[U-Boot] [PATCH 0/7] am57xx-idk LCD and am571x-idk 6 port ethernet pinmux

[U-Boot] [PATCH 0/7] am57xx-idk LCD and am571x-idk 6 port ethernet pinmux

[Roger Quadros]

Hi,

This series contains

- Support am571x-idk LCD vs 6 port ethernet pinmux configuration.
- AM57xx-idk LCD detection support
- K2G: pick up PRUSS ethernet MAC addresses from board EEPROM

cheers,
-roger

Lokesh Vutla (1):
  ti: common: board_detect: Rename EEPROM scratch start macro

Nishanth Menon (1):
  board: ti: am57xx-idk: Auto detect LCD Panel

Roger Quadros (5):
  ARM: OMAP5+: GPIO: Add GPIO_TO_PIN() macro
  ti: common: board_detect: commodify ethaddr environment setting code
  board: ti: am571x-idk: Support 6 port Ethernet or 4 port Ethernet with
    LCD
  board: ti: am571x-idk: Update pinmux for ICSS2 Ethernet
  ARM: k2g: setup PRU ethernet MAC addresses

 arch/arm/include/asm/arch-omap5/gpio.h |   4 +
 arch/arm/include/asm/omap_common.h     |   8 +-
 board/ti/am57xx/board.c                | 102 ++++++++++++++++++++
 board/ti/am57xx/mux_data.h             | 166 ++++++++++++++++++++-------------
 board/ti/common/board_detect.c         |  57 +++++++++++
 board/ti/common/board_detect.h         |  14 ++-
 board/ti/ks2_evm/board_k2g.c           |  19 ++++
 include/configs/k2g_evm.h              |   4 +
 include/configs/ti_omap5_common.h      |  14 ++-
 9 files changed, 315 insertions(+), 73 deletions(-)

-- 
2.7.4

[U-Boot] [PATCH 1/7] ARM: OMAP5+: GPIO: Add GPIO_TO_PIN() macro

[Roger Quadros]

GPIO_TO_PIN(bank, bank_gpio) returns the GPIO index
from the GPIO bank number and bank's GPIO offset number.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 arch/arm/include/asm/arch-omap5/gpio.h | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/include/asm/arch-omap5/gpio.h b/arch/arm/include/asm/arch-omap5/gpio.h
index 9dd03c9..48e8ca5 100644
--- a/arch/arm/include/asm/arch-omap5/gpio.h
+++ b/arch/arm/include/asm/arch-omap5/gpio.h
@@ -34,4 +34,8 @@
 #define OMAP54XX_GPIO7_BASE		0x48051000
 #define OMAP54XX_GPIO8_BASE		0x48053000
 
+
+/* Get the GPIO index from the given bank number and bank gpio */
+#define GPIO_TO_PIN(bank, bank_gpio)	(32 * (bank - 1) + (bank_gpio))
+
 #endif /* _GPIO_OMAP5_H */
-- 
2.7.4

[U-Boot] [PATCH 2/7] ti: common: board_detect: commodify ethaddr environment setting code

[Roger Quadros]

As Keystone platforms also need this let's move this function
to the common board_detect code.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 board/ti/common/board_detect.c | 57 ++++++++++++++++++++++++++++++++++++++++++
 board/ti/common/board_detect.h | 12 +++++++++
 2 files changed, 69 insertions(+)

diff --git a/board/ti/common/board_detect.c b/board/ti/common/board_detect.c
index a5dba94..40315e6 100644
--- a/board/ti/common/board_detect.c
+++ b/board/ti/common/board_detect.c
@@ -314,3 +314,60 @@ void __maybe_unused set_board_info_env(char *name)
 	else
 		setenv("board_serial", unknown);
 }
+
+static u64 mac_to_u64(u8 mac[6])
+{
+	int i;
+	u64 addr = 0;
+
+	for (i = 0; i < 6; i++) {
+		addr <<= 8;
+		addr |= mac[i];
+	}
+
+	return addr;
+}
+
+static void u64_to_mac(u64 addr, u8 mac[6])
+{
+	mac[5] = addr;
+	mac[4] = addr >> 8;
+	mac[3] = addr >> 16;
+	mac[2] = addr >> 24;
+	mac[1] = addr >> 32;
+	mac[0] = addr >> 40;
+}
+
+void __maybe_unused board_ti_set_ethaddr(int index)
+{
+	uint8_t mac_addr[6];
+	int i;
+	u64 mac1, mac2;
+	u8 mac_addr1[6], mac_addr2[6];
+	int num_macs;
+	/*
+	 * Export any Ethernet MAC addresses from EEPROM.
+	 * The 2 MAC addresses in EEPROM define the address range.
+	 */
+	board_ti_get_eth_mac_addr(0, mac_addr1);
+	board_ti_get_eth_mac_addr(1, mac_addr2);
+
+	if (is_valid_ethaddr(mac_addr1) && is_valid_ethaddr(mac_addr2)) {
+		mac1 = mac_to_u64(mac_addr1);
+		mac2 = mac_to_u64(mac_addr2);
+
+		/* must contain an address range */
+		num_macs = mac2 - mac1 + 1;
+		/* <= 50 to protect against user programming error */
+		if (num_macs > 0 && num_macs <= 50) {
+			for (i = 0; i < num_macs; i++) {
+				u64_to_mac(mac1 + i, mac_addr);
+				if (is_valid_ethaddr(mac_addr)) {
+					eth_setenv_enetaddr_by_index("eth",
+								     i + index,
+								     mac_addr);
+				}
+			}
+		}
+	}
+}
diff --git a/board/ti/common/board_detect.h b/board/ti/common/board_detect.h
index 343fcb4..fc15910 100644
--- a/board/ti/common/board_detect.h
+++ b/board/ti/common/board_detect.h
@@ -193,4 +193,16 @@ u64 board_ti_get_emif2_size(void);
  */
 void set_board_info_env(char *name);
 
+/**
+ * board_ti_set_ethaddr- Sets the ethaddr environment from EEPROM
+ * @index: The first eth<index>addr environment variable to set
+ *
+ * EEPROM should be already read before calling this function.
+ * The EEPROM contains 2 MAC addresses which define the MAC address
+ * range (i.e. first and last MAC address).
+ * This function sets the ethaddr environment variable for all
+ * the available MAC addresses starting from eth<index>addr.
+ */
+void __maybe_unused board_ti_set_ethaddr(int index);
+
 #endif	/* __BOARD_DETECT_H */
-- 
2.7.4

[U-Boot] [PATCH 3/7] board: ti: am571x-idk: Support 6 port Ethernet or 4 port Ethernet with LCD

[Roger Quadros]

The board can support either ICSS1 Ethernet ports or LCD
based on J51 jumper. Factory default is ICSS1 Ethernet ports
(i.e. Jumper not populated).

Use the GPIO to detect the jumper setting and configure the
pinmux accordingly. Also select the right DT blob based on
the chosen configuration.

J51 absent -> ICSS1 Ethernet, no LCD on VOUT -> am571x-idk.dtb
J51 present -> LCD on VOUT, no ICSS1 Ethernet -> am571x-idk-lcd-osd.dtb

At present we only support the assume it is the Legacy LCD.
LCD detection mechanism needs to be added later to differentiate
between legacy vs new LCD.

For ICSS1 Ethernet pins use the following convention to set the pinmux
as PMT data is not yet finalized.

- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
- Do not use SLEW_CONTROLon any pin.

