[PATCH v2 00/13] Move pad retention control to Exynos pin controller driver

[PATCH v2 00/13] Move pad retention control to Exynos pin controller driver

[Marek Szyprowski]

Hello,

This patchset is a follow-up of my work on adding runtime PM support
to Exynos pin controller driver:
http://www.spinics.net/lists/arm-kernel/msg550161.html

Runtime PM support itself needs a bit more discussion, so lets first focus on
the prerequisites.

In case of Exynos pin controller driver it is a pad retention control. In
current code it was handled by machine and PMU code and had no relation to
what pin controller driver does. This patch series moves pad retention
control to pin controller driver. While implementing it, I also did a little
cleanup of both Exynos PMU and pin controller drivers. Exynos PMU driver
now provides a convenient function to get PMU regmap from other Exynos drivers.

Patch #1 provides a new interface to get Exynos PMU regmap, which is used
by the patch #11. Patches 2-10 are additional cleanups to the code I was
modyfying. Patches 10-12 implements the move of retention control and patch #13
is another cleanup, which is possible after removing dependency to platform
PM code.

Patches are based on linux-next from 2017.01.16 with Exynos4415 support
removal patch applied: https://lkml.org/lkml/2017/1/14/137


Changelog:

v2:
- reworked exynos_get_pmu_regmap() function and moved to Exynos PMU driver,
  now it doesn't depend on driver probe order thus doesn't need to defer probing
  of pinctrl driver if PMU has not yet been probed
- collected Acks, minor fixes according to review comments

v1: https://www.spinics.net/lists/arm-kernel/msg554487.html
- removed the need to add PMU phandles to all pin controller nodes, so old DTBs
  are properly supported. This has been achieved by getting PMU regmap from
  the "exynos-pmu" device of fixed name.
- more cleanup in Exynos pin controller driver: added missing entries in DT
  documentation, removed "memory allocation failed" messages and added
  initconst annotations.
- added support for s5pv210.
- reworked retention control code to be simpler and ready for adding Exynos5433
  support.

v0: http://www.spinics.net/lists/arm-kernel/msg550161.html
- initial version
- part of "Runtime PM for Exynos pin controller driver" patchset

Patch summary:

Marek Szyprowski (13):
  soc: samsung: pmu: Provide global function to get PMU regmap
  soc: samsung: pmu: Use of_device_get_match_data helper
  soc: samsung: pmu: Remove messages for failed memory allocation
  pinctrl: samsung: Document Exynos3250 SoC support
  pinctrl: samsung: Remove messages for failed memory allocation
  pinctrl: samsung: Fix samsung_pinctrl_create_functions return value
  pinctrl: samsung: Add missing initconst annotation
  pinctrl: samsung: Remove dead code
  pinctrl: samsung: Use generic of_device_get_match_data helper
  pinctrl: samsung: Add infrastructure for pin-bank retention control
  pinctrl: samsung: Move retention control from mach-exynos to the
    pinctrl driver
  pinctrl: samsung: Move retention control from mach-s5pv210 to the
    pinctrl driver
  pinctrl: samsung: Replace syscore ops with standard platform device
    pm_ops

 .../bindings/pinctrl/samsung-pinctrl.txt           |   1 +
 arch/arm/mach-exynos/suspend.c                     |  64 ------
 arch/arm/mach-s5pv210/pm.c                         |   7 -
 arch/arm/mach-s5pv210/regs-clock.h                 |   4 -
 drivers/pinctrl/samsung/pinctrl-exynos.c           | 232 +++++++++++++++++++--
 drivers/pinctrl/samsung/pinctrl-s3c64xx.c          |  12 +-
 drivers/pinctrl/samsung/pinctrl-samsung.c          | 123 ++++-------
 drivers/pinctrl/samsung/pinctrl-samsung.h          |  42 ++++
 drivers/soc/samsung/exynos-pmu.c                   |  22 +-
 include/linux/soc/samsung/exynos-pmu.h             |   7 +
 10 files changed, 320 insertions(+), 194 deletions(-)

-- 
1.9.1

[PATCH v2 00/13] Move pad retention control to Exynos pin controller driver

[Marek Szyprowski]

Hello,

This patchset is a follow-up of my work on adding runtime PM support
to Exynos pin controller driver:
http://www.spinics.net/lists/arm-kernel/msg550161.html

Runtime PM support itself needs a bit more discussion, so lets first focus on
the prerequisites.

In case of Exynos pin controller driver it is a pad retention control. In
current code it was handled by machine and PMU code and had no relation to
what pin controller driver does. This patch series moves pad retention
control to pin controller driver. While implementing it, I also did a little
cleanup of both Exynos PMU and pin controller drivers. Exynos PMU driver
now provides a convenient function to get PMU regmap from other Exynos drivers.

Patch #1 provides a new interface to get Exynos PMU regmap, which is used
by the patch #11. Patches 2-10 are additional cleanups to the code I was
modyfying. Patches 10-12 implements the move of retention control and patch #13
is another cleanup, which is possible after removing dependency to platform
PM code.

Patches are based on linux-next from 2017.01.16 with Exynos4415 support
removal patch applied: https://lkml.org/lkml/2017/1/14/137


Changelog:

v2:
- reworked exynos_get_pmu_regmap() function and moved to Exynos PMU driver,
  now it doesn't depend on driver probe order thus doesn't need to defer probing
  of pinctrl driver if PMU has not yet been probed
- collected Acks, minor fixes according to review comments

v1: https://www.spinics.net/lists/arm-kernel/msg554487.html
- removed the need to add PMU phandles to all pin controller nodes, so old DTBs
  are properly supported. This has been achieved by getting PMU regmap from
  the "exynos-pmu" device of fixed name.
- more cleanup in Exynos pin controller driver: added missing entries in DT
  documentation, removed "memory allocation failed" messages and added
  initconst annotations.
- added support for s5pv210.
- reworked retention control code to be simpler and ready for adding Exynos5433
  support.

v0: http://www.spinics.net/lists/arm-kernel/msg550161.html
- initial version
- part of "Runtime PM for Exynos pin controller driver" patchset

Patch summary:

Marek Szyprowski (13):
  soc: samsung: pmu: Provide global function to get PMU regmap
  soc: samsung: pmu: Use of_device_get_match_data helper
  soc: samsung: pmu: Remove messages for failed memory allocation
  pinctrl: samsung: Document Exynos3250 SoC support
  pinctrl: samsung: Remove messages for failed memory allocation
  pinctrl: samsung: Fix samsung_pinctrl_create_functions return value
  pinctrl: samsung: Add missing initconst annotation
  pinctrl: samsung: Remove dead code
  pinctrl: samsung: Use generic of_device_get_match_data helper
  pinctrl: samsung: Add infrastructure for pin-bank retention control
  pinctrl: samsung: Move retention control from mach-exynos to the
    pinctrl driver
  pinctrl: samsung: Move retention control from mach-s5pv210 to the
    pinctrl driver
  pinctrl: samsung: Replace syscore ops with standard platform device
    pm_ops

 .../bindings/pinctrl/samsung-pinctrl.txt           |   1 +
 arch/arm/mach-exynos/suspend.c                     |  64 ------
 arch/arm/mach-s5pv210/pm.c                         |   7 -
 arch/arm/mach-s5pv210/regs-clock.h                 |   4 -
 drivers/pinctrl/samsung/pinctrl-exynos.c           | 232 +++++++++++++++++++--
 drivers/pinctrl/samsung/pinctrl-s3c64xx.c          |  12 +-
 drivers/pinctrl/samsung/pinctrl-samsung.c          | 123 ++++-------
 drivers/pinctrl/samsung/pinctrl-samsung.h          |  42 ++++
 drivers/soc/samsung/exynos-pmu.c                   |  22 +-
 include/linux/soc/samsung/exynos-pmu.h             |   7 +
 10 files changed, 320 insertions(+), 194 deletions(-)

-- 
1.9.1

[PATCH v2 01/13] soc: samsung: pmu: Provide global function to get PMU regmap

[Marek Szyprowski]

PMU is something like a SoC wide service, so add a helper function to get
PMU regmap. This will be used by other Exynos device drivers. This way it
can be avoided to model this dependency in device tree (as phandles to PMU
node) for almost every device in the SoC.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 drivers/soc/samsung/exynos-pmu.c       | 11 +++++++++++
 include/linux/soc/samsung/exynos-pmu.h |  7 +++++++
 2 files changed, 18 insertions(+)

diff --git a/drivers/soc/samsung/exynos-pmu.c b/drivers/soc/samsung/exynos-pmu.c
index 0acdfd82e751..5c269bf23210 100644
--- a/drivers/soc/samsung/exynos-pmu.c
+++ b/drivers/soc/samsung/exynos-pmu.c
@@ -11,6 +11,7 @@
 
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/mfd/syscon.h>
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 
@@ -92,6 +93,16 @@ void exynos_sys_powerdown_conf(enum sys_powerdown mode)
 	{ /*sentinel*/ },
 };
 
+struct regmap *exynos_get_pmu_regmap(void)
+{
+	struct device_node *np = of_find_matching_node(NULL,
+						      exynos_pmu_of_device_ids);
+	if (np)
+		return syscon_node_to_regmap(np);
+	return ERR_PTR(-ENODEV);
+}
+EXPORT_SYMBOL_GPL(exynos_get_pmu_regmap);
+
 static int exynos_pmu_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *match;
diff --git a/include/linux/soc/samsung/exynos-pmu.h b/include/linux/soc/samsung/exynos-pmu.h
index e2e9de1acc5b..2a841a474684 100644
--- a/include/linux/soc/samsung/exynos-pmu.h
+++ b/include/linux/soc/samsung/exynos-pmu.h
@@ -12,6 +12,8 @@
 #ifndef __LINUX_SOC_EXYNOS_PMU_H
 #define __LINUX_SOC_EXYNOS_PMU_H
 
+#include <linux/regmap.h>
+
 enum sys_powerdown {
 	SYS_AFTR,
 	SYS_LPA,
@@ -20,5 +22,10 @@ enum sys_powerdown {
 };
 
 extern void exynos_sys_powerdown_conf(enum sys_powerdown mode);
+#ifdef CONFIG_EXYNOS_PMU
+extern struct regmap *exynos_get_pmu_regmap(void);
+#else
+static inline struct regmap *exynos_get_pmu_regmap(void) { return NULL; }
+#endif
 
 #endif /* __LINUX_SOC_EXYNOS_PMU_H */
-- 
1.9.1

[PATCH v2 01/13] soc: samsung: pmu: Provide global function to get PMU regmap

[Marek Szyprowski]

PMU is something like a SoC wide service, so add a helper function to get
PMU regmap. This will be used by other Exynos device drivers. This way it
can be avoided to model this dependency in device tree (as phandles to PMU
node) for almost every device in the SoC.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 drivers/soc/samsung/exynos-pmu.c       | 11 +++++++++++
 include/linux/soc/samsung/exynos-pmu.h |  7 +++++++
 2 files changed, 18 insertions(+)

diff --git a/drivers/soc/samsung/exynos-pmu.c b/drivers/soc/samsung/exynos-pmu.c
index 0acdfd82e751..5c269bf23210 100644
--- a/drivers/soc/samsung/exynos-pmu.c
+++ b/drivers/soc/samsung/exynos-pmu.c
@@ -11,6 +11,7 @@
 
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/mfd/syscon.h>
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 
@@ -92,6 +93,16 @@ void exynos_sys_powerdown_conf(enum sys_powerdown mode)
 	{ /*sentinel*/ },
 };
 
+struct regmap *exynos_get_pmu_regmap(void)
+{
+	struct device_node *np = of_find_matching_node(NULL,
+						      exynos_pmu_of_device_ids);
+	if (np)
+		return syscon_node_to_regmap(np);
+	return ERR_PTR(-ENODEV);
+}
+EXPORT_SYMBOL_GPL(exynos_get_pmu_regmap);
+
 static int exynos_pmu_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *match;
diff --git a/include/linux/soc/samsung/exynos-pmu.h b/include/linux/soc/samsung/exynos-pmu.h
index e2e9de1acc5b..2a841a474684 100644
--- a/include/linux/soc/samsung/exynos-pmu.h
+++ b/include/linux/soc/samsung/exynos-pmu.h
@@ -12,6 +12,8 @@
 #ifndef __LINUX_SOC_EXYNOS_PMU_H
 #define __LINUX_SOC_EXYNOS_PMU_H
 
+#include <linux/regmap.h>
+
 enum sys_powerdown {
 	SYS_AFTR,
 	SYS_LPA,
@@ -20,5 +22,10 @@ enum sys_powerdown {
 };
 
 extern void exynos_sys_powerdown_conf(enum sys_powerdown mode);
+#ifdef CONFIG_EXYNOS_PMU
+extern struct regmap *exynos_get_pmu_regmap(void);
+#else
+static inline struct regmap *exynos_get_pmu_regmap(void) { return NULL; }
+#endif
 
 #endif /* __LINUX_SOC_EXYNOS_PMU_H */
-- 
1.9.1

Re: [PATCH v2 01/13] soc: samsung: pmu: Provide global function to get PMU regmap

[Tomasz Figa]

Hi Marek,

2017-01-17 21:44 GMT+09:00 Marek Szyprowski <m.szyprowski@samsung.com>:
> PMU is something like a SoC wide service, so add a helper function to get
> PMU regmap. This will be used by other Exynos device drivers. This way it
> can be avoided to model this dependency in device tree (as phandles to PMU
> node) for almost every device in the SoC.
>
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> ---
>  drivers/soc/samsung/exynos-pmu.c       | 11 +++++++++++
>  include/linux/soc/samsung/exynos-pmu.h |  7 +++++++
>  2 files changed, 18 insertions(+)
>
> diff --git a/drivers/soc/samsung/exynos-pmu.c b/drivers/soc/samsung/exynos-pmu.c
> index 0acdfd82e751..5c269bf23210 100644
> --- a/drivers/soc/samsung/exynos-pmu.c
> +++ b/drivers/soc/samsung/exynos-pmu.c
> @@ -11,6 +11,7 @@
>
>  #include <linux/of.h>
>  #include <linux/of_address.h>
> +#include <linux/mfd/syscon.h>
>  #include <linux/platform_device.h>
>  #include <linux/delay.h>
>
> @@ -92,6 +93,16 @@ void exynos_sys_powerdown_conf(enum sys_powerdown mode)
>         { /*sentinel*/ },
>  };
>
> +struct regmap *exynos_get_pmu_regmap(void)
> +{
> +       struct device_node *np = of_find_matching_node(NULL,
> +                                                     exynos_pmu_of_device_ids);
> +       if (np)
> +               return syscon_node_to_regmap(np);
> +       return ERR_PTR(-ENODEV);
> +}
> +EXPORT_SYMBOL_GPL(exynos_get_pmu_regmap);
> +
>  static int exynos_pmu_probe(struct platform_device *pdev)
>  {
>         const struct of_device_id *match;
> diff --git a/include/linux/soc/samsung/exynos-pmu.h b/include/linux/soc/samsung/exynos-pmu.h
> index e2e9de1acc5b..2a841a474684 100644
> --- a/include/linux/soc/samsung/exynos-pmu.h
> +++ b/include/linux/soc/samsung/exynos-pmu.h
> @@ -12,6 +12,8 @@
>  #ifndef __LINUX_SOC_EXYNOS_PMU_H
>  #define __LINUX_SOC_EXYNOS_PMU_H
>
> +#include <linux/regmap.h>
> +

nit: It would save some compilation time to just add a forward
declaration of struct regmap here instead, in case of files that
include this header, but don't need regmap functionality.

>  enum sys_powerdown {
>         SYS_AFTR,
>         SYS_LPA,
> @@ -20,5 +22,10 @@ enum sys_powerdown {
>  };
>
>  extern void exynos_sys_powerdown_conf(enum sys_powerdown mode);
> +#ifdef CONFIG_EXYNOS_PMU
> +extern struct regmap *exynos_get_pmu_regmap(void);
> +#else
> +static inline struct regmap *exynos_get_pmu_regmap(void) { return NULL; }

Shouldn't be some ERR_PTR() instead?

Best regards,
Tomasz

[PATCH v2 01/13] soc: samsung: pmu: Provide global function to get PMU regmap

[Tomasz Figa]

Hi Marek,

2017-01-17 21:44 GMT+09:00 Marek Szyprowski <m.szyprowski@samsung.com>:
> PMU is something like a SoC wide service, so add a helper function to get
> PMU regmap. This will be used by other Exynos device drivers. This way it
> can be avoided to model this dependency in device tree (as phandles to PMU
> node) for almost every device in the SoC.
>
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> ---
>  drivers/soc/samsung/exynos-pmu.c       | 11 +++++++++++
>  include/linux/soc/samsung/exynos-pmu.h |  7 +++++++
>  2 files changed, 18 insertions(+)
>
> diff --git a/drivers/soc/samsung/exynos-pmu.c b/drivers/soc/samsung/exynos-pmu.c
> index 0acdfd82e751..5c269bf23210 100644
> --- a/drivers/soc/samsung/exynos-pmu.c
> +++ b/drivers/soc/samsung/exynos-pmu.c
> @@ -11,6 +11,7 @@
>
>  #include <linux/of.h>
>  #include <linux/of_address.h>
> +#include <linux/mfd/syscon.h>
>  #include <linux/platform_device.h>
>  #include <linux/delay.h>
>
> @@ -92,6 +93,16 @@ void exynos_sys_powerdown_conf(enum sys_powerdown mode)
>         { /*sentinel*/ },
>  };
>
> +struct regmap *exynos_get_pmu_regmap(void)
> +{
> +       struct device_node *np = of_find_matching_node(NULL,
> +                                                     exynos_pmu_of_device_ids);
> +       if (np)
> +               return syscon_node_to_regmap(np);
> +       return ERR_PTR(-ENODEV);
> +}
> +EXPORT_SYMBOL_GPL(exynos_get_pmu_regmap);
> +
>  static int exynos_pmu_probe(struct platform_device *pdev)
>  {
>         const struct of_device_id *match;
> diff --git a/include/linux/soc/samsung/exynos-pmu.h b/include/linux/soc/samsung/exynos-pmu.h
> index e2e9de1acc5b..2a841a474684 100644
> --- a/include/linux/soc/samsung/exynos-pmu.h
> +++ b/include/linux/soc/samsung/exynos-pmu.h
> @@ -12,6 +12,8 @@
>  #ifndef __LINUX_SOC_EXYNOS_PMU_H
>  #define __LINUX_SOC_EXYNOS_PMU_H
>
> +#include <linux/regmap.h>
> +

nit: It would save some compilation time to just add a forward
declaration of struct regmap here instead, in case of files that
include this header, but don't need regmap functionality.

