* [PATCH v8 3/3] thermal: zx2967: add thermal driver for ZTE's zx2967 family
@ 2017-02-04 3:39 ` Baoyou Xie
0 siblings, 0 replies; 10+ messages in thread
From: Baoyou Xie @ 2017-02-04 3:39 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds thermal driver for ZTE's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
---
drivers/thermal/Kconfig | 8 ++
drivers/thermal/Makefile | 1 +
drivers/thermal/zx2967_thermal.c | 255 +++++++++++++++++++++++++++++++++++++++
3 files changed, 264 insertions(+)
create mode 100644 drivers/thermal/zx2967_thermal.c
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 18f2de6..f64bd50 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -444,4 +444,12 @@ config BCM2835_THERMAL
help
Support for thermal sensors on Broadcom bcm2835 SoCs.
+config ZX2967_THERMAL
+ tristate "Thermal sensors on zx2967 SoC"
+ depends on ARCH_ZX || COMPILE_TEST
+ help
+ Enable the zx2967 thermal sensors driver, which supports
+ the primitive temperature sensor embedded in zx2967 SoCs.
+ This sensor generates the real time die temperature.
+
endif
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 677c6d9..c00c05e 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -57,3 +57,4 @@ obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o
obj-$(CONFIG_GENERIC_ADC_THERMAL) += thermal-generic-adc.o
obj-$(CONFIG_BCM2835_THERMAL) += bcm2835_thermal.o
+obj-$(CONFIG_ZX2967_THERMAL) += zx2967_thermal.o
diff --git a/drivers/thermal/zx2967_thermal.c b/drivers/thermal/zx2967_thermal.c
new file mode 100644
index 0000000..d177238
--- /dev/null
+++ b/drivers/thermal/zx2967_thermal.c
@@ -0,0 +1,255 @@
+/*
+ * ZTE's zx2967 family thermal sensor driver
+ *
+ * Copyright (C) 2017 ZTE Ltd.
+ *
+ * Author: Baoyou Xie <baoyou.xie@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/thermal.h>
+
+/* Power Mode: 0->low 1->high */
+#define ZX2967_THERMAL_POWER_MODE 0
+#define ZX2967_POWER_MODE_LOW 0
+#define ZX2967_POWER_MODE_HIGH 1
+
+/* DCF Control Register */
+#define ZX2967_THERMAL_DCF 0x4
+#define ZX2967_DCF_EN BIT(1)
+#define ZX2967_DCF_FREEZE BIT(0)
+
+/* Selection Register */
+#define ZX2967_THERMAL_SEL 0x8
+
+/* Control Register */
+#define ZX2967_THERMAL_CTRL 0x10
+
+#define ZX2967_THERMAL_READY BIT(12)
+#define ZX2967_THERMAL_TEMP_MASK GENMASK(11, 0)
+#define ZX2967_THERMAL_ID_MASK 0x18
+#define ZX2967_THERMAL_ID 0x10
+
+#define ZX2967_GET_TEMP_TIMEOUT_US (100 * 1024)
+
+/* zx2967 Thermal Sensor Private Structure */
+struct zx2967_thermal_priv {
+ /* struct thermal_zone_device where the sensor is registered */
+ struct thermal_zone_device *tzd;
+ /* prevents reads sensor in parallel */
+ struct mutex lock;
+ /* topcrm clk structure */
+ struct clk *clk_topcrm;
+ /* apb clk structure */
+ struct clk *clk_apb;
+ /* pointer to base address of the thermal sensor */
+ void __iomem *regs;
+ struct device *dev;
+};
+
+static int zx2967_thermal_get_temp(void *data, int *temp)
+{
+ void __iomem *regs;
+ struct zx2967_thermal_priv *priv = data;
+ u32 val;
+ int ret;
+
+ if (!priv->tzd)
+ return -EAGAIN;
+
+ regs = priv->regs;
+ mutex_lock(&priv->lock);
+ writel_relaxed(ZX2967_POWER_MODE_LOW,
+ regs + ZX2967_THERMAL_POWER_MODE);
+ writel_relaxed(ZX2967_DCF_EN, regs + ZX2967_THERMAL_DCF);
+
+ val = readl_relaxed(regs + ZX2967_THERMAL_SEL);
+ val &= ~ZX2967_THERMAL_ID_MASK;
+ val |= ZX2967_THERMAL_ID;
+ writel_relaxed(val, regs + ZX2967_THERMAL_SEL);
+
+ /*
+ * Must wait for a while, surely it's a bit odd.
+ * otherwise temperature value we got has a few deviation, even if
+ * the THERMAL_READY bit is set.
+ */
+ usleep_range(100, 300);
+ ret = readx_poll_timeout(readl, regs + ZX2967_THERMAL_CTRL,
+ val, val & ZX2967_THERMAL_READY, 300,
+ ZX2967_GET_TEMP_TIMEOUT_US);
+ if (ret) {
+ dev_err(priv->dev, "Thermal sensor data timeout\n");
+ goto unlock;
+ }
+
+ writel_relaxed(ZX2967_DCF_FREEZE | ZX2967_DCF_EN,
+ regs + ZX2967_THERMAL_DCF);
+ val = readl_relaxed(regs + ZX2967_THERMAL_CTRL)
+ & ZX2967_THERMAL_TEMP_MASK;
+ writel_relaxed(ZX2967_POWER_MODE_HIGH,
+ regs + ZX2967_THERMAL_POWER_MODE);
+
+ /*
+ * Calculate temperature
+ * In dts, slope is multiplied by 1000.
