>;
/* kHz - uV - OPPs unknown yet */
@@ -68,6 +70,7 @@
compatible = "arm,cortex-a15";
reg = <1>;
clock-frequency = <1300000000>;
+ power-domains = <&sysc R8A7790_PD_CA15_CPU1>;
next-level-cache = <&L2_CA15>;
};
@@ -76,6 +79,7 @@
compatible = "arm,cortex-a15";
reg = <2>;
clock-frequency = <1300000000>;
+ power-domains = <&sysc R8A7790_PD_CA15_CPU2>;
next-level-cache = <&L2_CA15>;
};
@@ -84,6 +88,7 @@
compatible = "arm,cortex-a15";
reg = <3>;
clock-frequency = <1300000000>;
+ power-domains = <&sysc R8A7790_PD_CA15_CPU3>;
next-level-cache = <&L2_CA15>;
};
@@ -92,6 +97,7 @@
compatible = "arm,cortex-a7";
reg = <0x100>;
clock-frequency = <780000000>;
+ power-domains = <&sysc R8A7790_PD_CA7_CPU0>;
next-level-cache = <&L2_CA7>;
};
@@ -100,6 +106,7 @@
compatible = "arm,cortex-a7";
reg = <0x101>;
clock-frequency = <780000000>;
+ power-domains = <&sysc R8A7790_PD_CA7_CPU1>;
next-level-cache = <&L2_CA7>;
};
@@ -108,6 +115,7 @@
compatible = "arm,cortex-a7";
reg = <0x102>;
clock-frequency = <780000000>;
+ power-domains = <&sysc R8A7790_PD_CA7_CPU2>;
next-level-cache = <&L2_CA7>;
};
@@ -116,6 +124,7 @@
compatible = "arm,cortex-a7";
reg = <0x103>;
clock-frequency = <780000000>;
+ power-domains = <&sysc R8A7790_PD_CA7_CPU3>;
next-level-cache = <&L2_CA7>;
};
};
@@ -141,12 +150,14 @@
L2_CA15: cache-controller@0 {
compatible = "cache";
+ power-domains = <&sysc R8A7790_PD_CA15_SCU>;
cache-unified;
cache-level = <2>;
};
L2_CA7: cache-controller@1 {
compatible = "cache";
+ power-domains = <&sysc R8A7790_PD_CA7_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -1450,6 +1461,12 @@
};
};
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7790-sysc";
+ reg = <0 0xe6180000 0 0x0200>;
+ #power-domain-cells = <1>;
+ };
+
qspi: spi@e6b10000 {
compatible = "renesas,qspi-r8a7790", "renesas,qspi";
reg = <0 0xe6b10000 0 0x2c>;
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 05/12] ARM: dts: r8a7791: Add SYSC PM Domains
2016-04-22 9:07 ` Geert Uytterhoeven
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-pm-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, Geert Uytterhoeven
Add a device node for the System Controller.
Hook up the Cortex-A15 CPU cores and the Cortex-A15 L2 cache/SCU to
their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
Acked-by: Laurent Pinchart <laurent.pinchart-ryLnwIuWjnjg/C1BVhZhaw@public.gmane.org>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
- Drop fallback compatibility strings,
v2:
- Change one-line summary prefix to match current arm-soc practices,
- Update compatible values.
---
arch/arm/boot/dts/r8a7791.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 565c270e549d2bb6..b8657f4b45efdfe5 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -13,6 +13,7 @@
#include <dt-bindings/clock/r8a7791-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/r8a7791-sysc.h>
/ {
compatible = "renesas,r8a7791";
@@ -51,6 +52,7 @@
voltage-tolerance = <1>; /* 1% */
clocks = <&cpg_clocks R8A7791_CLK_Z>;
clock-latency = <300000>; /* 300 us */
+ power-domains = <&sysc R8A7791_PD_CA15_CPU0>;
next-level-cache = <&L2_CA15>;
/* kHz - uV - OPPs unknown yet */
@@ -67,6 +69,7 @@
compatible = "arm,cortex-a15";
reg = <1>;
clock-frequency = <1500000000>;
+ power-domains = <&sysc R8A7791_PD_CA15_CPU1>;
next-level-cache = <&L2_CA15>;
};
};
@@ -92,6 +95,7 @@
L2_CA15: cache-controller@0 {
compatible = "cache";
+ power-domains = <&sysc R8A7791_PD_CA15_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -1463,6 +1467,12 @@
};
};
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7791-sysc";
+ reg = <0 0xe6180000 0 0x0200>;
+ #power-domain-cells = <1>;
+ };
+
qspi: spi@e6b10000 {
compatible = "renesas,qspi-r8a7791", "renesas,qspi";
reg = <0 0xe6b10000 0 0x2c>;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 05/12] ARM: dts: r8a7791: Add SYSC PM Domains
@ 2016-04-22 9:07 ` Geert Uytterhoeven
0 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Add a device node for the System Controller.
Hook up the Cortex-A15 CPU cores and the Cortex-A15 L2 cache/SCU to
their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
- Drop fallback compatibility strings,
v2:
- Change one-line summary prefix to match current arm-soc practices,
- Update compatible values.
---
arch/arm/boot/dts/r8a7791.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 565c270e549d2bb6..b8657f4b45efdfe5 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -13,6 +13,7 @@
#include <dt-bindings/clock/r8a7791-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/r8a7791-sysc.h>
/ {
compatible = "renesas,r8a7791";
@@ -51,6 +52,7 @@
voltage-tolerance = <1>; /* 1% */
clocks = <&cpg_clocks R8A7791_CLK_Z>;
clock-latency = <300000>; /* 300 us */
+ power-domains = <&sysc R8A7791_PD_CA15_CPU0>;
next-level-cache = <&L2_CA15>;
/* kHz - uV - OPPs unknown yet */
@@ -67,6 +69,7 @@
compatible = "arm,cortex-a15";
reg = <1>;
clock-frequency = <1500000000>;
+ power-domains = <&sysc R8A7791_PD_CA15_CPU1>;
next-level-cache = <&L2_CA15>;
};
};
@@ -92,6 +95,7 @@
L2_CA15: cache-controller@0 {
compatible = "cache";
+ power-domains = <&sysc R8A7791_PD_CA15_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -1463,6 +1467,12 @@
};
};
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7791-sysc";
+ reg = <0 0xe6180000 0 0x0200>;
+ #power-domain-cells = <1>;
+ };
+
qspi: spi@e6b10000 {
compatible = "renesas,qspi-r8a7791", "renesas,qspi";
reg = <0 0xe6b10000 0 0x2c>;
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 06/12] ARM: dts: r8a7793: Add SYSC PM Domains
2016-04-22 9:07 ` Geert Uytterhoeven
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: devicetree, Geert Uytterhoeven, linux-pm, linux-renesas-soc,
Laurent Pinchart, linux-arm-kernel
Add a device node for the System Controller.
Hook up the first Cortex-A15 CPU core and the Cortex-A15 L2 cache/SCU to
their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
- Drop fallback compatibility strings,
v2:
- Change one-line summary prefix to match current arm-soc practices,
- Update compatible values.
---
arch/arm/boot/dts/r8a7793.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 6186179fd66db6b2..53e235e3279d08c1 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/clock/r8a7793-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/r8a7793-sysc.h>
/ {
compatible = "renesas,r8a7793";
@@ -43,6 +44,7 @@
voltage-tolerance = <1>; /* 1% */
clocks = <&cpg_clocks R8A7793_CLK_Z>;
clock-latency = <300000>; /* 300 us */
+ power-domains = <&sysc R8A7793_PD_CA15_CPU0>;
/* kHz - uV - OPPs unknown yet */
operating-points = <1500000 1000000>,
@@ -76,6 +78,7 @@
L2_CA15: cache-controller@0 {
compatible = "cache";
+ power-domains = <&sysc R8A7793_PD_CA15_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -1223,6 +1226,12 @@
};
};
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7793-sysc";
+ reg = <0 0xe6180000 0 0x0200>;
+ #power-domain-cells = <1>;
+ };
+
ipmmu_sy0: mmu@e6280000 {
compatible = "renesas,ipmmu-r8a7793", "renesas,ipmmu-vmsa";
reg = <0 0xe6280000 0 0x1000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 06/12] ARM: dts: r8a7793: Add SYSC PM Domains
@ 2016-04-22 9:07 ` Geert Uytterhoeven
0 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Add a device node for the System Controller.
