[U-Boot] [PATCH v6 00/10] armv8: ls2080aqds: Enable QSPI boot support

[U-Boot] [PATCH v6 00/10] armv8: ls2080aqds: Enable QSPI boot support

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

This patch adds QSPI boot support for LS2080AQDS board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then we can switch to booting from QSPI memory space.

Yuan Yao (10):
  drivers: i2c: mxc: Add early init
  armv8: ls2080aqds: Select QSPI CLK div via SCFG
  configs: ls2080a_common: Remove duplicate NOR configs
  armv8: ls2080aqds: disable IFC NOR & QIXIS when QSPI enable
  configs: ls2080aqds: Enable QSPI flash support
	Changed in v6.
  dm: dts: ls2080aqds: Add QSPI dts node
  armv8: ls2080aqds: Config QSPI pin mux via FPGA in NAND boot
  configs: ls2080a: Increase load image len in NAND boot
  ls2080aqds_nand_defconfig: Enable QSPI & its dependence
	Changed in v6.
  armv8: ls2080aqds: Enable QSPI boot support
	Changed in v6.

 arch/arm/dts/fsl-ls2080a-qds.dts                   | 14 +++++++
 arch/arm/dts/fsl-ls2080a.dtsi                      | 10 +++++
 arch/arm/include/asm/arch-fsl-layerscape/cpu.h     |  4 ++
 .../include/asm/arch-fsl-layerscape/immap_lsch3.h  |  3 ++
 board/freescale/ls2080aqds/ls2080aqds.c            | 19 ++++++++++
 configs/ls2080aqds_nand_defconfig                  |  8 ++++
 configs/ls2080aqds_qspi_defconfig                  | 27 ++++++++++++++
 drivers/i2c/i2c_core.c                             |  5 +++
 drivers/i2c/mxc_i2c.c                              | 27 ++++++++++++++
 include/configs/ls2080a_common.h                   | 11 ++----
 include/configs/ls2080a_simu.h                     |  7 ++++
 include/configs/ls2080aqds.h                       | 43 +++++++++++++++++++++-
 include/i2c.h                                      |  3 ++
 13 files changed, 171 insertions(+), 10 deletions(-)
 create mode 100644 configs/ls2080aqds_qspi_defconfig

-- 
2.1.0.27.g96db324

[U-Boot] [PATCH v6 01/10] drivers: i2c: mxc: Add early init

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

Add early i2c init function with conservative divider when the exact
clock rate is not available.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
---
New add in v3.
---
 drivers/i2c/i2c_core.c |  5 +++++
 drivers/i2c/mxc_i2c.c  | 27 +++++++++++++++++++++++++++
 include/i2c.h          |  3 +++
 3 files changed, 35 insertions(+)

diff --git a/drivers/i2c/i2c_core.c b/drivers/i2c/i2c_core.c
index 41cc3b8..16b1aba 100644
--- a/drivers/i2c/i2c_core.c
+++ b/drivers/i2c/i2c_core.c
@@ -233,6 +233,11 @@ __weak void i2c_init_board(void)
 {
 }
 
+/* implement possible for i2c specific early i2c init */
+__weak void i2c_early_init_f(void)
+{
+}
+
 /*
  * i2c_init_all():
  *
diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c
index 445fa21..f340208 100644
--- a/drivers/i2c/mxc_i2c.c
+++ b/drivers/i2c/mxc_i2c.c
@@ -32,6 +32,14 @@ DECLARE_GLOBAL_DATA_PTR;
 
 #define IMX_I2C_REGSHIFT	2
 #define VF610_I2C_REGSHIFT	0
+
+#define I2C_EARLY_INIT_INDEX		0
+#ifdef CONFIG_SYS_I2C_IFDR_DIV
+#define I2C_IFDR_DIV_CONSERVATIVE	CONFIG_SYS_I2C_IFDR_DIV
+#else
+#define I2C_IFDR_DIV_CONSERVATIVE	0x7e
+#endif
+
 /* Register index */
 #define IADR	0
 #define IFDR	1
@@ -660,6 +668,25 @@ void bus_i2c_init(int index, int speed, int unused,
 }
 
