[PATCH 0/3][v3] Add QorIQ LS2088A platform support

[PATCH 0/3][v3] Add QorIQ LS2088A platform support

[Abhimanyu Saini]

This patchset adds support for the QorIQ LS2088A SoC.
LS2088A SoC is similar to LS2080A SoC with a few differences like it has A72 cores.

This patchset
        - reorganize LS2088A DTS/DTSI for code reuseability
        - adds LS2088A device dtsi and dts files.

Abhimanyu Saini (3):
  dt-bindings: Add compatible for LS2088A QDS and RDB boards
  arm64: freescale: ls2080a: Split devicetree for code resuability
  arm64: Add DTS support for FSL's LS2088A SoC

Changes for v3:
	- rename dts/dtsi files
Changes for v2:
	- reorganize LS2088A device tree to use common
	  nodes from LS2080A device trees.
	- Both LS2080A and LS2088A have same hardware
	  controllers, so separate dt-binding patches for
	  pcie, gpio, dspi, qspi are not required.

Abhimanyu Saini (3):
  dt-bindings: Add compatible for LS2088A QDS and RDB board
  arm64: freescale: ls2080a: Split devicetree for code resuability
  arm64: freescale: ls2088a: Add DTS support for FSL's LS2088A SoC

 Documentation/devicetree/bindings/arm/fsl.txt     |  11 +
 arch/arm64/boot/dts/freescale/Makefile            |   2 +
 arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts | 154 +----
 arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts | 106 +---
 arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi    | 715 +---------------------
 arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts |  65 ++
 arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts |  65 ++
 arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi    | 162 +++++
 8 files changed, 331 insertions(+), 949 deletions(-)
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi

-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/3][v3] dt-bindings: Add compatible for LS2088A QDS and RDB board

[Abhimanyu Saini]

Signed-off-by: Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
Signed-off-by: Priyanka Jain <priyanka.jain-3arQi8VN3Tc@public.gmane.org>
Signed-off-by: Ashish Kumar <ashish.kumar-3arQi8VN3Tc@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
Changes for v2:
	- reorganize LS2088A device tree to use common
	  nodes from LS2080A device trees.
	- Both LS2080A and LS2088A have same hardware
	  controllers, so separate dt-binding patches for
	  pcie, gpio, dspi, qspi are not required.

 Documentation/devicetree/bindings/arm/fsl.txt | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index d6ee9c6..75ad8c5 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -179,3 +179,14 @@ LS2080A ARMv8 based RDB Board
 Required root node properties:
     - compatible = "fsl,ls2080a-rdb", "fsl,ls2080a";
 
+LS2088A SoC
+Required root node properties:
+    - compatible = "fsl,ls2088a";
+
+LS2088A ARMv8 based QDS Board
+Required root node properties:
+    - compatible = "fsl,ls2088a-qds", "fsl,ls2088a";
+
+LS2088A ARMv8 based RDB Board
+Required root node properties:
+    - compatible = "fsl,ls2088a-rdb", "fsl,ls2088a";
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/3][v3] arm64: freescale: ls2080a: Split devicetree for code resuability

[Abhimanyu Saini]

LS2088A and LS2080A are similar SoCs with a few differences like
ARM cores etc.

Reorganize the LS2080A device tree to move the common nodes to:
        - fsl-ls208xa.dtsi
        - fsl-ls208xa-rdb.dtsi
        - fsl-ls208xa-qds.dtsi

Signed-off-by: Priyanka Jain <priyanka.jain-3arQi8VN3Tc@public.gmane.org>
Signed-off-by: Ashish Kumar <ashish.kumar-3arQi8VN3Tc@public.gmane.org>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
---
Changes for v3:
        - rename dts/dtsi files

 arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts | 154 +----
 arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts | 106 +---
 arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi    | 715 +---------------------
 3 files changed, 26 insertions(+), 949 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
index 8bc1f8f..3cf4a5c 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
@@ -1,8 +1,9 @@
 /*
  * Device Tree file for Freescale LS2080a QDS Board.
  *
- * Copyright (C) 2015, Freescale Semiconductor
+ * Copyright (C) 2015-17, Freescale Semiconductor
  *
+ * Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
  * Bhupesh Sharma <bhupesh.sharma-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
  *
  * This file is dual-licensed: you can use it either under the terms
@@ -62,153 +63,4 @@
 	};
 };
 
