* [PATCH] arm64: dts: updated sata node on ls1012a dts
@ 2017-03-10 8:12 ` Yuantian Tang
0 siblings, 0 replies; 4+ messages in thread
From: Yuantian Tang @ 2017-03-10 8:12 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Yuantian Tang
On ls1012a soc, sata ecc should be disabled. So added sata ecc
register address so that driver can get this information.
Signed-off-by: Tang Yuantian <andy.tang-3arQi8VN3Tc@public.gmane.org>
---
arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 80 +++++++++++++++++++++++++-
1 file changed, 79 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
index cffebb4..1870dde 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
@@ -43,6 +43,7 @@
*/
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/thermal/thermal.h>
/ {
compatible = "fsl,ls1012a";
@@ -126,6 +127,81 @@
#clock-cells = <2>;
clocks = <&sysclk>;
};
+ tmu: tmu@1f00000 {
+ compatible = "fsl,qoriq-tmu";
+ reg = <0x0 0x1f00000 0x0 0x10000>;
+ interrupts = <0 33 0x4>;
+ fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
+ fsl,tmu-calibration = <0x00000000 0x00000026
+ 0x00000001 0x0000002d
+ 0x00000002 0x00000032
+ 0x00000003 0x00000039
+ 0x00000004 0x0000003f
+ 0x00000005 0x00000046
+ 0x00000006 0x0000004d
+ 0x00000007 0x00000054
+ 0x00000008 0x0000005a
+ 0x00000009 0x00000061
+ 0x0000000a 0x0000006a
+ 0x0000000b 0x00000071
+
+ 0x00010000 0x00000025
+ 0x00010001 0x0000002c
+ 0x00010002 0x00000035
+ 0x00010003 0x0000003d
+ 0x00010004 0x00000045
+ 0x00010005 0x0000004e
+ 0x00010006 0x00000057
+ 0x00010007 0x00000061
+ 0x00010008 0x0000006b
+ 0x00010009 0x00000076
+
+ 0x00020000 0x00000029
+ 0x00020001 0x00000033
+ 0x00020002 0x0000003d
+ 0x00020003 0x00000049
+ 0x00020004 0x00000056
+ 0x00020005 0x00000061
+ 0x00020006 0x0000006d
+
+ 0x00030000 0x00000021
+ 0x00030001 0x0000002a
+ 0x00030002 0x0000003c
+ 0x00030003 0x0000004e>;
+ big-endian;
+ #thermal-sensor-cells = <1>;
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <1000>;
+ polling-delay = <5000>;
+
+ thermal-sensors = <&tmu 0>;
+
+ trips {
+ cpu_alert: cpu-alert {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit: cpu-crit {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert>;
+ cooling-device =
+ <&cpu0 THERMAL_NO_LIMIT
+ THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
i2c0: i2c@2180000 {
compatible = "fsl,vf610-i2c";
@@ -238,7 +314,9 @@
sata: sata@3200000 {
compatible = "fsl,ls1012a-ahci", "fsl,ls1043a-ahci";
- reg = <0x0 0x3200000 0x0 0x10000>;
+ reg = <0x0 0x3200000 0x0 0x10000>,
+ <0x0 0x20140520 0x0 0x4>;
+ reg-names = "ahci", "sata-ecc";
interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clockgen 4 0>;
status = "disabled";
--
2.1.0.27.g96db324
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH] arm64: dts: updated sata node on ls1012a dts
@ 2017-03-10 8:12 ` Yuantian Tang
0 siblings, 0 replies; 4+ messages in thread
From: Yuantian Tang @ 2017-03-10 8:12 UTC (permalink / raw)
To: linux-arm-kernel
On ls1012a soc, sata ecc should be disabled. So added sata ecc
register address so that driver can get this information.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
---
arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 80 +++++++++++++++++++++++++-
1 file changed, 79 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