[nm at ti.com] Fix wrong dtb selection caused by a typo ';'

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 board/ti/am57xx/board.c           |  40 +++++++++++++++
 board/ti/am57xx/mux_data.h        | 104 +++++++++++++++++++++++++-------------
 include/configs/ti_omap5_common.h |   4 +-
 3 files changed, 112 insertions(+), 36 deletions(-)

diff --git a/board/ti/am57xx/board.c b/board/ti/am57xx/board.c
index 5f2d4df..81ad86c 100644
--- a/board/ti/am57xx/board.c
+++ b/board/ti/am57xx/board.c
@@ -50,6 +50,7 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#define GPIO_ETH_LCD		GPIO_TO_PIN(2, 22)
 /* GPIO 7_11 */
 #define GPIO_DDR_VTT_EN 203
 
@@ -449,6 +450,21 @@ void hw_data_init(void)
 	*ctrl = &dra7xx_ctrl;
 }
 
+bool am571x_idk_needs_lcd(void)
+{
+	bool needs_lcd;
+
+	gpio_request(GPIO_ETH_LCD, "nLCD_Detect");
+	if (gpio_get_value(GPIO_ETH_LCD))
+		needs_lcd = false;
+	else
+		needs_lcd = true;
+
+	gpio_free(GPIO_ETH_LCD);
+
+	return needs_lcd;
+}
+
 int board_init(void)
 {
 	gpmc_init();
@@ -459,6 +475,8 @@ int board_init(void)
 
 int board_late_init(void)
 {
+	char *idk_lcd;
+
 	setup_board_eeprom_env();
 	u8 val;
 
@@ -487,6 +505,17 @@ int board_late_init(void)
 	palmas_i2c_write_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
 			    val);
 
+	/* TBD: Add LCD panel detection once information is available */
+	if (am571x_idk_needs_lcd())
+		idk_lcd = "osd101t2045"; /* Default to legacy LCD */
+	else
+		idk_lcd = "no";
+	setenv("idk_lcd", idk_lcd);
+
+#if !defined(CONFIG_SPL_BUILD)
+	board_ti_set_ethaddr(2);
+#endif
+
 	return 0;
 }
 
@@ -549,6 +578,17 @@ void recalibrate_iodelay(void)
 		do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz);
 	}
 
+	if (board_is_am571x_idk()) {
+		if (am571x_idk_needs_lcd()) {
+			pconf = core_padconf_array_vout_am571x_idk;
+			pconf_sz = ARRAY_SIZE(core_padconf_array_vout_am571x_idk);
+		} else {
+			pconf = core_padconf_array_icss1eth_am571x_idk;
+			pconf_sz = ARRAY_SIZE(core_padconf_array_icss1eth_am571x_idk);
+		}
+		do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz);
+	}
+
 	/* Setup IOdelay configuration */
 	ret = do_set_iodelay((*ctrl)->iodelay_config_base, iod, iod_sz);
 err:
diff --git a/board/ti/am57xx/mux_data.h b/board/ti/am57xx/mux_data.h
index 2f5243e..ff0e517 100644
--- a/board/ti/am57xx/mux_data.h
+++ b/board/ti/am57xx/mux_data.h
@@ -549,13 +549,6 @@ const struct pad_conf_entry core_padconf_array_essential_am571x_idk[] = {
 	{VIN2A_D0, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d0.pr1_uart0_rxd */
 	{VIN2A_D1, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d1.pr1_uart0_txd */
 	{VIN2A_D2, (M10 | PIN_INPUT_PULLDOWN)},	/* vin2a_d2.eCAP1_in_PWM1_out */
-	{VIN2A_D3, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d3.pr1_mi1_col */
-	{VIN2A_D4, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d4.pr1_mii1_txd1 */
-	{VIN2A_D5, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d5.pr1_mii1_txd0 */
-	{VIN2A_D6, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d6.pr1_mii_mt1_clk */
-	{VIN2A_D7, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d7.pr1_mii1_txen */
-	{VIN2A_D8, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d8.pr1_mii1_txd3 */
-	{VIN2A_D9, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d9.pr1_mii1_txd2 */
 	{VIN2A_D10, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d10.pr1_mdio_mdclk */
 	{VIN2A_D11, (M11 | PIN_INPUT_PULLUP)},	/* vin2a_d11.pr1_mdio_data */
 	{VIN2A_D12, (M3 | PIN_INPUT_PULLDOWN | MANUAL_MODE)},	/* vin2a_d12.rgmii1_txc */
@@ -570,35 +563,7 @@ const struct pad_conf_entry core_padconf_array_essential_am571x_idk[] = {
 	{VIN2A_D21, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* vin2a_d21.rgmii1_rxd2 */
 	{VIN2A_D22, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* vin2a_d22.rgmii1_rxd1 */
 	{VIN2A_D23, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* vin2a_d23.rgmii1_rxd0 */
-	{VOUT1_CLK, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_clk.vout1_clk */
-	{VOUT1_DE, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_de.vout1_de */
 	{VOUT1_FLD, (M14 | PIN_INPUT_PULLUP)},	/* vout1_fld.gpio4_21 */
-	{VOUT1_HSYNC, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_hsync.vout1_hsync */
-	{VOUT1_VSYNC, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_vsync.vout1_vsync */
-	{VOUT1_D0, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d0.vout1_d0 */
-	{VOUT1_D1, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d1.vout1_d1 */
-	{VOUT1_D2, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d2.vout1_d2 */
-	{VOUT1_D3, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d3.vout1_d3 */
-	{VOUT1_D4, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d4.vout1_d4 */
-	{VOUT1_D5, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d5.vout1_d5 */
-	{VOUT1_D6, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d6.vout1_d6 */
-	{VOUT1_D7, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d7.vout1_d7 */
-	{VOUT1_D8, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d8.vout1_d8 */
-	{VOUT1_D9, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d9.vout1_d9 */
-	{VOUT1_D10, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d10.vout1_d10 */
-	{VOUT1_D11, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d11.vout1_d11 */
-	{VOUT1_D12, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d12.vout1_d12 */
-	{VOUT1_D13, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d13.vout1_d13 */
-	{VOUT1_D14, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d14.vout1_d14 */
-	{VOUT1_D15, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d15.vout1_d15 */
-	{VOUT1_D16, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d16.vout1_d16 */
-	{VOUT1_D17, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d17.vout1_d17 */
-	{VOUT1_D18, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d18.vout1_d18 */
-	{VOUT1_D19, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d19.vout1_d19 */
-	{VOUT1_D20, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d20.vout1_d20 */
-	{VOUT1_D21, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d21.vout1_d21 */
-	{VOUT1_D22, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d22.vout1_d22 */
-	{VOUT1_D23, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d23.vout1_d23 */
 	{MDIO_MCLK, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/* mdio_mclk.mdio_mclk */
 	{MDIO_D, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/* mdio_d.mdio_d */
 	{RMII_MHZ_50_CLK, (M13 | PIN_INPUT_PULLDOWN)},	/* RMII_MHZ_50_CLK.pr2_pru1_gpo2 */
@@ -727,6 +692,75 @@ const struct pad_conf_entry core_padconf_array_essential_am571x_idk[] = {
 	{RSTOUTN, (M0 | PIN_OUTPUT_PULLDOWN)},	/* rstoutn.rstoutn */
 };
 
