[U-Boot] [PATCH v2 00/12] Add Marvell ESPRESSOBin community board support

[U-Boot] [PATCH v2 00/12] Add Marvell ESPRESSOBin community board support

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

This patch set adds support for Marvell ESPRESSOBin community board.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter project site.
It has (current board version 3.1.1):
- Dual core Cortex-A53 @1.2GHz CPU (Marvell Armada-3720)
- 512MB/1GB/2GB DDR3 RAM (depends on selected configuration)
- Mini-PCIe 2.0 slot
- Single SATA-3 port with Molex SATA power connector
- USB 2.0 port 
- USB 3.0 port
- Gigabit Ethernet switch with 3 ports
- Micro-SD socket
- Soldering pads for (unpopulated) eMMC chip
- Two 46-pin GPIO connectors.
- SPI boot flash
- Boot source selection jumpers (SPI/SATA/UART/Auto)
- Micro JTAG connector (10 pin)
- Micro USB serial port 

Changes for v2:
- The patch set has grew by 2 patches:
  - Changed naming of common A37xx files from board-specific
    to platform (mvebu_db-88f3720 =>> mvebu_armada-37xx)
  - Removed CONFIG_DM_I2C_COMPAT from board configuration
    files as advised by compilation warning
- Rebase all related files on top of newly named platform and
  on top of "Prepare v2017.03-rc2" commit
- Beatify the Topaz initialization code by using register names
  instead of numeric address values
- Added missing include in board support code

Konstantin Porotchkin (12):
  arm64: mvebu: Rename the db-88f3720 to armada-37xx platform
  arm64: a37xx: Enable Marvell ETH PHY support
  arm64: a37xx: Enable bubt command support on A3720-DB
  arm64: a37xx: dts: Add pin control nodes to DT
  arm64: a37xx: Handle pin controls in early board init
  mvebu: neta: Add support for board init function
  mvebu: neta: a37xx: Add fixed link support to neta driver
  mvebu: a37xx: Add init for ESPRESSBin Topaz switch
  arm64: dts: Add device tree for ESPRESSOBin board
  arm64: mvebu: Add default config for ESPRESSOBin board
  arm64: a37xx: Disable DB configurations on ESPRESSOBin board
  arm64: a37xx: Remove DM_I2C_COMPAT from the board config

 arch/arm/dts/Makefile                       |   1 +
 arch/arm/dts/armada-3720-espressobin.dts    | 135 +++++++++++++++
 arch/arm/dts/armada-37xx.dtsi               |  14 ++
 arch/arm/mach-mvebu/Kconfig                 |  10 +-
 board/Marvell/mvebu_armada-37xx/MAINTAINERS |   6 +
 board/Marvell/mvebu_armada-37xx/Makefile    |   7 +
 board/Marvell/mvebu_armada-37xx/board.c     | 258 ++++++++++++++++++++++++++++
 board/Marvell/mvebu_db-88f3720/MAINTAINERS  |   6 -
 board/Marvell/mvebu_db-88f3720/Makefile     |   7 -
 board/Marvell/mvebu_db-88f3720/board.c      | 134 ---------------
 configs/mvebu_db-88f3720_defconfig          |   6 +-
 configs/mvebu_espressobin-88f3720_defconfig |  66 +++++++
 drivers/net/mvneta.c                        | 125 +++++++++++---
 include/configs/mvebu_armada-37xx.h         | 131 ++++++++++++++
 include/configs/mvebu_db-88f3720.h          | 130 --------------
 15 files changed, 724 insertions(+), 312 deletions(-)
 create mode 100644 arch/arm/dts/armada-3720-espressobin.dts
 create mode 100644 board/Marvell/mvebu_armada-37xx/MAINTAINERS
 create mode 100644 board/Marvell/mvebu_armada-37xx/Makefile
 create mode 100644 board/Marvell/mvebu_armada-37xx/board.c
 delete mode 100644 board/Marvell/mvebu_db-88f3720/MAINTAINERS
 delete mode 100644 board/Marvell/mvebu_db-88f3720/Makefile
 delete mode 100644 board/Marvell/mvebu_db-88f3720/board.c
 create mode 100644 configs/mvebu_espressobin-88f3720_defconfig
 create mode 100644 include/configs/mvebu_armada-37xx.h
 delete mode 100644 include/configs/mvebu_db-88f3720.h

-- 
2.7.4

[U-Boot] [PATCH v2 01/12] arm64: mvebu: Rename the db-88f3720 to armada-37xx platform

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
Changes for v2:
- This patch was missing in the v1

 arch/arm/mach-mvebu/Kconfig                 |  10 +--
 board/Marvell/mvebu_armada-37xx/MAINTAINERS |   6 ++
 board/Marvell/mvebu_armada-37xx/Makefile    |   7 ++
 board/Marvell/mvebu_armada-37xx/board.c     | 134 ++++++++++++++++++++++++++++
 board/Marvell/mvebu_db-88f3720/MAINTAINERS  |   6 --
 board/Marvell/mvebu_db-88f3720/Makefile     |   7 --
 board/Marvell/mvebu_db-88f3720/board.c      | 134 ----------------------------
 configs/mvebu_db-88f3720_defconfig          |   2 +-
 include/configs/mvebu_armada-37xx.h         | 130 +++++++++++++++++++++++++++
 include/configs/mvebu_db-88f3720.h          | 130 ---------------------------
 10 files changed, 283 insertions(+), 283 deletions(-)
 create mode 100644 board/Marvell/mvebu_armada-37xx/MAINTAINERS
 create mode 100644 board/Marvell/mvebu_armada-37xx/Makefile
 create mode 100644 board/Marvell/mvebu_armada-37xx/board.c
 delete mode 100644 board/Marvell/mvebu_db-88f3720/MAINTAINERS
 delete mode 100644 board/Marvell/mvebu_db-88f3720/Makefile
 delete mode 100644 board/Marvell/mvebu_db-88f3720/board.c
 create mode 100644 include/configs/mvebu_armada-37xx.h
 delete mode 100644 include/configs/mvebu_db-88f3720.h

diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index 412bda4..a256c2f 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -74,8 +74,8 @@ config TARGET_CLEARFOG
 	bool "Support ClearFog"
 	select 88F6820
 
