* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
@ 2016-10-08 12:30 Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 01/21] serial: Kconfig: Add MXC_UART entry Jagan Teki
` (21 more replies)
0 siblings, 22 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
and test on the respective starter kits as well.
Tested both MMC and NAND boot.
Changes for v7:
- Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
- Rebase on u-boot-imx/master
Changes for v6:
- Rebase to u-boot-imx/master
- Move few SPL configs to defconfigs
Changes for v5:
- Add NAND support
Changes for v4:
- Add 'net: Kconfig: Add FEC_MXC entry' patch
- Updated ENV configs along with comments
- Restructured configs for more readability
- Add CONFIG_ENV_OVERWRITE
- Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
Changes for v3:
- Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
- Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
- Add minimal devicetree support for Engicam i.CoreM6 QDL
- Add is_mx6dl()
- Add is_mx6solo()
- Use is_mx6dq()
- Add last commit sha1 and header in pull devicetree files from Linux
Changes for v2:
- Make static to local iomux structure in board file
- Corrected rowaddr in mx6_ddr3_cfg
- Used imx_ddr_size
- Add FEC support and tested the same
- Add DM_GPIO, DM_MMC support
- Add pinctrl support
- Add devicetree support
Jagan Teki (21):
serial: Kconfig: Add MXC_UART entry
thermal: Kconfig: Add IMX_THERMAL entry
config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
net: Kconfig: Add FEC_MXC entry
imx6: icorem6: Add ENET support
imx: s/docs\/README.imximage/doc\/README.imximage/g
arm: dts: Add devicetree for i.MX6DL
arm: dts: Add devicetree for i.MX6DQL
arm: dts: imx6dl: Add pinctrl defines
dt-bindings: clock: imx6qdl: Add clock defines
arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
imx6q: icorem6: Enable pinctrl driver
engicam: icorem6: Add DM_GPIO, DM_MMC support
arm: dts: Add devicetree for i.MX6Q
arm: dts: imx6q: Add pinctrl defines
arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
mtd: nand: Kconfig: Add NAND_MXS entry
imx6: icorem6: Add NAND support
imx6: icorem6: Enable MTD device support
imx6: icorem6: Add default mtd nand partition table
arch/arm/cpu/armv7/mx6/Kconfig | 11 +
arch/arm/dts/Makefile | 4 +-
arch/arm/dts/imx6dl-icore.dts | 59 ++
arch/arm/dts/imx6dl-pinfunc.h | 1091 +++++++++++++++++++++++
arch/arm/dts/imx6dl.dtsi | 133 +++
arch/arm/dts/imx6q-icore.dts | 59 ++
arch/arm/dts/imx6q-pinfunc.h | 1047 ++++++++++++++++++++++
arch/arm/dts/imx6q.dtsi | 300 +++++++
arch/arm/dts/imx6qdl-icore.dtsi | 196 ++++
arch/arm/dts/imx6qdl.dtsi | 1281 +++++++++++++++++++++++++++
arch/arm/include/asm/imx-common/sys_proto.h | 2 +
board/barco/titanium/imximage.cfg | 2 +-
board/ccv/xpress/imximage.cfg | 2 +-
board/denx/m53evk/imximage.cfg | 2 +-
board/engicam/icorem6/Kconfig | 12 +
board/engicam/icorem6/MAINTAINERS | 6 +
board/engicam/icorem6/Makefile | 6 +
board/engicam/icorem6/README | 38 +
board/engicam/icorem6/icorem6.c | 537 +++++++++++
board/freescale/mx6sabresd/mx6dlsabresd.cfg | 2 +-
board/freescale/mx6slevk/imximage.cfg | 2 +-
board/freescale/mx6ullevk/imximage.cfg | 2 +-
board/freescale/mx7dsabresd/imximage.cfg | 2 +-
board/freescale/s32v234evb/s32v234evb.cfg | 2 +-
board/freescale/vf610twr/imximage.cfg | 2 +-
board/phytec/pcm052/imximage.cfg | 2 +-
board/technexion/pico-imx6ul/imximage.cfg | 2 +-
board/toradex/colibri_imx7/imximage.cfg | 2 +-
board/toradex/colibri_vf/imximage.cfg | 2 +-
board/warp/imximage.cfg | 2 +-
board/warp7/imximage.cfg | 2 +-
common/Kconfig | 5 +
configs/dms-ba16-1g_defconfig | 1 +
configs/dms-ba16_defconfig | 1 +
configs/ge_b450v3_defconfig | 1 +
configs/ge_b650v3_defconfig | 1 +
configs/ge_b850v3_defconfig | 1 +
configs/imx6qdl_icore_mmc_defconfig | 42 +
configs/imx6qdl_icore_nand_defconfig | 37 +
configs/mx25pdk_defconfig | 1 +
configs/mx53ard_defconfig | 1 +
configs/pico-imx6ul_defconfig | 1 +
configs/tqma6q_mba6_mmc_defconfig | 1 +
configs/tqma6q_mba6_spi_defconfig | 1 +
configs/tqma6s_mba6_mmc_defconfig | 1 +
configs/tqma6s_mba6_spi_defconfig | 1 +
configs/tqma6s_wru4_mmc_defconfig | 1 +
configs/zc5202_defconfig | 1 +
configs/zc5601_defconfig | 1 +
drivers/mtd/nand/Kconfig | 7 +
drivers/net/Kconfig | 7 +
drivers/serial/Kconfig | 7 +
drivers/thermal/Kconfig | 13 +
include/configs/advantech_dms-ba16.h | 1 -
include/configs/ge_bx50v3.h | 4 -
include/configs/imx6qdl_icore.h | 167 ++++
include/configs/mx25pdk.h | 2 -
include/configs/mx53ard.h | 2 -
include/configs/pico-imx6ul.h | 2 -
include/configs/tqma6_mba6.h | 6 -
include/configs/tqma6_wru4.h | 2 -
include/configs/zc5202.h | 2 -
include/configs/zc5601.h | 2 -
include/dt-bindings/clock/imx6qdl-clock.h | 274 ++++++
64 files changed, 5370 insertions(+), 39 deletions(-)
create mode 100644 arch/arm/dts/imx6dl-icore.dts
create mode 100644 arch/arm/dts/imx6dl-pinfunc.h
create mode 100644 arch/arm/dts/imx6dl.dtsi
create mode 100644 arch/arm/dts/imx6q-icore.dts
create mode 100644 arch/arm/dts/imx6q-pinfunc.h
create mode 100644 arch/arm/dts/imx6q.dtsi
create mode 100644 arch/arm/dts/imx6qdl-icore.dtsi
create mode 100644 arch/arm/dts/imx6qdl.dtsi
create mode 100644 board/engicam/icorem6/Kconfig
create mode 100644 board/engicam/icorem6/MAINTAINERS
create mode 100644 board/engicam/icorem6/Makefile
create mode 100644 board/engicam/icorem6/README
create mode 100644 board/engicam/icorem6/icorem6.c
create mode 100644 configs/imx6qdl_icore_mmc_defconfig
create mode 100644 configs/imx6qdl_icore_nand_defconfig
create mode 100644 include/configs/imx6qdl_icore.h
create mode 100644 include/dt-bindings/clock/imx6qdl-clock.h
--
2.7.4
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 01/21] serial: Kconfig: Add MXC_UART entry
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 02/21] thermal: Kconfig: Add IMX_THERMAL entry Jagan Teki
` (20 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Added kconfig for MXC_UART driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
drivers/serial/Kconfig | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 541cf2e..317d158 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -309,6 +309,13 @@ config MVEBU_A3700_UART
Choose this option to add support for UART driver on the Marvell
Armada 3700 SoC. The base address is configured via DT.
+config MXC_UART
+ bool "IMX serial port support"
+ depends on MX6
+ help
+ If you have a machine based on a Motorola IMX CPU you
+ can enable its onboard serial port by enabling this option.
+
config PIC32_SERIAL
bool "Support for Microchip PIC32 on-chip UART"
depends on DM_SERIAL && MACH_PIC32
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 02/21] thermal: Kconfig: Add IMX_THERMAL entry
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 01/21] serial: Kconfig: Add MXC_UART entry Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 03/21] config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs Jagan Teki
` (19 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Added kconfig for IMX_THERMAL driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
drivers/thermal/Kconfig | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 8e22ea7..f0ffbb3 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -5,3 +5,16 @@ config DM_THERMAL
temperature sensors to permit warnings, speed throttling or even
automatic power-off when the temperature gets too high or low. Other
devices may be discrete but connected on a suitable bus.
+
+if DM_THERMAL
+
+config IMX_THERMAL
+ bool "Temperature sensor driver for Freescale i.MX SoCs"
+ depends on MX6
+ help
+ Support for Temperature Monitor (TEMPMON) found on Freescale i.MX SoCs.
+ It supports one critical trip point and one passive trip point. The
+ cpufreq is used as the cooling device to throttle CPUs when the
+ passive trip is crossed.
+
+endif # if DM_THERMAL
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 03/21] config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 01/21] serial: Kconfig: Add MXC_UART entry Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 02/21] thermal: Kconfig: Add IMX_THERMAL entry Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 04/21] arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support Jagan Teki
` (18 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
- Add DEFAULT_FDT_FILE kconfig entry
- Move CONFIG_DEFAULT_FDT_FILE from include/configs to defconfigs
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
common/Kconfig | 5 +++++
configs/dms-ba16-1g_defconfig | 1 +
configs/dms-ba16_defconfig | 1 +
configs/ge_b450v3_defconfig | 1 +
configs/ge_b650v3_defconfig | 1 +
configs/ge_b850v3_defconfig | 1 +
configs/mx25pdk_defconfig | 1 +
configs/mx53ard_defconfig | 1 +
configs/pico-imx6ul_defconfig | 1 +
configs/tqma6q_mba6_mmc_defconfig | 1 +
configs/tqma6q_mba6_spi_defconfig | 1 +
configs/tqma6s_mba6_mmc_defconfig | 1 +
configs/tqma6s_mba6_spi_defconfig | 1 +
configs/tqma6s_wru4_mmc_defconfig | 1 +
configs/zc5202_defconfig | 1 +
configs/zc5601_defconfig | 1 +
include/configs/advantech_dms-ba16.h | 1 -
include/configs/ge_bx50v3.h | 4 ----
include/configs/mx25pdk.h | 2 --
include/configs/mx53ard.h | 2 --
include/configs/pico-imx6ul.h | 2 --
include/configs/tqma6_mba6.h | 6 ------
include/configs/tqma6_wru4.h | 2 --
include/configs/zc5202.h | 2 --
include/configs/zc5601.h | 2 --
25 files changed, 20 insertions(+), 23 deletions(-)
diff --git a/common/Kconfig b/common/Kconfig
index c69c141..9cbcbd4 100644
--- a/common/Kconfig
+++ b/common/Kconfig
@@ -203,6 +203,11 @@ config IDENT_STRING
help
This options adds the board specific name to u-boot version.
+config DEFAULT_FDT_FILE
+ string "Default fdt file"
+ help
+ This option is used to set the default fdt file to boot OS.
+
config SYS_NO_FLASH
bool "Disable support for parallel NOR flash"
default n
diff --git a/configs/dms-ba16-1g_defconfig b/configs/dms-ba16-1g_defconfig
index db5adcf..8e26837 100644
--- a/configs/dms-ba16-1g_defconfig
+++ b/configs/dms-ba16-1g_defconfig
@@ -1,6 +1,7 @@
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_ADVANTECH_DMS_BA16=y
+CONFIG_DEFAULT_FDT_FILE="imx6q-dms-ba16.dtb"
CONFIG_SYS_DDR_1G=y
CONFIG_BOOTDELAY=1
CONFIG_HUSH_PARSER=y
diff --git a/configs/dms-ba16_defconfig b/configs/dms-ba16_defconfig
index e36f3dc..fec0a1c 100644
--- a/configs/dms-ba16_defconfig
+++ b/configs/dms-ba16_defconfig
@@ -1,6 +1,7 @@
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_ADVANTECH_DMS_BA16=y
+CONFIG_DEFAULT_FDT_FILE="imx6q-dms-ba16.dtb"
CONFIG_BOOTDELAY=1
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
diff --git a/configs/ge_b450v3_defconfig b/configs/ge_b450v3_defconfig
index 8577167..4a5322d 100644
--- a/configs/ge_b450v3_defconfig
+++ b/configs/ge_b450v3_defconfig
@@ -1,6 +1,7 @@
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_GE_B450V3=y
+CONFIG_DEFAULT_FDT_FILE="/boot/imx6q-b450v3.dtb"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_BOOTDELAY=1
CONFIG_HUSH_PARSER=y
diff --git a/configs/ge_b650v3_defconfig b/configs/ge_b650v3_defconfig
index c5f391e..ecf4449 100644
--- a/configs/ge_b650v3_defconfig
+++ b/configs/ge_b650v3_defconfig
@@ -1,6 +1,7 @@
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_GE_B650V3=y
+CONFIG_DEFAULT_FDT_FILE="/boot/imx6q-b650v3.dtb"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_BOOTDELAY=1
CONFIG_HUSH_PARSER=y
diff --git a/configs/ge_b850v3_defconfig b/configs/ge_b850v3_defconfig
index 2c5aa05..004c9d0 100644
--- a/configs/ge_b850v3_defconfig
+++ b/configs/ge_b850v3_defconfig
@@ -1,6 +1,7 @@
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_GE_B850V3=y
+CONFIG_DEFAULT_FDT_FILE="/boot/imx6q-b850v3.dtb"
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_BOOTDELAY=1
CONFIG_HUSH_PARSER=y
diff --git a/configs/mx25pdk_defconfig b/configs/mx25pdk_defconfig
index b4afb05..c3ab7c2 100644
--- a/configs/mx25pdk_defconfig
+++ b/configs/mx25pdk_defconfig
@@ -1,6 +1,7 @@
CONFIG_ARM=y
CONFIG_TARGET_MX25PDK=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx25pdk/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx25-pdk.dtb"
CONFIG_BOOTDELAY=1
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
diff --git a/configs/mx53ard_defconfig b/configs/mx53ard_defconfig
index 7a62c2b..fe0f106 100644
--- a/configs/mx53ard_defconfig
+++ b/configs/mx53ard_defconfig
@@ -1,6 +1,7 @@
CONFIG_ARM=y
CONFIG_TARGET_MX53ARD=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx53ard/imximage_dd3.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx53-ard.dtb"
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
diff --git a/configs/pico-imx6ul_defconfig b/configs/pico-imx6ul_defconfig
index 1aaf868..dba67bb 100644
--- a/configs/pico-imx6ul_defconfig
+++ b/configs/pico-imx6ul_defconfig
@@ -2,6 +2,7 @@ CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_PICO_IMX6UL=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/technexion/pico-imx6ul/imximage.cfg"
+CONFIG_DEFAULT_FDT_FILE="imx6ul-pico-hobbit.dtb"
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
diff --git a/configs/tqma6q_mba6_mmc_defconfig b/configs/tqma6q_mba6_mmc_defconfig
index a827606..ff7b826 100644
--- a/configs/tqma6q_mba6_mmc_defconfig
+++ b/configs/tqma6q_mba6_mmc_defconfig
@@ -4,6 +4,7 @@ CONFIG_TARGET_TQMA6=y
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
+CONFIG_DEFAULT_FDT_FILE="imx6q-mba6x.dtb"
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
diff --git a/configs/tqma6q_mba6_spi_defconfig b/configs/tqma6q_mba6_spi_defconfig
index 29c7ad9..e6f99b1 100644
--- a/configs/tqma6q_mba6_spi_defconfig
+++ b/configs/tqma6q_mba6_spi_defconfig
@@ -5,6 +5,7 @@ CONFIG_TQMA6X_SPI_BOOT=y
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
+CONFIG_DEFAULT_FDT_FILE="imx6q-mba6x.dtb"
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
diff --git a/configs/tqma6s_mba6_mmc_defconfig b/configs/tqma6s_mba6_mmc_defconfig
index 426b4c0..33436fc 100644
--- a/configs/tqma6s_mba6_mmc_defconfig
+++ b/configs/tqma6s_mba6_mmc_defconfig
@@ -5,6 +5,7 @@ CONFIG_TQMA6S=y
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
+CONFIG_DEFAULT_FDT_FILE="imx6dl-mba6x.dtb"
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
diff --git a/configs/tqma6s_mba6_spi_defconfig b/configs/tqma6s_mba6_spi_defconfig
index 63df5ef..7805638 100644
--- a/configs/tqma6s_mba6_spi_defconfig
+++ b/configs/tqma6s_mba6_spi_defconfig
@@ -6,6 +6,7 @@ CONFIG_TQMA6X_SPI_BOOT=y
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
+CONFIG_DEFAULT_FDT_FILE="imx6dl-mba6x.dtb"
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
diff --git a/configs/tqma6s_wru4_mmc_defconfig b/configs/tqma6s_wru4_mmc_defconfig
index fa3c7d8..0f5950d 100644
--- a/configs/tqma6s_wru4_mmc_defconfig
+++ b/configs/tqma6s_wru4_mmc_defconfig
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_KEYED=y
CONFIG_AUTOBOOT_PROMPT="Enter password in %d seconds to stop autoboot\n"
CONFIG_AUTOBOOT_ENCRYPTION=y
CONFIG_AUTOBOOT_STOP_STR_SHA256="36a9e7f1c95b82ffb99743e0c5c4ce95d83c9a430aac59f84ef3cbfab6145068"
+CONFIG_DEFAULT_FDT_FILE="imx6s-wru4.dtb"
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_MMC=y
diff --git a/configs/zc5202_defconfig b/configs/zc5202_defconfig
index 8d3f1df..c979854 100644
--- a/configs/zc5202_defconfig
+++ b/configs/zc5202_defconfig
@@ -13,6 +13,7 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
CONFIG_SPL_WATCHDOG_SUPPORT=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,MX6Q"
+CONFIG_DEFAULT_FDT_FILE="imx6q-zc5202.dtb"
CONFIG_BOOTDELAY=3
CONFIG_SPL=y
CONFIG_CMD_MMC=y
diff --git a/configs/zc5601_defconfig b/configs/zc5601_defconfig
index a72c0e9..a539e58 100644
--- a/configs/zc5601_defconfig
+++ b/configs/zc5601_defconfig
@@ -13,6 +13,7 @@ CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
CONFIG_SPL_WATCHDOG_SUPPORT=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,MX6Q"
+CONFIG_DEFAULT_FDT_FILE="imx6q-zc5601.dtb"
CONFIG_BOOTDELAY=3
CONFIG_SPL=y
CONFIG_CMD_MMC=y
diff --git a/include/configs/advantech_dms-ba16.h b/include/configs/advantech_dms-ba16.h
index 992948a..7efcd55 100644
--- a/include/configs/advantech_dms-ba16.h
+++ b/include/configs/advantech_dms-ba16.h
@@ -13,7 +13,6 @@
#include <asm/imx-common/gpio.h>
#define CONFIG_BOARD_NAME "Advantech DMS-BA16"
-#define CONFIG_DEFAULT_FDT_FILE "imx6q-dms-ba16.dtb"
#define CONFIG_MXC_UART_BASE UART4_BASE
#define CONFIG_CONSOLE_DEV "ttymxc3"
diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h
index c77fef6..f38c9a0 100644
--- a/include/configs/ge_bx50v3.h
+++ b/include/configs/ge_bx50v3.h
@@ -18,19 +18,15 @@
#define BX50V3_BOOTARGS_EXTRA
#if defined(CONFIG_TARGET_GE_B450V3)
#define CONFIG_BOARD_NAME "General Electric B450v3"
-#define CONFIG_DEFAULT_FDT_FILE "/boot/imx6q-b450v3.dtb"
#elif defined(CONFIG_TARGET_GE_B650V3)
#define CONFIG_BOARD_NAME "General Electric B650v3"
-#define CONFIG_DEFAULT_FDT_FILE "/boot/imx6q-b650v3.dtb"
#elif defined(CONFIG_TARGET_GE_B850V3)
#define CONFIG_BOARD_NAME "General Electric B850v3"
-#define CONFIG_DEFAULT_FDT_FILE "/boot/imx6q-b850v3.dtb"
#undef BX50V3_BOOTARGS_EXTRA
#define BX50V3_BOOTARGS_EXTRA "video=DP-1:1024x768 at 60 " \
"video=HDMI-A-1:1024x768 at 60 "
#else
#define CONFIG_BOARD_NAME "General Electric BA16 Generic"
-#define CONFIG_DEFAULT_FDT_FILE "/boot/imx6q-ba16.dtb"
#endif
#define CONFIG_MXC_UART_BASE UART3_BASE
diff --git a/include/configs/mx25pdk.h b/include/configs/mx25pdk.h
index ea0d605..3bbcb29 100644
--- a/include/configs/mx25pdk.h
+++ b/include/configs/mx25pdk.h
@@ -121,8 +121,6 @@
#define CONFIG_LOADADDR 0x81000000 /* loadaddr env var */
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_DEFAULT_FDT_FILE "imx25-pdk.dtb"
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
"image=zImage\0" \
diff --git a/include/configs/mx53ard.h b/include/configs/mx53ard.h
index 0419050..74b65af 100644
--- a/include/configs/mx53ard.h
+++ b/include/configs/mx53ard.h
@@ -81,8 +81,6 @@
#define CONFIG_LOADADDR 0x72000000 /* loadaddr env var */
#define CONFIG_SYS_TEXT_BASE 0x77800000
-#define CONFIG_DEFAULT_FDT_FILE "imx53-ard.dtb"
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
"uimage=zImage\0" \
diff --git a/include/configs/pico-imx6ul.h b/include/configs/pico-imx6ul.h
index ed3b64f..2aa9ea9 100644
--- a/include/configs/pico-imx6ul.h
+++ b/include/configs/pico-imx6ul.h
@@ -61,8 +61,6 @@
#define CONFIG_SYS_DFU_DATA_BUF_SIZE SZ_16M
#define DFU_DEFAULT_POLL_TIMEOUT 300
-#define CONFIG_DEFAULT_FDT_FILE "imx6ul-pico-hobbit.dtb"
-
#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
#define CONFIG_EXTRA_ENV_SETTINGS \
diff --git a/include/configs/tqma6_mba6.h b/include/configs/tqma6_mba6.h
index 2f52598..ab8ab76 100644
--- a/include/configs/tqma6_mba6.h
+++ b/include/configs/tqma6_mba6.h
@@ -9,12 +9,6 @@
#ifndef __CONFIG_TQMA6_MBA6_H
#define __CONFIG_TQMA6_MBA6_H
-#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
-#define CONFIG_DEFAULT_FDT_FILE "imx6dl-mba6x.dtb"
-#elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
-#define CONFIG_DEFAULT_FDT_FILE "imx6q-mba6x.dtb"
-#endif
-
#define CONFIG_DTT_SENSORS { 0, 1 }
#define CONFIG_FEC_XCV_TYPE RGMII
diff --git a/include/configs/tqma6_wru4.h b/include/configs/tqma6_wru4.h
index 8896bc3..faca0fd 100644
--- a/include/configs/tqma6_wru4.h
+++ b/include/configs/tqma6_wru4.h
@@ -7,8 +7,6 @@
#ifndef __CONFIG_TQMA6_WRU4_H
#define __CONFIG_TQMA6_WRU4_H
-#define CONFIG_DEFAULT_FDT_FILE "imx6s-wru4.dtb"
-
/* DTT sensors */
#define CONFIG_DTT_SENSORS { 0, 1 }
#define CONFIG_SYS_DTT_BUS_NUM 2
diff --git a/include/configs/zc5202.h b/include/configs/zc5202.h
index 073a42c..040c695 100644
--- a/include/configs/zc5202.h
+++ b/include/configs/zc5202.h
@@ -13,8 +13,6 @@
#define CONFIG_CONSOLE_DEV "ttymxc1"
#define CONFIG_MMCROOT "/dev/mmcblk0p2"
-#define CONFIG_DEFAULT_FDT_FILE "imx6q-zc5202.dtb"
-
#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
#include "el6x_common.h"
diff --git a/include/configs/zc5601.h b/include/configs/zc5601.h
index 28b9c6b..7c24a50 100644
--- a/include/configs/zc5601.h
+++ b/include/configs/zc5601.h
@@ -14,8 +14,6 @@
#define CONFIG_CONSOLE_DEV "ttymxc1"
#define CONFIG_MMCROOT "/dev/mmcblk0p1"
-#define CONFIG_DEFAULT_FDT_FILE "imx6q-zc5601.dtb"
-
#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
#include "el6x_common.h"
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 04/21] arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (2 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 03/21] config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 05/21] net: Kconfig: Add FEC_MXC entry Jagan Teki
` (17 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Boot Log for i.CoreM6 DualLite/Solo Starter Kit:
-----------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM: 256 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800a787
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6Q rev1.2 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
icorem6qdl>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/cpu/armv7/mx6/Kconfig | 8 +
arch/arm/include/asm/imx-common/sys_proto.h | 2 +
board/engicam/icorem6/Kconfig | 12 +
board/engicam/icorem6/MAINTAINERS | 6 +
board/engicam/icorem6/Makefile | 6 +
board/engicam/icorem6/README | 31 +++
board/engicam/icorem6/icorem6.c | 400 ++++++++++++++++++++++++++++
configs/imx6qdl_icore_mmc_defconfig | 35 +++
include/configs/imx6qdl_icore.h | 120 +++++++++
9 files changed, 620 insertions(+)
create mode 100644 board/engicam/icorem6/Kconfig
create mode 100644 board/engicam/icorem6/MAINTAINERS
create mode 100644 board/engicam/icorem6/Makefile
create mode 100644 board/engicam/icorem6/README
create mode 100644 board/engicam/icorem6/icorem6.c
create mode 100644 configs/imx6qdl_icore_mmc_defconfig
create mode 100644 include/configs/imx6qdl_icore.h
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index d851b26..5d549bd 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -95,6 +95,13 @@ config TARGET_MX6CUBOXI
config TARGET_MX6QARM2
bool "mx6qarm2"
+config TARGET_MX6Q_ICORE
+ bool "Support Engicam i.Core"
+ select MX6QDL
+ select DM
+ select DM_THERMAL
+ select SUPPORT_SPL
+
config TARGET_MX6QSABREAUTO
bool "mx6qsabreauto"
select DM
@@ -225,6 +232,7 @@ source "board/compulab/cm_fx6/Kconfig"
source "board/congatec/cgtqmx6eval/Kconfig"
source "board/el/el6x/Kconfig"
source "board/embest/mx6boards/Kconfig"
+source "board/engicam/icorem6/Kconfig"
source "board/freescale/mx6qarm2/Kconfig"
source "board/freescale/mx6qsabreauto/Kconfig"
source "board/freescale/mx6sabresd/Kconfig"
diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h
index 6ace8bb..005435a 100644
--- a/arch/arm/include/asm/imx-common/sys_proto.h
+++ b/arch/arm/include/asm/imx-common/sys_proto.h
@@ -30,8 +30,10 @@
#define is_mx6dqp() (is_cpu_type(MXC_CPU_MX6QP) || is_cpu_type(MXC_CPU_MX6DP))
#define is_mx6dq() (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
#define is_mx6sdl() (is_cpu_type(MXC_CPU_MX6SOLO) || is_cpu_type(MXC_CPU_MX6DL))
+#define is_mx6dl() (is_cpu_type(MXC_CPU_MX6DL))
#define is_mx6sx() (is_cpu_type(MXC_CPU_MX6SX))
#define is_mx6sl() (is_cpu_type(MXC_CPU_MX6SL))
+#define is_mx6solo() (is_cpu_type(MXC_CPU_MX6SOLO))
#define is_mx6ul() (is_cpu_type(MXC_CPU_MX6UL))
#define is_mx6ull() (is_cpu_type(MXC_CPU_MX6ULL))
diff --git a/board/engicam/icorem6/Kconfig b/board/engicam/icorem6/Kconfig
new file mode 100644
index 0000000..6d62f0e
--- /dev/null
+++ b/board/engicam/icorem6/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_MX6Q_ICORE
+
+config SYS_BOARD
+ default "icorem6"
+
+config SYS_VENDOR
+ default "engicam"
+
+config SYS_CONFIG_NAME
+ default "imx6qdl_icore"
+
+endif
diff --git a/board/engicam/icorem6/MAINTAINERS b/board/engicam/icorem6/MAINTAINERS
new file mode 100644
index 0000000..3e06c6b
--- /dev/null
+++ b/board/engicam/icorem6/MAINTAINERS
@@ -0,0 +1,6 @@
+ICOREM6QDL BOARD
+M: Jagan Teki <jagan@amarulasolutions.com>
+S: Maintained
+F: board/engicam/icorem6
+F: include/configs/icorem6qdl.h
+F: configs/icorem6qdl_defconfig
diff --git a/board/engicam/icorem6/Makefile b/board/engicam/icorem6/Makefile
new file mode 100644
index 0000000..9ec9ecd
--- /dev/null
+++ b/board/engicam/icorem6/Makefile
@@ -0,0 +1,6 @@
+# Copyright (C) 2016 Amarula Solutions B.V.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := icorem6.o
diff --git a/board/engicam/icorem6/README b/board/engicam/icorem6/README
new file mode 100644
index 0000000..cf2eff2
--- /dev/null
+++ b/board/engicam/icorem6/README
@@ -0,0 +1,31 @@
+How to use U-Boot on Engicam i.CoreM6 DualLite/Solo and Quad/Dual Starter Kit:
+-----------------------------------------------------------------------------
+
+- Build U-Boot for Engicam i.CoreM6 QDL:
+
+$ make mrproper
+$ make icorem6qdl_mmc_defconfig
+$ make
+
+This will generate the SPL image called SPL and the u-boot.img.
+
+- Flash the SPL image into the micro SD card:
+
+sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+
+- Flash the u-boot.img image into the micro SD card:
+
+sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Jumper settings:
+
+MMC Boot: JM3 Closed
+
+- Connect the Serial cable between the Starter Kit and the PC for the console.
+(J28 is the Linux Serial console connector)
+
+- Insert the micro SD card in the board, power it up and U-Boot messages should
+come up.
+
+- Note: For loading Linux on Quad/Dual modules set the dtb as
+ icorem6qdl> setenv fdt_file imx6q-icore.dtb
diff --git a/board/engicam/icorem6/icorem6.c b/board/engicam/icorem6/icorem6.c
new file mode 100644
index 0000000..1856972
--- /dev/null
+++ b/board/engicam/icorem6/icorem6.c
@@ -0,0 +1,400 @@
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <linux/sizes.h>
+
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/imx-common/iomux-v3.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const uart4_pads[] = {
+ IOMUX_PADS(PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+ IOMUX_PADS(PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+};
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+ IOMUX_PADS(PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL)),/* CD */
+};
+
+#ifdef CONFIG_FSL_ESDHC
+#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 1)
+
+struct fsl_esdhc_cfg usdhc_cfg[1] = {
+ {USDHC1_BASE_ADDR, 0, 4},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = !gpio_get_value(USDHC1_CD_GPIO);
+ break;
+ }
+
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int i, ret;
+
+ /*
+ * According to the board_mmc_init() the following map is done:
+ * (U-boot device node) (Physical Port)
+ * mmc0 USDHC1
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ SETUP_IOMUX_PADS(usdhc1_pads);
+ gpio_direction_input(USDHC1_CD_GPIO);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+ default:
+ printf("Warning - USDHC%d controller not supporting\n",
+ i + 1);
+ return 0;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret) {
+ printf("Warning: failed to initialize mmc dev %d\n", i);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+#endif
+
+int board_early_init_f(void)
+{
+ SETUP_IOMUX_PADS(uart4_pads);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+
+ return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+#include <libfdt.h>
+#include <spl.h>
+
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6-ddr.h>
+
+/*
+ * Driving strength:
+ * 0x30 == 40 Ohm
+ * 0x28 == 48 Ohm
+ */
+
+#define IMX6DQ_DRIVE_STRENGTH 0x30
+#define IMX6SDL_DRIVE_STRENGTH 0x28
+
+/* configure MX6Q/DUAL mmdc DDR io registers */
+static struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = {
+ .dram_sdqs0 = 0x28,
+ .dram_sdqs1 = 0x28,
+ .dram_sdqs2 = 0x28,
+ .dram_sdqs3 = 0x28,
+ .dram_sdqs4 = 0x28,
+ .dram_sdqs5 = 0x28,
+ .dram_sdqs6 = 0x28,
+ .dram_sdqs7 = 0x28,
+ .dram_dqm0 = 0x28,
+ .dram_dqm1 = 0x28,
+ .dram_dqm2 = 0x28,
+ .dram_dqm3 = 0x28,
+ .dram_dqm4 = 0x28,
+ .dram_dqm5 = 0x28,
+ .dram_dqm6 = 0x28,
+ .dram_dqm7 = 0x28,
+ .dram_cas = 0x30,
+ .dram_ras = 0x30,
+ .dram_sdclk_0 = 0x30,
+ .dram_sdclk_1 = 0x30,
+ .dram_reset = 0x30,
+ .dram_sdcke0 = 0x3000,
+ .dram_sdcke1 = 0x3000,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdodt0 = 0x30,
+ .dram_sdodt1 = 0x30,
+};
+
+/* configure MX6Q/DUAL mmdc GRP io registers */
+static struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = {
+ .grp_b0ds = 0x30,
+ .grp_b1ds = 0x30,
+ .grp_b2ds = 0x30,
+ .grp_b3ds = 0x30,
+ .grp_b4ds = 0x30,
+ .grp_b5ds = 0x30,
+ .grp_b6ds = 0x30,
+ .grp_b7ds = 0x30,
+ .grp_addds = 0x30,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_ddrpke = 0x00000000,
+ .grp_ddrmode = 0x00020000,
+ .grp_ctlds = 0x30,
+ .grp_ddr_type = 0x000c0000,
+};
+
+/* configure MX6SOLO/DUALLITE mmdc DDR io registers */
+struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
+ .dram_sdclk_0 = 0x30,
+ .dram_sdclk_1 = 0x30,
+ .dram_cas = 0x30,
+ .dram_ras = 0x30,
+ .dram_reset = 0x30,
+ .dram_sdcke0 = 0x30,
+ .dram_sdcke1 = 0x30,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdodt0 = 0x30,
+ .dram_sdodt1 = 0x30,
+ .dram_sdqs0 = 0x28,
+ .dram_sdqs1 = 0x28,
+ .dram_sdqs2 = 0x28,
+ .dram_sdqs3 = 0x28,
+ .dram_sdqs4 = 0x28,
+ .dram_sdqs5 = 0x28,
+ .dram_sdqs6 = 0x28,
+ .dram_sdqs7 = 0x28,
+ .dram_dqm0 = 0x28,
+ .dram_dqm1 = 0x28,
+ .dram_dqm2 = 0x28,
+ .dram_dqm3 = 0x28,
+ .dram_dqm4 = 0x28,
+ .dram_dqm5 = 0x28,
+ .dram_dqm6 = 0x28,
+ .dram_dqm7 = 0x28,
+};
+
+/* configure MX6SOLO/DUALLITE mmdc GRP io registers */
+struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
+ .grp_ddr_type = 0x000c0000,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_ddrpke = 0x00000000,
+ .grp_addds = 0x30,
+ .grp_ctlds = 0x30,
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x28,
+ .grp_b1ds = 0x28,
+ .grp_b2ds = 0x28,
+ .grp_b3ds = 0x28,
+ .grp_b4ds = 0x28,
+ .grp_b5ds = 0x28,
+ .grp_b6ds = 0x28,
+ .grp_b7ds = 0x28,
+};
+
+/* mt41j256 */
+static struct mx6_ddr3_cfg mt41j256 = {
+ .mem_speed = 1066,
+ .density = 2,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 13,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+ .SRT = 0,
+};
+
+static struct mx6_mmdc_calibration mx6dq_mmdc_calib = {
+ .p0_mpwldectrl0 = 0x000E0009,
+ .p0_mpwldectrl1 = 0x0018000E,
+ .p1_mpwldectrl0 = 0x00000007,
+ .p1_mpwldectrl1 = 0x00000000,
+ .p0_mpdgctrl0 = 0x43280334,
+ .p0_mpdgctrl1 = 0x031C0314,
+ .p1_mpdgctrl0 = 0x4318031C,
+ .p1_mpdgctrl1 = 0x030C0258,
+ .p0_mprddlctl = 0x3E343A40,
+ .p1_mprddlctl = 0x383C3844,
+ .p0_mpwrdlctl = 0x40404440,
+ .p1_mpwrdlctl = 0x4C3E4446,
+};
+
+/* DDR 64bit */
+static struct mx6_ddr_sysinfo mem_q = {
+ .ddr_type = DDR_TYPE_DDR3,
+ .dsize = 2,
+ .cs1_mirror = 0,
+ /* config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32,
+ .ncs = 1,
+ .bi_on = 1,
+ .rtt_nom = 2,
+ .rtt_wr = 2,
+ .ralat = 5,
+ .walat = 0,
+ .mif3_mode = 3,
+ .rst_to_cke = 0x23,
+ .sde_to_rst = 0x10,
+};
+
+static struct mx6_mmdc_calibration mx6dl_mmdc_calib = {
+ .p0_mpwldectrl0 = 0x001F0024,
+ .p0_mpwldectrl1 = 0x00110018,
+ .p1_mpwldectrl0 = 0x001F0024,
+ .p1_mpwldectrl1 = 0x00110018,
+ .p0_mpdgctrl0 = 0x4230022C,
+ .p0_mpdgctrl1 = 0x02180220,
+ .p1_mpdgctrl0 = 0x42440248,
+ .p1_mpdgctrl1 = 0x02300238,
+ .p0_mprddlctl = 0x44444A48,
+ .p1_mprddlctl = 0x46484A42,
+ .p0_mpwrdlctl = 0x38383234,
+ .p1_mpwrdlctl = 0x3C34362E,
+};
+
+/* DDR 64bit 1GB */
+static struct mx6_ddr_sysinfo mem_dl = {
+ .dsize = 2,
+ .cs1_mirror = 0,
+ /* config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32,
+ .ncs = 1,
+ .bi_on = 1,
+ .rtt_nom = 1,
+ .rtt_wr = 1,
+ .ralat = 5,
+ .walat = 0,
+ .mif3_mode = 3,
+ .rst_to_cke = 0x23,
+ .sde_to_rst = 0x10,
+};
+
+/* DDR 32bit 512MB */
+static struct mx6_ddr_sysinfo mem_s = {
+ .dsize = 1,
+ .cs1_mirror = 0,
+ /* config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32,
+ .ncs = 1,
+ .bi_on = 1,
+ .rtt_nom = 1,
+ .rtt_wr = 1,
+ .ralat = 5,
+ .walat = 0,
+ .mif3_mode = 3,
+ .rst_to_cke = 0x23,
+ .sde_to_rst = 0x10,
+};
+
+static void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ writel(0x00003F3F, &ccm->CCGR0);
+ writel(0x0030FC00, &ccm->CCGR1);
+ writel(0x000FC000, &ccm->CCGR2);
+ writel(0x3F300000, &ccm->CCGR3);
+ writel(0xFF00F300, &ccm->CCGR4);
+ writel(0x0F0000C3, &ccm->CCGR5);
+ writel(0x000003CC, &ccm->CCGR6);
+}
+
+static void gpr_init(void)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ /* enable AXI cache for VDOA/VPU/IPU */
+ writel(0xF00000CF, &iomux->gpr[4]);
+ /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+ writel(0x007F007F, &iomux->gpr[6]);
+ writel(0x007F007F, &iomux->gpr[7]);
+}
+
+static void spl_dram_init(void)
+{
+ if (is_mx6solo()) {
+ mx6sdl_dram_iocfg(32, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
+ mx6_dram_cfg(&mem_s, &mx6dl_mmdc_calib, &mt41j256);
+ } else if (is_mx6dl()) {
+ mx6sdl_dram_iocfg(64, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
+ mx6_dram_cfg(&mem_dl, &mx6dl_mmdc_calib, &mt41j256);
+ } else if (is_mx6dq()) {
+ mx6dq_dram_iocfg(64, &mx6dq_ddr_ioregs, &mx6dq_grp_ioregs);
+ mx6_dram_cfg(&mem_q, &mx6dq_mmdc_calib, &mt41j256);
+ }
+
+ udelay(100);
+}
+
+void board_init_f(ulong dummy)
+{
+ ccgr_init();
+
+ /* setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ gpr_init();
+
+ /* iomux */
+ board_early_init_f();
+
+ /* setup GP timer */
+ timer_init();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* DDR initialization */
+ spl_dram_init();
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ /* load/boot image from boot device */
+ board_init_r(NULL, 0);
+}
+#endif
diff --git a/configs/imx6qdl_icore_mmc_defconfig b/configs/imx6qdl_icore_mmc_defconfig
new file mode 100644
index 0000000..ced6b10
--- /dev/null
+++ b/configs/imx6qdl_icore_mmc_defconfig
@@ -0,0 +1,35 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_MX6Q_ICORE=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,ENV_IS_IN_MMC"
+CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
+CONFIG_SYS_PROMPT="icorem6qdl> "
+CONFIG_SPL=y
+CONFIG_BOOTDELAY=3
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_DISPLAY_CPUINFO=y
+CONFIG_HUSH_PARSER=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_SYS_MAXARGS=32
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_OF_LIBFDT=y
+CONFIG_MXC_UART=y
+CONFIG_IMX_THERMAL=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_SPL_EXT_SUPPORT=y
diff --git a/include/configs/imx6qdl_icore.h b/include/configs/imx6qdl_icore.h
new file mode 100644
index 0000000..0bd0f23
--- /dev/null
+++ b/include/configs/imx6qdl_icore.h
@@ -0,0 +1,120 @@
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * Configuration settings for the Engicam i.CoreM6 QDL Starter Kits.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __IMX6QLD_ICORE_CONFIG_H
+#define __IMX6QLD_ICORE_CONFIG_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (16 * SZ_1M)
+
+/* Total Size of Environment Sector */
+#define CONFIG_ENV_SIZE SZ_128K
+
+/* Allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Environment */
+#ifndef CONFIG_ENV_IS_NOWHERE
+/* Environment in MMC */
+# if defined(CONFIG_ENV_IS_IN_MMC)
+# define CONFIG_ENV_OFFSET 0x100000
+# endif
+#endif
+
+/* Default environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "image=zImage\0" \
+ "console=ttymxc3\0" \
+ "fdt_high=0xffffffff\0" \
+ "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+ "fdt_addr=0x18000000\0" \
+ "boot_fdt=try\0" \
+ "mmcdev=0\0" \
+ "mmcpart=1\0" \
+ "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
+ "mmcautodetect=yes\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev};" \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "fi; " \
+ "fi; " \
+ "fi"
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x8000000)
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_SP_OFFSET)
+
+/* UART */
+#ifdef CONFIG_MXC_UART
+# define CONFIG_MXC_UART_BASE UART4_BASE
+#endif
+
+/* MMC */
+#ifdef CONFIG_FSL_USDHC
+# define CONFIG_SYS_MMC_ENV_DEV 0
+# define CONFIG_SYS_FSL_USDHC_NUM 1
+# define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
+#endif
+
+/* SPL */
+#ifdef CONFIG_SPL
+# define CONFIG_SPL_MMC_SUPPORT
+# include "imx6_spl.h"
+#endif
+
+#endif /* __IMX6QLD_ICORE_CONFIG_H */
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 05/21] net: Kconfig: Add FEC_MXC entry
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (3 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 04/21] arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 06/21] imx6: icorem6: Add ENET support Jagan Teki
` (16 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Added kconfig for FEC_MXC driver.
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
drivers/net/Kconfig | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 302c005..7b9961d 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -129,6 +129,13 @@ config ETHOC
help
This MAC is present in OpenRISC and Xtensa XTFPGA boards.
+config FEC_MXC
+ bool "FEC Ethernet controller"
+ depends on MX6
+ help
+ This driver supports the 10/100 Fast Ethernet controller for
+ NXP i.MX processors.
+
config MVPP2
bool "Marvell Armada 375 network interface support"
depends on ARMADA_375
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 06/21] imx6: icorem6: Add ENET support
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (4 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 05/21] net: Kconfig: Add FEC_MXC entry Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 07/21] imx: s/docs\/README.imximage/doc\/README.imximage/g Jagan Teki
` (15 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add enet support for engicam icorem6 qdl starter kit.
- Add pinmux settings
- Add board_eth_init
TFTP log:
--------
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
icorem6qdl> tftpboot {fdt_addr} imx6dl-icore.dtb
Using FEC device
TFTP from server 192.168.2.96; our IP address is 192.168.2.75
Filename 'imx6dl-icore.dtb'.