+const struct pad_conf_entry core_padconf_array_icss1eth_am571x_idk[] = {
+	/* PR1 MII0 */
+	{VOUT1_D8, (M12 | PIN_INPUT_PULLDOWN)},	/* vout1_d8.pr1_mii_mt0_clk */
+	{VOUT1_D9, (M13 | PIN_OUTPUT)},		/* vout1_d9.pr1_mii0_txd3 */
+	{VOUT1_D10, (M13 | PIN_OUTPUT)},	/* vout1_d10.pr1_mii0_txd2 */
+	{VOUT1_D11, (M13 | PIN_OUTPUT)},	/* vout1_d11.pr1_mii0_txen */
+	{VOUT1_D12, (M13 | PIN_OUTPUT)},	/* vout1_d12.pr1_mii0_txd1 */
+	{VOUT1_D13, (M13 | PIN_OUTPUT)},	/* vout1_d13.pr1_mii0_txd0 */
+	{VOUT1_D14, (M12 | PIN_INPUT_PULLDOWN)},	/* vout1_d14.pr1_mii_mr0_clk */
+	{VOUT1_D15, (M12 | PIN_INPUT_PULLDOWN)},	/* vout1_d15.pr1_mii0_rxdv */
+	{VOUT1_D16, (M12 | PIN_INPUT)},	/* vout1_d16.pr1_mii0_rxd3 */
+	{VOUT1_D17, (M12 | PIN_INPUT)},	/* vout1_d17.pr1_mii0_rxd2 */
+	{VOUT1_D18, (M12 | PIN_INPUT)},	/* vout1_d18.pr1_mii0_rxd1 */
+	{VOUT1_D19, (M12 | PIN_INPUT)},	/* vout1_d19.pr1_mii0_rxd0 */
+	{VOUT1_D20, (M12 | PIN_INPUT_PULLUP)},	/* vout1_d20.pr1_mii0_rxer */
+	{VOUT1_D21, (M12 | PIN_INPUT)},	/* vout1_d21.pr1_mii0_rxlink */
+	{VOUT1_D22, (M12 | PIN_INPUT)},	/* vout1_d22.pr1_mii0_col */
+	{VOUT1_D23, (M12 | PIN_INPUT_PULLUP)},	/* vout1_d23.pr1_mii0_crs */
+
+	/* PR1 MII1 */
+	{VIN2A_D3, (M12 | PIN_INPUT)},	/* vin2a_d3.pr1_mi1_col */
+	{VIN2A_D4, (M13 | PIN_OUTPUT)},	/* vin2a_d4.pr1_mii1_txd1 */
+	{VIN2A_D5, (M13 | PIN_OUTPUT)},	/* vin2a_d5.pr1_mii1_txd0 */
+	{VIN2A_D6, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d6.pr1_mii_mt1_clk */
+	{VIN2A_D7, (M11 | PIN_OUTPUT)},	/* vin2a_d7.pr1_mii1_txen */
+	{VIN2A_D8, (M11 | PIN_OUTPUT)},	/* vin2a_d8.pr1_mii1_txd3 */
+	{VIN2A_D9, (M11 | PIN_OUTPUT)},	/* vin2a_d9.pr1_mii1_txd2 */
+	{VOUT1_VSYNC, (M12 | PIN_INPUT_PULLUP)},	/* vout1_vsync.pr1_mii1_rxer */
+	{VOUT1_D0, (M12 | PIN_INPUT)},	/* vout1_d0.pr1_mii1_rxlink */
+	{VOUT1_D1, (M12 | PIN_INPUT_PULLUP)},	/* vout1_d1.pr1_mii1_crs */
+	{VOUT1_D2, (M12 | PIN_INPUT_PULLDOWN)},	/* vout1_d2.pr1_mii_mr1_clk */
+	{VOUT1_D3, (M12 | PIN_INPUT_PULLDOWN)},	/* vout1_d3.pr1_mii1_rxdv */
+	{VOUT1_D4, (M12 | PIN_INPUT)},	/* vout1_d4.pr1_mii1_rxd3 */
+	{VOUT1_D5, (M12 | PIN_INPUT)},	/* vout1_d5.pr1_mii1_rxd2 */
+	{VOUT1_D6, (M12 | PIN_INPUT)},	/* vout1_d6.pr1_mii1_rxd1 */
+	{VOUT1_D7, (M12 | PIN_INPUT)},	/* vout1_d7.pr1_mii1_rxd0 */
+};
+
+const struct pad_conf_entry core_padconf_array_vout_am571x_idk[] = {
+	{VOUT1_CLK, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_clk.vout1_clk */
+	{VOUT1_DE, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_de.vout1_de */
+	{VOUT1_HSYNC, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_hsync.vout1_hsync */
+	{VOUT1_VSYNC, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_vsync.vout1_vsync */
+	{VOUT1_D0, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d0.vout1_d0 */
+	{VOUT1_D1, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d1.vout1_d1 */
+	{VOUT1_D2, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d2.vout1_d2 */
+	{VOUT1_D3, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d3.vout1_d3 */
+	{VOUT1_D4, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d4.vout1_d4 */
+	{VOUT1_D5, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d5.vout1_d5 */
+	{VOUT1_D6, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d6.vout1_d6 */
+	{VOUT1_D7, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d7.vout1_d7 */
+	{VOUT1_D8, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d8.vout1_d8 */
+	{VOUT1_D9, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d9.vout1_d9 */
+	{VOUT1_D10, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d10.vout1_d10 */
+	{VOUT1_D11, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d11.vout1_d11 */
+	{VOUT1_D12, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d12.vout1_d12 */
+	{VOUT1_D13, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d13.vout1_d13 */
+	{VOUT1_D14, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d14.vout1_d14 */
+	{VOUT1_D15, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d15.vout1_d15 */
+	{VOUT1_D16, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d16.vout1_d16 */
+	{VOUT1_D17, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d17.vout1_d17 */
+	{VOUT1_D18, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d18.vout1_d18 */
+	{VOUT1_D19, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d19.vout1_d19 */
+	{VOUT1_D20, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d20.vout1_d20 */
+	{VOUT1_D21, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d21.vout1_d21 */
+	{VOUT1_D22, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d22.vout1_d22 */
+	{VOUT1_D23, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d23.vout1_d23 */
+};
+
 const struct pad_conf_entry early_padconf[] = {
 	{UART2_CTSN, (M2 | PIN_INPUT_SLEW)},	/* uart2_ctsn.uart3_rxd */
 	{UART2_RTSN, (M1 | PIN_INPUT_SLEW)},	/* uart2_rtsn.uart3_txd */
diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h
index 37d6565..6de19c2 100644
--- a/include/configs/ti_omap5_common.h
+++ b/include/configs/ti_omap5_common.h
@@ -97,8 +97,10 @@
 			"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
 		"if test $board_name = am57xx_evm_reva3; then " \
 			"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
-		"if test $board_name = am571x_idk; then " \
+		"if test $board_name = am571x_idk && test $idk_lcd = no; then " \
 			"setenv fdtfile am571x-idk.dtb; fi;" \
+		"if test $board_name = am571x_idk && test $idk_lcd = osd101t2045; then " \
+			"setenv fdtfile am571x-idk-lcd-osd.dtb; fi;" \
 		"if test $fdtfile = undefined; then " \
 			"echo WARNING: Could not determine device tree to use; fi; \0" \
 	DFUARGS \
-- 
2.7.4

[U-Boot] [PATCH 4/7] board: ti: am571x-idk: Update pinmux for ICSS2 Ethernet

[Roger Quadros]

Use the same convention that was used for ICSS1 Ethernet
- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 board/ti/am57xx/mux_data.h | 62 +++++++++++++++++++++++-----------------------
 1 file changed, 31 insertions(+), 31 deletions(-)

