[PATCH v5 0/4] Mediatek MT2712 NAND FLASH Controller driver

[PATCH v5 0/4] Mediatek MT2712 NAND FLASH Controller driver

[Xiaolei Li]

The following patch-set adds support for Mediatek MT2712 NAND FLASH
Controller.

Changes on v5 relative to:
--------------------

tree    : https://github.com/bbrezillon/linux-0day
branch  : nand/next
commit  :
        'commit 2b12c057cc28 ("mtd: nand: brcmnand: Check flash #WP pin
         status before nand erase/program")'

Patch v5:
---------
- rename variable j as closest_spare in function mtk_nfc_set_spare_per_sector
- remove unneeded parenthesis
- add define MTK_NFC_MIN_SPARE to check whether there is no entry that is
  less than *sps.

Patch v4:
---------
- remove spare size array sort. iterate over all entries of spare size
  table and pick the best one.

Patch v3:
---------
- separate patches into 4.
- rename struct mtk_ecc_devdata and struct mtk_nfc_devdata to struct
  mtk_ecc_caps and struct mtk_nfc_caps respectively.
- add variables const u8 *ecc_strength and u8 num_ecc_strength into struct
  mtk_ecc_caps, and remove u8 max_ecc_strength.
- rename variabl u32 temp in function mtk_ecc_probe to u32 max_eccdata_size.
- remove ECC_CNFG_xBIT define, use a for loop to do ecc hw configuration.
- remove const u32 *spare_format from struct mtk_nfc_caps, and add variables
  u8 num_spare_size and u8 pageformat_spare_shift.
- remove PAGEFMT_SPARE_ define, use a for loop to do nfc hw configuration.
- sort spare size array before setting spare size.
- fix coding style issue.

Patch v2:
---------
- sperate patches into 3.
- refine DT bindings documentation about NFC and ECC compatible.
- use ecc->devdata->encode_parity_reg0 and ecc->devdata->err_mask
  directly, but hide them in define.

Tests:
------

* ubifs and jffs2 are validated on NAND device MT29F16G08ADBCA
  by 'dd' command.
* all drivers/mtd/tests/* pass.
* speed test:
  eraseblock write speed is 8318 KiB/s
  eraseblock read speed is 11374 KiB/s
  page write speed is 8155 KiB/s
  page read speed is 11290 KiB/s
  2 page write speed is 8217 KiB/s
  2 page read speed is 11354 KiB/s
  erase speed is 116472 KiB/s
  2x multi-block erase speed is 352978 KiB/s
  4x multi-block erase speed is 359750 KiB/s
  8x multi-block erase speed is 361484 KiB/s
  16x multi-block erase speed is 364116 KiB/s
  32x multi-block erase speed is 364116 KiB/s
  64x multi-block erase speed is 364116 KiB/s

Xiaolei Li (4):
  mtd: nand: mediatek: update DT bindings
  mtd: nand: mediatek: refine register NFI_PAGEFMT setting
  mtd: nand: mediatek: add support for different MTK NAND FLASH
    Controller IP
  mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller

 Documentation/devicetree/bindings/mtd/mtk-nand.txt |   5 +-
 drivers/mtd/nand/mtk_ecc.c                         | 218 ++++++++++-----------
 drivers/mtd/nand/mtk_ecc.h                         |   2 +-
 drivers/mtd/nand/mtk_nand.c                        | 187 +++++++++---------
 4 files changed, 206 insertions(+), 206 deletions(-)

--
1.9.1

[PATCH v5 0/4] Mediatek MT2712 NAND FLASH Controller driver

[Xiaolei Li]

The following patch-set adds support for Mediatek MT2712 NAND FLASH
Controller.

