* [PATCH 0/2] Support for Axentia TSE-850
@ 2016-11-18 13:48 ` Peter Rosin
0 siblings, 0 replies; 9+ messages in thread
From: Peter Rosin @ 2016-11-18 13:48 UTC (permalink / raw)
To: linux-kernel
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King, devicetree,
linux-arm-kernel
Hi!
After finally having all essintial drivers upstreamed (the
last ones are currently in -next) I would like to have the
dts and the defconfig also upstreamed.
checkpatch complains about missing docs for some compatible
strings:
axentia,tse850v3 (v3 is the hw version that we currently use)
axentia,tse850 (in case we have future versions with commonality)
axentia,linea (the cpu module, reused in other products as well)
nxp,se97b (temp sensor in the below eeprom module)
nxp,24c02 (eeprom on the main board)
st,24c64 (eeprom on the cpu module)
I don't know where I should document those, or if it's even
needed? I get the feeling that the last three are not "my fault".
Anyway, please advice. Or, even better, apply as-is... :-)
Cheers,
Peter
Peter Rosin (2):
ARM: dts: add devicetree for the Axentia TSE-850
ARM: tse850_defconfig: add Axentia TSE-850
MAINTAINERS | 7 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/axentia-linea.dtsi | 52 +++++++
arch/arm/boot/dts/axentia-tse850-3.dts | 275 +++++++++++++++++++++++++++++++++
arch/arm/configs/tse850_defconfig | 223 ++++++++++++++++++++++++++
5 files changed, 558 insertions(+)
create mode 100644 arch/arm/boot/dts/axentia-linea.dtsi
create mode 100644 arch/arm/boot/dts/axentia-tse850-3.dts
create mode 100644 arch/arm/configs/tse850_defconfig
--
2.1.4
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 0/2] Support for Axentia TSE-850
@ 2016-11-18 13:48 ` Peter Rosin
0 siblings, 0 replies; 9+ messages in thread
From: Peter Rosin @ 2016-11-18 13:48 UTC (permalink / raw)
To: linux-kernel
Cc: Mark Rutland, devicetree, Russell King, Rob Herring, Peter Rosin,
linux-arm-kernel
Hi!
After finally having all essintial drivers upstreamed (the
last ones are currently in -next) I would like to have the
dts and the defconfig also upstreamed.
checkpatch complains about missing docs for some compatible
strings:
axentia,tse850v3 (v3 is the hw version that we currently use)
axentia,tse850 (in case we have future versions with commonality)
axentia,linea (the cpu module, reused in other products as well)
nxp,se97b (temp sensor in the below eeprom module)
nxp,24c02 (eeprom on the main board)
st,24c64 (eeprom on the cpu module)
I don't know where I should document those, or if it's even
needed? I get the feeling that the last three are not "my fault".
Anyway, please advice. Or, even better, apply as-is... :-)
Cheers,
Peter
Peter Rosin (2):
ARM: dts: add devicetree for the Axentia TSE-850
ARM: tse850_defconfig: add Axentia TSE-850
MAINTAINERS | 7 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/axentia-linea.dtsi | 52 +++++++
arch/arm/boot/dts/axentia-tse850-3.dts | 275 +++++++++++++++++++++++++++++++++
arch/arm/configs/tse850_defconfig | 223 ++++++++++++++++++++++++++
5 files changed, 558 insertions(+)
create mode 100644 arch/arm/boot/dts/axentia-linea.dtsi
create mode 100644 arch/arm/boot/dts/axentia-tse850-3.dts
create mode 100644 arch/arm/configs/tse850_defconfig
--
2.1.4
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 0/2] Support for Axentia TSE-850
@ 2016-11-18 13:48 ` Peter Rosin
0 siblings, 0 replies; 9+ messages in thread
From: Peter Rosin @ 2016-11-18 13:48 UTC (permalink / raw)
To: linux-arm-kernel
Hi!
After finally having all essintial drivers upstreamed (the
last ones are currently in -next) I would like to have the
dts and the defconfig also upstreamed.
checkpatch complains about missing docs for some compatible
strings:
axentia,tse850v3 (v3 is the hw version that we currently use)
axentia,tse850 (in case we have future versions with commonality)
axentia,linea (the cpu module, reused in other products as well)
nxp,se97b (temp sensor in the below eeprom module)
nxp,24c02 (eeprom on the main board)
st,24c64 (eeprom on the cpu module)
I don't know where I should document those, or if it's even
needed? I get the feeling that the last three are not "my fault".