diff --git a/board/ti/am57xx/mux_data.h b/board/ti/am57xx/mux_data.h
index ff0e517..5485212 100644
--- a/board/ti/am57xx/mux_data.h
+++ b/board/ti/am57xx/mux_data.h
@@ -586,46 +586,46 @@ const struct pad_conf_entry core_padconf_array_essential_am571x_idk[] = {
 	{GPIO6_14, (M14 | PIN_INPUT_PULLUP)},	/* gpio6_14.gpio6_14 */
 	{GPIO6_15, (M14 | PIN_INPUT_PULLUP)},	/* gpio6_15.gpio6_15 */
 	{GPIO6_16, (M14 | PIN_INPUT_PULLDOWN)},	/* gpio6_16.gpio6_16 */
-	{XREF_CLK0, (M11 | PIN_INPUT_PULLDOWN)},	/* xref_clk0.pr2_mii1_col */
-	{XREF_CLK1, (M11 | PIN_INPUT_PULLDOWN)},	/* xref_clk1.pr2_mii1_crs */
+	{XREF_CLK0, (M11 | PIN_INPUT)},	/* xref_clk0.pr2_mii1_col */
+	{XREF_CLK1, (M11 | PIN_INPUT_PULLUP)},	/* xref_clk1.pr2_mii1_crs */
 	{XREF_CLK2, (M14 | PIN_INPUT_PULLDOWN)},	/* xref_clk2.gpio6_19 */
 	{XREF_CLK3, (M15 | PIN_INPUT_PULLDOWN)},	/* xref_clk3.Driveroff */
 	{MCASP1_ACLKX, (M11 | PIN_INPUT_PULLDOWN)},	/* mcasp1_aclkx.pr2_mdio_mdclk */
 	{MCASP1_FSX, (M11 | PIN_INPUT_SLEW)},	/* mcasp1_fsx.pr2_mdio_data */
 	{MCASP1_ACLKR, (M14 | PIN_INPUT_PULLUP)},	/* mcasp1_aclkr.gpio5_0 */
 	{MCASP1_FSR, (M14 | PIN_INPUT_PULLUP)},	/* mcasp1_fsr.gpio5_1 */
-	{MCASP1_AXR0, (M11 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/* mcasp1_axr0.pr2_mii0_rxer */
-	{MCASP1_AXR1, (M11 | PIN_INPUT_SLEW)},	/* mcasp1_axr1.pr2_mii_mt0_clk */
+	{MCASP1_AXR0, (M11 | PIN_INPUT_PULLUP)},	/* mcasp1_axr0.pr2_mii0_rxer */
+	{MCASP1_AXR1, (M11 | PIN_INPUT_PULLDOWN)},	/* mcasp1_axr1.pr2_mii_mt0_clk */
 	{MCASP1_AXR2, (M14 | PIN_INPUT_PULLDOWN)},	/* mcasp1_axr2.gpio5_4 */
 	{MCASP1_AXR3, (M14 | PIN_INPUT_PULLUP)},	/* mcasp1_axr3.gpio5_5 */
 	{MCASP1_AXR4, (M14 | PIN_INPUT_PULLDOWN)},	/* mcasp1_axr4.gpio5_6 */
 	{MCASP1_AXR5, (M14 | PIN_INPUT_PULLDOWN)},	/* mcasp1_axr5.gpio5_7 */
 	{MCASP1_AXR6, (M14 | PIN_INPUT_PULLUP)},	/* mcasp1_axr6.gpio5_8 */
 	{MCASP1_AXR7, (M14 | PIN_INPUT_PULLUP)},	/* mcasp1_axr7.gpio5_9 */
-	{MCASP1_AXR8, (M11 | PIN_INPUT_SLEW)},	/* mcasp1_axr8.pr2_mii0_txen */
-	{MCASP1_AXR9, (M11 | PIN_INPUT_SLEW)},	/* mcasp1_axr9.pr2_mii0_txd3 */
-	{MCASP1_AXR10, (M11 | PIN_INPUT_SLEW)},	/* mcasp1_axr10.pr2_mii0_txd2 */
-	{MCASP1_AXR11, (M11 | PIN_INPUT_SLEW)},	/* mcasp1_axr11.pr2_mii0_txd1 */
-	{MCASP1_AXR12, (M11 | PIN_INPUT_SLEW)},	/* mcasp1_axr12.pr2_mii0_txd0 */
-	{MCASP1_AXR13, (M11 | PIN_INPUT_SLEW)},	/* mcasp1_axr13.pr2_mii_mr0_clk */
-	{MCASP1_AXR14, (M11 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* mcasp1_axr14.pr2_mii0_rxdv */
-	{MCASP1_AXR15, (M11 | PIN_INPUT_SLEW)},	/* mcasp1_axr15.pr2_mii0_rxd3 */
-	{MCASP2_ACLKX, (M11 | PIN_INPUT_SLEW)},	/* mcasp2_aclkx.pr2_mii0_rxd2 */
-	{MCASP2_FSX, (M11 | PIN_INPUT_SLEW)},	/* mcasp2_fsx.pr2_mii0_rxd1 */
+	{MCASP1_AXR8, (M11 | PIN_OUTPUT)},	/* mcasp1_axr8.pr2_mii0_txen */
+	{MCASP1_AXR9, (M11 | PIN_OUTPUT)},	/* mcasp1_axr9.pr2_mii0_txd3 */
+	{MCASP1_AXR10, (M11 | PIN_OUTPUT)},	/* mcasp1_axr10.pr2_mii0_txd2 */
+	{MCASP1_AXR11, (M11 | PIN_OUTPUT)},	/* mcasp1_axr11.pr2_mii0_txd1 */
+	{MCASP1_AXR12, (M11 | PIN_OUTPUT)},	/* mcasp1_axr12.pr2_mii0_txd0 */
+	{MCASP1_AXR13, (M11 | PIN_INPUT_PULLDOWN)},	/* mcasp1_axr13.pr2_mii_mr0_clk */
+	{MCASP1_AXR14, (M11 | PIN_INPUT_PULLDOWN)},	/* mcasp1_axr14.pr2_mii0_rxdv */
+	{MCASP1_AXR15, (M11 | PIN_INPUT)},	/* mcasp1_axr15.pr2_mii0_rxd3 */
+	{MCASP2_ACLKX, (M11 | PIN_INPUT)},	/* mcasp2_aclkx.pr2_mii0_rxd2 */
+	{MCASP2_FSX, (M11 | PIN_INPUT)},	/* mcasp2_fsx.pr2_mii0_rxd1 */
 	{MCASP2_ACLKR, (M15 | PIN_INPUT_PULLDOWN)},	/* mcasp2_aclkr.Driveroff */
 	{MCASP2_FSR, (M15 | PIN_INPUT_PULLDOWN)},	/* mcasp2_fsr.Driveroff */
 	{MCASP2_AXR0, (M15 | PIN_INPUT_PULLDOWN)},	/* mcasp2_axr0.Driveroff */
 	{MCASP2_AXR1, (M15 | PIN_INPUT_PULLDOWN)},	/* mcasp2_axr1.Driveroff */
-	{MCASP2_AXR2, (M11 | PIN_INPUT_SLEW)},	/* mcasp2_axr2.pr2_mii0_rxd0 */
-	{MCASP2_AXR3, (M11 | PIN_INPUT_PULLDOWN | SLEWCONTROL)},	/* mcasp2_axr3.pr2_mii0_rxlink */
+	{MCASP2_AXR2, (M11 | PIN_INPUT)},	/* mcasp2_axr2.pr2_mii0_rxd0 */
+	{MCASP2_AXR3, (M11 | PIN_INPUT)},	/* mcasp2_axr3.pr2_mii0_rxlink */
 	{MCASP2_AXR4, (M14 | PIN_INPUT_PULLDOWN)},	/* mcasp2_axr4.gpio1_4 */
 	{MCASP2_AXR5, (M14 | PIN_INPUT_PULLDOWN)},	/* mcasp2_axr5.gpio6_7 */
 	{MCASP2_AXR6, (M14 | PIN_INPUT_PULLDOWN)},	/* mcasp2_axr6.gpio2_29 */
 	{MCASP2_AXR7, (M14 | PIN_INPUT_PULLDOWN)},	/* mcasp2_axr7.gpio1_5 */
-	{MCASP3_ACLKX, (M11 | PIN_INPUT_PULLDOWN)},	/* mcasp3_aclkx.pr2_mii0_crs */
-	{MCASP3_FSX, (M11 | PIN_INPUT_SLEW)},	/* mcasp3_fsx.pr2_mii0_col */
-	{MCASP3_AXR0, (M11 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/* mcasp3_axr0.pr2_mii1_rxer */
-	{MCASP3_AXR1, (M11 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/* mcasp3_axr1.pr2_mii1_rxlink */
+	{MCASP3_ACLKX, (M11 | PIN_INPUT_PULLUP)},	/* mcasp3_aclkx.pr2_mii0_crs */
+	{MCASP3_FSX, (M11 | PIN_INPUT)},	/* mcasp3_fsx.pr2_mii0_col */
+	{MCASP3_AXR0, (M11 | PIN_INPUT_PULLUP)},	/* mcasp3_axr0.pr2_mii1_rxer */
+	{MCASP3_AXR1, (M11 | PIN_INPUT)},	/* mcasp3_axr1.pr2_mii1_rxlink */
 	{MCASP4_ACLKX, (M2 | PIN_INPUT_PULLDOWN)},	/* mcasp4_aclkx.spi3_sclk */
 	{MCASP4_FSX, (M2 | PIN_INPUT_PULLDOWN)},	/* mcasp4_fsx.spi3_d1 */
 	{MCASP4_AXR0, (M15 | PIN_INPUT_PULLDOWN)},	/* mcasp4_axr0.Driveroff */
@@ -642,18 +642,18 @@ const struct pad_conf_entry core_padconf_array_essential_am571x_idk[] = {
 	{MMC1_DAT3, (M0 | PIN_INPUT_PULLUP)},	/* mmc1_dat3.mmc1_dat3 */
 	{MMC1_SDCD, (M14 | PIN_INPUT_PULLUP)},	/* mmc1_sdcd.gpio6_27 */
 	{MMC1_SDWP, (M0 | PIN_OUTPUT)},	/* mmc1_sdwp.mmc1_sdwp */
-	{GPIO6_10, (M11 | PIN_INPUT_PULLUP)},	/* gpio6_10.pr2_mii_mt1_clk */
-	{GPIO6_11, (M11 | PIN_INPUT_PULLUP)},	/* gpio6_11.pr2_mii1_txen */
-	{MMC3_CLK, (M11 | PIN_INPUT_PULLUP)},	/* mmc3_clk.pr2_mii1_txd3 */
-	{MMC3_CMD, (M11 | PIN_INPUT_PULLUP)},	/* mmc3_cmd.pr2_mii1_txd2 */
-	{MMC3_DAT0, (M11 | PIN_INPUT_PULLUP)},	/* mmc3_dat0.pr2_mii1_txd1 */
-	{MMC3_DAT1, (M11 | PIN_INPUT_PULLUP)},	/* mmc3_dat1.pr2_mii1_txd0 */
-	{MMC3_DAT2, (M11 | PIN_INPUT_PULLUP)},	/* mmc3_dat2.pr2_mii_mr1_clk */
+	{GPIO6_10, (M11 | PIN_INPUT_PULLDOWN)},	/* gpio6_10.pr2_mii_mt1_clk */
+	{GPIO6_11, (M11 | PIN_OUTPUT)},	/* gpio6_11.pr2_mii1_txen */
+	{MMC3_CLK, (M11 | PIN_OUTPUT)},	/* mmc3_clk.pr2_mii1_txd3 */
+	{MMC3_CMD, (M11 | PIN_OUTPUT)},	/* mmc3_cmd.pr2_mii1_txd2 */
+	{MMC3_DAT0, (M11 | PIN_OUTPUT)},	/* mmc3_dat0.pr2_mii1_txd1 */
+	{MMC3_DAT1, (M11 | PIN_OUTPUT)},	/* mmc3_dat1.pr2_mii1_txd0 */
+	{MMC3_DAT2, (M11 | PIN_INPUT_PULLDOWN)},	/* mmc3_dat2.pr2_mii_mr1_clk */
 	{MMC3_DAT3, (M11 | PIN_INPUT_PULLDOWN)},	/* mmc3_dat3.pr2_mii1_rxdv */
-	{MMC3_DAT4, (M11 | PIN_INPUT_PULLDOWN)},	/* mmc3_dat4.pr2_mii1_rxd3 */
-	{MMC3_DAT5, (M11 | PIN_INPUT_PULLDOWN)},	/* mmc3_dat5.pr2_mii1_rxd2 */
-	{MMC3_DAT6, (M11 | PIN_INPUT_PULLDOWN)},	/* mmc3_dat6.pr2_mii1_rxd1 */
-	{MMC3_DAT7, (M11 | PIN_INPUT_PULLDOWN)},	/* mmc3_dat7.pr2_mii1_rxd0 */
+	{MMC3_DAT4, (M11 | PIN_INPUT)},	/* mmc3_dat4.pr2_mii1_rxd3 */
+	{MMC3_DAT5, (M11 | PIN_INPUT)},	/* mmc3_dat5.pr2_mii1_rxd2 */
+	{MMC3_DAT6, (M11 | PIN_INPUT)},	/* mmc3_dat6.pr2_mii1_rxd1 */
+	{MMC3_DAT7, (M11 | PIN_INPUT)},	/* mmc3_dat7.pr2_mii1_rxd0 */
 	{SPI1_SCLK, (M14 | PIN_INPUT_PULLDOWN)},	/* spi1_sclk.gpio7_7 */
 	{SPI1_D1, (M14 | PIN_INPUT_PULLDOWN)},	/* spi1_d1.gpio7_8 */
 	{SPI1_D0, (M14 | PIN_INPUT_PULLDOWN)},	/* spi1_d0.gpio7_9 */
-- 
2.7.4