Changes on v5 relative to:
--------------------

tree    : https://github.com/bbrezillon/linux-0day
branch  : nand/next
commit  :
        'commit 2b12c057cc28 ("mtd: nand: brcmnand: Check flash #WP pin
         status before nand erase/program")'

Patch v5:
---------
- rename variable j as closest_spare in function mtk_nfc_set_spare_per_sector
- remove unneeded parenthesis
- add define MTK_NFC_MIN_SPARE to check whether there is no entry that is
  less than *sps.

Patch v4:
---------
- remove spare size array sort. iterate over all entries of spare size
  table and pick the best one.

Patch v3:
---------
- separate patches into 4.
- rename struct mtk_ecc_devdata and struct mtk_nfc_devdata to struct
  mtk_ecc_caps and struct mtk_nfc_caps respectively.
- add variables const u8 *ecc_strength and u8 num_ecc_strength into struct
  mtk_ecc_caps, and remove u8 max_ecc_strength.
- rename variabl u32 temp in function mtk_ecc_probe to u32 max_eccdata_size.
- remove ECC_CNFG_xBIT define, use a for loop to do ecc hw configuration.
- remove const u32 *spare_format from struct mtk_nfc_caps, and add variables
  u8 num_spare_size and u8 pageformat_spare_shift.
- remove PAGEFMT_SPARE_ define, use a for loop to do nfc hw configuration.
- sort spare size array before setting spare size.
- fix coding style issue.

Patch v2:
---------
- sperate patches into 3.
- refine DT bindings documentation about NFC and ECC compatible.
- use ecc->devdata->encode_parity_reg0 and ecc->devdata->err_mask
  directly, but hide them in define.

Tests:
------

* ubifs and jffs2 are validated on NAND device MT29F16G08ADBCA
  by 'dd' command.
* all drivers/mtd/tests/* pass.
* speed test:
  eraseblock write speed is 8318 KiB/s
  eraseblock read speed is 11374 KiB/s
  page write speed is 8155 KiB/s
  page read speed is 11290 KiB/s
  2 page write speed is 8217 KiB/s
  2 page read speed is 11354 KiB/s
  erase speed is 116472 KiB/s
  2x multi-block erase speed is 352978 KiB/s
  4x multi-block erase speed is 359750 KiB/s
  8x multi-block erase speed is 361484 KiB/s
  16x multi-block erase speed is 364116 KiB/s
  32x multi-block erase speed is 364116 KiB/s
  64x multi-block erase speed is 364116 KiB/s

Xiaolei Li (4):
  mtd: nand: mediatek: update DT bindings
  mtd: nand: mediatek: refine register NFI_PAGEFMT setting
  mtd: nand: mediatek: add support for different MTK NAND FLASH
    Controller IP
  mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller

 Documentation/devicetree/bindings/mtd/mtk-nand.txt |   5 +-
 drivers/mtd/nand/mtk_ecc.c                         | 218 ++++++++++-----------
 drivers/mtd/nand/mtk_ecc.h                         |   2 +-
 drivers/mtd/nand/mtk_nand.c                        | 187 +++++++++---------
 4 files changed, 206 insertions(+), 206 deletions(-)

--
1.9.1

[PATCH v5 1/4] mtd: nand: mediatek: update DT bindings

[Xiaolei Li]

Add MT2712 NAND Flash Controller dt bindings documentation.

Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
---
 Documentation/devicetree/bindings/mtd/mtk-nand.txt | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
index 069c192..dbf9e05 100644
--- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
@@ -12,7 +12,8 @@ tree nodes.
 
 The first part of NFC is NAND Controller Interface (NFI) HW.
 Required NFI properties:
-- compatible:			Should be "mediatek,mtxxxx-nfc".
+- compatible:			Should be one of "mediatek,mt2701-nfc",
+				"mediatek,mt2712-nfc".
 - reg:				Base physical address and size of NFI.
 - interrupts:			Interrupts of NFI.
 - clocks:			NFI required clocks.
@@ -141,7 +142,7 @@ Example:
 ==============
 
 Required BCH properties:
-- compatible:	Should be "mediatek,mtxxxx-ecc".
+- compatible:	Should be one of "mediatek,mt2701-ecc", "mediatek,mt2712-ecc".
 - reg:		Base physical address and size of ECC.
 - interrupts:	Interrupts of ECC.
 - clocks:	ECC required clocks.
-- 
1.9.1

[PATCH v5 1/4] mtd: nand: mediatek: update DT bindings

[Xiaolei Li]

Add MT2712 NAND Flash Controller dt bindings documentation.