-&esdhc {
-	status = "okay";
-};
-
-&ifc {
-	status = "okay";
-	#address-cells = <2>;
-	#size-cells = <1>;
-	ranges = <0x0 0x0 0x5 0x80000000 0x08000000
-		  0x2 0x0 0x5 0x30000000 0x00010000
-		  0x3 0x0 0x5 0x20000000 0x00010000>;
-
-	nor@0,0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "cfi-flash";
-		reg = <0x0 0x0 0x8000000>;
-		bank-width = <2>;
-		device-width = <1>;
-	};
-
-	nand@2,0 {
-	     compatible = "fsl,ifc-nand";
-	     reg = <0x2 0x0 0x10000>;
-	};
-
-	cpld@3,0 {
-	     reg = <0x3 0x0 0x10000>;
-	     compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis";
-	};
-};
-
-&i2c0 {
-	status = "okay";
-	pca9547@77 {
-		compatible = "nxp,pca9547";
-		reg = <0x77>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x00>;
-			rtc@68 {
-				compatible = "dallas,ds3232";
-				reg = <0x68>;
-			};
-		};
-
-		i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x02>;
-
-			ina220@40 {
-				compatible = "ti,ina220";
-				reg = <0x40>;
-				shunt-resistor = <500>;
-			};
-
-			ina220@41 {
-				compatible = "ti,ina220";
-				reg = <0x41>;
-				shunt-resistor = <1000>;
-			};
-		};
-
-		i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x3>;
-
-			adt7481@4c {
-				compatible = "adi,adt7461";
-				reg = <0x4c>;
-			};
-		};
-	};
-};
-
-&i2c1 {
-	status = "disabled";
-};
-
-&i2c2 {
-	status = "disabled";
-};
-
-&i2c3 {
-	status = "disabled";
-};
-
-&dspi {
-	status = "okay";
-	dflash0: n25q128a {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "st,m25p80";
-		spi-max-frequency = <3000000>;
-		reg = <0>;
-	};
-	dflash1: sst25wf040b {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "st,m25p80";
-		spi-max-frequency = <3000000>;
-		reg = <1>;
-	};
-	dflash2: en25s64 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "st,m25p80";
-		spi-max-frequency = <3000000>;
-		reg = <2>;
-	};
-};
-
-&qspi {
-	status = "okay";
-	flash0: s25fl256s1@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "st,m25p80";
-		spi-max-frequency = <20000000>;
-		reg = <0>;
-	};
-	flash2: s25fl256s1@2 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "st,m25p80";
-		spi-max-frequency = <20000000>;
-		reg = <0>;
-	};
-};
-
-&sata0 {
-	status = "okay";
-};
-
-&sata1 {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-};
-
-&usb1 {
-	status = "okay";
-};
+#include "fsl-ls208xa-qds.dtsi"
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
index 2ff46ca..d5224fb 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
@@ -62,108 +62,4 @@
 	};
 };
 
-&esdhc {
-	status = "okay";
-};
-
-&ifc {
-	status = "okay";
-	#address-cells = <2>;
-	#size-cells = <1>;
-	ranges = <0x0 0x0 0x5 0x80000000 0x08000000
-		  0x2 0x0 0x5 0x30000000 0x00010000
-		  0x3 0x0 0x5 0x20000000 0x00010000>;
-
-	nor@0,0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "cfi-flash";
-		reg = <0x0 0x0 0x8000000>;
-		bank-width = <2>;
-		device-width = <1>;
-	};
-
-	nand@2,0 {
-	     compatible = "fsl,ifc-nand";
-	     reg = <0x2 0x0 0x10000>;
-	};
-
-	cpld@3,0 {
-	     reg = <0x3 0x0 0x10000>;
-	     compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis";
-	};
-
-};
-
-&i2c0 {
-	status = "okay";
-	pca9547@75 {
-		compatible = "nxp,pca9547";
-		reg = <0x75>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x01>;
-			rtc@68 {
-				compatible = "dallas,ds3232";
-				reg = <0x68>;
-			};
-		};
-
-		i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x3>;
-
-			adt7481@4c {
-				compatible = "adi,adt7461";
-				reg = <0x4c>;
-			};
-		};
-	};
-};
-
-&i2c1 {
-	status = "disabled";
-};
-
-&i2c2 {
-	status = "disabled";
-};
-
-&i2c3 {
-	status = "disabled";
-};
-
-&dspi {
-	status = "okay";
-	dflash0: n25q512a {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "st,m25p80";
-		spi-max-frequency = <3000000>;
-		reg = <0>;
-	};
-};
-
-&qspi {
-	status = "disabled";
-};
-
-&sata0 {
-	status = "okay";
-};
-
-&sata1 {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-};
-
-&usb1 {
-	status = "okay";
-};
+#include "fsl-ls208xa-rdb.dtsi"
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
index e5935f2..35801f3 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
@@ -1,8 +1,9 @@
 /*
  * Device Tree Include file for Freescale Layerscape-2080A family SoC.
  *
- * Copyright (C) 2014-2015, Freescale Semiconductor
+ * Copyright (C) 2014-2017, Freescale Semiconductor
  *
+ * Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
  * Bhupesh Sharma <bhupesh.sharma-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
  *
  * This file is dual-licensed: you can use it either under the terms
@@ -149,697 +150,25 @@
 		};
 	};
 