Load address: 0x0
Loading: ######
1.3 MiB/s
done
Bytes transferred = 28976 (7130 hex)
CACHE: Misaligned operation at range [00000000, 00007130]
icorem6qdl>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
---
board/engicam/icorem6/icorem6.c | 72 +++++++++++++++++++++++++++++++++++++
configs/imx6qdl_icore_mmc_defconfig | 4 +++
include/configs/imx6qdl_icore.h | 12 +++++++
3 files changed, 88 insertions(+)
diff --git a/board/engicam/icorem6/icorem6.c b/board/engicam/icorem6/icorem6.c
index 1856972..a23cb7e 100644
--- a/board/engicam/icorem6/icorem6.c
+++ b/board/engicam/icorem6/icorem6.c
@@ -9,12 +9,15 @@
#include <common.h>
#include <fsl_esdhc.h>
#include <mmc.h>
+#include <miiphy.h>
+#include <netdev.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <linux/sizes.h>
#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
@@ -30,11 +33,28 @@ DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
static iomux_v3_cfg_t const uart4_pads[] = {
IOMUX_PADS(PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
+static iomux_v3_cfg_t const enet_pads[] = {
+ IOMUX_PADS(PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL | PAD_CTL_SRE_FAST)),
+ IOMUX_PADS(PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
static iomux_v3_cfg_t const usdhc1_pads[] = {
IOMUX_PADS(PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
@@ -99,6 +119,58 @@ int board_mmc_init(bd_t *bis)
}
#endif
+#ifdef CONFIG_FEC_MXC
+#define ENET_PHY_RST IMX_GPIO_NR(7, 12)
+static int setup_fec(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
+ s32 timeout = 100000;
+ u32 reg = 0;
+ int ret;
+
+ /* Enable fec clock */
+ setbits_le32(&ccm->CCGR1, MXC_CCM_CCGR1_ENET_MASK);
+
+ /* use 50MHz */
+ ret = enable_fec_anatop_clock(0, ENET_50MHZ);
+ if (ret)
+ return ret;
+
+ /* Enable PLLs */
+ reg = readl(&anatop->pll_enet);
+ reg &= ~BM_ANADIG_PLL_SYS_POWERDOWN;
+ writel(reg, &anatop->pll_enet);
+ reg = readl(&anatop->pll_enet);
+ reg |= BM_ANADIG_PLL_SYS_ENABLE;
+ while (timeout--) {
+ if (readl(&anatop->pll_enet) & BM_ANADIG_PLL_SYS_LOCK)
+ break;
+ }
+ if (timeout <= 0)
+ return -EIO;
+ reg &= ~BM_ANADIG_PLL_SYS_BYPASS;
+ writel(reg, &anatop->pll_enet);
+
+ /* reset the phy */
+ gpio_direction_output(ENET_PHY_RST, 0);
+ udelay(10000);
+ gpio_set_value(ENET_PHY_RST, 1);
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int ret;
+
+ SETUP_IOMUX_PADS(enet_pads);
+ setup_fec();
+
+ return ret = cpu_eth_init(bis);
+}
+#endif
+
int board_early_init_f(void)
{
SETUP_IOMUX_PADS(uart4_pads);
diff --git a/configs/imx6qdl_icore_mmc_defconfig b/configs/imx6qdl_icore_mmc_defconfig
index ced6b10..c2c2fe8 100644
--- a/configs/imx6qdl_icore_mmc_defconfig
+++ b/configs/imx6qdl_icore_mmc_defconfig
@@ -14,6 +14,8 @@ CONFIG_SYS_MAXARGS=32
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_BOOTZ=y
CONFIG_CMD_GPIO=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_MMC=y
CONFIG_CMD_CACHE=y
@@ -23,7 +25,9 @@ CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_LIBFDT=y
+CONFIG_FEC_MXC=y
CONFIG_MXC_UART=y
+CONFIG_NETDEVICES=y
CONFIG_IMX_THERMAL=y
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
diff --git a/include/configs/imx6qdl_icore.h b/include/configs/imx6qdl_icore.h
index 0bd0f23..ad4c5f2 100644
--- a/include/configs/imx6qdl_icore.h
+++ b/include/configs/imx6qdl_icore.h
@@ -111,6 +111,18 @@
# define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
#endif
+/* Ethernet */
+#ifdef CONFIG_FEC_MXC
+# define IMX_FEC_BASE ENET_BASE_ADDR
+# define CONFIG_FEC_MXC_PHYADDR 0
+# define CONFIG_FEC_XCV_TYPE RMII
+# define CONFIG_ETHPRIME "FEC"
+
+# define CONFIG_MII
+# define CONFIG_PHYLIB
+# define CONFIG_PHY_SMSC
+#endif
+
/* SPL */
#ifdef CONFIG_SPL
# define CONFIG_SPL_MMC_SUPPORT
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 07/21] imx: s/docs\/README.imximage/doc\/README.imximage/g
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (5 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 06/21] imx6: icorem6: Add ENET support Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 08/21] arm: dts: Add devicetree for i.MX6DL Jagan Teki
` (14 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Fixed typo for doc/README.imximage on respective imximage.cfg files.
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/barco/titanium/imximage.cfg | 2 +-
board/ccv/xpress/imximage.cfg | 2 +-
board/denx/m53evk/imximage.cfg | 2 +-
board/freescale/mx6sabresd/mx6dlsabresd.cfg | 2 +-
board/freescale/mx6slevk/imximage.cfg | 2 +-
board/freescale/mx6ullevk/imximage.cfg | 2 +-
board/freescale/mx7dsabresd/imximage.cfg | 2 +-
board/freescale/s32v234evb/s32v234evb.cfg | 2 +-
board/freescale/vf610twr/imximage.cfg | 2 +-
board/phytec/pcm052/imximage.cfg | 2 +-
board/technexion/pico-imx6ul/imximage.cfg | 2 +-
board/toradex/colibri_imx7/imximage.cfg | 2 +-
board/toradex/colibri_vf/imximage.cfg | 2 +-
board/warp/imximage.cfg | 2 +-
board/warp7/imximage.cfg | 2 +-
15 files changed, 15 insertions(+), 15 deletions(-)
diff --git a/board/barco/titanium/imximage.cfg b/board/barco/titanium/imximage.cfg
index 7219256..4fb6982 100644
--- a/board/barco/titanium/imximage.cfg
+++ b/board/barco/titanium/imximage.cfg
@@ -7,7 +7,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/ccv/xpress/imximage.cfg b/board/ccv/xpress/imximage.cfg
index 92167c9..d98bc36 100644
--- a/board/ccv/xpress/imximage.cfg
+++ b/board/ccv/xpress/imximage.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/denx/m53evk/imximage.cfg b/board/denx/m53evk/imximage.cfg
index 4cd002c..c0e2602 100644
--- a/board/denx/m53evk/imximage.cfg
+++ b/board/denx/m53evk/imximage.cfg
@@ -4,7 +4,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/freescale/mx6sabresd/mx6dlsabresd.cfg b/board/freescale/mx6sabresd/mx6dlsabresd.cfg
index f35f22e..be9f87f 100644
--- a/board/freescale/mx6sabresd/mx6dlsabresd.cfg
+++ b/board/freescale/mx6sabresd/mx6dlsabresd.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/freescale/mx6slevk/imximage.cfg b/board/freescale/mx6slevk/imximage.cfg
index c77bbde..024de9c 100644
--- a/board/freescale/mx6slevk/imximage.cfg
+++ b/board/freescale/mx6slevk/imximage.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/freescale/mx6ullevk/imximage.cfg b/board/freescale/mx6ullevk/imximage.cfg
index 4604b62..3ae4912 100644
--- a/board/freescale/mx6ullevk/imximage.cfg
+++ b/board/freescale/mx6ullevk/imximage.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/freescale/mx7dsabresd/imximage.cfg b/board/freescale/mx7dsabresd/imximage.cfg
index 76574ff..c2b3a8c 100644
--- a/board/freescale/mx7dsabresd/imximage.cfg
+++ b/board/freescale/mx7dsabresd/imximage.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/freescale/s32v234evb/s32v234evb.cfg b/board/freescale/s32v234evb/s32v234evb.cfg
index 6017a40..6449ef2 100644
--- a/board/freescale/s32v234evb/s32v234evb.cfg
+++ b/board/freescale/s32v234evb/s32v234evb.cfg
@@ -5,7 +5,7 @@
*/
/*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/freescale/vf610twr/imximage.cfg b/board/freescale/vf610twr/imximage.cfg
index 9c823c4..09125cf 100644
--- a/board/freescale/vf610twr/imximage.cfg
+++ b/board/freescale/vf610twr/imximage.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/phytec/pcm052/imximage.cfg b/board/phytec/pcm052/imximage.cfg
index f5a9747..2fbb5c1b 100644
--- a/board/phytec/pcm052/imximage.cfg
+++ b/board/phytec/pcm052/imximage.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/technexion/pico-imx6ul/imximage.cfg b/board/technexion/pico-imx6ul/imximage.cfg
index 9145b44..c753a71 100644
--- a/board/technexion/pico-imx6ul/imximage.cfg
+++ b/board/technexion/pico-imx6ul/imximage.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/toradex/colibri_imx7/imximage.cfg b/board/toradex/colibri_imx7/imximage.cfg
index d891e82..ca3cd89 100644
--- a/board/toradex/colibri_imx7/imximage.cfg
+++ b/board/toradex/colibri_imx7/imximage.cfg
@@ -4,7 +4,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/toradex/colibri_vf/imximage.cfg b/board/toradex/colibri_vf/imximage.cfg
index 8c52886..baab812 100644
--- a/board/toradex/colibri_vf/imximage.cfg
+++ b/board/toradex/colibri_vf/imximage.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/warp/imximage.cfg b/board/warp/imximage.cfg
index 7b1d6b7..771dbb3 100644
--- a/board/warp/imximage.cfg
+++ b/board/warp/imximage.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0+
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
diff --git a/board/warp7/imximage.cfg b/board/warp7/imximage.cfg
index e7b6d30..5b42793 100644
--- a/board/warp7/imximage.cfg
+++ b/board/warp7/imximage.cfg
@@ -3,7 +3,7 @@
*
* SPDX-License-Identifier: GPL-2.0
*
- * Refer docs/README.imxmage for more details about how-to configure
+ * Refer doc/README.imximage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 08/21] arm: dts: Add devicetree for i.MX6DL
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (6 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 07/21] imx: s/docs\/README.imximage/doc\/README.imximage/g Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 09/21] arm: dts: Add devicetree for i.MX6DQL Jagan Teki
` (13 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add i.MX6DL dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/imx6dl.dtsi | 133 +++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 133 insertions(+)
create mode 100644 arch/arm/dts/imx6dl.dtsi
diff --git a/arch/arm/dts/imx6dl.dtsi b/arch/arm/dts/imx6dl.dtsi
new file mode 100644
index 0000000..9a4c22c
--- /dev/null
+++ b/arch/arm/dts/imx6dl.dtsi
@@ -0,0 +1,133 @@
+
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6dl-pinfunc.h"
+#include "imx6qdl.dtsi"
+
+/ {
+ aliases {
+ i2c3 = &i2c4;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1150000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC-PU uV */
+ 996000 1175000
+ 792000 1175000
+ 396000 1175000
+ >;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clks IMX6QDL_CLK_ARM>,
+ <&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
+ <&clks IMX6QDL_CLK_STEP>,
+ <&clks IMX6QDL_CLK_PLL1_SW>,
+ <&clks IMX6QDL_CLK_PLL1_SYS>;
+ clock-names = "arm", "pll2_pfd2_396m", "step",
+ "pll1_sw", "pll1_sys";
+ arm-supply = <®_arm>;
+ pu-supply = <®_pu>;
+ soc-supply = <®_soc>;
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ };
+ };
+
+ soc {
+ ocram: sram at 00900000 {
+ compatible = "mmio-sram";
+ reg = <0x00900000 0x20000>;
+ clocks = <&clks IMX6QDL_CLK_OCRAM>;
+ };
+
+ aips1: aips-bus at 02000000 {
+ iomuxc: iomuxc at 020e0000 {
+ compatible = "fsl,imx6dl-iomuxc";
+ };
+
+ pxp: pxp at 020f0000 {
+ reg = <0x020f0000 0x4000>;
+ interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ epdc: epdc at 020f4000 {
+ reg = <0x020f4000 0x4000>;
+ interrupts = <0 97 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ lcdif: lcdif at 020f8000 {
+ reg = <0x020f8000 0x4000>;
+ interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ aips2: aips-bus at 02100000 {
+ i2c4: i2c at 021f8000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c";
+ reg = <0x021f8000 0x4000>;
+ interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6DL_CLK_I2C4>;
+ status = "disabled";
+ };
+ };
+ };
+
+ display-subsystem {
+ compatible = "fsl,imx-display-subsystem";
+ ports = <&ipu1_di0>, <&ipu1_di1>;
+ };
+
+ gpu-subsystem {
+ compatible = "fsl,imx-gpu-subsystem";
+ cores = <&gpu_2d>, <&gpu_3d>;
+ };
+};
+
+&gpt {
+ compatible = "fsl,imx6dl-gpt";
+};
+
+&hdmi {
+ compatible = "fsl,imx6dl-hdmi";
+};
+
+&ldb {
+ clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+ <&clks IMX6QDL_CLK_IPU1_DI0_SEL>, <&clks IMX6QDL_CLK_IPU1_DI1_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI0>, <&clks IMX6QDL_CLK_LDB_DI1>;
+ clock-names = "di0_pll", "di1_pll",
+ "di0_sel", "di1_sel",
+ "di0", "di1";
+};
+
+&vpu {
+ compatible = "fsl,imx6dl-vpu", "cnm,coda960";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 09/21] arm: dts: Add devicetree for i.MX6DQL
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (7 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 08/21] arm: dts: Add devicetree for i.MX6DL Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 10/21] arm: dts: imx6dl: Add pinctrl defines Jagan Teki
` (12 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add i.MX6DQL dtsi support from Linux.
Here is the last commit:
"ARM: dts: imx6qdl: Fix SPDIF regression"
(sha1: f065e9e4addd75c21bb976bb2558648bf4f61de6)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/imx6qdl.dtsi | 1281 +++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 1281 insertions(+)
create mode 100644 arch/arm/dts/imx6qdl.dtsi
diff --git a/arch/arm/dts/imx6qdl.dtsi b/arch/arm/dts/imx6qdl.dtsi
new file mode 100644
index 0000000..b13b0b2
--- /dev/null
+++ b/arch/arm/dts/imx6qdl.dtsi
@@ -0,0 +1,1281 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#include "skeleton.dtsi"
+
+/ {
+ aliases {
+ ethernet0 = &fec;
+ can0 = &can1;
+ can1 = &can2;
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
+ gpio5 = &gpio6;
+ gpio6 = &gpio7;
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ ipu0 = &ipu1;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc3;
+ mmc3 = &usdhc4;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ spi0 = &ecspi1;
+ spi1 = &ecspi2;
+ spi2 = &ecspi3;
+ spi3 = &ecspi4;
+ usbphy0 = &usbphy1;
+ usbphy1 = &usbphy2;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ckil {
+ compatible = "fsl,imx-ckil", "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+
+ ckih1 {
+ compatible = "fsl,imx-ckih1", "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ };
+
+ osc {
+ compatible = "fsl,imx-osc", "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&gpc>;
+ ranges;
+
+ dma_apbh: dma-apbh at 00110000 {
+ compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
+ reg = <0x00110000 0x2000>;
+ interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,
+ <0 13 IRQ_TYPE_LEVEL_HIGH>,
+ <0 13 IRQ_TYPE_LEVEL_HIGH>,
+ <0 13 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+ #dma-cells = <1>;
+ dma-channels = <4>;
+ clocks = <&clks IMX6QDL_CLK_APBH_DMA>;
+ };
+
+ gpmi: gpmi-nand at 00112000 {
+ compatible = "fsl,imx6q-gpmi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x00112000 0x2000>, <0x00114000 0x2000>;
+ reg-names = "gpmi-nand", "bch";
+ interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "bch";
+ clocks = <&clks IMX6QDL_CLK_GPMI_IO>,
+ <&clks IMX6QDL_CLK_GPMI_APB>,
+ <&clks IMX6QDL_CLK_GPMI_BCH>,
+ <&clks IMX6QDL_CLK_GPMI_BCH_APB>,
+ <&clks IMX6QDL_CLK_PER1_BCH>;
+ clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch",
+ "gpmi_bch_apb", "per1_bch";
+ dmas = <&dma_apbh 0>;
+ dma-names = "rx-tx";
+ status = "disabled";
+ };
+
+ hdmi: hdmi at 0120000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x00120000 0x9000>;
+ interrupts = <0 115 0x04>;
+ gpr = <&gpr>;
+ clocks = <&clks IMX6QDL_CLK_HDMI_IAHB>,
+ <&clks IMX6QDL_CLK_HDMI_ISFR>;
+ clock-names = "iahb", "isfr";
+ status = "disabled";
+
+ port at 0 {
+ reg = <0>;
+
+ hdmi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_hdmi>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ hdmi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_hdmi>;
+ };
+ };
+ };
+
+ gpu_3d: gpu at 00130000 {
+ compatible = "vivante,gc";
+ reg = <0x00130000 0x4000>;
+ interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_GPU3D_AXI>,
+ <&clks IMX6QDL_CLK_GPU3D_CORE>,
+ <&clks IMX6QDL_CLK_GPU3D_SHADER>;
+ clock-names = "bus", "core", "shader";
+ power-domains = <&gpc 1>;
+ };
+
+ gpu_2d: gpu at 00134000 {
+ compatible = "vivante,gc";
+ reg = <0x00134000 0x4000>;
+ interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_GPU2D_AXI>,
+ <&clks IMX6QDL_CLK_GPU2D_CORE>;
+ clock-names = "bus", "core";
+ power-domains = <&gpc 1>;
+ };
+
+ timer at 00a00600 {
+ compatible = "arm,cortex-a9-twd-timer";
+ reg = <0x00a00600 0x20>;
+ interrupts = <1 13 0xf01>;
+ interrupt-parent = <&intc>;
+ clocks = <&clks IMX6QDL_CLK_TWD>;
+ };
+
+ intc: interrupt-controller at 00a01000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x00a01000 0x1000>,
+ <0x00a00100 0x100>;
+ interrupt-parent = <&intc>;
+ };
+
+ L2: l2-cache at 00a02000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x00a02000 0x1000>;
+ interrupts = <0 92 IRQ_TYPE_LEVEL_HIGH>;
+ cache-unified;
+ cache-level = <2>;
+ arm,tag-latency = <4 2 3>;
+ arm,data-latency = <4 2 3>;
+ arm,shared-override;
+ };
+
+ pcie: pcie at 0x01000000 {
+ compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
+ reg = <0x01ffc000 0x04000>,
+ <0x01f00000 0x80000>;
+ reg-names = "dbi", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */
+ 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
+ num-lanes = <1>;
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_PCIE_AXI>,
+ <&clks IMX6QDL_CLK_LVDS1_GATE>,
+ <&clks IMX6QDL_CLK_PCIE_REF_125M>;
+ clock-names = "pcie", "pcie_bus", "pcie_phy";
+ status = "disabled";
+ };
+
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ aips-bus at 02000000 { /* AIPS1 */
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02000000 0x100000>;
+ ranges;
+
+ spba-bus at 02000000 {
+ compatible = "fsl,spba-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02000000 0x40000>;
+ ranges;
+
+ spdif: spdif at 02004000 {
+ compatible = "fsl,imx35-spdif";
+ reg = <0x02004000 0x4000>;
+ interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&sdma 14 18 0>,
+ <&sdma 15 18 0>;
+ dma-names = "rx", "tx";
+ clocks = <&clks IMX6QDL_CLK_SPDIF_GCLK>, <&clks IMX6QDL_CLK_OSC>,
+ <&clks IMX6QDL_CLK_SPDIF>, <&clks IMX6QDL_CLK_ASRC>,
+ <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_ESAI_EXTAL>,
+ <&clks IMX6QDL_CLK_IPG>, <&clks IMX6QDL_CLK_DUMMY>,
+ <&clks IMX6QDL_CLK_DUMMY>, <&clks IMX6QDL_CLK_SPBA>;
+ clock-names = "core", "rxtx0",
+ "rxtx1", "rxtx2",
+ "rxtx3", "rxtx4",
+ "rxtx5", "rxtx6",
+ "rxtx7", "spba";
+ status = "disabled";
+ };
+
+ ecspi1: ecspi at 02008000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02008000 0x4000>;
+ interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_ECSPI1>,
+ <&clks IMX6QDL_CLK_ECSPI1>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 3 8 1>, <&sdma 4 8 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ecspi2: ecspi at 0200c000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
+ reg = <0x0200c000 0x4000>;
+ interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_ECSPI2>,
+ <&clks IMX6QDL_CLK_ECSPI2>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 5 8 1>, <&sdma 6 8 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ecspi3: ecspi at 02010000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02010000 0x4000>;
+ interrupts = <0 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_ECSPI3>,
+ <&clks IMX6QDL_CLK_ECSPI3>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 7 8 1>, <&sdma 8 8 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ecspi4: ecspi at 02014000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02014000 0x4000>;
+ interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_ECSPI4>,
+ <&clks IMX6QDL_CLK_ECSPI4>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 9 8 1>, <&sdma 10 8 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial at 02020000 {
+ compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+ reg = <0x02020000 0x4000>;
+ interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_UART_IPG>,
+ <&clks IMX6QDL_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 25 4 0>, <&sdma 26 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ esai: esai at 02024000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,imx35-esai";
+ reg = <0x02024000 0x4000>;
+ interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_ESAI_IPG>,
+ <&clks IMX6QDL_CLK_ESAI_MEM>,
+ <&clks IMX6QDL_CLK_ESAI_EXTAL>,
+ <&clks IMX6QDL_CLK_ESAI_IPG>,
+ <&clks IMX6QDL_CLK_SPBA>;
+ clock-names = "core", "mem", "extal", "fsys", "spba";
+ dmas = <&sdma 23 21 0>, <&sdma 24 21 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ ssi1: ssi at 02028000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,imx6q-ssi",
+ "fsl,imx51-ssi";
+ reg = <0x02028000 0x4000>;
+ interrupts = <0 46 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_SSI1_IPG>,
+ <&clks IMX6QDL_CLK_SSI1>;
+ clock-names = "ipg", "baud";
+ dmas = <&sdma 37 1 0>,
+ <&sdma 38 1 0>;
+ dma-names = "rx", "tx";
+ fsl,fifo-depth = <15>;
+ status = "disabled";
+ };
+
+ ssi2: ssi at 0202c000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,imx6q-ssi",
+ "fsl,imx51-ssi";
+ reg = <0x0202c000 0x4000>;
+ interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_SSI2_IPG>,
+ <&clks IMX6QDL_CLK_SSI2>;
+ clock-names = "ipg", "baud";
+ dmas = <&sdma 41 1 0>,
+ <&sdma 42 1 0>;
+ dma-names = "rx", "tx";
+ fsl,fifo-depth = <15>;
+ status = "disabled";
+ };
+
+ ssi3: ssi at 02030000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,imx6q-ssi",
+ "fsl,imx51-ssi";
+ reg = <0x02030000 0x4000>;
+ interrupts = <0 48 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_SSI3_IPG>,
+ <&clks IMX6QDL_CLK_SSI3>;
+ clock-names = "ipg", "baud";
+ dmas = <&sdma 45 1 0>,
+ <&sdma 46 1 0>;
+ dma-names = "rx", "tx";
+ fsl,fifo-depth = <15>;
+ status = "disabled";
+ };
+
+ asrc: asrc at 02034000 {
+ compatible = "fsl,imx53-asrc";
+ reg = <0x02034000 0x4000>;
+ interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_ASRC_IPG>,
+ <&clks IMX6QDL_CLK_ASRC_MEM>, <&clks 0>,
+ <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+ <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+ <&clks 0>, <&clks 0>, <&clks 0>, <&clks 0>,
+ <&clks IMX6QDL_CLK_ASRC>, <&clks 0>, <&clks 0>,
+ <&clks IMX6QDL_CLK_SPBA>;
+ clock-names = "mem", "ipg", "asrck_0",
+ "asrck_1", "asrck_2", "asrck_3", "asrck_4",
+ "asrck_5", "asrck_6", "asrck_7", "asrck_8",
+ "asrck_9", "asrck_a", "asrck_b", "asrck_c",
+ "asrck_d", "asrck_e", "asrck_f", "spba";
+ dmas = <&sdma 17 23 1>, <&sdma 18 23 1>, <&sdma 19 23 1>,
+ <&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>;
+ dma-names = "rxa", "rxb", "rxc",
+ "txa", "txb", "txc";
+ fsl,asrc-rate = <48000>;
+ fsl,asrc-width = <16>;
+ status = "okay";
+ };
+
+ spba at 0203c000 {
+ reg = <0x0203c000 0x4000>;
+ };
+ };
+
+ vpu: vpu at 02040000 {
+ compatible = "cnm,coda960";
+ reg = <0x02040000 0x3c000>;
+ interrupts = <0 12 IRQ_TYPE_LEVEL_HIGH>,
+ <0 3 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "bit", "jpeg";
+ clocks = <&clks IMX6QDL_CLK_VPU_AXI>,
+ <&clks IMX6QDL_CLK_MMDC_CH0_AXI>;
+ clock-names = "per", "ahb";
+ power-domains = <&gpc 1>;
+ resets = <&src 1>;
+ iram = <&ocram>;
+ };
+
+ aipstz at 0207c000 { /* AIPSTZ1 */
+ reg = <0x0207c000 0x4000>;
+ };
+
+ pwm1: pwm at 02080000 {
+ #pwm-cells = <2>;
+ compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
+ reg = <0x02080000 0x4000>;
+ interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_IPG>,
+ <&clks IMX6QDL_CLK_PWM1>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ pwm2: pwm at 02084000 {
+ #pwm-cells = <2>;
+ compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
+ reg = <0x02084000 0x4000>;
+ interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_IPG>,
+ <&clks IMX6QDL_CLK_PWM2>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ pwm3: pwm at 02088000 {
+ #pwm-cells = <2>;
+ compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
+ reg = <0x02088000 0x4000>;
+ interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_IPG>,
+ <&clks IMX6QDL_CLK_PWM3>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ pwm4: pwm at 0208c000 {
+ #pwm-cells = <2>;
+ compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm";
+ reg = <0x0208c000 0x4000>;
+ interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_IPG>,
+ <&clks IMX6QDL_CLK_PWM4>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ can1: flexcan at 02090000 {
+ compatible = "fsl,imx6q-flexcan";
+ reg = <0x02090000 0x4000>;
+ interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_CAN1_IPG>,
+ <&clks IMX6QDL_CLK_CAN1_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ can2: flexcan at 02094000 {
+ compatible = "fsl,imx6q-flexcan";
+ reg = <0x02094000 0x4000>;
+ interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_CAN2_IPG>,
+ <&clks IMX6QDL_CLK_CAN2_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ gpt: gpt at 02098000 {
+ compatible = "fsl,imx6q-gpt", "fsl,imx31-gpt";
+ reg = <0x02098000 0x4000>;
+ interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_GPT_IPG>,
+ <&clks IMX6QDL_CLK_GPT_IPG_PER>,
+ <&clks IMX6QDL_CLK_GPT_3M>;
+ clock-names = "ipg", "per", "osc_per";
+ };
+
+ gpio1: gpio at 0209c000 {
+ compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
+ reg = <0x0209c000 0x4000>;
+ interrupts = <0 66 IRQ_TYPE_LEVEL_HIGH>,
+ <0 67 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio at 020a0000 {
+ compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
+ reg = <0x020a0000 0x4000>;
+ interrupts = <0 68 IRQ_TYPE_LEVEL_HIGH>,
+ <0 69 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio at 020a4000 {
+ compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
+ reg = <0x020a4000 0x4000>;
+ interrupts = <0 70 IRQ_TYPE_LEVEL_HIGH>,
+ <0 71 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio at 020a8000 {
+ compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
+ reg = <0x020a8000 0x4000>;
+ interrupts = <0 72 IRQ_TYPE_LEVEL_HIGH>,
+ <0 73 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio5: gpio at 020ac000 {
+ compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
+ reg = <0x020ac000 0x4000>;
+ interrupts = <0 74 IRQ_TYPE_LEVEL_HIGH>,
+ <0 75 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio6: gpio at 020b0000 {
+ compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
+ reg = <0x020b0000 0x4000>;
+ interrupts = <0 76 IRQ_TYPE_LEVEL_HIGH>,
+ <0 77 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio7: gpio at 020b4000 {
+ compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio";
+ reg = <0x020b4000 0x4000>;
+ interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>,
+ <0 79 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ kpp: kpp at 020b8000 {
+ compatible = "fsl,imx6q-kpp", "fsl,imx21-kpp";
+ reg = <0x020b8000 0x4000>;
+ interrupts = <0 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_IPG>;
+ status = "disabled";
+ };
+
+ wdog1: wdog at 020bc000 {
+ compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
+ reg = <0x020bc000 0x4000>;
+ interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_DUMMY>;
+ };
+
+ wdog2: wdog at 020c0000 {
+ compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
+ reg = <0x020c0000 0x4000>;
+ interrupts = <0 81 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_DUMMY>;
+ status = "disabled";
+ };
+
+ clks: ccm at 020c4000 {
+ compatible = "fsl,imx6q-ccm";
+ reg = <0x020c4000 0x4000>;
+ interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>,
+ <0 88 IRQ_TYPE_LEVEL_HIGH>;
+ #clock-cells = <1>;
+ };
+
+ anatop: anatop at 020c8000 {
+ compatible = "fsl,imx6q-anatop", "syscon", "simple-bus";
+ reg = <0x020c8000 0x1000>;
+ interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>,
+ <0 54 IRQ_TYPE_LEVEL_HIGH>,
+ <0 127 IRQ_TYPE_LEVEL_HIGH>;
+
+ regulator-1p1 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd1p1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1375000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x110>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <4>;
+ anatop-min-voltage = <800000>;
+ anatop-max-voltage = <1375000>;
+ };
+
+ regulator-3p0 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd3p0";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x120>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <0>;
+ anatop-min-voltage = <2625000>;
+ anatop-max-voltage = <3400000>;
+ };
+
+ regulator-2p5 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd2p5";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2750000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x130>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <0>;
+ anatop-min-voltage = <2000000>;
+ anatop-max-voltage = <2750000>;
+ };
+
+ reg_arm: regulator-vddcore {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vddarm";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <0>;
+ anatop-vol-bit-width = <5>;
+ anatop-delay-reg-offset = <0x170>;
+ anatop-delay-bit-shift = <24>;
+ anatop-delay-bit-width = <2>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
+
+ reg_pu: regulator-vddpu {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vddpu";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-enable-ramp-delay = <150>;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <9>;
+ anatop-vol-bit-width = <5>;
+ anatop-delay-reg-offset = <0x170>;
+ anatop-delay-bit-shift = <26>;
+ anatop-delay-bit-width = <2>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
+
+ reg_soc: regulator-vddsoc {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vddsoc";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <18>;
+ anatop-vol-bit-width = <5>;
+ anatop-delay-reg-offset = <0x170>;
+ anatop-delay-bit-shift = <28>;
+ anatop-delay-bit-width = <2>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
+ };
+
+ tempmon: tempmon {
+ compatible = "fsl,imx6q-tempmon";
+ interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>;
+ fsl,tempmon = <&anatop>;
+ fsl,tempmon-data = <&ocotp>;
+ clocks = <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+ };
+
+ usbphy1: usbphy at 020c9000 {
+ compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy";
+ reg = <0x020c9000 0x1000>;
+ interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USBPHY1>;
+ fsl,anatop = <&anatop>;
+ };
+
+ usbphy2: usbphy at 020ca000 {
+ compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy";
+ reg = <0x020ca000 0x1000>;
+ interrupts = <0 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USBPHY2>;
+ fsl,anatop = <&anatop>;
+ };
+
+ snvs: snvs at 020cc000 {
+ compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
+ reg = <0x020cc000 0x4000>;
+
+ snvs_rtc: snvs-rtc-lp {
+ compatible = "fsl,sec-v4.0-mon-rtc-lp";
+ regmap = <&snvs>;
+ offset = <0x34>;
+ interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>,
+ <0 20 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ snvs_poweroff: snvs-poweroff {
+ compatible = "syscon-poweroff";
+ regmap = <&snvs>;
+ offset = <0x38>;
+ mask = <0x60>;
+ status = "disabled";
+ };
+ };
+
+ epit1: epit at 020d0000 { /* EPIT1 */
+ reg = <0x020d0000 0x4000>;
+ interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ epit2: epit at 020d4000 { /* EPIT2 */
+ reg = <0x020d4000 0x4000>;
+ interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ src: src at 020d8000 {
+ compatible = "fsl,imx6q-src", "fsl,imx51-src";
+ reg = <0x020d8000 0x4000>;
+ interrupts = <0 91 IRQ_TYPE_LEVEL_HIGH>,
+ <0 96 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ };
+
+ gpc: gpc at 020dc000 {
+ compatible = "fsl,imx6q-gpc";
+ reg = <0x020dc000 0x4000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>,
+ <0 90 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&intc>;
+ pu-supply = <®_pu>;
+ clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>,
+ <&clks IMX6QDL_CLK_GPU3D_SHADER>,
+ <&clks IMX6QDL_CLK_GPU2D_CORE>,
+ <&clks IMX6QDL_CLK_GPU2D_AXI>,
+ <&clks IMX6QDL_CLK_OPENVG_AXI>,
+ <&clks IMX6QDL_CLK_VPU_AXI>;
+ #power-domain-cells = <1>;
+ };
+
+ gpr: iomuxc-gpr at 020e0000 {
+ compatible = "fsl,imx6q-iomuxc-gpr", "syscon";
+ reg = <0x020e0000 0x38>;
+ };
+
+ iomuxc: iomuxc at 020e0000 {
+ compatible = "fsl,imx6dl-iomuxc", "fsl,imx6q-iomuxc";
+ reg = <0x020e0000 0x4000>;
+ };
+
+ ldb: ldb at 020e0008 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ldb", "fsl,imx53-ldb";
+ gpr = <&gpr>;
+ status = "disabled";
+
+ lvds-channel at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ status = "disabled";
+
+ port at 0 {
+ reg = <0>;
+
+ lvds0_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_lvds0>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ lvds0_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_lvds0>;
+ };
+ };
+ };
+
+ lvds-channel at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ status = "disabled";
+
+ port at 0 {
+ reg = <0>;
+
+ lvds1_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_lvds1>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ lvds1_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_lvds1>;
+ };
+ };
+ };
+ };
+
+ dcic1: dcic at 020e4000 {
+ reg = <0x020e4000 0x4000>;
+ interrupts = <0 124 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ dcic2: dcic at 020e8000 {
+ reg = <0x020e8000 0x4000>;
+ interrupts = <0 125 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ sdma: sdma at 020ec000 {
+ compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma";
+ reg = <0x020ec000 0x4000>;
+ interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_SDMA>,
+ <&clks IMX6QDL_CLK_SDMA>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin";
+ };
+ };
+
+ aips-bus at 02100000 { /* AIPS2 */
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02100000 0x100000>;
+ ranges;
+
+ crypto: caam at 2100000 {
+ compatible = "fsl,sec-v4.0";
+ fsl,sec-era = <4>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x2100000 0x10000>;
+ ranges = <0 0x2100000 0x10000>;
+ clocks = <&clks IMX6QDL_CLK_CAAM_MEM>,
+ <&clks IMX6QDL_CLK_CAAM_ACLK>,
+ <&clks IMX6QDL_CLK_CAAM_IPG>,
+ <&clks IMX6QDL_CLK_EIM_SLOW>;
+ clock-names = "mem", "aclk", "ipg", "emi_slow";
+
+ sec_jr0: jr0 at 1000 {
+ compatible = "fsl,sec-v4.0-job-ring";
+ reg = <0x1000 0x1000>;
+ interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ sec_jr1: jr1 at 2000 {
+ compatible = "fsl,sec-v4.0-job-ring";
+ reg = <0x2000 0x1000>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ aipstz at 0217c000 { /* AIPSTZ2 */
+ reg = <0x0217c000 0x4000>;
+ };
+
+ usbotg: usb at 02184000 {
+ compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
+ reg = <0x02184000 0x200>;
+ interrupts = <0 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ fsl,usbphy = <&usbphy1>;
+ fsl,usbmisc = <&usbmisc 0>;
+ ahb-burst-config = <0x0>;
+ tx-burst-size-dword = <0x10>;
+ rx-burst-size-dword = <0x10>;
+ status = "disabled";
+ };
+
+ usbh1: usb at 02184200 {
+ compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
+ reg = <0x02184200 0x200>;
+ interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ fsl,usbphy = <&usbphy2>;
+ fsl,usbmisc = <&usbmisc 1>;
+ dr_mode = "host";
+ ahb-burst-config = <0x0>;
+ tx-burst-size-dword = <0x10>;
+ rx-burst-size-dword = <0x10>;
+ status = "disabled";
+ };
+
+ usbh2: usb at 02184400 {
+ compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
+ reg = <0x02184400 0x200>;
+ interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ fsl,usbmisc = <&usbmisc 2>;
+ dr_mode = "host";
+ ahb-burst-config = <0x0>;
+ tx-burst-size-dword = <0x10>;
+ rx-burst-size-dword = <0x10>;
+ status = "disabled";
+ };
+
+ usbh3: usb at 02184600 {
+ compatible = "fsl,imx6q-usb", "fsl,imx27-usb";
+ reg = <0x02184600 0x200>;
+ interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ fsl,usbmisc = <&usbmisc 3>;
+ dr_mode = "host";
+ ahb-burst-config = <0x0>;
+ tx-burst-size-dword = <0x10>;
+ rx-burst-size-dword = <0x10>;
+ status = "disabled";
+ };
+
+ usbmisc: usbmisc at 02184800 {
+ #index-cells = <1>;
+ compatible = "fsl,imx6q-usbmisc";
+ reg = <0x02184800 0x200>;
+ clocks = <&clks IMX6QDL_CLK_USBOH3>;
+ };
+
+ fec: ethernet at 02188000 {
+ compatible = "fsl,imx6q-fec";
+ reg = <0x02188000 0x4000>;
+ interrupts-extended =
+ <&intc 0 118 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET>,
+ <&clks IMX6QDL_CLK_ENET_REF>;
+ clock-names = "ipg", "ahb", "ptp";
+ status = "disabled";
+ };
+
+ mlb at 0218c000 {
+ reg = <0x0218c000 0x4000>;
+ interrupts = <0 53 IRQ_TYPE_LEVEL_HIGH>,
+ <0 117 IRQ_TYPE_LEVEL_HIGH>,
+ <0 126 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ usdhc1: usdhc at 02190000 {
+ compatible = "fsl,imx6q-usdhc";
+ reg = <0x02190000 0x4000>;
+ interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USDHC1>,
+ <&clks IMX6QDL_CLK_USDHC1>,
+ <&clks IMX6QDL_CLK_USDHC1>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc2: usdhc at 02194000 {
+ compatible = "fsl,imx6q-usdhc";
+ reg = <0x02194000 0x4000>;
+ interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USDHC2>,
+ <&clks IMX6QDL_CLK_USDHC2>,
+ <&clks IMX6QDL_CLK_USDHC2>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc3: usdhc at 02198000 {
+ compatible = "fsl,imx6q-usdhc";
+ reg = <0x02198000 0x4000>;
+ interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USDHC3>,
+ <&clks IMX6QDL_CLK_USDHC3>,
+ <&clks IMX6QDL_CLK_USDHC3>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc4: usdhc at 0219c000 {
+ compatible = "fsl,imx6q-usdhc";
+ reg = <0x0219c000 0x4000>;
+ interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_USDHC4>,
+ <&clks IMX6QDL_CLK_USDHC4>,
+ <&clks IMX6QDL_CLK_USDHC4>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at 021a0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c";
+ reg = <0x021a0000 0x4000>;
+ interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_I2C1>;
+ status = "disabled";
+ };
+
+ i2c2: i2c at 021a4000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c";
+ reg = <0x021a4000 0x4000>;
+ interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_I2C2>;
+ status = "disabled";
+ };
+
+ i2c3: i2c at 021a8000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c";
+ reg = <0x021a8000 0x4000>;
+ interrupts = <0 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_I2C3>;
+ status = "disabled";
+ };
+
+ romcp at 021ac000 {
+ reg = <0x021ac000 0x4000>;
+ };
+
+ mmdc0: mmdc at 021b0000 { /* MMDC0 */
+ compatible = "fsl,imx6q-mmdc";
+ reg = <0x021b0000 0x4000>;
+ };
+
+ mmdc1: mmdc at 021b4000 { /* MMDC1 */
+ reg = <0x021b4000 0x4000>;
+ };
+
+ weim: weim at 021b8000 {
+ compatible = "fsl,imx6q-weim";
+ reg = <0x021b8000 0x4000>;
+ interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_EIM_SLOW>;
+ };
+
+ ocotp: ocotp at 021bc000 {
+ compatible = "fsl,imx6q-ocotp", "syscon";
+ reg = <0x021bc000 0x4000>;
+ clocks = <&clks IMX6QDL_CLK_IIM>;
+ };
+
+ tzasc at 021d0000 { /* TZASC1 */
+ reg = <0x021d0000 0x4000>;
+ interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ tzasc at 021d4000 { /* TZASC2 */
+ reg = <0x021d4000 0x4000>;
+ interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ audmux: audmux at 021d8000 {
+ compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux";
+ reg = <0x021d8000 0x4000>;
+ status = "disabled";
+ };
+
+ mipi_csi: mipi at 021dc000 {
+ reg = <0x021dc000 0x4000>;
+ };
+
+ mipi_dsi: mipi at 021e0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x021e0000 0x4000>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+
+ mipi_mux_0: endpoint {
+ remote-endpoint = <&ipu1_di0_mipi>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ mipi_mux_1: endpoint {
+ remote-endpoint = <&ipu1_di1_mipi>;
+ };
+ };
+ };
+ };
+
+ vdoa at 021e4000 {
+ reg = <0x021e4000 0x4000>;
+ interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ uart2: serial at 021e8000 {
+ compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+ reg = <0x021e8000 0x4000>;
+ interrupts = <0 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_UART_IPG>,
+ <&clks IMX6QDL_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 27 4 0>, <&sdma 28 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial at 021ec000 {
+ compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+ reg = <0x021ec000 0x4000>;
+ interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_UART_IPG>,
+ <&clks IMX6QDL_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 29 4 0>, <&sdma 30 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart4: serial at 021f0000 {
+ compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+ reg = <0x021f0000 0x4000>;
+ interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_UART_IPG>,
+ <&clks IMX6QDL_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 31 4 0>, <&sdma 32 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart5: serial at 021f4000 {
+ compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+ reg = <0x021f4000 0x4000>;
+ interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_UART_IPG>,
+ <&clks IMX6QDL_CLK_UART_SERIAL>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 33 4 0>, <&sdma 34 4 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+ };
+
+ ipu1: ipu at 02400000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ipu";
+ reg = <0x02400000 0x400000>;
+ interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>,
+ <0 5 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_IPU1>,
+ <&clks IMX6QDL_CLK_IPU1_DI0>,
+ <&clks IMX6QDL_CLK_IPU1_DI1>;
+ clock-names = "bus", "di0", "di1";
+ resets = <&src 2>;
+
+ ipu1_csi0: port at 0 {
+ reg = <0>;
+ };
+
+ ipu1_csi1: port at 1 {
+ reg = <1>;
+ };
+
+ ipu1_di0: port at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ ipu1_di0_disp0: disp0-endpoint {
+ };
+
+ ipu1_di0_hdmi: hdmi-endpoint {
+ remote-endpoint = <&hdmi_mux_0>;
+ };
+
+ ipu1_di0_mipi: mipi-endpoint {
+ remote-endpoint = <&mipi_mux_0>;
+ };
+
+ ipu1_di0_lvds0: lvds0-endpoint {
+ remote-endpoint = <&lvds0_mux_0>;
+ };
+
+ ipu1_di0_lvds1: lvds1-endpoint {
+ remote-endpoint = <&lvds1_mux_0>;
+ };
+ };
+
+ ipu1_di1: port at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ ipu1_di1_disp1: disp1-endpoint {
+ };
+
+ ipu1_di1_hdmi: hdmi-endpoint {
+ remote-endpoint = <&hdmi_mux_1>;
+ };
+
+ ipu1_di1_mipi: mipi-endpoint {
+ remote-endpoint = <&mipi_mux_1>;
+ };
+
+ ipu1_di1_lvds0: lvds0-endpoint {
+ remote-endpoint = <&lvds0_mux_1>;
+ };
+
+ ipu1_di1_lvds1: lvds1-endpoint {
+ remote-endpoint = <&lvds1_mux_1>;
+ };
+ };
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 10/21] arm: dts: imx6dl: Add pinctrl defines
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (8 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 09/21] arm: dts: Add devicetree for i.MX6DQL Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 11/21] dt-bindings: clock: imx6qdl: Add clock defines Jagan Teki
` (11 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add imx6dl pinctrl defines support from Linux.
