* [PATCH v2 1/3] cyrus: Add poweroff/reset support
@ 2016-10-23 23:48 Andy Fleming
2016-10-23 23:48 ` [PATCH 2/3] 85xx: Enable gpio power/reset driver Andy Fleming
` (2 more replies)
0 siblings, 3 replies; 7+ messages in thread
From: Andy Fleming @ 2016-10-23 23:48 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: aperez
Cyrus uses GPIOs to complete board shutdown/reset.
Add nodes to indicate that support to the device tree.
Signed-off-by: Andy Fleming <afleming@gmail.com>
---
v2: No changes
arch/powerpc/boot/dts/fsl/cyrus_p5020.dts | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/powerpc/boot/dts/fsl/cyrus_p5020.dts b/arch/powerpc/boot/dts/fsl/cyrus_p5020.dts
index c603390..e417aaa 100644
--- a/arch/powerpc/boot/dts/fsl/cyrus_p5020.dts
+++ b/arch/powerpc/boot/dts/fsl/cyrus_p5020.dts
@@ -150,6 +150,17 @@
0 0x00010000>;
};
};
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio0 3 1>;
+ };
+
+ gpio-restart {
+ compatible = "gpio-restart";
+ gpios = <&gpio0 2 1>;
+ };
+
};
/include/ "p5020si-post.dtsi"
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 2/3] 85xx: Enable gpio power/reset driver
2016-10-23 23:48 [PATCH v2 1/3] cyrus: Add poweroff/reset support Andy Fleming
@ 2016-10-23 23:48 ` Andy Fleming
2016-10-24 16:16 ` Cyrus_5040.dts Misisng luigi burdo
2017-07-05 15:37 ` 85xx: Enable gpio power/reset driver Darren Stevens
2016-10-23 23:48 ` [PATCH 3/3] corenet: Switch to of_platform_default_populate Andy Fleming
2016-11-23 7:00 ` [v2,1/3] cyrus: Add poweroff/reset support Scott Wood
2 siblings, 2 replies; 7+ messages in thread
From: Andy Fleming @ 2016-10-23 23:48 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: aperez
These config changes build:
drivers/power/reset/gpio-poweroff.c
drivers/power/reset/gpio-restart.c
Signed-off-by: Andy Fleming <afleming@gmail.com>
---
arch/powerpc/configs/fsl-emb-nonhw.config | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/powerpc/configs/fsl-emb-nonhw.config b/arch/powerpc/configs/fsl-emb-nonhw.config
index 1a61e81..cc49c95 100644
--- a/arch/powerpc/configs/fsl-emb-nonhw.config
+++ b/arch/powerpc/configs/fsl-emb-nonhw.config
@@ -44,6 +44,7 @@ CONFIG_FORCE_MAX_ZONEORDER=13
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAME_WARN=1024
CONFIG_FTL=y
+CONFIG_GPIO_GENERIC_PLATFORM=y
CONFIG_HFS_FS=m
CONFIG_HFSPLUS_FS=m
CONFIG_HIGH_RES_TIMERS=y
@@ -104,8 +105,13 @@ CONFIG_PACKET=y
CONFIG_PARTITION_ADVANCED=y
CONFIG_PERF_EVENTS=y
CONFIG_POSIX_MQUEUE=y
+CONFIG_POWER_SUPPLY=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_GPIO=y
+CONFIG_POWER_RESET_GPIO_RESTART=y
CONFIG_QNX4FS_FS=m
CONFIG_RCU_TRACE=y
+CONFIG_RESET_CONTROLLER=y
CONFIG_ROOT_NFS=y
CONFIG_SYSV_FS=m
CONFIG_SYSVIPC=y
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 3/3] corenet: Switch to of_platform_default_populate
2016-10-23 23:48 [PATCH v2 1/3] cyrus: Add poweroff/reset support Andy Fleming
2016-10-23 23:48 ` [PATCH 2/3] 85xx: Enable gpio power/reset driver Andy Fleming
@ 2016-10-23 23:48 ` Andy Fleming
2016-10-24 21:43 ` Scott Wood
2016-11-23 7:00 ` [v2,1/3] cyrus: Add poweroff/reset support Scott Wood
2 siblings, 1 reply; 7+ messages in thread
From: Andy Fleming @ 2016-10-23 23:48 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: aperez
Many of the embedded powerpc boards use an array of device names
to register the devices from the device tree. Instead, we can use
of_platform_default_populate(), which will iterate through all the root nodes and register them.
Signed-off-by: Andy Fleming <afleming@gmail.com>
---
This is necessary to enable the gpio power/reset pins on the Cyrus board.
I have confirmed that the PCI devices are registered and that the power/reset
drivers are registered (and functional). I also tested USB, and saw the
onboard MMC card report in, so some of the SoC devices are definitely there.
If this doesn't break the other corenet boards, I'd be happy to make the
same change for the other powerpc boards.
arch/powerpc/platforms/85xx/corenet_generic.c | 49 +--------------------------
1 file changed, 1 insertion(+), 48 deletions(-)
diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc/platforms/85xx/corenet_generic.c
index 1179115..6347f20 100644
--- a/arch/powerpc/platforms/85xx/corenet_generic.c
+++ b/arch/powerpc/platforms/85xx/corenet_generic.c
@@ -83,56 +83,9 @@ void __init corenet_gen_setup_arch(void)
mpc85xx_qe_init();
}
-static const struct of_device_id of_device_ids[] = {
- {
- .compatible = "simple-bus"
- },
- {
- .compatible = "mdio-mux-gpio"
- },
- {
- .compatible = "fsl,fpga-ngpixis"
- },
- {
- .compatible = "fsl,fpga-qixis"
- },
- {
- .compatible = "fsl,srio",
- },
- {
- .compatible = "fsl,p4080-pcie",
- },
- {
- .compatible = "fsl,qoriq-pcie-v2.2",
- },
- {
- .compatible = "fsl,qoriq-pcie-v2.3",
- },
- {
- .compatible = "fsl,qoriq-pcie-v2.4",
- },
- {
- .compatible = "fsl,qoriq-pcie-v3.0",
- },
- {
- .compatible = "fsl,qe",
- },
- {
- .compatible = "fsl,fman",
- },
- /* The following two are for the Freescale hypervisor */
- {
- .name = "hypervisor",
- },
- {
- .name = "handles",
- },
- {}
-};
-
int __init corenet_gen_publish_devices(void)
{
- return of_platform_bus_probe(NULL, of_device_ids, NULL);
+ return of_platform_default_populate(NULL, NULL, NULL);
}
static const char * const boards[] __initconst = {
--
1.9.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Cyrus_5040.dts Misisng
2016-10-23 23:48 ` [PATCH 2/3] 85xx: Enable gpio power/reset driver Andy Fleming
@ 2016-10-24 16:16 ` luigi burdo
2017-07-05 15:37 ` 85xx: Enable gpio power/reset driver Darren Stevens
1 sibling, 0 replies; 7+ messages in thread
From: luigi burdo @ 2016-10-24 16:16 UTC (permalink / raw)
To: linuxppc-dev, Andy Fleming; +Cc: scottwood, matthew, Trevor Dickinson
[-- Attachment #1.1: Type: text/plain, Size: 631 bytes --]
Hi Andy,
me and some others are testing the cyrus_5040 and we sow inside the Lnx kernel there isnt the cyrus_5040.dts.
i just attched my dmsg and my lshw reports where you can see:
on dmesg there are issue on ata2 device, if i burn a cdrom i have a failure in burining , copy from to another partition some time become really slow 300kb/s (sata1 SSD to sata1 ssd partition).
if more than 3.5gb of ram is used (right now i have 16gb) we face a dma errors on pci boards.
lshw dont show L3 cache i face this on cyrus_5020 too, is this normal?
