[PATCH v4 0/7] add NS2 support to bgmac

[PATCH v4 0/7] add NS2 support to bgmac

[Jon Mason]

Changes in v4:
* Actually send out the lane swap binding doc patch (Per Scott Branden)
* Remove unused #define (Per Andrew Lunn)


Changes in v3:
* Clean-up the bgmac DT binding doc (per Rob Herring)
* Document the lane swap binding and make it generic (Per Andrew Lunn)


Changes in v2:
* Remove the PHY power-on (per Andrew Lunn)
* Misc PHY clean-ups regarding comments and #defines (per Andrew Lunn)
  This results on none of the original PHY code from Vikas being
  present.  So, I'm removing him as an author and giving him
  "Inspired-by" credit.
* Move PHY lane swapping to PHY driver (per Andrew Lunn and Florian
  Fainelli)
* Remove bgmac sleep (per Florian Fainelli)
* Re-add bgmac chip reset (per Florian Fainelli and Ray Jui)
* Rebased on latest net-next
* Added patch for bcm54xx_auxctl_read, which is used in the BCM54810


Add support for the amac found in the Broadcom Northstar2 SoC to the
bgmac driver.  This necessitates adding support to connect to an
externally defined phy (as described in the device tree) in the driver.
These phy changes are in addition to the changes necessary to get NS2
working.


Jon Mason (7):
  net: phy: broadcom: add bcm54xx_auxctl_read
  Documentation: devicetree: add PHY lane swap binding
  net: phy: broadcom: Add BCM54810 PHY entry
  Documentation: devicetree: net: add NS2 bindings to amac
  net: ethernet: bgmac: device tree phy enablement
  net: ethernet: bgmac: add NS2 support
  arm64: dts: NS2: add AMAC ethernet support

 .../devicetree/bindings/net/brcm,amac.txt          |  16 ++--
 Documentation/devicetree/bindings/net/phy.txt      |   3 +
 arch/arm64/boot/dts/broadcom/ns2-svk.dts           |   5 ++
 arch/arm64/boot/dts/broadcom/ns2.dtsi              |  12 +++
 drivers/net/ethernet/broadcom/bgmac-bcma.c         |  48 ++++++++++
 drivers/net/ethernet/broadcom/bgmac-platform.c     | 100 ++++++++++++++++++++-
 drivers/net/ethernet/broadcom/bgmac.c              |  55 ++----------
 drivers/net/ethernet/broadcom/bgmac.h              |   8 ++
 drivers/net/phy/Kconfig                            |   2 +-
 drivers/net/phy/broadcom.c                         |  68 +++++++++++++-
 include/linux/brcmphy.h                            |  10 +++
 11 files changed, 270 insertions(+), 57 deletions(-)

-- 
2.7.4

[PATCH v4 0/7] add NS2 support to bgmac

[Jon Mason]

Changes in v4:
* Actually send out the lane swap binding doc patch (Per Scott Branden)
* Remove unused #define (Per Andrew Lunn)


Changes in v3:
* Clean-up the bgmac DT binding doc (per Rob Herring)
* Document the lane swap binding and make it generic (Per Andrew Lunn)


Changes in v2:
* Remove the PHY power-on (per Andrew Lunn)
* Misc PHY clean-ups regarding comments and #defines (per Andrew Lunn)
  This results on none of the original PHY code from Vikas being
  present.  So, I'm removing him as an author and giving him
  "Inspired-by" credit.
* Move PHY lane swapping to PHY driver (per Andrew Lunn and Florian
  Fainelli)
* Remove bgmac sleep (per Florian Fainelli)
* Re-add bgmac chip reset (per Florian Fainelli and Ray Jui)
* Rebased on latest net-next
* Added patch for bcm54xx_auxctl_read, which is used in the BCM54810


Add support for the amac found in the Broadcom Northstar2 SoC to the
bgmac driver.  This necessitates adding support to connect to an
externally defined phy (as described in the device tree) in the driver.
These phy changes are in addition to the changes necessary to get NS2
working.


Jon Mason (7):
  net: phy: broadcom: add bcm54xx_auxctl_read
  Documentation: devicetree: add PHY lane swap binding
  net: phy: broadcom: Add BCM54810 PHY entry
  Documentation: devicetree: net: add NS2 bindings to amac
  net: ethernet: bgmac: device tree phy enablement
  net: ethernet: bgmac: add NS2 support
  arm64: dts: NS2: add AMAC ethernet support

 .../devicetree/bindings/net/brcm,amac.txt          |  16 ++--
 Documentation/devicetree/bindings/net/phy.txt      |   3 +
 arch/arm64/boot/dts/broadcom/ns2-svk.dts           |   5 ++
 arch/arm64/boot/dts/broadcom/ns2.dtsi              |  12 +++
 drivers/net/ethernet/broadcom/bgmac-bcma.c         |  48 ++++++++++
 drivers/net/ethernet/broadcom/bgmac-platform.c     | 100 ++++++++++++++++++++-
 drivers/net/ethernet/broadcom/bgmac.c              |  55 ++----------
 drivers/net/ethernet/broadcom/bgmac.h              |   8 ++
 drivers/net/phy/Kconfig                            |   2 +-
 drivers/net/phy/broadcom.c                         |  68 +++++++++++++-
 include/linux/brcmphy.h                            |  10 +++
 11 files changed, 270 insertions(+), 57 deletions(-)

-- 
2.7.4

[PATCH v4 1/7] net: phy: broadcom: add bcm54xx_auxctl_read

[Jon Mason]

Add a helper function to read the AUXCTL register for the BCM54xx.  This
mirrors the bcm54xx_auxctl_write function already present in the code.

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 drivers/net/phy/broadcom.c | 10 ++++++++++
 include/linux/brcmphy.h    |  1 +
 2 files changed, 11 insertions(+)

diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 583ef8a..3a64b3d 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -30,6 +30,16 @@ MODULE_DESCRIPTION("Broadcom PHY driver");
 MODULE_AUTHOR("Maciej W. Rozycki");
 MODULE_LICENSE("GPL");
 
+static int bcm54xx_auxctl_read(struct phy_device *phydev, u16 regnum)
+{
+	/* The register must be written to both the Shadow Register Select and
+	 * the Shadow Read Register Selector
+	 */
+	phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum |
+		  regnum << MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT);
+	return phy_read(phydev, MII_BCM54XX_AUX_CTL);
+}
+
 static int bcm54xx_auxctl_write(struct phy_device *phydev, u16 regnum, u16 val)
 {
 	return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 60def78..0ed6691 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -110,6 +110,7 @@
 #define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX	0x0200
 #define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
+#define MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT	12
 
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MASK	0x0007
 
-- 
2.7.4

[PATCH v4 1/7] net: phy: broadcom: add bcm54xx_auxctl_read

[Jon Mason]

Add a helper function to read the AUXCTL register for the BCM54xx.  This
mirrors the bcm54xx_auxctl_write function already present in the code.

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 drivers/net/phy/broadcom.c | 10 ++++++++++
 include/linux/brcmphy.h    |  1 +
 2 files changed, 11 insertions(+)

diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 583ef8a..3a64b3d 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -30,6 +30,16 @@ MODULE_DESCRIPTION("Broadcom PHY driver");
 MODULE_AUTHOR("Maciej W. Rozycki");
 MODULE_LICENSE("GPL");
 
+static int bcm54xx_auxctl_read(struct phy_device *phydev, u16 regnum)
+{
+	/* The register must be written to both the Shadow Register Select and
+	 * the Shadow Read Register Selector
+	 */
+	phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum |
+		  regnum << MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT);
+	return phy_read(phydev, MII_BCM54XX_AUX_CTL);
+}
+
 static int bcm54xx_auxctl_write(struct phy_device *phydev, u16 regnum, u16 val)
 {
 	return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 60def78..0ed6691 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -110,6 +110,7 @@
 #define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX	0x0200
 #define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
+#define MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT	12
 
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MASK	0x0007
 
-- 
2.7.4

[PATCH v4 1/7] net: phy: broadcom: add bcm54xx_auxctl_read

[Jon Mason]

Add a helper function to read the AUXCTL register for the BCM54xx.  This
mirrors the bcm54xx_auxctl_write function already present in the code.

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 drivers/net/phy/broadcom.c | 10 ++++++++++
 include/linux/brcmphy.h    |  1 +
 2 files changed, 11 insertions(+)

diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 583ef8a..3a64b3d 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -30,6 +30,16 @@ MODULE_DESCRIPTION("Broadcom PHY driver");
 MODULE_AUTHOR("Maciej W. Rozycki");
 MODULE_LICENSE("GPL");
 
+static int bcm54xx_auxctl_read(struct phy_device *phydev, u16 regnum)
+{
+	/* The register must be written to both the Shadow Register Select and
+	 * the Shadow Read Register Selector
+	 */
+	phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum |
+		  regnum << MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT);
+	return phy_read(phydev, MII_BCM54XX_AUX_CTL);
+}
+
 static int bcm54xx_auxctl_write(struct phy_device *phydev, u16 regnum, u16 val)
 {
 	return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 60def78..0ed6691 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -110,6 +110,7 @@
 #define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX	0x0200
 #define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
+#define MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT	12
 
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MASK	0x0007
 
-- 
2.7.4

[PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Jon Mason]

Add the documentation for PHY lane swapping.  This is a boolean entry to
notify the phy device drivers that the TX/RX lanes need to be swapped.

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 Documentation/devicetree/bindings/net/phy.txt | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
index bc1c3c8..3dce607 100644
--- a/Documentation/devicetree/bindings/net/phy.txt
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -35,6 +35,9 @@ Optional Properties:
 - broken-turn-around: If set, indicates the PHY device does not correctly
   release the turn around line low at the end of a MDIO transaction.
 
+- enet-phy-lane-swap: If set, indicates the PHY device requires swapping the
+  TX/RX lanes to function properly.
+
 Example:
 
 ethernet-phy@0 {
-- 
2.7.4

[PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Jon Mason]

Add the documentation for PHY lane swapping.  This is a boolean entry to
notify the phy device drivers that the TX/RX lanes need to be swapped.

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 Documentation/devicetree/bindings/net/phy.txt | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
index bc1c3c8..3dce607 100644
--- a/Documentation/devicetree/bindings/net/phy.txt
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -35,6 +35,9 @@ Optional Properties:
 - broken-turn-around: If set, indicates the PHY device does not correctly
   release the turn around line low at the end of a MDIO transaction.
 
+- enet-phy-lane-swap: If set, indicates the PHY device requires swapping the
+  TX/RX lanes to function properly.
+
 Example:
 
 ethernet-phy at 0 {
-- 
2.7.4

[PATCH v4 3/7] net: phy: broadcom: Add BCM54810 PHY entry

[Jon Mason]

The BCM54810 PHY requires some semi-unique configuration, which results
in some additional configuration in addition to the standard config.
Also, some users of the BCM54810 require the PHY lanes to be swapped.
Since there is no way to detect this, add a device tree query to see if
it is applicable.

Inspired-by: Vikas Soni <vsoni@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 drivers/net/phy/Kconfig    |  2 +-
 drivers/net/phy/broadcom.c | 58 +++++++++++++++++++++++++++++++++++++++++++++-
 include/linux/brcmphy.h    |  9 +++++++
 3 files changed, 67 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 45f68ea..31967ca 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -217,7 +217,7 @@ config BROADCOM_PHY
 	select BCM_NET_PHYLIB
 	---help---
 	  Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
-	  BCM5481 and BCM5482 PHYs.
+	  BCM5481, BCM54810 and BCM5482 PHYs.
 
 config CICADA_PHY
 	tristate "Cicada PHYs"
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 3a64b3d..b1e32e9 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -18,7 +18,7 @@
 #include <linux/module.h>
 #include <linux/phy.h>
 #include <linux/brcmphy.h>
-
+#include <linux/of.h>
 
 #define BRCM_PHY_MODEL(phydev) \
 	((phydev)->drv->phy_id & (phydev)->drv->phy_id_mask)
@@ -45,6 +45,34 @@ static int bcm54xx_auxctl_write(struct phy_device *phydev, u16 regnum, u16 val)
 	return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
 }
 
+static int bcm54810_config(struct phy_device *phydev)
+{
+	int rc, val;
+
+	val = bcm_phy_read_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL);
+	val &= ~BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN;
+	rc = bcm_phy_write_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL,
+			       val);
+	if (rc < 0)
+		return rc;
+
+	val = bcm54xx_auxctl_read(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
+	val &= ~MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN;
+	val |= MII_BCM54XX_AUXCTL_MISC_WREN;
+	rc = bcm54xx_auxctl_write(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC,
+				  val);
+	if (rc < 0)
+		return rc;
+
+	val = bcm_phy_read_shadow(phydev, BCM54810_SHD_CLK_CTL);
+	val &= ~BCM54810_SHD_CLK_CTL_GTXCLK_EN;
+	rc = bcm_phy_write_shadow(phydev, BCM54810_SHD_CLK_CTL, val);
+	if (rc < 0)
+		return rc;
+
+	return 0;
+}
+
 /* Needs SMDSP clock enabled via bcm54xx_phydsp_config() */
 static int bcm50610_a0_workaround(struct phy_device *phydev)
 {
@@ -217,6 +245,12 @@ static int bcm54xx_config_init(struct phy_device *phydev)
 	    (phydev->dev_flags & PHY_BRCM_AUTO_PWRDWN_ENABLE))
 		bcm54xx_adjust_rxrefclk(phydev);
 
+	if (BRCM_PHY_MODEL(phydev) == PHY_ID_BCM54810) {
+		err = bcm54810_config(phydev);
+		if (err)
+			return err;
+	}
+
 	bcm54xx_phydsp_config(phydev);
 
 	return 0;
@@ -314,6 +348,7 @@ static int bcm5482_read_status(struct phy_device *phydev)
 
 static int bcm5481_config_aneg(struct phy_device *phydev)
 {
+	struct device_node *np = phydev->mdio.dev.of_node;
 	int ret;
 
 	/* Aneg firsly. */
@@ -344,6 +379,14 @@ static int bcm5481_config_aneg(struct phy_device *phydev)
 		phy_write(phydev, 0x18, reg);
 	}
 
+	if (of_property_read_bool(np, "enet-phy-lane-swap")) {
+		/* Lane Swap - Undocumented register...magic! */
+		ret = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_SEL_ER + 0x9,
+					0x11B);
+		if (ret < 0)
+			return ret;
+	}
+
 	return ret;
 }
 