Hook up the first Cortex-A15 CPU core and the Cortex-A15 L2 cache/SCU to
their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
- Drop fallback compatibility strings,
v2:
- Change one-line summary prefix to match current arm-soc practices,
- Update compatible values.
---
arch/arm/boot/dts/r8a7793.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 6186179fd66db6b2..53e235e3279d08c1 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/clock/r8a7793-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/r8a7793-sysc.h>
/ {
compatible = "renesas,r8a7793";
@@ -43,6 +44,7 @@
voltage-tolerance = <1>; /* 1% */
clocks = <&cpg_clocks R8A7793_CLK_Z>;
clock-latency = <300000>; /* 300 us */
+ power-domains = <&sysc R8A7793_PD_CA15_CPU0>;
/* kHz - uV - OPPs unknown yet */
operating-points = <1500000 1000000>,
@@ -76,6 +78,7 @@
L2_CA15: cache-controller@0 {
compatible = "cache";
+ power-domains = <&sysc R8A7793_PD_CA15_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -1223,6 +1226,12 @@
};
};
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7793-sysc";
+ reg = <0 0xe6180000 0 0x0200>;
+ #power-domain-cells = <1>;
+ };
+
ipmmu_sy0: mmu@e6280000 {
compatible = "renesas,ipmmu-r8a7793", "renesas,ipmmu-vmsa";
reg = <0 0xe6280000 0 0x1000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 06/12] ARM: dts: r8a7793: Add SYSC PM Domains
@ 2016-04-22 9:07 ` Geert Uytterhoeven
0 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: linux-arm-kernel
Add a device node for the System Controller.
Hook up the first Cortex-A15 CPU core and the Cortex-A15 L2 cache/SCU to
their respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
- Drop fallback compatibility strings,
v2:
- Change one-line summary prefix to match current arm-soc practices,
- Update compatible values.
---
arch/arm/boot/dts/r8a7793.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 6186179fd66db6b2..53e235e3279d08c1 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/clock/r8a7793-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/r8a7793-sysc.h>
/ {
compatible = "renesas,r8a7793";
@@ -43,6 +44,7 @@
voltage-tolerance = <1>; /* 1% */
clocks = <&cpg_clocks R8A7793_CLK_Z>;
clock-latency = <300000>; /* 300 us */
+ power-domains = <&sysc R8A7793_PD_CA15_CPU0>;
/* kHz - uV - OPPs unknown yet */
operating-points = <1500000 1000000>,
@@ -76,6 +78,7 @@
L2_CA15: cache-controller at 0 {
compatible = "cache";
+ power-domains = <&sysc R8A7793_PD_CA15_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -1223,6 +1226,12 @@
};
};
+ sysc: system-controller at e6180000 {
+ compatible = "renesas,r8a7793-sysc";
+ reg = <0 0xe6180000 0 0x0200>;
+ #power-domain-cells = <1>;
+ };
+
ipmmu_sy0: mmu at e6280000 {
compatible = "renesas,ipmmu-r8a7793", "renesas,ipmmu-vmsa";
reg = <0 0xe6280000 0 0x1000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 07/12] ARM: dts: r8a7794: Add SYSC PM Domains
2016-04-22 9:07 ` Geert Uytterhoeven
` (6 preceding siblings ...)
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Add a device node for the System Controller.
Hook up the Cortex-A7 CPU cores and the Cortex-A7 L2 cache/SCU to their
respective PM Domains.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Add Acked-by,
v5:
- Remove "power-domains" property again from the sysc node, as the
System Controller itself is not part of the Clock Domain,
v4:
- Add "power-domains" property to the sysc node, to refer to the SoC's
Clock Domain,
v3:
- Drop power area hiearchy from DT,
- Switch to "#power-domain-cells = <1>",
- Drop fallback compatibility strings,
v2:
- Change one-line summary prefix to match current arm-soc practices,
- Update compatible values.
---
arch/arm/boot/dts/r8a7794.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index b0bce43779f14b0d..70eff80a813ec85a 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -12,6 +12,7 @@
#include <dt-bindings/clock/r8a7794-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/power/r8a7794-sysc.h>
/ {
compatible = "renesas,r8a7794";
@@ -42,6 +43,7 @@
compatible = "arm,cortex-a7";
reg = <0>;
clock-frequency = <1000000000>;
+ power-domains = <&sysc R8A7794_PD_CA7_CPU0>;
next-level-cache = <&L2_CA7>;
};
@@ -50,12 +52,14 @@
compatible = "arm,cortex-a7";
reg = <1>;
clock-frequency = <1000000000>;
+ power-domains = <&sysc R8A7794_PD_CA7_CPU1>;
next-level-cache = <&L2_CA7>;
};
};
L2_CA7: cache-controller@1 {
compatible = "cache";
+ power-domains = <&sysc R8A7794_PD_CA7_SCU>;
cache-unified;
cache-level = <2>;
};
@@ -1215,6 +1219,12 @@
};
};
+ sysc: system-controller@e6180000 {
+ compatible = "renesas,r8a7794-sysc";
+ reg = <0 0xe6180000 0 0x0200>;
+ #power-domain-cells = <1>;
+ };
+
ipmmu_sy0: mmu@e6280000 {
compatible = "renesas,ipmmu-r8a7794", "renesas,ipmmu-vmsa";
reg = <0 0xe6280000 0 0x1000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 08/12] ARM: dts: r8a7779: Use SYSC "always-on" PM Domain
2016-04-22 9:07 ` Geert Uytterhoeven
` (7 preceding siblings ...)
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Hook up all devices that are part of the CPG/MSTP Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- No changes,
v5:
- Add Acked-by,
v4:
- New.
---
arch/arm/boot/dts/r8a7779.dtsi | 44 +++++++++++++++++++++---------------------
1 file changed, 22 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7779.dtsi b/arch/arm/boot/dts/r8a7779.dtsi
index e02875a8c040f304..d43e3b2105aef7dc 100644
--- a/arch/arm/boot/dts/r8a7779.dtsi
+++ b/arch/arm/boot/dts/r8a7779.dtsi
@@ -177,7 +177,7 @@
reg = <0xffc70000 0x1000>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7779_CLK_I2C0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -188,7 +188,7 @@
reg = <0xffc71000 0x1000>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7779_CLK_I2C1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -199,7 +199,7 @@
reg = <0xffc72000 0x1000>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7779_CLK_I2C2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -210,7 +210,7 @@
reg = <0xffc73000 0x1000>;
interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7779_CLK_I2C3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -222,7 +222,7 @@
clocks = <&mstp0_clks R8A7779_CLK_SCIF0>,
<&cpg_clocks R8A7779_CLK_S1>, <&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -234,7 +234,7 @@
clocks = <&mstp0_clks R8A7779_CLK_SCIF1>,
<&cpg_clocks R8A7779_CLK_S1>, <&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -246,7 +246,7 @@
clocks = <&mstp0_clks R8A7779_CLK_SCIF2>,
<&cpg_clocks R8A7779_CLK_S1>, <&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -258,7 +258,7 @@
clocks = <&mstp0_clks R8A7779_CLK_SCIF3>,
<&cpg_clocks R8A7779_CLK_S1>, <&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -270,7 +270,7 @@
clocks = <&mstp0_clks R8A7779_CLK_SCIF4>,
<&cpg_clocks R8A7779_CLK_S1>, <&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -282,7 +282,7 @@
clocks = <&mstp0_clks R8A7779_CLK_SCIF5>,
<&cpg_clocks R8A7779_CLK_S1>, <&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -304,7 +304,7 @@
<GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7779_CLK_TMU0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
#renesas,channels = <3>;
@@ -319,7 +319,7 @@
<GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7779_CLK_TMU1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
#renesas,channels = <3>;
@@ -334,7 +334,7 @@
<GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7779_CLK_TMU2>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
#renesas,channels = <3>;
@@ -346,7 +346,7 @@
reg = <0xfc600000 0x2000>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7779_CLK_SATA>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
};
sdhi0: sd@ffe4c000 {
@@ -354,7 +354,7 @@
reg = <0xffe4c000 0x100>;
interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7779_CLK_SDHI0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -363,7 +363,7 @@
reg = <0xffe4d000 0x100>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7779_CLK_SDHI1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -372,7 +372,7 @@
reg = <0xffe4e000 0x100>;
interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7779_CLK_SDHI2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -381,7 +381,7 @@
reg = <0xffe4f000 0x100>;
interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7779_CLK_SDHI3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -392,7 +392,7 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&mstp0_clks R8A7779_CLK_HSPI>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -403,7 +403,7 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&mstp0_clks R8A7779_CLK_HSPI>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -414,7 +414,7 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&mstp0_clks R8A7779_CLK_HSPI>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -423,7 +423,7 @@
reg = <0 0xfff80000 0 0x40000>;
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7779_CLK_DU>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7779_PD_ALWAYS_ON>;
status = "disabled";
ports {
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 09/12] ARM: dts: r8a7790: Use SYSC "always-on" PM Domain
2016-04-22 9:07 ` Geert Uytterhoeven
` (8 preceding siblings ...)