>  enum sys_powerdown {
>         SYS_AFTR,
>         SYS_LPA,
> @@ -20,5 +22,10 @@ enum sys_powerdown {
>  };
>
>  extern void exynos_sys_powerdown_conf(enum sys_powerdown mode);
> +#ifdef CONFIG_EXYNOS_PMU
> +extern struct regmap *exynos_get_pmu_regmap(void);
> +#else
> +static inline struct regmap *exynos_get_pmu_regmap(void) { return NULL; }

Shouldn't be some ERR_PTR() instead?

Best regards,
Tomasz

[PATCH v2 02/13] soc: samsung: pmu: Use of_device_get_match_data helper

[Marek Szyprowski]

Replace custom code with generic helper to retrieve driver data.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 drivers/soc/samsung/exynos-pmu.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)

diff --git a/drivers/soc/samsung/exynos-pmu.c b/drivers/soc/samsung/exynos-pmu.c
index 5c269bf23210..1f914e63dcc6 100644
--- a/drivers/soc/samsung/exynos-pmu.c
+++ b/drivers/soc/samsung/exynos-pmu.c
@@ -11,6 +11,7 @@
 
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/mfd/syscon.h>
 #include <linux/platform_device.h>
 #include <linux/delay.h>
@@ -105,7 +106,6 @@ struct regmap *exynos_get_pmu_regmap(void)
 
 static int exynos_pmu_probe(struct platform_device *pdev)
 {
-	const struct of_device_id *match;
 	struct device *dev = &pdev->dev;
 	struct resource *res;
 
@@ -122,10 +122,7 @@ static int exynos_pmu_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 	pmu_context->dev = dev;
-
-	match = of_match_node(exynos_pmu_of_device_ids, dev->of_node);
-
-	pmu_context->pmu_data = match->data;
+	pmu_context->pmu_data = of_device_get_match_data(dev);
 
 	if (pmu_context->pmu_data->pmu_init)
 		pmu_context->pmu_data->pmu_init();
-- 
1.9.1

[PATCH v2 02/13] soc: samsung: pmu: Use of_device_get_match_data helper

[Marek Szyprowski]

Replace custom code with generic helper to retrieve driver data.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 drivers/soc/samsung/exynos-pmu.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)

diff --git a/drivers/soc/samsung/exynos-pmu.c b/drivers/soc/samsung/exynos-pmu.c
index 5c269bf23210..1f914e63dcc6 100644
--- a/drivers/soc/samsung/exynos-pmu.c
+++ b/drivers/soc/samsung/exynos-pmu.c
@@ -11,6 +11,7 @@
 
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/mfd/syscon.h>
 #include <linux/platform_device.h>
 #include <linux/delay.h>
@@ -105,7 +106,6 @@ struct regmap *exynos_get_pmu_regmap(void)
 
 static int exynos_pmu_probe(struct platform_device *pdev)
 {
-	const struct of_device_id *match;
 	struct device *dev = &pdev->dev;
 	struct resource *res;
 
@@ -122,10 +122,7 @@ static int exynos_pmu_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 	pmu_context->dev = dev;
-
-	match = of_match_node(exynos_pmu_of_device_ids, dev->of_node);
-
-	pmu_context->pmu_data = match->data;
+	pmu_context->pmu_data = of_device_get_match_data(dev);
 
 	if (pmu_context->pmu_data->pmu_init)
 		pmu_context->pmu_data->pmu_init();
-- 
1.9.1

[PATCH v2 03/13] soc: samsung: pmu: Remove messages for failed memory allocation

[Marek Szyprowski]

Memory subsystem already prints message about failed memory
allocation, there is no need to do it in the driver.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 drivers/soc/samsung/exynos-pmu.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/soc/samsung/exynos-pmu.c b/drivers/soc/samsung/exynos-pmu.c
index 1f914e63dcc6..813df6e7292d 100644
--- a/drivers/soc/samsung/exynos-pmu.c
+++ b/drivers/soc/samsung/exynos-pmu.c
@@ -117,10 +117,8 @@ static int exynos_pmu_probe(struct platform_device *pdev)
 	pmu_context = devm_kzalloc(&pdev->dev,
 			sizeof(struct exynos_pmu_context),
 			GFP_KERNEL);
-	if (!pmu_context) {
-		dev_err(dev, "Cannot allocate memory.\n");
+	if (!pmu_context)
 		return -ENOMEM;
-	}
 	pmu_context->dev = dev;
 	pmu_context->pmu_data = of_device_get_match_data(dev);
 
-- 
1.9.1

[PATCH v2 03/13] soc: samsung: pmu: Remove messages for failed memory allocation

[Marek Szyprowski]

Memory subsystem already prints message about failed memory
allocation, there is no need to do it in the driver.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 drivers/soc/samsung/exynos-pmu.c | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/drivers/soc/samsung/exynos-pmu.c b/drivers/soc/samsung/exynos-pmu.c
index 1f914e63dcc6..813df6e7292d 100644
--- a/drivers/soc/samsung/exynos-pmu.c
+++ b/drivers/soc/samsung/exynos-pmu.c
@@ -117,10 +117,8 @@ static int exynos_pmu_probe(struct platform_device *pdev)
 	pmu_context = devm_kzalloc(&pdev->dev,
 			sizeof(struct exynos_pmu_context),
 			GFP_KERNEL);
-	if (!pmu_context) {
-		dev_err(dev, "Cannot allocate memory.\n");
+	if (!pmu_context)
 		return -ENOMEM;
-	}
 	pmu_context->dev = dev;
 	pmu_context->pmu_data = of_device_get_match_data(dev);
 
-- 
1.9.1

[PATCH v2 04/13] pinctrl: samsung: Document Exynos3250 SoC support

[Marek Szyprowski]

Add missing compatible id for Exynos3250 SoC to device tree docs.
Exynos pin control driver supports it since commit d97f5b9804bfcdc1
("pinctrl: exynos: Add driver data for Exynos3250").

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
index 1baf19eecabf..5e00a21de2bf 100644
--- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -13,6 +13,7 @@ Required Properties:
   - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller,
   - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller,
   - "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller,
+  - "samsung,exynos3250-pinctrl": for Exynos3250 compatible pin-controller.
   - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller.
   - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller.
   - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller.
-- 
1.9.1

[PATCH v2 04/13] pinctrl: samsung: Document Exynos3250 SoC support

[Marek Szyprowski]

Add missing compatible id for Exynos3250 SoC to device tree docs.
Exynos pin control driver supports it since commit d97f5b9804bfcdc1
("pinctrl: exynos: Add driver data for Exynos3250").

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
index 1baf19eecabf..5e00a21de2bf 100644
--- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -13,6 +13,7 @@ Required Properties:
   - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller,
   - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller,
   - "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller,
+  - "samsung,exynos3250-pinctrl": for Exynos3250 compatible pin-controller.
   - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller.
   - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller.
   - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller.
-- 
1.9.1

[PATCH v2 05/13] pinctrl: samsung: Remove messages for failed memory allocation

[Marek Szyprowski]

Memory subsystem already prints message about failed memory
allocation, there is no need to do it in the drivers.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 drivers/pinctrl/samsung/pinctrl-exynos.c  |  8 ++------
 drivers/pinctrl/samsung/pinctrl-s3c64xx.c | 12 +++---------
 drivers/pinctrl/samsung/pinctrl-samsung.c | 24 ++++++------------------
 3 files changed, 11 insertions(+), 33 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index 24814db251a7..bf753a596209 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -528,10 +528,8 @@ static int exynos_eint_wkup_init(struct samsung_pinctrl_drv_data *d)
 
 		weint_data = devm_kzalloc(dev, bank->nr_pins
 					* sizeof(*weint_data), GFP_KERNEL);
-		if (!weint_data) {
-			dev_err(dev, "could not allocate memory for weint_data\n");
+		if (!weint_data)
 			return -ENOMEM;
-		}
 
 		for (idx = 0; idx < bank->nr_pins; ++idx) {
 			irq = irq_of_parse_and_map(bank->of_node, idx);
@@ -559,10 +557,8 @@ static int exynos_eint_wkup_init(struct samsung_pinctrl_drv_data *d)
 
 	muxed_data = devm_kzalloc(dev, sizeof(*muxed_data)
 		+ muxed_banks*sizeof(struct samsung_pin_bank *), GFP_KERNEL);
-	if (!muxed_data) {
-		dev_err(dev, "could not allocate memory for muxed_data\n");
+	if (!muxed_data)
 		return -ENOMEM;
-	}
 
 	irq_set_chained_handler_and_data(irq, exynos_irq_demux_eint16_31,
 					 muxed_data);
diff --git a/drivers/pinctrl/samsung/pinctrl-s3c64xx.c b/drivers/pinctrl/samsung/pinctrl-s3c64xx.c
index 4c632812ccff..f17890aa6e25 100644
--- a/drivers/pinctrl/samsung/pinctrl-s3c64xx.c
+++ b/drivers/pinctrl/samsung/pinctrl-s3c64xx.c
@@ -489,10 +489,8 @@ static int s3c64xx_eint_gpio_init(struct samsung_pinctrl_drv_data *d)
 
 	data = devm_kzalloc(dev, sizeof(*data)
 			+ nr_domains * sizeof(*data->domains), GFP_KERNEL);
-	if (!data) {
-		dev_err(dev, "failed to allocate handler data\n");
+	if (!data)
 		return -ENOMEM;
-	}
 	data->drvdata = d;
 
 	bank = d->pin_banks;
@@ -715,10 +713,8 @@ static int s3c64xx_eint_eint0_init(struct samsung_pinctrl_drv_data *d)
 		return -ENODEV;
 
 	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
-	if (!data) {
-		dev_err(dev, "could not allocate memory for wkup eint data\n");
+	if (!data)
 		return -ENOMEM;
-	}
 	data->drvdata = d;
 
 	for (i = 0; i < NUM_EINT0_IRQ; ++i) {
@@ -751,10 +747,8 @@ static int s3c64xx_eint_eint0_init(struct samsung_pinctrl_drv_data *d)
 
 		ddata = devm_kzalloc(dev,
 				sizeof(*ddata) + nr_eints, GFP_KERNEL);
-		if (!ddata) {
-			dev_err(dev, "failed to allocate domain data\n");
+		if (!ddata)
 			return -ENOMEM;
-		}
 		ddata->bank = bank;
 
 		bank->irq_domain = irq_domain_add_linear(bank->of_node,
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 3bc925f61b71..b11e67e85460 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -93,10 +93,8 @@ static int reserve_map(struct device *dev, struct pinctrl_map **map,
 		return 0;
 
 	new_map = krealloc(*map, sizeof(*new_map) * new_num, GFP_KERNEL);
-	if (!new_map) {
-		dev_err(dev, "krealloc(map) failed\n");
+	if (!new_map)
 		return -ENOMEM;
-	}
 
 	memset(new_map + old_num, 0, (new_num - old_num) * sizeof(*new_map));
 
@@ -133,10 +131,8 @@ static int add_map_configs(struct device *dev, struct pinctrl_map **map,
 
 	dup_configs = kmemdup(configs, num_configs * sizeof(*dup_configs),
 			      GFP_KERNEL);
-	if (!dup_configs) {
-		dev_err(dev, "kmemdup(configs) failed\n");
+	if (!dup_configs)
 		return -ENOMEM;
-	}
 
 	(*map)[*num_maps].type = PIN_MAP_TYPE_CONFIGS_GROUP;
 	(*map)[*num_maps].data.configs.group_or_pin = group;
@@ -156,10 +152,8 @@ static int add_config(struct device *dev, unsigned long **configs,
 
 	new_configs = krealloc(*configs, sizeof(*new_configs) * new_num,
 			       GFP_KERNEL);
-	if (!new_configs) {
-		dev_err(dev, "krealloc(configs) failed\n");
+	if (!new_configs)
 		return -ENOMEM;
-	}
 
 	new_configs[old_num] = config;
 
@@ -756,10 +750,8 @@ static struct samsung_pmx_func *samsung_pinctrl_create_functions(
 
 	functions = devm_kzalloc(dev, func_cnt * sizeof(*functions),
 					GFP_KERNEL);
-	if (!functions) {
-		dev_err(dev, "failed to allocate memory for function list\n");
+	if (!functions)
 		return ERR_PTR(-EINVAL);
-	}
 	func = functions;
 
 	/*
@@ -850,10 +842,8 @@ static int samsung_pinctrl_register(struct platform_device *pdev,
 
 	pindesc = devm_kzalloc(&pdev->dev, sizeof(*pindesc) *
 			drvdata->nr_pins, GFP_KERNEL);
-	if (!pindesc) {
-		dev_err(&pdev->dev, "mem alloc for pin descriptors failed\n");
+	if (!pindesc)
 		return -ENOMEM;
-	}
 	ctrldesc->pins = pindesc;
 	ctrldesc->npins = drvdata->nr_pins;
 
@@ -867,10 +857,8 @@ static int samsung_pinctrl_register(struct platform_device *pdev,
 	 */
 	pin_names = devm_kzalloc(&pdev->dev, sizeof(char) * PIN_NAME_LENGTH *
 					drvdata->nr_pins, GFP_KERNEL);
-	if (!pin_names) {
-		dev_err(&pdev->dev, "mem alloc for pin names failed\n");
+	if (!pin_names)
 		return -ENOMEM;
-	}
 
 	/* for each pin, the name of the pin is pin-bank name + pin number */
 	for (bank = 0; bank < drvdata->nr_banks; bank++) {
-- 
1.9.1

[PATCH v2 05/13] pinctrl: samsung: Remove messages for failed memory allocation

[Marek Szyprowski]

Memory subsystem already prints message about failed memory
allocation, there is no need to do it in the drivers.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 drivers/pinctrl/samsung/pinctrl-exynos.c  |  8 ++------
 drivers/pinctrl/samsung/pinctrl-s3c64xx.c | 12 +++---------
 drivers/pinctrl/samsung/pinctrl-samsung.c | 24 ++++++------------------
 3 files changed, 11 insertions(+), 33 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index 24814db251a7..bf753a596209 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -528,10 +528,8 @@ static int exynos_eint_wkup_init(struct samsung_pinctrl_drv_data *d)
 
 		weint_data = devm_kzalloc(dev, bank->nr_pins
 					* sizeof(*weint_data), GFP_KERNEL);
-		if (!weint_data) {
-			dev_err(dev, "could not allocate memory for weint_data\n");
+		if (!weint_data)
 			return -ENOMEM;
-		}
 
 		for (idx = 0; idx < bank->nr_pins; ++idx) {
 			irq = irq_of_parse_and_map(bank->of_node, idx);
@@ -559,10 +557,8 @@ static int exynos_eint_wkup_init(struct samsung_pinctrl_drv_data *d)
 
 	muxed_data = devm_kzalloc(dev, sizeof(*muxed_data)
 		+ muxed_banks*sizeof(struct samsung_pin_bank *), GFP_KERNEL);
-	if (!muxed_data) {
-		dev_err(dev, "could not allocate memory for muxed_data\n");
+	if (!muxed_data)
 		return -ENOMEM;
-	}
 
 	irq_set_chained_handler_and_data(irq, exynos_irq_demux_eint16_31,
 					 muxed_data);
diff --git a/drivers/pinctrl/samsung/pinctrl-s3c64xx.c b/drivers/pinctrl/samsung/pinctrl-s3c64xx.c
index 4c632812ccff..f17890aa6e25 100644
--- a/drivers/pinctrl/samsung/pinctrl-s3c64xx.c
+++ b/drivers/pinctrl/samsung/pinctrl-s3c64xx.c
@@ -489,10 +489,8 @@ static int s3c64xx_eint_gpio_init(struct samsung_pinctrl_drv_data *d)
 
 	data = devm_kzalloc(dev, sizeof(*data)
 			+ nr_domains * sizeof(*data->domains), GFP_KERNEL);
-	if (!data) {
-		dev_err(dev, "failed to allocate handler data\n");
+	if (!data)
 		return -ENOMEM;
-	}
 	data->drvdata = d;
 
 	bank = d->pin_banks;
@@ -715,10 +713,8 @@ static int s3c64xx_eint_eint0_init(struct samsung_pinctrl_drv_data *d)
 		return -ENODEV;
 
