* [U-Boot] [PATCH v2 01/15] imx6: Add imx6_src_get_boot_mode
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 02/15] imx: spl: Update NAND bootmode detection bit Jagan Teki
` (13 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
For i.MX6, the bootmode determine code is part of spl_boot_device,
but there is might be a possibility for other part the code need to
check the desired boot mode for adding new functionalities like
modeboot env variable, or changing boot order etc.
So introduced imx6_src_get_boot_mode which actually reading the
boot mode register for desired modes.
More cleanup will be add in future patches.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
---
arch/arm/imx-common/init.c | 12 ++++++++++++
arch/arm/imx-common/spl.c | 6 +++---
arch/arm/include/asm/imx-common/sys_proto.h | 14 ++++++++++++++
3 files changed, 29 insertions(+), 3 deletions(-)
diff --git a/arch/arm/imx-common/init.c b/arch/arm/imx-common/init.c
index e5dbd93..036ebb2 100644
--- a/arch/arm/imx-common/init.c
+++ b/arch/arm/imx-common/init.c
@@ -115,3 +115,15 @@ void boot_mode_apply(unsigned cfg_val)
writel(reg, &psrc->gpr10);
}
#endif
+
+#if defined(CONFIG_MX6)
+u32 imx6_src_get_boot_mode(void)
+{
+ struct src *psrc = (struct src *)SRC_BASE_ADDR;
+
+ if (imx6_is_bmode_from_gpr9())
+ return readl(&psrc->gpr9);
+ else
+ return readl(&psrc->sbmr1);
+}
+#endif
diff --git a/arch/arm/imx-common/spl.c b/arch/arm/imx-common/spl.c
index 60c4adf..a7f9705 100644
--- a/arch/arm/imx-common/spl.c
+++ b/arch/arm/imx-common/spl.c
@@ -10,6 +10,7 @@
#include <common.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
#include <asm/spl.h>
#include <spl.h>
#include <asm/imx-common/hab.h>
@@ -19,16 +20,15 @@
u32 spl_boot_device(void)
{
struct src *psrc = (struct src *)SRC_BASE_ADDR;
- unsigned int gpr10_boot = readl(&psrc->gpr10) & (1 << 28);
- unsigned reg = gpr10_boot ? readl(&psrc->gpr9) : readl(&psrc->sbmr1);
unsigned int bmode = readl(&psrc->sbmr2);
+ u32 reg = imx6_src_get_boot_mode();
/*
* Check for BMODE if serial downloader is enabled
* BOOT_MODE - see IMX6DQRM Table 8-1
*/
if ((((bmode >> 24) & 0x03) == 0x01) || /* Serial Downloader */
- (gpr10_boot && (reg == 1)))
+ (imx6_is_bmode_from_gpr9() && (reg == 1)))
return BOOT_DEVICE_UART;
/* BOOT_CFG1[7:4] - see IMX6DQRM Table 8-8 */
switch ((reg & 0x000000FF) >> 4) {
diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h
index 539d34b..99e3869 100644
--- a/arch/arm/include/asm/imx-common/sys_proto.h
+++ b/arch/arm/include/asm/imx-common/sys_proto.h
@@ -8,6 +8,7 @@
#ifndef _SYS_PROTO_H_
#define _SYS_PROTO_H_
+#include <asm/io.h>
#include <asm/imx-common/regs-common.h>
#include <common.h>
#include "../arch-imx/cpu.h"
@@ -38,6 +39,19 @@
#define is_mx6ull() (is_cpu_type(MXC_CPU_MX6ULL))
#define is_mx6sll() (is_cpu_type(MXC_CPU_MX6SLL))
+#ifdef CONFIG_MX6
+#define IMX6_SRC_GPR10_BMODE BIT(28)
+
+static inline u8 imx6_is_bmode_from_gpr9(void)
+{
+ struct src *psrc = (struct src *)SRC_BASE_ADDR;
+
+ return readl(&psrc->gpr10) & IMX6_SRC_GPR10_BMODE;
+}
+
+u32 imx6_src_get_boot_mode(void);
+#endif /* CONFIG_MX6 */
+
u32 get_nr_cpus(void);
u32 get_cpu_rev(void);
u32 get_cpu_speed_grade_hz(void);
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 02/15] imx: spl: Update NAND bootmode detection bit
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 01/15] imx6: Add imx6_src_get_boot_mode Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 03/15] imx: Use IMX6_BMODE_* macros instead of numericals Jagan Teki
` (12 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
BOOT_CFG1[7:4] the NAND boot mode selection is done
only when BOOT_CFG1[7] is 1 hence update the NAND
boot mode detection bit case. This information available
on Table 8-11. NAND Boot eFUSE Descriptions, from IMX6DQRM.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
---
arch/arm/imx-common/spl.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/imx-common/spl.c b/arch/arm/imx-common/spl.c
index a7f9705..fc3704b 100644
--- a/arch/arm/imx-common/spl.c
+++ b/arch/arm/imx-common/spl.c
@@ -61,8 +61,8 @@ u32 spl_boot_device(void)
case 0x6:
case 0x7:
return BOOT_DEVICE_MMC1;
- /* NAND Flash: 8.5.2 */
- case 0x8 ... 0xf:
+ /* NAND Flash: 8.5.2, Table 8-10 */
+ case 0x8:
return BOOT_DEVICE_NAND;
}
return BOOT_DEVICE_NONE;
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 03/15] imx: Use IMX6_BMODE_* macros instead of numericals
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 01/15] imx6: Add imx6_src_get_boot_mode Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 02/15] imx: spl: Update NAND bootmode detection bit Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 15:18 ` Eric Nelson
2017-01-27 14:12 ` [U-Boot] [PATCH v2 04/15] imx6: Add src_base structure define macro Jagan Teki
` (11 subsequent siblings)
14 siblings, 1 reply; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
Use meaningful meacros IMX6_BMODE_*, instead of numerical
number in boot mode detection code.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
---
arch/arm/imx-common/spl.c | 39 ++++++++++++++++++-----------
arch/arm/include/asm/imx-common/sys_proto.h | 34 +++++++++++++++++++++++++
2 files changed, 58 insertions(+), 15 deletions(-)
diff --git a/arch/arm/imx-common/spl.c b/arch/arm/imx-common/spl.c
index fc3704b..38789b2 100644
--- a/arch/arm/imx-common/spl.c
+++ b/arch/arm/imx-common/spl.c
@@ -30,39 +30,48 @@ u32 spl_boot_device(void)
if ((((bmode >> 24) & 0x03) == 0x01) || /* Serial Downloader */
(imx6_is_bmode_from_gpr9() && (reg == 1)))
return BOOT_DEVICE_UART;
+
/* BOOT_CFG1[7:4] - see IMX6DQRM Table 8-8 */
- switch ((reg & 0x000000FF) >> 4) {
+ switch ((reg & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
/* EIM: See 8.5.1, Table 8-9 */
- case 0x0:
+ case IMX6_BMODE_EMI:
/* BOOT_CFG1[3]: NOR/OneNAND Selection */
- if ((reg & 0x00000008) >> 3)
+ switch ((reg & IMX6_BMODE_EMI_MASK) >> IMX6_BMODE_EMI_SHIFT) {
+ case IMX6_BMODE_ONENAND:
return BOOT_DEVICE_ONENAND;
- else
+ case IMX6_BMODE_NOR:
return BOOT_DEVICE_NOR;
- break;
+ }
/* SATA: See 8.5.4, Table 8-20 */
- case 0x2:
+ case IMX6_BMODE_SATA:
return BOOT_DEVICE_SATA;
/* Serial ROM: See 8.5.5.1, Table 8-22 */
- case 0x3:
+ case IMX6_BMODE_SERIAL:
/* BOOT_CFG4[2:0] */
- switch ((reg & 0x07000000) >> 24) {
- case 0x0 ... 0x4:
+ switch ((reg & IMX6_BMODE_SERIAL_MASK) >>
+ IMX6_BMODE_SERIAL_SHIFT) {
+ case IMX6_BMODE_ECSPI1:
+ case IMX6_BMODE_ECSPI2:
+ case IMX6_BMODE_ECSPI3:
+ case IMX6_BMODE_ECSPI4:
+ case IMX6_BMODE_ECSPI5:
return BOOT_DEVICE_SPI;
- case 0x5 ... 0x7:
+ case IMX6_BMODE_I2C1:
+ case IMX6_BMODE_I2C2:
+ case IMX6_BMODE_I2C3:
return BOOT_DEVICE_I2C;
}
break;
/* SD/eSD: 8.5.3, Table 8-15 */
- case 0x4:
- case 0x5:
+ case IMX6_BMODE_SD:
+ case IMX6_BMODE_ESD:
return BOOT_DEVICE_MMC1;
/* MMC/eMMC: 8.5.3 */
- case 0x6:
- case 0x7:
+ case IMX6_BMODE_MMC:
+ case IMX6_BMODE_EMMC:
return BOOT_DEVICE_MMC1;
/* NAND Flash: 8.5.2, Table 8-10 */
- case 0x8:
+ case IMX6_BMODE_NAND:
return BOOT_DEVICE_NAND;
}
return BOOT_DEVICE_NONE;
diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h
index 99e3869..d0cf3f1 100644
--- a/arch/arm/include/asm/imx-common/sys_proto.h
+++ b/arch/arm/include/asm/imx-common/sys_proto.h
@@ -42,6 +42,40 @@
#ifdef CONFIG_MX6
#define IMX6_SRC_GPR10_BMODE BIT(28)
+#define IMX6_BMODE_MASK GENMASK(7, 0)
+#define IMX6_BMODE_SHIFT BIT(2)
+#define IMX6_BMODE_EMI_MASK BIT(3)
+#define IMX6_BMODE_EMI_SHIFT GENMASK(1, 0)
+#define IMX6_BMODE_SERIAL_MASK GENMASK(26, 24)
+#define IMX6_BMODE_SERIAL_SHIFT GENMASK(4, 3)
+
+enum imx6_bmode_serial {
+ IMX6_BMODE_ECSPI1,
+ IMX6_BMODE_ECSPI2,
+ IMX6_BMODE_ECSPI3,
+ IMX6_BMODE_ECSPI4,
+ IMX6_BMODE_ECSPI5,
+ IMX6_BMODE_I2C1,
+ IMX6_BMODE_I2C2,
+ IMX6_BMODE_I2C3,
+};
+
+enum imx6_bmode_emi {
+ IMX6_BMODE_ONENAND,
+ IMX6_BMODE_NOR,
+};
+
+enum imx6_bmode {
+ IMX6_BMODE_EMI,
+ IMX6_BMODE_SATA = 0x2,
+ IMX6_BMODE_SERIAL,
+ IMX6_BMODE_SD,
+ IMX6_BMODE_ESD,
+ IMX6_BMODE_MMC,
+ IMX6_BMODE_EMMC,
+ IMX6_BMODE_NAND,
+};
+
static inline u8 imx6_is_bmode_from_gpr9(void)
{
struct src *psrc = (struct src *)SRC_BASE_ADDR;
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 03/15] imx: Use IMX6_BMODE_* macros instead of numericals
2017-01-27 14:12 ` [U-Boot] [PATCH v2 03/15] imx: Use IMX6_BMODE_* macros instead of numericals Jagan Teki
@ 2017-01-27 15:18 ` Eric Nelson
2017-01-27 17:21 ` Jagan Teki
0 siblings, 1 reply; 22+ messages in thread
From: Eric Nelson @ 2017-01-27 15:18 UTC (permalink / raw)
To: u-boot
Hi Jagan,
Love this patch! This was long overdue.
