* [PATCH 0/5] arm64: dts: add QorIQ LS1046A SoC and boards support
@ 2016-07-08 10:15 ` shh.xie at gmail.com
0 siblings, 0 replies; 22+ messages in thread
From: shh.xie at gmail.com @ 2016-07-08 10:15 UTC (permalink / raw)
To: linux-arm-kernel
From: Shaohui Xie <Shaohui.Xie@nxp.com>
This patchest adds support for QorIQ LS1046A SoC which is based on ARMv8
architecture, also adds LS1046A-RDB and LS1046A-QDS board support.
Mingkai Hu (2):
arm64: dts: add QorIQ LS1046A SoC support
arm64: dts: add LS1046A-RDB board support
Shaohui Xie (3):
Documentation: DT: Add entry for QorIQ LS1046A-RDB board
Documentation: DT: Add entry for QorIQ LS1046A-QDS board
arm64: dts: add LS1046A-QDS board support
Documentation/devicetree/bindings/arm/fsl.txt | 8 +
arch/arm64/boot/dts/freescale/Makefile | 2 +
arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts | 209 ++++++++
arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts | 138 ++++++
arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 549 ++++++++++++++++++++++
5 files changed, 906 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
--
2.1.0.27.g96db324
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH 1/5] arm64: dts: add QorIQ LS1046A SoC support
2016-07-08 10:15 ` shh.xie at gmail.com
@ 2016-07-08 10:15 ` shh.xie at gmail.com
-1 siblings, 0 replies; 22+ messages in thread
From: shh.xie @ 2016-07-08 10:15 UTC (permalink / raw)
To: devicetree, robh+dt, mark.rutland, pawel.moll, ijc+devicetree,
galak, linux-arm-kernel, catalin.marinas, will.deacon
Cc: Mihai Bantea, Shaohui Xie, Hou Zhiqiang, Minghuan Lian,
Mingkai Hu, Gong Qianyu
From: Mingkai Hu <Mingkai.Hu@nxp.com>
LS1046A is an SoC with 4 ARMv8 A72 cores and most other IP blocks
are similar to LS1043A which also complies to Freescale Chassis 2.1
spec.
Created LS1046A SoC DTSI file to be included by board level DTS
files.
Signed-off-by: Mihai Bantea <mihai.bantea@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 549 +++++++++++++++++++++++++
1 file changed, 549 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
new file mode 100644
index 0000000..e28a686
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
@@ -0,0 +1,549 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor, Inc.
+ *
+ * Mingkai Hu <mingkai.hu@nxp.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+ compatible = "fsl,ls1046a";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x0>;
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x1>;
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x2>;
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x3>;
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0 0x80000000>;
+ /* DRAM space 1, size: 2GiB DRAM */
+ };
+
+ sysclk: sysclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "sysclk";
+ };
+
+ reboot {
+ compatible ="syscon-reboot";
+ regmap = <&dcfg>;
+ offset = <0xb0>;
+ mask = <0x02>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <1 13 0x1>, /* Physical Secure PPI */
+ <1 14 0x1>, /* Physical Non-Secure PPI */
+ <1 11 0x1>, /* Virtual PPI */
+ <1 10 0x1>; /* Hypervisor PPI */
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <0 106 0x4>,
+ <0 107 0x4>,
+ <0 95 0x4>,
+ <0 97 0x4>;
+ interrupt-affinity = <&cpu0>,
+ <&cpu1>,
+ <&cpu2>,
+ <&cpu3>;
+ };
+
+ gic: interrupt-controller@1400000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x0 0x1410000 0 0x10000>, /* GICD */
+ <0x0 0x1420000 0 0x20000>, /* GICC */
+ <0x0 0x1440000 0 0x20000>, /* GICH */
+ <0x0 0x1460000 0 0x20000>; /* GICV */
+ interrupts = <1 9 0xf08>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clockgen: clocking@1ee1000 {
+ compatible = "fsl,ls1046a-clockgen";
+ reg = <0x0 0x1ee1000 0x0 0x1000>;
+ #clock-cells = <2>;
+ clocks = <&sysclk>;
+ };
+
+ scfg: scfg@1570000 {
+ compatible = "fsl,ls1046a-scfg", "syscon";
+ reg = <0x0 0x1570000 0x0 0x10000>;
+ big-endian;
+ };
+
+ dcfg: dcfg@1ee0000 {
+ compatible = "fsl,ls1046a-dcfg", "syscon";
+ reg = <0x0 0x1ee0000 0x0 0x10000>;
+ big-endian;
+ };
+
+ rcpm: rcpm@1ee2000 {
+ compatible = "fsl,ls1046a-rcpm", "fsl,qoriq-rcpm-2.1";
+ reg = <0x0 0x1ee2000 0x0 0x10000>;
+ };
+
+ ifc: ifc@1530000 {
+ compatible = "fsl,ifc", "simple-bus";
+ reg = <0x0 0x1530000 0x0 0x10000>;
+ interrupts = <0 43 0x4>;
+ };
+
+ esdhc: esdhc@1560000 {
+ compatible = "fsl,ls1046a-esdhc", "fsl,esdhc";
+ reg = <0x0 0x1560000 0x0 0x10000>;
+ interrupts = <0 62 0x4>;
+ clock-frequency = <0>;
+ voltage-ranges = <1800 1800 3300 3300>;
+ sdhci,auto-cmd12;
+ big-endian;
+ bus-width = <4>;
+ };
+
+ dspi: dspi@2100000 {
+ compatible = "fsl,ls1046a-dspi", "fsl,ls1021a-v1.0-dspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2100000 0x0 0x10000>;
+ interrupts = <0 64 0x4>;
+ clock-names = "dspi";
+ clocks = <&clockgen 4 1>;
+ spi-num-chipselects = <5>;
+ big-endian;
+ status = "disabled";
+ };
+
+ qspi: quadspi@1550000 {
+ compatible = "fsl,ls1046a-qspi", "fsl,ls1021a-qspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x1550000 0x0 0x10000>,
+ <0x0 0x40000000 0x0 0x10000000>;
+ reg-names = "QuadSPI", "QuadSPI-memory";
+ interrupts = <0 99 0x4>;
+ clock-names = "qspi_en", "qspi";
+ clocks = <&clockgen 4 1>, <&clockgen 4 1>;
+ big-endian;
+ fsl,qspi-has-second-chip;
+ status = "disabled";
+ };
+
+ i2c0: i2c@2180000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2180000 0x0 0x10000>;
+ interrupts = <0 56 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 1>;
+ dmas = <&edma0 1 39>,
+ <&edma0 1 38>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c1: i2c@2190000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2190000 0x0 0x10000>;
+ interrupts = <0 57 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@21a0000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x21a0000 0x0 0x10000>;
+ interrupts = <0 58 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@21b0000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x21b0000 0x0 0x10000>;
+ interrupts = <0 59 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ duart0: serial@21c0500 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x00 0x21c0500 0x0 0x100>;
+ interrupts = <0 54 0x4>;
+ clocks = <&clockgen 4 1>;
+ };
+
+ duart1: serial@21c0600 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x00 0x21c0600 0x0 0x100>;
+ interrupts = <0 54 0x4>;
+ clocks = <&clockgen 4 1>;
+ };
+
+ duart2: serial@21d0500 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x0 0x21d0500 0x0 0x100>;
+ interrupts = <0 55 0x4>;
+ clocks = <&clockgen 4 1>;
+ };
+
