* [PATCH v5 0/2] Support for Axentia TSE-850
@ 2017-01-10 8:08 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-kernel
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Alexandre Belloni,
Jean-Christophe Plagniol-Villard, linux-arm-kernel, devicetree
Hi!
changes v4 -> v5
- comment from Rob about the memory node made me look closer and
the memory size is actually updated by the bootloader, and that
hid the fact that the entry was always faulty. This version
specifies the correct memory size from the start, which is 64MB.
- ack from Rob
changes v3 -> v4
- rename files arch/arm/boot/dts/axentia-* to .../at91-*
- remove bootargs from at91-tse850-3.dts
- depend on the atmel ssc to register as a sound dai by itself
- bump copyright years
changes v2 -> v3
- document the new compatible strings prefixed with "axentia,".
changes v1 -> v2
- squash the fixup into the correct patch, sorry for the noise.
After finally having all essintial drivers upstreamed I would
like to have the dts and the defconfig also upstreamed.
The atmel-ssc/sound-dai change depends on a change that has been
sitting in the ASoC tree since mid-december, and I have been waiting
for it to hit linux-next before sending this, but it seems to take
longer than I anticipated. So, since I do not want this to in
turn miss the next merge window because of that wait I therefore
request that this is taken now even though it doesn't really work
w/o the ASoC "topic/atmel" branch as of 2016-12-15 [1]. It of course
builds cleanly even w/o those ASoC changes. That effectively means
that noone besides me should notice the inconsistency (I currently
have all affected devices under my control).
Cheers,
peda
[1] http://git.kernel.org/cgit/linux/kernel/git/broonie/sound.git/log/?h=topic/atmel
Peter Rosin (2):
ARM: dts: at91: add devicetree for the Axentia TSE-850
ARM: sama5_defconfig: add support for the Axentia TSE-850 board
Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
MAINTAINERS | 8 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
arch/arm/configs/sama5_defconfig | 7 +-
6 files changed, 361 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
--
2.1.4
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v5 0/2] Support for Axentia TSE-850
@ 2017-01-10 8:08 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Alexandre Belloni,
Jean-Christophe Plagniol-Villard,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
Hi!
changes v4 -> v5
- comment from Rob about the memory node made me look closer and
the memory size is actually updated by the bootloader, and that
hid the fact that the entry was always faulty. This version
specifies the correct memory size from the start, which is 64MB.
- ack from Rob
changes v3 -> v4
- rename files arch/arm/boot/dts/axentia-* to .../at91-*
- remove bootargs from at91-tse850-3.dts
- depend on the atmel ssc to register as a sound dai by itself
- bump copyright years
changes v2 -> v3
- document the new compatible strings prefixed with "axentia,".
changes v1 -> v2
- squash the fixup into the correct patch, sorry for the noise.
After finally having all essintial drivers upstreamed I would
like to have the dts and the defconfig also upstreamed.
The atmel-ssc/sound-dai change depends on a change that has been
sitting in the ASoC tree since mid-december, and I have been waiting
for it to hit linux-next before sending this, but it seems to take
longer than I anticipated. So, since I do not want this to in
turn miss the next merge window because of that wait I therefore
request that this is taken now even though it doesn't really work
w/o the ASoC "topic/atmel" branch as of 2016-12-15 [1]. It of course
builds cleanly even w/o those ASoC changes. That effectively means
that noone besides me should notice the inconsistency (I currently
have all affected devices under my control).
Cheers,
peda
[1] http://git.kernel.org/cgit/linux/kernel/git/broonie/sound.git/log/?h=topic/atmel
Peter Rosin (2):
ARM: dts: at91: add devicetree for the Axentia TSE-850
ARM: sama5_defconfig: add support for the Axentia TSE-850 board
Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
MAINTAINERS | 8 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
arch/arm/configs/sama5_defconfig | 7 +-
6 files changed, 361 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v5 0/2] Support for Axentia TSE-850
@ 2017-01-10 8:08 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-arm-kernel
Hi!
changes v4 -> v5
- comment from Rob about the memory node made me look closer and
the memory size is actually updated by the bootloader, and that
hid the fact that the entry was always faulty. This version
specifies the correct memory size from the start, which is 64MB.
- ack from Rob
changes v3 -> v4
- rename files arch/arm/boot/dts/axentia-* to .../at91-*
- remove bootargs from at91-tse850-3.dts
- depend on the atmel ssc to register as a sound dai by itself
- bump copyright years
changes v2 -> v3
- document the new compatible strings prefixed with "axentia,".
changes v1 -> v2
- squash the fixup into the correct patch, sorry for the noise.
After finally having all essintial drivers upstreamed I would
like to have the dts and the defconfig also upstreamed.
The atmel-ssc/sound-dai change depends on a change that has been
sitting in the ASoC tree since mid-december, and I have been waiting
for it to hit linux-next before sending this, but it seems to take
longer than I anticipated. So, since I do not want this to in
turn miss the next merge window because of that wait I therefore
request that this is taken now even though it doesn't really work
w/o the ASoC "topic/atmel" branch as of 2016-12-15 [1]. It of course
builds cleanly even w/o those ASoC changes. That effectively means
that noone besides me should notice the inconsistency (I currently
have all affected devices under my control).
Cheers,
peda
[1] http://git.kernel.org/cgit/linux/kernel/git/broonie/sound.git/log/?h=topic/atmel
Peter Rosin (2):
ARM: dts: at91: add devicetree for the Axentia TSE-850
ARM: sama5_defconfig: add support for the Axentia TSE-850 board
Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
MAINTAINERS | 8 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
arch/arm/configs/sama5_defconfig | 7 +-
6 files changed, 361 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
--
2.1.4
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 8:08 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-kernel
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Alexandre Belloni,
Jean-Christophe Plagniol-Villard, linux-arm-kernel, devicetree
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
---
Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
MAINTAINERS | 8 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
5 files changed, 355 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt
new file mode 100644
index 000000000000..ea3fb96ae465
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/axentia.txt
@@ -0,0 +1,19 @@
+Device tree bindings for Axentia ARM devices
+============================================
+
+Linea CPU module
+----------------
+
+Required root node properties:
+compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+and following the rules from atmel-at91.txt for a sama5d31 SoC.
+
+
+TSE-850 v3 board
+----------------
+
+Required root node properties:
+compatible = "axentia,tse850v3", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+and following the rules from above for the axentia,linea CPU module.
diff --git a/MAINTAINERS b/MAINTAINERS
index 97b78cc5aa51..5c2ea6e9cd7f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2346,6 +2346,14 @@ S: Maintained
F: Documentation/devicetree/bindings/sound/axentia,*
F: sound/soc/atmel/tse850-pcm5142.c
+AXENTIA ARM DEVICES
+M: Peter Rosin <peda@axentia.se>
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S: Maintained
+F: Documentation/devicetree/bindings/arm/axentia.txt
+F: arch/arm/boot/dts/at91-linea.dtsi
+F: arch/arm/boot/dts/at91-tse850-3.dts
+
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
M: Mauro Carvalho Chehab <mchehab@kernel.org>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9a7375c388a8..7632849866de 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
+ at91-tse850-3.dtb \
sama5d31ek.dtb \
sama5d33ek.dtb \
sama5d34ek.dtb \
diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/at91-linea.dtsi
new file mode 100644
index 000000000000..646feb0daa81
--- /dev/null
+++ b/arch/arm/boot/dts/at91-linea.dtsi
@@ -0,0 +1,53 @@
+/*
+ * at91-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
+ *
+ * Copyright (C) 2017 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "sama5d31.dtsi"
+
+/ {
+ compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+};
+
+&slow_xtal {
+ clock-frequency = <32768>;
+};
+
+&main_xtal {
+ clock-frequency = <12000000>;
+};
+
+&main {
+ clock-frequency = <12000000>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ eeprom@51 {
+ compatible = "st,24c64";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&nand0 {
+ status = "okay";
+
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+};
diff --git a/arch/arm/boot/dts/at91-tse850-3.dts b/arch/arm/boot/dts/at91-tse850-3.dts
new file mode 100644
index 000000000000..669a2c6bdefc
--- /dev/null
+++ b/arch/arm/boot/dts/at91-tse850-3.dts
@@ -0,0 +1,274 @@
+/*
+ * at91-tse850-3.dts - Device Tree file for the Axentia TSE-850 3.0 board
+ *
+ * Copyright (C) 2017 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "at91-linea.dtsi"
+
+/ {
+ model = "Axentia TSE-850 3.0";
+ compatible = "axentia,tse850v3", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ pinctrl@fffff200 {
+ tse850 {
+ pinctrl_usba_vbus: usba-vbus {
+ atmel,pins =
+ <AT91_PIOC 31
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_DEGLITCH>;
+ };
+ };
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+ };
+ };
+
+ sck: oscillator {
+ compatible = "fixed-clock";
+
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
+ clock-output-names = "sck";
+ };
+
+ reg_3v3: regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "3v3-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ana: reg-ana {
+ compatible = "pwm-regulator";
+
+ regulator-name = "ANA";
+
+ pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+ pwm-dutycycle-unit = <1000>;
+ pwm-dutycycle-range = <100 1000>;
+
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <20000000>;
+ regulator-ramp-delay = <1000>;
+ };
+
+ sound {
+ compatible = "axentia,tse850-pcm5142";
+
+ axentia,cpu-dai = <&ssc0>;
+ axentia,audio-codec = <&pcm5142>;
+
+ axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+ axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+ axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+ axentia,ana-supply = <&ana>;
+ };
+
+ dac: dpot-dac {
+ compatible = "dpot-dac";
+ vref-supply = <®_3v3>;
+ io-channels = <&dpot 0>;
+ io-channel-names = "dpot";