@@ -578,6 +621,18 @@ static struct phy_driver broadcom_drivers[] = {
 	.ack_interrupt	= bcm_phy_ack_intr,
 	.config_intr	= bcm_phy_config_intr,
 }, {
+	.phy_id         = PHY_ID_BCM54810,
+	.phy_id_mask    = 0xfffffff0,
+	.name           = "Broadcom BCM54810",
+	.features       = PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
+	.config_init    = bcm54xx_config_init,
+	.config_aneg    = bcm5481_config_aneg,
+	.read_status    = genphy_read_status,
+	.ack_interrupt  = bcm_phy_ack_intr,
+	.config_intr    = bcm_phy_config_intr,
+}, {
 	.phy_id		= PHY_ID_BCM5482,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5482",
@@ -661,6 +716,7 @@ static struct mdio_device_id __maybe_unused broadcom_tbl[] = {
 	{ PHY_ID_BCM54616S, 0xfffffff0 },
 	{ PHY_ID_BCM5464, 0xfffffff0 },
 	{ PHY_ID_BCM5481, 0xfffffff0 },
+	{ PHY_ID_BCM54810, 0xfffffff0 },
 	{ PHY_ID_BCM5482, 0xfffffff0 },
 	{ PHY_ID_BCM50610, 0xfffffff0 },
 	{ PHY_ID_BCM50610M, 0xfffffff0 },
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 0ed6691..848dc50 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -13,6 +13,7 @@
 #define PHY_ID_BCM5241			0x0143bc30
 #define PHY_ID_BCMAC131			0x0143bc70
 #define PHY_ID_BCM5481			0x0143bca0
+#define PHY_ID_BCM54810			0x03625d00
 #define PHY_ID_BCM5482			0x0143bcb0
 #define PHY_ID_BCM5411			0x00206070
 #define PHY_ID_BCM5421			0x002060e0
@@ -56,6 +57,7 @@
 #define PHY_BRCM_EXT_IBND_TX_ENABLE	0x00002000
 #define PHY_BRCM_CLEAR_RGMII_MODE	0x00004000
 #define PHY_BRCM_DIS_TXCRXC_NOENRGY	0x00008000
+
 /* Broadcom BCM7xxx specific workarounds */
 #define PHY_BRCM_7XXX_REV(x)		(((x) >> 8) & 0xff)
 #define PHY_BRCM_7XXX_PATCH(x)		((x) & 0xff)
@@ -111,6 +113,7 @@
 #define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
 #define MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT	12
+#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN	(1 << 8)
 
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MASK	0x0007
 
@@ -192,6 +195,12 @@
 #define BCM5482_SSD_SGMII_SLAVE_EN	0x0002	/* Slave mode enable */
 #define BCM5482_SSD_SGMII_SLAVE_AD	0x0001	/* Slave auto-detection */
 
+/* BCM54810 Registers */
+#define BCM54810_EXP_BROADREACH_LRE_MISC_CTL	(MII_BCM54XX_EXP_SEL_ER + 0x90)
+#define BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN	(1 << 0)
+#define BCM54810_SHD_CLK_CTL			0x3
+#define BCM54810_SHD_CLK_CTL_GTXCLK_EN		(1 << 9)
+
 
 /*****************************************************************************/
 /* Fast Ethernet Transceiver definitions. */
-- 
2.7.4

[PATCH v4 3/7] net: phy: broadcom: Add BCM54810 PHY entry

[Jon Mason]

The BCM54810 PHY requires some semi-unique configuration, which results
in some additional configuration in addition to the standard config.
Also, some users of the BCM54810 require the PHY lanes to be swapped.
Since there is no way to detect this, add a device tree query to see if
it is applicable.

Inspired-by: Vikas Soni <vsoni@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 drivers/net/phy/Kconfig    |  2 +-
 drivers/net/phy/broadcom.c | 58 +++++++++++++++++++++++++++++++++++++++++++++-
 include/linux/brcmphy.h    |  9 +++++++
 3 files changed, 67 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 45f68ea..31967ca 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -217,7 +217,7 @@ config BROADCOM_PHY
 	select BCM_NET_PHYLIB
 	---help---
 	  Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
-	  BCM5481 and BCM5482 PHYs.
+	  BCM5481, BCM54810 and BCM5482 PHYs.
 
 config CICADA_PHY
 	tristate "Cicada PHYs"
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 3a64b3d..b1e32e9 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -18,7 +18,7 @@
 #include <linux/module.h>
 #include <linux/phy.h>
 #include <linux/brcmphy.h>
-
+#include <linux/of.h>
 
 #define BRCM_PHY_MODEL(phydev) \
 	((phydev)->drv->phy_id & (phydev)->drv->phy_id_mask)
@@ -45,6 +45,34 @@ static int bcm54xx_auxctl_write(struct phy_device *phydev, u16 regnum, u16 val)
 	return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
 }
 
+static int bcm54810_config(struct phy_device *phydev)
+{
+	int rc, val;
+
+	val = bcm_phy_read_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL);
+	val &= ~BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN;
+	rc = bcm_phy_write_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL,
+			       val);
+	if (rc < 0)
+		return rc;
+
+	val = bcm54xx_auxctl_read(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
+	val &= ~MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN;
+	val |= MII_BCM54XX_AUXCTL_MISC_WREN;
+	rc = bcm54xx_auxctl_write(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC,
+				  val);
+	if (rc < 0)
+		return rc;
+
+	val = bcm_phy_read_shadow(phydev, BCM54810_SHD_CLK_CTL);
+	val &= ~BCM54810_SHD_CLK_CTL_GTXCLK_EN;
+	rc = bcm_phy_write_shadow(phydev, BCM54810_SHD_CLK_CTL, val);
+	if (rc < 0)
+		return rc;
+
+	return 0;
+}
+
 /* Needs SMDSP clock enabled via bcm54xx_phydsp_config() */
 static int bcm50610_a0_workaround(struct phy_device *phydev)
 {
@@ -217,6 +245,12 @@ static int bcm54xx_config_init(struct phy_device *phydev)
 	    (phydev->dev_flags & PHY_BRCM_AUTO_PWRDWN_ENABLE))
 		bcm54xx_adjust_rxrefclk(phydev);
 
+	if (BRCM_PHY_MODEL(phydev) == PHY_ID_BCM54810) {
+		err = bcm54810_config(phydev);
+		if (err)
+			return err;
+	}
+
 	bcm54xx_phydsp_config(phydev);
 
 	return 0;
@@ -314,6 +348,7 @@ static int bcm5482_read_status(struct phy_device *phydev)
 
 static int bcm5481_config_aneg(struct phy_device *phydev)
 {
+	struct device_node *np = phydev->mdio.dev.of_node;
 	int ret;
 
 	/* Aneg firsly. */
@@ -344,6 +379,14 @@ static int bcm5481_config_aneg(struct phy_device *phydev)
 		phy_write(phydev, 0x18, reg);
 	}
 
+	if (of_property_read_bool(np, "enet-phy-lane-swap")) {
+		/* Lane Swap - Undocumented register...magic! */
+		ret = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_SEL_ER + 0x9,
+					0x11B);
+		if (ret < 0)
+			return ret;
+	}
+
 	return ret;
 }
 
@@ -578,6 +621,18 @@ static struct phy_driver broadcom_drivers[] = {
 	.ack_interrupt	= bcm_phy_ack_intr,
 	.config_intr	= bcm_phy_config_intr,
 }, {
+	.phy_id         = PHY_ID_BCM54810,
+	.phy_id_mask    = 0xfffffff0,
+	.name           = "Broadcom BCM54810",
+	.features       = PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
+	.config_init    = bcm54xx_config_init,
+	.config_aneg    = bcm5481_config_aneg,
+	.read_status    = genphy_read_status,
+	.ack_interrupt  = bcm_phy_ack_intr,
+	.config_intr    = bcm_phy_config_intr,
+}, {
 	.phy_id		= PHY_ID_BCM5482,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5482",
@@ -661,6 +716,7 @@ static struct mdio_device_id __maybe_unused broadcom_tbl[] = {
 	{ PHY_ID_BCM54616S, 0xfffffff0 },
 	{ PHY_ID_BCM5464, 0xfffffff0 },
 	{ PHY_ID_BCM5481, 0xfffffff0 },
+	{ PHY_ID_BCM54810, 0xfffffff0 },
 	{ PHY_ID_BCM5482, 0xfffffff0 },
 	{ PHY_ID_BCM50610, 0xfffffff0 },
 	{ PHY_ID_BCM50610M, 0xfffffff0 },
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 0ed6691..848dc50 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -13,6 +13,7 @@
 #define PHY_ID_BCM5241			0x0143bc30
 #define PHY_ID_BCMAC131			0x0143bc70
 #define PHY_ID_BCM5481			0x0143bca0
+#define PHY_ID_BCM54810			0x03625d00
 #define PHY_ID_BCM5482			0x0143bcb0
 #define PHY_ID_BCM5411			0x00206070
 #define PHY_ID_BCM5421			0x002060e0
@@ -56,6 +57,7 @@
 #define PHY_BRCM_EXT_IBND_TX_ENABLE	0x00002000
 #define PHY_BRCM_CLEAR_RGMII_MODE	0x00004000
 #define PHY_BRCM_DIS_TXCRXC_NOENRGY	0x00008000
+
 /* Broadcom BCM7xxx specific workarounds */
 #define PHY_BRCM_7XXX_REV(x)		(((x) >> 8) & 0xff)
 #define PHY_BRCM_7XXX_PATCH(x)		((x) & 0xff)
@@ -111,6 +113,7 @@
 #define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
 #define MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT	12
+#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN	(1 << 8)
 
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MASK	0x0007
 
@@ -192,6 +195,12 @@
 #define BCM5482_SSD_SGMII_SLAVE_EN	0x0002	/* Slave mode enable */
 #define BCM5482_SSD_SGMII_SLAVE_AD	0x0001	/* Slave auto-detection */
 
+/* BCM54810 Registers */
+#define BCM54810_EXP_BROADREACH_LRE_MISC_CTL	(MII_BCM54XX_EXP_SEL_ER + 0x90)
+#define BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN	(1 << 0)
+#define BCM54810_SHD_CLK_CTL			0x3
+#define BCM54810_SHD_CLK_CTL_GTXCLK_EN		(1 << 9)
+
 
 /*****************************************************************************/
 /* Fast Ethernet Transceiver definitions. */
-- 
2.7.4

[PATCH v4 3/7] net: phy: broadcom: Add BCM54810 PHY entry

[Jon Mason]

The BCM54810 PHY requires some semi-unique configuration, which results
in some additional configuration in addition to the standard config.
Also, some users of the BCM54810 require the PHY lanes to be swapped.
Since there is no way to detect this, add a device tree query to see if
it is applicable.

Inspired-by: Vikas Soni <vsoni@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 drivers/net/phy/Kconfig    |  2 +-
 drivers/net/phy/broadcom.c | 58 +++++++++++++++++++++++++++++++++++++++++++++-
 include/linux/brcmphy.h    |  9 +++++++
 3 files changed, 67 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 45f68ea..31967ca 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -217,7 +217,7 @@ config BROADCOM_PHY
 	select BCM_NET_PHYLIB
 	---help---
 	  Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
-	  BCM5481 and BCM5482 PHYs.
+	  BCM5481, BCM54810 and BCM5482 PHYs.
 
 config CICADA_PHY
 	tristate "Cicada PHYs"
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 3a64b3d..b1e32e9 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -18,7 +18,7 @@
 #include <linux/module.h>
 #include <linux/phy.h>
 #include <linux/brcmphy.h>
-
+#include <linux/of.h>
 
 #define BRCM_PHY_MODEL(phydev) \
 	((phydev)->drv->phy_id & (phydev)->drv->phy_id_mask)
@@ -45,6 +45,34 @@ static int bcm54xx_auxctl_write(struct phy_device *phydev, u16 regnum, u16 val)
 	return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
 }
 
+static int bcm54810_config(struct phy_device *phydev)
+{
+	int rc, val;
+
+	val = bcm_phy_read_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL);
+	val &= ~BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN;
+	rc = bcm_phy_write_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL,
+			       val);
+	if (rc < 0)
+		return rc;
+
+	val = bcm54xx_auxctl_read(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
+	val &= ~MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN;
+	val |= MII_BCM54XX_AUXCTL_MISC_WREN;
+	rc = bcm54xx_auxctl_write(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC,
+				  val);
+	if (rc < 0)
+		return rc;
+
+	val = bcm_phy_read_shadow(phydev, BCM54810_SHD_CLK_CTL);
+	val &= ~BCM54810_SHD_CLK_CTL_GTXCLK_EN;
+	rc = bcm_phy_write_shadow(phydev, BCM54810_SHD_CLK_CTL, val);
+	if (rc < 0)
+		return rc;
+
+	return 0;
+}
+
 /* Needs SMDSP clock enabled via bcm54xx_phydsp_config() */
 static int bcm50610_a0_workaround(struct phy_device *phydev)
 {
@@ -217,6 +245,12 @@ static int bcm54xx_config_init(struct phy_device *phydev)
 	    (phydev->dev_flags & PHY_BRCM_AUTO_PWRDWN_ENABLE))
 		bcm54xx_adjust_rxrefclk(phydev);
 
+	if (BRCM_PHY_MODEL(phydev) == PHY_ID_BCM54810) {
+		err = bcm54810_config(phydev);
+		if (err)
+			return err;
+	}
+
 	bcm54xx_phydsp_config(phydev);
 
 	return 0;
@@ -314,6 +348,7 @@ static int bcm5482_read_status(struct phy_device *phydev)
 
 static int bcm5481_config_aneg(struct phy_device *phydev)
 {
+	struct device_node *np = phydev->mdio.dev.of_node;
 	int ret;
 
 	/* Aneg firsly. */
@@ -344,6 +379,14 @@ static int bcm5481_config_aneg(struct phy_device *phydev)
 		phy_write(phydev, 0x18, reg);
 	}
 
+	if (of_property_read_bool(np, "enet-phy-lane-swap")) {
+		/* Lane Swap - Undocumented register...magic! */
+		ret = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_SEL_ER + 0x9,
+					0x11B);
+		if (ret < 0)
+			return ret;
+	}
+
 	return ret;
 }
 