+ */
+ *temp = DIV_ROUND_CLOSEST(((s32)val + priv->tzd->tzp->offset) * 1000,
+ priv->tzd->tzp->slope);
+
+unlock:
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static struct thermal_zone_of_device_ops zx2967_of_thermal_ops = {
+ .get_temp = zx2967_thermal_get_temp,
+};
+
+static int zx2967_thermal_probe(struct platform_device *pdev)
+{
+ struct zx2967_thermal_priv *priv;
+ struct resource *res;
+ int ret;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(priv->regs))
+ return PTR_ERR(priv->regs);
+
+ priv->clk_topcrm = devm_clk_get(&pdev->dev, "topcrm");
+ if (IS_ERR(priv->clk_topcrm)) {
+ ret = PTR_ERR(priv->clk_topcrm);
+ dev_err(&pdev->dev, "failed to get topcrm clock: %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(priv->clk_topcrm);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to enable topcrm clock: %d\n",
+ ret);
+ return ret;
+ }
+
+ priv->clk_apb = devm_clk_get(&pdev->dev, "apb");
+ if (IS_ERR(priv->clk_apb)) {
+ ret = PTR_ERR(priv->clk_apb);
+ dev_err(&pdev->dev, "failed to get apb clock: %d\n", ret);
+ goto disable_clk_topcrm;
+ }
+
+ ret = clk_prepare_enable(priv->clk_apb);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to enable apb clock: %d\n",
+ ret);
+ goto disable_clk_topcrm;
+ }
+
+ mutex_init(&priv->lock);
+ priv->tzd = thermal_zone_of_sensor_register(&pdev->dev,
+ 0, priv, &zx2967_of_thermal_ops);
+
+ if (IS_ERR(priv->tzd)) {
+ ret = PTR_ERR(priv->tzd);
+ dev_err(&pdev->dev, "failed to register sensor: %d\n", ret);
+ goto disable_clk_all;
+ }
+
+ if (priv->tzd->tzp->slope == 0) {
+ thermal_zone_of_sensor_unregister(&pdev->dev, priv->tzd);
+ dev_err(&pdev->dev, "coefficients of sensor is invalid\n");
+ ret = -EINVAL;
+ goto disable_clk_all;
+ }
+
+ priv->dev = &pdev->dev;
+ platform_set_drvdata(pdev, priv);
+
+ return 0;
+
+disable_clk_all:
+ clk_disable_unprepare(priv->clk_apb);
+disable_clk_topcrm:
+ clk_disable_unprepare(priv->clk_topcrm);
+ return ret;
+}
+
+static int zx2967_thermal_exit(struct platform_device *pdev)
+{
+ struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
+
+ thermal_zone_of_sensor_unregister(&pdev->dev, priv->tzd);
+ clk_disable_unprepare(priv->clk_topcrm);
+ clk_disable_unprepare(priv->clk_apb);
+
+ return 0;
+}
+
+static const struct of_device_id zx2967_thermal_id_table[] = {
+ { .compatible = "zte,zx296718-thermal" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, zx2967_thermal_id_table);
+
+#ifdef CONFIG_PM_SLEEP
+static int zx2967_thermal_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
+
+ if (priv && priv->clk_topcrm)
+ clk_disable_unprepare(priv->clk_topcrm);
+
+ if (priv && priv->clk_apb)
+ clk_disable_unprepare(priv->clk_apb);
+
+ return 0;
+}
+
+static int zx2967_thermal_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
+ int error;
+
+ error = clk_prepare_enable(priv->clk_topcrm);
+ if (error)
+ return error;
+
+ error = clk_prepare_enable(priv->clk_apb);
+ if (error) {
+ clk_disable_unprepare(priv->clk_topcrm);
+ return error;
+ }
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(zx2967_thermal_pm_ops,
+ zx2967_thermal_suspend, zx2967_thermal_resume);
+
+static struct platform_driver zx2967_thermal_driver = {
+ .probe = zx2967_thermal_probe,
+ .remove = zx2967_thermal_exit,
+ .driver = {
+ .name = "zx2967_thermal",
+ .of_match_table = zx2967_thermal_id_table,
+ .pm = &zx2967_thermal_pm_ops,
+ },
+};
+module_platform_driver(zx2967_thermal_driver);
+
+MODULE_AUTHOR("Baoyou Xie <baoyou.xie@linaro.org>");
+MODULE_DESCRIPTION("ZTE zx2967 thermal driver");
+MODULE_LICENSE("GPL v2");
--
2.7.4
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v8 3/3] thermal: zx2967: add thermal driver for ZTE's zx2967 family
@ 2017-02-04 3:39 ` Baoyou Xie
0 siblings, 0 replies; 10+ messages in thread
From: Baoyou Xie @ 2017-02-04 3:39 UTC (permalink / raw)
To: mathieu.poirier-QSEj5FYQhm4dnm+yROfE0A,
jun.nie-QSEj5FYQhm4dnm+yROfE0A, rui.zhang-ral2JQCrhuEAvxtiuMwx3w,
edubezval-Re5JQEeQqe8AvxtiuMwx3w, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-pm-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
baoyou.xie-QSEj5FYQhm4dnm+yROfE0A,
xie.baoyou-Th6q7B73Y6EnDS1+zs4M5A,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
This patch adds thermal driver for ZTE's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
drivers/thermal/Kconfig | 8 ++
drivers/thermal/Makefile | 1 +
drivers/thermal/zx2967_thermal.c | 255 +++++++++++++++++++++++++++++++++++++++
3 files changed, 264 insertions(+)
create mode 100644 drivers/thermal/zx2967_thermal.c
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 18f2de6..f64bd50 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -444,4 +444,12 @@ config BCM2835_THERMAL
help
Support for thermal sensors on Broadcom bcm2835 SoCs.