-config TARGET_MVEBU_DB_88F3720
-	bool "Support DB-88F3720 Armada 3720"
+config TARGET_MVEBU_ARMADA_37XX
+	bool "Support Armada 37xx platforms"
 	select ARMADA_3700
 
 config TARGET_DB_88F6720
@@ -116,7 +116,7 @@ endchoice
 
 config SYS_BOARD
 	default "clearfog" if TARGET_CLEARFOG
-	default "mvebu_db-88f3720" if TARGET_MVEBU_DB_88F3720
+	default "mvebu_armada-37xx" if TARGET_MVEBU_ARMADA_37XX
 	default "db-88f6720" if TARGET_DB_88F6720
 	default "db-88f6820-gp" if TARGET_DB_88F6820_GP
 	default "db-88f6820-amc" if TARGET_DB_88F6820_AMC
@@ -128,7 +128,7 @@ config SYS_BOARD
 
 config SYS_CONFIG_NAME
 	default "clearfog" if TARGET_CLEARFOG
-	default "mvebu_db-88f3720" if TARGET_MVEBU_DB_88F3720
+	default "mvebu_armada-37xx" if TARGET_MVEBU_ARMADA_37XX
 	default "db-88f6720" if TARGET_DB_88F6720
 	default "db-88f6820-gp" if TARGET_DB_88F6820_GP
 	default "db-88f6820-amc" if TARGET_DB_88F6820_AMC
@@ -140,7 +140,7 @@ config SYS_CONFIG_NAME
 