@@ -578,6 +621,18 @@ static struct phy_driver broadcom_drivers[] = {
 	.ack_interrupt	= bcm_phy_ack_intr,
 	.config_intr	= bcm_phy_config_intr,
 }, {
+	.phy_id         = PHY_ID_BCM54810,
+	.phy_id_mask    = 0xfffffff0,
+	.name           = "Broadcom BCM54810",
+	.features       = PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
+	.config_init    = bcm54xx_config_init,
+	.config_aneg    = bcm5481_config_aneg,
+	.read_status    = genphy_read_status,
+	.ack_interrupt  = bcm_phy_ack_intr,
+	.config_intr    = bcm_phy_config_intr,
+}, {
 	.phy_id		= PHY_ID_BCM5482,
 	.phy_id_mask	= 0xfffffff0,
 	.name		= "Broadcom BCM5482",
@@ -661,6 +716,7 @@ static struct mdio_device_id __maybe_unused broadcom_tbl[] = {
 	{ PHY_ID_BCM54616S, 0xfffffff0 },
 	{ PHY_ID_BCM5464, 0xfffffff0 },
 	{ PHY_ID_BCM5481, 0xfffffff0 },
+	{ PHY_ID_BCM54810, 0xfffffff0 },
 	{ PHY_ID_BCM5482, 0xfffffff0 },
 	{ PHY_ID_BCM50610, 0xfffffff0 },
 	{ PHY_ID_BCM50610M, 0xfffffff0 },
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 0ed6691..848dc50 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -13,6 +13,7 @@
 #define PHY_ID_BCM5241			0x0143bc30
 #define PHY_ID_BCMAC131			0x0143bc70
 #define PHY_ID_BCM5481			0x0143bca0
+#define PHY_ID_BCM54810			0x03625d00
 #define PHY_ID_BCM5482			0x0143bcb0
 #define PHY_ID_BCM5411			0x00206070
 #define PHY_ID_BCM5421			0x002060e0
@@ -56,6 +57,7 @@
 #define PHY_BRCM_EXT_IBND_TX_ENABLE	0x00002000
 #define PHY_BRCM_CLEAR_RGMII_MODE	0x00004000
 #define PHY_BRCM_DIS_TXCRXC_NOENRGY	0x00008000
+
 /* Broadcom BCM7xxx specific workarounds */
 #define PHY_BRCM_7XXX_REV(x)		(((x) >> 8) & 0xff)
 #define PHY_BRCM_7XXX_PATCH(x)		((x) & 0xff)
@@ -111,6 +113,7 @@
 #define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC	0x7000
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MISC	0x0007
 #define MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT	12
+#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN	(1 << 8)
 
 #define MII_BCM54XX_AUXCTL_SHDWSEL_MASK	0x0007
 
@@ -192,6 +195,12 @@
 #define BCM5482_SSD_SGMII_SLAVE_EN	0x0002	/* Slave mode enable */
 #define BCM5482_SSD_SGMII_SLAVE_AD	0x0001	/* Slave auto-detection */
 
+/* BCM54810 Registers */
+#define BCM54810_EXP_BROADREACH_LRE_MISC_CTL	(MII_BCM54XX_EXP_SEL_ER + 0x90)
+#define BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN	(1 << 0)
+#define BCM54810_SHD_CLK_CTL			0x3
+#define BCM54810_SHD_CLK_CTL_GTXCLK_EN		(1 << 9)
+
 
 /*****************************************************************************/
 /* Fast Ethernet Transceiver definitions. */
-- 
2.7.4

[PATCH v4 4/7] Documentation: devicetree: net: add NS2 bindings to amac

[Jon Mason]

Clean-up the documentation to the bgmac-amac driver, per suggestion by
Rob Herring, and add details for NS2 support.

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 Documentation/devicetree/bindings/net/brcm,amac.txt | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt
index ba5ecc1..2fefa1a 100644
--- a/Documentation/devicetree/bindings/net/brcm,amac.txt
+++ b/Documentation/devicetree/bindings/net/brcm,amac.txt
@@ -2,11 +2,17 @@ Broadcom AMAC Ethernet Controller Device Tree Bindings
 -------------------------------------------------------------
 
 Required properties:
- - compatible:	"brcm,amac" or "brcm,nsp-amac"
- - reg:		Address and length of the GMAC registers,
-		Address and length of the GMAC IDM registers
- - reg-names:	Names of the registers.  Must have both "amac_base" and
-		"idm_base"
+ - compatible:	"brcm,amac"
+		"brcm,nsp-amac"
+		"brcm,ns2-amac"
+ - reg:		Address and length of the register set for the device. It
+		contains the information of registers in the same order as
+		described by reg-names
+ - reg-names:	Names of the registers.
+		"amac_base":	Address and length of the GMAC registers
+		"idm_base":	Address and length of the GMAC IDM registers
+		"nicpm_base":	Address and length of the NIC Port Manager
+				registers (required for Northstar2)
  - interrupts:	Interrupt number
 
 Optional properties:
-- 
2.7.4

[PATCH v4 4/7] Documentation: devicetree: net: add NS2 bindings to amac

[Jon Mason]

Clean-up the documentation to the bgmac-amac driver, per suggestion by
Rob Herring, and add details for NS2 support.

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 Documentation/devicetree/bindings/net/brcm,amac.txt | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt
index ba5ecc1..2fefa1a 100644
--- a/Documentation/devicetree/bindings/net/brcm,amac.txt
+++ b/Documentation/devicetree/bindings/net/brcm,amac.txt
@@ -2,11 +2,17 @@ Broadcom AMAC Ethernet Controller Device Tree Bindings
 -------------------------------------------------------------
 
 Required properties:
- - compatible:	"brcm,amac" or "brcm,nsp-amac"
- - reg:		Address and length of the GMAC registers,
-		Address and length of the GMAC IDM registers
- - reg-names:	Names of the registers.  Must have both "amac_base" and
-		"idm_base"
+ - compatible:	"brcm,amac"
+		"brcm,nsp-amac"
+		"brcm,ns2-amac"
+ - reg:		Address and length of the register set for the device. It
+		contains the information of registers in the same order as
+		described by reg-names
+ - reg-names:	Names of the registers.
+		"amac_base":	Address and length of the GMAC registers
+		"idm_base":	Address and length of the GMAC IDM registers
+		"nicpm_base":	Address and length of the NIC Port Manager
+				registers (required for Northstar2)
  - interrupts:	Interrupt number
 
 Optional properties:
-- 
2.7.4

[PATCH v4 5/7] net: ethernet: bgmac: device tree phy enablement

[Jon Mason]

Change the bgmac driver to allow for phy's defined by the device tree

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 drivers/net/ethernet/broadcom/bgmac-bcma.c     | 48 ++++++++++++++++++++++++
 drivers/net/ethernet/broadcom/bgmac-platform.c | 48 +++++++++++++++++++++++-
 drivers/net/ethernet/broadcom/bgmac.c          | 52 ++------------------------
 drivers/net/ethernet/broadcom/bgmac.h          |  7 ++++
 4 files changed, 105 insertions(+), 50 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/bgmac-bcma.c b/drivers/net/ethernet/broadcom/bgmac-bcma.c
index c16ec3a..3e3efde 100644
--- a/drivers/net/ethernet/broadcom/bgmac-bcma.c
+++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c
@@ -80,6 +80,50 @@ static void bcma_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset, u32 mask,
 	bcma_maskset32(bgmac->bcma.cmn, offset, mask, set);
 }
 
+static int bcma_phy_connect(struct bgmac *bgmac)
+{
+	struct phy_device *phy_dev;
+	char bus_id[MII_BUS_ID_SIZE + 3];
+
+	/* Connect to the PHY */
+	snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id,
+		 bgmac->phyaddr);
+	phy_dev = phy_connect(bgmac->net_dev, bus_id, bgmac_adjust_link,
+			      PHY_INTERFACE_MODE_MII);
+	if (IS_ERR(phy_dev)) {
+		dev_err(bgmac->dev, "PHY connecton failed\n");
+		return PTR_ERR(phy_dev);
+	}
+
+	return 0;
+}
+
+static int bcma_phy_direct_connect(struct bgmac *bgmac)
+{
+	struct fixed_phy_status fphy_status = {
+		.link = 1,
+		.speed = SPEED_1000,
+		.duplex = DUPLEX_FULL,
+	};
+	struct phy_device *phy_dev;
+	int err;
+
+	phy_dev = fixed_phy_register(PHY_POLL, &fphy_status, -1, NULL);
+	if (!phy_dev || IS_ERR(phy_dev)) {
+		dev_err(bgmac->dev, "Failed to register fixed PHY device\n");
+		return -ENODEV;
+	}
+
+	err = phy_connect_direct(bgmac->net_dev, phy_dev, bgmac_adjust_link,
+				 PHY_INTERFACE_MODE_MII);
+	if (err) {
+		dev_err(bgmac->dev, "Connecting PHY failed\n");
+		return err;
+	}
+
+	return err;
+}
+
 static const struct bcma_device_id bgmac_bcma_tbl[] = {
 	BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_4706_MAC_GBIT,
 		  BCMA_ANY_REV, BCMA_ANY_CLASS),
@@ -275,6 +319,10 @@ static int bgmac_probe(struct bcma_device *core)
 	bgmac->cco_ctl_maskset = bcma_bgmac_cco_ctl_maskset;
 	bgmac->get_bus_clock = bcma_bgmac_get_bus_clock;
 	bgmac->cmn_maskset32 = bcma_bgmac_cmn_maskset32;
+	if (bgmac->mii_bus)
+		bgmac->phy_connect = bcma_phy_connect;
+	else
+		bgmac->phy_connect = bcma_phy_direct_connect;
 
 	err = bgmac_enet_probe(bgmac);
 	if (err)
diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
index be52f27..aed5dc5 100644
--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
@@ -16,6 +16,7 @@
 #include <linux/bcma/bcma.h>
 #include <linux/etherdevice.h>
 #include <linux/of_address.h>
+#include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include "bgmac.h"
 
@@ -86,6 +87,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
 	WARN_ON(1);
 }
 
+static int platform_phy_connect(struct bgmac *bgmac)
+{
+	struct phy_device *phy_dev;
+
+	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
+					 bgmac_adjust_link);
+	if (!phy_dev) {
+		dev_err(bgmac->dev, "Phy connect failed\n");
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static int platform_phy_direct_connect(struct bgmac *bgmac)
+{
+	struct fixed_phy_status fphy_status = {
+		.link = 1,
+		.speed = SPEED_1000,
+		.duplex = DUPLEX_FULL,
+	};
+	struct phy_device *phy_dev;
+	int err;
+
+	phy_dev = fixed_phy_register(PHY_POLL, &fphy_status, -1, NULL);
+	if (!phy_dev || IS_ERR(phy_dev)) {
+		dev_err(bgmac->dev, "Failed to register fixed PHY device\n");
+		return -ENODEV;
+	}
+
+	err = phy_connect_direct(bgmac->net_dev, phy_dev, bgmac_adjust_link,
+				 PHY_INTERFACE_MODE_MII);
+	if (err) {
+		dev_err(bgmac->dev, "Connecting PHY failed\n");
+		return err;
+	}
+
+	return err;
+}
+
 static int bgmac_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
@@ -102,7 +143,6 @@ static int bgmac_probe(struct platform_device *pdev)
 	/* Set the features of the 4707 family */
 	bgmac->feature_flags |= BGMAC_FEAT_CLKCTLST;
 	bgmac->feature_flags |= BGMAC_FEAT_NO_RESET;
-	bgmac->feature_flags |= BGMAC_FEAT_FORCE_SPEED_2500;
 	bgmac->feature_flags |= BGMAC_FEAT_CMDCFG_SR_REV4;
 	bgmac->feature_flags |= BGMAC_FEAT_TX_MASK_SETUP;
 	bgmac->feature_flags |= BGMAC_FEAT_RX_MASK_SETUP;
@@ -151,6 +191,12 @@ static int bgmac_probe(struct platform_device *pdev)
 	bgmac->cco_ctl_maskset = platform_bgmac_cco_ctl_maskset;
 	bgmac->get_bus_clock = platform_bgmac_get_bus_clock;
 	bgmac->cmn_maskset32 = platform_bgmac_cmn_maskset32;
+	if (of_parse_phandle(np, "phy-handle", 0)) {
+		bgmac->phy_connect = platform_phy_connect;
+	} else {
+		bgmac->phy_connect = platform_phy_direct_connect;
+		bgmac->feature_flags |= BGMAC_FEAT_FORCE_SPEED_2500;
+	}
 
 	return bgmac_enet_probe(bgmac);
 }
diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
index 856379c..4584958 100644
--- a/drivers/net/ethernet/broadcom/bgmac.c
+++ b/drivers/net/ethernet/broadcom/bgmac.c
@@ -1388,7 +1388,7 @@ static const struct ethtool_ops bgmac_ethtool_ops = {
  * MII
  **************************************************/
 
-static void bgmac_adjust_link(struct net_device *net_dev)
+void bgmac_adjust_link(struct net_device *net_dev)
 {
 	struct bgmac *bgmac = netdev_priv(net_dev);
 	struct phy_device *phy_dev = net_dev->phydev;
@@ -1411,50 +1411,7 @@ static void bgmac_adjust_link(struct net_device *net_dev)
 		phy_print_status(phy_dev);
 	}
 }
-
-static int bgmac_phy_connect_direct(struct bgmac *bgmac)
-{
-	struct fixed_phy_status fphy_status = {
-		.link = 1,
-		.speed = SPEED_1000,
-		.duplex = DUPLEX_FULL,
-	};
-	struct phy_device *phy_dev;
-	int err;
-
-	phy_dev = fixed_phy_register(PHY_POLL, &fphy_status, -1, NULL);
-	if (!phy_dev || IS_ERR(phy_dev)) {
-		dev_err(bgmac->dev, "Failed to register fixed PHY device\n");
-		return -ENODEV;
-	}
-
-	err = phy_connect_direct(bgmac->net_dev, phy_dev, bgmac_adjust_link,
-				 PHY_INTERFACE_MODE_MII);
-	if (err) {
-		dev_err(bgmac->dev, "Connecting PHY failed\n");
-		return err;
-	}
-
-	return err;
-}
-
-static int bgmac_phy_connect(struct bgmac *bgmac)
-{
-	struct phy_device *phy_dev;
-	char bus_id[MII_BUS_ID_SIZE + 3];
-
-	/* Connect to the PHY */
-	snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id,
-		 bgmac->phyaddr);
-	phy_dev = phy_connect(bgmac->net_dev, bus_id, &bgmac_adjust_link,
-			      PHY_INTERFACE_MODE_MII);
-	if (IS_ERR(phy_dev)) {
-		dev_err(bgmac->dev, "PHY connecton failed\n");
-		return PTR_ERR(phy_dev);
-	}
-
-	return 0;
-}
+EXPORT_SYMBOL_GPL(bgmac_adjust_link);
 
 int bgmac_enet_probe(struct bgmac *info)
 {
@@ -1507,10 +1464,7 @@ int bgmac_enet_probe(struct bgmac *info)
 
 	netif_napi_add(net_dev, &bgmac->napi, bgmac_poll, BGMAC_WEIGHT);
 