index cffebb4..1870dde 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
@@ -43,6 +43,7 @@
*/
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/thermal/thermal.h>
/ {
compatible = "fsl,ls1012a";
@@ -126,6 +127,81 @@
#clock-cells = <2>;
clocks = <&sysclk>;
};
+ tmu: tmu at 1f00000 {
+ compatible = "fsl,qoriq-tmu";
+ reg = <0x0 0x1f00000 0x0 0x10000>;
+ interrupts = <0 33 0x4>;
+ fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
+ fsl,tmu-calibration = <0x00000000 0x00000026
+ 0x00000001 0x0000002d
+ 0x00000002 0x00000032
+ 0x00000003 0x00000039
+ 0x00000004 0x0000003f
+ 0x00000005 0x00000046
+ 0x00000006 0x0000004d
+ 0x00000007 0x00000054
+ 0x00000008 0x0000005a
+ 0x00000009 0x00000061
+ 0x0000000a 0x0000006a
+ 0x0000000b 0x00000071
+
+ 0x00010000 0x00000025
+ 0x00010001 0x0000002c
+ 0x00010002 0x00000035
+ 0x00010003 0x0000003d
+ 0x00010004 0x00000045
+ 0x00010005 0x0000004e
+ 0x00010006 0x00000057
+ 0x00010007 0x00000061
+ 0x00010008 0x0000006b
+ 0x00010009 0x00000076
+
+ 0x00020000 0x00000029
+ 0x00020001 0x00000033
+ 0x00020002 0x0000003d
+ 0x00020003 0x00000049
+ 0x00020004 0x00000056
+ 0x00020005 0x00000061
+ 0x00020006 0x0000006d
+
+ 0x00030000 0x00000021
+ 0x00030001 0x0000002a
+ 0x00030002 0x0000003c
+ 0x00030003 0x0000004e>;
+ big-endian;
+ #thermal-sensor-cells = <1>;
+ };
+
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <1000>;
+ polling-delay = <5000>;
+
+ thermal-sensors = <&tmu 0>;
+
+ trips {
+ cpu_alert: cpu-alert {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit: cpu-crit {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert>;
+ cooling-device =
+ <&cpu0 THERMAL_NO_LIMIT
+ THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+ };
i2c0: i2c at 2180000 {
compatible = "fsl,vf610-i2c";
@@ -238,7 +314,9 @@
sata: sata at 3200000 {
compatible = "fsl,ls1012a-ahci", "fsl,ls1043a-ahci";
- reg = <0x0 0x3200000 0x0 0x10000>;
+ reg = <0x0 0x3200000 0x0 0x10000>,
+ <0x0 0x20140520 0x0 0x4>;
+ reg-names = "ahci", "sata-ecc";
interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clockgen 4 0>;
status = "disabled";
--
2.1.0.27.g96db324
^ permalink raw reply related [flat|nested] 4+ messages in thread
* RE: [PATCH] arm64: dts: updated sata node on ls1012a dts
2017-03-10 8:12 ` Yuantian Tang
@ 2017-03-10 8:27 ` Andy Tang
-1 siblings, 0 replies; 4+ messages in thread
From: Andy Tang @ 2017-03-10 8:27 UTC (permalink / raw)
To: Andy Tang, shawnguo-DgEjT+Ai2ygdnm+yROfE0A
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
catalin.marinas-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Please ignore it. Send the wrong patch.
Sorry about it.
Regards,
Yuantian
> -----Original Message-----
> From: Yuantian Tang [mailto:andy.tang-3arQi8VN3Tc@public.gmane.org]
> Sent: Friday, March 10, 2017 4:12 PM
> To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org
> Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org; mark.rutland-5wv7dgnIgG8@public.gmane.org; catalin.marinas-5wv7dgnIgG8@public.gmane.org;
> will.deacon-5wv7dgnIgG8@public.gmane.org; devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-arm-
> kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org; Andy Tang
> Subject: [PATCH] arm64: dts: updated sata node on ls1012a dts
>
> On ls1012a soc, sata ecc should be disabled. So added sata ecc register
> address so that driver can get this information.
