* [PATCH 0/1] input: touchscreen: Remove duplicate ft6236 driver
@ 2016-08-05 7:24 ` Hans de Goede
0 siblings, 0 replies; 14+ messages in thread
From: Hans de Goede @ 2016-08-05 7:24 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-input, linux-arm-kernel, devicetree, Noralf Trønnes
<resend with Noralf's email address fixed>
Hi All,
December 19th 2015 I noticed that a new ft6236 driver had been added to
the kernel, and that it was in essence just a re-implementation of the
M09 protocol from the edt-ft5x06 driver, IOW it contains 100% duplicate
code. I asked the submitter and authors of the new ft6236 driver to test
there devices with the edt-ft5x06 driver instead, but I got no reply.
January 26th 2016 I asked the submitter and authors of the new ft6236
driver to test with the edt-ft5x06 driver again, but again got no reply.
Note: this is likely due to my having made an error in Noralf's email
address with those 2 mails (sorry), so it would be good to give Noralf
some time to reply now before applying this.
Given the lack of response from the submitter / authors of the ft6236
driver I believe it is best to just remove it. I've double checked and
the edt-ft5x06 driver is 100% compatible both wrt wire protocol usage,
as wrt to the reset gpio usage (and the gpio name in dt).
Regards,
Hans
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 0/1] input: touchscreen: Remove duplicate ft6236 driver
@ 2016-08-05 7:24 ` Hans de Goede
0 siblings, 0 replies; 14+ messages in thread
From: Hans de Goede @ 2016-08-05 7:24 UTC (permalink / raw)
To: linux-arm-kernel
<resend with Noralf's email address fixed>
Hi All,
December 19th 2015 I noticed that a new ft6236 driver had been added to
the kernel, and that it was in essence just a re-implementation of the
M09 protocol from the edt-ft5x06 driver, IOW it contains 100% duplicate
code. I asked the submitter and authors of the new ft6236 driver to test
there devices with the edt-ft5x06 driver instead, but I got no reply.
January 26th 2016 I asked the submitter and authors of the new ft6236
driver to test with the edt-ft5x06 driver again, but again got no reply.
Note: this is likely due to my having made an error in Noralf's email
address with those 2 mails (sorry), so it would be good to give Noralf
some time to reply now before applying this.
Given the lack of response from the submitter / authors of the ft6236
driver I believe it is best to just remove it. I've double checked and
the edt-ft5x06 driver is 100% compatible both wrt wire protocol usage,
as wrt to the reset gpio usage (and the gpio name in dt).
Regards,
Hans
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
2016-08-05 7:24 ` Hans de Goede
@ 2016-08-05 7:24 ` Hans de Goede
-1 siblings, 0 replies; 14+ messages in thread
From: Hans de Goede @ 2016-08-05 7:24 UTC (permalink / raw)
To: Dmitry Torokhov
Cc: linux-input, linux-arm-kernel, devicetree, Noralf Trønnes,
Hans de Goede, Sean Cross
The new(ish) ft6236 simply re-implements the M09 protocol of the
(much) older edt-ft5x06.c driver.
This commit removes this duplicate driver and adds the i2c ids and
dt compatible string to the edt-ft5x06.c driver to keep compatibility.
Cc: Sean Cross <xobs@kosagi.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
drivers/input/touchscreen/Kconfig | 13 --
drivers/input/touchscreen/Makefile | 1 -
drivers/input/touchscreen/edt-ft5x06.c | 8 +
drivers/input/touchscreen/ft6236.c | 326 ---------------------------------
4 files changed, 8 insertions(+), 340 deletions(-)
delete mode 100644 drivers/input/touchscreen/ft6236.c
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 64e7501..198945d 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -305,19 +305,6 @@ config TOUCHSCREEN_EGALAX_SERIAL
To compile this driver as a module, choose M here: the
module will be called egalax_ts_serial.
-config TOUCHSCREEN_FT6236
- tristate "FT6236 I2C touchscreen"
- depends on I2C
- depends on GPIOLIB || COMPILE_TEST
- help
- Say Y here to enable support for the I2C connected FT6x06 and
- FT6x36 family of capacitive touchscreen drivers.
-
- If unsure, say N.
-
- To compile this driver as a module, choose M here: the
- module will be called ft6236.
-
config TOUCHSCREEN_FUJITSU
tristate "Fujitsu serial touchscreen"
select SERIO
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index a4b00d0..a144c4e 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -36,7 +36,6 @@ obj-$(CONFIG_TOUCHSCREEN_ELAN) += elants_i2c.o
obj-$(CONFIG_TOUCHSCREEN_ELO) += elo.o
obj-$(CONFIG_TOUCHSCREEN_EGALAX) += egalax_ts.o
obj-$(CONFIG_TOUCHSCREEN_EGALAX_SERIAL) += egalax_ts_serial.o
-obj-$(CONFIG_TOUCHSCREEN_FT6236) += ft6236.o
obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o
obj-$(CONFIG_TOUCHSCREEN_GOODIX) += goodix.o
obj-$(CONFIG_TOUCHSCREEN_ILI210X) += ili210x.o
diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index d19bf45..481d8ba 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -1071,9 +1071,15 @@ static const struct edt_i2c_chip_data edt_ft5506_data = {
.max_support_points = 10,
};
+static const struct edt_i2c_chip_data edt_ft6236_data = {
+ .max_support_points = 2,
+};
+
static const struct i2c_device_id edt_ft5x06_ts_id[] = {
{ .name = "edt-ft5x06", .driver_data = (long)&edt_ft5x06_data },
{ .name = "edt-ft5506", .driver_data = (long)&edt_ft5506_data },
+ /* Note no edt- prefix for compatibility with the ft6236.c driver */
+ { .name = "ft6236", .driver_data = (long)&edt_ft6236_data },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(i2c, edt_ft5x06_ts_id);
@@ -1084,6 +1090,8 @@ static const struct of_device_id edt_ft5x06_of_match[] = {
{ .compatible = "edt,edt-ft5306", .data = &edt_ft5x06_data },
{ .compatible = "edt,edt-ft5406", .data = &edt_ft5x06_data },
{ .compatible = "edt,edt-ft5506", .data = &edt_ft5506_data },
+ /* Note focaltech vendor prefix for compatibility with ft6236.c */
+ { .compatible = "focaltech,ft6236", .data = &edt_ft6236_data },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, edt_ft5x06_of_match);
diff --git a/drivers/input/touchscreen/ft6236.c b/drivers/input/touchscreen/ft6236.c
deleted file mode 100644
index d240d2e..0000000
--- a/drivers/input/touchscreen/ft6236.c
+++ /dev/null
@@ -1,326 +0,0 @@
-/*
- * FocalTech FT6236 TouchScreen driver.