-	if (!bgmac->mii_bus)
-		err = bgmac_phy_connect_direct(bgmac);
-	else
-		err = bgmac_phy_connect(bgmac);
+	err = bgmac_phy_connect(bgmac);
 	if (err) {
 		dev_err(bgmac->dev, "Cannot connect to phy\n");
 		goto err_dma_free;
diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
index 80836b4..ea52ac3 100644
--- a/drivers/net/ethernet/broadcom/bgmac.h
+++ b/drivers/net/ethernet/broadcom/bgmac.h
@@ -513,10 +513,12 @@ struct bgmac {
 	u32 (*get_bus_clock)(struct bgmac *bgmac);
 	void (*cmn_maskset32)(struct bgmac *bgmac, u16 offset, u32 mask,
 			      u32 set);
+	int (*phy_connect)(struct bgmac *bgmac);
 };
 
 int bgmac_enet_probe(struct bgmac *info);
 void bgmac_enet_remove(struct bgmac *bgmac);
+void bgmac_adjust_link(struct net_device *net_dev);
 
 struct mii_bus *bcma_mdio_mii_register(struct bcma_device *core, u8 phyaddr);
 void bcma_mdio_mii_unregister(struct mii_bus *mii_bus);
@@ -583,4 +585,9 @@ static inline void bgmac_set(struct bgmac *bgmac, u16 offset, u32 set)
 {
 	bgmac_maskset(bgmac, offset, ~0, set);
 }
+
+static inline int bgmac_phy_connect(struct bgmac *bgmac)
+{
+	return bgmac->phy_connect(bgmac);
+}
 #endif /* _BGMAC_H */
-- 
2.7.4

[PATCH v4 5/7] net: ethernet: bgmac: device tree phy enablement

[Jon Mason]

Change the bgmac driver to allow for phy's defined by the device tree

Signed-off-by: Jon Mason <jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
---
 drivers/net/ethernet/broadcom/bgmac-bcma.c     | 48 ++++++++++++++++++++++++
 drivers/net/ethernet/broadcom/bgmac-platform.c | 48 +++++++++++++++++++++++-
 drivers/net/ethernet/broadcom/bgmac.c          | 52 ++------------------------
 drivers/net/ethernet/broadcom/bgmac.h          |  7 ++++
 4 files changed, 105 insertions(+), 50 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/bgmac-bcma.c b/drivers/net/ethernet/broadcom/bgmac-bcma.c
index c16ec3a..3e3efde 100644
--- a/drivers/net/ethernet/broadcom/bgmac-bcma.c
+++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c
@@ -80,6 +80,50 @@ static void bcma_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset, u32 mask,
 	bcma_maskset32(bgmac->bcma.cmn, offset, mask, set);
 }
 
+static int bcma_phy_connect(struct bgmac *bgmac)
+{
+	struct phy_device *phy_dev;
+	char bus_id[MII_BUS_ID_SIZE + 3];
+
+	/* Connect to the PHY */
+	snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id,
+		 bgmac->phyaddr);
+	phy_dev = phy_connect(bgmac->net_dev, bus_id, bgmac_adjust_link,
+			      PHY_INTERFACE_MODE_MII);
+	if (IS_ERR(phy_dev)) {
+		dev_err(bgmac->dev, "PHY connecton failed\n");
+		return PTR_ERR(phy_dev);
+	}
+
+	return 0;
+}
+
+static int bcma_phy_direct_connect(struct bgmac *bgmac)
+{
+	struct fixed_phy_status fphy_status = {
+		.link = 1,
+		.speed = SPEED_1000,
+		.duplex = DUPLEX_FULL,
+	};
+	struct phy_device *phy_dev;
+	int err;
+
+	phy_dev = fixed_phy_register(PHY_POLL, &fphy_status, -1, NULL);
+	if (!phy_dev || IS_ERR(phy_dev)) {
+		dev_err(bgmac->dev, "Failed to register fixed PHY device\n");
+		return -ENODEV;
+	}
+
+	err = phy_connect_direct(bgmac->net_dev, phy_dev, bgmac_adjust_link,
+				 PHY_INTERFACE_MODE_MII);
+	if (err) {
+		dev_err(bgmac->dev, "Connecting PHY failed\n");
+		return err;
+	}
+
+	return err;
+}
+
 static const struct bcma_device_id bgmac_bcma_tbl[] = {
 	BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_4706_MAC_GBIT,
 		  BCMA_ANY_REV, BCMA_ANY_CLASS),
@@ -275,6 +319,10 @@ static int bgmac_probe(struct bcma_device *core)
 	bgmac->cco_ctl_maskset = bcma_bgmac_cco_ctl_maskset;
 	bgmac->get_bus_clock = bcma_bgmac_get_bus_clock;
 	bgmac->cmn_maskset32 = bcma_bgmac_cmn_maskset32;
+	if (bgmac->mii_bus)
+		bgmac->phy_connect = bcma_phy_connect;
+	else
+		bgmac->phy_connect = bcma_phy_direct_connect;
 
 	err = bgmac_enet_probe(bgmac);
 	if (err)
diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
index be52f27..aed5dc5 100644
--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
@@ -16,6 +16,7 @@
 #include <linux/bcma/bcma.h>
 #include <linux/etherdevice.h>
 #include <linux/of_address.h>
+#include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include "bgmac.h"
 
@@ -86,6 +87,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
 	WARN_ON(1);
 }
 
+static int platform_phy_connect(struct bgmac *bgmac)
+{
+	struct phy_device *phy_dev;
+
+	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
+					 bgmac_adjust_link);
+	if (!phy_dev) {
+		dev_err(bgmac->dev, "Phy connect failed\n");
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static int platform_phy_direct_connect(struct bgmac *bgmac)
+{
+	struct fixed_phy_status fphy_status = {
+		.link = 1,
+		.speed = SPEED_1000,
+		.duplex = DUPLEX_FULL,
+	};
+	struct phy_device *phy_dev;
+	int err;
+
+	phy_dev = fixed_phy_register(PHY_POLL, &fphy_status, -1, NULL);
+	if (!phy_dev || IS_ERR(phy_dev)) {
+		dev_err(bgmac->dev, "Failed to register fixed PHY device\n");
+		return -ENODEV;
+	}
+
+	err = phy_connect_direct(bgmac->net_dev, phy_dev, bgmac_adjust_link,
+				 PHY_INTERFACE_MODE_MII);
+	if (err) {
+		dev_err(bgmac->dev, "Connecting PHY failed\n");
+		return err;
+	}
+
+	return err;
+}
+
 static int bgmac_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
@@ -102,7 +143,6 @@ static int bgmac_probe(struct platform_device *pdev)
 	/* Set the features of the 4707 family */
 	bgmac->feature_flags |= BGMAC_FEAT_CLKCTLST;
 	bgmac->feature_flags |= BGMAC_FEAT_NO_RESET;
-	bgmac->feature_flags |= BGMAC_FEAT_FORCE_SPEED_2500;
 	bgmac->feature_flags |= BGMAC_FEAT_CMDCFG_SR_REV4;
 	bgmac->feature_flags |= BGMAC_FEAT_TX_MASK_SETUP;
 	bgmac->feature_flags |= BGMAC_FEAT_RX_MASK_SETUP;
@@ -151,6 +191,12 @@ static int bgmac_probe(struct platform_device *pdev)
 	bgmac->cco_ctl_maskset = platform_bgmac_cco_ctl_maskset;
 	bgmac->get_bus_clock = platform_bgmac_get_bus_clock;
 	bgmac->cmn_maskset32 = platform_bgmac_cmn_maskset32;
+	if (of_parse_phandle(np, "phy-handle", 0)) {
+		bgmac->phy_connect = platform_phy_connect;
+	} else {
+		bgmac->phy_connect = platform_phy_direct_connect;
+		bgmac->feature_flags |= BGMAC_FEAT_FORCE_SPEED_2500;
+	}
 
 	return bgmac_enet_probe(bgmac);
 }
diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
index 856379c..4584958 100644
--- a/drivers/net/ethernet/broadcom/bgmac.c
+++ b/drivers/net/ethernet/broadcom/bgmac.c
@@ -1388,7 +1388,7 @@ static const struct ethtool_ops bgmac_ethtool_ops = {
  * MII
  **************************************************/
 
-static void bgmac_adjust_link(struct net_device *net_dev)
+void bgmac_adjust_link(struct net_device *net_dev)
 {
 	struct bgmac *bgmac = netdev_priv(net_dev);
 	struct phy_device *phy_dev = net_dev->phydev;
@@ -1411,50 +1411,7 @@ static void bgmac_adjust_link(struct net_device *net_dev)
 		phy_print_status(phy_dev);
 	}
 }
-
-static int bgmac_phy_connect_direct(struct bgmac *bgmac)
-{
-	struct fixed_phy_status fphy_status = {
-		.link = 1,
-		.speed = SPEED_1000,
-		.duplex = DUPLEX_FULL,
-	};
-	struct phy_device *phy_dev;
-	int err;
-
-	phy_dev = fixed_phy_register(PHY_POLL, &fphy_status, -1, NULL);
-	if (!phy_dev || IS_ERR(phy_dev)) {
-		dev_err(bgmac->dev, "Failed to register fixed PHY device\n");
-		return -ENODEV;
-	}
-
-	err = phy_connect_direct(bgmac->net_dev, phy_dev, bgmac_adjust_link,
-				 PHY_INTERFACE_MODE_MII);
-	if (err) {
-		dev_err(bgmac->dev, "Connecting PHY failed\n");
-		return err;
-	}
-
-	return err;
-}
-
-static int bgmac_phy_connect(struct bgmac *bgmac)
-{
-	struct phy_device *phy_dev;
-	char bus_id[MII_BUS_ID_SIZE + 3];
-
-	/* Connect to the PHY */
-	snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id,
-		 bgmac->phyaddr);
-	phy_dev = phy_connect(bgmac->net_dev, bus_id, &bgmac_adjust_link,
-			      PHY_INTERFACE_MODE_MII);
-	if (IS_ERR(phy_dev)) {
-		dev_err(bgmac->dev, "PHY connecton failed\n");
-		return PTR_ERR(phy_dev);
-	}
-
-	return 0;
-}
+EXPORT_SYMBOL_GPL(bgmac_adjust_link);
 
 int bgmac_enet_probe(struct bgmac *info)
 {
@@ -1507,10 +1464,7 @@ int bgmac_enet_probe(struct bgmac *info)
 
 	netif_napi_add(net_dev, &bgmac->napi, bgmac_poll, BGMAC_WEIGHT);
 
-	if (!bgmac->mii_bus)
-		err = bgmac_phy_connect_direct(bgmac);
-	else
-		err = bgmac_phy_connect(bgmac);
+	err = bgmac_phy_connect(bgmac);
 	if (err) {
 		dev_err(bgmac->dev, "Cannot connect to phy\n");
 		goto err_dma_free;
diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
index 80836b4..ea52ac3 100644
--- a/drivers/net/ethernet/broadcom/bgmac.h
+++ b/drivers/net/ethernet/broadcom/bgmac.h
@@ -513,10 +513,12 @@ struct bgmac {
 	u32 (*get_bus_clock)(struct bgmac *bgmac);
 	void (*cmn_maskset32)(struct bgmac *bgmac, u16 offset, u32 mask,
 			      u32 set);
+	int (*phy_connect)(struct bgmac *bgmac);
 };
 
 int bgmac_enet_probe(struct bgmac *info);
 void bgmac_enet_remove(struct bgmac *bgmac);
+void bgmac_adjust_link(struct net_device *net_dev);
 
 struct mii_bus *bcma_mdio_mii_register(struct bcma_device *core, u8 phyaddr);
 void bcma_mdio_mii_unregister(struct mii_bus *mii_bus);
@@ -583,4 +585,9 @@ static inline void bgmac_set(struct bgmac *bgmac, u16 offset, u32 set)
 {
 	bgmac_maskset(bgmac, offset, ~0, set);
 }
+
+static inline int bgmac_phy_connect(struct bgmac *bgmac)
+{
+	return bgmac->phy_connect(bgmac);
+}
 #endif /* _BGMAC_H */
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 5/7] net: ethernet: bgmac: device tree phy enablement

[Jon Mason]

Change the bgmac driver to allow for phy's defined by the device tree

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 drivers/net/ethernet/broadcom/bgmac-bcma.c     | 48 ++++++++++++++++++++++++
 drivers/net/ethernet/broadcom/bgmac-platform.c | 48 +++++++++++++++++++++++-
 drivers/net/ethernet/broadcom/bgmac.c          | 52 ++------------------------
 drivers/net/ethernet/broadcom/bgmac.h          |  7 ++++
 4 files changed, 105 insertions(+), 50 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/bgmac-bcma.c b/drivers/net/ethernet/broadcom/bgmac-bcma.c
index c16ec3a..3e3efde 100644
--- a/drivers/net/ethernet/broadcom/bgmac-bcma.c
+++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c
@@ -80,6 +80,50 @@ static void bcma_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset, u32 mask,
 	bcma_maskset32(bgmac->bcma.cmn, offset, mask, set);
 }
 
+static int bcma_phy_connect(struct bgmac *bgmac)
+{
+	struct phy_device *phy_dev;
+	char bus_id[MII_BUS_ID_SIZE + 3];
+
+	/* Connect to the PHY */
+	snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id,
+		 bgmac->phyaddr);
+	phy_dev = phy_connect(bgmac->net_dev, bus_id, bgmac_adjust_link,
+			      PHY_INTERFACE_MODE_MII);
+	if (IS_ERR(phy_dev)) {
+		dev_err(bgmac->dev, "PHY connecton failed\n");
+		return PTR_ERR(phy_dev);
+	}
+
+	return 0;
+}
+
+static int bcma_phy_direct_connect(struct bgmac *bgmac)
+{
+	struct fixed_phy_status fphy_status = {
+		.link = 1,
+		.speed = SPEED_1000,
+		.duplex = DUPLEX_FULL,
+	};
+	struct phy_device *phy_dev;
+	int err;
+
+	phy_dev = fixed_phy_register(PHY_POLL, &fphy_status, -1, NULL);
+	if (!phy_dev || IS_ERR(phy_dev)) {
+		dev_err(bgmac->dev, "Failed to register fixed PHY device\n");
+		return -ENODEV;
+	}
+
+	err = phy_connect_direct(bgmac->net_dev, phy_dev, bgmac_adjust_link,
+				 PHY_INTERFACE_MODE_MII);
+	if (err) {
+		dev_err(bgmac->dev, "Connecting PHY failed\n");
+		return err;
+	}
+
+	return err;
+}
+
 static const struct bcma_device_id bgmac_bcma_tbl[] = {
 	BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_4706_MAC_GBIT,
 		  BCMA_ANY_REV, BCMA_ANY_CLASS),
@@ -275,6 +319,10 @@ static int bgmac_probe(struct bcma_device *core)
 	bgmac->cco_ctl_maskset = bcma_bgmac_cco_ctl_maskset;
 	bgmac->get_bus_clock = bcma_bgmac_get_bus_clock;
 	bgmac->cmn_maskset32 = bcma_bgmac_cmn_maskset32;
+	if (bgmac->mii_bus)
+		bgmac->phy_connect = bcma_phy_connect;
+	else
+		bgmac->phy_connect = bcma_phy_direct_connect;
 
 	err = bgmac_enet_probe(bgmac);
 	if (err)
diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
index be52f27..aed5dc5 100644
--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
@@ -16,6 +16,7 @@
 #include <linux/bcma/bcma.h>
 #include <linux/etherdevice.h>
 #include <linux/of_address.h>
+#include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include "bgmac.h"
 