+ duart3: serial@21d0600 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x0 0x21d0600 0x0 0x100>;
+ interrupts = <0 55 0x4>;
+ clocks = <&clockgen 4 1>;
+ };
+
+ gpio0: gpio@2300000 {
+ compatible = "fsl,ls1046a-gpio";
+ reg = <0x0 0x2300000 0x0 0x10000>;
+ interrupts = <0 66 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@2310000 {
+ compatible = "fsl,ls1046a-gpio";
+ reg = <0x0 0x2310000 0x0 0x10000>;
+ interrupts = <0 67 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@2320000 {
+ compatible = "fsl,ls1046a-gpio";
+ reg = <0x0 0x2320000 0x0 0x10000>;
+ interrupts = <0 68 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@2330000 {
+ compatible = "fsl,ls1046a-gpio";
+ reg = <0x0 0x2330000 0x0 0x10000>;
+ interrupts = <0 134 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ lpuart0: serial@2950000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x2950000 0x0 0x1000>;
+ interrupts = <0 48 0x4>;
+ clocks = <&clockgen 0 0>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart1: serial@2960000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x2960000 0x0 0x1000>;
+ interrupts = <0 49 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart2: serial@2970000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x2970000 0x0 0x1000>;
+ interrupts = <0 50 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart3: serial@2980000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x2980000 0x0 0x1000>;
+ interrupts = <0 51 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart4: serial@2990000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x2990000 0x0 0x1000>;
+ interrupts = <0 52 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart5: serial@29a0000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x29a0000 0x0 0x1000>;
+ interrupts = <0 53 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ wdog0: wdog@2ad0000 {
+ compatible = "fsl,ls1046a-wdt", "fsl,imx21-wdt";
+ reg = <0x0 0x2ad0000 0x0 0x10000>;
+ interrupts = <0 83 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "wdog";
+ big-endian;
+ };
+
+ edma0: edma@2c00000 {
+ #dma-cells = <2>;
+ compatible = "fsl,vf610-edma";
+ reg = <0x0 0x2c00000 0x0 0x10000>,
+ <0x0 0x2c10000 0x0 0x10000>,
+ <0x0 0x2c20000 0x0 0x10000>;
+ interrupts = <0 103 0x4>,
+ <0 103 0x4>;
+ interrupt-names = "edma-tx", "edma-err";
+ dma-channels = <32>;
+ big-endian;
+ clock-names = "dmamux0", "dmamux1";
+ clocks = <&clockgen 4 1>,
+ <&clockgen 4 1>;
+ };
+
+ usb0: usb3@2f00000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0x2f00000 0x0 0x10000>;
+ interrupts = <0 60 0x4>;
+ dr_mode = "host";
+ snps,quirk-frame-length-adjustment = <0x20>;
+ };
+
+ usb1: usb3@3000000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0x3000000 0x0 0x10000>;
+ interrupts = <0 61 0x4>;
+ dr_mode = "host";
+ snps,quirk-frame-length-adjustment = <0x20>;
+ };
+
+ usb2: usb3@3100000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0x3100000 0x0 0x10000>;
+ interrupts = <0 63 0x4>;
+ dr_mode = "host";
+ snps,quirk-frame-length-adjustment = <0x20>;
+ };
+
+ sata: sata@3200000 {
+ compatible = "fsl,ls1046a-ahci", "fsl,ls1021a-ahci";
+ reg = <0x0 0x3200000 0x0 0x10000>;
+ interrupts = <0 69 0x4>;
+ clocks = <&clockgen 4 1>;
+ };
+
+ msi: msi-controller@1580000 {
+ compatible = "fsl,ls1046a-msi";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ msi-controller;
+ msi-bank@1580000 {
+ reg = <0x0 0x1580000 0x0 0x10000>;
+ interrupts = <0 116 0x4>,
+ <0 111 0x4>,
+ <0 112 0x4>,
+ <0 113 0x4>;
+
+ };
+
+ msi-bank@1590000 {
+ reg = <0x0 0x1590000 0x0 0x10000>;
+ interrupts = <0 126 0x4>,
+ <0 121 0x4>,
+ <0 122 0x4>,
+ <0 123 0x4>;
+ };
+
+ msi-bank@15a0000 {
+ reg = <0x0 0x15a0000 0x0 0x10000>;
+ interrupts = <0 160 0x4>,
+ <0 155 0x4>,
+ <0 156 0x4>,
+ <0 157 0x4>;
+ };
+ };
+
+ pcie@3400000 {
+ compatible = "fsl,ls1046a-pcie", "snps,dw-pcie";
+ reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
+ 0x40 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <0 118 0x4>, /* controller interrupt */
+ <0 117 0x4>; /* PME interrupt */
+ interrupt-names = "intr", "pme";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <4>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&msi>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 110 0x4>,
+ <0000 0 0 2 &gic 0 110 0x4>,
+ <0000 0 0 3 &gic 0 110 0x4>,
+ <0000 0 0 4 &gic 0 110 0x4>;
+ };
+
+ pcie@3500000 {
+ compatible = "fsl,ls1046a-pcie", "snps,dw-pcie";
+ reg = <0x00 0x03500000 0x0 0x00100000 /* controller registers */
+ 0x48 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <0 128 0x4>,
+ <0 127 0x4>;
+ interrupt-names = "intr", "pme";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <2>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x48 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&msi>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 120 0x4>,
+ <0000 0 0 2 &gic 0 120 0x4>,
+ <0000 0 0 3 &gic 0 120 0x4>,
+ <0000 0 0 4 &gic 0 120 0x4>;
+ };
+
+ pcie@3600000 {
+ compatible = "fsl,ls1046a-pcie", "snps,dw-pcie";
+ reg = <0x00 0x03600000 0x0 0x00100000 /* controller registers */
+ 0x50 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <0 162 0x4>,
+ <0 161 0x4>;
+ interrupt-names = "intr", "pme";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <2>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x50 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x50 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&msi>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 154 0x4>,
+ <0000 0 0 2 &gic 0 154 0x4>,
+ <0000 0 0 3 &gic 0 154 0x4>,
+ <0000 0 0 4 &gic 0 154 0x4>;
+ };
+ };
+};
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 22+ messages in thread* [PATCH 1/5] arm64: dts: add QorIQ LS1046A SoC support
@ 2016-07-08 10:15 ` shh.xie at gmail.com
0 siblings, 0 replies; 22+ messages in thread
From: shh.xie at gmail.com @ 2016-07-08 10:15 UTC (permalink / raw)
To: linux-arm-kernel
From: Mingkai Hu <Mingkai.Hu@nxp.com>
LS1046A is an SoC with 4 ARMv8 A72 cores and most other IP blocks
are similar to LS1043A which also complies to Freescale Chassis 2.1
spec.
Created LS1046A SoC DTSI file to be included by board level DTS
files.
Signed-off-by: Mihai Bantea <mihai.bantea@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 549 +++++++++++++++++++++++++
1 file changed, 549 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
new file mode 100644
index 0000000..e28a686
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
@@ -0,0 +1,549 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor, Inc.