if is needed something more you can ask freely
Thanks
Luigi
[-- Attachment #1.2: Type: text/html, Size: 1213 bytes --]
[-- Attachment #2: dmesg_5040.txt --]
[-- Type: text/plain, Size: 59709 bytes --]
dmesg
[ 0.000000] Allocated 16384 bytes for 8 pacas at c00000003fffc000
[ 0.000000] MMU: Supported page sizes
[ 0.000000] 4 KB as direct
[ 0.000000] 4096 KB as direct
[ 0.000000] 16384 KB as direct
[ 0.000000] 65536 KB as direct
[ 0.000000] 262144 KB as direct
[ 0.000000] 1048576 KB as direct
[ 0.000000] MMU: Book3E HW tablewalk not supported
[ 0.000000] Linux version 4.8.0-X5000-Tlosm-LB (amigaone@Amigaone) (gcc version 6.2.0 20160927 (Ubuntu 6.2.0-5ubuntu11) ) #1 SMP PREEMPT Mon Oct 3 19:10:49 CEST 2016
[ 0.000000] Using CoreNet Generic machine description
[ 0.000000] Found legacy serial port 0 for /soc@ffe000000/serial@11c500
[ 0.000000] mem=ffe11c500, taddr=ffe11c500, irq=0, clk=400000000, speed=0
[ 0.000000] Found legacy serial port 1 for /soc@ffe000000/serial@11c600
[ 0.000000] mem=ffe11c600, taddr=ffe11c600, irq=0, clk=400000000, speed=0
[ 0.000000] Found legacy serial port 2 for /soc@ffe000000/serial@11d500
[ 0.000000] mem=ffe11d500, taddr=ffe11d500, irq=0, clk=400000000, speed=0
[ 0.000000] Found legacy serial port 3 for /soc@ffe000000/serial@11d600
[ 0.000000] mem=ffe11d600, taddr=ffe11d600, irq=0, clk=400000000, speed=0
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] (thread shift is 0)
[ 0.000000] Freed 8192 bytes for unused pacas
[ 0.000000] -----------------------------------------------------
[ 0.000000] phys_mem_size = 0xdac00000
[ 0.000000] dcache_bsize = 0x40
[ 0.000000] icache_bsize = 0x40
[ 0.000000] cpu_features = 0x00180400581802c0
[ 0.000000] possible = 0x00180480581802c0
[ 0.000000] always = 0x00180400581802c0
[ 0.000000] cpu_user_features = 0xcc008000 0x08000000
[ 0.000000] mmu_features = 0x000a0010
[ 0.000000] firmware_features = 0x0000000000000000
[ 0.000000] -----------------------------------------------------
[ 0.000000] CoreNet Generic board
[ 0.000000] Top of RAM: 0xdac00000, Total RAM: 0xdac00000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal [mem 0x0000000080000000-0x00000000dabfffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x00000000dabfffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000dabfffff]
[ 0.000000] On node 0 totalpages: 896000
[ 0.000000] free_area_init_node: node 0, pgdat c0000000010b75c0, node_mem_map c0000000d7b94000
[ 0.000000] DMA zone: 7168 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 524288 pages, LIFO batch:31
[ 0.000000] Normal zone: 5082 pages used for memmap
[ 0.000000] Normal zone: 371712 pages, LIFO batch:31
[ 0.000000] MMU: Allocated 2112 bytes of context maps for 255 contexts
[ 0.000000] percpu: Embedded 19 pages/cpu @c0000000d7a00000 s37096 r0 d40728 u262144
[ 0.000000] pcpu-alloc: s37096 r0 d40728 u262144 alloc=1*1048576
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 883750
[ 0.000000] Kernel command line: root=/dev/sda2 mem=3500M radeon.pcie_gen2=1 pci=realloc
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 3441728K/3584000K available (10660K kernel code, 1856K rwdata, 5556K rodata, 384K init, 1458K bss, 142272K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe040000, max 4 CPUs
[ 0.000000] mpic: ISU size: 512, shift: 9, mask: 1ff
[ 0.000000] mpic: Initializing for 512 sources
[ 0.000000] time_init: decrementer frequency = 50.000000 MHz
[ 0.000000] time_init: processor frequency = 2200.000000 MHz
[ 0.000003] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
[ 0.000008] clocksource: timebase mult[14000000] shift[24] registered
[ 0.000013] clockevent: decrementer mult[ccccccd] shift[32] cpu[0]
[ 0.000859] Console: colour dummy device 80x25
[ 0.001171] console [tty0] enabled
[ 0.001186] pid_max: default: 32768 minimum: 301
[ 0.001232] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.001243] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.001764] e500 family performance monitor hardware support registered
[ 0.020349] Brought up 4 CPUs
[ 0.020608] devtmpfs: initialized
[ 0.024219] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.024291] xor: measuring software checksum speed
[ 0.034182] 8regs : 4508.000 MB/sec
[ 0.044201] 8regs_prefetch: 4180.000 MB/sec
[ 0.054221] 32regs : 4792.000 MB/sec
[ 0.064241] 32regs_prefetch: 4180.000 MB/sec
[ 0.064249] xor: using function: 32regs (4792.000 MB/sec)
[ 0.064259] prandom: seed boundary self test passed
[ 0.065320] prandom: 100 self tests passed
[ 0.065725] NET: Registered protocol family 16
[ 0.071269] cpuidle: using governor ladder
[ 0.075278] cpuidle: using governor menu
[ 0.087578] Found FSL PCI host bridge at 0x0000000ffe200000. Firmware bus number: 0->1
[ 0.087594] PCI host bridge /pcie@ffe200000 ranges:
[ 0.087604] MEM 0x0000000c00000000..0x0000000c1fffffff -> 0x00000000e0000000
[ 0.087615] IO 0x0000000ff8000000..0x0000000ff800ffff -> 0x0000000000000000
[ 0.087632] /pcie@ffe200000: PCICSRBAR @ 0xdf000000
[ 0.087639] setup_pci_atmu: end of DRAM dac00000
[ 0.087650] /pcie@ffe200000: Setting PCI inbound window greater than memory size
[ 0.087909] Found FSL PCI host bridge at 0x0000000ffe201000. Firmware bus number: 0->8
[ 0.087920] PCI host bridge /pcie@ffe201000 ranges:
[ 0.087930] MEM 0x0000000c20000000..0x0000000c3fffffff -> 0x00000000e0000000
[ 0.087940] IO 0x0000000ff8010000..0x0000000ff801ffff -> 0x0000000000000000
[ 0.087956] /pcie@ffe201000: PCICSRBAR @ 0xdf000000
[ 0.087963] setup_pci_atmu: end of DRAM dac00000
[ 0.087973] /pcie@ffe201000: Setting PCI inbound window greater than memory size
[ 0.088875] iommu: Adding device ff4200000.qman-portal to group 0
[ 0.088900] iommu: Adding device ff4204000.qman-portal to group 1
[ 0.088919] iommu: Adding device ff4208000.qman-portal to group 2
[ 0.088938] iommu: Adding device ff420c000.qman-portal to group 3
[ 0.088958] iommu: Adding device ff4210000.qman-portal to group 4
[ 0.088977] iommu: Adding device ff4214000.qman-portal to group 5
[ 0.088996] iommu: Adding device ff4218000.qman-portal to group 6
[ 0.089015] iommu: Adding device ff421c000.qman-portal to group 7
[ 0.089036] iommu: Adding device ff4220000.qman-portal to group 8
[ 0.089057] iommu: Adding device ff4224000.qman-portal to group 9
[ 0.089099] iommu: Adding device ffe488000.port to group 10
[ 0.089120] iommu: Adding device ffe489000.port to group 11
[ 0.089142] iommu: Adding device ffe48a000.port to group 12
[ 0.089162] iommu: Adding device ffe48b000.port to group 13
[ 0.089182] iommu: Adding device ffe48c000.port to group 14
[ 0.089202] iommu: Adding device ffe490000.port to group 15
[ 0.089236] iommu: Adding device ffe588000.port to group 16
[ 0.089256] iommu: Adding device ffe589000.port to group 17
[ 0.089276] iommu: Adding device ffe58a000.port to group 18
[ 0.089297] iommu: Adding device ffe58b000.port to group 19
[ 0.089317] iommu: Adding device ffe58c000.port to group 20
[ 0.089349] iommu: Adding device ffe590000.port to group 21
[ 0.089388] iommu: Adding device ffe100300.dma to group 22
[ 0.089407] iommu: Adding device ffe101300.dma to group 23
[ 0.089425] iommu: Adding device ffe114000.sdhc to group 24
[ 0.089452] iommu: Adding device ffe210000.usb to group 25
[ 0.089470] iommu: Adding device ffe211000.usb to group 26
[ 0.089491] iommu: Adding device ffe220000.sata to group 27
[ 0.089509] iommu: Adding device ffe221000.sata to group 28
[ 0.089531] iommu: Adding device ffe318000.qman to group 29
[ 0.089550] iommu: Adding device ffe31a000.bman to group 30
[ 0.089569] iommu: Adding device ffe200000.pcie to group 31
[ 0.089589] iommu: Adding device ffe201000.pcie to group 32
[ 0.097491] PCI: Probing PCI hardware
[ 0.097625] fsl-pci ffe200000.pcie: PCI host bridge to bus 0000:00
[ 0.097638] pci_bus 0000:00: root bus resource [io 0x8000080000010000-0x800008000001ffff] (bus address [0x0000-0xffff])
[ 0.097652] pci_bus 0000:00: root bus resource [mem 0xc00000000-0xc1fffffff] (bus address [0xe0000000-0xffffffff])
[ 0.097666] pci_bus 0000:00: root bus resource [bus 00-01]
[ 0.097676] pci_bus 0000:00: busn_res: [bus 00-01] end is updated to ff
[ 0.097694] pci 0000:00:00.0: [1957:0451] type 01 class 0x0b2000
[ 0.097709] pci 0000:00:00.0: reg 0x10: [mem 0xdf000000-0xdfffffff]
[ 0.097755] pci 0000:00:00.0: supports D1 D2
[ 0.097758] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.097817] iommu: Removing device ffe200000.pcie from group 31
[ 0.097841] iommu: Adding device 0000:00:00.0 to group 33
[ 0.098027] pci 0000:01:00.0: [1002:6742] type 00 class 0x030000
[ 0.098047] pci 0000:01:00.0: reg 0x10: [mem 0xc00000000-0xc0fffffff 64bit pref]
[ 0.098059] pci 0000:01:00.0: reg 0x18: [mem 0xc10000000-0xc1001ffff 64bit]
[ 0.098068] pci 0000:01:00.0: reg 0x20: [io 0x8000080000011000-0x80000800000110ff]
[ 0.098083] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[ 0.098140] pci 0000:01:00.0: supports D1 D2
[ 0.098197] iommu: Adding device 0000:01:00.0 to group 33
[ 0.098253] pci 0000:01:00.1: [1002:aa90] type 00 class 0x040300
[ 0.098272] pci 0000:01:00.1: reg 0x10: [mem 0xc10020000-0xc10023fff 64bit]
[ 0.098358] pci 0000:01:00.1: supports D1 D2
