* [PATCH V2 0/3] Add Spreadtrum SP9860G support
@ 2017-02-21 6:55 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon, arnd
Cc: orson.zhai, sudeep.holla, linux-kernel, devicetree,
linux-arm-kernel, zhang.lyra
SC9860 is a Spreadtrum SoC with eight Cortex A53, which are divided
into 4 Big cores and 4 little cores.
This patch-set only provides a basic configuration for SC9860 in device
tree to make it run to console. We will continue to submit other drivers
later on, which are using on Spreadtrum's SoCs.
Changes from v1:
* Removed useless idle-state node 'deep_sleep' from DT
* Removed useless property 'sc-id' from DT
* Removed 'clock-frequency' property from the node 'timer'
* Added another compatible string '"arm,cortex-a53-pmu"' and property
'interrupt-affinity' for pmu
* Kept using the existed compatible string of sprd_serial driver, and added
a new one for sc9860 in DT.
Thanks,
Chunyan
Chunyan Zhang (1):
Documentation: sprd: Add bindings for SP9860G
Orson Zhai (1):
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
Wei Qiao (1):
serial: sprd: adjust TIMEOUT to a big value
Documentation/devicetree/bindings/arm/sprd.txt | 13 +-
.../devicetree/bindings/serial/sprd-uart.txt | 16 +-
arch/arm64/boot/dts/sprd/Makefile | 3 +-
arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 +++++++++++++++++++++
arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 +++
arch/arm64/boot/dts/sprd/whale2.dtsi | 70 +++
drivers/tty/serial/sprd_serial.c | 2 +-
7 files changed, 683 insertions(+), 8 deletions(-)
create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
--
2.7.4
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 0/3] Add Spreadtrum SP9860G support
@ 2017-02-21 6:55 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon, arnd
Cc: devicetree, orson.zhai, zhang.lyra, linux-kernel, sudeep.holla,
linux-arm-kernel
SC9860 is a Spreadtrum SoC with eight Cortex A53, which are divided
into 4 Big cores and 4 little cores.
This patch-set only provides a basic configuration for SC9860 in device
tree to make it run to console. We will continue to submit other drivers
later on, which are using on Spreadtrum's SoCs.
Changes from v1:
* Removed useless idle-state node 'deep_sleep' from DT
* Removed useless property 'sc-id' from DT
* Removed 'clock-frequency' property from the node 'timer'
* Added another compatible string '"arm,cortex-a53-pmu"' and property
'interrupt-affinity' for pmu
* Kept using the existed compatible string of sprd_serial driver, and added
a new one for sc9860 in DT.
Thanks,
Chunyan
Chunyan Zhang (1):
Documentation: sprd: Add bindings for SP9860G
Orson Zhai (1):
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
Wei Qiao (1):
serial: sprd: adjust TIMEOUT to a big value
Documentation/devicetree/bindings/arm/sprd.txt | 13 +-
.../devicetree/bindings/serial/sprd-uart.txt | 16 +-
arch/arm64/boot/dts/sprd/Makefile | 3 +-
arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 +++++++++++++++++++++
arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 +++
arch/arm64/boot/dts/sprd/whale2.dtsi | 70 +++
drivers/tty/serial/sprd_serial.c | 2 +-
7 files changed, 683 insertions(+), 8 deletions(-)
create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
--
2.7.4
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 0/3] Add Spreadtrum SP9860G support
@ 2017-02-21 6:55 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: linux-arm-kernel
SC9860 is a Spreadtrum SoC with eight Cortex A53, which are divided
into 4 Big cores and 4 little cores.
This patch-set only provides a basic configuration for SC9860 in device
tree to make it run to console. We will continue to submit other drivers
later on, which are using on Spreadtrum's SoCs.
Changes from v1:
* Removed useless idle-state node 'deep_sleep' from DT
* Removed useless property 'sc-id' from DT
* Removed 'clock-frequency' property from the node 'timer'
* Added another compatible string '"arm,cortex-a53-pmu"' and property
'interrupt-affinity' for pmu
* Kept using the existed compatible string of sprd_serial driver, and added
a new one for sc9860 in DT.
Thanks,
Chunyan
Chunyan Zhang (1):
Documentation: sprd: Add bindings for SP9860G
Orson Zhai (1):
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
Wei Qiao (1):
serial: sprd: adjust TIMEOUT to a big value
Documentation/devicetree/bindings/arm/sprd.txt | 13 +-
.../devicetree/bindings/serial/sprd-uart.txt | 16 +-
arch/arm64/boot/dts/sprd/Makefile | 3 +-
arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 +++++++++++++++++++++
arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 +++
arch/arm64/boot/dts/sprd/whale2.dtsi | 70 +++
drivers/tty/serial/sprd_serial.c | 2 +-
7 files changed, 683 insertions(+), 8 deletions(-)
create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
--
2.7.4
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
2017-02-21 6:55 ` Chunyan Zhang
(?)
@ 2017-02-21 6:55 ` Chunyan Zhang
-1 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon, arnd
Cc: orson.zhai, sudeep.holla, linux-kernel, devicetree,
linux-arm-kernel, zhang.lyra
From: Orson Zhai <orson.zhai@spreadtrum.com>
SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
and sp9860g dts is for the board level.
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
---
arch/arm64/boot/dts/sprd/Makefile | 3 +-
arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
4 files changed, 659 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
index b658c5e..f0535e6 100644
--- a/arch/arm64/boot/dts/sprd/Makefile
+++ b/arch/arm64/boot/dts/sprd/Makefile
@@ -1,4 +1,5 @@
-dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
+dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
+ sp9860g-1h10.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
new file mode 100644
index 0000000..73deb4e
--- /dev/null
+++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
@@ -0,0 +1,531 @@
+/*
+ * Spreadtrum SP9860 SoC DTS file
+ *
+ * Copyright (C) 2016, Spreadtrum Communications Inc.
+ *
+ * This file is licensed under a dual GPLv2 or X11 license.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "whale2.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+ core1 {
+ cpu = <&CPU1>;
+ };
+ core2 {
+ cpu = <&CPU2>;
+ };
+ core3 {
+ cpu = <&CPU3>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&CPU4>;
+ };
+ core1 {
+ cpu = <&CPU5>;
+ };
+ core2 {
+ cpu = <&CPU6>;
+ };
+ core3 {
+ cpu = <&CPU7>;
+ };
+ };
+ };
+
+ CPU0: cpu@530000 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530000>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU1: cpu@530001 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530001>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU2: cpu@530002 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530002>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU3: cpu@530003 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530003>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU4: cpu@530100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530100>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU5: cpu@530101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530101>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU6: cpu@530102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530102>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU7: cpu@530103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530103>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+ };
+
+ idle-states{
+ entry-method = "arm,psci";
+
+ CORE_PD: core_pd {
+ compatible = "arm,idle-state";
+ entry-latency-us = <1000>;
+ exit-latency-us = <700>;
+ min-residency-us = <2500>;
+ local-timer-stop;
+ arm,psci-suspend-param = <0x00010002>;
+ };
+
+ CLUSTER_PD: cluster_pd {
+ compatible = "arm,idle-state";
+ entry-latency-us = <1000>;
+ exit-latency-us = <1000>;
+ min-residency-us = <3000>;
+ local-timer-stop;
+ arm,psci-suspend-param = <0x01010003>;
+ };
+ };
+
+ gic: interrupt-controller@12001000 {
+ compatible = "arm,gic-400";
+ reg = <0 0x12001000 0 0x1000>,
+ <0 0x12002000 0 0x2000>,
+ <0 0x12004000 0 0x2000>,
+ <0 0x12006000 0 0x2000>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
+ interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&CPU0>,
+ <&CPU1>,
+ <&CPU2>,
+ <&CPU3>,
+ <&CPU4>,
+ <&CPU5>,
+ <&CPU6>,
+ <&CPU7>;
+ };
+
+ soc {
+ soc_funnel: funnel@10001000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x10001000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ soc_funnel_out_port: endpoint {
+ remote-endpoint = <&etb_in>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ soc_funnel_in_port: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&main_funnel_out_port>;
+ };
+ };
+ };
+ };
+
+ etb@10003000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x10003000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ port {
+ etb_in: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&soc_funnel_out_port>;
+ };
+ };
+ };
+
+ cluster0_funnel: funnel@11001000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x11001000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ cluster0_funnel_out_port: endpoint {
+ remote-endpoint =
+ <&cluster0_etf_in>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ cluster0_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm0_out>;
+ };
+ };
+
+ port@2 {
+ reg = <1>;
+ cluster0_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm1_out>;
+ };
+ };
+
+ port@3 {
+ reg = <2>;
+ cluster0_funnel_in_port2: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm2_out>;
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ cluster0_funnel_in_port3: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm3_out>;
+ };
+ };
+ };
+ };
+
+ cluster1_funnel: funnel@11002000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x11002000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ cluster1_funnel_out_port: endpoint {
+ remote-endpoint =
+ <&cluster1_etf_in>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ cluster1_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm4_out>;
+ };
+ };
+
+ port@2 {
+ reg = <1>;
+ cluster1_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm5_out>;
+ };
+ };
+
+ port@3 {
+ reg = <2>;
+ cluster1_funnel_in_port2: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm6_out>;
+ };
+ };
+
+ port@4 {
+ reg = <3>;
+ cluster1_funnel_in_port3: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm7_out>;
+ };
+ };
+ };
+ };
+
+ cluster0_etf: etf@11003000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x11003000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port@0 {
+ cluster0_etf_out: endpoint {
+ remote-endpoint =
+ <&main_funnel_in_port0>;
+ };
+ };
+
+ port@1 {
+ cluster0_etf_in: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster0_funnel_out_port>;
+ };
+ };
+ };
+
+ cluster1_etf: etf@11004000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x11004000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port@0 {
+ cluster1_etf_out: endpoint {
+ remote-endpoint =
+ <&main_funnel_in_port1>;
+ };
+ };
+
+ port@1 {
+ cluster1_etf_in: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster1_funnel_out_port>;
+ };
+ };
+ };
+
+ main_funnel: funnel@11005000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x11005000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ main_funnel_out_port: endpoint {
+ remote-endpoint =
+ <&soc_funnel_in_port>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ main_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster0_etf_out>;
+ };
+ };
+
+ port@2 {
+ reg = <1>;
+ main_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster1_etf_out>;
+ };
+ };
+ };
+ };
+
+ etm@11440000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11440000 0 0x1000>;
+ cpu = <&CPU0>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm0_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port0>;
+ };
+ };
+ };
+
+ etm@11540000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11540000 0 0x1000>;
+ cpu = <&CPU1>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm1_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port1>;
+ };
+ };
+ };
+
+ etm@11640000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11640000 0 0x1000>;
+ cpu = <&CPU2>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm2_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port2>;
+ };
+ };
+ };
+
+ etm@11740000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11740000 0 0x1000>;
+ cpu = <&CPU3>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm3_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port3>;
+ };
+ };
+ };
+
+ etm@11840000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11840000 0 0x1000>;
+ cpu = <&CPU4>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm4_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port0>;
+ };
+ };
+ };
+
+ etm@11940000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11940000 0 0x1000>;
+ cpu = <&CPU5>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm5_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port1>;
+ };
+ };
+ };
+
+ etm@11a40000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11a40000 0 0x1000>;
+ cpu = <&CPU6>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm6_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port2>;
+ };
+ };
+ };
+
+ etm@11b40000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11b40000 0 0x1000>;
+ cpu = <&CPU7>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm7_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port3>;
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
new file mode 100644
index 0000000..5faa452
--- /dev/null
+++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
@@ -0,0 +1,56 @@
+/*
+ * Spreadtrum SP9860g board DTS file
+ *
+ * Copyright (C) 2017, Spreadtrum Communications Inc.
+ *
+ * This file is licensed under a dual GPLv2 or X11 license.
+ */
+
+/dts-v1/;
+
+#include "sc9860.dtsi"
+
+/ {
+ model = "Spreadtrum SP9860G 3GFHD Board";
+
+ compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
+
+ aliases {
+ serial0 = &uart0; /* for Bluetooth */
+ serial1 = &uart1; /* UART console */
+ serial2 = &uart2; /* Reserved */
+ serial3 = &uart3; /* for GPS */
+ };
+
+ memory{
+ device_type = "memory";
+ reg = <0x0 0x80000000 0 0x60000000>,
+ <0x1 0x80000000 0 0x60000000>;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
new file mode 100644
index 0000000..64f06d9
--- /dev/null
+++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
@@ -0,0 +1,70 @@
+/*
+ * Spreadtrum Whale2 SoC platform peripherals DTS file
+ *
+ * Copyright (C) 2016, Spreadtrum Communications Inc.
+ *
+ * This file is licensed under a dual GPLv2 or X11 license.
+ */
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ soc: soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ap-apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x0 0x70000000 0x10000000>;
+
+ uart0: serial@70000000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x000000 0x100>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+
+ uart1: serial@70100000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x100000 0x100>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+
+ uart2: serial@70200000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x200000 0x100>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+
+ uart3: serial@70300000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x300000 0x100>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+ };
+
+ ext_26m: ext-26m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "ext_26m";
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-21 6:55 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon, arnd
Cc: devicetree, orson.zhai, zhang.lyra, linux-kernel, sudeep.holla,
linux-arm-kernel
From: Orson Zhai <orson.zhai@spreadtrum.com>
SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
and sp9860g dts is for the board level.
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
---
arch/arm64/boot/dts/sprd/Makefile | 3 +-
arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
4 files changed, 659 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
index b658c5e..f0535e6 100644
--- a/arch/arm64/boot/dts/sprd/Makefile
+++ b/arch/arm64/boot/dts/sprd/Makefile
@@ -1,4 +1,5 @@
-dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
+dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
+ sp9860g-1h10.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
new file mode 100644
index 0000000..73deb4e
--- /dev/null
+++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
@@ -0,0 +1,531 @@
+/*
+ * Spreadtrum SP9860 SoC DTS file
+ *
+ * Copyright (C) 2016, Spreadtrum Communications Inc.
+ *
+ * This file is licensed under a dual GPLv2 or X11 license.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "whale2.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+ core1 {
+ cpu = <&CPU1>;
+ };
+ core2 {
+ cpu = <&CPU2>;
+ };
+ core3 {
+ cpu = <&CPU3>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&CPU4>;
+ };
+ core1 {
+ cpu = <&CPU5>;
+ };
+ core2 {
+ cpu = <&CPU6>;
+ };
+ core3 {
+ cpu = <&CPU7>;
+ };
+ };
+ };
+
+ CPU0: cpu@530000 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530000>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU1: cpu@530001 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530001>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU2: cpu@530002 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530002>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU3: cpu@530003 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530003>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU4: cpu@530100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530100>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU5: cpu@530101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530101>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU6: cpu@530102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530102>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU7: cpu@530103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530103>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+ };
+
+ idle-states{
+ entry-method = "arm,psci";
+
+ CORE_PD: core_pd {
+ compatible = "arm,idle-state";
+ entry-latency-us = <1000>;
+ exit-latency-us = <700>;
+ min-residency-us = <2500>;
+ local-timer-stop;
+ arm,psci-suspend-param = <0x00010002>;
+ };
+
+ CLUSTER_PD: cluster_pd {
+ compatible = "arm,idle-state";
+ entry-latency-us = <1000>;
+ exit-latency-us = <1000>;
+ min-residency-us = <3000>;
+ local-timer-stop;
+ arm,psci-suspend-param = <0x01010003>;
+ };
+ };
+
+ gic: interrupt-controller@12001000 {
+ compatible = "arm,gic-400";
+ reg = <0 0x12001000 0 0x1000>,
+ <0 0x12002000 0 0x2000>,
+ <0 0x12004000 0 0x2000>,
+ <0 0x12006000 0 0x2000>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
+ interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&CPU0>,
+ <&CPU1>,
+ <&CPU2>,
+ <&CPU3>,
+ <&CPU4>,
+ <&CPU5>,
+ <&CPU6>,
+ <&CPU7>;
+ };
+
+ soc {
+ soc_funnel: funnel@10001000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x10001000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ soc_funnel_out_port: endpoint {
+ remote-endpoint = <&etb_in>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ soc_funnel_in_port: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&main_funnel_out_port>;
+ };
+ };
+ };
+ };
+
+ etb@10003000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x10003000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ port {
+ etb_in: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&soc_funnel_out_port>;
+ };
+ };
+ };
+
+ cluster0_funnel: funnel@11001000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x11001000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ cluster0_funnel_out_port: endpoint {
+ remote-endpoint =
+ <&cluster0_etf_in>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ cluster0_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm0_out>;
+ };
+ };
+
+ port@2 {
+ reg = <1>;
+ cluster0_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm1_out>;
+ };
+ };
+
+ port@3 {
+ reg = <2>;
+ cluster0_funnel_in_port2: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm2_out>;
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ cluster0_funnel_in_port3: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm3_out>;
+ };
+ };
+ };
+ };
+
+ cluster1_funnel: funnel@11002000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x11002000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ cluster1_funnel_out_port: endpoint {
+ remote-endpoint =
+ <&cluster1_etf_in>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ cluster1_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm4_out>;
+ };
+ };
+
+ port@2 {
+ reg = <1>;
+ cluster1_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm5_out>;
+ };
+ };
+
+ port@3 {
+ reg = <2>;
+ cluster1_funnel_in_port2: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm6_out>;
+ };
+ };
+
+ port@4 {
+ reg = <3>;
+ cluster1_funnel_in_port3: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm7_out>;
+ };
+ };
+ };
+ };
+
+ cluster0_etf: etf@11003000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x11003000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port@0 {
+ cluster0_etf_out: endpoint {
+ remote-endpoint =
+ <&main_funnel_in_port0>;
+ };
+ };
+
+ port@1 {
+ cluster0_etf_in: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster0_funnel_out_port>;
+ };
+ };
+ };
+
+ cluster1_etf: etf@11004000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x11004000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port@0 {
+ cluster1_etf_out: endpoint {
+ remote-endpoint =
+ <&main_funnel_in_port1>;
+ };
+ };
+
+ port@1 {
+ cluster1_etf_in: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster1_funnel_out_port>;
+ };
+ };
+ };
+
+ main_funnel: funnel@11005000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x11005000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ main_funnel_out_port: endpoint {
+ remote-endpoint =
+ <&soc_funnel_in_port>;
+ };
+ };
+
+ port@1 {
+ reg = <0>;
+ main_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster0_etf_out>;
+ };
+ };
+
+ port@2 {
+ reg = <1>;
+ main_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster1_etf_out>;
+ };
+ };
+ };
+ };
+
+ etm@11440000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11440000 0 0x1000>;
+ cpu = <&CPU0>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm0_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port0>;
+ };
+ };
+ };
+
+ etm@11540000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11540000 0 0x1000>;
+ cpu = <&CPU1>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm1_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port1>;
+ };
+ };
+ };
+
+ etm@11640000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11640000 0 0x1000>;
+ cpu = <&CPU2>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm2_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port2>;
+ };
+ };
+ };
+
+ etm@11740000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11740000 0 0x1000>;
+ cpu = <&CPU3>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm3_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port3>;
+ };
+ };
+ };
+
+ etm@11840000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11840000 0 0x1000>;
+ cpu = <&CPU4>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm4_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port0>;
+ };
+ };
+ };
+
+ etm@11940000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11940000 0 0x1000>;
+ cpu = <&CPU5>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm5_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port1>;
+ };
+ };
+ };
+
+ etm@11a40000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11a40000 0 0x1000>;
+ cpu = <&CPU6>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm6_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port2>;
+ };
+ };
+ };
+
+ etm@11b40000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11b40000 0 0x1000>;
+ cpu = <&CPU7>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm7_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port3>;
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
new file mode 100644
index 0000000..5faa452
--- /dev/null
+++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
@@ -0,0 +1,56 @@
+/*
+ * Spreadtrum SP9860g board DTS file
+ *
+ * Copyright (C) 2017, Spreadtrum Communications Inc.
+ *
+ * This file is licensed under a dual GPLv2 or X11 license.
+ */
+
+/dts-v1/;
+
+#include "sc9860.dtsi"
+
+/ {
+ model = "Spreadtrum SP9860G 3GFHD Board";
+
+ compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
+
+ aliases {
+ serial0 = &uart0; /* for Bluetooth */
+ serial1 = &uart1; /* UART console */
+ serial2 = &uart2; /* Reserved */
+ serial3 = &uart3; /* for GPS */
+ };
+
+ memory{
+ device_type = "memory";
+ reg = <0x0 0x80000000 0 0x60000000>,
+ <0x1 0x80000000 0 0x60000000>;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
new file mode 100644
index 0000000..64f06d9
--- /dev/null
+++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
@@ -0,0 +1,70 @@
+/*
+ * Spreadtrum Whale2 SoC platform peripherals DTS file
+ *
+ * Copyright (C) 2016, Spreadtrum Communications Inc.
+ *
+ * This file is licensed under a dual GPLv2 or X11 license.
+ */
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ soc: soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ap-apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x0 0x70000000 0x10000000>;
+
+ uart0: serial@70000000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x000000 0x100>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+
+ uart1: serial@70100000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x100000 0x100>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+
+ uart2: serial@70200000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x200000 0x100>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+
+ uart3: serial@70300000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x300000 0x100>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+ };
+
+ ext_26m: ext-26m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "ext_26m";
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-21 6:55 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: linux-arm-kernel
From: Orson Zhai <orson.zhai@spreadtrum.com>
SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
and sp9860g dts is for the board level.
Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
---
arch/arm64/boot/dts/sprd/Makefile | 3 +-
arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
4 files changed, 659 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
index b658c5e..f0535e6 100644
--- a/arch/arm64/boot/dts/sprd/Makefile
+++ b/arch/arm64/boot/dts/sprd/Makefile
@@ -1,4 +1,5 @@
-dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
+dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
+ sp9860g-1h10.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
new file mode 100644
index 0000000..73deb4e
--- /dev/null
+++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
@@ -0,0 +1,531 @@
+/*
+ * Spreadtrum SP9860 SoC DTS file
+ *
+ * Copyright (C) 2016, Spreadtrum Communications Inc.
+ *
+ * This file is licensed under a dual GPLv2 or X11 license.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "whale2.dtsi"
+
+/ {
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+ core1 {
+ cpu = <&CPU1>;
+ };
+ core2 {
+ cpu = <&CPU2>;
+ };
+ core3 {
+ cpu = <&CPU3>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&CPU4>;
+ };
+ core1 {
+ cpu = <&CPU5>;
+ };
+ core2 {
+ cpu = <&CPU6>;
+ };
+ core3 {
+ cpu = <&CPU7>;
+ };
+ };
+ };
+
+ CPU0: cpu at 530000 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530000>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU1: cpu at 530001 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530001>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU2: cpu at 530002 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530002>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU3: cpu at 530003 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530003>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU4: cpu at 530100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530100>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU5: cpu at 530101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530101>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU6: cpu at 530102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530102>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+
+ CPU7: cpu at 530103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x530103>;
+ enable-method = "psci";
+ cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
+ };
+ };
+
+ idle-states{
+ entry-method = "arm,psci";
+
+ CORE_PD: core_pd {
+ compatible = "arm,idle-state";
+ entry-latency-us = <1000>;
+ exit-latency-us = <700>;
+ min-residency-us = <2500>;
+ local-timer-stop;
+ arm,psci-suspend-param = <0x00010002>;
+ };
+
+ CLUSTER_PD: cluster_pd {
+ compatible = "arm,idle-state";
+ entry-latency-us = <1000>;
+ exit-latency-us = <1000>;
+ min-residency-us = <3000>;
+ local-timer-stop;
+ arm,psci-suspend-param = <0x01010003>;
+ };
+ };
+
+ gic: interrupt-controller at 12001000 {
+ compatible = "arm,gic-400";
+ reg = <0 0x12001000 0 0x1000>,
+ <0 0x12002000 0 0x2000>,
+ <0 0x12004000 0 0x2000>,
+ <0 0x12006000 0 0x2000>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
+ | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
+ interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&CPU0>,
+ <&CPU1>,
+ <&CPU2>,
+ <&CPU3>,
+ <&CPU4>,
+ <&CPU5>,
+ <&CPU6>,
+ <&CPU7>;
+ };
+
+ soc {
+ soc_funnel: funnel at 10001000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x10001000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ soc_funnel_out_port: endpoint {
+ remote-endpoint = <&etb_in>;
+ };
+ };
+
+ port at 1 {
+ reg = <0>;
+ soc_funnel_in_port: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&main_funnel_out_port>;
+ };
+ };
+ };
+ };
+
+ etb at 10003000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x10003000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ port {
+ etb_in: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&soc_funnel_out_port>;
+ };
+ };
+ };
+
+ cluster0_funnel: funnel at 11001000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x11001000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ cluster0_funnel_out_port: endpoint {
+ remote-endpoint =
+ <&cluster0_etf_in>;
+ };
+ };
+
+ port at 1 {
+ reg = <0>;
+ cluster0_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm0_out>;
+ };
+ };
+
+ port at 2 {
+ reg = <1>;
+ cluster0_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm1_out>;
+ };
+ };
+
+ port at 3 {
+ reg = <2>;
+ cluster0_funnel_in_port2: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm2_out>;
+ };
+ };
+
+ port at 4 {
+ reg = <4>;
+ cluster0_funnel_in_port3: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm3_out>;
+ };
+ };
+ };
+ };
+
+ cluster1_funnel: funnel at 11002000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x11002000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ cluster1_funnel_out_port: endpoint {
+ remote-endpoint =
+ <&cluster1_etf_in>;
+ };
+ };
+
+ port at 1 {
+ reg = <0>;
+ cluster1_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm4_out>;
+ };
+ };
+
+ port at 2 {
+ reg = <1>;
+ cluster1_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm5_out>;
+ };
+ };
+
+ port at 3 {
+ reg = <2>;
+ cluster1_funnel_in_port2: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm6_out>;
+ };
+ };
+
+ port at 4 {
+ reg = <3>;
+ cluster1_funnel_in_port3: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm7_out>;
+ };
+ };
+ };
+ };
+
+ cluster0_etf: etf at 11003000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x11003000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port at 0 {
+ cluster0_etf_out: endpoint {
+ remote-endpoint =
+ <&main_funnel_in_port0>;
+ };
+ };
+
+ port at 1 {
+ cluster0_etf_in: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster0_funnel_out_port>;
+ };
+ };
+ };
+
+ cluster1_etf: etf at 11004000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0 0x11004000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port at 0 {
+ cluster1_etf_out: endpoint {
+ remote-endpoint =
+ <&main_funnel_in_port1>;
+ };
+ };
+
+ port at 1 {
+ cluster1_etf_in: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster1_funnel_out_port>;
+ };
+ };
+ };
+
+ main_funnel: funnel at 11005000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0 0x11005000 0 0x1000>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ main_funnel_out_port: endpoint {
+ remote-endpoint =
+ <&soc_funnel_in_port>;
+ };
+ };
+
+ port at 1 {
+ reg = <0>;
+ main_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster0_etf_out>;
+ };
+ };
+
+ port at 2 {
+ reg = <1>;
+ main_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint =
+ <&cluster1_etf_out>;
+ };
+ };
+ };
+ };
+
+ etm at 11440000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11440000 0 0x1000>;
+ cpu = <&CPU0>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm0_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port0>;
+ };
+ };
+ };
+
+ etm at 11540000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11540000 0 0x1000>;
+ cpu = <&CPU1>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm1_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port1>;
+ };
+ };
+ };
+
+ etm at 11640000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11640000 0 0x1000>;
+ cpu = <&CPU2>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm2_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port2>;
+ };
+ };
+ };
+
+ etm at 11740000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11740000 0 0x1000>;
+ cpu = <&CPU3>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm3_out: endpoint {
+ remote-endpoint =
+ <&cluster0_funnel_in_port3>;
+ };
+ };
+ };
+
+ etm at 11840000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11840000 0 0x1000>;
+ cpu = <&CPU4>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm4_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port0>;
+ };
+ };
+ };
+
+ etm at 11940000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11940000 0 0x1000>;
+ cpu = <&CPU5>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm5_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port1>;
+ };
+ };
+ };
+
+ etm at 11a40000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11a40000 0 0x1000>;
+ cpu = <&CPU6>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm6_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port2>;
+ };
+ };
+ };
+
+ etm at 11b40000 {
+ compatible = "arm,coresight-etm4x", "arm,primecell";
+ reg = <0 0x11b40000 0 0x1000>;
+ cpu = <&CPU7>;
+ clocks = <&ext_26m>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm7_out: endpoint {
+ remote-endpoint =
+ <&cluster1_funnel_in_port3>;
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
new file mode 100644
index 0000000..5faa452
--- /dev/null
+++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
@@ -0,0 +1,56 @@
+/*
+ * Spreadtrum SP9860g board DTS file
+ *
+ * Copyright (C) 2017, Spreadtrum Communications Inc.
+ *
+ * This file is licensed under a dual GPLv2 or X11 license.
+ */
+
+/dts-v1/;
+
+#include "sc9860.dtsi"
+
+/ {
+ model = "Spreadtrum SP9860G 3GFHD Board";
+
+ compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
+
+ aliases {
+ serial0 = &uart0; /* for Bluetooth */
+ serial1 = &uart1; /* UART console */
+ serial2 = &uart2; /* Reserved */
+ serial3 = &uart3; /* for GPS */
+ };
+
+ memory{
+ device_type = "memory";
+ reg = <0x0 0x80000000 0 0x60000000>,
+ <0x1 0x80000000 0 0x60000000>;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
new file mode 100644
index 0000000..64f06d9
--- /dev/null
+++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
@@ -0,0 +1,70 @@
+/*
+ * Spreadtrum Whale2 SoC platform peripherals DTS file
+ *
+ * Copyright (C) 2016, Spreadtrum Communications Inc.
+ *
+ * This file is licensed under a dual GPLv2 or X11 license.
+ */
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ soc: soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ap-apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x0 0x70000000 0x10000000>;
+
+ uart0: serial at 70000000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x000000 0x100>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+
+ uart1: serial at 70100000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x100000 0x100>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+
+ uart2: serial at 70200000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x200000 0x100>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+
+ uart3: serial at 70300000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x300000 0x100>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
+ };
+
+ ext_26m: ext-26m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ clock-output-names = "ext_26m";
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH V2 2/3] Documentation: sprd: Add bindings for SP9860G
2017-02-21 6:55 ` Chunyan Zhang
(?)
