* [PATCH 1/2] ARM: dts: imx6ul-isiot: Add eMMC node
@ 2017-01-15 21:50 ` Jagan Teki
0 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2017-01-15 21:50 UTC (permalink / raw)
To: Shawn Guo
Cc: linux-arm-kernel, devicetree, linux-kernel, Matteo Lisi,
Michael Trimarchi, Jagan Teki
From: Jagan Teki <jagan@amarulasolutions.com>
Add usdhc2 node, which is eMMC for Engicam Is.IoT MX6UL modules.
dmesg:
-----
mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 M62704 3.53 GiB
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/boot/dts/imx6ul-isiot.dts | 25 +++++++++++++++++++++++++
1 file changed, 25 insertions(+)
diff --git a/arch/arm/boot/dts/imx6ul-isiot.dts b/arch/arm/boot/dts/imx6ul-isiot.dts
index 077bc26..acb97bd 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dts
+++ b/arch/arm/boot/dts/imx6ul-isiot.dts
@@ -76,6 +76,15 @@
status = "okay";
};
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+ bus-width = <8>;
+ no-1-8-v;
+ status = "okay";
+};
+
&iomuxc {
pinctrl_uart1: uart1grp {
fsl,pins = <
@@ -116,4 +125,20 @@
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
>;
};
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17070
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x10070
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17070
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17070
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17070
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17070
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17070
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17070
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17070
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17070
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x17070
+ >;
+ };
};
--
1.9.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 1/2] ARM: dts: imx6ul-isiot: Add eMMC node
@ 2017-01-15 21:50 ` Jagan Teki
0 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2017-01-15 21:50 UTC (permalink / raw)
To: Shawn Guo
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Matteo Lisi,
Michael Trimarchi, Jagan Teki
From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Add usdhc2 node, which is eMMC for Engicam Is.IoT MX6UL modules.
dmesg:
-----
mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 M62704 3.53 GiB
Cc: Matteo Lisi <matteo.lisi-4s7YQHO/iPVBDgjK7y7TUQ@public.gmane.org>
Cc: Michael Trimarchi <michael-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Cc: Signed-off-by: Shawn Guo <shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
---
arch/arm/boot/dts/imx6ul-isiot.dts | 25 +++++++++++++++++++++++++
1 file changed, 25 insertions(+)
diff --git a/arch/arm/boot/dts/imx6ul-isiot.dts b/arch/arm/boot/dts/imx6ul-isiot.dts
index 077bc26..acb97bd 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dts
+++ b/arch/arm/boot/dts/imx6ul-isiot.dts
@@ -76,6 +76,15 @@
status = "okay";
};
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+ bus-width = <8>;
+ no-1-8-v;
+ status = "okay";
+};
+
&iomuxc {
pinctrl_uart1: uart1grp {
fsl,pins = <
@@ -116,4 +125,20 @@
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
>;
};
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17070
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x10070
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17070
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17070
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17070
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17070
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17070
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17070
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17070
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17070
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x17070
+ >;
+ };
};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 1/2] ARM: dts: imx6ul-isiot: Add eMMC node
@ 2017-01-15 21:50 ` Jagan Teki
0 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2017-01-15 21:50 UTC (permalink / raw)
To: linux-arm-kernel
From: Jagan Teki <jagan@amarulasolutions.com>
Add usdhc2 node, which is eMMC for Engicam Is.IoT MX6UL modules.
dmesg:
-----
mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 M62704 3.53 GiB
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/boot/dts/imx6ul-isiot.dts | 25 +++++++++++++++++++++++++
1 file changed, 25 insertions(+)
diff --git a/arch/arm/boot/dts/imx6ul-isiot.dts b/arch/arm/boot/dts/imx6ul-isiot.dts
index 077bc26..acb97bd 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dts
+++ b/arch/arm/boot/dts/imx6ul-isiot.dts
@@ -76,6 +76,15 @@
status = "okay";
};
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+ bus-width = <8>;
+ no-1-8-v;
+ status = "okay";
+};
+
&iomuxc {
pinctrl_uart1: uart1grp {
fsl,pins = <
@@ -116,4 +125,20 @@
MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
>;
};
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17070
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x10070
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17070
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17070
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17070
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17070
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17070
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17070
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17070
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17070
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x17070
+ >;
+ };
};
--
1.9.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 2/2] ARM: dts: imx6qdl: Fix "ERROR: code indent should use tabs where possible"
2017-01-15 21:50 ` Jagan Teki
@ 2017-01-15 21:50 ` Jagan Teki
-1 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2017-01-15 21:50 UTC (permalink / raw)
To: Shawn Guo
Cc: linux-arm-kernel, devicetree, linux-kernel, Matteo Lisi,
Michael Trimarchi, Jagan Teki
From: Jagan Teki <jagan@amarulasolutions.com>
Fixed code indent tabs in respetcive imx6qdl dtsi files and
also add space on imx6qdl-icore-rqs.dtsi on usdhc bus-width nodes.