[ 0.098413] iommu: Adding device 0000:01:00.1 to group 33
[ 0.101503] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.101516] pci 0000:00:00.0: bridge window [io 0x8000080000011000-0x8000080000011fff]
[ 0.101520] pci 0000:00:00.0: bridge window [mem 0xc00000000-0xc100fffff]
[ 0.101572] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.101577] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.101651] fsl-pci ffe201000.pcie: PCI host bridge to bus 1000:00
[ 0.101663] pci_bus 1000:00: root bus resource [io 0x8000080000021000-0x8000080000030fff] (bus address [0x0000-0xffff])
[ 0.101677] pci_bus 1000:00: root bus resource [mem 0xc20000000-0xc3fffffff] (bus address [0xe0000000-0xffffffff])
[ 0.101690] pci_bus 1000:00: root bus resource [bus 00-08]
[ 0.101699] pci_bus 1000:00: busn_res: [bus 00-08] end is updated to ff
[ 0.101713] pci 1000:00:00.0: [1957:0451] type 01 class 0x0b2000
[ 0.101723] pci 1000:00:00.0: reg 0x10: [mem 0xdf000000-0xdfffffff]
[ 0.101759] pci 1000:00:00.0: supports D1 D2
[ 0.101762] pci 1000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.101817] iommu: Removing device ffe201000.pcie from group 32
[ 0.101838] iommu: Adding device 1000:00:00.0 to group 31
[ 0.102004] pci 1000:01:00.0: [111d:8092] type 01 class 0x060400
[ 0.102136] pci 1000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.102196] iommu: Adding device 1000:01:00.0 to group 31
[ 0.104508] pci 1000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.104521] pci 1000:00:00.0: bridge window [io 0x8000080000022000-0x8000080000022fff]
[ 0.104525] pci 1000:00:00.0: bridge window [mem 0xc20000000-0xc200fffff]
[ 0.104652] pci 1000:02:01.0: [111d:8092] type 01 class 0x060400
[ 0.104799] pci 1000:02:01.0: PME# supported from D0 D3hot D3cold
[ 0.104860] iommu: Adding device 1000:02:01.0 to group 31
[ 0.104920] pci 1000:02:02.0: [111d:8092] type 01 class 0x060400
[ 0.105067] pci 1000:02:02.0: PME# supported from D0 D3hot D3cold
[ 0.105129] iommu: Adding device 1000:02:02.0 to group 31
[ 0.105191] pci 1000:02:03.0: [111d:8092] type 01 class 0x060400
[ 0.105338] pci 1000:02:03.0: PME# supported from D0 D3hot D3cold
[ 0.105400] iommu: Adding device 1000:02:03.0 to group 31
[ 0.105470] pci 1000:02:08.0: [111d:8092] type 01 class 0x060400
[ 0.105625] pci 1000:02:08.0: PME# supported from D0 D3hot D3cold
[ 0.105687] iommu: Adding device 1000:02:08.0 to group 31
[ 0.105759] pci 1000:02:10.0: [111d:8092] type 01 class 0x060400
[ 0.105887] pci 1000:02:10.0: PME# supported from D0 D3hot D3cold
[ 0.105945] iommu: Adding device 1000:02:10.0 to group 31
[ 0.106012] pci 1000:01:00.0: PCI bridge to [bus 02-ff]
[ 0.106029] pci 1000:01:00.0: bridge window [io 0x8000080000022000-0x8000080000022fff]
[ 0.106036] pci 1000:01:00.0: bridge window [mem 0xc20000000-0xc200fffff]
[ 0.106222] pci 1000:03:00.0: [12d8:e111] type 01 class 0x060400
[ 0.106359] pci 1000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.106437] iommu: Adding device 1000:03:00.0 to group 31
[ 0.108526] pci 1000:02:01.0: PCI bridge to [bus 03-ff]
[ 0.108543] pci 1000:02:01.0: bridge window [io 0x8000080000022000-0x8000080000022fff]
[ 0.108550] pci 1000:02:01.0: bridge window [mem 0xc20000000-0xc200fffff]
[ 0.108705] pci 1000:04:04.0: [10ec:8169] type 00 class 0x020000
[ 0.108730] pci 1000:04:04.0: reg 0x10: [io 0x8000080000022000-0x80000800000220ff]
[ 0.108743] pci 1000:04:04.0: reg 0x14: [mem 0xc20000000-0xc200000ff]
[ 0.108807] pci 1000:04:04.0: reg 0x30: [mem 0x534c0000-0x534dffff pref]
[ 0.108859] pci 1000:04:04.0: supports D1 D2
[ 0.108862] pci 1000:04:04.0: PME# supported from D1 D2 D3hot D3cold
[ 0.108913] iommu: Adding device 1000:04:04.0 to group 31
[ 0.108970] pci 1000:04:05.0: [1095:3114] type 00 class 0x010400
[ 0.108995] pci 1000:04:05.0: reg 0x10: [io 0x8000080000022100-0x8000080000022107]
[ 0.109008] pci 1000:04:05.0: reg 0x14: [io 0x8000080000022108-0x800008000002210b]
[ 0.109021] pci 1000:04:05.0: reg 0x18: [io 0x8000080000022110-0x8000080000022117]
[ 0.109034] pci 1000:04:05.0: reg 0x1c: [io 0x8000080000022118-0x800008000002211b]
[ 0.109048] pci 1000:04:05.0: reg 0x20: [io 0x8000080000022120-0x800008000002212f]
[ 0.109061] pci 1000:04:05.0: reg 0x24: [mem 0xc20000400-0xc200007ff]
[ 0.109074] pci 1000:04:05.0: reg 0x30: [mem 0x00000000-0x0007ffff pref]
[ 0.109125] pci 1000:04:05.0: supports D1 D2
[ 0.109172] iommu: Adding device 1000:04:05.0 to group 31
[ 0.109267] pci 1000:03:00.0: PCI bridge to [bus 04-ff]
[ 0.109284] pci 1000:03:00.0: bridge window [io 0x8000080000022000-0x8000080000022fff]
[ 0.109290] pci 1000:03:00.0: bridge window [mem 0xc20000000-0xc200fffff]
[ 0.109336] pci_bus 1000:04: busn_res: [bus 04-ff] end is updated to 04
[ 0.109341] pci_bus 1000:03: busn_res: [bus 03-ff] end is updated to 04
[ 0.109438] pci 1000:02:02.0: PCI bridge to [bus 05-ff]
[ 0.109470] pci_bus 1000:05: busn_res: [bus 05-ff] end is updated to 05
[ 0.109571] pci 1000:02:03.0: PCI bridge to [bus 06-ff]
[ 0.109603] pci_bus 1000:06: busn_res: [bus 06-ff] end is updated to 06
[ 0.109698] pci 1000:02:08.0: PCI bridge to [bus 07-ff]
[ 0.109730] pci_bus 1000:07: busn_res: [bus 07-ff] end is updated to 07
[ 0.109822] pci 1000:02:10.0: PCI bridge to [bus 08-ff]
[ 0.109854] pci_bus 1000:08: busn_res: [bus 08-ff] end is updated to 08
[ 0.109858] pci_bus 1000:02: busn_res: [bus 02-ff] end is updated to 08
[ 0.109863] pci_bus 1000:01: busn_res: [bus 01-ff] end is updated to 08
[ 0.109867] pci_bus 1000:00: busn_res: [bus 00-ff] end is updated to 08
[ 0.109881] PCI: Cannot allocate resource region 0 of device 0000:00:00.0, will remap
[ 0.109900] PCI: Cannot allocate resource region 0 of device 1000:00:00.0, will remap
[ 0.109933] PCI: Cannot allocate resource region 6 of device 1000:04:04.0, will remap
[ 0.109985] PCI 0000:00 Cannot reserve Legacy IO [io 0x8000080000010000-0x10fff]
[ 0.109988] PCI 1000:00 Cannot reserve Legacy IO [io 0x8000080000021000-0x21fff]
[ 0.109992] pci_bus 0000:00: max bus depth: 1 pci_try_num: 2
[ 0.110004] pci 0000:00:00.0: BAR 0: no space for [mem size 0x01000000]
[ 0.110014] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x01000000]
[ 0.110026] pci 0000:01:00.0: BAR 6: assigned [mem 0xc10040000-0xc1005ffff pref]
[ 0.110037] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.110047] pci 0000:00:00.0: bridge window [io 0x8000080000010000-0x800008000001ffff]
[ 0.110059] pci 0000:00:00.0: bridge window [mem 0xc00000000-0xc1fffffff]
[ 0.110070] pci_bus 0000:00: No. 2 try to assign unassigned res
[ 0.110078] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.110087] pci 0000:00:00.0: bridge window [io 0x8000080000010000-0x800008000001ffff]
[ 0.110099] pci 0000:00:00.0: bridge window [mem 0xc00000000-0xc1fffffff]
[ 0.110112] pci_bus 0000:00: resource 4 [io 0x8000080000010000-0x800008000001ffff]
[ 0.110115] pci_bus 0000:00: resource 5 [mem 0xc00000000-0xc1fffffff]
[ 0.110118] pci_bus 0000:01: resource 0 [io 0x8000080000010000-0x800008000001ffff]
[ 0.110121] pci_bus 0000:01: resource 1 [mem 0xc00000000-0xc1fffffff]
[ 0.110124] pci_bus 1000:00: max bus depth: 4 pci_try_num: 5
[ 0.110204] pci 1000:00:00.0: BAR 0: no space for [mem size 0x01000000]
[ 0.110214] pci 1000:00:00.0: BAR 0: failed to assign [mem size 0x01000000]
[ 0.110226] pci 1000:04:05.0: BAR 6: assigned [mem 0xc20080000-0xc200fffff pref]
[ 0.110238] pci 1000:04:04.0: BAR 6: assigned [mem 0xc20020000-0xc2003ffff pref]
[ 0.110248] pci 1000:03:00.0: PCI bridge to [bus 04]
[ 0.110259] pci 1000:03:00.0: bridge window [io 0x8000080000022000-0x8000080000022fff]
[ 0.110271] pci 1000:03:00.0: bridge window [mem 0xc20000000-0xc200fffff]
[ 0.110284] pci 1000:02:01.0: PCI bridge to [bus 03-04]
[ 0.110294] pci 1000:02:01.0: bridge window [io 0x8000080000022000-0x8000080000022fff]
[ 0.110306] pci 1000:02:01.0: bridge window [mem 0xc20000000-0xc200fffff]
[ 0.110321] pci 1000:02:02.0: PCI bridge to [bus 05]
[ 0.110340] pci 1000:02:03.0: PCI bridge to [bus 06]
[ 0.110359] pci 1000:02:08.0: PCI bridge to [bus 07]
[ 0.110378] pci 1000:02:10.0: PCI bridge to [bus 08]
[ 0.110397] pci 1000:01:00.0: PCI bridge to [bus 02-08]
[ 0.110407] pci 1000:01:00.0: bridge window [io 0x8000080000022000-0x8000080000022fff]
[ 0.110419] pci 1000:01:00.0: bridge window [mem 0xc20000000-0xc200fffff]
[ 0.110434] pci 1000:00:00.0: PCI bridge to [bus 01-08]
[ 0.110444] pci 1000:00:00.0: bridge window [io 0x8000080000021000-0x8000080000030fff]
[ 0.110456] pci 1000:00:00.0: bridge window [mem 0xc20000000-0xc3fffffff]
[ 0.110467] pci_bus 1000:00: No. 2 try to assign unassigned res
[ 0.110553] pci 1000:03:00.0: PCI bridge to [bus 04]
[ 0.110564] pci 1000:03:00.0: bridge window [io 0x8000080000022000-0x8000080000022fff]
[ 0.110576] pci 1000:03:00.0: bridge window [mem 0xc20000000-0xc200fffff]
[ 0.110589] pci 1000:02:01.0: PCI bridge to [bus 03-04]
[ 0.110600] pci 1000:02:01.0: bridge window [io 0x8000080000022000-0x8000080000022fff]
[ 0.110612] pci 1000:02:01.0: bridge window [mem 0xc20000000-0xc200fffff]
[ 0.110627] pci 1000:02:02.0: PCI bridge to [bus 05]
[ 0.110646] pci 1000:02:03.0: PCI bridge to [bus 06]