 config SYS_VENDOR
 	default "Marvell" if TARGET_DB_MV784MP_GP
-	default "Marvell" if TARGET_MVEBU_DB_88F3720
+	default "Marvell" if TARGET_MVEBU_ARMADA_37XX
 	default "Marvell" if TARGET_DB_88F6720
 	default "Marvell" if TARGET_DB_88F6820_GP
 	default "Marvell" if TARGET_DB_88F6820_AMC
diff --git a/board/Marvell/mvebu_armada-37xx/MAINTAINERS b/board/Marvell/mvebu_armada-37xx/MAINTAINERS
new file mode 100644
index 0000000..52a3869
--- /dev/null
+++ b/board/Marvell/mvebu_armada-37xx/MAINTAINERS
@@ -0,0 +1,6 @@
+MVEBU_DB_88F3720 BOARD
+M:	Stefan Roese <sr@denx.de>
+S:	Maintained
+F:	board/Marvell/mvebu_armada-37xx/
+F:	include/configs/mvebu_armada-37xx.h
+F:	configs/mvebu_db-88f3720_defconfig
diff --git a/board/Marvell/mvebu_armada-37xx/Makefile b/board/Marvell/mvebu_armada-37xx/Makefile
new file mode 100644
index 0000000..ed39738
--- /dev/null
+++ b/board/Marvell/mvebu_armada-37xx/Makefile
@@ -0,0 +1,7 @@
+#
+# Copyright (C) 2016 Stefan Roese <sr@denx.de>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= board.o
diff --git a/board/Marvell/mvebu_armada-37xx/board.c b/board/Marvell/mvebu_armada-37xx/board.c
new file mode 100644
index 0000000..edf88c7
--- /dev/null
+++ b/board/Marvell/mvebu_armada-37xx/board.c
@@ -0,0 +1,134 @@
+/*
+ * Copyright (C) 2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* IO expander I2C device */
+#define I2C_IO_EXP_ADDR		0x22
+#define I2C_IO_CFG_REG_0	0x6
+#define I2C_IO_DATA_OUT_REG_0	0x2
+#define I2C_IO_REG_0_SATA_OFF	2
+#define I2C_IO_REG_0_USB_H_OFF	1
+
+int board_early_init_f(void)
+{
+	/* Nothing to do (yet), perhaps later some pin-muxing etc */
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+	return 0;
+}
+
+/* Board specific AHCI / SATA enable code */
+int board_ahci_enable(void)
+{
+	struct udevice *dev;
+	int ret;
+	u8 buf[8];
+
+	/* Configure IO exander PCA9555: 7bit address 0x22 */
+	ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
+	if (ret) {
+		printf("Cannot find PCA9555: %d\n", ret);
+		return 0;
+	}
+
+	ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
+	if (ret) {
+		printf("Failed to read IO expander value via I2C\n");
+		return -EIO;
+	}
+
+	/*
+	 * Enable SATA power via IO expander connected via I2C by setting
+	 * the corresponding bit to output mode to enable power for SATA
+	 */
+	buf[0] &= ~(1 << I2C_IO_REG_0_SATA_OFF);
+	ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
+	if (ret) {
+		printf("Failed to set IO expander via I2C\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
+/* Board specific xHCI enable code */
+int board_xhci_enable(void)
+{
+	struct udevice *dev;
+	int ret;
+	u8 buf[8];
+
+	/* Configure IO exander PCA9555: 7bit address 0x22 */
+	ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
+	if (ret) {
+		printf("Cannot find PCA9555: %d\n", ret);
+		return 0;
+	}
+
+	printf("Enable USB VBUS\n");
+
+	/*
+	 * Read configuration (direction) and set VBUS pin as output
+	 * (reset pin = output)
+	 */
+	ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
+	if (ret) {
+		printf("Failed to read IO expander value via I2C\n");
+		return -EIO;
+	}
+	buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF);
+	ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
+	if (ret) {
+		printf("Failed to set IO expander via I2C\n");
+		return -EIO;
+	}
+
+	/* Read VBUS output value and disable it */
+	ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
+	if (ret) {
+		printf("Failed to read IO expander value via I2C\n");
+		return -EIO;
+	}
+	buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF);
+	ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
+	if (ret) {
+		printf("Failed to set IO expander via I2C\n");
+		return -EIO;
+	}
+
+	/*
+	 * Required delay for configuration to settle - must wait for
+	 * power on port is disabled in case VBUS signal was high,
+	 * required 3 seconds delay to let VBUS signal fully settle down
+	 */
+	mdelay(3000);
+
+	/* Enable VBUS power: Set output value of VBUS pin as enabled */
+	buf[0] |= (1 << I2C_IO_REG_0_USB_H_OFF);
+	ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
+	if (ret) {
+		printf("Failed to set IO expander via I2C\n");
+		return -EIO;
+	}
+
+	mdelay(500); /* required delay to let output value settle */
+
+	return 0;
+}
diff --git a/board/Marvell/mvebu_db-88f3720/MAINTAINERS b/board/Marvell/mvebu_db-88f3720/MAINTAINERS
deleted file mode 100644
index 4e80917..0000000
--- a/board/Marvell/mvebu_db-88f3720/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-MVEBU_DB_88F3720 BOARD
-M:	Stefan Roese <sr@denx.de>
-S:	Maintained
-F:	board/Marvell/mvebu_db-88f3720/
-F:	include/configs/mvebu_db-88f3720.h
-F:	configs/mvebu_db-88f3720_defconfig
diff --git a/board/Marvell/mvebu_db-88f3720/Makefile b/board/Marvell/mvebu_db-88f3720/Makefile
deleted file mode 100644
index ed39738..0000000
--- a/board/Marvell/mvebu_db-88f3720/Makefile
+++ /dev/null
@@ -1,7 +0,0 @@
-#
-# Copyright (C) 2016 Stefan Roese <sr@denx.de>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= board.o
diff --git a/board/Marvell/mvebu_db-88f3720/board.c b/board/Marvell/mvebu_db-88f3720/board.c
deleted file mode 100644
index edf88c7..0000000
--- a/board/Marvell/mvebu_db-88f3720/board.c
+++ /dev/null
@@ -1,134 +0,0 @@
-/*
- * Copyright (C) 2016 Stefan Roese <sr@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <asm/io.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* IO expander I2C device */
-#define I2C_IO_EXP_ADDR		0x22
-#define I2C_IO_CFG_REG_0	0x6
-#define I2C_IO_DATA_OUT_REG_0	0x2
-#define I2C_IO_REG_0_SATA_OFF	2
-#define I2C_IO_REG_0_USB_H_OFF	1
-
-int board_early_init_f(void)
-{
-	/* Nothing to do (yet), perhaps later some pin-muxing etc */
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-
-	return 0;
-}
-
-/* Board specific AHCI / SATA enable code */
-int board_ahci_enable(void)
-{
-	struct udevice *dev;
-	int ret;
-	u8 buf[8];
-
-	/* Configure IO exander PCA9555: 7bit address 0x22 */
-	ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
-	if (ret) {
-		printf("Cannot find PCA9555: %d\n", ret);
-		return 0;
-	}
-
-	ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
-	if (ret) {
-		printf("Failed to read IO expander value via I2C\n");
-		return -EIO;
-	}
-
-	/*
-	 * Enable SATA power via IO expander connected via I2C by setting
-	 * the corresponding bit to output mode to enable power for SATA
-	 */
-	buf[0] &= ~(1 << I2C_IO_REG_0_SATA_OFF);
-	ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
-	if (ret) {
-		printf("Failed to set IO expander via I2C\n");
-		return -EIO;
-	}
-
-	return 0;
-}
-
-/* Board specific xHCI enable code */
-int board_xhci_enable(void)
-{
-	struct udevice *dev;
-	int ret;
-	u8 buf[8];
-
-	/* Configure IO exander PCA9555: 7bit address 0x22 */
-	ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
-	if (ret) {
-		printf("Cannot find PCA9555: %d\n", ret);
-		return 0;
-	}
-
-	printf("Enable USB VBUS\n");
-
-	/*
-	 * Read configuration (direction) and set VBUS pin as output
-	 * (reset pin = output)
-	 */
-	ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
-	if (ret) {
-		printf("Failed to read IO expander value via I2C\n");
-		return -EIO;
-	}
-	buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF);
-	ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
-	if (ret) {
-		printf("Failed to set IO expander via I2C\n");
-		return -EIO;
-	}
-
-	/* Read VBUS output value and disable it */
-	ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
-	if (ret) {
-		printf("Failed to read IO expander value via I2C\n");
-		return -EIO;
-	}
-	buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF);
-	ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
-	if (ret) {
-		printf("Failed to set IO expander via I2C\n");
-		return -EIO;
-	}
-
-	/*
-	 * Required delay for configuration to settle - must wait for
-	 * power on port is disabled in case VBUS signal was high,
-	 * required 3 seconds delay to let VBUS signal fully settle down
-	 */
-	mdelay(3000);
-
-	/* Enable VBUS power: Set output value of VBUS pin as enabled */
-	buf[0] |= (1 << I2C_IO_REG_0_USB_H_OFF);
-	ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
-	if (ret) {
-		printf("Failed to set IO expander via I2C\n");
-		return -EIO;
-	}
-
-	mdelay(500); /* required delay to let output value settle */
-
-	return 0;
-}
diff --git a/configs/mvebu_db-88f3720_defconfig b/configs/mvebu_db-88f3720_defconfig
index 80f2599..4286695 100644
--- a/configs/mvebu_db-88f3720_defconfig
+++ b/configs/mvebu_db-88f3720_defconfig
@@ -1,7 +1,7 @@
 CONFIG_ARM=y
 CONFIG_ARCH_MVEBU=y
 CONFIG_SYS_MALLOC_F_LEN=0x2000
-CONFIG_TARGET_MVEBU_DB_88F3720=y
+CONFIG_TARGET_MVEBU_ARMADA_37XX=y
 CONFIG_DEFAULT_DEVICE_TREE="armada-3720-db"
 CONFIG_AHCI=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
diff --git a/include/configs/mvebu_armada-37xx.h b/include/configs/mvebu_armada-37xx.h
new file mode 100644
index 0000000..f5adfef
--- /dev/null
+++ b/include/configs/mvebu_armada-37xx.h
@@ -0,0 +1,130 @@
+/*
+ * Copyright (C) 2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _CONFIG_MVEBU_ARMADA_37XX_H
+#define _CONFIG_MVEBU_ARMADA_37XX_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+#define	CONFIG_SYS_TEXT_BASE	0x00000000
+
+/* additions for new ARM relocation support */
+#define CONFIG_SYS_SDRAM_BASE	0x00000000
+
+#define CONFIG_NR_DRAM_BANKS	1
+
+/* auto boot */
+#define CONFIG_PREBOOT
+
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, \
+					  115200, 230400, 460800, 921600 }
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs  */
+#define CONFIG_INITRD_TAG		/* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS	/* enable memory tag */
+
+#define	CONFIG_SYS_CBSIZE	1024	/* Console I/O Buff Size */
+#define	CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE \
+		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN	(4 << 20) /* 4MiB for malloc() */
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_ARCH_CPU_INIT		/* call arch_cpu_init() */
+#define CONFIG_SYS_LOAD_ADDR	0x00800000	/* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00800000	/* 8M */
+#define CONFIG_SYS_MEMTEST_END	0x00ffffff	/*(_16M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS	32	/* max number of command args */
+
+#define CONFIG_SYS_ALT_MEMTEST
+
+/* End of 16M scrubbed by training in bootrom */
+#define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_TEXT_BASE + 0xFF0000)
+
+/*
+ * I2C
+ */
+#define CONFIG_I2C_MV
+#define CONFIG_SYS_I2C_SLAVE		0x0
+
+/*
+ * SPI Flash configuration
+ */
+#define CONFIG_ENV_SPI_BUS		0
+#define CONFIG_ENV_SPI_CS		0
+
+/* SPI NOR flash default params, used by sf commands */
+#define CONFIG_SF_DEFAULT_SPEED		1000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
+
+/* Environment in SPI NOR flash */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET		0x180000 /* as Marvell U-Boot version */
+#define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
+#define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */
+
+/*
+ * Ethernet Driver configuration
+ */
+#define CONFIG_MVNETA		/* Enable Marvell Gbe Controller Driver */
+#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
+#define CONFIG_PHY_GIGE		/* GbE speed/duplex detect */
+#define CONFIG_ARP_TIMEOUT	200
+#define CONFIG_NET_RETRY_COUNT	50
+
+/* USB 2.0 */
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
+
+/* USB 3.0 */
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 3
+
+#define CONFIG_USB_MAX_CONTROLLER_COUNT (CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS + \
+					 CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS)
+
+/* USB ethernet */
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_MCS7830
+#define CONFIG_USB_ETHER_RTL8152
+#define CONFIG_USB_ETHER_SMSC95XX
+
+/*
+ * SATA/SCSI/AHCI configuration
+ */
+#define CONFIG_SCSI
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+#define CONFIG_SYS_64BIT_LBA
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID	2
+#define CONFIG_SYS_SCSI_MAX_LUN		1
+#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+					 CONFIG_SYS_SCSI_MAX_LUN)
+
+#define CONFIG_SUPPORT_VFAT
+
+#endif /* _CONFIG_MVEBU_ARMADA_37XX_H */
diff --git a/include/configs/mvebu_db-88f3720.h b/include/configs/mvebu_db-88f3720.h
deleted file mode 100644
index 753ed1e..0000000
--- a/include/configs/mvebu_db-88f3720.h
+++ /dev/null
@@ -1,130 +0,0 @@
-/*
- * Copyright (C) 2016 Stefan Roese <sr@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _CONFIG_MVEBU_DB_88F3720_H
-#define _CONFIG_MVEBU_DB_88F3720_H
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_DISPLAY_BOARDINFO_LATE
-
-#define	CONFIG_SYS_TEXT_BASE	0x00000000
-
-/* additions for new ARM relocation support */
-#define CONFIG_SYS_SDRAM_BASE	0x00000000
-
-#define CONFIG_NR_DRAM_BANKS	1
-
-/* auto boot */
-#define CONFIG_PREBOOT
-
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, \
-					  115200, 230400, 460800, 921600 }
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs  */
-#define CONFIG_INITRD_TAG		/* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS	/* enable memory tag */
-
-#define	CONFIG_SYS_CBSIZE	1024	/* Console I/O Buff Size */
-#define	CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE \
-		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN	(4 << 20) /* 4MiB for malloc() */
-
-/*
- * Other required minimal configurations
- */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_ARCH_CPU_INIT		/* call arch_cpu_init() */
-#define CONFIG_SYS_LOAD_ADDR	0x00800000	/* default load adr- 8M */
-#define CONFIG_SYS_MEMTEST_START 0x00800000	/* 8M */
-#define CONFIG_SYS_MEMTEST_END	0x00ffffff	/*(_16M -1) */
-#define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
-#define CONFIG_SYS_MAXARGS	32	/* max number of command args */
-
-#define CONFIG_SYS_ALT_MEMTEST
-
-/* End of 16M scrubbed by training in bootrom */
-#define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_TEXT_BASE + 0xFF0000)
-
-/*
- * I2C
- */
-#define CONFIG_I2C_MV
-#define CONFIG_SYS_I2C_SLAVE		0x0
-
-/*
- * SPI Flash configuration
- */
-#define CONFIG_ENV_SPI_BUS		0
-#define CONFIG_ENV_SPI_CS		0
-
-/* SPI NOR flash default params, used by sf commands */
-#define CONFIG_SF_DEFAULT_SPEED		1000000
-#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
-#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
-
-/* Environment in SPI NOR flash */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_OFFSET		0x180000 /* as Marvell U-Boot version */
-#define CONFIG_ENV_SIZE			(64 << 10) /* 64KiB */
-#define CONFIG_ENV_SECT_SIZE		(64 << 10) /* 64KiB sectors */
-
-/*
- * Ethernet Driver configuration
- */
-#define CONFIG_MVNETA		/* Enable Marvell Gbe Controller Driver */
-#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
-#define CONFIG_PHY_GIGE		/* GbE speed/duplex detect */
-#define CONFIG_ARP_TIMEOUT	200
-#define CONFIG_NET_RETRY_COUNT	50
-
-/* USB 2.0 */
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
-
-/* USB 3.0 */
-#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 3
-
-#define CONFIG_USB_MAX_CONTROLLER_COUNT (CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS + \
-					 CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS)
-
-/* USB ethernet */
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
-#define CONFIG_USB_ETHER_MCS7830
-#define CONFIG_USB_ETHER_RTL8152
-#define CONFIG_USB_ETHER_SMSC95XX
-
-/*
- * SATA/SCSI/AHCI configuration
- */
-#define CONFIG_SCSI
-#define CONFIG_SCSI_AHCI
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_LIBATA
-#define CONFIG_LBA48
-#define CONFIG_SYS_64BIT_LBA
-
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID	2
-#define CONFIG_SYS_SCSI_MAX_LUN		1
-#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
-					 CONFIG_SYS_SCSI_MAX_LUN)
-
-#define CONFIG_SUPPORT_VFAT
-
-#endif /* _CONFIG_MVEBU_DB_88F3720_H */
-- 
2.7.4