- *
- * Copyright (c) 2010 Focal tech Ltd.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio/consumer.h>
-#include <linux/i2c.h>
-#include <linux/input.h>
-#include <linux/input/mt.h>
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/property.h>
-
-#define FT6236_MAX_TOUCH_POINTS 2
-
-#define FT6236_REG_TH_GROUP 0x80
-#define FT6236_REG_PERIODACTIVE 0x88
-#define FT6236_REG_LIB_VER_H 0xa1
-#define FT6236_REG_LIB_VER_L 0xa2
-#define FT6236_REG_CIPHER 0xa3
-#define FT6236_REG_FIRMID 0xa6
-#define FT6236_REG_FOCALTECH_ID 0xa8
-#define FT6236_REG_RELEASE_CODE_ID 0xaf
-
-#define FT6236_EVENT_PRESS_DOWN 0
-#define FT6236_EVENT_LIFT_UP 1
-#define FT6236_EVENT_CONTACT 2
-#define FT6236_EVENT_NO_EVENT 3
-
-struct ft6236_data {
- struct i2c_client *client;
- struct input_dev *input;
- struct gpio_desc *reset_gpio;
- u32 max_x;
- u32 max_y;
- bool invert_x;
- bool invert_y;
- bool swap_xy;
-};
-
-/*
- * This struct is a touchpoint as stored in hardware. Note that the id,
- * as well as the event, are stored in the upper nybble of the hi byte.
- */
-struct ft6236_touchpoint {
- union {
- u8 xhi;
- u8 event;
- };
- u8 xlo;
- union {
- u8 yhi;
- u8 id;
- };
- u8 ylo;
- u8 weight;
- u8 misc;
-} __packed;
-
-/* This packet represents the register map as read from offset 0 */
-struct ft6236_packet {
- u8 dev_mode;
- u8 gest_id;
- u8 touches;
- struct ft6236_touchpoint points[FT6236_MAX_TOUCH_POINTS];
-} __packed;
-
-static int ft6236_read(struct i2c_client *client, u8 reg, u8 len, void *data)
-{
- int error;
-
- error = i2c_smbus_read_i2c_block_data(client, reg, len, data);
- if (error < 0)
- return error;
-
- if (error != len)
- return -EIO;
-
- return 0;
-}
-
-static irqreturn_t ft6236_interrupt(int irq, void *dev_id)
-{
- struct ft6236_data *ft6236 = dev_id;
- struct device *dev = &ft6236->client->dev;
- struct input_dev *input = ft6236->input;
- struct ft6236_packet buf;
- u8 touches;
- int i, error;
-
- error = ft6236_read(ft6236->client, 0, sizeof(buf), &buf);
- if (error) {
- dev_err(dev, "read touchdata failed %d\n", error);
- return IRQ_HANDLED;
- }
-
- touches = buf.touches & 0xf;
- if (touches > FT6236_MAX_TOUCH_POINTS) {
- dev_dbg(dev,
- "%d touch points reported, only %d are supported\n",
- touches, FT6236_MAX_TOUCH_POINTS);
- touches = FT6236_MAX_TOUCH_POINTS;
- }
-
- for (i = 0; i < touches; i++) {
- struct ft6236_touchpoint *point = &buf.points[i];
- u16 x = ((point->xhi & 0xf) << 8) | buf.points[i].xlo;
- u16 y = ((point->yhi & 0xf) << 8) | buf.points[i].ylo;
- u8 event = point->event >> 6;
- u8 id = point->id >> 4;
- bool act = (event == FT6236_EVENT_PRESS_DOWN ||
- event == FT6236_EVENT_CONTACT);
-
- input_mt_slot(input, id);
- input_mt_report_slot_state(input, MT_TOOL_FINGER, act);
- if (!act)
- continue;
-
- if (ft6236->invert_x)
- x = ft6236->max_x - x;
-
- if (ft6236->invert_y)
- y = ft6236->max_y - y;
-
- if (ft6236->swap_xy) {
- input_report_abs(input, ABS_MT_POSITION_X, y);
- input_report_abs(input, ABS_MT_POSITION_Y, x);
- } else {
- input_report_abs(input, ABS_MT_POSITION_X, x);
- input_report_abs(input, ABS_MT_POSITION_Y, y);
- }
- }
-
- input_mt_sync_frame(input);
- input_sync(input);
-
- return IRQ_HANDLED;
-}
-
-static u8 ft6236_debug_read_byte(struct ft6236_data *ft6236, u8 reg)
-{
- struct i2c_client *client = ft6236->client;
- u8 val = 0;
- int error;
-
- error = ft6236_read(client, reg, 1, &val);
- if (error)
- dev_dbg(&client->dev,
- "error reading register 0x%02x: %d\n", reg, error);
-
- return val;
-}
-
-static void ft6236_debug_info(struct ft6236_data *ft6236)
-{
- struct device *dev = &ft6236->client->dev;
-
- dev_dbg(dev, "Touch threshold is %d\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_TH_GROUP) * 4);
- dev_dbg(dev, "Report rate is %dHz\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_PERIODACTIVE) * 10);
- dev_dbg(dev, "Firmware library version 0x%02x%02x\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_LIB_VER_H),
- ft6236_debug_read_byte(ft6236, FT6236_REG_LIB_VER_L));
- dev_dbg(dev, "Firmware version 0x%02x\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_FIRMID));
- dev_dbg(dev, "Chip vendor ID 0x%02x\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_CIPHER));
- dev_dbg(dev, "CTPM vendor ID 0x%02x\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_FOCALTECH_ID));
- dev_dbg(dev, "Release code version 0x%02x\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_RELEASE_CODE_ID));
-}
-
-static void ft6236_reset(struct ft6236_data *ft6236)
-{
- if (!ft6236->reset_gpio)
- return;
-
- gpiod_set_value_cansleep(ft6236->reset_gpio, 1);
- usleep_range(5000, 20000);
- gpiod_set_value_cansleep(ft6236->reset_gpio, 0);
- msleep(300);
-}
-
-static int ft6236_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
