* [PATCH v5 1/2] dt-bindings: i2c: mux: ltc4306: Add dt-bindings for I2C multiplexer/switch @ 2017-04-11 12:16 ` michael.hennerich 0 siblings, 0 replies; 7+ messages in thread From: michael.hennerich @ 2017-04-11 12:16 UTC (permalink / raw) To: wsa, peda, robh+dt, mark.rutland, linus.walleij Cc: linux-i2c, devicetree, linux-gpio, linux-kernel, Michael Hennerich From: Michael Hennerich <michael.hennerich@analog.com> This patch adds support for the Analog Devices / Linear Technology LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches. The LTC4306 optionally provides two general purpose input/output pins (GPIOs) that can be configured as logic inputs, opendrain outputs or push-pull outputs via the generic GPIOLIB framework. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Acked-by: Rob Herring <robh@kernel.org> --- .../devicetree/bindings/i2c/i2c-mux-ltc4306.txt | 61 ++++++++++++++++++++++ 1 file changed, 61 insertions(+) create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt new file mode 100644 index 0000000..1e98c6b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt @@ -0,0 +1,61 @@ +* Linear Technology / Analog Devices I2C bus switch + +Required Properties: + + - compatible: Must contain one of the following. + "lltc,ltc4305", "lltc,ltc4306" + - reg: The I2C address of the device. + + The following required properties are defined externally: + + - Standard I2C mux properties. See i2c-mux.txt in this directory. + - I2C child bus nodes. See i2c-mux.txt in this directory. + +Optional Properties: + + - enable-gpios: Reference to the GPIO connected to the enable input. + - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all + children in idle state. This is necessary for example, if there are several + multiplexers on the bus and the devices behind them use same I2C addresses. + - gpio-controller: Marks the device node as a GPIO Controller. + - #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - ltc,downstream-accelerators-enable: Enables the rise time accelerators + on the downstream port. + - ltc,upstream-accelerators-enable: Enables the rise time accelerators + on the upstream port. + +Example: + + ltc4306: i2c-mux@4a { + compatible = "lltc,ltc4306"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4a>; + + gpio-controller; + #gpio-cells = <2>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + eeprom@50 { + compatible = "at,24c02"; + reg = <0x50>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + eeprom@50 { + compatible = "at,24c02"; + reg = <0x50>; + }; + }; + }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v5 1/2] dt-bindings: i2c: mux: ltc4306: Add dt-bindings for I2C multiplexer/switch @ 2017-04-11 12:16 ` michael.hennerich 0 siblings, 0 replies; 7+ messages in thread From: michael.hennerich @ 2017-04-11 12:16 UTC (permalink / raw) To: wsa, peda, robh+dt, mark.rutland, linus.walleij Cc: linux-i2c, devicetree, linux-gpio, linux-kernel, Michael Hennerich From: Michael Hennerich <michael.hennerich@analog.com> This patch adds support for the Analog Devices / Linear Technology LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches. The LTC4306 optionally provides two general purpose input/output pins (GPIOs) that can be configured as logic inputs, opendrain outputs or push-pull outputs via the generic GPIOLIB framework. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Acked-by: Rob Herring <robh@kernel.org> --- .../devicetree/bindings/i2c/i2c-mux-ltc4306.txt | 61 ++++++++++++++++++++++ 1 file changed, 61 insertions(+) create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt new file mode 100644 index 0000000..1e98c6b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt @@ -0,0 +1,61 @@ +* Linear Technology / Analog Devices I2C bus switch + +Required Properties: + + - compatible: Must contain one of the following. + "lltc,ltc4305", "lltc,ltc4306" + - reg: The I2C address of the device. + + The following required properties are defined externally: + + - Standard I2C mux properties. See i2c-mux.txt in this directory. + - I2C child bus nodes. See i2c-mux.txt in this directory. + +Optional Properties: + + - enable-gpios: Reference to the GPIO connected to the enable input. + - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all + children in idle state. This is necessary for example, if there are several + multiplexers on the bus and the devices behind them use same I2C addresses. + - gpio-controller: Marks the device node as a GPIO Controller. + - #gpio-cells: Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - ltc,downstream-accelerators-enable: Enables the rise time accelerators + on the downstream port. + - ltc,upstream-accelerators-enable: Enables the rise time accelerators + on the upstream port. + +Example: + + ltc4306: i2c-mux@4a { + compatible = "lltc,ltc4306"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4a>; + + gpio-controller; + #gpio-cells = <2>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + eeprom@50 { + compatible = "at,24c02"; + reg = <0x50>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + eeprom@50 { + compatible = "at,24c02"; + reg = <0x50>; + }; + }; + }; -- 2.7.4 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v5 2/2] i2c: mux: ltc4306: LTC4306 and LTC4305 I2C multiplexer/switch 2017-04-11 12:16 ` michael.hennerich @ 2017-04-11 12:16 ` michael.hennerich -1 siblings, 0 replies; 7+ messages in thread From: michael.hennerich @ 2017-04-11 12:16 UTC (permalink / raw) To: wsa, peda, robh+dt, mark.rutland, linus.walleij Cc: linux-i2c, devicetree, linux-gpio, linux-kernel, Michael Hennerich From: Michael Hennerich <michael.hennerich@analog.com> This patch adds support for the Analog Devices / Linear Technology LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches. The LTC4306 optionally provides two general purpose input/output pins (GPIOs) that can be configured as logic inputs, opendrain outputs or push-pull outputs via the generic GPIOLIB framework. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> --- Changes since v1: - Sort makefile entries - Sort driver includes - Use proper defines - Miscellaneous coding style fixups - Rename mux select callback - Revise i2c-mux-idle-disconnect handling - Add ENABLE GPIO handling on error and device removal. - Remove surplus of_match_device call. Changes since v2: - Stop double error reporting (i2c_mux_add_adapter) - Change subject - Split dt bindings to separate patch Changes since v3: - Change subject and add spaces - Convert to I2C_MUX_LOCKED - Convert to regmap - Remove local register cache - Restore previous ENABLE GPIO handling - Initially pulse ENABLE low - Eliminate i2c client struct in driver state structure - Simplify error return path - Misc minor cleanups Changes since v4: - Remove redundant includes - Use regmap cache type REGCACHE_FLAT - gpio_get restore double negates on return - Implement gpio_get_direction - Use unified device property interface - mux_alloc exact number of channels - Reword kconfig help text --- MAINTAINERS | 8 + drivers/i2c/muxes/Kconfig | 11 ++ drivers/i2c/muxes/Makefile | 1 + drivers/i2c/muxes/i2c-mux-ltc4306.c | 322 ++++++++++++++++++++++++++++++++++++ 4 files changed, 342 insertions(+) create mode 100644 drivers/i2c/muxes/i2c-mux-ltc4306.c diff --git a/MAINTAINERS b/MAINTAINERS index c776906..9a27a19 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -7698,6 +7698,14 @@ S: Maintained F: Documentation/hwmon/ltc4261 F: drivers/hwmon/ltc4261.c +LTC4306 I2C MULTIPLEXER DRIVER +M: Michael Hennerich <michael.hennerich@analog.com> +W: http://ez.analog.com/community/linux-device-drivers +L: linux-i2c@vger.kernel.org +S: Supported +F: drivers/i2c/muxes/i2c-mux-ltc4306.c +F: Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt + LTP (Linux Test Project) M: Mike Frysinger <vapier@gentoo.org> M: Cyril Hrubis <chrubis@suse.cz> diff --git a/drivers/i2c/muxes/Kconfig b/drivers/i2c/muxes/Kconfig index 10b3d17..1e160fc 100644 --- a/drivers/i2c/muxes/Kconfig +++ b/drivers/i2c/muxes/Kconfig @@ -30,6 +30,17 @@ config I2C_MUX_GPIO This driver can also be built as a module. If so, the module will be called i2c-mux-gpio. +config I2C_MUX_LTC4306 + tristate "LTC LTC4306/5 I2C multiplexer" + select GPIOLIB + select REGMAP_I2C + help + If you say yes here you get support for the Analog Devices + LTC4306 or LTC4305 I2C mux/switch devices. + + This driver can also be built as a module. If so, the module + will be called i2c-mux-ltc4306. + config I2C_MUX_PCA9541 tristate "NXP PCA9541 I2C Master