@ 2017-02-21 6:55 ` Chunyan Zhang
-1 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon, arnd
Cc: orson.zhai, sudeep.holla, linux-kernel, devicetree,
linux-arm-kernel, zhang.lyra
Added support for Spreadtrum SP9860G board and SC9860 SoC.
This patch also revised bindings of SC9836 to make the format
more clear.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
---
Documentation/devicetree/bindings/arm/sprd.txt | 13 ++++++++-----
Documentation/devicetree/bindings/serial/sprd-uart.txt | 16 +++++++++++++++-
2 files changed, 23 insertions(+), 6 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/sprd.txt b/Documentation/devicetree/bindings/arm/sprd.txt
index 31a629d..3df034b 100644
--- a/Documentation/devicetree/bindings/arm/sprd.txt
+++ b/Documentation/devicetree/bindings/arm/sprd.txt
@@ -1,11 +1,14 @@
Spreadtrum SoC Platforms Device Tree Bindings
----------------------------------------------------
-Sharkl64 is a Spreadtrum's SoC Platform which is based
-on ARM 64-bit processor.
+SC9836 openphone Board
+Required root node properties:
+ - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
-SC9836 openphone board with SC9836 SoC based on the
-Sharkl64 Platform shall have the following properties.
+SC9860 SoC
+Required root node properties:
+ - compatible = "sprd,sc9860"
+SP9860G 3GFHD Board
Required root node properties:
- - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
+ - compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.txt b/Documentation/devicetree/bindings/serial/sprd-uart.txt
index 2aff0f2..f530cbb 100644
--- a/Documentation/devicetree/bindings/serial/sprd-uart.txt
+++ b/Documentation/devicetree/bindings/serial/sprd-uart.txt
@@ -1,7 +1,21 @@
* Spreadtrum serial UART
Required properties:
-- compatible: must be "sprd,sc9836-uart"
+- compatible must contain:
+ * "sprd,sc9836-uart" for SC9836 and all Spreadtrum SoCs
+ This also can be specific with:
+ * "sprd, sc9860-uart" for SC9860
+
- reg: offset and length of the register set for the device
- interrupts: exactly one interrupt specifier
- clocks: phandles to input clocks.
+
+Example:
+ uart0: serial@70000000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x000000 0x100>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH V2 2/3] Documentation: sprd: Add bindings for SP9860G
@ 2017-02-21 6:55 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon, arnd
Cc: devicetree, orson.zhai, zhang.lyra, linux-kernel, sudeep.holla,
linux-arm-kernel
Added support for Spreadtrum SP9860G board and SC9860 SoC.
This patch also revised bindings of SC9836 to make the format
more clear.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
---
Documentation/devicetree/bindings/arm/sprd.txt | 13 ++++++++-----
Documentation/devicetree/bindings/serial/sprd-uart.txt | 16 +++++++++++++++-
2 files changed, 23 insertions(+), 6 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/sprd.txt b/Documentation/devicetree/bindings/arm/sprd.txt
index 31a629d..3df034b 100644
--- a/Documentation/devicetree/bindings/arm/sprd.txt
+++ b/Documentation/devicetree/bindings/arm/sprd.txt
@@ -1,11 +1,14 @@
Spreadtrum SoC Platforms Device Tree Bindings
----------------------------------------------------
-Sharkl64 is a Spreadtrum's SoC Platform which is based
-on ARM 64-bit processor.
+SC9836 openphone Board
+Required root node properties:
+ - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
-SC9836 openphone board with SC9836 SoC based on the
-Sharkl64 Platform shall have the following properties.
+SC9860 SoC
+Required root node properties:
+ - compatible = "sprd,sc9860"
+SP9860G 3GFHD Board
Required root node properties:
- - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
+ - compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.txt b/Documentation/devicetree/bindings/serial/sprd-uart.txt
index 2aff0f2..f530cbb 100644
--- a/Documentation/devicetree/bindings/serial/sprd-uart.txt
+++ b/Documentation/devicetree/bindings/serial/sprd-uart.txt
@@ -1,7 +1,21 @@
* Spreadtrum serial UART
Required properties:
-- compatible: must be "sprd,sc9836-uart"
+- compatible must contain:
+ * "sprd,sc9836-uart" for SC9836 and all Spreadtrum SoCs
+ This also can be specific with:
+ * "sprd, sc9860-uart" for SC9860
+
- reg: offset and length of the register set for the device
- interrupts: exactly one interrupt specifier
- clocks: phandles to input clocks.
+
+Example:
+ uart0: serial@70000000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x000000 0x100>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH V2 2/3] Documentation: sprd: Add bindings for SP9860G
@ 2017-02-21 6:55 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: linux-arm-kernel
Added support for Spreadtrum SP9860G board and SC9860 SoC.
This patch also revised bindings of SC9836 to make the format
more clear.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
---
Documentation/devicetree/bindings/arm/sprd.txt | 13 ++++++++-----
Documentation/devicetree/bindings/serial/sprd-uart.txt | 16 +++++++++++++++-
2 files changed, 23 insertions(+), 6 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/sprd.txt b/Documentation/devicetree/bindings/arm/sprd.txt
index 31a629d..3df034b 100644
--- a/Documentation/devicetree/bindings/arm/sprd.txt
+++ b/Documentation/devicetree/bindings/arm/sprd.txt
@@ -1,11 +1,14 @@
Spreadtrum SoC Platforms Device Tree Bindings
----------------------------------------------------
-Sharkl64 is a Spreadtrum's SoC Platform which is based
-on ARM 64-bit processor.
+SC9836 openphone Board
+Required root node properties:
+ - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
-SC9836 openphone board with SC9836 SoC based on the
-Sharkl64 Platform shall have the following properties.
+SC9860 SoC
+Required root node properties:
+ - compatible = "sprd,sc9860"
+SP9860G 3GFHD Board
Required root node properties:
- - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
+ - compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.txt b/Documentation/devicetree/bindings/serial/sprd-uart.txt
index 2aff0f2..f530cbb 100644
--- a/Documentation/devicetree/bindings/serial/sprd-uart.txt
+++ b/Documentation/devicetree/bindings/serial/sprd-uart.txt
@@ -1,7 +1,21 @@
* Spreadtrum serial UART
Required properties:
-- compatible: must be "sprd,sc9836-uart"
+- compatible must contain:
+ * "sprd,sc9836-uart" for SC9836 and all Spreadtrum SoCs
+ This also can be specific with:
+ * "sprd, sc9860-uart" for SC9860
+
- reg: offset and length of the register set for the device
- interrupts: exactly one interrupt specifier
- clocks: phandles to input clocks.
+
+Example:
+ uart0: serial at 70000000 {
+ compatible = "sprd,sc9838-uart",
+ "sprd,sc9836-uart";
+ reg = <0x000000 0x100>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ext_26m>;
+ status = "disabled";
+ };
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH V2 3/3] serial: sprd: adjust TIMEOUT to a big value
2017-02-21 6:55 ` Chunyan Zhang
(?)
@ 2017-02-21 6:55 ` Chunyan Zhang
-1 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon, arnd
Cc: orson.zhai, sudeep.holla, linux-kernel, devicetree,
linux-arm-kernel, zhang.lyra
From: Wei Qiao <wei.qiao@spreadtrum.com>
SPRD_TIMEOUT was 256, which is too small to wait until the status
switched to workable in a while loop, so that the earlycon could
not work correctly.
Signed-off-by: Wei Qiao <wei.qiao@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
---
drivers/tty/serial/sprd_serial.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c
index 699447a..cc1a55e 100644
--- a/drivers/tty/serial/sprd_serial.c
+++ b/drivers/tty/serial/sprd_serial.c
@@ -36,7 +36,7 @@
#define SPRD_FIFO_SIZE 128
#define SPRD_DEF_RATE 26000000
#define SPRD_BAUD_IO_LIMIT 3000000
-#define SPRD_TIMEOUT 256
+#define SPRD_TIMEOUT 256000
/* the offset of serial registers and BITs for them */
/* data registers */
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH V2 3/3] serial: sprd: adjust TIMEOUT to a big value
@ 2017-02-21 6:55 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon, arnd
Cc: orson.zhai, sudeep.holla, linux-kernel, devicetree,
linux-arm-kernel, zhang.lyra
From: Wei Qiao <wei.qiao@spreadtrum.com>
SPRD_TIMEOUT was 256, which is too small to wait until the status
switched to workable in a while loop, so that the earlycon could
not work correctly.
Signed-off-by: Wei Qiao <wei.qiao@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
---
drivers/tty/serial/sprd_serial.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c
index 699447a..cc1a55e 100644
--- a/drivers/tty/serial/sprd_serial.c
+++ b/drivers/tty/serial/sprd_serial.c
@@ -36,7 +36,7 @@
#define SPRD_FIFO_SIZE 128
#define SPRD_DEF_RATE 26000000
#define SPRD_BAUD_IO_LIMIT 3000000
-#define SPRD_TIMEOUT 256
+#define SPRD_TIMEOUT 256000
/* the offset of serial registers and BITs for them */
/* data registers */
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* [PATCH V2 3/3] serial: sprd: adjust TIMEOUT to a big value
@ 2017-02-21 6:55 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-21 6:55 UTC (permalink / raw)
To: linux-arm-kernel
From: Wei Qiao <wei.qiao@spreadtrum.com>
SPRD_TIMEOUT was 256, which is too small to wait until the status
switched to workable in a while loop, so that the earlycon could
not work correctly.
Signed-off-by: Wei Qiao <wei.qiao@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
---
drivers/tty/serial/sprd_serial.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c
index 699447a..cc1a55e 100644
--- a/drivers/tty/serial/sprd_serial.c
+++ b/drivers/tty/serial/sprd_serial.c
@@ -36,7 +36,7 @@
#define SPRD_FIFO_SIZE 128
#define SPRD_DEF_RATE 26000000
#define SPRD_BAUD_IO_LIMIT 3000000
-#define SPRD_TIMEOUT 256
+#define SPRD_TIMEOUT 256000
/* the offset of serial registers and BITs for them */
/* data registers */
--
2.7.4
^ permalink raw reply related [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-21 10:57 ` Sudeep Holla
0 siblings, 0 replies; 48+ messages in thread
From: Sudeep Holla @ 2017-02-21 10:57 UTC (permalink / raw)
To: Chunyan Zhang
Cc: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon,
arnd, Sudeep Holla, orson.zhai, linux-kernel, devicetree,
linux-arm-kernel, zhang.lyra
On 21/02/17 06:55, Chunyan Zhang wrote:
> From: Orson Zhai <orson.zhai@spreadtrum.com>
>
> SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>
> According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> and sp9860g dts is for the board level.
>
> Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> ---
> arch/arm64/boot/dts/sprd/Makefile | 3 +-
> arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> 4 files changed, 659 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>
[...]
> diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> new file mode 100644
> index 0000000..73deb4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> @@ -0,0 +1,531 @@
> +/*
> + * Spreadtrum SP9860 SoC DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
[...]
> +
> + idle-states{
> + entry-method = "arm,psci";
> +
> + CORE_PD: core_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <700>;
> + min-residency-us = <2500>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x00010002>;
> + };
> +
> + CLUSTER_PD: cluster_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <1000>;
> + min-residency-us = <3000>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x01010003>;
> + };
Thanks for dropping the hacked up "deep sleep" state :)
This version looks fine to me.
--
Regards,
Sudeep
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-21 10:57 ` Sudeep Holla
0 siblings, 0 replies; 48+ messages in thread
From: Sudeep Holla @ 2017-02-21 10:57 UTC (permalink / raw)
To: Chunyan Zhang
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8,
arnd-r2nGTMty4D4, Sudeep Holla,
orson.zhai-lxIno14LUO0EEoCn2XhGlw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
zhang.lyra-Re5JQEeQqe8AvxtiuMwx3w
On 21/02/17 06:55, Chunyan Zhang wrote:
> From: Orson Zhai <orson.zhai-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
>
> SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>
> According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> and sp9860g dts is for the board level.
>
> Signed-off-by: Orson Zhai <orson.zhai-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
> Signed-off-by: Chunyan Zhang <chunyan.zhang-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
> ---
> arch/arm64/boot/dts/sprd/Makefile | 3 +-
> arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> 4 files changed, 659 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>
[...]
> diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> new file mode 100644
> index 0000000..73deb4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> @@ -0,0 +1,531 @@
> +/*
> + * Spreadtrum SP9860 SoC DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
[...]
> +
> + idle-states{
> + entry-method = "arm,psci";
> +
> + CORE_PD: core_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <700>;
> + min-residency-us = <2500>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x00010002>;
> + };
> +
> + CLUSTER_PD: cluster_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <1000>;
> + min-residency-us = <3000>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x01010003>;
> + };
Thanks for dropping the hacked up "deep sleep" state :)
This version looks fine to me.
--
Regards,
Sudeep
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-21 10:57 ` Sudeep Holla
0 siblings, 0 replies; 48+ messages in thread
From: Sudeep Holla @ 2017-02-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
On 21/02/17 06:55, Chunyan Zhang wrote:
> From: Orson Zhai <orson.zhai@spreadtrum.com>
>
> SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>
> According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> and sp9860g dts is for the board level.
>
> Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> ---
> arch/arm64/boot/dts/sprd/Makefile | 3 +-
> arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> 4 files changed, 659 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>
[...]
> diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> new file mode 100644
> index 0000000..73deb4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> @@ -0,0 +1,531 @@
> +/*
> + * Spreadtrum SP9860 SoC DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
[...]
> +
> + idle-states{
> + entry-method = "arm,psci";
> +
> + CORE_PD: core_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <700>;
> + min-residency-us = <2500>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x00010002>;
> + };
> +
> + CLUSTER_PD: cluster_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <1000>;
> + min-residency-us = <3000>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x01010003>;
> + };
Thanks for dropping the hacked up "deep sleep" state :)
This version looks fine to me.
--
Regards,
Sudeep
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-21 16:27 ` Mathieu Poirier
0 siblings, 0 replies; 48+ messages in thread
From: Mathieu Poirier @ 2017-02-21 16:27 UTC (permalink / raw)
To: Chunyan Zhang
Cc: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon,
arnd, devicetree, orson.zhai, zhang.lyra, linux-kernel,
sudeep.holla, linux-arm-kernel
On Tue, Feb 21, 2017 at 02:55:02PM +0800, Chunyan Zhang wrote:
> From: Orson Zhai <orson.zhai@spreadtrum.com>
Hello Chunyan,
>
> SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>
> According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> and sp9860g dts is for the board level.
>
> Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> ---
> arch/arm64/boot/dts/sprd/Makefile | 3 +-
> arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> 4 files changed, 659 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>
> diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> index b658c5e..f0535e6 100644
> --- a/arch/arm64/boot/dts/sprd/Makefile
> +++ b/arch/arm64/boot/dts/sprd/Makefile
> @@ -1,4 +1,5 @@
> -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> + sp9860g-1h10.dtb
>
> always := $(dtb-y)
> subdir-y := $(dts-dirs)
> diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> new file mode 100644
> index 0000000..73deb4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> @@ -0,0 +1,531 @@
> +/*
> + * Spreadtrum SP9860 SoC DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include "whale2.dtsi"
> +
> +/ {
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> + core1 {
> + cpu = <&CPU1>;
> + };
> + core2 {
> + cpu = <&CPU2>;
> + };
> + core3 {
> + cpu = <&CPU3>;
> + };
> + };
> +
> + cluster1 {
> + core0 {
> + cpu = <&CPU4>;
> + };
> + core1 {
> + cpu = <&CPU5>;
> + };
> + core2 {
> + cpu = <&CPU6>;
> + };
> + core3 {
> + cpu = <&CPU7>;
> + };
> + };
> + };
> +
> + CPU0: cpu@530000 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530000>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU1: cpu@530001 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530001>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU2: cpu@530002 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530002>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU3: cpu@530003 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530003>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU4: cpu@530100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530100>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU5: cpu@530101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530101>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU6: cpu@530102 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530102>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU7: cpu@530103 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530103>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> + };
> +
> + idle-states{
> + entry-method = "arm,psci";
> +
> + CORE_PD: core_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <700>;
> + min-residency-us = <2500>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x00010002>;
> + };
> +
> + CLUSTER_PD: cluster_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <1000>;
> + min-residency-us = <3000>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x01010003>;
> + };
> + };
> +
> + gic: interrupt-controller@12001000 {
> + compatible = "arm,gic-400";
> + reg = <0 0x12001000 0 0x1000>,
> + <0 0x12002000 0 0x2000>,
> + <0 0x12004000 0 0x2000>,
> + <0 0x12006000 0 0x2000>;
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + psci {
> + compatible = "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&CPU0>,
> + <&CPU1>,
> + <&CPU2>,
> + <&CPU3>,
> + <&CPU4>,
> + <&CPU5>,
> + <&CPU6>,
> + <&CPU7>;
> + };
> +
> + soc {
> + soc_funnel: funnel@10001000 {
There is no need for a label ("soc_funnel) before the device name if that
device is not referenced elsewhere in the DTS. The same comment applies to most
of the component listed below.
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x10001000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + soc_funnel_out_port: endpoint {
> + remote-endpoint = <&etb_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + soc_funnel_in_port: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&main_funnel_out_port>;
> + };
> + };
> + };
> + };
> +
> + etb@10003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x10003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + port {
> + etb_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&soc_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster0_funnel: funnel@11001000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11001000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + cluster0_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster0_etf_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + cluster0_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm0_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + cluster0_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm1_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <2>;
> + cluster0_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm2_out>;
> + };
> + };
> +
> + port@4 {
> + reg = <4>;
> + cluster0_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm3_out>;
> + };
> + };
> + };
> + };
> +
> + cluster1_funnel: funnel@11002000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11002000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + cluster1_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster1_etf_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + cluster1_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm4_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + cluster1_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm5_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <2>;
> + cluster1_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm6_out>;
> + };
> + };
> +
> + port@4 {
> + reg = <3>;
> + cluster1_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm7_out>;
> + };
> + };
> + };
> + };
> +
> + cluster0_etf: etf@11003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port@0 {
> + cluster0_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port0>;
> + };
> + };
> +
> + port@1 {
> + cluster0_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster1_etf: etf@11004000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11004000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port@0 {
> + cluster1_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port1>;
> + };
> + };
> +
> + port@1 {
> + cluster1_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_funnel_out_port>;
> + };
> + };
> + };
When more than one port is present it is customary to add another level of
imbrication like it is done for funnels above:
"ports {"
port@0 {
...
port@1 {
...
}
The same comment applies to both etf.
> +
> + main_funnel: funnel@11005000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11005000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + main_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&soc_funnel_in_port>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + main_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_etf_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + main_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_etf_out>;
> + };
> + };
> + };
> + };
> +
> + etm@11440000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11440000 0 0x1000>;
> + cpu = <&CPU0>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm0_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm@11540000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11540000 0 0x1000>;
> + cpu = <&CPU1>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm1_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm@11640000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11640000 0 0x1000>;
> + cpu = <&CPU2>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm2_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm@11740000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11740000 0 0x1000>;
> + cpu = <&CPU3>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm3_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port3>;
> + };
> + };
> + };
> +
> + etm@11840000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11840000 0 0x1000>;
> + cpu = <&CPU4>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm4_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm@11940000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11940000 0 0x1000>;
> + cpu = <&CPU5>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm5_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm@11a40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11a40000 0 0x1000>;
> + cpu = <&CPU6>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm6_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm@11b40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11b40000 0 0x1000>;
> + cpu = <&CPU7>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm7_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port3>;
> + };
> + };
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> new file mode 100644
> index 0000000..5faa452
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> @@ -0,0 +1,56 @@
> +/*
> + * Spreadtrum SP9860g board DTS file
> + *
> + * Copyright (C) 2017, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/dts-v1/;
> +
> +#include "sc9860.dtsi"
> +
> +/ {
> + model = "Spreadtrum SP9860G 3GFHD Board";
> +
> + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> +
> + aliases {
> + serial0 = &uart0; /* for Bluetooth */
> + serial1 = &uart1; /* UART console */
> + serial2 = &uart2; /* Reserved */
> + serial3 = &uart3; /* for GPS */
> + };
> +
> + memory{
> + device_type = "memory";
> + reg = <0x0 0x80000000 0 0x60000000>,
> + <0x1 0x80000000 0 0x60000000>;
> + };
> +
> + chosen {
> + stdout-path = "serial1:115200n8";
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> new file mode 100644
> index 0000000..64f06d9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> @@ -0,0 +1,70 @@
> +/*
> + * Spreadtrum Whale2 SoC platform peripherals DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + soc: soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + ap-apb {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x70000000 0x10000000>;
> +
> + uart0: serial@70000000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x000000 0x100>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart1: serial@70100000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x100000 0x100>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart2: serial@70200000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x200000 0x100>;
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart3: serial@70300000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x300000 0x100>;
> + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> + };
> +
> + ext_26m: ext-26m {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "ext_26m";
> + };
> + };
> +};
> --
> 2.7.4
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-21 16:27 ` Mathieu Poirier
0 siblings, 0 replies; 48+ messages in thread
From: Mathieu Poirier @ 2017-02-21 16:27 UTC (permalink / raw)
To: Chunyan Zhang
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8,
arnd-r2nGTMty4D4, devicetree-u79uwXL29TY76Z2rM5mHXA,
orson.zhai-lxIno14LUO0EEoCn2XhGlw,
zhang.lyra-Re5JQEeQqe8AvxtiuMwx3w,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, sudeep.holla-5wv7dgnIgG8,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Tue, Feb 21, 2017 at 02:55:02PM +0800, Chunyan Zhang wrote:
> From: Orson Zhai <orson.zhai-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
Hello Chunyan,
>
> SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>
> According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> and sp9860g dts is for the board level.
>
> Signed-off-by: Orson Zhai <orson.zhai-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
> Signed-off-by: Chunyan Zhang <chunyan.zhang-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
> ---
> arch/arm64/boot/dts/sprd/Makefile | 3 +-
> arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> 4 files changed, 659 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>
> diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> index b658c5e..f0535e6 100644
> --- a/arch/arm64/boot/dts/sprd/Makefile
> +++ b/arch/arm64/boot/dts/sprd/Makefile
> @@ -1,4 +1,5 @@
> -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> + sp9860g-1h10.dtb
>
> always := $(dtb-y)
> subdir-y := $(dts-dirs)
> diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> new file mode 100644
> index 0000000..73deb4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> @@ -0,0 +1,531 @@
> +/*
> + * Spreadtrum SP9860 SoC DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include "whale2.dtsi"
> +
> +/ {
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> + core1 {
> + cpu = <&CPU1>;
> + };
> + core2 {
> + cpu = <&CPU2>;
> + };
> + core3 {
> + cpu = <&CPU3>;
> + };
> + };
> +
> + cluster1 {
> + core0 {
> + cpu = <&CPU4>;
> + };
> + core1 {
> + cpu = <&CPU5>;
> + };
> + core2 {
> + cpu = <&CPU6>;
> + };
> + core3 {
> + cpu = <&CPU7>;
> + };
> + };
> + };
> +
> + CPU0: cpu@530000 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530000>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU1: cpu@530001 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530001>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU2: cpu@530002 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530002>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU3: cpu@530003 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530003>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU4: cpu@530100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530100>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU5: cpu@530101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530101>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU6: cpu@530102 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530102>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU7: cpu@530103 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530103>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> + };
> +
> + idle-states{
> + entry-method = "arm,psci";
> +
> + CORE_PD: core_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <700>;
> + min-residency-us = <2500>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x00010002>;
> + };
> +
> + CLUSTER_PD: cluster_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <1000>;
> + min-residency-us = <3000>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x01010003>;
> + };
> + };
> +
> + gic: interrupt-controller@12001000 {
> + compatible = "arm,gic-400";
> + reg = <0 0x12001000 0 0x1000>,
> + <0 0x12002000 0 0x2000>,
> + <0 0x12004000 0 0x2000>,
> + <0 0x12006000 0 0x2000>;
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + psci {
> + compatible = "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&CPU0>,
> + <&CPU1>,
> + <&CPU2>,
> + <&CPU3>,
> + <&CPU4>,
> + <&CPU5>,
> + <&CPU6>,
> + <&CPU7>;
> + };
> +
> + soc {
> + soc_funnel: funnel@10001000 {
There is no need for a label ("soc_funnel) before the device name if that
device is not referenced elsewhere in the DTS. The same comment applies to most
of the component listed below.
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x10001000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + soc_funnel_out_port: endpoint {
> + remote-endpoint = <&etb_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + soc_funnel_in_port: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&main_funnel_out_port>;
> + };
> + };
> + };
> + };
> +
> + etb@10003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x10003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + port {
> + etb_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&soc_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster0_funnel: funnel@11001000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11001000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + cluster0_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster0_etf_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + cluster0_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm0_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + cluster0_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm1_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <2>;
> + cluster0_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm2_out>;
> + };
> + };
> +
> + port@4 {
> + reg = <4>;
> + cluster0_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm3_out>;
> + };
> + };
> + };
> + };
> +
> + cluster1_funnel: funnel@11002000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11002000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + cluster1_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster1_etf_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + cluster1_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm4_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + cluster1_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm5_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <2>;
> + cluster1_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm6_out>;
> + };
> + };
> +
> + port@4 {
> + reg = <3>;
> + cluster1_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm7_out>;
> + };
> + };
> + };
> + };
> +
> + cluster0_etf: etf@11003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port@0 {
> + cluster0_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port0>;
> + };
> + };
> +
> + port@1 {
> + cluster0_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster1_etf: etf@11004000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11004000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port@0 {
> + cluster1_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port1>;
> + };
> + };
> +
> + port@1 {
> + cluster1_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_funnel_out_port>;
> + };
> + };
> + };
When more than one port is present it is customary to add another level of
imbrication like it is done for funnels above:
"ports {"
port@0 {
...
port@1 {
...
}
The same comment applies to both etf.
> +
> + main_funnel: funnel@11005000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11005000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + main_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&soc_funnel_in_port>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + main_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_etf_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + main_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_etf_out>;
> + };
> + };
> + };
> + };
> +
> + etm@11440000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11440000 0 0x1000>;
> + cpu = <&CPU0>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm0_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm@11540000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11540000 0 0x1000>;
> + cpu = <&CPU1>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm1_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm@11640000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11640000 0 0x1000>;
> + cpu = <&CPU2>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm2_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm@11740000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11740000 0 0x1000>;
> + cpu = <&CPU3>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm3_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port3>;
> + };
> + };
> + };
> +
> + etm@11840000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11840000 0 0x1000>;
> + cpu = <&CPU4>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm4_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm@11940000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11940000 0 0x1000>;
> + cpu = <&CPU5>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm5_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm@11a40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11a40000 0 0x1000>;
> + cpu = <&CPU6>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm6_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm@11b40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11b40000 0 0x1000>;
> + cpu = <&CPU7>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm7_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port3>;
> + };
> + };
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> new file mode 100644
> index 0000000..5faa452
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> @@ -0,0 +1,56 @@
> +/*
> + * Spreadtrum SP9860g board DTS file
> + *
> + * Copyright (C) 2017, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/dts-v1/;
> +
> +#include "sc9860.dtsi"
> +
> +/ {
> + model = "Spreadtrum SP9860G 3GFHD Board";
> +
> + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> +
> + aliases {
> + serial0 = &uart0; /* for Bluetooth */
> + serial1 = &uart1; /* UART console */
> + serial2 = &uart2; /* Reserved */
> + serial3 = &uart3; /* for GPS */
> + };
> +
> + memory{
> + device_type = "memory";
> + reg = <0x0 0x80000000 0 0x60000000>,
> + <0x1 0x80000000 0 0x60000000>;
> + };
> +
> + chosen {
> + stdout-path = "serial1:115200n8";
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> new file mode 100644
> index 0000000..64f06d9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> @@ -0,0 +1,70 @@
> +/*
> + * Spreadtrum Whale2 SoC platform peripherals DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + soc: soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + ap-apb {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x70000000 0x10000000>;
> +
> + uart0: serial@70000000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x000000 0x100>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart1: serial@70100000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x100000 0x100>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart2: serial@70200000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x200000 0x100>;
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart3: serial@70300000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x300000 0x100>;
> + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> + };
> +
> + ext_26m: ext-26m {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "ext_26m";
> + };
> + };
> +};
> --
> 2.7.4
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-21 16:27 ` Mathieu Poirier
0 siblings, 0 replies; 48+ messages in thread
From: Mathieu Poirier @ 2017-02-21 16:27 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Feb 21, 2017 at 02:55:02PM +0800, Chunyan Zhang wrote:
> From: Orson Zhai <orson.zhai@spreadtrum.com>
Hello Chunyan,
>
> SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>
> According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> and sp9860g dts is for the board level.
>
> Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> ---
> arch/arm64/boot/dts/sprd/Makefile | 3 +-
> arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> 4 files changed, 659 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>
> diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> index b658c5e..f0535e6 100644
> --- a/arch/arm64/boot/dts/sprd/Makefile
> +++ b/arch/arm64/boot/dts/sprd/Makefile
> @@ -1,4 +1,5 @@
> -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> + sp9860g-1h10.dtb
>
> always := $(dtb-y)
> subdir-y := $(dts-dirs)
> diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> new file mode 100644
> index 0000000..73deb4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> @@ -0,0 +1,531 @@
> +/*
> + * Spreadtrum SP9860 SoC DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include "whale2.dtsi"
> +
> +/ {
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> + core1 {
> + cpu = <&CPU1>;
> + };
> + core2 {
> + cpu = <&CPU2>;
> + };
> + core3 {
> + cpu = <&CPU3>;
> + };
> + };
> +
> + cluster1 {
> + core0 {
> + cpu = <&CPU4>;
> + };
> + core1 {
> + cpu = <&CPU5>;
> + };
> + core2 {
> + cpu = <&CPU6>;
> + };
> + core3 {
> + cpu = <&CPU7>;
> + };
> + };
> + };
> +
> + CPU0: cpu at 530000 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530000>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU1: cpu at 530001 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530001>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU2: cpu at 530002 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530002>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU3: cpu at 530003 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530003>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU4: cpu at 530100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530100>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU5: cpu at 530101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530101>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU6: cpu at 530102 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530102>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU7: cpu at 530103 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530103>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> + };
> +
> + idle-states{
> + entry-method = "arm,psci";
> +
> + CORE_PD: core_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <700>;
> + min-residency-us = <2500>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x00010002>;
> + };
> +
> + CLUSTER_PD: cluster_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <1000>;
> + min-residency-us = <3000>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x01010003>;
> + };
> + };
> +
> + gic: interrupt-controller at 12001000 {
> + compatible = "arm,gic-400";
> + reg = <0 0x12001000 0 0x1000>,
> + <0 0x12002000 0 0x2000>,
> + <0 0x12004000 0 0x2000>,
> + <0 0x12006000 0 0x2000>;
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + psci {
> + compatible = "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&CPU0>,
> + <&CPU1>,
> + <&CPU2>,
> + <&CPU3>,
> + <&CPU4>,
> + <&CPU5>,
> + <&CPU6>,
> + <&CPU7>;
> + };
> +
> + soc {
> + soc_funnel: funnel at 10001000 {
There is no need for a label ("soc_funnel) before the device name if that
device is not referenced elsewhere in the DTS. The same comment applies to most
of the component listed below.