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x00000000 0x80000000 0 0x80000000>;
-		      /* DRAM space - 1, size : 2 GB DRAM */
-	};
-
-	sysclk: sysclk {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <100000000>;
-		clock-output-names = "sysclk";
-	};
-
-	gic: interrupt-controller@6000000 {
-		compatible = "arm,gic-v3";
-		reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */
-			<0x0 0x06100000 0 0x100000>, /* GICR (RD_base + SGI_base) */
-			<0x0 0x0c0c0000 0 0x2000>, /* GICC */
-			<0x0 0x0c0d0000 0 0x1000>, /* GICH */
-			<0x0 0x0c0e0000 0 0x20000>; /* GICV */
-		#interrupt-cells = <3>;
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-		interrupt-controller;
-		interrupts = <1 9 0x4>;
-
-		its: gic-its@6020000 {
-			compatible = "arm,gic-v3-its";
-			msi-controller;
-			reg = <0x0 0x6020000 0 0x20000>;
-		};
-	};
-
-	rstcr: syscon@1e60000 {
-		compatible = "fsl,ls2080a-rstcr", "syscon";
-		reg = <0x0 0x1e60000 0x0 0x4>;
-	};
-
-	reboot {
-		compatible ="syscon-reboot";
-		regmap = <&rstcr>;
-		offset = <0x0>;
-		mask = <0x2>;
-	};
-
-	timer {
-		compatible = "arm,armv8-timer";
-		interrupts = <1 13 4>, /* Physical Secure PPI, active-low */
-			     <1 14 4>, /* Physical Non-Secure PPI, active-low */
-			     <1 11 4>, /* Virtual PPI, active-low */
-			     <1 10 4>; /* Hypervisor PPI, active-low */
-		fsl,erratum-a008585;
-	};
-
-	pmu {
-		compatible = "arm,armv8-pmuv3";
-		interrupts = <1 7 0x8>; /* PMU PPI, Level low type */
-	};
-
-	soc {
-		compatible = "simple-bus";
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		clockgen: clocking@1300000 {
-			compatible = "fsl,ls2080a-clockgen";
-			reg = <0 0x1300000 0 0xa0000>;
-			#clock-cells = <2>;
-			clocks = <&sysclk>;
-		};
-
-		dcfg: dcfg@1e00000 {
-			compatible = "fsl,ls2080a-dcfg", "syscon";
-			reg = <0x0 0x1e00000 0x0 0x10000>;
-			little-endian;
-		};
-
-		tmu: tmu@1f80000 {
-			compatible = "fsl,qoriq-tmu";
-			reg = <0x0 0x1f80000 0x0 0x10000>;
-			interrupts = <0 23 0x4>;
-			fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
-			fsl,tmu-calibration = <0x00000000 0x00000026
-					       0x00000001 0x0000002d
-					       0x00000002 0x00000032
-					       0x00000003 0x00000039
-					       0x00000004 0x0000003f
-					       0x00000005 0x00000046
-					       0x00000006 0x0000004d
-					       0x00000007 0x00000054
-					       0x00000008 0x0000005a
-					       0x00000009 0x00000061
-					       0x0000000a 0x0000006a
-					       0x0000000b 0x00000071
-
-					       0x00010000 0x00000025
-					       0x00010001 0x0000002c
-					       0x00010002 0x00000035
-					       0x00010003 0x0000003d
-					       0x00010004 0x00000045
-					       0x00010005 0x0000004e
-					       0x00010006 0x00000057
-					       0x00010007 0x00000061
-					       0x00010008 0x0000006b
-					       0x00010009 0x00000076
-
-					       0x00020000 0x00000029
-					       0x00020001 0x00000033
-					       0x00020002 0x0000003d
-					       0x00020003 0x00000049
-					       0x00020004 0x00000056
-					       0x00020005 0x00000061
-					       0x00020006 0x0000006d
-
-					       0x00030000 0x00000021
-					       0x00030001 0x0000002a
-					       0x00030002 0x0000003c
-					       0x00030003 0x0000004e>;
-			little-endian;
-			#thermal-sensor-cells = <1>;
-		};
-
-		thermal-zones {
-			cpu_thermal: cpu-thermal {
-				polling-delay-passive = <1000>;
-				polling-delay = <5000>;
-
-				thermal-sensors = <&tmu 4>;
-
-				trips {
-					cpu_alert: cpu-alert {
-						temperature = <75000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-					cpu_crit: cpu-crit {
-						temperature = <85000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map0 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu0 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-					map1 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu2 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-					map2 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu4 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-					map3 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu6 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-				};
-			};
-		};
-
-		serial0: serial@21c0500 {
-			compatible = "fsl,ns16550", "ns16550a";
-			reg = <0x0 0x21c0500 0x0 0x100>;
-			clocks = <&clockgen 4 3>;
-			interrupts = <0 32 0x4>; /* Level high type */
-		};
-
-		serial1: serial@21c0600 {
-			compatible = "fsl,ns16550", "ns16550a";
-			reg = <0x0 0x21c0600 0x0 0x100>;
-			clocks = <&clockgen 4 3>;
-			interrupts = <0 32 0x4>; /* Level high type */
-		};
-
-		cluster1_core0_watchdog: wdt@c000000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
-			reg = <0x0 0xc000000 0x0 0x1000>;
-			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
-			clock-names = "apb_pclk", "wdog_clk";
-		};
-
-		cluster1_core1_watchdog: wdt@c010000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
-			reg = <0x0 0xc010000 0x0 0x1000>;
-			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
-			clock-names = "apb_pclk", "wdog_clk";
-		};
-
-		cluster2_core0_watchdog: wdt@c100000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
-			reg = <0x0 0xc100000 0x0 0x1000>;
-			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
-			clock-names = "apb_pclk", "wdog_clk";
-		};
-
-		cluster2_core1_watchdog: wdt@c110000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
-			reg = <0x0 0xc110000 0x0 0x1000>;
-			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
-			clock-names = "apb_pclk", "wdog_clk";
-		};
-
-		cluster3_core0_watchdog: wdt@c200000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
-			reg = <0x0 0xc200000 0x0 0x1000>;
-			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
-			clock-names = "apb_pclk", "wdog_clk";
-		};
-
-		cluster3_core1_watchdog: wdt@c210000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
-			reg = <0x0 0xc210000 0x0 0x1000>;
-			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
-			clock-names = "apb_pclk", "wdog_clk";
-		};
-
-		cluster4_core0_watchdog: wdt@c300000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
-			reg = <0x0 0xc300000 0x0 0x1000>;
-			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
-			clock-names = "apb_pclk", "wdog_clk";
-		};
-