On 01/27/2017 07:12 AM, Jagan Teki wrote:
> Use meaningful meacros IMX6_BMODE_*, instead of numerical
> number in boot mode detection code.
s/meacros/macros/
>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Tim Harvey <tharvey@gateworks.com>
> Signed-off-by: Jagan Teki <jagan@openedev.com>
> ---
> arch/arm/imx-common/spl.c | 39 ++++++++++++++++++-----------
> arch/arm/include/asm/imx-common/sys_proto.h | 34 +++++++++++++++++++++++++
> 2 files changed, 58 insertions(+), 15 deletions(-)
>
> diff --git a/arch/arm/imx-common/spl.c b/arch/arm/imx-common/spl.c
> index fc3704b..38789b2 100644
> --- a/arch/arm/imx-common/spl.c
> +++ b/arch/arm/imx-common/spl.c
> @@ -30,39 +30,48 @@ u32 spl_boot_device(void)
> if ((((bmode >> 24) & 0x03) == 0x01) || /* Serial Downloader */
> (imx6_is_bmode_from_gpr9() && (reg == 1)))
> return BOOT_DEVICE_UART;
> +
> /* BOOT_CFG1[7:4] - see IMX6DQRM Table 8-8 */
> - switch ((reg & 0x000000FF) >> 4) {
> + switch ((reg & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
> /* EIM: See 8.5.1, Table 8-9 */
> - case 0x0:
> + case IMX6_BMODE_EMI:
> /* BOOT_CFG1[3]: NOR/OneNAND Selection */
> - if ((reg & 0x00000008) >> 3)
> + switch ((reg & IMX6_BMODE_EMI_MASK) >> IMX6_BMODE_EMI_SHIFT) {
> + case IMX6_BMODE_ONENAND:
> return BOOT_DEVICE_ONENAND;
> - else
> + case IMX6_BMODE_NOR:
> return BOOT_DEVICE_NOR;
> - break;
> + }
> /* SATA: See 8.5.4, Table 8-20 */
> - case 0x2:
> + case IMX6_BMODE_SATA:
> return BOOT_DEVICE_SATA;
> /* Serial ROM: See 8.5.5.1, Table 8-22 */
> - case 0x3:
> + case IMX6_BMODE_SERIAL:
> /* BOOT_CFG4[2:0] */
> - switch ((reg & 0x07000000) >> 24) {
> - case 0x0 ... 0x4:
> + switch ((reg & IMX6_BMODE_SERIAL_MASK) >>
> + IMX6_BMODE_SERIAL_SHIFT) {
> + case IMX6_BMODE_ECSPI1:
> + case IMX6_BMODE_ECSPI2:
> + case IMX6_BMODE_ECSPI3:
> + case IMX6_BMODE_ECSPI4:
> + case IMX6_BMODE_ECSPI5:
> return BOOT_DEVICE_SPI;
> - case 0x5 ... 0x7:
> + case IMX6_BMODE_I2C1:
> + case IMX6_BMODE_I2C2:
> + case IMX6_BMODE_I2C3:
> return BOOT_DEVICE_I2C;
> }
> break;
> /* SD/eSD: 8.5.3, Table 8-15 */
> - case 0x4:
> - case 0x5:
> + case IMX6_BMODE_SD:
> + case IMX6_BMODE_ESD:
> return BOOT_DEVICE_MMC1;
> /* MMC/eMMC: 8.5.3 */
> - case 0x6:
> - case 0x7:
> + case IMX6_BMODE_MMC:
> + case IMX6_BMODE_EMMC:
> return BOOT_DEVICE_MMC1;
> /* NAND Flash: 8.5.2, Table 8-10 */
> - case 0x8:
> + case IMX6_BMODE_NAND:
> return BOOT_DEVICE_NAND;
> }
> return BOOT_DEVICE_NONE;
> diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h
> index 99e3869..d0cf3f1 100644
> --- a/arch/arm/include/asm/imx-common/sys_proto.h
> +++ b/arch/arm/include/asm/imx-common/sys_proto.h
> @@ -42,6 +42,40 @@
> #ifdef CONFIG_MX6
> #define IMX6_SRC_GPR10_BMODE BIT(28)
>
> +#define IMX6_BMODE_MASK GENMASK(7, 0)
This is a number (4), not a mask:
> +#define IMX6_BMODE_SHIFT BIT(2)
> +#define IMX6_BMODE_EMI_MASK BIT(3)
Ditto (number, not mask):
> +#define IMX6_BMODE_EMI_SHIFT GENMASK(1, 0)
Since there's also a "serial download mode", I'd prefer that these
say "SERIAL_NOR" to avoid confusion.
> +#define IMX6_BMODE_SERIAL_MASK GENMASK(26, 24)
> +#define IMX6_BMODE_SERIAL_SHIFT GENMASK(4, 3)
> +
I'd prefer macros for these because they'd show the
values directly, making a comparison with the RM
easier.
> +enum imx6_bmode_serial {
> + IMX6_BMODE_ECSPI1,
> + IMX6_BMODE_ECSPI2,
> + IMX6_BMODE_ECSPI3,
> + IMX6_BMODE_ECSPI4,
> + IMX6_BMODE_ECSPI5,
> + IMX6_BMODE_I2C1,
> + IMX6_BMODE_I2C2,
> + IMX6_BMODE_I2C3,
> +};
> +
> +enum imx6_bmode_emi {
> + IMX6_BMODE_ONENAND,
> + IMX6_BMODE_NOR,
> +};
> +
> +enum imx6_bmode {
> + IMX6_BMODE_EMI,
Especially when doing things like this:
> + IMX6_BMODE_SATA = 0x2,
> + IMX6_BMODE_SERIAL,
> + IMX6_BMODE_SD,
> + IMX6_BMODE_ESD,
> + IMX6_BMODE_MMC,
> + IMX6_BMODE_EMMC,
> + IMX6_BMODE_NAND,
> +};
> +
> static inline u8 imx6_is_bmode_from_gpr9(void)
> {
> struct src *psrc = (struct src *)SRC_BASE_ADDR;
>
^ permalink raw reply [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 03/15] imx: Use IMX6_BMODE_* macros instead of numericals
2017-01-27 15:18 ` Eric Nelson
@ 2017-01-27 17:21 ` Jagan Teki
2017-01-27 17:29 ` Eric Nelson
0 siblings, 1 reply; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 17:21 UTC (permalink / raw)
To: u-boot
On Fri, Jan 27, 2017 at 4:18 PM, Eric Nelson <eric@nelint.com> wrote:
> Hi Jagan,
>
> Love this patch! This was long overdue.
>
> On 01/27/2017 07:12 AM, Jagan Teki wrote:
>> Use meaningful meacros IMX6_BMODE_*, instead of numerical
>> number in boot mode detection code.