 /*
+ * Early init I2C for prepare read the clk through I2C.
+ */
+void i2c_early_init_f(void)
+{
+	ulong base = mxc_i2c_buses[I2C_EARLY_INIT_INDEX].base;
+	bool quirk = mxc_i2c_buses[I2C_EARLY_INIT_INDEX].driver_data
+					& I2C_QUIRK_FLAG ? true : false;
+	int reg_shift = quirk ? VF610_I2C_REGSHIFT : IMX_I2C_REGSHIFT;
+
+	/* Set I2C divider value */
+	writeb(I2C_IFDR_DIV_CONSERVATIVE, base + (IFDR << reg_shift));
+	/* Reset module */
+	writeb(I2CR_IDIS, base + (I2CR << reg_shift));
+	writeb(0, base + (I2SR << reg_shift));
+	/* Enable I2C */
+	writeb(I2CR_IEN, base + (I2CR << reg_shift));
+}
+
+/*
  * Init I2C Bus
  */
 static void mxc_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
diff --git a/include/i2c.h b/include/i2c.h
index 1f5ae45..d500445 100644
--- a/include/i2c.h
+++ b/include/i2c.h
@@ -701,6 +701,9 @@ extern struct i2c_bus_hose	i2c_bus[];
  * Initialization, must be called once on start up, may be called
  * repeatedly to change the speed and slave addresses.
  */
+#ifdef CONFIG_SYS_I2C_EARLY_INIT
+void i2c_early_init_f(void);
+#endif
 void i2c_init(int speed, int slaveaddr);
 void i2c_init_board(void);
 #ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
-- 
2.1.0.27.g96db324

[U-Boot] [PATCH v6 01/10] drivers: i2c: mxc: Add early init

[York Sun]

On 06/08/2016 03:35 AM, Yuan Yao wrote:
> From: Yuan Yao <yao.yuan@nxp.com>
> 
> Add early i2c init function with conservative divider when the exact
> clock rate is not available.
> 
> Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
> ---

With minor change to commit message, v6 patch set has been applied to fsl-qoriq
master. Awaiting upstream. Thanks.

York

[U-Boot] [PATCH v6 02/10] armv8: ls2080aqds: Select QSPI CLK div via SCFG

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

QSPI module output SCLK divisor value is configured through SCFG.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
---
 arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h | 1 +
 board/freescale/ls2080aqds/ls2080aqds.c                | 5 +++++
 2 files changed, 6 insertions(+)

diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
index 65b3357..bfff2ec 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
@@ -139,6 +139,7 @@
 /* Supplemental Configuration */
 #define SCFG_BASE		0x01fc0000
 #define SCFG_USB3PRM1CR			0x000
+#define SCFG_QSPICLKCTLR	0x10
 
 #define TP_ITYP_AV		0x00000001	/* Initiator available */
 #define TP_ITYP_TYPE(x)	(((x) & 0x6) >> 1)	/* Initiator Type */
diff --git a/board/freescale/ls2080aqds/ls2080aqds.c b/board/freescale/ls2080aqds/ls2080aqds.c
index b3bd40a..d7acb48 100644
--- a/board/freescale/ls2080aqds/ls2080aqds.c
+++ b/board/freescale/ls2080aqds/ls2080aqds.c
@@ -26,6 +26,7 @@
 
 #define PIN_MUX_SEL_SDHC	0x00
 #define PIN_MUX_SEL_DSPI	0x0a
+#define SCFG_QSPICLKCTRL_DIV_20	(5 << 27)
 
 #define SET_SDHC_MUX_SEL(reg, value)	((reg & 0xf0) | value)
 