[U-Boot] [PATCH v2 02/12] arm64: a37xx: Enable Marvell ETH PHY support

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Enable support for Marvell Ethernet PHYs on A37xx platforms

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
Changes for v2:
- No changes, rebased on top of new platform file

 include/configs/mvebu_armada-37xx.h | 1 +
 1 file changed, 1 insertion(+)

diff --git a/include/configs/mvebu_armada-37xx.h b/include/configs/mvebu_armada-37xx.h
index f5adfef..fd2ae8e 100644
--- a/include/configs/mvebu_armada-37xx.h
+++ b/include/configs/mvebu_armada-37xx.h
@@ -93,6 +93,7 @@
 #define CONFIG_PHY_GIGE		/* GbE speed/duplex detect */
 #define CONFIG_ARP_TIMEOUT	200
 #define CONFIG_NET_RETRY_COUNT	50
+#define CONFIG_PHY_MARVELL
 
 /* USB 2.0 */
 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
-- 
2.7.4

[U-Boot] [PATCH v2 03/12] arm64: a37xx: Enable bubt command support on A3720-DB

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Enable mvebu bubt command support on A3720 DB

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
Changes for v2:
- No changes

 configs/mvebu_db-88f3720_defconfig | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/configs/mvebu_db-88f3720_defconfig b/configs/mvebu_db-88f3720_defconfig
index 4286695..bdb96e9 100644
--- a/configs/mvebu_db-88f3720_defconfig
+++ b/configs/mvebu_db-88f3720_defconfig
@@ -33,6 +33,9 @@ CONFIG_CMD_FS_GENERIC=y
 CONFIG_MAC_PARTITION=y
 CONFIG_ISO_PARTITION=y
 CONFIG_EFI_PARTITION=y
+CONFIG_CMD_MVEBU_BUBT=y
+CONFIG_SHA1=y
+CONFIG_SHA256=y
 CONFIG_BLOCK_CACHE=y
 CONFIG_DM_I2C=y
 CONFIG_DM_I2C_COMPAT=y
-- 
2.7.4

[U-Boot] [PATCH v2 04/12] arm64: a37xx: dts: Add pin control nodes to DT

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Add pin control nodes for North and South bridges to
Armada-37xx DT

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
 arch/arm/dts/armada-37xx.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
Changes for v2:
- No changes, rebased on top of new platform files

diff --git a/arch/arm/dts/armada-37xx.dtsi b/arch/arm/dts/armada-37xx.dtsi
index 062f2a6..5bea63b 100644
--- a/arch/arm/dts/armada-37xx.dtsi
+++ b/arch/arm/dts/armada-37xx.dtsi
@@ -193,6 +193,20 @@
 				status = "disabled";
 			};
 
+			pinctl0: pinctl at 13830 { /* north bridge */
+				compatible = "marvell,armada-3700-pinctl";
+				bank-name = "armada-3700-nb";
+				reg = <0x13830 0x4>;
+				pin-count = <36>;
+			};
+
+			pinctl1: pinctl at 18830 { /* south bridge */
+				compatible = "marvell,armada-3700-pinctl";
+				bank-name = "armada-3700-sb";
+				reg = <0x18830 0x4>;
+				pin-count = <30>;
+			};
+
 			comphy: comphy at 18300 {
 				compatible = "marvell,mvebu-comphy", "marvell,comphy-armada-3700";
 				reg = <0x18300 0x28>,
-- 
2.7.4