>
> s/meacros/macros/
>
>>
>> Cc: Stefano Babic <sbabic@denx.de>
>> Cc: Tim Harvey <tharvey@gateworks.com>
>> Signed-off-by: Jagan Teki <jagan@openedev.com>
>> ---
>> arch/arm/imx-common/spl.c | 39 ++++++++++++++++++-----------
>> arch/arm/include/asm/imx-common/sys_proto.h | 34 +++++++++++++++++++++++++
>> 2 files changed, 58 insertions(+), 15 deletions(-)
>>
>> diff --git a/arch/arm/imx-common/spl.c b/arch/arm/imx-common/spl.c
>> index fc3704b..38789b2 100644
>> --- a/arch/arm/imx-common/spl.c
>> +++ b/arch/arm/imx-common/spl.c
>> @@ -30,39 +30,48 @@ u32 spl_boot_device(void)
>> if ((((bmode >> 24) & 0x03) == 0x01) || /* Serial Downloader */
>> (imx6_is_bmode_from_gpr9() && (reg == 1)))
>> return BOOT_DEVICE_UART;
>> +
>> /* BOOT_CFG1[7:4] - see IMX6DQRM Table 8-8 */
>> - switch ((reg & 0x000000FF) >> 4) {
>> + switch ((reg & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
>> /* EIM: See 8.5.1, Table 8-9 */
>> - case 0x0:
>> + case IMX6_BMODE_EMI:
>> /* BOOT_CFG1[3]: NOR/OneNAND Selection */
>> - if ((reg & 0x00000008) >> 3)
>> + switch ((reg & IMX6_BMODE_EMI_MASK) >> IMX6_BMODE_EMI_SHIFT) {
>> + case IMX6_BMODE_ONENAND:
>> return BOOT_DEVICE_ONENAND;
>> - else
>> + case IMX6_BMODE_NOR:
>> return BOOT_DEVICE_NOR;
>> - break;
>> + }
>> /* SATA: See 8.5.4, Table 8-20 */
>> - case 0x2:
>> + case IMX6_BMODE_SATA:
>> return BOOT_DEVICE_SATA;
>> /* Serial ROM: See 8.5.5.1, Table 8-22 */
>> - case 0x3:
>> + case IMX6_BMODE_SERIAL:
>> /* BOOT_CFG4[2:0] */
>> - switch ((reg & 0x07000000) >> 24) {
>> - case 0x0 ... 0x4:
>> + switch ((reg & IMX6_BMODE_SERIAL_MASK) >>
>> + IMX6_BMODE_SERIAL_SHIFT) {
>> + case IMX6_BMODE_ECSPI1:
>> + case IMX6_BMODE_ECSPI2:
>> + case IMX6_BMODE_ECSPI3:
>> + case IMX6_BMODE_ECSPI4:
>> + case IMX6_BMODE_ECSPI5:
>> return BOOT_DEVICE_SPI;
>> - case 0x5 ... 0x7:
>> + case IMX6_BMODE_I2C1:
>> + case IMX6_BMODE_I2C2:
>> + case IMX6_BMODE_I2C3:
>> return BOOT_DEVICE_I2C;
>> }
>> break;
>> /* SD/eSD: 8.5.3, Table 8-15 */
>> - case 0x4:
>> - case 0x5:
>> + case IMX6_BMODE_SD:
>> + case IMX6_BMODE_ESD:
>> return BOOT_DEVICE_MMC1;
>> /* MMC/eMMC: 8.5.3 */
>> - case 0x6:
>> - case 0x7:
>> + case IMX6_BMODE_MMC:
>> + case IMX6_BMODE_EMMC:
>> return BOOT_DEVICE_MMC1;
>> /* NAND Flash: 8.5.2, Table 8-10 */
>> - case 0x8:
>> + case IMX6_BMODE_NAND:
>> return BOOT_DEVICE_NAND;
>> }
>> return BOOT_DEVICE_NONE;
>> diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h
>> index 99e3869..d0cf3f1 100644
>> --- a/arch/arm/include/asm/imx-common/sys_proto.h
>> +++ b/arch/arm/include/asm/imx-common/sys_proto.h
>> @@ -42,6 +42,40 @@
>> #ifdef CONFIG_MX6
>> #define IMX6_SRC_GPR10_BMODE BIT(28)
>>
>> +#define IMX6_BMODE_MASK GENMASK(7, 0)
>
> This is a number (4), not a mask:
This is 0xff not 4
- switch ((reg & 0x000000FF) >> 4) {
+ switch ((reg & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
>> +#define IMX6_BMODE_SHIFT BIT(2)
>> +#define IMX6_BMODE_EMI_MASK BIT(3)
>
> Ditto (number, not mask):
The reason for calling this as mask as the reg value is and'ing to
mask value of 8 (which is last 0 and 1 bits)
- if ((reg & 0x00000008) >> 3)
+ switch ((reg & IMX6_BMODE_EMI_MASK) >> IMX6_BMODE_EMI_SHIFT) {
>> +#define IMX6_BMODE_EMI_SHIFT GENMASK(1, 0)
>
> Since there's also a "serial download mode", I'd prefer that these
> say "SERIAL_NOR" to avoid confusion.
Since serial here is also denoting I2C better to have SERIAL and we
can use 'serial download' as SERIAL_DOWNLOAD or something similar.
>
>> +#define IMX6_BMODE_SERIAL_MASK GENMASK(26, 24)
>> +#define IMX6_BMODE_SERIAL_SHIFT GENMASK(4, 3)
>> +
>
> I'd prefer macros for these because they'd show the
> values directly, making a comparison with the RM
> easier.
But these macro's making bit functioning smooth.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 03/15] imx: Use IMX6_BMODE_* macros instead of numericals
2017-01-27 17:21 ` Jagan Teki
@ 2017-01-27 17:29 ` Eric Nelson
2017-01-27 17:54 ` Jagan Teki
0 siblings, 1 reply; 22+ messages in thread
From: Eric Nelson @ 2017-01-27 17:29 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On 01/27/2017 10:21 AM, Jagan Teki wrote:
> On Fri, Jan 27, 2017 at 4:18 PM, Eric Nelson <eric@nelint.com> wrote:
>> Hi Jagan,
>>
>> Love this patch! This was long overdue.
>>
>> On 01/27/2017 07:12 AM, Jagan Teki wrote:
>>> Use meaningful meacros IMX6_BMODE_*, instead of numerical
>>> number in boot mode detection code.
>>
>> s/meacros/macros/
>>
<snip>
>>> diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h
>>> index 99e3869..d0cf3f1 100644
>>> --- a/arch/arm/include/asm/imx-common/sys_proto.h
>>> +++ b/arch/arm/include/asm/imx-common/sys_proto.h
>>> @@ -42,6 +42,40 @@
>>> #ifdef CONFIG_MX6
>>> #define IMX6_SRC_GPR10_BMODE BIT(28)
>>>
>>> +#define IMX6_BMODE_MASK GENMASK(7, 0)
>>
>> This is a number (4), not a mask:
>
> This is 0xff not 4
I was referring to IMX6_BMODE_SHIFT.
> - switch ((reg & 0x000000FF) >> 4) {
> + switch ((reg & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
>
>>> +#define IMX6_BMODE_SHIFT BIT(2)
>>> +#define IMX6_BMODE_EMI_MASK BIT(3)
>>
>> Ditto (number, not mask):
>
> The reason for calling this as mask as the reg value is and'ing to
> mask value of 8 (which is last 0 and 1 bits)
> - if ((reg & 0x00000008) >> 3)
> + switch ((reg & IMX6_BMODE_EMI_MASK) >> IMX6_BMODE_EMI_SHIFT) {
>
Again, I'm referring to the _SHIFT macro below:
>>> +#define IMX6_BMODE_EMI_SHIFT GENMASK(1, 0)
>>
>> Since there's also a "serial download mode", I'd prefer that these
>> say "SERIAL_NOR" to avoid confusion.
>
> Since serial here is also denoting I2C better to have SERIAL and we
> can use 'serial download' as SERIAL_DOWNLOAD or something similar.
>
I2C is also serial ROM or serial NOR.
BMODE_SERIAL just seems to have multiple meanings.
>>
>>> +#define IMX6_BMODE_SERIAL_MASK GENMASK(26, 24)
>>> +#define IMX6_BMODE_SERIAL_SHIFT GENMASK(4, 3)
>>> +
>>
>> I'd prefer macros for these because they'd show the
>> values directly, making a comparison with the RM
>> easier.
>
> But these macro's making bit functioning smooth.
>
My comment here was referring to the use of enums for
imx6_bmode, imx6_bmode_emi, and imx6_bmode_serial.
If you use macros, it's easier to see that, for instance
IMX6_BMODE_EMMC == 7
> thanks!
>
No. Thank you for the patch. This was pretty contorted previously.
Regards,
Eric
^ permalink raw reply [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 03/15] imx: Use IMX6_BMODE_* macros instead of numericals
2017-01-27 17:29 ` Eric Nelson
@ 2017-01-27 17:54 ` Jagan Teki
2017-01-27 18:10 ` Eric Nelson
0 siblings, 1 reply; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 17:54 UTC (permalink / raw)
To: u-boot
On Fri, Jan 27, 2017 at 6:29 PM, Eric Nelson <eric@nelint.com> wrote:
> Hi Jagan,
>
> On 01/27/2017 10:21 AM, Jagan Teki wrote:
>> On Fri, Jan 27, 2017 at 4:18 PM, Eric Nelson <eric@nelint.com> wrote:
>>> Hi Jagan,
>>>
>>> Love this patch! This was long overdue.
>>>
>>> On 01/27/2017 07:12 AM, Jagan Teki wrote:
>>>> Use meaningful meacros IMX6_BMODE_*, instead of numerical
>>>> number in boot mode detection code.
>>>
>>> s/meacros/macros/
>>>
>
> <snip>
>
>>>> diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h
>>>> index 99e3869..d0cf3f1 100644
>>>> --- a/arch/arm/include/asm/imx-common/sys_proto.h
>>>> +++ b/arch/arm/include/asm/imx-common/sys_proto.h
>>>> @@ -42,6 +42,40 @@
>>>> #ifdef CONFIG_MX6
>>>> #define IMX6_SRC_GPR10_BMODE BIT(28)
>>>>
>>>> +#define IMX6_BMODE_MASK GENMASK(7, 0)
>>>
>>> This is a number (4), not a mask:
>>
>> This is 0xff not 4
>
> I was referring to IMX6_BMODE_SHIFT.