 	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
-	if (!data) {
-		dev_err(dev, "could not allocate memory for wkup eint data\n");
+	if (!data)
 		return -ENOMEM;
-	}
 	data->drvdata = d;
 
 	for (i = 0; i < NUM_EINT0_IRQ; ++i) {
@@ -751,10 +747,8 @@ static int s3c64xx_eint_eint0_init(struct samsung_pinctrl_drv_data *d)
 
 		ddata = devm_kzalloc(dev,
 				sizeof(*ddata) + nr_eints, GFP_KERNEL);
-		if (!ddata) {
-			dev_err(dev, "failed to allocate domain data\n");
+		if (!ddata)
 			return -ENOMEM;
-		}
 		ddata->bank = bank;
 
 		bank->irq_domain = irq_domain_add_linear(bank->of_node,
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 3bc925f61b71..b11e67e85460 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -93,10 +93,8 @@ static int reserve_map(struct device *dev, struct pinctrl_map **map,
 		return 0;
 
 	new_map = krealloc(*map, sizeof(*new_map) * new_num, GFP_KERNEL);
-	if (!new_map) {
-		dev_err(dev, "krealloc(map) failed\n");
+	if (!new_map)
 		return -ENOMEM;
-	}
 
 	memset(new_map + old_num, 0, (new_num - old_num) * sizeof(*new_map));
 
@@ -133,10 +131,8 @@ static int add_map_configs(struct device *dev, struct pinctrl_map **map,
 
 	dup_configs = kmemdup(configs, num_configs * sizeof(*dup_configs),
 			      GFP_KERNEL);
-	if (!dup_configs) {
-		dev_err(dev, "kmemdup(configs) failed\n");
+	if (!dup_configs)
 		return -ENOMEM;
-	}
 
 	(*map)[*num_maps].type = PIN_MAP_TYPE_CONFIGS_GROUP;
 	(*map)[*num_maps].data.configs.group_or_pin = group;
@@ -156,10 +152,8 @@ static int add_config(struct device *dev, unsigned long **configs,
 
 	new_configs = krealloc(*configs, sizeof(*new_configs) * new_num,
 			       GFP_KERNEL);
-	if (!new_configs) {
-		dev_err(dev, "krealloc(configs) failed\n");
+	if (!new_configs)
 		return -ENOMEM;
-	}
 
 	new_configs[old_num] = config;
 
@@ -756,10 +750,8 @@ static struct samsung_pmx_func *samsung_pinctrl_create_functions(
 
 	functions = devm_kzalloc(dev, func_cnt * sizeof(*functions),
 					GFP_KERNEL);
-	if (!functions) {
-		dev_err(dev, "failed to allocate memory for function list\n");
+	if (!functions)
 		return ERR_PTR(-EINVAL);
-	}
 	func = functions;
 
 	/*
@@ -850,10 +842,8 @@ static int samsung_pinctrl_register(struct platform_device *pdev,
 
 	pindesc = devm_kzalloc(&pdev->dev, sizeof(*pindesc) *
 			drvdata->nr_pins, GFP_KERNEL);
-	if (!pindesc) {
-		dev_err(&pdev->dev, "mem alloc for pin descriptors failed\n");
+	if (!pindesc)
 		return -ENOMEM;
-	}
 	ctrldesc->pins = pindesc;
 	ctrldesc->npins = drvdata->nr_pins;
 
@@ -867,10 +857,8 @@ static int samsung_pinctrl_register(struct platform_device *pdev,
 	 */
 	pin_names = devm_kzalloc(&pdev->dev, sizeof(char) * PIN_NAME_LENGTH *
 					drvdata->nr_pins, GFP_KERNEL);
-	if (!pin_names) {
-		dev_err(&pdev->dev, "mem alloc for pin names failed\n");
+	if (!pin_names)
 		return -ENOMEM;
-	}
 
 	/* for each pin, the name of the pin is pin-bank name + pin number */
 	for (bank = 0; bank < drvdata->nr_banks; bank++) {
-- 
1.9.1

[PATCH v2 06/13] pinctrl: samsung: Fix samsung_pinctrl_create_functions return value

[Marek Szyprowski]

Return proper error code in case of memory allocation failure.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 drivers/pinctrl/samsung/pinctrl-samsung.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index b11e67e85460..10b3fd826231 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -751,7 +751,7 @@ static struct samsung_pmx_func *samsung_pinctrl_create_functions(
 	functions = devm_kzalloc(dev, func_cnt * sizeof(*functions),
 					GFP_KERNEL);
 	if (!functions)
-		return ERR_PTR(-EINVAL);
+		return ERR_PTR(-ENOMEM);
 	func = functions;
 
 	/*
-- 
1.9.1

[PATCH v2 06/13] pinctrl: samsung: Fix samsung_pinctrl_create_functions return value

[Marek Szyprowski]

Return proper error code in case of memory allocation failure.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 drivers/pinctrl/samsung/pinctrl-samsung.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index b11e67e85460..10b3fd826231 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -751,7 +751,7 @@ static struct samsung_pmx_func *samsung_pinctrl_create_functions(
 	functions = devm_kzalloc(dev, func_cnt * sizeof(*functions),
 					GFP_KERNEL);
 	if (!functions)
-		return ERR_PTR(-EINVAL);
+		return ERR_PTR(-ENOMEM);
 	func = functions;
 
 	/*
-- 
1.9.1

Re: [PATCH v2 06/13] pinctrl: samsung: Fix samsung_pinctrl_create_functions return value

[Krzysztof Kozlowski]

On Tue, Jan 17, 2017 at 01:44:37PM +0100, Marek Szyprowski wrote:
> Return proper error code in case of memory allocation failure.
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> ---
>  drivers/pinctrl/samsung/pinctrl-samsung.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 

Thanks for fixing.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>

Best regards,
Krzysztof

[PATCH v2 06/13] pinctrl: samsung: Fix samsung_pinctrl_create_functions return value

[Krzysztof Kozlowski]

On Tue, Jan 17, 2017 at 01:44:37PM +0100, Marek Szyprowski wrote:
> Return proper error code in case of memory allocation failure.
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> ---
>  drivers/pinctrl/samsung/pinctrl-samsung.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 

Thanks for fixing.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>

Best regards,
Krzysztof

[PATCH v2 07/13] pinctrl: samsung: Add missing initconst annotation

[Marek Szyprowski]

Exynos5433 support has been added in parallel to adding initconst
annotation to most of the init data structures, so add those
annotations also to Exynos5433 structures.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 drivers/pinctrl/samsung/pinctrl-exynos.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index bf753a596209..70b94ad10cc1 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -1266,7 +1266,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 };
 
 /* pin banks of exynos5433 pin-controller - ALIVE */
-static const struct samsung_pin_bank_data exynos5433_pin_banks0[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks0[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTW(8, 0x000, "gpa0", 0x00),
 	EXYNOS5433_PIN_BANK_EINTW(8, 0x020, "gpa1", 0x04),
 	EXYNOS5433_PIN_BANK_EINTW(8, 0x040, "gpa2", 0x08),
@@ -1279,28 +1279,28 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 };
 
 /* pin banks of exynos5433 pin-controller - AUD */
-static const struct samsung_pin_bank_data exynos5433_pin_banks1[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks1[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(7, 0x000, "gpz0", 0x00),
 	EXYNOS5433_PIN_BANK_EINTG(4, 0x020, "gpz1", 0x04),
 };
 
 /* pin banks of exynos5433 pin-controller - CPIF */
-static const struct samsung_pin_bank_data exynos5433_pin_banks2[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks2[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(2, 0x000, "gpv6", 0x00),
 };
 
 /* pin banks of exynos5433 pin-controller - eSE */
-static const struct samsung_pin_bank_data exynos5433_pin_banks3[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks3[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(3, 0x000, "gpj2", 0x00),
 };
 
 /* pin banks of exynos5433 pin-controller - FINGER */
-static const struct samsung_pin_bank_data exynos5433_pin_banks4[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks4[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(4, 0x000, "gpd5", 0x00),
 };
 
 /* pin banks of exynos5433 pin-controller - FSYS */
-static const struct samsung_pin_bank_data exynos5433_pin_banks5[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks5[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(6, 0x000, "gph1", 0x00),
 	EXYNOS5433_PIN_BANK_EINTG(7, 0x020, "gpr4", 0x04),
 	EXYNOS5433_PIN_BANK_EINTG(5, 0x040, "gpr0", 0x08),
@@ -1310,17 +1310,17 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 };
 
 /* pin banks of exynos5433 pin-controller - IMEM */
-static const struct samsung_pin_bank_data exynos5433_pin_banks6[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks6[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(8, 0x000, "gpf0", 0x00),
 };
 
 /* pin banks of exynos5433 pin-controller - NFC */
-static const struct samsung_pin_bank_data exynos5433_pin_banks7[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks7[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(3, 0x000, "gpj0", 0x00),
 };
 
 /* pin banks of exynos5433 pin-controller - PERIC */
-static const struct samsung_pin_bank_data exynos5433_pin_banks8[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks8[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(6, 0x000, "gpv7", 0x00),
 	EXYNOS5433_PIN_BANK_EINTG(5, 0x020, "gpb0", 0x04),
 	EXYNOS5433_PIN_BANK_EINTG(8, 0x040, "gpc0", 0x08),
@@ -1341,7 +1341,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 };
 
 /* pin banks of exynos5433 pin-controller - TOUCH */
-static const struct samsung_pin_bank_data exynos5433_pin_banks9[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks9[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(3, 0x000, "gpj1", 0x00),
 };
 
@@ -1349,7 +1349,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
  * Samsung pinctrl driver data for Exynos5433 SoC. Exynos5433 SoC includes
  * ten gpio/pin-mux/pinconfig controllers.
  */
-const struct samsung_pin_ctrl exynos5433_pin_ctrl[] = {
+const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
 	{
 		/* pin-controller instance 0 data */
 		.pin_banks	= exynos5433_pin_banks0,
-- 
1.9.1

[PATCH v2 07/13] pinctrl: samsung: Add missing initconst annotation

[Marek Szyprowski]

Exynos5433 support has been added in parallel to adding initconst
annotation to most of the init data structures, so add those
annotations also to Exynos5433 structures.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 drivers/pinctrl/samsung/pinctrl-exynos.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index bf753a596209..70b94ad10cc1 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -1266,7 +1266,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 };
 
 /* pin banks of exynos5433 pin-controller - ALIVE */
-static const struct samsung_pin_bank_data exynos5433_pin_banks0[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks0[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTW(8, 0x000, "gpa0", 0x00),
 	EXYNOS5433_PIN_BANK_EINTW(8, 0x020, "gpa1", 0x04),
 	EXYNOS5433_PIN_BANK_EINTW(8, 0x040, "gpa2", 0x08),
@@ -1279,28 +1279,28 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 };
 
 /* pin banks of exynos5433 pin-controller - AUD */
-static const struct samsung_pin_bank_data exynos5433_pin_banks1[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks1[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(7, 0x000, "gpz0", 0x00),
 	EXYNOS5433_PIN_BANK_EINTG(4, 0x020, "gpz1", 0x04),
 };
 
 /* pin banks of exynos5433 pin-controller - CPIF */
-static const struct samsung_pin_bank_data exynos5433_pin_banks2[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks2[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(2, 0x000, "gpv6", 0x00),
 };
 
 /* pin banks of exynos5433 pin-controller - eSE */
-static const struct samsung_pin_bank_data exynos5433_pin_banks3[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks3[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(3, 0x000, "gpj2", 0x00),
 };
 
 /* pin banks of exynos5433 pin-controller - FINGER */
-static const struct samsung_pin_bank_data exynos5433_pin_banks4[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks4[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(4, 0x000, "gpd5", 0x00),
 };
 
 /* pin banks of exynos5433 pin-controller - FSYS */
-static const struct samsung_pin_bank_data exynos5433_pin_banks5[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks5[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(6, 0x000, "gph1", 0x00),
 	EXYNOS5433_PIN_BANK_EINTG(7, 0x020, "gpr4", 0x04),
 	EXYNOS5433_PIN_BANK_EINTG(5, 0x040, "gpr0", 0x08),
@@ -1310,17 +1310,17 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 };
 
 /* pin banks of exynos5433 pin-controller - IMEM */
-static const struct samsung_pin_bank_data exynos5433_pin_banks6[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks6[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(8, 0x000, "gpf0", 0x00),
 };
 
 /* pin banks of exynos5433 pin-controller - NFC */
-static const struct samsung_pin_bank_data exynos5433_pin_banks7[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks7[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(3, 0x000, "gpj0", 0x00),
 };
 
 /* pin banks of exynos5433 pin-controller - PERIC */
-static const struct samsung_pin_bank_data exynos5433_pin_banks8[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks8[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(6, 0x000, "gpv7", 0x00),
 	EXYNOS5433_PIN_BANK_EINTG(5, 0x020, "gpb0", 0x04),
 	EXYNOS5433_PIN_BANK_EINTG(8, 0x040, "gpc0", 0x08),
@@ -1341,7 +1341,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 };
 
 /* pin banks of exynos5433 pin-controller - TOUCH */
-static const struct samsung_pin_bank_data exynos5433_pin_banks9[] = {
+static const struct samsung_pin_bank_data exynos5433_pin_banks9[] __initconst = {
 	EXYNOS5433_PIN_BANK_EINTG(3, 0x000, "gpj1", 0x00),
 };
 
@@ -1349,7 +1349,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
  * Samsung pinctrl driver data for Exynos5433 SoC. Exynos5433 SoC includes
  * ten gpio/pin-mux/pinconfig controllers.
  */
-const struct samsung_pin_ctrl exynos5433_pin_ctrl[] = {
+const struct samsung_pin_ctrl exynos5433_pin_ctrl[] __initconst = {
 	{
 		/* pin-controller instance 0 data */
 		.pin_banks	= exynos5433_pin_banks0,
-- 
1.9.1

[PATCH v2 08/13] pinctrl: samsung: Remove dead code

[Marek Szyprowski]

'enable' parameter has been removed a while ago, so all code for handling
it can be simply removed.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
---
 drivers/pinctrl/samsung/pinctrl-samsung.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 10b3fd826231..2803ae57f373 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -350,7 +350,7 @@ static void pin_to_reg_bank(struct samsung_pinctrl_drv_data *drvdata,
 
 /* enable or disable a pinmux function */
 static void samsung_pinmux_setup(struct pinctrl_dev *pctldev, unsigned selector,
-					unsigned group, bool enable)
+					unsigned group)
 {
 	struct samsung_pinctrl_drv_data *drvdata;
 	const struct samsung_pin_bank_type *type;
@@ -380,8 +380,7 @@ static void samsung_pinmux_setup(struct pinctrl_dev *pctldev, unsigned selector,
 
 	data = readl(reg + type->reg_offset[PINCFG_TYPE_FUNC]);
 	data &= ~(mask << shift);
-	if (enable)
-		data |= func->val << shift;
+	data |= func->val << shift;
 	writel(data, reg + type->reg_offset[PINCFG_TYPE_FUNC]);
 
 	spin_unlock_irqrestore(&bank->slock, flags);
@@ -392,7 +391,7 @@ static int samsung_pinmux_set_mux(struct pinctrl_dev *pctldev,
 				  unsigned selector,
 				  unsigned group)
 {
-	samsung_pinmux_setup(pctldev, selector, group, true);
+	samsung_pinmux_setup(pctldev, selector, group);
 	return 0;
 }
 
-- 
1.9.1

[PATCH v2 08/13] pinctrl: samsung: Remove dead code

[Marek Szyprowski]

'enable' parameter has been removed a while ago, so all code for handling
it can be simply removed.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
---
 drivers/pinctrl/samsung/pinctrl-samsung.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 10b3fd826231..2803ae57f373 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -350,7 +350,7 @@ static void pin_to_reg_bank(struct samsung_pinctrl_drv_data *drvdata,
 
 /* enable or disable a pinmux function */
 static void samsung_pinmux_setup(struct pinctrl_dev *pctldev, unsigned selector,
-					unsigned group, bool enable)
+					unsigned group)
 {
 	struct samsung_pinctrl_drv_data *drvdata;
 	const struct samsung_pin_bank_type *type;
@@ -380,8 +380,7 @@ static void samsung_pinmux_setup(struct pinctrl_dev *pctldev, unsigned selector,
 
 	data = readl(reg + type->reg_offset[PINCFG_TYPE_FUNC]);
 	data &= ~(mask << shift);
-	if (enable)
-		data |= func->val << shift;
+	data |= func->val << shift;
 	writel(data, reg + type->reg_offset[PINCFG_TYPE_FUNC]);
 
 	spin_unlock_irqrestore(&bank->slock, flags);
@@ -392,7 +391,7 @@ static int samsung_pinmux_set_mux(struct pinctrl_dev *pctldev,
 				  unsigned selector,
 				  unsigned group)
 {
-	samsung_pinmux_setup(pctldev, selector, group, true);
+	samsung_pinmux_setup(pctldev, selector, group);
 	return 0;
 }
 
-- 
1.9.1

[PATCH v2 09/13] pinctrl: samsung: Use generic of_device_get_match_data helper

[Marek Szyprowski]

Replace custom code with generic helper.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
---
 drivers/pinctrl/samsung/pinctrl-samsung.c | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 2803ae57f373..59f99ea7e65b 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -27,6 +27,7 @@
 #include <linux/err.h>
 #include <linux/gpio.h>
 #include <linux/irqdomain.h>
+#include <linux/of_device.h>
 #include <linux/spinlock.h>
 #include <linux/syscore_ops.h>
 
@@ -955,15 +956,12 @@ static int samsung_gpiolib_unregister(struct platform_device *pdev,
 	return 0;
 }
 