[U-Boot] [PATCH v2 05/12] arm64: a37xx: Handle pin controls in early board init

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Fix the default pin control values in a board-specific
function on early board init stage.
This fix allows the NETA driver to work in RGMII
mode until the full-featured pin control driver gets
introduced.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
Changes for v2:
- No changes, rebased on top of new platform files

 board/Marvell/mvebu_armada-37xx/board.c | 26 +++++++++++++++++++++++++-
 1 file changed, 25 insertions(+), 1 deletion(-)

diff --git a/board/Marvell/mvebu_armada-37xx/board.c b/board/Marvell/mvebu_armada-37xx/board.c
index edf88c7..3337f3f 100644
--- a/board/Marvell/mvebu_armada-37xx/board.c
+++ b/board/Marvell/mvebu_armada-37xx/board.c
@@ -19,9 +19,33 @@ DECLARE_GLOBAL_DATA_PTR;
 #define I2C_IO_REG_0_SATA_OFF	2
 #define I2C_IO_REG_0_USB_H_OFF	1
 
+#define PINCTRL_NB_REG_VALUE	0x000173fa
+#define PINCTRL_SB_REG_VALUE	0x00007a23
+
 int board_early_init_f(void)
 {
-	/* Nothing to do (yet), perhaps later some pin-muxing etc */
+	const void *blob = gd->fdt_blob;
+	const char *bank_name;
+	const char *compat = "marvell,armada-3700-pinctl";
+	int off, len;
+	void __iomem *addr;
+
+	/* FIXME
+	 * Temporary WA for setting correct pin control values
+	 * until the real pin control driver is awailable.
+	 */
+	off = fdt_node_offset_by_compatible(blob, -1, compat);
+	while (off != -FDT_ERR_NOTFOUND) {
+		bank_name = fdt_getprop(blob, off, "bank-name", &len);
+		addr = (void __iomem *)fdtdec_get_addr_size_auto_noparent(
+				blob, off, "reg", 0, NULL, true);
+		if (!strncmp(bank_name, "armada-3700-nb", len))
+			writel(PINCTRL_NB_REG_VALUE, addr);
+		else if (!strncmp(bank_name, "armada-3700-sb", len))
+			writel(PINCTRL_SB_REG_VALUE, addr);
+
+		off = fdt_node_offset_by_compatible(blob, off, compat);
+	}
 
 	return 0;
 }
-- 
2.7.4

[U-Boot] [PATCH v2 06/12] mvebu: neta: Add support for board init function

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
Changes for v2:
- No changes

 drivers/net/mvneta.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/net/mvneta.c b/drivers/net/mvneta.c
index 674075f..a1e2136 100644
--- a/drivers/net/mvneta.c
+++ b/drivers/net/mvneta.c
@@ -404,6 +404,15 @@ static struct buffer_location buffer_loc;
  */
 #define BD_SPACE	(1 << 20)
 
+/*
+ * Dummy implementation that can be overwritten by a board
+ * specific function
+ */
+__weak int board_network_enable(struct mii_dev *bus)
+{
+	return 0;
+}
+
 /* Utility/helper methods */
 
 /* Write helper method */
@@ -1615,6 +1624,7 @@ static int mvneta_probe(struct udevice *dev)
 	struct mii_dev *bus;
 	unsigned long addr;
 	void *bd_space;
+	int ret;
 
 	/*
 	 * Allocate buffer area for descs and rx_buffers. This is only
@@ -1664,7 +1674,11 @@ static int mvneta_probe(struct udevice *dev)
 	bus->priv = (void *)pp;
 	pp->bus = bus;
 
-	return mdio_register(bus);
+	ret = mdio_register(bus);
+	if (ret)
+		return ret;
+
+	return board_network_enable(bus);
 }
 
 static void mvneta_stop(struct udevice *dev)
-- 
2.7.4

[U-Boot] [PATCH v2 07/12] mvebu: neta: a37xx: Add fixed link support to neta driver

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
Changes for v2:
- No changes

 drivers/net/mvneta.c | 109 ++++++++++++++++++++++++++++++++++++++-------------
 1 file changed, 82 insertions(+), 27 deletions(-)

diff --git a/drivers/net/mvneta.c b/drivers/net/mvneta.c
index a1e2136..8881cc7 100644
--- a/drivers/net/mvneta.c
+++ b/drivers/net/mvneta.c
@@ -191,11 +191,16 @@ DECLARE_GLOBAL_DATA_PTR;
 #define MVNETA_GMAC_AUTONEG_CONFIG               0x2c0c
 #define      MVNETA_GMAC_FORCE_LINK_DOWN         BIT(0)
 #define      MVNETA_GMAC_FORCE_LINK_PASS         BIT(1)
+#define      MVNETA_GMAC_FORCE_LINK_UP           (BIT(0) | BIT(1))
+#define      MVNETA_GMAC_IB_BYPASS_AN_EN         BIT(3)
 #define      MVNETA_GMAC_CONFIG_MII_SPEED        BIT(5)
 #define      MVNETA_GMAC_CONFIG_GMII_SPEED       BIT(6)
 #define      MVNETA_GMAC_AN_SPEED_EN             BIT(7)
+#define      MVNETA_GMAC_SET_FC_EN               BIT(8)
+#define      MVNETA_GMAC_ADVERT_FC_EN            BIT(9)
 #define      MVNETA_GMAC_CONFIG_FULL_DUPLEX      BIT(12)
 #define      MVNETA_GMAC_AN_DUPLEX_EN            BIT(13)
+#define      MVNETA_GMAC_SAMPLE_TX_CFG_EN        BIT(15)
 #define MVNETA_MIB_COUNTERS_BASE                 0x3080
 #define      MVNETA_MIB_LATE_COLLISION           0x7c
 #define MVNETA_DA_FILT_SPEC_MCAST                0x3400
@@ -566,6 +571,13 @@ static void mvneta_rxq_buf_size_set(struct mvneta_port *pp,
 	mvreg_write(pp, MVNETA_RXQ_SIZE_REG(rxq->id), val);
 }
 
+static int mvneta_port_is_fixed_link(struct mvneta_port *pp)
+{
+	/* phy_addr is set to invalid value for fixed link */
+	return pp->phyaddr > PHY_MAX_ADDR;
+}
+
+
 /* Start the Ethernet port RX and TX activity */
 static void mvneta_port_up(struct mvneta_port *pp)
 {
@@ -816,10 +828,12 @@ static void mvneta_defaults_set(struct mvneta_port *pp)
 	/* Assign port SDMA configuration */
 	mvreg_write(pp, MVNETA_SDMA_CONFIG, val);
 