Sorry, I thought you replied on in-line to my messages and I'm trying
to use bitops for possible vlaue BIT(2) make the value 4 (1 << 2)
>
>> - switch ((reg & 0x000000FF) >> 4) {
>> + switch ((reg & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
>>
>>>> +#define IMX6_BMODE_SHIFT BIT(2)
>>>> +#define IMX6_BMODE_EMI_MASK BIT(3)
>>>
>>> Ditto (number, not mask):
>>
>> The reason for calling this as mask as the reg value is and'ing to
>> mask value of 8 (which is last 0 and 1 bits)
>> - if ((reg & 0x00000008) >> 3)
>> + switch ((reg & IMX6_BMODE_EMI_MASK) >> IMX6_BMODE_EMI_SHIFT) {
>>
>
> Again, I'm referring to the _SHIFT macro below:
Same comment as above.
>
>>>> +#define IMX6_BMODE_EMI_SHIFT GENMASK(1, 0)
>>>
>>> Since there's also a "serial download mode", I'd prefer that these
>>> say "SERIAL_NOR" to avoid confusion.
>>
>> Since serial here is also denoting I2C better to have SERIAL and we
>> can use 'serial download' as SERIAL_DOWNLOAD or something similar.
>>
>
> I2C is also serial ROM or serial NOR.
>
> BMODE_SERIAL just seems to have multiple meanings.
SERIAL_ROM may be better because SERIAL_NOR look spi-nor flash.
>
>>>
>>>> +#define IMX6_BMODE_SERIAL_MASK GENMASK(26, 24)
>>>> +#define IMX6_BMODE_SERIAL_SHIFT GENMASK(4, 3)
>>>> +
>>>
>>> I'd prefer macros for these because they'd show the
>>> values directly, making a comparison with the RM
>>> easier.
>>
>> But these macro's making bit functioning smooth.
>>
>
> My comment here was referring to the use of enums for
> imx6_bmode, imx6_bmode_emi, and imx6_bmode_serial.
>
> If you use macros, it's easier to see that, for instance
> IMX6_BMODE_EMMC == 7
May be this is true with imx6_bmode but the rest have serial in
nature, but again enum make code compile time retain and good for for
code readable instead of assigning values unlike macro.s
>
>> thanks!
>>
>
> No. Thank you for the patch. This was pretty contorted previously.
:)
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 03/15] imx: Use IMX6_BMODE_* macros instead of numericals
2017-01-27 17:54 ` Jagan Teki
@ 2017-01-27 18:10 ` Eric Nelson
2017-01-27 18:26 ` Jagan Teki
0 siblings, 1 reply; 22+ messages in thread
From: Eric Nelson @ 2017-01-27 18:10 UTC (permalink / raw)
To: u-boot
Hi Jagan,
On 01/27/2017 10:54 AM, Jagan Teki wrote:
> On Fri, Jan 27, 2017 at 6:29 PM, Eric Nelson <eric@nelint.com> wrote:
>> Hi Jagan,
>>
>> On 01/27/2017 10:21 AM, Jagan Teki wrote:
>>> On Fri, Jan 27, 2017 at 4:18 PM, Eric Nelson <eric@nelint.com> wrote:
>>>> Hi Jagan,
>>>>
>>>> Love this patch! This was long overdue.
>>>>
>>>> On 01/27/2017 07:12 AM, Jagan Teki wrote:
>>>>> Use meaningful meacros IMX6_BMODE_*, instead of numerical
>>>>> number in boot mode detection code.
>>>>
>>>> s/meacros/macros/
>>>>
>>
>> <snip>
>>
>>>>> diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h
>>>>> index 99e3869..d0cf3f1 100644
>>>>> --- a/arch/arm/include/asm/imx-common/sys_proto.h
>>>>> +++ b/arch/arm/include/asm/imx-common/sys_proto.h
>>>>> @@ -42,6 +42,40 @@
>>>>> #ifdef CONFIG_MX6
>>>>> #define IMX6_SRC_GPR10_BMODE BIT(28)
>>>>>
>>>>> +#define IMX6_BMODE_MASK GENMASK(7, 0)
>>>>
>>>> This is a number (4), not a mask:
>>>
>>> This is 0xff not 4
>>
>> I was referring to IMX6_BMODE_SHIFT.
>
> Sorry, I thought you replied on in-line to my messages and I'm trying
> to use bitops for possible vlaue BIT(2) make the value 4 (1 << 2)
>
Methinks you tries too hard!
Bitops don't help when you're referring to a bit **position**, only
when referring to a mask.
>>
>>> - switch ((reg & 0x000000FF) >> 4) {
>>> + switch ((reg & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
>>>
>>>>> +#define IMX6_BMODE_SHIFT BIT(2)
>>>>> +#define IMX6_BMODE_EMI_MASK BIT(3)
>>>>
>>>> Ditto (number, not mask):
>>>
>>> The reason for calling this as mask as the reg value is and'ing to
>>> mask value of 8 (which is last 0 and 1 bits)
>>> - if ((reg & 0x00000008) >> 3)
>>> + switch ((reg & IMX6_BMODE_EMI_MASK) >> IMX6_BMODE_EMI_SHIFT) {
>>>
>>
>> Again, I'm referring to the _SHIFT macro below:
>
> Same comment as above.
>
>>
>>>>> +#define IMX6_BMODE_EMI_SHIFT GENMASK(1, 0)
>>>>
>>>> Since there's also a "serial download mode", I'd prefer that these
>>>> say "SERIAL_NOR" to avoid confusion.
>>>
>>> Since serial here is also denoting I2C better to have SERIAL and we
>>> can use 'serial download' as SERIAL_DOWNLOAD or something similar.
>>>
>>
>> I2C is also serial ROM or serial NOR.
>>
>> BMODE_SERIAL just seems to have multiple meanings.
>
> SERIAL_ROM may be better because SERIAL_NOR look spi-nor flash.
>
Okay by me.
>>
>>>>
>>>>> +#define IMX6_BMODE_SERIAL_MASK GENMASK(26, 24)
>>>>> +#define IMX6_BMODE_SERIAL_SHIFT GENMASK(4, 3)
>>>>> +
>>>>
>>>> I'd prefer macros for these because they'd show the
>>>> values directly, making a comparison with the RM
>>>> easier.
>>>
>>> But these macro's making bit functioning smooth.
>>>
>>
>> My comment here was referring to the use of enums for
>> imx6_bmode, imx6_bmode_emi, and imx6_bmode_serial.
>>
>> If you use macros, it's easier to see that, for instance
>> IMX6_BMODE_EMMC == 7
>
> May be this is true with imx6_bmode but the rest have serial in
> nature, but again enum make code compile time retain and good for for
> code readable instead of assigning values unlike macro.s
>
If these were likely to be used more widely, I might agree, but
opinions vary.
My main thought is that having the numbers handy would make
it easier to compare against the reference manual (which I haven't)
or even the constants you just replaced (which I also haven't done).
^ permalink raw reply [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 03/15] imx: Use IMX6_BMODE_* macros instead of numericals
2017-01-27 18:10 ` Eric Nelson
@ 2017-01-27 18:26 ` Jagan Teki
0 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 18:26 UTC (permalink / raw)
To: u-boot
On Fri, Jan 27, 2017 at 7:10 PM, Eric Nelson <eric@nelint.com> wrote:
> Hi Jagan,
>
> On 01/27/2017 10:54 AM, Jagan Teki wrote:
>> On Fri, Jan 27, 2017 at 6:29 PM, Eric Nelson <eric@nelint.com> wrote:
>>> Hi Jagan,
>>>
>>> On 01/27/2017 10:21 AM, Jagan Teki wrote:
>>>> On Fri, Jan 27, 2017 at 4:18 PM, Eric Nelson <eric@nelint.com> wrote:
>>>>> Hi Jagan,
>>>>>
>>>>> Love this patch! This was long overdue.
>>>>>
>>>>> On 01/27/2017 07:12 AM, Jagan Teki wrote:
>>>>>> Use meaningful meacros IMX6_BMODE_*, instead of numerical
>>>>>> number in boot mode detection code.
>>>>>
>>>>> s/meacros/macros/
>>>>>
>>>
>>> <snip>
>>>
>>>>>> diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h
>>>>>> index 99e3869..d0cf3f1 100644
>>>>>> --- a/arch/arm/include/asm/imx-common/sys_proto.h
>>>>>> +++ b/arch/arm/include/asm/imx-common/sys_proto.h
>>>>>> @@ -42,6 +42,40 @@
>>>>>> #ifdef CONFIG_MX6
>>>>>> #define IMX6_SRC_GPR10_BMODE BIT(28)
>>>>>>
>>>>>> +#define IMX6_BMODE_MASK GENMASK(7, 0)
>>>>>
>>>>> This is a number (4), not a mask:
>>>>
>>>> This is 0xff not 4
>>>
>>> I was referring to IMX6_BMODE_SHIFT.
>>
>> Sorry, I thought you replied on in-line to my messages and I'm trying
>> to use bitops for possible vlaue BIT(2) make the value 4 (1 << 2)
>>
>
> Methinks you tries too hard!
>
> Bitops don't help when you're referring to a bit **position**, only
> when referring to a mask.
OK, will fix.
>
>>>
>>>> - switch ((reg & 0x000000FF) >> 4) {
>>>> + switch ((reg & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
>>>>
>>>>>> +#define IMX6_BMODE_SHIFT BIT(2)
>>>>>> +#define IMX6_BMODE_EMI_MASK BIT(3)
>>>>>
>>>>> Ditto (number, not mask):
>>>>
>>>> The reason for calling this as mask as the reg value is and'ing to
>>>> mask value of 8 (which is last 0 and 1 bits)
>>>> - if ((reg & 0x00000008) >> 3)
>>>> + switch ((reg & IMX6_BMODE_EMI_MASK) >> IMX6_BMODE_EMI_SHIFT) {
>>>>
>>>
>>> Again, I'm referring to the _SHIFT macro below:
>>
>> Same comment as above.