Anyway, please advice. Or, even better, apply as-is... :-)
Cheers,
Peter
Peter Rosin (2):
ARM: dts: add devicetree for the Axentia TSE-850
ARM: tse850_defconfig: add Axentia TSE-850
MAINTAINERS | 7 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/axentia-linea.dtsi | 52 +++++++
arch/arm/boot/dts/axentia-tse850-3.dts | 275 +++++++++++++++++++++++++++++++++
arch/arm/configs/tse850_defconfig | 223 ++++++++++++++++++++++++++
5 files changed, 558 insertions(+)
create mode 100644 arch/arm/boot/dts/axentia-linea.dtsi
create mode 100644 arch/arm/boot/dts/axentia-tse850-3.dts
create mode 100644 arch/arm/configs/tse850_defconfig
--
2.1.4
^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH 1/2] ARM: dts: add devicetree for the Axentia TSE-850
@ 2016-11-18 13:48 ` Peter Rosin
0 siblings, 0 replies; 9+ messages in thread
From: Peter Rosin @ 2016-11-18 13:48 UTC (permalink / raw)
To: linux-kernel
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King, devicetree,
linux-arm-kernel
Signed-off-by: Peter Rosin <peda@axentia.se>
---
MAINTAINERS | 6 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/axentia-linea.dtsi | 52 +++++++
arch/arm/boot/dts/axentia-tse850-3.dts | 273 +++++++++++++++++++++++++++++++++
4 files changed, 332 insertions(+)
create mode 100644 arch/arm/boot/dts/axentia-linea.dtsi
create mode 100644 arch/arm/boot/dts/axentia-tse850-3.dts
diff --git a/MAINTAINERS b/MAINTAINERS
index 9fe1bc9b414f..7ecf50e5ab47 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2325,6 +2325,12 @@ S: Maintained
F: Documentation/devicetree/bindings/sound/axentia,*
F: sound/soc/atmel/tse850-pcm5142.c
+AXENTIA ARM DEVICES
+M: Peter Rosin <peda@axentia.se>
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S: Maintained
+F: arch/arm/boot/dts/axentia-*
+
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
M: Mauro Carvalho Chehab <mchehab@kernel.org>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index befcd2619902..02cd9b4c55d3 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
+ axentia-tse850-3.dtb \
sama5d31ek.dtb \
sama5d33ek.dtb \
sama5d34ek.dtb \
diff --git a/arch/arm/boot/dts/axentia-linea.dtsi b/arch/arm/boot/dts/axentia-linea.dtsi
new file mode 100644
index 000000000000..07359f9d7419
--- /dev/null
+++ b/arch/arm/boot/dts/axentia-linea.dtsi
@@ -0,0 +1,52 @@
+/*
+ * axentia-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
+ *
+ * Copyright (C) 2016 Axentia Technologies AB
+ * Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "sama5d31.dtsi"
+
+/ {
+ compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+};
+
+&slow_xtal {
+ clock-frequency = <32768>;
+};
+
+&main_xtal {
+ clock-frequency = <12000000>;
+};
+
+&main {
+ clock-frequency = <12000000>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ eeprom@51 {
+ compatible = "st,24c64";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&nand0 {
+ status = "okay";
+
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+};
diff --git a/arch/arm/boot/dts/axentia-tse850-3.dts b/arch/arm/boot/dts/axentia-tse850-3.dts
new file mode 100644
index 000000000000..2052a6f4bb31
--- /dev/null
+++ b/arch/arm/boot/dts/axentia-tse850-3.dts
@@ -0,0 +1,273 @@
+/*
+ * axentia-tse850-3.dts - Device Tree file for the Axentia TSE-850 3.0 board
+ *
+ * Copyright (C) 2016 Axentia Technologies AB
+ * Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "axentia-linea.dtsi"
+
+/ {
+ model = "Axentia TSE-850 3.0";
+ compatible = "axentia,tse850v3", "axentia,tse850", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+ };
+
+ ahb {
+ apb {
+ pinctrl@fffff200 {
+ board {
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+ };
+ };
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+ };
+ };
+
+ sck: oscillator {
+ compatible = "fixed-clock";
+
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
+ clock-output-names = "sck";
+ };
+
+ reg_3v3: regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "3v3-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ana: reg-ana {
+ compatible = "pwm-regulator";
+
+ regulator-name = "ANA";
+
+ pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+ pwm-dutycycle-unit = <1000>;
+ pwm-dutycycle-range = <100 1000>;
+
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <20000000>;
+ regulator-ramp-delay = <1000>;
+ };
+
+ sound {
+ compatible = "axentia,tse850-pcm5142";
+
+ axentia,ssc-controller = <&ssc0>;
+ axentia,audio-codec = <&pcm5142>;
+
+ axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+ axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+ axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+ axentia,ana-supply = <&ana>;
+ };
+
+ dac: dpot-dac {
+ compatible = "dpot-dac";
+ vref-supply = <®_3v3>;
+ io-channels = <&dpot 0>;
+ io-channel-names = "dpot";
+ #io-channel-cells = <1>;
+ };
+
+ envelope-detector {
+ compatible = "axentia,tse850-envelope-detector";
+ io-channels = <&dac 0>;
+ io-channel-names = "dac";
+
+ interrupt-parent = <&pioA>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "comp";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ch1-red {
+ label = "ch-1:red";
+ gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+ };
+ ch1-green {
+ label = "ch-1:green";
+ gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
+ };
+ ch2-red {
+ label = "ch-2:red";
+ gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