+ *
+ * Mingkai Hu <mingkai.hu@nxp.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+ compatible = "fsl,ls1046a";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu at 0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x0>;
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu at 1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x1>;
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu2: cpu at 2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x2>;
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ };
+
+ cpu3: cpu at 3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72";
+ reg = <0x3>;
+ clocks = <&clockgen 1 0>;
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ };
+ };
+
+ memory at 80000000 {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0 0x80000000>;
+ /* DRAM space 1, size: 2GiB DRAM */
+ };
+
+ sysclk: sysclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "sysclk";
+ };
+
+ reboot {
+ compatible ="syscon-reboot";
+ regmap = <&dcfg>;
+ offset = <0xb0>;
+ mask = <0x02>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <1 13 0x1>, /* Physical Secure PPI */
+ <1 14 0x1>, /* Physical Non-Secure PPI */
+ <1 11 0x1>, /* Virtual PPI */
+ <1 10 0x1>; /* Hypervisor PPI */
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <0 106 0x4>,
+ <0 107 0x4>,
+ <0 95 0x4>,
+ <0 97 0x4>;
+ interrupt-affinity = <&cpu0>,
+ <&cpu1>,
+ <&cpu2>,
+ <&cpu3>;
+ };
+
+ gic: interrupt-controller at 1400000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x0 0x1410000 0 0x10000>, /* GICD */
+ <0x0 0x1420000 0 0x20000>, /* GICC */
+ <0x0 0x1440000 0 0x20000>, /* GICH */
+ <0x0 0x1460000 0 0x20000>; /* GICV */
+ interrupts = <1 9 0xf08>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clockgen: clocking at 1ee1000 {
+ compatible = "fsl,ls1046a-clockgen";
+ reg = <0x0 0x1ee1000 0x0 0x1000>;
+ #clock-cells = <2>;
+ clocks = <&sysclk>;
+ };
+
+ scfg: scfg at 1570000 {
+ compatible = "fsl,ls1046a-scfg", "syscon";
+ reg = <0x0 0x1570000 0x0 0x10000>;
+ big-endian;
+ };
+
+ dcfg: dcfg at 1ee0000 {
+ compatible = "fsl,ls1046a-dcfg", "syscon";
+ reg = <0x0 0x1ee0000 0x0 0x10000>;
+ big-endian;
+ };
+
+ rcpm: rcpm at 1ee2000 {
+ compatible = "fsl,ls1046a-rcpm", "fsl,qoriq-rcpm-2.1";
+ reg = <0x0 0x1ee2000 0x0 0x10000>;
+ };
+
+ ifc: ifc at 1530000 {
+ compatible = "fsl,ifc", "simple-bus";
+ reg = <0x0 0x1530000 0x0 0x10000>;
+ interrupts = <0 43 0x4>;
+ };
+
+ esdhc: esdhc at 1560000 {
+ compatible = "fsl,ls1046a-esdhc", "fsl,esdhc";
+ reg = <0x0 0x1560000 0x0 0x10000>;
+ interrupts = <0 62 0x4>;
+ clock-frequency = <0>;
+ voltage-ranges = <1800 1800 3300 3300>;
+ sdhci,auto-cmd12;
+ big-endian;
+ bus-width = <4>;
+ };
+
+ dspi: dspi at 2100000 {
+ compatible = "fsl,ls1046a-dspi", "fsl,ls1021a-v1.0-dspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2100000 0x0 0x10000>;
+ interrupts = <0 64 0x4>;
+ clock-names = "dspi";
+ clocks = <&clockgen 4 1>;
+ spi-num-chipselects = <5>;
+ big-endian;
+ status = "disabled";
+ };
+
+ qspi: quadspi at 1550000 {
+ compatible = "fsl,ls1046a-qspi", "fsl,ls1021a-qspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x1550000 0x0 0x10000>,
+ <0x0 0x40000000 0x0 0x10000000>;
+ reg-names = "QuadSPI", "QuadSPI-memory";
+ interrupts = <0 99 0x4>;
+ clock-names = "qspi_en", "qspi";
+ clocks = <&clockgen 4 1>, <&clockgen 4 1>;
+ big-endian;
+ fsl,qspi-has-second-chip;
+ status = "disabled";
+ };
+
+ i2c0: i2c at 2180000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2180000 0x0 0x10000>;
+ interrupts = <0 56 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 1>;
+ dmas = <&edma0 1 39>,
+ <&edma0 1 38>;
+ dma-names = "tx", "rx";
+ status = "disabled";
+ };
+
+ i2c1: i2c at 2190000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2190000 0x0 0x10000>;
+ interrupts = <0 57 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c2: i2c at 21a0000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x21a0000 0x0 0x10000>;
+ interrupts = <0 58 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ i2c3: i2c at 21b0000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x21b0000 0x0 0x10000>;
+ interrupts = <0 59 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+
+ duart0: serial at 21c0500 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x00 0x21c0500 0x0 0x100>;
+ interrupts = <0 54 0x4>;
+ clocks = <&clockgen 4 1>;
+ };
+
+ duart1: serial at 21c0600 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x00 0x21c0600 0x0 0x100>;
+ interrupts = <0 54 0x4>;
+ clocks = <&clockgen 4 1>;
+ };
+
+ duart2: serial at 21d0500 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x0 0x21d0500 0x0 0x100>;
+ interrupts = <0 55 0x4>;
+ clocks = <&clockgen 4 1>;
+ };
+
+ duart3: serial at 21d0600 {
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x0 0x21d0600 0x0 0x100>;
+ interrupts = <0 55 0x4>;
+ clocks = <&clockgen 4 1>;
+ };
+
+ gpio0: gpio at 2300000 {
+ compatible = "fsl,ls1046a-gpio";
+ reg = <0x0 0x2300000 0x0 0x10000>;
+ interrupts = <0 66 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio at 2310000 {
+ compatible = "fsl,ls1046a-gpio";
+ reg = <0x0 0x2310000 0x0 0x10000>;
+ interrupts = <0 67 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio at 2320000 {
+ compatible = "fsl,ls1046a-gpio";
+ reg = <0x0 0x2320000 0x0 0x10000>;
+ interrupts = <0 68 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio at 2330000 {
+ compatible = "fsl,ls1046a-gpio";
+ reg = <0x0 0x2330000 0x0 0x10000>;
+ interrupts = <0 134 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ lpuart0: serial at 2950000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x2950000 0x0 0x1000>;
+ interrupts = <0 48 0x4>;
+ clocks = <&clockgen 0 0>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart1: serial at 2960000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x2960000 0x0 0x1000>;
+ interrupts = <0 49 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart2: serial at 2970000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x2970000 0x0 0x1000>;
+ interrupts = <0 50 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart3: serial at 2980000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x2980000 0x0 0x1000>;
+ interrupts = <0 51 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart4: serial at 2990000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x2990000 0x0 0x1000>;
+ interrupts = <0 52 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ lpuart5: serial at 29a0000 {
+ compatible = "fsl,ls1021a-lpuart";
+ reg = <0x0 0x29a0000 0x0 0x1000>;
+ interrupts = <0 53 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ status = "disabled";
+ };
+
+ wdog0: wdog at 2ad0000 {
+ compatible = "fsl,ls1046a-wdt", "fsl,imx21-wdt";
+ reg = <0x0 0x2ad0000 0x0 0x10000>;
+ interrupts = <0 83 0x4>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "wdog";
+ big-endian;
+ };
+
+ edma0: edma at 2c00000 {
+ #dma-cells = <2>;
+ compatible = "fsl,vf610-edma";
+ reg = <0x0 0x2c00000 0x0 0x10000>,
+ <0x0 0x2c10000 0x0 0x10000>,
+ <0x0 0x2c20000 0x0 0x10000>;
+ interrupts = <0 103 0x4>,
+ <0 103 0x4>;
+ interrupt-names = "edma-tx", "edma-err";
+ dma-channels = <32>;
+ big-endian;
+ clock-names = "dmamux0", "dmamux1";
+ clocks = <&clockgen 4 1>,
+ <&clockgen 4 1>;
+ };
+
+ usb0: usb3 at 2f00000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0x2f00000 0x0 0x10000>;
+ interrupts = <0 60 0x4>;
+ dr_mode = "host";
+ snps,quirk-frame-length-adjustment = <0x20>;
+ };
+
+ usb1: usb3 at 3000000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0x3000000 0x0 0x10000>;
+ interrupts = <0 61 0x4>;
+ dr_mode = "host";
+ snps,quirk-frame-length-adjustment = <0x20>;
+ };
+