>>
>>>
>>>>>> +#define IMX6_BMODE_EMI_SHIFT GENMASK(1, 0)
>>>>>
>>>>> Since there's also a "serial download mode", I'd prefer that these
>>>>> say "SERIAL_NOR" to avoid confusion.
>>>>
>>>> Since serial here is also denoting I2C better to have SERIAL and we
>>>> can use 'serial download' as SERIAL_DOWNLOAD or something similar.
>>>>
>>>
>>> I2C is also serial ROM or serial NOR.
>>>
>>> BMODE_SERIAL just seems to have multiple meanings.
>>
>> SERIAL_ROM may be better because SERIAL_NOR look spi-nor flash.
>>
>
> Okay by me.
>
>>>
>>>>>
>>>>>> +#define IMX6_BMODE_SERIAL_MASK GENMASK(26, 24)
>>>>>> +#define IMX6_BMODE_SERIAL_SHIFT GENMASK(4, 3)
>>>>>> +
>>>>>
>>>>> I'd prefer macros for these because they'd show the
>>>>> values directly, making a comparison with the RM
>>>>> easier.
>>>>
>>>> But these macro's making bit functioning smooth.
>>>>
>>>
>>> My comment here was referring to the use of enums for
>>> imx6_bmode, imx6_bmode_emi, and imx6_bmode_serial.
>>>
>>> If you use macros, it's easier to see that, for instance
>>> IMX6_BMODE_EMMC == 7
>>
>> May be this is true with imx6_bmode but the rest have serial in
>> nature, but again enum make code compile time retain and good for for
>> code readable instead of assigning values unlike macro.s
>>
>
> If these were likely to be used more widely, I might agree, but
> opinions vary.
>
> My main thought is that having the numbers handy would make
> it easier to compare against the reference manual (which I haven't)
> or even the constants you just replaced (which I also haven't done).
Ok, then I will assign the values directly for imx6_bmode.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 04/15] imx6: Add src_base structure define macro
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (2 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 03/15] imx: Use IMX6_BMODE_* macros instead of numericals Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 05/15] imx6: isiotmx6ul: Update SPL board boot order for eMMC Jagan Teki
` (10 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
Instead of initializing 'struct src' to SRC_BASE_ADDR on
every function better to have global define macro.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
---
arch/arm/imx-common/init.c | 6 ++----
arch/arm/imx-common/spl.c | 3 +--
arch/arm/include/asm/arch-mx6/imx-regs.h | 2 ++
arch/arm/include/asm/imx-common/sys_proto.h | 4 +---
4 files changed, 6 insertions(+), 9 deletions(-)
diff --git a/arch/arm/imx-common/init.c b/arch/arm/imx-common/init.c
index 036ebb2..5b4f828 100644
--- a/arch/arm/imx-common/init.c
+++ b/arch/arm/imx-common/init.c
@@ -119,11 +119,9 @@ void boot_mode_apply(unsigned cfg_val)
#if defined(CONFIG_MX6)
u32 imx6_src_get_boot_mode(void)
{
- struct src *psrc = (struct src *)SRC_BASE_ADDR;
-
if (imx6_is_bmode_from_gpr9())
- return readl(&psrc->gpr9);
+ return readl(&src_base->gpr9);
else
- return readl(&psrc->sbmr1);
+ return readl(&src_base->sbmr1);
}
#endif
diff --git a/arch/arm/imx-common/spl.c b/arch/arm/imx-common/spl.c
index 38789b2..4d73a67 100644
--- a/arch/arm/imx-common/spl.c
+++ b/arch/arm/imx-common/spl.c
@@ -19,8 +19,7 @@
/* determine boot device from SRC_SBMR1 (BOOT_CFG[4:1]) or SRC_GPR9 register */
u32 spl_boot_device(void)
{
- struct src *psrc = (struct src *)SRC_BASE_ADDR;
- unsigned int bmode = readl(&psrc->sbmr2);
+ unsigned int bmode = readl(&src_base->sbmr2);
u32 reg = imx6_src_get_boot_mode();
/*
diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h
index 6727c56..646013d 100644
--- a/arch/arm/include/asm/arch-mx6/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx6/imx-regs.h
@@ -473,6 +473,8 @@ struct src {
u32 gpr10;
};
+#define src_base ((struct src *)SRC_BASE_ADDR)
+
#define SRC_SCR_M4_ENABLE_OFFSET 22
#define SRC_SCR_M4_ENABLE_MASK (1 << 22)
#define SRC_SCR_M4C_NON_SCLR_RST_OFFSET 4
diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h
index d0cf3f1..d149c9f 100644
--- a/arch/arm/include/asm/imx-common/sys_proto.h
+++ b/arch/arm/include/asm/imx-common/sys_proto.h
@@ -78,9 +78,7 @@ enum imx6_bmode {
static inline u8 imx6_is_bmode_from_gpr9(void)
{
- struct src *psrc = (struct src *)SRC_BASE_ADDR;
-
- return readl(&psrc->gpr10) & IMX6_SRC_GPR10_BMODE;
+ return readl(&src_base->gpr10) & IMX6_SRC_GPR10_BMODE;
}
u32 imx6_src_get_boot_mode(void);
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 05/15] imx6: isiotmx6ul: Update SPL board boot order for eMMC
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (3 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 04/15] imx6: Add src_base structure define macro Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 06/15] i.MX6UL: isiot: Add eMMC boot support Jagan Teki
` (9 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
SPL mmc device index is get based on the boot device, like
- BOOT_DEVICE_MMC1 for mmc device 0
- BOOT_DEVICE_MMC2 for mmc device 1
Currently BOOT_DEVICE_MMC1 is setting both SD/eSD and MMC/eMMC
boot devices in i.MX, So u-boot is loading from mmc device 0 even
"if the board booting from SD/eSD or MMC/eMMC"
So, this patch set BOOT_DEVICE_MMC2 for MMC/eMMC so for MMC/eMMC
the u-boot is loading from mmc device 1 and the board file need to
take care if the board have different mmc device order intialization.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/isiotmx6ul/isiotmx6ul.c | 26 ++++++++++++++++++++++++++
1 file changed, 26 insertions(+)
diff --git a/board/engicam/isiotmx6ul/isiotmx6ul.c b/board/engicam/isiotmx6ul/isiotmx6ul.c
index ae3465f..6b84f02 100644
--- a/board/engicam/isiotmx6ul/isiotmx6ul.c
+++ b/board/engicam/isiotmx6ul/isiotmx6ul.c
@@ -205,6 +205,32 @@ int board_mmc_init(bd_t *bis)
return 0;
}
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+void board_boot_order(u32 *spl_boot_list)
+{
+ u32 bmode = imx6_src_get_boot_mode();
+ u8 boot_dev = BOOT_DEVICE_MMC1;
+
+ switch ((bmode & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
+ case IMX6_BMODE_SD:
+ case IMX6_BMODE_ESD:
+ /* SD/eSD - BOOT_DEVICE_MMC1 */
+ break;
+ case IMX6_BMODE_MMC:
+ case IMX6_BMODE_EMMC:
+ /* MMC/eMMC */
+ boot_dev = BOOT_DEVICE_MMC2;
+ break;
+ default:
+ /* Default - BOOT_DEVICE_MMC1 */
+ printf("Wrong board boot order\n");
+ break;
+ }
+
+ spl_boot_list[0] = boot_dev;
+}
+#endif
#endif /* CONFIG_FSL_ESDHC */
static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 06/15] i.MX6UL: isiot: Add eMMC boot support
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (4 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 05/15] imx6: isiotmx6ul: Update SPL board boot order for eMMC Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 07/15] i.MX6UL: isiot: Add modeboot env via board_late_init Jagan Teki
` (8 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Boot from eMMC:
--------------
U-Boot SPL 2017.01-00314-gd0cd9cd-dirty (Jan 25 2017 - 13:25:27)
Trying to boot from MMC2
U-Boot 2017.01-00314-gd0cd9cd-dirty (Jan 25 2017 - 13:25:27 +0100)
CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 36C
Reset cause: POR
Model: Engicam Is.IoT MX6UL eMMC Starterkit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
switch to partitions #0, OK
mmc1(part 0) is current device
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/imx6ul-isiot-emmc.dts | 77 +++++++++++++++++++++++++++++++++++
board/engicam/isiotmx6ul/MAINTAINERS | 1 +
board/engicam/isiotmx6ul/isiotmx6ul.c | 26 +++++++++++-
configs/imx6ul_isiot_emmc_defconfig | 39 ++++++++++++++++++
include/configs/imx6ul_isiot.h | 2 +-
6 files changed, 144 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/dts/imx6ul-isiot-emmc.dts
create mode 100644 configs/imx6ul_isiot_emmc_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 09e3bdb..cde7f41 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -314,6 +314,7 @@ dtb-$(CONFIG_MX6) += imx6ull-14x14-evk.dtb \
imx6q-icore.dtb \
imx6q-icore-rqs.dtb \
imx6ul-geam-kit.dtb \
+ imx6ul-isiot-emmc.dtb \
imx6ul-isiot-mmc.dtb \
imx6ul-isiot-nand.dtb
diff --git a/arch/arm/dts/imx6ul-isiot-emmc.dts b/arch/arm/dts/imx6ul-isiot-emmc.dts
new file mode 100644
index 0000000..677de96
--- /dev/null
+++ b/arch/arm/dts/imx6ul-isiot-emmc.dts
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2016 Amarula Solutions B.V.