Selector" help diff --git a/drivers/i2c/muxes/Makefile b/drivers/i2c/muxes/Makefile index 9948fa4..ff7618c 100644 --- a/drivers/i2c/muxes/Makefile +++ b/drivers/i2c/muxes/Makefile @@ -6,6 +6,7 @@ obj-$(CONFIG_I2C_ARB_GPIO_CHALLENGE) += i2c-arb-gpio-challenge.o obj-$(CONFIG_I2C_DEMUX_PINCTRL) += i2c-demux-pinctrl.o obj-$(CONFIG_I2C_MUX_GPIO) += i2c-mux-gpio.o +obj-$(CONFIG_I2C_MUX_LTC4306) += i2c-mux-ltc4306.o obj-$(CONFIG_I2C_MUX_MLXCPLD) += i2c-mux-mlxcpld.o obj-$(CONFIG_I2C_MUX_PCA9541) += i2c-mux-pca9541.o obj-$(CONFIG_I2C_MUX_PCA954x) += i2c-mux-pca954x.o diff --git a/drivers/i2c/muxes/i2c-mux-ltc4306.c b/drivers/i2c/muxes/i2c-mux-ltc4306.c new file mode 100644 index 0000000..311b1cc --- /dev/null +++ b/drivers/i2c/muxes/i2c-mux-ltc4306.c @@ -0,0 +1,322 @@ +/* + * Linear Technology LTC4306 and LTC4305 I2C multiplexer/switch + * + * Copyright (C) 2017 Analog Devices Inc. + * + * Licensed under the GPL-2. + * + * Based on: i2c-mux-pca954x.c + * + * Datasheet: http://cds.linear.com/docs/en/datasheet/4306.pdf + */ + +#include <linux/gpio/consumer.h> +#include <linux/gpio/driver.h> +#include <linux/i2c-mux.h> +#include <linux/i2c.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/property.h> +#include <linux/regmap.h> +#include <linux/slab.h> + +#define LTC4305_MAX_NCHANS 2 +#define LTC4306_MAX_NCHANS 4 + +#define LTC_REG_STATUS 0x0 +#define LTC_REG_CONFIG 0x1 +#define LTC_REG_MODE 0x2 +#define LTC_REG_SWITCH 0x3 + +#define LTC_DOWNSTREAM_ACCL_EN BIT(6) +#define LTC_UPSTREAM_ACCL_EN BIT(7) + +#define LTC_GPIO_ALL_INPUT 0xC0 +#define LTC_SWITCH_MASK 0xF0 + +enum ltc_type { + ltc_4305, + ltc_4306, +}; + +struct chip_desc { + u8 nchans; + u8 num_gpios; +}; + +struct ltc4306 { + struct regmap *regmap; + struct gpio_chip gpiochip; + const struct chip_desc *chip; +}; + +static const struct chip_desc chips[] = { + [ltc_4305] = { + .nchans = LTC4305_MAX_NCHANS, + }, + [ltc_4306] = { + .nchans = LTC4306_MAX_NCHANS, + .num_gpios = 2, + }, +}; + +static bool ltc4306_is_volatile_reg(struct device *dev, unsigned int reg) +{ + return (reg == LTC_REG_CONFIG) ? true : false; +} + +static const struct regmap_config ltc4306_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = LTC_REG_SWITCH, + .volatile_reg = ltc4306_is_volatile_reg, + .cache_type = REGCACHE_FLAT, +}; + +static int ltc4306_gpio_get(struct gpio_chip *chip, unsigned int offset) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + unsigned int val; + int ret; + + ret = regmap_read(data->regmap, LTC_REG_CONFIG, &val); + if (ret < 0) + return ret; + + return !!(val & BIT(1 - offset)); +} + +static void ltc4306_gpio_set(struct gpio_chip *chip, unsigned int offset, + int value) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + + regmap_update_bits(data->regmap, LTC_REG_CONFIG, BIT(5 - offset), + value ? BIT(5 - offset) : 0); +} + +static int ltc4306_gpio_get_direction(struct gpio_chip *chip, + unsigned int offset) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + unsigned int val; + int ret; + + ret = regmap_read(data->regmap, LTC_REG_MODE, &val); + if (ret < 0) + return ret; + + return !!(val & BIT(7 - offset)); +} + +static int ltc4306_gpio_direction_input(struct gpio_chip *chip, + unsigned int offset) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + + return regmap_update_bits(data->regmap, LTC_REG_MODE, + BIT(7 - offset), BIT(7 - offset)); +} + +static int ltc4306_gpio_direction_output(struct gpio_chip *chip, + unsigned int offset, int value) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + + ltc4306_gpio_set(chip, offset, value); + return regmap_update_bits(data->regmap, LTC_REG_MODE, + BIT(7 - offset), 0); +} + +static int ltc4306_gpio_set_config(struct gpio_chip *chip, + unsigned int offset, unsigned long config) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + unsigned int val; + + switch (pinconf_to_config_param(config)) { + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + val = 0; + break; + case PIN_CONFIG_DRIVE_PUSH_PULL: + val = BIT(4 - offset); + break; + default: + return -ENOTSUPP; + } + + return regmap_update_bits(data->regmap, LTC_REG_MODE, + BIT(4 - offset), val); +} + +static int ltc4306_gpio_init(struct ltc4306 *data) +{ + struct device *dev = regmap_get_device(data->regmap); + + if (!data->chip->num_gpios) + return 0; + + data->gpiochip.label = dev_name(dev); + data->gpiochip.base = -1; + data->gpiochip.ngpio = data->chip->num_gpios; + data->gpiochip.parent = dev; + data->gpiochip.can_sleep = true; + data->gpiochip.get_direction = ltc4306_gpio_get_direction; + data->gpiochip.direction_input = ltc4306_gpio_direction_input; + data->gpiochip.direction_output = ltc4306_gpio_direction_output; + data->gpiochip.get = ltc4306_gpio_get; + data->gpiochip.set = ltc4306_gpio_set; + data->gpiochip.set_config = ltc4306_gpio_set_config; + data->gpiochip.owner = THIS_MODULE; + + /* gpiolib assumes all GPIOs default input */ + regmap_write(data->regmap, LTC_REG_MODE, LTC_GPIO_ALL_INPUT); + + return devm_gpiochip_add_data(dev, &data->gpiochip, data); +} + +static int ltc4306_select_mux(struct i2c_mux_core *muxc, u32 chan) +{ + struct ltc4306 *data = i2c_mux_priv(muxc); + + return regmap_update_bits(data->regmap, LTC_REG_SWITCH, + LTC_SWITCH_MASK, BIT(7 - chan)); +} + +static int ltc4306_deselect_mux(struct i2c_mux_core *muxc, u32 chan) +{ + struct ltc4306 *data = i2c_mux_priv(muxc); + + return regmap_update_bits(data->regmap, LTC_REG_SWITCH, + LTC_SWITCH_MASK, 0); +} + +static const struct i2c_device_id ltc4306_id[] = { + { "ltc4305", ltc_4305 }, + { "ltc4306", ltc_4306 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ltc4306_id); + +static const struct of_device_id ltc4306_of_match[] = { + { .compatible = "lltc,ltc4305", .data = &chips[ltc_4305] }, + { .compatible = "lltc,ltc4306", .data = &chips[ltc_4306] }, + { } +}; +MODULE_DEVICE_TABLE(of, ltc4306_of_match); + +static int ltc4306_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct i2c_adapter *adap = to_i2c_adapter(client->dev.parent); + const struct chip_desc *chip; + struct i2c_mux_core *muxc; + struct ltc4306 *data; + struct gpio_desc *gpio; + bool idle_disc; + unsigned int val = 0; + int num, ret; + + chip = of_device_get_match_data(&client->dev); + + if (!chip) + chip = &chips[id->driver_data]; + + idle_disc = device_property_read_bool(&client->dev, + "i2c-mux-idle-disconnect"); + + muxc = i2c_mux_alloc(adap, &client->dev, + chip->nchans, sizeof(*data), + I2C_MUX_LOCKED, ltc4306_select_mux, + idle_disc ? ltc4306_deselect_mux : NULL); + if (!muxc) + return -ENOMEM; + data = i2c_mux_priv(muxc); + data->chip = chip; + + i2c_set_clientdata(client, muxc); + + data->regmap = devm_regmap_init_i2c(client, <c4306_regmap_config); + if (IS_ERR(data->regmap)) { + ret = PTR_ERR(data->regmap); + dev_err(&client->dev, "Failed to allocate register map: %d\n", + ret); + return ret; + } + + /* Reset and enable the mux if an enable GPIO is specified. */ + gpio = devm_gpiod_get_optional(&client->dev, "enable", GPIOD_OUT_LOW); + if (IS_ERR(gpio)) + return PTR_ERR(gpio); + + if (gpio) { + udelay(1); + gpiod_set_value(gpio, 1); + } + + /* + * Write the mux register at addr to verify + * that the mux is in fact present. This also + * initializes the mux to disconnected state. + */ + if (regmap_write(data->regmap, LTC_REG_SWITCH, 0) < 0) { + dev_warn(&client->dev, "probe failed\n"); + return -ENODEV; + } + + if (device_property_read_bool(&client->dev, + "ltc,downstream-accelerators-enable")) + val |= LTC_DOWNSTREAM_ACCL_EN; + + if (device_property_read_bool(&client->dev, + "ltc,upstream-accelerators-enable")) + val |= LTC_UPSTREAM_ACCL_EN; + + if (regmap_write(data->regmap, LTC_REG_CONFIG, val) < 0) + return -ENODEV; + + ret = ltc4306_gpio_init(data); + if (ret < 0) + return ret; + + /* Now create an adapter for each channel */ + for (num = 0; num < chip->nchans; num++) { + ret = i2c_mux_add_adapter(muxc, 0, num, 0); + if (ret) { + i2c_mux_del_adapters(muxc); + return ret; + } + } + + dev_info(&client->dev, + "registered %d multiplexed busses for I2C switch %s\n", + num, client->name); + + return 0; +} + +static int ltc4306_remove(struct i2c_client *client) +{ + struct i2c_mux_core *muxc = i2c_get_clientdata(client); + + i2c_mux_del_adapters(muxc); + + return 0; +} + +static struct i2c_driver ltc4306_driver = { + .driver = { + .name = "ltc4306", + .of_match_table = of_match_ptr(ltc4306_of_match), + }, + .probe = ltc4306_probe, + .remove = ltc4306_remove, + .id_table = ltc4306_id, +}; + +module_i2c_driver(ltc4306_driver); + +MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>"); +MODULE_DESCRIPTION("Linear Technology LTC4306, LTC4305 I2C mux/switch driver"); +MODULE_LICENSE("GPL v2"); -- 2.7.4 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v5 2/2] i2c: mux: ltc4306: LTC4306 and LTC4305 I2C multiplexer/switch @ 2017-04-11 12:16 ` michael.hennerich 0 siblings, 0 replies; 7+ messages in thread From: michael.hennerich @ 2017-04-11 12:16 UTC (permalink / raw) To: wsa, peda, robh+dt, mark.rutland, linus.walleij Cc: linux-i2c, devicetree, linux-gpio, linux-kernel, Michael Hennerich From: Michael Hennerich <michael.hennerich@analog.com> This patch adds support for the Analog Devices / Linear Technology LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches. The LTC4306 optionally provides two general purpose input/output pins (GPIOs) that can be configured as logic inputs, opendrain outputs or push-pull outputs via the generic GPIOLIB framework. Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> --- Changes since v1: - Sort makefile entries - Sort driver includes - Use proper defines - Miscellaneous coding style fixups - Rename mux select callback - Revise i2c-mux-idle-disconnect handling - Add ENABLE GPIO handling on error and device removal. - Remove surplus of_match_device call. Changes since v2: - Stop double error reporting (i2c_mux_add_adapter) - Change subject - Split dt bindings to separate patch Changes since v3: - Change subject and add spaces - Convert to I2C_MUX_LOCKED - Convert to regmap - Remove local register cache - Restore previous ENABLE GPIO handling - Initially pulse ENABLE low - Eliminate i2c client struct in driver state structure - Simplify error return path - Misc minor cleanups Changes since v4: - Remove redundant includes - Use regmap cache type REGCACHE_FLAT - gpio_get restore double negates on return - Implement gpio_get_direction - Use unified device property interface - mux_alloc exact number of channels - Reword kconfig help text --- MAINTAINERS | 8 + drivers/i2c/muxes/Kconfig | 11 ++ drivers/i2c/muxes/Makefile | 1 + drivers/i2c/muxes/i2c-mux-ltc4306.c | 322 ++++++++++++++++++++++++++++++++++++ 4 files changed, 342 insertions(+) create mode 100644 drivers/i2c/muxes/i2c-mux-ltc4306.c diff --git a/MAINTAINERS b/MAINTAINERS index c776906..9a27a19 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -7698,6 +7698,14 @@ S: Maintained F: Documentation/hwmon/ltc4261 F: drivers/hwmon/ltc4261.c +LTC4306 I2C MULTIPLEXER DRIVER +M: Michael Hennerich <michael.hennerich@analog.com> +W: http://ez.analog.com/community/linux-device-drivers +L: linux-i2c@vger.kernel.org +S: Supported +F: drivers/i2c/muxes/i2c-mux-ltc4306.c +F: Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt + LTP (Linux Test Project) M: Mike Frysinger <vapier@gentoo.org> M: Cyril Hrubis <chrubis@suse.cz> diff --git a/drivers/i2c/muxes/Kconfig b/drivers/i2c/muxes/Kconfig index 10b3d17..1e160fc 100644 --- a/drivers/i2c/muxes/Kconfig +++ b/drivers/i2c/muxes/Kconfig @@ -30,6 +30,17 @@ config I2C_MUX_GPIO This driver can also be built as a module. If so, the module will be called i2c-mux-gpio. +config I2C_MUX_LTC4306 + tristate "LTC LTC4306/5 I2C multiplexer" + select GPIOLIB + select REGMAP_I2C + help + If you say yes here you get support for the Analog Devices + LTC4306 or LTC4305 I2C mux/switch devices. + + This driver can also be built as a module. If so, the module + will be called i2c-mux-ltc4306. + config I2C_MUX_PCA9541 tristate "NXP PCA9541 I2C Master Selector" help diff --git a/drivers/i2c/muxes/Makefile b/drivers/i2c/muxes/Makefile index 9948fa4..ff7618c 100644 --- a/drivers/i2c/muxes/Makefile +++ b/drivers/i2c/muxes/Makefile @@ -6,6 +6,7 @@ obj-$(CONFIG_I2C_ARB_GPIO_CHALLENGE) += i2c-arb-gpio-challenge.o obj-$(CONFIG_I2C_DEMUX_PINCTRL) += i2c-demux-pinctrl.o obj-$(CONFIG_I2C_MUX_GPIO) += i2c-mux-gpio.o +obj-$(CONFIG_I2C_MUX_LTC4306) += i2c-mux-ltc4306.o obj-$(CONFIG_I2C_MUX_MLXCPLD) += i2c-mux-mlxcpld.o obj-$(CONFIG_I2C_MUX_PCA9541) += i2c-mux-pca9541.o obj-$(CONFIG_I2C_MUX_PCA954x) += i2c-mux-pca954x.o diff --git a/drivers/i2c/muxes/i2c-mux-ltc4306.c b/drivers/i2c/muxes/i2c-mux-ltc4306.c new file mode 100644 index 0000000..311b1cc --- /dev/null +++ b/drivers/i2c/muxes/i2c-mux-ltc4306.c @@ -0,0 +1,322 @@ +/* + * Linear Technology LTC4306 and LTC4305 I2C multiplexer/switch + * + * Copyright (C) 2017 Analog Devices Inc. + * + * Licensed under the GPL-2. + * + * Based on: i2c-mux-pca954x.c + * + * Datasheet: http://cds.linear.com/docs/en/datasheet/4306.pdf + */ + +#include <linux/gpio/consumer.h> +#include <linux/gpio/driver.h> +#include <linux/i2c-mux.h> +#include <linux/i2c.