-		cluster4_core1_watchdog: wdt@c310000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
-			reg = <0x0 0xc310000 0x0 0x1000>;
-			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
-			clock-names = "apb_pclk", "wdog_clk";
-		};
-
-		fsl_mc: fsl-mc@80c000000 {
-			compatible = "fsl,qoriq-mc";
-			reg = <0x00000008 0x0c000000 0 0x40>,	 /* MC portal base */
-			      <0x00000000 0x08340000 0 0x40000>; /* MC control reg */
-			msi-parent = <&its>;
-			#address-cells = <3>;
-			#size-cells = <1>;
-
-			/*
-			 * Region type 0x0 - MC portals
-			 * Region type 0x1 - QBMAN portals
-			 */
-			ranges = <0x0 0x0 0x0 0x8 0x0c000000 0x4000000
-				  0x1 0x0 0x0 0x8 0x18000000 0x8000000>;
-
-			/*
-			 * Define the maximum number of MACs present on the SoC.
-			 */
-			dpmacs {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				dpmac1: dpmac@1 {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0x1>;
-				};
-
-				dpmac2: dpmac@2 {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0x2>;
-				};
-
-				dpmac3: dpmac@3 {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0x3>;
-				};
-
-				dpmac4: dpmac@4 {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0x4>;
-				};
-
-				dpmac5: dpmac@5 {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0x5>;
-				};
-
-				dpmac6: dpmac@6 {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0x6>;
-				};
-
-				dpmac7: dpmac@7 {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0x7>;
-				};
-
-				dpmac8: dpmac@8 {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0x8>;
-				};
-
-				dpmac9: dpmac@9 {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0x9>;
-				};
-
-				dpmac10: dpmac@a {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0xa>;
-				};
-
-				dpmac11: dpmac@b {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0xb>;
-				};
-
-				dpmac12: dpmac@c {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0xc>;
-				};
-
-				dpmac13: dpmac@d {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0xd>;
-				};
-
-				dpmac14: dpmac@e {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0xe>;
-				};
-
-				dpmac15: dpmac@f {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0xf>;
-				};
-
-				dpmac16: dpmac@10 {
-					compatible = "fsl,qoriq-mc-dpmac";
-					reg = <0x10>;
-				};
-			};
-		};
-
-		smmu: iommu@5000000 {
-			compatible = "arm,mmu-500";
-			reg = <0 0x5000000 0 0x800000>;
-			#global-interrupts = <12>;
-			interrupts = <0 13 4>, /* global secure fault */
-				     <0 14 4>, /* combined secure interrupt */
-				     <0 15 4>, /* global non-secure fault */
-				     <0 16 4>, /* combined non-secure interrupt */
-				/* performance counter interrupts 0-7 */
-				     <0 211 4>, <0 212 4>,
-				     <0 213 4>, <0 214 4>,
-				     <0 215 4>, <0 216 4>,
-				     <0 217 4>, <0 218 4>,
-				/* per context interrupt, 64 interrupts */
-				     <0 146 4>, <0 147 4>,
-				     <0 148 4>, <0 149 4>,
-				     <0 150 4>, <0 151 4>,
-				     <0 152 4>, <0 153 4>,
-				     <0 154 4>, <0 155 4>,
-				     <0 156 4>, <0 157 4>,
-				     <0 158 4>, <0 159 4>,
-				     <0 160 4>, <0 161 4>,
-				     <0 162 4>, <0 163 4>,
-				     <0 164 4>, <0 165 4>,
-				     <0 166 4>, <0 167 4>,
-				     <0 168 4>, <0 169 4>,
-				     <0 170 4>, <0 171 4>,
-				     <0 172 4>, <0 173 4>,
-				     <0 174 4>, <0 175 4>,
-				     <0 176 4>, <0 177 4>,
-				     <0 178 4>, <0 179 4>,
-				     <0 180 4>, <0 181 4>,
-				     <0 182 4>, <0 183 4>,
-				     <0 184 4>, <0 185 4>,
-				     <0 186 4>, <0 187 4>,
-				     <0 188 4>, <0 189 4>,
-				     <0 190 4>, <0 191 4>,
-				     <0 192 4>, <0 193 4>,
-				     <0 194 4>, <0 195 4>,
-				     <0 196 4>, <0 197 4>,
-				     <0 198 4>, <0 199 4>,
-				     <0 200 4>, <0 201 4>,
-				     <0 202 4>, <0 203 4>,
-				     <0 204 4>, <0 205 4>,
-				     <0 206 4>, <0 207 4>,
-				     <0 208 4>, <0 209 4>;
-			mmu-masters = <&fsl_mc 0x300 0>;
-		};
-
-		dspi: dspi@2100000 {
-			status = "disabled";
-			compatible = "fsl,ls2080a-dspi", "fsl,ls2085a-dspi";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x0 0x2100000 0x0 0x10000>;
-			interrupts = <0 26 0x4>; /* Level high type */
-			clocks = <&clockgen 4 3>;
-			clock-names = "dspi";
-			spi-num-chipselects = <5>;
-			bus-num = <0>;
-		};
-
-		esdhc: esdhc@2140000 {
-			status = "disabled";
-			compatible = "fsl,ls2080a-esdhc", "fsl,esdhc";
-			reg = <0x0 0x2140000 0x0 0x10000>;
-			interrupts = <0 28 0x4>; /* Level high type */
-			clock-frequency = <0>;	/* Updated by bootloader */
-			voltage-ranges = <1800 1800 3300 3300>;
-			sdhci,auto-cmd12;
-			little-endian;
-			bus-width = <4>;
-		};
-
-		gpio0: gpio@2300000 {
-			compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio";
-			reg = <0x0 0x2300000 0x0 0x10000>;
-			interrupts = <0 36 0x4>; /* Level high type */
-			gpio-controller;
-			little-endian;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		gpio1: gpio@2310000 {
-			compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio";
-			reg = <0x0 0x2310000 0x0 0x10000>;
-			interrupts = <0 36 0x4>; /* Level high type */
-			gpio-controller;
-			little-endian;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		gpio2: gpio@2320000 {
-			compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio";
-			reg = <0x0 0x2320000 0x0 0x10000>;
-			interrupts = <0 37 0x4>; /* Level high type */
-			gpio-controller;
-			little-endian;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		gpio3: gpio@2330000 {
-			compatible = "fsl,ls2080a-gpio", "fsl,qoriq-gpio";
-			reg = <0x0 0x2330000 0x0 0x10000>;
-			interrupts = <0 37 0x4>; /* Level high type */
-			gpio-controller;
-			little-endian;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		i2c0: i2c@2000000 {
-			status = "disabled";
-			compatible = "fsl,vf610-i2c";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x0 0x2000000 0x0 0x10000>;
-			interrupts = <0 34 0x4>; /* Level high type */
-			clock-names = "i2c";
-			clocks = <&clockgen 4 3>;
-		};
-
-		i2c1: i2c@2010000 {
-			status = "disabled";
-			compatible = "fsl,vf610-i2c";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x0 0x2010000 0x0 0x10000>;
-			interrupts = <0 34 0x4>; /* Level high type */
-			clock-names = "i2c";
-			clocks = <&clockgen 4 3>;