+ * Copyright (C) 2016 Engicam S.r.l.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6ul-isiot.dtsi"
+
+/ {
+ model = "Engicam Is.IoT MX6UL eMMC Starterkit";
+ compatible = "engicam,imx6ul-isiot", "fsl,imx6ul";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+ bus-width = <8>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17070
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x10070
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17070
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17070
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17070
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17070
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17070
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17070
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17070
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17070
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x17070
+ >;
+ };
+};
diff --git a/board/engicam/isiotmx6ul/MAINTAINERS b/board/engicam/isiotmx6ul/MAINTAINERS
index e99e02e..c99dfaa 100644
--- a/board/engicam/isiotmx6ul/MAINTAINERS
+++ b/board/engicam/isiotmx6ul/MAINTAINERS
@@ -4,4 +4,5 @@ S: Maintained
F: board/engicam/isiotmx6ul
F: include/configs/imx6ul_isiot.h
F: configs/imx6ul_isiot_mmc_defconfig
+F: configs/imx6ul_isiot_emmc_defconfig
F: configs/imx6ul_isiot_nand_defconfig
diff --git a/board/engicam/isiotmx6ul/isiotmx6ul.c b/board/engicam/isiotmx6ul/isiotmx6ul.c
index 6b84f02..17c19e0 100644
--- a/board/engicam/isiotmx6ul/isiotmx6ul.c
+++ b/board/engicam/isiotmx6ul/isiotmx6ul.c
@@ -153,10 +153,24 @@ static iomux_v3_cfg_t const usdhc1_pads[] = {
MX6_PAD_GPIO1_IO09__GPIO1_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_NAND_ALE__USDHC2_RESET_B | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA00__USDHC2_DATA0| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA04__USDHC2_DATA4| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 19)
+#define USDHC2_CD_GPIO IMX_GPIO_NR(4, 5)
-struct fsl_esdhc_cfg usdhc_cfg[1] = {
+struct fsl_esdhc_cfg usdhc_cfg[2] = {
{USDHC1_BASE_ADDR, 0, 4},
+ {USDHC2_BASE_ADDR, 0, 8},
};
int board_mmc_getcd(struct mmc *mmc)
@@ -168,6 +182,9 @@ int board_mmc_getcd(struct mmc *mmc)
case USDHC1_BASE_ADDR:
ret = !gpio_get_value(USDHC1_CD_GPIO);
break;
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
}
return ret;
@@ -181,6 +198,7 @@ int board_mmc_init(bd_t *bis)
* According to the board_mmc_init() the following map is done:
* (U-boot device node) (Physical Port)
* mmc0 USDHC1
+ * mmc1 USDHC2
*/
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
switch (i) {
@@ -190,6 +208,12 @@ int board_mmc_init(bd_t *bis)
gpio_direction_input(USDHC1_CD_GPIO);
usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc1_pads, ARRAY_SIZE(usdhc2_pads));
+ gpio_direction_input(USDHC2_CD_GPIO);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ break;
default:
printf("Warning - USDHC%d controller not supporting\n",
i + 1);
diff --git a/configs/imx6ul_isiot_emmc_defconfig b/configs/imx6ul_isiot_emmc_defconfig
new file mode 100644
index 0000000..94fe808
--- /dev/null
+++ b/configs/imx6ul_isiot_emmc_defconfig
@@ -0,0 +1,39 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_TARGET_MX6UL_ISIOT=y
+CONFIG_SPL_EXT_SUPPORT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6ul-isiot-emmc"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,ENV_IS_IN_MMC"
+CONFIG_BOOTDELAY=3
+CONFIG_DEFAULT_FDT_FILE="imx6ul-isiot-emmc.dtb"
+CONFIG_SPL=y
+CONFIG_HUSH_PARSER=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_SYS_PROMPT="isiotmx6ul> "
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+# CONFIG_BLK is not set
+# CONFIG_DM_MMC_OPS is not set
+CONFIG_FEC_MXC=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_MXC_UART=y
+CONFIG_IMX_THERMAL=y
diff --git a/include/configs/imx6ul_isiot.h b/include/configs/imx6ul_isiot.h
index 10311d0..1b0e436 100644
--- a/include/configs/imx6ul_isiot.h
+++ b/include/configs/imx6ul_isiot.h
@@ -145,7 +145,7 @@
/* MMC */
#ifdef CONFIG_FSL_USDHC
# define CONFIG_SYS_MMC_ENV_DEV 0
-# define CONFIG_SYS_FSL_USDHC_NUM 1
+# define CONFIG_SYS_FSL_USDHC_NUM 2
# define CONFIG_SYS_FSL_ESDHC_ADDR 0
#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 07/15] i.MX6UL: isiot: Add modeboot env via board_late_init
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (5 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 06/15] i.MX6UL: isiot: Add eMMC boot support Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 08/15] i.MX6UL: isiot: Add mmc_late_init Jagan Teki
` (7 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/isiotmx6ul/isiotmx6ul.c | 21 ++++++++++++++++++++
configs/imx6ul_isiot_emmc_defconfig | 1 +
configs/imx6ul_isiot_mmc_defconfig | 1 +
configs/imx6ul_isiot_nand_defconfig | 1 +
include/configs/imx6ul_isiot.h | 36 ++++++++++++++++-------------------
5 files changed, 40 insertions(+), 20 deletions(-)
diff --git a/board/engicam/isiotmx6ul/isiotmx6ul.c b/board/engicam/isiotmx6ul/isiotmx6ul.c
index 17c19e0..3fc5bca 100644
--- a/board/engicam/isiotmx6ul/isiotmx6ul.c
+++ b/board/engicam/isiotmx6ul/isiotmx6ul.c
@@ -103,6 +103,27 @@ static void setup_gpmi_nand(void)
}
#endif /* CONFIG_NAND_MXS */
+int board_late_init(void)
+{
+ switch ((imx6_src_get_boot_mode() & IMX6_BMODE_MASK) >>
+ IMX6_BMODE_SHIFT) {
+ case IMX6_BMODE_SD:
+ case IMX6_BMODE_ESD:
+ case IMX6_BMODE_MMC:
+ case IMX6_BMODE_EMMC:
+ setenv("modeboot", "mmcboot");
+ break;
+ case IMX6_BMODE_NAND:
+ setenv("modeboot", "nandboot");
+ break;
+ default:
+ setenv("modeboot", "");
+ break;
+ }
+
+ return 0;
+}
+
int board_init(void)
{
/* Address of boot parameters */
diff --git a/configs/imx6ul_isiot_emmc_defconfig b/configs/imx6ul_isiot_emmc_defconfig
index 94fe808..4c3664f 100644
--- a/configs/imx6ul_isiot_emmc_defconfig
+++ b/configs/imx6ul_isiot_emmc_defconfig
@@ -37,3 +37,4 @@ CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_MXC_UART=y
CONFIG_IMX_THERMAL=y
+CONFIG_BOARD_LATE_INIT=y
diff --git a/configs/imx6ul_isiot_mmc_defconfig b/configs/imx6ul_isiot_mmc_defconfig
index 8ecdd8e..ea2d378 100644
--- a/configs/imx6ul_isiot_mmc_defconfig
+++ b/configs/imx6ul_isiot_mmc_defconfig
@@ -39,3 +39,4 @@ CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_MXC_UART=y
CONFIG_IMX_THERMAL=y
+CONFIG_BOARD_LATE_INIT=y
diff --git a/configs/imx6ul_isiot_nand_defconfig b/configs/imx6ul_isiot_nand_defconfig
index 6f1a054..f02a2ac 100644
--- a/configs/imx6ul_isiot_nand_defconfig
+++ b/configs/imx6ul_isiot_nand_defconfig
@@ -40,3 +40,4 @@ CONFIG_PINCTRL_IMX6=y
CONFIG_SYS_I2C_MXC=y
CONFIG_MXC_UART=y
CONFIG_IMX_THERMAL=y
+CONFIG_BOARD_LATE_INIT=y
diff --git a/include/configs/imx6ul_isiot.h b/include/configs/imx6ul_isiot.h
index 1b0e436..7258fed 100644
--- a/include/configs/imx6ul_isiot.h
+++ b/include/configs/imx6ul_isiot.h
@@ -64,8 +64,7 @@
"fitboot=echo Booting FIT image from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
+ "_mmcboot=run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
"bootm ${loadaddr} - ${fdt_addr}; " \
@@ -79,6 +78,20 @@
"else " \
"bootm; " \
"fi\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadfit; then " \
+ "run fitboot; " \
+ "else " \
+ "if run loadimage; then " \
+ "run _mmcboot; " \
+ "fi; " \
+ "fi; " \
+ "fi; " \
+ "fi\0" \
"nandboot=echo Booting from nand ...; " \
"if mtdparts; then " \
"echo Starting nand boot ...; " \
@@ -90,24 +103,7 @@
"nand read ${fdt_addr} dtb 0x100000; " \
"bootm ${loadaddr} - ${fdt_addr}\0"
-#ifdef CONFIG_NAND_MXS
-# define CONFIG_BOOTCOMMAND "run nandboot"
-#else
-# define CONFIG_BOOTCOMMAND \
- "if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadfit; then " \
- "run fitboot; " \
- "else " \
- "if run loadimage; then " \
- "run mmcboot; " \
- "fi; " \
- "fi; " \
- "fi; " \
- "fi"
-#endif
+#define CONFIG_BOOTCOMMAND "run $modeboot"
/* Miscellaneous configurable options */
#define CONFIG_SYS_MEMTEST_START 0x80000000
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 08/15] i.MX6UL: isiot: Add mmc_late_init