-	/* Enable PHY polling in hardware for U-Boot */
-	val = mvreg_read(pp, MVNETA_UNIT_CONTROL);
-	val |= MVNETA_PHY_POLLING_ENABLE;
-	mvreg_write(pp, MVNETA_UNIT_CONTROL, val);
+	/* Enable PHY polling in hardware if not in fixed-link mode */
+	if (!mvneta_port_is_fixed_link(pp)) {
+		val = mvreg_read(pp, MVNETA_UNIT_CONTROL);
+		val |= MVNETA_PHY_POLLING_ENABLE;
+		mvreg_write(pp, MVNETA_UNIT_CONTROL, val);
+	}
 
 	mvneta_set_ucast_table(pp, -1);
 	mvneta_set_special_mcast_table(pp, -1);
@@ -1137,6 +1151,11 @@ static void mvneta_adjust_link(struct udevice *dev)
 	struct phy_device *phydev = pp->phydev;
 	int status_change = 0;
 
+	if (mvneta_port_is_fixed_link(pp)) {
+		debug("Using fixed link, skip link adjust\n");
+		return;
+	}
+
 	if (phydev->link) {
 		if ((pp->speed != phydev->speed) ||
 		    (pp->duplex != phydev->duplex)) {
@@ -1507,28 +1526,54 @@ static int mvneta_start(struct udevice *dev)
 	mvneta_port_power_up(pp, pp->phy_interface);
 
 	if (!pp->init || pp->link == 0) {
-		/* Set phy address of the port */
-		mvreg_write(pp, MVNETA_PHY_ADDR, pp->phyaddr);
-		phydev = phy_connect(pp->bus, pp->phyaddr, dev,
-				     pp->phy_interface);
-
-		pp->phydev = phydev;
-		phy_config(phydev);
-		phy_startup(phydev);
-		if (!phydev->link) {
-			printf("%s: No link.\n", phydev->dev->name);
-			return -1;
-		}
+		if (mvneta_port_is_fixed_link(pp)) {
+			u32 val;
 
-		/* Full init on first call */
-		mvneta_init(dev);
-		pp->init = 1;
-	} else {
-		/* Upon all following calls, this is enough */
-		mvneta_port_up(pp);
-		mvneta_port_enable(pp);
+			pp->init = 1;
+			pp->link = 1;
+			mvneta_init(dev);
+
+			val = MVNETA_GMAC_FORCE_LINK_UP |
+			      MVNETA_GMAC_IB_BYPASS_AN_EN |
+			      MVNETA_GMAC_SET_FC_EN |
+			      MVNETA_GMAC_ADVERT_FC_EN |
+			      MVNETA_GMAC_SAMPLE_TX_CFG_EN;
+
+			if (pp->duplex)
+				val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
+
+			if (pp->speed == SPEED_1000)
+				val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
+			else if (pp->speed == SPEED_100)
+				val |= MVNETA_GMAC_CONFIG_MII_SPEED;
+
+			mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+		} else {
+			/* Set phy address of the port */
+			mvreg_write(pp, MVNETA_PHY_ADDR, pp->phyaddr);
+
+			phydev = phy_connect(pp->bus, pp->phyaddr, dev,
+					     pp->phy_interface);
+
+			pp->phydev = phydev;
+			phy_config(phydev);
+			phy_startup(phydev);
+			if (!phydev->link) {
+				printf("%s: No link.\n", phydev->dev->name);
+				return -1;
+			}
+
+			/* Full init on first call */
+			mvneta_init(dev);
+			pp->init = 1;
+			return 0;
+		}
 	}
 
+	/* Upon all following calls, this is enough */
+	mvneta_port_up(pp);
+	mvneta_port_enable(pp);
+
 	return 0;
 }
 
@@ -1625,6 +1670,7 @@ static int mvneta_probe(struct udevice *dev)
 	unsigned long addr;
 	void *bd_space;
 	int ret;
+	int fl_node;
 
 	/*
 	 * Allocate buffer area for descs and rx_buffers. This is only
@@ -1657,10 +1703,19 @@ static int mvneta_probe(struct udevice *dev)
 	/* PHY interface is already decoded in mvneta_ofdata_to_platdata() */
 	pp->phy_interface = pdata->phy_interface;
 
-	/* Now read phyaddr from DT */
-	addr = fdtdec_get_int(blob, node, "phy", 0);
-	addr = fdt_node_offset_by_phandle(blob, addr);
-	pp->phyaddr = fdtdec_get_int(blob, addr, "reg", 0);
+	/* fetch 'fixed-link' property from 'neta' node */
+	fl_node = fdt_subnode_offset(blob, node, "fixed-link");
+	if (fl_node != -FDT_ERR_NOTFOUND) {
+		/* set phy_addr to invalid value for fixed link */
+		pp->phyaddr = PHY_MAX_ADDR + 1;
+		pp->duplex = fdtdec_get_bool(blob, fl_node, "full-duplex");
+		pp->speed = fdtdec_get_int(blob, fl_node, "speed", 0);
+	} else {
+		/* Now read phyaddr from DT */
+		addr = fdtdec_get_int(blob, node, "phy", 0);
+		addr = fdt_node_offset_by_phandle(blob, addr);
+		pp->phyaddr = fdtdec_get_int(blob, addr, "reg", 0);
+	}
 
 	bus = mdio_alloc();
 	if (!bus) {
-- 
2.7.4

[U-Boot] [PATCH v2 08/12] mvebu: a37xx: Add init for ESPRESSBin Topaz switch

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Implement the board-specific network init function for
ESPRESSOBin community board, setting the on-board Topaz
switch port to forward mode and allow network connection
through any of the available Etherenet ports.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
---
Changes for v2:
- Change SMI registers from numeric values to symbols for better readability
- Add missing <dm.h> include

 board/Marvell/mvebu_armada-37xx/board.c | 91 +++++++++++++++++++++++++++++++++
 1 file changed, 91 insertions(+)

diff --git a/board/Marvell/mvebu_armada-37xx/board.c b/board/Marvell/mvebu_armada-37xx/board.c
index 3337f3f..b9878bf 100644
--- a/board/Marvell/mvebu_armada-37xx/board.c
+++ b/board/Marvell/mvebu_armada-37xx/board.c
@@ -5,7 +5,9 @@
  */
 
 #include <common.h>
+#include <dm.h>
 #include <i2c.h>
+#include <phy.h>
 #include <asm/io.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/soc.h>
@@ -22,6 +24,29 @@ DECLARE_GLOBAL_DATA_PTR;
 #define PINCTRL_NB_REG_VALUE	0x000173fa
 #define PINCTRL_SB_REG_VALUE	0x00007a23
 