-static const struct of_device_id samsung_pinctrl_dt_match[];
-
 /* retrieve the soc specific data */
 static const struct samsung_pin_ctrl *
 samsung_pinctrl_get_soc_data(struct samsung_pinctrl_drv_data *d,
 			     struct platform_device *pdev)
 {
 	int id;
-	const struct of_device_id *match;
 	struct device_node *node = pdev->dev.of_node;
 	struct device_node *np;
 	const struct samsung_pin_bank_data *bdata;
@@ -978,8 +976,8 @@ static int samsung_gpiolib_unregister(struct platform_device *pdev,
 		dev_err(&pdev->dev, "failed to get alias id\n");
 		return ERR_PTR(-ENOENT);
 	}
-	match = of_match_node(samsung_pinctrl_dt_match, node);
-	ctrl = (struct samsung_pin_ctrl *)match->data + id;
+	ctrl = of_device_get_match_data(&pdev->dev);
+	ctrl += id;
 
 	d->suspend = ctrl->suspend;
 	d->resume = ctrl->resume;
-- 
1.9.1

[PATCH v2 09/13] pinctrl: samsung: Use generic of_device_get_match_data helper

[Marek Szyprowski]

Replace custom code with generic helper.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
---
 drivers/pinctrl/samsung/pinctrl-samsung.c | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 2803ae57f373..59f99ea7e65b 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -27,6 +27,7 @@
 #include <linux/err.h>
 #include <linux/gpio.h>
 #include <linux/irqdomain.h>
+#include <linux/of_device.h>
 #include <linux/spinlock.h>
 #include <linux/syscore_ops.h>
 
@@ -955,15 +956,12 @@ static int samsung_gpiolib_unregister(struct platform_device *pdev,
 	return 0;
 }
 
-static const struct of_device_id samsung_pinctrl_dt_match[];
-
 /* retrieve the soc specific data */
 static const struct samsung_pin_ctrl *
 samsung_pinctrl_get_soc_data(struct samsung_pinctrl_drv_data *d,
 			     struct platform_device *pdev)
 {
 	int id;
-	const struct of_device_id *match;
 	struct device_node *node = pdev->dev.of_node;
 	struct device_node *np;
 	const struct samsung_pin_bank_data *bdata;
@@ -978,8 +976,8 @@ static int samsung_gpiolib_unregister(struct platform_device *pdev,
 		dev_err(&pdev->dev, "failed to get alias id\n");
 		return ERR_PTR(-ENOENT);
 	}
-	match = of_match_node(samsung_pinctrl_dt_match, node);
-	ctrl = (struct samsung_pin_ctrl *)match->data + id;
+	ctrl = of_device_get_match_data(&pdev->dev);
+	ctrl += id;
 
 	d->suspend = ctrl->suspend;
 	d->resume = ctrl->resume;
-- 
1.9.1

Re: [PATCH v2 09/13] pinctrl: samsung: Use generic of_device_get_match_data helper

[Krzysztof Kozlowski]

On Tue, Jan 17, 2017 at 01:44:40PM +0100, Marek Szyprowski wrote:
> Replace custom code with generic helper.
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
> ---
>  drivers/pinctrl/samsung/pinctrl-samsung.c | 8 +++-----
>  1 file changed, 3 insertions(+), 5 deletions(-)
> 

Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>

Best regards,
Krzysztof

[PATCH v2 09/13] pinctrl: samsung: Use generic of_device_get_match_data helper

[Krzysztof Kozlowski]

On Tue, Jan 17, 2017 at 01:44:40PM +0100, Marek Szyprowski wrote:
> Replace custom code with generic helper.
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
> ---
>  drivers/pinctrl/samsung/pinctrl-samsung.c | 8 +++-----
>  1 file changed, 3 insertions(+), 5 deletions(-)
> 

Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>

Best regards,
Krzysztof

[PATCH v2 10/13] pinctrl: samsung: Add infrastructure for pin-bank retention control

[Marek Szyprowski]

Pad retention control after suspend/resume cycle should be done from pin
controller driver instead of PMU (power management unit) driver to avoid
possible ordering and logical dependencies. Till now it worked fine only
because PMU driver registered its sys_ops after pin controller.

This patch adds infrastructure to handle pad retention during pin control
driver resume.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 drivers/pinctrl/samsung/pinctrl-samsung.c | 12 +++++++++
 drivers/pinctrl/samsung/pinctrl-samsung.h | 42 +++++++++++++++++++++++++++++++
 2 files changed, 54 insertions(+)

diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 59f99ea7e65b..021abd7221f8 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -1060,6 +1060,13 @@ static int samsung_pinctrl_probe(struct platform_device *pdev)
 	if (res)
 		drvdata->irq = res->start;
 
+	if (ctrl->retention_data) {
+		drvdata->retention_ctrl = ctrl->retention_data->init(drvdata,
+							  ctrl->retention_data);
+		if (IS_ERR(drvdata->retention_ctrl))
+			return PTR_ERR(drvdata->retention_ctrl);
+	}
+
 	ret = samsung_gpiolib_register(pdev, drvdata);
 	if (ret)
 		return ret;
@@ -1126,6 +1133,8 @@ static void samsung_pinctrl_suspend_dev(
 
 	if (drvdata->suspend)
 		drvdata->suspend(drvdata);
+	if (drvdata->retention_ctrl && drvdata->retention_ctrl->enable)
+		drvdata->retention_ctrl->enable(drvdata);
 }
 
 /**
@@ -1173,6 +1182,9 @@ static void samsung_pinctrl_resume_dev(struct samsung_pinctrl_drv_data *drvdata)
 			if (widths[type])
 				writel(bank->pm_save[type], reg + offs[type]);
 	}
+
+	if (drvdata->retention_ctrl && drvdata->retention_ctrl->disable)
+		drvdata->retention_ctrl->disable(drvdata);
 }
 
 /**
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h
index 6f7ce7539a00..5ebbf4137a06 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.h
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.h
@@ -185,10 +185,48 @@ struct samsung_pin_bank {
 };
 
 /**
+ * struct samsung_retention_data: runtime pin-bank retention control data.
+ * @regs: array of PMU registers to control pad retention.
+ * @nr_regs: number of registers in @regs array.
+ * @value: value to store to registers to turn off retention.
+ * @refcnt: atomic counter if retention control affects more than one bank.
+ * @priv: retention control code private data
+ * @on: platform specific callback to enter retention mode.
+ * @off: platform specific callback to exit retention mode.
+ **/
+struct samsung_retention_ctrl {
+	const u32	*regs;
+	int		nr_regs;
+	u32		value;
+	atomic_t	*refcnt;
+	void		*priv;
+	void		(*enable)(struct samsung_pinctrl_drv_data *);
+	void		(*disable)(struct samsung_pinctrl_drv_data *);
+};
+
+/**
+ * struct samsung_retention_data: represent a pin-bank retention control data.
+ * @regs: array of PMU registers to control pad retention.
+ * @nr_regs: number of registers in @regs array.
+ * @value: value to store to registers to turn off retention.
+ * @refcnt: atomic counter if retention control affects more than one bank.
+ * @init: platform specific callback to initialize retention control.
+ **/
+struct samsung_retention_data {
+	const u32	*regs;
+	int		nr_regs;
+	u32		value;
+	atomic_t	*refcnt;
+	struct samsung_retention_ctrl *(*init)(struct samsung_pinctrl_drv_data *,
+					const struct samsung_retention_data *);
+};
+
+/**
  * struct samsung_pin_ctrl: represent a pin controller.
  * @pin_banks: list of pin banks included in this controller.
  * @nr_banks: number of pin banks.
  * @nr_ext_resources: number of the extra base address for pin banks.
+ * @retention_data: configuration data for retention control.
  * @eint_gpio_init: platform specific callback to setup the external gpio
  *	interrupts for the controller.
  * @eint_wkup_init: platform specific callback to setup the external wakeup
@@ -198,6 +236,7 @@ struct samsung_pin_ctrl {
 	const struct samsung_pin_bank_data *pin_banks;
 	u32		nr_banks;
 	int		nr_ext_resources;
+	const struct samsung_retention_data *retention_data;
 
 	int		(*eint_gpio_init)(struct samsung_pinctrl_drv_data *);
 	int		(*eint_wkup_init)(struct samsung_pinctrl_drv_data *);
@@ -219,6 +258,7 @@ struct samsung_pin_ctrl {
  * @nr_function: number of such pin functions.
  * @pin_base: starting system wide pin number.
  * @nr_pins: number of pins supported by the controller.
+ * @retention_ctrl: retention control runtime data.
  */
 struct samsung_pinctrl_drv_data {
 	struct list_head		node;
@@ -238,6 +278,8 @@ struct samsung_pinctrl_drv_data {
 	unsigned int			pin_base;
 	unsigned int			nr_pins;
 
+	const struct samsung_retention_ctrl *retention_ctrl;
+
 	void (*suspend)(struct samsung_pinctrl_drv_data *);
 	void (*resume)(struct samsung_pinctrl_drv_data *);
 };
-- 
1.9.1

[PATCH v2 10/13] pinctrl: samsung: Add infrastructure for pin-bank retention control

[Marek Szyprowski]

Pad retention control after suspend/resume cycle should be done from pin
controller driver instead of PMU (power management unit) driver to avoid
possible ordering and logical dependencies. Till now it worked fine only
because PMU driver registered its sys_ops after pin controller.

This patch adds infrastructure to handle pad retention during pin control
driver resume.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 drivers/pinctrl/samsung/pinctrl-samsung.c | 12 +++++++++
 drivers/pinctrl/samsung/pinctrl-samsung.h | 42 +++++++++++++++++++++++++++++++
 2 files changed, 54 insertions(+)

diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 59f99ea7e65b..021abd7221f8 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -1060,6 +1060,13 @@ static int samsung_pinctrl_probe(struct platform_device *pdev)
 	if (res)
 		drvdata->irq = res->start;
 
+	if (ctrl->retention_data) {
+		drvdata->retention_ctrl = ctrl->retention_data->init(drvdata,
+							  ctrl->retention_data);
+		if (IS_ERR(drvdata->retention_ctrl))
+			return PTR_ERR(drvdata->retention_ctrl);
+	}
+
 	ret = samsung_gpiolib_register(pdev, drvdata);
 	if (ret)
 		return ret;
@@ -1126,6 +1133,8 @@ static void samsung_pinctrl_suspend_dev(
 
 	if (drvdata->suspend)
 		drvdata->suspend(drvdata);
+	if (drvdata->retention_ctrl && drvdata->retention_ctrl->enable)
+		drvdata->retention_ctrl->enable(drvdata);
 }
 
 /**
@@ -1173,6 +1182,9 @@ static void samsung_pinctrl_resume_dev(struct samsung_pinctrl_drv_data *drvdata)
 			if (widths[type])
 				writel(bank->pm_save[type], reg + offs[type]);
 	}
+
+	if (drvdata->retention_ctrl && drvdata->retention_ctrl->disable)
+		drvdata->retention_ctrl->disable(drvdata);
 }
 
 /**
diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h
index 6f7ce7539a00..5ebbf4137a06 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.h
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.h
@@ -185,10 +185,48 @@ struct samsung_pin_bank {
 };
 
 /**
+ * struct samsung_retention_data: runtime pin-bank retention control data.
+ * @regs: array of PMU registers to control pad retention.
+ * @nr_regs: number of registers in @regs array.
+ * @value: value to store to registers to turn off retention.
+ * @refcnt: atomic counter if retention control affects more than one bank.
+ * @priv: retention control code private data
+ * @on: platform specific callback to enter retention mode.
+ * @off: platform specific callback to exit retention mode.
+ **/
+struct samsung_retention_ctrl {
+	const u32	*regs;
+	int		nr_regs;
+	u32		value;
+	atomic_t	*refcnt;
+	void		*priv;
+	void		(*enable)(struct samsung_pinctrl_drv_data *);
+	void		(*disable)(struct samsung_pinctrl_drv_data *);
+};
+
+/**
+ * struct samsung_retention_data: represent a pin-bank retention control data.
+ * @regs: array of PMU registers to control pad retention.
+ * @nr_regs: number of registers in @regs array.
+ * @value: value to store to registers to turn off retention.
+ * @refcnt: atomic counter if retention control affects more than one bank.
+ * @init: platform specific callback to initialize retention control.
+ **/
+struct samsung_retention_data {
+	const u32	*regs;
+	int		nr_regs;
+	u32		value;
+	atomic_t	*refcnt;
+	struct samsung_retention_ctrl *(*init)(struct samsung_pinctrl_drv_data *,
+					const struct samsung_retention_data *);
+};
+
+/**
  * struct samsung_pin_ctrl: represent a pin controller.
  * @pin_banks: list of pin banks included in this controller.
  * @nr_banks: number of pin banks.
  * @nr_ext_resources: number of the extra base address for pin banks.
+ * @retention_data: configuration data for retention control.
  * @eint_gpio_init: platform specific callback to setup the external gpio
  *	interrupts for the controller.
  * @eint_wkup_init: platform specific callback to setup the external wakeup
@@ -198,6 +236,7 @@ struct samsung_pin_ctrl {
 	const struct samsung_pin_bank_data *pin_banks;
 	u32		nr_banks;
 	int		nr_ext_resources;
+	const struct samsung_retention_data *retention_data;
 
 	int		(*eint_gpio_init)(struct samsung_pinctrl_drv_data *);
 	int		(*eint_wkup_init)(struct samsung_pinctrl_drv_data *);
@@ -219,6 +258,7 @@ struct samsung_pin_ctrl {
  * @nr_function: number of such pin functions.
  * @pin_base: starting system wide pin number.
  * @nr_pins: number of pins supported by the controller.
+ * @retention_ctrl: retention control runtime data.
  */
 struct samsung_pinctrl_drv_data {
 	struct list_head		node;
@@ -238,6 +278,8 @@ struct samsung_pinctrl_drv_data {
 	unsigned int			pin_base;
 	unsigned int			nr_pins;
 
+	const struct samsung_retention_ctrl *retention_ctrl;
+
 	void (*suspend)(struct samsung_pinctrl_drv_data *);
 	void (*resume)(struct samsung_pinctrl_drv_data *);
 };
-- 
1.9.1

Re: [PATCH v2 10/13] pinctrl: samsung: Add infrastructure for pin-bank retention control

[Tomasz Figa]

Hi Marek,

2017-01-17 21:44 GMT+09:00 Marek Szyprowski <m.szyprowski@samsung.com>:
> Pad retention control after suspend/resume cycle should be done from pin
> controller driver instead of PMU (power management unit) driver to avoid
> possible ordering and logical dependencies. Till now it worked fine only
> because PMU driver registered its sys_ops after pin controller.
>
> This patch adds infrastructure to handle pad retention during pin control
> driver resume.
>
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
> ---
>  drivers/pinctrl/samsung/pinctrl-samsung.c | 12 +++++++++
>  drivers/pinctrl/samsung/pinctrl-samsung.h | 42 +++++++++++++++++++++++++++++++
>  2 files changed, 54 insertions(+)
>
> diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
> index 59f99ea7e65b..021abd7221f8 100644
> --- a/drivers/pinctrl/samsung/pinctrl-samsung.c
> +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
> @@ -1060,6 +1060,13 @@ static int samsung_pinctrl_probe(struct platform_device *pdev)
>         if (res)
>                 drvdata->irq = res->start;
>
> +       if (ctrl->retention_data) {
> +               drvdata->retention_ctrl = ctrl->retention_data->init(drvdata,
> +                                                         ctrl->retention_data);
> +               if (IS_ERR(drvdata->retention_ctrl))
> +                       return PTR_ERR(drvdata->retention_ctrl);
> +       }
> +
>         ret = samsung_gpiolib_register(pdev, drvdata);
>         if (ret)
>                 return ret;
> @@ -1126,6 +1133,8 @@ static void samsung_pinctrl_suspend_dev(
>
>         if (drvdata->suspend)
>                 drvdata->suspend(drvdata);
> +       if (drvdata->retention_ctrl && drvdata->retention_ctrl->enable)
> +               drvdata->retention_ctrl->enable(drvdata);

Do we need to check presence of ->enable? I think it doesn't make much
sense to provide retention_ctrl with NULL enable or disable.

>  }
>
>  /**
> @@ -1173,6 +1182,9 @@ static void samsung_pinctrl_resume_dev(struct samsung_pinctrl_drv_data *drvdata)
>                         if (widths[type])
>                                 writel(bank->pm_save[type], reg + offs[type]);
>         }
> +
> +       if (drvdata->retention_ctrl && drvdata->retention_ctrl->disable)
> +               drvdata->retention_ctrl->disable(drvdata);

Ditto.