Here is the last commit:
"ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ"
(sha1: d8c765e0d1ddbd5032c2491c82cc9660c2f0e7f2)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/imx6dl-pinfunc.h | 1091 +++++++++++++++++++++++++++++++++++++++++
1 file changed, 1091 insertions(+)
create mode 100644 arch/arm/dts/imx6dl-pinfunc.h
diff --git a/arch/arm/dts/imx6dl-pinfunc.h b/arch/arm/dts/imx6dl-pinfunc.h
new file mode 100644
index 0000000..0ead323
--- /dev/null
+++ b/arch/arm/dts/imx6dl-pinfunc.h
@@ -0,0 +1,1091 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __DTS_IMX6DL_PINFUNC_H
+#define __DTS_IMX6DL_PINFUNC_H
+
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+#define MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10 0x04c 0x360 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT10__AUD3_RXC 0x04c 0x360 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO 0x04c 0x360 0x7f8 0x2 0x0
+#define MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x04c 0x360 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT10__UART1_RX_DATA 0x04c 0x360 0x8fc 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x04c 0x360 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT10__ARM_TRACE07 0x04c 0x360 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11 0x050 0x364 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT11__AUD3_RXFS 0x050 0x364 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT11__ECSPI2_SS0 0x050 0x364 0x800 0x2 0x0
+#define MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x050 0x364 0x8fc 0x3 0x1
+#define MX6QDL_PAD_CSI0_DAT11__UART1_TX_DATA 0x050 0x364 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x050 0x364 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT11__ARM_TRACE08 0x050 0x364 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x054 0x368 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x054 0x368 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x054 0x368 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT12__UART4_RX_DATA 0x054 0x368 0x914 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT12__GPIO5_IO30 0x054 0x368 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT12__ARM_TRACE09 0x054 0x368 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x058 0x36c 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x058 0x36c 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x058 0x36c 0x914 0x3 0x1
+#define MX6QDL_PAD_CSI0_DAT13__UART4_TX_DATA 0x058 0x36c 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31 0x058 0x36c 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT13__ARM_TRACE10 0x058 0x36c 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x05c 0x370 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x05c 0x370 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x05c 0x370 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT14__UART5_RX_DATA 0x05c 0x370 0x91c 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00 0x05c 0x370 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT14__ARM_TRACE11 0x05c 0x370 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x060 0x374 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x060 0x374 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x060 0x374 0x91c 0x3 0x1
+#define MX6QDL_PAD_CSI0_DAT15__UART5_TX_DATA 0x060 0x374 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT15__GPIO6_IO01 0x060 0x374 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT15__ARM_TRACE12 0x060 0x374 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x064 0x378 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x064 0x378 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x064 0x378 0x910 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT16__UART4_CTS_B 0x064 0x378 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT16__GPIO6_IO02 0x064 0x378 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT16__ARM_TRACE13 0x064 0x378 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x068 0x37c 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x068 0x37c 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x068 0x37c 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT17__UART4_RTS_B 0x068 0x37c 0x910 0x3 0x1
+#define MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x068 0x37c 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT17__ARM_TRACE14 0x068 0x37c 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x06c 0x380 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x06c 0x380 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B 0x06c 0x380 0x918 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT18__UART5_CTS_B 0x06c 0x380 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04 0x06c 0x380 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT18__ARM_TRACE15 0x06c 0x380 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x070 0x384 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x070 0x384 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x070 0x384 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT19__UART5_RTS_B 0x070 0x384 0x918 0x3 0x1
+#define MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05 0x070 0x384 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04 0x074 0x388 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x074 0x388 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT4__ECSPI1_SCLK 0x074 0x388 0x7d8 0x2 0x0
+#define MX6QDL_PAD_CSI0_DAT4__KEY_COL5 0x074 0x388 0x8c0 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x074 0x388 0x000 0x4 0x0
+#define MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x074 0x388 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT4__ARM_TRACE01 0x074 0x388 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05 0x078 0x38c 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x078 0x38c 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT5__ECSPI1_MOSI 0x078 0x38c 0x7e0 0x2 0x0
+#define MX6QDL_PAD_CSI0_DAT5__KEY_ROW5 0x078 0x38c 0x8cc 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x078 0x38c 0x000 0x4 0x0
+#define MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x078 0x38c 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT5__ARM_TRACE02 0x078 0x38c 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06 0x07c 0x390 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x07c 0x390 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT6__ECSPI1_MISO 0x07c 0x390 0x7dc 0x2 0x0
+#define MX6QDL_PAD_CSI0_DAT6__KEY_COL6 0x07c 0x390 0x8c4 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x07c 0x390 0x000 0x4 0x0
+#define MX6QDL_PAD_CSI0_DAT6__GPIO5_IO24 0x07c 0x390 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT6__ARM_TRACE03 0x07c 0x390 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07 0x080 0x394 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x080 0x394 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT7__ECSPI1_SS0 0x080 0x394 0x7e4 0x2 0x0
+#define MX6QDL_PAD_CSI0_DAT7__KEY_ROW6 0x080 0x394 0x8d0 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x080 0x394 0x000 0x4 0x0
+#define MX6QDL_PAD_CSI0_DAT7__GPIO5_IO25 0x080 0x394 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT7__ARM_TRACE04 0x080 0x394 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08 0x084 0x398 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x084 0x398 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK 0x084 0x398 0x7f4 0x2 0x0
+#define MX6QDL_PAD_CSI0_DAT8__KEY_COL7 0x084 0x398 0x8c8 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x084 0x398 0x86c 0x4 0x0
+#define MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x084 0x398 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT8__ARM_TRACE05 0x084 0x398 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09 0x088 0x39c 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x088 0x39c 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI 0x088 0x39c 0x7fc 0x2 0x0
+#define MX6QDL_PAD_CSI0_DAT9__KEY_ROW7 0x088 0x39c 0x8d4 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x088 0x39c 0x868 0x4 0x0
+#define MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x088 0x39c 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT9__ARM_TRACE06 0x088 0x39c 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x08c 0x3a0 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x08c 0x3a0 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x08c 0x3a0 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DATA_EN__ARM_TRACE_CLK 0x08c 0x3a0 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x090 0x3a4 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x090 0x3a4 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x090 0x3a4 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_MCLK__ARM_TRACE_CTL 0x090 0x3a4 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x094 0x3a8 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x094 0x3a8 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_PIXCLK__ARM_EVENTO 0x094 0x3a8 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x098 0x3ac 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x098 0x3ac 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x098 0x3ac 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_VSYNC__ARM_TRACE00 0x098 0x3ac 0x000 0x7 0x0
+#define MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x09c 0x3b0 0x000 0x0 0x0
+#define MX6QDL_PAD_DI0_DISP_CLK__LCD_CLK 0x09c 0x3b0 0x000 0x1 0x0
+#define MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x09c 0x3b0 0x000 0x5 0x0
+#define MX6QDL_PAD_DI0_DISP_CLK__LCD_WR_RWN 0x09c 0x3b0 0x000 0x8 0x0
+#define MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x0a0 0x3b4 0x000 0x0 0x0
+#define MX6QDL_PAD_DI0_PIN15__LCD_ENABLE 0x0a0 0x3b4 0x000 0x1 0x0
+#define MX6QDL_PAD_DI0_PIN15__AUD6_TXC 0x0a0 0x3b4 0x000 0x2 0x0
+#define MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x0a0 0x3b4 0x000 0x5 0x0
+#define MX6QDL_PAD_DI0_PIN15__LCD_RD_E 0x0a0 0x3b4 0x000 0x8 0x0
+#define MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x0a4 0x3b8 0x000 0x0 0x0
+#define MX6QDL_PAD_DI0_PIN2__LCD_HSYNC 0x0a4 0x3b8 0x8d8 0x1 0x0
+#define MX6QDL_PAD_DI0_PIN2__AUD6_TXD 0x0a4 0x3b8 0x000 0x2 0x0
+#define MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x0a4 0x3b8 0x000 0x5 0x0
+#define MX6QDL_PAD_DI0_PIN2__LCD_RS 0x0a4 0x3b8 0x000 0x8 0x0
+#define MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x0a8 0x3bc 0x000 0x0 0x0
+#define MX6QDL_PAD_DI0_PIN3__LCD_VSYNC 0x0a8 0x3bc 0x000 0x1 0x0
+#define MX6QDL_PAD_DI0_PIN3__AUD6_TXFS 0x0a8 0x3bc 0x000 0x2 0x0
+#define MX6QDL_PAD_DI0_PIN3__GPIO4_IO19 0x0a8 0x3bc 0x000 0x5 0x0
+#define MX6QDL_PAD_DI0_PIN3__LCD_CS 0x0a8 0x3bc 0x000 0x8 0x0
+#define MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04 0x0ac 0x3c0 0x000 0x0 0x0
+#define MX6QDL_PAD_DI0_PIN4__LCD_BUSY 0x0ac 0x3c0 0x8d8 0x1 0x1
+#define MX6QDL_PAD_DI0_PIN4__AUD6_RXD 0x0ac 0x3c0 0x000 0x2 0x0
+#define MX6QDL_PAD_DI0_PIN4__SD1_WP 0x0ac 0x3c0 0x92c 0x3 0x0
+#define MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x0ac 0x3c0 0x000 0x5 0x0
+#define MX6QDL_PAD_DI0_PIN4__LCD_RESET 0x0ac 0x3c0 0x000 0x8 0x0
+#define MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x0b0 0x3c4 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT0__LCD_DATA00 0x0b0 0x3c4 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x0b0 0x3c4 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x0b0 0x3c4 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x0b4 0x3c8 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT1__LCD_DATA01 0x0b4 0x3c8 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x0b4 0x3c8 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x0b4 0x3c8 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x0b8 0x3cc 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT10__LCD_DATA10 0x0b8 0x3cc 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31 0x0b8 0x3cc 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x0bc 0x3d0 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT11__LCD_DATA11 0x0bc 0x3d0 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x0bc 0x3d0 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x0c0 0x3d4 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT12__LCD_DATA12 0x0c0 0x3d4 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT12__GPIO5_IO06 0x0c0 0x3d4 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x0c4 0x3d8 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT13__LCD_DATA13 0x0c4 0x3d8 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT13__AUD5_RXFS 0x0c4 0x3d8 0x7bc 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x0c4 0x3d8 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x0c8 0x3dc 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT14__LCD_DATA14 0x0c8 0x3dc 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT14__AUD5_RXC 0x0c8 0x3dc 0x7b8 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x0c8 0x3dc 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x0cc 0x3e0 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT15__LCD_DATA15 0x0cc 0x3e0 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT15__ECSPI1_SS1 0x0cc 0x3e0 0x7e8 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT15__ECSPI2_SS1 0x0cc 0x3e0 0x804 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x0cc 0x3e0 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x0d0 0x3e4 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT16__LCD_DATA16 0x0d0 0x3e4 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x0d0 0x3e4 0x7fc 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT16__AUD5_TXC 0x0d0 0x3e4 0x7c0 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT16__SDMA_EXT_EVENT0 0x0d0 0x3e4 0x8e8 0x4 0x0
+#define MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x0d0 0x3e4 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x0d4 0x3e8 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT17__LCD_DATA17 0x0d4 0x3e8 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO 0x0d4 0x3e8 0x7f8 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT17__AUD5_TXD 0x0d4 0x3e8 0x7b4 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT17__SDMA_EXT_EVENT1 0x0d4 0x3e8 0x8ec 0x4 0x0
+#define MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x0d4 0x3e8 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x0d8 0x3ec 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT18__LCD_DATA18 0x0d8 0x3ec 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT18__ECSPI2_SS0 0x0d8 0x3ec 0x800 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS 0x0d8 0x3ec 0x7c4 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT18__AUD4_RXFS 0x0d8 0x3ec 0x7a4 0x4 0x0
+#define MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x0d8 0x3ec 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT18__EIM_CS2_B 0x0d8 0x3ec 0x000 0x7 0x0
+#define MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x0dc 0x3f0 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT19__LCD_DATA19 0x0dc 0x3f0 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK 0x0dc 0x3f0 0x7f4 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x0dc 0x3f0 0x7b0 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT19__AUD4_RXC 0x0dc 0x3f0 0x7a0 0x4 0x0
+#define MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x0dc 0x3f0 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT19__EIM_CS3_B 0x0dc 0x3f0 0x000 0x7 0x0
+#define MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x0e0 0x3f4 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT2__LCD_DATA02 0x0e0 0x3f4 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x0e0 0x3f4 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x0e0 0x3f4 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x0e4 0x3f8 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT20__LCD_DATA20 0x0e4 0x3f8 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT20__ECSPI1_SCLK 0x0e4 0x3f8 0x7d8 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x0e4 0x3f8 0x7a8 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x0e4 0x3f8 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x0e8 0x3fc 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT21__LCD_DATA21 0x0e8 0x3fc 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT21__ECSPI1_MOSI 0x0e8 0x3fc 0x7e0 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x0e8 0x3fc 0x79c 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x0e8 0x3fc 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x0ec 0x400 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT22__LCD_DATA22 0x0ec 0x400 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT22__ECSPI1_MISO 0x0ec 0x400 0x7dc 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x0ec 0x400 0x7ac 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16 0x0ec 0x400 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x0f0 0x404 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT23__LCD_DATA23 0x0f0 0x404 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT23__ECSPI1_SS0 0x0f0 0x404 0x7e4 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x0f0 0x404 0x798 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x0f0 0x404 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x0f4 0x408 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT3__LCD_DATA03 0x0f4 0x408 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT3__ECSPI3_SS0 0x0f4 0x408 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x0f4 0x408 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x0f8 0x40c 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT4__LCD_DATA04 0x0f8 0x40c 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT4__ECSPI3_SS1 0x0f8 0x40c 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x0f8 0x40c 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x0fc 0x410 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT5__LCD_DATA05 0x0fc 0x410 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT5__ECSPI3_SS2 0x0fc 0x410 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT5__AUD6_RXFS 0x0fc 0x410 0x000 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x0fc 0x410 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x100 0x414 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT6__LCD_DATA06 0x100 0x414 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT6__ECSPI3_SS3 0x100 0x414 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT6__AUD6_RXC 0x100 0x414 0x000 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x100 0x414 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x104 0x418 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT7__LCD_DATA07 0x104 0x418 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT7__ECSPI3_RDY 0x104 0x418 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x104 0x418 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x108 0x41c 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT8__LCD_DATA08 0x108 0x41c 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x108 0x41c 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x108 0x41c 0x000 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT8__GPIO4_IO29 0x108 0x41c 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10c 0x420 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT9__LCD_DATA09 0x10c 0x420 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x10c 0x420 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT9__WDOG2_B 0x10c 0x420 0x000 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x10c 0x420 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A16__EIM_ADDR16 0x110 0x4e0 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A16__IPU1_DI1_DISP_CLK 0x110 0x4e0 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A16__IPU1_CSI1_PIXCLK 0x110 0x4e0 0x8b8 0x2 0x0
+#define MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x110 0x4e0 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A16__SRC_BOOT_CFG16 0x110 0x4e0 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A16__EPDC_DATA00 0x110 0x4e0 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_A17__EIM_ADDR17 0x114 0x4e4 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A17__IPU1_DISP1_DATA12 0x114 0x4e4 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A17__IPU1_CSI1_DATA12 0x114 0x4e4 0x890 0x2 0x0
+#define MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x114 0x4e4 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A17__SRC_BOOT_CFG17 0x114 0x4e4 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A17__EPDC_PWR_STAT 0x114 0x4e4 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_A18__EIM_ADDR18 0x118 0x4e8 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A18__IPU1_DISP1_DATA13 0x118 0x4e8 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A18__IPU1_CSI1_DATA13 0x118 0x4e8 0x894 0x2 0x0
+#define MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x118 0x4e8 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A18__SRC_BOOT_CFG18 0x118 0x4e8 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A18__EPDC_PWR_CTRL0 0x118 0x4e8 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_A19__EIM_ADDR19 0x11c 0x4ec 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A19__IPU1_DISP1_DATA14 0x11c 0x4ec 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A19__IPU1_CSI1_DATA14 0x11c 0x4ec 0x898 0x2 0x0
+#define MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x11c 0x4ec 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A19__SRC_BOOT_CFG19 0x11c 0x4ec 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A19__EPDC_PWR_CTRL1 0x11c 0x4ec 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_A20__EIM_ADDR20 0x120 0x4f0 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A20__IPU1_DISP1_DATA15 0x120 0x4f0 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A20__IPU1_CSI1_DATA15 0x120 0x4f0 0x89c 0x2 0x0
+#define MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x120 0x4f0 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A20__SRC_BOOT_CFG20 0x120 0x4f0 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A20__EPDC_PWR_CTRL2 0x120 0x4f0 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_A21__EIM_ADDR21 0x124 0x4f4 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A21__IPU1_DISP1_DATA16 0x124 0x4f4 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A21__IPU1_CSI1_DATA16 0x124 0x4f4 0x8a0 0x2 0x0
+#define MX6QDL_PAD_EIM_A21__GPIO2_IO17 0x124 0x4f4 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A21__SRC_BOOT_CFG21 0x124 0x4f4 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A21__EPDC_GDCLK 0x124 0x4f4 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_A22__EIM_ADDR22 0x128 0x4f8 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A22__IPU1_DISP1_DATA17 0x128 0x4f8 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A22__IPU1_CSI1_DATA17 0x128 0x4f8 0x8a4 0x2 0x0
+#define MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x128 0x4f8 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A22__SRC_BOOT_CFG22 0x128 0x4f8 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A22__EPDC_GDSP 0x128 0x4f8 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_A23__EIM_ADDR23 0x12c 0x4fc 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A23__IPU1_DISP1_DATA18 0x12c 0x4fc 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A23__IPU1_CSI1_DATA18 0x12c 0x4fc 0x8a8 0x2 0x0
+#define MX6QDL_PAD_EIM_A23__IPU1_SISG3 0x12c 0x4fc 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x12c 0x4fc 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A23__SRC_BOOT_CFG23 0x12c 0x4fc 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A23__EPDC_GDOE 0x12c 0x4fc 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_A24__EIM_ADDR24 0x130 0x500 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A24__IPU1_DISP1_DATA19 0x130 0x500 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A24__IPU1_CSI1_DATA19 0x130 0x500 0x8ac 0x2 0x0
+#define MX6QDL_PAD_EIM_A24__IPU1_SISG2 0x130 0x500 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x130 0x500 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A24__SRC_BOOT_CFG24 0x130 0x500 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A24__EPDC_GDRL 0x130 0x500 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_A25__EIM_ADDR25 0x134 0x504 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A25__ECSPI4_SS1 0x134 0x504 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A25__ECSPI2_RDY 0x134 0x504 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_A25__IPU1_DI1_PIN12 0x134 0x504 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_A25__IPU1_DI0_D1_CS 0x134 0x504 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x134 0x504 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x134 0x504 0x85c 0x6 0x0
+#define MX6QDL_PAD_EIM_A25__EPDC_DATA15 0x134 0x504 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_A25__EIM_ACLK_FREERUN 0x134 0x504 0x000 0x9 0x0
+#define MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0x138 0x508 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_BCLK__IPU1_DI1_PIN16 0x138 0x508 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x138 0x508 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_BCLK__EPDC_SDCE9 0x138 0x508 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0x13c 0x50c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_CS0__IPU1_DI1_PIN05 0x13c 0x50c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x13c 0x50c 0x7f4 0x2 0x2
+#define MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x13c 0x50c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_CS0__EPDC_DATA06 0x13c 0x50c 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0x140 0x510 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_CS1__IPU1_DI1_PIN06 0x140 0x510 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x140 0x510 0x7fc 0x2 0x2
+#define MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x140 0x510 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_CS1__EPDC_DATA08 0x140 0x510 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D16__EIM_DATA16 0x144 0x514 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x144 0x514 0x7d8 0x1 0x2
+#define MX6QDL_PAD_EIM_D16__IPU1_DI0_PIN05 0x144 0x514 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D16__IPU1_CSI1_DATA18 0x144 0x514 0x8a8 0x3 0x1
+#define MX6QDL_PAD_EIM_D16__HDMI_TX_DDC_SDA 0x144 0x514 0x864 0x4 0x0
+#define MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x144 0x514 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D16__I2C2_SDA 0x144 0x514 0x874 0x6 0x0
+#define MX6QDL_PAD_EIM_D16__EPDC_DATA10 0x144 0x514 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D17__EIM_DATA17 0x148 0x518 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x148 0x518 0x7dc 0x1 0x2
+#define MX6QDL_PAD_EIM_D17__IPU1_DI0_PIN06 0x148 0x518 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D17__IPU1_CSI1_PIXCLK 0x148 0x518 0x8b8 0x3 0x1
+#define MX6QDL_PAD_EIM_D17__DCIC1_OUT 0x148 0x518 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D17__GPIO3_IO17 0x148 0x518 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D17__I2C3_SCL 0x148 0x518 0x878 0x6 0x0
+#define MX6QDL_PAD_EIM_D17__EPDC_VCOM0 0x148 0x518 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D18__EIM_DATA18 0x14c 0x51c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x14c 0x51c 0x7e0 0x1 0x2
+#define MX6QDL_PAD_EIM_D18__IPU1_DI0_PIN07 0x14c 0x51c 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D18__IPU1_CSI1_DATA17 0x14c 0x51c 0x8a4 0x3 0x1
+#define MX6QDL_PAD_EIM_D18__IPU1_DI1_D0_CS 0x14c 0x51c 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x14c 0x51c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D18__I2C3_SDA 0x14c 0x51c 0x87c 0x6 0x0
+#define MX6QDL_PAD_EIM_D18__EPDC_VCOM1 0x14c 0x51c 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D19__EIM_DATA19 0x150 0x520 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D19__ECSPI1_SS1 0x150 0x520 0x7e8 0x1 0x1
+#define MX6QDL_PAD_EIM_D19__IPU1_DI0_PIN08 0x150 0x520 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D19__IPU1_CSI1_DATA16 0x150 0x520 0x8a0 0x3 0x1
+#define MX6QDL_PAD_EIM_D19__UART1_CTS_B 0x150 0x520 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D19__UART1_RTS_B 0x150 0x520 0x8f8 0x4 0x0
+#define MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x150 0x520 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D19__EPIT1_OUT 0x150 0x520 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D19__EPDC_DATA12 0x150 0x520 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D20__EIM_DATA20 0x154 0x524 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D20__ECSPI4_SS0 0x154 0x524 0x808 0x1 0x0
+#define MX6QDL_PAD_EIM_D20__IPU1_DI0_PIN16 0x154 0x524 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D20__IPU1_CSI1_DATA15 0x154 0x524 0x89c 0x3 0x1
+#define MX6QDL_PAD_EIM_D20__UART1_RTS_B 0x154 0x524 0x8f8 0x4 0x1
+#define MX6QDL_PAD_EIM_D20__UART1_CTS_B 0x154 0x524 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x154 0x524 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D20__EPIT2_OUT 0x154 0x524 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D21__EIM_DATA21 0x158 0x528 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x158 0x528 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D21__IPU1_DI0_PIN17 0x158 0x528 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D21__IPU1_CSI1_DATA11 0x158 0x528 0x88c 0x3 0x0
+#define MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x158 0x528 0x920 0x4 0x0
+#define MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x158 0x528 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D21__I2C1_SCL 0x158 0x528 0x868 0x6 0x1
+#define MX6QDL_PAD_EIM_D21__SPDIF_IN 0x158 0x528 0x8f0 0x7 0x0
+#define MX6QDL_PAD_EIM_D22__EIM_DATA22 0x15c 0x52c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x15c 0x52c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D22__IPU1_DI0_PIN01 0x15c 0x52c 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D22__IPU1_CSI1_DATA10 0x15c 0x52c 0x888 0x3 0x0
+#define MX6QDL_PAD_EIM_D22__USB_OTG_PWR 0x15c 0x52c 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x15c 0x52c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D22__SPDIF_OUT 0x15c 0x52c 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D22__EPDC_SDCE6 0x15c 0x52c 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D23__EIM_DATA23 0x160 0x530 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D23__IPU1_DI0_D0_CS 0x160 0x530 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x160 0x530 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D23__UART3_RTS_B 0x160 0x530 0x908 0x2 0x0
+#define MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x160 0x530 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_D23__IPU1_CSI1_DATA_EN 0x160 0x530 0x8b0 0x4 0x0
+#define MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x160 0x530 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D23__IPU1_DI1_PIN02 0x160 0x530 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D23__IPU1_DI1_PIN14 0x160 0x530 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D23__EPDC_DATA11 0x160 0x530 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D24__EIM_DATA24 0x164 0x534 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D24__ECSPI4_SS2 0x164 0x534 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x164 0x534 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D24__UART3_RX_DATA 0x164 0x534 0x90c 0x2 0x0
+#define MX6QDL_PAD_EIM_D24__ECSPI1_SS2 0x164 0x534 0x7ec 0x3 0x0
+#define MX6QDL_PAD_EIM_D24__ECSPI2_SS2 0x164 0x534 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x164 0x534 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D24__AUD5_RXFS 0x164 0x534 0x7bc 0x6 0x1
+#define MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x164 0x534 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D24__EPDC_SDCE7 0x164 0x534 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D25__EIM_DATA25 0x168 0x538 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D25__ECSPI4_SS3 0x168 0x538 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x168 0x538 0x90c 0x2 0x1
+#define MX6QDL_PAD_EIM_D25__UART3_TX_DATA 0x168 0x538 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D25__ECSPI1_SS3 0x168 0x538 0x7f0 0x3 0x0
+#define MX6QDL_PAD_EIM_D25__ECSPI2_SS3 0x168 0x538 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x168 0x538 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D25__AUD5_RXC 0x168 0x538 0x7b8 0x6 0x1
+#define MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x168 0x538 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D25__EPDC_SDCE8 0x168 0x538 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D26__EIM_DATA26 0x16c 0x53c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D26__IPU1_DI1_PIN11 0x16c 0x53c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D26__IPU1_CSI0_DATA01 0x16c 0x53c 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D26__IPU1_CSI1_DATA14 0x16c 0x53c 0x898 0x3 0x1
+#define MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x16c 0x53c 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x16c 0x53c 0x904 0x4 0x0
+#define MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x16c 0x53c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D26__IPU1_SISG2 0x16c 0x53c 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D26__IPU1_DISP1_DATA22 0x16c 0x53c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D26__EPDC_SDOED 0x16c 0x53c 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D27__EIM_DATA27 0x170 0x540 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D27__IPU1_DI1_PIN13 0x170 0x540 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D27__IPU1_CSI0_DATA00 0x170 0x540 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D27__IPU1_CSI1_DATA13 0x170 0x540 0x894 0x3 0x1
+#define MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x170 0x540 0x904 0x4 0x1
+#define MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x170 0x540 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x170 0x540 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D27__IPU1_SISG3 0x170 0x540 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D27__IPU1_DISP1_DATA23 0x170 0x540 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D27__EPDC_SDOE 0x170 0x540 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D28__EIM_DATA28 0x174 0x544 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D28__I2C1_SDA 0x174 0x544 0x86c 0x1 0x1
+#define MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x174 0x544 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D28__IPU1_CSI1_DATA12 0x174 0x544 0x890 0x3 0x1
+#define MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x174 0x544 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D28__UART2_RTS_B 0x174 0x544 0x900 0x4 0x0
+#define MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x174 0x544 0x900 0x4 0x0
+#define MX6QDL_PAD_EIM_D28__UART2_DTE_RTS_B 0x174 0x544 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x174 0x544 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D28__IPU1_EXT_TRIG 0x174 0x544 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D28__IPU1_DI0_PIN13 0x174 0x544 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D28__EPDC_PWR_CTRL3 0x174 0x544 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D29__EIM_DATA29 0x178 0x548 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D29__IPU1_DI1_PIN15 0x178 0x548 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D29__ECSPI4_SS0 0x178 0x548 0x808 0x2 0x1
+#define MX6QDL_PAD_EIM_D29__UART2_RTS_B 0x178 0x548 0x900 0x4 0x1
+#define MX6QDL_PAD_EIM_D29__UART2_CTS_B 0x178 0x548 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x178 0x548 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D29__UART2_DTE_CTS_B 0x178 0x548 0x900 0x4 0x1
+#define MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x178 0x548 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D29__IPU1_CSI1_VSYNC 0x178 0x548 0x8bc 0x6 0x0
+#define MX6QDL_PAD_EIM_D29__IPU1_DI0_PIN14 0x178 0x548 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D29__EPDC_PWR_WAKE 0x178 0x548 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D30__EIM_DATA30 0x17c 0x54c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D30__IPU1_DISP1_DATA21 0x17c 0x54c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D30__IPU1_DI0_PIN11 0x17c 0x54c 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D30__IPU1_CSI0_DATA03 0x17c 0x54c 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_D30__UART3_CTS_B 0x17c 0x54c 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D30__UART3_RTS_B 0x17c 0x54c 0x908 0x4 0x1
+#define MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x17c 0x54c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D30__USB_H1_OC 0x17c 0x54c 0x924 0x6 0x0
+#define MX6QDL_PAD_EIM_D30__EPDC_SDOEZ 0x17c 0x54c 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D31__EIM_DATA31 0x180 0x550 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D31__IPU1_DISP1_DATA20 0x180 0x550 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D31__IPU1_DI0_PIN12 0x180 0x550 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D31__IPU1_CSI0_DATA02 0x180 0x550 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x180 0x550 0x908 0x4 0x2
+#define MX6QDL_PAD_EIM_D31__UART3_CTS_B 0x180 0x550 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x180 0x550 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D31__USB_H1_PWR 0x180 0x550 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D31__EPDC_SDCLK_P 0x180 0x550 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_D31__EIM_ACLK_FREERUN 0x180 0x550 0x000 0x9 0x0
+#define MX6QDL_PAD_EIM_DA0__EIM_AD00 0x184 0x554 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA0__IPU1_DISP1_DATA09 0x184 0x554 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA0__IPU1_CSI1_DATA09 0x184 0x554 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x184 0x554 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA0__SRC_BOOT_CFG00 0x184 0x554 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA0__EPDC_SDCLK_N 0x184 0x554 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA1__EIM_AD01 0x188 0x558 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA1__IPU1_DISP1_DATA08 0x188 0x558 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA1__IPU1_CSI1_DATA08 0x188 0x558 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x188 0x558 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA1__SRC_BOOT_CFG01 0x188 0x558 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA1__EPDC_SDLE 0x188 0x558 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA10__EIM_AD10 0x18c 0x55c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA10__IPU1_DI1_PIN15 0x18c 0x55c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA10__IPU1_CSI1_DATA_EN 0x18c 0x55c 0x8b0 0x2 0x1
+#define MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x18c 0x55c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA10__SRC_BOOT_CFG10 0x18c 0x55c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA10__EPDC_DATA01 0x18c 0x55c 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA11__EIM_AD11 0x190 0x560 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA11__IPU1_DI1_PIN02 0x190 0x560 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA11__IPU1_CSI1_HSYNC 0x190 0x560 0x8b4 0x2 0x0
+#define MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x190 0x560 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA11__SRC_BOOT_CFG11 0x190 0x560 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA11__EPDC_DATA03 0x190 0x560 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA12__EIM_AD12 0x194 0x564 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA12__IPU1_DI1_PIN03 0x194 0x564 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA12__IPU1_CSI1_VSYNC 0x194 0x564 0x8bc 0x2 0x1
+#define MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x194 0x564 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA12__SRC_BOOT_CFG12 0x194 0x564 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA12__EPDC_DATA02 0x194 0x564 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA13__EIM_AD13 0x198 0x568 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA13__IPU1_DI1_D0_CS 0x198 0x568 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x198 0x568 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA13__SRC_BOOT_CFG13 0x198 0x568 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA13__EPDC_DATA13 0x198 0x568 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA14__EIM_AD14 0x19c 0x56c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA14__IPU1_DI1_D1_CS 0x19c 0x56c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x19c 0x56c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA14__SRC_BOOT_CFG14 0x19c 0x56c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA14__EPDC_DATA14 0x19c 0x56c 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA15__EIM_AD15 0x1a0 0x570 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA15__IPU1_DI1_PIN01 0x1a0 0x570 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA15__IPU1_DI1_PIN04 0x1a0 0x570 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x1a0 0x570 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA15__SRC_BOOT_CFG15 0x1a0 0x570 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA15__EPDC_DATA09 0x1a0 0x570 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA2__EIM_AD02 0x1a4 0x574 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA2__IPU1_DISP1_DATA07 0x1a4 0x574 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA2__IPU1_CSI1_DATA07 0x1a4 0x574 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x1a4 0x574 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA2__SRC_BOOT_CFG02 0x1a4 0x574 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA2__EPDC_BDR0 0x1a4 0x574 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA3__EIM_AD03 0x1a8 0x578 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA3__IPU1_DISP1_DATA06 0x1a8 0x578 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA3__IPU1_CSI1_DATA06 0x1a8 0x578 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x1a8 0x578 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA3__SRC_BOOT_CFG03 0x1a8 0x578 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA3__EPDC_BDR1 0x1a8 0x578 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA4__EIM_AD04 0x1ac 0x57c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA4__IPU1_DISP1_DATA05 0x1ac 0x57c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA4__IPU1_CSI1_DATA05 0x1ac 0x57c 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x1ac 0x57c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA4__SRC_BOOT_CFG04 0x1ac 0x57c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA4__EPDC_SDCE0 0x1ac 0x57c 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA5__EIM_AD05 0x1b0 0x580 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA5__IPU1_DISP1_DATA04 0x1b0 0x580 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA5__IPU1_CSI1_DATA04 0x1b0 0x580 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x1b0 0x580 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA5__SRC_BOOT_CFG05 0x1b0 0x580 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA5__EPDC_SDCE1 0x1b0 0x580 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA6__EIM_AD06 0x1b4 0x584 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA6__IPU1_DISP1_DATA03 0x1b4 0x584 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA6__IPU1_CSI1_DATA03 0x1b4 0x584 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x1b4 0x584 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA6__SRC_BOOT_CFG06 0x1b4 0x584 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA6__EPDC_SDCE2 0x1b4 0x584 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA7__EIM_AD07 0x1b8 0x588 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA7__IPU1_DISP1_DATA02 0x1b8 0x588 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA7__IPU1_CSI1_DATA02 0x1b8 0x588 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x1b8 0x588 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA7__SRC_BOOT_CFG07 0x1b8 0x588 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA7__EPDC_SDCE3 0x1b8 0x588 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA8__EIM_AD08 0x1bc 0x58c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA8__IPU1_DISP1_DATA01 0x1bc 0x58c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA8__IPU1_CSI1_DATA01 0x1bc 0x58c 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x1bc 0x58c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA8__SRC_BOOT_CFG08 0x1bc 0x58c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA8__EPDC_SDCE4 0x1bc 0x58c 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_DA9__EIM_AD09 0x1c0 0x590 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA9__IPU1_DISP1_DATA00 0x1c0 0x590 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA9__IPU1_CSI1_DATA00 0x1c0 0x590 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x1c0 0x590 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA9__SRC_BOOT_CFG09 0x1c0 0x590 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA9__EPDC_SDCE5 0x1c0 0x590 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0x1c4 0x594 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_EB0__IPU1_DISP1_DATA11 0x1c4 0x594 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_EB0__IPU1_CSI1_DATA11 0x1c4 0x594 0x88c 0x2 0x1
+#define MX6QDL_PAD_EIM_EB0__CCM_PMIC_READY 0x1c4 0x594 0x7d4 0x4 0x0
+#define MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1c4 0x594 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_EB0__SRC_BOOT_CFG27 0x1c4 0x594 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_EB0__EPDC_PWR_COM 0x1c4 0x594 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0x1c8 0x598 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_EB1__IPU1_DISP1_DATA10 0x1c8 0x598 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_EB1__IPU1_CSI1_DATA10 0x1c8 0x598 0x888 0x2 0x1
+#define MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1c8 0x598 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_EB1__SRC_BOOT_CFG28 0x1c8 0x598 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_EB1__EPDC_SDSHR 0x1c8 0x598 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0x1cc 0x59c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_EB2__ECSPI1_SS0 0x1cc 0x59c 0x7e4 0x1 0x2
+#define MX6QDL_PAD_EIM_EB2__IPU1_CSI1_DATA19 0x1cc 0x59c 0x8ac 0x3 0x1
+#define MX6QDL_PAD_EIM_EB2__HDMI_TX_DDC_SCL 0x1cc 0x59c 0x860 0x4 0x0
+#define MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1cc 0x59c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x1cc 0x59c 0x870 0x6 0x0
+#define MX6QDL_PAD_EIM_EB2__SRC_BOOT_CFG30 0x1cc 0x59c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_EB2__EPDC_DATA05 0x1cc 0x59c 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0x1d0 0x5a0 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_EB3__ECSPI4_RDY 0x1d0 0x5a0 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1d0 0x5a0 0x908 0x2 0x3
+#define MX6QDL_PAD_EIM_EB3__UART3_CTS_B 0x1d0 0x5a0 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_EB3__UART1_RI_B 0x1d0 0x5a0 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_EB3__IPU1_CSI1_HSYNC 0x1d0 0x5a0 0x8b4 0x4 0x1
+#define MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x1d0 0x5a0 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_EB3__IPU1_DI1_PIN03 0x1d0 0x5a0 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_EB3__SRC_BOOT_CFG31 0x1d0 0x5a0 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_EB3__EPDC_SDCE0 0x1d0 0x5a0 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_EB3__EIM_ACLK_FREERUN 0x1d0 0x5a0 0x000 0x9 0x0
+#define MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0x1d4 0x5a4 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_LBA__IPU1_DI1_PIN17 0x1d4 0x5a4 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_LBA__ECSPI2_SS1 0x1d4 0x5a4 0x804 0x2 0x1