+ };
+ ch2-green {
+ label = "ch-2:green";
+ gpios = <&pioA 20 GPIO_ACTIVE_LOW>;
+ };
+ data-red {
+ label = "data:red";
+ gpios = <&pioA 19 GPIO_ACTIVE_LOW>;
+ };
+ data-green {
+ label = "data:green";
+ gpios = <&pioA 18 GPIO_ACTIVE_LOW>;
+ };
+ alarm-red {
+ label = "alarm:red";
+ gpios = <&pioA 17 GPIO_ACTIVE_LOW>;
+ };
+ alarm-green {
+ label = "alarm:green";
+ gpios = <&pioA 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&nand0 {
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ barebox@40000 {
+ label = "bootloader";
+ reg = <0x40000 0x60000>;
+ };
+
+ bareboxenv@c0000 {
+ label = "bareboxenv";
+ reg = <0xc0000 0x40000>;
+ };
+
+ bareboxenv2@100000 {
+ label = "bareboxenv2";
+ reg = <0x100000 0x40000>;
+ };
+
+ oftree@180000 {
+ label = "oftree";
+ reg = <0x180000 0x20000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x500000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+
+ ovlfs@10000000 {
+ label = "ovlfs";
+ reg = <0x10000000 0x10000000>;
+ };
+};
+
+&ssc0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ jc42@18 {
+ compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+ reg = <0x18>;
+ };
+
+ dpot: mcp4651-104@28 {
+ compatible = "microchip,mcp4651-104";
+ reg = <0x28>;
+ #io-channel-cells = <1>;
+ };
+
+ pcm5142: pcm5142@4c {
+ compatible = "ti,pcm5142";
+
+ reg = <0x4c>;
+
+ AVDD-supply = <®_3v3>;
+ DVDD-supply = <®_3v3>;
+ CPVDD-supply = <®_3v3>;
+
+ clocks = <&sck>;
+
+ pll-in = <3>;
+ pll-out = <6>;
+ };
+
+ eeprom@50 {
+ compatible = "nxp,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+&usart0 {
+ status = "okay";
+
+ atmel,use-dma-rx;
+};
+
+&pwm0 {
+ status = "okay";
+
+ pinctrl-0 = <&pinctrl_pwm0_pwml2_1>;
+ pinctrl-names = "default";
+};
+
+&macb1 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@3 {
+ reg = <3>;
+
+ interrupt-parent = <&pioE>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ atmel,vbus-gpio = <&pioC 31 GPIO_ACTIVE_HIGH>;
+};
+
+&usb1 {
+ status = "okay";
+
+ num-ports = <1>;
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ atmel,oc-gpio = <&pioC 15 GPIO_ACTIVE_LOW>;
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 1/2] ARM: dts: add devicetree for the Axentia TSE-850
@ 2016-11-18 13:48 ` Peter Rosin
0 siblings, 0 replies; 9+ messages in thread
From: Peter Rosin @ 2016-11-18 13:48 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Signed-off-by: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
---
MAINTAINERS | 6 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/axentia-linea.dtsi | 52 +++++++
arch/arm/boot/dts/axentia-tse850-3.dts | 273 +++++++++++++++++++++++++++++++++
4 files changed, 332 insertions(+)
create mode 100644 arch/arm/boot/dts/axentia-linea.dtsi
create mode 100644 arch/arm/boot/dts/axentia-tse850-3.dts
diff --git a/MAINTAINERS b/MAINTAINERS
index 9fe1bc9b414f..7ecf50e5ab47 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2325,6 +2325,12 @@ S: Maintained
F: Documentation/devicetree/bindings/sound/axentia,*
F: sound/soc/atmel/tse850-pcm5142.c
+AXENTIA ARM DEVICES
+M: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
+L: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org (moderated for non-subscribers)
+S: Maintained
+F: arch/arm/boot/dts/axentia-*
+
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab-JsYNTwtnfakRB7SZvlqPiA@public.gmane.org>
M: Mauro Carvalho Chehab <mchehab-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index befcd2619902..02cd9b4c55d3 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
+ axentia-tse850-3.dtb \
sama5d31ek.dtb \
sama5d33ek.dtb \
sama5d34ek.dtb \
diff --git a/arch/arm/boot/dts/axentia-linea.dtsi b/arch/arm/boot/dts/axentia-linea.dtsi
new file mode 100644
index 000000000000..07359f9d7419
--- /dev/null
+++ b/arch/arm/boot/dts/axentia-linea.dtsi
@@ -0,0 +1,52 @@
+/*
+ * axentia-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
+ *
+ * Copyright (C) 2016 Axentia Technologies AB
+ * Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "sama5d31.dtsi"
+
+/ {
+ compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+};
+
+&slow_xtal {
+ clock-frequency = <32768>;
+};
+
+&main_xtal {
+ clock-frequency = <12000000>;
+};
+
+&main {
+ clock-frequency = <12000000>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ eeprom@51 {
+ compatible = "st,24c64";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&nand0 {
+ status = "okay";
+
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+};
diff --git a/arch/arm/boot/dts/axentia-tse850-3.dts b/arch/arm/boot/dts/axentia-tse850-3.dts
new file mode 100644
index 000000000000..2052a6f4bb31
--- /dev/null
+++ b/arch/arm/boot/dts/axentia-tse850-3.dts
@@ -0,0 +1,273 @@
+/*
+ * axentia-tse850-3.dts - Device Tree file for the Axentia TSE-850 3.0 board
+ *
+ * Copyright (C) 2016 Axentia Technologies AB
+ * Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "axentia-linea.dtsi"
+
+/ {
+ model = "Axentia TSE-850 3.0";
+ compatible = "axentia,tse850v3", "axentia,tse850", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+ };
+
+ ahb {
+ apb {
+ pinctrl@fffff200 {
+ board {
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+ };
+ };
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+ };
+ };
+
+ sck: oscillator {
+ compatible = "fixed-clock";
+
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