>  }
>
>  /**
> diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h
> index 6f7ce7539a00..5ebbf4137a06 100644
> --- a/drivers/pinctrl/samsung/pinctrl-samsung.h
> +++ b/drivers/pinctrl/samsung/pinctrl-samsung.h
> @@ -185,10 +185,48 @@ struct samsung_pin_bank {
>  };
>
>  /**
> + * struct samsung_retention_data: runtime pin-bank retention control data.
> + * @regs: array of PMU registers to control pad retention.
> + * @nr_regs: number of registers in @regs array.
> + * @value: value to store to registers to turn off retention.
> + * @refcnt: atomic counter if retention control affects more than one bank.
> + * @priv: retention control code private data
> + * @on: platform specific callback to enter retention mode.
> + * @off: platform specific callback to exit retention mode.

s/on/enable/ and s/off/disable/ in comments too. Thanks for taking my
bikeshedding into account, though. :)

> + **/
> +struct samsung_retention_ctrl {
> +       const u32       *regs;
> +       int             nr_regs;
> +       u32             value;
> +       atomic_t        *refcnt;
> +       void            *priv;
> +       void            (*enable)(struct samsung_pinctrl_drv_data *);
> +       void            (*disable)(struct samsung_pinctrl_drv_data *);

^^

Best regards,
Tomasz

[PATCH v2 10/13] pinctrl: samsung: Add infrastructure for pin-bank retention control

[Tomasz Figa]

Hi Marek,

2017-01-17 21:44 GMT+09:00 Marek Szyprowski <m.szyprowski@samsung.com>:
> Pad retention control after suspend/resume cycle should be done from pin
> controller driver instead of PMU (power management unit) driver to avoid
> possible ordering and logical dependencies. Till now it worked fine only
> because PMU driver registered its sys_ops after pin controller.
>
> This patch adds infrastructure to handle pad retention during pin control
> driver resume.
>
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
> ---
>  drivers/pinctrl/samsung/pinctrl-samsung.c | 12 +++++++++
>  drivers/pinctrl/samsung/pinctrl-samsung.h | 42 +++++++++++++++++++++++++++++++
>  2 files changed, 54 insertions(+)
>
> diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
> index 59f99ea7e65b..021abd7221f8 100644
> --- a/drivers/pinctrl/samsung/pinctrl-samsung.c
> +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
> @@ -1060,6 +1060,13 @@ static int samsung_pinctrl_probe(struct platform_device *pdev)
>         if (res)
>                 drvdata->irq = res->start;
>
> +       if (ctrl->retention_data) {
> +               drvdata->retention_ctrl = ctrl->retention_data->init(drvdata,
> +                                                         ctrl->retention_data);
> +               if (IS_ERR(drvdata->retention_ctrl))
> +                       return PTR_ERR(drvdata->retention_ctrl);
> +       }
> +
>         ret = samsung_gpiolib_register(pdev, drvdata);
>         if (ret)
>                 return ret;
> @@ -1126,6 +1133,8 @@ static void samsung_pinctrl_suspend_dev(
>
>         if (drvdata->suspend)
>                 drvdata->suspend(drvdata);
> +       if (drvdata->retention_ctrl && drvdata->retention_ctrl->enable)
> +               drvdata->retention_ctrl->enable(drvdata);

Do we need to check presence of ->enable? I think it doesn't make much
sense to provide retention_ctrl with NULL enable or disable.

>  }
>
>  /**
> @@ -1173,6 +1182,9 @@ static void samsung_pinctrl_resume_dev(struct samsung_pinctrl_drv_data *drvdata)
>                         if (widths[type])
>                                 writel(bank->pm_save[type], reg + offs[type]);
>         }
> +
> +       if (drvdata->retention_ctrl && drvdata->retention_ctrl->disable)
> +               drvdata->retention_ctrl->disable(drvdata);

Ditto.

>  }
>
>  /**
> diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h
> index 6f7ce7539a00..5ebbf4137a06 100644
> --- a/drivers/pinctrl/samsung/pinctrl-samsung.h
> +++ b/drivers/pinctrl/samsung/pinctrl-samsung.h
> @@ -185,10 +185,48 @@ struct samsung_pin_bank {
>  };
>
>  /**
> + * struct samsung_retention_data: runtime pin-bank retention control data.
> + * @regs: array of PMU registers to control pad retention.
> + * @nr_regs: number of registers in @regs array.
> + * @value: value to store to registers to turn off retention.
> + * @refcnt: atomic counter if retention control affects more than one bank.
> + * @priv: retention control code private data
> + * @on: platform specific callback to enter retention mode.
> + * @off: platform specific callback to exit retention mode.

s/on/enable/ and s/off/disable/ in comments too. Thanks for taking my
bikeshedding into account, though. :)

> + **/
> +struct samsung_retention_ctrl {
> +       const u32       *regs;
> +       int             nr_regs;
> +       u32             value;
> +       atomic_t        *refcnt;
> +       void            *priv;
> +       void            (*enable)(struct samsung_pinctrl_drv_data *);
> +       void            (*disable)(struct samsung_pinctrl_drv_data *);

^^

Best regards,
Tomasz

[PATCH v2 11/13] pinctrl: samsung: Move retention control from mach-exynos to the pinctrl driver

[Marek Szyprowski]

This patch moves pad retention control from PMU driver to Exynos pin
controller driver. This helps to avoid possible ordering and logical
dependencies between machine, PMU and pin control code. Till now it
worked fine only because sys_ops for PMU and pin controller were called
in registration order.
This is also a preparation for adding new features to Exynos pin
controller driver, like runtime power management and suspending
individual pin controllers, which might be a part of some power domain.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 arch/arm/mach-exynos/suspend.c           |  64 --------------
 drivers/pinctrl/samsung/pinctrl-exynos.c | 146 +++++++++++++++++++++++++++++++
 2 files changed, 146 insertions(+), 64 deletions(-)

diff --git a/arch/arm/mach-exynos/suspend.c b/arch/arm/mach-exynos/suspend.c
index 25e7c5326259..312d3a886e92 100644
--- a/arch/arm/mach-exynos/suspend.c
+++ b/arch/arm/mach-exynos/suspend.c
@@ -57,7 +57,6 @@ struct exynos_wkup_irq {
 struct exynos_pm_data {
 	const struct exynos_wkup_irq *wkup_irq;
 	unsigned int wake_disable_mask;
-	const unsigned int *release_ret_regs;
 
 	void (*pm_prepare)(void);
 	void (*pm_resume_prepare)(void);
@@ -95,47 +94,6 @@ struct exynos_pm_data {
 	{ /* sentinel */ },
 };
 
-static const unsigned int exynos_release_ret_regs[] = {
-	S5P_PAD_RET_MAUDIO_OPTION,
-	S5P_PAD_RET_GPIO_OPTION,
-	S5P_PAD_RET_UART_OPTION,
-	S5P_PAD_RET_MMCA_OPTION,
-	S5P_PAD_RET_MMCB_OPTION,
-	S5P_PAD_RET_EBIA_OPTION,
-	S5P_PAD_RET_EBIB_OPTION,
-	REG_TABLE_END,
-};
-
-static const unsigned int exynos3250_release_ret_regs[] = {
-	S5P_PAD_RET_MAUDIO_OPTION,
-	S5P_PAD_RET_GPIO_OPTION,
-	S5P_PAD_RET_UART_OPTION,
-	S5P_PAD_RET_MMCA_OPTION,
-	S5P_PAD_RET_MMCB_OPTION,
-	S5P_PAD_RET_EBIA_OPTION,
-	S5P_PAD_RET_EBIB_OPTION,
-	S5P_PAD_RET_MMC2_OPTION,
-	S5P_PAD_RET_SPI_OPTION,
-	REG_TABLE_END,
-};
-
-static const unsigned int exynos5420_release_ret_regs[] = {
-	EXYNOS_PAD_RET_DRAM_OPTION,
-	EXYNOS_PAD_RET_MAUDIO_OPTION,
-	EXYNOS_PAD_RET_JTAG_OPTION,
-	EXYNOS5420_PAD_RET_GPIO_OPTION,
-	EXYNOS5420_PAD_RET_UART_OPTION,
-	EXYNOS5420_PAD_RET_MMCA_OPTION,
-	EXYNOS5420_PAD_RET_MMCB_OPTION,
-	EXYNOS5420_PAD_RET_MMCC_OPTION,
-	EXYNOS5420_PAD_RET_HSI_OPTION,
-	EXYNOS_PAD_RET_EBIA_OPTION,
-	EXYNOS_PAD_RET_EBIB_OPTION,
-	EXYNOS5420_PAD_RET_SPI_OPTION,
-	EXYNOS5420_PAD_RET_DRAM_COREBLK_OPTION,
-	REG_TABLE_END,
-};
-
 static int exynos_irq_set_wake(struct irq_data *data, unsigned int state)
 {
 	const struct exynos_wkup_irq *wkup_irq;
@@ -441,15 +399,6 @@ static int exynos5420_pm_suspend(void)
 	return 0;
 }
 
-static void exynos_pm_release_retention(void)
-{
-	unsigned int i;
-
-	for (i = 0; (pm_data->release_ret_regs[i] != REG_TABLE_END); i++)
-		pmu_raw_writel(EXYNOS_WAKEUP_FROM_LOWPWR,
-				pm_data->release_ret_regs[i]);
-}
-
 static void exynos_pm_resume(void)
 {
 	u32 cpuid = read_cpuid_part();
@@ -457,9 +406,6 @@ static void exynos_pm_resume(void)
 	if (exynos_pm_central_resume())
 		goto early_wakeup;
 
-	/* For release retention */
-	exynos_pm_release_retention();
-
 	if (cpuid == ARM_CPU_PART_CORTEX_A9)
 		scu_enable(S5P_VA_SCU);
 
@@ -481,9 +427,6 @@ static void exynos3250_pm_resume(void)
 	if (exynos_pm_central_resume())
 		goto early_wakeup;
 
-	/* For release retention */
-	exynos_pm_release_retention();
-
 	pmu_raw_writel(S5P_USE_STANDBY_WFI_ALL, S5P_CENTRAL_SEQ_OPTION);
 
 	if (call_firmware_op(resume) == -ENOSYS
@@ -521,9 +464,6 @@ static void exynos5420_pm_resume(void)
 	if (exynos_pm_central_resume())
 		goto early_wakeup;
 
-	/* For release retention */
-	exynos_pm_release_retention();
-
 	pmu_raw_writel(exynos_pmu_spare3, S5P_PMU_SPARE3);
 
 early_wakeup:
@@ -636,7 +576,6 @@ static void exynos_suspend_finish(void)
 static const struct exynos_pm_data exynos3250_pm_data = {
 	.wkup_irq	= exynos3250_wkup_irq,
 	.wake_disable_mask = ((0xFF << 8) | (0x1F << 1)),
-	.release_ret_regs = exynos3250_release_ret_regs,
 	.pm_suspend	= exynos_pm_suspend,
 	.pm_resume	= exynos3250_pm_resume,
 	.pm_prepare	= exynos3250_pm_prepare,
@@ -646,7 +585,6 @@ static void exynos_suspend_finish(void)
 static const struct exynos_pm_data exynos4_pm_data = {
 	.wkup_irq	= exynos4_wkup_irq,
 	.wake_disable_mask = ((0xFF << 8) | (0x1F << 1)),
-	.release_ret_regs = exynos_release_ret_regs,
 	.pm_suspend	= exynos_pm_suspend,
 	.pm_resume	= exynos_pm_resume,
 	.pm_prepare	= exynos_pm_prepare,
@@ -656,7 +594,6 @@ static void exynos_suspend_finish(void)
 static const struct exynos_pm_data exynos5250_pm_data = {
 	.wkup_irq	= exynos5250_wkup_irq,
 	.wake_disable_mask = ((0xFF << 8) | (0x1F << 1)),
-	.release_ret_regs = exynos_release_ret_regs,
 	.pm_suspend	= exynos_pm_suspend,
 	.pm_resume	= exynos_pm_resume,
 	.pm_prepare	= exynos_pm_prepare,
@@ -666,7 +603,6 @@ static void exynos_suspend_finish(void)
 static const struct exynos_pm_data exynos5420_pm_data = {
 	.wkup_irq	= exynos5250_wkup_irq,
 	.wake_disable_mask = (0x7F << 7) | (0x1F << 1),
-	.release_ret_regs = exynos5420_release_ret_regs,
 	.pm_resume_prepare = exynos5420_prepare_pm_resume,
 	.pm_resume	= exynos5420_pm_resume,
 	.pm_suspend	= exynos5420_pm_suspend,
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index 70b94ad10cc1..7beb0d4d2f20 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -28,7 +28,10 @@
 #include <linux/io.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
+#include <linux/regmap.h>
 #include <linux/err.h>
+#include <linux/soc/samsung/exynos-pmu.h>
+#include <linux/soc/samsung/exynos-regs-pmu.h>
 
 #include "pinctrl-samsung.h"
 #include "pinctrl-exynos.h"
@@ -690,6 +693,55 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 	},
 };
 
+/* Pad retention control code for accessing PMU regmap */
+static atomic_t exynos_shared_retention_refcnt;
+
+static void exynos_retention_enable(struct samsung_pinctrl_drv_data *drvdata)
+{
+	if (drvdata->retention_ctrl->refcnt)
+		atomic_inc(drvdata->retention_ctrl->refcnt);
+}
+
+static void exynos_retention_disable(struct samsung_pinctrl_drv_data *drvdata)
+{
+	struct regmap *pmu_regs = drvdata->retention_ctrl->priv;
+	int i;
+
+	if (drvdata->retention_ctrl->refcnt &&
+	    !atomic_dec_and_test(drvdata->retention_ctrl->refcnt))
+		return;
+
+	for (i = 0; i < drvdata->retention_ctrl->nr_regs; i++)
+		regmap_write(pmu_regs, drvdata->retention_ctrl->regs[i],
+			     drvdata->retention_ctrl->value);
+}
+
+static struct samsung_retention_ctrl *
+exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata,
+		      const struct samsung_retention_data *data)
+{
+	struct samsung_retention_ctrl *ctrl;
+	struct regmap *pmu_regs;
+
+	ctrl = devm_kzalloc(drvdata->dev, sizeof(*ctrl), GFP_KERNEL);
+	if (!ctrl)
+		return ERR_PTR(-ENOMEM);
+
+	pmu_regs = exynos_get_pmu_regmap();
+	if (IS_ERR(pmu_regs))
+		return ERR_CAST(pmu_regs);
+
+	ctrl->priv = pmu_regs;
+	ctrl->regs = data->regs;
+	ctrl->nr_regs = data->nr_regs;
+	ctrl->value = data->value;
+	ctrl->refcnt = data->refcnt;
+	ctrl->enable = exynos_retention_enable;
+	ctrl->disable = exynos_retention_disable;
+
+	return ctrl;
+}
+
 /* pin banks of exynos3250 pin-controller 0 */
 static const struct samsung_pin_bank_data exynos3250_pin_banks0[] __initconst = {
 	EXYNOS_PIN_BANK_EINTG(8, 0x000, "gpa0", 0x00),
@@ -722,6 +774,30 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 };
 
 /*
+ * PMU pad retention groups for Exynos3250 doesn't match pin banks, so handle
+ * them all together
+ */
+static const u32 exynos3250_retention_regs[] = {
+	S5P_PAD_RET_MAUDIO_OPTION,
+	S5P_PAD_RET_GPIO_OPTION,
+	S5P_PAD_RET_UART_OPTION,
+	S5P_PAD_RET_MMCA_OPTION,
+	S5P_PAD_RET_MMCB_OPTION,
+	S5P_PAD_RET_EBIA_OPTION,
+	S5P_PAD_RET_EBIB_OPTION,
+	S5P_PAD_RET_MMC2_OPTION,
+	S5P_PAD_RET_SPI_OPTION,
+};
+
+static const struct samsung_retention_data exynos3250_retention_data __initconst = {
+	.regs	 = exynos3250_retention_regs,
+	.nr_regs = ARRAY_SIZE(exynos3250_retention_regs),
+	.value	 = EXYNOS_WAKEUP_FROM_LOWPWR,
+	.refcnt	 = &exynos_shared_retention_refcnt,
+	.init	 = exynos_retention_init,
+};
+
+/*
  * Samsung pinctrl driver data for Exynos3250 SoC. Exynos3250 SoC includes
  * two gpio/pin-mux/pinconfig controllers.
  */
@@ -733,6 +809,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos3250_retention_data,
 	}, {
 		/* pin-controller instance 1 data */
 		.pin_banks	= exynos3250_pin_banks1,
@@ -741,6 +818,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_wkup_init = exynos_eint_wkup_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos3250_retention_data,
 	},
 };
 
@@ -793,6 +871,36 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 	EXYNOS_PIN_BANK_EINTN(7, 0x000, "gpz"),
 };
 
+/* PMU pad retention groups registers for Exynos4 (without audio) */
+static const u32 exynos4_retention_regs[] = {
+	S5P_PAD_RET_GPIO_OPTION,
+	S5P_PAD_RET_UART_OPTION,
+	S5P_PAD_RET_MMCA_OPTION,
+	S5P_PAD_RET_MMCB_OPTION,
+	S5P_PAD_RET_EBIA_OPTION,
+	S5P_PAD_RET_EBIB_OPTION,
+};
+
+static const struct samsung_retention_data exynos4_retention_data __initconst = {
+	.regs	 = exynos4_retention_regs,
+	.nr_regs = ARRAY_SIZE(exynos4_retention_regs),
+	.value	 = EXYNOS_WAKEUP_FROM_LOWPWR,
+	.refcnt	 = &exynos_shared_retention_refcnt,
+	.init	 = exynos_retention_init,
+};
+
+/* PMU retention control for audio pins can be tied to audio pin bank */
+static const u32 exynos4_audio_retention_regs[] = {
+	S5P_PAD_RET_MAUDIO_OPTION,
+};
+
+static const struct samsung_retention_data exynos4_audio_retention_data __initconst = {
+	.regs	 = exynos4_audio_retention_regs,
+	.nr_regs = ARRAY_SIZE(exynos4_audio_retention_regs),
+	.value	 = EXYNOS_WAKEUP_FROM_LOWPWR,
+	.init	 = exynos_retention_init,
+};
+
 /*
  * Samsung pinctrl driver data for Exynos4210 SoC. Exynos4210 SoC includes
  * three gpio/pin-mux/pinconfig controllers.
@@ -805,6 +913,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 1 data */
 		.pin_banks	= exynos4210_pin_banks1,
@@ -813,10 +922,12 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_wkup_init = exynos_eint_wkup_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 2 data */
 		.pin_banks	= exynos4210_pin_banks2,
 		.nr_banks	= ARRAY_SIZE(exynos4210_pin_banks2),
+		.retention_data	= &exynos4_audio_retention_data,
 	},
 };
 