@@ -219,6 +220,10 @@ int board_init(void)
 int board_early_init_f(void)
 {
 	fsl_lsch3_early_init_f();
+#ifdef CONFIG_FSL_QSPI
+	/* input clk: 1/2 platform clk, output: input/20 */
+	out_le32(SCFG_BASE + SCFG_QSPICLKCTLR, SCFG_QSPICLKCTRL_DIV_20);
+#endif
 	return 0;
 }
 
-- 
2.1.0.27.g96db324

[U-Boot] [PATCH v6 03/10] configs: ls2080a_common: Remove duplicate NOR configs

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

The NOR flash related configure options also appear in ls2080aqds.h and
ls2080ardb.h, and the two files all have included ls2080a_common.h.
This patch remove the duplicated options in ls2080a_common.h.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
---
 include/configs/ls2080a_common.h | 7 -------
 include/configs/ls2080a_simu.h   | 7 +++++++
 2 files changed, 7 insertions(+), 7 deletions(-)

diff --git a/include/configs/ls2080a_common.h b/include/configs/ls2080a_common.h
index c78aeb5..48b1e15 100644
--- a/include/configs/ls2080a_common.h
+++ b/include/configs/ls2080a_common.h
@@ -138,13 +138,6 @@
 #define CONFIG_SYS_FLASH1_BASE_PHYS		0xC0000000
 #define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY	0x8000000
 
-#ifndef CONFIG_SYS_NO_FLASH
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#endif
-
 #ifndef __ASSEMBLY__
 unsigned long long get_qixis_addr(void);
 #endif
diff --git a/include/configs/ls2080a_simu.h b/include/configs/ls2080a_simu.h
index 7563aaf..7f245b5 100644
--- a/include/configs/ls2080a_simu.h
+++ b/include/configs/ls2080a_simu.h
@@ -30,6 +30,13 @@
 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
 #define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
 
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#endif
+
 /*
  * NOR Flash Timing Params
  */
-- 
2.1.0.27.g96db324

[U-Boot] [PATCH v6 04/10] armv8: ls2080aqds: disable IFC NOR & QIXIS when QSPI enable

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

When QSPI is enabled, NOR flash and QIXIS can't be accessed
through IFC due to pin mux.
So enable I2C QIXIS access and I2C early init to read the
sysclk and ddrclk.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
---
Changed in v5:
	Use I2C to read the clocks instead of the hard-coded clocks. 
---
 board/freescale/ls2080aqds/ls2080aqds.c |  3 +++
 include/configs/ls2080aqds.h            | 10 ++++++++++
 2 files changed, 13 insertions(+)

diff --git a/board/freescale/ls2080aqds/ls2080aqds.c b/board/freescale/ls2080aqds/ls2080aqds.c
index d7acb48..19bb4c6 100644
--- a/board/freescale/ls2080aqds/ls2080aqds.c
+++ b/board/freescale/ls2080aqds/ls2080aqds.c
@@ -219,6 +219,9 @@ int board_init(void)
 
 int board_early_init_f(void)
 {
+#ifdef CONFIG_SYS_I2C_EARLY_INIT
+	i2c_early_init_f();
+#endif
 	fsl_lsch3_early_init_f();
 #ifdef CONFIG_FSL_QSPI
 	/* input clk: 1/2 platform clk, output: input/20 */
diff --git a/include/configs/ls2080aqds.h b/include/configs/ls2080aqds.h
index 4b27114..ccc987c 100644
--- a/include/configs/ls2080aqds.h
+++ b/include/configs/ls2080aqds.h
@@ -17,6 +17,16 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 #define CONFIG_SYS_FSL_CLK
+
+#ifdef CONFIG_FSL_QSPI
+#define CONFIG_SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
+#define CONFIG_QIXIS_I2C_ACCESS
+#define CONFIG_SYS_I2C_EARLY_INIT
+#define CONFIG_SYS_I2C_IFDR_DIV		0x7e
+#endif
+
+#define CONFIG_SYS_I2C_FPGA_ADDR	0x66
 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
 #define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ/4)
-- 
2.1.0.27.g96db324