+ clock-output-names = "sck";
+ };
+
+ reg_3v3: regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "3v3-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ana: reg-ana {
+ compatible = "pwm-regulator";
+
+ regulator-name = "ANA";
+
+ pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+ pwm-dutycycle-unit = <1000>;
+ pwm-dutycycle-range = <100 1000>;
+
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <20000000>;
+ regulator-ramp-delay = <1000>;
+ };
+
+ sound {
+ compatible = "axentia,tse850-pcm5142";
+
+ axentia,ssc-controller = <&ssc0>;
+ axentia,audio-codec = <&pcm5142>;
+
+ axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+ axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+ axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+ axentia,ana-supply = <&ana>;
+ };
+
+ dac: dpot-dac {
+ compatible = "dpot-dac";
+ vref-supply = <®_3v3>;
+ io-channels = <&dpot 0>;
+ io-channel-names = "dpot";
+ #io-channel-cells = <1>;
+ };
+
+ envelope-detector {
+ compatible = "axentia,tse850-envelope-detector";
+ io-channels = <&dac 0>;
+ io-channel-names = "dac";
+
+ interrupt-parent = <&pioA>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "comp";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ch1-red {
+ label = "ch-1:red";
+ gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+ };
+ ch1-green {
+ label = "ch-1:green";
+ gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
+ };
+ ch2-red {
+ label = "ch-2:red";
+ gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
+ };
+ ch2-green {
+ label = "ch-2:green";
+ gpios = <&pioA 20 GPIO_ACTIVE_LOW>;
+ };
+ data-red {
+ label = "data:red";
+ gpios = <&pioA 19 GPIO_ACTIVE_LOW>;
+ };
+ data-green {
+ label = "data:green";
+ gpios = <&pioA 18 GPIO_ACTIVE_LOW>;
+ };
+ alarm-red {
+ label = "alarm:red";
+ gpios = <&pioA 17 GPIO_ACTIVE_LOW>;
+ };
+ alarm-green {
+ label = "alarm:green";
+ gpios = <&pioA 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&nand0 {
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ barebox@40000 {
+ label = "bootloader";
+ reg = <0x40000 0x60000>;
+ };
+
+ bareboxenv@c0000 {
+ label = "bareboxenv";
+ reg = <0xc0000 0x40000>;
+ };
+
+ bareboxenv2@100000 {
+ label = "bareboxenv2";
+ reg = <0x100000 0x40000>;
+ };
+
+ oftree@180000 {
+ label = "oftree";
+ reg = <0x180000 0x20000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x500000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+
+ ovlfs@10000000 {
+ label = "ovlfs";
+ reg = <0x10000000 0x10000000>;
+ };
+};
+
+&ssc0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ jc42@18 {
+ compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+ reg = <0x18>;
+ };
+
+ dpot: mcp4651-104@28 {
+ compatible = "microchip,mcp4651-104";
+ reg = <0x28>;
+ #io-channel-cells = <1>;
+ };
+
+ pcm5142: pcm5142@4c {
+ compatible = "ti,pcm5142";
+
+ reg = <0x4c>;
+
+ AVDD-supply = <®_3v3>;
+ DVDD-supply = <®_3v3>;
+ CPVDD-supply = <®_3v3>;
+
+ clocks = <&sck>;
+
+ pll-in = <3>;
+ pll-out = <6>;
+ };
+
+ eeprom@50 {
+ compatible = "nxp,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+&usart0 {
+ status = "okay";
+
+ atmel,use-dma-rx;
+};
+
+&pwm0 {
+ status = "okay";
+
+ pinctrl-0 = <&pinctrl_pwm0_pwml2_1>;
+ pinctrl-names = "default";
+};
+
+&macb1 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@3 {
+ reg = <3>;
+
+ interrupt-parent = <&pioE>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ atmel,vbus-gpio = <&pioC 31 GPIO_ACTIVE_HIGH>;
+};
+
+&usb1 {
+ status = "okay";
+
+ num-ports = <1>;
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ atmel,oc-gpio = <&pioC 15 GPIO_ACTIVE_LOW>;
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+};
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 1/2] ARM: dts: add devicetree for the Axentia TSE-850
@ 2016-11-18 13:48 ` Peter Rosin
0 siblings, 0 replies; 9+ messages in thread
From: Peter Rosin @ 2016-11-18 13:48 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Peter Rosin <peda@axentia.se>
---
MAINTAINERS | 6 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/axentia-linea.dtsi | 52 +++++++
arch/arm/boot/dts/axentia-tse850-3.dts | 273 +++++++++++++++++++++++++++++++++
4 files changed, 332 insertions(+)
create mode 100644 arch/arm/boot/dts/axentia-linea.dtsi
create mode 100644 arch/arm/boot/dts/axentia-tse850-3.dts
diff --git a/MAINTAINERS b/MAINTAINERS
index 9fe1bc9b414f..7ecf50e5ab47 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2325,6 +2325,12 @@ S: Maintained
F: Documentation/devicetree/bindings/sound/axentia,*
F: sound/soc/atmel/tse850-pcm5142.c
+AXENTIA ARM DEVICES
+M: Peter Rosin <peda@axentia.se>
+L: linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
+S: Maintained
+F: arch/arm/boot/dts/axentia-*
+
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
M: Mauro Carvalho Chehab <mchehab@kernel.org>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index befcd2619902..02cd9b4c55d3 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
+ axentia-tse850-3.dtb \
sama5d31ek.dtb \
sama5d33ek.dtb \
sama5d34ek.dtb \
diff --git a/arch/arm/boot/dts/axentia-linea.dtsi b/arch/arm/boot/dts/axentia-linea.dtsi
new file mode 100644
index 000000000000..07359f9d7419
--- /dev/null
+++ b/arch/arm/boot/dts/axentia-linea.dtsi
@@ -0,0 +1,52 @@
+/*
+ * axentia-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