@@ -890,6 +1001,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 1 data */
 		.pin_banks	= exynos4x12_pin_banks1,
@@ -898,6 +1010,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_wkup_init = exynos_eint_wkup_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 2 data */
 		.pin_banks	= exynos4x12_pin_banks2,
@@ -905,6 +1018,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_audio_retention_data,
 	}, {
 		/* pin-controller instance 3 data */
 		.pin_banks	= exynos4x12_pin_banks3,
@@ -984,6 +1098,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_wkup_init = exynos_eint_wkup_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 1 data */
 		.pin_banks	= exynos5250_pin_banks1,
@@ -991,6 +1106,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 2 data */
 		.pin_banks	= exynos5250_pin_banks2,
@@ -1005,6 +1121,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_audio_retention_data,
 	},
 };
 
@@ -1231,6 +1348,30 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 	EXYNOS_PIN_BANK_EINTG(7, 0x000, "gpz", 0x00),
 };
 
+/* PMU pad retention groups registers for Exynos5420 (without audio) */
+static const u32 exynos5420_retention_regs[] = {
+	EXYNOS_PAD_RET_DRAM_OPTION,
+	EXYNOS_PAD_RET_JTAG_OPTION,
+	EXYNOS5420_PAD_RET_GPIO_OPTION,
+	EXYNOS5420_PAD_RET_UART_OPTION,
+	EXYNOS5420_PAD_RET_MMCA_OPTION,
+	EXYNOS5420_PAD_RET_MMCB_OPTION,
+	EXYNOS5420_PAD_RET_MMCC_OPTION,
+	EXYNOS5420_PAD_RET_HSI_OPTION,
+	EXYNOS_PAD_RET_EBIA_OPTION,
+	EXYNOS_PAD_RET_EBIB_OPTION,
+	EXYNOS5420_PAD_RET_SPI_OPTION,
+	EXYNOS5420_PAD_RET_DRAM_COREBLK_OPTION,
+};
+
+static const struct samsung_retention_data exynos5420_retention_data __initconst = {
+	.regs	 = exynos5420_retention_regs,
+	.nr_regs = ARRAY_SIZE(exynos5420_retention_regs),
+	.value	 = EXYNOS_WAKEUP_FROM_LOWPWR,
+	.refcnt	 = &exynos_shared_retention_refcnt,
+	.init	 = exynos_retention_init,
+};
+
 /*
  * Samsung pinctrl driver data for Exynos5420 SoC. Exynos5420 SoC includes
  * four gpio/pin-mux/pinconfig controllers.
@@ -1242,26 +1383,31 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.nr_banks	= ARRAY_SIZE(exynos5420_pin_banks0),
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.eint_wkup_init = exynos_eint_wkup_init,
+		.retention_data	= &exynos5420_retention_data,
 	}, {
 		/* pin-controller instance 1 data */
 		.pin_banks	= exynos5420_pin_banks1,
 		.nr_banks	= ARRAY_SIZE(exynos5420_pin_banks1),
 		.eint_gpio_init = exynos_eint_gpio_init,
+		.retention_data	= &exynos5420_retention_data,
 	}, {
 		/* pin-controller instance 2 data */
 		.pin_banks	= exynos5420_pin_banks2,
 		.nr_banks	= ARRAY_SIZE(exynos5420_pin_banks2),
 		.eint_gpio_init = exynos_eint_gpio_init,
+		.retention_data	= &exynos5420_retention_data,
 	}, {
 		/* pin-controller instance 3 data */
 		.pin_banks	= exynos5420_pin_banks3,
 		.nr_banks	= ARRAY_SIZE(exynos5420_pin_banks3),
 		.eint_gpio_init = exynos_eint_gpio_init,
+		.retention_data	= &exynos5420_retention_data,
 	}, {
 		/* pin-controller instance 4 data */
 		.pin_banks	= exynos5420_pin_banks4,
 		.nr_banks	= ARRAY_SIZE(exynos5420_pin_banks4),
 		.eint_gpio_init = exynos_eint_gpio_init,
+		.retention_data	= &exynos4_audio_retention_data,
 	},
 };
 
-- 
1.9.1

[PATCH v2 11/13] pinctrl: samsung: Move retention control from mach-exynos to the pinctrl driver

[Marek Szyprowski]

This patch moves pad retention control from PMU driver to Exynos pin
controller driver. This helps to avoid possible ordering and logical
dependencies between machine, PMU and pin control code. Till now it
worked fine only because sys_ops for PMU and pin controller were called
in registration order.
This is also a preparation for adding new features to Exynos pin
controller driver, like runtime power management and suspending
individual pin controllers, which might be a part of some power domain.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 arch/arm/mach-exynos/suspend.c           |  64 --------------
 drivers/pinctrl/samsung/pinctrl-exynos.c | 146 +++++++++++++++++++++++++++++++
 2 files changed, 146 insertions(+), 64 deletions(-)

diff --git a/arch/arm/mach-exynos/suspend.c b/arch/arm/mach-exynos/suspend.c
index 25e7c5326259..312d3a886e92 100644
--- a/arch/arm/mach-exynos/suspend.c
+++ b/arch/arm/mach-exynos/suspend.c
@@ -57,7 +57,6 @@ struct exynos_wkup_irq {
 struct exynos_pm_data {
 	const struct exynos_wkup_irq *wkup_irq;
 	unsigned int wake_disable_mask;
-	const unsigned int *release_ret_regs;
 
 	void (*pm_prepare)(void);
 	void (*pm_resume_prepare)(void);
@@ -95,47 +94,6 @@ struct exynos_pm_data {
 	{ /* sentinel */ },
 };
 
-static const unsigned int exynos_release_ret_regs[] = {
-	S5P_PAD_RET_MAUDIO_OPTION,
-	S5P_PAD_RET_GPIO_OPTION,
-	S5P_PAD_RET_UART_OPTION,
-	S5P_PAD_RET_MMCA_OPTION,
-	S5P_PAD_RET_MMCB_OPTION,
-	S5P_PAD_RET_EBIA_OPTION,
-	S5P_PAD_RET_EBIB_OPTION,
-	REG_TABLE_END,
-};
-
-static const unsigned int exynos3250_release_ret_regs[] = {
-	S5P_PAD_RET_MAUDIO_OPTION,
-	S5P_PAD_RET_GPIO_OPTION,
-	S5P_PAD_RET_UART_OPTION,
-	S5P_PAD_RET_MMCA_OPTION,
-	S5P_PAD_RET_MMCB_OPTION,
-	S5P_PAD_RET_EBIA_OPTION,
-	S5P_PAD_RET_EBIB_OPTION,
-	S5P_PAD_RET_MMC2_OPTION,
-	S5P_PAD_RET_SPI_OPTION,
-	REG_TABLE_END,
-};
-
-static const unsigned int exynos5420_release_ret_regs[] = {
-	EXYNOS_PAD_RET_DRAM_OPTION,
-	EXYNOS_PAD_RET_MAUDIO_OPTION,
-	EXYNOS_PAD_RET_JTAG_OPTION,
-	EXYNOS5420_PAD_RET_GPIO_OPTION,
-	EXYNOS5420_PAD_RET_UART_OPTION,
-	EXYNOS5420_PAD_RET_MMCA_OPTION,
-	EXYNOS5420_PAD_RET_MMCB_OPTION,
-	EXYNOS5420_PAD_RET_MMCC_OPTION,
-	EXYNOS5420_PAD_RET_HSI_OPTION,
-	EXYNOS_PAD_RET_EBIA_OPTION,
-	EXYNOS_PAD_RET_EBIB_OPTION,
-	EXYNOS5420_PAD_RET_SPI_OPTION,
-	EXYNOS5420_PAD_RET_DRAM_COREBLK_OPTION,
-	REG_TABLE_END,
-};
-
 static int exynos_irq_set_wake(struct irq_data *data, unsigned int state)
 {
 	const struct exynos_wkup_irq *wkup_irq;
@@ -441,15 +399,6 @@ static int exynos5420_pm_suspend(void)
 	return 0;
 }
 
-static void exynos_pm_release_retention(void)
-{
-	unsigned int i;
-
-	for (i = 0; (pm_data->release_ret_regs[i] != REG_TABLE_END); i++)
-		pmu_raw_writel(EXYNOS_WAKEUP_FROM_LOWPWR,
-				pm_data->release_ret_regs[i]);
-}
-
 static void exynos_pm_resume(void)
 {
 	u32 cpuid = read_cpuid_part();
@@ -457,9 +406,6 @@ static void exynos_pm_resume(void)
 	if (exynos_pm_central_resume())
 		goto early_wakeup;
 
-	/* For release retention */
-	exynos_pm_release_retention();
-
 	if (cpuid == ARM_CPU_PART_CORTEX_A9)
 		scu_enable(S5P_VA_SCU);
 
@@ -481,9 +427,6 @@ static void exynos3250_pm_resume(void)
 	if (exynos_pm_central_resume())
 		goto early_wakeup;
 
-	/* For release retention */
-	exynos_pm_release_retention();
-
 	pmu_raw_writel(S5P_USE_STANDBY_WFI_ALL, S5P_CENTRAL_SEQ_OPTION);
 
 	if (call_firmware_op(resume) == -ENOSYS
@@ -521,9 +464,6 @@ static void exynos5420_pm_resume(void)
 	if (exynos_pm_central_resume())
 		goto early_wakeup;
 
-	/* For release retention */
-	exynos_pm_release_retention();
-
 	pmu_raw_writel(exynos_pmu_spare3, S5P_PMU_SPARE3);
 
 early_wakeup:
@@ -636,7 +576,6 @@ static void exynos_suspend_finish(void)
 static const struct exynos_pm_data exynos3250_pm_data = {
 	.wkup_irq	= exynos3250_wkup_irq,
 	.wake_disable_mask = ((0xFF << 8) | (0x1F << 1)),
-	.release_ret_regs = exynos3250_release_ret_regs,
 	.pm_suspend	= exynos_pm_suspend,
 	.pm_resume	= exynos3250_pm_resume,
 	.pm_prepare	= exynos3250_pm_prepare,
@@ -646,7 +585,6 @@ static void exynos_suspend_finish(void)
 static const struct exynos_pm_data exynos4_pm_data = {
 	.wkup_irq	= exynos4_wkup_irq,
 	.wake_disable_mask = ((0xFF << 8) | (0x1F << 1)),
-	.release_ret_regs = exynos_release_ret_regs,
 	.pm_suspend	= exynos_pm_suspend,
 	.pm_resume	= exynos_pm_resume,
 	.pm_prepare	= exynos_pm_prepare,
@@ -656,7 +594,6 @@ static void exynos_suspend_finish(void)
 static const struct exynos_pm_data exynos5250_pm_data = {
 	.wkup_irq	= exynos5250_wkup_irq,
 	.wake_disable_mask = ((0xFF << 8) | (0x1F << 1)),
-	.release_ret_regs = exynos_release_ret_regs,
 	.pm_suspend	= exynos_pm_suspend,
 	.pm_resume	= exynos_pm_resume,
 	.pm_prepare	= exynos_pm_prepare,
@@ -666,7 +603,6 @@ static void exynos_suspend_finish(void)
 static const struct exynos_pm_data exynos5420_pm_data = {
 	.wkup_irq	= exynos5250_wkup_irq,
 	.wake_disable_mask = (0x7F << 7) | (0x1F << 1),
-	.release_ret_regs = exynos5420_release_ret_regs,
 	.pm_resume_prepare = exynos5420_prepare_pm_resume,
 	.pm_resume	= exynos5420_pm_resume,
 	.pm_suspend	= exynos5420_pm_suspend,
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index 70b94ad10cc1..7beb0d4d2f20 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -28,7 +28,10 @@
 #include <linux/io.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
+#include <linux/regmap.h>
 #include <linux/err.h>
+#include <linux/soc/samsung/exynos-pmu.h>
+#include <linux/soc/samsung/exynos-regs-pmu.h>
 
 #include "pinctrl-samsung.h"
 #include "pinctrl-exynos.h"
@@ -690,6 +693,55 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 	},
 };
 
+/* Pad retention control code for accessing PMU regmap */
+static atomic_t exynos_shared_retention_refcnt;
+
+static void exynos_retention_enable(struct samsung_pinctrl_drv_data *drvdata)
+{
+	if (drvdata->retention_ctrl->refcnt)
+		atomic_inc(drvdata->retention_ctrl->refcnt);
+}
+
+static void exynos_retention_disable(struct samsung_pinctrl_drv_data *drvdata)
+{
+	struct regmap *pmu_regs = drvdata->retention_ctrl->priv;
+	int i;
+
+	if (drvdata->retention_ctrl->refcnt &&
+	    !atomic_dec_and_test(drvdata->retention_ctrl->refcnt))
+		return;
+
+	for (i = 0; i < drvdata->retention_ctrl->nr_regs; i++)
+		regmap_write(pmu_regs, drvdata->retention_ctrl->regs[i],
+			     drvdata->retention_ctrl->value);
+}
+
+static struct samsung_retention_ctrl *
+exynos_retention_init(struct samsung_pinctrl_drv_data *drvdata,
+		      const struct samsung_retention_data *data)
+{
+	struct samsung_retention_ctrl *ctrl;
+	struct regmap *pmu_regs;
+
+	ctrl = devm_kzalloc(drvdata->dev, sizeof(*ctrl), GFP_KERNEL);
+	if (!ctrl)
+		return ERR_PTR(-ENOMEM);
+
+	pmu_regs = exynos_get_pmu_regmap();
+	if (IS_ERR(pmu_regs))
+		return ERR_CAST(pmu_regs);
+
+	ctrl->priv = pmu_regs;
+	ctrl->regs = data->regs;
+	ctrl->nr_regs = data->nr_regs;
+	ctrl->value = data->value;
+	ctrl->refcnt = data->refcnt;
+	ctrl->enable = exynos_retention_enable;
+	ctrl->disable = exynos_retention_disable;
+
+	return ctrl;
+}
+
 /* pin banks of exynos3250 pin-controller 0 */
 static const struct samsung_pin_bank_data exynos3250_pin_banks0[] __initconst = {
 	EXYNOS_PIN_BANK_EINTG(8, 0x000, "gpa0", 0x00),
@@ -722,6 +774,30 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 };
 
 /*
+ * PMU pad retention groups for Exynos3250 doesn't match pin banks, so handle
+ * them all together
+ */
+static const u32 exynos3250_retention_regs[] = {
+	S5P_PAD_RET_MAUDIO_OPTION,
+	S5P_PAD_RET_GPIO_OPTION,
+	S5P_PAD_RET_UART_OPTION,
+	S5P_PAD_RET_MMCA_OPTION,
+	S5P_PAD_RET_MMCB_OPTION,
+	S5P_PAD_RET_EBIA_OPTION,
+	S5P_PAD_RET_EBIB_OPTION,
+	S5P_PAD_RET_MMC2_OPTION,
+	S5P_PAD_RET_SPI_OPTION,
+};
+
+static const struct samsung_retention_data exynos3250_retention_data __initconst = {
+	.regs	 = exynos3250_retention_regs,
+	.nr_regs = ARRAY_SIZE(exynos3250_retention_regs),
+	.value	 = EXYNOS_WAKEUP_FROM_LOWPWR,
+	.refcnt	 = &exynos_shared_retention_refcnt,
+	.init	 = exynos_retention_init,
+};
+
+/*
  * Samsung pinctrl driver data for Exynos3250 SoC. Exynos3250 SoC includes
  * two gpio/pin-mux/pinconfig controllers.
  */
@@ -733,6 +809,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos3250_retention_data,
 	}, {
 		/* pin-controller instance 1 data */
 		.pin_banks	= exynos3250_pin_banks1,
@@ -741,6 +818,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_wkup_init = exynos_eint_wkup_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos3250_retention_data,
 	},
 };
 
@@ -793,6 +871,36 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 	EXYNOS_PIN_BANK_EINTN(7, 0x000, "gpz"),
 };
 
+/* PMU pad retention groups registers for Exynos4 (without audio) */
+static const u32 exynos4_retention_regs[] = {
+	S5P_PAD_RET_GPIO_OPTION,
+	S5P_PAD_RET_UART_OPTION,
+	S5P_PAD_RET_MMCA_OPTION,
+	S5P_PAD_RET_MMCB_OPTION,
+	S5P_PAD_RET_EBIA_OPTION,
+	S5P_PAD_RET_EBIB_OPTION,
+};
+
+static const struct samsung_retention_data exynos4_retention_data __initconst = {
+	.regs	 = exynos4_retention_regs,
+	.nr_regs = ARRAY_SIZE(exynos4_retention_regs),
+	.value	 = EXYNOS_WAKEUP_FROM_LOWPWR,
+	.refcnt	 = &exynos_shared_retention_refcnt,
+	.init	 = exynos_retention_init,
+};
+
+/* PMU retention control for audio pins can be tied to audio pin bank */
+static const u32 exynos4_audio_retention_regs[] = {
+	S5P_PAD_RET_MAUDIO_OPTION,
+};
+
+static const struct samsung_retention_data exynos4_audio_retention_data __initconst = {
+	.regs	 = exynos4_audio_retention_regs,
+	.nr_regs = ARRAY_SIZE(exynos4_audio_retention_regs),
+	.value	 = EXYNOS_WAKEUP_FROM_LOWPWR,
+	.init	 = exynos_retention_init,
+};
+
 /*
  * Samsung pinctrl driver data for Exynos4210 SoC. Exynos4210 SoC includes
  * three gpio/pin-mux/pinconfig controllers.
@@ -805,6 +913,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 1 data */
 		.pin_banks	= exynos4210_pin_banks1,
@@ -813,10 +922,12 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_wkup_init = exynos_eint_wkup_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 2 data */
 		.pin_banks	= exynos4210_pin_banks2,
 		.nr_banks	= ARRAY_SIZE(exynos4210_pin_banks2),
+		.retention_data	= &exynos4_audio_retention_data,
 	},
 };
 