@@ -86,6 +87,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
 	WARN_ON(1);
 }
 
+static int platform_phy_connect(struct bgmac *bgmac)
+{
+	struct phy_device *phy_dev;
+
+	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
+					 bgmac_adjust_link);
+	if (!phy_dev) {
+		dev_err(bgmac->dev, "Phy connect failed\n");
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static int platform_phy_direct_connect(struct bgmac *bgmac)
+{
+	struct fixed_phy_status fphy_status = {
+		.link = 1,
+		.speed = SPEED_1000,
+		.duplex = DUPLEX_FULL,
+	};
+	struct phy_device *phy_dev;
+	int err;
+
+	phy_dev = fixed_phy_register(PHY_POLL, &fphy_status, -1, NULL);
+	if (!phy_dev || IS_ERR(phy_dev)) {
+		dev_err(bgmac->dev, "Failed to register fixed PHY device\n");
+		return -ENODEV;
+	}
+
+	err = phy_connect_direct(bgmac->net_dev, phy_dev, bgmac_adjust_link,
+				 PHY_INTERFACE_MODE_MII);
+	if (err) {
+		dev_err(bgmac->dev, "Connecting PHY failed\n");
+		return err;
+	}
+
+	return err;
+}
+
 static int bgmac_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
@@ -102,7 +143,6 @@ static int bgmac_probe(struct platform_device *pdev)
 	/* Set the features of the 4707 family */
 	bgmac->feature_flags |= BGMAC_FEAT_CLKCTLST;
 	bgmac->feature_flags |= BGMAC_FEAT_NO_RESET;
-	bgmac->feature_flags |= BGMAC_FEAT_FORCE_SPEED_2500;
 	bgmac->feature_flags |= BGMAC_FEAT_CMDCFG_SR_REV4;
 	bgmac->feature_flags |= BGMAC_FEAT_TX_MASK_SETUP;
 	bgmac->feature_flags |= BGMAC_FEAT_RX_MASK_SETUP;
@@ -151,6 +191,12 @@ static int bgmac_probe(struct platform_device *pdev)
 	bgmac->cco_ctl_maskset = platform_bgmac_cco_ctl_maskset;
 	bgmac->get_bus_clock = platform_bgmac_get_bus_clock;
 	bgmac->cmn_maskset32 = platform_bgmac_cmn_maskset32;
+	if (of_parse_phandle(np, "phy-handle", 0)) {
+		bgmac->phy_connect = platform_phy_connect;
+	} else {
+		bgmac->phy_connect = platform_phy_direct_connect;
+		bgmac->feature_flags |= BGMAC_FEAT_FORCE_SPEED_2500;
+	}
 
 	return bgmac_enet_probe(bgmac);
 }
diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
index 856379c..4584958 100644
--- a/drivers/net/ethernet/broadcom/bgmac.c
+++ b/drivers/net/ethernet/broadcom/bgmac.c
@@ -1388,7 +1388,7 @@ static const struct ethtool_ops bgmac_ethtool_ops = {
  * MII
  **************************************************/
 
-static void bgmac_adjust_link(struct net_device *net_dev)
+void bgmac_adjust_link(struct net_device *net_dev)
 {
 	struct bgmac *bgmac = netdev_priv(net_dev);
 	struct phy_device *phy_dev = net_dev->phydev;
@@ -1411,50 +1411,7 @@ static void bgmac_adjust_link(struct net_device *net_dev)
 		phy_print_status(phy_dev);
 	}
 }
-
-static int bgmac_phy_connect_direct(struct bgmac *bgmac)
-{
-	struct fixed_phy_status fphy_status = {
-		.link = 1,
-		.speed = SPEED_1000,
-		.duplex = DUPLEX_FULL,
-	};
-	struct phy_device *phy_dev;
-	int err;
-
-	phy_dev = fixed_phy_register(PHY_POLL, &fphy_status, -1, NULL);
-	if (!phy_dev || IS_ERR(phy_dev)) {
-		dev_err(bgmac->dev, "Failed to register fixed PHY device\n");
-		return -ENODEV;
-	}
-
-	err = phy_connect_direct(bgmac->net_dev, phy_dev, bgmac_adjust_link,
-				 PHY_INTERFACE_MODE_MII);
-	if (err) {
-		dev_err(bgmac->dev, "Connecting PHY failed\n");
-		return err;
-	}
-
-	return err;
-}
-
-static int bgmac_phy_connect(struct bgmac *bgmac)
-{
-	struct phy_device *phy_dev;
-	char bus_id[MII_BUS_ID_SIZE + 3];
-
-	/* Connect to the PHY */
-	snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id,
-		 bgmac->phyaddr);
-	phy_dev = phy_connect(bgmac->net_dev, bus_id, &bgmac_adjust_link,
-			      PHY_INTERFACE_MODE_MII);
-	if (IS_ERR(phy_dev)) {
-		dev_err(bgmac->dev, "PHY connecton failed\n");
-		return PTR_ERR(phy_dev);
-	}
-
-	return 0;
-}
+EXPORT_SYMBOL_GPL(bgmac_adjust_link);
 
 int bgmac_enet_probe(struct bgmac *info)
 {
@@ -1507,10 +1464,7 @@ int bgmac_enet_probe(struct bgmac *info)
 
 	netif_napi_add(net_dev, &bgmac->napi, bgmac_poll, BGMAC_WEIGHT);
 
-	if (!bgmac->mii_bus)
-		err = bgmac_phy_connect_direct(bgmac);
-	else
-		err = bgmac_phy_connect(bgmac);
+	err = bgmac_phy_connect(bgmac);
 	if (err) {
 		dev_err(bgmac->dev, "Cannot connect to phy\n");
 		goto err_dma_free;
diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
index 80836b4..ea52ac3 100644
--- a/drivers/net/ethernet/broadcom/bgmac.h
+++ b/drivers/net/ethernet/broadcom/bgmac.h
@@ -513,10 +513,12 @@ struct bgmac {
 	u32 (*get_bus_clock)(struct bgmac *bgmac);
 	void (*cmn_maskset32)(struct bgmac *bgmac, u16 offset, u32 mask,
 			      u32 set);
+	int (*phy_connect)(struct bgmac *bgmac);
 };
 
 int bgmac_enet_probe(struct bgmac *info);
 void bgmac_enet_remove(struct bgmac *bgmac);
+void bgmac_adjust_link(struct net_device *net_dev);
 
 struct mii_bus *bcma_mdio_mii_register(struct bcma_device *core, u8 phyaddr);
 void bcma_mdio_mii_unregister(struct mii_bus *mii_bus);
@@ -583,4 +585,9 @@ static inline void bgmac_set(struct bgmac *bgmac, u16 offset, u32 set)
 {
 	bgmac_maskset(bgmac, offset, ~0, set);
 }
+
+static inline int bgmac_phy_connect(struct bgmac *bgmac)
+{
+	return bgmac->phy_connect(bgmac);
+}
 #endif /* _BGMAC_H */
-- 
2.7.4

[PATCH v4 6/7] net: ethernet: bgmac: add NS2 support

[Jon Mason]

Add support for the variant of amac hardware present in the Broadcom
Northstar2 based SoCs.  Northstar2 requires an additional register to be
configured with the port speed/duplexity (NICPM).  This can be added to
the link callback to hide it from the instances that do not use this.
Also, clearing of the pending interrupts on init is required due to
observed issues on some platforms.

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++-
 drivers/net/ethernet/broadcom/bgmac.c          |  3 ++
 drivers/net/ethernet/broadcom/bgmac.h          |  1 +
 3 files changed, 58 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
index aed5dc5..f6d48c7 100644
--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
@@ -14,12 +14,21 @@
 #define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
 
 #include <linux/bcma/bcma.h>
+#include <linux/brcmphy.h>
 #include <linux/etherdevice.h>
 #include <linux/of_address.h>
 #include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include "bgmac.h"
 
+#define NICPM_IOMUX_CTRL		0x00000008
+
+#define NICPM_IOMUX_CTRL_INIT_VAL	0x3196e000
+#define NICPM_IOMUX_CTRL_SPD_SHIFT	10
+#define NICPM_IOMUX_CTRL_SPD_10M	0
+#define NICPM_IOMUX_CTRL_SPD_100M	1
+#define NICPM_IOMUX_CTRL_SPD_1000M	2
+
 static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
 {
 	return readl(bgmac->plat.base + offset);
@@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
 	WARN_ON(1);
 }
 
+static void bgmac_nicpm_speed_set(struct net_device *net_dev)
+{
+	struct bgmac *bgmac = netdev_priv(net_dev);
+	u32 val;
+
+	if (!bgmac->plat.nicpm_base)
+		return;
+
+	val = NICPM_IOMUX_CTRL_INIT_VAL;
+	switch (bgmac->net_dev->phydev->speed) {
+	default:
+		pr_err("Unsupported speed.  Defaulting to 1000Mb\n");
+	case SPEED_1000:
+		val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+		break;
+	case SPEED_100:
+		val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+		break;
+	case SPEED_10:
+		val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+		break;
+	}
+
+	writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
+
+	bgmac_adjust_link(bgmac->net_dev);
+}
+
 static int platform_phy_connect(struct bgmac *bgmac)
 {
 	struct phy_device *phy_dev;
 
-	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
-					 bgmac_adjust_link);
+	if (bgmac->plat.nicpm_base)
+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
+						 bgmac->dev->of_node,
+						 bgmac_nicpm_speed_set);
+	else
+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
+						 bgmac->dev->of_node,
+						 bgmac_adjust_link);
 	if (!phy_dev) {
 		dev_err(bgmac->dev, "Phy connect failed\n");
 		return -ENODEV;
@@ -182,6 +225,14 @@ static int bgmac_probe(struct platform_device *pdev)
 	if (IS_ERR(bgmac->plat.idm_base))
 		return PTR_ERR(bgmac->plat.idm_base);
 
+	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
+	if (regs) {
+		bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
+							       regs);
+		if (IS_ERR(bgmac->plat.nicpm_base))
+			return PTR_ERR(bgmac->plat.nicpm_base);
+	}
+
 	bgmac->read = platform_bgmac_read;
 	bgmac->write = platform_bgmac_write;
 	bgmac->idm_read = platform_bgmac_idm_read;
@@ -213,6 +264,7 @@ static int bgmac_remove(struct platform_device *pdev)
 static const struct of_device_id bgmac_of_enet_match[] = {
 	{.compatible = "brcm,amac",},
 	{.compatible = "brcm,nsp-amac",},
+	{.compatible = "brcm,ns2-amac",},
 	{},
 };
 
diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
index 4584958..a805cc8 100644
--- a/drivers/net/ethernet/broadcom/bgmac.c
+++ b/drivers/net/ethernet/broadcom/bgmac.c
@@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
 /* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
 static void bgmac_chip_init(struct bgmac *bgmac)
 {
+	/* Clear any erroneously pending interrupts */
+	bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
+
 	/* 1 interrupt per received frame */
 	bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
 
diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
index ea52ac3..b1820ea 100644
--- a/drivers/net/ethernet/broadcom/bgmac.h
+++ b/drivers/net/ethernet/broadcom/bgmac.h
@@ -463,6 +463,7 @@ struct bgmac {
 		struct {
 			void *base;
 			void *idm_base;
+			void *nicpm_base;
 		} plat;
 		struct {
 			struct bcma_device *core;
-- 
2.7.4

[PATCH v4 6/7] net: ethernet: bgmac: add NS2 support

[Jon Mason]

Add support for the variant of amac hardware present in the Broadcom
Northstar2 based SoCs.  Northstar2 requires an additional register to be
configured with the port speed/duplexity (NICPM).  This can be added to
the link callback to hide it from the instances that do not use this.
Also, clearing of the pending interrupts on init is required due to
observed issues on some platforms.

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++-
 drivers/net/ethernet/broadcom/bgmac.c          |  3 ++
 drivers/net/ethernet/broadcom/bgmac.h          |  1 +
 3 files changed, 58 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
index aed5dc5..f6d48c7 100644
--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
@@ -14,12 +14,21 @@
 #define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
 
 #include <linux/bcma/bcma.h>
+#include <linux/brcmphy.h>
 #include <linux/etherdevice.h>
 #include <linux/of_address.h>
 #include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include "bgmac.h"
 
+#define NICPM_IOMUX_CTRL		0x00000008
+
+#define NICPM_IOMUX_CTRL_INIT_VAL	0x3196e000
+#define NICPM_IOMUX_CTRL_SPD_SHIFT	10
+#define NICPM_IOMUX_CTRL_SPD_10M	0
+#define NICPM_IOMUX_CTRL_SPD_100M	1
+#define NICPM_IOMUX_CTRL_SPD_1000M	2
+
 static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
 {
 	return readl(bgmac->plat.base + offset);
@@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
 	WARN_ON(1);
 }
 
+static void bgmac_nicpm_speed_set(struct net_device *net_dev)
+{
+	struct bgmac *bgmac = netdev_priv(net_dev);
+	u32 val;
+
+	if (!bgmac->plat.nicpm_base)
+		return;
+
+	val = NICPM_IOMUX_CTRL_INIT_VAL;
+	switch (bgmac->net_dev->phydev->speed) {
+	default:
+		pr_err("Unsupported speed.  Defaulting to 1000Mb\n");
+	case SPEED_1000:
+		val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+		break;
+	case SPEED_100:
+		val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+		break;
+	case SPEED_10:
+		val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+		break;
+	}
+
+	writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
+
+	bgmac_adjust_link(bgmac->net_dev);
+}
+
 static int platform_phy_connect(struct bgmac *bgmac)
 {
 	struct phy_device *phy_dev;
 
-	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
-					 bgmac_adjust_link);
+	if (bgmac->plat.nicpm_base)
+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
+						 bgmac->dev->of_node,
+						 bgmac_nicpm_speed_set);
+	else
+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
+						 bgmac->dev->of_node,
+						 bgmac_adjust_link);
 	if (!phy_dev) {
 		dev_err(bgmac->dev, "Phy connect failed\n");
 		return -ENODEV;
@@ -182,6 +225,14 @@ static int bgmac_probe(struct platform_device *pdev)
 	if (IS_ERR(bgmac->plat.idm_base))
 		return PTR_ERR(bgmac->plat.idm_base);
 