[ 0.110664] pci 1000:02:08.0: PCI bridge to [bus 07]
[ 0.110683] pci 1000:02:10.0: PCI bridge to [bus 08]
[ 0.110703] pci 1000:01:00.0: PCI bridge to [bus 02-08]
[ 0.110713] pci 1000:01:00.0: bridge window [io 0x8000080000022000-0x8000080000022fff]
[ 0.110725] pci 1000:01:00.0: bridge window [mem 0xc20000000-0xc200fffff]
[ 0.110740] pci 1000:00:00.0: PCI bridge to [bus 01-08]
[ 0.110750] pci 1000:00:00.0: bridge window [io 0x8000080000021000-0x8000080000030fff]
[ 0.110762] pci 1000:00:00.0: bridge window [mem 0xc20000000-0xc3fffffff]
[ 0.110773] pci_bus 1000:00: resource 4 [io 0x8000080000021000-0x8000080000030fff]
[ 0.110776] pci_bus 1000:00: resource 5 [mem 0xc20000000-0xc3fffffff]
[ 0.110780] pci_bus 1000:01: resource 0 [io 0x8000080000021000-0x8000080000030fff]
[ 0.110783] pci_bus 1000:01: resource 1 [mem 0xc20000000-0xc3fffffff]
[ 0.110786] pci_bus 1000:02: resource 0 [io 0x8000080000022000-0x8000080000022fff]
[ 0.110789] pci_bus 1000:02: resource 1 [mem 0xc20000000-0xc200fffff]
[ 0.110792] pci_bus 1000:03: resource 0 [io 0x8000080000022000-0x8000080000022fff]
[ 0.110795] pci_bus 1000:03: resource 1 [mem 0xc20000000-0xc200fffff]
[ 0.110798] pci_bus 1000:04: resource 0 [io 0x8000080000022000-0x8000080000022fff]
[ 0.110801] pci_bus 1000:04: resource 1 [mem 0xc20000000-0xc200fffff]
[ 0.110803] PCI: Probing PCI hardware done
[ 0.111473] Setting up Freescale MSI support
[ 0.111756] Setting up Freescale MSI support
[ 0.112024] Setting up Freescale MSI support
[ 0.146714] raid6: int64x1 gen() 789 MB/s
[ 0.163738] raid6: int64x1 xor() 574 MB/s
[ 0.180735] raid6: int64x2 gen() 1207 MB/s
[ 0.197780] raid6: int64x2 xor() 798 MB/s
[ 0.214854] raid6: int64x4 gen() 1218 MB/s
[ 0.231876] raid6: int64x4 xor() 753 MB/s
[ 0.248917] raid6: int64x8 gen() 1183 MB/s
[ 0.265975] raid6: int64x8 xor() 757 MB/s
[ 0.265982] raid6: using algorithm int64x4 gen() 1218 MB/s
[ 0.265990] raid6: .... xor() 753 MB/s, rmw enabled
[ 0.265997] raid6: using intx1 recovery algorithm
[ 0.266144] Freescale Elo series DMA driver
[ 0.266455] fsl-elo-dma ffe100300.dma: #0 (fsl,eloplus-dma-channel), irq 28
[ 0.266489] fsl-elo-dma ffe100300.dma: #1 (fsl,eloplus-dma-channel), irq 29
[ 0.266523] fsl-elo-dma ffe100300.dma: #2 (fsl,eloplus-dma-channel), irq 30
[ 0.266557] fsl-elo-dma ffe100300.dma: #3 (fsl,eloplus-dma-channel), irq 31
[ 0.266836] fsl-elo-dma ffe101300.dma: #0 (fsl,eloplus-dma-channel), irq 32
[ 0.266870] fsl-elo-dma ffe101300.dma: #1 (fsl,eloplus-dma-channel), irq 33
[ 0.266904] fsl-elo-dma ffe101300.dma: #2 (fsl,eloplus-dma-channel), irq 34
[ 0.266938] fsl-elo-dma ffe101300.dma: #3 (fsl,eloplus-dma-channel), irq 35
[ 0.267628] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=none,locks=none
[ 0.267652] vgaarb: loaded
[ 0.267658] vgaarb: bridge control possible 0000:01:00.0
[ 0.268070] SCSI subsystem initialized
[ 0.268206] libata version 3.00 loaded.
[ 0.268415] usbcore: registered new interface driver usbfs
[ 0.268466] usbcore: registered new interface driver hub
[ 0.268520] usbcore: registered new device driver usb
[ 0.268686] pps_core: LinuxPPS API ver. 1 registered
[ 0.268695] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.268732] PTP clock support registered
[ 0.268853] EDAC MC: Ver: 3.0.0
[ 0.269537] Advanced Linux Sound Architecture Driver Initialized.
[ 0.270131] clocksource: Switched to clocksource timebase
[ 0.274980] NET: Registered protocol family 2
[ 0.275280] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.275430] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
[ 0.275949] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.276020] UDP hash table entries: 2048 (order: 5, 196608 bytes)
[ 0.276156] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
[ 0.276374] NET: Registered protocol family 1
[ 0.276605] RPC: Registered named UNIX socket transport module.
[ 0.276619] RPC: Registered udp transport module.
[ 0.276625] RPC: Registered tcp transport module.
[ 0.276633] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.276706] PCI: CLS 32 bytes, default 64
[ 0.277512] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.277720] workingset: timestamp_bits=62 max_order=20 bucket_order=0
[ 0.282069] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.282842] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.283056] fuse init (API version 7.25)
[ 0.284825] async_tx: api initialized (async)
[ 0.284909] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.284921] io scheduler noop registered
[ 0.284928] io scheduler deadline registered
[ 0.284993] io scheduler cfq registered (default)
[ 0.285884] crc32: CRC_LE_BITS = 64, CRC_BE BITS = 64
[ 0.285892] crc32: self tests passed, processed 225944 bytes in 423980 nsec
[ 0.286344] crc32c: CRC_LE_BITS = 64
[ 0.286351] crc32c: self tests passed, processed 225944 bytes in 215540 nsec
[ 0.316197] crc32_combine: 8373 self tests passed
[ 0.346628] crc32c_combine: 8373 self tests passed
[ 0.346647] glob: 64 self-tests passed, 0 failed
[ 0.348244] aer 0000:00:00.0:pcie002: service driver aer loaded
[ 0.348305] aer 1000:00:00.0:pcie002: service driver aer loaded
[ 0.371404] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.372044] serial8250.0: ttyS0 at MMIO 0xffe11c500 (irq = 36, base_baud = 25000000) is a 16550A
[ 0.372488] serial8250.0: ttyS1 at MMIO 0xffe11c600 (irq = 36, base_baud = 25000000) is a 16550A
[ 0.372564] serial8250 serial8250.0: unable to register port at index 2 (IO0 MEMffe11d500 IRQ37): -28
[ 0.372577] serial8250 serial8250.0: unable to register port at index 3 (IO0 MEMffe11d600 IRQ37): -28
[ 0.372687] ePAPR hypervisor byte channel driver
[ 0.372923] [drm] Initialized drm 1.1.0 20060810
[ 0.372949] [drm] radeon kernel modesetting enabled.
[ 0.373241] [drm] initializing kernel modesetting (TURKS 0x1002:0x6742 0x174B:0x6570 0x00).
[ 0.373265] [drm] register mmio base: 0x10000000
[ 0.373272] [drm] register mmio size: 131072
[ 0.551117] ATOM BIOS: Turks
[ 0.551287] radeon 0000:01:00.0: VRAM: 2048M 0x0000000000000000 - 0x000000007FFFFFFF (2048M used)
[ 0.551300] radeon 0000:01:00.0: GTT: 1024M 0x0000000080000000 - 0x00000000BFFFFFFF
[ 0.551310] [drm] Detected VRAM RAM=2048M, BAR=256M
[ 0.551317] [drm] RAM width 128bits DDR
[ 0.551398] [TTM] Zone kernel: Available graphics memory: 1754350 kiB
[ 0.551406] [TTM] Initializing pool allocator
[ 0.551420] [TTM] Initializing DMA pool allocator
[ 0.551472] [drm] radeon: 2048M of VRAM memory ready
[ 0.551480] [drm] radeon: 1024M of GTT memory ready.
[ 0.551488] [drm] Loading TURKS Microcode
[ 0.551505] [drm] Internal thermal controller with fan control
[ 0.555924] [drm] radeon: dpm initialized
[ 0.555978] [drm] GART: num cpu pages 262144, num gpu pages 262144
[ 0.557809] [drm] enabling PCIE gen 2 link speeds, disable with radeon.pcie_gen2=0
[ 0.591295] [drm] PCIE GART of 1024M enabled (table at 0x0000000000162000).
[ 0.591461] radeon 0000:01:00.0: WB enabled
[ 0.591472] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000080000c00 and cpu addr 0xc0000000d2d87c00
[ 0.591486] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x0000000080000c0c and cpu addr 0xc0000000d2d87c0c
[ 0.595699] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x0000000000072118 and cpu addr 0x80000800801b2118
[ 0.595713] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 0.595721] [drm] Driver supports precise vblank timestamp query.
[ 0.595730] radeon 0000:01:00.0: radeon: MSI limited to 32-bit
[ 0.595785] radeon 0000:01:00.0: radeon: using MSI.
[ 0.595828] [drm] radeon: irq initialized.
[ 0.612501] [drm] ring test on 0 succeeded in 2 usecs
[ 0.612521] [drm] ring test on 3 succeeded in 7 usecs
[ 0.789658] [drm] ring test on 5 succeeded in 2 usecs
[ 0.789675] [drm] UVD initialized successfully.
[ 0.789929] [drm] ib test on ring 0 succeeded in 0 usecs
[ 0.789997] [drm] ib test on ring 3 succeeded in 0 usecs
[ 1.448170] [drm] ib test on ring 5 succeeded
[ 1.454322] [drm] Radeon Display Connectors
[ 1.454331] [drm] Connector 0:
[ 1.454337] [drm] HDMI-A-1
[ 1.454342] [drm] HPD1
[ 1.454349] [drm] DDC: 0x6470 0x6470 0x6474 0x6474 0x6478 0x6478 0x647c 0x647c
[ 1.454358] [drm] Encoders:
[ 1.454364] [drm] DFP1: INTERNAL_UNIPHY2
[ 1.454370] [drm] Connector 1:
[ 1.454375] [drm] DVI-D-1
[ 1.454381] [drm] HPD4
[ 1.454387] [drm] DDC: 0x6450 0x6450 0x6454 0x6454 0x6458 0x6458 0x645c 0x645c
[ 1.454396] [drm] Encoders:
[ 1.454402] [drm] DFP2: INTERNAL_UNIPHY
[ 1.454408] [drm] Connector 2:
[ 1.454413] [drm] VGA-1
[ 1.454420] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[ 1.454428] [drm] Encoders:
[ 1.454434] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 1.551710] [drm] fb mappable at 0xC00363000
[ 1.551719] [drm] vram apper at 0xC00000000
[ 1.551725] [drm] size 8294400
[ 1.551730] [drm] fb depth is 24
[ 1.551736] [drm] pitch is 7680
[ 1.710049] Console: switching to colour frame buffer device 240x67
[ 1.734440] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[ 1.734639] [drm] Initialized radeon 2.46.0 20080528 for 0000:01:00.0 on minor 0
[ 1.738675] brd: module loaded
[ 1.740821] loop: module loaded
[ 2.796224] Loading iSCSI transport class v2.0-870.