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x10001000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + soc_funnel_out_port: endpoint {
> + remote-endpoint = <&etb_in>;
> + };
> + };
> +
> + port at 1 {
> + reg = <0>;
> + soc_funnel_in_port: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&main_funnel_out_port>;
> + };
> + };
> + };
> + };
> +
> + etb at 10003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x10003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + port {
> + etb_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&soc_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster0_funnel: funnel at 11001000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11001000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + cluster0_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster0_etf_in>;
> + };
> + };
> +
> + port at 1 {
> + reg = <0>;
> + cluster0_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm0_out>;
> + };
> + };
> +
> + port at 2 {
> + reg = <1>;
> + cluster0_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm1_out>;
> + };
> + };
> +
> + port at 3 {
> + reg = <2>;
> + cluster0_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm2_out>;
> + };
> + };
> +
> + port at 4 {
> + reg = <4>;
> + cluster0_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm3_out>;
> + };
> + };
> + };
> + };
> +
> + cluster1_funnel: funnel at 11002000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11002000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + cluster1_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster1_etf_in>;
> + };
> + };
> +
> + port at 1 {
> + reg = <0>;
> + cluster1_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm4_out>;
> + };
> + };
> +
> + port at 2 {
> + reg = <1>;
> + cluster1_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm5_out>;
> + };
> + };
> +
> + port at 3 {
> + reg = <2>;
> + cluster1_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm6_out>;
> + };
> + };
> +
> + port at 4 {
> + reg = <3>;
> + cluster1_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm7_out>;
> + };
> + };
> + };
> + };
> +
> + cluster0_etf: etf at 11003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port at 0 {
> + cluster0_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port0>;
> + };
> + };
> +
> + port at 1 {
> + cluster0_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster1_etf: etf at 11004000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11004000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port at 0 {
> + cluster1_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port1>;
> + };
> + };
> +
> + port at 1 {
> + cluster1_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_funnel_out_port>;
> + };
> + };
> + };
When more than one port is present it is customary to add another level of
imbrication like it is done for funnels above:
"ports {"
port at 0 {
...
port at 1 {
...
}
The same comment applies to both etf.
> +
> + main_funnel: funnel at 11005000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11005000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + main_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&soc_funnel_in_port>;
> + };
> + };
> +
> + port at 1 {
> + reg = <0>;
> + main_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_etf_out>;
> + };
> + };
> +
> + port at 2 {
> + reg = <1>;
> + main_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_etf_out>;
> + };
> + };
> + };
> + };
> +
> + etm at 11440000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11440000 0 0x1000>;
> + cpu = <&CPU0>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm0_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm at 11540000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11540000 0 0x1000>;
> + cpu = <&CPU1>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm1_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm at 11640000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11640000 0 0x1000>;
> + cpu = <&CPU2>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm2_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm at 11740000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11740000 0 0x1000>;
> + cpu = <&CPU3>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm3_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port3>;
> + };
> + };
> + };
> +
> + etm at 11840000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11840000 0 0x1000>;
> + cpu = <&CPU4>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm4_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm at 11940000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11940000 0 0x1000>;
> + cpu = <&CPU5>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm5_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm at 11a40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11a40000 0 0x1000>;
> + cpu = <&CPU6>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm6_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm at 11b40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11b40000 0 0x1000>;
> + cpu = <&CPU7>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm7_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port3>;
> + };
> + };
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> new file mode 100644
> index 0000000..5faa452
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> @@ -0,0 +1,56 @@
> +/*
> + * Spreadtrum SP9860g board DTS file
> + *
> + * Copyright (C) 2017, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/dts-v1/;
> +
> +#include "sc9860.dtsi"
> +
> +/ {
> + model = "Spreadtrum SP9860G 3GFHD Board";
> +
> + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> +
> + aliases {
> + serial0 = &uart0; /* for Bluetooth */
> + serial1 = &uart1; /* UART console */
> + serial2 = &uart2; /* Reserved */
> + serial3 = &uart3; /* for GPS */
> + };
> +
> + memory{
> + device_type = "memory";
> + reg = <0x0 0x80000000 0 0x60000000>,
> + <0x1 0x80000000 0 0x60000000>;
> + };
> +
> + chosen {
> + stdout-path = "serial1:115200n8";
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> new file mode 100644
> index 0000000..64f06d9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> @@ -0,0 +1,70 @@
> +/*
> + * Spreadtrum Whale2 SoC platform peripherals DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + soc: soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + ap-apb {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x70000000 0x10000000>;
> +
> + uart0: serial at 70000000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x000000 0x100>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart1: serial at 70100000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x100000 0x100>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart2: serial at 70200000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x200000 0x100>;
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart3: serial at 70300000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x300000 0x100>;
> + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> + };
> +
> + ext_26m: ext-26m {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "ext_26m";
> + };
> + };
> +};
> --
> 2.7.4
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-22 3:46 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-22 3:46 UTC (permalink / raw)
To: Mathieu Poirier
Cc: robh+dt, mark.rutland, gregkh, catalin.marinas, will.deacon,
arnd, devicetree, orson.zhai, zhang.lyra, linux-kernel,
sudeep.holla, linux-arm-kernel
Hello Mathieu,
On 二, 2月 21, 2017 at 09:27:44上午 -0700, Mathieu Poirier wrote:
> On Tue, Feb 21, 2017 at 02:55:02PM +0800, Chunyan Zhang wrote:
> > From: Orson Zhai <orson.zhai@spreadtrum.com>
>
> Hello Chunyan,
>
> >
> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
> >
> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> > and sp9860g dts is for the board level.
> >
> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> > ---
> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> > 4 files changed, 659 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> > index b658c5e..f0535e6 100644
> > --- a/arch/arm64/boot/dts/sprd/Makefile
> > +++ b/arch/arm64/boot/dts/sprd/Makefile
> > @@ -1,4 +1,5 @@
> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> > + sp9860g-1h10.dtb
> >
> > always := $(dtb-y)
> > subdir-y := $(dts-dirs)
> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > new file mode 100644
> > index 0000000..73deb4e
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > @@ -0,0 +1,531 @@
> > +/*
> > + * Spreadtrum SP9860 SoC DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include "whale2.dtsi"
> > +
> > +/ {
> > + cpus {
> > + #address-cells = <2>;
> > + #size-cells = <0>;
> > +
> > + cpu-map {
> > + cluster0 {
> > + core0 {
> > + cpu = <&CPU0>;
> > + };
> > + core1 {
> > + cpu = <&CPU1>;
> > + };
> > + core2 {
> > + cpu = <&CPU2>;
> > + };
> > + core3 {
> > + cpu = <&CPU3>;
> > + };
> > + };
> > +
> > + cluster1 {
> > + core0 {
> > + cpu = <&CPU4>;
> > + };
> > + core1 {
> > + cpu = <&CPU5>;
> > + };
> > + core2 {
> > + cpu = <&CPU6>;
> > + };
> > + core3 {
> > + cpu = <&CPU7>;
> > + };
> > + };
> > + };
> > +
> > + CPU0: cpu@530000 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530000>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU1: cpu@530001 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530001>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU2: cpu@530002 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530002>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU3: cpu@530003 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530003>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU4: cpu@530100 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530100>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU5: cpu@530101 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530101>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU6: cpu@530102 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530102>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU7: cpu@530103 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530103>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > + };
> > +
> > + idle-states{
> > + entry-method = "arm,psci";
> > +
> > + CORE_PD: core_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <700>;
> > + min-residency-us = <2500>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x00010002>;
> > + };
> > +
> > + CLUSTER_PD: cluster_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <1000>;
> > + min-residency-us = <3000>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x01010003>;
> > + };
> > + };
> > +
> > + gic: interrupt-controller@12001000 {
> > + compatible = "arm,gic-400";
> > + reg = <0 0x12001000 0 0x1000>,
> > + <0 0x12002000 0 0x2000>,
> > + <0 0x12004000 0 0x2000>,
> > + <0 0x12006000 0 0x2000>;
> > + #interrupt-cells = <3>;
> > + interrupt-controller;
> > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_HIGH)>;
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-0.2";
> > + method = "smc";
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>;
> > + };
> > +
> > + pmu {
> > + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> > + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-affinity = <&CPU0>,
> > + <&CPU1>,
> > + <&CPU2>,
> > + <&CPU3>,
> > + <&CPU4>,
> > + <&CPU5>,
> > + <&CPU6>,
> > + <&CPU7>;
> > + };
> > +
> > + soc {
> > + soc_funnel: funnel@10001000 {
>
> There is no need for a label ("soc_funnel) before the device name if that
> device is not referenced elsewhere in the DTS. The same comment applies to most
> of the component listed below.
>
OK, I will remove these labels from this DT.
And there's another issue I'd like to discuss with you, do you think which way is better:
1) use class name which can represent this kind of components as device node name in DT, e.g.
funnel@... {
}
replicator@... {
}
etb@... {
}
etf@...
etm@...
stm@...
2) use more descriptive device name for those which are more than one on
a SoC, e.g.
soc-funnel@... {
}
cluster0-funnel@... {
}
cluster1-funnel@... {
}
I noticed Juno use the 2), would you suggest that way?
Thanks,
Chunyan
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x10001000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + soc_funnel_out_port: endpoint {
> > + remote-endpoint = <&etb_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + soc_funnel_in_port: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&main_funnel_out_port>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etb@10003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x10003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + port {
> > + etb_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&soc_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster0_funnel: funnel@11001000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11001000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + cluster0_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster0_etf_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + cluster0_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm0_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + cluster0_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm1_out>;
> > + };
> > + };
> > +
> > + port@3 {
> > + reg = <2>;
> > + cluster0_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm2_out>;
> > + };
> > + };
> > +
> > + port@4 {
> > + reg = <4>;
> > + cluster0_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm3_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster1_funnel: funnel@11002000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11002000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + cluster1_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster1_etf_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + cluster1_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm4_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + cluster1_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm5_out>;
> > + };
> > + };
> > +
> > + port@3 {
> > + reg = <2>;
> > + cluster1_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm6_out>;
> > + };
> > + };
> > +
> > + port@4 {
> > + reg = <3>;
> > + cluster1_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm7_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster0_etf: etf@11003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port@0 {
> > + cluster0_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port0>;
> > + };
> > + };
> > +
> > + port@1 {
> > + cluster0_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster1_etf: etf@11004000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11004000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port@0 {
> > + cluster1_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port1>;
> > + };
> > + };
> > +
> > + port@1 {
> > + cluster1_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_funnel_out_port>;
> > + };
> > + };
> > + };
>
> When more than one port is present it is customary to add another level of
> imbrication like it is done for funnels above:
> "ports {"
> port@0 {
> ...
> port@1 {
> ...
> }
>
> The same comment applies to both etf.
>
OK.
> > +
> > + main_funnel: funnel@11005000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11005000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + main_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&soc_funnel_in_port>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + main_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_etf_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + main_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_etf_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etm@11440000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11440000 0 0x1000>;
> > + cpu = <&CPU0>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm0_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm@11540000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11540000 0 0x1000>;
> > + cpu = <&CPU1>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm1_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm@11640000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11640000 0 0x1000>;
> > + cpu = <&CPU2>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm2_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm@11740000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11740000 0 0x1000>;
> > + cpu = <&CPU3>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm3_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port3>;
> > + };
> > + };
> > + };
> > +
> > + etm@11840000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11840000 0 0x1000>;
> > + cpu = <&CPU4>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm4_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm@11940000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11940000 0 0x1000>;
> > + cpu = <&CPU5>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm5_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm@11a40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11a40000 0 0x1000>;
> > + cpu = <&CPU6>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm6_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm@11b40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11b40000 0 0x1000>;
> > + cpu = <&CPU7>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm7_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port3>;
> > + };
> > + };
> > + };
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > new file mode 100644
> > index 0000000..5faa452
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > @@ -0,0 +1,56 @@
> > +/*
> > + * Spreadtrum SP9860g board DTS file
> > + *
> > + * Copyright (C) 2017, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "sc9860.dtsi"
> > +
> > +/ {
> > + model = "Spreadtrum SP9860G 3GFHD Board";
> > +
> > + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> > +
> > + aliases {
> > + serial0 = &uart0; /* for Bluetooth */
> > + serial1 = &uart1; /* UART console */
> > + serial2 = &uart2; /* Reserved */
> > + serial3 = &uart3; /* for GPS */
> > + };
> > +
> > + memory{
> > + device_type = "memory";
> > + reg = <0x0 0x80000000 0 0x60000000>,
> > + <0x1 0x80000000 0 0x60000000>;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial1:115200n8";
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + status = "okay";
> > +};
> > +
> > +&uart3 {
> > + status = "okay";
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > new file mode 100644
> > index 0000000..64f06d9
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > @@ -0,0 +1,70 @@
> > +/*
> > + * Spreadtrum Whale2 SoC platform peripherals DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/ {
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + soc: soc {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + ap-apb {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0 0x0 0x70000000 0x10000000>;
> > +
> > + uart0: serial@70000000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x000000 0x100>;
> > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart1: serial@70100000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x100000 0x100>;
> > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial@70200000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x200000 0x100>;
> > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart3: serial@70300000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x300000 0x100>;
> > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + ext_26m: ext-26m {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <26000000>;
> > + clock-output-names = "ext_26m";
> > + };
> > + };
> > +};
> > --
> > 2.7.4
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-22 3:46 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-22 3:46 UTC (permalink / raw)
To: Mathieu Poirier
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8,
arnd-r2nGTMty4D4, devicetree-u79uwXL29TY76Z2rM5mHXA,
orson.zhai-lxIno14LUO0EEoCn2XhGlw,
zhang.lyra-Re5JQEeQqe8AvxtiuMwx3w,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, sudeep.holla-5wv7dgnIgG8,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Hello Mathieu,
On 二, 2月 21, 2017 at 09:27:44上午 -0700, Mathieu Poirier wrote:
> On Tue, Feb 21, 2017 at 02:55:02PM +0800, Chunyan Zhang wrote:
> > From: Orson Zhai <orson.zhai-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
>
> Hello Chunyan,
>
> >
> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
> >
> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> > and sp9860g dts is for the board level.
> >
> > Signed-off-by: Orson Zhai <orson.zhai-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
> > Signed-off-by: Chunyan Zhang <chunyan.zhang-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
> > ---
> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> > 4 files changed, 659 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> > index b658c5e..f0535e6 100644
> > --- a/arch/arm64/boot/dts/sprd/Makefile
> > +++ b/arch/arm64/boot/dts/sprd/Makefile
> > @@ -1,4 +1,5 @@
> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> > + sp9860g-1h10.dtb
> >
> > always := $(dtb-y)
> > subdir-y := $(dts-dirs)
> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > new file mode 100644
> > index 0000000..73deb4e
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > @@ -0,0 +1,531 @@
> > +/*
> > + * Spreadtrum SP9860 SoC DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include "whale2.dtsi"
> > +
> > +/ {
> > + cpus {
> > + #address-cells = <2>;
> > + #size-cells = <0>;
> > +
> > + cpu-map {
> > + cluster0 {
> > + core0 {
> > + cpu = <&CPU0>;
> > + };
> > + core1 {
> > + cpu = <&CPU1>;
> > + };
> > + core2 {
> > + cpu = <&CPU2>;
> > + };
> > + core3 {
> > + cpu = <&CPU3>;
> > + };
> > + };
> > +
> > + cluster1 {
> > + core0 {
> > + cpu = <&CPU4>;
> > + };
> > + core1 {
> > + cpu = <&CPU5>;
> > + };
> > + core2 {
> > + cpu = <&CPU6>;
> > + };
> > + core3 {
> > + cpu = <&CPU7>;
> > + };
> > + };
> > + };
> > +
> > + CPU0: cpu@530000 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530000>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU1: cpu@530001 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530001>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU2: cpu@530002 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530002>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU3: cpu@530003 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530003>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU4: cpu@530100 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530100>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU5: cpu@530101 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530101>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU6: cpu@530102 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530102>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU7: cpu@530103 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530103>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > + };
> > +
> > + idle-states{
> > + entry-method = "arm,psci";
> > +
> > + CORE_PD: core_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <700>;
> > + min-residency-us = <2500>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x00010002>;
> > + };
> > +
> > + CLUSTER_PD: cluster_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <1000>;
> > + min-residency-us = <3000>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x01010003>;
> > + };
> > + };
> > +
> > + gic: interrupt-controller@12001000 {
> > + compatible = "arm,gic-400";
> > + reg = <0 0x12001000 0 0x1000>,
> > + <0 0x12002000 0 0x2000>,
> > + <0 0x12004000 0 0x2000>,
> > + <0 0x12006000 0 0x2000>;
> > + #interrupt-cells = <3>;
> > + interrupt-controller;
> > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_HIGH)>;
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-0.2";
> > + method = "smc";
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>;
> > + };
> > +
> > + pmu {
> > + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> > + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-affinity = <&CPU0>,
> > + <&CPU1>,
> > + <&CPU2>,
> > + <&CPU3>,
> > + <&CPU4>,
> > + <&CPU5>,
> > + <&CPU6>,
> > + <&CPU7>;
> > + };
> > +
> > + soc {
> > + soc_funnel: funnel@10001000 {
>
> There is no need for a label ("soc_funnel) before the device name if that
> device is not referenced elsewhere in the DTS. The same comment applies to most
> of the component listed below.
>
OK, I will remove these labels from this DT.
And there's another issue I'd like to discuss with you, do you think which way is better:
1) use class name which can represent this kind of components as device node name in DT, e.g.
funnel@... {
}
replicator@... {
}
etb@... {
}
etf@...
etm@...
stm@...
2) use more descriptive device name for those which are more than one on
a SoC, e.g.
soc-funnel@... {
}
cluster0-funnel@... {
}
cluster1-funnel@... {
}
I noticed Juno use the 2), would you suggest that way?
Thanks,
Chunyan
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x10001000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + soc_funnel_out_port: endpoint {
> > + remote-endpoint = <&etb_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + soc_funnel_in_port: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&main_funnel_out_port>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etb@10003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x10003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + port {
> > + etb_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&soc_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster0_funnel: funnel@11001000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11001000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + cluster0_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster0_etf_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + cluster0_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm0_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + cluster0_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm1_out>;
> > + };
> > + };
> > +
> > + port@3 {
> > + reg = <2>;
> > + cluster0_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm2_out>;
> > + };
> > + };
> > +
> > + port@4 {
> > + reg = <4>;
> > + cluster0_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm3_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster1_funnel: funnel@11002000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11002000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + cluster1_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster1_etf_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + cluster1_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm4_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + cluster1_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm5_out>;
> > + };
> > + };
> > +
> > + port@3 {
> > + reg = <2>;
> > + cluster1_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm6_out>;
> > + };
> > + };
> > +
> > + port@4 {
> > + reg = <3>;
> > + cluster1_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm7_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster0_etf: etf@11003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port@0 {
> > + cluster0_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port0>;
> > + };
> > + };
> > +
> > + port@1 {
> > + cluster0_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster1_etf: etf@11004000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11004000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port@0 {
> > + cluster1_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port1>;
> > + };
> > + };
> > +
> > + port@1 {
> > + cluster1_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_funnel_out_port>;
> > + };
> > + };
> > + };
>
> When more than one port is present it is customary to add another level of
> imbrication like it is done for funnels above:
> "ports {"
> port@0 {
> ...
> port@1 {
> ...
> }
>
> The same comment applies to both etf.
>
OK.
> > +
> > + main_funnel: funnel@11005000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11005000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + main_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&soc_funnel_in_port>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + main_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_etf_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + main_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_etf_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etm@11440000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11440000 0 0x1000>;
> > + cpu = <&CPU0>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm0_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm@11540000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11540000 0 0x1000>;
> > + cpu = <&CPU1>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm1_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm@11640000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11640000 0 0x1000>;
> > + cpu = <&CPU2>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm2_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm@11740000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11740000 0 0x1000>;
> > + cpu = <&CPU3>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm3_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port3>;
> > + };
> > + };
> > + };
> > +
> > + etm@11840000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11840000 0 0x1000>;
> > + cpu = <&CPU4>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm4_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm@11940000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11940000 0 0x1000>;
> > + cpu = <&CPU5>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm5_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm@11a40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11a40000 0 0x1000>;
> > + cpu = <&CPU6>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm6_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm@11b40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11b40000 0 0x1000>;
> > + cpu = <&CPU7>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm7_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port3>;
> > + };
> > + };
> > + };
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > new file mode 100644
> > index 0000000..5faa452
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > @@ -0,0 +1,56 @@
> > +/*
> > + * Spreadtrum SP9860g board DTS file
> > + *
> > + * Copyright (C) 2017, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "sc9860.dtsi"
> > +
> > +/ {
> > + model = "Spreadtrum SP9860G 3GFHD Board";
> > +
> > + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> > +
> > + aliases {
> > + serial0 = &uart0; /* for Bluetooth */
> > + serial1 = &uart1; /* UART console */
> > + serial2 = &uart2; /* Reserved */
> > + serial3 = &uart3; /* for GPS */
> > + };
> > +
> > + memory{
> > + device_type = "memory";
> > + reg = <0x0 0x80000000 0 0x60000000>,
> > + <0x1 0x80000000 0 0x60000000>;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial1:115200n8";
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + status = "okay";
> > +};
> > +
> > +&uart3 {
> > + status = "okay";
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > new file mode 100644
> > index 0000000..64f06d9
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > @@ -0,0 +1,70 @@
> > +/*
> > + * Spreadtrum Whale2 SoC platform peripherals DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/ {
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + soc: soc {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + ap-apb {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0 0x0 0x70000000 0x10000000>;
> > +
> > + uart0: serial@70000000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x000000 0x100>;
> > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart1: serial@70100000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x100000 0x100>;
> > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial@70200000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x200000 0x100>;
> > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart3: serial@70300000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x300000 0x100>;
> > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + ext_26m: ext-26m {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <26000000>;
> > + clock-output-names = "ext_26m";
> > + };
> > + };
> > +};
> > --
> > 2.7.4
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-22 3:46 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-22 3:46 UTC (permalink / raw)
To: linux-arm-kernel
Hello Mathieu,
On ?, 2? 21, 2017 at 09:27:44?? -0700, Mathieu Poirier wrote:
> On Tue, Feb 21, 2017 at 02:55:02PM +0800, Chunyan Zhang wrote:
> > From: Orson Zhai <orson.zhai@spreadtrum.com>
>
> Hello Chunyan,
>
> >
> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
> >
> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> > and sp9860g dts is for the board level.
> >
> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> > ---
> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> > 4 files changed, 659 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> > index b658c5e..f0535e6 100644
> > --- a/arch/arm64/boot/dts/sprd/Makefile
> > +++ b/arch/arm64/boot/dts/sprd/Makefile
> > @@ -1,4 +1,5 @@
> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> > + sp9860g-1h10.dtb
> >
> > always := $(dtb-y)
> > subdir-y := $(dts-dirs)
> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > new file mode 100644
> > index 0000000..73deb4e
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > @@ -0,0 +1,531 @@
> > +/*
> > + * Spreadtrum SP9860 SoC DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include "whale2.dtsi"
> > +
> > +/ {
> > + cpus {
> > + #address-cells = <2>;
> > + #size-cells = <0>;
> > +
> > + cpu-map {
> > + cluster0 {
> > + core0 {
> > + cpu = <&CPU0>;
> > + };
> > + core1 {
> > + cpu = <&CPU1>;
> > + };
> > + core2 {
> > + cpu = <&CPU2>;
> > + };
> > + core3 {
> > + cpu = <&CPU3>;
> > + };
> > + };
> > +
> > + cluster1 {
> > + core0 {
> > + cpu = <&CPU4>;
> > + };
> > + core1 {
> > + cpu = <&CPU5>;
> > + };
> > + core2 {
> > + cpu = <&CPU6>;
> > + };
> > + core3 {
> > + cpu = <&CPU7>;
> > + };
> > + };
> > + };
> > +
> > + CPU0: cpu at 530000 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530000>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU1: cpu at 530001 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530001>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU2: cpu at 530002 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530002>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU3: cpu at 530003 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530003>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU4: cpu at 530100 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530100>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU5: cpu at 530101 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530101>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU6: cpu at 530102 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530102>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU7: cpu at 530103 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530103>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > + };
> > +
> > + idle-states{
> > + entry-method = "arm,psci";
> > +
> > + CORE_PD: core_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <700>;
> > + min-residency-us = <2500>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x00010002>;
> > + };
> > +
> > + CLUSTER_PD: cluster_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <1000>;
> > + min-residency-us = <3000>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x01010003>;
> > + };
> > + };
> > +
> > + gic: interrupt-controller at 12001000 {
> > + compatible = "arm,gic-400";
> > + reg = <0 0x12001000 0 0x1000>,
> > + <0 0x12002000 0 0x2000>,
> > + <0 0x12004000 0 0x2000>,
> > + <0 0x12006000 0 0x2000>;
> > + #interrupt-cells = <3>;
> > + interrupt-controller;
> > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_HIGH)>;
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-0.2";
> > + method = "smc";
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>;
> > + };
> > +
> > + pmu {
> > + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> > + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-affinity = <&CPU0>,
> > + <&CPU1>,
> > + <&CPU2>,
> > + <&CPU3>,
> > + <&CPU4>,
> > + <&CPU5>,
> > + <&CPU6>,
> > + <&CPU7>;
> > + };
> > +
> > + soc {
> > + soc_funnel: funnel at 10001000 {
>
> There is no need for a label ("soc_funnel) before the device name if that
> device is not referenced elsewhere in the DTS. The same comment applies to most
> of the component listed below.
>
OK, I will remove these labels from this DT.
And there's another issue I'd like to discuss with you, do you think which way is better:
1) use class name which can represent this kind of components as device node name in DT, e.g.
funnel at ... {
}
replicator at ... {
}
etb at ... {
}
etf at ...
etm at ...
stm at ...
2) use more descriptive device name for those which are more than one on
a SoC, e.g.
soc-funnel at ... {
}
cluster0-funnel at ... {
}
cluster1-funnel at ... {
}
I noticed Juno use the 2), would you suggest that way?
Thanks,
Chunyan
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x10001000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + soc_funnel_out_port: endpoint {
> > + remote-endpoint = <&etb_in>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + reg = <0>;
> > + soc_funnel_in_port: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&main_funnel_out_port>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etb at 10003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x10003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + port {
> > + etb_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&soc_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster0_funnel: funnel at 11001000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11001000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + cluster0_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster0_etf_in>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + reg = <0>;
> > + cluster0_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm0_out>;
> > + };
> > + };
> > +
> > + port at 2 {
> > + reg = <1>;
> > + cluster0_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm1_out>;
> > + };
> > + };
> > +
> > + port at 3 {
> > + reg = <2>;
> > + cluster0_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm2_out>;
> > + };
> > + };
> > +
> > + port at 4 {
> > + reg = <4>;
> > + cluster0_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm3_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster1_funnel: funnel at 11002000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11002000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + cluster1_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster1_etf_in>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + reg = <0>;
> > + cluster1_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm4_out>;
> > + };
> > + };
> > +
> > + port at 2 {
> > + reg = <1>;
> > + cluster1_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm5_out>;
> > + };
> > + };
> > +
> > + port at 3 {
> > + reg = <2>;
> > + cluster1_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm6_out>;
> > + };
> > + };
> > +
> > + port at 4 {
> > + reg = <3>;
> > + cluster1_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm7_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster0_etf: etf at 11003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port at 0 {
> > + cluster0_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port0>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + cluster0_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster1_etf: etf at 11004000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11004000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port at 0 {
> > + cluster1_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port1>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + cluster1_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_funnel_out_port>;
> > + };
> > + };
> > + };
>
> When more than one port is present it is customary to add another level of
> imbrication like it is done for funnels above:
> "ports {"
> port at 0 {
> ...
> port at 1 {
> ...
> }
>
> The same comment applies to both etf.
>
OK.
> > +
> > + main_funnel: funnel at 11005000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11005000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + main_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&soc_funnel_in_port>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + reg = <0>;
> > + main_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_etf_out>;
> > + };
> > + };
> > +
> > + port at 2 {
> > + reg = <1>;
> > + main_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_etf_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etm at 11440000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11440000 0 0x1000>;
> > + cpu = <&CPU0>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm0_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11540000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11540000 0 0x1000>;
> > + cpu = <&CPU1>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm1_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11640000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11640000 0 0x1000>;
> > + cpu = <&CPU2>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm2_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11740000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11740000 0 0x1000>;
> > + cpu = <&CPU3>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm3_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port3>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11840000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11840000 0 0x1000>;
> > + cpu = <&CPU4>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm4_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11940000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11940000 0 0x1000>;
> > + cpu = <&CPU5>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm5_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11a40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11a40000 0 0x1000>;
> > + cpu = <&CPU6>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm6_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11b40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11b40000 0 0x1000>;
> > + cpu = <&CPU7>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm7_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port3>;
> > + };
> > + };
> > + };
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > new file mode 100644
> > index 0000000..5faa452
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > @@ -0,0 +1,56 @@
> > +/*
> > + * Spreadtrum SP9860g board DTS file
> > + *
> > + * Copyright (C) 2017, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "sc9860.dtsi"
> > +
> > +/ {
> > + model = "Spreadtrum SP9860G 3GFHD Board";
> > +
> > + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> > +
> > + aliases {
> > + serial0 = &uart0; /* for Bluetooth */
> > + serial1 = &uart1; /* UART console */
> > + serial2 = &uart2; /* Reserved */
> > + serial3 = &uart3; /* for GPS */
> > + };
> > +
> > + memory{
> > + device_type = "memory";
> > + reg = <0x0 0x80000000 0 0x60000000>,
> > + <0x1 0x80000000 0 0x60000000>;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial1:115200n8";
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + status = "okay";
> > +};
> > +
> > +&uart3 {
> > + status = "okay";
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > new file mode 100644
> > index 0000000..64f06d9
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > @@ -0,0 +1,70 @@
> > +/*
> > + * Spreadtrum Whale2 SoC platform peripherals DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/ {
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + soc: soc {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + ap-apb {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0 0x0 0x70000000 0x10000000>;
> > +
> > + uart0: serial at 70000000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x000000 0x100>;
> > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart1: serial at 70100000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x100000 0x100>;
> > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial at 70200000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x200000 0x100>;
> > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart3: serial at 70300000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x300000 0x100>;
> > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + ext_26m: ext-26m {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <26000000>;
> > + clock-output-names = "ext_26m";
> > + };
> > + };
> > +};
> > --
> > 2.7.4
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
2017-02-22 3:46 ` Chunyan Zhang
(?)