+ *
+ * Copyright (C) 2016 Axentia Technologies AB
+ * Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "sama5d31.dtsi"
+
+/ {
+ compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ memory {
+ reg = <0x20000000 0x20000000>;
+ };
+};
+
+&slow_xtal {
+ clock-frequency = <32768>;
+};
+
+&main_xtal {
+ clock-frequency = <12000000>;
+};
+
+&main {
+ clock-frequency = <12000000>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ eeprom at 51 {
+ compatible = "st,24c64";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&nand0 {
+ status = "okay";
+
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+};
diff --git a/arch/arm/boot/dts/axentia-tse850-3.dts b/arch/arm/boot/dts/axentia-tse850-3.dts
new file mode 100644
index 000000000000..2052a6f4bb31
--- /dev/null
+++ b/arch/arm/boot/dts/axentia-tse850-3.dts
@@ -0,0 +1,273 @@
+/*
+ * axentia-tse850-3.dts - Device Tree file for the Axentia TSE-850 3.0 board
+ *
+ * Copyright (C) 2016 Axentia Technologies AB
+ * Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "axentia-linea.dtsi"
+
+/ {
+ model = "Axentia TSE-850 3.0";
+ compatible = "axentia,tse850v3", "axentia,tse850", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+ };
+
+ ahb {
+ apb {
+ pinctrl at fffff200 {
+ board {
+ pinctrl_usba_vbus: usba_vbus {
+ atmel,pins =
+ <AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+ };
+ };
+ };
+
+ watchdog at fffffe40 {
+ status = "okay";
+ };
+ };
+ };
+
+ sck: oscillator {
+ compatible = "fixed-clock";
+
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
+ clock-output-names = "sck";
+ };
+
+ reg_3v3: regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "3v3-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ana: reg-ana {
+ compatible = "pwm-regulator";
+
+ regulator-name = "ANA";
+
+ pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+ pwm-dutycycle-unit = <1000>;
+ pwm-dutycycle-range = <100 1000>;
+
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <20000000>;
+ regulator-ramp-delay = <1000>;
+ };
+
+ sound {
+ compatible = "axentia,tse850-pcm5142";
+
+ axentia,ssc-controller = <&ssc0>;
+ axentia,audio-codec = <&pcm5142>;
+
+ axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+ axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+ axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+ axentia,ana-supply = <&ana>;
+ };
+
+ dac: dpot-dac {
+ compatible = "dpot-dac";
+ vref-supply = <®_3v3>;
+ io-channels = <&dpot 0>;
+ io-channel-names = "dpot";
+ #io-channel-cells = <1>;
+ };
+
+ envelope-detector {
+ compatible = "axentia,tse850-envelope-detector";
+ io-channels = <&dac 0>;
+ io-channel-names = "dac";
+
+ interrupt-parent = <&pioA>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "comp";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ch1-red {
+ label = "ch-1:red";
+ gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+ };
+ ch1-green {
+ label = "ch-1:green";
+ gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
+ };
+ ch2-red {
+ label = "ch-2:red";
+ gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
+ };
+ ch2-green {
+ label = "ch-2:green";
+ gpios = <&pioA 20 GPIO_ACTIVE_LOW>;
+ };
+ data-red {
+ label = "data:red";
+ gpios = <&pioA 19 GPIO_ACTIVE_LOW>;
+ };
+ data-green {
+ label = "data:green";
+ gpios = <&pioA 18 GPIO_ACTIVE_LOW>;
+ };
+ alarm-red {
+ label = "alarm:red";
+ gpios = <&pioA 17 GPIO_ACTIVE_LOW>;
+ };
+ alarm-green {
+ label = "alarm:green";
+ gpios = <&pioA 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&nand0 {
+ at91bootstrap at 0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ barebox at 40000 {
+ label = "bootloader";
+ reg = <0x40000 0x60000>;
+ };
+
+ bareboxenv at c0000 {
+ label = "bareboxenv";
+ reg = <0xc0000 0x40000>;
+ };
+
+ bareboxenv2 at 100000 {
+ label = "bareboxenv2";
+ reg = <0x100000 0x40000>;
+ };
+
+ oftree at 180000 {
+ label = "oftree";
+ reg = <0x180000 0x20000>;
+ };
+
+ kernel at 200000 {
+ label = "kernel";
+ reg = <0x200000 0x500000>;
+ };
+
+ rootfs at 800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+
+ ovlfs at 10000000 {
+ label = "ovlfs";
+ reg = <0x10000000 0x10000000>;
+ };
+};
+
+&ssc0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ jc42 at 18 {
+ compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+ reg = <0x18>;
+ };
+
+ dpot: mcp4651-104 at 28 {
+ compatible = "microchip,mcp4651-104";
+ reg = <0x28>;
+ #io-channel-cells = <1>;
+ };
+
+ pcm5142: pcm5142 at 4c {
+ compatible = "ti,pcm5142";
+
+ reg = <0x4c>;
+
+ AVDD-supply = <®_3v3>;
+ DVDD-supply = <®_3v3>;
+ CPVDD-supply = <®_3v3>;
+
+ clocks = <&sck>;
+
+ pll-in = <3>;
+ pll-out = <6>;
+ };
+
+ eeprom at 50 {
+ compatible = "nxp,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+&usart0 {
+ status = "okay";
+
+ atmel,use-dma-rx;
+};
+
+&pwm0 {
+ status = "okay";
+
+ pinctrl-0 = <&pinctrl_pwm0_pwml2_1>;
+ pinctrl-names = "default";
+};
+
+&macb1 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy at 3 {
+ reg = <3>;
+
+ interrupt-parent = <&pioE>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ atmel,vbus-gpio = <&pioC 31 GPIO_ACTIVE_HIGH>;
+};
+
+&usb1 {
+ status = "okay";
+
+ num-ports = <1>;
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ atmel,oc-gpio = <&pioC 15 GPIO_ACTIVE_LOW>;