+	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
+	if (regs) {
+		bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
+							       regs);
+		if (IS_ERR(bgmac->plat.nicpm_base))
+			return PTR_ERR(bgmac->plat.nicpm_base);
+	}
+
 	bgmac->read = platform_bgmac_read;
 	bgmac->write = platform_bgmac_write;
 	bgmac->idm_read = platform_bgmac_idm_read;
@@ -213,6 +264,7 @@ static int bgmac_remove(struct platform_device *pdev)
 static const struct of_device_id bgmac_of_enet_match[] = {
 	{.compatible = "brcm,amac",},
 	{.compatible = "brcm,nsp-amac",},
+	{.compatible = "brcm,ns2-amac",},
 	{},
 };
 
diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
index 4584958..a805cc8 100644
--- a/drivers/net/ethernet/broadcom/bgmac.c
+++ b/drivers/net/ethernet/broadcom/bgmac.c
@@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
 /* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
 static void bgmac_chip_init(struct bgmac *bgmac)
 {
+	/* Clear any erroneously pending interrupts */
+	bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
+
 	/* 1 interrupt per received frame */
 	bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
 
diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
index ea52ac3..b1820ea 100644
--- a/drivers/net/ethernet/broadcom/bgmac.h
+++ b/drivers/net/ethernet/broadcom/bgmac.h
@@ -463,6 +463,7 @@ struct bgmac {
 		struct {
 			void *base;
 			void *idm_base;
+			void *nicpm_base;
 		} plat;
 		struct {
 			struct bcma_device *core;
-- 
2.7.4

[PATCH v4 7/7] arm64: dts: NS2: add AMAC ethernet support

[Jon Mason]

Add support for the AMAC ethernet to the Broadcom Northstar2 SoC device
tree

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 arch/arm64/boot/dts/broadcom/ns2-svk.dts |  5 +++++
 arch/arm64/boot/dts/broadcom/ns2.dtsi    | 12 ++++++++++++
 2 files changed, 17 insertions(+)

diff --git a/arch/arm64/boot/dts/broadcom/ns2-svk.dts b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
index 2d7872a..2e4d90d 100644
--- a/arch/arm64/boot/dts/broadcom/ns2-svk.dts
+++ b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
@@ -56,6 +56,10 @@
 	};
 };
 
+&enet {
+	status = "ok";
+};
+
 &pci_phy0 {
 	status = "ok";
 };
@@ -172,6 +176,7 @@
 &mdio_mux_iproc {
 	mdio@10 {
 		gphy0: eth-phy@10 {
+			enet-phy-lane-swap;
 			reg = <0x10>;
 		};
 	};
diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi
index d95dc40..773ed59 100644
--- a/arch/arm64/boot/dts/broadcom/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi
@@ -191,6 +191,18 @@
 
 		#include "ns2-clock.dtsi"
 
+		enet: ethernet@61000000 {
+			compatible = "brcm,ns2-amac";
+			reg = <0x61000000 0x1000>,
+			      <0x61090000 0x1000>,
+			      <0x61030000 0x100>;
+			reg-names = "amac_base", "idm_base", "nicpm_base";
+			interrupts = <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>;
+			phy-handle = <&gphy0>;
+			phy-mode = "rgmii";
+			status = "disabled";
+		};
+
 		dma0: dma@61360000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x61360000 0x1000>;
-- 
2.7.4

[PATCH v4 7/7] arm64: dts: NS2: add AMAC ethernet support

[Jon Mason]

Add support for the AMAC ethernet to the Broadcom Northstar2 SoC device
tree

Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
 arch/arm64/boot/dts/broadcom/ns2-svk.dts |  5 +++++
 arch/arm64/boot/dts/broadcom/ns2.dtsi    | 12 ++++++++++++
 2 files changed, 17 insertions(+)

diff --git a/arch/arm64/boot/dts/broadcom/ns2-svk.dts b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
index 2d7872a..2e4d90d 100644
--- a/arch/arm64/boot/dts/broadcom/ns2-svk.dts
+++ b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
@@ -56,6 +56,10 @@
 	};
 };
 
+&enet {
+	status = "ok";
+};
+
 &pci_phy0 {
 	status = "ok";
 };
@@ -172,6 +176,7 @@
 &mdio_mux_iproc {
 	mdio at 10 {
 		gphy0: eth-phy at 10 {
+			enet-phy-lane-swap;
 			reg = <0x10>;
 		};
 	};
diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi
index d95dc40..773ed59 100644
--- a/arch/arm64/boot/dts/broadcom/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi
@@ -191,6 +191,18 @@
 
 		#include "ns2-clock.dtsi"
 
+		enet: ethernet at 61000000 {
+			compatible = "brcm,ns2-amac";
+			reg = <0x61000000 0x1000>,
+			      <0x61090000 0x1000>,
+			      <0x61030000 0x100>;
+			reg-names = "amac_base", "idm_base", "nicpm_base";
+			interrupts = <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>;
+			phy-handle = <&gphy0>;
+			phy-mode = "rgmii";
+			status = "disabled";
+		};
+
 		dma0: dma at 61360000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x61360000 0x1000>;
-- 
2.7.4

Re: [PATCH v4 6/7] net: ethernet: bgmac: add NS2 support

[Scott Branden]

One change in this patch

On 16-11-01 01:04 PM, Jon Mason wrote:
> Add support for the variant of amac hardware present in the Broadcom
> Northstar2 based SoCs.  Northstar2 requires an additional register to be
> configured with the port speed/duplexity (NICPM).  This can be added to
> the link callback to hide it from the instances that do not use this.
> Also, clearing of the pending interrupts on init is required due to
> observed issues on some platforms.
>
> Signed-off-by: Jon Mason <jon.mason@broadcom.com>
> ---
>  drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++-
>  drivers/net/ethernet/broadcom/bgmac.c          |  3 ++
>  drivers/net/ethernet/broadcom/bgmac.h          |  1 +
>  3 files changed, 58 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
> index aed5dc5..f6d48c7 100644
> --- a/drivers/net/ethernet/broadcom/bgmac-platform.c
> +++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
> @@ -14,12 +14,21 @@
>  #define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
>
>  #include <linux/bcma/bcma.h>
> +#include <linux/brcmphy.h>
>  #include <linux/etherdevice.h>
>  #include <linux/of_address.h>
>  #include <linux/of_mdio.h>
>  #include <linux/of_net.h>
>  #include "bgmac.h"
>
> +#define NICPM_IOMUX_CTRL		0x00000008
> +
> +#define NICPM_IOMUX_CTRL_INIT_VAL	0x3196e000
> +#define NICPM_IOMUX_CTRL_SPD_SHIFT	10
> +#define NICPM_IOMUX_CTRL_SPD_10M	0
> +#define NICPM_IOMUX_CTRL_SPD_100M	1
> +#define NICPM_IOMUX_CTRL_SPD_1000M	2
> +
>  static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
>  {
>  	return readl(bgmac->plat.base + offset);
> @@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
>  	WARN_ON(1);
>  }
>
> +static void bgmac_nicpm_speed_set(struct net_device *net_dev)
> +{
> +	struct bgmac *bgmac = netdev_priv(net_dev);
> +	u32 val;
> +
> +	if (!bgmac->plat.nicpm_base)
> +		return;
> +
> +	val = NICPM_IOMUX_CTRL_INIT_VAL;
> +	switch (bgmac->net_dev->phydev->speed) {
> +	default:
> +		pr_err("Unsupported speed.  Defaulting to 1000Mb\n");
This should be dev_err
> +	case SPEED_1000:
> +		val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> +		break;
> +	case SPEED_100:
> +		val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> +		break;
> +	case SPEED_10:
> +		val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> +		break;
> +	}
> +
> +	writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
> +
> +	bgmac_adjust_link(bgmac->net_dev);
> +}
> +
>  static int platform_phy_connect(struct bgmac *bgmac)
>  {
>  	struct phy_device *phy_dev;
>
> -	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
> -					 bgmac_adjust_link);
> +	if (bgmac->plat.nicpm_base)
> +		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> +						 bgmac->dev->of_node,
> +						 bgmac_nicpm_speed_set);
> +	else
> +		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> +						 bgmac->dev->of_node,
> +						 bgmac_adjust_link);
>  	if (!phy_dev) {
>  		dev_err(bgmac->dev, "Phy connect failed\n");
>  		return -ENODEV;
> @@ -182,6 +225,14 @@ static int bgmac_probe(struct platform_device *pdev)
>  	if (IS_ERR(bgmac->plat.idm_base))
>  		return PTR_ERR(bgmac->plat.idm_base);
>
> +	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
> +	if (regs) {
> +		bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
> +							       regs);
> +		if (IS_ERR(bgmac->plat.nicpm_base))
> +			return PTR_ERR(bgmac->plat.nicpm_base);
> +	}
> +
>  	bgmac->read = platform_bgmac_read;
>  	bgmac->write = platform_bgmac_write;
>  	bgmac->idm_read = platform_bgmac_idm_read;
> @@ -213,6 +264,7 @@ static int bgmac_remove(struct platform_device *pdev)
>  static const struct of_device_id bgmac_of_enet_match[] = {
>  	{.compatible = "brcm,amac",},
>  	{.compatible = "brcm,nsp-amac",},
> +	{.compatible = "brcm,ns2-amac",},
>  	{},
>  };
>
> diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
> index 4584958..a805cc8 100644
> --- a/drivers/net/ethernet/broadcom/bgmac.c
> +++ b/drivers/net/ethernet/broadcom/bgmac.c
> @@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
>  /* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
>  static void bgmac_chip_init(struct bgmac *bgmac)
>  {
> +	/* Clear any erroneously pending interrupts */
> +	bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
> +
>  	/* 1 interrupt per received frame */
>  	bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
>
> diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
> index ea52ac3..b1820ea 100644
> --- a/drivers/net/ethernet/broadcom/bgmac.h
> +++ b/drivers/net/ethernet/broadcom/bgmac.h
> @@ -463,6 +463,7 @@ struct bgmac {
>  		struct {
>  			void *base;
>  			void *idm_base;
> +			void *nicpm_base;
>  		} plat;
>  		struct {
>  			struct bcma_device *core;
>

[PATCH v4 6/7] net: ethernet: bgmac: add NS2 support

[Scott Branden]

One change in this patch

On 16-11-01 01:04 PM, Jon Mason wrote:
> Add support for the variant of amac hardware present in the Broadcom
> Northstar2 based SoCs.  Northstar2 requires an additional register to be
> configured with the port speed/duplexity (NICPM).  This can be added to
> the link callback to hide it from the instances that do not use this.
> Also, clearing of the pending interrupts on init is required due to
> observed issues on some platforms.
>
> Signed-off-by: Jon Mason <jon.mason@broadcom.com>
> ---
>  drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++-
>  drivers/net/ethernet/broadcom/bgmac.c          |  3 ++
>  drivers/net/ethernet/broadcom/bgmac.h          |  1 +
>  3 files changed, 58 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
> index aed5dc5..f6d48c7 100644
> --- a/drivers/net/ethernet/broadcom/bgmac-platform.c
> +++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
> @@ -14,12 +14,21 @@
>  #define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
>
>  #include <linux/bcma/bcma.h>
> +#include <linux/brcmphy.h>
>  #include <linux/etherdevice.h>
>  #include <linux/of_address.h>
>  #include <linux/of_mdio.h>
>  #include <linux/of_net.h>
>  #include "bgmac.h"
>
> +#define NICPM_IOMUX_CTRL		0x00000008
> +
> +#define NICPM_IOMUX_CTRL_INIT_VAL	0x3196e000
> +#define NICPM_IOMUX_CTRL_SPD_SHIFT	10
> +#define NICPM_IOMUX_CTRL_SPD_10M	0
> +#define NICPM_IOMUX_CTRL_SPD_100M	1
> +#define NICPM_IOMUX_CTRL_SPD_1000M	2
> +
>  static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
>  {
>  	return readl(bgmac->plat.base + offset);
> @@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
>  	WARN_ON(1);
>  }
>
> +static void bgmac_nicpm_speed_set(struct net_device *net_dev)
> +{
> +	struct bgmac *bgmac = netdev_priv(net_dev);
> +	u32 val;
> +
> +	if (!bgmac->plat.nicpm_base)
> +		return;
> +
> +	val = NICPM_IOMUX_CTRL_INIT_VAL;
> +	switch (bgmac->net_dev->phydev->speed) {
> +	default:
> +		pr_err("Unsupported speed.  Defaulting to 1000Mb\n");
This should be dev_err
> +	case SPEED_1000:
> +		val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> +		break;
> +	case SPEED_100:
> +		val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> +		break;
> +	case SPEED_10:
> +		val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> +		break;
> +	}
> +
> +	writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
> +
> +	bgmac_adjust_link(bgmac->net_dev);
> +}
> +
>  static int platform_phy_connect(struct bgmac *bgmac)
>  {
>  	struct phy_device *phy_dev;
>
> -	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
> -					 bgmac_adjust_link);
> +	if (bgmac->plat.nicpm_base)
> +		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> +						 bgmac->dev->of_node,
> +						 bgmac_nicpm_speed_set);
> +	else
> +		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> +						 bgmac->dev->of_node,
> +						 bgmac_adjust_link);
>  	if (!phy_dev) {
>  		dev_err(bgmac->dev, "Phy connect failed\n");
>  		return -ENODEV;
> @@ -182,6 +225,14 @@ static int bgmac_probe(struct platform_device *pdev)
>  	if (IS_ERR(bgmac->plat.idm_base))
>  		return PTR_ERR(bgmac->plat.idm_base);
>
> +	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
> +	if (regs) {
> +		bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
> +							       regs);
> +		if (IS_ERR(bgmac->plat.nicpm_base))
> +			return PTR_ERR(bgmac->plat.nicpm_base);
> +	}
> +
>  	bgmac->read = platform_bgmac_read;
>  	bgmac->write = platform_bgmac_write;
>  	bgmac->idm_read = platform_bgmac_idm_read;
> @@ -213,6 +264,7 @@ static int bgmac_remove(struct platform_device *pdev)
>  static const struct of_device_id bgmac_of_enet_match[] = {
>  	{.compatible = "brcm,amac",},
>  	{.compatible = "brcm,nsp-amac",},
> +	{.compatible = "brcm,ns2-amac",},
>  	{},
>  };
>
> diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
> index 4584958..a805cc8 100644
> --- a/drivers/net/ethernet/broadcom/bgmac.c
> +++ b/drivers/net/ethernet/broadcom/bgmac.c
> @@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
>  /* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
>  static void bgmac_chip_init(struct bgmac *bgmac)
>  {
> +	/* Clear any erroneously pending interrupts */
> +	bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
> +
>  	/* 1 interrupt per received frame */
>  	bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
>
> diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
> index ea52ac3..b1820ea 100644
> --- a/drivers/net/ethernet/broadcom/bgmac.h
> +++ b/drivers/net/ethernet/broadcom/bgmac.h
> @@ -463,6 +463,7 @@ struct bgmac {
>  		struct {
>  			void *base;
>  			void *idm_base;
> +			void *nicpm_base;
>  		} plat;
>  		struct {
>  			struct bcma_device *core;
>

Re: [PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Andrew Lunn]

> +- enet-phy-lane-swap: If set, indicates the PHY device requires swapping the
> +  TX/RX lanes to function properly.