[U-Boot] [PATCH 5/7] board: ti: am57xx-idk: Auto detect LCD Panel

[Roger Quadros]

From: Nishanth Menon <nm@ti.com>

AM571x IDK and AM572x IDK have optional LCD Kits that can be purchased.
These can be one of OSD101T2045 or the newer OSD101T2587. The LCD panel
itself has no registers that can be used to identify the panel, however,
the touchscreen controllers on the panels are different.

Hence to ease user experience, we can use the touch screen controller's
ID information to detect what kind of panel we use and select the
appropriate kernel dtb for the platform configuration.

NOTE: AM572x IDK default configuration is for LCD Connectivity, however
the AM571x IDK has a jumper (J51) that needs to be mounted for the IDK
to operate with LCD (Vs two PRUSS ethernet port option).

Touchscreen ID information is documented in:
http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf

Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 board/ti/am57xx/board.c           | 78 +++++++++++++++++++++++++++++++++++----
 include/configs/ti_omap5_common.h | 10 ++++-
 2 files changed, 78 insertions(+), 10 deletions(-)

diff --git a/board/ti/am57xx/board.c b/board/ti/am57xx/board.c
index 81ad86c..9ec0448 100644
--- a/board/ti/am57xx/board.c
+++ b/board/ti/am57xx/board.c
@@ -54,6 +54,19 @@ DECLARE_GLOBAL_DATA_PTR;
 /* GPIO 7_11 */
 #define GPIO_DDR_VTT_EN 203
 
+/* Touch screen controller to identify the LCD */
+#define OSD_TS_FT_BUS_ADDRESS	0
+#define OSD_TS_FT_CHIP_ADDRESS	0x38
+#define OSD_TS_FT_REG_ID	0xA3
+/*
+ * Touchscreen IDs for various OSD panels
+ * Ref: http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf
+ */
+/* Used on newer osd101t2587 Panels */
+#define OSD_TS_FT_ID_5x46	0x54
+/* Used on older osd101t2045 Panels */
+#define OSD_TS_FT_ID_5606	0x08
+
 #define SYSINFO_BOARD_NAME_MAX_LEN	45
 
 #define TPS65903X_PRIMARY_SECONDARY_PAD2	0xFB
@@ -473,10 +486,64 @@ int board_init(void)
 	return 0;
 }
 
-int board_late_init(void)
+void am57x_idk_lcd_detect(void)
 {
-	char *idk_lcd;
+	int r = -ENODEV;
+	char *idk_lcd = "no";
+	uint8_t buf = 0;
+
+	/* Only valid for IDKs */
+	if (board_is_x15() || board_is_am572x_evm())
+		return;
+
+	/* Only AM571x IDK has gpio control detect.. so check that */
+	if (board_is_am571x_idk() && !am571x_idk_needs_lcd())
+		goto out;
+
+	r = i2c_set_bus_num(OSD_TS_FT_BUS_ADDRESS);
+	if (r) {
+		printf("%s: Failed to set bus address to %d: %d\n",
+		       __func__, OSD_TS_FT_BUS_ADDRESS, r);
+		goto out;
+	}
+	r = i2c_probe(OSD_TS_FT_CHIP_ADDRESS);
+	if (r) {
+		/* AM572x IDK has no explicit settings for optional LCD kit */
+		if (board_is_am571x_idk()) {
+			printf("%s: Touch screen detect failed: %d!\n",
+			       __func__, r);
+		}
+		goto out;
+	}
+
+	/* Read FT ID */
+	r = i2c_read(OSD_TS_FT_CHIP_ADDRESS, OSD_TS_FT_REG_ID, 1, &buf, 1);
+	if (r) {
+		printf("%s: Touch screen ID read %d:0x%02x[0x%02x] failed:%d\n",
+		       __func__, OSD_TS_FT_BUS_ADDRESS, OSD_TS_FT_CHIP_ADDRESS,
+		       OSD_TS_FT_REG_ID, r);
+		goto out;
+	}
+
+	switch (buf) {
+	case OSD_TS_FT_ID_5606:
+		idk_lcd = "osd101t2045";
+		break;
+	case OSD_TS_FT_ID_5x46:
+		idk_lcd = "osd101t2587";
+		break;
+	default:
+		printf("%s: Unidentifed Touch screen ID 0x%02x\n",
+		       __func__, buf);
+		/* we will let default be "no lcd" */
+	}
+out:
+	setenv("idk_lcd", idk_lcd);
+	return;
+}
 
