* [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15
@ 2017-03-20 7:52 Cédric Perles
2017-03-20 8:34 ` Mauro Salvini
0 siblings, 1 reply; 6+ messages in thread
From: Cédric Perles @ 2017-03-20 7:52 UTC (permalink / raw)
To: xenomai
Hi community,
I’m a Xenomai newby and I’m trying to install Xenomai 3.0.3 on my i.MX6
based board (kernel 4.1.15 from NXP).
So I followed the “Installing Xenomai 3.x” chapter in Xenomai.org site and
began to download ipipe-core-4.1.18-arm-8.patch.
Since my kernel is not 4.1.18 but 4.1.15, I had to slightly adapt the
patch to make it fit.
Then I ran prepare-kernel.sh that tells me everything was OK.
Finally I successfully compiled kernel (and saw a few ipipe and xenomai
source files were built with into kernel).
However, when I boot on that newly built kernel there is absolutely no
xenomai nor ipipe logs into kernel boot logs, and no /proc/xenomai at all.
I must have missed something or doing something wrong, but I don’t see.
==> Did somebody successfully run Xeno 3.0.3 on i.MX6 ?
==> What am I doing wrong ?
Regards,
Cédric
Sepro
Cédric PERLES
Software R&D engineer
SEPRO Robotique - Rue Henry Bessemer - Zone Acti-Est - CS 10084 - 85003 La
Roche sur Yon Cedex (France)
Tel : +33 (0)2 51 45 05 31
_____
<http://www.sepro-group.com/fr> www.sepro-group.com |
<https://twitter.com/seprogroup> twitter@SeproGroup
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 22984 bytes
Desc: not available
URL: <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/attachment.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image003.png
Type: image/png
Size: 818 bytes
Desc: not available
URL: <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/attachment.png>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15
2017-03-20 7:52 [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15 Cédric Perles
@ 2017-03-20 8:34 ` Mauro Salvini
2017-03-20 14:29 ` Cédric Perles
0 siblings, 1 reply; 6+ messages in thread
From: Mauro Salvini @ 2017-03-20 8:34 UTC (permalink / raw)
To: Cédric Perles; +Cc: xenomai
On Mon, 2017-03-20 at 08:52 +0100, Cédric Perles wrote:
> Hi community,
>
>
>
> I’m a Xenomai newby and I’m trying to install Xenomai 3.0.3 on my i.MX6
> based board (kernel 4.1.15 from NXP).
>
>
>
> So I followed the “Installing Xenomai 3.x” chapter in Xenomai.org site and
> began to download ipipe-core-4.1.18-arm-8.patch.
>
> Since my kernel is not 4.1.18 but 4.1.15, I had to slightly adapt the
> patch to make it fit.
>
> Then I ran prepare-kernel.sh that tells me everything was OK.
>
> Finally I successfully compiled kernel (and saw a few ipipe and xenomai
> source files were built with into kernel).
>
>
>
> However, when I boot on that newly built kernel there is absolutely no
> xenomai nor ipipe logs into kernel boot logs, and no /proc/xenomai at all.
>
> I must have missed something or doing something wrong, but I don’t see.
>
>
>
> ==> Did somebody successfully run Xeno 3.0.3 on i.MX6 ?
>
> ==> What am I doing wrong ?
>
Hi Cédric,
I'm using Xenomai 3.0.3 with 4.1.15 kernel from NXP community with
success.
What defconfig have you used to configure your kernel? Before build it,
did you check with 'make menuconfig' that i-pipe was enabled?
Regards
Mauro
>
>
> Regards,
>
>
>
> Cédric
>
>
>
>
> Sepro
>
> Cédric PERLES
> Software R&D engineer
> SEPRO Robotique - Rue Henry Bessemer - Zone Acti-Est - CS 10084 - 85003 La
> Roche sur Yon Cedex (France)
>
> Tel : +33 (0)2 51 45 05 31
>
> _____
>
> <http://www.sepro-group.com/fr> www.sepro-group.com |
> <https://twitter.com/seprogroup> twitter@SeproGroup
>
>
>
>
> -------------- next part --------------
> A non-text attachment was scrubbed...
> Name: image001.jpg
> Type: image/jpeg
> Size: 22984 bytes
> Desc: not available
> URL: <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/attachment.jpg>
> -------------- next part --------------
> A non-text attachment was scrubbed...