Is 'requires' the right word here? The PHY performs the actual swap of
the Tx/Rx lanes.

    Andrew

Re: [PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Andrew Lunn]

> +- enet-phy-lane-swap: If set, indicates the PHY device requires swapping the
> +  TX/RX lanes to function properly.

Is 'requires' the right word here? The PHY performs the actual swap of
the Tx/Rx lanes.

    Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Andrew Lunn]

> +- enet-phy-lane-swap: If set, indicates the PHY device requires swapping the
> +  TX/RX lanes to function properly.

Is 'requires' the right word here? The PHY performs the actual swap of
the Tx/Rx lanes.

    Andrew

Re: [PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Jon Mason]

On Tue, Nov 01, 2016 at 09:48:26PM +0100, Andrew Lunn wrote:
> > +- enet-phy-lane-swap: If set, indicates the PHY device requires swapping the
> > +  TX/RX lanes to function properly.
> 
> Is 'requires' the right word here? The PHY performs the actual swap of
> the Tx/Rx lanes.

What I'm trying to say here is that without the lane swapping, the PHY
will not function properly.  Thus, those PHYs require this parameter
to work.  I am open to suggestions to reword the sentence to make it
clearer.

Thanks,
Jon

> 
>     Andrew

Re: [PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Jon Mason]

On Tue, Nov 01, 2016 at 09:48:26PM +0100, Andrew Lunn wrote:
> > +- enet-phy-lane-swap: If set, indicates the PHY device requires swapping the
> > +  TX/RX lanes to function properly.
> 
> Is 'requires' the right word here? The PHY performs the actual swap of
> the Tx/Rx lanes.

What I'm trying to say here is that without the lane swapping, the PHY
will not function properly.  Thus, those PHYs require this parameter
to work.  I am open to suggestions to reword the sentence to make it
clearer.

Thanks,
Jon

> 
>     Andrew
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Jon Mason]

On Tue, Nov 01, 2016 at 09:48:26PM +0100, Andrew Lunn wrote:
> > +- enet-phy-lane-swap: If set, indicates the PHY device requires swapping the
> > +  TX/RX lanes to function properly.
> 
> Is 'requires' the right word here? The PHY performs the actual swap of
> the Tx/Rx lanes.

What I'm trying to say here is that without the lane swapping, the PHY
will not function properly.  Thus, those PHYs require this parameter
to work.  I am open to suggestions to reword the sentence to make it
clearer.

Thanks,
Jon

> 
>     Andrew

Re: [PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Scott Branden]

On 16-11-01 01:59 PM, Jon Mason wrote:
> On Tue, Nov 01, 2016 at 09:48:26PM +0100, Andrew Lunn wrote:
>>> +- enet-phy-lane-swap: If set, indicates the PHY device requires swapping the
>>> +  TX/RX lanes to function properly.
>>
>> Is 'requires' the right word here? The PHY performs the actual swap of
>> the Tx/Rx lanes.
>
> What I'm trying to say here is that without the lane swapping, the PHY
> will not function properly.  Thus, those PHYs require this parameter
> to work.  I am open to suggestions to reword the sentence to make it
> clearer.
If set, indicates the PHY will swap the TX/RX lanes to compensate for 
the board being designed with the lanes swapped.
>
> Thanks,
> Jon
>
>>
>>     Andrew

[PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Scott Branden]

On 16-11-01 01:59 PM, Jon Mason wrote:
> On Tue, Nov 01, 2016 at 09:48:26PM +0100, Andrew Lunn wrote:
>>> +- enet-phy-lane-swap: If set, indicates the PHY device requires swapping the
>>> +  TX/RX lanes to function properly.
>>
>> Is 'requires' the right word here? The PHY performs the actual swap of
>> the Tx/Rx lanes.
>
> What I'm trying to say here is that without the lane swapping, the PHY
> will not function properly.  Thus, those PHYs require this parameter
> to work.  I am open to suggestions to reword the sentence to make it
> clearer.
If set, indicates the PHY will swap the TX/RX lanes to compensate for 
the board being designed with the lanes swapped.
>
> Thanks,
> Jon
>
>>
>>     Andrew

Re: [PATCH v4 6/7] net: ethernet: bgmac: add NS2 support

[Jon Mason]

On Tue, Nov 01, 2016 at 01:34:30PM -0700, Scott Branden wrote:
> One change in this patch
> 
> On 16-11-01 01:04 PM, Jon Mason wrote:
> >Add support for the variant of amac hardware present in the Broadcom
> >Northstar2 based SoCs.  Northstar2 requires an additional register to be
> >configured with the port speed/duplexity (NICPM).  This can be added to
> >the link callback to hide it from the instances that do not use this.
> >Also, clearing of the pending interrupts on init is required due to
> >observed issues on some platforms.
> >
> >Signed-off-by: Jon Mason <jon.mason@broadcom.com>
> >---
> > drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++-
> > drivers/net/ethernet/broadcom/bgmac.c          |  3 ++
> > drivers/net/ethernet/broadcom/bgmac.h          |  1 +
> > 3 files changed, 58 insertions(+), 2 deletions(-)
> >
> >diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
> >index aed5dc5..f6d48c7 100644
> >--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
> >+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
> >@@ -14,12 +14,21 @@
> > #define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
> >
> > #include <linux/bcma/bcma.h>
> >+#include <linux/brcmphy.h>
> > #include <linux/etherdevice.h>
> > #include <linux/of_address.h>
> > #include <linux/of_mdio.h>
> > #include <linux/of_net.h>
> > #include "bgmac.h"
> >
> >+#define NICPM_IOMUX_CTRL		0x00000008
> >+
> >+#define NICPM_IOMUX_CTRL_INIT_VAL	0x3196e000
> >+#define NICPM_IOMUX_CTRL_SPD_SHIFT	10
> >+#define NICPM_IOMUX_CTRL_SPD_10M	0
> >+#define NICPM_IOMUX_CTRL_SPD_100M	1
> >+#define NICPM_IOMUX_CTRL_SPD_1000M	2
> >+
> > static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
> > {
> > 	return readl(bgmac->plat.base + offset);
> >@@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
> > 	WARN_ON(1);
> > }
> >
> >+static void bgmac_nicpm_speed_set(struct net_device *net_dev)
> >+{
> >+	struct bgmac *bgmac = netdev_priv(net_dev);
> >+	u32 val;
> >+
> >+	if (!bgmac->plat.nicpm_base)
> >+		return;
> >+
> >+	val = NICPM_IOMUX_CTRL_INIT_VAL;
> >+	switch (bgmac->net_dev->phydev->speed) {
> >+	default:
> >+		pr_err("Unsupported speed.  Defaulting to 1000Mb\n");
> This should be dev_err

It should probably be netdev_err (and there are a few instances below
that should probably be changed to netdev_err as well).

Thanks,
Jon

> >+	case SPEED_1000:
> >+		val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> >+		break;
> >+	case SPEED_100:
> >+		val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> >+		break;
> >+	case SPEED_10:
> >+		val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> >+		break;
> >+	}
> >+
> >+	writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
> >+
> >+	bgmac_adjust_link(bgmac->net_dev);
> >+}
> >+
> > static int platform_phy_connect(struct bgmac *bgmac)
> > {
> > 	struct phy_device *phy_dev;
> >
> >-	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
> >-					 bgmac_adjust_link);
> >+	if (bgmac->plat.nicpm_base)
> >+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> >+						 bgmac->dev->of_node,
> >+						 bgmac_nicpm_speed_set);
> >+	else
> >+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> >+						 bgmac->dev->of_node,
> >+						 bgmac_adjust_link);
> > 	if (!phy_dev) {
> > 		dev_err(bgmac->dev, "Phy connect failed\n");
> > 		return -ENODEV;
> >@@ -182,6 +225,14 @@ static int bgmac_probe(struct platform_device *pdev)
> > 	if (IS_ERR(bgmac->plat.idm_base))
> > 		return PTR_ERR(bgmac->plat.idm_base);
> >
> >+	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
> >+	if (regs) {
> >+		bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
> >+							       regs);
> >+		if (IS_ERR(bgmac->plat.nicpm_base))
> >+			return PTR_ERR(bgmac->plat.nicpm_base);
> >+	}
> >+
> > 	bgmac->read = platform_bgmac_read;
> > 	bgmac->write = platform_bgmac_write;
> > 	bgmac->idm_read = platform_bgmac_idm_read;
> >@@ -213,6 +264,7 @@ static int bgmac_remove(struct platform_device *pdev)
> > static const struct of_device_id bgmac_of_enet_match[] = {
> > 	{.compatible = "brcm,amac",},
> > 	{.compatible = "brcm,nsp-amac",},
> >+	{.compatible = "brcm,ns2-amac",},
> > 	{},
> > };
> >
> >diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
> >index 4584958..a805cc8 100644
> >--- a/drivers/net/ethernet/broadcom/bgmac.c
> >+++ b/drivers/net/ethernet/broadcom/bgmac.c
> >@@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
> > /* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
> > static void bgmac_chip_init(struct bgmac *bgmac)
> > {
> >+	/* Clear any erroneously pending interrupts */
> >+	bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
> >+
> > 	/* 1 interrupt per received frame */
> > 	bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
> >
> >diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
> >index ea52ac3..b1820ea 100644
> >--- a/drivers/net/ethernet/broadcom/bgmac.h
> >+++ b/drivers/net/ethernet/broadcom/bgmac.h
> >@@ -463,6 +463,7 @@ struct bgmac {
> > 		struct {
> > 			void *base;
> > 			void *idm_base;
> >+			void *nicpm_base;
> > 		} plat;
> > 		struct {
> > 			struct bcma_device *core;
> >

[PATCH v4 6/7] net: ethernet: bgmac: add NS2 support

[Jon Mason]

On Tue, Nov 01, 2016 at 01:34:30PM -0700, Scott Branden wrote:
> One change in this patch
> 
> On 16-11-01 01:04 PM, Jon Mason wrote:
> >Add support for the variant of amac hardware present in the Broadcom
> >Northstar2 based SoCs.  Northstar2 requires an additional register to be
> >configured with the port speed/duplexity (NICPM).  This can be added to
> >the link callback to hide it from the instances that do not use this.
> >Also, clearing of the pending interrupts on init is required due to
> >observed issues on some platforms.
> >
> >Signed-off-by: Jon Mason <jon.mason@broadcom.com>
> >---
> > drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++-
> > drivers/net/ethernet/broadcom/bgmac.c          |  3 ++
> > drivers/net/ethernet/broadcom/bgmac.h          |  1 +
> > 3 files changed, 58 insertions(+), 2 deletions(-)
> >
> >diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
> >index aed5dc5..f6d48c7 100644
> >--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
> >+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
> >@@ -14,12 +14,21 @@
> > #define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
> >
> > #include <linux/bcma/bcma.h>
> >+#include <linux/brcmphy.h>
> > #include <linux/etherdevice.h>
> > #include <linux/of_address.h>
> > #include <linux/of_mdio.h>
> > #include <linux/of_net.h>
> > #include "bgmac.h"
> >
> >+#define NICPM_IOMUX_CTRL		0x00000008
> >+
> >+#define NICPM_IOMUX_CTRL_INIT_VAL	0x3196e000
> >+#define NICPM_IOMUX_CTRL_SPD_SHIFT	10
> >+#define NICPM_IOMUX_CTRL_SPD_10M	0
> >+#define NICPM_IOMUX_CTRL_SPD_100M	1
> >+#define NICPM_IOMUX_CTRL_SPD_1000M	2
> >+
> > static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
> > {
> > 	return readl(bgmac->plat.base + offset);
> >@@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
> > 	WARN_ON(1);
> > }
> >
> >+static void bgmac_nicpm_speed_set(struct net_device *net_dev)
> >+{
> >+	struct bgmac *bgmac = netdev_priv(net_dev);
> >+	u32 val;
> >+
> >+	if (!bgmac->plat.nicpm_base)
> >+		return;
> >+
> >+	val = NICPM_IOMUX_CTRL_INIT_VAL;
> >+	switch (bgmac->net_dev->phydev->speed) {
> >+	default:
> >+		pr_err("Unsupported speed.  Defaulting to 1000Mb\n");
> This should be dev_err

It should probably be netdev_err (and there are a few instances below
that should probably be changed to netdev_err as well).

Thanks,
Jon

> >+	case SPEED_1000:
> >+		val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> >+		break;
> >+	case SPEED_100:
> >+		val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> >+		break;
> >+	case SPEED_10:
> >+		val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> >+		break;
> >+	}
> >+
> >+	writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
> >+
> >+	bgmac_adjust_link(bgmac->net_dev);
> >+}
> >+
> > static int platform_phy_connect(struct bgmac *bgmac)
> > {
> > 	struct phy_device *phy_dev;
> >
> >-	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
> >-					 bgmac_adjust_link);
> >+	if (bgmac->plat.nicpm_base)
> >+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> >+						 bgmac->dev->of_node,
> >+						 bgmac_nicpm_speed_set);
> >+	else
> >+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> >+						 bgmac->dev->of_node,
> >+						 bgmac_adjust_link);
> > 	if (!phy_dev) {
> > 		dev_err(bgmac->dev, "Phy connect failed\n");
> > 		return -ENODEV;
> >@@ -182,6 +225,14 @@ static int bgmac_probe(struct platform_device *pdev)
> > 	if (IS_ERR(bgmac->plat.idm_base))
> > 		return PTR_ERR(bgmac->plat.idm_base);
> >
> >+	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
> >+	if (regs) {
> >+		bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
> >+							       regs);
> >+		if (IS_ERR(bgmac->plat.nicpm_base))
> >+			return PTR_ERR(bgmac->plat.nicpm_base);
> >+	}
> >+
> > 	bgmac->read = platform_bgmac_read;
> > 	bgmac->write = platform_bgmac_write;
> > 	bgmac->idm_read = platform_bgmac_idm_read;
> >@@ -213,6 +264,7 @@ static int bgmac_remove(struct platform_device *pdev)
> > static const struct of_device_id bgmac_of_enet_match[] = {
> > 	{.compatible = "brcm,amac",},
> > 	{.compatible = "brcm,nsp-amac",},
> >+	{.compatible = "brcm,ns2-amac",},
> > 	{},
> > };
> >
> >diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
> >index 4584958..a805cc8 100644
> >--- a/drivers/net/ethernet/broadcom/bgmac.c
> >+++ b/drivers/net/ethernet/broadcom/bgmac.c
> >@@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
> > /* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
> > static void bgmac_chip_init(struct bgmac *bgmac)
> > {
> >+	/* Clear any erroneously pending interrupts */
> >+	bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
> >+
> > 	/* 1 interrupt per received frame */
> > 	bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
> >
> >diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
> >index ea52ac3..b1820ea 100644
> >--- a/drivers/net/ethernet/broadcom/bgmac.h
> >+++ b/drivers/net/ethernet/broadcom/bgmac.h
> >@@ -463,6 +463,7 @@ struct bgmac {
> > 		struct {
> > 			void *base;
> > 			void *idm_base;
> >+			void *nicpm_base;
> > 		} plat;
> > 		struct {
> > 			struct bcma_device *core;
> >

Re: [PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Andrew Lunn]

> If set, indicates the PHY will swap the TX/RX lanes to compensate
> for the board being designed with the lanes swapped.