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/property.h> +#include <linux/regmap.h> +#include <linux/slab.h> + +#define LTC4305_MAX_NCHANS 2 +#define LTC4306_MAX_NCHANS 4 + +#define LTC_REG_STATUS 0x0 +#define LTC_REG_CONFIG 0x1 +#define LTC_REG_MODE 0x2 +#define LTC_REG_SWITCH 0x3 + +#define LTC_DOWNSTREAM_ACCL_EN BIT(6) +#define LTC_UPSTREAM_ACCL_EN BIT(7) + +#define LTC_GPIO_ALL_INPUT 0xC0 +#define LTC_SWITCH_MASK 0xF0 + +enum ltc_type { + ltc_4305, + ltc_4306, +}; + +struct chip_desc { + u8 nchans; + u8 num_gpios; +}; + +struct ltc4306 { + struct regmap *regmap; + struct gpio_chip gpiochip; + const struct chip_desc *chip; +}; + +static const struct chip_desc chips[] = { + [ltc_4305] = { + .nchans = LTC4305_MAX_NCHANS, + }, + [ltc_4306] = { + .nchans = LTC4306_MAX_NCHANS, + .num_gpios = 2, + }, +}; + +static bool ltc4306_is_volatile_reg(struct device *dev, unsigned int reg) +{ + return (reg == LTC_REG_CONFIG) ? true : false; +} + +static const struct regmap_config ltc4306_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = LTC_REG_SWITCH, + .volatile_reg = ltc4306_is_volatile_reg, + .cache_type = REGCACHE_FLAT, +}; + +static int ltc4306_gpio_get(struct gpio_chip *chip, unsigned int offset) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + unsigned int val; + int ret; + + ret = regmap_read(data->regmap, LTC_REG_CONFIG, &val); + if (ret < 0) + return ret; + + return !!(val & BIT(1 - offset)); +} + +static void ltc4306_gpio_set(struct gpio_chip *chip, unsigned int offset, + int value) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + + regmap_update_bits(data->regmap, LTC_REG_CONFIG, BIT(5 - offset), + value ? BIT(5 - offset) : 0); +} + +static int ltc4306_gpio_get_direction(struct gpio_chip *chip, + unsigned int offset) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + unsigned int val; + int ret; + + ret = regmap_read(data->regmap, LTC_REG_MODE, &val); + if (ret < 0) + return ret; + + return !!(val & BIT(7 - offset)); +} + +static int ltc4306_gpio_direction_input(struct gpio_chip *chip, + unsigned int offset) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + + return regmap_update_bits(data->regmap, LTC_REG_MODE, + BIT(7 - offset), BIT(7 - offset)); +} + +static int ltc4306_gpio_direction_output(struct gpio_chip *chip, + unsigned int offset, int value) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + + ltc4306_gpio_set(chip, offset, value); + return regmap_update_bits(data->regmap, LTC_REG_MODE, + BIT(7 - offset), 0); +} + +static int ltc4306_gpio_set_config(struct gpio_chip *chip, + unsigned int offset, unsigned long config) +{ + struct ltc4306 *data = gpiochip_get_data(chip); + unsigned int val; + + switch (pinconf_to_config_param(config)) { + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + val = 0; + break; + case PIN_CONFIG_DRIVE_PUSH_PULL: + val = BIT(4 - offset); + break; + default: + return -ENOTSUPP; + } + + return regmap_update_bits(data->regmap, LTC_REG_MODE, + BIT(4 - offset), val); +} + +static int ltc4306_gpio_init(struct ltc4306 *data) +{ + struct device *dev = regmap_get_device(data->regmap); + + if (!data->chip->num_gpios) + return 0; + + data->gpiochip.label = dev_name(dev); + data->gpiochip.base = -1; + data->gpiochip.ngpio = data->chip->num_gpios; + data->gpiochip.parent = dev; + data->gpiochip.can_sleep = true; + data->gpiochip.get_direction = ltc4306_gpio_get_direction; + data->gpiochip.direction_input = ltc4306_gpio_direction_input; + data->gpiochip.direction_output = ltc4306_gpio_direction_output; + data->gpiochip.get = ltc4306_gpio_get; + data->gpiochip.set = ltc4306_gpio_set; + data->gpiochip.set_config = ltc4306_gpio_set_config; + data->gpiochip.owner = THIS_MODULE; + + /* gpiolib assumes all GPIOs default input */ + regmap_write(data->regmap, LTC_REG_MODE, LTC_GPIO_ALL_INPUT); + + return devm_gpiochip_add_data(dev, &data->gpiochip, data); +} + +static