From: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> To: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>, Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, devicetree <devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>, Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> Subject: [PATCH v2] ARM: dts: sun8i: Add dts file for the Orange Pi Lite SBC Date: Sun, 7 Aug 2016 16:16:44 +0200 [thread overview] Message-ID: <1470579404-28081-1-git-send-email-hdegoede@redhat.com> (raw) The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM, micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector, sdio attached rtl8189ftv wifi and an ir receiver. Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> --- Changes in v2: -Fix the wifi ethernet alias to be ethernet0 as the comment says, rather then ethernet1 (copy and paste error). --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts | 178 +++++++++++++++++++++++++++ 2 files changed, 179 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 678abe8..3b280f4 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -767,6 +767,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a83t-allwinner-h8homlet-v2.dtb \ sun8i-a83t-cubietruck-plus.dtb \ sun8i-h3-orangepi-2.dtb \ + sun8i-h3-orangepi-lite.dtb \ sun8i-h3-orangepi-one.dtb \ sun8i-h3-orangepi-pc.dtb \ sun8i-h3-orangepi-pc-plus.dtb \ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts new file mode 100644 index 0000000..1550fee --- /dev/null +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts @@ -0,0 +1,178 @@ +/* + * Copyright (C) 2016 Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-h3.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Xunlong Orange Pi Lite"; + compatible = "xunlong,orangepi-lite", "allwinner,sun8i-h3"; + + aliases { + /* The H3 emac is not used so the wifi is ethernet0 */ + ethernet0 = &rtl8189ftv; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&leds_opc>, <&leds_r_opc>; + + pwr_led { + label = "orangepi:green:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + status_led { + label = "orangepi:red:status"; + gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; + }; + }; + + r_gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&sw_r_opc>; + + sw4 { + label = "sw4"; + linux,code = <BTN_0>; + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&ir { + pinctrl-names = "default"; + pinctrl-0 = <&ir_pins_a>; + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + cd-inverted; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + non-removable; + status = "okay"; + + /* + * Explicitly define the sdio device, so that we can add an ethernet + * alias for it (which e.g. makes u-boot set a mac-address). + */ + rtl8189ftv: sdio_wifi@1 { + reg = <1>; + }; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&pio { + leds_opc: led_pins@0 { + allwinner,pins = "PA15"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +&r_pio { + leds_r_opc: led_pins@0 { + allwinner,pins = "PL10"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + sw_r_opc: key_pins@0 { + allwinner,pins = "PL3"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usbphy { + /* USB VBUS is always on */ + status = "okay"; +}; -- 2.7.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: hdegoede@redhat.com (Hans de Goede) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v2] ARM: dts: sun8i: Add dts file for the Orange Pi Lite SBC Date: Sun, 7 Aug 2016 16:16:44 +0200 [thread overview] Message-ID: <1470579404-28081-1-git-send-email-hdegoede@redhat.com> (raw) The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM, micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector, sdio attached rtl8189ftv wifi and an ir receiver. Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- Changes in v2: -Fix the wifi ethernet alias to be ethernet0 as the comment says, rather then ethernet1 (copy and paste error). --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts | 178 +++++++++++++++++++++++++++ 2 files changed, 179 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 678abe8..3b280f4 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -767,6 +767,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-a83t-allwinner-h8homlet-v2.dtb \ sun8i-a83t-cubietruck-plus.dtb \ sun8i-h3-orangepi-2.dtb \ + sun8i-h3-orangepi-lite.dtb \ sun8i-h3-orangepi-one.dtb \ sun8i-h3-orangepi-pc.dtb \ sun8i-h3-orangepi-pc-plus.dtb \ diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts new file mode 100644 index 0000000..1550fee --- /dev/null +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts @@ -0,0 +1,178 @@ +/* + * Copyright (C) 2016 Hans de Goede <hdegoede@redhat.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-h3.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/sun4i-a10.h> + +/ { + model = "Xunlong Orange Pi Lite"; + compatible = "xunlong,orangepi-lite", "allwinner,sun8i-h3"; + + aliases { + /* The H3 emac is not used so the wifi is ethernet0 */ + ethernet0 = &rtl8189ftv; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&leds_opc>, <&leds_r_opc>; + + pwr_led { + label = "orangepi:green:pwr"; + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + status_led { + label = "orangepi:red:status"; + gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; + }; + }; + + r_gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&sw_r_opc>; + + sw4 { + label = "sw4"; + linux,code = <BTN_0>; + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&ehci1 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&ir { + pinctrl-names = "default"; + pinctrl-0 = <&ir_pins_a>; + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ + cd-inverted; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + non-removable; + status = "okay"; + + /* + * Explicitly define the sdio device, so that we can add an ethernet + * alias for it (which e.g. makes u-boot set a mac-address). + */ + rtl8189ftv: sdio_wifi at 1 { + reg = <1>; + }; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&pio { + leds_opc: led_pins at 0 { + allwinner,pins = "PA15"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +&r_pio { + leds_r_opc: led_pins at 0 { + allwinner,pins = "PL10"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; + + sw_r_opc: key_pins at 0 { + allwinner,pins = "PL3"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; +}; + +&usbphy { + /* USB VBUS is always on */ + status = "okay"; +}; -- 2.7.4
next reply other threads:[~2016-08-07 14:16 UTC|newest] Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top 2016-08-07 14:16 Hans de Goede [this message] 2016-08-07 14:16 ` [PATCH v2] ARM: dts: sun8i: Add dts file for the Orange Pi Lite SBC Hans de Goede [not found] ` <1470579404-28081-1-git-send-email-hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> 2016-08-08 4:07 ` Chen-Yu Tsai 2016-08-08 4:07 ` Chen-Yu Tsai 2016-08-22 18:18 ` Maxime Ripard 2016-08-22 18:18 ` Maxime Ripard
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1470579404-28081-1-git-send-email-hdegoede@redhat.com \ --to=hdegoede-h+wxahxf7alqt0dzr+alfa@public.gmane.org \ --cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \ --cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \ --cc=maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org \ --cc=wens-jdAy2FN1RRM@public.gmane.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.