-{
- struct device *dev = &client->dev;
- struct ft6236_data *ft6236;
- struct input_dev *input;
- u32 fuzz_x = 0, fuzz_y = 0;
- u8 val;
- int error;
-
- if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
- return -ENXIO;
-
- if (!client->irq) {
- dev_err(dev, "irq is missing\n");
- return -EINVAL;
- }
-
- ft6236 = devm_kzalloc(dev, sizeof(*ft6236), GFP_KERNEL);
- if (!ft6236)
- return -ENOMEM;
-
- ft6236->client = client;
- ft6236->reset_gpio = devm_gpiod_get_optional(dev, "reset",
- GPIOD_OUT_LOW);
- if (IS_ERR(ft6236->reset_gpio)) {
- error = PTR_ERR(ft6236->reset_gpio);
- if (error != -EPROBE_DEFER)
- dev_err(dev, "error getting reset gpio: %d\n", error);
- return error;
- }
-
- ft6236_reset(ft6236);
-
- /* verify that the controller is present */
- error = ft6236_read(client, 0x00, 1, &val);
- if (error) {
- dev_err(dev, "failed to read from controller: %d\n", error);
- return error;
- }
-
- ft6236_debug_info(ft6236);
-
- input = devm_input_allocate_device(dev);
- if (!input)
- return -ENOMEM;
-
- ft6236->input = input;
- input->name = client->name;
- input->id.bustype = BUS_I2C;
-
- if (device_property_read_u32(dev, "touchscreen-size-x",
- &ft6236->max_x) ||
- device_property_read_u32(dev, "touchscreen-size-y",
- &ft6236->max_y)) {
- dev_err(dev, "touchscreen-size-x and/or -y missing\n");
- return -EINVAL;
- }
-
- device_property_read_u32(dev, "touchscreen-fuzz-x", &fuzz_x);
- device_property_read_u32(dev, "touchscreen-fuzz-y", &fuzz_y);
- ft6236->invert_x = device_property_read_bool(dev,
- "touchscreen-inverted-x");
- ft6236->invert_y = device_property_read_bool(dev,
- "touchscreen-inverted-y");
- ft6236->swap_xy = device_property_read_bool(dev,
- "touchscreen-swapped-x-y");
-
- if (ft6236->swap_xy) {
- input_set_abs_params(input, ABS_MT_POSITION_X, 0,
- ft6236->max_y, fuzz_y, 0);
- input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
- ft6236->max_x, fuzz_x, 0);
- } else {
- input_set_abs_params(input, ABS_MT_POSITION_X, 0,
- ft6236->max_x, fuzz_x, 0);
- input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
- ft6236->max_y, fuzz_y, 0);
- }
-
- error = input_mt_init_slots(input, FT6236_MAX_TOUCH_POINTS,
- INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
- if (error)
- return error;
-
- error = devm_request_threaded_irq(dev, client->irq, NULL,
- ft6236_interrupt, IRQF_ONESHOT,
- client->name, ft6236);
- if (error) {
- dev_err(dev, "request irq %d failed: %d\n", client->irq, error);
- return error;
- }
-
- error = input_register_device(input);
- if (error) {
- dev_err(dev, "failed to register input device: %d\n", error);
- return error;
- }
-
- return 0;
-}
-
-#ifdef CONFIG_OF
-static const struct of_device_id ft6236_of_match[] = {
- { .compatible = "focaltech,ft6236", },
- { }
-};
-MODULE_DEVICE_TABLE(of, ft6236_of_match);
-#endif
-
-static const struct i2c_device_id ft6236_id[] = {
- { "ft6236", },
- { }
-};
-MODULE_DEVICE_TABLE(i2c, ft6236_id);
-
-static struct i2c_driver ft6236_driver = {
- .driver = {
- .name = "ft6236",
- .of_match_table = of_match_ptr(ft6236_of_match),
- },
- .probe = ft6236_probe,
- .id_table = ft6236_id,
-};
-module_i2c_driver(ft6236_driver);
-
-MODULE_AUTHOR("Sean Cross <xobs@kosagi.com>");
-MODULE_AUTHOR("Noralf Trønnes <noralf@tronnes.org>");
-MODULE_DESCRIPTION("FocalTech FT6236 TouchScreen driver");
-MODULE_LICENSE("GPL v2");
--
2.7.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
@ 2016-08-05 7:24 ` Hans de Goede
0 siblings, 0 replies; 14+ messages in thread
From: Hans de Goede @ 2016-08-05 7:24 UTC (permalink / raw)
To: linux-arm-kernel
The new(ish) ft6236 simply re-implements the M09 protocol of the
(much) older edt-ft5x06.c driver.
This commit removes this duplicate driver and adds the i2c ids and
dt compatible string to the edt-ft5x06.c driver to keep compatibility.
Cc: Sean Cross <xobs@kosagi.com>
Cc: Noralf Tr?nnes <noralf@tronnes.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
drivers/input/touchscreen/Kconfig | 13 --
drivers/input/touchscreen/Makefile | 1 -
drivers/input/touchscreen/edt-ft5x06.c | 8 +
drivers/input/touchscreen/ft6236.c | 326 ---------------------------------
4 files changed, 8 insertions(+), 340 deletions(-)
delete mode 100644 drivers/input/touchscreen/ft6236.c
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 64e7501..198945d 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -305,19 +305,6 @@ config TOUCHSCREEN_EGALAX_SERIAL
To compile this driver as a module, choose M here: the
module will be called egalax_ts_serial.
-config TOUCHSCREEN_FT6236
- tristate "FT6236 I2C touchscreen"
- depends on I2C
- depends on GPIOLIB || COMPILE_TEST
- help
- Say Y here to enable support for the I2C connected FT6x06 and
- FT6x36 family of capacitive touchscreen drivers.