int ltc4306_select_mux(struct i2c_mux_core *muxc, u32 chan) +{ + struct ltc4306 *data = i2c_mux_priv(muxc); + + return regmap_update_bits(data->regmap, LTC_REG_SWITCH, + LTC_SWITCH_MASK, BIT(7 - chan)); +} + +static int ltc4306_deselect_mux(struct i2c_mux_core *muxc, u32 chan) +{ + struct ltc4306 *data = i2c_mux_priv(muxc); + + return regmap_update_bits(data->regmap, LTC_REG_SWITCH, + LTC_SWITCH_MASK, 0); +} + +static const struct i2c_device_id ltc4306_id[] = { + { "ltc4305", ltc_4305 }, + { "ltc4306", ltc_4306 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, ltc4306_id); + +static const struct of_device_id ltc4306_of_match[] = { + { .compatible = "lltc,ltc4305", .data = &chips[ltc_4305] }, + { .compatible = "lltc,ltc4306", .data = &chips[ltc_4306] }, + { } +}; +MODULE_DEVICE_TABLE(of, ltc4306_of_match); + +static int ltc4306_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct i2c_adapter *adap = to_i2c_adapter(client->dev.parent); + const struct chip_desc *chip; + struct i2c_mux_core *muxc; + struct ltc4306 *data; + struct gpio_desc *gpio; + bool idle_disc; + unsigned int val = 0; + int num, ret; + + chip = of_device_get_match_data(&client->dev); + + if (!chip) + chip = &chips[id->driver_data]; + + idle_disc = device_property_read_bool(&client->dev, + "i2c-mux-idle-disconnect"); + + muxc = i2c_mux_alloc(adap, &client->dev, + chip->nchans, sizeof(*data), + I2C_MUX_LOCKED, ltc4306_select_mux, + idle_disc ? ltc4306_deselect_mux : NULL); + if (!muxc) + return -ENOMEM; + data = i2c_mux_priv(muxc); + data->chip = chip; + + i2c_set_clientdata(client, muxc); + + data->regmap = devm_regmap_init_i2c(client, <c4306_regmap_config); + if (IS_ERR(data->regmap)) { + ret = PTR_ERR(data->regmap); + dev_err(&client->dev, "Failed to allocate register map: %d\n", + ret); + return ret; + } + + /* Reset and enable the mux if an enable GPIO is specified. */ + gpio = devm_gpiod_get_optional(&client->dev, "enable", GPIOD_OUT_LOW); + if (IS_ERR(gpio)) + return PTR_ERR(gpio); + + if (gpio) { + udelay(1); + gpiod_set_value(gpio, 1); + } + + /* + * Write the mux register at addr to verify + * that the mux is in fact present. This also + * initializes the mux to disconnected state. + */ + if (regmap_write(data->regmap, LTC_REG_SWITCH, 0) < 0) { + dev_warn(&client->dev, "probe failed\n"); + return -ENODEV; + } + + if (device_property_read_bool(&client->dev, + "ltc,downstream-accelerators-enable")) + val |= LTC_DOWNSTREAM_ACCL_EN; + + if (device_property_read_bool(&client->dev, + "ltc,upstream-accelerators-enable")) + val |= LTC_UPSTREAM_ACCL_EN; + + if (regmap_write(data->regmap, LTC_REG_CONFIG, val) < 0) + return -ENODEV; + + ret = ltc4306_gpio_init(data); + if (ret < 0) + return ret; + + /* Now create an adapter for each channel */ + for (num = 0; num < chip->nchans; num++) { + ret = i2c_mux_add_adapter(muxc, 0, num, 0); + if (ret) { + i2c_mux_del_adapters(muxc); + return ret; + } + } + + dev_info(&client->dev, + "registered %d multiplexed busses for I2C switch %s\n", + num, client->name); + + return 0; +} + +static int ltc4306_remove(struct i2c_client *client) +{ + struct i2c_mux_core *muxc = i2c_get_clientdata(client); + + i2c_mux_del_adapters(muxc); + + return 0; +} + +static struct i2c_driver ltc4306_driver = { + .driver = { + .name = "ltc4306", + .of_match_table = of_match_ptr(ltc4306_of_match), + }, + .probe = ltc4306_probe, + .remove = ltc4306_remove, + .id_table = ltc4306_id, +}; + +module_i2c_driver(ltc4306_driver); + +MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>"); +MODULE_DESCRIPTION("Linear Technology LTC4306, LTC4305 I2C mux/switch driver"); +MODULE_LICENSE("GPL v2"); -- 2.7.4 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v5 2/2] i2c: mux: ltc4306: LTC4306 and LTC4305 I2C multiplexer/switch 2017-04-11 12:16 ` michael.hennerich (?) @ 2017-04-12 8:26 ` Linus Walleij 2017-04-12 16:53 ` Peter Rosin -1 siblings, 1 reply; 7+ messages in thread From: Linus Walleij @ 2017-04-12 8:26 UTC (permalink / raw) To: Michael Hennerich Cc: Wolfram Sang, Peter Rosin, Rob Herring, Mark Rutland, linux-i2c, devicetree, linux-gpio, linux-kernel On Tue, Apr 11, 2017 at 2:16 PM, <michael.hennerich@analog.com> wrote: > From: Michael Hennerich <michael.hennerich@analog.com> > > This patch