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/2] ARM: tse850_defconfig: add Axentia TSE-850
@ 2016-11-18 13:48 ` Peter Rosin
0 siblings, 0 replies; 9+ messages in thread
From: Peter Rosin @ 2016-11-18 13:48 UTC (permalink / raw)
To: linux-kernel
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King, devicetree,
linux-arm-kernel
Signed-off-by: Peter Rosin <peda@axentia.se>
---
MAINTAINERS | 1 +
arch/arm/boot/dts/axentia-tse850-3.dts | 8 +-
arch/arm/configs/tse850_defconfig | 223 +++++++++++++++++++++++++++++++++
3 files changed, 229 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/configs/tse850_defconfig
diff --git a/MAINTAINERS b/MAINTAINERS
index 7ecf50e5ab47..883d46eb2a06 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2330,6 +2330,7 @@ M: Peter Rosin <peda@axentia.se>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/boot/dts/axentia-*
+F: arch/arm/configs/tse850_defconfig
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
diff --git a/arch/arm/boot/dts/axentia-tse850-3.dts b/arch/arm/boot/dts/axentia-tse850-3.dts
index 2052a6f4bb31..517381f89c3d 100644
--- a/arch/arm/boot/dts/axentia-tse850-3.dts
+++ b/arch/arm/boot/dts/axentia-tse850-3.dts
@@ -22,10 +22,12 @@
ahb {
apb {
pinctrl@fffff200 {
- board {
- pinctrl_usba_vbus: usba_vbus {
+ tse850 {
+ pinctrl_usba_vbus: usba-vbus {
atmel,pins =
- <AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+ <AT91_PIOC 31
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_DEGLITCH>;
};
};
};
diff --git a/arch/arm/configs/tse850_defconfig b/arch/arm/configs/tse850_defconfig
new file mode 100644
index 000000000000..f6076e7e1669
--- /dev/null
+++ b/arch/arm/configs/tse850_defconfig
@@ -0,0 +1,223 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+# CONFIG_FHANDLE is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+# CONFIG_RD_XZ is not set
+# CONFIG_RD_LZO is not set
+# CONFIG_RD_LZ4 is not set
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_SAMA5D3=y
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_AEABI=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_KEXEC=y
+CONFIG_VFP=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=y
+CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=y
+CONFIG_XFRM_USER=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_NET_IPGRE_DEMUX=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_UDP_DIAG=y
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
+CONFIG_NF_CONNTRACK_SNMP=y
+CONFIG_NF_TABLES=y
+CONFIG_NF_TABLES_INET=y
+CONFIG_NF_TABLES_NETDEV=y
+CONFIG_NFT_EXTHDR=y
+CONFIG_NFT_META=y
+CONFIG_NFT_NUMGEN=y
+CONFIG_NFT_CT=y
+CONFIG_NFT_SET_RBTREE=y
+CONFIG_NFT_SET_HASH=y
+CONFIG_NFT_COUNTER=y
+CONFIG_NFT_LOG=y
+CONFIG_NFT_LIMIT=y
+CONFIG_NFT_QUOTA=y
+CONFIG_NFT_REJECT=y
+CONFIG_NFT_HASH=y
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_ARC is not set
+CONFIG_MACB=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_EZCHIP is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_HISILICON is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_RENESAS is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_MICREL_PHY=y
+# CONFIG_USB_NET_DRIVERS is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_LEDS is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_AT91=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_POWER_RESET=y
+CONFIG_SENSORS_JC42=y
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_PWM=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_PCM_OSS=y
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_ARM is not set
+# CONFIG_SND_USB is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_ATMEL_SOC=y
+CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
+# CONFIG_HID_GENERIC is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_REALTEK=y
+CONFIG_USB_STORAGE_DATAFAB=y
+CONFIG_USB_STORAGE_FREECOM=y
+CONFIG_USB_STORAGE_ISD200=y
+CONFIG_USB_STORAGE_USBAT=y
+CONFIG_USB_STORAGE_SDDR09=y
+CONFIG_USB_STORAGE_SDDR55=y
+CONFIG_USB_STORAGE_JUMPSHOT=y
+CONFIG_USB_STORAGE_ALAUDA=y
+CONFIG_USB_STORAGE_ONETOUCH=y
+CONFIG_USB_STORAGE_KARMA=y
+CONFIG_USB_STORAGE_CYPRESS_ATACB=y
+CONFIG_USB_STORAGE_ENE_UB6250=y
+CONFIG_USB_UAS=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_USB_G_SERIAL=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_ENVELOPE_DETECTOR=y
+CONFIG_DPOT_DAC=y
+CONFIG_MCP4531=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_OVERLAY_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_DEBUG_INFO=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_LOCKUP_DETECTOR=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y
+# CONFIG_DETECT_HUNG_TASK is not set
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
+CONFIG_CRYPTO_CCM=y
+CONFIG_CRYPTO_GCM=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA512=y
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_DEV_ATMEL_AES=y
+CONFIG_CRYPTO_DEV_ATMEL_TDES=y
+CONFIG_CRYPTO_DEV_ATMEL_SHA=y
--
2.1.4
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/2] ARM: tse850_defconfig: add Axentia TSE-850
@ 2016-11-18 13:48 ` Peter Rosin
0 siblings, 0 replies; 9+ messages in thread
From: Peter Rosin @ 2016-11-18 13:48 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Signed-off-by: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
---
MAINTAINERS | 1 +
arch/arm/boot/dts/axentia-tse850-3.dts | 8 +-