>
> Signed-off-by: Tang Yuantian <andy.tang-3arQi8VN3Tc@public.gmane.org>
> ---
> arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 80
> +++++++++++++++++++++++++-
> 1 file changed, 79 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> index cffebb4..1870dde 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> @@ -43,6 +43,7 @@
> */
>
> #include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/thermal/thermal.h>
>
> / {
> compatible = "fsl,ls1012a";
> @@ -126,6 +127,81 @@
> #clock-cells = <2>;
> clocks = <&sysclk>;
> };
> + tmu: tmu@1f00000 {
> + compatible = "fsl,qoriq-tmu";
> + reg = <0x0 0x1f00000 0x0 0x10000>;
> + interrupts = <0 33 0x4>;
> + fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
> + fsl,tmu-calibration = <0x00000000 0x00000026
> + 0x00000001 0x0000002d
> + 0x00000002 0x00000032
> + 0x00000003 0x00000039
> + 0x00000004 0x0000003f
> + 0x00000005 0x00000046
> + 0x00000006 0x0000004d
> + 0x00000007 0x00000054
> + 0x00000008 0x0000005a
> + 0x00000009 0x00000061
> + 0x0000000a 0x0000006a
> + 0x0000000b 0x00000071
> +
> + 0x00010000 0x00000025
> + 0x00010001 0x0000002c
> + 0x00010002 0x00000035
> + 0x00010003 0x0000003d
> + 0x00010004 0x00000045
> + 0x00010005 0x0000004e
> + 0x00010006 0x00000057
> + 0x00010007 0x00000061
> + 0x00010008 0x0000006b
> + 0x00010009 0x00000076
> +
> + 0x00020000 0x00000029
> + 0x00020001 0x00000033
> + 0x00020002 0x0000003d
> + 0x00020003 0x00000049
> + 0x00020004 0x00000056
> + 0x00020005 0x00000061
> + 0x00020006 0x0000006d
> +
> + 0x00030000 0x00000021
> + 0x00030001 0x0000002a
> + 0x00030002 0x0000003c
> + 0x00030003 0x0000004e>;
> + big-endian;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + thermal-zones {
> + cpu_thermal: cpu-thermal {
> + polling-delay-passive = <1000>;
> + polling-delay = <5000>;
> +
> + thermal-sensors = <&tmu 0>;
> +
> + trips {
> + cpu_alert: cpu-alert {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + cpu_crit: cpu-crit {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu_alert>;
> + cooling-device =
> + <&cpu0
> THERMAL_NO_LIMIT
> +
> THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> + };
>
> i2c0: i2c@2180000 {
> compatible = "fsl,vf610-i2c";
> @@ -238,7 +314,9 @@
>
> sata: sata@3200000 {
> compatible = "fsl,ls1012a-ahci", "fsl,ls1043a-ahci";
> - reg = <0x0 0x3200000 0x0 0x10000>;
> + reg = <0x0 0x3200000 0x0 0x10000>,
> + <0x0 0x20140520 0x0 0x4>;
> + reg-names = "ahci", "sata-ecc";
> interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clockgen 4 0>;
> status = "disabled";
> --
> 2.1.0.27.g96db324
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH] arm64: dts: updated sata node on ls1012a dts
@ 2017-03-10 8:27 ` Andy Tang
0 siblings, 0 replies; 4+ messages in thread
From: Andy Tang @ 2017-03-10 8:27 UTC (permalink / raw)
To: linux-arm-kernel
Please ignore it. Send the wrong patch.
Sorry about it.
Regards,
Yuantian
> -----Original Message-----
> From: Yuantian Tang [mailto:andy.tang at nxp.com]
> Sent: Friday, March 10, 2017 4:12 PM
> To: shawnguo at kernel.org
> Cc: robh+dt at kernel.org; mark.rutland at arm.com; catalin.marinas at arm.com;
> will.deacon at arm.com; devicetree at vger.kernel.org; linux-arm-
> kernel at lists.infradead.org; Andy Tang
> Subject: [PATCH] arm64: dts: updated sata node on ls1012a dts
>
> On ls1012a soc, sata ecc should be disabled. So added sata ecc register
> address so that driver can get this information.