Signed-off-by: Xiaolei Li <xiaolei.li-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
Reviewed-by: Matthias Brugger <matthias.bgg-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
 Documentation/devicetree/bindings/mtd/mtk-nand.txt | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
index 069c192..dbf9e05 100644
--- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
@@ -12,7 +12,8 @@ tree nodes.
 
 The first part of NFC is NAND Controller Interface (NFI) HW.
 Required NFI properties:
-- compatible:			Should be "mediatek,mtxxxx-nfc".
+- compatible:			Should be one of "mediatek,mt2701-nfc",
+				"mediatek,mt2712-nfc".
 - reg:				Base physical address and size of NFI.
 - interrupts:			Interrupts of NFI.
 - clocks:			NFI required clocks.
@@ -141,7 +142,7 @@ Example:
 ==============
 
 Required BCH properties:
-- compatible:	Should be "mediatek,mtxxxx-ecc".
+- compatible:	Should be one of "mediatek,mt2701-ecc", "mediatek,mt2712-ecc".
 - reg:		Base physical address and size of ECC.
 - interrupts:	Interrupts of ECC.
 - clocks:	ECC required clocks.
-- 
1.9.1

[PATCH v5 2/4] mtd: nand: mediatek: refine register NFI_PAGEFMT setting

[Xiaolei Li]

The register NFI_PAGEFMT is always 32 bits length, so it is better to
do register program using writel() compare with writew().

Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
---
 drivers/mtd/nand/mtk_nand.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c
index 6c517c6..c28f4b7 100644
--- a/drivers/mtd/nand/mtk_nand.c
+++ b/drivers/mtd/nand/mtk_nand.c
@@ -408,7 +408,7 @@ static int mtk_nfc_hw_runtime_config(struct mtd_info *mtd)
 
 	fmt |= mtk_nand->fdm.reg_size << PAGEFMT_FDM_SHIFT;
 	fmt |= mtk_nand->fdm.ecc_size << PAGEFMT_FDM_ECC_SHIFT;
-	nfi_writew(nfc, fmt, NFI_PAGEFMT);
+	nfi_writel(nfc, fmt, NFI_PAGEFMT);
 
 	nfc->ecc_cfg.strength = chip->ecc.strength;
 	nfc->ecc_cfg.len = chip->ecc.size + mtk_nand->fdm.ecc_size;
@@ -1009,7 +1009,7 @@ static inline void mtk_nfc_hw_init(struct mtk_nfc *nfc)
 	 * 0  : poll the status of the busy/ready signal after [7:4]*16 cycles.
 	 */
 	nfi_writew(nfc, 0xf1, NFI_CNRNB);
-	nfi_writew(nfc, PAGEFMT_8K_16K, NFI_PAGEFMT);
+	nfi_writel(nfc, PAGEFMT_8K_16K, NFI_PAGEFMT);
 
 	mtk_nfc_hw_reset(nfc);
 
-- 
1.9.1

[PATCH v5 2/4] mtd: nand: mediatek: refine register NFI_PAGEFMT setting

[Xiaolei Li]

The register NFI_PAGEFMT is always 32 bits length, so it is better to
do register program using writel() compare with writew().

