[PATCH v2 2/4] phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips

[Vivek Gautam <vivek.gautam@codeaurora.org>]

PHY transceiver driver for QUSB2 phy controller that provides
HighSpeed functionality for DWC3 controller present on
Qualcomm chipsets.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
---

Changes since v1:
 - removed reference to clk_enabled/pwr_enabled.
 - moved clock and regulator enable code to phy_power_on/off() callbacks.
 - fixed return on EPROBE_DEFER in qusb2_phy_probe().
 - fixed phy create and phy register ordering.
 - removed references to non-lkml links from commit message.
 - took care of other minor nits.
 - Fixed coccinelle warnings -
   'PTR_ERR applied after initialization to constant'
 - Addressed review comment, regarding qfprom access for tune2 param value.
   This driver is now based on qfprom patch[1] that allows byte access now.

Comments not addressed in this version:
 -- Have not addressed Kishon's comment to move phy init table stuff
    to generic phy calibration bindings.

[1] https://lkml.org/lkml/2016/11/17/21

 drivers/phy/Kconfig          |  11 +
 drivers/phy/Makefile         |   1 +
 drivers/phy/phy-qcom-qusb2.c | 549 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 561 insertions(+)
 create mode 100644 drivers/phy/phy-qcom-qusb2.c

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index e8eb7f2..f1dcec1 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -430,6 +430,17 @@ config PHY_STIH407_USB
 	  Enable this support to enable the picoPHY device used by USB2
 	  and USB3 controllers on STMicroelectronics STiH407 SoC families.
 
+config PHY_QCOM_QUSB2
+	tristate "Qualcomm QUSB2 PHY Driver"
+	depends on OF && (ARCH_QCOM || COMPILE_TEST)
+	select GENERIC_PHY
+	select RESET_CONTROLLER
+	help
+	  Enable this to support the HighSpeed QUSB2 PHY transceiver for USB
+	  controllers on Qualcomm chips. This driver supports the high-speed
+	  PHY which is usually paired with either the ChipIdea or Synopsys DWC3
+	  USB IPs on MSM SOCs.
+
 config PHY_QCOM_UFS
 	tristate "Qualcomm UFS PHY driver"
 	depends on OF && ARCH_QCOM
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 65eb2f4..dad1682 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -49,6 +49,7 @@ obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
 obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
 obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
 obj-$(CONFIG_PHY_STIH407_USB)		+= phy-stih407-usb.o
+obj-$(CONFIG_PHY_QCOM_QUSB2) 	+= phy-qcom-qusb2.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-20nm.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-14nm.o
diff --git a/drivers/phy/phy-qcom-qusb2.c b/drivers/phy/phy-qcom-qusb2.c
new file mode 100644
index 0000000..d3f9657
--- /dev/null
+++ b/drivers/phy/phy-qcom-qusb2.c
@@ -0,0 +1,549 @@
+/*
+ * Copyright (c) 2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mfd/syscon.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#define QUSB2PHY_PLL_TEST		0x04
+#define CLK_REF_SEL			BIT(7)
+
+#define QUSB2PHY_PLL_TUNE		0x08
+#define QUSB2PHY_PLL_USER_CTL1		0x0c
+#define QUSB2PHY_PLL_USER_CTL2		0x10
+#define QUSB2PHY_PLL_AUTOPGM_CTL1	0x1c
+#define QUSB2PHY_PLL_PWR_CTRL		0x18
+
+#define QUSB2PHY_PLL_STATUS		0x38
+#define PLL_LOCKED			BIT(5)
+
+#define QUSB2PHY_PORT_TUNE1             0x80
+#define QUSB2PHY_PORT_TUNE2             0x84
