From: Zach Brown <zach.brown@ni.com> To: f.fainelli@gmail.com Cc: mlindner@marvell.com, stephen@networkplumber.org, netdev@vger.kernel.org, linux-kernel@vger.kernel.org, devel@driverdev.osuosl.org, florian.c.schilhabel@googlemail.com, Larry.Finger@lwfinger.net Subject: [RFC 1/3] skge: Change LED_OFF to LED_REG_OFF in marvel skge driver to avoid conflicts with leds namespace Date: Wed, 14 Sep 2016 16:55:47 -0500 [thread overview] Message-ID: <1473890149-2066-2-git-send-email-zach.brown@ni.com> (raw) In-Reply-To: <1473890149-2066-1-git-send-email-zach.brown@ni.com> Adding led support for phy causes namespace conflicts for some phy drivers. The marvel skge driver declared an enum for representing the states of Link LED Register. The enum contained constant LED_OFF which conflicted with declartation found in linux/leds.h. LED_OFF changed to LED_REG_OFF Signed-off-by: Zach Brown <zach.brown@ni.com> --- drivers/net/ethernet/marvell/skge.c | 4 ++-- drivers/net/ethernet/marvell/skge.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/marvell/skge.c b/drivers/net/ethernet/marvell/skge.c index 7173836..ff5a087 100644 --- a/drivers/net/ethernet/marvell/skge.c +++ b/drivers/net/ethernet/marvell/skge.c @@ -1062,7 +1062,7 @@ static void skge_link_up(struct skge_port *skge) static void skge_link_down(struct skge_port *skge) { - skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF); + skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_REG_OFF); netif_carrier_off(skge->netdev); netif_stop_queue(skge->netdev); @@ -2668,7 +2668,7 @@ static int skge_down(struct net_device *dev) if (hw->ports == 1) free_irq(hw->pdev->irq, hw); - skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF); + skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_REG_OFF); if (is_genesis(hw)) genesis_stop(skge); else diff --git a/drivers/net/ethernet/marvell/skge.h b/drivers/net/ethernet/marvell/skge.h index a2eb341..ec054d3 100644 --- a/drivers/net/ethernet/marvell/skge.h +++ b/drivers/net/ethernet/marvell/skge.h @@ -663,7 +663,7 @@ enum { LED_SYNC_ON = 1<<3, /* Use Sync Wire to switch LED */ LED_SYNC_OFF = 1<<2, /* Disable Sync Wire Input */ LED_ON = 1<<1, /* switch LED on */ - LED_OFF = 1<<0, /* switch LED off */ + LED_REG_OFF = 1<<0, /* switch LED off */ }; /* Receive GMAC FIFO (YUKON) */ -- 2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: Zach Brown <zach.brown@ni.com> To: f.fainelli@gmail.com Cc: devel@driverdev.osuosl.org, florian.c.schilhabel@googlemail.com, netdev@vger.kernel.org, linux-kernel@vger.kernel.org, Larry.Finger@lwfinger.net, mlindner@marvell.com Subject: [RFC 1/3] skge: Change LED_OFF to LED_REG_OFF in marvel skge driver to avoid conflicts with leds namespace Date: Wed, 14 Sep 2016 16:55:47 -0500 [thread overview] Message-ID: <1473890149-2066-2-git-send-email-zach.brown@ni.com> (raw) In-Reply-To: <1473890149-2066-1-git-send-email-zach.brown@ni.com> Adding led support for phy causes namespace conflicts for some phy drivers. The marvel skge driver declared an enum for representing the states of Link LED Register. The enum contained constant LED_OFF which conflicted with declartation found in linux/leds.h. LED_OFF changed to LED_REG_OFF Signed-off-by: Zach Brown <zach.brown@ni.com> --- drivers/net/ethernet/marvell/skge.c | 4 ++-- drivers/net/ethernet/marvell/skge.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/marvell/skge.c b/drivers/net/ethernet/marvell/skge.c index 7173836..ff5a087 100644 --- a/drivers/net/ethernet/marvell/skge.c +++ b/drivers/net/ethernet/marvell/skge.c @@ -1062,7 +1062,7 @@ static void skge_link_up(struct skge_port *skge) static void skge_link_down(struct skge_port *skge) { - skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF); + skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_REG_OFF); netif_carrier_off(skge->netdev); netif_stop_queue(skge->netdev); @@ -2668,7 +2668,7 @@ static int skge_down(struct net_device *dev) if (hw->ports == 1) free_irq(hw->pdev->irq, hw); - skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_OFF); + skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_REG_OFF); if (is_genesis(hw)) genesis_stop(skge); else diff --git a/drivers/net/ethernet/marvell/skge.h b/drivers/net/ethernet/marvell/skge.h index a2eb341..ec054d3 100644 --- a/drivers/net/ethernet/marvell/skge.h +++ b/drivers/net/ethernet/marvell/skge.h @@ -663,7 +663,7 @@ enum { LED_SYNC_ON = 1<<3, /* Use Sync Wire to switch LED */ LED_SYNC_OFF = 1<<2, /* Disable Sync Wire Input */ LED_ON = 1<<1, /* switch LED on */ - LED_OFF = 1<<0, /* switch LED off */ + LED_REG_OFF = 1<<0, /* switch LED off */ }; /* Receive GMAC FIFO (YUKON) */ -- 2.7.4
next prev parent reply other threads:[~2016-09-14 21:56 UTC|newest] Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top 2016-09-14 21:55 [RFC 0/3] Add support for led triggers on phy link state change Zach Brown 2016-09-14 21:55 ` Zach Brown 2016-09-14 21:55 ` Zach Brown [this message] 2016-09-14 21:55 ` [RFC 1/3] skge: Change LED_OFF to LED_REG_OFF in marvel skge driver to avoid conflicts with leds namespace Zach Brown 2016-09-14 21:55 ` [RFC 2/3] staging: rtl8712: Change _LED_STATE enum in rtl871x driver to avoid conflicts with LED namespace Zach Brown 2016-09-15 0:13 ` Larry Finger 2016-09-15 0:13 ` Larry Finger 2016-09-14 21:55 ` [RFC 3/3] phy,leds: add support for led triggers on phy link state change Zach Brown 2016-09-14 23:16 ` Florian Fainelli 2016-09-19 15:48 ` Zach Brown 2016-10-07 14:13 ` [RFC 0/3] Add " Pavel Machek 2016-10-07 14:13 ` Pavel Machek
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1473890149-2066-2-git-send-email-zach.brown@ni.com \ --to=zach.brown@ni.com \ --cc=Larry.Finger@lwfinger.net \ --cc=devel@driverdev.osuosl.org \ --cc=f.fainelli@gmail.com \ --cc=florian.c.schilhabel@googlemail.com \ --cc=linux-kernel@vger.kernel.org \ --cc=mlindner@marvell.com \ --cc=netdev@vger.kernel.org \ --cc=stephen@networkplumber.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.