+ usb2: usb3 at 3100000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0x3100000 0x0 0x10000>;
+ interrupts = <0 63 0x4>;
+ dr_mode = "host";
+ snps,quirk-frame-length-adjustment = <0x20>;
+ };
+
+ sata: sata at 3200000 {
+ compatible = "fsl,ls1046a-ahci", "fsl,ls1021a-ahci";
+ reg = <0x0 0x3200000 0x0 0x10000>;
+ interrupts = <0 69 0x4>;
+ clocks = <&clockgen 4 1>;
+ };
+
+ msi: msi-controller at 1580000 {
+ compatible = "fsl,ls1046a-msi";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ msi-controller;
+ msi-bank at 1580000 {
+ reg = <0x0 0x1580000 0x0 0x10000>;
+ interrupts = <0 116 0x4>,
+ <0 111 0x4>,
+ <0 112 0x4>,
+ <0 113 0x4>;
+
+ };
+
+ msi-bank at 1590000 {
+ reg = <0x0 0x1590000 0x0 0x10000>;
+ interrupts = <0 126 0x4>,
+ <0 121 0x4>,
+ <0 122 0x4>,
+ <0 123 0x4>;
+ };
+
+ msi-bank at 15a0000 {
+ reg = <0x0 0x15a0000 0x0 0x10000>;
+ interrupts = <0 160 0x4>,
+ <0 155 0x4>,
+ <0 156 0x4>,
+ <0 157 0x4>;
+ };
+ };
+
+ pcie at 3400000 {
+ compatible = "fsl,ls1046a-pcie", "snps,dw-pcie";
+ reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
+ 0x40 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <0 118 0x4>, /* controller interrupt */
+ <0 117 0x4>; /* PME interrupt */
+ interrupt-names = "intr", "pme";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <4>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&msi>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 110 0x4>,
+ <0000 0 0 2 &gic 0 110 0x4>,
+ <0000 0 0 3 &gic 0 110 0x4>,
+ <0000 0 0 4 &gic 0 110 0x4>;
+ };
+
+ pcie at 3500000 {
+ compatible = "fsl,ls1046a-pcie", "snps,dw-pcie";
+ reg = <0x00 0x03500000 0x0 0x00100000 /* controller registers */
+ 0x48 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <0 128 0x4>,
+ <0 127 0x4>;
+ interrupt-names = "intr", "pme";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <2>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x48 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&msi>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 120 0x4>,
+ <0000 0 0 2 &gic 0 120 0x4>,
+ <0000 0 0 3 &gic 0 120 0x4>,
+ <0000 0 0 4 &gic 0 120 0x4>;
+ };
+
+ pcie at 3600000 {
+ compatible = "fsl,ls1046a-pcie", "snps,dw-pcie";
+ reg = <0x00 0x03600000 0x0 0x00100000 /* controller registers */
+ 0x50 0x00000000 0x0 0x00002000>; /* configuration space */
+ reg-names = "regs", "config";
+ interrupts = <0 162 0x4>,
+ <0 161 0x4>;
+ interrupt-names = "intr", "pme";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <2>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x50 0x00010000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x50 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ msi-parent = <&msi>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 154 0x4>,
+ <0000 0 0 2 &gic 0 154 0x4>,
+ <0000 0 0 3 &gic 0 154 0x4>,
+ <0000 0 0 4 &gic 0 154 0x4>;
+ };
+ };
+};
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 22+ messages in thread[parent not found: <1467972944-12293-2-git-send-email-shh.xie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>]
* Re: [PATCH 1/5] arm64: dts: add QorIQ LS1046A SoC support
2016-07-08 10:15 ` shh.xie at gmail.com
@ 2016-07-08 12:00 ` Arnd Bergmann
-1 siblings, 0 replies; 22+ messages in thread
From: Arnd Bergmann @ 2016-07-08 12:00 UTC (permalink / raw)
To: shh.xie-Re5JQEeQqe8AvxtiuMwx3w
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
pawel.moll-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8, Mingkai Hu,
Mihai Bantea, Gong Qianyu, Minghuan Lian, Hou Zhiqiang,
Shaohui Xie
On Friday, July 8, 2016 6:15:40 PM CEST shh.xie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org wrote:
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x0 0x80000000 0 0x80000000>;
> + /* DRAM space 1, size: 2GiB DRAM */
> + };
The memory size is usually in the .dts file, unless this is on-chip
eDRAM.
> + clockgen: clocking@1ee1000 {
> + compatible = "fsl,ls1046a-clockgen";
> + scfg: scfg@1570000 {
> + compatible = "fsl,ls1046a-scfg", "syscon";
> + dcfg: dcfg@1ee0000 {
> + compatible = "fsl,ls1046a-dcfg", "syscon";
None of the fsl,ls1046a-* devices seem to have any binding documentation.
> + wdog0: wdog@2ad0000 {
watchdog@2ad0000
> + usb0: usb3@2f00000 {
usb@2f00000
> + pcie@3400000 {
> + compatible = "fsl,ls1046a-pcie", "snps,dw-pcie";
> + reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
> + 0x40 0x00000000 0x0 0x00002000>; /* configuration space */
> + reg-names = "regs", "config";
> + interrupts = <0 118 0x4>, /* controller interrupt */
> + <0 117 0x4>; /* PME interrupt */
> + interrupt-names = "intr", "pme";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + num-lanes = <4>;
> + bus-range = <0x0 0xff>;
> + ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */
> + 0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
No prefetchable memory area?
> + msi-parent = <&msi>;
You seem to have a gic-400, could you use that as the MSI sink instead?
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 7>;
> + interrupt-map = <0000 0 0 1 &gic 0 110 0x4>,
> + <0000 0 0 2 &gic 0 110 0x4>,
> + <0000 0 0 3 &gic 0 110 0x4>,
> + <0000 0 0 4 &gic 0 110 0x4>;
> + };
>
If the four interrupts are all the same, why do you have separate entries?
Arnd
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 22+ messages in thread* [PATCH 1/5] arm64: dts: add QorIQ LS1046A SoC support
@ 2016-07-08 12:00 ` Arnd Bergmann
0 siblings, 0 replies; 22+ messages in thread
From: Arnd Bergmann @ 2016-07-08 12:00 UTC (permalink / raw)
To: linux-arm-kernel
On Friday, July 8, 2016 6:15:40 PM CEST shh.xie at gmail.com wrote:
> +
> + memory at 80000000 {
> + device_type = "memory";
> + reg = <0x0 0x80000000 0 0x80000000>;
> + /* DRAM space 1, size: 2GiB DRAM */
> + };
The memory size is usually in the .dts file, unless this is on-chip
eDRAM.
> + clockgen: clocking at 1ee1000 {
> + compatible = "fsl,ls1046a-clockgen";
> + scfg: scfg at 1570000 {
> + compatible = "fsl,ls1046a-scfg", "syscon";
> + dcfg: dcfg at 1ee0000 {
> + compatible = "fsl,ls1046a-dcfg", "syscon";
None of the fsl,ls1046a-* devices seem to have any binding documentation.
> + wdog0: wdog at 2ad0000 {
watchdog at 2ad0000
> + usb0: usb3 at 2f00000 {
usb at 2f00000
> + pcie at 3400000 {
> + compatible = "fsl,ls1046a-pcie", "snps,dw-pcie";
> + reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
> + 0x40 0x00000000 0x0 0x00002000>; /* configuration space */
> + reg-names = "regs", "config";
> + interrupts = <0 118 0x4>, /* controller interrupt */
> + <0 117 0x4>; /* PME interrupt */
> + interrupt-names = "intr", "pme";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + num-lanes = <4>;
> + bus-range = <0x0 0xff>;
> + ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */
> + 0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
No prefetchable memory area?
> + msi-parent = <&msi>;
You seem to have a gic-400, could you use that as the MSI sink instead?
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 7>;
> + interrupt-map = <0000 0 0 1 &gic 0 110 0x4>,
> + <0000 0 0 2 &gic 0 110 0x4>,
> + <0000 0 0 3 &gic 0 110 0x4>,
> + <0000 0 0 4 &gic 0 110 0x4>;
> + };
>
If the four interrupts are all the same, why do you have separate entries?
Arnd
^ permalink raw reply [flat|nested] 22+ messages in thread* RE: [PATCH 1/5] arm64: dts: add QorIQ LS1046A SoC support
2016-07-08 12:00 ` Arnd Bergmann
@ 2016-08-18 10:27 ` Shaohui Xie
-1 siblings, 0 replies; 22+ messages in thread
From: Shaohui Xie @ 2016-08-18 10:27 UTC (permalink / raw)
To: Arnd Bergmann
Cc: mark.rutland, devicetree, Mihai Emilian Bantea, pawel.moll,
ijc+devicetree, catalin.marinas, Zhiqiang Hou, will.deacon,
Minghuan Lian, robh+dt, Mingkai Hu, galak, Qianyu Gong,
linux-arm-kernel
Hello Arnd,
Thank you for reviewing!