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Hook up all devices that are part of the CPG/MSTP Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Rebased,
v5:
- Add Acked-by,
v4:
- New.
---
arch/arm/boot/dts/r8a7790.dtsi | 138 ++++++++++++++++++++---------------------
1 file changed, 69 insertions(+), 69 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 36c91d921771336a..dc8497b1558677ea 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -184,7 +184,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7790_CLK_GPIO0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
};
gpio1: gpio@e6051000 {
@@ -197,7 +197,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7790_CLK_GPIO1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
};
gpio2: gpio@e6052000 {
@@ -210,7 +210,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7790_CLK_GPIO2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
};
gpio3: gpio@e6053000 {
@@ -223,7 +223,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7790_CLK_GPIO3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
};
gpio4: gpio@e6054000 {
@@ -236,7 +236,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7790_CLK_GPIO4>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
};
gpio5: gpio@e6055000 {
@@ -249,7 +249,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7790_CLK_GPIO5>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
};
thermal: thermal@e61f0000 {
@@ -259,7 +259,7 @@
reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp5_clks R8A7790_CLK_THERMAL>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#thermal-sensor-cells = <0>;
};
@@ -278,7 +278,7 @@
<GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7790_CLK_CMT0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
renesas,channels-mask = <0x60>;
@@ -298,7 +298,7 @@
<GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_CMT1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
renesas,channels-mask = <0xff>;
@@ -315,7 +315,7 @@
<GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp4_clks R8A7790_CLK_IRQC>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
};
dmac0: dma-controller@e6700000 {
@@ -344,7 +344,7 @@
"ch12", "ch13", "ch14";
clocks = <&mstp2_clks R8A7790_CLK_SYS_DMAC0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <15>;
};
@@ -375,7 +375,7 @@
"ch12", "ch13", "ch14";
clocks = <&mstp2_clks R8A7790_CLK_SYS_DMAC1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <15>;
};
@@ -404,7 +404,7 @@
"ch12";
clocks = <&mstp5_clks R8A7790_CLK_AUDIO_DMAC0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <13>;
};
@@ -433,7 +433,7 @@
"ch12";
clocks = <&mstp5_clks R8A7790_CLK_AUDIO_DMAC1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <13>;
};
@@ -445,7 +445,7 @@
GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1";
clocks = <&mstp3_clks R8A7790_CLK_USBDMAC0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <2>;
};
@@ -457,7 +457,7 @@
GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1";
clocks = <&mstp3_clks R8A7790_CLK_USBDMAC1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <2>;
};
@@ -469,7 +469,7 @@
reg = <0 0xe6508000 0 0x40>;
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7790_CLK_I2C0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -481,7 +481,7 @@
reg = <0 0xe6518000 0 0x40>;
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7790_CLK_I2C1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -493,7 +493,7 @@
reg = <0 0xe6530000 0 0x40>;
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7790_CLK_I2C2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -505,7 +505,7 @@
reg = <0 0xe6540000 0 0x40>;
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7790_CLK_I2C3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -519,7 +519,7 @@
clocks = <&mstp3_clks R8A7790_CLK_IIC0>;
dmas = <&dmac0 0x61>, <&dmac0 0x62>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -532,7 +532,7 @@
clocks = <&mstp3_clks R8A7790_CLK_IIC1>;
dmas = <&dmac0 0x65>, <&dmac0 0x66>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -545,7 +545,7 @@
clocks = <&mstp3_clks R8A7790_CLK_IIC2>;
dmas = <&dmac0 0x69>, <&dmac0 0x6a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -558,7 +558,7 @@
clocks = <&mstp9_clks R8A7790_CLK_IICDVFS>;
dmas = <&dmac0 0x77>, <&dmac0 0x78>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -569,7 +569,7 @@
clocks = <&mstp3_clks R8A7790_CLK_MMCIF0>;
dmas = <&dmac0 0xd1>, <&dmac0 0xd2>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
reg-io-width = <4>;
status = "disabled";
max-frequency = <97500000>;
@@ -582,7 +582,7 @@
clocks = <&mstp3_clks R8A7790_CLK_MMCIF1>;
dmas = <&dmac0 0xe1>, <&dmac0 0xe2>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
reg-io-width = <4>;
status = "disabled";
max-frequency = <97500000>;
@@ -601,7 +601,7 @@
dmas = <&dmac1 0xcd>, <&dmac1 0xce>;
dma-names = "tx", "rx";
max-frequency = <195000000>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -613,7 +613,7 @@
dmas = <&dmac1 0xc9>, <&dmac1 0xca>;
dma-names = "tx", "rx";
max-frequency = <195000000>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -625,7 +625,7 @@
dmas = <&dmac1 0xc1>, <&dmac1 0xc2>;
dma-names = "tx", "rx";
max-frequency = <97500000>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -637,7 +637,7 @@
dmas = <&dmac1 0xd3>, <&dmac1 0xd4>;
dma-names = "tx", "rx";
max-frequency = <97500000>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -650,7 +650,7 @@
clock-names = "fck";
dmas = <&dmac0 0x21>, <&dmac0 0x22>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -663,7 +663,7 @@
clock-names = "fck";
dmas = <&dmac0 0x25>, <&dmac0 0x26>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -676,7 +676,7 @@
clock-names = "fck";
dmas = <&dmac0 0x27>, <&dmac0 0x28>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -689,7 +689,7 @@
clock-names = "fck";
dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -702,7 +702,7 @@
clock-names = "fck";
dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -715,7 +715,7 @@
clock-names = "fck";
dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -729,7 +729,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -743,7 +743,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -757,7 +757,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -771,7 +771,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -785,7 +785,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -794,7 +794,7 @@
reg = <0 0xee700000 0 0x400>;
interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7790_CLK_ETHER>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
phy-mode = "rmii";
#address-cells = <1>;
#size-cells = <0>;
@@ -807,7 +807,7 @@
reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7790_CLK_ETHERAVB>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -818,7 +818,7 @@
reg = <0 0xee300000 0 0x2000>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7790_CLK_SATA0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -827,7 +827,7 @@
reg = <0 0xee500000 0 0x2000>;
interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7790_CLK_SATA1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -839,7 +839,7 @@
dmas = <&usb_dmac0 0>, <&usb_dmac0 1>,
<&usb_dmac1 0>, <&usb_dmac1 1>;
dma-names = "ch0", "ch1", "ch2", "ch3";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
renesas,buswait = <4>;
phys = <&usb0 1>;
phy-names = "usb";
@@ -853,7 +853,7 @@
#size-cells = <0>;
clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
clock-names = "usbhs";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
usb0: usb-channel@0 {
@@ -871,7 +871,7 @@
reg = <0 0xe6ef0000 0 0x1000>;
interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7790_CLK_VIN0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -880,7 +880,7 @@
reg = <0 0xe6ef1000 0 0x1000>;
interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7790_CLK_VIN1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -889,7 +889,7 @@
reg = <0 0xe6ef2000 0 0x1000>;
interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7790_CLK_VIN2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -898,7 +898,7 @@