-
- If unsure, say N.
-
- To compile this driver as a module, choose M here: the
- module will be called ft6236.
-
config TOUCHSCREEN_FUJITSU
tristate "Fujitsu serial touchscreen"
select SERIO
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index a4b00d0..a144c4e 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -36,7 +36,6 @@ obj-$(CONFIG_TOUCHSCREEN_ELAN) += elants_i2c.o
obj-$(CONFIG_TOUCHSCREEN_ELO) += elo.o
obj-$(CONFIG_TOUCHSCREEN_EGALAX) += egalax_ts.o
obj-$(CONFIG_TOUCHSCREEN_EGALAX_SERIAL) += egalax_ts_serial.o
-obj-$(CONFIG_TOUCHSCREEN_FT6236) += ft6236.o
obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o
obj-$(CONFIG_TOUCHSCREEN_GOODIX) += goodix.o
obj-$(CONFIG_TOUCHSCREEN_ILI210X) += ili210x.o
diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index d19bf45..481d8ba 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -1071,9 +1071,15 @@ static const struct edt_i2c_chip_data edt_ft5506_data = {
.max_support_points = 10,
};
+static const struct edt_i2c_chip_data edt_ft6236_data = {
+ .max_support_points = 2,
+};
+
static const struct i2c_device_id edt_ft5x06_ts_id[] = {
{ .name = "edt-ft5x06", .driver_data = (long)&edt_ft5x06_data },
{ .name = "edt-ft5506", .driver_data = (long)&edt_ft5506_data },
+ /* Note no edt- prefix for compatibility with the ft6236.c driver */
+ { .name = "ft6236", .driver_data = (long)&edt_ft6236_data },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(i2c, edt_ft5x06_ts_id);
@@ -1084,6 +1090,8 @@ static const struct of_device_id edt_ft5x06_of_match[] = {
{ .compatible = "edt,edt-ft5306", .data = &edt_ft5x06_data },
{ .compatible = "edt,edt-ft5406", .data = &edt_ft5x06_data },
{ .compatible = "edt,edt-ft5506", .data = &edt_ft5506_data },
+ /* Note focaltech vendor prefix for compatibility with ft6236.c */
+ { .compatible = "focaltech,ft6236", .data = &edt_ft6236_data },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, edt_ft5x06_of_match);
diff --git a/drivers/input/touchscreen/ft6236.c b/drivers/input/touchscreen/ft6236.c
deleted file mode 100644
index d240d2e..0000000
--- a/drivers/input/touchscreen/ft6236.c
+++ /dev/null
@@ -1,326 +0,0 @@
-/*
- * FocalTech FT6236 TouchScreen driver.
- *
- * Copyright (c) 2010 Focal tech Ltd.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/delay.h>
-#include <linux/gpio/consumer.h>
-#include <linux/i2c.h>
-#include <linux/input.h>
-#include <linux/input/mt.h>
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/property.h>
-
-#define FT6236_MAX_TOUCH_POINTS 2
-
-#define FT6236_REG_TH_GROUP 0x80
-#define FT6236_REG_PERIODACTIVE 0x88
-#define FT6236_REG_LIB_VER_H 0xa1
-#define FT6236_REG_LIB_VER_L 0xa2
-#define FT6236_REG_CIPHER 0xa3
-#define FT6236_REG_FIRMID 0xa6
-#define FT6236_REG_FOCALTECH_ID 0xa8
-#define FT6236_REG_RELEASE_CODE_ID 0xaf
-
-#define FT6236_EVENT_PRESS_DOWN 0
-#define FT6236_EVENT_LIFT_UP 1
-#define FT6236_EVENT_CONTACT 2
-#define FT6236_EVENT_NO_EVENT 3
-
-struct ft6236_data {
- struct i2c_client *client;
- struct input_dev *input;
- struct gpio_desc *reset_gpio;
- u32 max_x;
- u32 max_y;
- bool invert_x;
- bool invert_y;
- bool swap_xy;
-};
-
-/*
- * This struct is a touchpoint as stored in hardware. Note that the id,
- * as well as the event, are stored in the upper nybble of the hi byte.
- */
-struct ft6236_touchpoint {
- union {
- u8 xhi;
- u8 event;
- };
- u8 xlo;
- union {
- u8 yhi;
- u8 id;
- };
- u8 ylo;
- u8 weight;
- u8 misc;
-} __packed;
-
-/* This packet represents the register map as read from offset 0 */
-struct ft6236_packet {
- u8 dev_mode;
- u8 gest_id;
- u8 touches;
- struct ft6236_touchpoint points[FT6236_MAX_TOUCH_POINTS];
-} __packed;
-
-static int ft6236_read(struct i2c_client *client, u8 reg, u8 len, void *data)
-{
- int error;
-
- error = i2c_smbus_read_i2c_block_data(client, reg, len, data);
- if (error < 0)
- return error;
-
- if (error != len)
- return -EIO;
-
- return 0;
-}
-
-static irqreturn_t ft6236_interrupt(int irq, void *dev_id)
-{
- struct ft6236_data *ft6236 = dev_id;
- struct device *dev = &ft6236->client->dev;
- struct input_dev *input = ft6236->input;
- struct ft6236_packet buf;
- u8 touches;
- int i, error;
-
- error = ft6236_read(ft6236->client, 0, sizeof(buf), &buf);
- if (error) {
- dev_err(dev, "read touchdata failed %d\n", error);
- return IRQ_HANDLED;
- }
-
- touches = buf.touches & 0xf;
- if (touches > FT6236_MAX_TOUCH_POINTS) {
- dev_dbg(dev,
- "%d touch points reported, only %d are supported\n",
- touches, FT6236_MAX_TOUCH_POINTS);
- touches = FT6236_MAX_TOUCH_POINTS;
- }
-
- for (i = 0; i < touches; i++) {
- struct ft6236_touchpoint *point = &buf.points[i];
- u16 x = ((point->xhi & 0xf) << 8) | buf.points[i].xlo;
- u16 y = ((point->yhi & 0xf) << 8) | buf.points[i].ylo;
- u8 event = point->event >> 6;
- u8 id = point->id >> 4;
- bool act = (event == FT6236_EVENT_PRESS_DOWN ||
- event == FT6236_EVENT_CONTACT);
-
- input_mt_slot(input, id);
- input_mt_report_slot_state(input, MT_TOOL_FINGER, act);
- if (!act)
- continue;
-
- if (ft6236->invert_x)
- x = ft6236->max_x - x;
-
- if (ft6236->invert_y)
- y = ft6236->max_y - y;
-
- if (ft6236->swap_xy) {
- input_report_abs(input, ABS_MT_POSITION_X, y);
- input_report_abs(input, ABS_MT_POSITION_Y, x);
- } else {
- input_report_abs(input, ABS_MT_POSITION_X, x);
- input_report_abs(input, ABS_MT_POSITION_Y, y);
- }
- }
-
- input_mt_sync_frame(input);
- input_sync(input);
-
- return IRQ_HANDLED;
-}
-