> Name: image003.png
> Type: image/png
> Size: 818 bytes
> Desc: not available
> URL: <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/attachment.png>
> _______________________________________________
> Xenomai mailing list
> Xenomai@xenomai.org
> https://xenomai.org/mailman/listinfo/xenomai
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15
2017-03-20 8:34 ` Mauro Salvini
@ 2017-03-20 14:29 ` Cédric Perles
2017-03-20 14:43 ` Mauro Salvini
0 siblings, 1 reply; 6+ messages in thread
From: Cédric Perles @ 2017-03-20 14:29 UTC (permalink / raw)
To: Mauro Salvini; +Cc: xenomai
Hi Mauro,
First of all, thx for your answer. Knowing that Xenomai 3.0.3 is possible on
iMX6 kernel 4.1.15 is already a relief for me.
I compile my kernel through BuildRoot that automatically builds the .config
file.
However, when I check into kernel menuconfig, I can see I-PIPE is selected
(kernel Features -> -*- Interrupt pipeline) and Xenomai is selected ([*]
Xenomai/cobalt ).
My .config file is also OK (CONFIG_IPIPE=y , CONFIG_IPIPE_CORE=y,
CONFIG_XENOMAI=y).
==> What IPIPE patch did you use ?
==> Does IPIPE need something from RootFS ?
Regards,
Cédric
Sepro<http://extranet.sepro-robotique.com/signatures/Logo_GROUP.jpg>
Cédric PERLES
Software R&D engineer
SEPRO Robotique - Rue Henry Bessemer - Zone Acti-Est - CS 10084 - 85003 La
Roche sur Yon Cedex (France)
Tel : +33 (0)2 51 45 05 31
________________________________
www.sepro-group.com <http://www.sepro-group.com/fr> | twitter@SeproGroup
<https://twitter.com/seprogroup>
-----Message d'origine-----
De : Mauro Salvini [mailto:mauro.salvini@smigroup.net]
Envoyé : lundi 20 mars 2017 09:34
À : Cédric Perles
Cc : xenomai@xenomai.org
Objet : Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15
On Mon, 2017-03-20 at 08:52 +0100, Cédric Perles wrote:
> Hi community,
>
>
>
> I’m a Xenomai newby and I’m trying to install Xenomai 3.0.3 on my
> i.MX6 based board (kernel 4.1.15 from NXP).
>
>
>
> So I followed the “Installing Xenomai 3.x” chapter in Xenomai.org site
> and began to download ipipe-core-4.1.18-arm-8.patch.
>
> Since my kernel is not 4.1.18 but 4.1.15, I had to slightly adapt the
> patch to make it fit.
>
> Then I ran prepare-kernel.sh that tells me everything was OK.
>
> Finally I successfully compiled kernel (and saw a few ipipe and
> xenomai source files were built with into kernel).
>
>
>
> However, when I boot on that newly built kernel there is absolutely no
> xenomai nor ipipe logs into kernel boot logs, and no /proc/xenomai at all.
>
> I must have missed something or doing something wrong, but I don’t see.
>
>
>
> ==> Did somebody successfully run Xeno 3.0.3 on i.MX6 ?
>
> ==> What am I doing wrong ?
>
Hi Cédric,
I'm using Xenomai 3.0.3 with 4.1.15 kernel from NXP community with success.
What defconfig have you used to configure your kernel? Before build it, did
you check with 'make menuconfig' that i-pipe was enabled?
Regards
Mauro
>
>
> Regards,
>
>
>
> Cédric
>
>
>
>
> Sepro
>
> Cédric PERLES
> Software R&D engineer
> SEPRO Robotique - Rue Henry Bessemer - Zone Acti-Est - CS 10084 -
> 85003 La Roche sur Yon Cedex (France)
>
> Tel : +33 (0)2 51 45 05 31
>
> _____
>
> <http://www.sepro-group.com/fr> www.sepro-group.com |
> <https://twitter.com/seprogroup> twitter@SeproGroup
>
>
>
>
> -------------- next part -------------- A non-text attachment was
> scrubbed...
> Name: image001.jpg
> Type: image/jpeg
> Size: 22984 bytes
> Desc: not available
> URL:
> <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/at
> tachment.jpg>
> -------------- next part -------------- A non-text attachment was
> scrubbed...