-		};
-
-		i2c2: i2c@2020000 {
-			status = "disabled";
-			compatible = "fsl,vf610-i2c";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x0 0x2020000 0x0 0x10000>;
-			interrupts = <0 35 0x4>; /* Level high type */
-			clock-names = "i2c";
-			clocks = <&clockgen 4 3>;
-		};
-
-		i2c3: i2c@2030000 {
-			status = "disabled";
-			compatible = "fsl,vf610-i2c";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x0 0x2030000 0x0 0x10000>;
-			interrupts = <0 35 0x4>; /* Level high type */
-			clock-names = "i2c";
-			clocks = <&clockgen 4 3>;
-		};
-
-		ifc: ifc@2240000 {
-			compatible = "fsl,ifc", "simple-bus";
-			reg = <0x0 0x2240000 0x0 0x20000>;
-			interrupts = <0 21 0x4>; /* Level high type */
-			little-endian;
-			#address-cells = <2>;
-			#size-cells = <1>;
-
-			ranges = <0 0 0x5 0x80000000 0x08000000
-				  2 0 0x5 0x30000000 0x00010000
-				  3 0 0x5 0x20000000 0x00010000>;
-		};
-
-		qspi: quadspi@20c0000 {
-			status = "disabled";
-			compatible = "fsl,ls2080a-qspi", "fsl,ls1021a-qspi";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x0 0x20c0000 0x0 0x10000>,
-			      <0x0 0x20000000 0x0 0x10000000>;
-			reg-names = "QuadSPI", "QuadSPI-memory";
-			interrupts = <0 25 0x4>; /* Level high type */
-			clocks = <&clockgen 4 3>, <&clockgen 4 3>;
-			clock-names = "qspi_en", "qspi";
-		};
-
-		pcie@3400000 {
-			compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie",
-				     "snps,dw-pcie";
-			reg = <0x00 0x03400000 0x0 0x00100000   /* controller registers */
-			       0x10 0x00000000 0x0 0x00002000>; /* configuration space */
-			reg-names = "regs", "config";
-			interrupts = <0 108 0x4>; /* Level high type */
-			interrupt-names = "intr";
-			#address-cells = <3>;
-			#size-cells = <2>;
-			device_type = "pci";
-			dma-coherent;
-			num-lanes = <4>;
-			bus-range = <0x0 0xff>;
-			ranges = <0x81000000 0x0 0x00000000 0x10 0x00010000 0x0 0x00010000   /* downstream I/O */
-				  0x82000000 0x0 0x40000000 0x10 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 7>;
-			interrupt-map = <0000 0 0 1 &gic 0 0 0 109 4>,
-					<0000 0 0 2 &gic 0 0 0 110 4>,
-					<0000 0 0 3 &gic 0 0 0 111 4>,
-					<0000 0 0 4 &gic 0 0 0 112 4>;
-		};
-
-		pcie@3500000 {
-			compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie",
-				     "snps,dw-pcie";
-			reg = <0x00 0x03500000 0x0 0x00100000   /* controller registers */
-			       0x12 0x00000000 0x0 0x00002000>; /* configuration space */
-			reg-names = "regs", "config";
-			interrupts = <0 113 0x4>; /* Level high type */
-			interrupt-names = "intr";
-			#address-cells = <3>;
-			#size-cells = <2>;
-			device_type = "pci";
-			dma-coherent;
-			num-lanes = <4>;
-			bus-range = <0x0 0xff>;
-			ranges = <0x81000000 0x0 0x00000000 0x12 0x00010000 0x0 0x00010000   /* downstream I/O */
-				  0x82000000 0x0 0x40000000 0x12 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 7>;
-			interrupt-map = <0000 0 0 1 &gic 0 0 0 114 4>,
-					<0000 0 0 2 &gic 0 0 0 115 4>,
-					<0000 0 0 3 &gic 0 0 0 116 4>,
-					<0000 0 0 4 &gic 0 0 0 117 4>;
-		};
-
-		pcie@3600000 {
-			compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie",
-				     "snps,dw-pcie";
-			reg = <0x00 0x03600000 0x0 0x00100000   /* controller registers */
-			       0x14 0x00000000 0x0 0x00002000>; /* configuration space */
-			reg-names = "regs", "config";
-			interrupts = <0 118 0x4>; /* Level high type */
-			interrupt-names = "intr";
-			#address-cells = <3>;
-			#size-cells = <2>;
-			device_type = "pci";
-			dma-coherent;
-			num-lanes = <8>;
-			bus-range = <0x0 0xff>;
-			ranges = <0x81000000 0x0 0x00000000 0x14 0x00010000 0x0 0x00010000   /* downstream I/O */
-				  0x82000000 0x0 0x40000000 0x14 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 7>;
-			interrupt-map = <0000 0 0 1 &gic 0 0 0 119 4>,
-					<0000 0 0 2 &gic 0 0 0 120 4>,
-					<0000 0 0 3 &gic 0 0 0 121 4>,
-					<0000 0 0 4 &gic 0 0 0 122 4>;
-		};
-
-		pcie@3700000 {
-			compatible = "fsl,ls2080a-pcie", "fsl,ls2085a-pcie",
-				     "snps,dw-pcie";
-			reg = <0x00 0x03700000 0x0 0x00100000   /* controller registers */
-			       0x16 0x00000000 0x0 0x00002000>; /* configuration space */
-			reg-names = "regs", "config";
-			interrupts = <0 123 0x4>; /* Level high type */
-			interrupt-names = "intr";
-			#address-cells = <3>;
-			#size-cells = <2>;
-			device_type = "pci";
-			dma-coherent;
-			num-lanes = <4>;
-			bus-range = <0x0 0xff>;
-			ranges = <0x81000000 0x0 0x00000000 0x16 0x00010000 0x0 0x00010000   /* downstream I/O */
-				  0x82000000 0x0 0x40000000 0x16 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
-			msi-parent = <&its>;
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0 0 0 7>;
-			interrupt-map = <0000 0 0 1 &gic 0 0 0 124 4>,
-					<0000 0 0 2 &gic 0 0 0 125 4>,
-					<0000 0 0 3 &gic 0 0 0 126 4>,
-					<0000 0 0 4 &gic 0 0 0 127 4>;
-		};
-
-		sata0: sata@3200000 {
-			status = "disabled";
-			compatible = "fsl,ls2080a-ahci";
-			reg = <0x0 0x3200000 0x0 0x10000>;
-			interrupts = <0 133 0x4>; /* Level high type */
-			clocks = <&clockgen 4 3>;
-			dma-coherent;
-		};
-
-		sata1: sata@3210000 {
-			status = "disabled";
-			compatible = "fsl,ls2080a-ahci";
-			reg = <0x0 0x3210000 0x0 0x10000>;
-			interrupts = <0 136 0x4>; /* Level high type */
-			clocks = <&clockgen 4 3>;
-			dma-coherent;
-		};
-
-		usb0: usb3@3100000 {
-			status = "disabled";
-			compatible = "snps,dwc3";
-			reg = <0x0 0x3100000 0x0 0x10000>;
-			interrupts = <0 80 0x4>; /* Level high type */
-			dr_mode = "host";
-			snps,quirk-frame-length-adjustment = <0x20>;
-			snps,dis_rxdet_inp3_quirk;
-		};
-
-		usb1: usb3@3110000 {
-			status = "disabled";
-			compatible = "snps,dwc3";
-			reg = <0x0 0x3110000 0x0 0x10000>;
-			interrupts = <0 81 0x4>; /* Level high type */
-			dr_mode = "host";
-			snps,quirk-frame-length-adjustment = <0x20>;
-			snps,dis_rxdet_inp3_quirk;
-		};
-
-		ccn@4000000 {
-			compatible = "arm,ccn-504";
-			reg = <0x0 0x04000000 0x0 0x01000000>;
-			interrupts = <0 12 4>;
-		};
-	};
-
-	ddr1: memory-controller@1080000 {
-		compatible = "fsl,qoriq-memory-controller";
-		reg = <0x0 0x1080000 0x0 0x1000>;
-		interrupts = <0 17 0x4>;
-		little-endian;
-	};
+	#include "fsl-ls208xa.dtsi"
+};
 