I'm seriously Sorry for the late response! I was on business travel on a project and had been very busy for a long time.
Please see inline.
Regards,
Shaohui
> -----Original Message-----
> From: Arnd Bergmann [mailto:arnd@arndb.de]
> Sent: Friday, July 08, 2016 8:00 PM
> To: shh.xie@gmail.com
> Cc: devicetree@vger.kernel.org; robh+dt@kernel.org; mark.rutland@arm.com;
> pawel.moll@arm.com; ijc+devicetree@hellion.org.uk; galak@codeaurora.org;
> linux-arm-kernel@lists.infradead.org; catalin.marinas@arm.com;
> will.deacon@arm.com; Mingkai Hu <mingkai.hu@nxp.com>; Mihai Emilian Bantea
> <mihai.bantea@nxp.com>; Qianyu Gong <qianyu.gong@nxp.com>; Minghuan Lian
> <minghuan.lian@nxp.com>; Zhiqiang Hou <zhiqiang.hou@nxp.com>; Shaohui Xie
> <shaohui.xie@nxp.com>
> Subject: Re: [PATCH 1/5] arm64: dts: add QorIQ LS1046A SoC support
>
> On Friday, July 8, 2016 6:15:40 PM CEST shh.xie@gmail.com wrote:
> > +
> > + memory@80000000 {
> > + device_type = "memory";
> > + reg = <0x0 0x80000000 0 0x80000000>;
> > + /* DRAM space 1, size: 2GiB DRAM */
> > + };
>
> The memory size is usually in the .dts file, unless this is on-chip eDRAM.
[S.H] The memory size will be fixup by U-boot, if it's not proper to have it in .dtsti,
How about remove it?
> > + clockgen: clocking@1ee1000 {
> > + compatible = "fsl,ls1046a-clockgen";
>
> > + scfg: scfg@1570000 {
> > + compatible = "fsl,ls1046a-scfg", "syscon";
>
> > + dcfg: dcfg@1ee0000 {
> > + compatible = "fsl,ls1046a-dcfg", "syscon";
>
> None of the fsl,ls1046a-* devices seem to have any binding documentation.
[S.H] Will update binding for fsl,ls1046-* devices in next version.
>
> > + wdog0: wdog@2ad0000 {
>
> watchdog@2ad0000
[S.H] Will fix it.
>
> > + usb0: usb3@2f00000 {
>
> usb@2f00000
[S.H] Will fix it.
>
> > + pcie@3400000 {
> > + compatible = "fsl,ls1046a-pcie", "snps,dw-pcie";
> > + reg = <0x00 0x03400000 0x0 0x00100000 /* controller
> registers */
> > + 0x40 0x00000000 0x0 0x00002000>; /* configuration
> space */
> > + reg-names = "regs", "config";
> > + interrupts = <0 118 0x4>, /* controller interrupt */
> > + <0 117 0x4>; /* PME interrupt */
> > + interrupt-names = "intr", "pme";
> > + #address-cells = <3>;
> > + #size-cells = <2>;
> > + device_type = "pci";
> > + num-lanes = <4>;
> > + bus-range = <0x0 0xff>;
> > + ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000
> 0x0 0x00010000 /* downstream I/O */
> > + 0x82000000 0x0 0x40000000 0x40 0x40000000
> 0x0 0x40000000>; /*
> > +non-prefetchable memory */
>
> No prefetchable memory area?
>
> > + msi-parent = <&msi>;
>
> You seem to have a gic-400, could you use that as the MSI sink instead?
>
> > + #interrupt-cells = <1>;
> > + interrupt-map-mask = <0 0 0 7>;
> > + interrupt-map = <0000 0 0 1 &gic 0 110 0x4>,
> > + <0000 0 0 2 &gic 0 110 0x4>,
> > + <0000 0 0 3 &gic 0 110 0x4>,
> > + <0000 0 0 4 &gic 0 110 0x4>;
> > + };
> >
>
> If the four interrupts are all the same, why do you have separate entries?
[S.H] We are working on refining the MSI driver and the MSI node will also be changed,
so the MSI and PCIe node will be added together with the MSI driver updates.
In the next version, I will drop the MSI node and PCIe node.
Thank you!
^ permalink raw reply [flat|nested] 22+ messages in thread* [PATCH 1/5] arm64: dts: add QorIQ LS1046A SoC support
@ 2016-08-18 10:27 ` Shaohui Xie
0 siblings, 0 replies; 22+ messages in thread
From: Shaohui Xie @ 2016-08-18 10:27 UTC (permalink / raw)
To: linux-arm-kernel
Hello Arnd,
Thank you for reviewing!
I'm seriously Sorry for the late response! I was on business travel on a project and had been very busy for a long time.
Please see inline.
Regards,
Shaohui
> -----Original Message-----
> From: Arnd Bergmann [mailto:arnd at arndb.de]
> Sent: Friday, July 08, 2016 8:00 PM
> To: shh.xie at gmail.com
> Cc: devicetree at vger.kernel.org; robh+dt at kernel.org; mark.rutland at arm.com;
> pawel.moll at arm.com; ijc+devicetree at hellion.org.uk; galak at codeaurora.org;
> linux-arm-kernel at lists.infradead.org; catalin.marinas at arm.com;
> will.deacon at arm.com; Mingkai Hu <mingkai.hu@nxp.com>; Mihai Emilian Bantea
> <mihai.bantea@nxp.com>; Qianyu Gong <qianyu.gong@nxp.com>; Minghuan Lian
> <minghuan.lian@nxp.com>; Zhiqiang Hou <zhiqiang.hou@nxp.com>; Shaohui Xie
> <shaohui.xie@nxp.com>
> Subject: Re: [PATCH 1/5] arm64: dts: add QorIQ LS1046A SoC support
>
> On Friday, July 8, 2016 6:15:40 PM CEST shh.xie at gmail.com wrote:
> > +
> > + memory at 80000000 {
> > + device_type = "memory";
> > + reg = <0x0 0x80000000 0 0x80000000>;
> > + /* DRAM space 1, size: 2GiB DRAM */
> > + };
>
> The memory size is usually in the .dts file, unless this is on-chip eDRAM.
[S.H] The memory size will be fixup by U-boot, if it's not proper to have it in .dtsti,
How about remove it?
> > + clockgen: clocking at 1ee1000 {
> > + compatible = "fsl,ls1046a-clockgen";
>
> > + scfg: scfg at 1570000 {
> > + compatible = "fsl,ls1046a-scfg", "syscon";
>
> > + dcfg: dcfg at 1ee0000 {
> > + compatible = "fsl,ls1046a-dcfg", "syscon";
>
> None of the fsl,ls1046a-* devices seem to have any binding documentation.
[S.H] Will update binding for fsl,ls1046-* devices in next version.
>
> > + wdog0: wdog at 2ad0000 {
>
> watchdog at 2ad0000
[S.H] Will fix it.
>
> > + usb0: usb3 at 2f00000 {
>
> usb at 2f00000
[S.H] Will fix it.
>
> > + pcie at 3400000 {
> > + compatible = "fsl,ls1046a-pcie", "snps,dw-pcie";
> > + reg = <0x00 0x03400000 0x0 0x00100000 /* controller
> registers */
> > + 0x40 0x00000000 0x0 0x00002000>; /* configuration
> space */
> > + reg-names = "regs", "config";
> > + interrupts = <0 118 0x4>, /* controller interrupt */
> > + <0 117 0x4>; /* PME interrupt */
> > + interrupt-names = "intr", "pme";
> > + #address-cells = <3>;
> > + #size-cells = <2>;
> > + device_type = "pci";
> > + num-lanes = <4>;
> > + bus-range = <0x0 0xff>;
> > + ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000
> 0x0 0x00010000 /* downstream I/O */
> > + 0x82000000 0x0 0x40000000 0x40 0x40000000
> 0x0 0x40000000>; /*
> > +non-prefetchable memory */
>
> No prefetchable memory area?