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (6 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 07/15] i.MX6UL: isiot: Add modeboot env via board_late_init Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 09/15] i.MX6UL: isiot: Switch the mmc env based on devno Jagan Teki
` (6 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/isiotmx6ul/isiotmx6ul.c | 22 ++++++++++++++++++++++
include/configs/imx6ul_isiot.h | 2 --
2 files changed, 22 insertions(+), 2 deletions(-)
diff --git a/board/engicam/isiotmx6ul/isiotmx6ul.c b/board/engicam/isiotmx6ul/isiotmx6ul.c
index 3fc5bca..920d317 100644
--- a/board/engicam/isiotmx6ul/isiotmx6ul.c
+++ b/board/engicam/isiotmx6ul/isiotmx6ul.c
@@ -7,6 +7,7 @@
*/
#include <common.h>
+#include <mmc.h>
#include <asm/io.h>
#include <asm/gpio.h>
@@ -103,6 +104,24 @@ static void setup_gpmi_nand(void)
}
#endif /* CONFIG_NAND_MXS */
+#ifdef CONFIG_ENV_IS_IN_MMC
+static void mmc_late_init(void)
+{
+ char cmd[32];
+ char mmcblk[32];
+ u32 dev_no = mmc_get_env_dev();
+
+ setenv_ulong("mmcdev", dev_no);
+
+ /* Set mmcblk env */
+ sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw", dev_no);
+ setenv("mmcroot", mmcblk);
+
+ sprintf(cmd, "mmc dev %d", dev_no);
+ run_command(cmd, 0);
+}
+#endif
+
int board_late_init(void)
{
switch ((imx6_src_get_boot_mode() & IMX6_BMODE_MASK) >>
@@ -111,6 +130,9 @@ int board_late_init(void)
case IMX6_BMODE_ESD:
case IMX6_BMODE_MMC:
case IMX6_BMODE_EMMC:
+#ifdef CONFIG_ENV_IS_IN_MMC
+ mmc_late_init();
+#endif
setenv("modeboot", "mmcboot");
break;
case IMX6_BMODE_NAND:
diff --git a/include/configs/imx6ul_isiot.h b/include/configs/imx6ul_isiot.h
index 7258fed..4009648 100644
--- a/include/configs/imx6ul_isiot.h
+++ b/include/configs/imx6ul_isiot.h
@@ -45,9 +45,7 @@
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"fdt_addr=0x87800000\0" \
"boot_fdt=try\0" \
- "mmcdev=0\0" \
"mmcpart=1\0" \
- "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
"nandroot=ubi0:rootfs rootfstype=ubifs\0" \
"mmcautodetect=yes\0" \
"mmcargs=setenv bootargs console=${console},${baudrate} " \
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 09/15] i.MX6UL: isiot: Switch the mmc env based on devno
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (7 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 08/15] i.MX6UL: isiot: Add mmc_late_init Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 10/15] arm: dts: imx6qdl-icore-rqs: Add eMMC node Jagan Teki
` (5 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add board_mmc_get_env_dev
Switch the mmc env based on the mmc devno, instead of separately
defining a config item in include/configs using board_mmc_get_env_dev
- devno 0: sd/esd
- devno 1: mmc/emmc
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/isiotmx6ul/isiotmx6ul.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/board/engicam/isiotmx6ul/isiotmx6ul.c b/board/engicam/isiotmx6ul/isiotmx6ul.c
index 920d317..df432a1 100644
--- a/board/engicam/isiotmx6ul/isiotmx6ul.c
+++ b/board/engicam/isiotmx6ul/isiotmx6ul.c
@@ -105,6 +105,12 @@ static void setup_gpmi_nand(void)
#endif /* CONFIG_NAND_MXS */
#ifdef CONFIG_ENV_IS_IN_MMC
+int board_mmc_get_env_dev(int devno)
+{
+ /* dev 0 for SD/eSD, dev 1 for MMC/eMMC */
+ return (devno == 0) ? 0 : 1;
+}
+
static void mmc_late_init(void)
{
char cmd[32];
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 10/15] arm: dts: imx6qdl-icore-rqs: Add eMMC node
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (8 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 09/15] i.MX6UL: isiot: Switch the mmc env based on devno Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 11/15] imx6: icorem6_rqs: Update SPL board boot order for eMMC Jagan Teki
` (4 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
Add usdhc4 node, which is eMMC for Engicam i.CoreM6 RQS modules.
eMMC Log:
--------
icorem6qdl-rqs> mmc dev 1
switch to partitions #0, OK
mmc1(part 0) is current device
icorem6qdl-rqs> mmcinfo
Device: FSL_SDHC
Manufacturer ID: fe
OEM: 14e
Name: MMC04
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.4.1
High Capacity: Yes
Capacity: 3.5 GiB
Bus Width: 4-bit
Erase Group Size: 512 KiB
HC WP Group Size: 4 MiB
User Capacity: 3.5 GiB
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
arch/arm/dts/imx6qdl-icore-rqs.dtsi | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/arch/arm/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/dts/imx6qdl-icore-rqs.dtsi
index 750229b..8b9d5b4 100644
--- a/arch/arm/dts/imx6qdl-icore-rqs.dtsi
+++ b/arch/arm/dts/imx6qdl-icore-rqs.dtsi
@@ -107,6 +107,13 @@
status = "okay";
};
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ no-1-8-v;
+ status = "okay";
+};
+
&iomuxc {
pinctrl_enet: enetgrp {
fsl,pins = <
@@ -167,4 +174,19 @@
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17070
>;
};
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17070
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10070
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17070
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17070
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17070
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17070
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17070
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17070
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17070
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17070
+ >;
+ };
};
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 11/15] imx6: icorem6_rqs: Update SPL board boot order for eMMC
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (9 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 10/15] arm: dts: imx6qdl-icore-rqs: Add eMMC node Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 12/15] imx6: icorem6_rqs: Add eMMC boot support Jagan Teki
` (3 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
SPL mmc device index is get based on the boot device, like
- BOOT_DEVICE_MMC1 for mmc device 0
- BOOT_DEVICE_MMC2 for mmc device 1
Currently BOOT_DEVICE_MMC1 is setting both SD/eSD and MMC/eMMC
boot devices in i.MX, So u-boot is loading from mmc device 0 even
"if the board booting from SD/eSD or MMC/eMMC"
So, this patch set BOOT_DEVICE_MMC2 for MMC/eMMC so for MMC/eMMC
the u-boot is loading from mmc device 1 and the board file need to
take care if the board have different mmc device order intialization.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/icorem6_rqs/icorem6_rqs.c | 26 ++++++++++++++++++++++++++
1 file changed, 26 insertions(+)
diff --git a/board/engicam/icorem6_rqs/icorem6_rqs.c b/board/engicam/icorem6_rqs/icorem6_rqs.c
index 2769177..e3c520f 100644
--- a/board/engicam/icorem6_rqs/icorem6_rqs.c
+++ b/board/engicam/icorem6_rqs/icorem6_rqs.c
@@ -125,6 +125,32 @@ int board_mmc_init(bd_t *bis)
return 0;
}
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+void board_boot_order(u32 *spl_boot_list)
+{
+ u32 bmode = imx6_src_get_boot_mode();
+ u8 boot_dev = BOOT_DEVICE_MMC1;
+
+ switch ((bmode & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
+ case IMX6_BMODE_SD:
+ case IMX6_BMODE_ESD:
+ /* SD/eSD - BOOT_DEVICE_MMC1 */
+ break;
+ case IMX6_BMODE_MMC:
+ case IMX6_BMODE_EMMC:
+ /* MMC/eMMC */
+ boot_dev = BOOT_DEVICE_MMC2;
+ break;
+ default:
+ /* Default - BOOT_DEVICE_MMC1 */
+ printf("Wrong board boot order\n");
+ break;
+ }
+
+ spl_boot_list[0] = boot_dev;
+}
+#endif
#endif
/*
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 12/15] imx6: icorem6_rqs: Add eMMC boot support
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (10 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 11/15] imx6: icorem6_rqs: Update SPL board boot order for eMMC Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 13/15] i.MX6Q: icorem6_rqs: Add modeboot env via board_late_init Jagan Teki
` (2 subsequent siblings)
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Boot from eMMC:
--------------
U-Boot SPL 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21)
Trying to boot from MMC2
U-Boot 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21 +0100)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
switch to partitions #0, OK
mmc1(part 0) is current device
Net: No ethernet found.
Hit any key to stop autoboot: 0
Booting from mmc ...