+ #io-channel-cells = <1>;
+ };
+
+ envelope-detector {
+ compatible = "axentia,tse850-envelope-detector";
+ io-channels = <&dac 0>;
+ io-channel-names = "dac";
+
+ interrupt-parent = <&pioA>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "comp";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ch1-red {
+ label = "ch-1:red";
+ gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+ };
+ ch1-green {
+ label = "ch-1:green";
+ gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
+ };
+ ch2-red {
+ label = "ch-2:red";
+ gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
+ };
+ ch2-green {
+ label = "ch-2:green";
+ gpios = <&pioA 20 GPIO_ACTIVE_LOW>;
+ };
+ data-red {
+ label = "data:red";
+ gpios = <&pioA 19 GPIO_ACTIVE_LOW>;
+ };
+ data-green {
+ label = "data:green";
+ gpios = <&pioA 18 GPIO_ACTIVE_LOW>;
+ };
+ alarm-red {
+ label = "alarm:red";
+ gpios = <&pioA 17 GPIO_ACTIVE_LOW>;
+ };
+ alarm-green {
+ label = "alarm:green";
+ gpios = <&pioA 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&nand0 {
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ barebox@40000 {
+ label = "bootloader";
+ reg = <0x40000 0x60000>;
+ };
+
+ bareboxenv@c0000 {
+ label = "bareboxenv";
+ reg = <0xc0000 0x40000>;
+ };
+
+ bareboxenv2@100000 {
+ label = "bareboxenv2";
+ reg = <0x100000 0x40000>;
+ };
+
+ oftree@180000 {
+ label = "oftree";
+ reg = <0x180000 0x20000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x500000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+
+ ovlfs@10000000 {
+ label = "ovlfs";
+ reg = <0x10000000 0x10000000>;
+ };
+};
+
+&ssc0 {
+ #sound-dai-cells = <0>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ jc42@18 {
+ compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+ reg = <0x18>;
+ };
+
+ dpot: mcp4651-104@28 {
+ compatible = "microchip,mcp4651-104";
+ reg = <0x28>;
+ #io-channel-cells = <1>;
+ };
+
+ pcm5142: pcm5142@4c {
+ compatible = "ti,pcm5142";
+
+ reg = <0x4c>;
+
+ AVDD-supply = <®_3v3>;
+ DVDD-supply = <®_3v3>;
+ CPVDD-supply = <®_3v3>;
+
+ clocks = <&sck>;
+
+ pll-in = <3>;
+ pll-out = <6>;
+ };
+
+ eeprom@50 {
+ compatible = "nxp,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+&usart0 {
+ status = "okay";
+
+ atmel,use-dma-rx;
+};
+
+&pwm0 {
+ status = "okay";
+
+ pinctrl-0 = <&pinctrl_pwm0_pwml2_1>;
+ pinctrl-names = "default";
+};
+
+&macb1 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@3 {
+ reg = <3>;
+
+ interrupt-parent = <&pioE>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ atmel,vbus-gpio = <&pioC 31 GPIO_ACTIVE_HIGH>;
+};
+
+&usb1 {
+ status = "okay";
+
+ num-ports = <1>;
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ atmel,oc-gpio = <&pioC 15 GPIO_ACTIVE_LOW>;
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 8:08 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Alexandre Belloni,
Jean-Christophe Plagniol-Villard,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
---
Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
MAINTAINERS | 8 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
5 files changed, 355 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt
new file mode 100644
index 000000000000..ea3fb96ae465
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/axentia.txt
@@ -0,0 +1,19 @@
+Device tree bindings for Axentia ARM devices
+============================================
+
+Linea CPU module
+----------------
+
+Required root node properties:
+compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+and following the rules from atmel-at91.txt for a sama5d31 SoC.
+
+
+TSE-850 v3 board
+----------------
+
+Required root node properties:
+compatible = "axentia,tse850v3", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+and following the rules from above for the axentia,linea CPU module.
diff --git a/MAINTAINERS b/MAINTAINERS
index 97b78cc5aa51..5c2ea6e9cd7f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2346,6 +2346,14 @@ S: Maintained
F: Documentation/devicetree/bindings/sound/axentia,*
F: sound/soc/atmel/tse850-pcm5142.c
+AXENTIA ARM DEVICES
+M: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
+L: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org (moderated for non-subscribers)
+S: Maintained
+F: Documentation/devicetree/bindings/arm/axentia.txt
+F: arch/arm/boot/dts/at91-linea.dtsi
+F: arch/arm/boot/dts/at91-tse850-3.dts
+
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab-JsYNTwtnfakRB7SZvlqPiA@public.gmane.org>
M: Mauro Carvalho Chehab <mchehab-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9a7375c388a8..7632849866de 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
+ at91-tse850-3.dtb \
sama5d31ek.dtb \
sama5d33ek.dtb \
sama5d34ek.dtb \
diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/at91-linea.dtsi
new file mode 100644
index 000000000000..646feb0daa81
--- /dev/null
+++ b/arch/arm/boot/dts/at91-linea.dtsi
@@ -0,0 +1,53 @@
+/*
+ * at91-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
+ *
+ * Copyright (C) 2017 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "sama5d31.dtsi"
+
+/ {
+ compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+};
+
+&slow_xtal {
+ clock-frequency = <32768>;
+};
+
+&main_xtal {
+ clock-frequency = <12000000>;
+};
+
+&main {
+ clock-frequency = <12000000>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ eeprom@51 {
+ compatible = "st,24c64";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&nand0 {
+ status = "okay";
+
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+};
diff --git a/arch/arm/boot/dts/at91-tse850-3.dts b/arch/arm/boot/dts/at91-tse850-3.dts
new file mode 100644
index 000000000000..669a2c6bdefc
--- /dev/null
+++ b/arch/arm/boot/dts/at91-tse850-3.dts
@@ -0,0 +1,274 @@
+/*
+ * at91-tse850-3.dts - Device Tree file for the Axentia TSE-850 3.0 board
+ *
+ * Copyright (C) 2017 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "at91-linea.dtsi"
+
+/ {
+ model = "Axentia TSE-850 3.0";
+ compatible = "axentia,tse850v3", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ pinctrl@fffff200 {
+ tse850 {
+ pinctrl_usba_vbus: usba-vbus {
+ atmel,pins =
+ <AT91_PIOC 31
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_DEGLITCH>;
+ };
+ };
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+ };
+ };
+
+ sck: oscillator {
+ compatible = "fixed-clock";
+
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
+ clock-output-names = "sck";
+ };
+
+ reg_3v3: regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "3v3-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ana: reg-ana {
+ compatible = "pwm-regulator";
+
+ regulator-name = "ANA";
+
+ pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+ pwm-dutycycle-unit = <1000>;
+ pwm-dutycycle-range = <100 1000>;
+
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <20000000>;
+ regulator-ramp-delay = <1000>;
+ };
+
+ sound {
+ compatible = "axentia,tse850-pcm5142";
+
+ axentia,cpu-dai = <&ssc0>;
+ axentia,audio-codec = <&pcm5142>;
+
+ axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+ axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+ axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+ axentia,ana-supply = <&ana>;
+ };
+
+ dac: dpot-dac {
+ compatible = "dpot-dac";
+ vref-supply = <®_3v3>;
+ io-channels = <&dpot 0>;
+ io-channel-names = "dpot";
+ #io-channel-cells = <1>;
+ };
+
+ envelope-detector {
+ compatible = "axentia,tse850-envelope-detector";
+ io-channels = <&dac 0>;
+ io-channel-names = "dac";
+
+ interrupt-parent = <&pioA>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "comp";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ch1-red {
+ label = "ch-1:red";
+ gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+ };
+ ch1-green {
+ label = "ch-1:green";
+ gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
+ };
+ ch2-red {
+ label = "ch-2:red";
+ gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
+ };
+ ch2-green {
+ label = "ch-2:green";
+ gpios = <&pioA 20 GPIO_ACTIVE_LOW>;
+ };
+ data-red {
+ label = "data:red";
+ gpios = <&pioA 19 GPIO_ACTIVE_LOW>;
+ };
+ data-green {
+ label = "data:green";
+ gpios = <&pioA 18 GPIO_ACTIVE_LOW>;
+ };
+ alarm-red {
+ label = "alarm:red";
+ gpios = <&pioA 17 GPIO_ACTIVE_LOW>;
+ };
+ alarm-green {
+ label = "alarm:green";
+ gpios = <&pioA 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&nand0 {
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ barebox@40000 {
+ label = "bootloader";
+ reg = <0x40000 0x60000>;
+ };
+
+ bareboxenv@c0000 {
+ label = "bareboxenv";
+ reg = <0xc0000 0x40000>;
+ };
+
+ bareboxenv2@100000 {
+ label = "bareboxenv2";
+ reg = <0x100000 0x40000>;
+ };
+
+ oftree@180000 {
+ label = "oftree";
+ reg = <0x180000 0x20000>;
+ };
+
+ kernel@200000 {
+ label = "kernel";
+ reg = <0x200000 0x500000>;
+ };
+
+ rootfs@800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+
+ ovlfs@10000000 {
+ label = "ovlfs";
+ reg = <0x10000000 0x10000000>;
+ };
+};
+
+&ssc0 {
+ #sound-dai-cells = <0>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ jc42@18 {
+ compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+ reg = <0x18>;
+ };
+
+ dpot: mcp4651-104@28 {
+ compatible = "microchip,mcp4651-104";
+ reg = <0x28>;
+ #io-channel-cells = <1>;
+ };
+
+ pcm5142: pcm5142@4c {
+ compatible = "ti,pcm5142";
+
+ reg = <0x4c>;
+
+ AVDD-supply = <®_3v3>;
+ DVDD-supply = <®_3v3>;
+ CPVDD-supply = <®_3v3>;
+
+ clocks = <&sck>;
+
+ pll-in = <3>;
+ pll-out = <6>;
+ };
+
+ eeprom@50 {
+ compatible = "nxp,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+&usart0 {
+ status = "okay";
+
+ atmel,use-dma-rx;
+};
+
+&pwm0 {
+ status = "okay";
+
+ pinctrl-0 = <&pinctrl_pwm0_pwml2_1>;
+ pinctrl-names = "default";
+};
+
+&macb1 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@3 {
+ reg = <3>;
+
+ interrupt-parent = <&pioE>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ atmel,vbus-gpio = <&pioC 31 GPIO_ACTIVE_HIGH>;
+};
+
+&usb1 {
+ status = "okay";
+
+ num-ports = <1>;
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ atmel,oc-gpio = <&pioC 15 GPIO_ACTIVE_LOW>;
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+};
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 8:08 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-arm-kernel
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
---
Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
MAINTAINERS | 8 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
5 files changed, 355 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt
new file mode 100644
index 000000000000..ea3fb96ae465
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/axentia.txt
@@ -0,0 +1,19 @@
+Device tree bindings for Axentia ARM devices
+============================================
+
+Linea CPU module
+----------------
+
+Required root node properties:
+compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+and following the rules from atmel-at91.txt for a sama5d31 SoC.