adds support for the Analog Devices / Linear Technology > LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches. > The LTC4306 optionally provides two general purpose input/output pins > (GPIOs) that can be configured as logic inputs, opendrain outputs or > push-pull outputs via the generic GPIOLIB framework. > > Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> (...) > Changes since v4: Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Please go ahead and merge to the i2c tree if you like. Yours, Linus Walleij ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v5 2/2] i2c: mux: ltc4306: LTC4306 and LTC4305 I2C multiplexer/switch 2017-04-12 8:26 ` Linus Walleij @ 2017-04-12 16:53 ` Peter Rosin 2017-04-13 6:58 ` Michael Hennerich 0 siblings, 1 reply; 7+ messages in thread From: Peter Rosin @ 2017-04-12 16:53 UTC (permalink / raw) To: Linus Walleij, Michael Hennerich Cc: Wolfram Sang, Rob Herring, Mark Rutland, linux-i2c, devicetree, linux-gpio, linux-kernel On 2017-04-12 10:26, Linus Walleij wrote: > On Tue, Apr 11, 2017 at 2:16 PM, <michael.hennerich@analog.com> wrote: > >> From: Michael Hennerich <michael.hennerich@analog.com> >> >> This patch adds support for the Analog Devices / Linear Technology >> LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches. >> The LTC4306 optionally provides two general purpose input/output pins >> (GPIOs) that can be configured as logic inputs, opendrain outputs or >> push-pull outputs via the generic GPIOLIB framework. Great, thanks for your contribution Michael! Both patches pushed to the for-next branch of the i2c-mux tree. >> Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> > (...) >> Changes since v4: > > Reviewed-by: Linus Walleij <linus.walleij@linaro.org> > > Please go ahead and merge to the i2c tree if you like. Yup, thanks for the review! (But not merged directly to the i2c tree, although they will get there eventually...) Cheers, peda ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v5 2/2] i2c: mux: ltc4306: LTC4306 and LTC4305 I2C multiplexer/switch 2017-04-12 16:53 ` Peter Rosin @ 2017-04-13 6:58 ` Michael Hennerich 0 siblings, 0 replies; 7+ messages in thread From: Michael Hennerich @ 2017-04-13 6:58 UTC (permalink / raw) To: Peter Rosin, Linus Walleij Cc: Wolfram Sang, Rob Herring, Mark Rutland, linux-i2c, devicetree, linux-gpio, linux-kernel On 12.04.2017 18:53, Peter Rosin wrote: > On 2017-04-12 10:26, Linus Walleij wrote: >> On Tue, Apr 11, 2017 at 2:16 PM, <michael.hennerich@analog.com> wrote: >> >>> From: Michael Hennerich <michael.hennerich@analog.com> >>> >>> This patch adds support for the Analog Devices / Linear Technology >>> LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches. >>> The LTC4306 optionally provides two general purpose input/output pins >>> (GPIOs) that can be configured as logic inputs, opendrain outputs or >>> push-pull outputs via the generic GPIOLIB framework. > > Great, thanks for your contribution Michael! Both patches pushed to the > for-next branch of the i2c-mux tree. > >>> Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> >> (...) >>> Changes since v4: >> >> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> >> >> Please go ahead and merge to the i2c tree if you like. > > Yup, thanks for the review! (But not merged directly to the i2c tree, > although they will get there eventually...) > > Cheers, > peda > > Peter and Linus, Thanks for your precious time - really appreciated! -- Greetings, Michael -- Analog Devices GmbH Otl-Aicher Strasse 60-64 80807 München Sitz der Gesellschaft München, Registergericht München HRB 40368, Geschäftsführer: Peter Kolberg, Ali Raza Husain, Eileen Wynne ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2017-04-13 6:57 UTC | newest] Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2017-04-11 12:16 [PATCH v5 1/2] dt-bindings: i2c: mux: ltc4306: Add dt-bindings for I2C multiplexer/switch michael.hennerich 2017-04-11 12:16 ` michael.hennerich 2017-04-11 12:16 ` [PATCH v5 2/2] i2c: mux: ltc4306: LTC4306 and LTC4305 " michael.hennerich 2017-04-11 12:16 ` michael.hennerich 2017-04-12 8:26 ` Linus Walleij 2017-04-12 16:53 ` Peter Rosin 2017-04-13 6:58 ` Michael Hennerich
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.