@@ -890,6 +1001,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 1 data */
 		.pin_banks	= exynos4x12_pin_banks1,
@@ -898,6 +1010,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_wkup_init = exynos_eint_wkup_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 2 data */
 		.pin_banks	= exynos4x12_pin_banks2,
@@ -905,6 +1018,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_audio_retention_data,
 	}, {
 		/* pin-controller instance 3 data */
 		.pin_banks	= exynos4x12_pin_banks3,
@@ -984,6 +1098,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_wkup_init = exynos_eint_wkup_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 1 data */
 		.pin_banks	= exynos5250_pin_banks1,
@@ -991,6 +1106,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_retention_data,
 	}, {
 		/* pin-controller instance 2 data */
 		.pin_banks	= exynos5250_pin_banks2,
@@ -1005,6 +1121,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &exynos4_audio_retention_data,
 	},
 };
 
@@ -1231,6 +1348,30 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 	EXYNOS_PIN_BANK_EINTG(7, 0x000, "gpz", 0x00),
 };
 
+/* PMU pad retention groups registers for Exynos5420 (without audio) */
+static const u32 exynos5420_retention_regs[] = {
+	EXYNOS_PAD_RET_DRAM_OPTION,
+	EXYNOS_PAD_RET_JTAG_OPTION,
+	EXYNOS5420_PAD_RET_GPIO_OPTION,
+	EXYNOS5420_PAD_RET_UART_OPTION,
+	EXYNOS5420_PAD_RET_MMCA_OPTION,
+	EXYNOS5420_PAD_RET_MMCB_OPTION,
+	EXYNOS5420_PAD_RET_MMCC_OPTION,
+	EXYNOS5420_PAD_RET_HSI_OPTION,
+	EXYNOS_PAD_RET_EBIA_OPTION,
+	EXYNOS_PAD_RET_EBIB_OPTION,
+	EXYNOS5420_PAD_RET_SPI_OPTION,
+	EXYNOS5420_PAD_RET_DRAM_COREBLK_OPTION,
+};
+
+static const struct samsung_retention_data exynos5420_retention_data __initconst = {
+	.regs	 = exynos5420_retention_regs,
+	.nr_regs = ARRAY_SIZE(exynos5420_retention_regs),
+	.value	 = EXYNOS_WAKEUP_FROM_LOWPWR,
+	.refcnt	 = &exynos_shared_retention_refcnt,
+	.init	 = exynos_retention_init,
+};
+
 /*
  * Samsung pinctrl driver data for Exynos5420 SoC. Exynos5420 SoC includes
  * four gpio/pin-mux/pinconfig controllers.
@@ -1242,26 +1383,31 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.nr_banks	= ARRAY_SIZE(exynos5420_pin_banks0),
 		.eint_gpio_init = exynos_eint_gpio_init,
 		.eint_wkup_init = exynos_eint_wkup_init,
+		.retention_data	= &exynos5420_retention_data,
 	}, {
 		/* pin-controller instance 1 data */
 		.pin_banks	= exynos5420_pin_banks1,
 		.nr_banks	= ARRAY_SIZE(exynos5420_pin_banks1),
 		.eint_gpio_init = exynos_eint_gpio_init,
+		.retention_data	= &exynos5420_retention_data,
 	}, {
 		/* pin-controller instance 2 data */
 		.pin_banks	= exynos5420_pin_banks2,
 		.nr_banks	= ARRAY_SIZE(exynos5420_pin_banks2),
 		.eint_gpio_init = exynos_eint_gpio_init,
+		.retention_data	= &exynos5420_retention_data,
 	}, {
 		/* pin-controller instance 3 data */
 		.pin_banks	= exynos5420_pin_banks3,
 		.nr_banks	= ARRAY_SIZE(exynos5420_pin_banks3),
 		.eint_gpio_init = exynos_eint_gpio_init,
+		.retention_data	= &exynos5420_retention_data,
 	}, {
 		/* pin-controller instance 4 data */
 		.pin_banks	= exynos5420_pin_banks4,
 		.nr_banks	= ARRAY_SIZE(exynos5420_pin_banks4),
 		.eint_gpio_init = exynos_eint_gpio_init,
+		.retention_data	= &exynos4_audio_retention_data,
 	},
 };
 
-- 
1.9.1

Re: [PATCH v2 11/13] pinctrl: samsung: Move retention control from mach-exynos to the pinctrl driver

[Krzysztof Kozlowski]

On Tue, Jan 17, 2017 at 01:44:42PM +0100, Marek Szyprowski wrote:
> This patch moves pad retention control from PMU driver to Exynos pin
> controller driver. This helps to avoid possible ordering and logical
> dependencies between machine, PMU and pin control code. Till now it
> worked fine only because sys_ops for PMU and pin controller were called
> in registration order.
> This is also a preparation for adding new features to Exynos pin
> controller driver, like runtime power management and suspending
> individual pin controllers, which might be a part of some power domain.
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> ---
>  arch/arm/mach-exynos/suspend.c           |  64 --------------
>  drivers/pinctrl/samsung/pinctrl-exynos.c | 146 +++++++++++++++++++++++++++++++
>  2 files changed, 146 insertions(+), 64 deletions(-)
> 

Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>

Best regards,
Krzysztof

[PATCH v2 11/13] pinctrl: samsung: Move retention control from mach-exynos to the pinctrl driver

[Krzysztof Kozlowski]

On Tue, Jan 17, 2017 at 01:44:42PM +0100, Marek Szyprowski wrote:
> This patch moves pad retention control from PMU driver to Exynos pin
> controller driver. This helps to avoid possible ordering and logical
> dependencies between machine, PMU and pin control code. Till now it
> worked fine only because sys_ops for PMU and pin controller were called
> in registration order.
> This is also a preparation for adding new features to Exynos pin
> controller driver, like runtime power management and suspending
> individual pin controllers, which might be a part of some power domain.
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> ---
>  arch/arm/mach-exynos/suspend.c           |  64 --------------
>  drivers/pinctrl/samsung/pinctrl-exynos.c | 146 +++++++++++++++++++++++++++++++
>  2 files changed, 146 insertions(+), 64 deletions(-)
> 

Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>

Best regards,
Krzysztof

[PATCH v2 12/13] pinctrl: samsung: Move retention control from mach-s5pv210 to the pinctrl driver

[Marek Szyprowski]

This patch moves pad retention control from S5PV210 machine code to
Exynos pin controller driver. This helps to avoid possible ordering
and logical dependencies between machine and pin control code. Till
now it worked fine only because sys_ops for machine code and pin
controller were called in registration order.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 arch/arm/mach-s5pv210/pm.c               |  7 ----
 arch/arm/mach-s5pv210/regs-clock.h       |  4 ---
 drivers/pinctrl/samsung/pinctrl-exynos.c | 56 ++++++++++++++++++++++++++++++++
 3 files changed, 56 insertions(+), 11 deletions(-)

diff --git a/arch/arm/mach-s5pv210/pm.c b/arch/arm/mach-s5pv210/pm.c
index 21b4b13c5ab7..7d69666de5ba 100644
--- a/arch/arm/mach-s5pv210/pm.c
+++ b/arch/arm/mach-s5pv210/pm.c
@@ -155,13 +155,6 @@ static void s5pv210_suspend_finish(void)
  */
 static void s5pv210_pm_resume(void)
 {
-	u32 tmp;
-
-	tmp = __raw_readl(S5P_OTHERS);
-	tmp |= (S5P_OTHERS_RET_IO | S5P_OTHERS_RET_CF |\
-		S5P_OTHERS_RET_MMC | S5P_OTHERS_RET_UART);
-	__raw_writel(tmp , S5P_OTHERS);
-
 	s3c_pm_do_restore_core(s5pv210_core_save, ARRAY_SIZE(s5pv210_core_save));
 }
 
diff --git a/arch/arm/mach-s5pv210/regs-clock.h b/arch/arm/mach-s5pv210/regs-clock.h
index 4640f0f03c12..fb3eb77412db 100644
--- a/arch/arm/mach-s5pv210/regs-clock.h
+++ b/arch/arm/mach-s5pv210/regs-clock.h
@@ -188,10 +188,6 @@
 #define S5P_SLEEP_CFG_USBOSC_EN		(1 << 1)
 
 /* OTHERS Resgister */
-#define S5P_OTHERS_RET_IO		(1 << 31)
-#define S5P_OTHERS_RET_CF		(1 << 30)
-#define S5P_OTHERS_RET_MMC		(1 << 29)
-#define S5P_OTHERS_RET_UART		(1 << 28)
 #define S5P_OTHERS_USB_SIG_MASK		(1 << 16)
 
 /* S5P_DAC_CONTROL */
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index 7beb0d4d2f20..675a38e956f8 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -24,6 +24,7 @@
 #include <linux/irqdomain.h>
 #include <linux/irq.h>
 #include <linux/irqchip/chained_irq.h>
+#include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/io.h>
 #include <linux/slab.h>
@@ -643,6 +644,60 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 			exynos_pinctrl_resume_bank(drvdata, bank);
 }
 
+/* Retention control for S5PV210 are located at the end of clock controller */
+#define S5P_OTHERS 0xE000
+
+#define S5P_OTHERS_RET_IO		(1 << 31)
+#define S5P_OTHERS_RET_CF		(1 << 30)
+#define S5P_OTHERS_RET_MMC		(1 << 29)
+#define S5P_OTHERS_RET_UART		(1 << 28)
+
+static void s5pv210_retention_disable(struct samsung_pinctrl_drv_data *drvdata)
+{
+	void *clk_base = drvdata->retention_ctrl->priv;
+	u32 tmp;
+
+	tmp = __raw_readl(clk_base + S5P_OTHERS);
+	tmp |= (S5P_OTHERS_RET_IO | S5P_OTHERS_RET_CF | S5P_OTHERS_RET_MMC |
+		S5P_OTHERS_RET_UART);
+	__raw_writel(tmp, clk_base + S5P_OTHERS);
+}
+
+static struct samsung_retention_ctrl *
+s5pv210_retention_init(struct samsung_pinctrl_drv_data *drvdata,
+		       const struct samsung_retention_data *data)
+{
+	struct samsung_retention_ctrl *ctrl;
+	struct device_node *np;
+	void *clk_base;
+
+	ctrl = devm_kzalloc(drvdata->dev, sizeof(*ctrl), GFP_KERNEL);
+	if (!ctrl)
+		return ERR_PTR(-ENOMEM);
+
+	np = of_find_compatible_node(NULL, NULL, "samsung,s5pv210-clock");
+	if (!np) {
+		pr_err("%s: failed to find clock controller DT node\n",
+			__func__);
+		return ERR_PTR(-ENODEV);
+	}
+
+	clk_base = of_iomap(np, 0);
+	if (!clk_base) {
+		pr_err("%s: failed to map clock registers\n", __func__);
+		return ERR_PTR(-EINVAL);
+	}
+
+	ctrl->priv = clk_base;
+	ctrl->disable = s5pv210_retention_disable;
+
+	return ctrl;
+}
+
+static const struct samsung_retention_data s5pv210_retention_data __initconst = {
+	.init	 = s5pv210_retention_init,
+};
+
 /* pin banks of s5pv210 pin-controller */
 static const struct samsung_pin_bank_data s5pv210_pin_bank[] __initconst = {
 	EXYNOS_PIN_BANK_EINTG(8, 0x000, "gpa0", 0x00),
@@ -690,6 +745,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_wkup_init = exynos_eint_wkup_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &s5pv210_retention_data,
 	},
 };
 
-- 
1.9.1

[PATCH v2 12/13] pinctrl: samsung: Move retention control from mach-s5pv210 to the pinctrl driver

[Marek Szyprowski]

This patch moves pad retention control from S5PV210 machine code to
Exynos pin controller driver. This helps to avoid possible ordering
and logical dependencies between machine and pin control code. Till
now it worked fine only because sys_ops for machine code and pin
controller were called in registration order.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
---
 arch/arm/mach-s5pv210/pm.c               |  7 ----
 arch/arm/mach-s5pv210/regs-clock.h       |  4 ---
 drivers/pinctrl/samsung/pinctrl-exynos.c | 56 ++++++++++++++++++++++++++++++++
 3 files changed, 56 insertions(+), 11 deletions(-)

diff --git a/arch/arm/mach-s5pv210/pm.c b/arch/arm/mach-s5pv210/pm.c
index 21b4b13c5ab7..7d69666de5ba 100644
--- a/arch/arm/mach-s5pv210/pm.c
+++ b/arch/arm/mach-s5pv210/pm.c
@@ -155,13 +155,6 @@ static void s5pv210_suspend_finish(void)
  */
 static void s5pv210_pm_resume(void)
 {
-	u32 tmp;
-
-	tmp = __raw_readl(S5P_OTHERS);
-	tmp |= (S5P_OTHERS_RET_IO | S5P_OTHERS_RET_CF |\
-		S5P_OTHERS_RET_MMC | S5P_OTHERS_RET_UART);
-	__raw_writel(tmp , S5P_OTHERS);
-
 	s3c_pm_do_restore_core(s5pv210_core_save, ARRAY_SIZE(s5pv210_core_save));
 }
 
diff --git a/arch/arm/mach-s5pv210/regs-clock.h b/arch/arm/mach-s5pv210/regs-clock.h
index 4640f0f03c12..fb3eb77412db 100644
--- a/arch/arm/mach-s5pv210/regs-clock.h
+++ b/arch/arm/mach-s5pv210/regs-clock.h
@@ -188,10 +188,6 @@
 #define S5P_SLEEP_CFG_USBOSC_EN		(1 << 1)
 
 /* OTHERS Resgister */
-#define S5P_OTHERS_RET_IO		(1 << 31)
-#define S5P_OTHERS_RET_CF		(1 << 30)
-#define S5P_OTHERS_RET_MMC		(1 << 29)
-#define S5P_OTHERS_RET_UART		(1 << 28)
 #define S5P_OTHERS_USB_SIG_MASK		(1 << 16)
 
 /* S5P_DAC_CONTROL */
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index 7beb0d4d2f20..675a38e956f8 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -24,6 +24,7 @@
 #include <linux/irqdomain.h>
 #include <linux/irq.h>
 #include <linux/irqchip/chained_irq.h>
+#include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/io.h>
 #include <linux/slab.h>
@@ -643,6 +644,60 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 			exynos_pinctrl_resume_bank(drvdata, bank);
 }
 
+/* Retention control for S5PV210 are located at the end of clock controller */
+#define S5P_OTHERS 0xE000
+
+#define S5P_OTHERS_RET_IO		(1 << 31)
+#define S5P_OTHERS_RET_CF		(1 << 30)
+#define S5P_OTHERS_RET_MMC		(1 << 29)
+#define S5P_OTHERS_RET_UART		(1 << 28)
+
+static void s5pv210_retention_disable(struct samsung_pinctrl_drv_data *drvdata)
+{
+	void *clk_base = drvdata->retention_ctrl->priv;
+	u32 tmp;
+
+	tmp = __raw_readl(clk_base + S5P_OTHERS);
+	tmp |= (S5P_OTHERS_RET_IO | S5P_OTHERS_RET_CF | S5P_OTHERS_RET_MMC |
+		S5P_OTHERS_RET_UART);
+	__raw_writel(tmp, clk_base + S5P_OTHERS);
+}
+
+static struct samsung_retention_ctrl *
+s5pv210_retention_init(struct samsung_pinctrl_drv_data *drvdata,
+		       const struct samsung_retention_data *data)
+{
+	struct samsung_retention_ctrl *ctrl;
+	struct device_node *np;
+	void *clk_base;
+
+	ctrl = devm_kzalloc(drvdata->dev, sizeof(*ctrl), GFP_KERNEL);
+	if (!ctrl)
+		return ERR_PTR(-ENOMEM);
+
+	np = of_find_compatible_node(NULL, NULL, "samsung,s5pv210-clock");
+	if (!np) {
+		pr_err("%s: failed to find clock controller DT node\n",
+			__func__);
+		return ERR_PTR(-ENODEV);
+	}
+
+	clk_base = of_iomap(np, 0);
+	if (!clk_base) {
+		pr_err("%s: failed to map clock registers\n", __func__);
+		return ERR_PTR(-EINVAL);
+	}
+
+	ctrl->priv = clk_base;
+	ctrl->disable = s5pv210_retention_disable;
+
+	return ctrl;
+}
+
+static const struct samsung_retention_data s5pv210_retention_data __initconst = {
+	.init	 = s5pv210_retention_init,
+};
+
 /* pin banks of s5pv210 pin-controller */
 static const struct samsung_pin_bank_data s5pv210_pin_bank[] __initconst = {
 	EXYNOS_PIN_BANK_EINTG(8, 0x000, "gpa0", 0x00),
@@ -690,6 +745,7 @@ static void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
 		.eint_wkup_init = exynos_eint_wkup_init,
 		.suspend	= exynos_pinctrl_suspend,
 		.resume		= exynos_pinctrl_resume,
+		.retention_data	= &s5pv210_retention_data,
 	},
 };
 
-- 
1.9.1

Re: [PATCH v2 12/13] pinctrl: samsung: Move retention control from mach-s5pv210 to the pinctrl driver

[Krzysztof Kozlowski]