>
> Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 80
> +++++++++++++++++++++++++-
> 1 file changed, 79 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> index cffebb4..1870dde 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> @@ -43,6 +43,7 @@
> */
>
> #include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/thermal/thermal.h>
>
> / {
> compatible = "fsl,ls1012a";
> @@ -126,6 +127,81 @@
> #clock-cells = <2>;
> clocks = <&sysclk>;
> };
> + tmu: tmu at 1f00000 {
> + compatible = "fsl,qoriq-tmu";
> + reg = <0x0 0x1f00000 0x0 0x10000>;
> + interrupts = <0 33 0x4>;
> + fsl,tmu-range = <0xb0000 0x9002a 0x6004c 0x30062>;
> + fsl,tmu-calibration = <0x00000000 0x00000026
> + 0x00000001 0x0000002d
> + 0x00000002 0x00000032
> + 0x00000003 0x00000039
> + 0x00000004 0x0000003f
> + 0x00000005 0x00000046
> + 0x00000006 0x0000004d
> + 0x00000007 0x00000054
> + 0x00000008 0x0000005a
> + 0x00000009 0x00000061
> + 0x0000000a 0x0000006a
> + 0x0000000b 0x00000071
> +
> + 0x00010000 0x00000025
> + 0x00010001 0x0000002c
> + 0x00010002 0x00000035
> + 0x00010003 0x0000003d
> + 0x00010004 0x00000045
> + 0x00010005 0x0000004e
> + 0x00010006 0x00000057
> + 0x00010007 0x00000061
> + 0x00010008 0x0000006b
> + 0x00010009 0x00000076
> +
> + 0x00020000 0x00000029
> + 0x00020001 0x00000033
> + 0x00020002 0x0000003d
> + 0x00020003 0x00000049
> + 0x00020004 0x00000056
> + 0x00020005 0x00000061
> + 0x00020006 0x0000006d
> +
> + 0x00030000 0x00000021
> + 0x00030001 0x0000002a
> + 0x00030002 0x0000003c
> + 0x00030003 0x0000004e>;
> + big-endian;
> + #thermal-sensor-cells = <1>;
> + };
> +
> + thermal-zones {
> + cpu_thermal: cpu-thermal {
> + polling-delay-passive = <1000>;
> + polling-delay = <5000>;
> +
> + thermal-sensors = <&tmu 0>;
> +
> + trips {
> + cpu_alert: cpu-alert {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + cpu_crit: cpu-crit {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu_alert>;
> + cooling-device =
> + <&cpu0
> THERMAL_NO_LIMIT
> +
> THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> + };
>
> i2c0: i2c at 2180000 {
> compatible = "fsl,vf610-i2c";
> @@ -238,7 +314,9 @@
>
> sata: sata at 3200000 {
> compatible = "fsl,ls1012a-ahci", "fsl,ls1043a-ahci";
> - reg = <0x0 0x3200000 0x0 0x10000>;
> + reg = <0x0 0x3200000 0x0 0x10000>,
> + <0x0 0x20140520 0x0 0x4>;
> + reg-names = "ahci", "sata-ecc";
> interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
> clocks = <&clockgen 4 0>;
> status = "disabled";
> --
> 2.1.0.27.g96db324
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2017-03-10 8:27 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-03-10 8:12 [PATCH] arm64: dts: updated sata node on ls1012a dts Yuantian Tang
2017-03-10 8:12 ` Yuantian Tang
[not found] ` <1489133533-39352-1-git-send-email-andy.tang-3arQi8VN3Tc@public.gmane.org>
2017-03-10 8:27 ` Andy Tang
2017-03-10 8:27 ` Andy Tang
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.