[ 2.796624] iscsi: registered transport (tcp)
[ 2.797845] fsl-sata ffe220000.sata: Sata FSL Platform/CSB Driver init
[ 2.798350] scsi host0: sata_fsl
[ 2.798531] ata1: SATA max UDMA/133 irq 68
[ 2.798644] fsl-sata ffe221000.sata: Sata FSL Platform/CSB Driver init
[ 2.799008] scsi host1: sata_fsl
[ 2.799146] ata2: SATA max UDMA/133 irq 69
[ 2.799566] sata_sil 1000:04:05.0: version 2.4
[ 2.799633] sata_sil 1000:04:05.0: Applying R_ERR on DMA activate FIS errata fix
[ 2.800389] scsi host2: sata_sil
[ 2.800583] scsi host3: sata_sil
[ 2.800773] scsi host4: sata_sil
[ 2.800962] scsi host5: sata_sil
[ 2.801095] ata3: SATA max UDMA/100 mmio m1024@0xc20000400 tf 0xc20000480 irq 19
[ 2.801250] ata4: SATA max UDMA/100 mmio m1024@0xc20000400 tf 0xc200004c0 irq 19
[ 2.801398] ata5: SATA max UDMA/100 mmio m1024@0xc20000400 tf 0xc20000680 irq 19
[ 2.801544] ata6: SATA max UDMA/100 mmio m1024@0xc20000400 tf 0xc200006c0 irq 19
[ 2.801867] platform physmap-flash.0: failed to claim resource 0
[ 2.802927] fsl_espi ffe110000.spi: at 0x8000080080068000 (irq = 53)
[ 2.803805] libphy: Fixed MDIO Bus: probed
[ 2.804390] libphy: Freescale PowerQUICC MII Bus: probed
[ 2.805222] libphy: Freescale XGMAC MDIO Bus: probed
[ 2.805746] fsl-fman ffe400000.fman: read_dts_node: Failed to get FM0 clock structure
[ 2.805906] fsl-fman: probe of ffe400000.fman failed with error -5
[ 2.806063] fsl-fman ffe500000.fman: read_dts_node: Failed to get FM1 clock structure
[ 2.806236] fsl-fman: probe of ffe500000.fman failed with error -5
[ 2.806935] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.807074] r8169 1000:04:04.0 (unnamed net_device) (uninitialized): not PCI Express
[ 2.807558] r8169 1000:04:04.0 eth0: RTL8169sb/8110sb at 0x800008008006e000, 60:e3:27:05:53:20, XID 10000000 IRQ 18
[ 2.807763] r8169 1000:04:04.0 eth0: jumbo features [frames: 7152 bytes, tx checksumming: ok]
[ 2.807969] PPP generic driver version 2.4.2
[ 2.808131] PPP BSD Compression module registered
[ 2.808235] PPP Deflate Compression module registered
[ 2.812735] NET: Registered protocol family 24
[ 2.817303] VFIO - User Level meta-driver version: 0.3
[ 2.822006] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.826690] ehci-pci: EHCI PCI platform driver
[ 2.831249] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.836042] ohci-pci: OHCI PCI platform driver
[ 2.841316] ehci-fsl: Freescale EHCI Host controller driver
[ 2.846064] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 2.850881] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 2.865689] fsl-ehci fsl-ehci.0: irq 44, io mem 0xffe210000
[ 2.877136] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 2.881902] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.886682] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.891498] usb usb1: Product: Freescale On-Chip EHCI Host Controller
[ 2.896373] usb usb1: Manufacturer: Linux 4.8.0-X5000-Tlosm-LB ehci_hcd
[ 2.901254] usb usb1: SerialNumber: fsl-ehci.0
[ 2.906256] hub 1-0:1.0: USB hub found
[ 2.911092] hub 1-0:1.0: 1 port detected
[ 2.915998] fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
[ 2.920943] fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
[ 2.935929] fsl-ehci fsl-ehci.1: irq 45, io mem 0xffe211000
[ 2.947135] fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
[ 2.952152] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.957212] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.962260] usb usb2: Product: Freescale On-Chip EHCI Host Controller
[ 2.967294] usb usb2: Manufacturer: Linux 4.8.0-X5000-Tlosm-LB ehci_hcd
[ 2.972307] usb usb2: SerialNumber: fsl-ehci.1
[ 2.977411] hub 2-0:1.0: USB hub found
[ 2.982384] hub 2-0:1.0: 1 port detected
[ 2.987435] usbcore: registered new interface driver usblp
[ 2.992457] usbcore: registered new interface driver usb-storage
[ 2.997414] usbcore: registered new interface driver usbserial
[ 3.002278] usbcore: registered new interface driver usbserial_generic
[ 3.007117] usbserial: USB Serial support registered for generic
[ 3.011946] usbcore: registered new interface driver ftdi_sio
[ 3.016781] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 3.021901] mousedev: PS/2 mouse device common for all mice
[ 3.026984] usbcore: registered new interface driver iforce
[ 3.032098] usbcore: registered new interface driver xpad
[ 3.037447] i2c /dev entries driver
[ 3.042819] mpc-i2c ffe118100.i2c: timeout 1000000 us
[ 3.047894] mpc-i2c ffe119100.i2c: timeout 1000000 us
[ 3.055376] rtc-ds1307 9-006f: rtc core: registered mcp7941x as rtc0
[ 3.060328] rtc-ds1307 9-006f: 64 bytes nvram
[ 3.065514] mpc-i2c ffe118000.i2c: timeout 1000000 us
[ 3.070651] mpc-i2c ffe119000.i2c: timeout 1000000 us
[ 3.075920] md: linear personality registered for level -1
[ 3.080844] md: raid0 personality registered for level 0
[ 3.085747] md: raid1 personality registered for level 1
[ 3.090635] md: raid10 personality registered for level 10
[ 3.095584] md: raid6 personality registered for level 6
[ 3.100417] md: raid5 personality registered for level 5
[ 3.105163] md: raid4 personality registered for level 4
[ 3.109339] ata3: SATA link down (SStatus 0 SControl 310)
[ 3.114696] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[ 3.119433] Freescale(R) MPC85xx EDAC driver, (C) 2006 Montavista Software
[ 3.124769] mpc85xx_mc_err_probe: No ECC DIMMs discovered
[ 3.129490] mpc85xx_mc_err_probe: No ECC DIMMs discovered
[ 3.135079] EDAC PCI0: Giving out device to module MPC85xx_edac controller mpc85xx_pci_err: DEV mpc85xx-pci-edac.0.auto (INTERRUPT)
[ 3.139850] genirq: irq 482 uses trigger mode 4; requested 0
[ 3.144614] MPC85xx_edac acquired irq 482 for PCI Err
[ 3.149379] MPC85xx_edac PCI err registered
[ 3.154137] EDAC PCI1: Giving out device to module MPC85xx_edac controller mpc85xx_pci_err: DEV mpc85xx-pci-edac.1.auto (INTERRUPT)
[ 3.159135] genirq: irq 481 uses trigger mode 4; requested 0
[ 3.164088] MPC85xx_edac acquired irq 481 for PCI Err
[ 3.169021] MPC85xx_edac PCI err registered
[ 3.174205] qoriq_cpufreq: qoriq_cpufreq_cpu_init: no clock information
[ 3.179264] qoriq_cpufreq: qoriq_cpufreq_cpu_init: no clock information
[ 3.184193] qoriq_cpufreq: qoriq_cpufreq_cpu_init: no clock information
[ 3.189040] qoriq_cpufreq: qoriq_cpufreq_cpu_init: no clock information
[ 3.193800] qoriq_cpufreq: Freescale QorIQ CPU frequency scaling driver
[ 3.198868] sdhci: Secure Digital Host Controller Interface driver
[ 3.203664] sdhci: Copyright(c) Pierre Ossman
[ 3.208461] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.231139] usb 1-1: new high-speed USB device number 2 using fsl-ehci
[ 3.240151] mmc0: SDHCI controller on ffe114000.sdhc [ffe114000.sdhc] using ADMA
[ 3.245785] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.251235] usbcore: registered new interface driver usbhid
[ 3.256053] usbhid: USB HID core driver
[ 3.261048] Freescale hypervisor management driver
[ 3.265869] fsl-hv: no hypervisor found
[ 3.272218] no UART detected at 0x1
[ 3.277435] snd_hda_intel 0000:01:00.1: Force to snoop mode by module option
[ 3.282581] usbcore: registered new interface driver snd-usb-audio
[ 3.287829] usbcore: registered new interface driver snd-ua101
[ 3.293670] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/platform/ffe200000.pcie/pci0000:00/0000:00:00.0/0000:01:00.1/sound/card1/input0
[ 3.298751] usbcore: registered new interface driver snd-usb-usx2y
[ 3.302139] usb 2-1: new high-speed USB device number 2 using fsl-ehci
[ 3.304145] ata2: Signature Update detected @ 503 msecs
[ 3.304152] ata1: Signature Update detected @ 504 msecs
[ 3.319146] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 3.324439] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.329572] Initializing XFRM netlink socket
[ 3.334958] NET: Registered protocol family 10
[ 3.341590] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.347030] NET: Registered protocol family 17
[ 3.352206] NET: Registered protocol family 15
[ 3.353563] usb 1-1: New USB device found, idVendor=0424, idProduct=2514
[ 3.353566] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.353862] hub 1-1:1.0: USB hub found
[ 3.353936] hub 1-1:1.0: 4 ports detected
[ 3.377758] Key type dns_resolver registered
[ 3.383823] Btrfs loaded, crc32c=crc32c-generic