reg = <0 0xe6ef3000 0 0x1000>;
interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7790_CLK_VIN3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -907,7 +907,7 @@
reg = <0 0xfe920000 0 0x8000>;
interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7790_CLK_VSP1_R>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
renesas,has-sru;
renesas,#rpf = <5>;
@@ -920,7 +920,7 @@
reg = <0 0xfe928000 0 0x8000>;
interrupts = <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7790_CLK_VSP1_S>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
renesas,has-lut;
renesas,has-sru;
@@ -934,7 +934,7 @@
reg = <0 0xfe930000 0 0x8000>;
interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7790_CLK_VSP1_DU0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
renesas,has-lif;
renesas,has-lut;
@@ -948,7 +948,7 @@
reg = <0 0xfe938000 0 0x8000>;
interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7790_CLK_VSP1_DU1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
renesas,has-lif;
renesas,has-lut;
@@ -1003,7 +1003,7 @@
clocks = <&mstp9_clks R8A7790_CLK_RCAN0>,
<&cpg_clocks R8A7790_CLK_RCAN>, <&can_clk>;
clock-names = "clkp1", "clkp2", "can_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1014,7 +1014,7 @@
clocks = <&mstp9_clks R8A7790_CLK_RCAN1>,
<&cpg_clocks R8A7790_CLK_RCAN>, <&can_clk>;
clock-names = "clkp1", "clkp2", "can_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1023,7 +1023,7 @@
reg = <0 0xfe980000 0 0x10300>;
interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7790_CLK_JPU>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
};
clocks {
@@ -1474,7 +1474,7 @@
clocks = <&mstp9_clks R8A7790_CLK_QSPI_MOD>;
dmas = <&dmac0 0x17>, <&dmac0 0x18>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
num-cs = <1>;
#address-cells = <1>;
#size-cells = <0>;
@@ -1488,7 +1488,7 @@
clocks = <&mstp0_clks R8A7790_CLK_MSIOF0>;
dmas = <&dmac0 0x51>, <&dmac0 0x52>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1501,7 +1501,7 @@
clocks = <&mstp2_clks R8A7790_CLK_MSIOF1>;
dmas = <&dmac0 0x55>, <&dmac0 0x56>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1514,7 +1514,7 @@
clocks = <&mstp2_clks R8A7790_CLK_MSIOF2>;
dmas = <&dmac0 0x41>, <&dmac0 0x42>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1527,7 +1527,7 @@
clocks = <&mstp2_clks R8A7790_CLK_MSIOF3>;
dmas = <&dmac0 0x45>, <&dmac0 0x46>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1538,7 +1538,7 @@
reg = <0 0xee000000 0 0xc00>;
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_SSUSB>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
phys = <&usb2 1>;
phy-names = "usb";
status = "disabled";
@@ -1551,7 +1551,7 @@
<0 0xee080000 0 0x1100>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
bus-range = <0 0>;
@@ -1586,7 +1586,7 @@
<0 0xee0a0000 0 0x1100>;
interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
bus-range = <1 1>;
@@ -1604,7 +1604,7 @@
compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2";
device_type = "pci";
clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
reg = <0 0xee0d0000 0 0xc00>,
<0 0xee0c0000 0 0x1100>;
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
@@ -1657,7 +1657,7 @@
interrupt-map = <0 0 0 0 &gic GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7790_CLK_PCIEC>, <&pcie_bus_clk>;
clock-names = "pcie", "pcie_bus";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1700,7 +1700,7 @@
"mix.0", "mix.1",
"dvc.0", "dvc.1",
"clk_a", "clk_b", "clk_c", "clk_i";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
status = "disabled";
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 10/12] ARM: dts: r8a7791: Use SYSC "always-on" PM Domain
2016-04-22 9:07 ` Geert Uytterhoeven
` (9 preceding siblings ...)
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Hook up all devices that are part of the CPG/MSTP Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Rebased,
v5:
- Add Acked-by,
v4:
- New.
---
arch/arm/boot/dts/r8a7791.dtsi | 146 ++++++++++++++++++++---------------------
1 file changed, 73 insertions(+), 73 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index b8657f4b45efdfe5..db67e342c58566fa 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -122,7 +122,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7791_CLK_GPIO0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
};
gpio1: gpio@e6051000 {
@@ -135,7 +135,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7791_CLK_GPIO1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
};
gpio2: gpio@e6052000 {
@@ -148,7 +148,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7791_CLK_GPIO2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
};
gpio3: gpio@e6053000 {
@@ -161,7 +161,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7791_CLK_GPIO3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
};
gpio4: gpio@e6054000 {
@@ -174,7 +174,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7791_CLK_GPIO4>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
};
gpio5: gpio@e6055000 {
@@ -187,7 +187,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7791_CLK_GPIO5>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
};
gpio6: gpio@e6055400 {
@@ -200,7 +200,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7791_CLK_GPIO6>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
};
gpio7: gpio@e6055800 {
@@ -213,7 +213,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7791_CLK_GPIO7>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
};
thermal: thermal@e61f0000 {
@@ -223,7 +223,7 @@
reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp5_clks R8A7791_CLK_THERMAL>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#thermal-sensor-cells = <0>;
};
@@ -242,7 +242,7 @@
<GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7791_CLK_CMT0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
renesas,channels-mask = <0x60>;
@@ -262,7 +262,7 @@
<GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7791_CLK_CMT1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
renesas,channels-mask = <0xff>;
@@ -285,7 +285,7 @@
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp4_clks R8A7791_CLK_IRQC>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
};
dmac0: dma-controller@e6700000 {
@@ -314,7 +314,7 @@
"ch12", "ch13", "ch14";
clocks = <&mstp2_clks R8A7791_CLK_SYS_DMAC0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <15>;
};
@@ -345,7 +345,7 @@
"ch12", "ch13", "ch14";
clocks = <&mstp2_clks R8A7791_CLK_SYS_DMAC1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <15>;
};
@@ -374,7 +374,7 @@
"ch12";
clocks = <&mstp5_clks R8A7791_CLK_AUDIO_DMAC0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <13>;
};
@@ -403,7 +403,7 @@
"ch12";
clocks = <&mstp5_clks R8A7791_CLK_AUDIO_DMAC1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <13>;
};
@@ -415,7 +415,7 @@
GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1";
clocks = <&mstp3_clks R8A7791_CLK_USBDMAC0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <2>;
};
@@ -427,7 +427,7 @@
GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1";
clocks = <&mstp3_clks R8A7791_CLK_USBDMAC1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <2>;
};
@@ -440,7 +440,7 @@
reg = <0 0xe6508000 0 0x40>;
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7791_CLK_I2C0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -452,7 +452,7 @@
reg = <0 0xe6518000 0 0x40>;
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7791_CLK_I2C1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -464,7 +464,7 @@
reg = <0 0xe6530000 0 0x40>;
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7791_CLK_I2C2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -476,7 +476,7 @@
reg = <0 0xe6540000 0 0x40>;
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7791_CLK_I2C3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -488,7 +488,7 @@
reg = <0 0xe6520000 0 0x40>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7791_CLK_I2C4>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -501,7 +501,7 @@
reg = <0 0xe6528000 0 0x40>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7791_CLK_I2C5>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -516,7 +516,7 @@