[U-Boot] [PATCH v6 05/10] configs: ls2080aqds: Enable QSPI flash support

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

Enable QSPI flash related configure options.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
---
Changed in v6:
	remove CONFIG_CMD_SF.
---
 include/configs/ls2080aqds.h | 15 ++++++++++++++-
 1 file changed, 14 insertions(+), 1 deletion(-)

diff --git a/include/configs/ls2080aqds.h b/include/configs/ls2080aqds.h
index ccc987c..8e193a6 100644
--- a/include/configs/ls2080aqds.h
+++ b/include/configs/ls2080aqds.h
@@ -289,8 +289,21 @@ unsigned long get_board_ddr_clk(void);
 #define I2C_MUX_CH_DEFAULT      0x8
 
 /* SPI */
-#ifdef CONFIG_FSL_DSPI
+#if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI)
 #define CONFIG_SPI_FLASH
+
+#ifdef CONFIG_FSL_DSPI
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_EON
+#endif
+
+#ifdef CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE		(1 << 26) /* 64MB */
+#define FSL_QSPI_FLASH_NUM		4
+#endif
+
 #endif
 
 /*
-- 
2.1.0.27.g96db324

[U-Boot] [PATCH v6 06/10] dm: dts: ls2080aqds: Add QSPI dts node

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

Add QSPI controller and slave dts node for LS2080AQDS board.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
---
 arch/arm/dts/fsl-ls2080a-qds.dts | 14 ++++++++++++++
 arch/arm/dts/fsl-ls2080a.dtsi    | 10 ++++++++++
 2 files changed, 24 insertions(+)

diff --git a/arch/arm/dts/fsl-ls2080a-qds.dts b/arch/arm/dts/fsl-ls2080a-qds.dts
index 547ec27..0a7f1ff 100644
--- a/arch/arm/dts/fsl-ls2080a-qds.dts
+++ b/arch/arm/dts/fsl-ls2080a-qds.dts
@@ -15,6 +15,7 @@
 	compatible = "fsl,ls2080a-qds", "fsl,ls2080a";
 
 	aliases {
+		spi0 = &qspi;
 		spi1 = &dspi;
 	};
 };
@@ -51,3 +52,16 @@
 		reg = <2>;
 	};
 };
+
+&qspi {
+	bus-num = <0>;
+	status = "okay";
+
+	qflash0: s25fs256s at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
diff --git a/arch/arm/dts/fsl-ls2080a.dtsi b/arch/arm/dts/fsl-ls2080a.dtsi
index a5c579c..68ed133 100644
--- a/arch/arm/dts/fsl-ls2080a.dtsi
+++ b/arch/arm/dts/fsl-ls2080a.dtsi
@@ -126,4 +126,14 @@
 		interrupts = <0 26 0x4>; /* Level high type */
 		num-cs = <6>;
 	};
+
+	qspi: quadspi at 1550000 {
+		compatible = "fsl,vf610-qspi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0x20c0000 0x0 0x10000>,
+			<0x0 0x20000000 0x0 0x10000000>;
+		reg-names = "QuadSPI", "QuadSPI-memory";
+		num-cs = <4>;
+	};
 };
-- 
2.1.0.27.g96db324

[U-Boot] [PATCH v6 07/10] armv8: ls2080aqds: Config QSPI pin mux via FPGA in NAND boot

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

In order to access QSPI flash we must asserted ISO allowing
the DUT to access the full IFC domain.
But deasserted the unused ISO will allowing maximum performance.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
---
 arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h | 2 ++
 board/freescale/ls2080aqds/ls2080aqds.c                | 9 +++++++++
 include/configs/ls2080aqds.h                           | 6 ++++++
 3 files changed, 17 insertions(+)

diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
index bfff2ec..7c47cc8 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
@@ -128,6 +128,8 @@
 #define DCFG_PORSR1_RCW_SRC_NOR		0x12f00000
 #define DCFG_RCWSR13			0x130
 #define DCFG_RCWSR13_DSPI		(0 << 8)
+#define DCFG_RCWSR15			0x138
+#define DCFG_RCWSR15_IFCGRPABASE_QSPI	0x3
 