+
+
+TSE-850 v3 board
+----------------
+
+Required root node properties:
+compatible = "axentia,tse850v3", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+and following the rules from above for the axentia,linea CPU module.
diff --git a/MAINTAINERS b/MAINTAINERS
index 97b78cc5aa51..5c2ea6e9cd7f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2346,6 +2346,14 @@ S: Maintained
F: Documentation/devicetree/bindings/sound/axentia,*
F: sound/soc/atmel/tse850-pcm5142.c
+AXENTIA ARM DEVICES
+M: Peter Rosin <peda@axentia.se>
+L: linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
+S: Maintained
+F: Documentation/devicetree/bindings/arm/axentia.txt
+F: arch/arm/boot/dts/at91-linea.dtsi
+F: arch/arm/boot/dts/at91-tse850-3.dts
+
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
M: Mauro Carvalho Chehab <mchehab@kernel.org>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9a7375c388a8..7632849866de 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
+ at91-tse850-3.dtb \
sama5d31ek.dtb \
sama5d33ek.dtb \
sama5d34ek.dtb \
diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/at91-linea.dtsi
new file mode 100644
index 000000000000..646feb0daa81
--- /dev/null
+++ b/arch/arm/boot/dts/at91-linea.dtsi
@@ -0,0 +1,53 @@
+/*
+ * at91-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
+ *
+ * Copyright (C) 2017 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "sama5d31.dtsi"
+
+/ {
+ compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+};
+
+&slow_xtal {
+ clock-frequency = <32768>;
+};
+
+&main_xtal {
+ clock-frequency = <12000000>;
+};
+
+&main {
+ clock-frequency = <12000000>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ eeprom at 51 {
+ compatible = "st,24c64";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&nand0 {
+ status = "okay";
+
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+};
diff --git a/arch/arm/boot/dts/at91-tse850-3.dts b/arch/arm/boot/dts/at91-tse850-3.dts
new file mode 100644
index 000000000000..669a2c6bdefc
--- /dev/null
+++ b/arch/arm/boot/dts/at91-tse850-3.dts
@@ -0,0 +1,274 @@
+/*
+ * at91-tse850-3.dts - Device Tree file for the Axentia TSE-850 3.0 board
+ *
+ * Copyright (C) 2017 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "at91-linea.dtsi"
+
+/ {
+ model = "Axentia TSE-850 3.0";
+ compatible = "axentia,tse850v3", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ pinctrl at fffff200 {
+ tse850 {
+ pinctrl_usba_vbus: usba-vbus {
+ atmel,pins =
+ <AT91_PIOC 31
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_DEGLITCH>;
+ };
+ };
+ };
+
+ watchdog at fffffe40 {
+ status = "okay";
+ };
+ };
+ };
+
+ sck: oscillator {
+ compatible = "fixed-clock";
+
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
+ clock-output-names = "sck";
+ };
+
+ reg_3v3: regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "3v3-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ana: reg-ana {
+ compatible = "pwm-regulator";
+
+ regulator-name = "ANA";
+
+ pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+ pwm-dutycycle-unit = <1000>;
+ pwm-dutycycle-range = <100 1000>;
+
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <20000000>;
+ regulator-ramp-delay = <1000>;
+ };
+
+ sound {
+ compatible = "axentia,tse850-pcm5142";
+
+ axentia,cpu-dai = <&ssc0>;
+ axentia,audio-codec = <&pcm5142>;
+
+ axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+ axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+ axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+ axentia,ana-supply = <&ana>;
+ };
+
+ dac: dpot-dac {
+ compatible = "dpot-dac";
+ vref-supply = <®_3v3>;
+ io-channels = <&dpot 0>;
+ io-channel-names = "dpot";
+ #io-channel-cells = <1>;
+ };
+
+ envelope-detector {
+ compatible = "axentia,tse850-envelope-detector";
+ io-channels = <&dac 0>;
+ io-channel-names = "dac";
+
+ interrupt-parent = <&pioA>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "comp";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ch1-red {
+ label = "ch-1:red";
+ gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+ };
+ ch1-green {
+ label = "ch-1:green";
+ gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
+ };
+ ch2-red {
+ label = "ch-2:red";
+ gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
+ };
+ ch2-green {
+ label = "ch-2:green";
+ gpios = <&pioA 20 GPIO_ACTIVE_LOW>;
+ };
+ data-red {
+ label = "data:red";
+ gpios = <&pioA 19 GPIO_ACTIVE_LOW>;
+ };
+ data-green {
+ label = "data:green";
+ gpios = <&pioA 18 GPIO_ACTIVE_LOW>;
+ };
+ alarm-red {
+ label = "alarm:red";
+ gpios = <&pioA 17 GPIO_ACTIVE_LOW>;
+ };
+ alarm-green {
+ label = "alarm:green";
+ gpios = <&pioA 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&nand0 {
+ at91bootstrap at 0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ barebox at 40000 {
+ label = "bootloader";
+ reg = <0x40000 0x60000>;
+ };
+
+ bareboxenv at c0000 {
+ label = "bareboxenv";
+ reg = <0xc0000 0x40000>;
+ };
+
+ bareboxenv2 at 100000 {
+ label = "bareboxenv2";
+ reg = <0x100000 0x40000>;
+ };
+
+ oftree at 180000 {
+ label = "oftree";
+ reg = <0x180000 0x20000>;
+ };
+
+ kernel at 200000 {
+ label = "kernel";
+ reg = <0x200000 0x500000>;
+ };
+
+ rootfs at 800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+
+ ovlfs at 10000000 {
+ label = "ovlfs";
+ reg = <0x10000000 0x10000000>;
+ };
+};
+
+&ssc0 {
+ #sound-dai-cells = <0>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ jc42 at 18 {
+ compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+ reg = <0x18>;
+ };
+
+ dpot: mcp4651-104 at 28 {
+ compatible = "microchip,mcp4651-104";
+ reg = <0x28>;
+ #io-channel-cells = <1>;
+ };
+
+ pcm5142: pcm5142 at 4c {
+ compatible = "ti,pcm5142";
+
+ reg = <0x4c>;
+
+ AVDD-supply = <®_3v3>;
+ DVDD-supply = <®_3v3>;
+ CPVDD-supply = <®_3v3>;
+
+ clocks = <&sck>;
+
+ pll-in = <3>;
+ pll-out = <6>;
+ };
+
+ eeprom at 50 {
+ compatible = "nxp,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+&usart0 {
+ status = "okay";
+
+ atmel,use-dma-rx;
+};
+
+&pwm0 {
+ status = "okay";
+
+ pinctrl-0 = <&pinctrl_pwm0_pwml2_1>;
+ pinctrl-names = "default";
+};
+
+&macb1 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy at 3 {
+ reg = <3>;
+
+ interrupt-parent = <&pioE>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ atmel,vbus-gpio = <&pioC 31 GPIO_ACTIVE_HIGH>;
+};
+
+&usb1 {
+ status = "okay";
+
+ num-ports = <1>;
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ atmel,oc-gpio = <&pioC 15 GPIO_ACTIVE_LOW>;
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v5 2/2] ARM: sama5_defconfig: add support for the Axentia TSE-850 board
@ 2017-01-10 8:08 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-kernel
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Alexandre Belloni,
Jean-Christophe Plagniol-Villard, linux-arm-kernel, devicetree
Signed-off-by: Peter Rosin <peda@axentia.se>
---