>
> > + msi-parent = <&msi>;
>
> You seem to have a gic-400, could you use that as the MSI sink instead?
>
> > + #interrupt-cells = <1>;
> > + interrupt-map-mask = <0 0 0 7>;
> > + interrupt-map = <0000 0 0 1 &gic 0 110 0x4>,
> > + <0000 0 0 2 &gic 0 110 0x4>,
> > + <0000 0 0 3 &gic 0 110 0x4>,
> > + <0000 0 0 4 &gic 0 110 0x4>;
> > + };
> >
>
> If the four interrupts are all the same, why do you have separate entries?
[S.H] We are working on refining the MSI driver and the MSI node will also be changed,
so the MSI and PCIe node will be added together with the MSI driver updates.
In the next version, I will drop the MSI node and PCIe node.
Thank you!
^ permalink raw reply [flat|nested] 22+ messages in thread* Re: [PATCH 1/5] arm64: dts: add QorIQ LS1046A SoC support
2016-08-18 10:27 ` Shaohui Xie
@ 2016-08-23 10:04 ` Arnd Bergmann
-1 siblings, 0 replies; 22+ messages in thread
From: Arnd Bergmann @ 2016-08-23 10:04 UTC (permalink / raw)
To: Shaohui Xie
Cc: mark.rutland, devicetree, Mihai Emilian Bantea, pawel.moll,
ijc+devicetree, catalin.marinas, Zhiqiang Hou, will.deacon,
Minghuan Lian, robh+dt, Mingkai Hu, galak, Qianyu Gong,
linux-arm-kernel
On Thursday, August 18, 2016 10:27:36 AM CEST Shaohui Xie wrote:
> Hello Arnd,
>
> Thank you for reviewing!
>
> I'm seriously Sorry for the late response! I was on business travel on a project and had been very busy for a long time.
No worries.
> > -----Original Message-----
> > From: Arnd Bergmann [mailto:arnd@arndb.de]
> > Sent: Friday, July 08, 2016 8:00 PM
> > On Friday, July 8, 2016 6:15:40 PM CEST shh.xie@gmail.com wrote:
> > > +
> > > + memory@80000000 {
> > > + device_type = "memory";
> > > + reg = <0x0 0x80000000 0 0x80000000>;
> > > + /* DRAM space 1, size: 2GiB DRAM */
> > > + };
> >
> > The memory size is usually in the .dts file, unless this is on-chip eDRAM.
> [S.H] The memory size will be fixup by U-boot, if it's not proper to have it in .dtsti,
> How about remove it?
>
Sounds fine to me. A lot of board specific files have a memory node
regardless of the override, but I don't see a reason to require it.
Arnd
^ permalink raw reply [flat|nested] 22+ messages in thread* [PATCH 1/5] arm64: dts: add QorIQ LS1046A SoC support
@ 2016-08-23 10:04 ` Arnd Bergmann
0 siblings, 0 replies; 22+ messages in thread
From: Arnd Bergmann @ 2016-08-23 10:04 UTC (permalink / raw)
To: linux-arm-kernel
On Thursday, August 18, 2016 10:27:36 AM CEST Shaohui Xie wrote:
> Hello Arnd,
>
> Thank you for reviewing!
>
> I'm seriously Sorry for the late response! I was on business travel on a project and had been very busy for a long time.
No worries.
> > -----Original Message-----
> > From: Arnd Bergmann [mailto:arnd at arndb.de]
> > Sent: Friday, July 08, 2016 8:00 PM
> > On Friday, July 8, 2016 6:15:40 PM CEST shh.xie at gmail.com wrote:
> > > +
> > > + memory at 80000000 {
> > > + device_type = "memory";
> > > + reg = <0x0 0x80000000 0 0x80000000>;
> > > + /* DRAM space 1, size: 2GiB DRAM */
> > > + };
> >
> > The memory size is usually in the .dts file, unless this is on-chip eDRAM.
> [S.H] The memory size will be fixup by U-boot, if it's not proper to have it in .dtsti,
> How about remove it?
>
Sounds fine to me. A lot of board specific files have a memory node
regardless of the override, but I don't see a reason to require it.
Arnd
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH 2/5] Documentation: DT: Add entry for QorIQ LS1046A-RDB board
2016-07-08 10:15 ` shh.xie at gmail.com
@ 2016-07-08 10:15 ` shh.xie at gmail.com
-1 siblings, 0 replies; 22+ messages in thread
From: shh.xie @ 2016-07-08 10:15 UTC (permalink / raw)
To: devicetree, robh+dt, mark.rutland, pawel.moll, ijc+devicetree,
galak, linux-arm-kernel, catalin.marinas, will.deacon
Cc: Shaohui Xie
From: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
Documentation/devicetree/bindings/arm/fsl.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index dbbc095..cabd575 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -139,6 +139,10 @@ LS1043A ARMv8 based QDS Board
Required root node properties:
- compatible = "fsl,ls1043a-qds", "fsl,ls1043a";
+LS1046A ARMv8 based RDB Board
+Required root node properties:
+ - compatible = "fsl,ls1046a-rdb", "fsl,ls1046a";
+
LS2080A ARMv8 based Simulator model
Required root node properties:
- compatible = "fsl,ls2080a-simu", "fsl,ls2080a";
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 22+ messages in thread* [PATCH 2/5] Documentation: DT: Add entry for QorIQ LS1046A-RDB board
@ 2016-07-08 10:15 ` shh.xie at gmail.com
0 siblings, 0 replies; 22+ messages in thread
From: shh.xie at gmail.com @ 2016-07-08 10:15 UTC (permalink / raw)
To: linux-arm-kernel
From: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
Documentation/devicetree/bindings/arm/fsl.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index dbbc095..cabd575 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -139,6 +139,10 @@ LS1043A ARMv8 based QDS Board
Required root node properties:
- compatible = "fsl,ls1043a-qds", "fsl,ls1043a";
+LS1046A ARMv8 based RDB Board
+Required root node properties:
+ - compatible = "fsl,ls1046a-rdb", "fsl,ls1046a";
+
LS2080A ARMv8 based Simulator model
Required root node properties:
- compatible = "fsl,ls2080a-simu", "fsl,ls2080a";
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 22+ messages in thread[parent not found: <1467972944-12293-3-git-send-email-shh.xie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>]
* Re: [PATCH 2/5] Documentation: DT: Add entry for QorIQ LS1046A-RDB board
2016-07-08 10:15 ` shh.xie at gmail.com
@ 2016-07-16 0:08 ` Rob Herring
-1 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2016-07-16 0:08 UTC (permalink / raw)
To: shh.xie-Re5JQEeQqe8AvxtiuMwx3w
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, mark.rutland-5wv7dgnIgG8,
pawel.moll-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8,
Shaohui Xie
On Fri, Jul 08, 2016 at 06:15:41PM +0800, shh.xie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org wrote:
> From: Shaohui Xie <Shaohui.Xie-3arQi8VN3Tc@public.gmane.org>
>
> Signed-off-by: Shaohui Xie <Shaohui.Xie-3arQi8VN3Tc@public.gmane.org>
> ---
> Documentation/devicetree/bindings/arm/fsl.txt | 4 ++++
> 1 file changed, 4 insertions(+)
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH 2/5] Documentation: DT: Add entry for QorIQ LS1046A-RDB board
@ 2016-07-16 0:08 ` Rob Herring
0 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2016-07-16 0:08 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jul 08, 2016 at 06:15:41PM +0800, shh.xie at gmail.com wrote:
> From: Shaohui Xie <Shaohui.Xie@nxp.com>
>
> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.txt | 4 ++++
> 1 file changed, 4 insertions(+)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH 3/5] arm64: dts: add LS1046A-RDB board support
2016-07-08 10:15 ` shh.xie at gmail.com
@ 2016-07-08 10:15 ` shh.xie at gmail.com
-1 siblings, 0 replies; 22+ messages in thread
From: shh.xie @ 2016-07-08 10:15 UTC (permalink / raw)
To: devicetree, robh+dt, mark.rutland, pawel.moll, ijc+devicetree,
galak, linux-arm-kernel, catalin.marinas, will.deacon
Cc: Shaohui Xie, Mingkai Hu
From: Mingkai Hu <Mingkai.Hu@nxp.com>
The LS1046A reference design board (RDB) is a high-performance computing,
evaluation, and development platform that supports the LS1046A SoC.