 #define DCFG_DCSR_BASE		0X700100000ULL
 #define DCFG_DCSR_PORCR1		0x000
diff --git a/board/freescale/ls2080aqds/ls2080aqds.c b/board/freescale/ls2080aqds/ls2080aqds.c
index 19bb4c6..8bdcb04 100644
--- a/board/freescale/ls2080aqds/ls2080aqds.c
+++ b/board/freescale/ls2080aqds/ls2080aqds.c
@@ -208,6 +208,15 @@ int board_init(void)
 	else
 		config_board_mux(MUX_TYPE_SDHC);
 
+#if defined(CONFIG_NAND) && defined(CONFIG_FSL_QSPI)
+	val = in_le32(dcfg_ccsr + DCFG_RCWSR15 / 4);
+
+	if (DCFG_RCWSR15_IFCGRPABASE_QSPI == (val & (u32)0x3))
+		QIXIS_WRITE(brdcfg[9],
+			    (QIXIS_READ(brdcfg[9]) & 0xf8) |
+			     FSL_QIXIS_BRDCFG9_QSPI);
+#endif
+
 #ifdef CONFIG_ENV_IS_NOWHERE
 	gd->env_addr = (ulong)&default_environment[0];
 #endif
diff --git a/include/configs/ls2080aqds.h b/include/configs/ls2080aqds.h
index 8e193a6..7152c2b 100644
--- a/include/configs/ls2080aqds.h
+++ b/include/configs/ls2080aqds.h
@@ -303,6 +303,12 @@ unsigned long get_board_ddr_clk(void);
 #define FSL_QSPI_FLASH_SIZE		(1 << 26) /* 64MB */
 #define FSL_QSPI_FLASH_NUM		4
 #endif
+/*
+ * Verify QSPI when boot from NAND, QIXIS brdcfg9 need configure.
+ * If boot from on-board NAND, ISO1 = 1, ISO2 = 0, IBOOT = 0
+ * If boot from IFCCard NAND, ISO1 = 0, ISO2 = 0, IBOOT = 1
+ */
+#define FSL_QIXIS_BRDCFG9_QSPI		0x1
 
 #endif
 
-- 
2.1.0.27.g96db324

[U-Boot] [PATCH v6 08/10] configs: ls2080a: Increase load image len in NAND boot

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

Freescale QSPI and DSPI driver have been converted to Driver Mode.
This converting bring dtb file for u-boot and this increase the size
of u-boot image.
LS2080A nand boot use SPL framework.
This patch increase the size of image load from NAND to RAM in SPL.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
---
 include/configs/ls2080a_common.h | 2 +-
 include/configs/ls2080aqds.h     | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/include/configs/ls2080a_common.h b/include/configs/ls2080a_common.h
index 48b1e15..eab410e 100644
--- a/include/configs/ls2080a_common.h
+++ b/include/configs/ls2080a_common.h
@@ -283,7 +283,7 @@ unsigned long long get_qixis_addr(void);
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x00100000
 #define CONFIG_SYS_SPL_MALLOC_START	0x80200000
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(640 * 1024)
 
 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
diff --git a/include/configs/ls2080aqds.h b/include/configs/ls2080aqds.h
index 7152c2b..55d6c27 100644
--- a/include/configs/ls2080aqds.h
+++ b/include/configs/ls2080aqds.h
@@ -237,7 +237,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_ENV_SIZE			0x2000
 #define CONFIG_SPL_PAD_TO		0x20000
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 * 1024)
-#define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 * 1024)
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(640 * 1024)
 #else
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
-- 
2.1.0.27.g96db324

[U-Boot] [PATCH v6 09/10] ls2080aqds_nand_defconfig: Enable QSPI & its dependence