+config ZX2967_THERMAL
+ tristate "Thermal sensors on zx2967 SoC"
+ depends on ARCH_ZX || COMPILE_TEST
+ help
+ Enable the zx2967 thermal sensors driver, which supports
+ the primitive temperature sensor embedded in zx2967 SoCs.
+ This sensor generates the real time die temperature.
+
endif
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 677c6d9..c00c05e 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -57,3 +57,4 @@ obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o
obj-$(CONFIG_GENERIC_ADC_THERMAL) += thermal-generic-adc.o
obj-$(CONFIG_BCM2835_THERMAL) += bcm2835_thermal.o
+obj-$(CONFIG_ZX2967_THERMAL) += zx2967_thermal.o
diff --git a/drivers/thermal/zx2967_thermal.c b/drivers/thermal/zx2967_thermal.c
new file mode 100644
index 0000000..d177238
--- /dev/null
+++ b/drivers/thermal/zx2967_thermal.c
@@ -0,0 +1,255 @@
+/*
+ * ZTE's zx2967 family thermal sensor driver
+ *
+ * Copyright (C) 2017 ZTE Ltd.
+ *
+ * Author: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/thermal.h>
+
+/* Power Mode: 0->low 1->high */
+#define ZX2967_THERMAL_POWER_MODE 0
+#define ZX2967_POWER_MODE_LOW 0
+#define ZX2967_POWER_MODE_HIGH 1
+
+/* DCF Control Register */
+#define ZX2967_THERMAL_DCF 0x4
+#define ZX2967_DCF_EN BIT(1)
+#define ZX2967_DCF_FREEZE BIT(0)
+
+/* Selection Register */
+#define ZX2967_THERMAL_SEL 0x8
+
+/* Control Register */
+#define ZX2967_THERMAL_CTRL 0x10
+
+#define ZX2967_THERMAL_READY BIT(12)
+#define ZX2967_THERMAL_TEMP_MASK GENMASK(11, 0)
+#define ZX2967_THERMAL_ID_MASK 0x18
+#define ZX2967_THERMAL_ID 0x10
+
+#define ZX2967_GET_TEMP_TIMEOUT_US (100 * 1024)
+
+/* zx2967 Thermal Sensor Private Structure */
+struct zx2967_thermal_priv {
+ /* struct thermal_zone_device where the sensor is registered */
+ struct thermal_zone_device *tzd;
+ /* prevents reads sensor in parallel */
+ struct mutex lock;
+ /* topcrm clk structure */
+ struct clk *clk_topcrm;
+ /* apb clk structure */
+ struct clk *clk_apb;
+ /* pointer to base address of the thermal sensor */
+ void __iomem *regs;
+ struct device *dev;
+};
+
+static int zx2967_thermal_get_temp(void *data, int *temp)
+{
+ void __iomem *regs;
+ struct zx2967_thermal_priv *priv = data;
+ u32 val;
+ int ret;
+
+ if (!priv->tzd)
+ return -EAGAIN;
+
+ regs = priv->regs;
+ mutex_lock(&priv->lock);
+ writel_relaxed(ZX2967_POWER_MODE_LOW,
+ regs + ZX2967_THERMAL_POWER_MODE);
+ writel_relaxed(ZX2967_DCF_EN, regs + ZX2967_THERMAL_DCF);
+
+ val = readl_relaxed(regs + ZX2967_THERMAL_SEL);
+ val &= ~ZX2967_THERMAL_ID_MASK;
+ val |= ZX2967_THERMAL_ID;
+ writel_relaxed(val, regs + ZX2967_THERMAL_SEL);
+
+ /*
+ * Must wait for a while, surely it's a bit odd.
+ * otherwise temperature value we got has a few deviation, even if
+ * the THERMAL_READY bit is set.
+ */
+ usleep_range(100, 300);
+ ret = readx_poll_timeout(readl, regs + ZX2967_THERMAL_CTRL,
+ val, val & ZX2967_THERMAL_READY, 300,
+ ZX2967_GET_TEMP_TIMEOUT_US);
+ if (ret) {
+ dev_err(priv->dev, "Thermal sensor data timeout\n");
+ goto unlock;
+ }
+
+ writel_relaxed(ZX2967_DCF_FREEZE | ZX2967_DCF_EN,
+ regs + ZX2967_THERMAL_DCF);
+ val = readl_relaxed(regs + ZX2967_THERMAL_CTRL)
+ & ZX2967_THERMAL_TEMP_MASK;
+ writel_relaxed(ZX2967_POWER_MODE_HIGH,
+ regs + ZX2967_THERMAL_POWER_MODE);
+
+ /*
+ * Calculate temperature
+ * In dts, slope is multiplied by 1000.