arch/arm/configs/sama5_defconfig | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
index aca8625b6fc9..bf5b3a73e38c 100644
--- a/arch/arm/configs/sama5_defconfig
+++ b/arch/arm/configs/sama5_defconfig
@@ -131,7 +131,7 @@ CONFIG_GPIO_SYSFS=y
CONFIG_POWER_SUPPLY=y
CONFIG_BATTERY_ACT8945A=y
CONFIG_POWER_RESET=y
-# CONFIG_HWMON is not set
+CONFIG_SENSORS_JC42=y
CONFIG_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
CONFIG_SAMA5D4_WATCHDOG=y
@@ -142,6 +142,7 @@ CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_ACT8865=y
CONFIG_REGULATOR_ACT8945A=y
+CONFIG_REGULATOR_PWM=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_MEDIA_CAMERA_SUPPORT=y
CONFIG_V4L_PLATFORM_DRIVERS=y
@@ -164,6 +165,7 @@ CONFIG_SND_ATMEL_SOC=y
CONFIG_SND_ATMEL_SOC_WM8904=y
# CONFIG_HID_GENERIC is not set
CONFIG_SND_ATMEL_SOC_PDMIC=y
+CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
CONFIG_USB=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_EHCI_HCD=y
@@ -199,6 +201,9 @@ CONFIG_AT_XDMAC=y
CONFIG_IIO=y
CONFIG_AT91_ADC=y
CONFIG_AT91_SAMA5D2_ADC=y
+CONFIG_ENVELOPE_DETECTOR=y
+CONFIG_DPOT_DAC=y
+CONFIG_MCP4531=y
CONFIG_PWM=y
CONFIG_PWM_ATMEL=y
CONFIG_PWM_ATMEL_HLCDC_PWM=y
--
2.1.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v5 2/2] ARM: sama5_defconfig: add support for the Axentia TSE-850 board
@ 2017-01-10 8:08 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Peter Rosin, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Alexandre Belloni,
Jean-Christophe Plagniol-Villard,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
Signed-off-by: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
---
arch/arm/configs/sama5_defconfig | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
index aca8625b6fc9..bf5b3a73e38c 100644
--- a/arch/arm/configs/sama5_defconfig
+++ b/arch/arm/configs/sama5_defconfig
@@ -131,7 +131,7 @@ CONFIG_GPIO_SYSFS=y
CONFIG_POWER_SUPPLY=y
CONFIG_BATTERY_ACT8945A=y
CONFIG_POWER_RESET=y
-# CONFIG_HWMON is not set
+CONFIG_SENSORS_JC42=y
CONFIG_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
CONFIG_SAMA5D4_WATCHDOG=y
@@ -142,6 +142,7 @@ CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_ACT8865=y
CONFIG_REGULATOR_ACT8945A=y
+CONFIG_REGULATOR_PWM=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_MEDIA_CAMERA_SUPPORT=y
CONFIG_V4L_PLATFORM_DRIVERS=y
@@ -164,6 +165,7 @@ CONFIG_SND_ATMEL_SOC=y
CONFIG_SND_ATMEL_SOC_WM8904=y
# CONFIG_HID_GENERIC is not set
CONFIG_SND_ATMEL_SOC_PDMIC=y
+CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
CONFIG_USB=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_EHCI_HCD=y
@@ -199,6 +201,9 @@ CONFIG_AT_XDMAC=y
CONFIG_IIO=y
CONFIG_AT91_ADC=y
CONFIG_AT91_SAMA5D2_ADC=y
+CONFIG_ENVELOPE_DETECTOR=y
+CONFIG_DPOT_DAC=y
+CONFIG_MCP4531=y
CONFIG_PWM=y
CONFIG_PWM_ATMEL=y
CONFIG_PWM_ATMEL_HLCDC_PWM=y
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH v5 2/2] ARM: sama5_defconfig: add support for the Axentia TSE-850 board
@ 2017-01-10 8:08 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Peter Rosin <peda@axentia.se>
---
arch/arm/configs/sama5_defconfig | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
index aca8625b6fc9..bf5b3a73e38c 100644
--- a/arch/arm/configs/sama5_defconfig
+++ b/arch/arm/configs/sama5_defconfig
@@ -131,7 +131,7 @@ CONFIG_GPIO_SYSFS=y
CONFIG_POWER_SUPPLY=y
CONFIG_BATTERY_ACT8945A=y
CONFIG_POWER_RESET=y
-# CONFIG_HWMON is not set
+CONFIG_SENSORS_JC42=y
CONFIG_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
CONFIG_SAMA5D4_WATCHDOG=y
@@ -142,6 +142,7 @@ CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_ACT8865=y
CONFIG_REGULATOR_ACT8945A=y
+CONFIG_REGULATOR_PWM=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_MEDIA_CAMERA_SUPPORT=y
CONFIG_V4L_PLATFORM_DRIVERS=y
@@ -164,6 +165,7 @@ CONFIG_SND_ATMEL_SOC=y
CONFIG_SND_ATMEL_SOC_WM8904=y
# CONFIG_HID_GENERIC is not set
CONFIG_SND_ATMEL_SOC_PDMIC=y
+CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
CONFIG_USB=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_EHCI_HCD=y
@@ -199,6 +201,9 @@ CONFIG_AT_XDMAC=y
CONFIG_IIO=y
CONFIG_AT91_ADC=y
CONFIG_AT91_SAMA5D2_ADC=y
+CONFIG_ENVELOPE_DETECTOR=y
+CONFIG_DPOT_DAC=y
+CONFIG_MCP4531=y
CONFIG_PWM=y
CONFIG_PWM_ATMEL=y
CONFIG_PWM_ATMEL_HLCDC_PWM=y
--
2.1.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* Re: [PATCH v5 2/2] ARM: sama5_defconfig: add support for the Axentia TSE-850 board
2017-01-10 8:08 ` Peter Rosin
(?)
@ 2017-01-10 9:10 ` Nicolas Ferre
-1 siblings, 0 replies; 26+ messages in thread
From: Nicolas Ferre @ 2017-01-10 9:10 UTC (permalink / raw)
To: Peter Rosin
Cc: linux-kernel, Rob Herring, Mark Rutland, Russell King,
Alexandre Belloni, Jean-Christophe Plagniol-Villard,
linux-arm-kernel, devicetree
Le 10/01/2017 à 09:08, Peter Rosin a écrit :
> Signed-off-by: Peter Rosin <peda@axentia.se>
I know that most of the entries in this configuration file are direct
additions to the kernel but what about moving some of your additions to
modules?
Regards,
> ---
> arch/arm/configs/sama5_defconfig | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
> index aca8625b6fc9..bf5b3a73e38c 100644
> --- a/arch/arm/configs/sama5_defconfig
> +++ b/arch/arm/configs/sama5_defconfig
> @@ -131,7 +131,7 @@ CONFIG_GPIO_SYSFS=y
> CONFIG_POWER_SUPPLY=y
> CONFIG_BATTERY_ACT8945A=y
> CONFIG_POWER_RESET=y
> -# CONFIG_HWMON is not set
> +CONFIG_SENSORS_JC42=y
> CONFIG_WATCHDOG=y
> CONFIG_AT91SAM9X_WATCHDOG=y
> CONFIG_SAMA5D4_WATCHDOG=y
> @@ -142,6 +142,7 @@ CONFIG_REGULATOR=y
> CONFIG_REGULATOR_FIXED_VOLTAGE=y
> CONFIG_REGULATOR_ACT8865=y
> CONFIG_REGULATOR_ACT8945A=y
> +CONFIG_REGULATOR_PWM=y
> CONFIG_MEDIA_SUPPORT=y
> CONFIG_MEDIA_CAMERA_SUPPORT=y
> CONFIG_V4L_PLATFORM_DRIVERS=y
> @@ -164,6 +165,7 @@ CONFIG_SND_ATMEL_SOC=y
> CONFIG_SND_ATMEL_SOC_WM8904=y
> # CONFIG_HID_GENERIC is not set
> CONFIG_SND_ATMEL_SOC_PDMIC=y
> +CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
> CONFIG_USB=y
> CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
> CONFIG_USB_EHCI_HCD=y
> @@ -199,6 +201,9 @@ CONFIG_AT_XDMAC=y
> CONFIG_IIO=y
> CONFIG_AT91_ADC=y
> CONFIG_AT91_SAMA5D2_ADC=y
> +CONFIG_ENVELOPE_DETECTOR=y
> +CONFIG_DPOT_DAC=y
> +CONFIG_MCP4531=y
> CONFIG_PWM=y
> CONFIG_PWM_ATMEL=y
> CONFIG_PWM_ATMEL_HLCDC_PWM=y
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v5 2/2] ARM: sama5_defconfig: add support for the Axentia TSE-850 board
@ 2017-01-10 9:10 ` Nicolas Ferre
0 siblings, 0 replies; 26+ messages in thread
From: Nicolas Ferre @ 2017-01-10 9:10 UTC (permalink / raw)
To: Peter Rosin
Cc: linux-kernel, Rob Herring, Mark Rutland, Russell King,
Alexandre Belloni, Jean-Christophe Plagniol-Villard,
linux-arm-kernel, devicetree
Le 10/01/2017 à 09:08, Peter Rosin a écrit :
> Signed-off-by: Peter Rosin <peda@axentia.se>
I know that most of the entries in this configuration file are direct
additions to the kernel but what about moving some of your additions to
modules?