+#define MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x1d4 0x5a4 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_LBA__SRC_BOOT_CFG26 0x1d4 0x5a4 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_LBA__EPDC_DATA04 0x1d4 0x5a4 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_OE__EIM_OE_B 0x1d8 0x5a8 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_OE__IPU1_DI1_PIN07 0x1d8 0x5a8 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x1d8 0x5a8 0x7f8 0x2 0x2
+#define MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x1d8 0x5a8 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_OE__EPDC_PWR_IRQ 0x1d8 0x5a8 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_RW__EIM_RW 0x1dc 0x5ac 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_RW__IPU1_DI1_PIN08 0x1dc 0x5ac 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_RW__ECSPI2_SS0 0x1dc 0x5ac 0x800 0x2 0x2
+#define MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x1dc 0x5ac 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_RW__SRC_BOOT_CFG29 0x1dc 0x5ac 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_RW__EPDC_DATA07 0x1dc 0x5ac 0x000 0x8 0x0
+#define MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0x1e0 0x5b0 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_WAIT__EIM_DTACK_B 0x1e0 0x5b0 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x1e0 0x5b0 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_WAIT__SRC_BOOT_CFG25 0x1e0 0x5b0 0x000 0x7 0x0
+#define MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1e4 0x5b4 0x828 0x1 0x0
+#define MX6QDL_PAD_ENET_CRS_DV__ESAI_TX_CLK 0x1e4 0x5b4 0x840 0x2 0x0
+#define MX6QDL_PAD_ENET_CRS_DV__SPDIF_EXT_CLK 0x1e4 0x5b4 0x8f4 0x3 0x0
+#define MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1e4 0x5b4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_MDC__MLB_DATA 0x1e8 0x5b8 0x8e0 0x0 0x0
+#define MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1e8 0x5b8 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_MDC__ESAI_TX5_RX0 0x1e8 0x5b8 0x858 0x2 0x0
+#define MX6QDL_PAD_ENET_MDC__ENET_1588_EVENT1_IN 0x1e8 0x5b8 0x000 0x4 0x0
+#define MX6QDL_PAD_ENET_MDC__GPIO1_IO31 0x1e8 0x5b8 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1ec 0x5bc 0x810 0x1 0x0
+#define MX6QDL_PAD_ENET_MDIO__ESAI_RX_CLK 0x1ec 0x5bc 0x83c 0x2 0x0
+#define MX6QDL_PAD_ENET_MDIO__ENET_1588_EVENT1_OUT 0x1ec 0x5bc 0x000 0x4 0x0
+#define MX6QDL_PAD_ENET_MDIO__GPIO1_IO22 0x1ec 0x5bc 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_MDIO__SPDIF_LOCK 0x1ec 0x5bc 0x000 0x6 0x0
+#define MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1f0 0x5c0 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_REF_CLK__ESAI_RX_FS 0x1f0 0x5c0 0x82c 0x2 0x0
+#define MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1f0 0x5c0 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_REF_CLK__SPDIF_SR_CLK 0x1f0 0x5c0 0x000 0x6 0x0
+#define MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f4 0x5c4 0x790 0x0 0x0
+#define MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1f4 0x5c4 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_RX_ER__ESAI_RX_HF_CLK 0x1f4 0x5c4 0x834 0x2 0x0
+#define MX6QDL_PAD_ENET_RX_ER__SPDIF_IN 0x1f4 0x5c4 0x8f0 0x3 0x1
+#define MX6QDL_PAD_ENET_RX_ER__ENET_1588_EVENT2_OUT 0x1f4 0x5c4 0x000 0x4 0x0
+#define MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x1f4 0x5c4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1f8 0x5c8 0x818 0x1 0x0
+#define MX6QDL_PAD_ENET_RXD0__ESAI_TX_HF_CLK 0x1f8 0x5c8 0x838 0x2 0x0
+#define MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1f8 0x5c8 0x000 0x3 0x0
+#define MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1f8 0x5c8 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_RXD1__MLB_SIG 0x1fc 0x5cc 0x8e4 0x0 0x0
+#define MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1fc 0x5cc 0x81c 0x1 0x0
+#define MX6QDL_PAD_ENET_RXD1__ESAI_TX_FS 0x1fc 0x5cc 0x830 0x2 0x0
+#define MX6QDL_PAD_ENET_RXD1__ENET_1588_EVENT3_OUT 0x1fc 0x5cc 0x000 0x4 0x0
+#define MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1fc 0x5cc 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x200 0x5d0 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_TX_EN__ESAI_TX3_RX2 0x200 0x5d0 0x850 0x2 0x0
+#define MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x200 0x5d0 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_TX_EN__I2C4_SCL 0x200 0x5d0 0x880 0x9 0x0
+#define MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x204 0x5d4 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_TXD0__ESAI_TX4_RX1 0x204 0x5d4 0x854 0x2 0x0
+#define MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x204 0x5d4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_TXD1__MLB_CLK 0x208 0x5d8 0x8dc 0x0 0x0
+#define MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x208 0x5d8 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_TXD1__ESAI_TX2_RX3 0x208 0x5d8 0x84c 0x2 0x0
+#define MX6QDL_PAD_ENET_TXD1__ENET_1588_EVENT0_IN 0x208 0x5d8 0x000 0x4 0x0
+#define MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x208 0x5d8 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_TXD1__I2C4_SDA 0x208 0x5d8 0x884 0x9 0x0
+#define MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x20c 0x5dc 0x000 0x0 0x0
+#define MX6QDL_PAD_GPIO_0__KEY_COL5 0x20c 0x5dc 0x8c0 0x2 0x1
+#define MX6QDL_PAD_GPIO_0__ASRC_EXT_CLK 0x20c 0x5dc 0x794 0x3 0x0
+#define MX6QDL_PAD_GPIO_0__EPIT1_OUT 0x20c 0x5dc 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x20c 0x5dc 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_0__USB_H1_PWR 0x20c 0x5dc 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_0__SNVS_VIO_5 0x20c 0x5dc 0x000 0x7 0x0
+#define MX6QDL_PAD_GPIO_1__ESAI_RX_CLK 0x210 0x5e0 0x83c 0x0 0x1
+#define MX6QDL_PAD_GPIO_1__WDOG2_B 0x210 0x5e0 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_1__KEY_ROW5 0x210 0x5e0 0x8cc 0x2 0x1
+#define MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x210 0x5e0 0x790 0x3 0x1
+#define MX6QDL_PAD_GPIO_1__PWM2_OUT 0x210 0x5e0 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x210 0x5e0 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_1__SD1_CD_B 0x210 0x5e0 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_16__ESAI_TX3_RX2 0x214 0x5e4 0x850 0x0 0x1
+#define MX6QDL_PAD_GPIO_16__ENET_1588_EVENT2_IN 0x214 0x5e4 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x214 0x5e4 0x80c 0x2 0x0
+#define MX6QDL_PAD_GPIO_16__SD1_LCTL 0x214 0x5e4 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_16__SPDIF_IN 0x214 0x5e4 0x8f0 0x4 0x2
+#define MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x214 0x5e4 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_16__I2C3_SDA 0x214 0x5e4 0x87c 0x6 0x1
+#define MX6QDL_PAD_GPIO_16__JTAG_DE_B 0x214 0x5e4 0x000 0x7 0x0
+#define MX6QDL_PAD_GPIO_17__ESAI_TX0 0x218 0x5e8 0x844 0x0 0x0
+#define MX6QDL_PAD_GPIO_17__ENET_1588_EVENT3_IN 0x218 0x5e8 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_17__CCM_PMIC_READY 0x218 0x5e8 0x7d4 0x2 0x1
+#define MX6QDL_PAD_GPIO_17__SDMA_EXT_EVENT0 0x218 0x5e8 0x8e8 0x3 0x1
+#define MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x218 0x5e8 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x218 0x5e8 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_18__ESAI_TX1 0x21c 0x5ec 0x848 0x0 0x0
+#define MX6QDL_PAD_GPIO_18__ENET_RX_CLK 0x21c 0x5ec 0x814 0x1 0x0
+#define MX6QDL_PAD_GPIO_18__SD3_VSELECT 0x21c 0x5ec 0x000 0x2 0x0
+#define MX6QDL_PAD_GPIO_18__SDMA_EXT_EVENT1 0x21c 0x5ec 0x8ec 0x3 0x1
+#define MX6QDL_PAD_GPIO_18__ASRC_EXT_CLK 0x21c 0x5ec 0x794 0x4 0x1
+#define MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x21c 0x5ec 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_18__SNVS_VIO_5_CTL 0x21c 0x5ec 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_19__KEY_COL5 0x220 0x5f0 0x8c0 0x0 0x2
+#define MX6QDL_PAD_GPIO_19__ENET_1588_EVENT0_OUT 0x220 0x5f0 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x220 0x5f0 0x000 0x2 0x0
+#define MX6QDL_PAD_GPIO_19__CCM_CLKO1 0x220 0x5f0 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_19__ECSPI1_RDY 0x220 0x5f0 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x220 0x5f0 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_19__ENET_TX_ER 0x220 0x5f0 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_2__ESAI_TX_FS 0x224 0x5f4 0x830 0x0 0x1
+#define MX6QDL_PAD_GPIO_2__KEY_ROW6 0x224 0x5f4 0x8d0 0x2 0x1
+#define MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x224 0x5f4 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_2__SD2_WP 0x224 0x5f4 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_2__MLB_DATA 0x224 0x5f4 0x8e0 0x7 0x1
+#define MX6QDL_PAD_GPIO_3__ESAI_RX_HF_CLK 0x228 0x5f8 0x834 0x0 0x1
+#define MX6QDL_PAD_GPIO_3__I2C3_SCL 0x228 0x5f8 0x878 0x2 0x1
+#define MX6QDL_PAD_GPIO_3__XTALOSC_REF_CLK_24M 0x228 0x5f8 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_3__CCM_CLKO2 0x228 0x5f8 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x228 0x5f8 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_3__USB_H1_OC 0x228 0x5f8 0x924 0x6 0x1
+#define MX6QDL_PAD_GPIO_3__MLB_CLK 0x228 0x5f8 0x8dc 0x7 0x1
+#define MX6QDL_PAD_GPIO_4__ESAI_TX_HF_CLK 0x22c 0x5fc 0x838 0x0 0x1
+#define MX6QDL_PAD_GPIO_4__KEY_COL7 0x22c 0x5fc 0x8c8 0x2 0x1
+#define MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x22c 0x5fc 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_4__SD2_CD_B 0x22c 0x5fc 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_5__ESAI_TX2_RX3 0x230 0x600 0x84c 0x0 0x1
+#define MX6QDL_PAD_GPIO_5__KEY_ROW7 0x230 0x600 0x8d4 0x2 0x1
+#define MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x230 0x600 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x230 0x600 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_5__I2C3_SCL 0x230 0x600 0x878 0x6 0x2
+#define MX6QDL_PAD_GPIO_5__ARM_EVENTI 0x230 0x600 0x000 0x7 0x0
+#define MX6QDL_PAD_GPIO_6__ESAI_TX_CLK 0x234 0x604 0x840 0x0 0x1
+#define MX6QDL_PAD_GPIO_6__ENET_IRQ 0x234 0x604 0x03c 0x11 0xff000609
+#define MX6QDL_PAD_GPIO_6__I2C3_SDA 0x234 0x604 0x87c 0x2 0x2
+#define MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x234 0x604 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_6__SD2_LCTL 0x234 0x604 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_6__MLB_SIG 0x234 0x604 0x8e4 0x7 0x1
+#define MX6QDL_PAD_GPIO_7__ESAI_TX4_RX1 0x238 0x608 0x854 0x0 0x1
+#define MX6QDL_PAD_GPIO_7__EPIT1_OUT 0x238 0x608 0x000 0x2 0x0
+#define MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x238 0x608 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_7__UART2_TX_DATA 0x238 0x608 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_7__UART2_RX_DATA 0x238 0x608 0x904 0x4 0x2
+#define MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x238 0x608 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_7__SPDIF_LOCK 0x238 0x608 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_7__USB_OTG_HOST_MODE 0x238 0x608 0x000 0x7 0x0
+#define MX6QDL_PAD_GPIO_7__I2C4_SCL 0x238 0x608 0x880 0x8 0x1
+#define MX6QDL_PAD_GPIO_8__ESAI_TX5_RX0 0x23c 0x60c 0x858 0x0 0x1
+#define MX6QDL_PAD_GPIO_8__XTALOSC_REF_CLK_32K 0x23c 0x60c 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_8__EPIT2_OUT 0x23c 0x60c 0x000 0x2 0x0
+#define MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x23c 0x60c 0x7c8 0x3 0x0
+#define MX6QDL_PAD_GPIO_8__UART2_RX_DATA 0x23c 0x60c 0x904 0x4 0x3
+#define MX6QDL_PAD_GPIO_8__UART2_TX_DATA 0x23c 0x60c 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x23c 0x60c 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_8__SPDIF_SR_CLK 0x23c 0x60c 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_8__USB_OTG_PWR_CTL_WAKE 0x23c 0x60c 0x000 0x7 0x0
+#define MX6QDL_PAD_GPIO_8__I2C4_SDA 0x23c 0x60c 0x884 0x8 0x1
+#define MX6QDL_PAD_GPIO_9__ESAI_RX_FS 0x240 0x610 0x82c 0x0 0x1
+#define MX6QDL_PAD_GPIO_9__WDOG1_B 0x240 0x610 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_9__KEY_COL6 0x240 0x610 0x8c4 0x2 0x1
+#define MX6QDL_PAD_GPIO_9__CCM_REF_EN_B 0x240 0x610 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_9__PWM1_OUT 0x240 0x610 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x240 0x610 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_9__SD1_WP 0x240 0x610 0x92c 0x6 0x1
+#define MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x244 0x62c 0x7d8 0x0 0x3
+#define MX6QDL_PAD_KEY_COL0__ENET_RX_DATA3 0x244 0x62c 0x824 0x1 0x0
+#define MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x244 0x62c 0x7c0 0x2 0x1
+#define MX6QDL_PAD_KEY_COL0__KEY_COL0 0x244 0x62c 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x244 0x62c 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_COL0__UART4_RX_DATA 0x244 0x62c 0x914 0x4 0x2
+#define MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x244 0x62c 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_COL0__DCIC1_OUT 0x244 0x62c 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x248 0x630 0x7dc 0x0 0x3
+#define MX6QDL_PAD_KEY_COL1__ENET_MDIO 0x248 0x630 0x810 0x1 0x1
+#define MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x248 0x630 0x7c4 0x2 0x1
+#define MX6QDL_PAD_KEY_COL1__KEY_COL1 0x248 0x630 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x248 0x630 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_COL1__UART5_RX_DATA 0x248 0x630 0x91c 0x4 0x2
+#define MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x248 0x630 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_COL1__SD1_VSELECT 0x248 0x630 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_COL2__ECSPI1_SS1 0x24c 0x634 0x7e8 0x0 0x2
+#define MX6QDL_PAD_KEY_COL2__ENET_RX_DATA2 0x24c 0x634 0x820 0x1 0x0
+#define MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x24c 0x634 0x000 0x2 0x0
+#define MX6QDL_PAD_KEY_COL2__KEY_COL2 0x24c 0x634 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_COL2__ENET_MDC 0x24c 0x634 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x24c 0x634 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_COL2__USB_H1_PWR_CTL_WAKE 0x24c 0x634 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_COL3__ECSPI1_SS3 0x250 0x638 0x7f0 0x0 0x1
+#define MX6QDL_PAD_KEY_COL3__ENET_CRS 0x250 0x638 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_COL3__HDMI_TX_DDC_SCL 0x250 0x638 0x860 0x2 0x1
+#define MX6QDL_PAD_KEY_COL3__KEY_COL3 0x250 0x638 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x250 0x638 0x870 0x4 0x1
+#define MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x250 0x638 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_COL3__SPDIF_IN 0x250 0x638 0x8f0 0x6 0x3
+#define MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x254 0x63c 0x000 0x0 0x0
+#define MX6QDL_PAD_KEY_COL4__IPU1_SISG4 0x254 0x63c 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x254 0x63c 0x920 0x2 0x1
+#define MX6QDL_PAD_KEY_COL4__KEY_COL4 0x254 0x63c 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_COL4__UART5_RTS_B 0x254 0x63c 0x918 0x4 0x2
+#define MX6QDL_PAD_KEY_COL4__UART5_CTS_B 0x254 0x63c 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x254 0x63c 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x258 0x640 0x7e0 0x0 0x3
+#define MX6QDL_PAD_KEY_ROW0__ENET_TX_DATA3 0x258 0x640 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x258 0x640 0x7b4 0x2 0x1
+#define MX6QDL_PAD_KEY_ROW0__KEY_ROW0 0x258 0x640 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x258 0x640 0x914 0x4 0x3
+#define MX6QDL_PAD_KEY_ROW0__UART4_TX_DATA 0x258 0x640 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x258 0x640 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_ROW0__DCIC2_OUT 0x258 0x640 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_ROW1__ECSPI1_SS0 0x25c 0x644 0x7e4 0x0 0x3
+#define MX6QDL_PAD_KEY_ROW1__ENET_COL 0x25c 0x644 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_ROW1__AUD5_RXD 0x25c 0x644 0x7b0 0x2 0x1
+#define MX6QDL_PAD_KEY_ROW1__KEY_ROW1 0x25c 0x644 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x25c 0x644 0x91c 0x4 0x3
+#define MX6QDL_PAD_KEY_ROW1__UART5_TX_DATA 0x25c 0x644 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x25c 0x644 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_ROW1__SD2_VSELECT 0x25c 0x644 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_ROW2__ECSPI1_SS2 0x260 0x648 0x7ec 0x0 0x1
+#define MX6QDL_PAD_KEY_ROW2__ENET_TX_DATA2 0x260 0x648 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x260 0x648 0x7c8 0x2 0x1
+#define MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x260 0x648 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_ROW2__SD2_VSELECT 0x260 0x648 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x260 0x648 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x260 0x648 0x85c 0x6 0x1
+#define MX6QDL_PAD_KEY_ROW3__ASRC_EXT_CLK 0x264 0x64c 0x794 0x1 0x2
+#define MX6QDL_PAD_KEY_ROW3__HDMI_TX_DDC_SDA 0x264 0x64c 0x864 0x2 0x1
+#define MX6QDL_PAD_KEY_ROW3__KEY_ROW3 0x264 0x64c 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x264 0x64c 0x874 0x4 0x1
+#define MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x264 0x64c 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_ROW3__SD1_VSELECT 0x264 0x64c 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x268 0x650 0x7cc 0x0 0x0
+#define MX6QDL_PAD_KEY_ROW4__IPU1_SISG5 0x268 0x650 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_ROW4__USB_OTG_PWR 0x268 0x650 0x000 0x2 0x0
+#define MX6QDL_PAD_KEY_ROW4__KEY_ROW4 0x268 0x650 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_ROW4__UART5_CTS_B 0x268 0x650 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_ROW4__UART5_RTS_B 0x268 0x650 0x918 0x4 0x3
+#define MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x268 0x650 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_ALE__NAND_ALE 0x26c 0x654 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x26c 0x654 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x26c 0x654 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CLE__NAND_CLE 0x270 0x658 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x270 0x658 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0x274 0x65c 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x274 0x65c 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0x278 0x660 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_CS1__SD4_VSELECT 0x278 0x660 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x278 0x660 0x000 0x2 0x0
+#define MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x278 0x660 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CS2__NAND_CE2_B 0x27c 0x664 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_CS2__IPU1_SISG0 0x27c 0x664 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_CS2__ESAI_TX0 0x27c 0x664 0x844 0x2 0x1
+#define MX6QDL_PAD_NANDF_CS2__EIM_CRE 0x27c 0x664 0x000 0x3 0x0
+#define MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x27c 0x664 0x000 0x4 0x0
+#define MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x27c 0x664 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CS3__NAND_CE3_B 0x280 0x668 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_CS3__IPU1_SISG1 0x280 0x668 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_CS3__ESAI_TX1 0x280 0x668 0x848 0x2 0x1
+#define MX6QDL_PAD_NANDF_CS3__EIM_ADDR26 0x280 0x668 0x000 0x3 0x0
+#define MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x280 0x668 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CS3__I2C4_SDA 0x280 0x668 0x884 0x9 0x2
+#define MX6QDL_PAD_NANDF_D0__NAND_DATA00 0x284 0x66c 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D0__SD1_DATA4 0x284 0x66c 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x284 0x66c 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D1__NAND_DATA01 0x288 0x670 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D1__SD1_DATA5 0x288 0x670 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x288 0x670 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D2__NAND_DATA02 0x28c 0x674 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D2__SD1_DATA6 0x28c 0x674 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x28c 0x674 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D3__NAND_DATA03 0x290 0x678 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D3__SD1_DATA7 0x290 0x678 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x290 0x678 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D4__NAND_DATA04 0x294 0x67c 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D4__SD2_DATA4 0x294 0x67c 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x294 0x67c 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D5__NAND_DATA05 0x298 0x680 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D5__SD2_DATA5 0x298 0x680 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x298 0x680 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D6__NAND_DATA06 0x29c 0x684 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D6__SD2_DATA6 0x29c 0x684 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x29c 0x684 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D7__NAND_DATA07 0x2a0 0x688 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D7__SD2_DATA7 0x2a0 0x688 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x2a0 0x688 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0x2a4 0x68c 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x2a4 0x68c 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0x2a8 0x690 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x2a8 0x690 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_WP_B__I2C4_SCL 0x2a8 0x690 0x880 0x9 0x2
+#define MX6QDL_PAD_RGMII_RD0__HSI_RX_READY 0x2ac 0x694 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x2ac 0x694 0x818 0x1 0x1
+#define MX6QDL_PAD_RGMII_RD0__GPIO6_IO25 0x2ac 0x694 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_RD1__HSI_TX_FLAG 0x2b0 0x698 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x2b0 0x698 0x81c 0x1 0x1
+#define MX6QDL_PAD_RGMII_RD1__GPIO6_IO27 0x2b0 0x698 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_RD2__HSI_TX_DATA 0x2b4 0x69c 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x2b4 0x69c 0x820 0x1 0x1
+#define MX6QDL_PAD_RGMII_RD2__GPIO6_IO28 0x2b4 0x69c 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_RD3__HSI_TX_WAKE 0x2b8 0x6a0 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x2b8 0x6a0 0x824 0x1 0x1
+#define MX6QDL_PAD_RGMII_RD3__GPIO6_IO29 0x2b8 0x6a0 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_RX_CTL__USB_H3_DATA 0x2bc 0x6a4 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x2bc 0x6a4 0x828 0x1 0x1
+#define MX6QDL_PAD_RGMII_RX_CTL__GPIO6_IO24 0x2bc 0x6a4 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_RXC__USB_H3_STROBE 0x2c0 0x6a8 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x2c0 0x6a8 0x814 0x1 0x1
+#define MX6QDL_PAD_RGMII_RXC__GPIO6_IO30 0x2c0 0x6a8 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TD0__HSI_TX_READY 0x2c4 0x6ac 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x2c4 0x6ac 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TD0__GPIO6_IO20 0x2c4 0x6ac 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TD1__HSI_RX_FLAG 0x2c8 0x6b0 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x2c8 0x6b0 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TD1__GPIO6_IO21 0x2c8 0x6b0 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TD2__HSI_RX_DATA 0x2cc 0x6b4 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x2cc 0x6b4 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TD2__GPIO6_IO22 0x2cc 0x6b4 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TD3__HSI_RX_WAKE 0x2d0 0x6b8 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x2d0 0x6b8 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TD3__GPIO6_IO23 0x2d0 0x6b8 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x2d4 0x6bc 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x2d4 0x6bc 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TX_CTL__GPIO6_IO26 0x2d4 0x6bc 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TX_CTL__ENET_REF_CLK 0x2d4 0x6bc 0x80c 0x7 0x1
+#define MX6QDL_PAD_RGMII_TXC__USB_H2_DATA 0x2d8 0x6c0 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x2d8 0x6c0 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TXC__SPDIF_EXT_CLK 0x2d8 0x6c0 0x8f4 0x2 0x1
+#define MX6QDL_PAD_RGMII_TXC__GPIO6_IO19 0x2d8 0x6c0 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TXC__XTALOSC_REF_CLK_24M 0x2d8 0x6c0 0x000 0x7 0x0
+#define MX6QDL_PAD_SD1_CLK__SD1_CLK 0x2dc 0x6c4 0x928 0x0 0x1
+#define MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT 0x2dc 0x6c4 0x000 0x2 0x0
+#define MX6QDL_PAD_SD1_CLK__GPT_CLKIN 0x2dc 0x6c4 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x2dc 0x6c4 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_CMD__SD1_CMD 0x2e0 0x6c8 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x2e0 0x6c8 0x000 0x2 0x0
+#define MX6QDL_PAD_SD1_CMD__GPT_COMPARE1 0x2e0 0x6c8 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_CMD__GPIO1_IO18 0x2e0 0x6c8 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x2e4 0x6cc 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_DAT0__GPT_CAPTURE1 0x2e4 0x6cc 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x2e4 0x6cc 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x2e8 0x6d0 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x2e8 0x6d0 0x000 0x2 0x0
+#define MX6QDL_PAD_SD1_DAT1__GPT_CAPTURE2 0x2e8 0x6d0 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x2e8 0x6d0 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x2ec 0x6d4 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_DAT2__GPT_COMPARE2 0x2ec 0x6d4 0x000 0x2 0x0
+#define MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x2ec 0x6d4 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_DAT2__WDOG1_B 0x2ec 0x6d4 0x000 0x4 0x0
+#define MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x2ec 0x6d4 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT2__WDOG1_RESET_B_DEB 0x2ec 0x6d4 0x000 0x6 0x0
+#define MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x2f0 0x6d8 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_DAT3__GPT_COMPARE3 0x2f0 0x6d8 0x000 0x2 0x0
+#define MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x2f0 0x6d8 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_DAT3__WDOG2_B 0x2f0 0x6d8 0x000 0x4 0x0
+#define MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x2f0 0x6d8 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT3__WDOG2_RESET_B_DEB 0x2f0 0x6d8 0x000 0x6 0x0
+#define MX6QDL_PAD_SD2_CLK__SD2_CLK 0x2f4 0x6dc 0x930 0x0 0x1
+#define MX6QDL_PAD_SD2_CLK__KEY_COL5 0x2f4 0x6dc 0x8c0 0x2 0x3
+#define MX6QDL_PAD_SD2_CLK__AUD4_RXFS 0x2f4 0x6dc 0x7a4 0x3 0x1
+#define MX6QDL_PAD_SD2_CLK__GPIO1_IO10 0x2f4 0x6dc 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_CMD__SD2_CMD 0x2f8 0x6e0 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_CMD__KEY_ROW5 0x2f8 0x6e0 0x8cc 0x2 0x2
+#define MX6QDL_PAD_SD2_CMD__AUD4_RXC 0x2f8 0x6e0 0x7a0 0x3 0x1
+#define MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x2f8 0x6e0 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x2fc 0x6e4 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x2fc 0x6e4 0x798 0x3 0x1
+#define MX6QDL_PAD_SD2_DAT0__KEY_ROW7 0x2fc 0x6e4 0x8d4 0x4 0x2
+#define MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x2fc 0x6e4 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_DAT0__DCIC2_OUT 0x2fc 0x6e4 0x000 0x6 0x0
+#define MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x300 0x6e8 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_DAT1__EIM_CS2_B 0x300 0x6e8 0x000 0x2 0x0
+#define MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x300 0x6e8 0x7ac 0x3 0x1
+#define MX6QDL_PAD_SD2_DAT1__KEY_COL7 0x300 0x6e8 0x8c8 0x4 0x2
+#define MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x300 0x6e8 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x304 0x6ec 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_DAT2__EIM_CS3_B 0x304 0x6ec 0x000 0x2 0x0
+#define MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x304 0x6ec 0x79c 0x3 0x1
+#define MX6QDL_PAD_SD2_DAT2__KEY_ROW6 0x304 0x6ec 0x8d0 0x4 0x2
+#define MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x304 0x6ec 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x308 0x6f0 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_DAT3__KEY_COL6 0x308 0x6f0 0x8c4 0x2 0x2
+#define MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x308 0x6f0 0x7a8 0x3 0x1
+#define MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x308 0x6f0 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_CLK__SD3_CLK 0x30c 0x6f4 0x934 0x0 0x1
+#define MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x30c 0x6f4 0x900 0x1 0x2
+#define MX6QDL_PAD_SD3_CLK__UART2_CTS_B 0x30c 0x6f4 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x30c 0x6f4 0x7c8 0x2 0x2
+#define MX6QDL_PAD_SD3_CLK__GPIO7_IO03 0x30c 0x6f4 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_CMD__SD3_CMD 0x310 0x6f8 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x310 0x6f8 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_CMD__UART2_RTS_B 0x310 0x6f8 0x900 0x1 0x3
+#define MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x310 0x6f8 0x000 0x2 0x0
+#define MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x310 0x6f8 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x314 0x6fc 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT0__UART1_CTS_B 0x314 0x6fc 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT0__UART1_RTS_B 0x314 0x6fc 0x8f8 0x1 0x2
+#define MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x314 0x6fc 0x000 0x2 0x0
+#define MX6QDL_PAD_SD3_DAT0__GPIO7_IO04 0x314 0x6fc 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x318 0x700 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT1__UART1_RTS_B 0x318 0x700 0x8f8 0x1 0x3
+#define MX6QDL_PAD_SD3_DAT1__UART1_CTS_B 0x318 0x700 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x318 0x700 0x7cc 0x2 0x1
+#define MX6QDL_PAD_SD3_DAT1__GPIO7_IO05 0x318 0x700 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x31c 0x704 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x31c 0x704 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x320 0x708 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT3__UART3_CTS_B 0x320 0x708 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT3__UART3_RTS_B 0x320 0x708 0x908 0x1 0x4
+#define MX6QDL_PAD_SD3_DAT3__GPIO7_IO07 0x320 0x708 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x324 0x70c 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x324 0x70c 0x904 0x1 0x4
+#define MX6QDL_PAD_SD3_DAT4__UART2_TX_DATA 0x324 0x70c 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x324 0x70c 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x328 0x710 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x328 0x710 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT5__UART2_RX_DATA 0x328 0x710 0x904 0x1 0x5
+#define MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x328 0x710 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x32c 0x714 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x32c 0x714 0x8fc 0x1 0x2
+#define MX6QDL_PAD_SD3_DAT6__UART1_TX_DATA 0x32c 0x714 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x32c 0x714 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x330 0x718 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x330 0x718 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT7__UART1_RX_DATA 0x330 0x718 0x8fc 0x1 0x3
+#define MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x330 0x718 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_RST__SD3_RESET 0x334 0x71c 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_RST__UART3_RTS_B 0x334 0x71c 0x908 0x1 0x5
+#define MX6QDL_PAD_SD3_RST__UART3_CTS_B 0x334 0x71c 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x334 0x71c 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_CLK__SD4_CLK 0x338 0x720 0x938 0x0 0x1
+#define MX6QDL_PAD_SD4_CLK__NAND_WE_B 0x338 0x720 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_CLK__UART3_RX_DATA 0x338 0x720 0x90c 0x2 0x2
+#define MX6QDL_PAD_SD4_CLK__UART3_TX_DATA 0x338 0x720 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_CLK__GPIO7_IO10 0x338 0x720 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_CMD__SD4_CMD 0x33c 0x724 0x000 0x0 0x0
+#define MX6QDL_PAD_SD4_CMD__NAND_RE_B 0x33c 0x724 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_CMD__UART3_TX_DATA 0x33c 0x724 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_CMD__UART3_RX_DATA 0x33c 0x724 0x90c 0x2 0x3
+#define MX6QDL_PAD_SD4_CMD__GPIO7_IO09 0x33c 0x724 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x340 0x728 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x340 0x728 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x340 0x728 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x344 0x72c 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x344 0x72c 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x344 0x72c 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x348 0x730 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x348 0x730 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x348 0x730 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x34c 0x734 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x34c 0x734 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x350 0x738 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x350 0x738 0x904 0x2 0x6
+#define MX6QDL_PAD_SD4_DAT4__UART2_TX_DATA 0x350 0x738 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x350 0x738 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x354 0x73c 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x354 0x73c 0x900 0x2 0x4
+#define MX6QDL_PAD_SD4_DAT5__UART2_CTS_B 0x354 0x73c 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT5__GPIO2_IO13 0x354 0x73c 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x358 0x740 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x358 0x740 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT6__UART2_RTS_B 0x358 0x740 0x900 0x2 0x5
+#define MX6QDL_PAD_SD4_DAT6__GPIO2_IO14 0x358 0x740 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x35c 0x744 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x35c 0x744 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA 0x35c 0x744 0x904 0x2 0x7
+#define MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x35c 0x744 0x000 0x5 0x0
+
+#endif /* __DTS_IMX6DL_PINFUNC_H */
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 11/21] dt-bindings: clock: imx6qdl: Add clock defines
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (9 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 10/21] arm: dts: imx6dl: Add pinctrl defines Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 12/21] arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo Jagan Teki
` (10 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add imx6qdl clock header defines support from Linux.
"clk: imx: Add clock support for imx6qp"
(sha1: ee36027427c769b0b9e5e205fe43aced93d6aa66)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
include/dt-bindings/clock/imx6qdl-clock.h | 274 ++++++++++++++++++++++++++++++
1 file changed, 274 insertions(+)
create mode 100644 include/dt-bindings/clock/imx6qdl-clock.h
diff --git a/include/dt-bindings/clock/imx6qdl-clock.h b/include/dt-bindings/clock/imx6qdl-clock.h
new file mode 100644
index 0000000..2905033
--- /dev/null
+++ b/include/dt-bindings/clock/imx6qdl-clock.h
@@ -0,0 +1,274 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_IMX6QDL_H
+#define __DT_BINDINGS_CLOCK_IMX6QDL_H
+
+#define IMX6QDL_CLK_DUMMY 0
+#define IMX6QDL_CLK_CKIL 1
+#define IMX6QDL_CLK_CKIH 2
+#define IMX6QDL_CLK_OSC 3
+#define IMX6QDL_CLK_PLL2_PFD0_352M 4
+#define IMX6QDL_CLK_PLL2_PFD1_594M 5
+#define IMX6QDL_CLK_PLL2_PFD2_396M 6
+#define IMX6QDL_CLK_PLL3_PFD0_720M 7
+#define IMX6QDL_CLK_PLL3_PFD1_540M 8
+#define IMX6QDL_CLK_PLL3_PFD2_508M 9
+#define IMX6QDL_CLK_PLL3_PFD3_454M 10
+#define IMX6QDL_CLK_PLL2_198M 11
+#define IMX6QDL_CLK_PLL3_120M 12
+#define IMX6QDL_CLK_PLL3_80M 13
+#define IMX6QDL_CLK_PLL3_60M 14
+#define IMX6QDL_CLK_TWD 15
+#define IMX6QDL_CLK_STEP 16
+#define IMX6QDL_CLK_PLL1_SW 17
+#define IMX6QDL_CLK_PERIPH_PRE 18
+#define IMX6QDL_CLK_PERIPH2_PRE 19
+#define IMX6QDL_CLK_PERIPH_CLK2_SEL 20
+#define IMX6QDL_CLK_PERIPH2_CLK2_SEL 21
+#define IMX6QDL_CLK_AXI_SEL 22
+#define IMX6QDL_CLK_ESAI_SEL 23
+#define IMX6QDL_CLK_ASRC_SEL 24
+#define IMX6QDL_CLK_SPDIF_SEL 25
+#define IMX6QDL_CLK_GPU2D_AXI 26
+#define IMX6QDL_CLK_GPU3D_AXI 27
+#define IMX6QDL_CLK_GPU2D_CORE_SEL 28
+#define IMX6QDL_CLK_GPU3D_CORE_SEL 29
+#define IMX6QDL_CLK_GPU3D_SHADER_SEL 30
+#define IMX6QDL_CLK_IPU1_SEL 31
+#define IMX6QDL_CLK_IPU2_SEL 32
+#define IMX6QDL_CLK_LDB_DI0_SEL 33
+#define IMX6QDL_CLK_LDB_DI1_SEL 34
+#define IMX6QDL_CLK_IPU1_DI0_PRE_SEL 35
+#define IMX6QDL_CLK_IPU1_DI1_PRE_SEL 36
+#define IMX6QDL_CLK_IPU2_DI0_PRE_SEL 37
+#define IMX6QDL_CLK_IPU2_DI1_PRE_SEL 38
+#define IMX6QDL_CLK_IPU1_DI0_SEL 39
+#define IMX6QDL_CLK_IPU1_DI1_SEL 40
+#define IMX6QDL_CLK_IPU2_DI0_SEL 41
+#define IMX6QDL_CLK_IPU2_DI1_SEL 42
+#define IMX6QDL_CLK_HSI_TX_SEL 43
+#define IMX6QDL_CLK_PCIE_AXI_SEL 44
+#define IMX6QDL_CLK_SSI1_SEL 45
+#define IMX6QDL_CLK_SSI2_SEL 46
+#define IMX6QDL_CLK_SSI3_SEL 47
+#define IMX6QDL_CLK_USDHC1_SEL 48
+#define IMX6QDL_CLK_USDHC2_SEL 49
+#define IMX6QDL_CLK_USDHC3_SEL 50
+#define IMX6QDL_CLK_USDHC4_SEL 51
+#define IMX6QDL_CLK_ENFC_SEL 52
+#define IMX6QDL_CLK_EIM_SEL 53
+#define IMX6QDL_CLK_EIM_SLOW_SEL 54
+#define IMX6QDL_CLK_VDO_AXI_SEL 55
+#define IMX6QDL_CLK_VPU_AXI_SEL 56
+#define IMX6QDL_CLK_CKO1_SEL 57
+#define IMX6QDL_CLK_PERIPH 58
+#define IMX6QDL_CLK_PERIPH2 59
+#define IMX6QDL_CLK_PERIPH_CLK2 60
+#define IMX6QDL_CLK_PERIPH2_CLK2 61
+#define IMX6QDL_CLK_IPG 62
+#define IMX6QDL_CLK_IPG_PER 63
+#define IMX6QDL_CLK_ESAI_PRED 64
+#define IMX6QDL_CLK_ESAI_PODF 65
+#define IMX6QDL_CLK_ASRC_PRED 66
+#define IMX6QDL_CLK_ASRC_PODF 67
+#define IMX6QDL_CLK_SPDIF_PRED 68
+#define IMX6QDL_CLK_SPDIF_PODF 69
+#define IMX6QDL_CLK_CAN_ROOT 70
+#define IMX6QDL_CLK_ECSPI_ROOT 71
+#define IMX6QDL_CLK_GPU2D_CORE_PODF 72
+#define IMX6QDL_CLK_GPU3D_CORE_PODF 73
+#define IMX6QDL_CLK_GPU3D_SHADER 74
+#define IMX6QDL_CLK_IPU1_PODF 75
+#define IMX6QDL_CLK_IPU2_PODF 76
+#define IMX6QDL_CLK_LDB_DI0_PODF 77
+#define IMX6QDL_CLK_LDB_DI1_PODF 78
+#define IMX6QDL_CLK_IPU1_DI0_PRE 79
+#define IMX6QDL_CLK_IPU1_DI1_PRE 80
+#define IMX6QDL_CLK_IPU2_DI0_PRE 81
+#define IMX6QDL_CLK_IPU2_DI1_PRE 82
+#define IMX6QDL_CLK_HSI_TX_PODF 83
+#define IMX6QDL_CLK_SSI1_PRED 84
+#define IMX6QDL_CLK_SSI1_PODF 85
+#define IMX6QDL_CLK_SSI2_PRED 86
+#define IMX6QDL_CLK_SSI2_PODF 87
+#define IMX6QDL_CLK_SSI3_PRED 88
+#define IMX6QDL_CLK_SSI3_PODF 89
+#define IMX6QDL_CLK_UART_SERIAL_PODF 90
+#define IMX6QDL_CLK_USDHC1_PODF 91
+#define IMX6QDL_CLK_USDHC2_PODF 92
+#define IMX6QDL_CLK_USDHC3_PODF 93
+#define IMX6QDL_CLK_USDHC4_PODF 94
+#define IMX6QDL_CLK_ENFC_PRED 95
+#define IMX6QDL_CLK_ENFC_PODF 96
+#define IMX6QDL_CLK_EIM_PODF 97
+#define IMX6QDL_CLK_EIM_SLOW_PODF 98
+#define IMX6QDL_CLK_VPU_AXI_PODF 99
+#define IMX6QDL_CLK_CKO1_PODF 100
+#define IMX6QDL_CLK_AXI 101
+#define IMX6QDL_CLK_MMDC_CH0_AXI_PODF 102
+#define IMX6QDL_CLK_MMDC_CH1_AXI_PODF 103
+#define IMX6QDL_CLK_ARM 104
+#define IMX6QDL_CLK_AHB 105
+#define IMX6QDL_CLK_APBH_DMA 106
+#define IMX6QDL_CLK_ASRC 107
+#define IMX6QDL_CLK_CAN1_IPG 108
+#define IMX6QDL_CLK_CAN1_SERIAL 109
+#define IMX6QDL_CLK_CAN2_IPG 110
+#define IMX6QDL_CLK_CAN2_SERIAL 111
+#define IMX6QDL_CLK_ECSPI1 112
+#define IMX6QDL_CLK_ECSPI2 113
+#define IMX6QDL_CLK_ECSPI3 114
+#define IMX6QDL_CLK_ECSPI4 115
+#define IMX6Q_CLK_ECSPI5 116
+#define IMX6DL_CLK_I2C4 116
+#define IMX6QDL_CLK_ENET 117
+#define IMX6QDL_CLK_ESAI_EXTAL 118
+#define IMX6QDL_CLK_GPT_IPG 119
+#define IMX6QDL_CLK_GPT_IPG_PER 120
+#define IMX6QDL_CLK_GPU2D_CORE 121
+#define IMX6QDL_CLK_GPU3D_CORE 122
+#define IMX6QDL_CLK_HDMI_IAHB 123
+#define IMX6QDL_CLK_HDMI_ISFR 124
+#define IMX6QDL_CLK_I2C1 125
+#define IMX6QDL_CLK_I2C2 126
+#define IMX6QDL_CLK_I2C3 127
+#define IMX6QDL_CLK_IIM 128
+#define IMX6QDL_CLK_ENFC 129
+#define IMX6QDL_CLK_IPU1 130
+#define IMX6QDL_CLK_IPU1_DI0 131
+#define IMX6QDL_CLK_IPU1_DI1 132
+#define IMX6QDL_CLK_IPU2 133
+#define IMX6QDL_CLK_IPU2_DI0 134
+#define IMX6QDL_CLK_LDB_DI0 135
+#define IMX6QDL_CLK_LDB_DI1 136
+#define IMX6QDL_CLK_IPU2_DI1 137
+#define IMX6QDL_CLK_HSI_TX 138
+#define IMX6QDL_CLK_MLB 139
+#define IMX6QDL_CLK_MMDC_CH0_AXI 140
+#define IMX6QDL_CLK_MMDC_CH1_AXI 141
+#define IMX6QDL_CLK_OCRAM 142
+#define IMX6QDL_CLK_OPENVG_AXI 143
+#define IMX6QDL_CLK_PCIE_AXI 144
+#define IMX6QDL_CLK_PWM1 145
+#define IMX6QDL_CLK_PWM2 146
+#define IMX6QDL_CLK_PWM3 147
+#define IMX6QDL_CLK_PWM4 148
+#define IMX6QDL_CLK_PER1_BCH 149
+#define IMX6QDL_CLK_GPMI_BCH_APB 150
+#define IMX6QDL_CLK_GPMI_BCH 151
+#define IMX6QDL_CLK_GPMI_IO 152
+#define IMX6QDL_CLK_GPMI_APB 153
+#define IMX6QDL_CLK_SATA 154
+#define IMX6QDL_CLK_SDMA 155
+#define IMX6QDL_CLK_SPBA 156
+#define IMX6QDL_CLK_SSI1 157
+#define IMX6QDL_CLK_SSI2 158
+#define IMX6QDL_CLK_SSI3 159
+#define IMX6QDL_CLK_UART_IPG 160
+#define IMX6QDL_CLK_UART_SERIAL 161
+#define IMX6QDL_CLK_USBOH3 162
+#define IMX6QDL_CLK_USDHC1 163
+#define IMX6QDL_CLK_USDHC2 164
+#define IMX6QDL_CLK_USDHC3 165
+#define IMX6QDL_CLK_USDHC4 166
+#define IMX6QDL_CLK_VDO_AXI 167
+#define IMX6QDL_CLK_VPU_AXI 168
+#define IMX6QDL_CLK_CKO1 169
+#define IMX6QDL_CLK_PLL1_SYS 170
+#define IMX6QDL_CLK_PLL2_BUS 171
+#define IMX6QDL_CLK_PLL3_USB_OTG 172
+#define IMX6QDL_CLK_PLL4_AUDIO 173
+#define IMX6QDL_CLK_PLL5_VIDEO 174
+#define IMX6QDL_CLK_PLL8_MLB 175
+#define IMX6QDL_CLK_PLL7_USB_HOST 176
+#define IMX6QDL_CLK_PLL6_ENET 177
+#define IMX6QDL_CLK_SSI1_IPG 178
+#define IMX6QDL_CLK_SSI2_IPG 179
+#define IMX6QDL_CLK_SSI3_IPG 180
+#define IMX6QDL_CLK_ROM 181
+#define IMX6QDL_CLK_USBPHY1 182
+#define IMX6QDL_CLK_USBPHY2 183
+#define IMX6QDL_CLK_LDB_DI0_DIV_3_5 184
+#define IMX6QDL_CLK_LDB_DI1_DIV_3_5 185
+#define IMX6QDL_CLK_SATA_REF 186
+#define IMX6QDL_CLK_SATA_REF_100M 187
+#define IMX6QDL_CLK_PCIE_REF 188
+#define IMX6QDL_CLK_PCIE_REF_125M 189
+#define IMX6QDL_CLK_ENET_REF 190
+#define IMX6QDL_CLK_USBPHY1_GATE 191
+#define IMX6QDL_CLK_USBPHY2_GATE 192
+#define IMX6QDL_CLK_PLL4_POST_DIV 193
+#define IMX6QDL_CLK_PLL5_POST_DIV 194
+#define IMX6QDL_CLK_PLL5_VIDEO_DIV 195
+#define IMX6QDL_CLK_EIM_SLOW 196
+#define IMX6QDL_CLK_SPDIF 197
+#define IMX6QDL_CLK_CKO2_SEL 198
+#define IMX6QDL_CLK_CKO2_PODF 199
+#define IMX6QDL_CLK_CKO2 200
+#define IMX6QDL_CLK_CKO 201
+#define IMX6QDL_CLK_VDOA 202
+#define IMX6QDL_CLK_PLL4_AUDIO_DIV 203
+#define IMX6QDL_CLK_LVDS1_SEL 204
+#define IMX6QDL_CLK_LVDS2_SEL 205
+#define IMX6QDL_CLK_LVDS1_GATE 206
+#define IMX6QDL_CLK_LVDS2_GATE 207
+#define IMX6QDL_CLK_ESAI_IPG 208
+#define IMX6QDL_CLK_ESAI_MEM 209
+#define IMX6QDL_CLK_ASRC_IPG 210
+#define IMX6QDL_CLK_ASRC_MEM 211
+#define IMX6QDL_CLK_LVDS1_IN 212
+#define IMX6QDL_CLK_LVDS2_IN 213
+#define IMX6QDL_CLK_ANACLK1 214
+#define IMX6QDL_CLK_ANACLK2 215
+#define IMX6QDL_PLL1_BYPASS_SRC 216
+#define IMX6QDL_PLL2_BYPASS_SRC 217
+#define IMX6QDL_PLL3_BYPASS_SRC 218
+#define IMX6QDL_PLL4_BYPASS_SRC 219
+#define IMX6QDL_PLL5_BYPASS_SRC 220
+#define IMX6QDL_PLL6_BYPASS_SRC 221
+#define IMX6QDL_PLL7_BYPASS_SRC 222
+#define IMX6QDL_CLK_PLL1 223
+#define IMX6QDL_CLK_PLL2 224
+#define IMX6QDL_CLK_PLL3 225
+#define IMX6QDL_CLK_PLL4 226
+#define IMX6QDL_CLK_PLL5 227
+#define IMX6QDL_CLK_PLL6 228
+#define IMX6QDL_CLK_PLL7 229
+#define IMX6QDL_PLL1_BYPASS 230
+#define IMX6QDL_PLL2_BYPASS 231
+#define IMX6QDL_PLL3_BYPASS 232
+#define IMX6QDL_PLL4_BYPASS 233
+#define IMX6QDL_PLL5_BYPASS 234
+#define IMX6QDL_PLL6_BYPASS 235
+#define IMX6QDL_PLL7_BYPASS 236
+#define IMX6QDL_CLK_GPT_3M 237
+#define IMX6QDL_CLK_VIDEO_27M 238
+#define IMX6QDL_CLK_MIPI_CORE_CFG 239
+#define IMX6QDL_CLK_MIPI_IPG 240
+#define IMX6QDL_CLK_CAAM_MEM 241
+#define IMX6QDL_CLK_CAAM_ACLK 242
+#define IMX6QDL_CLK_CAAM_IPG 243
+#define IMX6QDL_CLK_SPDIF_GCLK 244
+#define IMX6QDL_CLK_UART_SEL 245
+#define IMX6QDL_CLK_IPG_PER_SEL 246
+#define IMX6QDL_CLK_ECSPI_SEL 247
+#define IMX6QDL_CLK_CAN_SEL 248
+#define IMX6QDL_CLK_MMDC_CH1_AXI_CG 249
+#define IMX6QDL_CLK_PRE0 250
+#define IMX6QDL_CLK_PRE1 251
+#define IMX6QDL_CLK_PRE2 252
+#define IMX6QDL_CLK_PRE3 253
+#define IMX6QDL_CLK_PRG0_AXI 254
+#define IMX6QDL_CLK_PRG1_AXI 255
+#define IMX6QDL_CLK_PRG0_APB 256
+#define IMX6QDL_CLK_PRG1_APB 257
+#define IMX6QDL_CLK_PRE_AXI 258
+#define IMX6QDL_CLK_END 259
+
+#endif /* __DT_BINDINGS_CLOCK_IMX6QDL_H */
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 12/21] arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (10 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 11/21] dt-bindings: clock: imx6qdl: Add clock defines Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 13/21] imx6q: icorem6: Enable pinctrl driver Jagan Teki
` (9 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DL, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/cpu/armv7/mx6/Kconfig | 1 +
arch/arm/dts/Makefile | 3 +-
arch/arm/dts/imx6dl-icore.dts | 59 +++++++++++
arch/arm/dts/imx6qdl-icore.dtsi | 196 ++++++++++++++++++++++++++++++++++++
board/engicam/icorem6/README | 6 +-
configs/imx6qdl_icore_mmc_defconfig | 1 +
6 files changed, 262 insertions(+), 4 deletions(-)
create mode 100644 arch/arm/dts/imx6dl-icore.dts
create mode 100644 arch/arm/dts/imx6qdl-icore.dtsi
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index 5d549bd..e2431a8 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -98,6 +98,7 @@ config TARGET_MX6QARM2
config TARGET_MX6Q_ICORE
bool "Support Engicam i.Core"
select MX6QDL
+ select OF_CONTROL
select DM
select DM_THERMAL
select SUPPORT_SPL
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 532527d..1994fc8 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -281,7 +281,8 @@ dtb-$(CONFIG_VF610) += vf500-colibri.dtb \
pcm052.dtb \
bk4r1.dtb
-dtb-$(CONFIG_MX6) += imx6ull-14x14-evk.dtb
+dtb-$(CONFIG_MX6) += imx6ull-14x14-evk.dtb \
+ imx6dl-icore.dtb
dtb-$(CONFIG_MX7) += imx7-colibri.dtb
diff --git a/arch/arm/dts/imx6dl-icore.dts b/arch/arm/dts/imx6dl-icore.dts
new file mode 100644
index 0000000..aec332c
--- /dev/null
+++ b/arch/arm/dts/imx6dl-icore.dts
@@ -0,0 +1,59 @@
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-icore.dtsi"
+
+/ {
+ model = "Engicam i.CoreM6 DualLite/Solo Starter Kit";
+ compatible = "engicam,imx6-icore", "fsl,imx6dl";
+};
+
+&can1 {
+ status = "okay";
+};
+
+&can2 {
+ status = "okay";
+};
diff --git a/arch/arm/dts/imx6qdl-icore.dtsi b/arch/arm/dts/imx6qdl-icore.dtsi
new file mode 100644
index 0000000..f424cd5
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-icore.dtsi
@@ -0,0 +1,196 @@
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ memory {
+ reg = <0x10000000 0x80000000>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_3p3v>;
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_3p3v>;
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LVDS2_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_OSC>;
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b020
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b020
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b020
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b020
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpmi-nand {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17070
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10070
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17070
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17070
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17070
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17070
+ >;
+ };
+};
diff --git a/board/engicam/icorem6/README b/board/engicam/icorem6/README
index cf2eff2..c264a94 100644
--- a/board/engicam/icorem6/README
+++ b/board/engicam/icorem6/README
@@ -7,15 +7,15 @@ $ make mrproper
$ make icorem6qdl_mmc_defconfig
$ make
-This will generate the SPL image called SPL and the u-boot.img.