+ */
+ *temp = DIV_ROUND_CLOSEST(((s32)val + priv->tzd->tzp->offset) * 1000,
+ priv->tzd->tzp->slope);
+
+unlock:
+ mutex_unlock(&priv->lock);
+ return ret;
+}
+
+static struct thermal_zone_of_device_ops zx2967_of_thermal_ops = {
+ .get_temp = zx2967_thermal_get_temp,
+};
+
+static int zx2967_thermal_probe(struct platform_device *pdev)
+{
+ struct zx2967_thermal_priv *priv;
+ struct resource *res;
+ int ret;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(priv->regs))
+ return PTR_ERR(priv->regs);
+
+ priv->clk_topcrm = devm_clk_get(&pdev->dev, "topcrm");
+ if (IS_ERR(priv->clk_topcrm)) {
+ ret = PTR_ERR(priv->clk_topcrm);
+ dev_err(&pdev->dev, "failed to get topcrm clock: %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(priv->clk_topcrm);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to enable topcrm clock: %d\n",
+ ret);
+ return ret;
+ }
+
+ priv->clk_apb = devm_clk_get(&pdev->dev, "apb");
+ if (IS_ERR(priv->clk_apb)) {
+ ret = PTR_ERR(priv->clk_apb);
+ dev_err(&pdev->dev, "failed to get apb clock: %d\n", ret);
+ goto disable_clk_topcrm;
+ }
+
+ ret = clk_prepare_enable(priv->clk_apb);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to enable apb clock: %d\n",
+ ret);
+ goto disable_clk_topcrm;
+ }
+
+ mutex_init(&priv->lock);
+ priv->tzd = thermal_zone_of_sensor_register(&pdev->dev,
+ 0, priv, &zx2967_of_thermal_ops);
+
+ if (IS_ERR(priv->tzd)) {
+ ret = PTR_ERR(priv->tzd);
+ dev_err(&pdev->dev, "failed to register sensor: %d\n", ret);
+ goto disable_clk_all;
+ }
+
+ if (priv->tzd->tzp->slope == 0) {
+ thermal_zone_of_sensor_unregister(&pdev->dev, priv->tzd);
+ dev_err(&pdev->dev, "coefficients of sensor is invalid\n");
+ ret = -EINVAL;
+ goto disable_clk_all;
+ }
+
+ priv->dev = &pdev->dev;
+ platform_set_drvdata(pdev, priv);
+
+ return 0;
+
+disable_clk_all:
+ clk_disable_unprepare(priv->clk_apb);
+disable_clk_topcrm:
+ clk_disable_unprepare(priv->clk_topcrm);
+ return ret;
+}
+
+static int zx2967_thermal_exit(struct platform_device *pdev)
+{
+ struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
+
+ thermal_zone_of_sensor_unregister(&pdev->dev, priv->tzd);
+ clk_disable_unprepare(priv->clk_topcrm);
+ clk_disable_unprepare(priv->clk_apb);
+
+ return 0;
+}
+
+static const struct of_device_id zx2967_thermal_id_table[] = {
+ { .compatible = "zte,zx296718-thermal" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, zx2967_thermal_id_table);
+
+#ifdef CONFIG_PM_SLEEP
+static int zx2967_thermal_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
+
+ if (priv && priv->clk_topcrm)
+ clk_disable_unprepare(priv->clk_topcrm);
+
+ if (priv && priv->clk_apb)
+ clk_disable_unprepare(priv->clk_apb);
+
+ return 0;
+}
+
+static int zx2967_thermal_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
+ int error;
+
+ error = clk_prepare_enable(priv->clk_topcrm);
+ if (error)
+ return error;
+
+ error = clk_prepare_enable(priv->clk_apb);
+ if (error) {
+ clk_disable_unprepare(priv->clk_topcrm);
+ return error;
+ }
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(zx2967_thermal_pm_ops,
+ zx2967_thermal_suspend, zx2967_thermal_resume);
+
+static struct platform_driver zx2967_thermal_driver = {
+ .probe = zx2967_thermal_probe,
+ .remove = zx2967_thermal_exit,
+ .driver = {
+ .name = "zx2967_thermal",
+ .of_match_table = zx2967_thermal_id_table,
+ .pm = &zx2967_thermal_pm_ops,
+ },
+};
+module_platform_driver(zx2967_thermal_driver);
+
+MODULE_AUTHOR("Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>");
+MODULE_DESCRIPTION("ZTE zx2967 thermal driver");
+MODULE_LICENSE("GPL v2");
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v8 3/3] thermal: zx2967: add thermal driver for ZTE's zx2967 family
2017-02-04 3:39 ` Baoyou Xie
@ 2017-02-06 17:23 ` Mathieu Poirier
-1 siblings, 0 replies; 10+ messages in thread
From: Mathieu Poirier @ 2017-02-06 17:23 UTC (permalink / raw)
To: Baoyou Xie
Cc: jun.nie, rui.zhang, edubezval, robh+dt, mark.rutland,
linux-arm-kernel, linux-pm, devicetree, linux-kernel, shawnguo,
xie.baoyou, chen.chaokai, wang.qiang01
On Sat, Feb 04, 2017 at 11:39:57AM +0800, Baoyou Xie wrote:
> This patch adds thermal driver for ZTE's zx2967 family.