Regards,
> ---
> arch/arm/configs/sama5_defconfig | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
> index aca8625b6fc9..bf5b3a73e38c 100644
> --- a/arch/arm/configs/sama5_defconfig
> +++ b/arch/arm/configs/sama5_defconfig
> @@ -131,7 +131,7 @@ CONFIG_GPIO_SYSFS=y
> CONFIG_POWER_SUPPLY=y
> CONFIG_BATTERY_ACT8945A=y
> CONFIG_POWER_RESET=y
> -# CONFIG_HWMON is not set
> +CONFIG_SENSORS_JC42=y
> CONFIG_WATCHDOG=y
> CONFIG_AT91SAM9X_WATCHDOG=y
> CONFIG_SAMA5D4_WATCHDOG=y
> @@ -142,6 +142,7 @@ CONFIG_REGULATOR=y
> CONFIG_REGULATOR_FIXED_VOLTAGE=y
> CONFIG_REGULATOR_ACT8865=y
> CONFIG_REGULATOR_ACT8945A=y
> +CONFIG_REGULATOR_PWM=y
> CONFIG_MEDIA_SUPPORT=y
> CONFIG_MEDIA_CAMERA_SUPPORT=y
> CONFIG_V4L_PLATFORM_DRIVERS=y
> @@ -164,6 +165,7 @@ CONFIG_SND_ATMEL_SOC=y
> CONFIG_SND_ATMEL_SOC_WM8904=y
> # CONFIG_HID_GENERIC is not set
> CONFIG_SND_ATMEL_SOC_PDMIC=y
> +CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
> CONFIG_USB=y
> CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
> CONFIG_USB_EHCI_HCD=y
> @@ -199,6 +201,9 @@ CONFIG_AT_XDMAC=y
> CONFIG_IIO=y
> CONFIG_AT91_ADC=y
> CONFIG_AT91_SAMA5D2_ADC=y
> +CONFIG_ENVELOPE_DETECTOR=y
> +CONFIG_DPOT_DAC=y
> +CONFIG_MCP4531=y
> CONFIG_PWM=y
> CONFIG_PWM_ATMEL=y
> CONFIG_PWM_ATMEL_HLCDC_PWM=y
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v5 2/2] ARM: sama5_defconfig: add support for the Axentia TSE-850 board
@ 2017-01-10 9:10 ` Nicolas Ferre
0 siblings, 0 replies; 26+ messages in thread
From: Nicolas Ferre @ 2017-01-10 9:10 UTC (permalink / raw)
To: linux-arm-kernel
Le 10/01/2017 ? 09:08, Peter Rosin a ?crit :
> Signed-off-by: Peter Rosin <peda@axentia.se>
I know that most of the entries in this configuration file are direct
additions to the kernel but what about moving some of your additions to
modules?
Regards,
> ---
> arch/arm/configs/sama5_defconfig | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
> index aca8625b6fc9..bf5b3a73e38c 100644
> --- a/arch/arm/configs/sama5_defconfig
> +++ b/arch/arm/configs/sama5_defconfig
> @@ -131,7 +131,7 @@ CONFIG_GPIO_SYSFS=y
> CONFIG_POWER_SUPPLY=y
> CONFIG_BATTERY_ACT8945A=y
> CONFIG_POWER_RESET=y
> -# CONFIG_HWMON is not set
> +CONFIG_SENSORS_JC42=y
> CONFIG_WATCHDOG=y
> CONFIG_AT91SAM9X_WATCHDOG=y
> CONFIG_SAMA5D4_WATCHDOG=y
> @@ -142,6 +142,7 @@ CONFIG_REGULATOR=y
> CONFIG_REGULATOR_FIXED_VOLTAGE=y
> CONFIG_REGULATOR_ACT8865=y
> CONFIG_REGULATOR_ACT8945A=y
> +CONFIG_REGULATOR_PWM=y
> CONFIG_MEDIA_SUPPORT=y
> CONFIG_MEDIA_CAMERA_SUPPORT=y
> CONFIG_V4L_PLATFORM_DRIVERS=y
> @@ -164,6 +165,7 @@ CONFIG_SND_ATMEL_SOC=y
> CONFIG_SND_ATMEL_SOC_WM8904=y
> # CONFIG_HID_GENERIC is not set
> CONFIG_SND_ATMEL_SOC_PDMIC=y
> +CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
> CONFIG_USB=y
> CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
> CONFIG_USB_EHCI_HCD=y
> @@ -199,6 +201,9 @@ CONFIG_AT_XDMAC=y
> CONFIG_IIO=y
> CONFIG_AT91_ADC=y
> CONFIG_AT91_SAMA5D2_ADC=y
> +CONFIG_ENVELOPE_DETECTOR=y
> +CONFIG_DPOT_DAC=y
> +CONFIG_MCP4531=y
> CONFIG_PWM=y
> CONFIG_PWM_ATMEL=y
> CONFIG_PWM_ATMEL_HLCDC_PWM=y
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 9:29 ` Alexandre Belloni
0 siblings, 0 replies; 26+ messages in thread
From: Alexandre Belloni @ 2017-01-10 9:29 UTC (permalink / raw)
To: Peter Rosin
Cc: linux-kernel, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Jean-Christophe Plagniol-Villard,
linux-arm-kernel, devicetree
Hi,
This needs a commit message, please add one.
On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Peter Rosin <peda@axentia.se>
> ---
> Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
> MAINTAINERS | 8 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
> arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
> 5 files changed, 355 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
> create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
> create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt
> new file mode 100644
> index 000000000000..ea3fb96ae465
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/axentia.txt
> @@ -0,0 +1,19 @@
> +Device tree bindings for Axentia ARM devices
> +============================================
> +
> +Linea CPU module
> +----------------
> +
> +Required root node properties:
> +compatible = "axentia,linea",
> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +and following the rules from atmel-at91.txt for a sama5d31 SoC.
> +
> +
> +TSE-850 v3 board
> +----------------
> +
> +Required root node properties:
> +compatible = "axentia,tse850v3", "axentia,linea",
> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +and following the rules from above for the axentia,linea CPU module.
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 97b78cc5aa51..5c2ea6e9cd7f 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -2346,6 +2346,14 @@ S: Maintained
> F: Documentation/devicetree/bindings/sound/axentia,*
> F: sound/soc/atmel/tse850-pcm5142.c
>
> +AXENTIA ARM DEVICES
> +M: Peter Rosin <peda@axentia.se>
> +L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
> +S: Maintained
> +F: Documentation/devicetree/bindings/arm/axentia.txt
> +F: arch/arm/boot/dts/at91-linea.dtsi
> +F: arch/arm/boot/dts/at91-tse850-3.dts
> +
I don't think you need to add yourself to MAINTAINERS for two DTs if
that is just to keep checkpatch happy, don't bother.
> AZ6007 DVB DRIVERV
> M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
> M: Mauro Carvalho Chehab <mchehab@kernel.org>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 9a7375c388a8..7632849866de 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
> at91-kizbox2.dtb \
> at91-sama5d2_xplained.dtb \
> at91-sama5d3_xplained.dtb \
> + at91-tse850-3.dtb \
> sama5d31ek.dtb \
> sama5d33ek.dtb \
> sama5d34ek.dtb \
> diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/at91-linea.dtsi
> new file mode 100644
> index 000000000000..646feb0daa81
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-linea.dtsi
> @@ -0,0 +1,53 @@
> +/*
> + * at91-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
> + *
> + * Copyright (C) 2017 Axentia Technologies AB
> + *
> + * Author: Peter Rosin <peda@axentia.se>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +#include "sama5d31.dtsi"
> +
> +/ {
> + compatible = "axentia,linea",
> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +
> + memory {
> + reg = <0x20000000 0x4000000>;
> + };
> +};
> +
> +&slow_xtal {
> + clock-frequency = <32768>;
> +};
> +
> +&main_xtal {
> + clock-frequency = <12000000>;
> +};
> +
> +&main {
> + clock-frequency = <12000000>;
> +};
> +
I don't think this is needed
--
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 9:29 ` Alexandre Belloni
0 siblings, 0 replies; 26+ messages in thread
From: Alexandre Belloni @ 2017-01-10 9:29 UTC (permalink / raw)
To: Peter Rosin
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Mark Rutland,
Russell King, Nicolas Ferre, Jean-Christophe Plagniol-Villard,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
Hi,
This needs a commit message, please add one.
On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Signed-off-by: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
> ---
> Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
> MAINTAINERS | 8 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
> arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
> 5 files changed, 355 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
> create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
> create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt
> new file mode 100644
> index 000000000000..ea3fb96ae465
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/axentia.txt
> @@ -0,0 +1,19 @@
> +Device tree bindings for Axentia ARM devices
> +============================================
> +
> +Linea CPU module
> +----------------
> +
> +Required root node properties:
> +compatible = "axentia,linea",
> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +and following the rules from atmel-at91.txt for a sama5d31 SoC.
> +
> +
> +TSE-850 v3 board
> +----------------
> +
> +Required root node properties:
> +compatible = "axentia,tse850v3", "axentia,linea",
> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +and following the rules from above for the axentia,linea CPU module.
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 97b78cc5aa51..5c2ea6e9cd7f 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -2346,6 +2346,14 @@ S: Maintained
> F: Documentation/devicetree/bindings/sound/axentia,*
> F: sound/soc/atmel/tse850-pcm5142.c
>
> +AXENTIA ARM DEVICES
> +M: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
> +L: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org (moderated for non-subscribers)
> +S: Maintained
> +F: Documentation/devicetree/bindings/arm/axentia.txt
> +F: arch/arm/boot/dts/at91-linea.dtsi
> +F: arch/arm/boot/dts/at91-tse850-3.dts
> +
I don't think you need to add yourself to MAINTAINERS for two DTs if
that is just to keep checkpatch happy, don't bother.