@ 2017-02-22 16:02 ` Mathieu Poirier
-1 siblings, 0 replies; 48+ messages in thread
From: Mathieu Poirier @ 2017-02-22 16:02 UTC (permalink / raw)
To: Mathieu Poirier, Rob Herring, Mark Rutland, Greg KH,
Catalin Marinas, Will Deacon, Arnd Bergmann, devicetree,
Orson Zhai, Lyra Zhang, linux-kernel, Sudeep Holla,
linux-arm-kernel
On 21 February 2017 at 20:46, Chunyan Zhang
<chunyan.zhang@spreadtrum.com> wrote:
> Hello Mathieu,
>
> On 二, 2月 21, 2017 at 09:27:44上午 -0700, Mathieu Poirier wrote:
>> On Tue, Feb 21, 2017 at 02:55:02PM +0800, Chunyan Zhang wrote:
>> > From: Orson Zhai <orson.zhai@spreadtrum.com>
>>
>> Hello Chunyan,
>>
>> >
>> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>> >
>> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
>> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
>> > and sp9860g dts is for the board level.
>> >
>> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
>> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>> > ---
>> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
>> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
>> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
>> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
>> > 4 files changed, 659 insertions(+), 1 deletion(-)
>> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>> >
>> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
>> > index b658c5e..f0535e6 100644
>> > --- a/arch/arm64/boot/dts/sprd/Makefile
>> > +++ b/arch/arm64/boot/dts/sprd/Makefile
>> > @@ -1,4 +1,5 @@
>> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
>> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
>> > + sp9860g-1h10.dtb
>> >
>> > always := $(dtb-y)
>> > subdir-y := $(dts-dirs)
>> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > new file mode 100644
>> > index 0000000..73deb4e
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > @@ -0,0 +1,531 @@
>> > +/*
>> > + * Spreadtrum SP9860 SoC DTS file
>> > + *
>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>> > + */
>> > +
>> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> > +#include "whale2.dtsi"
>> > +
>> > +/ {
>> > + cpus {
>> > + #address-cells = <2>;
>> > + #size-cells = <0>;
>> > +
>> > + cpu-map {
>> > + cluster0 {
>> > + core0 {
>> > + cpu = <&CPU0>;
>> > + };
>> > + core1 {
>> > + cpu = <&CPU1>;
>> > + };
>> > + core2 {
>> > + cpu = <&CPU2>;
>> > + };
>> > + core3 {
>> > + cpu = <&CPU3>;
>> > + };
>> > + };
>> > +
>> > + cluster1 {
>> > + core0 {
>> > + cpu = <&CPU4>;
>> > + };
>> > + core1 {
>> > + cpu = <&CPU5>;
>> > + };
>> > + core2 {
>> > + cpu = <&CPU6>;
>> > + };
>> > + core3 {
>> > + cpu = <&CPU7>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + CPU0: cpu@530000 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530000>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU1: cpu@530001 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530001>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU2: cpu@530002 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530002>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU3: cpu@530003 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530003>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU4: cpu@530100 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530100>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU5: cpu@530101 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530101>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU6: cpu@530102 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530102>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU7: cpu@530103 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530103>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > + };
>> > +
>> > + idle-states{
>> > + entry-method = "arm,psci";
>> > +
>> > + CORE_PD: core_pd {
>> > + compatible = "arm,idle-state";
>> > + entry-latency-us = <1000>;
>> > + exit-latency-us = <700>;
>> > + min-residency-us = <2500>;
>> > + local-timer-stop;
>> > + arm,psci-suspend-param = <0x00010002>;
>> > + };
>> > +
>> > + CLUSTER_PD: cluster_pd {
>> > + compatible = "arm,idle-state";
>> > + entry-latency-us = <1000>;
>> > + exit-latency-us = <1000>;
>> > + min-residency-us = <3000>;
>> > + local-timer-stop;
>> > + arm,psci-suspend-param = <0x01010003>;
>> > + };
>> > + };
>> > +
>> > + gic: interrupt-controller@12001000 {
>> > + compatible = "arm,gic-400";
>> > + reg = <0 0x12001000 0 0x1000>,
>> > + <0 0x12002000 0 0x2000>,
>> > + <0 0x12004000 0 0x2000>,
>> > + <0 0x12006000 0 0x2000>;
>> > + #interrupt-cells = <3>;
>> > + interrupt-controller;
>> > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_HIGH)>;
>> > + };
>> > +
>> > + psci {
>> > + compatible = "arm,psci-0.2";
>> > + method = "smc";
>> > + };
>> > +
>> > + timer {
>> > + compatible = "arm,armv8-timer";
>> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>;
>> > + };
>> > +
>> > + pmu {
>> > + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
>> > + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
>> > + interrupt-affinity = <&CPU0>,
>> > + <&CPU1>,
>> > + <&CPU2>,
>> > + <&CPU3>,
>> > + <&CPU4>,
>> > + <&CPU5>,
>> > + <&CPU6>,
>> > + <&CPU7>;
>> > + };
>> > +
>> > + soc {
>> > + soc_funnel: funnel@10001000 {
>>
>> There is no need for a label ("soc_funnel) before the device name if that
>> device is not referenced elsewhere in the DTS. The same comment applies to most
>> of the component listed below.
>>
>
> OK, I will remove these labels from this DT.
> And there's another issue I'd like to discuss with you, do you think which way is better:
> 1) use class name which can represent this kind of components as device node name in DT, e.g.
> funnel@... {
>
> }
> replicator@... {
>
> }
> etb@... {
>
> }
> etf@...
> etm@...
> stm@...
>
> 2) use more descriptive device name for those which are more than one on
> a SoC, e.g.
> soc-funnel@... {
>
> }
> cluster0-funnel@... {
>
> }
> cluster1-funnel@... {
>
> }
>
> I noticed Juno use the 2), would you suggest that way?
It is better to describe the HW component themselves rather than where
they are in the topology - the address of the component will make sure
the names are unique. So just the component type (etm, funnel,
replicator, ....) and the address they are located at.
>
> Thanks,
> Chunyan
>
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x10001000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port@0 {
>> > + reg = <0>;
>> > + soc_funnel_out_port: endpoint {
>> > + remote-endpoint = <&etb_in>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + reg = <0>;
>> > + soc_funnel_in_port: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&main_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + etb@10003000 {
>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>> > + reg = <0 0x10003000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + port {
>> > + etb_in: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&soc_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster0_funnel: funnel@11001000 {
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x11001000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port@0 {
>> > + reg = <0>;
>> > + cluster0_funnel_out_port: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_etf_in>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + reg = <0>;
>> > + cluster0_funnel_in_port0: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm0_out>;
>> > + };
>> > + };
>> > +
>> > + port@2 {
>> > + reg = <1>;
>> > + cluster0_funnel_in_port1: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm1_out>;
>> > + };
>> > + };
>> > +
>> > + port@3 {
>> > + reg = <2>;
>> > + cluster0_funnel_in_port2: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm2_out>;
>> > + };
>> > + };
>> > +
>> > + port@4 {
>> > + reg = <4>;
>> > + cluster0_funnel_in_port3: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm3_out>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster1_funnel: funnel@11002000 {
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x11002000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port@0 {
>> > + reg = <0>;
>> > + cluster1_funnel_out_port: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_etf_in>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + reg = <0>;
>> > + cluster1_funnel_in_port0: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm4_out>;
>> > + };
>> > + };
>> > +
>> > + port@2 {
>> > + reg = <1>;
>> > + cluster1_funnel_in_port1: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm5_out>;
>> > + };
>> > + };
>> > +
>> > + port@3 {
>> > + reg = <2>;
>> > + cluster1_funnel_in_port2: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm6_out>;
>> > + };
>> > + };
>> > +
>> > + port@4 {
>> > + reg = <3>;
>> > + cluster1_funnel_in_port3: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm7_out>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster0_etf: etf@11003000 {
>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>> > + reg = <0 0x11003000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port@0 {
>> > + cluster0_etf_out: endpoint {
>> > + remote-endpoint =
>> > + <&main_funnel_in_port0>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + cluster0_etf_in: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster0_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster1_etf: etf@11004000 {
>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>> > + reg = <0 0x11004000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port@0 {
>> > + cluster1_etf_out: endpoint {
>> > + remote-endpoint =
>> > + <&main_funnel_in_port1>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + cluster1_etf_in: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster1_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>>
>> When more than one port is present it is customary to add another level of
>> imbrication like it is done for funnels above:
>> "ports {"
>> port@0 {
>> ...
>> port@1 {
>> ...
>> }
>>
>> The same comment applies to both etf.
>>
>
> OK.
>
>> > +
>> > + main_funnel: funnel@11005000 {
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x11005000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port@0 {
>> > + reg = <0>;
>> > + main_funnel_out_port: endpoint {
>> > + remote-endpoint =
>> > + <&soc_funnel_in_port>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + reg = <0>;
>> > + main_funnel_in_port0: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster0_etf_out>;
>> > + };
>> > + };
>> > +
>> > + port@2 {
>> > + reg = <1>;
>> > + main_funnel_in_port1: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster1_etf_out>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11440000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11440000 0 0x1000>;
>> > + cpu = <&CPU0>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm0_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port0>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11540000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11540000 0 0x1000>;
>> > + cpu = <&CPU1>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm1_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port1>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11640000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11640000 0 0x1000>;
>> > + cpu = <&CPU2>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm2_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port2>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11740000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11740000 0 0x1000>;
>> > + cpu = <&CPU3>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm3_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port3>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11840000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11840000 0 0x1000>;
>> > + cpu = <&CPU4>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm4_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port0>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11940000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11940000 0 0x1000>;
>> > + cpu = <&CPU5>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm5_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port1>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11a40000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11a40000 0 0x1000>;
>> > + cpu = <&CPU6>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm6_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port2>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11b40000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11b40000 0 0x1000>;
>> > + cpu = <&CPU7>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm7_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port3>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +};
>> > diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > new file mode 100644
>> > index 0000000..5faa452
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > @@ -0,0 +1,56 @@
>> > +/*
>> > + * Spreadtrum SP9860g board DTS file
>> > + *
>> > + * Copyright (C) 2017, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>> > + */
>> > +
>> > +/dts-v1/;
>> > +
>> > +#include "sc9860.dtsi"
>> > +
>> > +/ {
>> > + model = "Spreadtrum SP9860G 3GFHD Board";
>> > +
>> > + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
>> > +
>> > + aliases {
>> > + serial0 = &uart0; /* for Bluetooth */
>> > + serial1 = &uart1; /* UART console */
>> > + serial2 = &uart2; /* Reserved */
>> > + serial3 = &uart3; /* for GPS */
>> > + };
>> > +
>> > + memory{
>> > + device_type = "memory";
>> > + reg = <0x0 0x80000000 0 0x60000000>,
>> > + <0x1 0x80000000 0 0x60000000>;
>> > + };
>> > +
>> > + chosen {
>> > + stdout-path = "serial1:115200n8";
>> > + };
>> > +
>> > + reserved-memory {
>> > + #address-cells = <2>;
>> > + #size-cells = <2>;
>> > + ranges;
>> > + };
>> > +};
>> > +
>> > +&uart0 {
>> > + status = "okay";
>> > +};
>> > +
>> > +&uart1 {
>> > + status = "okay";
>> > +};
>> > +
>> > +&uart2 {
>> > + status = "okay";
>> > +};
>> > +
>> > +&uart3 {
>> > + status = "okay";
>> > +};
>> > diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
>> > new file mode 100644
>> > index 0000000..64f06d9
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
>> > @@ -0,0 +1,70 @@
>> > +/*
>> > + * Spreadtrum Whale2 SoC platform peripherals DTS file
>> > + *
>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>> > + */
>> > +
>> > +/ {
>> > + interrupt-parent = <&gic>;
>> > + #address-cells = <2>;
>> > + #size-cells = <2>;
>> > +
>> > + soc: soc {
>> > + compatible = "simple-bus";
>> > + #address-cells = <2>;
>> > + #size-cells = <2>;
>> > + ranges;
>> > +
>> > + ap-apb {
>> > + compatible = "simple-bus";
>> > + #address-cells = <1>;
>> > + #size-cells = <1>;
>> > + ranges = <0 0x0 0x70000000 0x10000000>;
>> > +
>> > + uart0: serial@70000000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x000000 0x100>;
>> > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > +
>> > + uart1: serial@70100000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x100000 0x100>;
>> > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > +
>> > + uart2: serial@70200000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x200000 0x100>;
>> > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > +
>> > + uart3: serial@70300000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x300000 0x100>;
>> > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > + };
>> > +
>> > + ext_26m: ext-26m {
>> > + compatible = "fixed-clock";
>> > + #clock-cells = <0>;
>> > + clock-frequency = <26000000>;
>> > + clock-output-names = "ext_26m";
>> > + };
>> > + };
>> > +};
>> > --
>> > 2.7.4
>> >
>> >
>> > _______________________________________________
>> > linux-arm-kernel mailing list
>> > linux-arm-kernel@lists.infradead.org
>> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-22 16:02 ` Mathieu Poirier
0 siblings, 0 replies; 48+ messages in thread
From: Mathieu Poirier @ 2017-02-22 16:02 UTC (permalink / raw)
To: Mathieu Poirier, Rob Herring, Mark Rutland, Greg KH,
Catalin Marinas, Will Deacon, Arnd Bergmann, devicetree,
Orson Zhai, Lyra Zhang, linux-kernel, Sudeep Holla,
linux-arm-kernel
On 21 February 2017 at 20:46, Chunyan Zhang
<chunyan.zhang@spreadtrum.com> wrote:
> Hello Mathieu,
>
> On 二, 2月 21, 2017 at 09:27:44上午 -0700, Mathieu Poirier wrote:
>> On Tue, Feb 21, 2017 at 02:55:02PM +0800, Chunyan Zhang wrote:
>> > From: Orson Zhai <orson.zhai@spreadtrum.com>
>>
>> Hello Chunyan,
>>
>> >
>> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>> >
>> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
>> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
>> > and sp9860g dts is for the board level.
>> >
>> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
>> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>> > ---
>> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
>> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
>> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
>> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
>> > 4 files changed, 659 insertions(+), 1 deletion(-)
>> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>> >
>> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
>> > index b658c5e..f0535e6 100644
>> > --- a/arch/arm64/boot/dts/sprd/Makefile
>> > +++ b/arch/arm64/boot/dts/sprd/Makefile
>> > @@ -1,4 +1,5 @@
>> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
>> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
>> > + sp9860g-1h10.dtb
>> >
>> > always := $(dtb-y)
>> > subdir-y := $(dts-dirs)
>> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > new file mode 100644
>> > index 0000000..73deb4e
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > @@ -0,0 +1,531 @@
>> > +/*
>> > + * Spreadtrum SP9860 SoC DTS file
>> > + *
>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>> > + */
>> > +
>> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> > +#include "whale2.dtsi"
>> > +
>> > +/ {
>> > + cpus {
>> > + #address-cells = <2>;
>> > + #size-cells = <0>;
>> > +
>> > + cpu-map {
>> > + cluster0 {
>> > + core0 {
>> > + cpu = <&CPU0>;
>> > + };
>> > + core1 {
>> > + cpu = <&CPU1>;
>> > + };
>> > + core2 {
>> > + cpu = <&CPU2>;
>> > + };
>> > + core3 {
>> > + cpu = <&CPU3>;
>> > + };
>> > + };
>> > +
>> > + cluster1 {
>> > + core0 {
>> > + cpu = <&CPU4>;
>> > + };
>> > + core1 {
>> > + cpu = <&CPU5>;
>> > + };
>> > + core2 {
>> > + cpu = <&CPU6>;
>> > + };
>> > + core3 {
>> > + cpu = <&CPU7>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + CPU0: cpu@530000 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530000>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU1: cpu@530001 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530001>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU2: cpu@530002 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530002>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU3: cpu@530003 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530003>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU4: cpu@530100 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530100>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU5: cpu@530101 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530101>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU6: cpu@530102 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530102>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU7: cpu@530103 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530103>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > + };
>> > +
>> > + idle-states{
>> > + entry-method = "arm,psci";
>> > +
>> > + CORE_PD: core_pd {
>> > + compatible = "arm,idle-state";
>> > + entry-latency-us = <1000>;
>> > + exit-latency-us = <700>;
>> > + min-residency-us = <2500>;
>> > + local-timer-stop;
>> > + arm,psci-suspend-param = <0x00010002>;
>> > + };
>> > +
>> > + CLUSTER_PD: cluster_pd {
>> > + compatible = "arm,idle-state";
>> > + entry-latency-us = <1000>;
>> > + exit-latency-us = <1000>;
>> > + min-residency-us = <3000>;
>> > + local-timer-stop;
>> > + arm,psci-suspend-param = <0x01010003>;
>> > + };
>> > + };
>> > +
>> > + gic: interrupt-controller@12001000 {
>> > + compatible = "arm,gic-400";
>> > + reg = <0 0x12001000 0 0x1000>,
>> > + <0 0x12002000 0 0x2000>,
>> > + <0 0x12004000 0 0x2000>,
>> > + <0 0x12006000 0 0x2000>;
>> > + #interrupt-cells = <3>;
>> > + interrupt-controller;
>> > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_HIGH)>;
>> > + };
>> > +
>> > + psci {
>> > + compatible = "arm,psci-0.2";
>> > + method = "smc";
>> > + };
>> > +
>> > + timer {
>> > + compatible = "arm,armv8-timer";
>> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>;
>> > + };
>> > +
>> > + pmu {
>> > + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
>> > + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
>> > + interrupt-affinity = <&CPU0>,
>> > + <&CPU1>,
>> > + <&CPU2>,
>> > + <&CPU3>,
>> > + <&CPU4>,
>> > + <&CPU5>,
>> > + <&CPU6>,
>> > + <&CPU7>;
>> > + };
>> > +
>> > + soc {
>> > + soc_funnel: funnel@10001000 {
>>
>> There is no need for a label ("soc_funnel) before the device name if that
>> device is not referenced elsewhere in the DTS. The same comment applies to most
>> of the component listed below.
>>
>
> OK, I will remove these labels from this DT.
> And there's another issue I'd like to discuss with you, do you think which way is better:
> 1) use class name which can represent this kind of components as device node name in DT, e.g.
> funnel@... {
>
> }
> replicator@... {
>
> }
> etb@... {
>
> }
> etf@...
> etm@...
> stm@...
>
> 2) use more descriptive device name for those which are more than one on
> a SoC, e.g.
> soc-funnel@... {
>
> }
> cluster0-funnel@... {
>
> }
> cluster1-funnel@... {
>
> }
>
> I noticed Juno use the 2), would you suggest that way?
It is better to describe the HW component themselves rather than where
they are in the topology - the address of the component will make sure
the names are unique. So just the component type (etm, funnel,
replicator, ....) and the address they are located at.
>
> Thanks,
> Chunyan
>
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x10001000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port@0 {
>> > + reg = <0>;
>> > + soc_funnel_out_port: endpoint {
>> > + remote-endpoint = <&etb_in>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + reg = <0>;
>> > + soc_funnel_in_port: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&main_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + etb@10003000 {
>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>> > + reg = <0 0x10003000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + port {
>> > + etb_in: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&soc_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster0_funnel: funnel@11001000 {
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x11001000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port@0 {
>> > + reg = <0>;
>> > + cluster0_funnel_out_port: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_etf_in>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + reg = <0>;
>> > + cluster0_funnel_in_port0: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm0_out>;
>> > + };
>> > + };
>> > +
>> > + port@2 {
>> > + reg = <1>;
>> > + cluster0_funnel_in_port1: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm1_out>;
>> > + };
>> > + };
>> > +
>> > + port@3 {
>> > + reg = <2>;
>> > + cluster0_funnel_in_port2: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm2_out>;
>> > + };
>> > + };
>> > +
>> > + port@4 {
>> > + reg = <4>;
>> > + cluster0_funnel_in_port3: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm3_out>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster1_funnel: funnel@11002000 {
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x11002000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port@0 {
>> > + reg = <0>;
>> > + cluster1_funnel_out_port: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_etf_in>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + reg = <0>;
>> > + cluster1_funnel_in_port0: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm4_out>;
>> > + };
>> > + };
>> > +
>> > + port@2 {
>> > + reg = <1>;
>> > + cluster1_funnel_in_port1: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm5_out>;
>> > + };
>> > + };
>> > +
>> > + port@3 {
>> > + reg = <2>;
>> > + cluster1_funnel_in_port2: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm6_out>;
>> > + };
>> > + };
>> > +
>> > + port@4 {
>> > + reg = <3>;
>> > + cluster1_funnel_in_port3: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm7_out>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster0_etf: etf@11003000 {
>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>> > + reg = <0 0x11003000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port@0 {
>> > + cluster0_etf_out: endpoint {
>> > + remote-endpoint =
>> > + <&main_funnel_in_port0>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + cluster0_etf_in: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster0_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster1_etf: etf@11004000 {
>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>> > + reg = <0 0x11004000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port@0 {
>> > + cluster1_etf_out: endpoint {
>> > + remote-endpoint =
>> > + <&main_funnel_in_port1>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + cluster1_etf_in: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster1_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>>
>> When more than one port is present it is customary to add another level of
>> imbrication like it is done for funnels above:
>> "ports {"
>> port@0 {
>> ...
>> port@1 {
>> ...
>> }
>>
>> The same comment applies to both etf.
>>
>
> OK.
>
>> > +
>> > + main_funnel: funnel@11005000 {
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x11005000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port@0 {
>> > + reg = <0>;
>> > + main_funnel_out_port: endpoint {
>> > + remote-endpoint =
>> > + <&soc_funnel_in_port>;
>> > + };
>> > + };
>> > +
>> > + port@1 {
>> > + reg = <0>;
>> > + main_funnel_in_port0: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster0_etf_out>;
>> > + };
>> > + };
>> > +
>> > + port@2 {
>> > + reg = <1>;
>> > + main_funnel_in_port1: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster1_etf_out>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11440000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11440000 0 0x1000>;
>> > + cpu = <&CPU0>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm0_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port0>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11540000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11540000 0 0x1000>;
>> > + cpu = <&CPU1>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm1_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port1>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11640000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11640000 0 0x1000>;
>> > + cpu = <&CPU2>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm2_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port2>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11740000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11740000 0 0x1000>;
>> > + cpu = <&CPU3>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm3_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port3>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11840000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11840000 0 0x1000>;
>> > + cpu = <&CPU4>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm4_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port0>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11940000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11940000 0 0x1000>;
>> > + cpu = <&CPU5>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm5_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port1>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11a40000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11a40000 0 0x1000>;
>> > + cpu = <&CPU6>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm6_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port2>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm@11b40000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11b40000 0 0x1000>;
>> > + cpu = <&CPU7>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm7_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port3>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +};
>> > diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > new file mode 100644
>> > index 0000000..5faa452
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > @@ -0,0 +1,56 @@
>> > +/*
>> > + * Spreadtrum SP9860g board DTS file
>> > + *
>> > + * Copyright (C) 2017, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>> > + */
>> > +
>> > +/dts-v1/;
>> > +
>> > +#include "sc9860.dtsi"
>> > +
>> > +/ {
>> > + model = "Spreadtrum SP9860G 3GFHD Board";
>> > +
>> > + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
>> > +
>> > + aliases {
>> > + serial0 = &uart0; /* for Bluetooth */
>> > + serial1 = &uart1; /* UART console */
>> > + serial2 = &uart2; /* Reserved */
>> > + serial3 = &uart3; /* for GPS */
>> > + };
>> > +
>> > + memory{
>> > + device_type = "memory";
>> > + reg = <0x0 0x80000000 0 0x60000000>,
>> > + <0x1 0x80000000 0 0x60000000>;
>> > + };
>> > +
>> > + chosen {
>> > + stdout-path = "serial1:115200n8";
>> > + };
>> > +
>> > + reserved-memory {
>> > + #address-cells = <2>;
>> > + #size-cells = <2>;
>> > + ranges;
>> > + };
>> > +};
>> > +
>> > +&uart0 {
>> > + status = "okay";
>> > +};
>> > +
>> > +&uart1 {
>> > + status = "okay";
>> > +};
>> > +
>> > +&uart2 {
>> > + status = "okay";
>> > +};
>> > +
>> > +&uart3 {
>> > + status = "okay";
>> > +};
>> > diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
>> > new file mode 100644
>> > index 0000000..64f06d9
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
>> > @@ -0,0 +1,70 @@
>> > +/*
>> > + * Spreadtrum Whale2 SoC platform peripherals DTS file
>> > + *
>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>> > + */
>> > +
>> > +/ {
>> > + interrupt-parent = <&gic>;
>> > + #address-cells = <2>;
>> > + #size-cells = <2>;
>> > +
>> > + soc: soc {
>> > + compatible = "simple-bus";
>> > + #address-cells = <2>;
>> > + #size-cells = <2>;
>> > + ranges;
>> > +
>> > + ap-apb {
>> > + compatible = "simple-bus";
>> > + #address-cells = <1>;
>> > + #size-cells = <1>;
>> > + ranges = <0 0x0 0x70000000 0x10000000>;
>> > +
>> > + uart0: serial@70000000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x000000 0x100>;
>> > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > +
>> > + uart1: serial@70100000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x100000 0x100>;
>> > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > +
>> > + uart2: serial@70200000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x200000 0x100>;
>> > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > +
>> > + uart3: serial@70300000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x300000 0x100>;
>> > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > + };
>> > +
>> > + ext_26m: ext-26m {
>> > + compatible = "fixed-clock";
>> > + #clock-cells = <0>;
>> > + clock-frequency = <26000000>;
>> > + clock-output-names = "ext_26m";
>> > + };
>> > + };
>> > +};
>> > --
>> > 2.7.4
>> >
>> >
>> > _______________________________________________
>> > linux-arm-kernel mailing list
>> > linux-arm-kernel@lists.infradead.org
>> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-22 16:02 ` Mathieu Poirier
0 siblings, 0 replies; 48+ messages in thread
From: Mathieu Poirier @ 2017-02-22 16:02 UTC (permalink / raw)
To: linux-arm-kernel
On 21 February 2017 at 20:46, Chunyan Zhang
<chunyan.zhang@spreadtrum.com> wrote:
> Hello Mathieu,
>
> On ?, 2? 21, 2017 at 09:27:44?? -0700, Mathieu Poirier wrote:
>> On Tue, Feb 21, 2017 at 02:55:02PM +0800, Chunyan Zhang wrote:
>> > From: Orson Zhai <orson.zhai@spreadtrum.com>
>>
>> Hello Chunyan,
>>
>> >
>> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>> >
>> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
>> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
>> > and sp9860g dts is for the board level.
>> >
>> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
>> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>> > ---
>> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
>> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
>> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
>> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
>> > 4 files changed, 659 insertions(+), 1 deletion(-)
>> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>> >
>> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
>> > index b658c5e..f0535e6 100644
>> > --- a/arch/arm64/boot/dts/sprd/Makefile
>> > +++ b/arch/arm64/boot/dts/sprd/Makefile
>> > @@ -1,4 +1,5 @@
>> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
>> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
>> > + sp9860g-1h10.dtb
>> >
>> > always := $(dtb-y)
>> > subdir-y := $(dts-dirs)
>> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > new file mode 100644
>> > index 0000000..73deb4e
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > @@ -0,0 +1,531 @@
>> > +/*
>> > + * Spreadtrum SP9860 SoC DTS file
>> > + *
>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>> > + */
>> > +
>> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> > +#include "whale2.dtsi"
>> > +
>> > +/ {
>> > + cpus {
>> > + #address-cells = <2>;
>> > + #size-cells = <0>;
>> > +
>> > + cpu-map {
>> > + cluster0 {
>> > + core0 {
>> > + cpu = <&CPU0>;
>> > + };
>> > + core1 {
>> > + cpu = <&CPU1>;
>> > + };
>> > + core2 {
>> > + cpu = <&CPU2>;
>> > + };
>> > + core3 {
>> > + cpu = <&CPU3>;
>> > + };
>> > + };
>> > +
>> > + cluster1 {
>> > + core0 {
>> > + cpu = <&CPU4>;
>> > + };
>> > + core1 {
>> > + cpu = <&CPU5>;
>> > + };
>> > + core2 {
>> > + cpu = <&CPU6>;
>> > + };
>> > + core3 {
>> > + cpu = <&CPU7>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + CPU0: cpu at 530000 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530000>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU1: cpu at 530001 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530001>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU2: cpu at 530002 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530002>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU3: cpu at 530003 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530003>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU4: cpu at 530100 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530100>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU5: cpu at 530101 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530101>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU6: cpu at 530102 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530102>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > +
>> > + CPU7: cpu at 530103 {
>> > + device_type = "cpu";
>> > + compatible = "arm,cortex-a53", "arm,armv8";
>> > + reg = <0x0 0x530103>;
>> > + enable-method = "psci";
>> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
>> > + };
>> > + };
>> > +
>> > + idle-states{
>> > + entry-method = "arm,psci";
>> > +
>> > + CORE_PD: core_pd {
>> > + compatible = "arm,idle-state";
>> > + entry-latency-us = <1000>;
>> > + exit-latency-us = <700>;
>> > + min-residency-us = <2500>;
>> > + local-timer-stop;
>> > + arm,psci-suspend-param = <0x00010002>;
>> > + };
>> > +
>> > + CLUSTER_PD: cluster_pd {
>> > + compatible = "arm,idle-state";
>> > + entry-latency-us = <1000>;
>> > + exit-latency-us = <1000>;
>> > + min-residency-us = <3000>;
>> > + local-timer-stop;
>> > + arm,psci-suspend-param = <0x01010003>;
>> > + };
>> > + };
>> > +
>> > + gic: interrupt-controller at 12001000 {
>> > + compatible = "arm,gic-400";
>> > + reg = <0 0x12001000 0 0x1000>,
>> > + <0 0x12002000 0 0x2000>,
>> > + <0 0x12004000 0 0x2000>,
>> > + <0 0x12006000 0 0x2000>;
>> > + #interrupt-cells = <3>;
>> > + interrupt-controller;
>> > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_HIGH)>;
>> > + };
>> > +
>> > + psci {
>> > + compatible = "arm,psci-0.2";
>> > + method = "smc";
>> > + };
>> > +
>> > + timer {
>> > + compatible = "arm,armv8-timer";
>> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>,
>> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
>> > + | IRQ_TYPE_LEVEL_LOW)>;
>> > + };
>> > +
>> > + pmu {
>> > + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
>> > + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
>> > + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
>> > + interrupt-affinity = <&CPU0>,
>> > + <&CPU1>,
>> > + <&CPU2>,
>> > + <&CPU3>,
>> > + <&CPU4>,
>> > + <&CPU5>,
>> > + <&CPU6>,
>> > + <&CPU7>;
>> > + };
>> > +
>> > + soc {
>> > + soc_funnel: funnel at 10001000 {
>>
>> There is no need for a label ("soc_funnel) before the device name if that
>> device is not referenced elsewhere in the DTS. The same comment applies to most
>> of the component listed below.