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 2 +-
arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 2 +-
arch/arm/boot/dts/imx6qdl-gw552x.dtsi | 2 +-
arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 4 ++--
4 files changed, 5 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
index b6078b1..91991d6 100644
--- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
@@ -235,7 +235,7 @@
/* VDD_1P8 (1+R1/R2 = 2.505): GPS/VideoIn/ENET-PHY */
reg_1p8v: sw2 {
- regulator-name = "vdd1p8";
+ regulator-name = "vdd1p8";
regulator-min-microvolt = <1033310>;
regulator-max-microvolt = <2004000>;
lltc,fb-voltage-divider = <301000 200000>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
index 19cf036..a208e7e 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
@@ -227,7 +227,7 @@
/* VDD_1P8 (1+R1/R2 = 2.505): GPS/VideoIn/ENET-PHY */
reg_1p8v: sw2 {
- regulator-name = "vdd1p8";
+ regulator-name = "vdd1p8";
regulator-min-microvolt = <1033310>;
regulator-max-microvolt = <2004000>;
lltc,fb-voltage-divider = <301000 200000>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
index 90200fa..67613dd 100644
--- a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
@@ -162,7 +162,7 @@
/* VDD_1P8 (1+R1/R2 = 2.505): ENET-PHY */
reg_1p8v: sw2 {
- regulator-name = "vdd1p8";
+ regulator-name = "vdd1p8";
regulator-min-microvolt = <1033310>;
regulator-max-microvolt = <2004000>;
lltc,fb-voltage-divider = <301000 200000>;
diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
index d5c3aa8..6e29d8b 100644
--- a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
@@ -223,7 +223,7 @@
pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
vmcc-supply = <®_sd3_vmmc>;
cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
- bus-witdh=<4>;
+ bus-witdh = <4>;
no-1-8-v;
status = "okay";
};
@@ -234,7 +234,7 @@
pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
vmcc-supply = <®_sd4_vmmc>;
- bus-witdh=<8>;
+ bus-witdh = <8>;
no-1-8-v;
non-removable;
status = "okay";
--
1.9.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 2/2] ARM: dts: imx6qdl: Fix "ERROR: code indent should use tabs where possible"
@ 2017-01-15 21:50 ` Jagan Teki
0 siblings, 0 replies; 8+ messages in thread
From: Jagan Teki @ 2017-01-15 21:50 UTC (permalink / raw)
To: linux-arm-kernel
From: Jagan Teki <jagan@amarulasolutions.com>
Fixed code indent tabs in respetcive imx6qdl dtsi files and
also add space on imx6qdl-icore-rqs.dtsi on usdhc bus-width nodes.