> AZ6007 DVB DRIVERV
> M: Mauro Carvalho Chehab <mchehab-JsYNTwtnfakRB7SZvlqPiA@public.gmane.org>
> M: Mauro Carvalho Chehab <mchehab-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 9a7375c388a8..7632849866de 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
> at91-kizbox2.dtb \
> at91-sama5d2_xplained.dtb \
> at91-sama5d3_xplained.dtb \
> + at91-tse850-3.dtb \
> sama5d31ek.dtb \
> sama5d33ek.dtb \
> sama5d34ek.dtb \
> diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/at91-linea.dtsi
> new file mode 100644
> index 000000000000..646feb0daa81
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-linea.dtsi
> @@ -0,0 +1,53 @@
> +/*
> + * at91-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
> + *
> + * Copyright (C) 2017 Axentia Technologies AB
> + *
> + * Author: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +#include "sama5d31.dtsi"
> +
> +/ {
> + compatible = "axentia,linea",
> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +
> + memory {
> + reg = <0x20000000 0x4000000>;
> + };
> +};
> +
> +&slow_xtal {
> + clock-frequency = <32768>;
> +};
> +
> +&main_xtal {
> + clock-frequency = <12000000>;
> +};
> +
> +&main {
> + clock-frequency = <12000000>;
> +};
> +
I don't think this is needed
--
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 9:29 ` Alexandre Belloni
0 siblings, 0 replies; 26+ messages in thread
From: Alexandre Belloni @ 2017-01-10 9:29 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
This needs a commit message, please add one.
On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Peter Rosin <peda@axentia.se>
> ---
> Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
> MAINTAINERS | 8 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
> arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
> 5 files changed, 355 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
> create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
> create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt
> new file mode 100644
> index 000000000000..ea3fb96ae465
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/axentia.txt
> @@ -0,0 +1,19 @@
> +Device tree bindings for Axentia ARM devices
> +============================================
> +
> +Linea CPU module
> +----------------
> +
> +Required root node properties:
> +compatible = "axentia,linea",
> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +and following the rules from atmel-at91.txt for a sama5d31 SoC.
> +
> +
> +TSE-850 v3 board
> +----------------
> +
> +Required root node properties:
> +compatible = "axentia,tse850v3", "axentia,linea",
> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +and following the rules from above for the axentia,linea CPU module.
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 97b78cc5aa51..5c2ea6e9cd7f 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -2346,6 +2346,14 @@ S: Maintained
> F: Documentation/devicetree/bindings/sound/axentia,*
> F: sound/soc/atmel/tse850-pcm5142.c
>
> +AXENTIA ARM DEVICES
> +M: Peter Rosin <peda@axentia.se>
> +L: linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
> +S: Maintained
> +F: Documentation/devicetree/bindings/arm/axentia.txt
> +F: arch/arm/boot/dts/at91-linea.dtsi
> +F: arch/arm/boot/dts/at91-tse850-3.dts
> +
I don't think you need to add yourself to MAINTAINERS for two DTs if
that is just to keep checkpatch happy, don't bother.
> AZ6007 DVB DRIVERV
> M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
> M: Mauro Carvalho Chehab <mchehab@kernel.org>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 9a7375c388a8..7632849866de 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
> at91-kizbox2.dtb \
> at91-sama5d2_xplained.dtb \
> at91-sama5d3_xplained.dtb \
> + at91-tse850-3.dtb \
> sama5d31ek.dtb \
> sama5d33ek.dtb \
> sama5d34ek.dtb \
> diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/at91-linea.dtsi
> new file mode 100644
> index 000000000000..646feb0daa81
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-linea.dtsi
> @@ -0,0 +1,53 @@
> +/*
> + * at91-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
> + *
> + * Copyright (C) 2017 Axentia Technologies AB
> + *
> + * Author: Peter Rosin <peda@axentia.se>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +
> +#include "sama5d31.dtsi"
> +
> +/ {
> + compatible = "axentia,linea",
> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +
> + memory {
> + reg = <0x20000000 0x4000000>;
> + };
> +};
> +
> +&slow_xtal {
> + clock-frequency = <32768>;
> +};
> +
> +&main_xtal {
> + clock-frequency = <12000000>;
> +};
> +
> +&main {
> + clock-frequency = <12000000>;
> +};
> +
I don't think this is needed
--
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 9:52 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 9:52 UTC (permalink / raw)
To: Alexandre Belloni
Cc: linux-kernel, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Jean-Christophe Plagniol-Villard,
linux-arm-kernel, devicetree
On 2017-01-10 10:29, Alexandre Belloni wrote:
> Hi,
>
> This needs a commit message, please add one.
There's not all that much to say, but ok, I'll add something.
> On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
>> Acked-by: Rob Herring <robh@kernel.org>
>> Signed-off-by: Peter Rosin <peda@axentia.se>
>> ---
>> Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
>> MAINTAINERS | 8 +
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
>> arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
>> 5 files changed, 355 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
>> create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
>> create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
>>
>> diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt
>> new file mode 100644
>> index 000000000000..ea3fb96ae465
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/arm/axentia.txt
>> @@ -0,0 +1,19 @@
>> +Device tree bindings for Axentia ARM devices
>> +============================================
>> +
>> +Linea CPU module
>> +----------------
>> +
>> +Required root node properties:
>> +compatible = "axentia,linea",
>> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
>> +and following the rules from atmel-at91.txt for a sama5d31 SoC.
>> +
>> +
>> +TSE-850 v3 board
>> +----------------
>> +
>> +Required root node properties:
>> +compatible = "axentia,tse850v3", "axentia,linea",
>> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
>> +and following the rules from above for the axentia,linea CPU module.
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 97b78cc5aa51..5c2ea6e9cd7f 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -2346,6 +2346,14 @@ S: Maintained
>> F: Documentation/devicetree/bindings/sound/axentia,*
>> F: sound/soc/atmel/tse850-pcm5142.c
>>
>> +AXENTIA ARM DEVICES
>> +M: Peter Rosin <peda@axentia.se>
>> +L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
>> +S: Maintained
>> +F: Documentation/devicetree/bindings/arm/axentia.txt
>> +F: arch/arm/boot/dts/at91-linea.dtsi
>> +F: arch/arm/boot/dts/at91-tse850-3.dts
>> +
>
> I don't think you need to add yourself to MAINTAINERS for two DTs if
> that is just to keep checkpatch happy, don't bother.
There's also the benefit of the increased chances of me getting
notified of changes. I don't mind...
>> AZ6007 DVB DRIVERV
>> M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
>> M: Mauro Carvalho Chehab <mchehab@kernel.org>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 9a7375c388a8..7632849866de 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
>> at91-kizbox2.dtb \
>> at91-sama5d2_xplained.dtb \
>> at91-sama5d3_xplained.dtb \
>> + at91-tse850-3.dtb \
>> sama5d31ek.dtb \
>> sama5d33ek.dtb \
>> sama5d34ek.dtb \
>> diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/at91-linea.dtsi
>> new file mode 100644
>> index 000000000000..646feb0daa81
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91-linea.dtsi
>> @@ -0,0 +1,53 @@
>> +/*
>> + * at91-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
>> + *
>> + * Copyright (C) 2017 Axentia Technologies AB
>> + *
>> + * Author: Peter Rosin <peda@axentia.se>
>> + *
>> + * Licensed under GPLv2 or later.
>> + */
>> +
>> +#include "sama5d31.dtsi"
>> +
>> +/ {
>> + compatible = "axentia,linea",
>> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
>> +
>> + memory {
>> + reg = <0x20000000 0x4000000>;
>> + };
>> +};
>> +
>> +&slow_xtal {
>> + clock-frequency = <32768>;
>> +};
>> +
>> +&main_xtal {
>> + clock-frequency = <12000000>;
>> +};
>> +
>> +&main {
>> + clock-frequency = <12000000>;
>> +};
>> +
>
> I don't think this is needed
>
>
"this"? The &main frequency, or all of them?
Cheers,
peda
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 9:52 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 9:52 UTC (permalink / raw)
To: Alexandre Belloni
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Mark Rutland,
Russell King, Nicolas Ferre, Jean-Christophe Plagniol-Villard,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
On 2017-01-10 10:29, Alexandre Belloni wrote:
> Hi,
>
> This needs a commit message, please add one.
There's not all that much to say, but ok, I'll add something.
> On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
>> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>> Signed-off-by: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
>> ---
>> Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
>> MAINTAINERS | 8 +
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
>> arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
>> 5 files changed, 355 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
>> create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
>> create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
>>
>> diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt
>> new file mode 100644
>> index 000000000000..ea3fb96ae465
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/arm/axentia.txt
>> @@ -0,0 +1,19 @@
>> +Device tree bindings for Axentia ARM devices
>> +============================================
>> +
>> +Linea CPU module
>> +----------------
>> +
>> +Required root node properties:
>> +compatible = "axentia,linea",
>> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
>> +and following the rules from atmel-at91.txt for a sama5d31 SoC.
>> +
>> +
>> +TSE-850 v3 board
>> +----------------
>> +
>> +Required root node properties:
>> +compatible = "axentia,tse850v3", "axentia,linea",
>> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
>> +and following the rules from above for the axentia,linea CPU module.