> Name: image003.png
> Type: image/png
> Size: 818 bytes
> Desc: not available
> URL:
> <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/at
> tachment.png> _______________________________________________
> Xenomai mailing list
> Xenomai@xenomai.org
> https://xenomai.org/mailman/listinfo/xenomai
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15
2017-03-20 14:29 ` Cédric Perles
@ 2017-03-20 14:43 ` Mauro Salvini
2017-03-20 16:34 ` Cédric Perles
0 siblings, 1 reply; 6+ messages in thread
From: Mauro Salvini @ 2017-03-20 14:43 UTC (permalink / raw)
To: Cédric Perles; +Cc: xenomai
On Mon, 2017-03-20 at 15:29 +0100, Cédric Perles wrote:
> Hi Mauro,
>
> First of all, thx for your answer. Knowing that Xenomai 3.0.3 is possible on
> iMX6 kernel 4.1.15 is already a relief for me.
>
> I compile my kernel through BuildRoot that automatically builds the .config
> file.
> However, when I check into kernel menuconfig, I can see I-PIPE is selected
> (kernel Features -> -*- Interrupt pipeline) and Xenomai is selected ([*]
> Xenomai/cobalt ).
> My .config file is also OK (CONFIG_IPIPE=y , CONFIG_IPIPE_CORE=y,
> CONFIG_XENOMAI=y).
>
> ==> What IPIPE patch did you use ?
I use ipipe-core-4.1.18-arm-9 from git.xenomai.org without problem.
Configuration comes from Yocto's meta-freescale layer defconfig.
> ==> Does IPIPE need something from RootFS ?
AFAIK no, you don't need anything from rootfs to enable i-pipe in
kernel.
So running from console
dmesg | grep -i -e pipe -e xenomai
doesn't show nothing?
Regards
Mauro
>
> Regards,
>
> Cédric
>
> Sepro<http://extranet.sepro-robotique.com/signatures/Logo_GROUP.jpg>
>
> Cédric PERLES
> Software R&D engineer
> SEPRO Robotique - Rue Henry Bessemer - Zone Acti-Est - CS 10084 - 85003 La
> Roche sur Yon Cedex (France)
>
> Tel : +33 (0)2 51 45 05 31
>
> ________________________________
>
> www.sepro-group.com <http://www.sepro-group.com/fr> | twitter@SeproGroup
> <https://twitter.com/seprogroup>
>
>
>
>
> -----Message d'origine-----
> De : Mauro Salvini [mailto:mauro.salvini@smigroup.net]
> Envoyé : lundi 20 mars 2017 09:34
> À : Cédric Perles
> Cc : xenomai@xenomai.org
> Objet : Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15
>
> On Mon, 2017-03-20 at 08:52 +0100, Cédric Perles wrote:
> > Hi community,
> >
> >
> >
> > I’m a Xenomai newby and I’m trying to install Xenomai 3.0.3 on my
> > i.MX6 based board (kernel 4.1.15 from NXP).
> >
> >
> >
> > So I followed the “Installing Xenomai 3.x” chapter in Xenomai.org site
> > and began to download ipipe-core-4.1.18-arm-8.patch.
> >
> > Since my kernel is not 4.1.18 but 4.1.15, I had to slightly adapt the
> > patch to make it fit.
> >
> > Then I ran prepare-kernel.sh that tells me everything was OK.
> >
> > Finally I successfully compiled kernel (and saw a few ipipe and
> > xenomai source files were built with into kernel).
> >
> >
> >
> > However, when I boot on that newly built kernel there is absolutely no
> > xenomai nor ipipe logs into kernel boot logs, and no /proc/xenomai at all.
> >
> > I must have missed something or doing something wrong, but I don’t see.
> >
> >
> >
> > ==> Did somebody successfully run Xeno 3.0.3 on i.MX6 ?
> >
> > ==> What am I doing wrong ?
> >
> Hi Cédric,
>
> I'm using Xenomai 3.0.3 with 4.1.15 kernel from NXP community with success.
>
> What defconfig have you used to configure your kernel? Before build it, did
> you check with 'make menuconfig' that i-pipe was enabled?
>
> Regards
> Mauro
> >
> >
> > Regards,
> >
> >
> >
> > Cédric
> >
> >
> >
> >
> > Sepro
> >
> > Cédric PERLES
> > Software R&D engineer
> > SEPRO Robotique - Rue Henry Bessemer - Zone Acti-Est - CS 10084 -
> > 85003 La Roche sur Yon Cedex (France)
> >
> > Tel : +33 (0)2 51 45 05 31
> >
> > _____
> >
> > <http://www.sepro-group.com/fr> www.sepro-group.com |
> > <https://twitter.com/seprogroup> twitter@SeproGroup
> >
> >
> >
> >
> > -------------- next part -------------- A non-text attachment was
> > scrubbed...