On Tue, Jan 17, 2017 at 01:44:43PM +0100, Marek Szyprowski wrote:
> This patch moves pad retention control from S5PV210 machine code to
> Exynos pin controller driver. This helps to avoid possible ordering
> and logical dependencies between machine and pin control code. Till
> now it worked fine only because sys_ops for machine code and pin
> controller were called in registration order.
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> ---
>  arch/arm/mach-s5pv210/pm.c               |  7 ----
>  arch/arm/mach-s5pv210/regs-clock.h       |  4 ---

For mach-s5pv210:
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>

Best regards,
Krzysztof

[PATCH v2 12/13] pinctrl: samsung: Move retention control from mach-s5pv210 to the pinctrl driver

[Krzysztof Kozlowski]

On Tue, Jan 17, 2017 at 01:44:43PM +0100, Marek Szyprowski wrote:
> This patch moves pad retention control from S5PV210 machine code to
> Exynos pin controller driver. This helps to avoid possible ordering
> and logical dependencies between machine and pin control code. Till
> now it worked fine only because sys_ops for machine code and pin
> controller were called in registration order.
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> ---
>  arch/arm/mach-s5pv210/pm.c               |  7 ----
>  arch/arm/mach-s5pv210/regs-clock.h       |  4 ---

For mach-s5pv210:
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>

Best regards,
Krzysztof

[PATCH v2 13/13] pinctrl: samsung: Replace syscore ops with standard platform device pm_ops

[Marek Szyprowski]

Once the dependency on PMU driver (for pad retention control) has been
removed, there is no reason to use syscore_ops based suspend/resume.
This patch replaces it with standard platform device pm_ops based solution.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 drivers/pinctrl/samsung/pinctrl-samsung.c | 72 ++++++-------------------------
 1 file changed, 14 insertions(+), 58 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 021abd7221f8..d79eadad6c5f 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -29,7 +29,6 @@
 #include <linux/irqdomain.h>
 #include <linux/of_device.h>
 #include <linux/spinlock.h>
-#include <linux/syscore_ops.h>
 
 #include "../core.h"
 #include "pinctrl-samsung.h"
@@ -49,9 +48,6 @@
 	{ "samsung,pin-val", PINCFG_TYPE_DAT },
 };
 
-/* Global list of devices (struct samsung_pinctrl_drv_data) */
-static LIST_HEAD(drvdata_list);
-
 static unsigned int pin_base;
 
 static int samsung_get_group_count(struct pinctrl_dev *pctldev)
@@ -1084,22 +1080,18 @@ static int samsung_pinctrl_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, drvdata);
 
-	/* Add to the global list */
-	list_add_tail(&drvdata->node, &drvdata_list);
-
 	return 0;
 }
 
 #ifdef CONFIG_PM
-
 /**
- * samsung_pinctrl_suspend_dev - save pinctrl state for suspend for a device
+ * samsung_pinctrl_suspend - save pinctrl state for suspend
  *
  * Save data for all banks handled by this device.
  */
-static void samsung_pinctrl_suspend_dev(
-	struct samsung_pinctrl_drv_data *drvdata)
+static int samsung_pinctrl_suspend(struct device *dev)
 {
+	struct samsung_pinctrl_drv_data *drvdata = dev_get_drvdata(dev);
 	int i;
 
 	for (i = 0; i < drvdata->nr_banks; i++) {
@@ -1135,18 +1127,21 @@ static void samsung_pinctrl_suspend_dev(
 		drvdata->suspend(drvdata);
 	if (drvdata->retention_ctrl && drvdata->retention_ctrl->enable)
 		drvdata->retention_ctrl->enable(drvdata);
+
+	return 0;
 }
 
 /**
- * samsung_pinctrl_resume_dev - restore pinctrl state from suspend for a device
+ * samsung_pinctrl_resume - restore pinctrl state from suspend
  *
  * Restore one of the banks that was saved during suspend.
  *
  * We don't bother doing anything complicated to avoid glitching lines since
  * we're called before pad retention is turned off.
  */
-static void samsung_pinctrl_resume_dev(struct samsung_pinctrl_drv_data *drvdata)
+static int samsung_pinctrl_resume(struct device *dev)
 {
+	struct samsung_pinctrl_drv_data *drvdata = dev_get_drvdata(dev);
 	int i;
 
 	if (drvdata->resume)
@@ -1185,48 +1180,11 @@ static void samsung_pinctrl_resume_dev(struct samsung_pinctrl_drv_data *drvdata)
 
 	if (drvdata->retention_ctrl && drvdata->retention_ctrl->disable)
 		drvdata->retention_ctrl->disable(drvdata);
-}
-
-/**
- * samsung_pinctrl_suspend - save pinctrl state for suspend
- *
- * Save data for all banks across all devices.
- */
-static int samsung_pinctrl_suspend(void)
-{
-	struct samsung_pinctrl_drv_data *drvdata;
-
-	list_for_each_entry(drvdata, &drvdata_list, node) {
-		samsung_pinctrl_suspend_dev(drvdata);
-	}
 
 	return 0;
 }
-
-/**
- * samsung_pinctrl_resume - restore pinctrl state for suspend
- *
- * Restore data for all banks across all devices.
- */
-static void samsung_pinctrl_resume(void)
-{
-	struct samsung_pinctrl_drv_data *drvdata;
-
-	list_for_each_entry_reverse(drvdata, &drvdata_list, node) {
-		samsung_pinctrl_resume_dev(drvdata);
-	}
-}
-
-#else
-#define samsung_pinctrl_suspend		NULL
-#define samsung_pinctrl_resume		NULL
 #endif
 
-static struct syscore_ops samsung_pinctrl_syscore_ops = {
-	.suspend	= samsung_pinctrl_suspend,
-	.resume		= samsung_pinctrl_resume,
-};
-
 static const struct of_device_id samsung_pinctrl_dt_match[] = {
 #ifdef CONFIG_PINCTRL_EXYNOS
 	{ .compatible = "samsung,exynos3250-pinctrl",
@@ -1268,25 +1226,23 @@ static void samsung_pinctrl_resume(void)
 };
 MODULE_DEVICE_TABLE(of, samsung_pinctrl_dt_match);
 
+static const struct dev_pm_ops samsung_pinctrl_pm_ops = {
+	SET_LATE_SYSTEM_SLEEP_PM_OPS(samsung_pinctrl_suspend,
+				     samsung_pinctrl_resume)
+};
+
 static struct platform_driver samsung_pinctrl_driver = {
 	.probe		= samsung_pinctrl_probe,
 	.driver = {
 		.name	= "samsung-pinctrl",
 		.of_match_table = samsung_pinctrl_dt_match,
 		.suppress_bind_attrs = true,
+		.pm = &samsung_pinctrl_pm_ops,
 	},
 };
 
 static int __init samsung_pinctrl_drv_register(void)
 {
-	/*
-	 * Register syscore ops for save/restore of registers across suspend.
-	 * It's important to ensure that this driver is running at an earlier
-	 * initcall level than any arch-specific init calls that install syscore
-	 * ops that turn off pad retention (like exynos_pm_resume).
-	 */
-	register_syscore_ops(&samsung_pinctrl_syscore_ops);
-
 	return platform_driver_register(&samsung_pinctrl_driver);
 }
 postcore_initcall(samsung_pinctrl_drv_register);
-- 
1.9.1

[PATCH v2 13/13] pinctrl: samsung: Replace syscore ops with standard platform device pm_ops

[Marek Szyprowski]

Once the dependency on PMU driver (for pad retention control) has been
removed, there is no reason to use syscore_ops based suspend/resume.
This patch replaces it with standard platform device pm_ops based solution.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 drivers/pinctrl/samsung/pinctrl-samsung.c | 72 ++++++-------------------------
 1 file changed, 14 insertions(+), 58 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c
index 021abd7221f8..d79eadad6c5f 100644
--- a/drivers/pinctrl/samsung/pinctrl-samsung.c
+++ b/drivers/pinctrl/samsung/pinctrl-samsung.c
@@ -29,7 +29,6 @@
 #include <linux/irqdomain.h>
 #include <linux/of_device.h>
 #include <linux/spinlock.h>
-#include <linux/syscore_ops.h>
 
 #include "../core.h"
 #include "pinctrl-samsung.h"
@@ -49,9 +48,6 @@
 	{ "samsung,pin-val", PINCFG_TYPE_DAT },
 };
 
-/* Global list of devices (struct samsung_pinctrl_drv_data) */
-static LIST_HEAD(drvdata_list);
-
 static unsigned int pin_base;
 
 static int samsung_get_group_count(struct pinctrl_dev *pctldev)
@@ -1084,22 +1080,18 @@ static int samsung_pinctrl_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, drvdata);
 
-	/* Add to the global list */
-	list_add_tail(&drvdata->node, &drvdata_list);
-
 	return 0;
 }
 
 #ifdef CONFIG_PM
-
 /**
- * samsung_pinctrl_suspend_dev - save pinctrl state for suspend for a device
+ * samsung_pinctrl_suspend - save pinctrl state for suspend
  *
  * Save data for all banks handled by this device.
  */
-static void samsung_pinctrl_suspend_dev(
-	struct samsung_pinctrl_drv_data *drvdata)
+static int samsung_pinctrl_suspend(struct device *dev)
 {
+	struct samsung_pinctrl_drv_data *drvdata = dev_get_drvdata(dev);
 	int i;
 
 	for (i = 0; i < drvdata->nr_banks; i++) {
@@ -1135,18 +1127,21 @@ static void samsung_pinctrl_suspend_dev(
 		drvdata->suspend(drvdata);
 	if (drvdata->retention_ctrl && drvdata->retention_ctrl->enable)
 		drvdata->retention_ctrl->enable(drvdata);
+
+	return 0;
 }
 
 /**
- * samsung_pinctrl_resume_dev - restore pinctrl state from suspend for a device
+ * samsung_pinctrl_resume - restore pinctrl state from suspend
  *
  * Restore one of the banks that was saved during suspend.
  *
  * We don't bother doing anything complicated to avoid glitching lines since
  * we're called before pad retention is turned off.
  */
-static void samsung_pinctrl_resume_dev(struct samsung_pinctrl_drv_data *drvdata)
+static int samsung_pinctrl_resume(struct device *dev)
 {
+	struct samsung_pinctrl_drv_data *drvdata = dev_get_drvdata(dev);
 	int i;
 
 	if (drvdata->resume)
@@ -1185,48 +1180,11 @@ static void samsung_pinctrl_resume_dev(struct samsung_pinctrl_drv_data *drvdata)
 
 	if (drvdata->retention_ctrl && drvdata->retention_ctrl->disable)
 		drvdata->retention_ctrl->disable(drvdata);
-}
-
-/**
- * samsung_pinctrl_suspend - save pinctrl state for suspend
- *
- * Save data for all banks across all devices.
- */
-static int samsung_pinctrl_suspend(void)
-{
-	struct samsung_pinctrl_drv_data *drvdata;
-
-	list_for_each_entry(drvdata, &drvdata_list, node) {
-		samsung_pinctrl_suspend_dev(drvdata);
-	}
 
 	return 0;
 }
-
-/**
- * samsung_pinctrl_resume - restore pinctrl state for suspend
- *
- * Restore data for all banks across all devices.
- */
-static void samsung_pinctrl_resume(void)
-{
-	struct samsung_pinctrl_drv_data *drvdata;
-
-	list_for_each_entry_reverse(drvdata, &drvdata_list, node) {
-		samsung_pinctrl_resume_dev(drvdata);
-	}
-}
-
-#else
-#define samsung_pinctrl_suspend		NULL
-#define samsung_pinctrl_resume		NULL
 #endif
 
-static struct syscore_ops samsung_pinctrl_syscore_ops = {
-	.suspend	= samsung_pinctrl_suspend,
-	.resume		= samsung_pinctrl_resume,
-};
-
 static const struct of_device_id samsung_pinctrl_dt_match[] = {
 #ifdef CONFIG_PINCTRL_EXYNOS
 	{ .compatible = "samsung,exynos3250-pinctrl",
@@ -1268,25 +1226,23 @@ static void samsung_pinctrl_resume(void)
 };
 MODULE_DEVICE_TABLE(of, samsung_pinctrl_dt_match);
 
+static const struct dev_pm_ops samsung_pinctrl_pm_ops = {
+	SET_LATE_SYSTEM_SLEEP_PM_OPS(samsung_pinctrl_suspend,
+				     samsung_pinctrl_resume)
+};
+
 static struct platform_driver samsung_pinctrl_driver = {
 	.probe		= samsung_pinctrl_probe,
 	.driver = {
 		.name	= "samsung-pinctrl",
 		.of_match_table = samsung_pinctrl_dt_match,
 		.suppress_bind_attrs = true,
+		.pm = &samsung_pinctrl_pm_ops,
 	},
 };
 
 static int __init samsung_pinctrl_drv_register(void)
 {
-	/*
-	 * Register syscore ops for save/restore of registers across suspend.
-	 * It's important to ensure that this driver is running at an earlier
-	 * initcall level than any arch-specific init calls that install syscore
-	 * ops that turn off pad retention (like exynos_pm_resume).
-	 */
-	register_syscore_ops(&samsung_pinctrl_syscore_ops);
-
 	return platform_driver_register(&samsung_pinctrl_driver);
 }
 postcore_initcall(samsung_pinctrl_drv_register);
-- 
1.9.1

Re: [PATCH v2 00/13] Move pad retention control to Exynos pin controller driver

[Tomasz Figa]

Hi Marek,

2017-01-17 21:44 GMT+09:00 Marek Szyprowski <m.szyprowski@samsung.com>:
> Changelog:
>
> v2:
> - reworked exynos_get_pmu_regmap() function and moved to Exynos PMU driver,
>   now it doesn't depend on driver probe order thus doesn't need to defer probing
>   of pinctrl driver if PMU has not yet been probed
> - collected Acks, minor fixes according to review comments

After fixing remaining nits in patch 1 and 10, for all pinctrl patches (4-13):

Acked-by: Tomasz Figa <tomasz.figa@gmail.com>

and for other patches (1-3):

Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>

Best regards,
Tomasz

[PATCH v2 00/13] Move pad retention control to Exynos pin controller driver

[Tomasz Figa]

Hi Marek,

2017-01-17 21:44 GMT+09:00 Marek Szyprowski <m.szyprowski@samsung.com>:
> Changelog:
>
> v2:
> - reworked exynos_get_pmu_regmap() function and moved to Exynos PMU driver,
>   now it doesn't depend on driver probe order thus doesn't need to defer probing
>   of pinctrl driver if PMU has not yet been probed
> - collected Acks, minor fixes according to review comments

After fixing remaining nits in patch 1 and 10, for all pinctrl patches (4-13):

Acked-by: Tomasz Figa <tomasz.figa@gmail.com>

and for other patches (1-3):

Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>

Best regards,
Tomasz

Re: [PATCH v2 00/13] Move pad retention control to Exynos pin controller driver

[Linus Walleij]

On Tue, Jan 17, 2017 at 1:44 PM, Marek Szyprowski
<m.szyprowski@samsung.com> wrote:

> This patchset is a follow-up of my work on adding runtime PM support
> to Exynos pin controller driver:
> http://www.spinics.net/lists/arm-kernel/msg550161.html

Nice, once you are done fixing the remaining nits, add Tomasz ACKs
and resend as v3 and I will apply it.

Yours,
Linus Walleij

[PATCH v2 00/13] Move pad retention control to Exynos pin controller driver

[Linus Walleij]

On Tue, Jan 17, 2017 at 1:44 PM, Marek Szyprowski
<m.szyprowski@samsung.com> wrote:

> This patchset is a follow-up of my work on adding runtime PM support
> to Exynos pin controller driver:
> http://www.spinics.net/lists/arm-kernel/msg550161.html

Nice, once you are done fixing the remaining nits, add Tomasz ACKs
and resend as v3 and I will apply it.

Yours,
Linus Walleij

Re: [PATCH v2 00/13] Move pad retention control to Exynos pin controller driver

[Krzysztof Kozlowski]

On Wed, Jan 18, 2017 at 12:39 PM, Linus Walleij
<linus.walleij@linaro.org> wrote:
> On Tue, Jan 17, 2017 at 1:44 PM, Marek Szyprowski
> <m.szyprowski@samsung.com> wrote:
>
>> This patchset is a follow-up of my work on adding runtime PM support
>> to Exynos pin controller driver:
>> http://www.spinics.net/lists/arm-kernel/msg550161.html
>
> Nice, once you are done fixing the remaining nits, add Tomasz ACKs
> and resend as v3 and I will apply it.

Wait, for the pinctrl patches (and also the commits moving the bits
arch/arm -> pintrl) you need the soc changes (mostly: the header).
I'll prepare a tag with them but I am still giving some time for
review.

Best regards,
Krzysztof

[PATCH v2 00/13] Move pad retention control to Exynos pin controller driver

[Krzysztof Kozlowski]

On Wed, Jan 18, 2017 at 12:39 PM, Linus Walleij
<linus.walleij@linaro.org> wrote:
> On Tue, Jan 17, 2017 at 1:44 PM, Marek Szyprowski
> <m.szyprowski@samsung.com> wrote:
>
>> This patchset is a follow-up of my work on adding runtime PM support
>> to Exynos pin controller driver:
>> http://www.spinics.net/lists/arm-kernel/msg550161.html
>
> Nice, once you are done fixing the remaining nits, add Tomasz ACKs
> and resend as v3 and I will apply it.

Wait, for the pinctrl patches (and also the commits moving the bits
arch/arm -> pintrl) you need the soc changes (mostly: the header).
I'll prepare a tag with them but I am still giving some time for
review.

Best regards,
Krzysztof