>>
>
> OK, I will remove these labels from this DT.
> And there's another issue I'd like to discuss with you, do you think which way is better:
> 1) use class name which can represent this kind of components as device node name in DT, e.g.
> funnel at ... {
>
> }
> replicator at ... {
>
> }
> etb at ... {
>
> }
> etf at ...
> etm at ...
> stm at ...
>
> 2) use more descriptive device name for those which are more than one on
> a SoC, e.g.
> soc-funnel at ... {
>
> }
> cluster0-funnel at ... {
>
> }
> cluster1-funnel at ... {
>
> }
>
> I noticed Juno use the 2), would you suggest that way?
It is better to describe the HW component themselves rather than where
they are in the topology - the address of the component will make sure
the names are unique. So just the component type (etm, funnel,
replicator, ....) and the address they are located at.
>
> Thanks,
> Chunyan
>
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x10001000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port at 0 {
>> > + reg = <0>;
>> > + soc_funnel_out_port: endpoint {
>> > + remote-endpoint = <&etb_in>;
>> > + };
>> > + };
>> > +
>> > + port at 1 {
>> > + reg = <0>;
>> > + soc_funnel_in_port: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&main_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + etb at 10003000 {
>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>> > + reg = <0 0x10003000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + port {
>> > + etb_in: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&soc_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster0_funnel: funnel at 11001000 {
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x11001000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port at 0 {
>> > + reg = <0>;
>> > + cluster0_funnel_out_port: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_etf_in>;
>> > + };
>> > + };
>> > +
>> > + port at 1 {
>> > + reg = <0>;
>> > + cluster0_funnel_in_port0: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm0_out>;
>> > + };
>> > + };
>> > +
>> > + port at 2 {
>> > + reg = <1>;
>> > + cluster0_funnel_in_port1: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm1_out>;
>> > + };
>> > + };
>> > +
>> > + port at 3 {
>> > + reg = <2>;
>> > + cluster0_funnel_in_port2: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm2_out>;
>> > + };
>> > + };
>> > +
>> > + port at 4 {
>> > + reg = <4>;
>> > + cluster0_funnel_in_port3: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm3_out>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster1_funnel: funnel at 11002000 {
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x11002000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port at 0 {
>> > + reg = <0>;
>> > + cluster1_funnel_out_port: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_etf_in>;
>> > + };
>> > + };
>> > +
>> > + port at 1 {
>> > + reg = <0>;
>> > + cluster1_funnel_in_port0: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm4_out>;
>> > + };
>> > + };
>> > +
>> > + port at 2 {
>> > + reg = <1>;
>> > + cluster1_funnel_in_port1: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm5_out>;
>> > + };
>> > + };
>> > +
>> > + port at 3 {
>> > + reg = <2>;
>> > + cluster1_funnel_in_port2: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm6_out>;
>> > + };
>> > + };
>> > +
>> > + port at 4 {
>> > + reg = <3>;
>> > + cluster1_funnel_in_port3: endpoint {
>> > + slave-mode;
>> > + remote-endpoint = <&etm7_out>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster0_etf: etf at 11003000 {
>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>> > + reg = <0 0x11003000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port at 0 {
>> > + cluster0_etf_out: endpoint {
>> > + remote-endpoint =
>> > + <&main_funnel_in_port0>;
>> > + };
>> > + };
>> > +
>> > + port at 1 {
>> > + cluster0_etf_in: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster0_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + cluster1_etf: etf at 11004000 {
>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>> > + reg = <0 0x11004000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port at 0 {
>> > + cluster1_etf_out: endpoint {
>> > + remote-endpoint =
>> > + <&main_funnel_in_port1>;
>> > + };
>> > + };
>> > +
>> > + port at 1 {
>> > + cluster1_etf_in: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster1_funnel_out_port>;
>> > + };
>> > + };
>> > + };
>>
>> When more than one port is present it is customary to add another level of
>> imbrication like it is done for funnels above:
>> "ports {"
>> port at 0 {
>> ...
>> port at 1 {
>> ...
>> }
>>
>> The same comment applies to both etf.
>>
>
> OK.
>
>> > +
>> > + main_funnel: funnel at 11005000 {
>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>> > + reg = <0 0x11005000 0 0x1000>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + ports {
>> > + #address-cells = <1>;
>> > + #size-cells = <0>;
>> > +
>> > + port at 0 {
>> > + reg = <0>;
>> > + main_funnel_out_port: endpoint {
>> > + remote-endpoint =
>> > + <&soc_funnel_in_port>;
>> > + };
>> > + };
>> > +
>> > + port at 1 {
>> > + reg = <0>;
>> > + main_funnel_in_port0: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster0_etf_out>;
>> > + };
>> > + };
>> > +
>> > + port at 2 {
>> > + reg = <1>;
>> > + main_funnel_in_port1: endpoint {
>> > + slave-mode;
>> > + remote-endpoint =
>> > + <&cluster1_etf_out>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm at 11440000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11440000 0 0x1000>;
>> > + cpu = <&CPU0>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm0_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port0>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm at 11540000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11540000 0 0x1000>;
>> > + cpu = <&CPU1>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm1_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port1>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm at 11640000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11640000 0 0x1000>;
>> > + cpu = <&CPU2>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm2_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port2>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm at 11740000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11740000 0 0x1000>;
>> > + cpu = <&CPU3>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm3_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster0_funnel_in_port3>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm at 11840000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11840000 0 0x1000>;
>> > + cpu = <&CPU4>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm4_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port0>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm at 11940000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11940000 0 0x1000>;
>> > + cpu = <&CPU5>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm5_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port1>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm at 11a40000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11a40000 0 0x1000>;
>> > + cpu = <&CPU6>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm6_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port2>;
>> > + };
>> > + };
>> > + };
>> > +
>> > + etm at 11b40000 {
>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>> > + reg = <0 0x11b40000 0 0x1000>;
>> > + cpu = <&CPU7>;
>> > + clocks = <&ext_26m>;
>> > + clock-names = "apb_pclk";
>> > +
>> > + port {
>> > + etm7_out: endpoint {
>> > + remote-endpoint =
>> > + <&cluster1_funnel_in_port3>;
>> > + };
>> > + };
>> > + };
>> > + };
>> > +};
>> > diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > new file mode 100644
>> > index 0000000..5faa452
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > @@ -0,0 +1,56 @@
>> > +/*
>> > + * Spreadtrum SP9860g board DTS file
>> > + *
>> > + * Copyright (C) 2017, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>> > + */
>> > +
>> > +/dts-v1/;
>> > +
>> > +#include "sc9860.dtsi"
>> > +
>> > +/ {
>> > + model = "Spreadtrum SP9860G 3GFHD Board";
>> > +
>> > + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
>> > +
>> > + aliases {
>> > + serial0 = &uart0; /* for Bluetooth */
>> > + serial1 = &uart1; /* UART console */
>> > + serial2 = &uart2; /* Reserved */
>> > + serial3 = &uart3; /* for GPS */
>> > + };
>> > +
>> > + memory{
>> > + device_type = "memory";
>> > + reg = <0x0 0x80000000 0 0x60000000>,
>> > + <0x1 0x80000000 0 0x60000000>;
>> > + };
>> > +
>> > + chosen {
>> > + stdout-path = "serial1:115200n8";
>> > + };
>> > +
>> > + reserved-memory {
>> > + #address-cells = <2>;
>> > + #size-cells = <2>;
>> > + ranges;
>> > + };
>> > +};
>> > +
>> > +&uart0 {
>> > + status = "okay";
>> > +};
>> > +
>> > +&uart1 {
>> > + status = "okay";
>> > +};
>> > +
>> > +&uart2 {
>> > + status = "okay";
>> > +};
>> > +
>> > +&uart3 {
>> > + status = "okay";
>> > +};
>> > diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
>> > new file mode 100644
>> > index 0000000..64f06d9
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
>> > @@ -0,0 +1,70 @@
>> > +/*
>> > + * Spreadtrum Whale2 SoC platform peripherals DTS file
>> > + *
>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>> > + */
>> > +
>> > +/ {
>> > + interrupt-parent = <&gic>;
>> > + #address-cells = <2>;
>> > + #size-cells = <2>;
>> > +
>> > + soc: soc {
>> > + compatible = "simple-bus";
>> > + #address-cells = <2>;
>> > + #size-cells = <2>;
>> > + ranges;
>> > +
>> > + ap-apb {
>> > + compatible = "simple-bus";
>> > + #address-cells = <1>;
>> > + #size-cells = <1>;
>> > + ranges = <0 0x0 0x70000000 0x10000000>;
>> > +
>> > + uart0: serial at 70000000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x000000 0x100>;
>> > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > +
>> > + uart1: serial at 70100000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x100000 0x100>;
>> > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > +
>> > + uart2: serial at 70200000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x200000 0x100>;
>> > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > +
>> > + uart3: serial at 70300000 {
>> > + compatible = "sprd,sc9838-uart",
>> > + "sprd,sc9836-uart";
>> > + reg = <0x300000 0x100>;
>> > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
>> > + clocks = <&ext_26m>;
>> > + status = "disabled";
>> > + };
>> > + };
>> > +
>> > + ext_26m: ext-26m {
>> > + compatible = "fixed-clock";
>> > + #clock-cells = <0>;
>> > + clock-frequency = <26000000>;
>> > + clock-output-names = "ext_26m";
>> > + };
>> > + };
>> > +};
>> > --
>> > 2.7.4
>> >
>> >
>> > _______________________________________________
>> > linux-arm-kernel mailing list
>> > linux-arm-kernel at lists.infradead.org
>> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
2017-02-22 16:02 ` Mathieu Poirier
(?)
@ 2017-02-23 6:20 ` Chunyan Zhang
-1 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-23 6:20 UTC (permalink / raw)
To: Mathieu Poirier
Cc: Rob Herring, Mark Rutland, Greg KH, Catalin Marinas, Will Deacon,
Arnd Bergmann, devicetree, Orson Zhai, linux-kernel,
Sudeep Holla, linux-arm-kernel
[...]
>>> > +
>>> > + soc {
>>> > + soc_funnel: funnel@10001000 {
>>>
>>> There is no need for a label ("soc_funnel) before the device name if that
>>> device is not referenced elsewhere in the DTS. The same comment applies to most
>>> of the component listed below.
>>>
>>
>> OK, I will remove these labels from this DT.
>> And there's another issue I'd like to discuss with you, do you think which way is better:
>> 1) use class name which can represent this kind of components as device node name in DT, e.g.
>> funnel@... {
>>
>> }
>> replicator@... {
>>
>> }
>> etb@... {
>>
>> }
>> etf@...
>> etm@...
>> stm@...
>>
>> 2) use more descriptive device name for those which are more than one on
>> a SoC, e.g.
>> soc-funnel@... {
>>
>> }
>> cluster0-funnel@... {
>>
>> }
>> cluster1-funnel@... {
>>
>> }
>>
>> I noticed Juno use the 2), would you suggest that way?
>
> It is better to describe the HW component themselves rather than where
> they are in the topology - the address of the component will make sure
> the names are unique. So just the component type (etm, funnel,
> replicator, ....) and the address they are located at.
>
OK. And to avoid making other person confused in the future, is it
better to revise juno-base.dtsi according to this convention?
Thanks,
Chunyan
>>
>> Thanks,
>> Chunyan
>>
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x10001000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port@0 {
>>> > + reg = <0>;
>>> > + soc_funnel_out_port: endpoint {
>>> > + remote-endpoint = <&etb_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + reg = <0>;
>>> > + soc_funnel_in_port: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&main_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etb@10003000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x10003000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + port {
>>> > + etb_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&soc_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster0_funnel: funnel@11001000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11001000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port@0 {
>>> > + reg = <0>;
>>> > + cluster0_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_etf_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + reg = <0>;
>>> > + cluster0_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm0_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@2 {
>>> > + reg = <1>;
>>> > + cluster0_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm1_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@3 {
>>> > + reg = <2>;
>>> > + cluster0_funnel_in_port2: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm2_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@4 {
>>> > + reg = <4>;
>>> > + cluster0_funnel_in_port3: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm3_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster1_funnel: funnel@11002000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11002000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port@0 {
>>> > + reg = <0>;
>>> > + cluster1_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_etf_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + reg = <0>;
>>> > + cluster1_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm4_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@2 {
>>> > + reg = <1>;
>>> > + cluster1_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm5_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@3 {
>>> > + reg = <2>;
>>> > + cluster1_funnel_in_port2: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm6_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@4 {
>>> > + reg = <3>;
>>> > + cluster1_funnel_in_port3: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm7_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster0_etf: etf@11003000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x11003000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port@0 {
>>> > + cluster0_etf_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&main_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + cluster0_etf_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster1_etf: etf@11004000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x11004000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port@0 {
>>> > + cluster1_etf_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&main_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + cluster1_etf_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>>
>>> When more than one port is present it is customary to add another level of
>>> imbrication like it is done for funnels above:
>>> "ports {"
>>> port@0 {
>>> ...
>>> port@1 {
>>> ...
>>> }
>>>
>>> The same comment applies to both etf.
>>>
>>
>> OK.
>>
>>> > +
>>> > + main_funnel: funnel@11005000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11005000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port@0 {
>>> > + reg = <0>;
>>> > + main_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&soc_funnel_in_port>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + reg = <0>;
>>> > + main_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster0_etf_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@2 {
>>> > + reg = <1>;
>>> > + main_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster1_etf_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11440000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11440000 0 0x1000>;
>>> > + cpu = <&CPU0>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm0_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11540000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11540000 0 0x1000>;
>>> > + cpu = <&CPU1>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm1_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11640000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11640000 0 0x1000>;
>>> > + cpu = <&CPU2>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm2_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port2>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11740000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11740000 0 0x1000>;
>>> > + cpu = <&CPU3>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm3_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port3>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11840000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11840000 0 0x1000>;
>>> > + cpu = <&CPU4>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm4_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11940000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11940000 0 0x1000>;
>>> > + cpu = <&CPU5>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm5_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11a40000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11a40000 0 0x1000>;
>>> > + cpu = <&CPU6>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm6_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port2>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11b40000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11b40000 0 0x1000>;
>>> > + cpu = <&CPU7>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm7_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port3>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +};
[...]
>>> >
>>> > _______________________________________________
>>> > linux-arm-kernel mailing list
>>> > linux-arm-kernel@lists.infradead.org
>>> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>> --
>> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-23 6:20 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-23 6:20 UTC (permalink / raw)
To: Mathieu Poirier
Cc: Mark Rutland, devicetree, Orson Zhai, Arnd Bergmann, Greg KH,
Sudeep Holla, Will Deacon, linux-kernel, Rob Herring,
Catalin Marinas, linux-arm-kernel
[...]
>>> > +
>>> > + soc {
>>> > + soc_funnel: funnel@10001000 {
>>>
>>> There is no need for a label ("soc_funnel) before the device name if that
>>> device is not referenced elsewhere in the DTS. The same comment applies to most
>>> of the component listed below.
>>>
>>
>> OK, I will remove these labels from this DT.
>> And there's another issue I'd like to discuss with you, do you think which way is better:
>> 1) use class name which can represent this kind of components as device node name in DT, e.g.
>> funnel@... {
>>
>> }
>> replicator@... {
>>
>> }
>> etb@... {
>>
>> }
>> etf@...
>> etm@...
>> stm@...
>>
>> 2) use more descriptive device name for those which are more than one on
>> a SoC, e.g.
>> soc-funnel@... {
>>
>> }
>> cluster0-funnel@... {
>>
>> }
>> cluster1-funnel@... {
>>
>> }
>>
>> I noticed Juno use the 2), would you suggest that way?
>
> It is better to describe the HW component themselves rather than where
> they are in the topology - the address of the component will make sure
> the names are unique. So just the component type (etm, funnel,
> replicator, ....) and the address they are located at.
>
OK. And to avoid making other person confused in the future, is it
better to revise juno-base.dtsi according to this convention?
Thanks,
Chunyan
>>
>> Thanks,
>> Chunyan
>>
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x10001000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port@0 {
>>> > + reg = <0>;
>>> > + soc_funnel_out_port: endpoint {
>>> > + remote-endpoint = <&etb_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + reg = <0>;
>>> > + soc_funnel_in_port: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&main_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etb@10003000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x10003000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + port {
>>> > + etb_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&soc_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster0_funnel: funnel@11001000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11001000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port@0 {
>>> > + reg = <0>;
>>> > + cluster0_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_etf_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + reg = <0>;
>>> > + cluster0_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm0_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@2 {
>>> > + reg = <1>;
>>> > + cluster0_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm1_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@3 {
>>> > + reg = <2>;
>>> > + cluster0_funnel_in_port2: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm2_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@4 {
>>> > + reg = <4>;
>>> > + cluster0_funnel_in_port3: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm3_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster1_funnel: funnel@11002000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11002000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port@0 {
>>> > + reg = <0>;
>>> > + cluster1_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_etf_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + reg = <0>;
>>> > + cluster1_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm4_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@2 {
>>> > + reg = <1>;
>>> > + cluster1_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm5_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@3 {
>>> > + reg = <2>;
>>> > + cluster1_funnel_in_port2: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm6_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@4 {
>>> > + reg = <3>;
>>> > + cluster1_funnel_in_port3: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm7_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster0_etf: etf@11003000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x11003000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port@0 {
>>> > + cluster0_etf_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&main_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + cluster0_etf_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster1_etf: etf@11004000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x11004000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port@0 {
>>> > + cluster1_etf_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&main_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + cluster1_etf_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>>
>>> When more than one port is present it is customary to add another level of
>>> imbrication like it is done for funnels above:
>>> "ports {"
>>> port@0 {
>>> ...
>>> port@1 {
>>> ...
>>> }
>>>
>>> The same comment applies to both etf.
>>>
>>
>> OK.
>>
>>> > +
>>> > + main_funnel: funnel@11005000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11005000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port@0 {
>>> > + reg = <0>;
>>> > + main_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&soc_funnel_in_port>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@1 {
>>> > + reg = <0>;
>>> > + main_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster0_etf_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port@2 {
>>> > + reg = <1>;
>>> > + main_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster1_etf_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11440000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11440000 0 0x1000>;
>>> > + cpu = <&CPU0>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm0_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11540000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11540000 0 0x1000>;
>>> > + cpu = <&CPU1>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm1_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11640000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11640000 0 0x1000>;
>>> > + cpu = <&CPU2>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm2_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port2>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11740000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11740000 0 0x1000>;
>>> > + cpu = <&CPU3>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm3_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port3>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11840000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11840000 0 0x1000>;
>>> > + cpu = <&CPU4>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm4_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11940000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11940000 0 0x1000>;
>>> > + cpu = <&CPU5>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm5_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11a40000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11a40000 0 0x1000>;
>>> > + cpu = <&CPU6>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm6_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port2>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm@11b40000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11b40000 0 0x1000>;
>>> > + cpu = <&CPU7>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm7_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port3>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +};
[...]
>>> >
>>> > _______________________________________________
>>> > linux-arm-kernel mailing list
>>> > linux-arm-kernel@lists.infradead.org
>>> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>> --
>> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-23 6:20 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-23 6:20 UTC (permalink / raw)
To: linux-arm-kernel
[...]
>>> > +
>>> > + soc {
>>> > + soc_funnel: funnel at 10001000 {
>>>
>>> There is no need for a label ("soc_funnel) before the device name if that
>>> device is not referenced elsewhere in the DTS. The same comment applies to most
>>> of the component listed below.
>>>
>>
>> OK, I will remove these labels from this DT.
>> And there's another issue I'd like to discuss with you, do you think which way is better:
>> 1) use class name which can represent this kind of components as device node name in DT, e.g.
>> funnel at ... {
>>
>> }
>> replicator at ... {
>>
>> }
>> etb at ... {
>>
>> }
>> etf at ...
>> etm at ...
>> stm at ...
>>
>> 2) use more descriptive device name for those which are more than one on
>> a SoC, e.g.
>> soc-funnel at ... {
>>
>> }
>> cluster0-funnel at ... {
>>
>> }
>> cluster1-funnel at ... {
>>
>> }
>>
>> I noticed Juno use the 2), would you suggest that way?
>
> It is better to describe the HW component themselves rather than where
> they are in the topology - the address of the component will make sure
> the names are unique. So just the component type (etm, funnel,
> replicator, ....) and the address they are located at.
>
OK. And to avoid making other person confused in the future, is it
better to revise juno-base.dtsi according to this convention?
Thanks,
Chunyan
>>
>> Thanks,
>> Chunyan
>>
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x10001000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port at 0 {
>>> > + reg = <0>;
>>> > + soc_funnel_out_port: endpoint {
>>> > + remote-endpoint = <&etb_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + reg = <0>;
>>> > + soc_funnel_in_port: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&main_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etb at 10003000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x10003000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + port {
>>> > + etb_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&soc_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster0_funnel: funnel at 11001000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11001000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port at 0 {
>>> > + reg = <0>;
>>> > + cluster0_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_etf_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + reg = <0>;
>>> > + cluster0_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm0_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 2 {
>>> > + reg = <1>;
>>> > + cluster0_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm1_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 3 {
>>> > + reg = <2>;
>>> > + cluster0_funnel_in_port2: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm2_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 4 {
>>> > + reg = <4>;
>>> > + cluster0_funnel_in_port3: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm3_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster1_funnel: funnel at 11002000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11002000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port at 0 {
>>> > + reg = <0>;
>>> > + cluster1_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_etf_in>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + reg = <0>;
>>> > + cluster1_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm4_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 2 {
>>> > + reg = <1>;
>>> > + cluster1_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm5_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 3 {
>>> > + reg = <2>;
>>> > + cluster1_funnel_in_port2: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm6_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 4 {
>>> > + reg = <3>;
>>> > + cluster1_funnel_in_port3: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint = <&etm7_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster0_etf: etf at 11003000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x11003000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port at 0 {
>>> > + cluster0_etf_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&main_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + cluster0_etf_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + cluster1_etf: etf at 11004000 {
>>> > + compatible = "arm,coresight-tmc", "arm,primecell";
>>> > + reg = <0 0x11004000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port at 0 {
>>> > + cluster1_etf_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&main_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + cluster1_etf_in: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_out_port>;
>>> > + };
>>> > + };
>>> > + };
>>>
>>> When more than one port is present it is customary to add another level of
>>> imbrication like it is done for funnels above:
>>> "ports {"
>>> port at 0 {
>>> ...
>>> port at 1 {
>>> ...
>>> }
>>>
>>> The same comment applies to both etf.
>>>
>>
>> OK.
>>
>>> > +
>>> > + main_funnel: funnel at 11005000 {
>>> > + compatible = "arm,coresight-funnel", "arm,primecell";
>>> > + reg = <0 0x11005000 0 0x1000>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + ports {
>>> > + #address-cells = <1>;
>>> > + #size-cells = <0>;
>>> > +
>>> > + port at 0 {
>>> > + reg = <0>;
>>> > + main_funnel_out_port: endpoint {
>>> > + remote-endpoint =
>>> > + <&soc_funnel_in_port>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 1 {
>>> > + reg = <0>;
>>> > + main_funnel_in_port0: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster0_etf_out>;
>>> > + };
>>> > + };
>>> > +
>>> > + port at 2 {
>>> > + reg = <1>;
>>> > + main_funnel_in_port1: endpoint {
>>> > + slave-mode;
>>> > + remote-endpoint =
>>> > + <&cluster1_etf_out>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11440000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11440000 0 0x1000>;
>>> > + cpu = <&CPU0>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm0_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11540000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11540000 0 0x1000>;
>>> > + cpu = <&CPU1>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm1_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11640000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11640000 0 0x1000>;
>>> > + cpu = <&CPU2>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm2_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port2>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11740000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11740000 0 0x1000>;
>>> > + cpu = <&CPU3>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm3_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster0_funnel_in_port3>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11840000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11840000 0 0x1000>;
>>> > + cpu = <&CPU4>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm4_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port0>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11940000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11940000 0 0x1000>;
>>> > + cpu = <&CPU5>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm5_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port1>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11a40000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11a40000 0 0x1000>;
>>> > + cpu = <&CPU6>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm6_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port2>;
>>> > + };
>>> > + };
>>> > + };
>>> > +
>>> > + etm at 11b40000 {
>>> > + compatible = "arm,coresight-etm4x", "arm,primecell";
>>> > + reg = <0 0x11b40000 0 0x1000>;
>>> > + cpu = <&CPU7>;
>>> > + clocks = <&ext_26m>;
>>> > + clock-names = "apb_pclk";
>>> > +
>>> > + port {
>>> > + etm7_out: endpoint {
>>> > + remote-endpoint =
>>> > + <&cluster1_funnel_in_port3>;
>>> > + };
>>> > + };
>>> > + };
>>> > + };
>>> > +};
[...]
>>> >
>>> > _______________________________________________
>>> > linux-arm-kernel mailing list
>>> > linux-arm-kernel at lists.infradead.org
>>> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>> --
>> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> the body of a message to majordomo at vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
2017-02-23 6:20 ` Chunyan Zhang
(?)
@ 2017-02-23 10:56 ` Sudeep Holla
-1 siblings, 0 replies; 48+ messages in thread
From: Sudeep Holla @ 2017-02-23 10:56 UTC (permalink / raw)
To: Chunyan Zhang
Cc: Mathieu Poirier, Sudeep Holla, Rob Herring, Mark Rutland,
Greg KH, Catalin Marinas, Will Deacon, Arnd Bergmann, devicetree,
Orson Zhai, linux-kernel, linux-arm-kernel
Hi Chunyan,
On 23/02/17 06:20, Chunyan Zhang wrote:
[...]
>>> I noticed Juno use the 2), would you suggest that way?
>>
>> It is better to describe the HW component themselves rather than where
>> they are in the topology - the address of the component will make sure
>> the names are unique. So just the component type (etm, funnel,
>> replicator, ....) and the address they are located at.
>>
>
> OK. And to avoid making other person confused in the future, is it
> better to revise juno-base.dtsi according to this convention?
>
Yes, it was noticed by Olof and should be now fixed for v4.11(already
queued). You can check linux-next if you want to have a look before it
gets merged.
--
Regards,
Sudeep
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-23 10:56 ` Sudeep Holla
0 siblings, 0 replies; 48+ messages in thread
From: Sudeep Holla @ 2017-02-23 10:56 UTC (permalink / raw)
To: Chunyan Zhang
Cc: Mark Rutland, devicetree, Orson Zhai, Arnd Bergmann,
Mathieu Poirier, Greg KH, Sudeep Holla, Will Deacon,
linux-kernel, Rob Herring, Catalin Marinas, linux-arm-kernel
Hi Chunyan,
On 23/02/17 06:20, Chunyan Zhang wrote:
[...]
>>> I noticed Juno use the 2), would you suggest that way?
>>
>> It is better to describe the HW component themselves rather than where
>> they are in the topology - the address of the component will make sure
>> the names are unique. So just the component type (etm, funnel,
>> replicator, ....) and the address they are located at.
>>
>
> OK. And to avoid making other person confused in the future, is it
> better to revise juno-base.dtsi according to this convention?
>
Yes, it was noticed by Olof and should be now fixed for v4.11(already
queued). You can check linux-next if you want to have a look before it
gets merged.
--
Regards,
Sudeep
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-23 10:56 ` Sudeep Holla
0 siblings, 0 replies; 48+ messages in thread
From: Sudeep Holla @ 2017-02-23 10:56 UTC (permalink / raw)
To: linux-arm-kernel
Hi Chunyan,
On 23/02/17 06:20, Chunyan Zhang wrote:
[...]
>>> I noticed Juno use the 2), would you suggest that way?
>>
>> It is better to describe the HW component themselves rather than where
>> they are in the topology - the address of the component will make sure
>> the names are unique. So just the component type (etm, funnel,
>> replicator, ....) and the address they are located at.
>>
>
> OK. And to avoid making other person confused in the future, is it
> better to revise juno-base.dtsi according to this convention?
>
Yes, it was noticed by Olof and should be now fixed for v4.11(already
queued). You can check linux-next if you want to have a look before it
gets merged.
--
Regards,
Sudeep
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-24 0:00 ` Rob Herring
0 siblings, 0 replies; 48+ messages in thread
From: Rob Herring @ 2017-02-24 0:00 UTC (permalink / raw)
To: Chunyan Zhang
Cc: Mark Rutland, Greg Kroah-Hartman, Catalin Marinas, Will Deacon,
Arnd Bergmann, Orson Zhai(翟京),
Sudeep Holla, linux-kernel, devicetree, linux-arm-kernel,
Lyra Zhang
On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
<chunyan.zhang@spreadtrum.com> wrote:
> From: Orson Zhai <orson.zhai@spreadtrum.com>
>
> SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>
> According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> and sp9860g dts is for the board level.