switch to partitions #0, OK
mmc1(part 0) is current device
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/icorem6_rqs/icorem6_rqs.c | 24 ++++++++++++++++++++++--
include/configs/imx6qdl_icore_rqs.h | 2 +-
2 files changed, 23 insertions(+), 3 deletions(-)
diff --git a/board/engicam/icorem6_rqs/icorem6_rqs.c b/board/engicam/icorem6_rqs/icorem6_rqs.c
index e3c520f..66cf487 100644
--- a/board/engicam/icorem6_rqs/icorem6_rqs.c
+++ b/board/engicam/icorem6_rqs/icorem6_rqs.c
@@ -77,8 +77,22 @@ static iomux_v3_cfg_t const usdhc3_pads[] = {
IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
};
-struct fsl_esdhc_cfg usdhc_cfg[1] = {
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+ IOMUX_PADS(PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+};
+
+struct fsl_esdhc_cfg usdhc_cfg[2] = {
{USDHC3_BASE_ADDR, 1, 4},
+ {USDHC4_BASE_ADDR, 1, 8},
};
int board_mmc_getcd(struct mmc *mmc)
@@ -88,6 +102,7 @@ int board_mmc_getcd(struct mmc *mmc)
switch (cfg->esdhc_base) {
case USDHC3_BASE_ADDR:
+ case USDHC4_BASE_ADDR:
ret = 1;
break;
}
@@ -102,7 +117,8 @@ int board_mmc_init(bd_t *bis)
/*
* According to the board_mmc_init() the following map is done:
* (U-boot device node) (Physical Port)
- * mmc0 USDHC3
+ * mmc0 USDHC3
+ * mmc1 USDHC4
*/
for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
switch (i) {
@@ -110,6 +126,10 @@ int board_mmc_init(bd_t *bis)
SETUP_IOMUX_PADS(usdhc3_pads);
usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
break;
+ case 1:
+ SETUP_IOMUX_PADS(usdhc4_pads);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+ break;
default:
printf("Warning - USDHC%d controller not supporting\n",
i + 1);
diff --git a/include/configs/imx6qdl_icore_rqs.h b/include/configs/imx6qdl_icore_rqs.h
index 6f7195d..cd94c5f 100644
--- a/include/configs/imx6qdl_icore_rqs.h
+++ b/include/configs/imx6qdl_icore_rqs.h
@@ -124,7 +124,7 @@
/* MMC */
#ifdef CONFIG_FSL_USDHC
# define CONFIG_SYS_MMC_ENV_DEV 0
-# define CONFIG_SYS_FSL_USDHC_NUM 1
+# define CONFIG_SYS_FSL_USDHC_NUM 2
# define CONFIG_SYS_FSL_ESDHC_ADDR 0
#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 13/15] i.MX6Q: icorem6_rqs: Add modeboot env via board_late_init
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (11 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 12/15] imx6: icorem6_rqs: Add eMMC boot support Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 14/15] i.MX6Q: icorem6_rqs: Add mmc_late_init Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 15/15] i.MX6Q: isiot: Switch the mmc env based on devno Jagan Teki
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot based
on the bootdevice so-that conditional macros for MMC via
CONFIG_BOOTCOMMAND should be avoided in config files.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/icorem6_rqs/icorem6_rqs.c | 18 ++++++++++++++++++
configs/imx6dl_icore_rqs_mmc_defconfig | 1 +
configs/imx6q_icore_rqs_mmc_defconfig | 1 +
include/configs/imx6qdl_icore_rqs.h | 32 ++++++++++++++++----------------
4 files changed, 36 insertions(+), 16 deletions(-)
diff --git a/board/engicam/icorem6_rqs/icorem6_rqs.c b/board/engicam/icorem6_rqs/icorem6_rqs.c
index 66cf487..4bb43d1 100644
--- a/board/engicam/icorem6_rqs/icorem6_rqs.c
+++ b/board/engicam/icorem6_rqs/icorem6_rqs.c
@@ -45,6 +45,24 @@ int board_init(void)
return 0;
}
+int board_late_init(void)
+{
+ switch ((imx6_src_get_boot_mode() & IMX6_BMODE_MASK) >>
+ IMX6_BMODE_SHIFT) {
+ case IMX6_BMODE_SD:
+ case IMX6_BMODE_ESD:
+ case IMX6_BMODE_MMC:
+ case IMX6_BMODE_EMMC:
+ setenv("modeboot", "mmcboot");
+ break;
+ default:
+ setenv("modeboot", "");
+ break;
+ }
+
+ return 0;
+}
+
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
diff --git a/configs/imx6dl_icore_rqs_mmc_defconfig b/configs/imx6dl_icore_rqs_mmc_defconfig
index 3b10e99..b15fcb2 100644
--- a/configs/imx6dl_icore_rqs_mmc_defconfig
+++ b/configs/imx6dl_icore_rqs_mmc_defconfig
@@ -38,3 +38,4 @@ CONFIG_FEC_MXC=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_MXC_UART=y
+CONFIG_BOARD_LATE_INIT=y
diff --git a/configs/imx6q_icore_rqs_mmc_defconfig b/configs/imx6q_icore_rqs_mmc_defconfig
index 8df4ef0..987fdf7 100644
--- a/configs/imx6q_icore_rqs_mmc_defconfig
+++ b/configs/imx6q_icore_rqs_mmc_defconfig
@@ -38,3 +38,4 @@ CONFIG_FEC_MXC=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_MXC_UART=y
+CONFIG_BOARD_LATE_INIT=y
diff --git a/include/configs/imx6qdl_icore_rqs.h b/include/configs/imx6qdl_icore_rqs.h
index cd94c5f..c62c1d4 100644
--- a/include/configs/imx6qdl_icore_rqs.h
+++ b/include/configs/imx6qdl_icore_rqs.h
@@ -56,8 +56,7 @@
"fitboot=echo Booting FIT image from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
+ "_mmcboot=run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
"bootm ${loadaddr} - ${fdt_addr}; " \
@@ -70,23 +69,24 @@
"fi; " \
"else " \
"bootm; " \
- "fi\0"
-
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev};" \
- "if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadfit; then " \
- "run fitboot; " \
+ "fi\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "mmc dev ${mmcdev};" \
+ "if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
"else " \
- "if run loadimage; then " \
- "run mmcboot; " \
+ "if run loadfit; then " \
+ "run fitboot; " \
+ "else " \
+ "if run loadimage; then " \
+ "run _mmcboot; " \
+ "fi; " \
"fi; " \
"fi; " \
- "fi; " \
- "fi"
+ "fi\0"
+
+#define CONFIG_BOOTCOMMAND "run $modeboot"
/* Miscellaneous configurable options */
#define CONFIG_SYS_MEMTEST_START 0x80000000
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 14/15] i.MX6Q: icorem6_rqs: Add mmc_late_init
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (12 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 13/15] i.MX6Q: icorem6_rqs: Add modeboot env via board_late_init Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
2017-01-27 14:12 ` [U-Boot] [PATCH v2 15/15] i.MX6Q: isiot: Switch the mmc env based on devno Jagan Teki
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/icorem6_rqs/icorem6_rqs.c | 22 ++++++++++++++++++++++
include/configs/imx6qdl_icore_rqs.h | 2 --
2 files changed, 22 insertions(+), 2 deletions(-)
diff --git a/board/engicam/icorem6_rqs/icorem6_rqs.c b/board/engicam/icorem6_rqs/icorem6_rqs.c
index 4bb43d1..f289e91 100644
--- a/board/engicam/icorem6_rqs/icorem6_rqs.c
+++ b/board/engicam/icorem6_rqs/icorem6_rqs.c
@@ -7,6 +7,7 @@
*/
#include <common.h>
+#include <mmc.h>
#include <asm/io.h>
#include <asm/gpio.h>
@@ -45,6 +46,24 @@ int board_init(void)
return 0;
}
+#ifdef CONFIG_ENV_IS_IN_MMC
+static void mmc_late_init(void)
+{
+ char cmd[32];
+ char mmcblk[32];
+ u32 dev_no = mmc_get_env_dev();
+
+ setenv_ulong("mmcdev", dev_no);
+
+ /* Set mmcblk env */
+ sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw", dev_no);
+ setenv("mmcroot", mmcblk);
+
+ sprintf(cmd, "mmc dev %d", dev_no);
+ run_command(cmd, 0);
+}
+#endif
+
int board_late_init(void)
{
switch ((imx6_src_get_boot_mode() & IMX6_BMODE_MASK) >>
@@ -53,6 +72,9 @@ int board_late_init(void)
case IMX6_BMODE_ESD:
case IMX6_BMODE_MMC:
case IMX6_BMODE_EMMC:
+#ifdef CONFIG_ENV_IS_IN_MMC
+ mmc_late_init();
+#endif
setenv("modeboot", "mmcboot");
break;
default:
diff --git a/include/configs/imx6qdl_icore_rqs.h b/include/configs/imx6qdl_icore_rqs.h
index c62c1d4..3358320 100644
--- a/include/configs/imx6qdl_icore_rqs.h
+++ b/include/configs/imx6qdl_icore_rqs.h
@@ -40,9 +40,7 @@
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"fdt_addr=0x18000000\0" \
"boot_fdt=try\0" \
- "mmcdev=0\0" \
"mmcpart=1\0" \
- "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
"mmcautodetect=yes\0" \
"mmcargs=setenv bootargs console=${console},${baudrate} " \
"root=${mmcroot}\0" \
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [U-Boot] [PATCH v2 15/15] i.MX6Q: isiot: Switch the mmc env based on devno
2017-01-27 14:12 [U-Boot] [PATC v2 00/15] imx6: Engicam i.CoreM6/Is.IoT eMMC boot support Jagan Teki
` (13 preceding siblings ...)
2017-01-27 14:12 ` [U-Boot] [PATCH v2 14/15] i.MX6Q: icorem6_rqs: Add mmc_late_init Jagan Teki
@ 2017-01-27 14:12 ` Jagan Teki
14 siblings, 0 replies; 22+ messages in thread
From: Jagan Teki @ 2017-01-27 14:12 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Add board_mmc_get_env_dev
Switch the mmc env based on the mmc devno, instead of separately
defining a config item in include/configs using board_mmc_get_env_dev
- devno 0: sd/esd
- devno 1: mmc/emmc
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
board/engicam/icorem6_rqs/icorem6_rqs.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/board/engicam/icorem6_rqs/icorem6_rqs.c b/board/engicam/icorem6_rqs/icorem6_rqs.c
index f289e91..d2f9309 100644
--- a/board/engicam/icorem6_rqs/icorem6_rqs.c
+++ b/board/engicam/icorem6_rqs/icorem6_rqs.c
@@ -47,6 +47,12 @@ int board_init(void)
}
#ifdef CONFIG_ENV_IS_IN_MMC
+int board_mmc_get_env_dev(int devno)
+{
+ /* dev 0 for SD/eSD, dev 1 for MMC/eMMC */
+ return (devno == 3) ? 1 : 0;
+}
+
static void mmc_late_init(void)
{
char cmd[32];
--
1.9.1
^ permalink raw reply related [flat|nested] 22+ messages in thread