+#define QUSB2PHY_PORT_TUNE3             0x88
+#define QUSB2PHY_PORT_TUNE4             0x8C
+#define QUSB2PHY_PORT_TUNE5		0x90
+#define QUSB2PHY_PORT_TEST2		0x9c
+
+#define QUSB2PHY_PORT_POWERDOWN		0xB4
+#define CLAMP_N_EN			BIT(5)
+#define FREEZIO_N			BIT(1)
+#define POWER_DOWN			BIT(0)
+
+#define QUSB2PHY_REFCLK_ENABLE		BIT(0)
+
+#define PHY_CLK_SCHEME_SEL		BIT(0)
+
+struct qusb2_phy_init_tbl {
+	unsigned int reg_offset;
+	unsigned int cfg_val;
+};
+#define QCOM_QUSB2_PHY_INIT_CFG(reg, val) \
+	{				\
+		.reg_offset = reg,	\
+		.cfg_val = val,		\
+	}
+
+static struct qusb2_phy_init_tbl msm8996_phy_init_tbl[] = {
+	QCOM_QUSB2_PHY_INIT_CFG(QUSB2PHY_PORT_TUNE1, 0xF8),
+	QCOM_QUSB2_PHY_INIT_CFG(QUSB2PHY_PORT_TUNE2, 0xB3),
+	QCOM_QUSB2_PHY_INIT_CFG(QUSB2PHY_PORT_TUNE3, 0x83),
+	QCOM_QUSB2_PHY_INIT_CFG(QUSB2PHY_PORT_TUNE4, 0xC0),
+	QCOM_QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TUNE, 0x30),
+	QCOM_QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL1, 0x79),
+	QCOM_QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL2, 0x21),
+	QCOM_QUSB2_PHY_INIT_CFG(QUSB2PHY_PORT_TEST2, 0x14),
+	QCOM_QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_AUTOPGM_CTL1, 0x9F),
+	QCOM_QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00),
+};
+
+struct qusb2_phy_init_cfg {
+	struct qusb2_phy_init_tbl *phy_init_tbl;
+	int phy_init_tbl_sz;
+	/* offset to PHY_CLK_SCHEME register in TCSR map. */
+	unsigned int clk_scheme_offset;
+};
+
+const struct qusb2_phy_init_cfg msm8996_phy_init_cfg = {
+	.phy_init_tbl = msm8996_phy_init_tbl,
+	.phy_init_tbl_sz = ARRAY_SIZE(msm8996_phy_init_tbl),
+};
+
+/**
+ * struct qusb2_phy: Structure holding qusb2 phy attributes.
+ *
+ * @phy: pointer to generic phy.
+ * @base: pointer to iomapped memory space for qubs2 phy.
+ *
+ * @cfg_ahb_clk: pointer to AHB2PHY interface clock.
+ * @ref_clk: pointer to reference clock.
+ * @ref_clk_src: pointer to source to reference clock.
+ * @iface_src: pointer to phy interface clock.
+ *
+ * @phy_reset: Pointer to phy reset control
+ *
+ * @vdda_phy: vdd supply to the phy core block.
+ * @vdda_pll: 1.8V vdd supply to ref_clk block.
+ * @vdda_phy_dpdm: 3.1V vdd supply to Dp/Dm port signals.
+ * @tcsr: pointer to TCSR syscon register map.
+ *
+ * @cfg: phy initialization config data
+ * @has_se_clk_scheme: indicate if PHY has Single-ended ref clock scheme
+ */
+struct qusb2_phy {
+	struct phy *phy;
+	void __iomem *base;
+
+	struct clk *cfg_ahb_clk;
+	struct clk *ref_clk;
+	struct clk *ref_clk_src;
+	struct clk *iface_clk;
+
+	struct reset_control *phy_reset;
+
+	struct regulator *vdd_phy;
+	struct regulator *vdda_pll;
+	struct regulator *vdda_phy_dpdm;
+
+	struct regmap *tcsr;
+
+	const struct qusb2_phy_init_cfg *cfg;
+	bool has_se_clk_scheme;
+};
+
+static inline void qusb2_setbits(void __iomem *reg, u32 val)
+{
+	u32 reg_val;
+
+	reg_val = readl_relaxed(reg);
+	reg_val |= val;
+	writel_relaxed(reg_val, reg);
+
+	/* Ensure above write is completed */
+	mb();
+}
+
+static inline void qusb2_clrbits(void __iomem *reg, u32 val)
+{
+	u32 reg_val;
+
+	reg_val = readl_relaxed(reg);
+	reg_val &= ~val;
+	writel_relaxed(reg_val, reg);
+
+	/* Ensure above write is completed */
+	mb();
+}
+
+static void qcom_qusb2_phy_configure(void __iomem *base,
+				struct qusb2_phy_init_tbl init_tbl[],
+				int init_tbl_sz)
+{
+	int i;
+