>
> Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> ---
> arch/arm64/boot/dts/sprd/Makefile | 3 +-
> arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> 4 files changed, 659 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>
> diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> index b658c5e..f0535e6 100644
> --- a/arch/arm64/boot/dts/sprd/Makefile
> +++ b/arch/arm64/boot/dts/sprd/Makefile
> @@ -1,4 +1,5 @@
> -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> + sp9860g-1h10.dtb
>
> always := $(dtb-y)
> subdir-y := $(dts-dirs)
> diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> new file mode 100644
> index 0000000..73deb4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> @@ -0,0 +1,531 @@
> +/*
> + * Spreadtrum SP9860 SoC DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
Please use SPDX-License-Identifier tag instead.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include "whale2.dtsi"
> +
> +/ {
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> + core1 {
> + cpu = <&CPU1>;
> + };
> + core2 {
> + cpu = <&CPU2>;
> + };
> + core3 {
> + cpu = <&CPU3>;
> + };
> + };
> +
> + cluster1 {
> + core0 {
> + cpu = <&CPU4>;
> + };
> + core1 {
> + cpu = <&CPU5>;
> + };
> + core2 {
> + cpu = <&CPU6>;
> + };
> + core3 {
> + cpu = <&CPU7>;
> + };
> + };
> + };
> +
> + CPU0: cpu@530000 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530000>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU1: cpu@530001 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530001>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU2: cpu@530002 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530002>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU3: cpu@530003 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530003>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU4: cpu@530100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530100>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU5: cpu@530101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530101>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU6: cpu@530102 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530102>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU7: cpu@530103 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530103>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> + };
> +
> + idle-states{
> + entry-method = "arm,psci";
> +
> + CORE_PD: core_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <700>;
> + min-residency-us = <2500>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x00010002>;
> + };
> +
> + CLUSTER_PD: cluster_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <1000>;
> + min-residency-us = <3000>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x01010003>;
> + };
> + };
> +
> + gic: interrupt-controller@12001000 {
> + compatible = "arm,gic-400";
> + reg = <0 0x12001000 0 0x1000>,
> + <0 0x12002000 0 0x2000>,
> + <0 0x12004000 0 0x2000>,
> + <0 0x12006000 0 0x2000>;
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + psci {
> + compatible = "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&CPU0>,
> + <&CPU1>,
> + <&CPU2>,
> + <&CPU3>,
> + <&CPU4>,
> + <&CPU5>,
> + <&CPU6>,
> + <&CPU7>;
> + };
> +
> + soc {
> + soc_funnel: funnel@10001000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x10001000 0 0x1000>;
If all the devices are within 0x1xxxxxxx, then use ranges property to
limit the address range. It doesn't look like address or size cells
needs to be 2.
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + soc_funnel_out_port: endpoint {
> + remote-endpoint = <&etb_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + soc_funnel_in_port: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&main_funnel_out_port>;
> + };
> + };
> + };
> + };
> +
> + etb@10003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x10003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + port {
> + etb_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&soc_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster0_funnel: funnel@11001000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11001000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + cluster0_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster0_etf_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + cluster0_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm0_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + cluster0_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm1_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <2>;
> + cluster0_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm2_out>;
> + };
> + };
> +
> + port@4 {
> + reg = <4>;
> + cluster0_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm3_out>;
> + };
> + };
> + };
> + };
> +
> + cluster1_funnel: funnel@11002000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11002000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + cluster1_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster1_etf_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + cluster1_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm4_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + cluster1_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm5_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <2>;
> + cluster1_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm6_out>;
> + };
> + };
> +
> + port@4 {
> + reg = <3>;
> + cluster1_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm7_out>;
> + };
> + };
> + };
> + };
> +
> + cluster0_etf: etf@11003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port@0 {
> + cluster0_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port0>;
> + };
> + };
> +
> + port@1 {
> + cluster0_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster1_etf: etf@11004000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11004000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port@0 {
> + cluster1_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port1>;
> + };
> + };
> +
> + port@1 {
> + cluster1_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_funnel_out_port>;
> + };
> + };
> + };
> +
> + main_funnel: funnel@11005000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11005000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + main_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&soc_funnel_in_port>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + main_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_etf_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + main_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_etf_out>;
> + };
> + };
> + };
> + };
> +
> + etm@11440000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11440000 0 0x1000>;
> + cpu = <&CPU0>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm0_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm@11540000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11540000 0 0x1000>;
> + cpu = <&CPU1>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm1_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm@11640000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11640000 0 0x1000>;
> + cpu = <&CPU2>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm2_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm@11740000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11740000 0 0x1000>;
> + cpu = <&CPU3>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm3_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port3>;
> + };
> + };
> + };
> +
> + etm@11840000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11840000 0 0x1000>;
> + cpu = <&CPU4>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm4_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm@11940000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11940000 0 0x1000>;
> + cpu = <&CPU5>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm5_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm@11a40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11a40000 0 0x1000>;
> + cpu = <&CPU6>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm6_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm@11b40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11b40000 0 0x1000>;
> + cpu = <&CPU7>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm7_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port3>;
> + };
> + };
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> new file mode 100644
> index 0000000..5faa452
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> @@ -0,0 +1,56 @@
> +/*
> + * Spreadtrum SP9860g board DTS file
> + *
> + * Copyright (C) 2017, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/dts-v1/;
> +
> +#include "sc9860.dtsi"
> +
> +/ {
> + model = "Spreadtrum SP9860G 3GFHD Board";
> +
> + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> +
> + aliases {
> + serial0 = &uart0; /* for Bluetooth */
> + serial1 = &uart1; /* UART console */
> + serial2 = &uart2; /* Reserved */
> + serial3 = &uart3; /* for GPS */
> + };
> +
> + memory{
> + device_type = "memory";
> + reg = <0x0 0x80000000 0 0x60000000>,
> + <0x1 0x80000000 0 0x60000000>;
> + };
> +
> + chosen {
> + stdout-path = "serial1:115200n8";
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> new file mode 100644
> index 0000000..64f06d9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> @@ -0,0 +1,70 @@
> +/*
> + * Spreadtrum Whale2 SoC platform peripherals DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + soc: soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + ap-apb {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x70000000 0x10000000>;
Probably you should have 2 buses for each range of addresses.
> +
> + uart0: serial@70000000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x000000 0x100>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart1: serial@70100000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x100000 0x100>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart2: serial@70200000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x200000 0x100>;
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart3: serial@70300000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x300000 0x100>;
> + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> + };
> +
> + ext_26m: ext-26m {
This should be at the top-level. It is not part of the bus.
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "ext_26m";
> + };
> + };
> +};
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-24 0:00 ` Rob Herring
0 siblings, 0 replies; 48+ messages in thread
From: Rob Herring @ 2017-02-24 0:00 UTC (permalink / raw)
To: Chunyan Zhang
Cc: Mark Rutland, Greg Kroah-Hartman, Catalin Marinas, Will Deacon,
Arnd Bergmann, Orson Zhai(翟京),
Sudeep Holla, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lyra Zhang
On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
<chunyan.zhang-lxIno14LUO0EEoCn2XhGlw@public.gmane.org> wrote:
> From: Orson Zhai <orson.zhai-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
>
> SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>
> According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> and sp9860g dts is for the board level.
>
> Signed-off-by: Orson Zhai <orson.zhai-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
> Signed-off-by: Chunyan Zhang <chunyan.zhang-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
> ---
> arch/arm64/boot/dts/sprd/Makefile | 3 +-
> arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> 4 files changed, 659 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>
> diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> index b658c5e..f0535e6 100644
> --- a/arch/arm64/boot/dts/sprd/Makefile
> +++ b/arch/arm64/boot/dts/sprd/Makefile
> @@ -1,4 +1,5 @@
> -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> + sp9860g-1h10.dtb
>
> always := $(dtb-y)
> subdir-y := $(dts-dirs)
> diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> new file mode 100644
> index 0000000..73deb4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> @@ -0,0 +1,531 @@
> +/*
> + * Spreadtrum SP9860 SoC DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
Please use SPDX-License-Identifier tag instead.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include "whale2.dtsi"
> +
> +/ {
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> + core1 {
> + cpu = <&CPU1>;
> + };
> + core2 {
> + cpu = <&CPU2>;
> + };
> + core3 {
> + cpu = <&CPU3>;
> + };
> + };
> +
> + cluster1 {
> + core0 {
> + cpu = <&CPU4>;
> + };
> + core1 {
> + cpu = <&CPU5>;
> + };
> + core2 {
> + cpu = <&CPU6>;
> + };
> + core3 {
> + cpu = <&CPU7>;
> + };
> + };
> + };
> +
> + CPU0: cpu@530000 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530000>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU1: cpu@530001 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530001>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU2: cpu@530002 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530002>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU3: cpu@530003 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530003>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU4: cpu@530100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530100>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU5: cpu@530101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530101>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU6: cpu@530102 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530102>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU7: cpu@530103 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530103>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> + };
> +
> + idle-states{
> + entry-method = "arm,psci";
> +
> + CORE_PD: core_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <700>;
> + min-residency-us = <2500>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x00010002>;
> + };
> +
> + CLUSTER_PD: cluster_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <1000>;
> + min-residency-us = <3000>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x01010003>;
> + };
> + };
> +
> + gic: interrupt-controller@12001000 {
> + compatible = "arm,gic-400";
> + reg = <0 0x12001000 0 0x1000>,
> + <0 0x12002000 0 0x2000>,
> + <0 0x12004000 0 0x2000>,
> + <0 0x12006000 0 0x2000>;
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + psci {
> + compatible = "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&CPU0>,
> + <&CPU1>,
> + <&CPU2>,
> + <&CPU3>,
> + <&CPU4>,
> + <&CPU5>,
> + <&CPU6>,
> + <&CPU7>;
> + };
> +
> + soc {
> + soc_funnel: funnel@10001000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x10001000 0 0x1000>;
If all the devices are within 0x1xxxxxxx, then use ranges property to
limit the address range. It doesn't look like address or size cells
needs to be 2.
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + soc_funnel_out_port: endpoint {
> + remote-endpoint = <&etb_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + soc_funnel_in_port: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&main_funnel_out_port>;
> + };
> + };
> + };
> + };
> +
> + etb@10003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x10003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + port {
> + etb_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&soc_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster0_funnel: funnel@11001000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11001000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + cluster0_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster0_etf_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + cluster0_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm0_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + cluster0_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm1_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <2>;
> + cluster0_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm2_out>;
> + };
> + };
> +
> + port@4 {
> + reg = <4>;
> + cluster0_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm3_out>;
> + };
> + };
> + };
> + };
> +
> + cluster1_funnel: funnel@11002000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11002000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + cluster1_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster1_etf_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + cluster1_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm4_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + cluster1_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm5_out>;
> + };
> + };
> +
> + port@3 {
> + reg = <2>;
> + cluster1_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm6_out>;
> + };
> + };
> +
> + port@4 {
> + reg = <3>;
> + cluster1_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm7_out>;
> + };
> + };
> + };
> + };
> +
> + cluster0_etf: etf@11003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port@0 {
> + cluster0_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port0>;
> + };
> + };
> +
> + port@1 {
> + cluster0_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster1_etf: etf@11004000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11004000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port@0 {
> + cluster1_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port1>;
> + };
> + };
> +
> + port@1 {
> + cluster1_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_funnel_out_port>;
> + };
> + };
> + };
> +
> + main_funnel: funnel@11005000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11005000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + main_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&soc_funnel_in_port>;
> + };
> + };
> +
> + port@1 {
> + reg = <0>;
> + main_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_etf_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <1>;
> + main_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_etf_out>;
> + };
> + };
> + };
> + };
> +
> + etm@11440000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11440000 0 0x1000>;
> + cpu = <&CPU0>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm0_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm@11540000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11540000 0 0x1000>;
> + cpu = <&CPU1>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm1_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm@11640000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11640000 0 0x1000>;
> + cpu = <&CPU2>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm2_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm@11740000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11740000 0 0x1000>;
> + cpu = <&CPU3>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm3_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port3>;
> + };
> + };
> + };
> +
> + etm@11840000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11840000 0 0x1000>;
> + cpu = <&CPU4>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm4_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm@11940000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11940000 0 0x1000>;
> + cpu = <&CPU5>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm5_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm@11a40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11a40000 0 0x1000>;
> + cpu = <&CPU6>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm6_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm@11b40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11b40000 0 0x1000>;
> + cpu = <&CPU7>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm7_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port3>;
> + };
> + };
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> new file mode 100644
> index 0000000..5faa452
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> @@ -0,0 +1,56 @@
> +/*
> + * Spreadtrum SP9860g board DTS file
> + *
> + * Copyright (C) 2017, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/dts-v1/;
> +
> +#include "sc9860.dtsi"
> +
> +/ {
> + model = "Spreadtrum SP9860G 3GFHD Board";
> +
> + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> +
> + aliases {
> + serial0 = &uart0; /* for Bluetooth */
> + serial1 = &uart1; /* UART console */
> + serial2 = &uart2; /* Reserved */
> + serial3 = &uart3; /* for GPS */
> + };
> +
> + memory{
> + device_type = "memory";
> + reg = <0x0 0x80000000 0 0x60000000>,
> + <0x1 0x80000000 0 0x60000000>;
> + };
> +
> + chosen {
> + stdout-path = "serial1:115200n8";
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> new file mode 100644
> index 0000000..64f06d9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> @@ -0,0 +1,70 @@
> +/*
> + * Spreadtrum Whale2 SoC platform peripherals DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + soc: soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + ap-apb {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x70000000 0x10000000>;
Probably you should have 2 buses for each range of addresses.
> +
> + uart0: serial@70000000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x000000 0x100>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart1: serial@70100000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x100000 0x100>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart2: serial@70200000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x200000 0x100>;
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart3: serial@70300000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x300000 0x100>;
> + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> + };
> +
> + ext_26m: ext-26m {
This should be at the top-level. It is not part of the bus.
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "ext_26m";
> + };
> + };
> +};
> --
> 2.7.4
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-24 0:00 ` Rob Herring
0 siblings, 0 replies; 48+ messages in thread
From: Rob Herring @ 2017-02-24 0:00 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
<chunyan.zhang@spreadtrum.com> wrote:
> From: Orson Zhai <orson.zhai@spreadtrum.com>
>
> SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>
> According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> and sp9860g dts is for the board level.
>
> Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> ---
> arch/arm64/boot/dts/sprd/Makefile | 3 +-
> arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> 4 files changed, 659 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>
> diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> index b658c5e..f0535e6 100644
> --- a/arch/arm64/boot/dts/sprd/Makefile
> +++ b/arch/arm64/boot/dts/sprd/Makefile
> @@ -1,4 +1,5 @@
> -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> + sp9860g-1h10.dtb
>
> always := $(dtb-y)
> subdir-y := $(dts-dirs)
> diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> new file mode 100644
> index 0000000..73deb4e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> @@ -0,0 +1,531 @@
> +/*
> + * Spreadtrum SP9860 SoC DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
Please use SPDX-License-Identifier tag instead.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include "whale2.dtsi"
> +
> +/ {
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> + core1 {
> + cpu = <&CPU1>;
> + };
> + core2 {
> + cpu = <&CPU2>;
> + };
> + core3 {
> + cpu = <&CPU3>;
> + };
> + };
> +
> + cluster1 {
> + core0 {
> + cpu = <&CPU4>;
> + };
> + core1 {
> + cpu = <&CPU5>;
> + };
> + core2 {
> + cpu = <&CPU6>;
> + };
> + core3 {
> + cpu = <&CPU7>;
> + };
> + };
> + };
> +
> + CPU0: cpu at 530000 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530000>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU1: cpu at 530001 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530001>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU2: cpu at 530002 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530002>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU3: cpu at 530003 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530003>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU4: cpu at 530100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530100>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU5: cpu at 530101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530101>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU6: cpu at 530102 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530102>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> +
> + CPU7: cpu at 530103 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a53", "arm,armv8";
> + reg = <0x0 0x530103>;
> + enable-method = "psci";
> + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> + };
> + };
> +
> + idle-states{
> + entry-method = "arm,psci";
> +
> + CORE_PD: core_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <700>;
> + min-residency-us = <2500>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x00010002>;
> + };
> +
> + CLUSTER_PD: cluster_pd {
> + compatible = "arm,idle-state";
> + entry-latency-us = <1000>;
> + exit-latency-us = <1000>;
> + min-residency-us = <3000>;
> + local-timer-stop;
> + arm,psci-suspend-param = <0x01010003>;
> + };
> + };
> +
> + gic: interrupt-controller at 12001000 {
> + compatible = "arm,gic-400";
> + reg = <0 0x12001000 0 0x1000>,
> + <0 0x12002000 0 0x2000>,
> + <0 0x12004000 0 0x2000>,
> + <0 0x12006000 0 0x2000>;
> + #interrupt-cells = <3>;
> + interrupt-controller;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + psci {
> + compatible = "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>,
> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> + | IRQ_TYPE_LEVEL_LOW)>;
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&CPU0>,
> + <&CPU1>,
> + <&CPU2>,
> + <&CPU3>,
> + <&CPU4>,
> + <&CPU5>,
> + <&CPU6>,
> + <&CPU7>;
> + };
> +
> + soc {
> + soc_funnel: funnel at 10001000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x10001000 0 0x1000>;
If all the devices are within 0x1xxxxxxx, then use ranges property to
limit the address range. It doesn't look like address or size cells
needs to be 2.
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + soc_funnel_out_port: endpoint {
> + remote-endpoint = <&etb_in>;
> + };
> + };
> +
> + port at 1 {
> + reg = <0>;
> + soc_funnel_in_port: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&main_funnel_out_port>;
> + };
> + };
> + };
> + };
> +
> + etb at 10003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x10003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + port {
> + etb_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&soc_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster0_funnel: funnel at 11001000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11001000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + cluster0_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster0_etf_in>;
> + };
> + };
> +
> + port at 1 {
> + reg = <0>;
> + cluster0_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm0_out>;
> + };
> + };
> +
> + port at 2 {
> + reg = <1>;
> + cluster0_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm1_out>;
> + };
> + };
> +
> + port at 3 {
> + reg = <2>;
> + cluster0_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm2_out>;
> + };
> + };
> +
> + port at 4 {
> + reg = <4>;
> + cluster0_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm3_out>;
> + };
> + };
> + };
> + };
> +
> + cluster1_funnel: funnel at 11002000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11002000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + cluster1_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&cluster1_etf_in>;
> + };
> + };
> +
> + port at 1 {
> + reg = <0>;
> + cluster1_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm4_out>;
> + };
> + };
> +
> + port at 2 {
> + reg = <1>;
> + cluster1_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm5_out>;
> + };
> + };
> +
> + port at 3 {
> + reg = <2>;
> + cluster1_funnel_in_port2: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm6_out>;
> + };
> + };
> +
> + port at 4 {
> + reg = <3>;
> + cluster1_funnel_in_port3: endpoint {
> + slave-mode;
> + remote-endpoint = <&etm7_out>;
> + };
> + };
> + };
> + };
> +
> + cluster0_etf: etf at 11003000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11003000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port at 0 {
> + cluster0_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port0>;
> + };
> + };
> +
> + port at 1 {
> + cluster0_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_funnel_out_port>;
> + };
> + };
> + };
> +
> + cluster1_etf: etf at 11004000 {
> + compatible = "arm,coresight-tmc", "arm,primecell";
> + reg = <0 0x11004000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port at 0 {
> + cluster1_etf_out: endpoint {
> + remote-endpoint =
> + <&main_funnel_in_port1>;
> + };
> + };
> +
> + port at 1 {
> + cluster1_etf_in: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_funnel_out_port>;
> + };
> + };
> + };
> +
> + main_funnel: funnel at 11005000 {
> + compatible = "arm,coresight-funnel", "arm,primecell";
> + reg = <0 0x11005000 0 0x1000>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port at 0 {
> + reg = <0>;
> + main_funnel_out_port: endpoint {
> + remote-endpoint =
> + <&soc_funnel_in_port>;
> + };
> + };
> +
> + port at 1 {
> + reg = <0>;
> + main_funnel_in_port0: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster0_etf_out>;
> + };
> + };
> +
> + port at 2 {
> + reg = <1>;
> + main_funnel_in_port1: endpoint {
> + slave-mode;
> + remote-endpoint =
> + <&cluster1_etf_out>;
> + };
> + };
> + };
> + };
> +
> + etm at 11440000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11440000 0 0x1000>;
> + cpu = <&CPU0>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm0_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm at 11540000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11540000 0 0x1000>;
> + cpu = <&CPU1>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm1_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm at 11640000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11640000 0 0x1000>;
> + cpu = <&CPU2>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm2_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm at 11740000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11740000 0 0x1000>;
> + cpu = <&CPU3>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm3_out: endpoint {
> + remote-endpoint =
> + <&cluster0_funnel_in_port3>;
> + };
> + };
> + };
> +
> + etm at 11840000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11840000 0 0x1000>;
> + cpu = <&CPU4>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm4_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port0>;
> + };
> + };
> + };
> +
> + etm at 11940000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11940000 0 0x1000>;
> + cpu = <&CPU5>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm5_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port1>;
> + };
> + };
> + };
> +
> + etm at 11a40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11a40000 0 0x1000>;
> + cpu = <&CPU6>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm6_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port2>;
> + };
> + };
> + };
> +
> + etm at 11b40000 {
> + compatible = "arm,coresight-etm4x", "arm,primecell";
> + reg = <0 0x11b40000 0 0x1000>;
> + cpu = <&CPU7>;
> + clocks = <&ext_26m>;
> + clock-names = "apb_pclk";
> +
> + port {
> + etm7_out: endpoint {
> + remote-endpoint =
> + <&cluster1_funnel_in_port3>;
> + };
> + };
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> new file mode 100644
> index 0000000..5faa452
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> @@ -0,0 +1,56 @@
> +/*
> + * Spreadtrum SP9860g board DTS file
> + *
> + * Copyright (C) 2017, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/dts-v1/;
> +
> +#include "sc9860.dtsi"
> +
> +/ {
> + model = "Spreadtrum SP9860G 3GFHD Board";
> +
> + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> +
> + aliases {
> + serial0 = &uart0; /* for Bluetooth */
> + serial1 = &uart1; /* UART console */
> + serial2 = &uart2; /* Reserved */
> + serial3 = &uart3; /* for GPS */
> + };
> +
> + memory{
> + device_type = "memory";
> + reg = <0x0 0x80000000 0 0x60000000>,
> + <0x1 0x80000000 0 0x60000000>;
> + };
> +
> + chosen {
> + stdout-path = "serial1:115200n8";
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart3 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> new file mode 100644
> index 0000000..64f06d9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> @@ -0,0 +1,70 @@
> +/*
> + * Spreadtrum Whale2 SoC platform peripherals DTS file
> + *
> + * Copyright (C) 2016, Spreadtrum Communications Inc.
> + *
> + * This file is licensed under a dual GPLv2 or X11 license.
> + */
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + soc: soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + ap-apb {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x70000000 0x10000000>;
Probably you should have 2 buses for each range of addresses.
> +
> + uart0: serial at 70000000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x000000 0x100>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart1: serial at 70100000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x100000 0x100>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart2: serial at 70200000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x200000 0x100>;
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart3: serial at 70300000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x300000 0x100>;
> + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> + };
> +
> + ext_26m: ext-26m {
This should be at the top-level. It is not part of the bus.
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "ext_26m";
> + };
> + };
> +};
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
2017-02-24 0:00 ` Rob Herring
(?)
@ 2017-02-24 7:57 ` Chunyan Zhang
-1 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-24 7:57 UTC (permalink / raw)
To: Rob Herring
Cc: Mark Rutland, Greg Kroah-Hartman, Catalin Marinas, Will Deacon,
Arnd Bergmann, Orson Zhai(翟京),
Sudeep Holla, linux-kernel, devicetree, linux-arm-kernel,
Lyra Zhang
On 四, 2月 23, 2017 at 06:00:20下午 -0600, Rob Herring wrote:
> On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
> <chunyan.zhang@spreadtrum.com> wrote:
> > From: Orson Zhai <orson.zhai@spreadtrum.com>
> >
> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
> >
> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> > and sp9860g dts is for the board level.
> >
> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> > ---
> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> > 4 files changed, 659 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> > index b658c5e..f0535e6 100644
> > --- a/arch/arm64/boot/dts/sprd/Makefile
> > +++ b/arch/arm64/boot/dts/sprd/Makefile
> > @@ -1,4 +1,5 @@
> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> > + sp9860g-1h10.dtb
> >
> > always := $(dtb-y)
> > subdir-y := $(dts-dirs)
> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > new file mode 100644
> > index 0000000..73deb4e
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > @@ -0,0 +1,531 @@
> > +/*
> > + * Spreadtrum SP9860 SoC DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
>
> Please use SPDX-License-Identifier tag instead.
>
Just to double check, if I use it like:
SPDX-License-Identifier: (GPL-2.0 or X11)
Is this what you mean?
Will this file still be licensed under the same terms it was, right?
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include "whale2.dtsi"
> > +
> > +/ {
> > + cpus {
> > + #address-cells = <2>;
> > + #size-cells = <0>;
> > +
> > + cpu-map {
> > + cluster0 {
> > + core0 {
> > + cpu = <&CPU0>;
> > + };
> > + core1 {
> > + cpu = <&CPU1>;
> > + };
> > + core2 {
> > + cpu = <&CPU2>;
> > + };
> > + core3 {
> > + cpu = <&CPU3>;
> > + };
> > + };
> > +
> > + cluster1 {
> > + core0 {
> > + cpu = <&CPU4>;
> > + };
> > + core1 {
> > + cpu = <&CPU5>;
> > + };
> > + core2 {
> > + cpu = <&CPU6>;
> > + };
> > + core3 {
> > + cpu = <&CPU7>;
> > + };
> > + };
> > + };
> > +
> > + CPU0: cpu@530000 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530000>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU1: cpu@530001 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530001>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU2: cpu@530002 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530002>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU3: cpu@530003 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530003>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU4: cpu@530100 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530100>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU5: cpu@530101 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530101>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU6: cpu@530102 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530102>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU7: cpu@530103 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530103>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > + };
> > +
> > + idle-states{
> > + entry-method = "arm,psci";
> > +
> > + CORE_PD: core_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <700>;
> > + min-residency-us = <2500>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x00010002>;
> > + };
> > +
> > + CLUSTER_PD: cluster_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <1000>;
> > + min-residency-us = <3000>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x01010003>;
> > + };
> > + };
> > +
> > + gic: interrupt-controller@12001000 {
> > + compatible = "arm,gic-400";
> > + reg = <0 0x12001000 0 0x1000>,
> > + <0 0x12002000 0 0x2000>,
> > + <0 0x12004000 0 0x2000>,
> > + <0 0x12006000 0 0x2000>;
> > + #interrupt-cells = <3>;
> > + interrupt-controller;
> > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_HIGH)>;
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-0.2";
> > + method = "smc";
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>;
> > + };
> > +
> > + pmu {
> > + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> > + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-affinity = <&CPU0>,
> > + <&CPU1>,
> > + <&CPU2>,
> > + <&CPU3>,
> > + <&CPU4>,
> > + <&CPU5>,
> > + <&CPU6>,
> > + <&CPU7>;
> > + };
> > +
> > + soc {
> > + soc_funnel: funnel@10001000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x10001000 0 0x1000>;
>
> If all the devices are within 0x1xxxxxxx, then use ranges property to
> limit the address range. It doesn't look like address or size cells
> needs to be 2.
There're some devices not included in this DT for now whose addresses
is 64-bit. I will add more devices into this device tree later on.
>
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + soc_funnel_out_port: endpoint {
> > + remote-endpoint = <&etb_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + soc_funnel_in_port: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&main_funnel_out_port>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etb@10003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x10003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + port {
> > + etb_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&soc_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster0_funnel: funnel@11001000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11001000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + cluster0_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster0_etf_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + cluster0_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm0_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + cluster0_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm1_out>;
> > + };
> > + };
> > +
> > + port@3 {
> > + reg = <2>;
> > + cluster0_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm2_out>;
> > + };
> > + };
> > +
> > + port@4 {
> > + reg = <4>;
> > + cluster0_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm3_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster1_funnel: funnel@11002000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11002000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + cluster1_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster1_etf_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + cluster1_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm4_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + cluster1_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm5_out>;
> > + };
> > + };
> > +
> > + port@3 {
> > + reg = <2>;
> > + cluster1_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm6_out>;
> > + };
> > + };
> > +
> > + port@4 {
> > + reg = <3>;
> > + cluster1_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm7_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster0_etf: etf@11003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port@0 {
> > + cluster0_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port0>;
> > + };
> > + };
> > +
> > + port@1 {
> > + cluster0_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster1_etf: etf@11004000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11004000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port@0 {
> > + cluster1_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port1>;
> > + };
> > + };
> > +
> > + port@1 {
> > + cluster1_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + main_funnel: funnel@11005000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11005000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + main_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&soc_funnel_in_port>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + main_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_etf_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + main_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_etf_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etm@11440000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11440000 0 0x1000>;
> > + cpu = <&CPU0>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm0_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm@11540000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11540000 0 0x1000>;
> > + cpu = <&CPU1>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm1_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm@11640000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11640000 0 0x1000>;
> > + cpu = <&CPU2>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm2_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm@11740000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11740000 0 0x1000>;
> > + cpu = <&CPU3>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm3_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port3>;
> > + };
> > + };
> > + };
> > +
> > + etm@11840000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11840000 0 0x1000>;
> > + cpu = <&CPU4>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm4_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm@11940000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11940000 0 0x1000>;
> > + cpu = <&CPU5>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm5_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm@11a40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11a40000 0 0x1000>;
> > + cpu = <&CPU6>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm6_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm@11b40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11b40000 0 0x1000>;
> > + cpu = <&CPU7>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm7_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port3>;
> > + };
> > + };
> > + };
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > new file mode 100644
> > index 0000000..5faa452
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > @@ -0,0 +1,56 @@
> > +/*
> > + * Spreadtrum SP9860g board DTS file
> > + *
> > + * Copyright (C) 2017, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "sc9860.dtsi"
> > +
> > +/ {
> > + model = "Spreadtrum SP9860G 3GFHD Board";
> > +
> > + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> > +
> > + aliases {
> > + serial0 = &uart0; /* for Bluetooth */
> > + serial1 = &uart1; /* UART console */
> > + serial2 = &uart2; /* Reserved */
> > + serial3 = &uart3; /* for GPS */
> > + };
> > +
> > + memory{
> > + device_type = "memory";
> > + reg = <0x0 0x80000000 0 0x60000000>,
> > + <0x1 0x80000000 0 0x60000000>;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial1:115200n8";
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + status = "okay";
> > +};
> > +
> > +&uart3 {
> > + status = "okay";
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > new file mode 100644
> > index 0000000..64f06d9
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > @@ -0,0 +1,70 @@
> > +/*
> > + * Spreadtrum Whale2 SoC platform peripherals DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/ {
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + soc: soc {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + ap-apb {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0 0x0 0x70000000 0x10000000>;
>
> Probably you should have 2 buses for each range of addresses.