-	ddr2: memory-controller@1090000 {
-		compatible = "fsl,qoriq-memory-controller";
-		reg = <0x0 0x1090000 0x0 0x1000>;
-		interrupts = <0 18 0x4>;
-		little-endian;
-	};
+&pcie1 {
+	ranges = <0x81000000 0x0 0x00000000 0x10 0x00010000 0x0 0x00010000   /* downstream I/O */
+		  0x82000000 0x0 0x40000000 0x10 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+};
+
+&pcie2 {
+	ranges = <0x81000000 0x0 0x00000000 0x12 0x00010000 0x0 0x00010000   /* downstream I/O */
+		  0x82000000 0x0 0x40000000 0x12 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+};
+
+&pcie3 {
+	ranges = <0x81000000 0x0 0x00000000 0x14 0x00010000 0x0 0x00010000   /* downstream I/O */
+		  0x82000000 0x0 0x40000000 0x14 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
 };
+
+&pcie4 {
+	ranges = <0x81000000 0x0 0x00000000 0x16 0x00010000 0x0 0x00010000   /* downstream I/O */
+		  0x82000000 0x0 0x40000000 0x16 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ };
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 3/3][v3] arm64: freescale: ls2088a: Add DTS support for FSL's LS2088A SoC

[Abhimanyu Saini]