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

The Freescale QSPI driver has been converted to Driver Model.
This patch enable FSL_QSPI and its dependence options, DM, DM_SPI,
OF_CONTROL and so on.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
---
Changed in v6:
	Add CONFIG_CMD_SF in defconfig.
---
 configs/ls2080aqds_nand_defconfig | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/configs/ls2080aqds_nand_defconfig b/configs/ls2080aqds_nand_defconfig
index 1302313..d567878 100644
--- a/configs/ls2080aqds_nand_defconfig
+++ b/configs/ls2080aqds_nand_defconfig
@@ -6,6 +6,14 @@ CONFIG_FIT_VERBOSE=y
 CONFIG_OF_BOARD_SETUP=y
 CONFIG_OF_STDOUT_VIA_ALIAS=y
 CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4, NAND, LS2080A"
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds"
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_DISABLE_OF_CONTROL=y
+CONFIG_OF_EMBED=y
+CONFIG_DM=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_GREPENV=y
 CONFIG_CMD_MMC=y
@@ -18,6 +26,7 @@ CONFIG_CMD_PING=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_FAT=y
+CONFIG_CMD_SF=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_NETDEVICES=y
 CONFIG_E1000=y
-- 
2.1.0.27.g96db324

[U-Boot] [PATCH v6 10/10] armv8: ls2080aqds: Enable QSPI boot support

[Yuan Yao]

From: Yuan Yao <yao.yuan@nxp.com>

This patch adds QSPI boot support for LS2080AQDS board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then we can switch to booting from QSPI memory space.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
---
Changed in v6:
	Add CONFIG_CMD_SF in defconfig.
Changed in v4:
	Merged the below patch into one:
	board: freescale: ls2080aqds: Enable early I2C access for QSPI boot
Changed in v3:
	1, Rebase to lastest code.
	2, Give up to change the sequence for "show_board_info" in "init_sequence_f".
---
 arch/arm/include/asm/arch-fsl-layerscape/cpu.h |  4 ++++
 board/freescale/ls2080aqds/ls2080aqds.c        |  2 ++
 configs/ls2080aqds_qspi_defconfig              | 28 ++++++++++++++++++++++++++
 include/configs/ls2080a_common.h               |  2 ++
 include/configs/ls2080aqds.h                   | 10 +++++++++
 5 files changed, 46 insertions(+)
 create mode 100644 configs/ls2080aqds_qspi_defconfig