Signed-off-by: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts | 138 ++++++++++++++++++++++
2 files changed, 139 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 1b7783d..9c81b9e 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
new file mode 100644
index 0000000..cafe8e4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
@@ -0,0 +1,138 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor, Inc.
+ *
+ * Mingkai Hu <mingkai.hu@nxp.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+/include/ "fsl-ls1046a.dtsi"
+
+/ {
+ model = "LS1046A RDB Board";
+ compatible = "fsl,ls1046a-rdb", "fsl,ls1046a";
+};
+
+&duart0 {
+ status = "okay";
+};
+
+&duart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ ina220@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <1000>;
+ };
+
+ temp-sensor@4c {
+ compatible = "adi,adt7461";
+ reg = <0x4c>;
+ };
+
+ eeprom@56 {
+ compatible = "atmel,24c512";
+ reg = <0x52>;
+ };
+
+ eeprom@57 {
+ compatible = "atmel,24c512";
+ reg = <0x53>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+};
+
+&ifc {
+ status = "okay";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* NAND Flashe and CPLD on board */
+ ranges = <0x0 0x0 0x0 0x7e800000 0x00010000
+ 0x2 0x0 0x0 0x7fb00000 0x00000100>;
+
+ nand@0,0 {
+ compatible = "fsl,ifc-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0 0x0 0x10000>;
+ };
+
+ cpld: board-control@2,0 {
+ compatible = "fsl,ls1046ardb-cpld";
+ reg = <0x2 0x0 0x0000100>;
+ };
+};
+
+&qspi {
+ num-cs = <2>;
+ bus-num = <0>;
+ status = "okay";
+
+ qflash0: s25fs512s@0 {
+ compatible = "spansion,m25p80";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+
+ qflash1: s25fs512s@1 {
+ compatible = "spansion,m25p80";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <20000000>;
+ reg = <1>;
+ };
+};
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 22+ messages in thread* [PATCH 3/5] arm64: dts: add LS1046A-RDB board support
@ 2016-07-08 10:15 ` shh.xie at gmail.com
0 siblings, 0 replies; 22+ messages in thread
From: shh.xie at gmail.com @ 2016-07-08 10:15 UTC (permalink / raw)
To: linux-arm-kernel
From: Mingkai Hu <Mingkai.Hu@nxp.com>
The LS1046A reference design board (RDB) is a high-performance computing,
evaluation, and development platform that supports the LS1046A SoC.
Signed-off-by: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts | 138 ++++++++++++++++++++++
2 files changed, 139 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 1b7783d..9c81b9e 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
new file mode 100644
index 0000000..cafe8e4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
@@ -0,0 +1,138 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor, Inc.
+ *
+ * Mingkai Hu <mingkai.hu@nxp.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+/include/ "fsl-ls1046a.dtsi"
+
+/ {
+ model = "LS1046A RDB Board";
+ compatible = "fsl,ls1046a-rdb", "fsl,ls1046a";
+};
+
+&duart0 {
+ status = "okay";
+};
+
+&duart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ ina220 at 40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <1000>;
+ };
+
+ temp-sensor at 4c {
+ compatible = "adi,adt7461";
+ reg = <0x4c>;
+ };
+
+ eeprom at 56 {
+ compatible = "atmel,24c512";
+ reg = <0x52>;
+ };
+
+ eeprom at 57 {
+ compatible = "atmel,24c512";
+ reg = <0x53>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+
+ rtc at 51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+};
+
+&ifc {
+ status = "okay";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* NAND Flashe and CPLD on board */
+ ranges = <0x0 0x0 0x0 0x7e800000 0x00010000
+ 0x2 0x0 0x0 0x7fb00000 0x00000100>;
+
+ nand at 0,0 {
+ compatible = "fsl,ifc-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x0 0x0 0x10000>;
+ };
+
+ cpld: board-control at 2,0 {
+ compatible = "fsl,ls1046ardb-cpld";
+ reg = <0x2 0x0 0x0000100>;
+ };
+};
+
+&qspi {
+ num-cs = <2>;
+ bus-num = <0>;
+ status = "okay";
+
+ qflash0: s25fs512s at 0 {
+ compatible = "spansion,m25p80";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+
+ qflash1: s25fs512s at 1 {
+ compatible = "spansion,m25p80";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <20000000>;
+ reg = <1>;
+ };
+};
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [PATCH 4/5] Documentation: DT: Add entry for QorIQ LS1046A-QDS board
2016-07-08 10:15 ` shh.xie at gmail.com
@ 2016-07-08 10:15 ` shh.xie at gmail.com
-1 siblings, 0 replies; 22+ messages in thread
From: shh.xie @ 2016-07-08 10:15 UTC (permalink / raw)
To: devicetree, robh+dt, mark.rutland, pawel.moll, ijc+devicetree,
galak, linux-arm-kernel, catalin.marinas, will.deacon
Cc: Shaohui Xie
From: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
Documentation/devicetree/bindings/arm/fsl.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index cabd575..b6a9637 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -139,6 +139,10 @@ LS1043A ARMv8 based QDS Board
Required root node properties:
- compatible = "fsl,ls1043a-qds", "fsl,ls1043a";
+LS1046A ARMv8 based QDS Board
+Required root node properties:
+ - compatible = "fsl,ls1046a-qds", "fsl,ls1046a";
+
LS1046A ARMv8 based RDB Board
Required root node properties:
- compatible = "fsl,ls1046a-rdb", "fsl,ls1046a";
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 22+ messages in thread* [PATCH 4/5] Documentation: DT: Add entry for QorIQ LS1046A-QDS board
@ 2016-07-08 10:15 ` shh.xie at gmail.com
0 siblings, 0 replies; 22+ messages in thread
From: shh.xie at gmail.com @ 2016-07-08 10:15 UTC (permalink / raw)
To: linux-arm-kernel
From: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
Documentation/devicetree/bindings/arm/fsl.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index cabd575..b6a9637 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -139,6 +139,10 @@ LS1043A ARMv8 based QDS Board
Required root node properties:
- compatible = "fsl,ls1043a-qds", "fsl,ls1043a";
+LS1046A ARMv8 based QDS Board
+Required root node properties:
+ - compatible = "fsl,ls1046a-qds", "fsl,ls1046a";
+
LS1046A ARMv8 based RDB Board
Required root node properties:
- compatible = "fsl,ls1046a-rdb", "fsl,ls1046a";
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 22+ messages in thread[parent not found: <1467972944-12293-5-git-send-email-shh.xie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>]
* Re: [PATCH 4/5] Documentation: DT: Add entry for QorIQ LS1046A-QDS board
2016-07-08 10:15 ` shh.xie at gmail.com
@ 2016-07-16 0:09 ` Rob Herring
-1 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2016-07-16 0:09 UTC (permalink / raw)
To: shh.xie-Re5JQEeQqe8AvxtiuMwx3w
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, mark.rutland-5wv7dgnIgG8,
pawel.moll-5wv7dgnIgG8, ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
galak-sgV2jX0FEOL9JmXXK+q4OQ,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8,
Shaohui Xie
On Fri, Jul 08, 2016 at 06:15:43PM +0800, shh.xie-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org wrote:
> From: Shaohui Xie <Shaohui.Xie-3arQi8VN3Tc@public.gmane.org>
>
> Signed-off-by: Shaohui Xie <Shaohui.Xie-3arQi8VN3Tc@public.gmane.org>
> ---
> Documentation/devicetree/bindings/arm/fsl.txt | 4 ++++
> 1 file changed, 4 insertions(+)
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH 4/5] Documentation: DT: Add entry for QorIQ LS1046A-QDS board
@ 2016-07-16 0:09 ` Rob Herring
0 siblings, 0 replies; 22+ messages in thread
From: Rob Herring @ 2016-07-16 0:09 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jul 08, 2016 at 06:15:43PM +0800, shh.xie at gmail.com wrote:
> From: Shaohui Xie <Shaohui.Xie@nxp.com>
>
> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.txt | 4 ++++
> 1 file changed, 4 insertions(+)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 22+ messages in thread
* [PATCH 5/5] arm64: dts: add LS1046A-QDS board support
2016-07-08 10:15 ` shh.xie at gmail.com
@ 2016-07-08 10:15 ` shh.xie at gmail.com
-1 siblings, 0 replies; 22+ messages in thread
From: shh.xie @ 2016-07-08 10:15 UTC (permalink / raw)
To: devicetree, robh+dt, mark.rutland, pawel.moll, ijc+devicetree,
galak, linux-arm-kernel, catalin.marinas, will.deacon
Cc: Shaohui Xie
From: Shaohui Xie <Shaohui.Xie@nxp.com>
The LS1046A QorIQ development system (QDS) board is a high-performance
computing, evaluation, development, and test platform supporting the
LS1046A SoC.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts | 209 ++++++++++++++++++++++
2 files changed, 210 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 9c81b9e..6602718 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
new file mode 100644
index 0000000..5234f6e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
@@ -0,0 +1,209 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor, Inc.