+	for (i = 0; i < init_tbl_sz; i++) {
+		writel_relaxed(init_tbl[i].cfg_val,
+				base + init_tbl[i].reg_offset);
+	}
+
+	/* flush buffered writes */
+	mb();
+}
+
+static void qusb2_phy_enable_clocks(struct qusb2_phy *qphy, bool on)
+{
+	if (on) {
+		clk_prepare_enable(qphy->iface_clk);
+		clk_prepare_enable(qphy->ref_clk_src);
+	} else {
+		clk_disable_unprepare(qphy->ref_clk_src);
+		clk_disable_unprepare(qphy->iface_clk);
+	}
+
+	dev_vdbg(&qphy->phy->dev, "%s(): clocks enabled\n", __func__);
+}
+
+static int qusb2_phy_enable_power(struct qusb2_phy *qphy, bool on)
+{
+	int ret;
+	struct device *dev = &qphy->phy->dev;
+
+	if (!on)
+		goto disable_vdda_phy_dpdm;
+
+	ret = regulator_enable(qphy->vdd_phy);
+	if (ret) {
+		dev_err(dev, "Unable to enable vdd-phy:%d\n", ret);
+		goto err_vdd_phy;
+	}
+
+	ret = regulator_enable(qphy->vdda_pll);
+	if (ret) {
+		dev_err(dev, "Unable to enable vdda-pll:%d\n", ret);
+		goto disable_vdd_phy;
+	}
+
+	ret = regulator_enable(qphy->vdda_phy_dpdm);
+	if (ret) {
+		dev_err(dev, "Unable to enable vdda-phy-dpdm:%d\n", ret);
+		goto disable_vdda_pll;
+	}
+
+	dev_vdbg(dev, "%s() regulators are turned on.\n", __func__);
+
+	return ret;
+
+disable_vdda_phy_dpdm:
+	regulator_disable(qphy->vdda_phy_dpdm);
+disable_vdda_pll:
+	regulator_disable(qphy->vdda_pll);
+disable_vdd_phy:
+	regulator_disable(qphy->vdd_phy);
+err_vdd_phy:
+	dev_vdbg(dev, "%s() regulators are turned off.\n", __func__);
+	return ret;
+}
+
+/*
+ * Fetches HS Tx tuning value from e-fuse and sets QUSB2PHY_PORT_TUNE2
+ * register.
+ * For any error case, skip setting the value and use the default value.
+ */
+static int qusb2_phy_set_tune2_param(struct qusb2_phy *qphy)
+{
+	struct device *dev = &qphy->phy->dev;
+	struct nvmem_cell *cell;
+	ssize_t len;
+	u8 *val;
+
+	/*
+	 * Read EFUSE register having TUNE2 parameter's high nibble.
+	 * If efuse register shows value as 0x0, or if we fail to find
+	 * a valid efuse register settings, then use default value
+	 * as 0xB for high nibble that we have already set while
+	 * configuring phy.
+	 */
+	cell = devm_nvmem_cell_get(dev, "tune2_hstx_trim_efuse");
+	if (IS_ERR(cell)) {
+		if (PTR_ERR(cell) == -EPROBE_DEFER)
+			return PTR_ERR(cell);
+		goto skip;
+	}
+
+	/*
+	 * we need to read only one byte here, since the required
+	 * parameter value fits in one nibble
+	 */
+	val = (u8 *)nvmem_cell_read(cell, &len);
+	if (!IS_ERR(val)) {
+		/* Fused TUNE2 value is the higher nibble only */
+		qusb2_setbits(qphy->base + QUSB2PHY_PORT_TUNE2,
+							val[0] << 0x4);
+	} else {
+		dev_dbg(dev, "failed reading hs-tx trim value: %ld\n",
+							PTR_ERR(val));
+	}
+
+skip:
+	return 0;
+}
+
+static int qusb2_phy_poweron(struct phy *phy)
+{
+	struct qusb2_phy *qphy = phy_get_drvdata(phy);
+	int ret;
+
+	dev_vdbg(&phy->dev, "Powering-on QUSB2 phy\n");
+
+	ret = qusb2_phy_enable_power(qphy, true);
+	if (ret)
+		return ret;
+
+	qusb2_phy_enable_clocks(qphy, true);
+
+	return ret;
+}
+
+static int qusb2_phy_poweroff(struct phy *phy)
+{
+	struct qusb2_phy *qphy = phy_get_drvdata(phy);
+
+	qusb2_phy_enable_clocks(qphy, false);
+	qusb2_phy_enable_power(qphy, false);
+
+	return 0;
+}
+
+static int qusb2_phy_init(struct phy *phy)
+{
+	struct qusb2_phy *qphy = phy_get_drvdata(phy);
+	unsigned int reset_val;
+	unsigned int clk_scheme;
+	int ret;
+
+	dev_vdbg(&phy->dev, "Initializing QUSB2 phy\n");
+