> > Name: image001.jpg
> > Type: image/jpeg
> > Size: 22984 bytes
> > Desc: not available
> > URL:
> > <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/at
> > tachment.jpg>
> > -------------- next part -------------- A non-text attachment was
> > scrubbed...
> > Name: image003.png
> > Type: image/png
> > Size: 818 bytes
> > Desc: not available
> > URL:
> > <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/at
> > tachment.png> _______________________________________________
> > Xenomai mailing list
> > Xenomai@xenomai.org
> > https://xenomai.org/mailman/listinfo/xenomai
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15
2017-03-20 14:43 ` Mauro Salvini
@ 2017-03-20 16:34 ` Cédric Perles
2017-03-21 7:38 ` Mauro Salvini
0 siblings, 1 reply; 6+ messages in thread
From: Cédric Perles @ 2017-03-20 16:34 UTC (permalink / raw)
To: Mauro Salvini; +Cc: xenomai
Hi Mauro,
In fact, I was booting the wrong kernel through tftp. Using the correct one,
I have indeed IPIPE and XENOMAI running.
Sorry for bothering you and thx for your time.
By the way, is there any classical traps to know concerning Xeno 3.0.3 on
iMX6 ?
Regards
Cédric
-----Message d'origine-----
De : Mauro Salvini [mailto:mauro.salvini@smigroup.net]
Envoyé : lundi 20 mars 2017 15:44
À : Cédric Perles
Cc : xenomai@xenomai.org
Objet : Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15
On Mon, 2017-03-20 at 15:29 +0100, Cédric Perles wrote:
> Hi Mauro,
>
> First of all, thx for your answer. Knowing that Xenomai 3.0.3 is
> possible on
> iMX6 kernel 4.1.15 is already a relief for me.
>
> I compile my kernel through BuildRoot that automatically builds the
> .config file.
> However, when I check into kernel menuconfig, I can see I-PIPE is
> selected (kernel Features -> -*- Interrupt pipeline) and Xenomai is
> selected ([*] Xenomai/cobalt ).
> My .config file is also OK (CONFIG_IPIPE=y , CONFIG_IPIPE_CORE=y,
> CONFIG_XENOMAI=y).
>
> ==> What IPIPE patch did you use ?
I use ipipe-core-4.1.18-arm-9 from git.xenomai.org without problem.
Configuration comes from Yocto's meta-freescale layer defconfig.
> ==> Does IPIPE need something from RootFS ?
AFAIK no, you don't need anything from rootfs to enable i-pipe in kernel.
So running from console
dmesg | grep -i -e pipe -e xenomai
doesn't show nothing?
Regards
Mauro
>
> Regards,
>
> Cédric
>
> Sepro<http://extranet.sepro-robotique.com/signatures/Logo_GROUP.jpg>
>
> Cédric PERLES
> Software R&D engineer
> SEPRO Robotique - Rue Henry Bessemer - Zone Acti-Est - CS 10084 -
> 85003 La Roche sur Yon Cedex (France)
>
> Tel : +33 (0)2 51 45 05 31
>
> ________________________________
>
> www.sepro-group.com <http://www.sepro-group.com/fr> |
> twitter@SeproGroup <https://twitter.com/seprogroup>
>
>
>
>
> -----Message d'origine-----
> De : Mauro Salvini [mailto:mauro.salvini@smigroup.net]
> Envoyé : lundi 20 mars 2017 09:34
> À : Cédric Perles
> Cc : xenomai@xenomai.org
> Objet : Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel
> 4.1.15
>
> On Mon, 2017-03-20 at 08:52 +0100, Cédric Perles wrote:
> > Hi community,
> >
> >
> >
> > I’m a Xenomai newby and I’m trying to install Xenomai 3.0.3 on my
> > i.MX6 based board (kernel 4.1.15 from NXP).
> >
> >
> >
> > So I followed the “Installing Xenomai 3.x” chapter in Xenomai.org
> > site and began to download ipipe-core-4.1.18-arm-8.patch.
> >
> > Since my kernel is not 4.1.18 but 4.1.15, I had to slightly adapt
> > the patch to make it fit.
> >
> > Then I ran prepare-kernel.sh that tells me everything was OK.
> >
> > Finally I successfully compiled kernel (and saw a few ipipe and
> > xenomai source files were built with into kernel).