-static u8 ft6236_debug_read_byte(struct ft6236_data *ft6236, u8 reg)
-{
- struct i2c_client *client = ft6236->client;
- u8 val = 0;
- int error;
-
- error = ft6236_read(client, reg, 1, &val);
- if (error)
- dev_dbg(&client->dev,
- "error reading register 0x%02x: %d\n", reg, error);
-
- return val;
-}
-
-static void ft6236_debug_info(struct ft6236_data *ft6236)
-{
- struct device *dev = &ft6236->client->dev;
-
- dev_dbg(dev, "Touch threshold is %d\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_TH_GROUP) * 4);
- dev_dbg(dev, "Report rate is %dHz\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_PERIODACTIVE) * 10);
- dev_dbg(dev, "Firmware library version 0x%02x%02x\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_LIB_VER_H),
- ft6236_debug_read_byte(ft6236, FT6236_REG_LIB_VER_L));
- dev_dbg(dev, "Firmware version 0x%02x\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_FIRMID));
- dev_dbg(dev, "Chip vendor ID 0x%02x\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_CIPHER));
- dev_dbg(dev, "CTPM vendor ID 0x%02x\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_FOCALTECH_ID));
- dev_dbg(dev, "Release code version 0x%02x\n",
- ft6236_debug_read_byte(ft6236, FT6236_REG_RELEASE_CODE_ID));
-}
-
-static void ft6236_reset(struct ft6236_data *ft6236)
-{
- if (!ft6236->reset_gpio)
- return;
-
- gpiod_set_value_cansleep(ft6236->reset_gpio, 1);
- usleep_range(5000, 20000);
- gpiod_set_value_cansleep(ft6236->reset_gpio, 0);
- msleep(300);
-}
-
-static int ft6236_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
-{
- struct device *dev = &client->dev;
- struct ft6236_data *ft6236;
- struct input_dev *input;
- u32 fuzz_x = 0, fuzz_y = 0;
- u8 val;
- int error;
-
- if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
- return -ENXIO;
-
- if (!client->irq) {
- dev_err(dev, "irq is missing\n");
- return -EINVAL;
- }
-
- ft6236 = devm_kzalloc(dev, sizeof(*ft6236), GFP_KERNEL);
- if (!ft6236)
- return -ENOMEM;
-
- ft6236->client = client;
- ft6236->reset_gpio = devm_gpiod_get_optional(dev, "reset",
- GPIOD_OUT_LOW);
- if (IS_ERR(ft6236->reset_gpio)) {
- error = PTR_ERR(ft6236->reset_gpio);
- if (error != -EPROBE_DEFER)
- dev_err(dev, "error getting reset gpio: %d\n", error);
- return error;
- }
-
- ft6236_reset(ft6236);
-
- /* verify that the controller is present */
- error = ft6236_read(client, 0x00, 1, &val);
- if (error) {
- dev_err(dev, "failed to read from controller: %d\n", error);
- return error;
- }
-
- ft6236_debug_info(ft6236);
-
- input = devm_input_allocate_device(dev);
- if (!input)
- return -ENOMEM;
-
- ft6236->input = input;
- input->name = client->name;
- input->id.bustype = BUS_I2C;
-
- if (device_property_read_u32(dev, "touchscreen-size-x",
- &ft6236->max_x) ||
- device_property_read_u32(dev, "touchscreen-size-y",
- &ft6236->max_y)) {
- dev_err(dev, "touchscreen-size-x and/or -y missing\n");
- return -EINVAL;
- }
-
- device_property_read_u32(dev, "touchscreen-fuzz-x", &fuzz_x);
- device_property_read_u32(dev, "touchscreen-fuzz-y", &fuzz_y);
- ft6236->invert_x = device_property_read_bool(dev,
- "touchscreen-inverted-x");
- ft6236->invert_y = device_property_read_bool(dev,
- "touchscreen-inverted-y");
- ft6236->swap_xy = device_property_read_bool(dev,
- "touchscreen-swapped-x-y");
-
- if (ft6236->swap_xy) {
- input_set_abs_params(input, ABS_MT_POSITION_X, 0,
- ft6236->max_y, fuzz_y, 0);
- input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
- ft6236->max_x, fuzz_x, 0);
- } else {
- input_set_abs_params(input, ABS_MT_POSITION_X, 0,
- ft6236->max_x, fuzz_x, 0);
- input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
- ft6236->max_y, fuzz_y, 0);
- }
-
- error = input_mt_init_slots(input, FT6236_MAX_TOUCH_POINTS,
- INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
- if (error)
- return error;
-
- error = devm_request_threaded_irq(dev, client->irq, NULL,
- ft6236_interrupt, IRQF_ONESHOT,
- client->name, ft6236);
- if (error) {
- dev_err(dev, "request irq %d failed: %d\n", client->irq, error);
- return error;
- }
-
- error = input_register_device(input);
- if (error) {
- dev_err(dev, "failed to register input device: %d\n", error);
- return error;
- }
-
- return 0;
-}
-
-#ifdef CONFIG_OF
-static const struct of_device_id ft6236_of_match[] = {
- { .compatible = "focaltech,ft6236", },
- { }
-};
-MODULE_DEVICE_TABLE(of, ft6236_of_match);
-#endif
-
-static const struct i2c_device_id ft6236_id[] = {
- { "ft6236", },
- { }
-};
-MODULE_DEVICE_TABLE(i2c, ft6236_id);
-
-static struct i2c_driver ft6236_driver = {
- .driver = {
- .name = "ft6236",
- .of_match_table = of_match_ptr(ft6236_of_match),
- },
- .probe = ft6236_probe,
- .id_table = ft6236_id,
-};
-module_i2c_driver(ft6236_driver);
-
-MODULE_AUTHOR("Sean Cross <xobs@kosagi.com>");
-MODULE_AUTHOR("Noralf Tr?nnes <noralf@tronnes.org>");
-MODULE_DESCRIPTION("FocalTech FT6236 TouchScreen driver");
-MODULE_LICENSE("GPL v2");
--
2.7.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
2016-08-05 7:24 ` Hans de Goede
@ 2016-08-05 15:07 ` Stefan Wahren
-1 siblings, 0 replies; 14+ messages in thread
From: Stefan Wahren @ 2016-08-05 15:07 UTC (permalink / raw)
To: Hans de Goede, Dmitry Torokhov
Cc: devicetree, Noralf Trønnes,
linux-input-u79uwXL29TY76Z2rM5mHXA, Sean Cross,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hi Hans,
Am 05.08.2016 um 09:24 schrieb Hans de Goede:
> The new(ish) ft6236 simply re-implements the M09 protocol of the
> (much) older edt-ft5x06.c driver.