This patch adds the device tree support for FSL LS2088A SoC based on
ARMv8 architecture.

Following levels of DTSI/DTS files have been created for the LS2088A
SoC family:

     - fsl-ls2088a.dtsi:
            DTS-Include file for FSL LS2088A SoC.

     - fsl-ls2088a-qds.dts:
            DTS file for FSL LS2088A QDS board.

     - fsl-ls2088a-rdb.dts:
            DTS file for FSL LS2088A RDB board.

Signed-off-by: Priyanka Jain <priyanka.jain-3arQi8VN3Tc@public.gmane.org>
Signed-off-by: Ashish Kumar <ashish.kumar-3arQi8VN3Tc@public.gmane.org>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
---
Changes for v2:
	- reorganize LS2088A device tree to use common
	  nodes from LS2080A device trees.

 arch/arm64/boot/dts/freescale/Makefile            |   2 +
 arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts |  65 +++++++++
 arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts |  65 +++++++++
 arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi    | 162 ++++++++++++++++++++++
 4 files changed, 294 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
 create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6602718..854868e 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -5,6 +5,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
  
 always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts
new file mode 100644
index 0000000..74bcb5d
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-qds.dts
@@ -0,0 +1,65 @@
+/*
+ * Device Tree file for Freescale LS2088A QDS Board.
+ *
+ * Copyright (C) 2015-17, Freescale Semiconductor
+ *
+ * Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "fsl-ls2088a.dtsi"
+
+/ {
+	model = "Freescale Layerscape 2088A QDS Board";
+	compatible = "fsl,ls2088a-qds", "fsl,ls2088a";
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+#include "fsl-ls208xa-qds.dtsi"
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
new file mode 100644
index 0000000..801eadd
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a-rdb.dts
@@ -0,0 +1,65 @@
+/*
+ * Device Tree file for Freescale LS2080a RDB Board.
+ *
+ * Copyright (C) 2015-17, Freescale Semiconductor
+ *
+ * Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "fsl-ls2088a.dtsi"
+
+/ {
+	model = "Freescale Layerscape 2088A RDB Board";
+	compatible = "fsl,ls2088a-rdb", "fsl,ls2088a";
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+#include "fsl-ls208xa-rdb.dtsi"
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi
new file mode 100644
index 0000000..f3e22d2
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi
@@ -0,0 +1,162 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-2088A family SoC.
+ *
+ * Copyright (C) 2015-17, Freescale Semiconductor
+ *
+ * Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+	compatible = "fsl,ls2080a";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x0>;
+			clocks = <&clockgen 1 0>;
+			next-level-cache = <&cluster0_l2>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x1>;
+			clocks = <&clockgen 1 0>;
+			next-level-cache = <&cluster0_l2>;
+		};
+
+		cpu2: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x100>;
+			clocks = <&clockgen 1 1>;
+			next-level-cache = <&cluster1_l2>;
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x101>;
+			clocks = <&clockgen 1 1>;
+			next-level-cache = <&cluster1_l2>;
+		};
+
+		cpu4: cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x200>;
+			clocks = <&clockgen 1 2>;
+			next-level-cache = <&cluster2_l2>;
+			#cooling-cells = <2>;
+		};
+
+		cpu5: cpu@201 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x201>;
+			clocks = <&clockgen 1 2>;
+			next-level-cache = <&cluster2_l2>;
+		};
+
+		cpu6: cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x300>;
+			clocks = <&clockgen 1 3>;
+			next-level-cache = <&cluster3_l2>;
+			#cooling-cells = <2>;
+		};
+
+		cpu7: cpu@301 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a72";
+			reg = <0x301>;
+			clocks = <&clockgen 1 3>;
+			next-level-cache = <&cluster3_l2>;
+		};
+
+		cluster0_l2: l2-cache0 {
+			compatible = "cache";
+		};
+
+		cluster1_l2: l2-cache1 {
+			compatible = "cache";
+		};
+
+		cluster2_l2: l2-cache2 {
+			compatible = "cache";
+		};
+
+		cluster3_l2: l2-cache3 {
+			compatible = "cache";
+		};
+	};
+	#include "fsl-ls208xa.dtsi"
+};
+
+&pcie1 {
+	ranges = <0x81000000 0x0 0x00000000 0x20 0x00010000 0x0 0x00010000
+		  0x82000000 0x0 0x40000000 0x20 0x40000000 0x0 0x40000000>;
+};
+
+&pcie2 {
+	ranges = <0x81000000 0x0 0x00000000 0x28 0x00010000 0x0 0x00010000
+		  0x82000000 0x0 0x40000000 0x28 0x40000000 0x0 0x40000000>;
+};
+
+&pcie3 {
+	ranges = <0x81000000 0x0 0x00000000 0x30 0x00010000 0x0 0x00010000
+		  0x82000000 0x0 0x40000000 0x30 0x40000000 0x0 0x40000000>;
+};
+
+&pcie4 {
+	ranges = <0x81000000 0x0 0x00000000 0x38 0x00010000 0x0 0x00010000
+		  0x82000000 0x0 0x40000000 0x38 0x40000000 0x0 0x40000000>;
+};
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/3][v3] arm64: freescale: ls2080a: Split devicetree for code resuability

[Shawn Guo]

On Mon, Jan 09, 2017 at 10:44:55AM +0530, Abhimanyu Saini wrote:
> LS2088A and LS2080A are similar SoCs with a few differences like
> ARM cores etc.
> 
> Reorganize the LS2080A device tree to move the common nodes to:
>         - fsl-ls208xa.dtsi
>         - fsl-ls208xa-rdb.dtsi
>         - fsl-ls208xa-qds.dtsi

These 3 new files are missing.

> 
> Signed-off-by: Priyanka Jain <priyanka.jain-3arQi8VN3Tc@public.gmane.org>
> Signed-off-by: Ashish Kumar <ashish.kumar-3arQi8VN3Tc@public.gmane.org>
> Signed-off-by: Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
> ---
> Changes for v3:
>         - rename dts/dtsi files
> 
>  arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts | 154 +----
>  arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts | 106 +---
>  arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi    | 715 +---------------------
>  3 files changed, 26 insertions(+), 949 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
> index 8bc1f8f..3cf4a5c 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
> @@ -1,8 +1,9 @@
>  /*
>   * Device Tree file for Freescale LS2080a QDS Board.
>   *
> - * Copyright (C) 2015, Freescale Semiconductor
> + * Copyright (C) 2015-17, Freescale Semiconductor
>   *
> + * Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
>   * Bhupesh Sharma <bhupesh.sharma-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
>   *
>   * This file is dual-licensed: you can use it either under the terms

<snip>

> -&sata0 {
> -	status = "okay";
> -};
> -
> -&sata1 {
> -	status = "okay";
> -};
> -
> -&usb0 {
> -	status = "okay";
> -};
> -
> -&usb1 {
> -	status = "okay";
> -};
> +#include "fsl-ls208xa-qds.dtsi"

Can we put such includes just at the beginning of the file (after
licence section)?

> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
> index 2ff46ca..d5224fb 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
> @@ -62,108 +62,4 @@
>  	};
>  };
>  

<snip>

> -&usb0 {
> -	status = "okay";
> -};
> -
> -&usb1 {
> -	status = "okay";
> -};
> +#include "fsl-ls208xa-rdb.dtsi"

Ditto

> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
> index e5935f2..35801f3 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
> @@ -1,8 +1,9 @@
>  /*
>   * Device Tree Include file for Freescale Layerscape-2080A family SoC.
>   *
> - * Copyright (C) 2014-2015, Freescale Semiconductor
> + * Copyright (C) 2014-2017, Freescale Semiconductor
>   *
> + * Abhimanyu Saini <abhimanyu.saini-3arQi8VN3Tc@public.gmane.org>
>   * Bhupesh Sharma <bhupesh.sharma-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
>   *
>   * This file is dual-licensed: you can use it either under the terms
> @@ -149,697 +150,25 @@
>  		};
>  	};
>  
> -	memory@80000000 {
> -		device_type = "memory";
> -		reg = <0x00000000 0x80000000 0 0x80000000>;
> -		      /* DRAM space - 1, size : 2 GB DRAM */
> -	};

<snip>

> -	ddr1: memory-controller@1080000 {
> -		compatible = "fsl,qoriq-memory-controller";
> -		reg = <0x0 0x1080000 0x0 0x1000>;
> -		interrupts = <0 17 0x4>;
> -		little-endian;
> -	};
> +	#include "fsl-ls208xa.dtsi"

Ditto

Shawn

> +};
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/3][v3] arm64: freescale: ls2080a: Split devicetree for code resuability

[Shawn Guo]

On Mon, Jan 09, 2017 at 10:44:55AM +0530, Abhimanyu Saini wrote:
> LS2088A and LS2080A are similar SoCs with a few differences like
> ARM cores etc.
> 
> Reorganize the LS2080A device tree to move the common nodes to:
>         - fsl-ls208xa.dtsi
>         - fsl-ls208xa-rdb.dtsi
>         - fsl-ls208xa-qds.dtsi

These 3 new files are missing.

> 
> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
> Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
> ---
> Changes for v3:
>         - rename dts/dtsi files
> 
>  arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts | 154 +----
>  arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts | 106 +---
>  arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi    | 715 +---------------------
>  3 files changed, 26 insertions(+), 949 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
> index 8bc1f8f..3cf4a5c 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
> @@ -1,8 +1,9 @@
>  /*
>   * Device Tree file for Freescale LS2080a QDS Board.
>   *
> - * Copyright (C) 2015, Freescale Semiconductor
> + * Copyright (C) 2015-17, Freescale Semiconductor
>   *
> + * Abhimanyu Saini <abhimanyu.saini@nxp.com>
>   * Bhupesh Sharma <bhupesh.sharma@freescale.com>
>   *
>   * This file is dual-licensed: you can use it either under the terms

<snip>

> -&sata0 {
> -	status = "okay";
> -};
> -
> -&sata1 {
> -	status = "okay";
> -};
> -
> -&usb0 {
> -	status = "okay";
> -};
> -
> -&usb1 {
> -	status = "okay";
> -};
> +#include "fsl-ls208xa-qds.dtsi"

Can we put such includes just at the beginning of the file (after
licence section)?

> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
> index 2ff46ca..d5224fb 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
> @@ -62,108 +62,4 @@
>  	};
>  };
>  

<snip>

> -&usb0 {
> -	status = "okay";
> -};
> -
> -&usb1 {
> -	status = "okay";
> -};
> +#include "fsl-ls208xa-rdb.dtsi"

Ditto

> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
> index e5935f2..35801f3 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
> @@ -1,8 +1,9 @@
>  /*
>   * Device Tree Include file for Freescale Layerscape-2080A family SoC.
>   *
> - * Copyright (C) 2014-2015, Freescale Semiconductor
> + * Copyright (C) 2014-2017, Freescale Semiconductor
>   *
> + * Abhimanyu Saini <abhimanyu.saini@nxp.com>
>   * Bhupesh Sharma <bhupesh.sharma@freescale.com>
>   *
>   * This file is dual-licensed: you can use it either under the terms
> @@ -149,697 +150,25 @@
>  		};
>  	};
>  
> -	memory at 80000000 {
> -		device_type = "memory";
> -		reg = <0x00000000 0x80000000 0 0x80000000>;
> -		      /* DRAM space - 1, size : 2 GB DRAM */
> -	};

<snip>

> -	ddr1: memory-controller at 1080000 {
> -		compatible = "fsl,qoriq-memory-controller";
> -		reg = <0x0 0x1080000 0x0 0x1000>;
> -		interrupts = <0 17 0x4>;
> -		little-endian;
> -	};
> +	#include "fsl-ls208xa.dtsi"

Ditto

Shawn

> +};

Re: [PATCH 0/3][v3] Add QorIQ LS2088A platform support

[Shawn Guo]

On Mon, Jan 09, 2017 at 10:44:53AM +0530, Abhimanyu Saini wrote:
> Abhimanyu Saini (3):
>   dt-bindings: Add compatible for LS2088A QDS and RDB board
>   arm64: freescale: ls2080a: Split devicetree for code resuability

"arm64: dts: ls2080a: ..."

>   arm64: freescale: ls2088a: Add DTS support for FSL's LS2088A SoC

"arm64: dts: ls2088a: ..."

Shawn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 0/3][v3] Add QorIQ LS2088A platform support

[Shawn Guo]

On Mon, Jan 09, 2017 at 10:44:53AM +0530, Abhimanyu Saini wrote:
> Abhimanyu Saini (3):
>   dt-bindings: Add compatible for LS2088A QDS and RDB board
>   arm64: freescale: ls2080a: Split devicetree for code resuability

"arm64: dts: ls2080a: ..."

>   arm64: freescale: ls2088a: Add DTS support for FSL's LS2088A SoC

"arm64: dts: ls2088a: ..."

Shawn