Signed-off-by: Xiaolei Li <xiaolei.li-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
---
 drivers/mtd/nand/mtk_nand.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c
index 6c517c6..c28f4b7 100644
--- a/drivers/mtd/nand/mtk_nand.c
+++ b/drivers/mtd/nand/mtk_nand.c
@@ -408,7 +408,7 @@ static int mtk_nfc_hw_runtime_config(struct mtd_info *mtd)
 
 	fmt |= mtk_nand->fdm.reg_size << PAGEFMT_FDM_SHIFT;
 	fmt |= mtk_nand->fdm.ecc_size << PAGEFMT_FDM_ECC_SHIFT;
-	nfi_writew(nfc, fmt, NFI_PAGEFMT);
+	nfi_writel(nfc, fmt, NFI_PAGEFMT);
 
 	nfc->ecc_cfg.strength = chip->ecc.strength;
 	nfc->ecc_cfg.len = chip->ecc.size + mtk_nand->fdm.ecc_size;
@@ -1009,7 +1009,7 @@ static inline void mtk_nfc_hw_init(struct mtk_nfc *nfc)
 	 * 0  : poll the status of the busy/ready signal after [7:4]*16 cycles.
 	 */
 	nfi_writew(nfc, 0xf1, NFI_CNRNB);
-	nfi_writew(nfc, PAGEFMT_8K_16K, NFI_PAGEFMT);
+	nfi_writel(nfc, PAGEFMT_8K_16K, NFI_PAGEFMT);
 
 	mtk_nfc_hw_reset(nfc);
 
-- 
1.9.1

[PATCH v5 3/4] mtd: nand: mediatek: add support for different MTK NAND FLASH Controller IP

[Xiaolei Li]

ECC strength and spare size supported may be different among MTK NAND
FLASH Controller IPs.

This patch contains changes as following:
(1) add new struct mtk_nfc_caps to support different spare size.
(2) add new struct mtk_ecc_caps to support different ecc strength.
(3) remove ECC_CNFG_xBIT define, use a for loop to do ecc strength config.
(4) remove PAGEFMT_SPARE_ define, use a for loop to do spare format config.
(5) malloc ecc->eccdata buffer according to max ecc strength of this IP.

Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
---
 drivers/mtd/nand/mtk_ecc.c  | 181 ++++++++++++++++++--------------------------
 drivers/mtd/nand/mtk_ecc.h  |   2 +-
 drivers/mtd/nand/mtk_nand.c | 169 +++++++++++++++++++----------------------
 3 files changed, 153 insertions(+), 199 deletions(-)

diff --git a/drivers/mtd/nand/mtk_ecc.c b/drivers/mtd/nand/mtk_ecc.c
index dbf2562..ae51303 100644
--- a/drivers/mtd/nand/mtk_ecc.c
+++ b/drivers/mtd/nand/mtk_ecc.c
@@ -33,26 +33,6 @@
 
 #define ECC_ENCCON		(0x00)
 #define ECC_ENCCNFG		(0x04)
-#define		ECC_CNFG_4BIT		(0)
-#define		ECC_CNFG_6BIT		(1)
-#define		ECC_CNFG_8BIT		(2)
-#define		ECC_CNFG_10BIT		(3)
-#define		ECC_CNFG_12BIT		(4)
-#define		ECC_CNFG_14BIT		(5)
-#define		ECC_CNFG_16BIT		(6)
-#define		ECC_CNFG_18BIT		(7)
-#define		ECC_CNFG_20BIT		(8)
-#define		ECC_CNFG_22BIT		(9)
-#define		ECC_CNFG_24BIT		(0xa)
-#define		ECC_CNFG_28BIT		(0xb)
-#define		ECC_CNFG_32BIT		(0xc)
-#define		ECC_CNFG_36BIT		(0xd)
-#define		ECC_CNFG_40BIT		(0xe)
-#define		ECC_CNFG_44BIT		(0xf)
-#define		ECC_CNFG_48BIT		(0x10)
-#define		ECC_CNFG_52BIT		(0x11)
-#define		ECC_CNFG_56BIT		(0x12)
-#define		ECC_CNFG_60BIT		(0x13)
 #define		ECC_MODE_SHIFT		(5)
 #define		ECC_MS_SHIFT		(16)
 #define ECC_ENCDIADDR		(0x08)
@@ -66,7 +46,6 @@
 #define		DEC_CNFG_CORRECT	(0x3 << 12)
 #define ECC_DECIDLE		(0x10C)
 #define ECC_DECENUM0		(0x114)
-#define		ERR_MASK		(0x3f)
 #define ECC_DECDONE		(0x124)
 #define ECC_DECIRQ_EN		(0x200)
 #define ECC_DECIRQ_STA		(0x204)
@@ -78,8 +57,15 @@
 #define ECC_IRQ_REG(op)		((op) == ECC_ENCODE ? \
 					ECC_ENCIRQ_EN : ECC_DECIRQ_EN)
 