clocks = <&mstp9_clks R8A7791_CLK_IICDVFS>;
dmas = <&dmac0 0x77>, <&dmac0 0x78>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -529,7 +529,7 @@
clocks = <&mstp3_clks R8A7791_CLK_IIC0>;
dmas = <&dmac0 0x61>, <&dmac0 0x62>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -542,7 +542,7 @@
clocks = <&mstp3_clks R8A7791_CLK_IIC1>;
dmas = <&dmac0 0x65>, <&dmac0 0x66>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -558,7 +558,7 @@
clocks = <&mstp3_clks R8A7791_CLK_MMCIF0>;
dmas = <&dmac0 0xd1>, <&dmac0 0xd2>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
reg-io-width = <4>;
status = "disabled";
max-frequency = <97500000>;
@@ -571,7 +571,7 @@
clocks = <&mstp3_clks R8A7791_CLK_SDHI0>;
dmas = <&dmac1 0xcd>, <&dmac1 0xce>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -582,7 +582,7 @@
clocks = <&mstp3_clks R8A7791_CLK_SDHI1>;
dmas = <&dmac1 0xc1>, <&dmac1 0xc2>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -593,7 +593,7 @@
clocks = <&mstp3_clks R8A7791_CLK_SDHI2>;
dmas = <&dmac1 0xd3>, <&dmac1 0xd4>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -606,7 +606,7 @@
clock-names = "fck";
dmas = <&dmac0 0x21>, <&dmac0 0x22>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -619,7 +619,7 @@
clock-names = "fck";
dmas = <&dmac0 0x25>, <&dmac0 0x26>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -632,7 +632,7 @@
clock-names = "fck";
dmas = <&dmac0 0x27>, <&dmac0 0x28>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -645,7 +645,7 @@
clock-names = "fck";
dmas = <&dmac0 0x1b>, <&dmac0 0x1c>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -658,7 +658,7 @@
clock-names = "fck";
dmas = <&dmac0 0x1f>, <&dmac0 0x20>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -671,7 +671,7 @@
clock-names = "fck";
dmas = <&dmac0 0x23>, <&dmac0 0x24>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -684,7 +684,7 @@
clock-names = "fck";
dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -697,7 +697,7 @@
clock-names = "fck";
dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -710,7 +710,7 @@
clock-names = "fck";
dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -724,7 +724,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -738,7 +738,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -752,7 +752,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -766,7 +766,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2f>, <&dmac0 0x30>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -780,7 +780,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0xfb>, <&dmac0 0xfc>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -794,7 +794,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0xfd>, <&dmac0 0xfe>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -808,7 +808,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -822,7 +822,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -836,7 +836,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x3b>, <&dmac0 0x3c>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -845,7 +845,7 @@
reg = <0 0xee700000 0 0x400>;
interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7791_CLK_ETHER>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
phy-mode = "rmii";
#address-cells = <1>;
#size-cells = <0>;
@@ -858,7 +858,7 @@
reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7791_CLK_ETHERAVB>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -869,7 +869,7 @@
reg = <0 0xee300000 0 0x2000>;
interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7791_CLK_SATA0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -878,7 +878,7 @@
reg = <0 0xee500000 0 0x2000>;
interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7791_CLK_SATA1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -890,7 +890,7 @@
dmas = <&usb_dmac0 0>, <&usb_dmac0 1>,
<&usb_dmac1 0>, <&usb_dmac1 1>;
dma-names = "ch0", "ch1", "ch2", "ch3";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
renesas,buswait = <4>;
phys = <&usb0 1>;
phy-names = "usb";
@@ -904,7 +904,7 @@
#size-cells = <0>;
clocks = <&mstp7_clks R8A7791_CLK_HSUSB>;
clock-names = "usbhs";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
usb0: usb-channel@0 {
@@ -922,7 +922,7 @@
reg = <0 0xe6ef0000 0 0x1000>;
interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7791_CLK_VIN0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -931,7 +931,7 @@
reg = <0 0xe6ef1000 0 0x1000>;
interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7791_CLK_VIN1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -940,7 +940,7 @@
reg = <0 0xe6ef2000 0 0x1000>;
interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7791_CLK_VIN2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -949,7 +949,7 @@
reg = <0 0xfe928000 0 0x8000>;
interrupts = <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7791_CLK_VSP1_S>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
renesas,has-lut;
renesas,has-sru;
@@ -963,7 +963,7 @@
reg = <0 0xfe930000 0 0x8000>;
interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7791_CLK_VSP1_DU0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
renesas,has-lif;
renesas,has-lut;
@@ -977,7 +977,7 @@
reg = <0 0xfe938000 0 0x8000>;
interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7791_CLK_VSP1_DU1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
renesas,has-lif;
renesas,has-lut;
@@ -1023,7 +1023,7 @@
clocks = <&mstp9_clks R8A7791_CLK_RCAN0>,
<&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>;
clock-names = "clkp1", "clkp2", "can_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1034,7 +1034,7 @@
clocks = <&mstp9_clks R8A7791_CLK_RCAN1>,
<&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>;
clock-names = "clkp1", "clkp2", "can_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1043,7 +1043,7 @@
reg = <0 0xfe980000 0 0x10300>;
interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7791_CLK_JPU>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
};
clocks {
@@ -1480,7 +1480,7 @@
clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>;
dmas = <&dmac0 0x17>, <&dmac0 0x18>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
num-cs = <1>;
#address-cells = <1>;
#size-cells = <0>;
@@ -1494,7 +1494,7 @@
clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>;
dmas = <&dmac0 0x51>, <&dmac0 0x52>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1507,7 +1507,7 @@
clocks = <&mstp2_clks R8A7791_CLK_MSIOF1>;
dmas = <&dmac0 0x55>, <&dmac0 0x56>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1520,7 +1520,7 @@
clocks = <&mstp2_clks R8A7791_CLK_MSIOF2>;
dmas = <&dmac0 0x41>, <&dmac0 0x42>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -1531,7 +1531,7 @@
reg = <0 0xee000000 0 0xc00>;
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7791_CLK_SSUSB>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
phys = <&usb2 1>;
phy-names = "usb";
status = "disabled";
@@ -1544,7 +1544,7 @@
<0 0xee080000 0 0x1100>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7791_CLK_EHCI>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
bus-range = <0 0>;
@@ -1579,7 +1579,7 @@
<0 0xee0c0000 0 0x1100>;
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7791_CLK_EHCI>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
bus-range = <1 1>;
@@ -1629,7 +1629,7 @@
interrupt-map = <0 0 0 0 &gic GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7791_CLK_PCIEC>, <&pcie_bus_clk>;
clock-names = "pcie", "pcie_bus";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1732,7 +1732,7 @@
"mix.0", "mix.1",
"dvc.0", "dvc.1",
"clk_a", "clk_b", "clk_c", "clk_i";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
status = "disabled";
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 11/12] ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
2016-04-22 9:07 ` Geert Uytterhoeven
` (10 preceding siblings ...)
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Hook up all devices that are part of the CPG/MSTP Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Rebased,
- Use "<&sysc R8A7793_PD_ALWAYS_ON>" for recently added sdhi[0-2]
device nodes,
v5:
- Add Acked-by,
v4:
- New.