arch/arm/configs/tse850_defconfig | 223 +++++++++++++++++++++++++++++++++
3 files changed, 229 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/configs/tse850_defconfig
diff --git a/MAINTAINERS b/MAINTAINERS
index 7ecf50e5ab47..883d46eb2a06 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2330,6 +2330,7 @@ M: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
L: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/boot/dts/axentia-*
+F: arch/arm/configs/tse850_defconfig
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab-JsYNTwtnfakRB7SZvlqPiA@public.gmane.org>
diff --git a/arch/arm/boot/dts/axentia-tse850-3.dts b/arch/arm/boot/dts/axentia-tse850-3.dts
index 2052a6f4bb31..517381f89c3d 100644
--- a/arch/arm/boot/dts/axentia-tse850-3.dts
+++ b/arch/arm/boot/dts/axentia-tse850-3.dts
@@ -22,10 +22,12 @@
ahb {
apb {
pinctrl@fffff200 {
- board {
- pinctrl_usba_vbus: usba_vbus {
+ tse850 {
+ pinctrl_usba_vbus: usba-vbus {
atmel,pins =
- <AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+ <AT91_PIOC 31
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_DEGLITCH>;
};
};
};
diff --git a/arch/arm/configs/tse850_defconfig b/arch/arm/configs/tse850_defconfig
new file mode 100644
index 000000000000..f6076e7e1669
--- /dev/null
+++ b/arch/arm/configs/tse850_defconfig
@@ -0,0 +1,223 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+# CONFIG_FHANDLE is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+# CONFIG_RD_XZ is not set
+# CONFIG_RD_LZO is not set
+# CONFIG_RD_LZ4 is not set
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_SAMA5D3=y
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_AEABI=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_KEXEC=y
+CONFIG_VFP=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=y
+CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=y
+CONFIG_XFRM_USER=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_NET_IPGRE_DEMUX=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_UDP_DIAG=y
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
+CONFIG_NF_CONNTRACK_SNMP=y
+CONFIG_NF_TABLES=y
+CONFIG_NF_TABLES_INET=y
+CONFIG_NF_TABLES_NETDEV=y
+CONFIG_NFT_EXTHDR=y
+CONFIG_NFT_META=y
+CONFIG_NFT_NUMGEN=y
+CONFIG_NFT_CT=y
+CONFIG_NFT_SET_RBTREE=y
+CONFIG_NFT_SET_HASH=y
+CONFIG_NFT_COUNTER=y
+CONFIG_NFT_LOG=y
+CONFIG_NFT_LIMIT=y
+CONFIG_NFT_QUOTA=y
+CONFIG_NFT_REJECT=y
+CONFIG_NFT_HASH=y
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_ARC is not set
+CONFIG_MACB=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_EZCHIP is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_HISILICON is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_RENESAS is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_MICREL_PHY=y
+# CONFIG_USB_NET_DRIVERS is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_LEDS is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_AT91=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_POWER_RESET=y
+CONFIG_SENSORS_JC42=y
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_PWM=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_PCM_OSS=y
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_ARM is not set
+# CONFIG_SND_USB is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_ATMEL_SOC=y
+CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
+# CONFIG_HID_GENERIC is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_REALTEK=y
+CONFIG_USB_STORAGE_DATAFAB=y
+CONFIG_USB_STORAGE_FREECOM=y
+CONFIG_USB_STORAGE_ISD200=y
+CONFIG_USB_STORAGE_USBAT=y
+CONFIG_USB_STORAGE_SDDR09=y
+CONFIG_USB_STORAGE_SDDR55=y
+CONFIG_USB_STORAGE_JUMPSHOT=y
+CONFIG_USB_STORAGE_ALAUDA=y
+CONFIG_USB_STORAGE_ONETOUCH=y
+CONFIG_USB_STORAGE_KARMA=y
+CONFIG_USB_STORAGE_CYPRESS_ATACB=y
+CONFIG_USB_STORAGE_ENE_UB6250=y
+CONFIG_USB_UAS=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_USB_G_SERIAL=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_ENVELOPE_DETECTOR=y
+CONFIG_DPOT_DAC=y
+CONFIG_MCP4531=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_OVERLAY_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_DEBUG_INFO=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_LOCKUP_DETECTOR=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y
+# CONFIG_DETECT_HUNG_TASK is not set
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
+CONFIG_CRYPTO_CCM=y
+CONFIG_CRYPTO_GCM=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA512=y
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_DEV_ATMEL_AES=y
+CONFIG_CRYPTO_DEV_ATMEL_TDES=y
+CONFIG_CRYPTO_DEV_ATMEL_SHA=y
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/2] ARM: tse850_defconfig: add Axentia TSE-850
@ 2016-11-18 13:48 ` Peter Rosin
0 siblings, 0 replies; 9+ messages in thread
From: Peter Rosin @ 2016-11-18 13:48 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Peter Rosin <peda@axentia.se>
---
MAINTAINERS | 1 +
arch/arm/boot/dts/axentia-tse850-3.dts | 8 +-
arch/arm/configs/tse850_defconfig | 223 +++++++++++++++++++++++++++++++++
3 files changed, 229 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/configs/tse850_defconfig
diff --git a/MAINTAINERS b/MAINTAINERS
index 7ecf50e5ab47..883d46eb2a06 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2330,6 +2330,7 @@ M: Peter Rosin <peda@axentia.se>
L: linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/boot/dts/axentia-*
+F: arch/arm/configs/tse850_defconfig