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 2 +-
arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 2 +-
arch/arm/boot/dts/imx6qdl-gw552x.dtsi | 2 +-
arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi | 4 ++--
4 files changed, 5 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
index b6078b1..91991d6 100644
--- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
@@ -235,7 +235,7 @@
/* VDD_1P8 (1+R1/R2 = 2.505): GPS/VideoIn/ENET-PHY */
reg_1p8v: sw2 {
- regulator-name = "vdd1p8";
+ regulator-name = "vdd1p8";
regulator-min-microvolt = <1033310>;
regulator-max-microvolt = <2004000>;
lltc,fb-voltage-divider = <301000 200000>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
index 19cf036..a208e7e 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
@@ -227,7 +227,7 @@
/* VDD_1P8 (1+R1/R2 = 2.505): GPS/VideoIn/ENET-PHY */
reg_1p8v: sw2 {
- regulator-name = "vdd1p8";
+ regulator-name = "vdd1p8";
regulator-min-microvolt = <1033310>;
regulator-max-microvolt = <2004000>;
lltc,fb-voltage-divider = <301000 200000>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
index 90200fa..67613dd 100644
--- a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
@@ -162,7 +162,7 @@
/* VDD_1P8 (1+R1/R2 = 2.505): ENET-PHY */
reg_1p8v: sw2 {
- regulator-name = "vdd1p8";
+ regulator-name = "vdd1p8";
regulator-min-microvolt = <1033310>;
regulator-max-microvolt = <2004000>;
lltc,fb-voltage-divider = <301000 200000>;
diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
index d5c3aa8..6e29d8b 100644
--- a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
@@ -223,7 +223,7 @@
pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
vmcc-supply = <®_sd3_vmmc>;
cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
- bus-witdh=<4>;
+ bus-witdh = <4>;
no-1-8-v;
status = "okay";
};
@@ -234,7 +234,7 @@
pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
vmcc-supply = <®_sd4_vmmc>;
- bus-witdh=<8>;
+ bus-witdh = <8>;
no-1-8-v;
non-removable;
status = "okay";
--
1.9.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH 2/2] ARM: dts: imx6qdl: Fix "ERROR: code indent should use tabs where possible"
@ 2017-01-23 9:01 ` Shawn Guo
0 siblings, 0 replies; 8+ messages in thread
From: Shawn Guo @ 2017-01-23 9:01 UTC (permalink / raw)
To: Jagan Teki
Cc: linux-arm-kernel, devicetree, linux-kernel, Matteo Lisi,
Michael Trimarchi, Jagan Teki
On Sun, Jan 15, 2017 at 10:50:12PM +0100, Jagan Teki wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
>
> Fixed code indent tabs in respetcive imx6qdl dtsi files and
s/respetcive/respective
I fixed it up and applied both patches.
Shawn
> also add space on imx6qdl-icore-rqs.dtsi on usdhc bus-width nodes.
>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 2/2] ARM: dts: imx6qdl: Fix "ERROR: code indent should use tabs where possible"
@ 2017-01-23 9:01 ` Shawn Guo
0 siblings, 0 replies; 8+ messages in thread
From: Shawn Guo @ 2017-01-23 9:01 UTC (permalink / raw)
To: Jagan Teki
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Matteo Lisi,
Michael Trimarchi, Jagan Teki
On Sun, Jan 15, 2017 at 10:50:12PM +0100, Jagan Teki wrote:
> From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
>
> Fixed code indent tabs in respetcive imx6qdl dtsi files and
s/respetcive/respective
I fixed it up and applied both patches.
Shawn
> also add space on imx6qdl-icore-rqs.dtsi on usdhc bus-width nodes.
>
> Cc: Shawn Guo <shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Signed-off-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH 2/2] ARM: dts: imx6qdl: Fix "ERROR: code indent should use tabs where possible"
@ 2017-01-23 9:01 ` Shawn Guo
0 siblings, 0 replies; 8+ messages in thread
From: Shawn Guo @ 2017-01-23 9:01 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Jan 15, 2017 at 10:50:12PM +0100, Jagan Teki wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
>
> Fixed code indent tabs in respetcive imx6qdl dtsi files and
s/respetcive/respective
I fixed it up and applied both patches.
Shawn
> also add space on imx6qdl-icore-rqs.dtsi on usdhc bus-width nodes.
>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2017-01-23 9:01 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-01-15 21:50 [PATCH 1/2] ARM: dts: imx6ul-isiot: Add eMMC node Jagan Teki
2017-01-15 21:50 ` Jagan Teki
2017-01-15 21:50 ` Jagan Teki
2017-01-15 21:50 ` [PATCH 2/2] ARM: dts: imx6qdl: Fix "ERROR: code indent should use tabs where possible" Jagan Teki
2017-01-15 21:50 ` Jagan Teki
2017-01-23 9:01 ` Shawn Guo
2017-01-23 9:01 ` Shawn Guo
2017-01-23 9:01 ` Shawn Guo
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.