---
arch/arm/boot/dts/r8a7793.dtsi | 102 ++++++++++++++++++++---------------------
1 file changed, 51 insertions(+), 51 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 53e235e3279d08c1..2abf2e4896991bad 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -105,7 +105,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7793_CLK_GPIO0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
};
gpio1: gpio@e6051000 {
@@ -118,7 +118,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7793_CLK_GPIO1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
};
gpio2: gpio@e6052000 {
@@ -131,7 +131,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7793_CLK_GPIO2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
};
gpio3: gpio@e6053000 {
@@ -144,7 +144,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7793_CLK_GPIO3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
};
gpio4: gpio@e6054000 {
@@ -157,7 +157,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7793_CLK_GPIO4>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
};
gpio5: gpio@e6055000 {
@@ -170,7 +170,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7793_CLK_GPIO5>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
};
gpio6: gpio@e6055400 {
@@ -183,7 +183,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7793_CLK_GPIO6>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
};
gpio7: gpio@e6055800 {
@@ -196,7 +196,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7793_CLK_GPIO7>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
};
thermal: thermal@e61f0000 {
@@ -206,7 +206,7 @@
reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp5_clks R8A7793_CLK_THERMAL>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
#thermal-sensor-cells = <0>;
};
@@ -225,7 +225,7 @@
<GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7793_CLK_CMT0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
renesas,channels-mask = <0x60>;
@@ -245,7 +245,7 @@
<GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7793_CLK_CMT1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
renesas,channels-mask = <0xff>;
@@ -268,7 +268,7 @@
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp4_clks R8A7793_CLK_IRQC>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
};
dmac0: dma-controller@e6700000 {
@@ -297,7 +297,7 @@
"ch12", "ch13", "ch14";
clocks = <&mstp2_clks R8A7793_CLK_SYS_DMAC0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <15>;
};
@@ -328,7 +328,7 @@
"ch12", "ch13", "ch14";
clocks = <&mstp2_clks R8A7793_CLK_SYS_DMAC1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <15>;
};
@@ -357,7 +357,7 @@
"ch12";
clocks = <&mstp5_clks R8A7793_CLK_AUDIO_DMAC0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <13>;
};
@@ -386,7 +386,7 @@
"ch12";
clocks = <&mstp5_clks R8A7793_CLK_AUDIO_DMAC1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <13>;
};
@@ -399,7 +399,7 @@
reg = <0 0xe6508000 0 0x40>;
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7793_CLK_I2C0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -411,7 +411,7 @@
reg = <0 0xe6518000 0 0x40>;
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7793_CLK_I2C1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -423,7 +423,7 @@
reg = <0 0xe6530000 0 0x40>;
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7793_CLK_I2C2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -435,7 +435,7 @@
reg = <0 0xe6540000 0 0x40>;
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7793_CLK_I2C3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -447,7 +447,7 @@
reg = <0 0xe6520000 0 0x40>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7793_CLK_I2C4>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -460,7 +460,7 @@
reg = <0 0xe6528000 0 0x40>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7793_CLK_I2C5>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -475,7 +475,7 @@
clocks = <&mstp9_clks R8A7793_CLK_IICDVFS>;
dmas = <&dmac0 0x77>, <&dmac0 0x78>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -488,7 +488,7 @@
clocks = <&mstp3_clks R8A7793_CLK_IIC0>;
dmas = <&dmac0 0x61>, <&dmac0 0x62>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -501,7 +501,7 @@
clocks = <&mstp3_clks R8A7793_CLK_IIC1>;
dmas = <&dmac0 0x65>, <&dmac0 0x66>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -517,7 +517,7 @@
clocks = <&mstp3_clks R8A7793_CLK_SDHI0>;
dmas = <&dmac0 0xcd>, <&dmac0 0xce>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -528,7 +528,7 @@
clocks = <&mstp3_clks R8A7793_CLK_SDHI1>;
dmas = <&dmac0 0xc1>, <&dmac0 0xc2>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -539,7 +539,7 @@
clocks = <&mstp3_clks R8A7793_CLK_SDHI2>;
dmas = <&dmac0 0xd3>, <&dmac0 0xd4>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -552,7 +552,7 @@
clock-names = "fck";
dmas = <&dmac0 0x21>, <&dmac0 0x22>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -565,7 +565,7 @@
clock-names = "fck";
dmas = <&dmac0 0x25>, <&dmac0 0x26>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -578,7 +578,7 @@
clock-names = "fck";
dmas = <&dmac0 0x27>, <&dmac0 0x28>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -591,7 +591,7 @@
clock-names = "fck";
dmas = <&dmac0 0x1b>, <&dmac0 0x1c>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -604,7 +604,7 @@
clock-names = "fck";
dmas = <&dmac0 0x1f>, <&dmac0 0x20>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -617,7 +617,7 @@
clock-names = "fck";
dmas = <&dmac0 0x23>, <&dmac0 0x24>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -630,7 +630,7 @@
clock-names = "fck";
dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -643,7 +643,7 @@
clock-names = "fck";
dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -656,7 +656,7 @@
clock-names = "fck";
dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -670,7 +670,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -684,7 +684,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -698,7 +698,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -712,7 +712,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2f>, <&dmac0 0x30>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -726,7 +726,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0xfb>, <&dmac0 0xfc>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -740,7 +740,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0xfd>, <&dmac0 0xfe>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -754,7 +754,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -768,7 +768,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -782,7 +782,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x3b>, <&dmac0 0x3c>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -791,7 +791,7 @@
reg = <0 0xee700000 0 0x400>;
interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7793_CLK_ETHER>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
phy-mode = "rmii";
#address-cells = <1>;
#size-cells = <0>;
@@ -805,7 +805,7 @@
clocks = <&mstp9_clks R8A7793_CLK_QSPI_MOD>;
dmas = <&dmac0 0x17>, <&dmac0 0x18>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
num-cs = <1>;
#address-cells = <1>;
#size-cells = <0>;
@@ -849,7 +849,7 @@
clocks = <&mstp9_clks R8A7793_CLK_RCAN0>,
<&cpg_clocks R8A7793_CLK_RCAN>, <&can_clk>;
clock-names = "clkp1", "clkp2", "can_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -860,7 +860,7 @@
clocks = <&mstp9_clks R8A7793_CLK_RCAN1>,
<&cpg_clocks R8A7793_CLK_RCAN>, <&can_clk>;
clock-names = "clkp1", "clkp2", "can_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -1327,7 +1327,7 @@
"src.4", "src.3", "src.2", "src.1", "src.0",
"dvc.0", "dvc.1",
"clk_a", "clk_b", "clk_c", "clk_i";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
status = "disabled";
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* [PATCH v6 12/12] ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
2016-04-22 9:07 ` Geert Uytterhoeven
` (11 preceding siblings ...)
(?)
@ 2016-04-22 9:07 ` Geert Uytterhoeven
-1 siblings, 0 replies; 21+ messages in thread
From: Geert Uytterhoeven @ 2016-04-22 9:07 UTC (permalink / raw)
To: Simon Horman, Magnus Damm
Cc: Laurent Pinchart, linux-renesas-soc, linux-arm-kernel, linux-pm,
devicetree, Geert Uytterhoeven
Hook up all devices that are part of the CPG/MSTP Clock Domain to the
SYSC "always-on" PM Domain, for a more consistent device-power-area
description in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v6:
- Rebased,
v5:
- Add Acked-by,
v4:
- New.