I may not understand your point, I just looked at the SoC specification, the
address range of this AP APB bus is from 0x70000000 ~ 0x7fffffff.
>
> > +
> > + uart0: serial@70000000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x000000 0x100>;
> > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart1: serial@70100000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x100000 0x100>;
> > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial@70200000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x200000 0x100>;
> > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart3: serial@70300000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x300000 0x100>;
> > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + ext_26m: ext-26m {
>
> This should be at the top-level. It is not part of the bus.
This clock node is in 'soc' node, not under 'ap-apb'. Since there're other
clocks on SC9860 which would have 'reg' property, we thought this fixed
clock would be better under 'soc' with other clocks.
Thanks your comments,
Chunyan
>
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <26000000>;
> > + clock-output-names = "ext_26m";
> > + };
> > + };
> > +};
> > --
> > 2.7.4
> >
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-24 7:57 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-24 7:57 UTC (permalink / raw)
To: Rob Herring
Cc: Mark Rutland, devicetree, Orson Zhai(翟京),
Arnd Bergmann, Greg Kroah-Hartman, Sudeep Holla, Will Deacon,
linux-kernel, Lyra Zhang, Catalin Marinas, linux-arm-kernel
On 四, 2月 23, 2017 at 06:00:20下午 -0600, Rob Herring wrote:
> On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
> <chunyan.zhang@spreadtrum.com> wrote:
> > From: Orson Zhai <orson.zhai@spreadtrum.com>
> >
> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
> >
> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> > and sp9860g dts is for the board level.
> >
> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> > ---
> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> > 4 files changed, 659 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> > index b658c5e..f0535e6 100644
> > --- a/arch/arm64/boot/dts/sprd/Makefile
> > +++ b/arch/arm64/boot/dts/sprd/Makefile
> > @@ -1,4 +1,5 @@
> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> > + sp9860g-1h10.dtb
> >
> > always := $(dtb-y)
> > subdir-y := $(dts-dirs)
> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > new file mode 100644
> > index 0000000..73deb4e
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > @@ -0,0 +1,531 @@
> > +/*
> > + * Spreadtrum SP9860 SoC DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
>
> Please use SPDX-License-Identifier tag instead.
>
Just to double check, if I use it like:
SPDX-License-Identifier: (GPL-2.0 or X11)
Is this what you mean?
Will this file still be licensed under the same terms it was, right?
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include "whale2.dtsi"
> > +
> > +/ {
> > + cpus {
> > + #address-cells = <2>;
> > + #size-cells = <0>;
> > +
> > + cpu-map {
> > + cluster0 {
> > + core0 {
> > + cpu = <&CPU0>;
> > + };
> > + core1 {
> > + cpu = <&CPU1>;
> > + };
> > + core2 {
> > + cpu = <&CPU2>;
> > + };
> > + core3 {
> > + cpu = <&CPU3>;
> > + };
> > + };
> > +
> > + cluster1 {
> > + core0 {
> > + cpu = <&CPU4>;
> > + };
> > + core1 {
> > + cpu = <&CPU5>;
> > + };
> > + core2 {
> > + cpu = <&CPU6>;
> > + };
> > + core3 {
> > + cpu = <&CPU7>;
> > + };
> > + };
> > + };
> > +
> > + CPU0: cpu@530000 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530000>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU1: cpu@530001 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530001>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU2: cpu@530002 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530002>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU3: cpu@530003 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530003>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU4: cpu@530100 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530100>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU5: cpu@530101 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530101>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU6: cpu@530102 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530102>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU7: cpu@530103 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530103>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > + };
> > +
> > + idle-states{
> > + entry-method = "arm,psci";
> > +
> > + CORE_PD: core_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <700>;
> > + min-residency-us = <2500>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x00010002>;
> > + };
> > +
> > + CLUSTER_PD: cluster_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <1000>;
> > + min-residency-us = <3000>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x01010003>;
> > + };
> > + };
> > +
> > + gic: interrupt-controller@12001000 {
> > + compatible = "arm,gic-400";
> > + reg = <0 0x12001000 0 0x1000>,
> > + <0 0x12002000 0 0x2000>,
> > + <0 0x12004000 0 0x2000>,
> > + <0 0x12006000 0 0x2000>;
> > + #interrupt-cells = <3>;
> > + interrupt-controller;
> > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_HIGH)>;
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-0.2";
> > + method = "smc";
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>;
> > + };
> > +
> > + pmu {
> > + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> > + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-affinity = <&CPU0>,
> > + <&CPU1>,
> > + <&CPU2>,
> > + <&CPU3>,
> > + <&CPU4>,
> > + <&CPU5>,
> > + <&CPU6>,
> > + <&CPU7>;
> > + };
> > +
> > + soc {
> > + soc_funnel: funnel@10001000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x10001000 0 0x1000>;
>
> If all the devices are within 0x1xxxxxxx, then use ranges property to
> limit the address range. It doesn't look like address or size cells
> needs to be 2.
There're some devices not included in this DT for now whose addresses
is 64-bit. I will add more devices into this device tree later on.
>
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + soc_funnel_out_port: endpoint {
> > + remote-endpoint = <&etb_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + soc_funnel_in_port: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&main_funnel_out_port>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etb@10003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x10003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + port {
> > + etb_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&soc_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster0_funnel: funnel@11001000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11001000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + cluster0_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster0_etf_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + cluster0_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm0_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + cluster0_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm1_out>;
> > + };
> > + };
> > +
> > + port@3 {
> > + reg = <2>;
> > + cluster0_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm2_out>;
> > + };
> > + };
> > +
> > + port@4 {
> > + reg = <4>;
> > + cluster0_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm3_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster1_funnel: funnel@11002000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11002000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + cluster1_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster1_etf_in>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + cluster1_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm4_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + cluster1_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm5_out>;
> > + };
> > + };
> > +
> > + port@3 {
> > + reg = <2>;
> > + cluster1_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm6_out>;
> > + };
> > + };
> > +
> > + port@4 {
> > + reg = <3>;
> > + cluster1_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm7_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster0_etf: etf@11003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port@0 {
> > + cluster0_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port0>;
> > + };
> > + };
> > +
> > + port@1 {
> > + cluster0_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster1_etf: etf@11004000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11004000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port@0 {
> > + cluster1_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port1>;
> > + };
> > + };
> > +
> > + port@1 {
> > + cluster1_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + main_funnel: funnel@11005000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11005000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + main_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&soc_funnel_in_port>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <0>;
> > + main_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_etf_out>;
> > + };
> > + };
> > +
> > + port@2 {
> > + reg = <1>;
> > + main_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_etf_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etm@11440000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11440000 0 0x1000>;
> > + cpu = <&CPU0>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm0_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm@11540000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11540000 0 0x1000>;
> > + cpu = <&CPU1>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm1_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm@11640000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11640000 0 0x1000>;
> > + cpu = <&CPU2>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm2_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm@11740000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11740000 0 0x1000>;
> > + cpu = <&CPU3>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm3_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port3>;
> > + };
> > + };
> > + };
> > +
> > + etm@11840000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11840000 0 0x1000>;
> > + cpu = <&CPU4>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm4_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm@11940000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11940000 0 0x1000>;
> > + cpu = <&CPU5>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm5_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm@11a40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11a40000 0 0x1000>;
> > + cpu = <&CPU6>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm6_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm@11b40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11b40000 0 0x1000>;
> > + cpu = <&CPU7>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm7_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port3>;
> > + };
> > + };
> > + };
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > new file mode 100644
> > index 0000000..5faa452
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > @@ -0,0 +1,56 @@
> > +/*
> > + * Spreadtrum SP9860g board DTS file
> > + *
> > + * Copyright (C) 2017, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "sc9860.dtsi"
> > +
> > +/ {
> > + model = "Spreadtrum SP9860G 3GFHD Board";
> > +
> > + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> > +
> > + aliases {
> > + serial0 = &uart0; /* for Bluetooth */
> > + serial1 = &uart1; /* UART console */
> > + serial2 = &uart2; /* Reserved */
> > + serial3 = &uart3; /* for GPS */
> > + };
> > +
> > + memory{
> > + device_type = "memory";
> > + reg = <0x0 0x80000000 0 0x60000000>,
> > + <0x1 0x80000000 0 0x60000000>;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial1:115200n8";
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + status = "okay";
> > +};
> > +
> > +&uart3 {
> > + status = "okay";
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > new file mode 100644
> > index 0000000..64f06d9
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > @@ -0,0 +1,70 @@
> > +/*
> > + * Spreadtrum Whale2 SoC platform peripherals DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/ {
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + soc: soc {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + ap-apb {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0 0x0 0x70000000 0x10000000>;
>
> Probably you should have 2 buses for each range of addresses.
I may not understand your point, I just looked at the SoC specification, the
address range of this AP APB bus is from 0x70000000 ~ 0x7fffffff.
>
> > +
> > + uart0: serial@70000000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x000000 0x100>;
> > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart1: serial@70100000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x100000 0x100>;
> > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial@70200000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x200000 0x100>;
> > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart3: serial@70300000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x300000 0x100>;
> > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + ext_26m: ext-26m {
>
> This should be at the top-level. It is not part of the bus.
This clock node is in 'soc' node, not under 'ap-apb'. Since there're other
clocks on SC9860 which would have 'reg' property, we thought this fixed
clock would be better under 'soc' with other clocks.
Thanks your comments,
Chunyan
>
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <26000000>;
> > + clock-output-names = "ext_26m";
> > + };
> > + };
> > +};
> > --
> > 2.7.4
> >
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-24 7:57 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-24 7:57 UTC (permalink / raw)
To: linux-arm-kernel
On ?, 2? 23, 2017 at 06:00:20?? -0600, Rob Herring wrote:
> On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
> <chunyan.zhang@spreadtrum.com> wrote:
> > From: Orson Zhai <orson.zhai@spreadtrum.com>
> >
> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
> >
> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
> > and sp9860g dts is for the board level.
> >
> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> > ---
> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
> > 4 files changed, 659 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
> > index b658c5e..f0535e6 100644
> > --- a/arch/arm64/boot/dts/sprd/Makefile
> > +++ b/arch/arm64/boot/dts/sprd/Makefile
> > @@ -1,4 +1,5 @@
> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
> > + sp9860g-1h10.dtb
> >
> > always := $(dtb-y)
> > subdir-y := $(dts-dirs)
> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > new file mode 100644
> > index 0000000..73deb4e
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
> > @@ -0,0 +1,531 @@
> > +/*
> > + * Spreadtrum SP9860 SoC DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
>
> Please use SPDX-License-Identifier tag instead.
>
Just to double check, if I use it like:
SPDX-License-Identifier: (GPL-2.0 or X11)
Is this what you mean?
Will this file still be licensed under the same terms it was, right?
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include "whale2.dtsi"
> > +
> > +/ {
> > + cpus {
> > + #address-cells = <2>;
> > + #size-cells = <0>;
> > +
> > + cpu-map {
> > + cluster0 {
> > + core0 {
> > + cpu = <&CPU0>;
> > + };
> > + core1 {
> > + cpu = <&CPU1>;
> > + };
> > + core2 {
> > + cpu = <&CPU2>;
> > + };
> > + core3 {
> > + cpu = <&CPU3>;
> > + };
> > + };
> > +
> > + cluster1 {
> > + core0 {
> > + cpu = <&CPU4>;
> > + };
> > + core1 {
> > + cpu = <&CPU5>;
> > + };
> > + core2 {
> > + cpu = <&CPU6>;
> > + };
> > + core3 {
> > + cpu = <&CPU7>;
> > + };
> > + };
> > + };
> > +
> > + CPU0: cpu at 530000 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530000>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU1: cpu at 530001 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530001>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU2: cpu at 530002 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530002>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU3: cpu at 530003 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530003>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU4: cpu at 530100 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530100>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU5: cpu at 530101 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530101>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU6: cpu at 530102 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530102>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > +
> > + CPU7: cpu at 530103 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + reg = <0x0 0x530103>;
> > + enable-method = "psci";
> > + cpu-idle-states = <&CORE_PD &CLUSTER_PD>;
> > + };
> > + };
> > +
> > + idle-states{
> > + entry-method = "arm,psci";
> > +
> > + CORE_PD: core_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <700>;
> > + min-residency-us = <2500>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x00010002>;
> > + };
> > +
> > + CLUSTER_PD: cluster_pd {
> > + compatible = "arm,idle-state";
> > + entry-latency-us = <1000>;
> > + exit-latency-us = <1000>;
> > + min-residency-us = <3000>;
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x01010003>;
> > + };
> > + };
> > +
> > + gic: interrupt-controller at 12001000 {
> > + compatible = "arm,gic-400";
> > + reg = <0 0x12001000 0 0x1000>,
> > + <0 0x12002000 0 0x2000>,
> > + <0 0x12004000 0 0x2000>,
> > + <0 0x12006000 0 0x2000>;
> > + #interrupt-cells = <3>;
> > + interrupt-controller;
> > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_HIGH)>;
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-0.2";
> > + method = "smc";
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8)
> > + | IRQ_TYPE_LEVEL_LOW)>;
> > + };
> > +
> > + pmu {
> > + compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
> > + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-affinity = <&CPU0>,
> > + <&CPU1>,
> > + <&CPU2>,
> > + <&CPU3>,
> > + <&CPU4>,
> > + <&CPU5>,
> > + <&CPU6>,
> > + <&CPU7>;
> > + };
> > +
> > + soc {
> > + soc_funnel: funnel at 10001000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x10001000 0 0x1000>;
>
> If all the devices are within 0x1xxxxxxx, then use ranges property to
> limit the address range. It doesn't look like address or size cells
> needs to be 2.
There're some devices not included in this DT for now whose addresses
is 64-bit. I will add more devices into this device tree later on.
>
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + soc_funnel_out_port: endpoint {
> > + remote-endpoint = <&etb_in>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + reg = <0>;
> > + soc_funnel_in_port: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&main_funnel_out_port>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etb at 10003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x10003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + port {
> > + etb_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&soc_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster0_funnel: funnel at 11001000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11001000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + cluster0_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster0_etf_in>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + reg = <0>;
> > + cluster0_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm0_out>;
> > + };
> > + };
> > +
> > + port at 2 {
> > + reg = <1>;
> > + cluster0_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm1_out>;
> > + };
> > + };
> > +
> > + port at 3 {
> > + reg = <2>;
> > + cluster0_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm2_out>;
> > + };
> > + };
> > +
> > + port at 4 {
> > + reg = <4>;
> > + cluster0_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm3_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster1_funnel: funnel at 11002000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11002000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + cluster1_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&cluster1_etf_in>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + reg = <0>;
> > + cluster1_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm4_out>;
> > + };
> > + };
> > +
> > + port at 2 {
> > + reg = <1>;
> > + cluster1_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm5_out>;
> > + };
> > + };
> > +
> > + port at 3 {
> > + reg = <2>;
> > + cluster1_funnel_in_port2: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm6_out>;
> > + };
> > + };
> > +
> > + port at 4 {
> > + reg = <3>;
> > + cluster1_funnel_in_port3: endpoint {
> > + slave-mode;
> > + remote-endpoint = <&etm7_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + cluster0_etf: etf at 11003000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11003000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port at 0 {
> > + cluster0_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port0>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + cluster0_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + cluster1_etf: etf at 11004000 {
> > + compatible = "arm,coresight-tmc", "arm,primecell";
> > + reg = <0 0x11004000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port at 0 {
> > + cluster1_etf_out: endpoint {
> > + remote-endpoint =
> > + <&main_funnel_in_port1>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + cluster1_etf_in: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_funnel_out_port>;
> > + };
> > + };
> > + };
> > +
> > + main_funnel: funnel at 11005000 {
> > + compatible = "arm,coresight-funnel", "arm,primecell";
> > + reg = <0 0x11005000 0 0x1000>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port at 0 {
> > + reg = <0>;
> > + main_funnel_out_port: endpoint {
> > + remote-endpoint =
> > + <&soc_funnel_in_port>;
> > + };
> > + };
> > +
> > + port at 1 {
> > + reg = <0>;
> > + main_funnel_in_port0: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster0_etf_out>;
> > + };
> > + };
> > +
> > + port at 2 {
> > + reg = <1>;
> > + main_funnel_in_port1: endpoint {
> > + slave-mode;
> > + remote-endpoint =
> > + <&cluster1_etf_out>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + etm at 11440000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11440000 0 0x1000>;
> > + cpu = <&CPU0>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm0_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11540000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11540000 0 0x1000>;
> > + cpu = <&CPU1>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm1_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11640000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11640000 0 0x1000>;
> > + cpu = <&CPU2>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm2_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11740000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11740000 0 0x1000>;
> > + cpu = <&CPU3>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm3_out: endpoint {
> > + remote-endpoint =
> > + <&cluster0_funnel_in_port3>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11840000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11840000 0 0x1000>;
> > + cpu = <&CPU4>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm4_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port0>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11940000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11940000 0 0x1000>;
> > + cpu = <&CPU5>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm5_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port1>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11a40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11a40000 0 0x1000>;
> > + cpu = <&CPU6>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm6_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port2>;
> > + };
> > + };
> > + };
> > +
> > + etm at 11b40000 {
> > + compatible = "arm,coresight-etm4x", "arm,primecell";
> > + reg = <0 0x11b40000 0 0x1000>;
> > + cpu = <&CPU7>;
> > + clocks = <&ext_26m>;
> > + clock-names = "apb_pclk";
> > +
> > + port {
> > + etm7_out: endpoint {
> > + remote-endpoint =
> > + <&cluster1_funnel_in_port3>;
> > + };
> > + };
> > + };
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > new file mode 100644
> > index 0000000..5faa452
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
> > @@ -0,0 +1,56 @@
> > +/*
> > + * Spreadtrum SP9860g board DTS file
> > + *
> > + * Copyright (C) 2017, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "sc9860.dtsi"
> > +
> > +/ {
> > + model = "Spreadtrum SP9860G 3GFHD Board";
> > +
> > + compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> > +
> > + aliases {
> > + serial0 = &uart0; /* for Bluetooth */
> > + serial1 = &uart1; /* UART console */
> > + serial2 = &uart2; /* Reserved */
> > + serial3 = &uart3; /* for GPS */
> > + };
> > +
> > + memory{
> > + device_type = "memory";
> > + reg = <0x0 0x80000000 0 0x60000000>,
> > + <0x1 0x80000000 0 0x60000000>;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial1:115200n8";
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + status = "okay";
> > +};
> > +
> > +&uart3 {
> > + status = "okay";
> > +};
> > diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > new file mode 100644
> > index 0000000..64f06d9
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
> > @@ -0,0 +1,70 @@
> > +/*
> > + * Spreadtrum Whale2 SoC platform peripherals DTS file
> > + *
> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
> > + *
> > + * This file is licensed under a dual GPLv2 or X11 license.
> > + */
> > +
> > +/ {
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + soc: soc {
> > + compatible = "simple-bus";
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + ap-apb {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0 0x0 0x70000000 0x10000000>;
>
> Probably you should have 2 buses for each range of addresses.
I may not understand your point, I just looked at the SoC specification, the
address range of this AP APB bus is from 0x70000000 ~ 0x7fffffff.
>
> > +
> > + uart0: serial at 70000000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x000000 0x100>;
> > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart1: serial at 70100000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x100000 0x100>;
> > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial at 70200000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x200000 0x100>;
> > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > +
> > + uart3: serial at 70300000 {
> > + compatible = "sprd,sc9838-uart",
> > + "sprd,sc9836-uart";
> > + reg = <0x300000 0x100>;
> > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ext_26m>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > + ext_26m: ext-26m {
>
> This should be at the top-level. It is not part of the bus.
This clock node is in 'soc' node, not under 'ap-apb'. Since there're other
clocks on SC9860 which would have 'reg' property, we thought this fixed
clock would be better under 'soc' with other clocks.
Thanks your comments,
Chunyan
>
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <26000000>;
> > + clock-output-names = "ext_26m";
> > + };
> > + };
> > +};
> > --
> > 2.7.4
> >
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-24 15:07 ` Rob Herring
0 siblings, 0 replies; 48+ messages in thread
From: Rob Herring @ 2017-02-24 15:07 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Greg Kroah-Hartman, Catalin Marinas,
Will Deacon, Arnd Bergmann, Orson Zhai(翟京),
Sudeep Holla, linux-kernel, devicetree, linux-arm-kernel,
Lyra Zhang
On Fri, Feb 24, 2017 at 1:57 AM, Chunyan Zhang
<chunyan.zhang@spreadtrum.com> wrote:
> On 四, 2月 23, 2017 at 06:00:20下午 -0600, Rob Herring wrote:
>> On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
>> <chunyan.zhang@spreadtrum.com> wrote:
>> > From: Orson Zhai <orson.zhai@spreadtrum.com>
>> >
>> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>> >
>> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
>> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
>> > and sp9860g dts is for the board level.
>> >
>> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
>> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>> > ---
>> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
>> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
>> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
>> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
>> > 4 files changed, 659 insertions(+), 1 deletion(-)
>> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>> >
>> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
>> > index b658c5e..f0535e6 100644
>> > --- a/arch/arm64/boot/dts/sprd/Makefile
>> > +++ b/arch/arm64/boot/dts/sprd/Makefile
>> > @@ -1,4 +1,5 @@
>> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
>> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
>> > + sp9860g-1h10.dtb
>> >
>> > always := $(dtb-y)
>> > subdir-y := $(dts-dirs)
>> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > new file mode 100644
>> > index 0000000..73deb4e
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > @@ -0,0 +1,531 @@
>> > +/*
>> > + * Spreadtrum SP9860 SoC DTS file
>> > + *
>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>>
>> Please use SPDX-License-Identifier tag instead.
>>
>
> Just to double check, if I use it like:
>
> SPDX-License-Identifier: (GPL-2.0 or X11)
>
> Is this what you mean?
Yes. However, X11 is not actually correct (pretty much all dts files
have it wrong). This is the X11 license[1] which is explicitly for the
X Consortium and has a couple of extra clauses. While the MIT
license[2] is the text that most dts files actually use (while also
stating X11 license). It's obvious that everyone just copies and
pastes the license and has not consulted their lawyers.
> Will this file still be licensed under the same terms it was, right?
Consult your lawyer. :)
[...]
>> > + ext_26m: ext-26m {
>>
>> This should be at the top-level. It is not part of the bus.
>
> This clock node is in 'soc' node, not under 'ap-apb'. Since there're other
> clocks on SC9860 which would have 'reg' property, we thought this fixed
> clock would be better under 'soc' with other clocks.
But the clock is part of the board, not the soc. Or to put it another
way, it's not related to anything else, so it shouldn't be a child of
anything.
Rob
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-24 15:07 ` Rob Herring
0 siblings, 0 replies; 48+ messages in thread
From: Rob Herring @ 2017-02-24 15:07 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Greg Kroah-Hartman, Catalin Marinas,
Will Deacon, Arnd Bergmann, Orson Zhai(翟京),
Sudeep Holla, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Lyra Zhang
On Fri, Feb 24, 2017 at 1:57 AM, Chunyan Zhang
<chunyan.zhang-lxIno14LUO0EEoCn2XhGlw@public.gmane.org> wrote:
> On 四, 2月 23, 2017 at 06:00:20下午 -0600, Rob Herring wrote:
>> On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
>> <chunyan.zhang-lxIno14LUO0EEoCn2XhGlw@public.gmane.org> wrote:
>> > From: Orson Zhai <orson.zhai-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
>> >
>> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>> >
>> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
>> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
>> > and sp9860g dts is for the board level.
>> >
>> > Signed-off-by: Orson Zhai <orson.zhai-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
>> > Signed-off-by: Chunyan Zhang <chunyan.zhang-lxIno14LUO0EEoCn2XhGlw@public.gmane.org>
>> > ---
>> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
>> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
>> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
>> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
>> > 4 files changed, 659 insertions(+), 1 deletion(-)
>> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>> >
>> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
>> > index b658c5e..f0535e6 100644
>> > --- a/arch/arm64/boot/dts/sprd/Makefile
>> > +++ b/arch/arm64/boot/dts/sprd/Makefile
>> > @@ -1,4 +1,5 @@
>> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
>> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
>> > + sp9860g-1h10.dtb
>> >
>> > always := $(dtb-y)
>> > subdir-y := $(dts-dirs)
>> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > new file mode 100644
>> > index 0000000..73deb4e
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > @@ -0,0 +1,531 @@
>> > +/*
>> > + * Spreadtrum SP9860 SoC DTS file
>> > + *
>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>>
>> Please use SPDX-License-Identifier tag instead.
>>
>
> Just to double check, if I use it like:
>
> SPDX-License-Identifier: (GPL-2.0 or X11)
>
> Is this what you mean?
Yes. However, X11 is not actually correct (pretty much all dts files
have it wrong). This is the X11 license[1] which is explicitly for the
X Consortium and has a couple of extra clauses. While the MIT
license[2] is the text that most dts files actually use (while also
stating X11 license). It's obvious that everyone just copies and
pastes the license and has not consulted their lawyers.
> Will this file still be licensed under the same terms it was, right?
Consult your lawyer. :)
[...]
>> > + ext_26m: ext-26m {
>>
>> This should be at the top-level. It is not part of the bus.
>
> This clock node is in 'soc' node, not under 'ap-apb'. Since there're other
> clocks on SC9860 which would have 'reg' property, we thought this fixed
> clock would be better under 'soc' with other clocks.
But the clock is part of the board, not the soc. Or to put it another
way, it's not related to anything else, so it shouldn't be a child of
anything.
Rob
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-24 15:07 ` Rob Herring
0 siblings, 0 replies; 48+ messages in thread
From: Rob Herring @ 2017-02-24 15:07 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Feb 24, 2017 at 1:57 AM, Chunyan Zhang
<chunyan.zhang@spreadtrum.com> wrote:
> On ?, 2? 23, 2017 at 06:00:20?? -0600, Rob Herring wrote:
>> On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
>> <chunyan.zhang@spreadtrum.com> wrote:
>> > From: Orson Zhai <orson.zhai@spreadtrum.com>
>> >
>> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>> >
>> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
>> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
>> > and sp9860g dts is for the board level.
>> >
>> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
>> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>> > ---
>> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
>> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
>> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
>> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
>> > 4 files changed, 659 insertions(+), 1 deletion(-)
>> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>> >
>> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
>> > index b658c5e..f0535e6 100644
>> > --- a/arch/arm64/boot/dts/sprd/Makefile
>> > +++ b/arch/arm64/boot/dts/sprd/Makefile
>> > @@ -1,4 +1,5 @@
>> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
>> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
>> > + sp9860g-1h10.dtb
>> >
>> > always := $(dtb-y)
>> > subdir-y := $(dts-dirs)
>> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > new file mode 100644
>> > index 0000000..73deb4e
>> > --- /dev/null
>> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>> > @@ -0,0 +1,531 @@
>> > +/*
>> > + * Spreadtrum SP9860 SoC DTS file
>> > + *
>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>> > + *
>> > + * This file is licensed under a dual GPLv2 or X11 license.
>>
>> Please use SPDX-License-Identifier tag instead.
>>
>
> Just to double check, if I use it like:
>
> SPDX-License-Identifier: (GPL-2.0 or X11)
>
> Is this what you mean?
Yes. However, X11 is not actually correct (pretty much all dts files
have it wrong). This is the X11 license[1] which is explicitly for the
X Consortium and has a couple of extra clauses. While the MIT
license[2] is the text that most dts files actually use (while also
stating X11 license). It's obvious that everyone just copies and
pastes the license and has not consulted their lawyers.
> Will this file still be licensed under the same terms it was, right?
Consult your lawyer. :)
[...]
>> > + ext_26m: ext-26m {
>>
>> This should be at the top-level. It is not part of the bus.
>
> This clock node is in 'soc' node, not under 'ap-apb'. Since there're other
> clocks on SC9860 which would have 'reg' property, we thought this fixed
> clock would be better under 'soc' with other clocks.
But the clock is part of the board, not the soc. Or to put it another
way, it's not related to anything else, so it shouldn't be a child of
anything.
Rob
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 2/3] Documentation: sprd: Add bindings for SP9860G
2017-02-21 6:55 ` Chunyan Zhang
(?)
@ 2017-02-27 19:56 ` Rob Herring
-1 siblings, 0 replies; 48+ messages in thread
From: Rob Herring @ 2017-02-27 19:56 UTC (permalink / raw)
To: Chunyan Zhang
Cc: mark.rutland, gregkh, catalin.marinas, will.deacon, arnd,
orson.zhai, sudeep.holla, linux-kernel, devicetree,
linux-arm-kernel, zhang.lyra
On Tue, Feb 21, 2017 at 02:55:03PM +0800, Chunyan Zhang wrote:
> Added support for Spreadtrum SP9860G board and SC9860 SoC.
> This patch also revised bindings of SC9836 to make the format
> more clear.
>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> ---
> Documentation/devicetree/bindings/arm/sprd.txt | 13 ++++++++-----
> Documentation/devicetree/bindings/serial/sprd-uart.txt | 16 +++++++++++++++-
Probably should be 2 commits.
"dt-bindings: (arm|serial): " is the preferred subject prefix.
> 2 files changed, 23 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/arm/sprd.txt b/Documentation/devicetree/bindings/arm/sprd.txt
> index 31a629d..3df034b 100644
> --- a/Documentation/devicetree/bindings/arm/sprd.txt
> +++ b/Documentation/devicetree/bindings/arm/sprd.txt
> @@ -1,11 +1,14 @@
> Spreadtrum SoC Platforms Device Tree Bindings
> ----------------------------------------------------
>
> -Sharkl64 is a Spreadtrum's SoC Platform which is based
> -on ARM 64-bit processor.
> +SC9836 openphone Board
> +Required root node properties:
> + - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
>
> -SC9836 openphone board with SC9836 SoC based on the
> -Sharkl64 Platform shall have the following properties.