>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
> ---
> drivers/thermal/Kconfig | 8 ++
> drivers/thermal/Makefile | 1 +
> drivers/thermal/zx2967_thermal.c | 255 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 264 insertions(+)
> create mode 100644 drivers/thermal/zx2967_thermal.c
>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index 18f2de6..f64bd50 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -444,4 +444,12 @@ config BCM2835_THERMAL
> help
> Support for thermal sensors on Broadcom bcm2835 SoCs.
>
> +config ZX2967_THERMAL
> + tristate "Thermal sensors on zx2967 SoC"
> + depends on ARCH_ZX || COMPILE_TEST
> + help
> + Enable the zx2967 thermal sensors driver, which supports
> + the primitive temperature sensor embedded in zx2967 SoCs.
> + This sensor generates the real time die temperature.
> +
> endif
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 677c6d9..c00c05e 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -57,3 +57,4 @@ obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
> obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o
> obj-$(CONFIG_GENERIC_ADC_THERMAL) += thermal-generic-adc.o
> obj-$(CONFIG_BCM2835_THERMAL) += bcm2835_thermal.o
> +obj-$(CONFIG_ZX2967_THERMAL) += zx2967_thermal.o
> diff --git a/drivers/thermal/zx2967_thermal.c b/drivers/thermal/zx2967_thermal.c
> new file mode 100644
> index 0000000..d177238
> --- /dev/null
> +++ b/drivers/thermal/zx2967_thermal.c
> @@ -0,0 +1,255 @@
> +/*
> + * ZTE's zx2967 family thermal sensor driver
> + *
> + * Copyright (C) 2017 ZTE Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie@linaro.org>
> + *
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/thermal.h>
> +
> +/* Power Mode: 0->low 1->high */
> +#define ZX2967_THERMAL_POWER_MODE 0
> +#define ZX2967_POWER_MODE_LOW 0
> +#define ZX2967_POWER_MODE_HIGH 1
> +
> +/* DCF Control Register */
> +#define ZX2967_THERMAL_DCF 0x4
> +#define ZX2967_DCF_EN BIT(1)
> +#define ZX2967_DCF_FREEZE BIT(0)
> +
> +/* Selection Register */
> +#define ZX2967_THERMAL_SEL 0x8
> +
> +/* Control Register */
> +#define ZX2967_THERMAL_CTRL 0x10
> +
> +#define ZX2967_THERMAL_READY BIT(12)
> +#define ZX2967_THERMAL_TEMP_MASK GENMASK(11, 0)
> +#define ZX2967_THERMAL_ID_MASK 0x18
> +#define ZX2967_THERMAL_ID 0x10
> +
> +#define ZX2967_GET_TEMP_TIMEOUT_US (100 * 1024)
> +
> +/* zx2967 Thermal Sensor Private Structure */
> +struct zx2967_thermal_priv {
> + /* struct thermal_zone_device where the sensor is registered */
> + struct thermal_zone_device *tzd;
> + /* prevents reads sensor in parallel */
> + struct mutex lock;
> + /* topcrm clk structure */
> + struct clk *clk_topcrm;
> + /* apb clk structure */
> + struct clk *clk_apb;
> + /* pointer to base address of the thermal sensor */
> + void __iomem *regs;
> + struct device *dev;
> +};
Apologies for not being clearer before. The proper way to document a structure
can be found here [1].
[1]. http://lxr.free-electrons.com/source/drivers/thermal/of-thermal.c#L39
> +
> +static int zx2967_thermal_get_temp(void *data, int *temp)
> +{
> + void __iomem *regs;
> + struct zx2967_thermal_priv *priv = data;
> + u32 val;
> + int ret;
> +
> + if (!priv->tzd)
> + return -EAGAIN;
> +
> + regs = priv->regs;
> + mutex_lock(&priv->lock);
> + writel_relaxed(ZX2967_POWER_MODE_LOW,
> + regs + ZX2967_THERMAL_POWER_MODE);
> + writel_relaxed(ZX2967_DCF_EN, regs + ZX2967_THERMAL_DCF);
> +
> + val = readl_relaxed(regs + ZX2967_THERMAL_SEL);
> + val &= ~ZX2967_THERMAL_ID_MASK;
> + val |= ZX2967_THERMAL_ID;
> + writel_relaxed(val, regs + ZX2967_THERMAL_SEL);
> +
> + /*
> + * Must wait for a while, surely it's a bit odd.
> + * otherwise temperature value we got has a few deviation, even if
> + * the THERMAL_READY bit is set.
> + */
> + usleep_range(100, 300);
> + ret = readx_poll_timeout(readl, regs + ZX2967_THERMAL_CTRL,
> + val, val & ZX2967_THERMAL_READY, 300,
> + ZX2967_GET_TEMP_TIMEOUT_US);
> + if (ret) {
> + dev_err(priv->dev, "Thermal sensor data timeout\n");
> + goto unlock;
> + }
> +
> + writel_relaxed(ZX2967_DCF_FREEZE | ZX2967_DCF_EN,
> + regs + ZX2967_THERMAL_DCF);
> + val = readl_relaxed(regs + ZX2967_THERMAL_CTRL)
> + & ZX2967_THERMAL_TEMP_MASK;
> + writel_relaxed(ZX2967_POWER_MODE_HIGH,
> + regs + ZX2967_THERMAL_POWER_MODE);
> +
> + /*
> + * Calculate temperature
> + * In dts, slope is multiplied by 1000.