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
diff --git a/arch/arm/boot/dts/axentia-tse850-3.dts b/arch/arm/boot/dts/axentia-tse850-3.dts
index 2052a6f4bb31..517381f89c3d 100644
--- a/arch/arm/boot/dts/axentia-tse850-3.dts
+++ b/arch/arm/boot/dts/axentia-tse850-3.dts
@@ -22,10 +22,12 @@
ahb {
apb {
pinctrl at fffff200 {
- board {
- pinctrl_usba_vbus: usba_vbus {
+ tse850 {
+ pinctrl_usba_vbus: usba-vbus {
atmel,pins =
- <AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+ <AT91_PIOC 31
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_DEGLITCH>;
};
};
};
diff --git a/arch/arm/configs/tse850_defconfig b/arch/arm/configs/tse850_defconfig
new file mode 100644
index 000000000000..f6076e7e1669
--- /dev/null
+++ b/arch/arm/configs/tse850_defconfig
@@ -0,0 +1,223 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_SYSVIPC=y
+# CONFIG_FHANDLE is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+# CONFIG_RD_XZ is not set
+# CONFIG_RD_LZO is not set
+# CONFIG_RD_LZ4 is not set
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+# CONFIG_LBDAF is not set
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_AT91=y
+CONFIG_SOC_SAMA5D3=y
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_AEABI=y
+CONFIG_UACCESS_WITH_MEMCPY=y
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw"
+CONFIG_KEXEC=y
+CONFIG_VFP=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=y
+CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=y
+CONFIG_XFRM_USER=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_NET_IPGRE_DEMUX=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_UDP_DIAG=y
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=y
+# CONFIG_NF_CONNTRACK_PROCFS is not set
+CONFIG_NF_CONNTRACK_SNMP=y
+CONFIG_NF_TABLES=y
+CONFIG_NF_TABLES_INET=y
+CONFIG_NF_TABLES_NETDEV=y
+CONFIG_NFT_EXTHDR=y
+CONFIG_NFT_META=y
+CONFIG_NFT_NUMGEN=y
+CONFIG_NFT_CT=y
+CONFIG_NFT_SET_RBTREE=y
+CONFIG_NFT_SET_HASH=y
+CONFIG_NFT_COUNTER=y
+CONFIG_NFT_LOG=y
+CONFIG_NFT_LIMIT=y
+CONFIG_NFT_QUOTA=y
+CONFIG_NFT_REJECT=y
+CONFIG_NFT_HASH=y
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=4
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_ATMEL_TCLIB=y
+CONFIG_ATMEL_SSC=y
+CONFIG_EEPROM_AT24=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_ARC is not set
+CONFIG_MACB=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_EZCHIP is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_HISILICON is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_RENESAS is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_MICREL_PHY=y
+# CONFIG_USB_NET_DRIVERS is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_LEDS is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_ATMEL=y
+CONFIG_SERIAL_ATMEL_CONSOLE=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_AT91=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_POWER_RESET=y
+CONFIG_SENSORS_JC42=y
+CONFIG_WATCHDOG=y
+CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_PWM=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_PCM_OSS=y
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_ARM is not set
+# CONFIG_SND_USB is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_ATMEL_SOC=y
+CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
+# CONFIG_HID_GENERIC is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_REALTEK=y
+CONFIG_USB_STORAGE_DATAFAB=y
+CONFIG_USB_STORAGE_FREECOM=y
+CONFIG_USB_STORAGE_ISD200=y
+CONFIG_USB_STORAGE_USBAT=y
+CONFIG_USB_STORAGE_SDDR09=y
+CONFIG_USB_STORAGE_SDDR55=y
+CONFIG_USB_STORAGE_JUMPSHOT=y
+CONFIG_USB_STORAGE_ALAUDA=y
+CONFIG_USB_STORAGE_ONETOUCH=y
+CONFIG_USB_STORAGE_KARMA=y
+CONFIG_USB_STORAGE_CYPRESS_ATACB=y
+CONFIG_USB_STORAGE_ENE_UB6250=y
+CONFIG_USB_UAS=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_ATMEL_USBA=y
+CONFIG_USB_G_SERIAL=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AT91RM9200=y
+CONFIG_DMADEVICES=y
+CONFIG_AT_HDMAC=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_AT91_ADC=y
+CONFIG_ENVELOPE_DETECTOR=y
+CONFIG_DPOT_DAC=y
+CONFIG_MCP4531=y
+CONFIG_PWM=y
+CONFIG_PWM_ATMEL=y
+CONFIG_PWM_ATMEL_TCB=y
+CONFIG_EXT4_FS=y
+CONFIG_FANOTIFY=y
+CONFIG_OVERLAY_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_DEBUG_INFO=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_LOCKUP_DETECTOR=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y
+# CONFIG_DETECT_HUNG_TASK is not set
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
+CONFIG_CRYPTO_CCM=y
+CONFIG_CRYPTO_GCM=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA512=y
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_DEV_ATMEL_AES=y
+CONFIG_CRYPTO_DEV_ATMEL_TDES=y
+CONFIG_CRYPTO_DEV_ATMEL_SHA=y
--
2.1.4
^ permalink raw reply related [flat|nested] 9+ messages in thread
end of thread, other threads:[~2016-11-18 18:18 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-11-18 13:48 [PATCH 0/2] Support for Axentia TSE-850 Peter Rosin
2016-11-18 13:48 ` Peter Rosin
2016-11-18 13:48 ` Peter Rosin
2016-11-18 13:48 ` [PATCH 1/2] ARM: dts: add devicetree for the " Peter Rosin
2016-11-18 13:48 ` Peter Rosin
2016-11-18 13:48 ` Peter Rosin
2016-11-18 13:48 ` [PATCH 2/2] ARM: tse850_defconfig: add " Peter Rosin
2016-11-18 13:48 ` Peter Rosin
2016-11-18 13:48 ` Peter Rosin
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.