+	/* enable ahb interface clock to program phy */
+	clk_prepare_enable(qphy->cfg_ahb_clk);
+
+	/* Perform phy reset */
+	ret = reset_control_assert(qphy->phy_reset);
+	if (ret) {
+		dev_err(&phy->dev, "Failed to assert phy_reset\n");
+		return ret;
+	}
+	/* 100 us delay to keep PHY in reset mode */
+	usleep_range(100, 150);
+	ret = reset_control_deassert(qphy->phy_reset);
+	if (ret) {
+		dev_err(&phy->dev, "Failed to de-assert phy_reset\n");
+		return ret;
+	}
+
+	/* Disable the PHY */
+	qusb2_setbits(qphy->base + QUSB2PHY_PORT_POWERDOWN,
+			CLAMP_N_EN | FREEZIO_N | POWER_DOWN);
+
+	/* save reset value to override based on clk scheme */
+	reset_val = readl_relaxed(qphy->base + QUSB2PHY_PLL_TEST);
+
+	qcom_qusb2_phy_configure(qphy->base, qphy->cfg->phy_init_tbl,
+				qphy->cfg->phy_init_tbl_sz);
+
+	/* Check for efuse value for tuning the PHY */
+	ret = qusb2_phy_set_tune2_param(qphy);
+	if (ret)
+		return ret;
+
+	/* Enable the PHY */
+	qusb2_clrbits(qphy->base + QUSB2PHY_PORT_POWERDOWN, POWER_DOWN);
+
+	/* Require to get phy pll lock successfully */
+	usleep_range(150, 160);
+
+	/* Default is Single-ended clock on msm8996 */
+	qphy->has_se_clk_scheme = true;
+	/*
+	 * read TCSR_PHY_CLK_SCHEME register to check if Single-ended
+	 * clock scheme is selected. If yes, then disable differential
+	 * ref_clk and use single-ended clock, otherwise use differential
+	 * ref_clk only.
+	 */
+	if (qphy->tcsr) {
+		ret = regmap_read(qphy->tcsr, qphy->cfg->clk_scheme_offset,
+							&clk_scheme);
+		/* is it a differential clock scheme ? */
+		if (!(clk_scheme & PHY_CLK_SCHEME_SEL)) {
+			dev_vdbg(&phy->dev, "%s: select differential clk src\n",
+								__func__);
+			qphy->has_se_clk_scheme = false;
+		} else {
+			dev_vdbg(&phy->dev, "%s: select single-ended clk src\n",
+								__func__);
+		}
+	}
+
+	if (!qphy->has_se_clk_scheme) {
+		reset_val &= ~CLK_REF_SEL;
+		clk_prepare_enable(qphy->ref_clk);
+	} else {
+		reset_val |= CLK_REF_SEL;
+	}
+
+	writel_relaxed(reset_val, qphy->base + QUSB2PHY_PLL_TEST);
+
+	/* Make sure that above write is completed to get PLL source clock */
+	wmb();
+
+	/* Required to get PHY PLL lock successfully */
+	usleep_range(100, 110);
+
+	if (!(readb_relaxed(qphy->base + QUSB2PHY_PLL_STATUS) &
+					PLL_LOCKED)) {
+		dev_err(&phy->dev, "QUSB PHY PLL LOCK fails:%x\n",
+			readb_relaxed(qphy->base + QUSB2PHY_PLL_STATUS));
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+static int qusb2_phy_exit(struct phy *phy)
+{
+	struct qusb2_phy *qphy = phy_get_drvdata(phy);
+
+	/* Disable the PHY */
+	qusb2_setbits(qphy->base + QUSB2PHY_PORT_POWERDOWN,
+			CLAMP_N_EN | FREEZIO_N | POWER_DOWN);
+
+	if (!qphy->has_se_clk_scheme)
+		clk_disable_unprepare(qphy->ref_clk);
+
+	clk_disable_unprepare(qphy->cfg_ahb_clk);
+
+	return 0;
+}
+
+static const struct phy_ops qusb2_phy_gen_ops = {
+	.init		= qusb2_phy_init,
+	.exit		= qusb2_phy_exit,
+	.power_on	= qusb2_phy_poweron,
+	.power_off	= qusb2_phy_poweroff,
+	.owner		= THIS_MODULE,
+};
+
+static const struct of_device_id qusb2_phy_of_match_table[] = {
+	{
+		.compatible	= "qcom,msm8996-qusb2-phy",
+		.data		= &msm8996_phy_init_cfg,
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, qusb2_phy_of_match_table);
+
+static int qusb2_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct qusb2_phy *qphy;
+	struct phy_provider *phy_provider;
+	struct phy *generic_phy;