> + */
> + *temp = DIV_ROUND_CLOSEST(((s32)val + priv->tzd->tzp->offset) * 1000,
> + priv->tzd->tzp->slope);
> +
> +unlock:
> + mutex_unlock(&priv->lock);
> + return ret;
> +}
> +
> +static struct thermal_zone_of_device_ops zx2967_of_thermal_ops = {
> + .get_temp = zx2967_thermal_get_temp,
> +};
> +
> +static int zx2967_thermal_probe(struct platform_device *pdev)
> +{
> + struct zx2967_thermal_priv *priv;
> + struct resource *res;
> + int ret;
> +
> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + priv->regs = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(priv->regs))
> + return PTR_ERR(priv->regs);
> +
> + priv->clk_topcrm = devm_clk_get(&pdev->dev, "topcrm");
> + if (IS_ERR(priv->clk_topcrm)) {
> + ret = PTR_ERR(priv->clk_topcrm);
> + dev_err(&pdev->dev, "failed to get topcrm clock: %d\n", ret);
> + return ret;
> + }
> +
> + ret = clk_prepare_enable(priv->clk_topcrm);
> + if (ret) {
> + dev_err(&pdev->dev, "failed to enable topcrm clock: %d\n",
> + ret);
> + return ret;
> + }
> +
> + priv->clk_apb = devm_clk_get(&pdev->dev, "apb");
> + if (IS_ERR(priv->clk_apb)) {
> + ret = PTR_ERR(priv->clk_apb);
> + dev_err(&pdev->dev, "failed to get apb clock: %d\n", ret);
> + goto disable_clk_topcrm;
> + }
> +
> + ret = clk_prepare_enable(priv->clk_apb);
> + if (ret) {
> + dev_err(&pdev->dev, "failed to enable apb clock: %d\n",
> + ret);
> + goto disable_clk_topcrm;
> + }
> +
> + mutex_init(&priv->lock);
> + priv->tzd = thermal_zone_of_sensor_register(&pdev->dev,
> + 0, priv, &zx2967_of_thermal_ops);
> +
> + if (IS_ERR(priv->tzd)) {
> + ret = PTR_ERR(priv->tzd);
> + dev_err(&pdev->dev, "failed to register sensor: %d\n", ret);
> + goto disable_clk_all;
> + }
> +
> + if (priv->tzd->tzp->slope == 0) {
> + thermal_zone_of_sensor_unregister(&pdev->dev, priv->tzd);
> + dev_err(&pdev->dev, "coefficients of sensor is invalid\n");
> + ret = -EINVAL;
> + goto disable_clk_all;
> + }
> +
> + priv->dev = &pdev->dev;
> + platform_set_drvdata(pdev, priv);
> +
> + return 0;
> +
> +disable_clk_all:
> + clk_disable_unprepare(priv->clk_apb);
> +disable_clk_topcrm:
> + clk_disable_unprepare(priv->clk_topcrm);
> + return ret;
> +}
> +
> +static int zx2967_thermal_exit(struct platform_device *pdev)
> +{
> + struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
> +
> + thermal_zone_of_sensor_unregister(&pdev->dev, priv->tzd);
> + clk_disable_unprepare(priv->clk_topcrm);
> + clk_disable_unprepare(priv->clk_apb);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id zx2967_thermal_id_table[] = {
> + { .compatible = "zte,zx296718-thermal" },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, zx2967_thermal_id_table);
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int zx2967_thermal_suspend(struct device *dev)
> +{
> + struct platform_device *pdev = to_platform_device(dev);
> + struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
> +
> + if (priv && priv->clk_topcrm)
> + clk_disable_unprepare(priv->clk_topcrm);
> +
> + if (priv && priv->clk_apb)
> + clk_disable_unprepare(priv->clk_apb);
> +
> + return 0;
> +}
> +
> +static int zx2967_thermal_resume(struct device *dev)
> +{
> + struct platform_device *pdev = to_platform_device(dev);
> + struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
> + int error;
> +
> + error = clk_prepare_enable(priv->clk_topcrm);
> + if (error)
> + return error;
> +
> + error = clk_prepare_enable(priv->clk_apb);
> + if (error) {
> + clk_disable_unprepare(priv->clk_topcrm);
> + return error;
> + }
> +
> + return 0;
> +}
> +#endif
> +
> +static SIMPLE_DEV_PM_OPS(zx2967_thermal_pm_ops,
> + zx2967_thermal_suspend, zx2967_thermal_resume);
> +
> +static struct platform_driver zx2967_thermal_driver = {
> + .probe = zx2967_thermal_probe,
> + .remove = zx2967_thermal_exit,
> + .driver = {
> + .name = "zx2967_thermal",
> + .of_match_table = zx2967_thermal_id_table,
> + .pm = &zx2967_thermal_pm_ops,
> + },
> +};
> +module_platform_driver(zx2967_thermal_driver);
> +
> +MODULE_AUTHOR("Baoyou Xie <baoyou.xie@linaro.org>");
> +MODULE_DESCRIPTION("ZTE zx2967 thermal driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v8 3/3] thermal: zx2967: add thermal driver for ZTE's zx2967 family
@ 2017-02-06 17:23 ` Mathieu Poirier
0 siblings, 0 replies; 10+ messages in thread
From: Mathieu Poirier @ 2017-02-06 17:23 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Feb 04, 2017 at 11:39:57AM +0800, Baoyou Xie wrote:
> This patch adds thermal driver for ZTE's zx2967 family.