Thanks, much better.

	Andrew

Re: [PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Andrew Lunn]

> If set, indicates the PHY will swap the TX/RX lanes to compensate
> for the board being designed with the lanes swapped.

Thanks, much better.

	Andrew

[PATCH v4 2/7] Documentation: devicetree: add PHY lane swap binding

[Andrew Lunn]

> If set, indicates the PHY will swap the TX/RX lanes to compensate
> for the board being designed with the lanes swapped.

Thanks, much better.

	Andrew

Re: [PATCH v4 6/7] net: ethernet: bgmac: add NS2 support

[Jon Mason]

On Tue, Nov 01, 2016 at 05:05:13PM -0400, Jon Mason wrote:
> On Tue, Nov 01, 2016 at 01:34:30PM -0700, Scott Branden wrote:
> > One change in this patch
> > 
> > On 16-11-01 01:04 PM, Jon Mason wrote:
> > >Add support for the variant of amac hardware present in the Broadcom
> > >Northstar2 based SoCs.  Northstar2 requires an additional register to be
> > >configured with the port speed/duplexity (NICPM).  This can be added to
> > >the link callback to hide it from the instances that do not use this.
> > >Also, clearing of the pending interrupts on init is required due to
> > >observed issues on some platforms.
> > >
> > >Signed-off-by: Jon Mason <jon.mason@broadcom.com>
> > >---
> > > drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++-
> > > drivers/net/ethernet/broadcom/bgmac.c          |  3 ++
> > > drivers/net/ethernet/broadcom/bgmac.h          |  1 +
> > > 3 files changed, 58 insertions(+), 2 deletions(-)
> > >
> > >diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
> > >index aed5dc5..f6d48c7 100644
> > >--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
> > >+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
> > >@@ -14,12 +14,21 @@
> > > #define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
> > >
> > > #include <linux/bcma/bcma.h>
> > >+#include <linux/brcmphy.h>
> > > #include <linux/etherdevice.h>
> > > #include <linux/of_address.h>
> > > #include <linux/of_mdio.h>
> > > #include <linux/of_net.h>
> > > #include "bgmac.h"
> > >
> > >+#define NICPM_IOMUX_CTRL		0x00000008
> > >+
> > >+#define NICPM_IOMUX_CTRL_INIT_VAL	0x3196e000
> > >+#define NICPM_IOMUX_CTRL_SPD_SHIFT	10
> > >+#define NICPM_IOMUX_CTRL_SPD_10M	0
> > >+#define NICPM_IOMUX_CTRL_SPD_100M	1
> > >+#define NICPM_IOMUX_CTRL_SPD_1000M	2
> > >+
> > > static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
> > > {
> > > 	return readl(bgmac->plat.base + offset);
> > >@@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
> > > 	WARN_ON(1);
> > > }
> > >
> > >+static void bgmac_nicpm_speed_set(struct net_device *net_dev)
> > >+{
> > >+	struct bgmac *bgmac = netdev_priv(net_dev);
> > >+	u32 val;
> > >+
> > >+	if (!bgmac->plat.nicpm_base)
> > >+		return;
> > >+
> > >+	val = NICPM_IOMUX_CTRL_INIT_VAL;
> > >+	switch (bgmac->net_dev->phydev->speed) {
> > >+	default:
> > >+		pr_err("Unsupported speed.  Defaulting to 1000Mb\n");
> > This should be dev_err
> 
> It should probably be netdev_err (and there are a few instances below
> that should probably be changed to netdev_err as well).

Actually, the other instances I referenced above should not be
netdev_err, as they are enountered before the netdev is created.  So,
dev_err is correct for them.

That being said, the original pr_err that Scott referenced should be
netdev_err (as it is encountered after the netdev is created).  v5 will
make that change.

Thanks,
Jon

> 
> Thanks,
> Jon
> 
> > >+	case SPEED_1000:
> > >+		val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> > >+		break;
> > >+	case SPEED_100:
> > >+		val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> > >+		break;
> > >+	case SPEED_10:
> > >+		val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> > >+		break;
> > >+	}
> > >+
> > >+	writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
> > >+
> > >+	bgmac_adjust_link(bgmac->net_dev);
> > >+}
> > >+
> > > static int platform_phy_connect(struct bgmac *bgmac)
> > > {
> > > 	struct phy_device *phy_dev;
> > >
> > >-	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
> > >-					 bgmac_adjust_link);
> > >+	if (bgmac->plat.nicpm_base)
> > >+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> > >+						 bgmac->dev->of_node,
> > >+						 bgmac_nicpm_speed_set);
> > >+	else
> > >+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> > >+						 bgmac->dev->of_node,
> > >+						 bgmac_adjust_link);
> > > 	if (!phy_dev) {
> > > 		dev_err(bgmac->dev, "Phy connect failed\n");
> > > 		return -ENODEV;
> > >@@ -182,6 +225,14 @@ static int bgmac_probe(struct platform_device *pdev)
> > > 	if (IS_ERR(bgmac->plat.idm_base))
> > > 		return PTR_ERR(bgmac->plat.idm_base);
> > >
> > >+	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
> > >+	if (regs) {
> > >+		bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
> > >+							       regs);
> > >+		if (IS_ERR(bgmac->plat.nicpm_base))
> > >+			return PTR_ERR(bgmac->plat.nicpm_base);
> > >+	}
> > >+
> > > 	bgmac->read = platform_bgmac_read;
> > > 	bgmac->write = platform_bgmac_write;
> > > 	bgmac->idm_read = platform_bgmac_idm_read;
> > >@@ -213,6 +264,7 @@ static int bgmac_remove(struct platform_device *pdev)
> > > static const struct of_device_id bgmac_of_enet_match[] = {
> > > 	{.compatible = "brcm,amac",},
> > > 	{.compatible = "brcm,nsp-amac",},
> > >+	{.compatible = "brcm,ns2-amac",},
> > > 	{},
> > > };
> > >
> > >diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
> > >index 4584958..a805cc8 100644
> > >--- a/drivers/net/ethernet/broadcom/bgmac.c
> > >+++ b/drivers/net/ethernet/broadcom/bgmac.c
> > >@@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
> > > /* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
> > > static void bgmac_chip_init(struct bgmac *bgmac)
> > > {
> > >+	/* Clear any erroneously pending interrupts */
> > >+	bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
> > >+
> > > 	/* 1 interrupt per received frame */
> > > 	bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
> > >
> > >diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
> > >index ea52ac3..b1820ea 100644
> > >--- a/drivers/net/ethernet/broadcom/bgmac.h
> > >+++ b/drivers/net/ethernet/broadcom/bgmac.h
> > >@@ -463,6 +463,7 @@ struct bgmac {
> > > 		struct {
> > > 			void *base;
> > > 			void *idm_base;
> > >+			void *nicpm_base;
> > > 		} plat;
> > > 		struct {
> > > 			struct bcma_device *core;
> > >

[PATCH v4 6/7] net: ethernet: bgmac: add NS2 support

[Jon Mason]

On Tue, Nov 01, 2016 at 05:05:13PM -0400, Jon Mason wrote:
> On Tue, Nov 01, 2016 at 01:34:30PM -0700, Scott Branden wrote:
> > One change in this patch
> > 
> > On 16-11-01 01:04 PM, Jon Mason wrote:
> > >Add support for the variant of amac hardware present in the Broadcom
> > >Northstar2 based SoCs.  Northstar2 requires an additional register to be
> > >configured with the port speed/duplexity (NICPM).  This can be added to
> > >the link callback to hide it from the instances that do not use this.
> > >Also, clearing of the pending interrupts on init is required due to
> > >observed issues on some platforms.
> > >
> > >Signed-off-by: Jon Mason <jon.mason@broadcom.com>
> > >---
> > > drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++-
> > > drivers/net/ethernet/broadcom/bgmac.c          |  3 ++
> > > drivers/net/ethernet/broadcom/bgmac.h          |  1 +
> > > 3 files changed, 58 insertions(+), 2 deletions(-)
> > >
> > >diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
> > >index aed5dc5..f6d48c7 100644
> > >--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
> > >+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
> > >@@ -14,12 +14,21 @@
> > > #define pr_fmt(fmt)		KBUILD_MODNAME ": " fmt
> > >
> > > #include <linux/bcma/bcma.h>
> > >+#include <linux/brcmphy.h>
> > > #include <linux/etherdevice.h>
> > > #include <linux/of_address.h>
> > > #include <linux/of_mdio.h>
> > > #include <linux/of_net.h>
> > > #include "bgmac.h"
> > >
> > >+#define NICPM_IOMUX_CTRL		0x00000008
> > >+
> > >+#define NICPM_IOMUX_CTRL_INIT_VAL	0x3196e000
> > >+#define NICPM_IOMUX_CTRL_SPD_SHIFT	10
> > >+#define NICPM_IOMUX_CTRL_SPD_10M	0
> > >+#define NICPM_IOMUX_CTRL_SPD_100M	1
> > >+#define NICPM_IOMUX_CTRL_SPD_1000M	2
> > >+
> > > static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
> > > {
> > > 	return readl(bgmac->plat.base + offset);
> > >@@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
> > > 	WARN_ON(1);
> > > }
> > >
> > >+static void bgmac_nicpm_speed_set(struct net_device *net_dev)
> > >+{
> > >+	struct bgmac *bgmac = netdev_priv(net_dev);
> > >+	u32 val;
> > >+
> > >+	if (!bgmac->plat.nicpm_base)
> > >+		return;
> > >+
> > >+	val = NICPM_IOMUX_CTRL_INIT_VAL;
> > >+	switch (bgmac->net_dev->phydev->speed) {
> > >+	default:
> > >+		pr_err("Unsupported speed.  Defaulting to 1000Mb\n");
> > This should be dev_err
> 
> It should probably be netdev_err (and there are a few instances below
> that should probably be changed to netdev_err as well).

Actually, the other instances I referenced above should not be
netdev_err, as they are enountered before the netdev is created.  So,
dev_err is correct for them.

That being said, the original pr_err that Scott referenced should be
netdev_err (as it is encountered after the netdev is created).  v5 will
make that change.

Thanks,
Jon

> 
> Thanks,
> Jon
> 
> > >+	case SPEED_1000:
> > >+		val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> > >+		break;
> > >+	case SPEED_100:
> > >+		val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> > >+		break;
> > >+	case SPEED_10:
> > >+		val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> > >+		break;
> > >+	}
> > >+
> > >+	writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
> > >+
> > >+	bgmac_adjust_link(bgmac->net_dev);
> > >+}
> > >+
> > > static int platform_phy_connect(struct bgmac *bgmac)
> > > {
> > > 	struct phy_device *phy_dev;
> > >
> > >-	phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
> > >-					 bgmac_adjust_link);
> > >+	if (bgmac->plat.nicpm_base)
> > >+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> > >+						 bgmac->dev->of_node,
> > >+						 bgmac_nicpm_speed_set);
> > >+	else
> > >+		phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> > >+						 bgmac->dev->of_node,
> > >+						 bgmac_adjust_link);
> > > 	if (!phy_dev) {
> > > 		dev_err(bgmac->dev, "Phy connect failed\n");
> > > 		return -ENODEV;
> > >@@ -182,6 +225,14 @@ static int bgmac_probe(struct platform_device *pdev)
> > > 	if (IS_ERR(bgmac->plat.idm_base))
> > > 		return PTR_ERR(bgmac->plat.idm_base);
> > >
> > >+	regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
> > >+	if (regs) {
> > >+		bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
> > >+							       regs);
> > >+		if (IS_ERR(bgmac->plat.nicpm_base))
> > >+			return PTR_ERR(bgmac->plat.nicpm_base);
> > >+	}
> > >+
> > > 	bgmac->read = platform_bgmac_read;
> > > 	bgmac->write = platform_bgmac_write;
> > > 	bgmac->idm_read = platform_bgmac_idm_read;
> > >@@ -213,6 +264,7 @@ static int bgmac_remove(struct platform_device *pdev)
> > > static const struct of_device_id bgmac_of_enet_match[] = {
> > > 	{.compatible = "brcm,amac",},
> > > 	{.compatible = "brcm,nsp-amac",},
> > >+	{.compatible = "brcm,ns2-amac",},
> > > 	{},
> > > };
> > >
> > >diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
> > >index 4584958..a805cc8 100644
> > >--- a/drivers/net/ethernet/broadcom/bgmac.c
> > >+++ b/drivers/net/ethernet/broadcom/bgmac.c
> > >@@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
> > > /* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
> > > static void bgmac_chip_init(struct bgmac *bgmac)
> > > {
> > >+	/* Clear any erroneously pending interrupts */
> > >+	bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
> > >+
> > > 	/* 1 interrupt per received frame */
> > > 	bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
> > >
> > >diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
> > >index ea52ac3..b1820ea 100644
> > >--- a/drivers/net/ethernet/broadcom/bgmac.h
> > >+++ b/drivers/net/ethernet/broadcom/bgmac.h
> > >@@ -463,6 +463,7 @@ struct bgmac {
> > > 		struct {
> > > 			void *base;
> > > 			void *idm_base;
> > >+			void *nicpm_base;
> > > 		} plat;
> > > 		struct {
> > > 			struct bcma_device *core;
> > >