[ 3.389401] Key type encrypted registered
[ 3.395649] rtc-ds1307 9-006f: setting system clock to 2016-10-19 12:29:32 UTC (1476880172)
[ 3.401110] ALSA device list:
[ 3.406309] #0: Virtual MIDI Card 1
[ 3.411545] #1: HDA ATI HDMI at 0xc10020000 irq 41
[ 3.420547] usb 2-1: New USB device found, idVendor=0424, idProduct=2514
[ 3.425899] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.431460] hub 2-1:1.0: USB hub found
[ 3.436921] hub 2-1:1.0: 4 ports detected
[ 3.464144] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.464147] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.464688] ata1.00: ATA-9: Samsung SSD 840 Series, DXT06B0Q, max UDMA/133
[ 3.464691] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 16/32)
[ 3.464694] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 3.464877] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 3.464882] ata1.00: configured for UDMA/133
[ 3.469758] scsi 0:0:0:0: Direct-Access ATA Samsung SSD 840 6B0Q PQ: 0 ANSI: 5
[ 3.497896] ata2.00: ATAPI: TSSTcorp CDDVDW SH-224FB, SB00, max UDMA/100
[ 3.498435] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.498627] ata1.00: Enabling discard_zeroes_data
[ 3.498654] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB)
[ 3.498820] sd 0:0:0:0: [sda] Write Protect is off
[ 3.498825] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.498878] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.499031] ata1.00: Enabling discard_zeroes_data
[ 3.499487] sda: RDSK (512) sda1 (SWP^@)(res 2 spb 1) sda2 ((res 2 spb 1) sda3 (NTFS)(res 2 spb 1)
[ 3.499901] ata1.00: Enabling discard_zeroes_data
[ 3.500154] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.551268] ata2.00: configured for UDMA/100
[ 3.557984] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW SH-224FB SB00 PQ: 0 ANSI: 5
[ 3.568980] sr 1:0:0:0: [sr0] scsi3-mmc drive: 16x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 3.574533] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 3.580293] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.580383] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.636136] usb 1-1.3: new low-speed USB device number 3 using fsl-ehci
[ 3.732135] usb 2-1.4: new high-speed USB device number 3 using fsl-ehci
[ 3.743927] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c050
[ 3.749512] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.755058] usb 1-1.3: Product: USB-PS/2 Optical Mouse
[ 3.760547] usb 1-1.3: Manufacturer: Logitech
[ 3.770157] input: Logitech USB-PS/2 Optical Mouse as /devices/platform/ffe000000.soc/ffe210000.usb/fsl-ehci.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C050.0001/input/input1
[ 3.776164] hid-generic 0003:046D:C050.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-fsl-ehci.0-1.3/input0
[ 3.832289] random: fast init done
[ 3.839171] usb 2-1.4: New USB device found, idVendor=18a5, idProduct=0216
[ 3.845243] usb 2-1.4: New USB device strings: Mfr=10, Product=11, SerialNumber=3
[ 3.851275] usb 2-1.4: Product: Desktop USB Drive
[ 3.857248] usb 2-1.4: Manufacturer: Verbatim
[ 3.863240] usb 1-1.4: new low-speed USB device number 4 using fsl-ehci
[ 3.869159] usb 2-1.4: SerialNumber: 18A5021600008140
[ 3.875584] usb-storage 2-1.4:1.0: USB Mass Storage device detected
[ 3.881476] scsi host6: usb-storage 2-1.4:1.0
[ 3.893964] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 3.902545] ata4.00: ATA-9: ST1000DX001-1CM162, CC43, max UDMA/133
[ 3.908397] ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 3.919158] ata4.00: configured for UDMA/100
[ 3.925209] scsi 3:0:0:0: Direct-Access ATA ST1000DX001-1CM1 CC43 PQ: 0 ANSI: 5
[ 3.945350] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 3.945378] sd 3:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 3.945383] sd 3:0:0:0: [sdb] 4096-byte physical blocks
[ 3.945507] sd 3:0:0:0: [sdb] Write Protect is off
[ 3.945511] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 3.945559] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.946387] sdb: RDSK (512) sdb1 (NGF^@)(res 2 spb 2) sdb2 (DOS^C)(res 2 spb 2) sdb3 (SWAP)(res 2 spb 8) sdb4 (NGF^@)(res 2 spb 2) sdb5 ((res 2 spb 1) sdb6 ((res 2 spb 1) sdb7 ((res 2 spb 1)
[ 3.947403] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 3.991678] usb 1-1.4: New USB device found, idVendor=04f2, idProduct=0116
[ 3.998145] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.004595] usb 1-1.4: Product: USB Keyboard
[ 4.011018] usb 1-1.4: Manufacturer: CHICONY
[ 4.022673] input: CHICONY USB Keyboard as /devices/platform/ffe000000.soc/ffe210000.usb/fsl-ehci.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:04F2:0116.0002/input/input2
[ 4.081326] hid-generic 0003:04F2:0116.0002: input,hidraw1: USB HID v1.10 Keyboard [CHICONY USB Keyboard] on usb-fsl-ehci.0-1.4/input0
[ 4.293329] ata5: SATA link down (SStatus 0 SControl 310)
[ 4.621327] ata6: SATA link down (SStatus 0 SControl 310)
[ 4.628076] md: Waiting for all devices to be available before autodetect
[ 4.634873] md: If you don't use raid, use raid=noautodetect
[ 4.641875] md: Autodetecting RAID arrays.
[ 4.648632] md: Scanned 0 and added 0 devices.
[ 4.655349] md: autorun ...
[ 4.662076] md: ... autorun DONE.
[ 4.682961] EXT4-fs (sda2): couldn't mount as ext3 due to feature incompatibilities
[ 4.690011] EXT4-fs (sda2): couldn't mount as ext2 due to feature incompatibilities
[ 4.801365] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.808100] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 4.831814] devtmpfs: mounted
[ 4.838611] Freeing unused kernel memory: 384K (c000000000fdf000 - c00000000103f000)
[ 4.845343] This architecture does not have kernel memory protection.
[ 4.896830] scsi 6:0:0:0: Direct-Access SAMSUNG HD154UI PQ: 0 ANSI: 2 CCS
[ 4.904024] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 4.911186] sd 6:0:0:0: [sdc] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[ 4.918557] sd 6:0:0:0: [sdc] Write Protect is off
[ 4.925216] sd 6:0:0:0: [sdc] Mode Sense: 28 00 00 00
[ 4.925809] sd 6:0:0:0: [sdc] No Caching mode page found
[ 4.932400] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 4.949562] sdc: sdc1
[ 4.958434] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 5.409210] systemd[1]: systemd 231 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 5.416365] systemd[1]: Detected architecture ppc64.
[ 5.446320] systemd[1]: Set hostname to <Amigaone>.
[ 5.714916] systemd[1]: lwresd.service: Cannot add dependency job, ignoring: Unit lwresd.service is masked.
[ 5.721863] systemd[1]: dns-clean.service: Cannot add dependency job, ignoring: Unit dns-clean.service is masked.
[ 5.728885] systemd[1]: cgproxy.service: Cannot add dependency job, ignoring: Unit cgproxy.service is masked.
[ 5.735913] systemd[1]: cgmanager.service: Cannot add dependency job, ignoring: Unit cgmanager.service is masked.
[ 5.744748] systemd[1]: Listening on LVM2 poll daemon socket.
[ 5.758453] systemd[1]: Listening on udev Kernel Socket.
[ 5.771909] systemd[1]: Listening on Journal Socket.
[ 6.494972] mmc0: new high speed SDHC card at address 59b4
[ 6.495243] mmcblk0: mmc0:59b4 USD 3.73 GiB
[ 7.405727] random: crng init done
[ 8.337600] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 8.444167] systemd-journald[2140]: Received request to flush runtime journal from PID 1
[ 8.936359] r8169 1000:04:04.0 enP4096p4s4: renamed from eth0
[ 9.070632] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 9.078615] Adding 7807584k swap on /dev/sda1. Priority:-1 extents:1 across:7807584k SSFS
[ 9.389039] cgroup: new mount options do not match the existing superblock, will be ignored
[ 10.590300] IPv6: ADDRCONF(NETDEV_UP): enP4096p4s4: link is not ready
[ 10.599683] r8169 1000:04:04.0 enP4096p4s4: link down
[ 10.599697] r8169 1000:04:04.0 enP4096p4s4: link down
[ 10.599805] IPv6: ADDRCONF(NETDEV_UP): enP4096p4s4: link is not ready
[ 12.125380] r8169 1000:04:04.0 enP4096p4s4: link up
[ 12.125396] IPv6: ADDRCONF(NETDEV_CHANGE): enP4096p4s4: link becomes ready
[ 26.574228] FAT-fs (sdc1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 26.708611] ISO 9660 Extensions: IEEE_P1282
[ 28.745484] radeon 0000:01:00.0: scheduling IB failed (-2).
[ 28.745496] [drm:.radeon_cs_ioctl] *ERROR* Failed to schedule IB !