+This will generate the SPL image called SPL and the u-boot-dtb.img.
- Flash the SPL image into the micro SD card:
sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
-- Flash the u-boot.img image into the micro SD card:
+- Flash the u-boot-dtb.img image into the micro SD card:
-sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69; sync
+sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync
- Jumper settings:
diff --git a/configs/imx6qdl_icore_mmc_defconfig b/configs/imx6qdl_icore_mmc_defconfig
index c2c2fe8..6786daf 100644
--- a/configs/imx6qdl_icore_mmc_defconfig
+++ b/configs/imx6qdl_icore_mmc_defconfig
@@ -3,6 +3,7 @@ CONFIG_ARCH_MX6=y
CONFIG_TARGET_MX6Q_ICORE=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,ENV_IS_IN_MMC"
CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
CONFIG_SYS_PROMPT="icorem6qdl> "
CONFIG_SPL=y
CONFIG_BOOTDELAY=3
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 13/21] imx6q: icorem6: Enable pinctrl driver
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (11 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 12/21] arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 14/21] engicam: icorem6: Add DM_GPIO, DM_MMC support Jagan Teki
` (8 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Enable imx6 pinctrl driver support for i.CoreM6.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
configs/imx6qdl_icore_mmc_defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/configs/imx6qdl_icore_mmc_defconfig b/configs/imx6qdl_icore_mmc_defconfig
index 6786daf..221ea7e 100644
--- a/configs/imx6qdl_icore_mmc_defconfig
+++ b/configs/imx6qdl_icore_mmc_defconfig
@@ -30,6 +30,8 @@ CONFIG_FEC_MXC=y
CONFIG_MXC_UART=y
CONFIG_NETDEVICES=y
CONFIG_IMX_THERMAL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 14/21] engicam: icorem6: Add DM_GPIO, DM_MMC support
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (12 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 13/21] imx6q: icorem6: Enable pinctrl driver Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 15/21] arm: dts: Add devicetree for i.MX6Q Jagan Teki
` (7 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/cpu/armv7/mx6/Kconfig | 2 +
board/engicam/icorem6/icorem6.c | 142 ++++++++++++++++++++--------------------
include/configs/imx6qdl_icore.h | 4 ++
3 files changed, 78 insertions(+), 70 deletions(-)
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index e2431a8..762a581 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -100,6 +100,8 @@ config TARGET_MX6Q_ICORE
select MX6QDL
select OF_CONTROL
select DM
+ select DM_GPIO
+ select DM_MMC
select DM_THERMAL
select SUPPORT_SPL
diff --git a/board/engicam/icorem6/icorem6.c b/board/engicam/icorem6/icorem6.c
index a23cb7e..a370c8b 100644
--- a/board/engicam/icorem6/icorem6.c
+++ b/board/engicam/icorem6/icorem6.c
@@ -7,8 +7,6 @@
*/
#include <common.h>
-#include <fsl_esdhc.h>
-#include <mmc.h>
#include <miiphy.h>
#include <netdev.h>
@@ -29,10 +27,6 @@ DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
- PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
@@ -55,70 +49,6 @@ static iomux_v3_cfg_t const enet_pads[] = {
IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
-static iomux_v3_cfg_t const usdhc1_pads[] = {
- IOMUX_PADS(PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL)),/* CD */
-};
-
-#ifdef CONFIG_FSL_ESDHC
-#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 1)
-
-struct fsl_esdhc_cfg usdhc_cfg[1] = {
- {USDHC1_BASE_ADDR, 0, 4},
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC1_BASE_ADDR:
- ret = !gpio_get_value(USDHC1_CD_GPIO);
- break;
- }
-
- return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- int i, ret;
-
- /*
- * According to the board_mmc_init() the following map is done:
- * (U-boot device node) (Physical Port)
- * mmc0 USDHC1
- */
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- switch (i) {
- case 0:
- SETUP_IOMUX_PADS(usdhc1_pads);
- gpio_direction_input(USDHC1_CD_GPIO);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- break;
- default:
- printf("Warning - USDHC%d controller not supporting\n",
- i + 1);
- return 0;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- if (ret) {
- printf("Warning: failed to initialize mmc dev %d\n", i);
- return ret;
- }
- }
-
- return 0;
-}
-#endif
-
#ifdef CONFIG_FEC_MXC
#define ENET_PHY_RST IMX_GPIO_NR(7, 12)
static int setup_fec(void)
@@ -200,6 +130,78 @@ int dram_init(void)
#include <asm/arch/crm_regs.h>
#include <asm/arch/mx6-ddr.h>
+/* MMC board initialization is needed till adding DM support in SPL */
+#if defined(CONFIG_FSL_ESDHC) && !defined(CONFIG_DM_MMC)
+#include <mmc.h>
+#include <fsl_esdhc.h>
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+ IOMUX_PADS(PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL)),/* CD */
+};
+
+#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 1)
+
+struct fsl_esdhc_cfg usdhc_cfg[1] = {
+ {USDHC1_BASE_ADDR, 0, 4},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = !gpio_get_value(USDHC1_CD_GPIO);
+ break;
+ }
+
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int i, ret;
+
+ /*
+ * According to the board_mmc_init() the following map is done:
+ * (U-boot device node) (Physical Port)
+ * mmc0 USDHC1
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ SETUP_IOMUX_PADS(usdhc1_pads);
+ gpio_direction_input(USDHC1_CD_GPIO);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+ default:
+ printf("Warning - USDHC%d controller not supporting\n",
+ i + 1);
+ return 0;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret) {
+ printf("Warning: failed to initialize mmc dev %d\n", i);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+#endif
+
/*
* Driving strength:
* 0x30 == 40 Ohm
diff --git a/include/configs/imx6qdl_icore.h b/include/configs/imx6qdl_icore.h
index ad4c5f2..6b58447 100644
--- a/include/configs/imx6qdl_icore.h
+++ b/include/configs/imx6qdl_icore.h
@@ -127,6 +127,10 @@
#ifdef CONFIG_SPL
# define CONFIG_SPL_MMC_SUPPORT
# include "imx6_spl.h"
+# ifdef CONFIG_SPL_BUILD
+# undef CONFIG_DM_GPIO
+# undef CONFIG_DM_MMC
+# endif
#endif
#endif /* __IMX6QLD_ICORE_CONFIG_H */
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 15/21] arm: dts: Add devicetree for i.MX6Q
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (13 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 14/21] engicam: icorem6: Add DM_GPIO, DM_MMC support Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 16/21] arm: dts: imx6q: Add pinctrl defines Jagan Teki
` (6 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add i.MX6Q dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/imx6q.dtsi | 300 ++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 300 insertions(+)
create mode 100644 arch/arm/dts/imx6q.dtsi
diff --git a/arch/arm/dts/imx6q.dtsi b/arch/arm/dts/imx6q.dtsi
new file mode 100644
index 0000000..c30c836
--- /dev/null
+++ b/arch/arm/dts/imx6q.dtsi
@@ -0,0 +1,300 @@
+
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q-pinfunc.h"
+#include "imx6qdl.dtsi"
+
+/ {
+ aliases {
+ ipu1 = &ipu2;
+ spi4 = &ecspi5;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu at 0 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ operating-points = <
+ /* kHz uV */
+ 1200000 1275000
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 975000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC-PU uV */
+ 1200000 1275000
+ 996000 1250000
+ 852000 1250000
+ 792000 1175000
+ 396000 1175000
+ >;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clks IMX6QDL_CLK_ARM>,
+ <&clks IMX6QDL_CLK_PLL2_PFD2_396M>,
+ <&clks IMX6QDL_CLK_STEP>,
+ <&clks IMX6QDL_CLK_PLL1_SW>,
+ <&clks IMX6QDL_CLK_PLL1_SYS>;
+ clock-names = "arm", "pll2_pfd2_396m", "step",
+ "pll1_sw", "pll1_sys";
+ arm-supply = <®_arm>;
+ pu-supply = <®_pu>;
+ soc-supply = <®_soc>;
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <2>;
+ next-level-cache = <&L2>;
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <3>;
+ next-level-cache = <&L2>;
+ };
+ };
+
+ soc {
+ ocram: sram at 00900000 {
+ compatible = "mmio-sram";
+ reg = <0x00900000 0x40000>;
+ clocks = <&clks IMX6QDL_CLK_OCRAM>;
+ };
+
+ aips-bus at 02000000 { /* AIPS1 */
+ spba-bus at 02000000 {
+ ecspi5: ecspi at 02018000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02018000 0x4000>;
+ interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6Q_CLK_ECSPI5>,
+ <&clks IMX6Q_CLK_ECSPI5>;
+ clock-names = "ipg", "per";
+ dmas = <&sdma 11 7 1>, <&sdma 12 7 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+ };
+
+ iomuxc: iomuxc at 020e0000 {
+ compatible = "fsl,imx6q-iomuxc";
+ };
+ };
+
+ sata: sata at 02200000 {
+ compatible = "fsl,imx6q-ahci";
+ reg = <0x02200000 0x4000>;
+ interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_SATA>,
+ <&clks IMX6QDL_CLK_SATA_REF_100M>,
+ <&clks IMX6QDL_CLK_AHB>;
+ clock-names = "sata", "sata_ref", "ahb";
+ status = "disabled";
+ };
+
+ gpu_vg: gpu at 02204000 {
+ compatible = "vivante,gc";
+ reg = <0x02204000 0x4000>;
+ interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_OPENVG_AXI>,
+ <&clks IMX6QDL_CLK_GPU2D_CORE>;
+ clock-names = "bus", "core";
+ power-domains = <&gpc 1>;
+ };
+
+ ipu2: ipu at 02800000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ipu";
+ reg = <0x02800000 0x400000>;
+ interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>,
+ <0 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_IPU2>,
+ <&clks IMX6QDL_CLK_IPU2_DI0>,
+ <&clks IMX6QDL_CLK_IPU2_DI1>;
+ clock-names = "bus", "di0", "di1";
+ resets = <&src 4>;
+
+ ipu2_csi0: port at 0 {
+ reg = <0>;
+ };
+
+ ipu2_csi1: port at 1 {
+ reg = <1>;
+ };
+
+ ipu2_di0: port at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+
+ ipu2_di0_disp0: disp0-endpoint {
+ };
+
+ ipu2_di0_hdmi: hdmi-endpoint {
+ remote-endpoint = <&hdmi_mux_2>;
+ };
+
+ ipu2_di0_mipi: mipi-endpoint {
+ remote-endpoint = <&mipi_mux_2>;
+ };
+
+ ipu2_di0_lvds0: lvds0-endpoint {
+ remote-endpoint = <&lvds0_mux_2>;
+ };
+
+ ipu2_di0_lvds1: lvds1-endpoint {
+ remote-endpoint = <&lvds1_mux_2>;
+ };
+ };
+
+ ipu2_di1: port at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ ipu2_di1_hdmi: hdmi-endpoint {
+ remote-endpoint = <&hdmi_mux_3>;
+ };
+
+ ipu2_di1_mipi: mipi-endpoint {
+ remote-endpoint = <&mipi_mux_3>;
+ };
+
+ ipu2_di1_lvds0: lvds0-endpoint {
+ remote-endpoint = <&lvds0_mux_3>;
+ };
+
+ ipu2_di1_lvds1: lvds1-endpoint {
+ remote-endpoint = <&lvds1_mux_3>;
+ };
+ };
+ };
+ };
+
+ display-subsystem {
+ compatible = "fsl,imx-display-subsystem";
+ ports = <&ipu1_di0>, <&ipu1_di1>, <&ipu2_di0>, <&ipu2_di1>;
+ };
+
+ gpu-subsystem {
+ compatible = "fsl,imx-gpu-subsystem";
+ cores = <&gpu_2d>, <&gpu_3d>, <&gpu_vg>;
+ };
+};
+
+&hdmi {
+ compatible = "fsl,imx6q-hdmi";
+
+ port at 2 {
+ reg = <2>;
+
+ hdmi_mux_2: endpoint {
+ remote-endpoint = <&ipu2_di0_hdmi>;
+ };
+ };
+
+ port at 3 {
+ reg = <3>;
+
+ hdmi_mux_3: endpoint {
+ remote-endpoint = <&ipu2_di1_hdmi>;
+ };
+ };
+};
+
+&ldb {
+ clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+ <&clks IMX6QDL_CLK_IPU1_DI0_SEL>, <&clks IMX6QDL_CLK_IPU1_DI1_SEL>,
+ <&clks IMX6QDL_CLK_IPU2_DI0_SEL>, <&clks IMX6QDL_CLK_IPU2_DI1_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI0>, <&clks IMX6QDL_CLK_LDB_DI1>;
+ clock-names = "di0_pll", "di1_pll",
+ "di0_sel", "di1_sel", "di2_sel", "di3_sel",
+ "di0", "di1";
+
+ lvds-channel at 0 {
+ port at 2 {
+ reg = <2>;
+
+ lvds0_mux_2: endpoint {
+ remote-endpoint = <&ipu2_di0_lvds0>;
+ };
+ };
+
+ port at 3 {
+ reg = <3>;
+
+ lvds0_mux_3: endpoint {
+ remote-endpoint = <&ipu2_di1_lvds0>;
+ };
+ };
+ };
+
+ lvds-channel at 1 {
+ port at 2 {
+ reg = <2>;
+
+ lvds1_mux_2: endpoint {
+ remote-endpoint = <&ipu2_di0_lvds1>;
+ };
+ };
+
+ port at 3 {
+ reg = <3>;
+
+ lvds1_mux_3: endpoint {
+ remote-endpoint = <&ipu2_di1_lvds1>;
+ };
+ };
+ };
+};
+
+&mipi_dsi {
+ ports {
+ port at 2 {
+ reg = <2>;
+
+ mipi_mux_2: endpoint {
+ remote-endpoint = <&ipu2_di0_mipi>;
+ };
+ };
+
+ port at 3 {
+ reg = <3>;
+
+ mipi_mux_3: endpoint {
+ remote-endpoint = <&ipu2_di1_mipi>;
+ };
+ };
+ };
+};
+
+&vpu {
+ compatible = "fsl,imx6q-vpu", "cnm,coda960";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 16/21] arm: dts: imx6q: Add pinctrl defines
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (14 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 15/21] arm: dts: Add devicetree for i.MX6Q Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 17/21] arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual Jagan Teki
` (5 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add imx6q pinctrl defines support from Linux.
Here is the last commit:
"ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ"
(sha1: d8c765e0d1ddbd5032c2491c82cc9660c2f0e7f2)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/imx6q-pinfunc.h | 1047 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 1047 insertions(+)
create mode 100644 arch/arm/dts/imx6q-pinfunc.h
diff --git a/arch/arm/dts/imx6q-pinfunc.h b/arch/arm/dts/imx6q-pinfunc.h
new file mode 100644
index 0000000..9fc6120
--- /dev/null
+++ b/arch/arm/dts/imx6q-pinfunc.h
@@ -0,0 +1,1047 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __DTS_IMX6Q_PINFUNC_H
+#define __DTS_IMX6Q_PINFUNC_H
+
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+#define MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x04c 0x360 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_DAT1__ECSPI5_SS0 0x04c 0x360 0x834 0x1 0x0
+#define MX6QDL_PAD_SD2_DAT1__EIM_CS2_B 0x04c 0x360 0x000 0x2 0x0
+#define MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x04c 0x360 0x7c8 0x3 0x0
+#define MX6QDL_PAD_SD2_DAT1__KEY_COL7 0x04c 0x360 0x8f0 0x4 0x0
+#define MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x04c 0x360 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x050 0x364 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_DAT2__ECSPI5_SS1 0x050 0x364 0x838 0x1 0x0
+#define MX6QDL_PAD_SD2_DAT2__EIM_CS3_B 0x050 0x364 0x000 0x2 0x0
+#define MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x050 0x364 0x7b8 0x3 0x0
+#define MX6QDL_PAD_SD2_DAT2__KEY_ROW6 0x050 0x364 0x8f8 0x4 0x0
+#define MX6QDL_PAD_SD2_DAT2__GPIO1_IO13 0x050 0x364 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x054 0x368 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_DAT0__ECSPI5_MISO 0x054 0x368 0x82c 0x1 0x0
+#define MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x054 0x368 0x7b4 0x3 0x0
+#define MX6QDL_PAD_SD2_DAT0__KEY_ROW7 0x054 0x368 0x8fc 0x4 0x0
+#define MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x054 0x368 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_DAT0__DCIC2_OUT 0x054 0x368 0x000 0x6 0x0
+#define MX6QDL_PAD_RGMII_TXC__USB_H2_DATA 0x058 0x36c 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x058 0x36c 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TXC__SPDIF_EXT_CLK 0x058 0x36c 0x918 0x2 0x0
+#define MX6QDL_PAD_RGMII_TXC__GPIO6_IO19 0x058 0x36c 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TXC__XTALOSC_REF_CLK_24M 0x058 0x36c 0x000 0x7 0x0
+#define MX6QDL_PAD_RGMII_TD0__HSI_TX_READY 0x05c 0x370 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x05c 0x370 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TD0__GPIO6_IO20 0x05c 0x370 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TD1__HSI_RX_FLAG 0x060 0x374 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x060 0x374 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TD1__GPIO6_IO21 0x060 0x374 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TD2__HSI_RX_DATA 0x064 0x378 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x064 0x378 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TD2__GPIO6_IO22 0x064 0x378 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TD3__HSI_RX_WAKE 0x068 0x37c 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x068 0x37c 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TD3__GPIO6_IO23 0x068 0x37c 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_RX_CTL__USB_H3_DATA 0x06c 0x380 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x06c 0x380 0x858 0x1 0x0
+#define MX6QDL_PAD_RGMII_RX_CTL__GPIO6_IO24 0x06c 0x380 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_RD0__HSI_RX_READY 0x070 0x384 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x070 0x384 0x848 0x1 0x0
+#define MX6QDL_PAD_RGMII_RD0__GPIO6_IO25 0x070 0x384 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x074 0x388 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x074 0x388 0x000 0x1 0x0
+#define MX6QDL_PAD_RGMII_TX_CTL__GPIO6_IO26 0x074 0x388 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_TX_CTL__ENET_REF_CLK 0x074 0x388 0x83c 0x7 0x0
+#define MX6QDL_PAD_RGMII_RD1__HSI_TX_FLAG 0x078 0x38c 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x078 0x38c 0x84c 0x1 0x0
+#define MX6QDL_PAD_RGMII_RD1__GPIO6_IO27 0x078 0x38c 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_RD2__HSI_TX_DATA 0x07c 0x390 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x07c 0x390 0x850 0x1 0x0
+#define MX6QDL_PAD_RGMII_RD2__GPIO6_IO28 0x07c 0x390 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_RD3__HSI_TX_WAKE 0x080 0x394 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x080 0x394 0x854 0x1 0x0
+#define MX6QDL_PAD_RGMII_RD3__GPIO6_IO29 0x080 0x394 0x000 0x5 0x0
+#define MX6QDL_PAD_RGMII_RXC__USB_H3_STROBE 0x084 0x398 0x000 0x0 0x0
+#define MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x084 0x398 0x844 0x1 0x0
+#define MX6QDL_PAD_RGMII_RXC__GPIO6_IO30 0x084 0x398 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A25__EIM_ADDR25 0x088 0x39c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A25__ECSPI4_SS1 0x088 0x39c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A25__ECSPI2_RDY 0x088 0x39c 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_A25__IPU1_DI1_PIN12 0x088 0x39c 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_A25__IPU1_DI0_D1_CS 0x088 0x39c 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x088 0x39c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x088 0x39c 0x88c 0x6 0x0
+#define MX6QDL_PAD_EIM_EB2__EIM_EB2_B 0x08c 0x3a0 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_EB2__ECSPI1_SS0 0x08c 0x3a0 0x800 0x1 0x0
+#define MX6QDL_PAD_EIM_EB2__IPU2_CSI1_DATA19 0x08c 0x3a0 0x8d4 0x3 0x0
+#define MX6QDL_PAD_EIM_EB2__HDMI_TX_DDC_SCL 0x08c 0x3a0 0x890 0x4 0x0
+#define MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x08c 0x3a0 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x08c 0x3a0 0x8a0 0x6 0x0
+#define MX6QDL_PAD_EIM_EB2__SRC_BOOT_CFG30 0x08c 0x3a0 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D16__EIM_DATA16 0x090 0x3a4 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x090 0x3a4 0x7f4 0x1 0x0
+#define MX6QDL_PAD_EIM_D16__IPU1_DI0_PIN05 0x090 0x3a4 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D16__IPU2_CSI1_DATA18 0x090 0x3a4 0x8d0 0x3 0x0
+#define MX6QDL_PAD_EIM_D16__HDMI_TX_DDC_SDA 0x090 0x3a4 0x894 0x4 0x0
+#define MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x090 0x3a4 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D16__I2C2_SDA 0x090 0x3a4 0x8a4 0x6 0x0
+#define MX6QDL_PAD_EIM_D17__EIM_DATA17 0x094 0x3a8 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x094 0x3a8 0x7f8 0x1 0x0
+#define MX6QDL_PAD_EIM_D17__IPU1_DI0_PIN06 0x094 0x3a8 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D17__IPU2_CSI1_PIXCLK 0x094 0x3a8 0x8e0 0x3 0x0
+#define MX6QDL_PAD_EIM_D17__DCIC1_OUT 0x094 0x3a8 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D17__GPIO3_IO17 0x094 0x3a8 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D17__I2C3_SCL 0x094 0x3a8 0x8a8 0x6 0x0
+#define MX6QDL_PAD_EIM_D18__EIM_DATA18 0x098 0x3ac 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x098 0x3ac 0x7fc 0x1 0x0
+#define MX6QDL_PAD_EIM_D18__IPU1_DI0_PIN07 0x098 0x3ac 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D18__IPU2_CSI1_DATA17 0x098 0x3ac 0x8cc 0x3 0x0
+#define MX6QDL_PAD_EIM_D18__IPU1_DI1_D0_CS 0x098 0x3ac 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x098 0x3ac 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D18__I2C3_SDA 0x098 0x3ac 0x8ac 0x6 0x0
+#define MX6QDL_PAD_EIM_D19__EIM_DATA19 0x09c 0x3b0 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D19__ECSPI1_SS1 0x09c 0x3b0 0x804 0x1 0x0
+#define MX6QDL_PAD_EIM_D19__IPU1_DI0_PIN08 0x09c 0x3b0 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D19__IPU2_CSI1_DATA16 0x09c 0x3b0 0x8c8 0x3 0x0
+#define MX6QDL_PAD_EIM_D19__UART1_CTS_B 0x09c 0x3b0 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D19__UART1_RTS_B 0x09c 0x3b0 0x91c 0x4 0x0
+#define MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x09c 0x3b0 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D19__EPIT1_OUT 0x09c 0x3b0 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D20__EIM_DATA20 0x0a0 0x3b4 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D20__ECSPI4_SS0 0x0a0 0x3b4 0x824 0x1 0x0
+#define MX6QDL_PAD_EIM_D20__IPU1_DI0_PIN16 0x0a0 0x3b4 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D20__IPU2_CSI1_DATA15 0x0a0 0x3b4 0x8c4 0x3 0x0
+#define MX6QDL_PAD_EIM_D20__UART1_RTS_B 0x0a0 0x3b4 0x91c 0x4 0x1
+#define MX6QDL_PAD_EIM_D20__UART1_CTS_B 0x0a0 0x3b4 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x0a0 0x3b4 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D20__EPIT2_OUT 0x0a0 0x3b4 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D21__EIM_DATA21 0x0a4 0x3b8 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x0a4 0x3b8 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D21__IPU1_DI0_PIN17 0x0a4 0x3b8 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D21__IPU2_CSI1_DATA11 0x0a4 0x3b8 0x8b4 0x3 0x0
+#define MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x0a4 0x3b8 0x944 0x4 0x0
+#define MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x0a4 0x3b8 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D21__I2C1_SCL 0x0a4 0x3b8 0x898 0x6 0x0
+#define MX6QDL_PAD_EIM_D21__SPDIF_IN 0x0a4 0x3b8 0x914 0x7 0x0
+#define MX6QDL_PAD_EIM_D22__EIM_DATA22 0x0a8 0x3bc 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x0a8 0x3bc 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D22__IPU1_DI0_PIN01 0x0a8 0x3bc 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D22__IPU2_CSI1_DATA10 0x0a8 0x3bc 0x8b0 0x3 0x0
+#define MX6QDL_PAD_EIM_D22__USB_OTG_PWR 0x0a8 0x3bc 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0a8 0x3bc 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D22__SPDIF_OUT 0x0a8 0x3bc 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D23__EIM_DATA23 0x0ac 0x3c0 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D23__IPU1_DI0_D0_CS 0x0ac 0x3c0 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x0ac 0x3c0 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D23__UART3_RTS_B 0x0ac 0x3c0 0x92c 0x2 0x0
+#define MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x0ac 0x3c0 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_D23__IPU2_CSI1_DATA_EN 0x0ac 0x3c0 0x8d8 0x4 0x0
+#define MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x0ac 0x3c0 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D23__IPU1_DI1_PIN02 0x0ac 0x3c0 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D23__IPU1_DI1_PIN14 0x0ac 0x3c0 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_EB3__EIM_EB3_B 0x0b0 0x3c4 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_EB3__ECSPI4_RDY 0x0b0 0x3c4 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x0b0 0x3c4 0x92c 0x2 0x1
+#define MX6QDL_PAD_EIM_EB3__UART3_CTS_B 0x0b0 0x3c4 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_EB3__UART1_RI_B 0x0b0 0x3c4 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_EB3__IPU2_CSI1_HSYNC 0x0b0 0x3c4 0x8dc 0x4 0x0
+#define MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x0b0 0x3c4 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_EB3__IPU1_DI1_PIN03 0x0b0 0x3c4 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_EB3__SRC_BOOT_CFG31 0x0b0 0x3c4 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D24__EIM_DATA24 0x0b4 0x3c8 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D24__ECSPI4_SS2 0x0b4 0x3c8 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x0b4 0x3c8 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D24__UART3_RX_DATA 0x0b4 0x3c8 0x930 0x2 0x0
+#define MX6QDL_PAD_EIM_D24__ECSPI1_SS2 0x0b4 0x3c8 0x808 0x3 0x0
+#define MX6QDL_PAD_EIM_D24__ECSPI2_SS2 0x0b4 0x3c8 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x0b4 0x3c8 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D24__AUD5_RXFS 0x0b4 0x3c8 0x7d8 0x6 0x0
+#define MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x0b4 0x3c8 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D25__EIM_DATA25 0x0b8 0x3cc 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D25__ECSPI4_SS3 0x0b8 0x3cc 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x0b8 0x3cc 0x930 0x2 0x1
+#define MX6QDL_PAD_EIM_D25__UART3_TX_DATA 0x0b8 0x3cc 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D25__ECSPI1_SS3 0x0b8 0x3cc 0x80c 0x3 0x0
+#define MX6QDL_PAD_EIM_D25__ECSPI2_SS3 0x0b8 0x3cc 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x0b8 0x3cc 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D25__AUD5_RXC 0x0b8 0x3cc 0x7d4 0x6 0x0
+#define MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x0b8 0x3cc 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D26__EIM_DATA26 0x0bc 0x3d0 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D26__IPU1_DI1_PIN11 0x0bc 0x3d0 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D26__IPU1_CSI0_DATA01 0x0bc 0x3d0 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D26__IPU2_CSI1_DATA14 0x0bc 0x3d0 0x8c0 0x3 0x0
+#define MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x0bc 0x3d0 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x0bc 0x3d0 0x928 0x4 0x0
+#define MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x0bc 0x3d0 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D26__IPU1_SISG2 0x0bc 0x3d0 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D26__IPU1_DISP1_DATA22 0x0bc 0x3d0 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D27__EIM_DATA27 0x0c0 0x3d4 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D27__IPU1_DI1_PIN13 0x0c0 0x3d4 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D27__IPU1_CSI0_DATA00 0x0c0 0x3d4 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D27__IPU2_CSI1_DATA13 0x0c0 0x3d4 0x8bc 0x3 0x0
+#define MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x0c0 0x3d4 0x928 0x4 0x1
+#define MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x0c0 0x3d4 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x0c0 0x3d4 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D27__IPU1_SISG3 0x0c0 0x3d4 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D27__IPU1_DISP1_DATA23 0x0c0 0x3d4 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D28__EIM_DATA28 0x0c4 0x3d8 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D28__I2C1_SDA 0x0c4 0x3d8 0x89c 0x1 0x0
+#define MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x0c4 0x3d8 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D28__IPU2_CSI1_DATA12 0x0c4 0x3d8 0x8b8 0x3 0x0
+#define MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x0c4 0x3d8 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D28__UART2_RTS_B 0x0c4 0x3d8 0x924 0x4 0x0
+#define MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x0c4 0x3d8 0x924 0x4 0x0
+#define MX6QDL_PAD_EIM_D28__UART2_DTE_RTS_B 0x0c4 0x3d8 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x0c4 0x3d8 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D28__IPU1_EXT_TRIG 0x0c4 0x3d8 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_D28__IPU1_DI0_PIN13 0x0c4 0x3d8 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D29__EIM_DATA29 0x0c8 0x3dc 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D29__IPU1_DI1_PIN15 0x0c8 0x3dc 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D29__ECSPI4_SS0 0x0c8 0x3dc 0x824 0x2 0x1
+#define MX6QDL_PAD_EIM_D29__UART2_RTS_B 0x0c8 0x3dc 0x924 0x4 0x1
+#define MX6QDL_PAD_EIM_D29__UART2_CTS_B 0x0c8 0x3dc 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x0c8 0x3dc 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D29__UART2_DTE_CTS_B 0x0c8 0x3dc 0x924 0x4 0x1
+#define MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x0c8 0x3dc 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D29__IPU2_CSI1_VSYNC 0x0c8 0x3dc 0x8e4 0x6 0x0
+#define MX6QDL_PAD_EIM_D29__IPU1_DI0_PIN14 0x0c8 0x3dc 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_D30__EIM_DATA30 0x0cc 0x3e0 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D30__IPU1_DISP1_DATA21 0x0cc 0x3e0 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D30__IPU1_DI0_PIN11 0x0cc 0x3e0 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D30__IPU1_CSI0_DATA03 0x0cc 0x3e0 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_D30__UART3_CTS_B 0x0cc 0x3e0 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D30__UART3_RTS_B 0x0cc 0x3e0 0x92c 0x4 0x2
+#define MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x0cc 0x3e0 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D30__USB_H1_OC 0x0cc 0x3e0 0x948 0x6 0x0
+#define MX6QDL_PAD_EIM_D31__EIM_DATA31 0x0d0 0x3e4 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_D31__IPU1_DISP1_DATA20 0x0d0 0x3e4 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_D31__IPU1_DI0_PIN12 0x0d0 0x3e4 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_D31__IPU1_CSI0_DATA02 0x0d0 0x3e4 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x0d0 0x3e4 0x92c 0x4 0x3
+#define MX6QDL_PAD_EIM_D31__UART3_CTS_B 0x0d0 0x3e4 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x0d0 0x3e4 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_D31__USB_H1_PWR 0x0d0 0x3e4 0x000 0x6 0x0
+#define MX6QDL_PAD_EIM_A24__EIM_ADDR24 0x0d4 0x3e8 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A24__IPU1_DISP1_DATA19 0x0d4 0x3e8 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A24__IPU2_CSI1_DATA19 0x0d4 0x3e8 0x8d4 0x2 0x1
+#define MX6QDL_PAD_EIM_A24__IPU2_SISG2 0x0d4 0x3e8 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_A24__IPU1_SISG2 0x0d4 0x3e8 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x0d4 0x3e8 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A24__SRC_BOOT_CFG24 0x0d4 0x3e8 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A23__EIM_ADDR23 0x0d8 0x3ec 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A23__IPU1_DISP1_DATA18 0x0d8 0x3ec 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A23__IPU2_CSI1_DATA18 0x0d8 0x3ec 0x8d0 0x2 0x1
+#define MX6QDL_PAD_EIM_A23__IPU2_SISG3 0x0d8 0x3ec 0x000 0x3 0x0
+#define MX6QDL_PAD_EIM_A23__IPU1_SISG3 0x0d8 0x3ec 0x000 0x4 0x0
+#define MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x0d8 0x3ec 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A23__SRC_BOOT_CFG23 0x0d8 0x3ec 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A22__EIM_ADDR22 0x0dc 0x3f0 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A22__IPU1_DISP1_DATA17 0x0dc 0x3f0 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A22__IPU2_CSI1_DATA17 0x0dc 0x3f0 0x8cc 0x2 0x1
+#define MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x0dc 0x3f0 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A22__SRC_BOOT_CFG22 0x0dc 0x3f0 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A21__EIM_ADDR21 0x0e0 0x3f4 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A21__IPU1_DISP1_DATA16 0x0e0 0x3f4 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A21__IPU2_CSI1_DATA16 0x0e0 0x3f4 0x8c8 0x2 0x1
+#define MX6QDL_PAD_EIM_A21__GPIO2_IO17 0x0e0 0x3f4 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A21__SRC_BOOT_CFG21 0x0e0 0x3f4 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A20__EIM_ADDR20 0x0e4 0x3f8 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A20__IPU1_DISP1_DATA15 0x0e4 0x3f8 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A20__IPU2_CSI1_DATA15 0x0e4 0x3f8 0x8c4 0x2 0x1
+#define MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x0e4 0x3f8 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A20__SRC_BOOT_CFG20 0x0e4 0x3f8 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A19__EIM_ADDR19 0x0e8 0x3fc 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A19__IPU1_DISP1_DATA14 0x0e8 0x3fc 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A19__IPU2_CSI1_DATA14 0x0e8 0x3fc 0x8c0 0x2 0x1
+#define MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x0e8 0x3fc 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A19__SRC_BOOT_CFG19 0x0e8 0x3fc 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A18__EIM_ADDR18 0x0ec 0x400 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A18__IPU1_DISP1_DATA13 0x0ec 0x400 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A18__IPU2_CSI1_DATA13 0x0ec 0x400 0x8bc 0x2 0x1
+#define MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x0ec 0x400 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A18__SRC_BOOT_CFG18 0x0ec 0x400 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A17__EIM_ADDR17 0x0f0 0x404 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A17__IPU1_DISP1_DATA12 0x0f0 0x404 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A17__IPU2_CSI1_DATA12 0x0f0 0x404 0x8b8 0x2 0x1
+#define MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x0f0 0x404 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A17__SRC_BOOT_CFG17 0x0f0 0x404 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_A16__EIM_ADDR16 0x0f4 0x408 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_A16__IPU1_DI1_DISP_CLK 0x0f4 0x408 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_A16__IPU2_CSI1_PIXCLK 0x0f4 0x408 0x8e0 0x2 0x1
+#define MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x0f4 0x408 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_A16__SRC_BOOT_CFG16 0x0f4 0x408 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0x0f8 0x40c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_CS0__IPU1_DI1_PIN05 0x0f8 0x40c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x0f8 0x40c 0x810 0x2 0x0
+#define MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x0f8 0x40c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_CS1__EIM_CS1_B 0x0fc 0x410 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_CS1__IPU1_DI1_PIN06 0x0fc 0x410 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x0fc 0x410 0x818 0x2 0x0
+#define MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x0fc 0x410 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_OE__EIM_OE_B 0x100 0x414 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_OE__IPU1_DI1_PIN07 0x100 0x414 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100 0x414 0x814 0x2 0x0
+#define MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x100 0x414 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_RW__EIM_RW 0x104 0x418 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_RW__IPU1_DI1_PIN08 0x104 0x418 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_RW__ECSPI2_SS0 0x104 0x418 0x81c 0x2 0x0
+#define MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x104 0x418 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_RW__SRC_BOOT_CFG29 0x104 0x418 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_LBA__EIM_LBA_B 0x108 0x41c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_LBA__IPU1_DI1_PIN17 0x108 0x41c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_LBA__ECSPI2_SS1 0x108 0x41c 0x820 0x2 0x0
+#define MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x108 0x41c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_LBA__SRC_BOOT_CFG26 0x108 0x41c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_EB0__EIM_EB0_B 0x10c 0x420 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_EB0__IPU1_DISP1_DATA11 0x10c 0x420 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_EB0__IPU2_CSI1_DATA11 0x10c 0x420 0x8b4 0x2 0x1
+#define MX6QDL_PAD_EIM_EB0__CCM_PMIC_READY 0x10c 0x420 0x7f0 0x4 0x0
+#define MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x10c 0x420 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_EB0__SRC_BOOT_CFG27 0x10c 0x420 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_EB1__EIM_EB1_B 0x110 0x424 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_EB1__IPU1_DISP1_DATA10 0x110 0x424 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_EB1__IPU2_CSI1_DATA10 0x110 0x424 0x8b0 0x2 0x1
+#define MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x110 0x424 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_EB1__SRC_BOOT_CFG28 0x110 0x424 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA0__EIM_AD00 0x114 0x428 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA0__IPU1_DISP1_DATA09 0x114 0x428 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA0__IPU2_CSI1_DATA09 0x114 0x428 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x114 0x428 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA0__SRC_BOOT_CFG00 0x114 0x428 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA1__EIM_AD01 0x118 0x42c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA1__IPU1_DISP1_DATA08 0x118 0x42c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA1__IPU2_CSI1_DATA08 0x118 0x42c 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x118 0x42c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA1__SRC_BOOT_CFG01 0x118 0x42c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA2__EIM_AD02 0x11c 0x430 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA2__IPU1_DISP1_DATA07 0x11c 0x430 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA2__IPU2_CSI1_DATA07 0x11c 0x430 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x11c 0x430 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA2__SRC_BOOT_CFG02 0x11c 0x430 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA3__EIM_AD03 0x120 0x434 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA3__IPU1_DISP1_DATA06 0x120 0x434 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA3__IPU2_CSI1_DATA06 0x120 0x434 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x120 0x434 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA3__SRC_BOOT_CFG03 0x120 0x434 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA4__EIM_AD04 0x124 0x438 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA4__IPU1_DISP1_DATA05 0x124 0x438 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA4__IPU2_CSI1_DATA05 0x124 0x438 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x124 0x438 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA4__SRC_BOOT_CFG04 0x124 0x438 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA5__EIM_AD05 0x128 0x43c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA5__IPU1_DISP1_DATA04 0x128 0x43c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA5__IPU2_CSI1_DATA04 0x128 0x43c 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x128 0x43c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA5__SRC_BOOT_CFG05 0x128 0x43c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA6__EIM_AD06 0x12c 0x440 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA6__IPU1_DISP1_DATA03 0x12c 0x440 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA6__IPU2_CSI1_DATA03 0x12c 0x440 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x12c 0x440 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA6__SRC_BOOT_CFG06 0x12c 0x440 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA7__EIM_AD07 0x130 0x444 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA7__IPU1_DISP1_DATA02 0x130 0x444 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA7__IPU2_CSI1_DATA02 0x130 0x444 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x130 0x444 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA7__SRC_BOOT_CFG07 0x130 0x444 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA8__EIM_AD08 0x134 0x448 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA8__IPU1_DISP1_DATA01 0x134 0x448 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA8__IPU2_CSI1_DATA01 0x134 0x448 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x134 0x448 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA8__SRC_BOOT_CFG08 0x134 0x448 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA9__EIM_AD09 0x138 0x44c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA9__IPU1_DISP1_DATA00 0x138 0x44c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA9__IPU2_CSI1_DATA00 0x138 0x44c 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x138 0x44c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA9__SRC_BOOT_CFG09 0x138 0x44c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA10__EIM_AD10 0x13c 0x450 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA10__IPU1_DI1_PIN15 0x13c 0x450 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA10__IPU2_CSI1_DATA_EN 0x13c 0x450 0x8d8 0x2 0x1
+#define MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x13c 0x450 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA10__SRC_BOOT_CFG10 0x13c 0x450 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA11__EIM_AD11 0x140 0x454 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA11__IPU1_DI1_PIN02 0x140 0x454 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA11__IPU2_CSI1_HSYNC 0x140 0x454 0x8dc 0x2 0x1
+#define MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x140 0x454 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA11__SRC_BOOT_CFG11 0x140 0x454 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA12__EIM_AD12 0x144 0x458 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA12__IPU1_DI1_PIN03 0x144 0x458 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA12__IPU2_CSI1_VSYNC 0x144 0x458 0x8e4 0x2 0x1
+#define MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x144 0x458 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA12__SRC_BOOT_CFG12 0x144 0x458 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA13__EIM_AD13 0x148 0x45c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA13__IPU1_DI1_D0_CS 0x148 0x45c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x148 0x45c 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA13__SRC_BOOT_CFG13 0x148 0x45c 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA14__EIM_AD14 0x14c 0x460 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA14__IPU1_DI1_D1_CS 0x14c 0x460 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x14c 0x460 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA14__SRC_BOOT_CFG14 0x14c 0x460 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_DA15__EIM_AD15 0x150 0x464 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_DA15__IPU1_DI1_PIN01 0x150 0x464 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_DA15__IPU1_DI1_PIN04 0x150 0x464 0x000 0x2 0x0
+#define MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x150 0x464 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_DA15__SRC_BOOT_CFG15 0x150 0x464 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0x154 0x468 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_WAIT__EIM_DTACK_B 0x154 0x468 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x154 0x468 0x000 0x5 0x0
+#define MX6QDL_PAD_EIM_WAIT__SRC_BOOT_CFG25 0x154 0x468 0x000 0x7 0x0
+#define MX6QDL_PAD_EIM_BCLK__EIM_BCLK 0x158 0x46c 0x000 0x0 0x0
+#define MX6QDL_PAD_EIM_BCLK__IPU1_DI1_PIN16 0x158 0x46c 0x000 0x1 0x0
+#define MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x158 0x46c 0x000 0x5 0x0
+#define MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x15c 0x470 0x000 0x0 0x0
+#define MX6QDL_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK 0x15c 0x470 0x000 0x1 0x0
+#define MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x15c 0x470 0x000 0x5 0x0
+#define MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x160 0x474 0x000 0x0 0x0
+#define MX6QDL_PAD_DI0_PIN15__IPU2_DI0_PIN15 0x160 0x474 0x000 0x1 0x0
+#define MX6QDL_PAD_DI0_PIN15__AUD6_TXC 0x160 0x474 0x000 0x2 0x0
+#define MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x160 0x474 0x000 0x5 0x0
+#define MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x164 0x478 0x000 0x0 0x0
+#define MX6QDL_PAD_DI0_PIN2__IPU2_DI0_PIN02 0x164 0x478 0x000 0x1 0x0
+#define MX6QDL_PAD_DI0_PIN2__AUD6_TXD 0x164 0x478 0x000 0x2 0x0
+#define MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x164 0x478 0x000 0x5 0x0
+#define MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x168 0x47c 0x000 0x0 0x0
+#define MX6QDL_PAD_DI0_PIN3__IPU2_DI0_PIN03 0x168 0x47c 0x000 0x1 0x0
+#define MX6QDL_PAD_DI0_PIN3__AUD6_TXFS 0x168 0x47c 0x000 0x2 0x0
+#define MX6QDL_PAD_DI0_PIN3__GPIO4_IO19 0x168 0x47c 0x000 0x5 0x0
+#define MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04 0x16c 0x480 0x000 0x0 0x0
+#define MX6QDL_PAD_DI0_PIN4__IPU2_DI0_PIN04 0x16c 0x480 0x000 0x1 0x0
+#define MX6QDL_PAD_DI0_PIN4__AUD6_RXD 0x16c 0x480 0x000 0x2 0x0
+#define MX6QDL_PAD_DI0_PIN4__SD1_WP 0x16c 0x480 0x94c 0x3 0x0
+#define MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x16c 0x480 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x170 0x484 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT0__IPU2_DISP0_DATA00 0x170 0x484 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x170 0x484 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x170 0x484 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x174 0x488 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT1__IPU2_DISP0_DATA01 0x174 0x488 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x174 0x488 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x174 0x488 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x178 0x48c 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT2__IPU2_DISP0_DATA02 0x178 0x48c 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x178 0x48c 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x178 0x48c 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x17c 0x490 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT3__IPU2_DISP0_DATA03 0x17c 0x490 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT3__ECSPI3_SS0 0x17c 0x490 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x17c 0x490 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x180 0x494 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT4__IPU2_DISP0_DATA04 0x180 0x494 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT4__ECSPI3_SS1 0x180 0x494 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x180 0x494 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x184 0x498 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT5__IPU2_DISP0_DATA05 0x184 0x498 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT5__ECSPI3_SS2 0x184 0x498 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT5__AUD6_RXFS 0x184 0x498 0x000 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x184 0x498 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x188 0x49c 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT6__IPU2_DISP0_DATA06 0x188 0x49c 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT6__ECSPI3_SS3 0x188 0x49c 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT6__AUD6_RXC 0x188 0x49c 0x000 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x188 0x49c 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x18c 0x4a0 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT7__IPU2_DISP0_DATA07 0x18c 0x4a0 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT7__ECSPI3_RDY 0x18c 0x4a0 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x18c 0x4a0 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x190 0x4a4 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT8__IPU2_DISP0_DATA08 0x190 0x4a4 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x190 0x4a4 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x190 0x4a4 0x000 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT8__GPIO4_IO29 0x190 0x4a4 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x194 0x4a8 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT9__IPU2_DISP0_DATA09 0x194 0x4a8 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x194 0x4a8 0x000 0x2 0x0