+int board_late_init(void)
+{
 	setup_board_eeprom_env();
 	u8 val;
 
@@ -505,12 +572,7 @@ int board_late_init(void)
 	palmas_i2c_write_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
 			    val);
 
-	/* TBD: Add LCD panel detection once information is available */
-	if (am571x_idk_needs_lcd())
-		idk_lcd = "osd101t2045"; /* Default to legacy LCD */
-	else
-		idk_lcd = "no";
-	setenv("idk_lcd", idk_lcd);
+	am57x_idk_lcd_detect();
 
 #if !defined(CONFIG_SPL_BUILD)
 	board_ti_set_ethaddr(2);
diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h
index 6de19c2..1fa2f82 100644
--- a/include/configs/ti_omap5_common.h
+++ b/include/configs/ti_omap5_common.h
@@ -91,16 +91,22 @@
 			"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
 		"if test $board_name = beagle_x15_revb1; then " \
 			"setenv fdtfile am57xx-beagle-x15-revb1.dtb; fi;" \
-		"if test $board_name = am572x_idk; then " \
-			"setenv fdtfile am572x-idk.dtb; fi;" \
 		"if test $board_name = am57xx_evm; then " \
 			"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
 		"if test $board_name = am57xx_evm_reva3; then " \
 			"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
+		"if test $board_name = am572x_idk && test $idk_lcd = no; then " \
+			"setenv fdtfile am572x-idk.dtb; fi;" \
+		"if test $board_name = am572x_idk && test $idk_lcd = osd101t2045; then " \
+			"setenv fdtfile am572x-idk-lcd-osd.dtb; fi;" \
+		"if test $board_name = am572x_idk && test $idk_lcd = osd101t2587; then " \
+			"setenv fdtfile am572x-idk-lcd-osd101t2587.dtb; fi;" \
 		"if test $board_name = am571x_idk && test $idk_lcd = no; then " \
 			"setenv fdtfile am571x-idk.dtb; fi;" \
 		"if test $board_name = am571x_idk && test $idk_lcd = osd101t2045; then " \
 			"setenv fdtfile am571x-idk-lcd-osd.dtb; fi;" \
+		"if test $board_name = am571x_idk && test $idk_lcd = osd101t2587; then " \
+			"setenv fdtfile am571x-idk-lcd-osd101t2587.dtb; fi;" \
 		"if test $fdtfile = undefined; then " \
 			"echo WARNING: Could not determine device tree to use; fi; \0" \
 	DFUARGS \
-- 
2.7.4

[U-Boot] [PATCH 6/7] ARM: k2g: setup PRU ethernet MAC addresses

[Roger Quadros]

PRU ethernet MAC address range is present in the
board EEPROM. Parse it and setup eth?addr
environment variables.

Signed-off-by: Roger Quadros <rogerq@ti.com>
---
 board/ti/ks2_evm/board_k2g.c | 19 +++++++++++++++++++
 include/configs/k2g_evm.h    |  4 ++++
 2 files changed, 23 insertions(+)

diff --git a/board/ti/ks2_evm/board_k2g.c b/board/ti/ks2_evm/board_k2g.c
index 40edbaa..64a62e0 100644
--- a/board/ti/ks2_evm/board_k2g.c
+++ b/board/ti/ks2_evm/board_k2g.c
@@ -12,6 +12,7 @@
 #include <asm/arch/psc_defs.h>
 #include <asm/arch/mmc_host_def.h>
 #include "mux-k2g.h"
+#include "../common/board_detect.h"
 
 #define SYS_CLK		24000000
 
@@ -149,6 +150,24 @@ int board_early_init_f(void)
 }
 #endif
 
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+	__maybe_unused int rc;
+
+#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_TI_I2C_BOARD_DETECT)
+	rc = ti_i2c_eeprom_am_get(CONFIG_EEPROM_BUS_ADDRESS,
+			CONFIG_EEPROM_CHIP_ADDRESS);
+	if (rc)
+		printf("ti_i2c_eeprom_init failed %d\n", rc);
+
+	board_ti_set_ethaddr(1);
+#endif
+
+	return 0;
+}
+#endif
+
 #ifdef CONFIG_SPL_BUILD
 void spl_init_keystone_plls(void)
 {
diff --git a/include/configs/k2g_evm.h b/include/configs/k2g_evm.h
index 81da8ff..f37dbfd 100644
--- a/include/configs/k2g_evm.h
+++ b/include/configs/k2g_evm.h
@@ -53,6 +53,10 @@
 /* NAND Configuration */
 #define CONFIG_SYS_NAND_PAGE_2K
 
+/* Board Detection EEPROM */
+#define CONFIG_EEPROM_BUS_ADDRESS	0
+#define CONFIG_EEPROM_CHIP_ADDRESS	0x50
+
 /* Network */
 #define CONFIG_KSNET_NETCP_V1_5
 #define CONFIG_KSNET_CPSW_NUM_PORTS	2
-- 
2.7.4

[U-Boot] [PATCH 7/7] ti: common: board_detect: Rename EEPROM scratch start macro

[Roger Quadros]

From: Lokesh Vutla <lokeshvutla@ti.com>

Non OMAP platforms i.e. Keystone will also need to use the board
EEPROM helpers so let's make the macro platform independent.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 arch/arm/include/asm/omap_common.h | 8 +++++---
 board/ti/common/board_detect.h     | 2 +-
 2 files changed, 6 insertions(+), 4 deletions(-)

diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h
index 2034a5e..c1a70b1 100644
--- a/arch/arm/include/asm/omap_common.h
+++ b/arch/arm/include/asm/omap_common.h
@@ -767,9 +767,11 @@ static inline u8 is_dra72x(void)
 #define OMAP_SRAM_SCRATCH_VCORES_PTR    (SRAM_SCRATCH_SPACE_ADDR + 0x1C)
 #define OMAP_SRAM_SCRATCH_SYS_CTRL	(SRAM_SCRATCH_SPACE_ADDR + 0x20)
 #define OMAP_SRAM_SCRATCH_BOOT_PARAMS	(SRAM_SCRATCH_SPACE_ADDR + 0x24)
-#define OMAP_SRAM_SCRATCH_BOARD_EEPROM_START (SRAM_SCRATCH_SPACE_ADDR + 0x28)
-#define OMAP_SRAM_SCRATCH_BOARD_EEPROM_END (SRAM_SCRATCH_SPACE_ADDR + 0x200)
-#define OMAP_SRAM_SCRATCH_SPACE_END	(OMAP_SRAM_SCRATCH_BOARD_EEPROM_END)
+#ifndef TI_SRAM_SCRATCH_BOARD_EEPROM_START
+#define TI_SRAM_SCRATCH_BOARD_EEPROM_START (SRAM_SCRATCH_SPACE_ADDR + 0x28)
+#define TI_SRAM_SCRATCH_BOARD_EEPROM_END (SRAM_SCRATCH_SPACE_ADDR + 0x200)
+#endif
+#define OMAP_SRAM_SCRATCH_SPACE_END	(TI_SRAM_SCRATCH_BOARD_EEPROM_END)
 
 /* Boot parameters */
 #define DEVICE_DATA_OFFSET	0x18
diff --git a/board/ti/common/board_detect.h b/board/ti/common/board_detect.h
index fc15910..8576004 100644
--- a/board/ti/common/board_detect.h
+++ b/board/ti/common/board_detect.h
@@ -98,7 +98,7 @@ struct ti_common_eeprom {
 };
 
 #define TI_EEPROM_DATA ((struct ti_common_eeprom *)\
-				OMAP_SRAM_SCRATCH_BOARD_EEPROM_START)
+				TI_SRAM_SCRATCH_BOARD_EEPROM_START)
 
 /**
  * ti_i2c_eeprom_am_get() - Consolidated eeprom data collection for AM* TI EVMs
-- 
2.7.4

[U-Boot] [PATCH 5/7] board: ti: am57xx-idk: Auto detect LCD Panel

[menon.nishanth at gmail.com]

[...]


> diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h
> index 6de19c2..1fa2f82 100644
> --- a/include/configs/ti_omap5_common.h
> +++ b/include/configs/ti_omap5_common.h
> @@ -91,16 +91,22 @@
>                         "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
>                 "if test $board_name = beagle_x15_revb1; then " \
>                         "setenv fdtfile am57xx-beagle-x15-revb1.dtb; fi;" \
> -               "if test $board_name = am572x_idk; then " \
> -                       "setenv fdtfile am572x-idk.dtb; fi;" \
>                 "if test $board_name = am57xx_evm; then " \
>                         "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
>                 "if test $board_name = am57xx_evm_reva3; then " \
>                         "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
> +               "if test $board_name = am572x_idk && test $idk_lcd = no; then " \
> +                       "setenv fdtfile am572x-idk.dtb; fi;" \
> +               "if test $board_name = am572x_idk && test $idk_lcd = osd101t2045; then " \
> +                       "setenv fdtfile am572x-idk-lcd-osd.dtb; fi;" \
> +               "if test $board_name = am572x_idk && test $idk_lcd = osd101t2587; then " \
> +                       "setenv fdtfile am572x-idk-lcd-osd101t2587.dtb; fi;" \
>                 "if test $board_name = am571x_idk && test $idk_lcd = no; then " \
>                         "setenv fdtfile am571x-idk.dtb; fi;" \
>                 "if test $board_name = am571x_idk && test $idk_lcd = osd101t2045; then " \
>                         "setenv fdtfile am571x-idk-lcd-osd.dtb; fi;" \
> +               "if test $board_name = am571x_idk && test $idk_lcd = osd101t2587; then " \
> +                       "setenv fdtfile am571x-idk-lcd-osd101t2587.dtb; fi;" \


please drop the fdt selection from your patches. upstream will be
using dt overlay for these variations. rest of the detection code is
ok to go.

---
Regards,
Nishanth Menon

[U-Boot] [PATCH 1/7] ARM: OMAP5+: GPIO: Add GPIO_TO_PIN() macro

[Tom Rini]

On Thu, Jan 26, 2017 at 03:07:23PM +0200, Roger Quadros wrote:

> GPIO_TO_PIN(bank, bank_gpio) returns the GPIO index
> from the GPIO bank number and bank's GPIO offset number.
> 
> Signed-off-by: Roger Quadros <rogerq@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170126/54a7ee16/attachment.sig>

[U-Boot] [PATCH 2/7] ti: common: board_detect: commodify ethaddr environment setting code

[Tom Rini]

On Thu, Jan 26, 2017 at 03:07:24PM +0200, Roger Quadros wrote:

> As Keystone platforms also need this let's move this function
> to the common board_detect code.

This exists elsewhere?  If so, it should be removed in this patch too.
Also:

> +void __maybe_unused board_ti_set_ethaddr(int index)

We shouldn't need __maybe_unused here as it's a public function and will
get discarded already if unused.

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170126/06b477b3/attachment.sig>

[U-Boot] [PATCH 3/7] board: ti: am571x-idk: Support 6 port Ethernet or 4 port Ethernet with LCD

[Tom Rini]

On Thu, Jan 26, 2017 at 03:07:25PM +0200, Roger Quadros wrote:

> The board can support either ICSS1 Ethernet ports or LCD
> based on J51 jumper. Factory default is ICSS1 Ethernet ports
> (i.e. Jumper not populated).
> 
> Use the GPIO to detect the jumper setting and configure the
> pinmux accordingly. Also select the right DT blob based on
> the chosen configuration.
> 
> J51 absent -> ICSS1 Ethernet, no LCD on VOUT -> am571x-idk.dtb
> J51 present -> LCD on VOUT, no ICSS1 Ethernet -> am571x-idk-lcd-osd.dtb
> 
> At present we only support the assume it is the Legacy LCD.
> LCD detection mechanism needs to be added later to differentiate
> between legacy vs new LCD.
> 
> For ICSS1 Ethernet pins use the following convention to set the pinmux
> as PMT data is not yet finalized.
> 
> - If pin is output, set as PIN_OUTPUT
> - If pin is input and external pull resistor present set as PIN_INPUT
> - If pin is input and external pull resistor absent, set pull to same
> as that of the external PHY's internall pull.
> - Do not use SLEW_CONTROLon any pin.
> 
> [nm at ti.com] Fix wrong dtb selection caused by a typo ';'
> 
> Cc: Nishanth Menon <nm@ti.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170126/789774dc/attachment.sig>

[U-Boot] [PATCH 4/7] board: ti: am571x-idk: Update pinmux for ICSS2 Ethernet

[Tom Rini]

On Thu, Jan 26, 2017 at 03:07:26PM +0200, Roger Quadros wrote:

> Use the same convention that was used for ICSS1 Ethernet
> - If pin is output, set as PIN_OUTPUT
> - If pin is input and external pull resistor present set as PIN_INPUT
> - If pin is input and external pull resistor absent, set pull to same
> as that of the external PHY's internall pull.
> 
> Signed-off-by: Roger Quadros <rogerq@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170126/ee33c589/attachment.sig>

[U-Boot] [PATCH 5/7] board: ti: am57xx-idk: Auto detect LCD Panel

[Tom Rini]

On Thu, Jan 26, 2017 at 03:07:27PM +0200, Roger Quadros wrote:

> From: Nishanth Menon <nm@ti.com>
> 
> AM571x IDK and AM572x IDK have optional LCD Kits that can be purchased.
> These can be one of OSD101T2045 or the newer OSD101T2587. The LCD panel
> itself has no registers that can be used to identify the panel, however,
> the touchscreen controllers on the panels are different.
> 
> Hence to ease user experience, we can use the touch screen controller's
> ID information to detect what kind of panel we use and select the
> appropriate kernel dtb for the platform configuration.
> 
> NOTE: AM572x IDK default configuration is for LCD Connectivity, however
> the AM571x IDK has a jumper (J51) that needs to be mounted for the IDK
> to operate with LCD (Vs two PRUSS ethernet port option).
> 
> Touchscreen ID information is documented in:
> http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf
> 
> Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> Signed-off-by: Roger Quadros <rogerq@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170126/9dfe9cef/attachment.sig>

[U-Boot] [PATCH 6/7] ARM: k2g: setup PRU ethernet MAC addresses

[Tom Rini]

On Thu, Jan 26, 2017 at 03:07:28PM +0200, Roger Quadros wrote:

> PRU ethernet MAC address range is present in the
> board EEPROM. Parse it and setup eth?addr
> environment variables.
[snip]
> +#ifdef CONFIG_BOARD_LATE_INIT
> +int board_late_init(void)
> +{
> +	__maybe_unused int rc;
> +
> +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_TI_I2C_BOARD_DETECT)

Just move the #if up to include 'int rc' and we don't need to declare it
__maybe_unused then.

[snip]
> +/* Board Detection EEPROM */
> +#define CONFIG_EEPROM_BUS_ADDRESS	0
> +#define CONFIG_EEPROM_CHIP_ADDRESS	0x50

Only dra7xx and am57xx use these CONFIG options currently, please
migrate them to Kconfig instead of adding another board, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170126/5f0a1404/attachment.sig>

[U-Boot] [PATCH 2/7] ti: common: board_detect: commodify ethaddr environment setting code

[Roger Quadros]

Tom,

On 26/01/17 19:41, Tom Rini wrote:
> On Thu, Jan 26, 2017 at 03:07:24PM +0200, Roger Quadros wrote:
> 
>> As Keystone platforms also need this let's move this function
>> to the common board_detect code.
> 
> This exists elsewhere?  If so, it should be removed in this patch too.