[ 140.785080] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 140.785099] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 13 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 140.785104] ata2.00: status: { DRDY }
[ 140.785112] ata2: hard resetting link
[ 141.285804] ata2: Hardreset failed, not off-lined 0
[ 141.790047] ata2: Signature Update detected @ 503 msecs
[ 141.950056] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 141.952296] ata2.00: configured for UDMA/100
[ 141.952876] ata2: EH complete
[ 651.757727] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 651.757746] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 9 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 651.757751] ata2.00: status: { DRDY }
[ 651.757759] ata2: hard resetting link
[ 652.258510] ata2: Hardreset failed, not off-lined 0
[ 652.762696] ata2: Signature Update detected @ 503 msecs
[ 652.922704] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 652.924889] ata2.00: configured for UDMA/100
[ 652.925453] ata2: EH complete
[ 1103.850542] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1103.850561] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 8 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1103.850566] ata2.00: status: { DRDY }
[ 1103.850574] ata2: hard resetting link
[ 1104.350515] ata2: Hardreset failed, not off-lined 0
[ 1104.855507] ata2: Signature Update detected @ 503 msecs
[ 1105.015519] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1105.017593] ata2.00: configured for UDMA/100
[ 1105.018075] ata2: EH complete
[ 1317.865254] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 1317.865273] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 3 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 1317.865278] ata2.00: status: { DRDY }
[ 1317.865286] ata2: hard resetting link
[ 1318.364531] ata2: Hardreset failed, not off-lined 0
[ 1318.869478] ata2: Signature Update detected @ 503 msecs
[ 1319.029493] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1319.031554] ata2.00: configured for UDMA/100
[ 1319.032037] ata2: EH complete
[ 2249.184079] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 2249.184099] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 12 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 2249.184104] ata2.00: status: { DRDY }
[ 2249.184111] ata2: hard resetting link
[ 2249.684444] ata2: Hardreset failed, not off-lined 0
[ 2249.686569] ata2: Signature Update detected @ 0 msecs
[ 2249.845059] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2249.848140] ata2.00: configured for UDMA/100
[ 2249.848896] ata2: EH complete
[ 5787.073483] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 5787.073502] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 14 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:03:00:08:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
[ 5787.073507] ata2.00: status: { DRDY }
[ 5787.073515] ata2: hard resetting link
[ 5787.573781] ata2: Hardreset failed, not off-lined 0
[ 5788.078443] ata2: Signature Update detected @ 503 msecs
[ 5788.238447] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 5788.241613] ata2.00: configured for UDMA/100
[ 5788.242124] ata2: EH complete
[ 7311.795765] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 7311.795784] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 9 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 7311.795789] ata2.00: status: { DRDY }
[ 7311.795797] ata2: hard resetting link
[ 7312.296615] ata2: Hardreset failed, not off-lined 0
[ 7312.298742] ata2: Signature Update detected @ 0 msecs
[ 7312.456736] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 7312.459836] ata2.00: configured for UDMA/100
[ 7312.460347] ata2: EH complete
[ 8104.876621] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 8104.876640] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 15 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 8104.876645] ata2.00: status: { DRDY }
[ 8104.876653] ata2: hard resetting link
[ 8105.377438] ata2: Hardreset failed, not off-lined 0
[ 8105.881590] ata2: Signature Update detected @ 503 msecs
[ 8106.041592] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 8106.044742] ata2.00: configured for UDMA/100
[ 8106.045253] ata2: EH complete
[ 9299.873870] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9299.873889] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 9 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9299.873894] ata2.00: status: { DRDY }
[ 9299.873902] ata2: hard resetting link
[ 9300.374677] ata2: Hardreset failed, not off-lined 0
[ 9300.878834] ata2: Signature Update detected @ 503 msecs
[ 9301.038833] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9301.042309] ata2.00: configured for UDMA/100
[ 9301.042838] ata2: EH complete
[ 9749.917813] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9749.917833] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 7 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9749.917838] ata2.00: status: { DRDY }
[ 9749.917845] ata2: hard resetting link
[ 9750.418786] ata2: Hardreset failed, not off-lined 0
[ 9750.922778] ata2: Signature Update detected @ 502 msecs
[ 9751.082788] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9751.085962] ata2.00: configured for UDMA/100
[ 9751.086473] ata2: EH complete
[ 9975.707786] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 9975.707806] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 8 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 9975.707811] ata2.00: status: { DRDY }
[ 9975.707819] ata2: hard resetting link
[ 9976.207743] ata2: Hardreset failed, not off-lined 0
[ 9976.712753] ata2: Signature Update detected @ 503 msecs
[ 9976.872755] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 9976.875870] ata2.00: configured for UDMA/100
[ 9976.876380] ata2: EH complete
[10093.978722] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[10093.978740] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 4 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[10093.978746] ata2.00: status: { DRDY }
[10093.978753] ata2: hard resetting link
[10094.479170] ata2: Hardreset failed, not off-lined 0
[10094.983693] ata2: Signature Update detected @ 503 msecs
[10095.143688] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[10095.146768] ata2.00: configured for UDMA/100
[10095.147279] ata2: EH complete
[11047.826134] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[11047.826154] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 8 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[11047.826159] ata2.00: status: { DRDY }
[11047.826167] ata2: hard resetting link
[11048.326224] ata2: Hardreset failed, not off-lined 0
[11048.831117] ata2: Signature Update detected @ 503 msecs
[11048.991100] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[11048.994241] ata2.00: configured for UDMA/100
[11048.994764] ata2: EH complete
[12238.727445] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[12238.727464] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[12238.727469] ata2.00: status: { DRDY }
[12238.727477] ata2: hard resetting link
[12239.228096] ata2: Hardreset failed, not off-lined 0
[12239.732412] ata2: Signature Update detected @ 503 msecs
[12239.892408] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[12239.895483] ata2.00: configured for UDMA/100
[12239.895994] ata2: EH complete
[13491.069128] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[13491.069146] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 6 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[13491.069151] ata2.00: status: { DRDY }
[13491.069159] ata2: hard resetting link
[13491.569938] ata2: Hardreset failed, not off-lined 0
[13491.572066] ata2: Signature Update detected @ 0 msecs
[13491.730111] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[13491.733248] ata2.00: configured for UDMA/100
[13491.733754] ata2: EH complete
[13556.604604] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[13556.604623] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 9 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[13556.604628] ata2.00: status: { DRDY }
[13556.604636] ata2: hard resetting link
[13557.104939] ata2: Hardreset failed, not off-lined 0
[13557.107066] ata2: Signature Update detected @ 0 msecs
[13557.265578] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[13557.268663] ata2.00: configured for UDMA/100
[13557.269172] ata2: EH complete
[14142.839920] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[14142.839940] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 10 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[14142.839945] ata2.00: status: { DRDY }
[14142.839952] ata2: hard resetting link
[14143.340796] ata2: Hardreset failed, not off-lined 0
[14143.844895] ata2: Signature Update detected @ 502 msecs
[14144.004899] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[14144.008284] ata2.00: configured for UDMA/100
[14144.008801] ata2: EH complete
[14250.871052] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[14250.871071] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 1 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[14250.871076] ata2.00: status: { DRDY }
[14250.871085] ata2: hard resetting link
[14251.371418] ata2: Hardreset failed, not off-lined 0
[14251.877023] ata2: Signature Update detected @ 504 msecs
[14252.036031] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[14252.039512] ata2.00: configured for UDMA/100
[14252.040050] ata2: EH complete
[14707.059412] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[14707.059431] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 2 pio 16392 in
opcode=0x4a 4a 01 00 00 10 00 00 00 08 00res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[14707.059436] ata2.00: status: { DRDY }
[14707.059443] ata2: hard resetting link
[14707.559493] ata2: Hardreset failed, not off-lined 0
[14708.064388] ata2: Signature Update detected @ 503 msecs
[14708.224391] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[14708.227492] ata2.00: configured for UDMA/100
[14708.227998] ata2: EH complete
[-- Attachment #3: lshw.txt --]
[-- Type: text/plain, Size: 12327 bytes --]
lshw:
description: Computer
product: varisys,CYRUS5040
width: 32 bits
capabilities: smp
*-core
description: Motherboard
physical id: 0
*-cpu:0
description: CPU
product: e5500
physical id: 0
bus info: cpu@0
version: 1.2 (pvr 8024 0012)
size: 2200MHz
clock: 800MHz
*-cache
description: L1 Cache
physical id: 0
size: 32KiB
*-cpu:1
description: CPU
product: e5500
physical id: 1
bus info: cpu@1
version: 1.2 (pvr 8024 0012)
size: 2200MHz
clock: 800MHz
*-cache
description: L1 Cache
physical id: 0
size: 32KiB
*-cpu:2
description: CPU
product: e5500
physical id: 2
bus info: cpu@2
version: 1.2 (pvr 8024 0012)
size: 2200MHz
clock: 800MHz
*-cache
description: L1 Cache
physical id: 0
size: 32KiB
*-cpu:3
description: CPU
product: e5500
physical id: 3
bus info: cpu@3
version: 1.2 (pvr 8024 0012)
size: 2200MHz
clock: 800MHz
*-cache
description: L1 Cache
physical id: 0
size: 32KiB
*-memory
description: System memory
physical id: 4
size: 3426MiB
*-processor:0
description: Power PC
product: Freescale Semiconductor Inc
vendor: Freescale Semiconductor Inc
physical id: 5
bus info: pci@0000:00:00.0
version: 21
width: 32 bits
clock: 33MHz
capabilities: pm pciexpress bus_master cap_list
configuration: driver=pcieport latency=0
resources: irq:482 ioport:0(size=65536) memory:c00000000-c1fffffff
*-display
description: VGA compatible controller
product: Whistler LE [Radeon HD 6610M/7610M]
vendor: Advanced Micro Devices, Inc. [AMD/ATI]
physical id: 6
bus info: pci@0000:01:00.0
version: 00
width: 64 bits
clock: 33MHz
capabilities: pm pciexpress msi vga_controller bus_master cap_list rom
configuration: driver=radeon latency=0
resources: irq:27 memory:c00000000-c0fffffff memory:c10000000-c1001ffff ioport:1000(size=256) memory:c10040000-c1005ffff
*-multimedia
description: Audio device
product: Turks HDMI Audio [Radeon HD 6500/6600 / 6700M Series]
vendor: Advanced Micro Devices, Inc. [AMD/ATI]
physical id: 0.1
bus info: pci@0000:01:00.1
version: 00
width: 64 bits
clock: 33MHz
capabilities: pm pciexpress msi bus_master cap_list
configuration: driver=snd_hda_intel latency=0
resources: irq:41 memory:c10020000-c10023fff
*-processor:1
description: Power PC
product: Freescale Semiconductor Inc
vendor: Freescale Semiconductor Inc
physical id: 7
bus info: pci@1000:00:00.0
version: 21
width: 32 bits
clock: 33MHz
capabilities: pm pciexpress bus_master cap_list
configuration: driver=pcieport latency=0
resources: irq:481 ioport:0(size=65536) memory:c20000000-c3fffffff
*-pci
description: PCI bridge
product: Integrated Device Technology, Inc. [IDT]
vendor: Integrated Device Technology, Inc. [IDT]
physical id: 100
bus info: pci@1000:01:00.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci pciexpress pm normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:0 ioport:1000(size=4096) memory:c20000000-c200fffff
*-pci:0
description: PCI bridge
product: Integrated Device Technology, Inc. [IDT]
vendor: Integrated Device Technology, Inc. [IDT]
physical id: 1
bus info: pci@1000:02:01.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci pciexpress pm msi normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:20 ioport:1000(size=4096) memory:c20000000-c200fffff
*-pci
description: PCI bridge
product: PI7C9X111SL PCIe-to-PCI Reversible Bridge
vendor: Pericom Semiconductor
physical id: 0
bus info: pci@1000:03:00.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci pcix pm pciexpress msi normal_decode bus_master cap_list
resources: ioport:1000(size=4096) memory:c20000000-c200fffff
*-network
description: Ethernet interface
product: RTL8169 PCI Gigabit Ethernet Controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 4
bus info: pci@1000:04:04.0
logical name: enP4096p4s4
version: 10
serial: 60:e3:27:05:53:20
size: 100Mbit/s
capacity: 1Gbit/s
width: 32 bits
clock: 66MHz
capabilities: bus_master rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.11 latency=64 link=yes maxlatency=64 mingnt=32 multicast=yes port=MII speed=100Mbit/s
resources: irq:18 ioport:1000(size=256) memory:c20000000-c200000ff memory:c20020000-c2003ffff
*-storage
description: RAID bus controller
product: SiI 3114 [SATALink/SATARaid] Serial ATA Controller
vendor: Silicon Image, Inc.