+#define MX6QDL_PAD_DISP0_DAT9__WDOG2_B 0x194 0x4a8 0x000 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x194 0x4a8 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x198 0x4ac 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT10__IPU2_DISP0_DATA10 0x198 0x4ac 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31 0x198 0x4ac 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x19c 0x4b0 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT11__IPU2_DISP0_DATA11 0x19c 0x4b0 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x19c 0x4b0 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x1a0 0x4b4 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT12__IPU2_DISP0_DATA12 0x1a0 0x4b4 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT12__GPIO5_IO06 0x1a0 0x4b4 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x1a4 0x4b8 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT13__IPU2_DISP0_DATA13 0x1a4 0x4b8 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT13__AUD5_RXFS 0x1a4 0x4b8 0x7d8 0x3 0x1
+#define MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07 0x1a4 0x4b8 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x1a8 0x4bc 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT14__IPU2_DISP0_DATA14 0x1a8 0x4bc 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT14__AUD5_RXC 0x1a8 0x4bc 0x7d4 0x3 0x1
+#define MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1a8 0x4bc 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x1ac 0x4c0 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT15__IPU2_DISP0_DATA15 0x1ac 0x4c0 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT15__ECSPI1_SS1 0x1ac 0x4c0 0x804 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT15__ECSPI2_SS1 0x1ac 0x4c0 0x820 0x3 0x1
+#define MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1ac 0x4c0 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x1b0 0x4c4 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT16__IPU2_DISP0_DATA16 0x1b0 0x4c4 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x1b0 0x4c4 0x818 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT16__AUD5_TXC 0x1b0 0x4c4 0x7dc 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT16__SDMA_EXT_EVENT0 0x1b0 0x4c4 0x90c 0x4 0x0
+#define MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x1b0 0x4c4 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x1b4 0x4c8 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT17__IPU2_DISP0_DATA17 0x1b4 0x4c8 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO 0x1b4 0x4c8 0x814 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT17__AUD5_TXD 0x1b4 0x4c8 0x7d0 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT17__SDMA_EXT_EVENT1 0x1b4 0x4c8 0x910 0x4 0x0
+#define MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x1b4 0x4c8 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x1b8 0x4cc 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT18__IPU2_DISP0_DATA18 0x1b8 0x4cc 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT18__ECSPI2_SS0 0x1b8 0x4cc 0x81c 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS 0x1b8 0x4cc 0x7e0 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT18__AUD4_RXFS 0x1b8 0x4cc 0x7c0 0x4 0x0
+#define MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x1b8 0x4cc 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT18__EIM_CS2_B 0x1b8 0x4cc 0x000 0x7 0x0
+#define MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x1bc 0x4d0 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT19__IPU2_DISP0_DATA19 0x1bc 0x4d0 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK 0x1bc 0x4d0 0x810 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x1bc 0x4d0 0x7cc 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT19__AUD4_RXC 0x1bc 0x4d0 0x7bc 0x4 0x0
+#define MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1bc 0x4d0 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT19__EIM_CS3_B 0x1bc 0x4d0 0x000 0x7 0x0
+#define MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x1c0 0x4d4 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT20__IPU2_DISP0_DATA20 0x1c0 0x4d4 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT20__ECSPI1_SCLK 0x1c0 0x4d4 0x7f4 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x1c0 0x4d4 0x7c4 0x3 0x0
+#define MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x1c0 0x4d4 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x1c4 0x4d8 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT21__IPU2_DISP0_DATA21 0x1c4 0x4d8 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT21__ECSPI1_MOSI 0x1c4 0x4d8 0x7fc 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x1c4 0x4d8 0x7b8 0x3 0x1
+#define MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1c4 0x4d8 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x1c8 0x4dc 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT22__IPU2_DISP0_DATA22 0x1c8 0x4dc 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT22__ECSPI1_MISO 0x1c8 0x4dc 0x7f8 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x1c8 0x4dc 0x7c8 0x3 0x1
+#define MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16 0x1c8 0x4dc 0x000 0x5 0x0
+#define MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x1cc 0x4e0 0x000 0x0 0x0
+#define MX6QDL_PAD_DISP0_DAT23__IPU2_DISP0_DATA23 0x1cc 0x4e0 0x000 0x1 0x0
+#define MX6QDL_PAD_DISP0_DAT23__ECSPI1_SS0 0x1cc 0x4e0 0x800 0x2 0x1
+#define MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x1cc 0x4e0 0x7b4 0x3 0x1
+#define MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1cc 0x4e0 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1d0 0x4e4 0x840 0x1 0x0
+#define MX6QDL_PAD_ENET_MDIO__ESAI_RX_CLK 0x1d0 0x4e4 0x86c 0x2 0x0
+#define MX6QDL_PAD_ENET_MDIO__ENET_1588_EVENT1_OUT 0x1d0 0x4e4 0x000 0x4 0x0
+#define MX6QDL_PAD_ENET_MDIO__GPIO1_IO22 0x1d0 0x4e4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_MDIO__SPDIF_LOCK 0x1d0 0x4e4 0x000 0x6 0x0
+#define MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1d4 0x4e8 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_REF_CLK__ESAI_RX_FS 0x1d4 0x4e8 0x85c 0x2 0x0
+#define MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1d4 0x4e8 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_REF_CLK__SPDIF_SR_CLK 0x1d4 0x4e8 0x000 0x6 0x0
+#define MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1d8 0x4ec 0x004 0x0 0xff0d0100
+#define MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1d8 0x4ec 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_RX_ER__ESAI_RX_HF_CLK 0x1d8 0x4ec 0x864 0x2 0x0
+#define MX6QDL_PAD_ENET_RX_ER__SPDIF_IN 0x1d8 0x4ec 0x914 0x3 0x1
+#define MX6QDL_PAD_ENET_RX_ER__ENET_1588_EVENT2_OUT 0x1d8 0x4ec 0x000 0x4 0x0
+#define MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x1d8 0x4ec 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1dc 0x4f0 0x858 0x1 0x1
+#define MX6QDL_PAD_ENET_CRS_DV__ESAI_TX_CLK 0x1dc 0x4f0 0x870 0x2 0x0
+#define MX6QDL_PAD_ENET_CRS_DV__SPDIF_EXT_CLK 0x1dc 0x4f0 0x918 0x3 0x1
+#define MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1dc 0x4f0 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_RXD1__MLB_SIG 0x1e0 0x4f4 0x908 0x0 0x0
+#define MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1e0 0x4f4 0x84c 0x1 0x1
+#define MX6QDL_PAD_ENET_RXD1__ESAI_TX_FS 0x1e0 0x4f4 0x860 0x2 0x0
+#define MX6QDL_PAD_ENET_RXD1__ENET_1588_EVENT3_OUT 0x1e0 0x4f4 0x000 0x4 0x0
+#define MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1e0 0x4f4 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1e4 0x4f8 0x848 0x1 0x1
+#define MX6QDL_PAD_ENET_RXD0__ESAI_TX_HF_CLK 0x1e4 0x4f8 0x868 0x2 0x0
+#define MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1e4 0x4f8 0x000 0x3 0x0
+#define MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1e4 0x4f8 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1e8 0x4fc 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_TX_EN__ESAI_TX3_RX2 0x1e8 0x4fc 0x880 0x2 0x0
+#define MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1e8 0x4fc 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_TXD1__MLB_CLK 0x1ec 0x500 0x900 0x0 0x0
+#define MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1ec 0x500 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_TXD1__ESAI_TX2_RX3 0x1ec 0x500 0x87c 0x2 0x0
+#define MX6QDL_PAD_ENET_TXD1__ENET_1588_EVENT0_IN 0x1ec 0x500 0x000 0x4 0x0
+#define MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1ec 0x500 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1f0 0x504 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_TXD0__ESAI_TX4_RX1 0x1f0 0x504 0x884 0x2 0x0
+#define MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x1f0 0x504 0x000 0x5 0x0
+#define MX6QDL_PAD_ENET_MDC__MLB_DATA 0x1f4 0x508 0x904 0x0 0x0
+#define MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1f4 0x508 0x000 0x1 0x0
+#define MX6QDL_PAD_ENET_MDC__ESAI_TX5_RX0 0x1f4 0x508 0x888 0x2 0x0
+#define MX6QDL_PAD_ENET_MDC__ENET_1588_EVENT1_IN 0x1f4 0x508 0x000 0x4 0x0
+#define MX6QDL_PAD_ENET_MDC__GPIO1_IO31 0x1f4 0x508 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x1f8 0x5c8 0x7f4 0x0 0x2
+#define MX6QDL_PAD_KEY_COL0__ENET_RX_DATA3 0x1f8 0x5c8 0x854 0x1 0x1
+#define MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x1f8 0x5c8 0x7dc 0x2 0x1
+#define MX6QDL_PAD_KEY_COL0__KEY_COL0 0x1f8 0x5c8 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1f8 0x5c8 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_COL0__UART4_RX_DATA 0x1f8 0x5c8 0x938 0x4 0x0
+#define MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1f8 0x5c8 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_COL0__DCIC1_OUT 0x1f8 0x5c8 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x1fc 0x5cc 0x7fc 0x0 0x2
+#define MX6QDL_PAD_KEY_ROW0__ENET_TX_DATA3 0x1fc 0x5cc 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x1fc 0x5cc 0x7d0 0x2 0x1
+#define MX6QDL_PAD_KEY_ROW0__KEY_ROW0 0x1fc 0x5cc 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1fc 0x5cc 0x938 0x4 0x1
+#define MX6QDL_PAD_KEY_ROW0__UART4_TX_DATA 0x1fc 0x5cc 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1fc 0x5cc 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_ROW0__DCIC2_OUT 0x1fc 0x5cc 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x200 0x5d0 0x7f8 0x0 0x2
+#define MX6QDL_PAD_KEY_COL1__ENET_MDIO 0x200 0x5d0 0x840 0x1 0x1
+#define MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x200 0x5d0 0x7e0 0x2 0x1
+#define MX6QDL_PAD_KEY_COL1__KEY_COL1 0x200 0x5d0 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x200 0x5d0 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_COL1__UART5_RX_DATA 0x200 0x5d0 0x940 0x4 0x0
+#define MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x200 0x5d0 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_COL1__SD1_VSELECT 0x200 0x5d0 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_ROW1__ECSPI1_SS0 0x204 0x5d4 0x800 0x0 0x2
+#define MX6QDL_PAD_KEY_ROW1__ENET_COL 0x204 0x5d4 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_ROW1__AUD5_RXD 0x204 0x5d4 0x7cc 0x2 0x1
+#define MX6QDL_PAD_KEY_ROW1__KEY_ROW1 0x204 0x5d4 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x204 0x5d4 0x940 0x4 0x1
+#define MX6QDL_PAD_KEY_ROW1__UART5_TX_DATA 0x204 0x5d4 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x204 0x5d4 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_ROW1__SD2_VSELECT 0x204 0x5d4 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_COL2__ECSPI1_SS1 0x208 0x5d8 0x804 0x0 0x2
+#define MX6QDL_PAD_KEY_COL2__ENET_RX_DATA2 0x208 0x5d8 0x850 0x1 0x1
+#define MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x208 0x5d8 0x000 0x2 0x0
+#define MX6QDL_PAD_KEY_COL2__KEY_COL2 0x208 0x5d8 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_COL2__ENET_MDC 0x208 0x5d8 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x208 0x5d8 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_COL2__USB_H1_PWR_CTL_WAKE 0x208 0x5d8 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_ROW2__ECSPI1_SS2 0x20c 0x5dc 0x808 0x0 0x1
+#define MX6QDL_PAD_KEY_ROW2__ENET_TX_DATA2 0x20c 0x5dc 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x20c 0x5dc 0x7e4 0x2 0x0
+#define MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x20c 0x5dc 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_ROW2__SD2_VSELECT 0x20c 0x5dc 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x20c 0x5dc 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x20c 0x5dc 0x88c 0x6 0x1
+#define MX6QDL_PAD_KEY_COL3__ECSPI1_SS3 0x210 0x5e0 0x80c 0x0 0x1
+#define MX6QDL_PAD_KEY_COL3__ENET_CRS 0x210 0x5e0 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_COL3__HDMI_TX_DDC_SCL 0x210 0x5e0 0x890 0x2 0x1
+#define MX6QDL_PAD_KEY_COL3__KEY_COL3 0x210 0x5e0 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x210 0x5e0 0x8a0 0x4 0x1
+#define MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x210 0x5e0 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_COL3__SPDIF_IN 0x210 0x5e0 0x914 0x6 0x2
+#define MX6QDL_PAD_KEY_ROW3__ASRC_EXT_CLK 0x214 0x5e4 0x7b0 0x1 0x0
+#define MX6QDL_PAD_KEY_ROW3__HDMI_TX_DDC_SDA 0x214 0x5e4 0x894 0x2 0x1
+#define MX6QDL_PAD_KEY_ROW3__KEY_ROW3 0x214 0x5e4 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x214 0x5e4 0x8a4 0x4 0x1
+#define MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x214 0x5e4 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_ROW3__SD1_VSELECT 0x214 0x5e4 0x000 0x6 0x0
+#define MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x218 0x5e8 0x000 0x0 0x0
+#define MX6QDL_PAD_KEY_COL4__IPU1_SISG4 0x218 0x5e8 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x218 0x5e8 0x944 0x2 0x1
+#define MX6QDL_PAD_KEY_COL4__KEY_COL4 0x218 0x5e8 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_COL4__UART5_RTS_B 0x218 0x5e8 0x93c 0x4 0x0
+#define MX6QDL_PAD_KEY_COL4__UART5_CTS_B 0x218 0x5e8 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x218 0x5e8 0x000 0x5 0x0
+#define MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x21c 0x5ec 0x7e8 0x0 0x0
+#define MX6QDL_PAD_KEY_ROW4__IPU1_SISG5 0x21c 0x5ec 0x000 0x1 0x0
+#define MX6QDL_PAD_KEY_ROW4__USB_OTG_PWR 0x21c 0x5ec 0x000 0x2 0x0
+#define MX6QDL_PAD_KEY_ROW4__KEY_ROW4 0x21c 0x5ec 0x000 0x3 0x0
+#define MX6QDL_PAD_KEY_ROW4__UART5_CTS_B 0x21c 0x5ec 0x000 0x4 0x0
+#define MX6QDL_PAD_KEY_ROW4__UART5_RTS_B 0x21c 0x5ec 0x93c 0x4 0x1
+#define MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x21c 0x5ec 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x220 0x5f0 0x000 0x0 0x0
+#define MX6QDL_PAD_GPIO_0__KEY_COL5 0x220 0x5f0 0x8e8 0x2 0x0
+#define MX6QDL_PAD_GPIO_0__ASRC_EXT_CLK 0x220 0x5f0 0x7b0 0x3 0x1
+#define MX6QDL_PAD_GPIO_0__EPIT1_OUT 0x220 0x5f0 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x220 0x5f0 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_0__USB_H1_PWR 0x220 0x5f0 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_0__SNVS_VIO_5 0x220 0x5f0 0x000 0x7 0x0
+#define MX6QDL_PAD_GPIO_1__ESAI_RX_CLK 0x224 0x5f4 0x86c 0x0 0x1
+#define MX6QDL_PAD_GPIO_1__WDOG2_B 0x224 0x5f4 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_1__KEY_ROW5 0x224 0x5f4 0x8f4 0x2 0x0
+#define MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x224 0x5f4 0x004 0x3 0xff0d0101
+#define MX6QDL_PAD_GPIO_1__PWM2_OUT 0x224 0x5f4 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x224 0x5f4 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_1__SD1_CD_B 0x224 0x5f4 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_9__ESAI_RX_FS 0x228 0x5f8 0x85c 0x0 0x1
+#define MX6QDL_PAD_GPIO_9__WDOG1_B 0x228 0x5f8 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_9__KEY_COL6 0x228 0x5f8 0x8ec 0x2 0x0
+#define MX6QDL_PAD_GPIO_9__CCM_REF_EN_B 0x228 0x5f8 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_9__PWM1_OUT 0x228 0x5f8 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x228 0x5f8 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_9__SD1_WP 0x228 0x5f8 0x94c 0x6 0x1
+#define MX6QDL_PAD_GPIO_3__ESAI_RX_HF_CLK 0x22c 0x5fc 0x864 0x0 0x1
+#define MX6QDL_PAD_GPIO_3__I2C3_SCL 0x22c 0x5fc 0x8a8 0x2 0x1
+#define MX6QDL_PAD_GPIO_3__XTALOSC_REF_CLK_24M 0x22c 0x5fc 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_3__CCM_CLKO2 0x22c 0x5fc 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x22c 0x5fc 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_3__USB_H1_OC 0x22c 0x5fc 0x948 0x6 0x1
+#define MX6QDL_PAD_GPIO_3__MLB_CLK 0x22c 0x5fc 0x900 0x7 0x1
+#define MX6QDL_PAD_GPIO_6__ESAI_TX_CLK 0x230 0x600 0x870 0x0 0x1
+#define MX6QDL_PAD_GPIO_6__ENET_IRQ 0x230 0x600 0x03c 0x11 0xff000609
+#define MX6QDL_PAD_GPIO_6__I2C3_SDA 0x230 0x600 0x8ac 0x2 0x1
+#define MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x230 0x600 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_6__SD2_LCTL 0x230 0x600 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_6__MLB_SIG 0x230 0x600 0x908 0x7 0x1
+#define MX6QDL_PAD_GPIO_2__ESAI_TX_FS 0x234 0x604 0x860 0x0 0x1
+#define MX6QDL_PAD_GPIO_2__KEY_ROW6 0x234 0x604 0x8f8 0x2 0x1
+#define MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x234 0x604 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_2__SD2_WP 0x234 0x604 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_2__MLB_DATA 0x234 0x604 0x904 0x7 0x1
+#define MX6QDL_PAD_GPIO_4__ESAI_TX_HF_CLK 0x238 0x608 0x868 0x0 0x1
+#define MX6QDL_PAD_GPIO_4__KEY_COL7 0x238 0x608 0x8f0 0x2 0x1
+#define MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x238 0x608 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_4__SD2_CD_B 0x238 0x608 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_5__ESAI_TX2_RX3 0x23c 0x60c 0x87c 0x0 0x1
+#define MX6QDL_PAD_GPIO_5__KEY_ROW7 0x23c 0x60c 0x8fc 0x2 0x1
+#define MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x23c 0x60c 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x23c 0x60c 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_5__I2C3_SCL 0x23c 0x60c 0x8a8 0x6 0x2
+#define MX6QDL_PAD_GPIO_5__ARM_EVENTI 0x23c 0x60c 0x000 0x7 0x0
+#define MX6QDL_PAD_GPIO_7__ESAI_TX4_RX1 0x240 0x610 0x884 0x0 0x1
+#define MX6QDL_PAD_GPIO_7__ECSPI5_RDY 0x240 0x610 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_7__EPIT1_OUT 0x240 0x610 0x000 0x2 0x0
+#define MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x240 0x610 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_7__UART2_TX_DATA 0x240 0x610 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_7__UART2_RX_DATA 0x240 0x610 0x928 0x4 0x2
+#define MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x240 0x610 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_7__SPDIF_LOCK 0x240 0x610 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_7__USB_OTG_HOST_MODE 0x240 0x610 0x000 0x7 0x0
+#define MX6QDL_PAD_GPIO_8__ESAI_TX5_RX0 0x244 0x614 0x888 0x0 0x1
+#define MX6QDL_PAD_GPIO_8__XTALOSC_REF_CLK_32K 0x244 0x614 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_8__EPIT2_OUT 0x244 0x614 0x000 0x2 0x0
+#define MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x244 0x614 0x7e4 0x3 0x1
+#define MX6QDL_PAD_GPIO_8__UART2_RX_DATA 0x244 0x614 0x928 0x4 0x3
+#define MX6QDL_PAD_GPIO_8__UART2_TX_DATA 0x244 0x614 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x244 0x614 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_8__SPDIF_SR_CLK 0x244 0x614 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_8__USB_OTG_PWR_CTL_WAKE 0x244 0x614 0x000 0x7 0x0
+#define MX6QDL_PAD_GPIO_16__ESAI_TX3_RX2 0x248 0x618 0x880 0x0 0x1
+#define MX6QDL_PAD_GPIO_16__ENET_1588_EVENT2_IN 0x248 0x618 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x248 0x618 0x83c 0x2 0x1
+#define MX6QDL_PAD_GPIO_16__SD1_LCTL 0x248 0x618 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_16__SPDIF_IN 0x248 0x618 0x914 0x4 0x3
+#define MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x248 0x618 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_16__I2C3_SDA 0x248 0x618 0x8ac 0x6 0x2
+#define MX6QDL_PAD_GPIO_16__JTAG_DE_B 0x248 0x618 0x000 0x7 0x0
+#define MX6QDL_PAD_GPIO_17__ESAI_TX0 0x24c 0x61c 0x874 0x0 0x0
+#define MX6QDL_PAD_GPIO_17__ENET_1588_EVENT3_IN 0x24c 0x61c 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_17__CCM_PMIC_READY 0x24c 0x61c 0x7f0 0x2 0x1
+#define MX6QDL_PAD_GPIO_17__SDMA_EXT_EVENT0 0x24c 0x61c 0x90c 0x3 0x1
+#define MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x24c 0x61c 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x24c 0x61c 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_18__ESAI_TX1 0x250 0x620 0x878 0x0 0x0
+#define MX6QDL_PAD_GPIO_18__ENET_RX_CLK 0x250 0x620 0x844 0x1 0x1
+#define MX6QDL_PAD_GPIO_18__SD3_VSELECT 0x250 0x620 0x000 0x2 0x0
+#define MX6QDL_PAD_GPIO_18__SDMA_EXT_EVENT1 0x250 0x620 0x910 0x3 0x1
+#define MX6QDL_PAD_GPIO_18__ASRC_EXT_CLK 0x250 0x620 0x7b0 0x4 0x2
+#define MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x250 0x620 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_18__SNVS_VIO_5_CTL 0x250 0x620 0x000 0x6 0x0
+#define MX6QDL_PAD_GPIO_19__KEY_COL5 0x254 0x624 0x8e8 0x0 0x1
+#define MX6QDL_PAD_GPIO_19__ENET_1588_EVENT0_OUT 0x254 0x624 0x000 0x1 0x0
+#define MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x254 0x624 0x000 0x2 0x0
+#define MX6QDL_PAD_GPIO_19__CCM_CLKO1 0x254 0x624 0x000 0x3 0x0
+#define MX6QDL_PAD_GPIO_19__ECSPI1_RDY 0x254 0x624 0x000 0x4 0x0
+#define MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x254 0x624 0x000 0x5 0x0
+#define MX6QDL_PAD_GPIO_19__ENET_TX_ER 0x254 0x624 0x000 0x6 0x0
+#define MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x258 0x628 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x258 0x628 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_PIXCLK__ARM_EVENTO 0x258 0x628 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x25c 0x62c 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x25c 0x62c 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x25c 0x62c 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_MCLK__ARM_TRACE_CTL 0x25c 0x62c 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x260 0x630 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00 0x260 0x630 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x260 0x630 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DATA_EN__ARM_TRACE_CLK 0x260 0x630 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x264 0x634 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01 0x264 0x634 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x264 0x634 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_VSYNC__ARM_TRACE00 0x264 0x634 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04 0x268 0x638 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT4__EIM_DATA02 0x268 0x638 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT4__ECSPI1_SCLK 0x268 0x638 0x7f4 0x2 0x3
+#define MX6QDL_PAD_CSI0_DAT4__KEY_COL5 0x268 0x638 0x8e8 0x3 0x2
+#define MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x268 0x638 0x000 0x4 0x0
+#define MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x268 0x638 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT4__ARM_TRACE01 0x268 0x638 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05 0x26c 0x63c 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT5__EIM_DATA03 0x26c 0x63c 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT5__ECSPI1_MOSI 0x26c 0x63c 0x7fc 0x2 0x3
+#define MX6QDL_PAD_CSI0_DAT5__KEY_ROW5 0x26c 0x63c 0x8f4 0x3 0x1
+#define MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x26c 0x63c 0x000 0x4 0x0
+#define MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x26c 0x63c 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT5__ARM_TRACE02 0x26c 0x63c 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06 0x270 0x640 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT6__EIM_DATA04 0x270 0x640 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT6__ECSPI1_MISO 0x270 0x640 0x7f8 0x2 0x3
+#define MX6QDL_PAD_CSI0_DAT6__KEY_COL6 0x270 0x640 0x8ec 0x3 0x1
+#define MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x270 0x640 0x000 0x4 0x0
+#define MX6QDL_PAD_CSI0_DAT6__GPIO5_IO24 0x270 0x640 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT6__ARM_TRACE03 0x270 0x640 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07 0x274 0x644 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT7__EIM_DATA05 0x274 0x644 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT7__ECSPI1_SS0 0x274 0x644 0x800 0x2 0x3
+#define MX6QDL_PAD_CSI0_DAT7__KEY_ROW6 0x274 0x644 0x8f8 0x3 0x2
+#define MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x274 0x644 0x000 0x4 0x0
+#define MX6QDL_PAD_CSI0_DAT7__GPIO5_IO25 0x274 0x644 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT7__ARM_TRACE04 0x274 0x644 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08 0x278 0x648 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT8__EIM_DATA06 0x278 0x648 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK 0x278 0x648 0x810 0x2 0x2
+#define MX6QDL_PAD_CSI0_DAT8__KEY_COL7 0x278 0x648 0x8f0 0x3 0x2
+#define MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x278 0x648 0x89c 0x4 0x1
+#define MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x278 0x648 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT8__ARM_TRACE05 0x278 0x648 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09 0x27c 0x64c 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT9__EIM_DATA07 0x27c 0x64c 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI 0x27c 0x64c 0x818 0x2 0x2
+#define MX6QDL_PAD_CSI0_DAT9__KEY_ROW7 0x27c 0x64c 0x8fc 0x3 0x2
+#define MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x27c 0x64c 0x898 0x4 0x1
+#define MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x27c 0x64c 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT9__ARM_TRACE06 0x27c 0x64c 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10 0x280 0x650 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT10__AUD3_RXC 0x280 0x650 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO 0x280 0x650 0x814 0x2 0x2
+#define MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x280 0x650 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT10__UART1_RX_DATA 0x280 0x650 0x920 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x280 0x650 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT10__ARM_TRACE07 0x280 0x650 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11 0x284 0x654 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT11__AUD3_RXFS 0x284 0x654 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT11__ECSPI2_SS0 0x284 0x654 0x81c 0x2 0x2
+#define MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x284 0x654 0x920 0x3 0x1
+#define MX6QDL_PAD_CSI0_DAT11__UART1_TX_DATA 0x284 0x654 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x284 0x654 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT11__ARM_TRACE08 0x284 0x654 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x288 0x658 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT12__EIM_DATA08 0x288 0x658 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x288 0x658 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT12__UART4_RX_DATA 0x288 0x658 0x938 0x3 0x2
+#define MX6QDL_PAD_CSI0_DAT12__GPIO5_IO30 0x288 0x658 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT12__ARM_TRACE09 0x288 0x658 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x28c 0x65c 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT13__EIM_DATA09 0x28c 0x65c 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x28c 0x65c 0x938 0x3 0x3
+#define MX6QDL_PAD_CSI0_DAT13__UART4_TX_DATA 0x28c 0x65c 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31 0x28c 0x65c 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT13__ARM_TRACE10 0x28c 0x65c 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x290 0x660 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT14__EIM_DATA10 0x290 0x660 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x290 0x660 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT14__UART5_RX_DATA 0x290 0x660 0x940 0x3 0x2
+#define MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00 0x290 0x660 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT14__ARM_TRACE11 0x290 0x660 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x294 0x664 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT15__EIM_DATA11 0x294 0x664 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x294 0x664 0x940 0x3 0x3
+#define MX6QDL_PAD_CSI0_DAT15__UART5_TX_DATA 0x294 0x664 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT15__GPIO6_IO01 0x294 0x664 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT15__ARM_TRACE12 0x294 0x664 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x298 0x668 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT16__EIM_DATA12 0x298 0x668 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x298 0x668 0x934 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT16__UART4_CTS_B 0x298 0x668 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT16__GPIO6_IO02 0x298 0x668 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT16__ARM_TRACE13 0x298 0x668 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x29c 0x66c 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT17__EIM_DATA13 0x29c 0x66c 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x29c 0x66c 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT17__UART4_RTS_B 0x29c 0x66c 0x934 0x3 0x1
+#define MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x29c 0x66c 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT17__ARM_TRACE14 0x29c 0x66c 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x2a0 0x670 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT18__EIM_DATA14 0x2a0 0x670 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B 0x2a0 0x670 0x93c 0x3 0x2
+#define MX6QDL_PAD_CSI0_DAT18__UART5_CTS_B 0x2a0 0x670 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04 0x2a0 0x670 0x000 0x5 0x0
+#define MX6QDL_PAD_CSI0_DAT18__ARM_TRACE15 0x2a0 0x670 0x000 0x7 0x0
+#define MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x2a4 0x674 0x000 0x0 0x0
+#define MX6QDL_PAD_CSI0_DAT19__EIM_DATA15 0x2a4 0x674 0x000 0x1 0x0
+#define MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x2a4 0x674 0x000 0x3 0x0
+#define MX6QDL_PAD_CSI0_DAT19__UART5_RTS_B 0x2a4 0x674 0x93c 0x3 0x3
+#define MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05 0x2a4 0x674 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x2a8 0x690 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x2a8 0x690 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT7__UART1_RX_DATA 0x2a8 0x690 0x920 0x1 0x2
+#define MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x2a8 0x690 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x2ac 0x694 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x2ac 0x694 0x920 0x1 0x3
+#define MX6QDL_PAD_SD3_DAT6__UART1_TX_DATA 0x2ac 0x694 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x2ac 0x694 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x2b0 0x698 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x2b0 0x698 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT5__UART2_RX_DATA 0x2b0 0x698 0x928 0x1 0x4
+#define MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x2b0 0x698 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x2b4 0x69c 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x2b4 0x69c 0x928 0x1 0x5
+#define MX6QDL_PAD_SD3_DAT4__UART2_TX_DATA 0x2b4 0x69c 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x2b4 0x69c 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_CMD__SD3_CMD 0x2b8 0x6a0 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_CMD__UART2_CTS_B 0x2b8 0x6a0 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_CMD__UART2_RTS_B 0x2b8 0x6a0 0x924 0x1 0x2
+#define MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x2b8 0x6a0 0x000 0x2 0x0
+#define MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x2b8 0x6a0 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_CLK__SD3_CLK 0x2bc 0x6a4 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_CLK__UART2_RTS_B 0x2bc 0x6a4 0x924 0x1 0x3
+#define MX6QDL_PAD_SD3_CLK__UART2_CTS_B 0x2bc 0x6a4 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x2bc 0x6a4 0x7e4 0x2 0x2
+#define MX6QDL_PAD_SD3_CLK__GPIO7_IO03 0x2bc 0x6a4 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x2c0 0x6a8 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT0__UART1_CTS_B 0x2c0 0x6a8 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT0__UART1_RTS_B 0x2c0 0x6a8 0x91c 0x1 0x2
+#define MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x2c0 0x6a8 0x000 0x2 0x0
+#define MX6QDL_PAD_SD3_DAT0__GPIO7_IO04 0x2c0 0x6a8 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x2c4 0x6ac 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT1__UART1_RTS_B 0x2c4 0x6ac 0x91c 0x1 0x3
+#define MX6QDL_PAD_SD3_DAT1__UART1_CTS_B 0x2c4 0x6ac 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x2c4 0x6ac 0x7e8 0x2 0x1
+#define MX6QDL_PAD_SD3_DAT1__GPIO7_IO05 0x2c4 0x6ac 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x2c8 0x6b0 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x2c8 0x6b0 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x2cc 0x6b4 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_DAT3__UART3_CTS_B 0x2cc 0x6b4 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_DAT3__UART3_RTS_B 0x2cc 0x6b4 0x92c 0x1 0x4
+#define MX6QDL_PAD_SD3_DAT3__GPIO7_IO07 0x2cc 0x6b4 0x000 0x5 0x0
+#define MX6QDL_PAD_SD3_RST__SD3_RESET 0x2d0 0x6b8 0x000 0x0 0x0
+#define MX6QDL_PAD_SD3_RST__UART3_RTS_B 0x2d0 0x6b8 0x92c 0x1 0x5
+#define MX6QDL_PAD_SD3_RST__UART3_CTS_B 0x2d0 0x6b8 0x000 0x1 0x0
+#define MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x2d0 0x6b8 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CLE__NAND_CLE 0x2d4 0x6bc 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_CLE__IPU2_SISG4 0x2d4 0x6bc 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x2d4 0x6bc 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_ALE__NAND_ALE 0x2d8 0x6c0 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_ALE__SD4_RESET 0x2d8 0x6c0 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x2d8 0x6c0 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0x2dc 0x6c4 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_WP_B__IPU2_SISG5 0x2dc 0x6c4 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x2dc 0x6c4 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0x2e0 0x6c8 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_RB0__IPU2_DI0_PIN01 0x2e0 0x6c8 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x2e0 0x6c8 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0x2e4 0x6cc 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x2e4 0x6cc 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0x2e8 0x6d0 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_CS1__SD4_VSELECT 0x2e8 0x6d0 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x2e8 0x6d0 0x000 0x2 0x0
+#define MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x2e8 0x6d0 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CS2__NAND_CE2_B 0x2ec 0x6d4 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_CS2__IPU1_SISG0 0x2ec 0x6d4 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_CS2__ESAI_TX0 0x2ec 0x6d4 0x874 0x2 0x1
+#define MX6QDL_PAD_NANDF_CS2__EIM_CRE 0x2ec 0x6d4 0x000 0x3 0x0
+#define MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x2ec 0x6d4 0x000 0x4 0x0
+#define MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x2ec 0x6d4 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CS2__IPU2_SISG0 0x2ec 0x6d4 0x000 0x6 0x0
+#define MX6QDL_PAD_NANDF_CS3__NAND_CE3_B 0x2f0 0x6d8 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_CS3__IPU1_SISG1 0x2f0 0x6d8 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_CS3__ESAI_TX1 0x2f0 0x6d8 0x878 0x2 0x1
+#define MX6QDL_PAD_NANDF_CS3__EIM_ADDR26 0x2f0 0x6d8 0x000 0x3 0x0
+#define MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x2f0 0x6d8 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_CS3__IPU2_SISG1 0x2f0 0x6d8 0x000 0x6 0x0
+#define MX6QDL_PAD_SD4_CMD__SD4_CMD 0x2f4 0x6dc 0x000 0x0 0x0
+#define MX6QDL_PAD_SD4_CMD__NAND_RE_B 0x2f4 0x6dc 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_CMD__UART3_TX_DATA 0x2f4 0x6dc 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_CMD__UART3_RX_DATA 0x2f4 0x6dc 0x930 0x2 0x2
+#define MX6QDL_PAD_SD4_CMD__GPIO7_IO09 0x2f4 0x6dc 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_CLK__SD4_CLK 0x2f8 0x6e0 0x000 0x0 0x0
+#define MX6QDL_PAD_SD4_CLK__NAND_WE_B 0x2f8 0x6e0 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_CLK__UART3_RX_DATA 0x2f8 0x6e0 0x930 0x2 0x3
+#define MX6QDL_PAD_SD4_CLK__UART3_TX_DATA 0x2f8 0x6e0 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_CLK__GPIO7_IO10 0x2f8 0x6e0 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D0__NAND_DATA00 0x2fc 0x6e4 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D0__SD1_DATA4 0x2fc 0x6e4 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x2fc 0x6e4 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D1__NAND_DATA01 0x300 0x6e8 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D1__SD1_DATA5 0x300 0x6e8 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x300 0x6e8 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D2__NAND_DATA02 0x304 0x6ec 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D2__SD1_DATA6 0x304 0x6ec 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x304 0x6ec 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D3__NAND_DATA03 0x308 0x6f0 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D3__SD1_DATA7 0x308 0x6f0 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x308 0x6f0 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D4__NAND_DATA04 0x30c 0x6f4 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D4__SD2_DATA4 0x30c 0x6f4 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x30c 0x6f4 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D5__NAND_DATA05 0x310 0x6f8 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D5__SD2_DATA5 0x310 0x6f8 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x310 0x6f8 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D6__NAND_DATA06 0x314 0x6fc 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D6__SD2_DATA6 0x314 0x6fc 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x314 0x6fc 0x000 0x5 0x0
+#define MX6QDL_PAD_NANDF_D7__NAND_DATA07 0x318 0x700 0x000 0x0 0x0
+#define MX6QDL_PAD_NANDF_D7__SD2_DATA7 0x318 0x700 0x000 0x1 0x0
+#define MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x318 0x700 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x31c 0x704 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x31c 0x704 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x31c 0x704 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x320 0x708 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x320 0x708 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x320 0x708 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x324 0x70c 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x324 0x70c 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x324 0x70c 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x328 0x710 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x328 0x710 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x32c 0x714 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x32c 0x714 0x928 0x2 0x6
+#define MX6QDL_PAD_SD4_DAT4__UART2_TX_DATA 0x32c 0x714 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x32c 0x714 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x330 0x718 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x330 0x718 0x924 0x2 0x4
+#define MX6QDL_PAD_SD4_DAT5__UART2_CTS_B 0x330 0x718 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT5__GPIO2_IO13 0x330 0x718 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x334 0x71c 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x334 0x71c 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT6__UART2_RTS_B 0x334 0x71c 0x924 0x2 0x5
+#define MX6QDL_PAD_SD4_DAT6__GPIO2_IO14 0x334 0x71c 0x000 0x5 0x0
+#define MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x338 0x720 0x000 0x1 0x0
+#define MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x338 0x720 0x000 0x2 0x0
+#define MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA 0x338 0x720 0x928 0x2 0x7
+#define MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x338 0x720 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x33c 0x724 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_DAT1__ECSPI5_SS0 0x33c 0x724 0x834 0x1 0x1
+#define MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x33c 0x724 0x000 0x2 0x0
+#define MX6QDL_PAD_SD1_DAT1__GPT_CAPTURE2 0x33c 0x724 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x33c 0x724 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x340 0x728 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_DAT0__ECSPI5_MISO 0x340 0x728 0x82c 0x1 0x1
+#define MX6QDL_PAD_SD1_DAT0__GPT_CAPTURE1 0x340 0x728 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x340 0x728 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x344 0x72c 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_DAT3__ECSPI5_SS2 0x344 0x72c 0x000 0x1 0x0
+#define MX6QDL_PAD_SD1_DAT3__GPT_COMPARE3 0x344 0x72c 0x000 0x2 0x0
+#define MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x344 0x72c 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_DAT3__WDOG2_B 0x344 0x72c 0x000 0x4 0x0
+#define MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x344 0x72c 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT3__WDOG2_RESET_B_DEB 0x344 0x72c 0x000 0x6 0x0
+#define MX6QDL_PAD_SD1_CMD__SD1_CMD 0x348 0x730 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_CMD__ECSPI5_MOSI 0x348 0x730 0x830 0x1 0x0
+#define MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x348 0x730 0x000 0x2 0x0
+#define MX6QDL_PAD_SD1_CMD__GPT_COMPARE1 0x348 0x730 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_CMD__GPIO1_IO18 0x348 0x730 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x34c 0x734 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_DAT2__ECSPI5_SS1 0x34c 0x734 0x838 0x1 0x1
+#define MX6QDL_PAD_SD1_DAT2__GPT_COMPARE2 0x34c 0x734 0x000 0x2 0x0
+#define MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x34c 0x734 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_DAT2__WDOG1_B 0x34c 0x734 0x000 0x4 0x0
+#define MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x34c 0x734 0x000 0x5 0x0
+#define MX6QDL_PAD_SD1_DAT2__WDOG1_RESET_B_DEB 0x34c 0x734 0x000 0x6 0x0
+#define MX6QDL_PAD_SD1_CLK__SD1_CLK 0x350 0x738 0x000 0x0 0x0
+#define MX6QDL_PAD_SD1_CLK__ECSPI5_SCLK 0x350 0x738 0x828 0x1 0x0
+#define MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT 0x350 0x738 0x000 0x2 0x0
+#define MX6QDL_PAD_SD1_CLK__GPT_CLKIN 0x350 0x738 0x000 0x3 0x0
+#define MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x350 0x738 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_CLK__SD2_CLK 0x354 0x73c 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_CLK__ECSPI5_SCLK 0x354 0x73c 0x828 0x1 0x1
+#define MX6QDL_PAD_SD2_CLK__KEY_COL5 0x354 0x73c 0x8e8 0x2 0x3
+#define MX6QDL_PAD_SD2_CLK__AUD4_RXFS 0x354 0x73c 0x7c0 0x3 0x1
+#define MX6QDL_PAD_SD2_CLK__GPIO1_IO10 0x354 0x73c 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_CMD__SD2_CMD 0x358 0x740 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_CMD__ECSPI5_MOSI 0x358 0x740 0x830 0x1 0x1
+#define MX6QDL_PAD_SD2_CMD__KEY_ROW5 0x358 0x740 0x8f4 0x2 0x2
+#define MX6QDL_PAD_SD2_CMD__AUD4_RXC 0x358 0x740 0x7bc 0x3 0x1
+#define MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x358 0x740 0x000 0x5 0x0
+#define MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x35c 0x744 0x000 0x0 0x0
+#define MX6QDL_PAD_SD2_DAT3__ECSPI5_SS3 0x35c 0x744 0x000 0x1 0x0
+#define MX6QDL_PAD_SD2_DAT3__KEY_COL6 0x35c 0x744 0x8ec 0x2 0x2
+#define MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x35c 0x744 0x7c4 0x3 0x1
+#define MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x35c 0x744 0x000 0x5 0x0
+
+#endif /* __DTS_IMX6Q_PINFUNC_H */
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 17/21] arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (15 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 16/21] arm: dts: imx6q: Add pinctrl defines Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 18/21] mtd: nand: Kconfig: Add NAND_MXS entry Jagan Teki
` (4 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
i.CoreM6 Quad/Dual modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DQ, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/Makefile | 3 ++-
arch/arm/dts/imx6q-icore.dts | 59 ++++++++++++++++++++++++++++++++++++++++++++
board/engicam/icorem6/README | 9 ++++++-
3 files changed, 69 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/dts/imx6q-icore.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 1994fc8..ad69a2c 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -282,7 +282,8 @@ dtb-$(CONFIG_VF610) += vf500-colibri.dtb \
bk4r1.dtb
dtb-$(CONFIG_MX6) += imx6ull-14x14-evk.dtb \
- imx6dl-icore.dtb
+ imx6dl-icore.dtb \
+ imx6q-icore.dtb
dtb-$(CONFIG_MX7) += imx7-colibri.dtb
diff --git a/arch/arm/dts/imx6q-icore.dts b/arch/arm/dts/imx6q-icore.dts
new file mode 100644
index 0000000..025f543
--- /dev/null
+++ b/arch/arm/dts/imx6q-icore.dts
@@ -0,0 +1,59 @@
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-icore.dtsi"
+
+/ {
+ model = "Engicam i.CoreM6 Quad/Dual Starter Kit";
+ compatible = "engicam,imx6-icore", "fsl,imx6q";
+};
+
+&can1 {
+ status = "okay";
+};
+
+&can2 {
+ status = "okay";
+};
diff --git a/board/engicam/icorem6/README b/board/engicam/icorem6/README
index c264a94..12d1e21 100644
--- a/board/engicam/icorem6/README
+++ b/board/engicam/icorem6/README
@@ -1,12 +1,19 @@
How to use U-Boot on Engicam i.CoreM6 DualLite/Solo and Quad/Dual Starter Kit:
-----------------------------------------------------------------------------
-- Build U-Boot for Engicam i.CoreM6 QDL:
+- Configure U-Boot for Engicam i.CoreM6 QDL:
$ make mrproper
$ make icorem6qdl_mmc_defconfig
+
+- Build for i.CoreM6 DualLite/Solo
+
$ make
+- Build for i.CoreM6 Quad/Dual
+
+$ make DEVICE_TREE=imx6q-icore
+
This will generate the SPL image called SPL and the u-boot-dtb.img.