>
> This commit removes this duplicate driver and adds the i2c ids and
> dt compatible string to the edt-ft5x06.c driver to keep compatibility.
i think only remove of the driver is incorrect here.
Since there are two similar but still different DT bindings
Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
the DT handling of edt-ft5x06.c needs to be extended and then finally
driver and binding could be removed.
Regards
Stefan
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
@ 2016-08-05 15:07 ` Stefan Wahren
0 siblings, 0 replies; 14+ messages in thread
From: Stefan Wahren @ 2016-08-05 15:07 UTC (permalink / raw)
To: linux-arm-kernel
Hi Hans,
Am 05.08.2016 um 09:24 schrieb Hans de Goede:
> The new(ish) ft6236 simply re-implements the M09 protocol of the
> (much) older edt-ft5x06.c driver.
>
> This commit removes this duplicate driver and adds the i2c ids and
> dt compatible string to the edt-ft5x06.c driver to keep compatibility.
i think only remove of the driver is incorrect here.
Since there are two similar but still different DT bindings
Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
the DT handling of edt-ft5x06.c needs to be extended and then finally
driver and binding could be removed.
Regards
Stefan
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
2016-08-05 15:07 ` Stefan Wahren
@ 2016-08-06 2:22 ` Dmitry Torokhov
-1 siblings, 0 replies; 14+ messages in thread
From: Dmitry Torokhov @ 2016-08-06 2:22 UTC (permalink / raw)
To: Stefan Wahren
Cc: devicetree, Hans de Goede, Noralf Trønnes, linux-input,
Sean Cross, linux-arm-kernel
On Fri, Aug 05, 2016 at 05:07:20PM +0200, Stefan Wahren wrote:
> Hi Hans,
>
> Am 05.08.2016 um 09:24 schrieb Hans de Goede:
> >The new(ish) ft6236 simply re-implements the M09 protocol of the
> >(much) older edt-ft5x06.c driver.
> >
> >This commit removes this duplicate driver and adds the i2c ids and
> >dt compatible string to the edt-ft5x06.c driver to keep compatibility.
>
> i think only remove of the driver is incorrect here.
>
> Since there are two similar but still different DT bindings
>
> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
>
> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
>
> the DT handling of edt-ft5x06.c needs to be extended and then
> finally driver and binding could be removed.
I believe Hans made sure edt-ft5x06.c can handle focaltech-ft6236
bindings. Do you see a discrepancy?
Thanks.
--
Dmitry
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
@ 2016-08-06 2:22 ` Dmitry Torokhov
0 siblings, 0 replies; 14+ messages in thread
From: Dmitry Torokhov @ 2016-08-06 2:22 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Aug 05, 2016 at 05:07:20PM +0200, Stefan Wahren wrote:
> Hi Hans,
>
> Am 05.08.2016 um 09:24 schrieb Hans de Goede:
> >The new(ish) ft6236 simply re-implements the M09 protocol of the
> >(much) older edt-ft5x06.c driver.
> >
> >This commit removes this duplicate driver and adds the i2c ids and
> >dt compatible string to the edt-ft5x06.c driver to keep compatibility.
>
> i think only remove of the driver is incorrect here.
>
> Since there are two similar but still different DT bindings
>
> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
>
> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
>
> the DT handling of edt-ft5x06.c needs to be extended and then
> finally driver and binding could be removed.
I believe Hans made sure edt-ft5x06.c can handle focaltech-ft6236
bindings. Do you see a discrepancy?
Thanks.
--
Dmitry
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
2016-08-06 2:22 ` Dmitry Torokhov
@ 2016-08-06 10:00 ` Hans de Goede
-1 siblings, 0 replies; 14+ messages in thread
From: Hans de Goede @ 2016-08-06 10:00 UTC (permalink / raw)
To: Dmitry Torokhov, Stefan Wahren
Cc: devicetree, Sean Cross, noralf, linux-arm-kernel, linux-input
Hi,
On 06-08-16 04:22, Dmitry Torokhov wrote:
> On Fri, Aug 05, 2016 at 05:07:20PM +0200, Stefan Wahren wrote:
>> Hi Hans,
>>
>> Am 05.08.2016 um 09:24 schrieb Hans de Goede:
>>> The new(ish) ft6236 simply re-implements the M09 protocol of the
>>> (much) older edt-ft5x06.c driver.
>>>
>>> This commit removes this duplicate driver and adds the i2c ids and
>>> dt compatible string to the edt-ft5x06.c driver to keep compatibility.
>>
>> i think only remove of the driver is incorrect here.
>>
>> Since there are two similar but still different DT bindings
>>
>> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
>>
>> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
>>
>> the DT handling of edt-ft5x06.c needs to be extended and then
>> finally driver and binding could be removed.