physical id: 5
bus info: pci@1000:04:05.0
version: 02
width: 32 bits
clock: 66MHz
capabilities: storage pm bus_master cap_list rom
configuration: driver=sata_sil latency=128
resources: irq:19 ioport:1100(size=8) ioport:1108(size=4) ioport:1110(size=8) ioport:1118(size=4) ioport:1120(size=16) memory:c20000400-c200007ff memory:c20080000-c200fffff
*-pci:1
description: PCI bridge
product: Integrated Device Technology, Inc. [IDT]
vendor: Integrated Device Technology, Inc. [IDT]
physical id: 2
bus info: pci@1000:02:02.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci pciexpress pm msi normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:21
*-pci:2
description: PCI bridge
product: Integrated Device Technology, Inc. [IDT]
vendor: Integrated Device Technology, Inc. [IDT]
physical id: 3
bus info: pci@1000:02:03.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci pciexpress pm msi normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:22
*-pci:3
description: PCI bridge
product: Integrated Device Technology, Inc. [IDT]
vendor: Integrated Device Technology, Inc. [IDT]
physical id: 8
bus info: pci@1000:02:08.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci pciexpress pm msi normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:23
*-pci:4
description: PCI bridge
product: Integrated Device Technology, Inc. [IDT]
vendor: Integrated Device Technology, Inc. [IDT]
physical id: 10
bus info: pci@1000:02:10.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pci pciexpress pm msi normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:26
*-scsi:0
physical id: 8
logical name: scsi0
capabilities: emulated
*-disk
description: ATA Disk
product: Samsung SSD 840
physical id: 0.0.0
bus info: scsi@0:0.0.0
logical name: /dev/sda
version: 6B0Q
serial: S14CNEBCB16572V
size: 111GiB (120GB)
configuration: ansiversion=5 logicalsectorsize=512 sectorsize=512
*-scsi:1
physical id: 9
logical name: scsi1
capabilities: emulated
*-cdrom
description: DVD-RAM writer
product: CDDVDW SH-224FB
vendor: TSSTcorp
physical id: 0.0.0
bus info: scsi@1:0.0.0
logical name: /dev/cdrom
logical name: /dev/cdrw
logical name: /dev/dvd
logical name: /dev/dvdrw
logical name: /dev/sr0
logical name: /media/amigaone/BOOT
version: SB00
serial: [
capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram
configuration: ansiversion=5 mount.fstype=iso9660 mount.options=ro,nosuid,nodev,relatime,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500 state=mounted status=ready
*-medium
physical id: 0
logical name: /dev/cdrom
logical name: /media/amigaone/BOOT
configuration: mount.fstype=iso9660 mount.options=ro,nosuid,nodev,relatime,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500 state=mounted
*-scsi:2
physical id: a
logical name: scsi3
capabilities: emulated
*-disk
description: ATA Disk
product: ST1000DX001-1CM1
vendor: Seagate
physical id: 0.0.0
bus info: scsi@3:0.0.0
logical name: /dev/sdb
version: CC43
serial: Z1D9K8LY
size: 931GiB (1TB)
configuration: ansiversion=5 logicalsectorsize=512 sectorsize=4096
*-scsi:3
physical id: b
bus info: usb@2:1.4
logical name: scsi6
capabilities: emulated scsi-host
configuration: driver=usb-storage
*-disk
description: SCSI Disk
product: HD154UI
vendor: SAMSUNG
physical id: 0.0.0
bus info: scsi@6:0.0.0
logical name: /dev/sdc
serial: 801130168383
size: 1397GiB (1500GB)
capabilities: partitioned partitioned:dos
configuration: ansiversion=2 logicalsectorsize=512 sectorsize=512 signature=0cd096ae
*-volume
description: Windows FAT volume
vendor: MSWIN4.1
physical id: 1
bus info: scsi@6:0.0.0,1
logical name: /dev/sdc1
logical name: /media/amigaone/VERBATIM
version: FAT32
serial: 0000-0000
size: 1397GiB
capacity: 1397GiB
capabilities: primary fat initialized
configuration: FATs=2 filesystem=fat label=VERBATIM mount.fstype=vfat mount.options=rw,nosuid,nodev,relatime,uid=1000,gid=1000,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,showexec,utf8,flush,errors=remount-ro state=mounted
*-network DISABLED
description: Ethernet interface
physical id: 1
logical name: dummy0
serial: b2:ee:2c:7d:19:ae
capabilities: ethernet physical
configuration: broadcast=yes driver=dummy driverversion=1.0
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 3/3] corenet: Switch to of_platform_default_populate
2016-10-23 23:48 ` [PATCH 3/3] corenet: Switch to of_platform_default_populate Andy Fleming
@ 2016-10-24 21:43 ` Scott Wood
0 siblings, 0 replies; 7+ messages in thread
From: Scott Wood @ 2016-10-24 21:43 UTC (permalink / raw)
To: Andy Fleming, linuxppc-dev, scottwood; +Cc: aperez
On 10/23/2016 06:48 PM, Andy Fleming wrote:=0A=
> Many of the embedded powerpc boards use an array of device names=0A=
> to register the devices from the device tree. Instead, we can use=0A=
> of_platform_default_populate(), which will iterate through all the root n=
odes and register them.=0A=
> =0A=
> Signed-off-by: Andy Fleming <afleming@gmail.com>=0A=
> ---=0A=
> This is necessary to enable the gpio power/reset pins on the Cyrus board.=
=0A=
> =0A=
> I have confirmed that the PCI devices are registered and that the power/r=
eset=0A=
> drivers are registered (and functional). I also tested USB, and saw the=
=0A=
> onboard MMC card report in, so some of the SoC devices are definitely the=
re.=0A=
> =0A=
> If this doesn't break the other corenet boards, I'd be happy to make the=
=0A=
> same change for the other powerpc boards.=0A=
> =0A=
> arch/powerpc/platforms/85xx/corenet_generic.c | 49 +--------------------=
------=0A=
> 1 file changed, 1 insertion(+), 48 deletions(-)=0A=
> =0A=
> diff --git a/arch/powerpc/platforms/85xx/corenet_generic.c b/arch/powerpc=
/platforms/85xx/corenet_generic.c=0A=
> index 1179115..6347f20 100644=0A=
> --- a/arch/powerpc/platforms/85xx/corenet_generic.c=0A=
> +++ b/arch/powerpc/platforms/85xx/corenet_generic.c=0A=
> @@ -83,56 +83,9 @@ void __init corenet_gen_setup_arch(void)=0A=
> mpc85xx_qe_init();=0A=
> }=0A=
> =0A=
> -static const struct of_device_id of_device_ids[] =3D {=0A=
> - {=0A=
> - .compatible =3D "simple-bus"=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "mdio-mux-gpio"=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "fsl,fpga-ngpixis"=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "fsl,fpga-qixis"=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "fsl,srio",=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "fsl,p4080-pcie",=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "fsl,qoriq-pcie-v2.2",=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "fsl,qoriq-pcie-v2.3",=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "fsl,qoriq-pcie-v2.4",=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "fsl,qoriq-pcie-v3.0",=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "fsl,qe",=0A=
> - },=0A=
> - {=0A=
> - .compatible =3D "fsl,fman",=0A=
> - },=0A=
> - /* The following two are for the Freescale hypervisor */=0A=
> - {=0A=
> - .name =3D "hypervisor",=0A=
> - },=0A=
> - {=0A=
> - .name =3D "handles",=0A=
> - },=0A=
> - {}=0A=
> -};=0A=
> -=0A=
> int __init corenet_gen_publish_devices(void)=0A=
> {=0A=
> - return of_platform_bus_probe(NULL, of_device_ids, NULL);=0A=
> + return of_platform_default_populate(NULL, NULL, NULL);=0A=
> }=0A=
=0A=
I think we still need to specify some of these nodes. Switching from=0A=
probe to populate will take care of probing device nodes under root=0A=
without listing each one, but it won't treat those nodes as buses unless=0A=
they have "simple-bus" or otherwise match the probe list.=0A=
=0A=
-Scott=0A=
=0A=
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [v2,1/3] cyrus: Add poweroff/reset support
2016-10-23 23:48 [PATCH v2 1/3] cyrus: Add poweroff/reset support Andy Fleming
2016-10-23 23:48 ` [PATCH 2/3] 85xx: Enable gpio power/reset driver Andy Fleming
2016-10-23 23:48 ` [PATCH 3/3] corenet: Switch to of_platform_default_populate Andy Fleming
@ 2016-11-23 7:00 ` Scott Wood
2 siblings, 0 replies; 7+ messages in thread
From: Scott Wood @ 2016-11-23 7:00 UTC (permalink / raw)
To: Andy Fleming; +Cc: linuxppc-dev, scottwood, aperez
On Sun, Oct 23, 2016 at 06:48:37PM -0500, Andy Fleming wrote:
> Cyrus uses GPIOs to complete board shutdown/reset.
> Add nodes to indicate that support to the device tree.
>
> Signed-off-by: Andy Fleming <afleming@gmail.com>
> ---
> v2: No changes
>
> arch/powerpc/boot/dts/fsl/cyrus_p5020.dts | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
> diff --git a/arch/powerpc/boot/dts/fsl/cyrus_p5020.dts b/arch/powerpc/boot/dts/fsl/cyrus_p5020.dts
> index c603390..e417aaa 100644
> --- a/arch/powerpc/boot/dts/fsl/cyrus_p5020.dts
> +++ b/arch/powerpc/boot/dts/fsl/cyrus_p5020.dts
> @@ -150,6 +150,17 @@
> 0 0x00010000>;
> };
> };
> +
> + gpio-poweroff {
> + compatible = "gpio-poweroff";
> + gpios = <&gpio0 3 1>;
> + };
> +
> + gpio-restart {
> + compatible = "gpio-restart";
> + gpios = <&gpio0 2 1>;
Please use tabs, not spaces.
> + };
> +
> };
Don't put a blank line here.
-Scott
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: 85xx: Enable gpio power/reset driver
2016-10-23 23:48 ` [PATCH 2/3] 85xx: Enable gpio power/reset driver Andy Fleming
2016-10-24 16:16 ` Cyrus_5040.dts Misisng luigi burdo
@ 2017-07-05 15:37 ` Darren Stevens
1 sibling, 0 replies; 7+ messages in thread
From: Darren Stevens @ 2017-07-05 15:37 UTC (permalink / raw)
To: linuxppc-dev, scottwood; +Cc: aperez
Hello Scott
On 23/10/2016, Andy Fleming wrote:
> These config changes build:
> drivers/power/reset/gpio-poweroff.c
> drivers/power/reset/gpio-restart.c
>
> Signed-off-by: Andy Fleming <afleming@gmail.com>
> ---
> arch/powerpc/configs/fsl-emb-nonhw.config | 6 ++++++
> 1 file changed, 6 insertions(+)
Is there any news on when these patches will be merged? We have end-users with
Cyrus boards now, and would like to provide them with a mainline kernel that
can power-off/reset the board.
Thanks
Darren
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2017-07-05 16:43 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-10-23 23:48 [PATCH v2 1/3] cyrus: Add poweroff/reset support Andy Fleming
2016-10-23 23:48 ` [PATCH 2/3] 85xx: Enable gpio power/reset driver Andy Fleming
2016-10-24 16:16 ` Cyrus_5040.dts Misisng luigi burdo
2017-07-05 15:37 ` 85xx: Enable gpio power/reset driver Darren Stevens
2016-10-23 23:48 ` [PATCH 3/3] corenet: Switch to of_platform_default_populate Andy Fleming
2016-10-24 21:43 ` Scott Wood
2016-11-23 7:00 ` [v2,1/3] cyrus: Add poweroff/reset support Scott Wood
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.