> >
> >
> >
> > However, when I boot on that newly built kernel there is absolutely
> > no xenomai nor ipipe logs into kernel boot logs, and no /proc/xenomai at
> > all.
> >
> > I must have missed something or doing something wrong, but I don’t see.
> >
> >
> >
> > ==> Did somebody successfully run Xeno 3.0.3 on i.MX6 ?
> >
> > ==> What am I doing wrong ?
> >
> Hi Cédric,
>
> I'm using Xenomai 3.0.3 with 4.1.15 kernel from NXP community with
> success.
>
> What defconfig have you used to configure your kernel? Before build
> it, did you check with 'make menuconfig' that i-pipe was enabled?
>
> Regards
> Mauro
> >
> >
> > Regards,
> >
> >
> >
> > Cédric
> >
> >
> >
> >
> > Sepro
> >
> > Cédric PERLES
> > Software R&D engineer
> > SEPRO Robotique - Rue Henry Bessemer - Zone Acti-Est - CS 10084 -
> > 85003 La Roche sur Yon Cedex (France)
> >
> > Tel : +33 (0)2 51 45 05 31
> >
> > _____
> >
> > <http://www.sepro-group.com/fr> www.sepro-group.com |
> > <https://twitter.com/seprogroup> twitter@SeproGroup
> >
> >
> >
> >
> > -------------- next part -------------- A non-text attachment was
> > scrubbed...
> > Name: image001.jpg
> > Type: image/jpeg
> > Size: 22984 bytes
> > Desc: not available
> > URL:
> > <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/
> > at
> > tachment.jpg>
> > -------------- next part -------------- A non-text attachment was
> > scrubbed...
> > Name: image003.png
> > Type: image/png
> > Size: 818 bytes
> > Desc: not available
> > URL:
> > <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/
> > at tachment.png> _______________________________________________
> > Xenomai mailing list
> > Xenomai@xenomai.org
> > https://xenomai.org/mailman/listinfo/xenomai
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15
2017-03-20 16:34 ` Cédric Perles
@ 2017-03-21 7:38 ` Mauro Salvini
0 siblings, 0 replies; 6+ messages in thread
From: Mauro Salvini @ 2017-03-21 7:38 UTC (permalink / raw)
To: Cédric Perles; +Cc: xenomai
On Mon, 2017-03-20 at 17:34 +0100, Cédric Perles wrote:
> Hi Mauro,
>
> In fact, I was booting the wrong kernel through tftp. Using the correct one,
> I have indeed IPIPE and XENOMAI running.
> Sorry for bothering you and thx for your time.
You are welcome.
>
> By the way, is there any classical traps to know concerning Xeno 3.0.3 on
> iMX6 ?
You should pay attention to L2 cache: if you experience high latencies
it could be a culprit (see cache write disable handling in
arch/arm/mm/cache-l2x0.c). For everything else, I have found all things
I needed in documentation and mailing-list.
Regards
>
> Regards
>
> Cédric
>
>
>
>
> -----Message d'origine-----
> De : Mauro Salvini [mailto:mauro.salvini@smigroup.net]
> Envoyé : lundi 20 mars 2017 15:44
> À : Cédric Perles
> Cc : xenomai@xenomai.org
> Objet : Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15
>
> On Mon, 2017-03-20 at 15:29 +0100, Cédric Perles wrote:
> > Hi Mauro,
> >
> > First of all, thx for your answer. Knowing that Xenomai 3.0.3 is
> > possible on
> > iMX6 kernel 4.1.15 is already a relief for me.
> >
> > I compile my kernel through BuildRoot that automatically builds the
> > .config file.
> > However, when I check into kernel menuconfig, I can see I-PIPE is
> > selected (kernel Features -> -*- Interrupt pipeline) and Xenomai is
> > selected ([*] Xenomai/cobalt ).
> > My .config file is also OK (CONFIG_IPIPE=y , CONFIG_IPIPE_CORE=y,
> > CONFIG_XENOMAI=y).
> >
> > ==> What IPIPE patch did you use ?
> I use ipipe-core-4.1.18-arm-9 from git.xenomai.org without problem.
> Configuration comes from Yocto's meta-freescale layer defconfig.
>
> > ==> Does IPIPE need something from RootFS ?
> AFAIK no, you don't need anything from rootfs to enable i-pipe in kernel.
>
>
> So running from console
>
> dmesg | grep -i -e pipe -e xenomai
>
> doesn't show nothing?