>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
> ---
> drivers/thermal/Kconfig | 8 ++
> drivers/thermal/Makefile | 1 +
> drivers/thermal/zx2967_thermal.c | 255 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 264 insertions(+)
> create mode 100644 drivers/thermal/zx2967_thermal.c
>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index 18f2de6..f64bd50 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -444,4 +444,12 @@ config BCM2835_THERMAL
> help
> Support for thermal sensors on Broadcom bcm2835 SoCs.
>
> +config ZX2967_THERMAL
> + tristate "Thermal sensors on zx2967 SoC"
> + depends on ARCH_ZX || COMPILE_TEST
> + help
> + Enable the zx2967 thermal sensors driver, which supports
> + the primitive temperature sensor embedded in zx2967 SoCs.
> + This sensor generates the real time die temperature.
> +
> endif
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 677c6d9..c00c05e 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -57,3 +57,4 @@ obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
> obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o
> obj-$(CONFIG_GENERIC_ADC_THERMAL) += thermal-generic-adc.o
> obj-$(CONFIG_BCM2835_THERMAL) += bcm2835_thermal.o
> +obj-$(CONFIG_ZX2967_THERMAL) += zx2967_thermal.o
> diff --git a/drivers/thermal/zx2967_thermal.c b/drivers/thermal/zx2967_thermal.c
> new file mode 100644
> index 0000000..d177238
> --- /dev/null
> +++ b/drivers/thermal/zx2967_thermal.c
> @@ -0,0 +1,255 @@
> +/*
> + * ZTE's zx2967 family thermal sensor driver
> + *
> + * Copyright (C) 2017 ZTE Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie@linaro.org>
> + *
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/thermal.h>
> +
> +/* Power Mode: 0->low 1->high */
> +#define ZX2967_THERMAL_POWER_MODE 0
> +#define ZX2967_POWER_MODE_LOW 0
> +#define ZX2967_POWER_MODE_HIGH 1
> +
> +/* DCF Control Register */
> +#define ZX2967_THERMAL_DCF 0x4
> +#define ZX2967_DCF_EN BIT(1)
> +#define ZX2967_DCF_FREEZE BIT(0)
> +
> +/* Selection Register */
> +#define ZX2967_THERMAL_SEL 0x8
> +
> +/* Control Register */
> +#define ZX2967_THERMAL_CTRL 0x10
> +
> +#define ZX2967_THERMAL_READY BIT(12)
> +#define ZX2967_THERMAL_TEMP_MASK GENMASK(11, 0)
> +#define ZX2967_THERMAL_ID_MASK 0x18
> +#define ZX2967_THERMAL_ID 0x10
> +
> +#define ZX2967_GET_TEMP_TIMEOUT_US (100 * 1024)
> +
> +/* zx2967 Thermal Sensor Private Structure */
> +struct zx2967_thermal_priv {
> + /* struct thermal_zone_device where the sensor is registered */
> + struct thermal_zone_device *tzd;
> + /* prevents reads sensor in parallel */
> + struct mutex lock;
> + /* topcrm clk structure */
> + struct clk *clk_topcrm;
> + /* apb clk structure */
> + struct clk *clk_apb;
> + /* pointer to base address of the thermal sensor */
> + void __iomem *regs;
> + struct device *dev;
> +};
Apologies for not being clearer before. The proper way to document a structure
can be found here [1].
[1]. http://lxr.free-electrons.com/source/drivers/thermal/of-thermal.c#L39
> +
> +static int zx2967_thermal_get_temp(void *data, int *temp)
> +{
> + void __iomem *regs;
> + struct zx2967_thermal_priv *priv = data;
> + u32 val;
> + int ret;
> +
> + if (!priv->tzd)
> + return -EAGAIN;
> +
> + regs = priv->regs;
> + mutex_lock(&priv->lock);
> + writel_relaxed(ZX2967_POWER_MODE_LOW,
> + regs + ZX2967_THERMAL_POWER_MODE);
> + writel_relaxed(ZX2967_DCF_EN, regs + ZX2967_THERMAL_DCF);
> +
> + val = readl_relaxed(regs + ZX2967_THERMAL_SEL);
> + val &= ~ZX2967_THERMAL_ID_MASK;
> + val |= ZX2967_THERMAL_ID;
> + writel_relaxed(val, regs + ZX2967_THERMAL_SEL);
> +
> + /*
> + * Must wait for a while, surely it's a bit odd.
> + * otherwise temperature value we got has a few deviation, even if
> + * the THERMAL_READY bit is set.
> + */
> + usleep_range(100, 300);
> + ret = readx_poll_timeout(readl, regs + ZX2967_THERMAL_CTRL,
> + val, val & ZX2967_THERMAL_READY, 300,
> + ZX2967_GET_TEMP_TIMEOUT_US);
> + if (ret) {
> + dev_err(priv->dev, "Thermal sensor data timeout\n");
> + goto unlock;
> + }
> +
> + writel_relaxed(ZX2967_DCF_FREEZE | ZX2967_DCF_EN,
> + regs + ZX2967_THERMAL_DCF);
> + val = readl_relaxed(regs + ZX2967_THERMAL_CTRL)
> + & ZX2967_THERMAL_TEMP_MASK;
> + writel_relaxed(ZX2967_POWER_MODE_HIGH,
> + regs + ZX2967_THERMAL_POWER_MODE);
> +
> + /*
> + * Calculate temperature
> + * In dts, slope is multiplied by 1000.