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 97b78cc5aa51..5c2ea6e9cd7f 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -2346,6 +2346,14 @@ S: Maintained
>> F: Documentation/devicetree/bindings/sound/axentia,*
>> F: sound/soc/atmel/tse850-pcm5142.c
>>
>> +AXENTIA ARM DEVICES
>> +M: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
>> +L: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org (moderated for non-subscribers)
>> +S: Maintained
>> +F: Documentation/devicetree/bindings/arm/axentia.txt
>> +F: arch/arm/boot/dts/at91-linea.dtsi
>> +F: arch/arm/boot/dts/at91-tse850-3.dts
>> +
>
> I don't think you need to add yourself to MAINTAINERS for two DTs if
> that is just to keep checkpatch happy, don't bother.
There's also the benefit of the increased chances of me getting
notified of changes. I don't mind...
>> AZ6007 DVB DRIVERV
>> M: Mauro Carvalho Chehab <mchehab-JsYNTwtnfakRB7SZvlqPiA@public.gmane.org>
>> M: Mauro Carvalho Chehab <mchehab-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 9a7375c388a8..7632849866de 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
>> at91-kizbox2.dtb \
>> at91-sama5d2_xplained.dtb \
>> at91-sama5d3_xplained.dtb \
>> + at91-tse850-3.dtb \
>> sama5d31ek.dtb \
>> sama5d33ek.dtb \
>> sama5d34ek.dtb \
>> diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/at91-linea.dtsi
>> new file mode 100644
>> index 000000000000..646feb0daa81
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91-linea.dtsi
>> @@ -0,0 +1,53 @@
>> +/*
>> + * at91-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
>> + *
>> + * Copyright (C) 2017 Axentia Technologies AB
>> + *
>> + * Author: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
>> + *
>> + * Licensed under GPLv2 or later.
>> + */
>> +
>> +#include "sama5d31.dtsi"
>> +
>> +/ {
>> + compatible = "axentia,linea",
>> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
>> +
>> + memory {
>> + reg = <0x20000000 0x4000000>;
>> + };
>> +};
>> +
>> +&slow_xtal {
>> + clock-frequency = <32768>;
>> +};
>> +
>> +&main_xtal {
>> + clock-frequency = <12000000>;
>> +};
>> +
>> +&main {
>> + clock-frequency = <12000000>;
>> +};
>> +
>
> I don't think this is needed
>
>
"this"? The &main frequency, or all of them?
Cheers,
peda
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 9:52 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 9:52 UTC (permalink / raw)
To: linux-arm-kernel
On 2017-01-10 10:29, Alexandre Belloni wrote:
> Hi,
>
> This needs a commit message, please add one.
There's not all that much to say, but ok, I'll add something.
> On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
>> Acked-by: Rob Herring <robh@kernel.org>
>> Signed-off-by: Peter Rosin <peda@axentia.se>
>> ---
>> Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
>> MAINTAINERS | 8 +
>> arch/arm/boot/dts/Makefile | 1 +
>> arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
>> arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
>> 5 files changed, 355 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
>> create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
>> create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
>>
>> diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt
>> new file mode 100644
>> index 000000000000..ea3fb96ae465
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/arm/axentia.txt
>> @@ -0,0 +1,19 @@
>> +Device tree bindings for Axentia ARM devices
>> +============================================
>> +
>> +Linea CPU module
>> +----------------
>> +
>> +Required root node properties:
>> +compatible = "axentia,linea",
>> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
>> +and following the rules from atmel-at91.txt for a sama5d31 SoC.
>> +
>> +
>> +TSE-850 v3 board
>> +----------------
>> +
>> +Required root node properties:
>> +compatible = "axentia,tse850v3", "axentia,linea",
>> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
>> +and following the rules from above for the axentia,linea CPU module.
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 97b78cc5aa51..5c2ea6e9cd7f 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -2346,6 +2346,14 @@ S: Maintained
>> F: Documentation/devicetree/bindings/sound/axentia,*
>> F: sound/soc/atmel/tse850-pcm5142.c
>>
>> +AXENTIA ARM DEVICES
>> +M: Peter Rosin <peda@axentia.se>
>> +L: linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
>> +S: Maintained
>> +F: Documentation/devicetree/bindings/arm/axentia.txt
>> +F: arch/arm/boot/dts/at91-linea.dtsi
>> +F: arch/arm/boot/dts/at91-tse850-3.dts
>> +
>
> I don't think you need to add yourself to MAINTAINERS for two DTs if
> that is just to keep checkpatch happy, don't bother.
There's also the benefit of the increased chances of me getting
notified of changes. I don't mind...
>> AZ6007 DVB DRIVERV
>> M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
>> M: Mauro Carvalho Chehab <mchehab@kernel.org>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 9a7375c388a8..7632849866de 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
>> at91-kizbox2.dtb \
>> at91-sama5d2_xplained.dtb \
>> at91-sama5d3_xplained.dtb \
>> + at91-tse850-3.dtb \
>> sama5d31ek.dtb \
>> sama5d33ek.dtb \
>> sama5d34ek.dtb \
>> diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/at91-linea.dtsi
>> new file mode 100644
>> index 000000000000..646feb0daa81
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91-linea.dtsi
>> @@ -0,0 +1,53 @@
>> +/*
>> + * at91-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
>> + *
>> + * Copyright (C) 2017 Axentia Technologies AB
>> + *
>> + * Author: Peter Rosin <peda@axentia.se>
>> + *
>> + * Licensed under GPLv2 or later.
>> + */
>> +
>> +#include "sama5d31.dtsi"
>> +
>> +/ {
>> + compatible = "axentia,linea",
>> + "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
>> +
>> + memory {
>> + reg = <0x20000000 0x4000000>;
>> + };
>> +};
>> +
>> +&slow_xtal {
>> + clock-frequency = <32768>;
>> +};
>> +
>> +&main_xtal {
>> + clock-frequency = <12000000>;
>> +};
>> +
>> +&main {
>> + clock-frequency = <12000000>;
>> +};
>> +
>
> I don't think this is needed
>
>
"this"? The &main frequency, or all of them?
Cheers,
peda
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 10:42 ` Alexandre Belloni
0 siblings, 0 replies; 26+ messages in thread
From: Alexandre Belloni @ 2017-01-10 10:42 UTC (permalink / raw)
To: Peter Rosin
Cc: linux-kernel, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Jean-Christophe Plagniol-Villard,
linux-arm-kernel, devicetree
On 10/01/2017 at 10:52:56 +0100, Peter Rosin wrote :
> On 2017-01-10 10:29, Alexandre Belloni wrote:
> > Hi,
> >
> > This needs a commit message, please add one.
>
> There's not all that much to say, but ok, I'll add something.
>
It doesn't have to be long but it has to be present.
> > On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
> There's also the benefit of the increased chances of me getting
> notified of changes. I don't mind...
>
Do you expect changes coming from third parties? I'm fine with it
anyway.
> >> +&main {
> >> + clock-frequency = <12000000>;
> >> +};
> >> +
> >
> > I don't think this is needed
> >
> >
>
> "this"? The &main frequency, or all of them?
>
I meant just main
--
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 10:42 ` Alexandre Belloni
0 siblings, 0 replies; 26+ messages in thread
From: Alexandre Belloni @ 2017-01-10 10:42 UTC (permalink / raw)
To: Peter Rosin
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Mark Rutland,
Russell King, Nicolas Ferre, Jean-Christophe Plagniol-Villard,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
On 10/01/2017 at 10:52:56 +0100, Peter Rosin wrote :
> On 2017-01-10 10:29, Alexandre Belloni wrote:
> > Hi,
> >
> > This needs a commit message, please add one.
>
> There's not all that much to say, but ok, I'll add something.
>
It doesn't have to be long but it has to be present.
> > On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
> There's also the benefit of the increased chances of me getting
> notified of changes. I don't mind...
>
Do you expect changes coming from third parties? I'm fine with it
anyway.
> >> +&main {
> >> + clock-frequency = <12000000>;
> >> +};
> >> +
> >
> > I don't think this is needed
> >
> >
>
> "this"? The &main frequency, or all of them?
>
I meant just main
--
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 10:42 ` Alexandre Belloni
0 siblings, 0 replies; 26+ messages in thread
From: Alexandre Belloni @ 2017-01-10 10:42 UTC (permalink / raw)
To: linux-arm-kernel
On 10/01/2017 at 10:52:56 +0100, Peter Rosin wrote :
> On 2017-01-10 10:29, Alexandre Belloni wrote:
> > Hi,
> >
> > This needs a commit message, please add one.
>
> There's not all that much to say, but ok, I'll add something.
>
It doesn't have to be long but it has to be present.
> > On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
> There's also the benefit of the increased chances of me getting
> notified of changes. I don't mind...
>
Do you expect changes coming from third parties? I'm fine with it
anyway.
> >> +&main {
> >> + clock-frequency = <12000000>;
> >> +};
> >> +
> >
> > I don't think this is needed
> >
> >
>
> "this"? The &main frequency, or all of them?
>
I meant just main
--
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 11:21 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 11:21 UTC (permalink / raw)
To: Alexandre Belloni
Cc: linux-kernel, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Jean-Christophe Plagniol-Villard,
linux-arm-kernel, devicetree
On 2017-01-10 11:42, Alexandre Belloni wrote:
> On 10/01/2017 at 10:52:56 +0100, Peter Rosin wrote :
>> On 2017-01-10 10:29, Alexandre Belloni wrote:
>>> Hi,
>>>
>>> This needs a commit message, please add one.