+	const struct of_device_id *match;
+	struct resource *res;
+	int ret;
+
+	qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
+	if (!qphy)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	qphy->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(qphy->base))
+		return PTR_ERR(qphy->base);
+
+	qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb_clk");
+	if (IS_ERR(qphy->cfg_ahb_clk)) {
+		ret = PTR_ERR(qphy->cfg_ahb_clk);
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "failed to get cfg_ahb_clk\n");
+		return ret;
+	}
+
+	qphy->ref_clk_src = devm_clk_get(dev, "ref_clk_src");
+	if (IS_ERR(qphy->ref_clk_src)) {
+		ret = PTR_ERR(qphy->ref_clk_src);
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "clk get failed for ref_clk_src\n");
+		return ret;
+	}
+
+	qphy->ref_clk = devm_clk_get(dev, "ref_clk");
+	if (IS_ERR(qphy->ref_clk)) {
+		ret = PTR_ERR(qphy->ref_clk);
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "clk get failed for ref_clk\n");
+		return ret;
+	} else {
+		clk_set_rate(qphy->ref_clk, 19200000);
+	}
+
+	qphy->iface_clk = devm_clk_get(dev, "iface_clk");
+	if (IS_ERR(qphy->iface_clk)) {
+		ret = PTR_ERR(qphy->iface_clk);
+		if (ret != -EPROBE_DEFER) {
+			qphy->iface_clk = NULL;
+			dev_dbg(dev, "clk get failed for iface_clk\n");
+		} else {
+			return ret;
+		}
+	}
+
+	qphy->phy_reset = devm_reset_control_get(&pdev->dev, "phy");
+	if (IS_ERR(qphy->phy_reset)) {
+		dev_err(dev, "failed to get phy core reset\n");
+		return PTR_ERR(qphy->phy_reset);
+	}
+
+	qphy->vdd_phy = devm_regulator_get(dev, "vdd-phy");
+	if (IS_ERR(qphy->vdd_phy)) {
+		dev_err(dev, "unable to get vdd-phy supply\n");
+		return PTR_ERR(qphy->vdd_phy);
+	}
+
+	qphy->vdda_pll = devm_regulator_get(dev, "vdda-pll");
+	if (IS_ERR(qphy->vdda_pll)) {
+		dev_err(dev, "unable to get vdda-pll supply\n");
+		return PTR_ERR(qphy->vdda_pll);
+	}
+
+	qphy->vdda_phy_dpdm = devm_regulator_get(dev, "vdda-phy-dpdm");
+	if (IS_ERR(qphy->vdda_phy_dpdm)) {
+		dev_err(dev, "unable to get vdda-phy-dpdm supply\n");
+		return PTR_ERR(qphy->vdda_phy_dpdm);
+	}
+
+	/* Get the specific init parameters of QMP phy */
+	match = of_match_node(qusb2_phy_of_match_table, dev->of_node);
+	qphy->cfg = match->data;
+
+	qphy->tcsr = syscon_regmap_lookup_by_phandle(dev->of_node,
+							"qcom,tcsr-syscon");
+	if (IS_ERR(qphy->tcsr)) {
+		dev_dbg(dev, "Failed to lookup TCSR regmap\n");
+		qphy->tcsr = NULL;
+	}
+
+	generic_phy = devm_phy_create(dev, NULL, &qusb2_phy_gen_ops);
+	if (IS_ERR(generic_phy)) {
+		ret = PTR_ERR(generic_phy);
+		dev_err(dev, "%s: failed to create phy %d\n", __func__, ret);
+		return ret;
+	}
+	qphy->phy = generic_phy;
+
+	dev_set_drvdata(dev, qphy);
+	phy_set_drvdata(generic_phy, qphy);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider)) {
+		ret = PTR_ERR(phy_provider);
+		dev_err(dev, "%s: failed to register phy %d\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static struct platform_driver qusb2_phy_driver = {
+	.probe		= qusb2_phy_probe,
+	.driver = {
+		.name	= "qcom-qusb2-phy",
+		.of_match_table = of_match_ptr(qusb2_phy_of_match_table),
+	},
+};
+
+module_platform_driver(qusb2_phy_driver);
+
+MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>");
+MODULE_DESCRIPTION("Qualcomm QUSB2 PHY driver");
+MODULE_LICENSE("GPL v2");
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project