+/* Ethernet switch registers */
+/* SMI addresses for multi-chip mode */
+#define MVEBU_PORT_CTRL_SMI_ADDR(p)	(16 + (p))
+#define MVEBU_SW_G2_SMI_ADDR		(28)
+
+/* Multi-chip mode */
+#define MVEBU_SW_SMI_DATA_REG		(1)
+#define MVEBU_SW_SMI_CMD_REG		(0)
+ #define SW_SMI_CMD_REG_ADDR_OFF	0
+ #define SW_SMI_CMD_DEV_ADDR_OFF	5
+ #define SW_SMI_CMD_SMI_OP_OFF		10
+ #define SW_SMI_CMD_SMI_MODE_OFF	12
+ #define SW_SMI_CMD_SMI_BUSY_OFF	15
+
+/* Single-chip mode */
+/* Switch Port Registers */
+#define MVEBU_SW_LINK_CTRL_REG		(1)
+#define MVEBU_SW_PORT_CTRL_REG		(4)
+
+/* Global 2 Registers */
+#define MVEBU_G2_SMI_PHY_CMD_REG	(24)
+#define MVEBU_G2_SMI_PHY_DATA_REG	(25)
+
 int board_early_init_f(void)
 {
 	const void *blob = gd->fdt_blob;
@@ -156,3 +181,69 @@ int board_xhci_enable(void)
 
 	return 0;
 }
+
+/* Helper function for accessing switch devices in multi-chip connection mode */
+static int mii_multi_chip_mode_write(struct mii_dev *bus, int dev_smi_addr,
+				     int smi_addr, int reg, u16 value)
+{
+	u16 smi_cmd = 0;
+
+	if (bus->write(bus, dev_smi_addr, 0,
+		       MVEBU_SW_SMI_DATA_REG, value) != 0) {
+		printf("Error writing to the PHY addr=%02x reg=%02x\n",
+		       smi_addr, reg);
+		return -EFAULT;
+	}
+
+	smi_cmd = (1 << SW_SMI_CMD_SMI_BUSY_OFF) |
+		  (1 << SW_SMI_CMD_SMI_MODE_OFF) |
+		  (1 << SW_SMI_CMD_SMI_OP_OFF) |
+		  (smi_addr << SW_SMI_CMD_DEV_ADDR_OFF) |
+		  (reg << SW_SMI_CMD_REG_ADDR_OFF);
+	if (bus->write(bus, dev_smi_addr, 0,
+		       MVEBU_SW_SMI_CMD_REG, smi_cmd) != 0) {
+		printf("Error writing to the PHY addr=%02x reg=%02x\n",
+		       smi_addr, reg);
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+/* Bring-up board-specific network stuff */
+int board_network_enable(struct mii_dev *bus)
+{
+	if (!of_machine_is_compatible("marvell,armada-3720-espressobin"))
+		return 0;
+
+	/*
+	 * FIXME: remove this code once Topaz driver gets available
+	 * A3720 Community Board Only
+	 * Configure Topaz switch (88E6341)
+	 * Set port 0,1,2,3 to forwarding Mode (through Switch Port registers)
+	 */
+	mii_multi_chip_mode_write(bus, 1, MVEBU_PORT_CTRL_SMI_ADDR(0),
+				  MVEBU_SW_PORT_CTRL_REG, 0x7f);
+	mii_multi_chip_mode_write(bus, 1, MVEBU_PORT_CTRL_SMI_ADDR(1),
+				  MVEBU_SW_PORT_CTRL_REG, 0x7f);
+	mii_multi_chip_mode_write(bus, 1, MVEBU_PORT_CTRL_SMI_ADDR(2),
+				  MVEBU_SW_PORT_CTRL_REG, 0x7f);
+	mii_multi_chip_mode_write(bus, 1, MVEBU_PORT_CTRL_SMI_ADDR(3),
+				  MVEBU_SW_PORT_CTRL_REG, 0x7f);
+
+	/* RGMII Delay on Port 0 (CPU port), force link to 1000Mbps */
+	mii_multi_chip_mode_write(bus, 1, MVEBU_PORT_CTRL_SMI_ADDR(0),
+				  MVEBU_SW_LINK_CTRL_REG, 0xe002);
+
+	/* Power up PHY 1, 2, 3 (through Global 2 registers) */
+	mii_multi_chip_mode_write(bus, 1, MVEBU_SW_G2_SMI_ADDR,
+				  MVEBU_G2_SMI_PHY_DATA_REG, 0x1140);
+	mii_multi_chip_mode_write(bus, 1, MVEBU_SW_G2_SMI_ADDR,
+				  MVEBU_G2_SMI_PHY_CMD_REG, 0x9620);
+	mii_multi_chip_mode_write(bus, 1, MVEBU_SW_G2_SMI_ADDR,
+				  MVEBU_G2_SMI_PHY_CMD_REG, 0x9640);
+	mii_multi_chip_mode_write(bus, 1, MVEBU_SW_G2_SMI_ADDR,
+				  MVEBU_G2_SMI_PHY_CMD_REG, 0x9660);
+
+	return 0;
+}
-- 
2.7.4

[U-Boot] [PATCH v2 09/12] arm64: dts: Add device tree for ESPRESSOBin board

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
Changes for v2:
- No changes

 arch/arm/dts/Makefile                    |   1 +
 arch/arm/dts/armada-3720-espressobin.dts | 135 +++++++++++++++++++++++++++++++
 2 files changed, 136 insertions(+)
 create mode 100644 arch/arm/dts/armada-3720-espressobin.dts

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index eb68c20..d85210c 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -70,6 +70,7 @@ dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
 
 dtb-$(CONFIG_ARCH_MVEBU) +=			\
 	armada-3720-db.dtb			\
+	armada-3720-espressobin.dtb		\
 	armada-375-db.dtb			\
 	armada-388-clearfog.dtb			\
 	armada-388-gp.dtb			\
diff --git a/arch/arm/dts/armada-3720-espressobin.dts b/arch/arm/dts/armada-3720-espressobin.dts
new file mode 100644
index 0000000..aa6587a
--- /dev/null
+++ b/arch/arm/dts/armada-3720-espressobin.dts
@@ -0,0 +1,135 @@
+/*
+ * Device Tree file for Marvell Armada 3720 community board
+ * (ESPRESSOBin)
+ * Copyright (C) 2016 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Konstantin Porotchkin <kostap@marvell.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "armada-372x.dtsi"
+
+/ {
+	model = "Marvell Armada 3720 Community Board ESPRESSOBin";
+	compatible = "marvell,armada-3720-espressobin", "marvell,armada3720", "marvell,armada3710";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		ethernet0 = &eth0;
+		i2c0 = &i2c0;
+		spi0 = &spi0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+	};
+};
+
+&comphy {
+	max-lanes = <3>;
+	phy0 {
+		phy-type = <PHY_TYPE_PEX0>;
+		phy-speed = <PHY_SPEED_2_5G>;
+	};
+
+	phy1 {
+		phy-type = <PHY_TYPE_USB3_HOST0>;
+		phy-speed = <PHY_SPEED_5G>;
+	};
+
+	phy2 {
+		phy-type = <PHY_TYPE_SATA0>;
+		phy-speed = <PHY_SPEED_5G>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy_addr = <0x1>;
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+/* CON3 */
+&sata {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	spi-flash at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p128", "spi-flash";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+	};
+};
+
+/* Exported on the micro USB connector CON32 through an FTDI */
+&uart0 {
+	status = "okay";
+};
+
+/* CON29 */
+&usb2 {
+	status = "okay";
+};
+
+/* CON31 */
+&usb3 {
+	status = "okay";
+};
-- 
2.7.4

[U-Boot] [PATCH v2 10/12] arm64: mvebu: Add default config for ESPRESSOBin board

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Add initial default configuration for Marvell ESPRESSOBin
community board based on Aramda-3720 SoC