---
arch/arm/boot/dts/r8a7794.dtsi | 106 ++++++++++++++++++++---------------------
1 file changed, 53 insertions(+), 53 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 70eff80a813ec85a..136911c1dc74441c 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -86,7 +86,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7794_CLK_GPIO0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
};
gpio1: gpio@e6051000 {
@@ -99,7 +99,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7794_CLK_GPIO1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
};
gpio2: gpio@e6052000 {
@@ -112,7 +112,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7794_CLK_GPIO2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
};
gpio3: gpio@e6053000 {
@@ -125,7 +125,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7794_CLK_GPIO3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
};
gpio4: gpio@e6054000 {
@@ -138,7 +138,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7794_CLK_GPIO4>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
};
gpio5: gpio@e6055000 {
@@ -151,7 +151,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7794_CLK_GPIO5>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
};
gpio6: gpio@e6055400 {
@@ -164,7 +164,7 @@
#interrupt-cells = <2>;
interrupt-controller;
clocks = <&mstp9_clks R8A7794_CLK_GPIO6>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
};
cmt0: timer@ffca0000 {
@@ -174,7 +174,7 @@
<GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp1_clks R8A7794_CLK_CMT0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
renesas,channels-mask = <0x60>;
@@ -194,7 +194,7 @@
<GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7794_CLK_CMT1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
renesas,channels-mask = <0xff>;
@@ -225,7 +225,7 @@
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp4_clks R8A7794_CLK_IRQC>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
};
pfc: pin-controller@e6060000 {
@@ -259,7 +259,7 @@
"ch12", "ch13", "ch14";
clocks = <&mstp2_clks R8A7794_CLK_SYS_DMAC0>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <15>;
};
@@ -290,7 +290,7 @@
"ch12", "ch13", "ch14";
clocks = <&mstp2_clks R8A7794_CLK_SYS_DMAC1>;
clock-names = "fck";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#dma-cells = <1>;
dma-channels = <15>;
};
@@ -304,7 +304,7 @@
clock-names = "fck";
dmas = <&dmac0 0x21>, <&dmac0 0x22>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -317,7 +317,7 @@
clock-names = "fck";
dmas = <&dmac0 0x25>, <&dmac0 0x26>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -330,7 +330,7 @@
clock-names = "fck";
dmas = <&dmac0 0x27>, <&dmac0 0x28>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -343,7 +343,7 @@
clock-names = "fck";
dmas = <&dmac0 0x1b>, <&dmac0 0x1c>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -356,7 +356,7 @@
clock-names = "fck";
dmas = <&dmac0 0x1f>, <&dmac0 0x20>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -369,7 +369,7 @@
clock-names = "fck";
dmas = <&dmac0 0x23>, <&dmac0 0x24>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -382,7 +382,7 @@
clock-names = "fck";
dmas = <&dmac0 0x3d>, <&dmac0 0x3e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -395,7 +395,7 @@
clock-names = "fck";
dmas = <&dmac0 0x19>, <&dmac0 0x1a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -408,7 +408,7 @@
clock-names = "fck";
dmas = <&dmac0 0x1d>, <&dmac0 0x1e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -422,7 +422,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x29>, <&dmac0 0x2a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -436,7 +436,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2d>, <&dmac0 0x2e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -450,7 +450,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2b>, <&dmac0 0x2c>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -464,7 +464,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x2f>, <&dmac0 0x30>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -478,7 +478,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0xfb>, <&dmac0 0xfc>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -492,7 +492,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0xfd>, <&dmac0 0xfe>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -506,7 +506,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x39>, <&dmac0 0x3a>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -520,7 +520,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x4d>, <&dmac0 0x4e>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -534,7 +534,7 @@
clock-names = "fck", "brg_int", "scif_clk";
dmas = <&dmac0 0x3b>, <&dmac0 0x3c>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -543,7 +543,7 @@
reg = <0 0xee700000 0 0x400>;
interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7794_CLK_ETHER>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
phy-mode = "rmii";
#address-cells = <1>;
#size-cells = <0>;
@@ -556,7 +556,7 @@
reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7794_CLK_ETHERAVB>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -568,7 +568,7 @@
reg = <0 0xe6508000 0 0x40>;
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7794_CLK_I2C0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
i2c-scl-internal-delay-ns = <6>;
@@ -580,7 +580,7 @@
reg = <0 0xe6518000 0 0x40>;
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7794_CLK_I2C1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
i2c-scl-internal-delay-ns = <6>;
@@ -592,7 +592,7 @@
reg = <0 0xe6530000 0 0x40>;
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7794_CLK_I2C2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
i2c-scl-internal-delay-ns = <6>;
@@ -604,7 +604,7 @@
reg = <0 0xe6540000 0 0x40>;
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7794_CLK_I2C3>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
i2c-scl-internal-delay-ns = <6>;
@@ -616,7 +616,7 @@
reg = <0 0xe6520000 0 0x40>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7794_CLK_I2C4>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
i2c-scl-internal-delay-ns = <6>;
@@ -628,7 +628,7 @@
reg = <0 0xe6528000 0 0x40>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp9_clks R8A7794_CLK_I2C5>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
i2c-scl-internal-delay-ns = <6>;
@@ -642,7 +642,7 @@
clocks = <&mstp3_clks R8A7794_CLK_IIC0>;
dmas = <&dmac0 0x61>, <&dmac0 0x62>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -655,7 +655,7 @@
clocks = <&mstp3_clks R8A7794_CLK_IIC1>;
dmas = <&dmac0 0x65>, <&dmac0 0x66>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
@@ -668,7 +668,7 @@
clocks = <&mstp3_clks R8A7794_CLK_MMCIF0>;
dmas = <&dmac0 0xd1>, <&dmac0 0xd2>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
reg-io-width = <4>;
status = "disabled";
};
@@ -678,7 +678,7 @@
reg = <0 0xee100000 0 0x200>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7794_CLK_SDHI0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -687,7 +687,7 @@
reg = <0 0xee140000 0 0x100>;
interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7794_CLK_SDHI1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -696,7 +696,7 @@
reg = <0 0xee160000 0 0x100>;
interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp3_clks R8A7794_CLK_SDHI2>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -707,7 +707,7 @@
clocks = <&mstp9_clks R8A7794_CLK_QSPI_MOD>;
dmas = <&dmac0 0x17>, <&dmac0 0x18>;
dma-names = "tx", "rx";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
num-cs = <1>;
#address-cells = <1>;
#size-cells = <0>;
@@ -719,7 +719,7 @@
reg = <0 0xe6ef0000 0 0x1000>;
interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7794_CLK_VIN0>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -728,7 +728,7 @@
reg = <0 0xe6ef1000 0 0x1000>;
interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp8_clks R8A7794_CLK_VIN1>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -739,7 +739,7 @@
<0 0xee080000 0 0x1100>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7794_CLK_EHCI>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
bus-range = <0 0>;
@@ -774,7 +774,7 @@
<0 0xee0c0000 0 0x1100>;
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7794_CLK_EHCI>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
bus-range = <1 1>;
@@ -807,7 +807,7 @@
reg = <0 0xe6590000 0 0x100>;
interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp7_clks R8A7794_CLK_HSUSB>;
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
renesas,buswait = <4>;
phys = <&usb0 1>;
phy-names = "usb";
@@ -821,7 +821,7 @@
#size-cells = <0>;
clocks = <&mstp7_clks R8A7794_CLK_HSUSB>;
clock-names = "usbhs";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
usb0: usb-channel@0 {
@@ -869,7 +869,7 @@
clocks = <&mstp9_clks R8A7794_CLK_RCAN0>,
<&cpg_clocks R8A7794_CLK_RCAN>, <&can_clk>;
clock-names = "clkp1", "clkp2", "can_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -880,7 +880,7 @@
clocks = <&mstp9_clks R8A7794_CLK_RCAN1>,
<&cpg_clocks R8A7794_CLK_RCAN>, <&can_clk>;
clock-names = "clkp1", "clkp2", "can_clk";
- power-domains = <&cpg_clocks>;
+ power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
--
1.9.1
^ permalink raw reply related [flat|nested] 21+ messages in thread
* Re: [PATCH v6 00/12] ARM/arm64: dts: rcar: Add SYSC PM domains
2016-04-22 9:07 ` Geert Uytterhoeven
@ 2016-04-22 10:45 ` Simon Horman
-1 siblings, 0 replies; 21+ messages in thread
From: Simon Horman @ 2016-04-22 10:45 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Magnus Damm, Laurent Pinchart, linux-renesas-soc,
linux-arm-kernel, linux-pm, devicetree
On Fri, Apr 22, 2016 at 11:07:22AM +0200, Geert Uytterhoeven wrote:
> Hi Simon, Magnus,
>
> This patch series adds the R-Car System Controller to the DTS files for
> the various Renesas R-Car SoCs, and hooks up devices to their respective
> PM domains.
>
> This (more specifically patch 1) is a dependency for the enablement of the
> Display Unit on R-Car H3, as on this SoC the DU needs to use the VSPs, and the
> VSPs are located in a PM Domain.
>
> This series contains 2 parts, for both arm64 and arm32:
> 1. Patches 1 (arm64) and 3-7 (arm32) add device node for the System
> Controllers, and hook up CPU cores and L2 caches/SCUs to their
> respective PM Domains,
> 2. Patches 2 (arm64) and 8-12 (arm32) hook up devices to the SYSC
> "always-on" PM Domain, for a more consistent device-power-area
> description in DT.