> +SC9860 SoC
> +Required root node properties:
> + - compatible = "sprd,sc9860"
>
> +SP9860G 3GFHD Board
> Required root node properties:
> - - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
> + - compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.txt b/Documentation/devicetree/bindings/serial/sprd-uart.txt
> index 2aff0f2..f530cbb 100644
> --- a/Documentation/devicetree/bindings/serial/sprd-uart.txt
> +++ b/Documentation/devicetree/bindings/serial/sprd-uart.txt
> @@ -1,7 +1,21 @@
> * Spreadtrum serial UART
>
> Required properties:
> -- compatible: must be "sprd,sc9836-uart"
> +- compatible must contain:
> + * "sprd,sc9836-uart" for SC9836 and all Spreadtrum SoCs
> + This also can be specific with:
> + * "sprd, sc9860-uart" for SC9860
space ^
> +
> - reg: offset and length of the register set for the device
> - interrupts: exactly one interrupt specifier
> - clocks: phandles to input clocks.
> +
> +Example:
> + uart0: serial@70000000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x000000 0x100>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
No need for status in examples.
> + };
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 2/3] Documentation: sprd: Add bindings for SP9860G
@ 2017-02-27 19:56 ` Rob Herring
0 siblings, 0 replies; 48+ messages in thread
From: Rob Herring @ 2017-02-27 19:56 UTC (permalink / raw)
To: Chunyan Zhang
Cc: mark.rutland, devicetree, orson.zhai, arnd, gregkh, sudeep.holla,
will.deacon, linux-kernel, zhang.lyra, catalin.marinas,
linux-arm-kernel
On Tue, Feb 21, 2017 at 02:55:03PM +0800, Chunyan Zhang wrote:
> Added support for Spreadtrum SP9860G board and SC9860 SoC.
> This patch also revised bindings of SC9836 to make the format
> more clear.
>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> ---
> Documentation/devicetree/bindings/arm/sprd.txt | 13 ++++++++-----
> Documentation/devicetree/bindings/serial/sprd-uart.txt | 16 +++++++++++++++-
Probably should be 2 commits.
"dt-bindings: (arm|serial): " is the preferred subject prefix.
> 2 files changed, 23 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/arm/sprd.txt b/Documentation/devicetree/bindings/arm/sprd.txt
> index 31a629d..3df034b 100644
> --- a/Documentation/devicetree/bindings/arm/sprd.txt
> +++ b/Documentation/devicetree/bindings/arm/sprd.txt
> @@ -1,11 +1,14 @@
> Spreadtrum SoC Platforms Device Tree Bindings
> ----------------------------------------------------
>
> -Sharkl64 is a Spreadtrum's SoC Platform which is based
> -on ARM 64-bit processor.
> +SC9836 openphone Board
> +Required root node properties:
> + - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
>
> -SC9836 openphone board with SC9836 SoC based on the
> -Sharkl64 Platform shall have the following properties.
> +SC9860 SoC
> +Required root node properties:
> + - compatible = "sprd,sc9860"
>
> +SP9860G 3GFHD Board
> Required root node properties:
> - - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
> + - compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.txt b/Documentation/devicetree/bindings/serial/sprd-uart.txt
> index 2aff0f2..f530cbb 100644
> --- a/Documentation/devicetree/bindings/serial/sprd-uart.txt
> +++ b/Documentation/devicetree/bindings/serial/sprd-uart.txt
> @@ -1,7 +1,21 @@
> * Spreadtrum serial UART
>
> Required properties:
> -- compatible: must be "sprd,sc9836-uart"
> +- compatible must contain:
> + * "sprd,sc9836-uart" for SC9836 and all Spreadtrum SoCs
> + This also can be specific with:
> + * "sprd, sc9860-uart" for SC9860
space ^
> +
> - reg: offset and length of the register set for the device
> - interrupts: exactly one interrupt specifier
> - clocks: phandles to input clocks.
> +
> +Example:
> + uart0: serial@70000000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x000000 0x100>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
No need for status in examples.
> + };
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 2/3] Documentation: sprd: Add bindings for SP9860G
@ 2017-02-27 19:56 ` Rob Herring
0 siblings, 0 replies; 48+ messages in thread
From: Rob Herring @ 2017-02-27 19:56 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Feb 21, 2017 at 02:55:03PM +0800, Chunyan Zhang wrote:
> Added support for Spreadtrum SP9860G board and SC9860 SoC.
> This patch also revised bindings of SC9836 to make the format
> more clear.
>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
> ---
> Documentation/devicetree/bindings/arm/sprd.txt | 13 ++++++++-----
> Documentation/devicetree/bindings/serial/sprd-uart.txt | 16 +++++++++++++++-
Probably should be 2 commits.
"dt-bindings: (arm|serial): " is the preferred subject prefix.
> 2 files changed, 23 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/arm/sprd.txt b/Documentation/devicetree/bindings/arm/sprd.txt
> index 31a629d..3df034b 100644
> --- a/Documentation/devicetree/bindings/arm/sprd.txt
> +++ b/Documentation/devicetree/bindings/arm/sprd.txt
> @@ -1,11 +1,14 @@
> Spreadtrum SoC Platforms Device Tree Bindings
> ----------------------------------------------------
>
> -Sharkl64 is a Spreadtrum's SoC Platform which is based
> -on ARM 64-bit processor.
> +SC9836 openphone Board
> +Required root node properties:
> + - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
>
> -SC9836 openphone board with SC9836 SoC based on the
> -Sharkl64 Platform shall have the following properties.
> +SC9860 SoC
> +Required root node properties:
> + - compatible = "sprd,sc9860"
>
> +SP9860G 3GFHD Board
> Required root node properties:
> - - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
> + - compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
> diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.txt b/Documentation/devicetree/bindings/serial/sprd-uart.txt
> index 2aff0f2..f530cbb 100644
> --- a/Documentation/devicetree/bindings/serial/sprd-uart.txt
> +++ b/Documentation/devicetree/bindings/serial/sprd-uart.txt
> @@ -1,7 +1,21 @@
> * Spreadtrum serial UART
>
> Required properties:
> -- compatible: must be "sprd,sc9836-uart"
> +- compatible must contain:
> + * "sprd,sc9836-uart" for SC9836 and all Spreadtrum SoCs
> + This also can be specific with:
> + * "sprd, sc9860-uart" for SC9860
space ^
> +
> - reg: offset and length of the register set for the device
> - interrupts: exactly one interrupt specifier
> - clocks: phandles to input clocks.
> +
> +Example:
> + uart0: serial at 70000000 {
> + compatible = "sprd,sc9838-uart",
> + "sprd,sc9836-uart";
> + reg = <0x000000 0x100>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
No need for status in examples.
> + };
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
2017-02-24 15:07 ` Rob Herring
(?)
@ 2017-02-28 7:08 ` Chunyan Zhang
-1 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-28 7:08 UTC (permalink / raw)
To: Rob Herring
Cc: Mark Rutland, Greg Kroah-Hartman, Catalin Marinas, Will Deacon,
Arnd Bergmann, Orson Zhai(翟京),
Sudeep Holla, linux-kernel, devicetree, linux-arm-kernel
On 24 February 2017 at 23:07, Rob Herring <robh+dt@kernel.org> wrote:
> On Fri, Feb 24, 2017 at 1:57 AM, Chunyan Zhang
> <chunyan.zhang@spreadtrum.com> wrote:
>> On 四, 2月 23, 2017 at 06:00:20下午 -0600, Rob Herring wrote:
>>> On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
>>> <chunyan.zhang@spreadtrum.com> wrote:
>>> > From: Orson Zhai <orson.zhai@spreadtrum.com>
>>> >
>>> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>>> >
>>> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
>>> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
>>> > and sp9860g dts is for the board level.
>>> >
>>> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
>>> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>>> > ---
>>> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
>>> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
>>> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
>>> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
>>> > 4 files changed, 659 insertions(+), 1 deletion(-)
>>> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
>>> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>>> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>>> >
>>> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
>>> > index b658c5e..f0535e6 100644
>>> > --- a/arch/arm64/boot/dts/sprd/Makefile
>>> > +++ b/arch/arm64/boot/dts/sprd/Makefile
>>> > @@ -1,4 +1,5 @@
>>> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
>>> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
>>> > + sp9860g-1h10.dtb
>>> >
>>> > always := $(dtb-y)
>>> > subdir-y := $(dts-dirs)
>>> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>>> > new file mode 100644
>>> > index 0000000..73deb4e
>>> > --- /dev/null
>>> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>>> > @@ -0,0 +1,531 @@
>>> > +/*
>>> > + * Spreadtrum SP9860 SoC DTS file
>>> > + *
>>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>>> > + *
>>> > + * This file is licensed under a dual GPLv2 or X11 license.
>>>
>>> Please use SPDX-License-Identifier tag instead.
>>>
>>
>> Just to double check, if I use it like:
>>
>> SPDX-License-Identifier: (GPL-2.0 or X11)
>>
>> Is this what you mean?
>
> Yes. However, X11 is not actually correct (pretty much all dts files
> have it wrong). This is the X11 license[1] which is explicitly for the
> X Consortium and has a couple of extra clauses. While the MIT
> license[2] is the text that most dts files actually use (while also
> stating X11 license). It's obvious that everyone just copies and
> pastes the license and has not consulted their lawyers.
OK, got it.
>
>> Will this file still be licensed under the same terms it was, right?
>
> Consult your lawyer. :)
>
> [...]
>
>>> > + ext_26m: ext-26m {
>>>
>>> This should be at the top-level. It is not part of the bus.
>>
>> This clock node is in 'soc' node, not under 'ap-apb'. Since there're other
>> clocks on SC9860 which would have 'reg' property, we thought this fixed
>> clock would be better under 'soc' with other clocks.
>
> But the clock is part of the board, not the soc. Or to put it another
> way, it's not related to anything else, so it shouldn't be a child of
> anything.
Ok, I will move it to the top-level.
Thanks,
Chunyan
>
> Rob
>
> [1] https://spdx.org/licenses/X11.html
> [2] https://spdx.org/licenses/MIT.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-28 7:08 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-28 7:08 UTC (permalink / raw)
To: Rob Herring
Cc: Mark Rutland, devicetree, Orson Zhai(翟京),
Arnd Bergmann, Greg Kroah-Hartman, Sudeep Holla, Will Deacon,
linux-kernel, Catalin Marinas, linux-arm-kernel
On 24 February 2017 at 23:07, Rob Herring <robh+dt@kernel.org> wrote:
> On Fri, Feb 24, 2017 at 1:57 AM, Chunyan Zhang
> <chunyan.zhang@spreadtrum.com> wrote:
>> On 四, 2月 23, 2017 at 06:00:20下午 -0600, Rob Herring wrote:
>>> On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
>>> <chunyan.zhang@spreadtrum.com> wrote:
>>> > From: Orson Zhai <orson.zhai@spreadtrum.com>
>>> >
>>> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>>> >
>>> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
>>> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
>>> > and sp9860g dts is for the board level.
>>> >
>>> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
>>> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>>> > ---
>>> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
>>> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
>>> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
>>> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
>>> > 4 files changed, 659 insertions(+), 1 deletion(-)
>>> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
>>> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>>> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>>> >
>>> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
>>> > index b658c5e..f0535e6 100644
>>> > --- a/arch/arm64/boot/dts/sprd/Makefile
>>> > +++ b/arch/arm64/boot/dts/sprd/Makefile
>>> > @@ -1,4 +1,5 @@
>>> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
>>> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
>>> > + sp9860g-1h10.dtb
>>> >
>>> > always := $(dtb-y)
>>> > subdir-y := $(dts-dirs)
>>> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>>> > new file mode 100644
>>> > index 0000000..73deb4e
>>> > --- /dev/null
>>> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>>> > @@ -0,0 +1,531 @@
>>> > +/*
>>> > + * Spreadtrum SP9860 SoC DTS file
>>> > + *
>>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>>> > + *
>>> > + * This file is licensed under a dual GPLv2 or X11 license.
>>>
>>> Please use SPDX-License-Identifier tag instead.
>>>
>>
>> Just to double check, if I use it like:
>>
>> SPDX-License-Identifier: (GPL-2.0 or X11)
>>
>> Is this what you mean?
>
> Yes. However, X11 is not actually correct (pretty much all dts files
> have it wrong). This is the X11 license[1] which is explicitly for the
> X Consortium and has a couple of extra clauses. While the MIT
> license[2] is the text that most dts files actually use (while also
> stating X11 license). It's obvious that everyone just copies and
> pastes the license and has not consulted their lawyers.
OK, got it.
>
>> Will this file still be licensed under the same terms it was, right?
>
> Consult your lawyer. :)
>
> [...]
>
>>> > + ext_26m: ext-26m {
>>>
>>> This should be at the top-level. It is not part of the bus.
>>
>> This clock node is in 'soc' node, not under 'ap-apb'. Since there're other
>> clocks on SC9860 which would have 'reg' property, we thought this fixed
>> clock would be better under 'soc' with other clocks.
>
> But the clock is part of the board, not the soc. Or to put it another
> way, it's not related to anything else, so it shouldn't be a child of
> anything.
Ok, I will move it to the top-level.
Thanks,
Chunyan
>
> Rob
>
> [1] https://spdx.org/licenses/X11.html
> [2] https://spdx.org/licenses/MIT.html
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G
@ 2017-02-28 7:08 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-28 7:08 UTC (permalink / raw)
To: linux-arm-kernel
On 24 February 2017 at 23:07, Rob Herring <robh+dt@kernel.org> wrote:
> On Fri, Feb 24, 2017 at 1:57 AM, Chunyan Zhang
> <chunyan.zhang@spreadtrum.com> wrote:
>> On ?, 2? 23, 2017 at 06:00:20?? -0600, Rob Herring wrote:
>>> On Tue, Feb 21, 2017 at 12:55 AM, Chunyan Zhang
>>> <chunyan.zhang@spreadtrum.com> wrote:
>>> > From: Orson Zhai <orson.zhai@spreadtrum.com>
>>> >
>>> > SC9860G is a 8 cores of A53 SoC with 4G LTE support SoC from Spreadtrum.
>>> >
>>> > According to regular hierarchy of sprd dts, whale2.dtsi contains SoC
>>> > peripherals IP nodes, sc9860.dtsi contains stuff related to ARM core stuff
>>> > and sp9860g dts is for the board level.
>>> >
>>> > Signed-off-by: Orson Zhai <orson.zhai@spreadtrum.com>
>>> > Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>>> > ---
>>> > arch/arm64/boot/dts/sprd/Makefile | 3 +-
>>> > arch/arm64/boot/dts/sprd/sc9860.dtsi | 531 ++++++++++++++++++++++++++++++
>>> > arch/arm64/boot/dts/sprd/sp9860g-1h10.dts | 56 ++++
>>> > arch/arm64/boot/dts/sprd/whale2.dtsi | 70 ++++
>>> > 4 files changed, 659 insertions(+), 1 deletion(-)
>>> > create mode 100644 arch/arm64/boot/dts/sprd/sc9860.dtsi
>>> > create mode 100644 arch/arm64/boot/dts/sprd/sp9860g-1h10.dts
>>> > create mode 100644 arch/arm64/boot/dts/sprd/whale2.dtsi
>>> >
>>> > diff --git a/arch/arm64/boot/dts/sprd/Makefile b/arch/arm64/boot/dts/sprd/Makefile
>>> > index b658c5e..f0535e6 100644
>>> > --- a/arch/arm64/boot/dts/sprd/Makefile
>>> > +++ b/arch/arm64/boot/dts/sprd/Makefile
>>> > @@ -1,4 +1,5 @@
>>> > -dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb
>>> > +dtb-$(CONFIG_ARCH_SPRD) += sc9836-openphone.dtb \
>>> > + sp9860g-1h10.dtb
>>> >
>>> > always := $(dtb-y)
>>> > subdir-y := $(dts-dirs)
>>> > diff --git a/arch/arm64/boot/dts/sprd/sc9860.dtsi b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>>> > new file mode 100644
>>> > index 0000000..73deb4e
>>> > --- /dev/null
>>> > +++ b/arch/arm64/boot/dts/sprd/sc9860.dtsi
>>> > @@ -0,0 +1,531 @@
>>> > +/*
>>> > + * Spreadtrum SP9860 SoC DTS file
>>> > + *
>>> > + * Copyright (C) 2016, Spreadtrum Communications Inc.
>>> > + *
>>> > + * This file is licensed under a dual GPLv2 or X11 license.
>>>
>>> Please use SPDX-License-Identifier tag instead.
>>>
>>
>> Just to double check, if I use it like:
>>
>> SPDX-License-Identifier: (GPL-2.0 or X11)
>>
>> Is this what you mean?
>
> Yes. However, X11 is not actually correct (pretty much all dts files
> have it wrong). This is the X11 license[1] which is explicitly for the
> X Consortium and has a couple of extra clauses. While the MIT
> license[2] is the text that most dts files actually use (while also
> stating X11 license). It's obvious that everyone just copies and
> pastes the license and has not consulted their lawyers.
OK, got it.
>
>> Will this file still be licensed under the same terms it was, right?
>
> Consult your lawyer. :)
>
> [...]
>
>>> > + ext_26m: ext-26m {
>>>
>>> This should be at the top-level. It is not part of the bus.
>>
>> This clock node is in 'soc' node, not under 'ap-apb'. Since there're other
>> clocks on SC9860 which would have 'reg' property, we thought this fixed
>> clock would be better under 'soc' with other clocks.
>
> But the clock is part of the board, not the soc. Or to put it another
> way, it's not related to anything else, so it shouldn't be a child of
> anything.
Ok, I will move it to the top-level.
Thanks,
Chunyan
>
> Rob
>
> [1] https://spdx.org/licenses/X11.html
> [2] https://spdx.org/licenses/MIT.html
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 2/3] Documentation: sprd: Add bindings for SP9860G
2017-02-27 19:56 ` Rob Herring
(?)
@ 2017-02-28 9:14 ` Chunyan Zhang
-1 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-28 9:14 UTC (permalink / raw)
To: Rob Herring
Cc: Chunyan Zhang, Mark Rutland, gregkh, Catalin Marinas,
Will Deacon, Arnd Bergmann, Orson Zhai (翟京),
Sudeep Holla, linux-kernel, devicetree, linux-arm-kernel
On 28 February 2017 at 03:56, Rob Herring <robh@kernel.org> wrote:
> On Tue, Feb 21, 2017 at 02:55:03PM +0800, Chunyan Zhang wrote:
>> Added support for Spreadtrum SP9860G board and SC9860 SoC.
>> This patch also revised bindings of SC9836 to make the format
>> more clear.
>>
>> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>> ---
>> Documentation/devicetree/bindings/arm/sprd.txt | 13 ++++++++-----
>> Documentation/devicetree/bindings/serial/sprd-uart.txt | 16 +++++++++++++++-
>
> Probably should be 2 commits.
>
> "dt-bindings: (arm|serial): " is the preferred subject prefix.
Ok, will do.
Thanks,
Chunyan
>
>> 2 files changed, 23 insertions(+), 6 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/sprd.txt b/Documentation/devicetree/bindings/arm/sprd.txt
>> index 31a629d..3df034b 100644
>> --- a/Documentation/devicetree/bindings/arm/sprd.txt
>> +++ b/Documentation/devicetree/bindings/arm/sprd.txt
>> @@ -1,11 +1,14 @@
>> Spreadtrum SoC Platforms Device Tree Bindings
>> ----------------------------------------------------
>>
>> -Sharkl64 is a Spreadtrum's SoC Platform which is based
>> -on ARM 64-bit processor.
>> +SC9836 openphone Board
>> +Required root node properties:
>> + - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
>>
>> -SC9836 openphone board with SC9836 SoC based on the
>> -Sharkl64 Platform shall have the following properties.
>> +SC9860 SoC
>> +Required root node properties:
>> + - compatible = "sprd,sc9860"
>>
>> +SP9860G 3GFHD Board
>> Required root node properties:
>> - - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
>> + - compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
>> diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.txt b/Documentation/devicetree/bindings/serial/sprd-uart.txt
>> index 2aff0f2..f530cbb 100644
>> --- a/Documentation/devicetree/bindings/serial/sprd-uart.txt
>> +++ b/Documentation/devicetree/bindings/serial/sprd-uart.txt
>> @@ -1,7 +1,21 @@
>> * Spreadtrum serial UART
>>
>> Required properties:
>> -- compatible: must be "sprd,sc9836-uart"
>> +- compatible must contain:
>> + * "sprd,sc9836-uart" for SC9836 and all Spreadtrum SoCs
>> + This also can be specific with:
>> + * "sprd, sc9860-uart" for SC9860
> space ^
>
>> +
>> - reg: offset and length of the register set for the device
>> - interrupts: exactly one interrupt specifier
>> - clocks: phandles to input clocks.
>> +
>> +Example:
>> + uart0: serial@70000000 {
>> + compatible = "sprd,sc9838-uart",
>> + "sprd,sc9836-uart";
>> + reg = <0x000000 0x100>;
>> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ext_26m>;
>> + status = "disabled";
>
> No need for status in examples.
>
>> + };
>> --
>> 2.7.4
>>
^ permalink raw reply [flat|nested] 48+ messages in thread
* Re: [PATCH V2 2/3] Documentation: sprd: Add bindings for SP9860G
@ 2017-02-28 9:14 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-28 9:14 UTC (permalink / raw)
To: Rob Herring
Cc: Mark Rutland, devicetree, Orson Zhai (翟京),
Arnd Bergmann, gregkh, Sudeep Holla, Will Deacon, linux-kernel,
Catalin Marinas, Chunyan Zhang, linux-arm-kernel
On 28 February 2017 at 03:56, Rob Herring <robh@kernel.org> wrote:
> On Tue, Feb 21, 2017 at 02:55:03PM +0800, Chunyan Zhang wrote:
>> Added support for Spreadtrum SP9860G board and SC9860 SoC.
>> This patch also revised bindings of SC9836 to make the format
>> more clear.
>>
>> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>> ---
>> Documentation/devicetree/bindings/arm/sprd.txt | 13 ++++++++-----
>> Documentation/devicetree/bindings/serial/sprd-uart.txt | 16 +++++++++++++++-
>
> Probably should be 2 commits.
>
> "dt-bindings: (arm|serial): " is the preferred subject prefix.
Ok, will do.
Thanks,
Chunyan
>
>> 2 files changed, 23 insertions(+), 6 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/sprd.txt b/Documentation/devicetree/bindings/arm/sprd.txt
>> index 31a629d..3df034b 100644
>> --- a/Documentation/devicetree/bindings/arm/sprd.txt
>> +++ b/Documentation/devicetree/bindings/arm/sprd.txt
>> @@ -1,11 +1,14 @@
>> Spreadtrum SoC Platforms Device Tree Bindings
>> ----------------------------------------------------
>>
>> -Sharkl64 is a Spreadtrum's SoC Platform which is based
>> -on ARM 64-bit processor.
>> +SC9836 openphone Board
>> +Required root node properties:
>> + - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
>>
>> -SC9836 openphone board with SC9836 SoC based on the
>> -Sharkl64 Platform shall have the following properties.
>> +SC9860 SoC
>> +Required root node properties:
>> + - compatible = "sprd,sc9860"
>>
>> +SP9860G 3GFHD Board
>> Required root node properties:
>> - - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
>> + - compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
>> diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.txt b/Documentation/devicetree/bindings/serial/sprd-uart.txt
>> index 2aff0f2..f530cbb 100644
>> --- a/Documentation/devicetree/bindings/serial/sprd-uart.txt
>> +++ b/Documentation/devicetree/bindings/serial/sprd-uart.txt
>> @@ -1,7 +1,21 @@
>> * Spreadtrum serial UART
>>
>> Required properties:
>> -- compatible: must be "sprd,sc9836-uart"
>> +- compatible must contain:
>> + * "sprd,sc9836-uart" for SC9836 and all Spreadtrum SoCs
>> + This also can be specific with:
>> + * "sprd, sc9860-uart" for SC9860
> space ^
>
>> +
>> - reg: offset and length of the register set for the device
>> - interrupts: exactly one interrupt specifier
>> - clocks: phandles to input clocks.
>> +
>> +Example:
>> + uart0: serial@70000000 {
>> + compatible = "sprd,sc9838-uart",
>> + "sprd,sc9836-uart";
>> + reg = <0x000000 0x100>;
>> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ext_26m>;
>> + status = "disabled";
>
> No need for status in examples.
>
>> + };
>> --
>> 2.7.4
>>
^ permalink raw reply [flat|nested] 48+ messages in thread
* [PATCH V2 2/3] Documentation: sprd: Add bindings for SP9860G
@ 2017-02-28 9:14 ` Chunyan Zhang
0 siblings, 0 replies; 48+ messages in thread
From: Chunyan Zhang @ 2017-02-28 9:14 UTC (permalink / raw)
To: linux-arm-kernel
On 28 February 2017 at 03:56, Rob Herring <robh@kernel.org> wrote:
> On Tue, Feb 21, 2017 at 02:55:03PM +0800, Chunyan Zhang wrote:
>> Added support for Spreadtrum SP9860G board and SC9860 SoC.
>> This patch also revised bindings of SC9836 to make the format
>> more clear.
>>
>> Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
>> ---
>> Documentation/devicetree/bindings/arm/sprd.txt | 13 ++++++++-----
>> Documentation/devicetree/bindings/serial/sprd-uart.txt | 16 +++++++++++++++-
>
> Probably should be 2 commits.
>
> "dt-bindings: (arm|serial): " is the preferred subject prefix.
Ok, will do.
Thanks,
Chunyan
>
>> 2 files changed, 23 insertions(+), 6 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/sprd.txt b/Documentation/devicetree/bindings/arm/sprd.txt
>> index 31a629d..3df034b 100644
>> --- a/Documentation/devicetree/bindings/arm/sprd.txt
>> +++ b/Documentation/devicetree/bindings/arm/sprd.txt
>> @@ -1,11 +1,14 @@
>> Spreadtrum SoC Platforms Device Tree Bindings
>> ----------------------------------------------------
>>
>> -Sharkl64 is a Spreadtrum's SoC Platform which is based
>> -on ARM 64-bit processor.
>> +SC9836 openphone Board
>> +Required root node properties:
>> + - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
>>
>> -SC9836 openphone board with SC9836 SoC based on the
>> -Sharkl64 Platform shall have the following properties.
>> +SC9860 SoC
>> +Required root node properties:
>> + - compatible = "sprd,sc9860"
>>
>> +SP9860G 3GFHD Board
>> Required root node properties:
>> - - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
>> + - compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
>> diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.txt b/Documentation/devicetree/bindings/serial/sprd-uart.txt
>> index 2aff0f2..f530cbb 100644
>> --- a/Documentation/devicetree/bindings/serial/sprd-uart.txt
>> +++ b/Documentation/devicetree/bindings/serial/sprd-uart.txt
>> @@ -1,7 +1,21 @@
>> * Spreadtrum serial UART
>>
>> Required properties:
>> -- compatible: must be "sprd,sc9836-uart"
>> +- compatible must contain:
>> + * "sprd,sc9836-uart" for SC9836 and all Spreadtrum SoCs
>> + This also can be specific with:
>> + * "sprd, sc9860-uart" for SC9860
> space ^
>
>> +
>> - reg: offset and length of the register set for the device
>> - interrupts: exactly one interrupt specifier
>> - clocks: phandles to input clocks.
>> +
>> +Example:
>> + uart0: serial at 70000000 {
>> + compatible = "sprd,sc9838-uart",
>> + "sprd,sc9836-uart";
>> + reg = <0x000000 0x100>;
>> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ext_26m>;
>> + status = "disabled";
>
> No need for status in examples.
>
>> + };
>> --
>> 2.7.4
>>
^ permalink raw reply [flat|nested] 48+ messages in thread
end of thread, other threads:[~2017-02-28 10:23 UTC | newest]
Thread overview: 48+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-02-21 6:55 [PATCH V2 0/3] Add Spreadtrum SP9860G support Chunyan Zhang
2017-02-21 6:55 ` Chunyan Zhang
2017-02-21 6:55 ` Chunyan Zhang
2017-02-21 6:55 ` [PATCH V2 1/3] arm64: dts: Add basic DT to support Spreadtrum's SP9860G Chunyan Zhang
2017-02-21 6:55 ` Chunyan Zhang
2017-02-21 6:55 ` Chunyan Zhang
2017-02-21 10:57 ` Sudeep Holla
2017-02-21 10:57 ` Sudeep Holla
2017-02-21 10:57 ` Sudeep Holla
2017-02-21 16:27 ` Mathieu Poirier
2017-02-21 16:27 ` Mathieu Poirier
2017-02-21 16:27 ` Mathieu Poirier
2017-02-22 3:46 ` Chunyan Zhang
2017-02-22 3:46 ` Chunyan Zhang
2017-02-22 3:46 ` Chunyan Zhang
2017-02-22 16:02 ` Mathieu Poirier
2017-02-22 16:02 ` Mathieu Poirier
2017-02-22 16:02 ` Mathieu Poirier
2017-02-23 6:20 ` Chunyan Zhang
2017-02-23 6:20 ` Chunyan Zhang
2017-02-23 6:20 ` Chunyan Zhang
2017-02-23 10:56 ` Sudeep Holla
2017-02-23 10:56 ` Sudeep Holla
2017-02-23 10:56 ` Sudeep Holla
2017-02-24 0:00 ` Rob Herring
2017-02-24 0:00 ` Rob Herring
2017-02-24 0:00 ` Rob Herring
2017-02-24 7:57 ` Chunyan Zhang
2017-02-24 7:57 ` Chunyan Zhang
2017-02-24 7:57 ` Chunyan Zhang
2017-02-24 15:07 ` Rob Herring
2017-02-24 15:07 ` Rob Herring
2017-02-24 15:07 ` Rob Herring
2017-02-28 7:08 ` Chunyan Zhang
2017-02-28 7:08 ` Chunyan Zhang
2017-02-28 7:08 ` Chunyan Zhang
2017-02-21 6:55 ` [PATCH V2 2/3] Documentation: sprd: Add bindings for SP9860G Chunyan Zhang
2017-02-21 6:55 ` Chunyan Zhang
2017-02-21 6:55 ` Chunyan Zhang
2017-02-27 19:56 ` Rob Herring
2017-02-27 19:56 ` Rob Herring
2017-02-27 19:56 ` Rob Herring
2017-02-28 9:14 ` Chunyan Zhang
2017-02-28 9:14 ` Chunyan Zhang
2017-02-28 9:14 ` Chunyan Zhang
2017-02-21 6:55 ` [PATCH V2 3/3] serial: sprd: adjust TIMEOUT to a big value Chunyan Zhang
2017-02-21 6:55 ` Chunyan Zhang
2017-02-21 6:55 ` Chunyan Zhang
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.