+ *
+ * Shaohui Xie <Shaohui.Xie@nxp.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+/include/ "fsl-ls1046a.dtsi"
+
+/ {
+ model = "LS1046A QDS Board";
+ compatible = "fsl,ls1046a-qds", "fsl,ls1046a";
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ gpio3 = &gpio3;
+ serial0 = &lpuart0;
+ serial1 = &lpuart1;
+ serial2 = &lpuart2;
+ serial3 = &lpuart3;
+ serial4 = &lpuart4;
+ serial5 = &lpuart5;
+ };
+};
+
+&dspi {
+ bus-num = <0>;
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a11", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ };
+
+ flash@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst25wf040b", "jedec,spi-nor";
+ spi-cpol;
+ spi-cpha;
+ reg = <1>;
+ spi-max-frequency = <10000000>;
+ };
+
+ flash@2 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "en25s64", "jedec,spi-nor";
+ spi-cpol;
+ spi-cpha;
+ reg = <2>;
+ spi-max-frequency = <10000000>;
+ };
+};
+
+&duart0 {
+ status = "okay";
+};
+
+&duart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ pca9547@77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ ina220@40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <1000>;
+ };
+
+ ina220@41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ rtc@51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ /* IRQ10_B */
+ interrupts = <0 150 0x4>;
+ };
+
+ eeprom@56 {
+ compatible = "atmel,24c512";
+ reg = <0x56>;
+ };
+
+ eeprom@57 {
+ compatible = "atmel,24c512";
+ reg = <0x57>;
+ };
+
+ temp-sensor@4c {
+ compatible = "adi,adt7461a";
+ reg = <0x4c>;
+ };
+ };
+ };
+};
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* NOR, NAND Flashes and FPGA on board */
+ ranges = <0x0 0x0 0x0 0x60000000 0x08000000
+ 0x1 0x0 0x0 0x7e800000 0x00010000
+ 0x2 0x0 0x0 0x7fb00000 0x00000100>;
+ status = "okay";
+
+ nor@0,0 {
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand@1,0 {
+ compatible = "fsl,ifc-nand";
+ reg = <0x1 0x0 0x10000>;
+ };
+
+ fpga: board-control@2,0 {
+ compatible = "fsl,ls1046aqds-fpga", "fsl,fpga-qixis";
+ reg = <0x2 0x0 0x0000100>;
+ };
+};
+
+&lpuart0 {
+ status = "okay";
+};
+
+&qspi {
+ num-cs = <2>;
+ bus-num = <0>;
+ status = "okay";
+
+ qflash0: s25fl128s@0 {
+ compatible = "spansion,m25p80";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 22+ messages in thread* [PATCH 5/5] arm64: dts: add LS1046A-QDS board support
@ 2016-07-08 10:15 ` shh.xie at gmail.com
0 siblings, 0 replies; 22+ messages in thread
From: shh.xie at gmail.com @ 2016-07-08 10:15 UTC (permalink / raw)
To: linux-arm-kernel
From: Shaohui Xie <Shaohui.Xie@nxp.com>
The LS1046A QorIQ development system (QDS) board is a high-performance
computing, evaluation, development, and test platform supporting the
LS1046A SoC.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts | 209 ++++++++++++++++++++++
2 files changed, 210 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 9c81b9e..6602718 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -1,5 +1,6 @@
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
new file mode 100644
index 0000000..5234f6e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
@@ -0,0 +1,209 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1046A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor, Inc.
+ *
+ * Shaohui Xie <Shaohui.Xie@nxp.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+/include/ "fsl-ls1046a.dtsi"
+
+/ {
+ model = "LS1046A QDS Board";
+ compatible = "fsl,ls1046a-qds", "fsl,ls1046a";
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ gpio3 = &gpio3;
+ serial0 = &lpuart0;
+ serial1 = &lpuart1;
+ serial2 = &lpuart2;
+ serial3 = &lpuart3;
+ serial4 = &lpuart4;
+ serial5 = &lpuart5;
+ };
+};
+
+&dspi {
+ bus-num = <0>;
+ status = "okay";
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a11", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ };
+
+ flash at 1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "sst25wf040b", "jedec,spi-nor";
+ spi-cpol;
+ spi-cpha;
+ reg = <1>;
+ spi-max-frequency = <10000000>;
+ };
+
+ flash at 2 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "en25s64", "jedec,spi-nor";
+ spi-cpol;
+ spi-cpha;
+ reg = <2>;
+ spi-max-frequency = <10000000>;
+ };
+};
+
+&duart0 {
+ status = "okay";
+};
+
+&duart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ pca9547 at 77 {
+ compatible = "nxp,pca9547";
+ reg = <0x77>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x2>;
+
+ ina220 at 40 {
+ compatible = "ti,ina220";
+ reg = <0x40>;
+ shunt-resistor = <1000>;
+ };
+
+ ina220 at 41 {
+ compatible = "ti,ina220";
+ reg = <0x41>;
+ shunt-resistor = <1000>;
+ };
+ };
+
+ i2c at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x3>;
+
+ rtc at 51 {
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ /* IRQ10_B */
+ interrupts = <0 150 0x4>;
+ };
+
+ eeprom at 56 {
+ compatible = "atmel,24c512";
+ reg = <0x56>;
+ };
+
+ eeprom at 57 {
+ compatible = "atmel,24c512";
+ reg = <0x57>;
+ };
+
+ temp-sensor at 4c {
+ compatible = "adi,adt7461a";
+ reg = <0x4c>;
+ };
+ };
+ };
+};
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* NOR, NAND Flashes and FPGA on board */
+ ranges = <0x0 0x0 0x0 0x60000000 0x08000000
+ 0x1 0x0 0x0 0x7e800000 0x00010000
+ 0x2 0x0 0x0 0x7fb00000 0x00000100>;
+ status = "okay";
+
+ nor at 0,0 {
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x8000000>;
+ bank-width = <2>;
+ device-width = <1>;
+ };
+
+ nand at 1,0 {
+ compatible = "fsl,ifc-nand";
+ reg = <0x1 0x0 0x10000>;
+ };
+
+ fpga: board-control at 2,0 {
+ compatible = "fsl,ls1046aqds-fpga", "fsl,fpga-qixis";
+ reg = <0x2 0x0 0x0000100>;
+ };
+};
+
+&lpuart0 {
+ status = "okay";
+};
+
+&qspi {
+ num-cs = <2>;
+ bus-num = <0>;
+ status = "okay";
+
+ qflash0: s25fl128s at 0 {
+ compatible = "spansion,m25p80";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 22+ messages in thread