>
> I believe Hans made sure edt-ft5x06.c can handle focaltech-ft6236
> bindings. Do you see a discrepancy?
Correct I've double checked that both the i2c protocol and the
reset gpio binding are compatible. Devices using the focaltech-ft6236.txt
binding should work fine with the edt-ft5x06.c driver.
Now if someone can test and confirm that on actual hardware that would be
great...
And we probably want to remove
Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
and instead add the compatible string that defines to
Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
I can whip up a patch for that, but as said some testing on actual
hw would be good, preferably before I write said patch.
Regards,
Hans
p.s.
(the v3 in the subject is bogus my bad)
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
@ 2016-08-06 10:00 ` Hans de Goede
0 siblings, 0 replies; 14+ messages in thread
From: Hans de Goede @ 2016-08-06 10:00 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
On 06-08-16 04:22, Dmitry Torokhov wrote:
> On Fri, Aug 05, 2016 at 05:07:20PM +0200, Stefan Wahren wrote:
>> Hi Hans,
>>
>> Am 05.08.2016 um 09:24 schrieb Hans de Goede:
>>> The new(ish) ft6236 simply re-implements the M09 protocol of the
>>> (much) older edt-ft5x06.c driver.
>>>
>>> This commit removes this duplicate driver and adds the i2c ids and
>>> dt compatible string to the edt-ft5x06.c driver to keep compatibility.
>>
>> i think only remove of the driver is incorrect here.
>>
>> Since there are two similar but still different DT bindings
>>
>> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
>>
>> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
>>
>> the DT handling of edt-ft5x06.c needs to be extended and then
>> finally driver and binding could be removed.
>
> I believe Hans made sure edt-ft5x06.c can handle focaltech-ft6236
> bindings. Do you see a discrepancy?
Correct I've double checked that both the i2c protocol and the
reset gpio binding are compatible. Devices using the focaltech-ft6236.txt
binding should work fine with the edt-ft5x06.c driver.
Now if someone can test and confirm that on actual hardware that would be
great...
And we probably want to remove
Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
and instead add the compatible string that defines to
Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
I can whip up a patch for that, but as said some testing on actual
hw would be good, preferably before I write said patch.
Regards,
Hans
p.s.
(the v3 in the subject is bogus my bad)
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
2016-08-06 10:00 ` Hans de Goede
@ 2016-08-06 12:43 ` Noralf Trønnes
-1 siblings, 0 replies; 14+ messages in thread
From: Noralf Trønnes @ 2016-08-06 12:43 UTC (permalink / raw)
To: Hans de Goede, Dmitry Torokhov, Stefan Wahren
Cc: devicetree, Sean Cross, linux-arm-kernel, linux-input
Den 06.08.2016 12:00, skrev Hans de Goede:
> Hi,
>
> On 06-08-16 04:22, Dmitry Torokhov wrote:
>> On Fri, Aug 05, 2016 at 05:07:20PM +0200, Stefan Wahren wrote:
>>> Hi Hans,
>>>
>>> Am 05.08.2016 um 09:24 schrieb Hans de Goede:
>>>> The new(ish) ft6236 simply re-implements the M09 protocol of the
>>>> (much) older edt-ft5x06.c driver.
>>>>
>>>> This commit removes this duplicate driver and adds the i2c ids and
>>>> dt compatible string to the edt-ft5x06.c driver to keep compatibility.
>>>
>>> i think only remove of the driver is incorrect here.
>>>
>>> Since there are two similar but still different DT bindings
>>>
>>> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
>>>
>>> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
>>>
>>>
>>> the DT handling of edt-ft5x06.c needs to be extended and then
>>> finally driver and binding could be removed.
>>
>> I believe Hans made sure edt-ft5x06.c can handle focaltech-ft6236
>> bindings. Do you see a discrepancy?
>
> Correct I've double checked that both the i2c protocol and the
> reset gpio binding are compatible. Devices using the focaltech-ft6236.txt
> binding should work fine with the edt-ft5x06.c driver.
>
> Now if someone can test and confirm that on actual hardware that would be
> great...
>
> And we probably want to remove
> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
> and instead add the compatible string that defines to
> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
>
> I can whip up a patch for that, but as said some testing on actual
> hw would be good, preferably before I write said patch.
>
I can confirm that this works with a ft6236.
[ 1.987092] input: EP0110M09 as
/devices/platform/soc/20804000.i2c/i2c-1/1-0038/input/input0
My display panel is broken, but the values reported by evtest looks correct.
Thanks for doing this, one less driver to care about.
Maybe you could add a reference to touchscreen.txt in edt-ft5x06.txt?
Noralf.
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
@ 2016-08-06 12:43 ` Noralf Trønnes
0 siblings, 0 replies; 14+ messages in thread
From: Noralf Trønnes @ 2016-08-06 12:43 UTC (permalink / raw)
To: linux-arm-kernel
Den 06.08.2016 12:00, skrev Hans de Goede:
> Hi,
>
> On 06-08-16 04:22, Dmitry Torokhov wrote:
>> On Fri, Aug 05, 2016 at 05:07:20PM +0200, Stefan Wahren wrote:
>>> Hi Hans,
>>>
>>> Am 05.08.2016 um 09:24 schrieb Hans de Goede:
>>>> The new(ish) ft6236 simply re-implements the M09 protocol of the
>>>> (much) older edt-ft5x06.c driver.
>>>>
>>>> This commit removes this duplicate driver and adds the i2c ids and
>>>> dt compatible string to the edt-ft5x06.c driver to keep compatibility.
>>>
>>> i think only remove of the driver is incorrect here.
>>>
>>> Since there are two similar but still different DT bindings
>>>
>>> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
>>>
>>> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
>>>
>>>
>>> the DT handling of edt-ft5x06.c needs to be extended and then
>>> finally driver and binding could be removed.
>>
>> I believe Hans made sure edt-ft5x06.c can handle focaltech-ft6236
>> bindings. Do you see a discrepancy?
>
> Correct I've double checked that both the i2c protocol and the
> reset gpio binding are compatible. Devices using the focaltech-ft6236.txt
> binding should work fine with the edt-ft5x06.c driver.