>>
>> There's not all that much to say, but ok, I'll add something.
>>
>
> It doesn't have to be long but it has to be present.
Does it really? There are quite a few examples to contradict that,
and checkpatch doesn't complain. That's no proof of course...
As I said, I'll add something.
>>> On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
>> There's also the benefit of the increased chances of me getting
>> notified of changes. I don't mind...
>>
>
> Do you expect changes coming from third parties? I'm fine with it
> anyway.
Ok, I'll remember this and blame you for everything :-)
>>>> +&main {
>>>> + clock-frequency = <12000000>;
>>>> +};
>>>> +
>>>
>>> I don't think this is needed
>>>
>>>
>>
>> "this"? The &main frequency, or all of them?
>>
>
> I meant just main
Ok, I'll test with that change and then resend. Thanks!
Cheers,
peda
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 11:21 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 11:21 UTC (permalink / raw)
To: Alexandre Belloni
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA, Rob Herring, Mark Rutland,
Russell King, Nicolas Ferre, Jean-Christophe Plagniol-Villard,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
On 2017-01-10 11:42, Alexandre Belloni wrote:
> On 10/01/2017 at 10:52:56 +0100, Peter Rosin wrote :
>> On 2017-01-10 10:29, Alexandre Belloni wrote:
>>> Hi,
>>>
>>> This needs a commit message, please add one.
>>
>> There's not all that much to say, but ok, I'll add something.
>>
>
> It doesn't have to be long but it has to be present.
Does it really? There are quite a few examples to contradict that,
and checkpatch doesn't complain. That's no proof of course...
As I said, I'll add something.
>>> On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
>> There's also the benefit of the increased chances of me getting
>> notified of changes. I don't mind...
>>
>
> Do you expect changes coming from third parties? I'm fine with it
> anyway.
Ok, I'll remember this and blame you for everything :-)
>>>> +&main {
>>>> + clock-frequency = <12000000>;
>>>> +};
>>>> +
>>>
>>> I don't think this is needed
>>>
>>>
>>
>> "this"? The &main frequency, or all of them?
>>
>
> I meant just main
Ok, I'll test with that change and then resend. Thanks!
Cheers,
peda
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 11:21 ` Peter Rosin
0 siblings, 0 replies; 26+ messages in thread
From: Peter Rosin @ 2017-01-10 11:21 UTC (permalink / raw)
To: linux-arm-kernel
On 2017-01-10 11:42, Alexandre Belloni wrote:
> On 10/01/2017 at 10:52:56 +0100, Peter Rosin wrote :
>> On 2017-01-10 10:29, Alexandre Belloni wrote:
>>> Hi,
>>>
>>> This needs a commit message, please add one.
>>
>> There's not all that much to say, but ok, I'll add something.
>>
>
> It doesn't have to be long but it has to be present.
Does it really? There are quite a few examples to contradict that,
and checkpatch doesn't complain. That's no proof of course...
As I said, I'll add something.
>>> On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
>> There's also the benefit of the increased chances of me getting
>> notified of changes. I don't mind...
>>
>
> Do you expect changes coming from third parties? I'm fine with it
> anyway.
Ok, I'll remember this and blame you for everything :-)
>>>> +&main {
>>>> + clock-frequency = <12000000>;
>>>> +};
>>>> +
>>>
>>> I don't think this is needed
>>>
>>>
>>
>> "this"? The &main frequency, or all of them?
>>
>
> I meant just main
Ok, I'll test with that change and then resend. Thanks!
Cheers,
peda
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
2017-01-10 11:21 ` Peter Rosin
@ 2017-01-10 11:32 ` Alexandre Belloni
-1 siblings, 0 replies; 26+ messages in thread
From: Alexandre Belloni @ 2017-01-10 11:32 UTC (permalink / raw)
To: Peter Rosin
Cc: linux-kernel, Rob Herring, Mark Rutland, Russell King,
Nicolas Ferre, Jean-Christophe Plagniol-Villard,
linux-arm-kernel, devicetree
On 10/01/2017 at 12:21:42 +0100, Peter Rosin wrote :
> On 2017-01-10 11:42, Alexandre Belloni wrote:
> > On 10/01/2017 at 10:52:56 +0100, Peter Rosin wrote :
> >> On 2017-01-10 10:29, Alexandre Belloni wrote:
> >>> Hi,
> >>>
> >>> This needs a commit message, please add one.
> >>
> >> There's not all that much to say, but ok, I'll add something.
> >>
> >
> > It doesn't have to be long but it has to be present.
>
> Does it really? There are quite a few examples to contradict that,
> and checkpatch doesn't complain. That's no proof of course...
>
> As I said, I'll add something.
>
There is public shaming for maintainers taking patches without a commit
message, that's enough for me to require a commit message ;)
https://lwn.net/Articles/560392/
> >>> On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
> >> There's also the benefit of the increased chances of me getting
> >> notified of changes. I don't mind...
> >>
> >
> > Do you expect changes coming from third parties? I'm fine with it
> > anyway.
>
> Ok, I'll remember this and blame you for everything :-)
>
Well, you can let it there, I was just not sure whether you were
expecting to see patches or just trying to make checkpatch happy. As
said, I'm fine with it.
> >>>> +&main {
> >>>> + clock-frequency = <12000000>;
> >>>> +};
> >>>> +
> >>>
> >>> I don't think this is needed
> >>>
> >>>
> >>
> >> "this"? The &main frequency, or all of them?
> >>
> >
> > I meant just main
>
> Ok, I'll test with that change and then resend. Thanks!
>
> Cheers,
> peda
--
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
@ 2017-01-10 11:32 ` Alexandre Belloni
0 siblings, 0 replies; 26+ messages in thread
From: Alexandre Belloni @ 2017-01-10 11:32 UTC (permalink / raw)
To: linux-arm-kernel
On 10/01/2017 at 12:21:42 +0100, Peter Rosin wrote :
> On 2017-01-10 11:42, Alexandre Belloni wrote:
> > On 10/01/2017 at 10:52:56 +0100, Peter Rosin wrote :
> >> On 2017-01-10 10:29, Alexandre Belloni wrote:
> >>> Hi,
> >>>
> >>> This needs a commit message, please add one.
> >>
> >> There's not all that much to say, but ok, I'll add something.
> >>
> >
> > It doesn't have to be long but it has to be present.
>
> Does it really? There are quite a few examples to contradict that,
> and checkpatch doesn't complain. That's no proof of course...
>
> As I said, I'll add something.
>
There is public shaming for maintainers taking patches without a commit
message, that's enough for me to require a commit message ;)
https://lwn.net/Articles/560392/
> >>> On 10/01/2017 at 09:08:51 +0100, Peter Rosin wrote :
> >> There's also the benefit of the increased chances of me getting
> >> notified of changes. I don't mind...
> >>
> >
> > Do you expect changes coming from third parties? I'm fine with it
> > anyway.
>
> Ok, I'll remember this and blame you for everything :-)
>
Well, you can let it there, I was just not sure whether you were
expecting to see patches or just trying to make checkpatch happy. As
said, I'm fine with it.
> >>>> +&main {
> >>>> + clock-frequency = <12000000>;
> >>>> +};
> >>>> +
> >>>
> >>> I don't think this is needed
> >>>
> >>>
> >>
> >> "this"? The &main frequency, or all of them?
> >>
> >
> > I meant just main
>
> Ok, I'll test with that change and then resend. Thanks!
>
> Cheers,
> peda
--
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply [flat|nested] 26+ messages in thread
end of thread, other threads:[~2017-01-10 11:33 UTC | newest]
Thread overview: 26+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-01-10 8:08 [PATCH v5 0/2] Support for Axentia TSE-850 Peter Rosin
2017-01-10 8:08 ` Peter Rosin
2017-01-10 8:08 ` Peter Rosin
2017-01-10 8:08 ` [PATCH v5 1/2] ARM: dts: at91: add devicetree for the " Peter Rosin
2017-01-10 8:08 ` Peter Rosin
2017-01-10 8:08 ` Peter Rosin
2017-01-10 9:29 ` Alexandre Belloni
2017-01-10 9:29 ` Alexandre Belloni
2017-01-10 9:29 ` Alexandre Belloni
2017-01-10 9:52 ` Peter Rosin
2017-01-10 9:52 ` Peter Rosin
2017-01-10 9:52 ` Peter Rosin
2017-01-10 10:42 ` Alexandre Belloni
2017-01-10 10:42 ` Alexandre Belloni
2017-01-10 10:42 ` Alexandre Belloni
2017-01-10 11:21 ` Peter Rosin
2017-01-10 11:21 ` Peter Rosin
2017-01-10 11:21 ` Peter Rosin
2017-01-10 11:32 ` Alexandre Belloni
2017-01-10 11:32 ` Alexandre Belloni
2017-01-10 8:08 ` [PATCH v5 2/2] ARM: sama5_defconfig: add support for the Axentia TSE-850 board Peter Rosin
2017-01-10 8:08 ` Peter Rosin
2017-01-10 8:08 ` Peter Rosin
2017-01-10 9:10 ` Nicolas Ferre
2017-01-10 9:10 ` Nicolas Ferre
2017-01-10 9:10 ` Nicolas Ferre
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.