- Flash the SPL image into the micro SD card:
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 18/21] mtd: nand: Kconfig: Add NAND_MXS entry
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (16 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 17/21] arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-11 22:10 ` Jörg Krause
2016-10-08 12:30 ` [U-Boot] [PATCH v7 19/21] imx6: icorem6: Add NAND support Jagan Teki
` (3 subsequent siblings)
21 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Added kconfig for NAND_MXS driver.
Cc: Scott Wood <oss@buserror.net>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
drivers/mtd/nand/Kconfig | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 5ce7d6d..df154bf 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -80,6 +80,13 @@ config NAND_ARASAN
controller. This uses the hardware ECC for read and
write operations.
+config NAND_MXS
+ bool "MXS NAND support"
+ depends on MX6
+ help
+ This enables NAND driver for the NAND flash controller on the
+ MXS processors.
+
comment "Generic NAND options"
# Enhance depends when converting drivers to Kconfig which use this config
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 19/21] imx6: icorem6: Add NAND support
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (17 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 18/21] mtd: nand: Kconfig: Add NAND_MXS entry Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 20/21] imx6: icorem6: Enable MTD device support Jagan Teki
` (2 subsequent siblings)
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add NAND support for Engicam i.CoreM6 qdl board.
Boot Log:
--------
U-Boot SPL 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43)
Trying to boot from NAND
NAND : 512 MiB
U-Boot 2016.09-rc2-30755-gd3dc581-dirty (Sep 28 2016 - 23:00:43 +0530)
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 55C
Reset cause: WDOG
Model: Engicam i.CoreM6 DualLite/Solo Starter Kit
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
icorem6qdl>
Cc: Scott Wood <oss@buserror.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/icorem6/icorem6.c | 63 ++++++++++++++++++++++++++++++++++++
configs/imx6qdl_icore_nand_defconfig | 37 +++++++++++++++++++++
include/configs/imx6qdl_icore.h | 25 +++++++++++++-
3 files changed, 124 insertions(+), 1 deletion(-)
create mode 100644 configs/imx6qdl_icore_nand_defconfig
diff --git a/board/engicam/icorem6/icorem6.c b/board/engicam/icorem6/icorem6.c
index a370c8b..c152007 100644
--- a/board/engicam/icorem6/icorem6.c
+++ b/board/engicam/icorem6/icorem6.c
@@ -101,6 +101,66 @@ int board_eth_init(bd_t *bis)
}
#endif
+#ifdef CONFIG_NAND_MXS
+
+#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
+#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
+ PAD_CTL_SRE_FAST)
+#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
+
+iomux_v3_cfg_t gpmi_pads[] = {
+ IOMUX_PADS(PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL0)),
+ IOMUX_PADS(PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+ IOMUX_PADS(PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2)),
+};
+
+static void setup_gpmi_nand(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /* config gpmi nand iomux */
+ SETUP_IOMUX_PADS(gpmi_pads);
+
+ /* gate ENFC_CLK_ROOT clock first,before clk source switch */
+ clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
+ /* config gpmi and bch clock to 100 MHz */
+ clrsetbits_le32(&mxc_ccm->cs2cdr,
+ MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
+ MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
+ MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
+ MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
+
+ /* enable ENFC_CLK_ROOT clock */
+ setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
+ /* enable gpmi and bch clock gating */
+ setbits_le32(&mxc_ccm->CCGR4,
+ MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+ MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+ MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
+
+ /* enable apbh clock gating */
+ setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+#endif
+
int board_early_init_f(void)
{
SETUP_IOMUX_PADS(uart4_pads);
@@ -113,6 +173,9 @@ int board_init(void)
/* Address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+#ifdef CONFIG_NAND_MXS
+ setup_gpmi_nand();
+#endif
return 0;
}
diff --git a/configs/imx6qdl_icore_nand_defconfig b/configs/imx6qdl_icore_nand_defconfig
new file mode 100644
index 0000000..8ac3099
--- /dev/null
+++ b/configs/imx6qdl_icore_nand_defconfig
@@ -0,0 +1,37 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_MX6Q_ICORE=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,ENV_IS_IN_NAND"
+CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
+CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
+CONFIG_SYS_PROMPT="icorem6qdl> "
+CONFIG_SPL=y
+CONFIG_BOOTDELAY=3
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_DISPLAY_CPUINFO=y
+CONFIG_HUSH_PARSER=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_SYS_MAXARGS=32
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_CACHE=y
+CONFIG_OF_LIBFDT=y
+CONFIG_FEC_MXC=y
+CONFIG_MXC_UART=y
+CONFIG_NAND_MXS=y
+CONFIG_NETDEVICES=y
+CONFIG_IMX_THERMAL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_SPL_DMA_SUPPORT=y
diff --git a/include/configs/imx6qdl_icore.h b/include/configs/imx6qdl_icore.h
index 6b58447..cd3aa43 100644
--- a/include/configs/imx6qdl_icore.h
+++ b/include/configs/imx6qdl_icore.h
@@ -27,6 +27,10 @@
/* Environment in MMC */
# if defined(CONFIG_ENV_IS_IN_MMC)
# define CONFIG_ENV_OFFSET 0x100000
+/* Environment in NAND */
+# elif defined(CONFIG_ENV_IS_IN_NAND)
+# define CONFIG_ENV_OFFSET 0x400000
+# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
# endif
#endif
@@ -111,6 +115,20 @@
# define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
#endif
+/* NAND */
+#ifdef CONFIG_NAND_MXS
+# define CONFIG_SYS_MAX_NAND_DEVICE 1
+# define CONFIG_SYS_NAND_BASE 0x40000000
+# define CONFIG_SYS_NAND_5_ADDR_CYCLE
+# define CONFIG_SYS_NAND_ONFI_DETECTION
+# define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+# define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
+
+# define CONFIG_APBH_DMA
+# define CONFIG_APBH_DMA_BURST
+# define CONFIG_APBH_DMA_BURST8
+#endif
+
/* Ethernet */
#ifdef CONFIG_FEC_MXC
# define IMX_FEC_BASE ENET_BASE_ADDR
@@ -125,7 +143,12 @@
/* SPL */
#ifdef CONFIG_SPL
-# define CONFIG_SPL_MMC_SUPPORT
+# ifdef CONFIG_NAND_MXS
+# define CONFIG_SPL_NAND_SUPPORT
+# else
+# define CONFIG_SPL_MMC_SUPPORT
+# endif
+
# include "imx6_spl.h"
# ifdef CONFIG_SPL_BUILD
# undef CONFIG_DM_GPIO
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 20/21] imx6: icorem6: Enable MTD device support
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (18 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 19/21] imx6: icorem6: Add NAND support Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 21/21] imx6: icorem6: Add default mtd nand partition table Jagan Teki
2016-10-09 14:45 ` [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Enable MTD device, partition and command support.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
include/configs/imx6qdl_icore.h | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/include/configs/imx6qdl_icore.h b/include/configs/imx6qdl_icore.h
index cd3aa43..6e33ec3 100644
--- a/include/configs/imx6qdl_icore.h
+++ b/include/configs/imx6qdl_icore.h
@@ -124,6 +124,12 @@
# define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
# define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
+/* MTD device */
+# define CONFIG_MTD_DEVICE
+# define CONFIG_CMD_MTDPARTS
+# define CONFIG_MTD_PARTITIONS
+# define MTDIDS_DEFAULT "nand0=nand"
+
# define CONFIG_APBH_DMA
# define CONFIG_APBH_DMA_BURST
# define CONFIG_APBH_DMA_BURST8
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 21/21] imx6: icorem6: Add default mtd nand partition table
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (19 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 20/21] imx6: icorem6: Enable MTD device support Jagan Teki
@ 2016-10-08 12:30 ` Jagan Teki
2016-10-09 14:45 ` [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
21 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-08 12:30 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
icorem6qdl> mtdparts
device nand0 <nand>, # parts = 6
0: spl 0x00200000 0x00000000 0
1: uboot 0x00200000 0x00200000 0
2: env 0x00100000 0x00400000 0
3: kernel 0x00400000 0x00500000 0
4: dtb 0x00100000 0x00900000 0
5: rootfs 0x1f600000 0x00a00000 0
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
include/configs/imx6qdl_icore.h | 2 ++
1 file changed, 2 insertions(+)
diff --git a/include/configs/imx6qdl_icore.h b/include/configs/imx6qdl_icore.h
index 6e33ec3..f8a1263 100644
--- a/include/configs/imx6qdl_icore.h
+++ b/include/configs/imx6qdl_icore.h
@@ -129,6 +129,8 @@
# define CONFIG_CMD_MTDPARTS
# define CONFIG_MTD_PARTITIONS
# define MTDIDS_DEFAULT "nand0=nand"
+# define MTDPARTS_DEFAULT "mtdparts=nand:2m(spl),2m(uboot)," \
+ "1m(env),4m(kernel),1m(dtb),-(rootfs)"
# define CONFIG_APBH_DMA
# define CONFIG_APBH_DMA_BURST
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
` (20 preceding siblings ...)
2016-10-08 12:30 ` [U-Boot] [PATCH v7 21/21] imx6: icorem6: Add default mtd nand partition table Jagan Teki
@ 2016-10-09 14:45 ` Jagan Teki
2016-10-11 3:30 ` Jagan Teki
21 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-09 14:45 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki@openedev.com> wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
>
> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
> and test on the respective starter kits as well.
>
> Tested both MMC and NAND boot.
>
> Changes for v7:
> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
> - Rebase on u-boot-imx/master
>
> Changes for v6:
> - Rebase to u-boot-imx/master
> - Move few SPL configs to defconfigs
>
> Changes for v5:
> - Add NAND support
>
> Changes for v4:
> - Add 'net: Kconfig: Add FEC_MXC entry' patch
> - Updated ENV configs along with comments
> - Restructured configs for more readability
> - Add CONFIG_ENV_OVERWRITE
> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>
> Changes for v3:
> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
> - Add minimal devicetree support for Engicam i.CoreM6 QDL
> - Add is_mx6dl()
> - Add is_mx6solo()
> - Use is_mx6dq()
> - Add last commit sha1 and header in pull devicetree files from Linux
>
> Changes for v2:
> - Make static to local iomux structure in board file
> - Corrected rowaddr in mx6_ddr3_cfg
> - Used imx_ddr_size
> - Add FEC support and tested the same
> - Add DM_GPIO, DM_MMC support
> - Add pinctrl support
> - Add devicetree support
>
> Jagan Teki (21):
> serial: Kconfig: Add MXC_UART entry
> thermal: Kconfig: Add IMX_THERMAL entry
> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
> net: Kconfig: Add FEC_MXC entry
> imx6: icorem6: Add ENET support
> imx: s/docs\/README.imximage/doc\/README.imximage/g
> arm: dts: Add devicetree for i.MX6DL
> arm: dts: Add devicetree for i.MX6DQL
> arm: dts: imx6dl: Add pinctrl defines
> dt-bindings: clock: imx6qdl: Add clock defines
> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
> imx6q: icorem6: Enable pinctrl driver
> engicam: icorem6: Add DM_GPIO, DM_MMC support
> arm: dts: Add devicetree for i.MX6Q
> arm: dts: imx6q: Add pinctrl defines
> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
> mtd: nand: Kconfig: Add NAND_MXS entry
> imx6: icorem6: Add NAND support
> imx6: icorem6: Enable MTD device support
> imx6: icorem6: Add default mtd nand partition table
All set now, please do apply.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-09 14:45 ` [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
@ 2016-10-11 3:30 ` Jagan Teki
2016-10-17 3:40 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-11 3:30 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki@gmail.com> wrote:
> Hi Stefano,
>
> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki@openedev.com> wrote:
>> From: Jagan Teki <jagan@amarulasolutions.com>
>>
>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>> and test on the respective starter kits as well.
>>
>> Tested both MMC and NAND boot.
>>
>> Changes for v7:
>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>> - Rebase on u-boot-imx/master
>>
>> Changes for v6:
>> - Rebase to u-boot-imx/master
>> - Move few SPL configs to defconfigs
>>
>> Changes for v5:
>> - Add NAND support
>>
>> Changes for v4:
>> - Add 'net: Kconfig: Add FEC_MXC entry' patch
>> - Updated ENV configs along with comments
>> - Restructured configs for more readability
>> - Add CONFIG_ENV_OVERWRITE
>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>
>> Changes for v3:
>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>> - Add minimal devicetree support for Engicam i.CoreM6 QDL
>> - Add is_mx6dl()
>> - Add is_mx6solo()
>> - Use is_mx6dq()
>> - Add last commit sha1 and header in pull devicetree files from Linux
>>
>> Changes for v2:
>> - Make static to local iomux structure in board file
>> - Corrected rowaddr in mx6_ddr3_cfg
>> - Used imx_ddr_size
>> - Add FEC support and tested the same
>> - Add DM_GPIO, DM_MMC support
>> - Add pinctrl support
>> - Add devicetree support
>>
>> Jagan Teki (21):
>> serial: Kconfig: Add MXC_UART entry
>> thermal: Kconfig: Add IMX_THERMAL entry
>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>> net: Kconfig: Add FEC_MXC entry
>> imx6: icorem6: Add ENET support
>> imx: s/docs\/README.imximage/doc\/README.imximage/g
>> arm: dts: Add devicetree for i.MX6DL
>> arm: dts: Add devicetree for i.MX6DQL
>> arm: dts: imx6dl: Add pinctrl defines
>> dt-bindings: clock: imx6qdl: Add clock defines
>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>> imx6q: icorem6: Enable pinctrl driver
>> engicam: icorem6: Add DM_GPIO, DM_MMC support
>> arm: dts: Add devicetree for i.MX6Q
>> arm: dts: imx6q: Add pinctrl defines
>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>> mtd: nand: Kconfig: Add NAND_MXS entry
>> imx6: icorem6: Add NAND support
>> imx6: icorem6: Enable MTD device support
>> imx6: icorem6: Add default mtd nand partition table
>
> All set now, please do apply.
Let me know if you still find any issues, otherwise apply this.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 18/21] mtd: nand: Kconfig: Add NAND_MXS entry
2016-10-08 12:30 ` [U-Boot] [PATCH v7 18/21] mtd: nand: Kconfig: Add NAND_MXS entry Jagan Teki
@ 2016-10-11 22:10 ` Jörg Krause
2016-10-11 22:24 ` Sergey Kubushyn
2016-10-12 5:50 ` Jagan Teki
0 siblings, 2 replies; 48+ messages in thread
From: Jörg Krause @ 2016-10-11 22:10 UTC (permalink / raw)
To: u-boot
On Sa, 2016-10-08 at 18:00 +0530, Jagan Teki wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
>
> Added kconfig for NAND_MXS driver.
>
> Cc: Scott Wood <oss@buserror.net>
> Cc: Simon Glass <sjg@chromium.org>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Peng Fan <peng.fan@nxp.com>
> Cc: Matteo Lisi <matteo.lisi@engicam.com>
> Cc: Michael Trimarchi <michael@amarulasolutions.com>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> ?drivers/mtd/nand/Kconfig | 7 +++++++
> ?1 file changed, 7 insertions(+)
>
> diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
> index 5ce7d6d..df154bf 100644
> --- a/drivers/mtd/nand/Kconfig
> +++ b/drivers/mtd/nand/Kconfig
> @@ -80,6 +80,13 @@ config NAND_ARASAN
> ? ??controller. This uses the hardware ECC for read and
> ? ??write operations.
> ?
> +config NAND_MXS
> + bool "MXS NAND support"
> + depends on MX6
Isn't mxs supposed to be i.MX23/i.MX28 and not i.MX6?
> + help
> + ??This enables NAND driver for the NAND flash controller on
> the
> + ??MXS processors.
> +
> ?comment "Generic NAND options"
> ?
> ?# Enhance depends when converting drivers to Kconfig which use this
> config
Best regards
J?rg Krause
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 18/21] mtd: nand: Kconfig: Add NAND_MXS entry
2016-10-11 22:10 ` Jörg Krause
@ 2016-10-11 22:24 ` Sergey Kubushyn
2016-10-12 5:50 ` Jagan Teki
1 sibling, 0 replies; 48+ messages in thread
From: Sergey Kubushyn @ 2016-10-11 22:24 UTC (permalink / raw)
To: u-boot
On Wed, 12 Oct 2016, J?rg Krause wrote:
> On Sa, 2016-10-08 at 18:00 +0530, Jagan Teki wrote:
>> From: Jagan Teki <jagan@amarulasolutions.com>
>>
>> Added kconfig for NAND_MXS driver.
>>
>> Cc: Scott Wood <oss@buserror.net>
>> Cc: Simon Glass <sjg@chromium.org>
>> Cc: Fabio Estevam <fabio.estevam@nxp.com>
>> Cc: Stefano Babic <sbabic@denx.de>
>> Cc: Peng Fan <peng.fan@nxp.com>
>> Cc: Matteo Lisi <matteo.lisi@engicam.com>
>> Cc: Michael Trimarchi <michael@amarulasolutions.com>
>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>> ---
>> ?drivers/mtd/nand/Kconfig | 7 +++++++
>> ?1 file changed, 7 insertions(+)
>>
>> diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
>> index 5ce7d6d..df154bf 100644
>> --- a/drivers/mtd/nand/Kconfig
>> +++ b/drivers/mtd/nand/Kconfig
>> @@ -80,6 +80,13 @@ config NAND_ARASAN
>> ? ??controller. This uses the hardware ECC for read and
>> ? ??write operations.
>> ?
>> +config NAND_MXS
>> + bool "MXS NAND support"
>> + depends on MX6
>
> Isn't mxs supposed to be i.MX23/i.MX28 and not i.MX6?
i.MX6 has the same MXS NAND controller.
---
******************************************************************
* KSI at home KOI8 Net < > The impossible we do immediately. *
* Las Vegas NV, USA < > Miracles require 24-hour notice. *
******************************************************************
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 18/21] mtd: nand: Kconfig: Add NAND_MXS entry
2016-10-11 22:10 ` Jörg Krause
2016-10-11 22:24 ` Sergey Kubushyn
@ 2016-10-12 5:50 ` Jagan Teki
2016-10-12 6:19 ` Jörg Krause
1 sibling, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-12 5:50 UTC (permalink / raw)
To: u-boot
On Wed, Oct 12, 2016 at 3:40 AM, J?rg Krause
<joerg.krause@embedded.rocks> wrote:
> On Sa, 2016-10-08 at 18:00 +0530, Jagan Teki wrote:
>> From: Jagan Teki <jagan@amarulasolutions.com>
>>
>> Added kconfig for NAND_MXS driver.
>>
>> Cc: Scott Wood <oss@buserror.net>
>> Cc: Simon Glass <sjg@chromium.org>
>> Cc: Fabio Estevam <fabio.estevam@nxp.com>
>> Cc: Stefano Babic <sbabic@denx.de>
>> Cc: Peng Fan <peng.fan@nxp.com>
>> Cc: Matteo Lisi <matteo.lisi@engicam.com>
>> Cc: Michael Trimarchi <michael@amarulasolutions.com>
>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>> ---
>> drivers/mtd/nand/Kconfig | 7 +++++++
>> 1 file changed, 7 insertions(+)
>>
>> diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
>> index 5ce7d6d..df154bf 100644
>> --- a/drivers/mtd/nand/Kconfig
>> +++ b/drivers/mtd/nand/Kconfig
>> @@ -80,6 +80,13 @@ config NAND_ARASAN
>> controller. This uses the hardware ECC for read and
>> write operations.
>>
>> +config NAND_MXS
>> + bool "MXS NAND support"
>> + depends on MX6
>
> Isn't mxs supposed to be i.MX23/i.MX28 and not i.MX6?
Yes will ||ed once the nand config used by MX23/28 are planing to move
defconfig.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 18/21] mtd: nand: Kconfig: Add NAND_MXS entry
2016-10-12 5:50 ` Jagan Teki
@ 2016-10-12 6:19 ` Jörg Krause
0 siblings, 0 replies; 48+ messages in thread
From: Jörg Krause @ 2016-10-12 6:19 UTC (permalink / raw)
To: u-boot
On Mi, 2016-10-12 at 11:20 +0530, Jagan Teki wrote:
> On Wed, Oct 12, 2016 at 3:40 AM, J?rg Krause
> <joerg.krause@embedded.rocks> wrote:
> >
> > On Sa, 2016-10-08 at 18:00 +0530, Jagan Teki wrote:
> > >
> > > From: Jagan Teki <jagan@amarulasolutions.com>
> > >
> > > Added kconfig for NAND_MXS driver.
> > >
> > > Cc: Scott Wood <oss@buserror.net>
> > > Cc: Simon Glass <sjg@chromium.org>
> > > Cc: Fabio Estevam <fabio.estevam@nxp.com>
> > > Cc: Stefano Babic <sbabic@denx.de>
> > > Cc: Peng Fan <peng.fan@nxp.com>
> > > Cc: Matteo Lisi <matteo.lisi@engicam.com>
> > > Cc: Michael Trimarchi <michael@amarulasolutions.com>
> > > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> > > ---
> > > ?drivers/mtd/nand/Kconfig | 7 +++++++
> > > ?1 file changed, 7 insertions(+)
> > >
> > > diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
> > > index 5ce7d6d..df154bf 100644
> > > --- a/drivers/mtd/nand/Kconfig
> > > +++ b/drivers/mtd/nand/Kconfig
> > > @@ -80,6 +80,13 @@ config NAND_ARASAN
> > > ????????controller. This uses the hardware ECC for read and
> > > ????????write operations.
> > >
> > > +config NAND_MXS
> > > +?????bool "MXS NAND support"
> > > +?????depends on MX6
> >
> > Isn't mxs supposed to be i.MX23/i.MX28 and not i.MX6?
>
> Yes will ||ed once the nand config used by MX23/28 are planing to
> move
> defconfig.
I see! Thanks!
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-11 3:30 ` Jagan Teki
@ 2016-10-17 3:40 ` Jagan Teki
2016-10-17 5:56 ` Stefano Babic
0 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-17 3:40 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jteki@openedev.com> wrote:
> Hi Stefano,
>
> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki@gmail.com> wrote:
>> Hi Stefano,
>>
>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki@openedev.com> wrote:
>>> From: Jagan Teki <jagan@amarulasolutions.com>
>>>
>>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>>> and test on the respective starter kits as well.
>>>
>>> Tested both MMC and NAND boot.
>>>
>>> Changes for v7:
>>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>> - Rebase on u-boot-imx/master
>>>
>>> Changes for v6:
>>> - Rebase to u-boot-imx/master
>>> - Move few SPL configs to defconfigs
>>>
>>> Changes for v5:
>>> - Add NAND support
>>>
>>> Changes for v4:
>>> - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>> - Updated ENV configs along with comments
>>> - Restructured configs for more readability
>>> - Add CONFIG_ENV_OVERWRITE
>>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>
>>> Changes for v3:
>>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>> - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>> - Add is_mx6dl()
>>> - Add is_mx6solo()
>>> - Use is_mx6dq()
>>> - Add last commit sha1 and header in pull devicetree files from Linux
>>>
>>> Changes for v2:
>>> - Make static to local iomux structure in board file
>>> - Corrected rowaddr in mx6_ddr3_cfg
>>> - Used imx_ddr_size
>>> - Add FEC support and tested the same
>>> - Add DM_GPIO, DM_MMC support
>>> - Add pinctrl support
>>> - Add devicetree support
>>>
>>> Jagan Teki (21):
>>> serial: Kconfig: Add MXC_UART entry
>>> thermal: Kconfig: Add IMX_THERMAL entry
>>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>> net: Kconfig: Add FEC_MXC entry
>>> imx6: icorem6: Add ENET support
>>> imx: s/docs\/README.imximage/doc\/README.imximage/g
>>> arm: dts: Add devicetree for i.MX6DL
>>> arm: dts: Add devicetree for i.MX6DQL
>>> arm: dts: imx6dl: Add pinctrl defines
>>> dt-bindings: clock: imx6qdl: Add clock defines
>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>> imx6q: icorem6: Enable pinctrl driver
>>> engicam: icorem6: Add DM_GPIO, DM_MMC support
>>> arm: dts: Add devicetree for i.MX6Q
>>> arm: dts: imx6q: Add pinctrl defines
>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>> mtd: nand: Kconfig: Add NAND_MXS entry
>>> imx6: icorem6: Add NAND support
>>> imx6: icorem6: Enable MTD device support
>>> imx6: icorem6: Add default mtd nand partition table
>>
>> All set now, please do apply.
>
> Let me know if you still find any issues, otherwise apply this.
>
Any help?
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-17 3:40 ` Jagan Teki
@ 2016-10-17 5:56 ` Stefano Babic
2016-10-24 7:53 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Stefano Babic @ 2016-10-17 5:56 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On 17/10/2016 05:40, Jagan Teki wrote:
> Hi Stefano,
>
> On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jteki@openedev.com> wrote:
>> Hi Stefano,
>>
>> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki@gmail.com> wrote:
>>> Hi Stefano,
>>>
>>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki@openedev.com> wrote:
>>>> From: Jagan Teki <jagan@amarulasolutions.com>
>>>>
>>>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>>>> and test on the respective starter kits as well.
>>>>
>>>> Tested both MMC and NAND boot.
>>>>
>>>> Changes for v7:
>>>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>> - Rebase on u-boot-imx/master
>>>>
>>>> Changes for v6:
>>>> - Rebase to u-boot-imx/master
>>>> - Move few SPL configs to defconfigs
>>>>
>>>> Changes for v5:
>>>> - Add NAND support
>>>>
>>>> Changes for v4:
>>>> - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>>> - Updated ENV configs along with comments
>>>> - Restructured configs for more readability
>>>> - Add CONFIG_ENV_OVERWRITE
>>>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>>
>>>> Changes for v3:
>>>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>>>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>>> - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>>> - Add is_mx6dl()
>>>> - Add is_mx6solo()
>>>> - Use is_mx6dq()
>>>> - Add last commit sha1 and header in pull devicetree files from Linux
>>>>
>>>> Changes for v2:
>>>> - Make static to local iomux structure in board file
>>>> - Corrected rowaddr in mx6_ddr3_cfg
>>>> - Used imx_ddr_size
>>>> - Add FEC support and tested the same
>>>> - Add DM_GPIO, DM_MMC support
>>>> - Add pinctrl support
>>>> - Add devicetree support
>>>>
>>>> Jagan Teki (21):
>>>> serial: Kconfig: Add MXC_UART entry
>>>> thermal: Kconfig: Add IMX_THERMAL entry
>>>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>>> net: Kconfig: Add FEC_MXC entry
>>>> imx6: icorem6: Add ENET support
>>>> imx: s/docs\/README.imximage/doc\/README.imximage/g
>>>> arm: dts: Add devicetree for i.MX6DL
>>>> arm: dts: Add devicetree for i.MX6DQL
>>>> arm: dts: imx6dl: Add pinctrl defines
>>>> dt-bindings: clock: imx6qdl: Add clock defines
>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>>> imx6q: icorem6: Enable pinctrl driver
>>>> engicam: icorem6: Add DM_GPIO, DM_MMC support
>>>> arm: dts: Add devicetree for i.MX6Q
>>>> arm: dts: imx6q: Add pinctrl defines
>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>>> mtd: nand: Kconfig: Add NAND_MXS entry
>>>> imx6: icorem6: Add NAND support
>>>> imx6: icorem6: Enable MTD device support
>>>> imx6: icorem6: Add default mtd nand partition table
>>>
>>> All set now, please do apply.
>>
>> Let me know if you still find any issues, otherwise apply this.
>>
>
> Any help?
Sorry, I was last week at ELCE - I will go on with your patches (and the
other ones left pending) this week.
Regards,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-17 5:56 ` Stefano Babic
@ 2016-10-24 7:53 ` Jagan Teki
2016-10-24 8:36 ` Stefano Babic
0 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-24 7:53 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Mon, Oct 17, 2016 at 11:26 AM, Stefano Babic <sbabic@denx.de> wrote:
> Hi Jagan,
>
> On 17/10/2016 05:40, Jagan Teki wrote:
>> Hi Stefano,
>>
>> On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jteki@openedev.com> wrote:
>>> Hi Stefano,
>>>
>>> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki@gmail.com> wrote:
>>>> Hi Stefano,
>>>>
>>>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki@openedev.com> wrote:
>>>>> From: Jagan Teki <jagan@amarulasolutions.com>
>>>>>
>>>>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>>>>> and test on the respective starter kits as well.
>>>>>
>>>>> Tested both MMC and NAND boot.
>>>>>
>>>>> Changes for v7:
>>>>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>> - Rebase on u-boot-imx/master
>>>>>
>>>>> Changes for v6:
>>>>> - Rebase to u-boot-imx/master
>>>>> - Move few SPL configs to defconfigs
>>>>>
>>>>> Changes for v5:
>>>>> - Add NAND support
>>>>>
>>>>> Changes for v4:
>>>>> - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>>>> - Updated ENV configs along with comments
>>>>> - Restructured configs for more readability
>>>>> - Add CONFIG_ENV_OVERWRITE
>>>>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>>>
>>>>> Changes for v3:
>>>>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>>>>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>>>> - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>>>> - Add is_mx6dl()
>>>>> - Add is_mx6solo()
>>>>> - Use is_mx6dq()
>>>>> - Add last commit sha1 and header in pull devicetree files from Linux
>>>>>
>>>>> Changes for v2:
>>>>> - Make static to local iomux structure in board file
>>>>> - Corrected rowaddr in mx6_ddr3_cfg
>>>>> - Used imx_ddr_size
>>>>> - Add FEC support and tested the same
>>>>> - Add DM_GPIO, DM_MMC support
>>>>> - Add pinctrl support
>>>>> - Add devicetree support
>>>>>
>>>>> Jagan Teki (21):
>>>>> serial: Kconfig: Add MXC_UART entry
>>>>> thermal: Kconfig: Add IMX_THERMAL entry
>>>>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>>>> net: Kconfig: Add FEC_MXC entry
>>>>> imx6: icorem6: Add ENET support
>>>>> imx: s/docs\/README.imximage/doc\/README.imximage/g
>>>>> arm: dts: Add devicetree for i.MX6DL
>>>>> arm: dts: Add devicetree for i.MX6DQL
>>>>> arm: dts: imx6dl: Add pinctrl defines
>>>>> dt-bindings: clock: imx6qdl: Add clock defines
>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>>>> imx6q: icorem6: Enable pinctrl driver
>>>>> engicam: icorem6: Add DM_GPIO, DM_MMC support
>>>>> arm: dts: Add devicetree for i.MX6Q
>>>>> arm: dts: imx6q: Add pinctrl defines
>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>>>> mtd: nand: Kconfig: Add NAND_MXS entry
>>>>> imx6: icorem6: Add NAND support
>>>>> imx6: icorem6: Enable MTD device support
>>>>> imx6: icorem6: Add default mtd nand partition table
>>>>
>>>> All set now, please do apply.
>>>
>>> Let me know if you still find any issues, otherwise apply this.
>>>
>>
>> Any help?
>
> Sorry, I was last week at ELCE - I will go on with your patches (and the
> other ones left pending) this week.
Please apply this, I need to rebase on top of tom/master and send few
more series.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 7:53 ` Jagan Teki
@ 2016-10-24 8:36 ` Stefano Babic
2016-10-24 8:54 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Stefano Babic @ 2016-10-24 8:36 UTC (permalink / raw)
To: u-boot
On 24/10/2016 09:53, Jagan Teki wrote:
> Hi Stefano,
>
> On Mon, Oct 17, 2016 at 11:26 AM, Stefano Babic <sbabic@denx.de> wrote:
>> Hi Jagan,
>>
>> On 17/10/2016 05:40, Jagan Teki wrote:
>>> Hi Stefano,
>>>
>>> On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jteki@openedev.com> wrote:
>>>> Hi Stefano,
>>>>
>>>> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki@gmail.com> wrote:
>>>>> Hi Stefano,
>>>>>
>>>>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki@openedev.com> wrote:
>>>>>> From: Jagan Teki <jagan@amarulasolutions.com>
>>>>>>
>>>>>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>>>>>> and test on the respective starter kits as well.
>>>>>>
>>>>>> Tested both MMC and NAND boot.
>>>>>>
>>>>>> Changes for v7:
>>>>>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>> - Rebase on u-boot-imx/master
>>>>>>
>>>>>> Changes for v6:
>>>>>> - Rebase to u-boot-imx/master
>>>>>> - Move few SPL configs to defconfigs
>>>>>>
>>>>>> Changes for v5:
>>>>>> - Add NAND support
>>>>>>
>>>>>> Changes for v4:
>>>>>> - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>>>>> - Updated ENV configs along with comments
>>>>>> - Restructured configs for more readability
>>>>>> - Add CONFIG_ENV_OVERWRITE
>>>>>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>>>>
>>>>>> Changes for v3:
>>>>>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>>>>>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>>>>> - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>>>>> - Add is_mx6dl()
>>>>>> - Add is_mx6solo()
>>>>>> - Use is_mx6dq()
>>>>>> - Add last commit sha1 and header in pull devicetree files from Linux
>>>>>>
>>>>>> Changes for v2:
>>>>>> - Make static to local iomux structure in board file
>>>>>> - Corrected rowaddr in mx6_ddr3_cfg
>>>>>> - Used imx_ddr_size
>>>>>> - Add FEC support and tested the same
>>>>>> - Add DM_GPIO, DM_MMC support
>>>>>> - Add pinctrl support
>>>>>> - Add devicetree support
>>>>>>
>>>>>> Jagan Teki (21):
>>>>>> serial: Kconfig: Add MXC_UART entry
>>>>>> thermal: Kconfig: Add IMX_THERMAL entry
>>>>>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>>>>> net: Kconfig: Add FEC_MXC entry
>>>>>> imx6: icorem6: Add ENET support
>>>>>> imx: s/docs\/README.imximage/doc\/README.imximage/g
>>>>>> arm: dts: Add devicetree for i.MX6DL
>>>>>> arm: dts: Add devicetree for i.MX6DQL
>>>>>> arm: dts: imx6dl: Add pinctrl defines
>>>>>> dt-bindings: clock: imx6qdl: Add clock defines
>>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>>>>> imx6q: icorem6: Enable pinctrl driver
>>>>>> engicam: icorem6: Add DM_GPIO, DM_MMC support
>>>>>> arm: dts: Add devicetree for i.MX6Q
>>>>>> arm: dts: imx6q: Add pinctrl defines
>>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>>>>> mtd: nand: Kconfig: Add NAND_MXS entry
>>>>>> imx6: icorem6: Add NAND support
>>>>>> imx6: icorem6: Enable MTD device support
>>>>>> imx6: icorem6: Add default mtd nand partition table
>>>>>
>>>>> All set now, please do apply.
>>>>
>>>> Let me know if you still find any issues, otherwise apply this.
>>>>
>>>
>>> Any help?
>>
>> Sorry, I was last week at ELCE - I will go on with your patches (and the
>> other ones left pending) this week.
>
> Please apply this, I need to rebase on top of tom/master and send few
> more series.
>
Tried again, it does not compile clean.
drivers/mmc/fsl_esdhc.c:715:21: error: variable 'esdhc_ops' has
initializer but incomplete type
static const struct mmc_ops esdhc_ops = {
^
drivers/mmc/fsl_esdhc.c:716:2: error: unknown field 'send_cmd' specified
in initializer
.send_cmd = esdhc_send_cmd,
^
drivers/mmc/fsl_esdhc.c:716:14: warning: excess elements in struct
initializer
.send_cmd = esdhc_send_cmd,
^
drivers/mmc/fsl_esdhc.c:716:14: note: (near initialization for 'esdhc_ops')
drivers/mmc/fsl_esdhc.c:717:2: error: unknown field 'set_ios' specified
in initializer
.set_ios = esdhc_set_ios,
^
drivers/mmc/fsl_esdhc.c:717:13: warning: excess elements in struct
initializer
.set_ios = esdhc_set_ios,
^
drivers/mmc/fsl_esdhc.c:717:13: note: (near initialization for 'esdhc_ops')
drivers/mmc/fsl_esdhc.c:718:2: error: unknown field 'init' specified in
initializer
.init = esdhc_init,
^
drivers/mmc/fsl_esdhc.c:718:11: warning: excess elements in struct
initializer
.init = esdhc_init,
^
drivers/mmc/fsl_esdhc.c:718:11: note: (near initialization for 'esdhc_ops')
drivers/mmc/fsl_esdhc.c:719:2: error: unknown field 'getcd' specified in
initializer
.getcd = esdhc_getcd,
^
drivers/mmc/fsl_esdhc.c:719:12: warning: excess elements in struct
initializer
.getcd = esdhc_getcd,
^
drivers/mmc/fsl_esdhc.c:719:12: note: (near initialization for 'esdhc_ops')
Can you check it ?
Regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 8:36 ` Stefano Babic
@ 2016-10-24 8:54 ` Jagan Teki
2016-10-24 8:55 ` Jagan Teki
2016-10-24 9:05 ` Stefano Babic
0 siblings, 2 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-24 8:54 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Mon, Oct 24, 2016 at 2:06 PM, Stefano Babic <sbabic@denx.de> wrote:
> On 24/10/2016 09:53, Jagan Teki wrote:
>> Hi Stefano,
>>
>> On Mon, Oct 17, 2016 at 11:26 AM, Stefano Babic <sbabic@denx.de> wrote:
>>> Hi Jagan,
>>>
>>> On 17/10/2016 05:40, Jagan Teki wrote:
>>>> Hi Stefano,
>>>>
>>>> On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jteki@openedev.com> wrote:
>>>>> Hi Stefano,
>>>>>
>>>>> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki@gmail.com> wrote:
>>>>>> Hi Stefano,
>>>>>>
>>>>>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki@openedev.com> wrote:
>>>>>>> From: Jagan Teki <jagan@amarulasolutions.com>
>>>>>>>
>>>>>>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>>>>>>> and test on the respective starter kits as well.
>>>>>>>
>>>>>>> Tested both MMC and NAND boot.
>>>>>>>
>>>>>>> Changes for v7:
>>>>>>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>>> - Rebase on u-boot-imx/master
>>>>>>>
>>>>>>> Changes for v6:
>>>>>>> - Rebase to u-boot-imx/master
>>>>>>> - Move few SPL configs to defconfigs
>>>>>>>
>>>>>>> Changes for v5:
>>>>>>> - Add NAND support
>>>>>>>
>>>>>>> Changes for v4:
>>>>>>> - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>>>>>> - Updated ENV configs along with comments
>>>>>>> - Restructured configs for more readability
>>>>>>> - Add CONFIG_ENV_OVERWRITE
>>>>>>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>>>>>
>>>>>>> Changes for v3:
>>>>>>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>>>>>>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>>>>>> - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>>>>>> - Add is_mx6dl()
>>>>>>> - Add is_mx6solo()
>>>>>>> - Use is_mx6dq()
>>>>>>> - Add last commit sha1 and header in pull devicetree files from Linux
>>>>>>>
>>>>>>> Changes for v2:
>>>>>>> - Make static to local iomux structure in board file
>>>>>>> - Corrected rowaddr in mx6_ddr3_cfg
>>>>>>> - Used imx_ddr_size
>>>>>>> - Add FEC support and tested the same
>>>>>>> - Add DM_GPIO, DM_MMC support
>>>>>>> - Add pinctrl support
>>>>>>> - Add devicetree support
>>>>>>>
>>>>>>> Jagan Teki (21):
>>>>>>> serial: Kconfig: Add MXC_UART entry
>>>>>>> thermal: Kconfig: Add IMX_THERMAL entry
>>>>>>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>>>>>> net: Kconfig: Add FEC_MXC entry
>>>>>>> imx6: icorem6: Add ENET support
>>>>>>> imx: s/docs\/README.imximage/doc\/README.imximage/g
>>>>>>> arm: dts: Add devicetree for i.MX6DL
>>>>>>> arm: dts: Add devicetree for i.MX6DQL
>>>>>>> arm: dts: imx6dl: Add pinctrl defines
>>>>>>> dt-bindings: clock: imx6qdl: Add clock defines
>>>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>>>>>> imx6q: icorem6: Enable pinctrl driver
>>>>>>> engicam: icorem6: Add DM_GPIO, DM_MMC support
>>>>>>> arm: dts: Add devicetree for i.MX6Q
>>>>>>> arm: dts: imx6q: Add pinctrl defines
>>>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>>>>>> mtd: nand: Kconfig: Add NAND_MXS entry
>>>>>>> imx6: icorem6: Add NAND support
>>>>>>> imx6: icorem6: Enable MTD device support
>>>>>>> imx6: icorem6: Add default mtd nand partition table
>>>>>>
>>>>>> All set now, please do apply.
>>>>>
>>>>> Let me know if you still find any issues, otherwise apply this.
>>>>>
>>>>
>>>> Any help?
>>>
>>> Sorry, I was last week at ELCE - I will go on with your patches (and the
>>> other ones left pending) this week.
>>
>> Please apply this, I need to rebase on top of tom/master and send few
>> more series.
>>
>
>
> Tried again, it does not compile clean.
> drivers/mmc/fsl_esdhc.c:715:21: error: variable 'esdhc_ops' has
> initializer but incomplete type
> static const struct mmc_ops esdhc_ops = {
> ^
> drivers/mmc/fsl_esdhc.c:716:2: error: unknown field 'send_cmd' specified
> in initializer
> .send_cmd = esdhc_send_cmd,
> ^
> drivers/mmc/fsl_esdhc.c:716:14: warning: excess elements in struct
> initializer
> .send_cmd = esdhc_send_cmd,
> ^
> drivers/mmc/fsl_esdhc.c:716:14: note: (near initialization for 'esdhc_ops')
> drivers/mmc/fsl_esdhc.c:717:2: error: unknown field 'set_ios' specified
> in initializer
> .set_ios = esdhc_set_ios,
> ^
> drivers/mmc/fsl_esdhc.c:717:13: warning: excess elements in struct
> initializer
> .set_ios = esdhc_set_ios,
> ^
> drivers/mmc/fsl_esdhc.c:717:13: note: (near initialization for 'esdhc_ops')
> drivers/mmc/fsl_esdhc.c:718:2: error: unknown field 'init' specified in
> initializer
> .init = esdhc_init,
> ^
> drivers/mmc/fsl_esdhc.c:718:11: warning: excess elements in struct
> initializer
> .init = esdhc_init,
> ^
> drivers/mmc/fsl_esdhc.c:718:11: note: (near initialization for 'esdhc_ops')
> drivers/mmc/fsl_esdhc.c:719:2: error: unknown field 'getcd' specified in
> initializer
> .getcd = esdhc_getcd,
> ^
> drivers/mmc/fsl_esdhc.c:719:12: warning: excess elements in struct
> initializer
> .getcd = esdhc_getcd,
> ^
> drivers/mmc/fsl_esdhc.c:719:12: note: (near initialization for 'esdhc_ops')
>
> Can you check it ?
Did you take the v7 patches? I re-based on top of u-boot-imx/master
and it's compiled for me.
Please see this branch [1]
[1] https://mail.google.com/mail/u/1/#label/u-boot%2Fdenx/157a44636e8dc15f
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 8:54 ` Jagan Teki
@ 2016-10-24 8:55 ` Jagan Teki
2016-10-24 9:05 ` Stefano Babic
1 sibling, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-24 8:55 UTC (permalink / raw)
To: u-boot
On Mon, Oct 24, 2016 at 2:24 PM, Jagan Teki <jagan@openedev.com> wrote:
> Hi Stefano,
>
> On Mon, Oct 24, 2016 at 2:06 PM, Stefano Babic <sbabic@denx.de> wrote:
>> On 24/10/2016 09:53, Jagan Teki wrote:
>>> Hi Stefano,
>>>
>>> On Mon, Oct 17, 2016 at 11:26 AM, Stefano Babic <sbabic@denx.de> wrote:
>>>> Hi Jagan,
>>>>
>>>> On 17/10/2016 05:40, Jagan Teki wrote:
>>>>> Hi Stefano,
>>>>>
>>>>> On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jteki@openedev.com> wrote:
>>>>>> Hi Stefano,
>>>>>>
>>>>>> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki@gmail.com> wrote:
>>>>>>> Hi Stefano,
>>>>>>>
>>>>>>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki@openedev.com> wrote:
>>>>>>>> From: Jagan Teki <jagan@amarulasolutions.com>
>>>>>>>>
>>>>>>>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>>>>>>>> and test on the respective starter kits as well.