I'll rewrite the commit log. It doesn't exist anywhere so we're not
moving anything here.

> Also:
> 
>> +void __maybe_unused board_ti_set_ethaddr(int index)
> 
> We shouldn't need __maybe_unused here as it's a public function and will
> get discarded already if unused.
> 

OK.

cheers,
-roger

[U-Boot] [PATCH 5/7] board: ti: am57xx-idk: Auto detect LCD Panel

[Roger Quadros]

On 26/01/17 19:33, menon.nishanth at gmail.com wrote:
> [...]
> 
> 
>> diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h
>> index 6de19c2..1fa2f82 100644
>> --- a/include/configs/ti_omap5_common.h
>> +++ b/include/configs/ti_omap5_common.h
>> @@ -91,16 +91,22 @@
>>                         "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
>>                 "if test $board_name = beagle_x15_revb1; then " \
>>                         "setenv fdtfile am57xx-beagle-x15-revb1.dtb; fi;" \
>> -               "if test $board_name = am572x_idk; then " \
>> -                       "setenv fdtfile am572x-idk.dtb; fi;" \
>>                 "if test $board_name = am57xx_evm; then " \
>>                         "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
>>                 "if test $board_name = am57xx_evm_reva3; then " \
>>                         "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
>> +               "if test $board_name = am572x_idk && test $idk_lcd = no; then " \
>> +                       "setenv fdtfile am572x-idk.dtb; fi;" \
>> +               "if test $board_name = am572x_idk && test $idk_lcd = osd101t2045; then " \
>> +                       "setenv fdtfile am572x-idk-lcd-osd.dtb; fi;" \
>> +               "if test $board_name = am572x_idk && test $idk_lcd = osd101t2587; then " \
>> +                       "setenv fdtfile am572x-idk-lcd-osd101t2587.dtb; fi;" \
>>                 "if test $board_name = am571x_idk && test $idk_lcd = no; then " \
>>                         "setenv fdtfile am571x-idk.dtb; fi;" \
>>                 "if test $board_name = am571x_idk && test $idk_lcd = osd101t2045; then " \
>>                         "setenv fdtfile am571x-idk-lcd-osd.dtb; fi;" \
>> +               "if test $board_name = am571x_idk && test $idk_lcd = osd101t2587; then " \
>> +                       "setenv fdtfile am571x-idk-lcd-osd101t2587.dtb; fi;" \
> 
> 
> please drop the fdt selection from your patches. upstream will be
> using dt overlay for these variations. rest of the detection code is
> ok to go.
> 

OK.
Just to clarify, dt overlay code will use the idk_lcd variable to patch the DT right?

cheeers,
-roger

[U-Boot] [PATCH 6/7] ARM: k2g: setup PRU ethernet MAC addresses

[Roger Quadros]

On 26/01/17 19:41, Tom Rini wrote:
> On Thu, Jan 26, 2017 at 03:07:28PM +0200, Roger Quadros wrote:
> 
>> PRU ethernet MAC address range is present in the
>> board EEPROM. Parse it and setup eth?addr
>> environment variables.
> [snip]
>> +#ifdef CONFIG_BOARD_LATE_INIT
>> +int board_late_init(void)
>> +{
>> +	__maybe_unused int rc;
>> +
>> +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_TI_I2C_BOARD_DETECT)
> 
> Just move the #if up to include 'int rc' and we don't need to declare it
> __maybe_unused then.

OK.
> 
> [snip]
>> +/* Board Detection EEPROM */
>> +#define CONFIG_EEPROM_BUS_ADDRESS	0
>> +#define CONFIG_EEPROM_CHIP_ADDRESS	0x50
> 
> Only dra7xx and am57xx use these CONFIG options currently, please
> migrate them to Kconfig instead of adding another board, thanks!
> 

I didn't get this part. In this patch board_k2g.c is using those macros.
Are you suggesting to move this to Kconfig instead of putting them
in the board headers?

cheers,
-roger

[U-Boot] [PATCH 5/7] board: ti: am57xx-idk: Auto detect LCD Panel

[menon.nishanth at gmail.com]

On Fri, Jan 27, 2017 at 2:54 AM, Roger Quadros <rogerq@ti.com> wrote:
> On 26/01/17 19:33, menon.nishanth at gmail.com wrote:
>> [...]
>>
>>
>>> diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h
>>> index 6de19c2..1fa2f82 100644
>>> --- a/include/configs/ti_omap5_common.h
>>> +++ b/include/configs/ti_omap5_common.h
>>> @@ -91,16 +91,22 @@
>>>                         "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
>>>                 "if test $board_name = beagle_x15_revb1; then " \
>>>                         "setenv fdtfile am57xx-beagle-x15-revb1.dtb; fi;" \
>>> -               "if test $board_name = am572x_idk; then " \
>>> -                       "setenv fdtfile am572x-idk.dtb; fi;" \
>>>                 "if test $board_name = am57xx_evm; then " \
>>>                         "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
>>>                 "if test $board_name = am57xx_evm_reva3; then " \
>>>                         "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
>>> +               "if test $board_name = am572x_idk && test $idk_lcd = no; then " \
>>> +                       "setenv fdtfile am572x-idk.dtb; fi;" \
>>> +               "if test $board_name = am572x_idk && test $idk_lcd = osd101t2045; then " \
>>> +                       "setenv fdtfile am572x-idk-lcd-osd.dtb; fi;" \
>>> +               "if test $board_name = am572x_idk && test $idk_lcd = osd101t2587; then " \
>>> +                       "setenv fdtfile am572x-idk-lcd-osd101t2587.dtb; fi;" \
>>>                 "if test $board_name = am571x_idk && test $idk_lcd = no; then " \
>>>                         "setenv fdtfile am571x-idk.dtb; fi;" \
>>>                 "if test $board_name = am571x_idk && test $idk_lcd = osd101t2045; then " \
>>>                         "setenv fdtfile am571x-idk-lcd-osd.dtb; fi;" \
>>> +               "if test $board_name = am571x_idk && test $idk_lcd = osd101t2587; then " \
>>> +                       "setenv fdtfile am571x-idk-lcd-osd101t2587.dtb; fi;" \
>>
>>
>> please drop the fdt selection from your patches. upstream will be
>> using dt overlay for these variations. rest of the detection code is
>> ok to go.
>>
>
> OK.
> Just to clarify, dt overlay code will use the idk_lcd variable to patch the DT right?

That'd make sense.

Regards,
Nishanth Menon

[U-Boot] [PATCH 6/7] ARM: k2g: setup PRU ethernet MAC addresses

[Tom Rini]

On Fri, Jan 27, 2017 at 10:58:41AM +0200, Roger Quadros wrote:
> 
> On 26/01/17 19:41, Tom Rini wrote:
> > On Thu, Jan 26, 2017 at 03:07:28PM +0200, Roger Quadros wrote:
> > 
> >> PRU ethernet MAC address range is present in the
> >> board EEPROM. Parse it and setup eth?addr
> >> environment variables.
> > [snip]
> >> +#ifdef CONFIG_BOARD_LATE_INIT
> >> +int board_late_init(void)
> >> +{
> >> +	__maybe_unused int rc;
> >> +
> >> +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_TI_I2C_BOARD_DETECT)
> > 
> > Just move the #if up to include 'int rc' and we don't need to declare it
> > __maybe_unused then.
> 
> OK.
> > 
> > [snip]
> >> +/* Board Detection EEPROM */
> >> +#define CONFIG_EEPROM_BUS_ADDRESS	0
> >> +#define CONFIG_EEPROM_CHIP_ADDRESS	0x50
> > 
> > Only dra7xx and am57xx use these CONFIG options currently, please
> > migrate them to Kconfig instead of adding another board, thanks!
> > 
> 
> I didn't get this part. In this patch board_k2g.c is using those macros.
> Are you suggesting to move this to Kconfig instead of putting them
> in the board headers?

Correct, move them to Kconfig (and migrate the other two boards).
Thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170127/28d7e377/attachment.sig>