>
> Regards
> Mauro
>
> >
> > Regards,
> >
> > Cédric
> >
> > Sepro<http://extranet.sepro-robotique.com/signatures/Logo_GROUP.jpg>
> >
> > Cédric PERLES
> > Software R&D engineer
> > SEPRO Robotique - Rue Henry Bessemer - Zone Acti-Est - CS 10084 -
> > 85003 La Roche sur Yon Cedex (France)
> >
> > Tel : +33 (0)2 51 45 05 31
> >
> > ________________________________
> >
> > www.sepro-group.com <http://www.sepro-group.com/fr> |
> > twitter@SeproGroup <https://twitter.com/seprogroup>
> >
> >
> >
> >
> > -----Message d'origine-----
> > De : Mauro Salvini [mailto:mauro.salvini@smigroup.net]
> > Envoyé : lundi 20 mars 2017 09:34
> > À : Cédric Perles
> > Cc : xenomai@xenomai.org
> > Objet : Re: [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel
> > 4.1.15
> >
> > On Mon, 2017-03-20 at 08:52 +0100, Cédric Perles wrote:
> > > Hi community,
> > >
> > >
> > >
> > > I’m a Xenomai newby and I’m trying to install Xenomai 3.0.3 on my
> > > i.MX6 based board (kernel 4.1.15 from NXP).
> > >
> > >
> > >
> > > So I followed the “Installing Xenomai 3.x” chapter in Xenomai.org
> > > site and began to download ipipe-core-4.1.18-arm-8.patch.
> > >
> > > Since my kernel is not 4.1.18 but 4.1.15, I had to slightly adapt
> > > the patch to make it fit.
> > >
> > > Then I ran prepare-kernel.sh that tells me everything was OK.
> > >
> > > Finally I successfully compiled kernel (and saw a few ipipe and
> > > xenomai source files were built with into kernel).
> > >
> > >
> > >
> > > However, when I boot on that newly built kernel there is absolutely
> > > no xenomai nor ipipe logs into kernel boot logs, and no /proc/xenomai at
> > > all.
> > >
> > > I must have missed something or doing something wrong, but I don’t see.
> > >
> > >
> > >
> > > ==> Did somebody successfully run Xeno 3.0.3 on i.MX6 ?
> > >
> > > ==> What am I doing wrong ?
> > >
> > Hi Cédric,
> >
> > I'm using Xenomai 3.0.3 with 4.1.15 kernel from NXP community with
> > success.
> >
> > What defconfig have you used to configure your kernel? Before build
> > it, did you check with 'make menuconfig' that i-pipe was enabled?
> >
> > Regards
> > Mauro
> > >
> > >
> > > Regards,
> > >
> > >
> > >
> > > Cédric
> > >
> > >
> > >
> > >
> > > Sepro
> > >
> > > Cédric PERLES
> > > Software R&D engineer
> > > SEPRO Robotique - Rue Henry Bessemer - Zone Acti-Est - CS 10084 -
> > > 85003 La Roche sur Yon Cedex (France)
> > >
> > > Tel : +33 (0)2 51 45 05 31
> > >
> > > _____
> > >
> > > <http://www.sepro-group.com/fr> www.sepro-group.com |
> > > <https://twitter.com/seprogroup> twitter@SeproGroup
> > >
> > >
> > >
> > >
> > > -------------- next part -------------- A non-text attachment was
> > > scrubbed...
> > > Name: image001.jpg
> > > Type: image/jpeg
> > > Size: 22984 bytes
> > > Desc: not available
> > > URL:
> > > <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/
> > > at
> > > tachment.jpg>
> > > -------------- next part -------------- A non-text attachment was
> > > scrubbed...
> > > Name: image003.png
> > > Type: image/png
> > > Size: 818 bytes
> > > Desc: not available
> > > URL:
> > > <http://xenomai.org/pipermail/xenomai/attachments/20170320/50daa0cf/
> > > at tachment.png> _______________________________________________
> > > Xenomai mailing list
> > > Xenomai@xenomai.org
> > > https://xenomai.org/mailman/listinfo/xenomai
> >
>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2017-03-21 7:38 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-03-20 7:52 [Xenomai] Trying to install Xenomai 3.0.3 on i.MX6 Kernel 4.1.15 Cédric Perles
2017-03-20 8:34 ` Mauro Salvini
2017-03-20 14:29 ` Cédric Perles
2017-03-20 14:43 ` Mauro Salvini
2017-03-20 16:34 ` Cédric Perles
2017-03-21 7:38 ` Mauro Salvini
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.