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
Changes for v2:
- Use the new target name TARGET_MVEBU_ARMADA_37XX

 configs/mvebu_espressobin-88f3720_defconfig | 67 +++++++++++++++++++++++++++++
 1 file changed, 67 insertions(+)
 create mode 100644 configs/mvebu_espressobin-88f3720_defconfig

diff --git a/configs/mvebu_espressobin-88f3720_defconfig b/configs/mvebu_espressobin-88f3720_defconfig
new file mode 100644
index 0000000..d1749bc
--- /dev/null
+++ b/configs/mvebu_espressobin-88f3720_defconfig
@@ -0,0 +1,67 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_MVEBU_ARMADA_37XX=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-3720-espressobin"
+CONFIG_AHCI=y
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_ARCH_EARLY_INIT_R=y
+CONFIG_BOARD_EARLY_INIT_F=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_FPGA is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_MAC_PARTITION=y
+CONFIG_ISO_PARTITION=y
+CONFIG_EFI_PARTITION=y
+CONFIG_CMD_MVEBU_BUBT=y
+CONFIG_SHA1=y
+CONFIG_SHA256=y
+CONFIG_BLOCK_CACHE=y
+CONFIG_DM_I2C=y
+CONFIG_DM_I2C_COMPAT=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_XENON=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_PHYLIB=y
+CONFIG_MVEBU_COMPHY_SUPPORT=y
+# CONFIG_SPL_SERIAL_PRESENT is not set
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_MVEBU_A3700_UART=y
+CONFIG_DEBUG_UART_BASE=0xd0012000
+CONFIG_DEBUG_UART_CLOCK=25804800
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_MVEBU_A3700_UART=y
+CONFIG_MVEBU_A3700_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_STORAGE=y
-- 
2.7.4

[U-Boot] [PATCH v2 11/12] arm64: a37xx: Disable DB configurations on ESPRESSOBin board

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Bypass XHCI and AHCi board configuration flow on ESPRESSOBin
community board.
The community board does not have i2c expander and USB VBUS
is always on, so the scan for AHCi and USB devices can be
faster without unneded configurations.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
Changes for v2:
- Check if the mashine is NOT compatible with DB
  instead of checking that if machine is compatible with ESPRESSOBin:wq

 board/Marvell/mvebu_armada-37xx/board.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/board/Marvell/mvebu_armada-37xx/board.c b/board/Marvell/mvebu_armada-37xx/board.c
index b9878bf..8dc1f46 100644
--- a/board/Marvell/mvebu_armada-37xx/board.c
+++ b/board/Marvell/mvebu_armada-37xx/board.c
@@ -21,6 +21,7 @@ DECLARE_GLOBAL_DATA_PTR;
 #define I2C_IO_REG_0_SATA_OFF	2
 #define I2C_IO_REG_0_USB_H_OFF	1
 
+/* The pin control values are the same for DB and Espressobin */
 #define PINCTRL_NB_REG_VALUE	0x000173fa
 #define PINCTRL_SB_REG_VALUE	0x00007a23
 
@@ -90,6 +91,10 @@ int board_ahci_enable(void)
 	int ret;
 	u8 buf[8];
 
+	/* Only DB requres this configuration */
+	if (!of_machine_is_compatible("marvell,armada-3720-db"))
+		return 0;
+
 	/* Configure IO exander PCA9555: 7bit address 0x22 */
 	ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
 	if (ret) {
@@ -124,6 +129,10 @@ int board_xhci_enable(void)
 	int ret;
 	u8 buf[8];
 
+	/* Only DB requres this configuration */
+	if (!of_machine_is_compatible("marvell,armada-3720-db"))
+		return 0;
+
 	/* Configure IO exander PCA9555: 7bit address 0x22 */
 	ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
 	if (ret) {
-- 
2.7.4

[U-Boot] [PATCH v2 12/12] arm64: a37xx: Remove DM_I2C_COMPAT from the board config

[kostap at marvell.com]

From: Konstantin Porotchkin <kostap@marvell.com>

Remove DM_I2C_COMPAT from the board configurations for
Armada 37xx platform boards for supressing the buid tim
warning.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
---
Changes for v2:
- This patch was missing in v1

 configs/mvebu_db-88f3720_defconfig          | 1 -
 configs/mvebu_espressobin-88f3720_defconfig | 1 -
 2 files changed, 2 deletions(-)

diff --git a/configs/mvebu_db-88f3720_defconfig b/configs/mvebu_db-88f3720_defconfig
index bdb96e9..3e548a8 100644
--- a/configs/mvebu_db-88f3720_defconfig
+++ b/configs/mvebu_db-88f3720_defconfig
@@ -38,7 +38,6 @@ CONFIG_SHA1=y
 CONFIG_SHA256=y
 CONFIG_BLOCK_CACHE=y
 CONFIG_DM_I2C=y
-CONFIG_DM_I2C_COMPAT=y
 CONFIG_MISC=y
 CONFIG_DM_MMC=y
 CONFIG_MMC_SDHCI=y
diff --git a/configs/mvebu_espressobin-88f3720_defconfig b/configs/mvebu_espressobin-88f3720_defconfig
index d1749bc..f02ae64 100644
--- a/configs/mvebu_espressobin-88f3720_defconfig
+++ b/configs/mvebu_espressobin-88f3720_defconfig
@@ -38,7 +38,6 @@ CONFIG_SHA1=y
 CONFIG_SHA256=y
 CONFIG_BLOCK_CACHE=y
 CONFIG_DM_I2C=y
-CONFIG_DM_I2C_COMPAT=y
 CONFIG_MISC=y
 CONFIG_DM_MMC=y
 CONFIG_MMC_SDHCI=y
-- 
2.7.4

[U-Boot] [PATCH v2 08/12] mvebu: a37xx: Add init for ESPRESSBin Topaz switch

[Joe Hershberger]

On Thu, Feb 16, 2017 at 5:52 AM,  <kostap@marvell.com> wrote:
> From: Konstantin Porotchkin <kostap@marvell.com>
>
> Implement the board-specific network init function for
> ESPRESSOBin community board, setting the on-board Topaz
> switch port to forward mode and allow network connection
> through any of the available Etherenet ports.
>
> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
> Cc: Stefan Roese <sr@denx.de>
> Cc: Igal Liberman <igall@marvell.com>
> Cc: Nadav Haklai <nadavh@marvell.com>
> Cc: Joe Hershberger <joe.hershberger@ni.com>

Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>

[U-Boot] [PATCH v2 01/12] arm64: mvebu: Rename the db-88f3720 to armada-37xx platform

[Stefan Roese]

On 16.02.2017 12:52, kostap at marvell.com wrote:
> From: Konstantin Porotchkin <kostap@marvell.com>
>
> Modify the file names and deifinitions relater to Marvell
> db-77f3720 board support. Convert these names to more generic
> armada-37xx platform for future addition of more boards
> based on the same SoC family.
>
> Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
> Cc: Stefan Roese <sr@denx.de>
> Cc: Igal Liberman <igall@marvell.com>
> Cc: Nadav Haklai <nadavh@marvell.com>

Complete series applied to u-boot-mavell/master.

Thanks,
Stefan