diff --git a/arch/arm/include/asm/arch-fsl-layerscape/cpu.h b/arch/arm/include/asm/arch-fsl-layerscape/cpu.h
index 702b9fa..f07a49a 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/cpu.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/cpu.h
@@ -121,6 +121,8 @@ static const struct sys_mmu_table early_mmu_table[] = {
 	  PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN },
 	{ CONFIG_SYS_FSL_OCRAM_BASE, CONFIG_SYS_FSL_OCRAM_BASE,
 	  CONFIG_SYS_FSL_OCRAM_SIZE, MT_NORMAL, PTE_BLOCK_NON_SHARE },
+	{ CONFIG_SYS_FSL_QSPI_BASE1, CONFIG_SYS_FSL_QSPI_BASE1,
+	  CONFIG_SYS_FSL_QSPI_SIZE1,  MT_NORMAL, PTE_BLOCK_NON_SHARE},
 	/* For IFC Region #1, only the first 4MB is cache-enabled */
 	{ CONFIG_SYS_FSL_IFC_BASE1, CONFIG_SYS_FSL_IFC_BASE1,
 	  CONFIG_SYS_FSL_IFC_SIZE1_1, MT_NORMAL, PTE_BLOCK_NON_SHARE },
@@ -175,6 +177,8 @@ static const struct sys_mmu_table final_mmu_table[] = {
 	{ CONFIG_SYS_FSL_DRAM_BASE1, CONFIG_SYS_FSL_DRAM_BASE1,
 	  CONFIG_SYS_FSL_DRAM_SIZE1, MT_NORMAL,
 	  PTE_BLOCK_OUTER_SHARE | PTE_BLOCK_NS },
+	{ CONFIG_SYS_FSL_QSPI_BASE1, CONFIG_SYS_FSL_QSPI_BASE1,
+	  CONFIG_SYS_FSL_QSPI_SIZE1,  MT_NORMAL, PTE_BLOCK_NON_SHARE},
 	{ CONFIG_SYS_FSL_QSPI_BASE2, CONFIG_SYS_FSL_QSPI_BASE2,
 	  CONFIG_SYS_FSL_QSPI_SIZE2, MT_DEVICE_NGNRNE,
 	  PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN },
diff --git a/board/freescale/ls2080aqds/ls2080aqds.c b/board/freescale/ls2080aqds/ls2080aqds.c
index 8bdcb04..23ebcc1 100644
--- a/board/freescale/ls2080aqds/ls2080aqds.c
+++ b/board/freescale/ls2080aqds/ls2080aqds.c
@@ -81,6 +81,8 @@ int checkboard(void)
 		puts("PromJet\n");
 	else if (sw == 0x9)
 		puts("NAND\n");
+	else if (sw == 0xf)
+		puts("QSPI\n");
 	else if (sw == 0x15)
 		printf("IFCCard\n");
 	else
diff --git a/configs/ls2080aqds_qspi_defconfig b/configs/ls2080aqds_qspi_defconfig
new file mode 100644
index 0000000..194d280
--- /dev/null
+++ b/configs/ls2080aqds_qspi_defconfig
@@ -0,0 +1,28 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS2080AQDS=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds"
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,QSPI_BOOT,LS2080A"
+CONFIG_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_DM_SPI=y
+CONFIG_FSL_QSPI=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_SF=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_NETDEVICES=y
+CONFIG_E1000=y
+CONFIG_SYS_NS16550=y
diff --git a/include/configs/ls2080a_common.h b/include/configs/ls2080a_common.h
index eab410e..71f830a 100644
--- a/include/configs/ls2080a_common.h
+++ b/include/configs/ls2080a_common.h
@@ -29,11 +29,13 @@
 #define CONFIG_FSL_CAAM			/* Enable SEC/CAAM */
 
 /* Link Definitions */
+#ifndef CONFIG_QSPI_BOOT
 #ifdef CONFIG_SPL
 #define CONFIG_SYS_TEXT_BASE		0x80400000
 #else
 #define CONFIG_SYS_TEXT_BASE		0x30100000
 #endif
+#endif
 
 #ifdef CONFIG_EMU
 #define CONFIG_SYS_NO_FLASH
diff --git a/include/configs/ls2080aqds.h b/include/configs/ls2080aqds.h
index 55d6c27..5dfba7a 100644
--- a/include/configs/ls2080aqds.h
+++ b/include/configs/ls2080aqds.h
@@ -172,11 +172,13 @@ unsigned long get_board_ddr_clk(void);
 #define QIXIS_LBMAP_DFLTBANK		0x00
 #define QIXIS_LBMAP_ALTBANK		0x04
 #define QIXIS_LBMAP_NAND		0x09
+#define QIXIS_LBMAP_QSPI		0x0f
 #define QIXIS_RST_CTL_RESET		0x31
 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
 #define QIXIS_RCW_SRC_NAND		0x107
+#define QIXIS_RCW_SRC_QSPI		0x62
 #define	QIXIS_RST_FORCE_MEM		0x01
 
 #define CONFIG_SYS_CSPR3_EXT	(0x0)
@@ -267,11 +269,19 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
 
+#if defined(CONFIG_QSPI_BOOT)
+#define CONFIG_SYS_TEXT_BASE		0x20010000
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE			0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET		0x100000        /* 1MB */
+#define CONFIG_ENV_SECT_SIZE		0x10000
+#else
 #define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
 #define CONFIG_ENV_SECT_SIZE		0x20000
 #define CONFIG_ENV_SIZE			0x2000
 #endif
+#endif
 
 /* Debug Server firmware */
 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
-- 
2.1.0.27.g96db324