>
> Changes compared to v5:
> - Add Acked-by,
> - Rebased R-Car Gen2 patches because of dropping of references to the
> second DMA controllers,
> - Updated for addition of sdhi[0-2] device nodes on r8a7793,
> - Reordered arm64 patches first, as these have a higher priority.
>
> Changes compared to v4:
> - Add Acked-by,
> - Remove "power-domains" property again from the sysc nodes, as the
> System Controller theirselves are not part of the Clock Domains.
>
> Changes compared to v3:
> - Add power-domains properties to the sysc nodes, to refer to the
> SoC's Clock Domains,
> - Extract using the SYSC "always-on" PM Domain on R-Car H3 into its
> own patch,
> - Add patches to use the SYSC "always-on" PM Domain on R-Car H1 and
> R-Car Gen2,
> - Update for recently added can0, can1, pciec0, and pciec1 device
> nodes on R-Car H3.
>
> Changes compared to v2:
> - Move power area hierarchy from DT to C (cfr. DT bindings for Renesas
> CPG/MSSR), and switch to "#power-domain-cells = <1>",
> - Drop fallback compatibility strings, as the bindings are
> SoC-specific,
> - Add an "always-on" power area on R-Car H3.
>
> Changes compared to v1:
> - Add R-Car H3 (r8a7795) support,
> - Use "renesas,<type>-sysc" instead of "renesas,sysc-<type>",
> - Add fallback compatibility strings for R-Car Gen2 and Gen3.
>
> Dependencies:
> - renesas-devel-20160422v2-v4.6-rc4.
>
> Suggested patch application strategy:
> - On branch arm64-dt-for-v4.7:
> - Merge rcar-sysc-for-v4.7,
> - Apply patches 1-2.
> - On branch dt-for-v4.7:
> - Merge rcar-sysc-for-v4.7,
> - Apply patches 3-12.
>
> Suggested arm-soc pull request strategy:
> - Send pull-request for rcar-sysc-for-v4.7,
> - Send pull-request for arm64-dt-for-v4.7,
> - Send pull-request for dt-for-v4.7.
>
> For your convenience, I've pushed this to the topic/rcar-sysc-pd-dt-v6
> branch of
> git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git.
> Integration with renesas-drivers-2016-04-12-v4.6-rc3 is available in the
> topic/gen3-latest branch.
>
> This has been tested on r8a7779/marzen, r8a7790/lager, r8a7791/koelsch,
> r8a7794/alt, and r8a7795/salvator-x.
>
> Thanks for applying!
Thanks, done.
^ permalink raw reply [flat|nested] 21+ messages in thread
* [PATCH v6 00/12] ARM/arm64: dts: rcar: Add SYSC PM domains
@ 2016-04-22 10:45 ` Simon Horman
0 siblings, 0 replies; 21+ messages in thread
From: Simon Horman @ 2016-04-22 10:45 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Apr 22, 2016 at 11:07:22AM +0200, Geert Uytterhoeven wrote:
> Hi Simon, Magnus,
>
> This patch series adds the R-Car System Controller to the DTS files for
> the various Renesas R-Car SoCs, and hooks up devices to their respective
> PM domains.
>
> This (more specifically patch 1) is a dependency for the enablement of the
> Display Unit on R-Car H3, as on this SoC the DU needs to use the VSPs, and the
> VSPs are located in a PM Domain.
>
> This series contains 2 parts, for both arm64 and arm32:
> 1. Patches 1 (arm64) and 3-7 (arm32) add device node for the System
> Controllers, and hook up CPU cores and L2 caches/SCUs to their
> respective PM Domains,
> 2. Patches 2 (arm64) and 8-12 (arm32) hook up devices to the SYSC
> "always-on" PM Domain, for a more consistent device-power-area
> description in DT.
>
> Changes compared to v5:
> - Add Acked-by,
> - Rebased R-Car Gen2 patches because of dropping of references to the
> second DMA controllers,
> - Updated for addition of sdhi[0-2] device nodes on r8a7793,
> - Reordered arm64 patches first, as these have a higher priority.
>
> Changes compared to v4:
> - Add Acked-by,
> - Remove "power-domains" property again from the sysc nodes, as the
> System Controller theirselves are not part of the Clock Domains.
>
> Changes compared to v3:
> - Add power-domains properties to the sysc nodes, to refer to the
> SoC's Clock Domains,
> - Extract using the SYSC "always-on" PM Domain on R-Car H3 into its
> own patch,
> - Add patches to use the SYSC "always-on" PM Domain on R-Car H1 and
> R-Car Gen2,
> - Update for recently added can0, can1, pciec0, and pciec1 device
> nodes on R-Car H3.
>
> Changes compared to v2:
> - Move power area hierarchy from DT to C (cfr. DT bindings for Renesas
> CPG/MSSR), and switch to "#power-domain-cells = <1>",
> - Drop fallback compatibility strings, as the bindings are
> SoC-specific,
> - Add an "always-on" power area on R-Car H3.
>
> Changes compared to v1:
> - Add R-Car H3 (r8a7795) support,
> - Use "renesas,<type>-sysc" instead of "renesas,sysc-<type>",
> - Add fallback compatibility strings for R-Car Gen2 and Gen3.
>
> Dependencies:
> - renesas-devel-20160422v2-v4.6-rc4.
>
> Suggested patch application strategy:
> - On branch arm64-dt-for-v4.7:
> - Merge rcar-sysc-for-v4.7,
> - Apply patches 1-2.
> - On branch dt-for-v4.7:
> - Merge rcar-sysc-for-v4.7,
> - Apply patches 3-12.
>
> Suggested arm-soc pull request strategy:
> - Send pull-request for rcar-sysc-for-v4.7,
> - Send pull-request for arm64-dt-for-v4.7,
> - Send pull-request for dt-for-v4.7.
>
> For your convenience, I've pushed this to the topic/rcar-sysc-pd-dt-v6
> branch of
> git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git.
> Integration with renesas-drivers-2016-04-12-v4.6-rc3 is available in the
> topic/gen3-latest branch.
>
> This has been tested on r8a7779/marzen, r8a7790/lager, r8a7791/koelsch,
> r8a7794/alt, and r8a7795/salvator-x.
>
> Thanks for applying!
Thanks, done.
^ permalink raw reply [flat|nested] 21+ messages in thread
end of thread, other threads:[~2016-04-22 10:45 UTC | newest]
Thread overview: 21+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-04-22 9:07 [PATCH v6 00/12] ARM/arm64: dts: rcar: Add SYSC PM domains Geert Uytterhoeven
2016-04-22 9:07 ` Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 01/12] arm64: dts: r8a7795: Add SYSC PM Domains Geert Uytterhoeven
2016-04-22 9:07 ` Geert Uytterhoeven
2016-04-22 9:07 ` Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 02/12] arm64: dts: r8a7795: Use SYSC "always-on" PM Domain Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 03/12] ARM: dts: r8a7779: Add SYSC PM Domains Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 04/12] ARM: dts: r8a7790: " Geert Uytterhoeven
[not found] ` <1461316054-27999-1-git-send-email-geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
2016-04-22 9:07 ` [PATCH v6 05/12] ARM: dts: r8a7791: " Geert Uytterhoeven
2016-04-22 9:07 ` Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 06/12] ARM: dts: r8a7793: " Geert Uytterhoeven
2016-04-22 9:07 ` Geert Uytterhoeven
2016-04-22 9:07 ` Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 07/12] ARM: dts: r8a7794: " Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 08/12] ARM: dts: r8a7779: Use SYSC "always-on" PM Domain Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 09/12] ARM: dts: r8a7790: " Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 10/12] ARM: dts: r8a7791: " Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 11/12] ARM: dts: r8a7793: " Geert Uytterhoeven
2016-04-22 9:07 ` [PATCH v6 12/12] ARM: dts: r8a7794: " Geert Uytterhoeven
2016-04-22 10:45 ` [PATCH v6 00/12] ARM/arm64: dts: rcar: Add SYSC PM domains Simon Horman
2016-04-22 10:45 ` Simon Horman
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.