>>>>>>>>
>>>>>>>> Tested both MMC and NAND boot.
>>>>>>>>
>>>>>>>> Changes for v7:
>>>>>>>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>>>> - Rebase on u-boot-imx/master
>>>>>>>>
>>>>>>>> Changes for v6:
>>>>>>>> - Rebase to u-boot-imx/master
>>>>>>>> - Move few SPL configs to defconfigs
>>>>>>>>
>>>>>>>> Changes for v5:
>>>>>>>> - Add NAND support
>>>>>>>>
>>>>>>>> Changes for v4:
>>>>>>>> - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>>>>>>> - Updated ENV configs along with comments
>>>>>>>> - Restructured configs for more readability
>>>>>>>> - Add CONFIG_ENV_OVERWRITE
>>>>>>>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>>>>>>
>>>>>>>> Changes for v3:
>>>>>>>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>>>>>>>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>>>>>>> - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>>>>>>> - Add is_mx6dl()
>>>>>>>> - Add is_mx6solo()
>>>>>>>> - Use is_mx6dq()
>>>>>>>> - Add last commit sha1 and header in pull devicetree files from Linux
>>>>>>>>
>>>>>>>> Changes for v2:
>>>>>>>> - Make static to local iomux structure in board file
>>>>>>>> - Corrected rowaddr in mx6_ddr3_cfg
>>>>>>>> - Used imx_ddr_size
>>>>>>>> - Add FEC support and tested the same
>>>>>>>> - Add DM_GPIO, DM_MMC support
>>>>>>>> - Add pinctrl support
>>>>>>>> - Add devicetree support
>>>>>>>>
>>>>>>>> Jagan Teki (21):
>>>>>>>> serial: Kconfig: Add MXC_UART entry
>>>>>>>> thermal: Kconfig: Add IMX_THERMAL entry
>>>>>>>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>>>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>>>>>>> net: Kconfig: Add FEC_MXC entry
>>>>>>>> imx6: icorem6: Add ENET support
>>>>>>>> imx: s/docs\/README.imximage/doc\/README.imximage/g
>>>>>>>> arm: dts: Add devicetree for i.MX6DL
>>>>>>>> arm: dts: Add devicetree for i.MX6DQL
>>>>>>>> arm: dts: imx6dl: Add pinctrl defines
>>>>>>>> dt-bindings: clock: imx6qdl: Add clock defines
>>>>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>>>>>>> imx6q: icorem6: Enable pinctrl driver
>>>>>>>> engicam: icorem6: Add DM_GPIO, DM_MMC support
>>>>>>>> arm: dts: Add devicetree for i.MX6Q
>>>>>>>> arm: dts: imx6q: Add pinctrl defines
>>>>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>>>>>>> mtd: nand: Kconfig: Add NAND_MXS entry
>>>>>>>> imx6: icorem6: Add NAND support
>>>>>>>> imx6: icorem6: Enable MTD device support
>>>>>>>> imx6: icorem6: Add default mtd nand partition table
>>>>>>>
>>>>>>> All set now, please do apply.
>>>>>>
>>>>>> Let me know if you still find any issues, otherwise apply this.
>>>>>>
>>>>>
>>>>> Any help?
>>>>
>>>> Sorry, I was last week at ELCE - I will go on with your patches (and the
>>>> other ones left pending) this week.
>>>
>>> Please apply this, I need to rebase on top of tom/master and send few
>>> more series.
>>>
>>
>>
>> Tried again, it does not compile clean.
>> drivers/mmc/fsl_esdhc.c:715:21: error: variable 'esdhc_ops' has
>> initializer but incomplete type
>> static const struct mmc_ops esdhc_ops = {
>> ^
>> drivers/mmc/fsl_esdhc.c:716:2: error: unknown field 'send_cmd' specified
>> in initializer
>> .send_cmd = esdhc_send_cmd,
>> ^
>> drivers/mmc/fsl_esdhc.c:716:14: warning: excess elements in struct
>> initializer
>> .send_cmd = esdhc_send_cmd,
>> ^
>> drivers/mmc/fsl_esdhc.c:716:14: note: (near initialization for 'esdhc_ops')
>> drivers/mmc/fsl_esdhc.c:717:2: error: unknown field 'set_ios' specified
>> in initializer
>> .set_ios = esdhc_set_ios,
>> ^
>> drivers/mmc/fsl_esdhc.c:717:13: warning: excess elements in struct
>> initializer
>> .set_ios = esdhc_set_ios,
>> ^
>> drivers/mmc/fsl_esdhc.c:717:13: note: (near initialization for 'esdhc_ops')
>> drivers/mmc/fsl_esdhc.c:718:2: error: unknown field 'init' specified in
>> initializer
>> .init = esdhc_init,
>> ^
>> drivers/mmc/fsl_esdhc.c:718:11: warning: excess elements in struct
>> initializer
>> .init = esdhc_init,
>> ^
>> drivers/mmc/fsl_esdhc.c:718:11: note: (near initialization for 'esdhc_ops')
>> drivers/mmc/fsl_esdhc.c:719:2: error: unknown field 'getcd' specified in
>> initializer
>> .getcd = esdhc_getcd,
>> ^
>> drivers/mmc/fsl_esdhc.c:719:12: warning: excess elements in struct
>> initializer
>> .getcd = esdhc_getcd,
>> ^
>> drivers/mmc/fsl_esdhc.c:719:12: note: (near initialization for 'esdhc_ops')
>>
>> Can you check it ?
>
> Did you take the v7 patches? I re-based on top of u-boot-imx/master
> and it's compiled for me.
> Please see this branch [1]
>
> [1] https://mail.google.com/mail/u/1/#label/u-boot%2Fdenx/157a44636e8dc15f
Sorry wrong link, here is updated one
http://git.denx.de/?p=u-boot-spi.git;a=shortlog;h=refs/heads/engicam-working
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 8:54 ` Jagan Teki
2016-10-24 8:55 ` Jagan Teki
@ 2016-10-24 9:05 ` Stefano Babic
2016-10-24 10:16 ` Stefano Babic
1 sibling, 1 reply; 48+ messages in thread
From: Stefano Babic @ 2016-10-24 9:05 UTC (permalink / raw)
To: u-boot
On 24/10/2016 10:54, Jagan Teki wrote:
> Hi Stefano,
>
> On Mon, Oct 24, 2016 at 2:06 PM, Stefano Babic <sbabic@denx.de> wrote:
>> On 24/10/2016 09:53, Jagan Teki wrote:
>>> Hi Stefano,
>>>
>>> On Mon, Oct 17, 2016 at 11:26 AM, Stefano Babic <sbabic@denx.de> wrote:
>>>> Hi Jagan,
>>>>
>>>> On 17/10/2016 05:40, Jagan Teki wrote:
>>>>> Hi Stefano,
>>>>>
>>>>> On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jteki@openedev.com> wrote:
>>>>>> Hi Stefano,
>>>>>>
>>>>>> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.teki@gmail.com> wrote:
>>>>>>> Hi Stefano,
>>>>>>>
>>>>>>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki@openedev.com> wrote:
>>>>>>>> From: Jagan Teki <jagan@amarulasolutions.com>
>>>>>>>>
>>>>>>>> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
>>>>>>>> and test on the respective starter kits as well.
>>>>>>>>
>>>>>>>> Tested both MMC and NAND boot.
>>>>>>>>
>>>>>>>> Changes for v7:
>>>>>>>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>>>> - Rebase on u-boot-imx/master
>>>>>>>>
>>>>>>>> Changes for v6:
>>>>>>>> - Rebase to u-boot-imx/master
>>>>>>>> - Move few SPL configs to defconfigs
>>>>>>>>
>>>>>>>> Changes for v5:
>>>>>>>> - Add NAND support
>>>>>>>>
>>>>>>>> Changes for v4:
>>>>>>>> - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>>>>>>> - Updated ENV configs along with comments
>>>>>>>> - Restructured configs for more readability
>>>>>>>> - Add CONFIG_ENV_OVERWRITE
>>>>>>>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>>>>>>
>>>>>>>> Changes for v3:
>>>>>>>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
>>>>>>>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>>>>>>> - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>>>>>>> - Add is_mx6dl()
>>>>>>>> - Add is_mx6solo()
>>>>>>>> - Use is_mx6dq()
>>>>>>>> - Add last commit sha1 and header in pull devicetree files from Linux
>>>>>>>>
>>>>>>>> Changes for v2:
>>>>>>>> - Make static to local iomux structure in board file
>>>>>>>> - Corrected rowaddr in mx6_ddr3_cfg
>>>>>>>> - Used imx_ddr_size
>>>>>>>> - Add FEC support and tested the same
>>>>>>>> - Add DM_GPIO, DM_MMC support
>>>>>>>> - Add pinctrl support
>>>>>>>> - Add devicetree support
>>>>>>>>
>>>>>>>> Jagan Teki (21):
>>>>>>>> serial: Kconfig: Add MXC_UART entry
>>>>>>>> thermal: Kconfig: Add IMX_THERMAL entry
>>>>>>>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>>>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>>>>>>> net: Kconfig: Add FEC_MXC entry
>>>>>>>> imx6: icorem6: Add ENET support
>>>>>>>> imx: s/docs\/README.imximage/doc\/README.imximage/g
>>>>>>>> arm: dts: Add devicetree for i.MX6DL
>>>>>>>> arm: dts: Add devicetree for i.MX6DQL
>>>>>>>> arm: dts: imx6dl: Add pinctrl defines
>>>>>>>> dt-bindings: clock: imx6qdl: Add clock defines
>>>>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>>>>>>> imx6q: icorem6: Enable pinctrl driver
>>>>>>>> engicam: icorem6: Add DM_GPIO, DM_MMC support
>>>>>>>> arm: dts: Add devicetree for i.MX6Q
>>>>>>>> arm: dts: imx6q: Add pinctrl defines
>>>>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>>>>>>> mtd: nand: Kconfig: Add NAND_MXS entry
>>>>>>>> imx6: icorem6: Add NAND support
>>>>>>>> imx6: icorem6: Enable MTD device support
>>>>>>>> imx6: icorem6: Add default mtd nand partition table
>>>>>>>
>>>>>>> All set now, please do apply.
>>>>>>
>>>>>> Let me know if you still find any issues, otherwise apply this.
>>>>>>
>>>>>
>>>>> Any help?
>>>>
>>>> Sorry, I was last week at ELCE - I will go on with your patches (and the
>>>> other ones left pending) this week.
>>>
>>> Please apply this, I need to rebase on top of tom/master and send few
>>> more series.
>>>
>>
>>
>> Tried again, it does not compile clean.
>> drivers/mmc/fsl_esdhc.c:715:21: error: variable 'esdhc_ops' has
>> initializer but incomplete type
>> static const struct mmc_ops esdhc_ops = {
>> ^
>> drivers/mmc/fsl_esdhc.c:716:2: error: unknown field 'send_cmd' specified
>> in initializer
>> .send_cmd = esdhc_send_cmd,
>> ^
>> drivers/mmc/fsl_esdhc.c:716:14: warning: excess elements in struct
>> initializer
>> .send_cmd = esdhc_send_cmd,
>> ^
>> drivers/mmc/fsl_esdhc.c:716:14: note: (near initialization for 'esdhc_ops')
>> drivers/mmc/fsl_esdhc.c:717:2: error: unknown field 'set_ios' specified
>> in initializer
>> .set_ios = esdhc_set_ios,
>> ^
>> drivers/mmc/fsl_esdhc.c:717:13: warning: excess elements in struct
>> initializer
>> .set_ios = esdhc_set_ios,
>> ^
>> drivers/mmc/fsl_esdhc.c:717:13: note: (near initialization for 'esdhc_ops')
>> drivers/mmc/fsl_esdhc.c:718:2: error: unknown field 'init' specified in
>> initializer
>> .init = esdhc_init,
>> ^
>> drivers/mmc/fsl_esdhc.c:718:11: warning: excess elements in struct
>> initializer
>> .init = esdhc_init,
>> ^
>> drivers/mmc/fsl_esdhc.c:718:11: note: (near initialization for 'esdhc_ops')
>> drivers/mmc/fsl_esdhc.c:719:2: error: unknown field 'getcd' specified in
>> initializer
>> .getcd = esdhc_getcd,
>> ^
>> drivers/mmc/fsl_esdhc.c:719:12: warning: excess elements in struct
>> initializer
>> .getcd = esdhc_getcd,
>> ^
>> drivers/mmc/fsl_esdhc.c:719:12: note: (near initialization for 'esdhc_ops')
>>
>> Can you check it ?
>
> Did you take the v7 patches? I re-based on top of u-boot-imx/master
> and it's compiled for me.
I take the v7:
http://patchwork.ozlabs.org/bundle/sbabic/jagan/
Applied on top of u-boot-imx master, I get the error. There are just a
few of new patches on the tree, I doubt that are guilty for it.
> Please see this branch [1]
>
> [1] https://mail.google.com/mail/u/1/#label/u-boot%2Fdenx/157a44636e8dc15f
>
This linkj does not work - anyway, I should pick up just patches that
are in patchwork.
Regards,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 9:05 ` Stefano Babic
@ 2016-10-24 10:16 ` Stefano Babic
2016-10-24 10:23 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Stefano Babic @ 2016-10-24 10:16 UTC (permalink / raw)
To: u-boot
Hi Jagan, Peng,
On 24/10/2016 11:05, Stefano Babic wrote:
>> Did you take the v7 patches? I re-based on top of u-boot-imx/master
>> and it's compiled for me.
>
> I take the v7:
>
> http://patchwork.ozlabs.org/bundle/sbabic/jagan/
>
> Applied on top of u-boot-imx master, I get the error. There are just a
> few of new patches on the tree, I doubt that are guilty for it.
>
I got the same issue for mx6ull_14x14_evk_plugin after applying Peng's
patches for plugins. Issue is raised in fsl_esdhc.c driver, that should
be not yet prepared for DM_MMC_OPS.
Is there a missing patch ? Could you take a look ?
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 10:16 ` Stefano Babic
@ 2016-10-24 10:23 ` Jagan Teki
2016-10-24 10:48 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-24 10:23 UTC (permalink / raw)
To: u-boot
+ Peng
On Mon, Oct 24, 2016 at 3:46 PM, Stefano Babic <sbabic@denx.de> wrote:
> Hi Jagan, Peng,
>
> On 24/10/2016 11:05, Stefano Babic wrote:
>
>>> Did you take the v7 patches? I re-based on top of u-boot-imx/master
>>> and it's compiled for me.
>>
>> I take the v7:
>>
>> http://patchwork.ozlabs.org/bundle/sbabic/jagan/
>>
>> Applied on top of u-boot-imx master, I get the error. There are just a
>> few of new patches on the tree, I doubt that are guilty for it.
>>
>
> I got the same issue for mx6ull_14x14_evk_plugin after applying Peng's
> patches for plugins. Issue is raised in fsl_esdhc.c driver, that should
> be not yet prepared for DM_MMC_OPS.
>
> Is there a missing patch ? Could you take a look ?
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 10:23 ` Jagan Teki
@ 2016-10-24 10:48 ` Jagan Teki
2016-10-24 11:03 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-24 10:48 UTC (permalink / raw)
To: u-boot
On Mon, Oct 24, 2016 at 3:53 PM, Jagan Teki <jagan@openedev.com> wrote:
> + Peng
>
> On Mon, Oct 24, 2016 at 3:46 PM, Stefano Babic <sbabic@denx.de> wrote:
>> Hi Jagan, Peng,
>>
>> On 24/10/2016 11:05, Stefano Babic wrote:
>>
>>>> Did you take the v7 patches? I re-based on top of u-boot-imx/master
>>>> and it's compiled for me.
>>>
>>> I take the v7:
>>>
>>> http://patchwork.ozlabs.org/bundle/sbabic/jagan/
>>>
>>> Applied on top of u-boot-imx master, I get the error. There are just a
>>> few of new patches on the tree, I doubt that are guilty for it.
>>>
>>
>> I got the same issue for mx6ull_14x14_evk_plugin after applying Peng's
>> patches for plugins. Issue is raised in fsl_esdhc.c driver, that should
>> be not yet prepared for DM_MMC_OPS.
>>
>> Is there a missing patch ? Could you take a look ?
Got the issue, we need to update 2 recent changes from Simon
patches[1][2] I will fix and update.
[1] http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commitdiff;h=896a74f615d6ffcbbcbec1505b19ed3280fe7873
[2] http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commitdiff;h=252788b4eda852e0195e1903e55480b4bf4fea9d
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 10:48 ` Jagan Teki
@ 2016-10-24 11:03 ` Jagan Teki
2016-10-24 11:35 ` Stefano Babic
0 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-24 11:03 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Mon, Oct 24, 2016 at 4:18 PM, Jagan Teki <jagan@openedev.com> wrote:
> On Mon, Oct 24, 2016 at 3:53 PM, Jagan Teki <jagan@openedev.com> wrote:
>> + Peng
>>
>> On Mon, Oct 24, 2016 at 3:46 PM, Stefano Babic <sbabic@denx.de> wrote:
>>> Hi Jagan, Peng,
>>>
>>> On 24/10/2016 11:05, Stefano Babic wrote:
>>>
>>>>> Did you take the v7 patches? I re-based on top of u-boot-imx/master
>>>>> and it's compiled for me.
>>>>
>>>> I take the v7:
>>>>
>>>> http://patchwork.ozlabs.org/bundle/sbabic/jagan/
>>>>
>>>> Applied on top of u-boot-imx master, I get the error. There are just a
>>>> few of new patches on the tree, I doubt that are guilty for it.
>>>>
>>>
>>> I got the same issue for mx6ull_14x14_evk_plugin after applying Peng's
>>> patches for plugins. Issue is raised in fsl_esdhc.c driver, that should
>>> be not yet prepared for DM_MMC_OPS.
>>>
>>> Is there a missing patch ? Could you take a look ?
>
> Got the issue, we need to update 2 recent changes from Simon
> patches[1][2] I will fix and update.
>
> [1] http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commitdiff;h=896a74f615d6ffcbbcbec1505b19ed3280fe7873
> [2] http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commitdiff;h=252788b4eda852e0195e1903e55480b4bf4fea9d
Please try this patches, I've updated the above changes.
[1] http://git.denx.de/?p=u-boot-spi.git;a=shortlog;h=refs/heads/engicam-working
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 11:03 ` Jagan Teki
@ 2016-10-24 11:35 ` Stefano Babic
2016-10-24 11:46 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Stefano Babic @ 2016-10-24 11:35 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On 24/10/2016 13:03, Jagan Teki wrote:
> Hi Stefano,
>
> On Mon, Oct 24, 2016 at 4:18 PM, Jagan Teki <jagan@openedev.com> wrote:
>> On Mon, Oct 24, 2016 at 3:53 PM, Jagan Teki <jagan@openedev.com> wrote:
>>> + Peng
>>>
>>> On Mon, Oct 24, 2016 at 3:46 PM, Stefano Babic <sbabic@denx.de> wrote:
>>>> Hi Jagan, Peng,
>>>>
>>>> On 24/10/2016 11:05, Stefano Babic wrote:
>>>>
>>>>>> Did you take the v7 patches? I re-based on top of u-boot-imx/master
>>>>>> and it's compiled for me.
>>>>>
>>>>> I take the v7:
>>>>>
>>>>> http://patchwork.ozlabs.org/bundle/sbabic/jagan/
>>>>>
>>>>> Applied on top of u-boot-imx master, I get the error. There are just a
>>>>> few of new patches on the tree, I doubt that are guilty for it.
>>>>>
>>>>
>>>> I got the same issue for mx6ull_14x14_evk_plugin after applying Peng's
>>>> patches for plugins. Issue is raised in fsl_esdhc.c driver, that should
>>>> be not yet prepared for DM_MMC_OPS.
>>>>
>>>> Is there a missing patch ? Could you take a look ?
>>
>> Got the issue, we need to update 2 recent changes from Simon
>> patches[1][2] I will fix and update.
>>
>> [1] http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commitdiff;h=896a74f615d6ffcbbcbec1505b19ed3280fe7873
>> [2] http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commitdiff;h=252788b4eda852e0195e1903e55480b4bf4fea9d
>
> Please try this patches, I've updated the above changes.
>
> [1] http://git.denx.de/?p=u-boot-spi.git;a=shortlog;h=refs/heads/engicam-working
>
No, this is not the correct way to do. We should stick with the patches
sent to ML and included in patchworks. They are documented and I cannot
(that means, all custodians are not allowed) to simply pick up patches
from somewhere else.
It is enough that we agree about issue and solution. I had already
tested with the following patch:
diff --git a/configs/imx6qdl_icore_mmc_defconfig
b/configs/imx6qdl_icore_mmc_defconfig
index 221ea7e..c947e10 100644
--- a/configs/imx6qdl_icore_mmc_defconfig
+++ b/configs/imx6qdl_icore_mmc_defconfig
@@ -6,6 +6,8 @@ CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
CONFIG_SYS_PROMPT="icorem6qdl> "
CONFIG_SPL=y
+# CONFIG_BLK is not set
+# CONFIG_DM_MMC_OPS is not set
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_DISPLAY_CPUINFO=y
diff --git a/configs/imx6qdl_icore_nand_defconfig
b/configs/imx6qdl_icore_nand_defconfig
index 8ac3099..55650bb 100644
--- a/configs/imx6qdl_icore_nand_defconfig
+++ b/configs/imx6qdl_icore_nand_defconfig
@@ -6,6 +6,8 @@ CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
CONFIG_SYS_PROMPT="icorem6qdl> "
CONFIG_SPL=y
+# CONFIG_BLK is not set
+# CONFIG_DM_MMC_OPS is not set
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_DISPLAY_CPUINFO=y
This solves the issue and your boards are built, but I won't apply it
without discussing with you. I could also apply this directly to patch
4/21 where it belongs, if you agree, without you have to post it again
(of course you can post it again, but I am fine also if I fix by
applying). What do you mean ?
Best regards,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 11:35 ` Stefano Babic
@ 2016-10-24 11:46 ` Jagan Teki
2016-10-24 12:01 ` Stefano Babic
0 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-24 11:46 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Mon, Oct 24, 2016 at 5:05 PM, Stefano Babic <sbabic@denx.de> wrote:
> Hi Jagan,
>
> On 24/10/2016 13:03, Jagan Teki wrote:
>> Hi Stefano,
>>
>> On Mon, Oct 24, 2016 at 4:18 PM, Jagan Teki <jagan@openedev.com> wrote:
>>> On Mon, Oct 24, 2016 at 3:53 PM, Jagan Teki <jagan@openedev.com> wrote:
>>>> + Peng
>>>>
>>>> On Mon, Oct 24, 2016 at 3:46 PM, Stefano Babic <sbabic@denx.de> wrote:
>>>>> Hi Jagan, Peng,
>>>>>
>>>>> On 24/10/2016 11:05, Stefano Babic wrote:
>>>>>
>>>>>>> Did you take the v7 patches? I re-based on top of u-boot-imx/master
>>>>>>> and it's compiled for me.
>>>>>>
>>>>>> I take the v7:
>>>>>>
>>>>>> http://patchwork.ozlabs.org/bundle/sbabic/jagan/
>>>>>>
>>>>>> Applied on top of u-boot-imx master, I get the error. There are just a
>>>>>> few of new patches on the tree, I doubt that are guilty for it.
>>>>>>
>>>>>
>>>>> I got the same issue for mx6ull_14x14_evk_plugin after applying Peng's
>>>>> patches for plugins. Issue is raised in fsl_esdhc.c driver, that should
>>>>> be not yet prepared for DM_MMC_OPS.
>>>>>
>>>>> Is there a missing patch ? Could you take a look ?
>>>
>>> Got the issue, we need to update 2 recent changes from Simon
>>> patches[1][2] I will fix and update.
>>>
>>> [1] http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commitdiff;h=896a74f615d6ffcbbcbec1505b19ed3280fe7873
>>> [2] http://git.denx.de/?p=u-boot/u-boot-imx.git;a=commitdiff;h=252788b4eda852e0195e1903e55480b4bf4fea9d
>>
>> Please try this patches, I've updated the above changes.
>>
>> [1] http://git.denx.de/?p=u-boot-spi.git;a=shortlog;h=refs/heads/engicam-working
>>
>
> No, this is not the correct way to do. We should stick with the patches
> sent to ML and included in patchworks. They are documented and I cannot
> (that means, all custodians are not allowed) to simply pick up patches
> from somewhere else.
True, but I am not saying you to just apply the branch. My intention
was to check the new changes from your side so-that will send the
series to ML again.
>
> It is enough that we agree about issue and solution. I had already
> tested with the following patch:
>
> diff --git a/configs/imx6qdl_icore_mmc_defconfig
> b/configs/imx6qdl_icore_mmc_defconfig
> index 221ea7e..c947e10 100644
> --- a/configs/imx6qdl_icore_mmc_defconfig
> +++ b/configs/imx6qdl_icore_mmc_defconfig
> @@ -6,6 +6,8 @@ CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
> CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
> CONFIG_SYS_PROMPT="icorem6qdl> "
> CONFIG_SPL=y
> +# CONFIG_BLK is not set
> +# CONFIG_DM_MMC_OPS is not set
> CONFIG_BOOTDELAY=3
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_DISPLAY_CPUINFO=y
> diff --git a/configs/imx6qdl_icore_nand_defconfig
nand_defconfig doesn't require this change.
> b/configs/imx6qdl_icore_nand_defconfig
> index 8ac3099..55650bb 100644
> --- a/configs/imx6qdl_icore_nand_defconfig
> +++ b/configs/imx6qdl_icore_nand_defconfig
> @@ -6,6 +6,8 @@ CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
> CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
> CONFIG_SYS_PROMPT="icorem6qdl> "
> CONFIG_SPL=y
> +# CONFIG_BLK is not set
> +# CONFIG_DM_MMC_OPS is not set
> CONFIG_BOOTDELAY=3
> CONFIG_BOARD_EARLY_INIT_F=y
> CONFIG_DISPLAY_CPUINFO=y
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 11:46 ` Jagan Teki
@ 2016-10-24 12:01 ` Stefano Babic
2016-10-24 12:09 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Stefano Babic @ 2016-10-24 12:01 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On 24/10/2016 13:46, Jagan Teki wrote:
>>
>> No, this is not the correct way to do. We should stick with the patches
>> sent to ML and included in patchworks. They are documented and I cannot
>> (that means, all custodians are not allowed) to simply pick up patches
>> from somewhere else.
>
> True, but I am not saying you to just apply the branch. My intention
> was to check the new changes from your side so-that will send the
> series to ML again.
ok
>
>>
>> It is enough that we agree about issue and solution. I had already
>> tested with the following patch:
>>
>> diff --git a/configs/imx6qdl_icore_mmc_defconfig
>> b/configs/imx6qdl_icore_mmc_defconfig
>> index 221ea7e..c947e10 100644
>> --- a/configs/imx6qdl_icore_mmc_defconfig
>> +++ b/configs/imx6qdl_icore_mmc_defconfig
>> @@ -6,6 +6,8 @@ CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
>> CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
>> CONFIG_SYS_PROMPT="icorem6qdl> "
>> CONFIG_SPL=y
>> +# CONFIG_BLK is not set
>> +# CONFIG_DM_MMC_OPS is not set
>> CONFIG_BOOTDELAY=3
>> CONFIG_BOARD_EARLY_INIT_F=y
>> CONFIG_DISPLAY_CPUINFO=y
>> diff --git a/configs/imx6qdl_icore_nand_defconfig
>
> nand_defconfig doesn't require this change.
>
It is what I had expected, but fsl_esdhc is built even in the NAND
configuration. There is omething else enabling (not in defconfig).
In fact, dropping the two lines, I get the error again for
imx6qdl_icore_nand.
The reason is that even if MMC is not set, as far I can see, these are
automatically set:
CONFIG_DM_MMC=y
CONFIG_DM_MMC_OPS=y
>> b/configs/imx6qdl_icore_nand_defconfig
>> index 8ac3099..55650bb 100644
>> --- a/configs/imx6qdl_icore_nand_defconfig
>> +++ b/configs/imx6qdl_icore_nand_defconfig
>> @@ -6,6 +6,8 @@ CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
>> CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
>> CONFIG_SYS_PROMPT="icorem6qdl> "
>> CONFIG_SPL=y
>> +# CONFIG_BLK is not set
>> +# CONFIG_DM_MMC_OPS is not set
>> CONFIG_BOOTDELAY=3
>> CONFIG_BOARD_EARLY_INIT_F=y
>> CONFIG_DISPLAY_CPUINFO=y
>
> thanks!
>
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 12:01 ` Stefano Babic
@ 2016-10-24 12:09 ` Jagan Teki
2016-10-24 12:34 ` Stefano Babic
0 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-24 12:09 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Mon, Oct 24, 2016 at 5:31 PM, Stefano Babic <sbabic@denx.de> wrote:
> Hi Jagan,
>
> On 24/10/2016 13:46, Jagan Teki wrote:
>
>>>
>>> No, this is not the correct way to do. We should stick with the patches
>>> sent to ML and included in patchworks. They are documented and I cannot
>>> (that means, all custodians are not allowed) to simply pick up patches
>>> from somewhere else.
>>
>> True, but I am not saying you to just apply the branch. My intention
>> was to check the new changes from your side so-that will send the
>> series to ML again.
>
> ok
>
>>
>>>
>>> It is enough that we agree about issue and solution. I had already
>>> tested with the following patch:
>>>
>>> diff --git a/configs/imx6qdl_icore_mmc_defconfig
>>> b/configs/imx6qdl_icore_mmc_defconfig
>>> index 221ea7e..c947e10 100644
>>> --- a/configs/imx6qdl_icore_mmc_defconfig
>>> +++ b/configs/imx6qdl_icore_mmc_defconfig
>>> @@ -6,6 +6,8 @@ CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
>>> CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
>>> CONFIG_SYS_PROMPT="icorem6qdl> "
>>> CONFIG_SPL=y
>>> +# CONFIG_BLK is not set
>>> +# CONFIG_DM_MMC_OPS is not set
>>> CONFIG_BOOTDELAY=3
>>> CONFIG_BOARD_EARLY_INIT_F=y
>>> CONFIG_DISPLAY_CPUINFO=y
>>> diff --git a/configs/imx6qdl_icore_nand_defconfig
>>
>> nand_defconfig doesn't require this change.
>>
>
> It is what I had expected, but fsl_esdhc is built even in the NAND
> configuration. There is omething else enabling (not in defconfig).
>
> In fact, dropping the two lines, I get the error again for
> imx6qdl_icore_nand.
>
> The reason is that even if MMC is not set, as far I can see, these are
> automatically set:
>
> CONFIG_DM_MMC=y
> CONFIG_DM_MMC_OPS=y
Ohh, Ok, This is because mx6_common.h by default enabling the MMC.
So I will update these on nand support patch[1] and send the single
patch, is that OK?
[1] [PATCH v8 21/23] imx6: icorem6: Add NAND support
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 12:09 ` Jagan Teki
@ 2016-10-24 12:34 ` Stefano Babic
2016-10-24 13:15 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Stefano Babic @ 2016-10-24 12:34 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On 24/10/2016 14:09, Jagan Teki wrote:
> Hi Stefano,
>
> On Mon, Oct 24, 2016 at 5:31 PM, Stefano Babic <sbabic@denx.de> wrote:
>> Hi Jagan,
>>
>> On 24/10/2016 13:46, Jagan Teki wrote:
>>
>>>>
>>>> No, this is not the correct way to do. We should stick with the patches
>>>> sent to ML and included in patchworks. They are documented and I cannot
>>>> (that means, all custodians are not allowed) to simply pick up patches
>>>> from somewhere else.
>>>
>>> True, but I am not saying you to just apply the branch. My intention
>>> was to check the new changes from your side so-that will send the
>>> series to ML again.
>>
>> ok
>>
>>>
>>>>
>>>> It is enough that we agree about issue and solution. I had already
>>>> tested with the following patch:
>>>>
>>>> diff --git a/configs/imx6qdl_icore_mmc_defconfig
>>>> b/configs/imx6qdl_icore_mmc_defconfig
>>>> index 221ea7e..c947e10 100644
>>>> --- a/configs/imx6qdl_icore_mmc_defconfig
>>>> +++ b/configs/imx6qdl_icore_mmc_defconfig
>>>> @@ -6,6 +6,8 @@ CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
>>>> CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
>>>> CONFIG_SYS_PROMPT="icorem6qdl> "
>>>> CONFIG_SPL=y
>>>> +# CONFIG_BLK is not set
>>>> +# CONFIG_DM_MMC_OPS is not set
>>>> CONFIG_BOOTDELAY=3
>>>> CONFIG_BOARD_EARLY_INIT_F=y
>>>> CONFIG_DISPLAY_CPUINFO=y
>>>> diff --git a/configs/imx6qdl_icore_nand_defconfig
>>>
>>> nand_defconfig doesn't require this change.
>>>
>>
>> It is what I had expected, but fsl_esdhc is built even in the NAND
>> configuration. There is omething else enabling (not in defconfig).
>>
>> In fact, dropping the two lines, I get the error again for
>> imx6qdl_icore_nand.
>>
>> The reason is that even if MMC is not set, as far I can see, these are
>> automatically set:
>>
>> CONFIG_DM_MMC=y
>> CONFIG_DM_MMC_OPS=y
>
> Ohh, Ok, This is because mx6_common.h by default enabling the MMC.
Right.
> So I will update these on nand support patch[1] and send the single
> patch, is that OK?
>
> [1] [PATCH v8 21/23] imx6: icorem6: Add NAND support
>
Please wait, I am confused. You have sent a complete V8, but as far as I
understand the oinly changes are reported above (Patch 14/15).
However, even if I have not tested, this would break bisecting, because
patch 4/23 introduces the board and building with that commit leads to
the error. So changes should be respective in patch 4 for mmc and patch
21 for NAND taking as reference V8.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 12:34 ` Stefano Babic
@ 2016-10-24 13:15 ` Jagan Teki
2016-10-24 14:01 ` Stefano Babic
0 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-24 13:15 UTC (permalink / raw)
To: u-boot
On Mon, Oct 24, 2016 at 6:04 PM, Stefano Babic <sbabic@denx.de> wrote:
> Hi Jagan,
>
> On 24/10/2016 14:09, Jagan Teki wrote:
>> Hi Stefano,
>>
>> On Mon, Oct 24, 2016 at 5:31 PM, Stefano Babic <sbabic@denx.de> wrote:
>>> Hi Jagan,
>>>
>>> On 24/10/2016 13:46, Jagan Teki wrote:
>>>
>>>>>
>>>>> No, this is not the correct way to do. We should stick with the patches
>>>>> sent to ML and included in patchworks. They are documented and I cannot
>>>>> (that means, all custodians are not allowed) to simply pick up patches
>>>>> from somewhere else.
>>>>
>>>> True, but I am not saying you to just apply the branch. My intention
>>>> was to check the new changes from your side so-that will send the
>>>> series to ML again.
>>>
>>> ok
>>>
>>>>
>>>>>
>>>>> It is enough that we agree about issue and solution. I had already
>>>>> tested with the following patch:
>>>>>
>>>>> diff --git a/configs/imx6qdl_icore_mmc_defconfig
>>>>> b/configs/imx6qdl_icore_mmc_defconfig
>>>>> index 221ea7e..c947e10 100644
>>>>> --- a/configs/imx6qdl_icore_mmc_defconfig
>>>>> +++ b/configs/imx6qdl_icore_mmc_defconfig
>>>>> @@ -6,6 +6,8 @@ CONFIG_DEFAULT_FDT_FILE="imx6dl-icore.dtb"
>>>>> CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore"
>>>>> CONFIG_SYS_PROMPT="icorem6qdl> "
>>>>> CONFIG_SPL=y
>>>>> +# CONFIG_BLK is not set
>>>>> +# CONFIG_DM_MMC_OPS is not set
>>>>> CONFIG_BOOTDELAY=3
>>>>> CONFIG_BOARD_EARLY_INIT_F=y
>>>>> CONFIG_DISPLAY_CPUINFO=y
>>>>> diff --git a/configs/imx6qdl_icore_nand_defconfig
>>>>
>>>> nand_defconfig doesn't require this change.
>>>>
>>>
>>> It is what I had expected, but fsl_esdhc is built even in the NAND
>>> configuration. There is omething else enabling (not in defconfig).
>>>
>>> In fact, dropping the two lines, I get the error again for
>>> imx6qdl_icore_nand.
>>>
>>> The reason is that even if MMC is not set, as far I can see, these are
>>> automatically set:
>>>
>>> CONFIG_DM_MMC=y
>>> CONFIG_DM_MMC_OPS=y
>>
>> Ohh, Ok, This is because mx6_common.h by default enabling the MMC.
>
> Right.
>
>> So I will update these on nand support patch[1] and send the single
>> patch, is that OK?
>>
>> [1] [PATCH v8 21/23] imx6: icorem6: Add NAND support
>>
>
> Please wait, I am confused. You have sent a complete V8, but as far as I
> understand the oinly changes are reported above (Patch 14/15).
>
> However, even if I have not tested, this would break bisecting, because
> patch 4/23 introduces the board and building with that commit leads to
> the error. So changes should be respective in patch 4 for mmc and patch
> 21 for NAND taking as reference V8.
Yes, I've added 14/23 and 15/23 for new changes so the previous 14/21
becomes 16/23 now and the only missing one is 21/23. So I will update
this 21/23 for v9. Hope this make clear for you.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 13:15 ` Jagan Teki
@ 2016-10-24 14:01 ` Stefano Babic
2016-10-24 14:21 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Stefano Babic @ 2016-10-24 14:01 UTC (permalink / raw)
To: u-boot
On 24/10/2016 15:15, Jagan Teki wrote:
> On Mon, Oct 24, 2016 at 6:04 PM, Stefano Babic <sbabic@denx.de> wrote:
>> Hi Jagan,
>>
>> Please wait, I am confused. You have sent a complete V8, but as far as I
>> understand the oinly changes are reported above (Patch 14/15).
>>
>> However, even if I have not tested, this would break bisecting, because
>> patch 4/23 introduces the board and building with that commit leads to
>> the error. So changes should be respective in patch 4 for mmc and patch
>> 21 for NAND taking as reference V8.
>
> Yes, I've added 14/23 and 15/23 for new changes so the previous 14/21
> becomes 16/23 now and the only missing one is 21/23. So I will update
> this 21/23 for v9. Hope this make clear for you.
It is ok if you feel better to send V9 - what I meant it is just that
entries for CONFIG_DM_MM and CONFIG_DM_MMC_OPS should be done in the
same patch where the defconfig is added to avoid breaking bisecting.
Regards,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 14:01 ` Stefano Babic
@ 2016-10-24 14:21 ` Jagan Teki
2016-10-25 10:08 ` Jagan Teki
0 siblings, 1 reply; 48+ messages in thread
From: Jagan Teki @ 2016-10-24 14:21 UTC (permalink / raw)
To: u-boot
On Mon, Oct 24, 2016 at 7:31 PM, Stefano Babic <sbabic@denx.de> wrote:
> On 24/10/2016 15:15, Jagan Teki wrote:
>> On Mon, Oct 24, 2016 at 6:04 PM, Stefano Babic <sbabic@denx.de> wrote:
>>> Hi Jagan,
>
>>>
>>> Please wait, I am confused. You have sent a complete V8, but as far as I
>>> understand the oinly changes are reported above (Patch 14/15).
>>>
>>> However, even if I have not tested, this would break bisecting, because
>>> patch 4/23 introduces the board and building with that commit leads to
>>> the error. So changes should be respective in patch 4 for mmc and patch
>>> 21 for NAND taking as reference V8.
>>
>> Yes, I've added 14/23 and 15/23 for new changes so the previous 14/21
>> becomes 16/23 now and the only missing one is 21/23. So I will update
>> this 21/23 for v9. Hope this make clear for you.
>
> It is ok if you feel better to send V9 - what I meant it is just that
> entries for CONFIG_DM_MM and CONFIG_DM_MMC_OPS should be done in the
> same patch where the defconfig is added to avoid breaking bisecting.
OK, then I will send the 14/23 with squash of 14/23 and 15/23 to 16/23
and 21/23 v9.
Does it fine?
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
* [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
2016-10-24 14:21 ` Jagan Teki
@ 2016-10-25 10:08 ` Jagan Teki
0 siblings, 0 replies; 48+ messages in thread
From: Jagan Teki @ 2016-10-25 10:08 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Mon, Oct 24, 2016 at 7:51 PM, Jagan Teki <jagan@openedev.com> wrote:
> On Mon, Oct 24, 2016 at 7:31 PM, Stefano Babic <sbabic@denx.de> wrote:
>> On 24/10/2016 15:15, Jagan Teki wrote:
>>> On Mon, Oct 24, 2016 at 6:04 PM, Stefano Babic <sbabic@denx.de> wrote:
>>>> Hi Jagan,
>>
>>>>
>>>> Please wait, I am confused. You have sent a complete V8, but as far as I
>>>> understand the oinly changes are reported above (Patch 14/15).
>>>>
>>>> However, even if I have not tested, this would break bisecting, because
>>>> patch 4/23 introduces the board and building with that commit leads to
>>>> the error. So changes should be respective in patch 4 for mmc and patch
>>>> 21 for NAND taking as reference V8.
>>>
>>> Yes, I've added 14/23 and 15/23 for new changes so the previous 14/21
>>> becomes 16/23 now and the only missing one is 21/23. So I will update
>>> this 21/23 for v9. Hope this make clear for you.
>>
>> It is ok if you feel better to send V9 - what I meant it is just that
>> entries for CONFIG_DM_MM and CONFIG_DM_MMC_OPS should be done in the
>> same patch where the defconfig is added to avoid breaking bisecting.
>
> OK, then I will send the 14/23 with squash of 14/23 and 15/23 to 16/23
> and 21/23 v9.
> Does it fine?
Sent these two patches with v9, please let me know for any issues.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 48+ messages in thread
end of thread, other threads:[~2016-10-25 10:08 UTC | newest]
Thread overview: 48+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-10-08 12:30 [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 01/21] serial: Kconfig: Add MXC_UART entry Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 02/21] thermal: Kconfig: Add IMX_THERMAL entry Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 03/21] config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 04/21] arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 05/21] net: Kconfig: Add FEC_MXC entry Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 06/21] imx6: icorem6: Add ENET support Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 07/21] imx: s/docs\/README.imximage/doc\/README.imximage/g Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 08/21] arm: dts: Add devicetree for i.MX6DL Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 09/21] arm: dts: Add devicetree for i.MX6DQL Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 10/21] arm: dts: imx6dl: Add pinctrl defines Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 11/21] dt-bindings: clock: imx6qdl: Add clock defines Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 12/21] arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 13/21] imx6q: icorem6: Enable pinctrl driver Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 14/21] engicam: icorem6: Add DM_GPIO, DM_MMC support Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 15/21] arm: dts: Add devicetree for i.MX6Q Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 16/21] arm: dts: imx6q: Add pinctrl defines Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 17/21] arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 18/21] mtd: nand: Kconfig: Add NAND_MXS entry Jagan Teki
2016-10-11 22:10 ` Jörg Krause
2016-10-11 22:24 ` Sergey Kubushyn
2016-10-12 5:50 ` Jagan Teki
2016-10-12 6:19 ` Jörg Krause
2016-10-08 12:30 ` [U-Boot] [PATCH v7 19/21] imx6: icorem6: Add NAND support Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 20/21] imx6: icorem6: Enable MTD device support Jagan Teki
2016-10-08 12:30 ` [U-Boot] [PATCH v7 21/21] imx6: icorem6: Add default mtd nand partition table Jagan Teki
2016-10-09 14:45 ` [U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support Jagan Teki
2016-10-11 3:30 ` Jagan Teki
2016-10-17 3:40 ` Jagan Teki
2016-10-17 5:56 ` Stefano Babic
2016-10-24 7:53 ` Jagan Teki
2016-10-24 8:36 ` Stefano Babic
2016-10-24 8:54 ` Jagan Teki
2016-10-24 8:55 ` Jagan Teki
2016-10-24 9:05 ` Stefano Babic
2016-10-24 10:16 ` Stefano Babic
2016-10-24 10:23 ` Jagan Teki
2016-10-24 10:48 ` Jagan Teki
2016-10-24 11:03 ` Jagan Teki
2016-10-24 11:35 ` Stefano Babic
2016-10-24 11:46 ` Jagan Teki
2016-10-24 12:01 ` Stefano Babic
2016-10-24 12:09 ` Jagan Teki
2016-10-24 12:34 ` Stefano Babic
2016-10-24 13:15 ` Jagan Teki
2016-10-24 14:01 ` Stefano Babic
2016-10-24 14:21 ` Jagan Teki
2016-10-25 10:08 ` Jagan Teki
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.