>
> Now if someone can test and confirm that on actual hardware that would be
> great...
>
> And we probably want to remove
> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
> and instead add the compatible string that defines to
> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
>
> I can whip up a patch for that, but as said some testing on actual
> hw would be good, preferably before I write said patch.
>
I can confirm that this works with a ft6236.
[ 1.987092] input: EP0110M09 as
/devices/platform/soc/20804000.i2c/i2c-1/1-0038/input/input0
My display panel is broken, but the values reported by evtest looks correct.
Thanks for doing this, one less driver to care about.
Maybe you could add a reference to touchscreen.txt in edt-ft5x06.txt?
Noralf.
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
2016-08-06 10:00 ` Hans de Goede
@ 2016-08-06 13:15 ` Stefan Wahren
-1 siblings, 0 replies; 14+ messages in thread
From: Stefan Wahren @ 2016-08-06 13:15 UTC (permalink / raw)
To: Hans de Goede, Dmitry Torokhov
Cc: devicetree, Sean Cross, Noralf Trønnes, linux-arm-kernel,
linux-input
Hi,
> Hans de Goede <hdegoede@redhat.com> hat am 6. August 2016 um 12:00
> geschrieben:
>
>
> Hi,
>
> On 06-08-16 04:22, Dmitry Torokhov wrote:
> > On Fri, Aug 05, 2016 at 05:07:20PM +0200, Stefan Wahren wrote:
> >> Hi Hans,
> >>
> >> Am 05.08.2016 um 09:24 schrieb Hans de Goede:
> >>> The new(ish) ft6236 simply re-implements the M09 protocol of the
> >>> (much) older edt-ft5x06.c driver.
> >>>
> >>> This commit removes this duplicate driver and adds the i2c ids and
> >>> dt compatible string to the edt-ft5x06.c driver to keep compatibility.
> >>
> >> i think only remove of the driver is incorrect here.
> >>
> >> Since there are two similar but still different DT bindings
> >>
> >> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> >>
> >> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
> >>
> >> the DT handling of edt-ft5x06.c needs to be extended and then
> >> finally driver and binding could be removed.
> >
> > I believe Hans made sure edt-ft5x06.c can handle focaltech-ft6236
> > bindings. Do you see a discrepancy?
>
> Correct I've double checked that both the i2c protocol and the
> reset gpio binding are compatible. Devices using the focaltech-ft6236.txt
> binding should work fine with the edt-ft5x06.c driver.
i missed the point about touchscreen_parse_properties() and it's properties.
Sorry for the noise. Everything okay.
>
> Now if someone can test and confirm that on actual hardware that would be
> great...
>
> And we probably want to remove
> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
> and instead add the compatible string that defines to
> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
>
That would be great.
Stefan
> I can whip up a patch for that, but as said some testing on actual
> hw would be good, preferably before I write said patch.
>
> Regards,
>
> Hans
>
>
>
>
>
> p.s.
>
> (the v3 in the subject is bogus my bad)
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH v3] input: touchscreen: Remove duplicate ft6236 driver
@ 2016-08-06 13:15 ` Stefan Wahren
0 siblings, 0 replies; 14+ messages in thread
From: Stefan Wahren @ 2016-08-06 13:15 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
> Hans de Goede <hdegoede@redhat.com> hat am 6. August 2016 um 12:00
> geschrieben:
>
>
> Hi,
>
> On 06-08-16 04:22, Dmitry Torokhov wrote:
> > On Fri, Aug 05, 2016 at 05:07:20PM +0200, Stefan Wahren wrote:
> >> Hi Hans,
> >>
> >> Am 05.08.2016 um 09:24 schrieb Hans de Goede:
> >>> The new(ish) ft6236 simply re-implements the M09 protocol of the
> >>> (much) older edt-ft5x06.c driver.
> >>>
> >>> This commit removes this duplicate driver and adds the i2c ids and
> >>> dt compatible string to the edt-ft5x06.c driver to keep compatibility.
> >>
> >> i think only remove of the driver is incorrect here.
> >>
> >> Since there are two similar but still different DT bindings
> >>
> >> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
> >>
> >> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
> >>
> >> the DT handling of edt-ft5x06.c needs to be extended and then
> >> finally driver and binding could be removed.
> >
> > I believe Hans made sure edt-ft5x06.c can handle focaltech-ft6236
> > bindings. Do you see a discrepancy?
>
> Correct I've double checked that both the i2c protocol and the
> reset gpio binding are compatible. Devices using the focaltech-ft6236.txt
> binding should work fine with the edt-ft5x06.c driver.
i missed the point about touchscreen_parse_properties() and it's properties.
Sorry for the noise. Everything okay.
>
> Now if someone can test and confirm that on actual hardware that would be
> great...
>
> And we probably want to remove
> Documentation/devicetree/bindings/input/touchscreen/focaltech-ft6236.txt
> and instead add the compatible string that defines to
> Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
>
That would be great.
Stefan
> I can whip up a patch for that, but as said some testing on actual
> hw would be good, preferably before I write said patch.
>
> Regards,
>
> Hans
>
>
>
>
>
> p.s.
>
> (the v3 in the subject is bogus my bad)
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2016-08-06 13:15 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-08-05 7:24 [PATCH 0/1] input: touchscreen: Remove duplicate ft6236 driver Hans de Goede
2016-08-05 7:24 ` Hans de Goede
2016-08-05 7:24 ` [PATCH v3] " Hans de Goede
2016-08-05 7:24 ` Hans de Goede
[not found] ` <1470381871-4086-2-git-send-email-hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
2016-08-05 15:07 ` Stefan Wahren
2016-08-05 15:07 ` Stefan Wahren
2016-08-06 2:22 ` Dmitry Torokhov
2016-08-06 2:22 ` Dmitry Torokhov
2016-08-06 10:00 ` Hans de Goede
2016-08-06 10:00 ` Hans de Goede
2016-08-06 12:43 ` Noralf Trønnes
2016-08-06 12:43 ` Noralf Trønnes
2016-08-06 13:15 ` Stefan Wahren
2016-08-06 13:15 ` Stefan Wahren
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.