> + */
> + *temp = DIV_ROUND_CLOSEST(((s32)val + priv->tzd->tzp->offset) * 1000,
> + priv->tzd->tzp->slope);
> +
> +unlock:
> + mutex_unlock(&priv->lock);
> + return ret;
> +}
> +
> +static struct thermal_zone_of_device_ops zx2967_of_thermal_ops = {
> + .get_temp = zx2967_thermal_get_temp,
> +};
> +
> +static int zx2967_thermal_probe(struct platform_device *pdev)
> +{
> + struct zx2967_thermal_priv *priv;
> + struct resource *res;
> + int ret;
> +
> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + priv->regs = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(priv->regs))
> + return PTR_ERR(priv->regs);
> +
> + priv->clk_topcrm = devm_clk_get(&pdev->dev, "topcrm");
> + if (IS_ERR(priv->clk_topcrm)) {
> + ret = PTR_ERR(priv->clk_topcrm);
> + dev_err(&pdev->dev, "failed to get topcrm clock: %d\n", ret);
> + return ret;
> + }
> +
> + ret = clk_prepare_enable(priv->clk_topcrm);
> + if (ret) {
> + dev_err(&pdev->dev, "failed to enable topcrm clock: %d\n",
> + ret);
> + return ret;
> + }
> +
> + priv->clk_apb = devm_clk_get(&pdev->dev, "apb");
> + if (IS_ERR(priv->clk_apb)) {
> + ret = PTR_ERR(priv->clk_apb);
> + dev_err(&pdev->dev, "failed to get apb clock: %d\n", ret);
> + goto disable_clk_topcrm;
> + }
> +
> + ret = clk_prepare_enable(priv->clk_apb);
> + if (ret) {
> + dev_err(&pdev->dev, "failed to enable apb clock: %d\n",
> + ret);
> + goto disable_clk_topcrm;
> + }
> +
> + mutex_init(&priv->lock);
> + priv->tzd = thermal_zone_of_sensor_register(&pdev->dev,
> + 0, priv, &zx2967_of_thermal_ops);
> +
> + if (IS_ERR(priv->tzd)) {
> + ret = PTR_ERR(priv->tzd);
> + dev_err(&pdev->dev, "failed to register sensor: %d\n", ret);
> + goto disable_clk_all;
> + }
> +
> + if (priv->tzd->tzp->slope == 0) {
> + thermal_zone_of_sensor_unregister(&pdev->dev, priv->tzd);
> + dev_err(&pdev->dev, "coefficients of sensor is invalid\n");
> + ret = -EINVAL;
> + goto disable_clk_all;
> + }
> +
> + priv->dev = &pdev->dev;
> + platform_set_drvdata(pdev, priv);
> +
> + return 0;
> +
> +disable_clk_all:
> + clk_disable_unprepare(priv->clk_apb);
> +disable_clk_topcrm:
> + clk_disable_unprepare(priv->clk_topcrm);
> + return ret;
> +}
> +
> +static int zx2967_thermal_exit(struct platform_device *pdev)
> +{
> + struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
> +
> + thermal_zone_of_sensor_unregister(&pdev->dev, priv->tzd);
> + clk_disable_unprepare(priv->clk_topcrm);
> + clk_disable_unprepare(priv->clk_apb);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id zx2967_thermal_id_table[] = {
> + { .compatible = "zte,zx296718-thermal" },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, zx2967_thermal_id_table);
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int zx2967_thermal_suspend(struct device *dev)
> +{
> + struct platform_device *pdev = to_platform_device(dev);
> + struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
> +
> + if (priv && priv->clk_topcrm)
> + clk_disable_unprepare(priv->clk_topcrm);
> +
> + if (priv && priv->clk_apb)
> + clk_disable_unprepare(priv->clk_apb);
> +
> + return 0;
> +}
> +
> +static int zx2967_thermal_resume(struct device *dev)
> +{
> + struct platform_device *pdev = to_platform_device(dev);
> + struct zx2967_thermal_priv *priv = platform_get_drvdata(pdev);
> + int error;
> +
> + error = clk_prepare_enable(priv->clk_topcrm);
> + if (error)
> + return error;
> +
> + error = clk_prepare_enable(priv->clk_apb);
> + if (error) {
> + clk_disable_unprepare(priv->clk_topcrm);
> + return error;
> + }
> +
> + return 0;
> +}
> +#endif
> +
> +static SIMPLE_DEV_PM_OPS(zx2967_thermal_pm_ops,
> + zx2967_thermal_suspend, zx2967_thermal_resume);
> +
> +static struct platform_driver zx2967_thermal_driver = {
> + .probe = zx2967_thermal_probe,
> + .remove = zx2967_thermal_exit,
> + .driver = {
> + .name = "zx2967_thermal",
> + .of_match_table = zx2967_thermal_id_table,
> + .pm = &zx2967_thermal_pm_ops,
> + },
> +};
> +module_platform_driver(zx2967_thermal_driver);
> +
> +MODULE_AUTHOR("Baoyou Xie <baoyou.xie@linaro.org>");
> +MODULE_DESCRIPTION("ZTE zx2967 thermal driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 10+ messages in thread