+struct mtk_ecc_caps {
+	u32 err_mask;
+	const u8 *ecc_strength;
+	u8 num_ecc_strength;
+};
+
 struct mtk_ecc {
 	struct device *dev;
+	const struct mtk_ecc_caps *caps;
 	void __iomem *regs;
 	struct clk *clk;
 
@@ -87,7 +73,13 @@ struct mtk_ecc {
 	struct mutex lock;
 	u32 sectors;
 
-	u8 eccdata[112];
+	u8 *eccdata;
+};
+
+/* ecc strength that mt2701 supports */
+static const u8 ecc_strength_mt2701[] = {
+	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+	40, 44, 48, 52, 56, 60
 };
 
 static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc,
@@ -136,77 +128,24 @@ static irqreturn_t mtk_ecc_irq(int irq, void *id)
 	return IRQ_HANDLED;
 }
 
-static void mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
+static int mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 {
-	u32 ecc_bit = ECC_CNFG_4BIT, dec_sz, enc_sz;
-	u32 reg;
-
-	switch (config->strength) {
-	case 4:
-		ecc_bit = ECC_CNFG_4BIT;
-		break;
-	case 6:
-		ecc_bit = ECC_CNFG_6BIT;
-		break;
-	case 8:
-		ecc_bit = ECC_CNFG_8BIT;
-		break;
-	case 10:
-		ecc_bit = ECC_CNFG_10BIT;
-		break;
-	case 12:
-		ecc_bit = ECC_CNFG_12BIT;
-		break;
-	case 14:
-		ecc_bit = ECC_CNFG_14BIT;
-		break;
-	case 16:
-		ecc_bit = ECC_CNFG_16BIT;
-		break;
-	case 18:
-		ecc_bit = ECC_CNFG_18BIT;
-		break;
-	case 20:
-		ecc_bit = ECC_CNFG_20BIT;
-		break;
-	case 22:
-		ecc_bit = ECC_CNFG_22BIT;
-		break;
-	case 24:
-		ecc_bit = ECC_CNFG_24BIT;
-		break;
-	case 28:
-		ecc_bit = ECC_CNFG_28BIT;
-		break;
-	case 32:
-		ecc_bit = ECC_CNFG_32BIT;
-		break;
-	case 36:
-		ecc_bit = ECC_CNFG_36BIT;
-		break;
-	case 40:
-		ecc_bit = ECC_CNFG_40BIT;
-		break;
-	case 44:
-		ecc_bit = ECC_CNFG_44BIT;
-		break;
-	case 48:
-		ecc_bit = ECC_CNFG_48BIT;
-		break;
-	case 52:
-		ecc_bit = ECC_CNFG_52BIT;
-		break;
-	case 56:
-		ecc_bit = ECC_CNFG_56BIT;
-		break;
-	case 60:
-		ecc_bit = ECC_CNFG_60BIT;
-		break;
-	default:
-		dev_err(ecc->dev, "invalid strength %d, default to 4 bits\n",
+	u32 ecc_bit, dec_sz, enc_sz;
+	u32 reg, i;
+
+	for (i = 0; i < ecc->caps->num_ecc_strength; i++) {
+		if (ecc->caps->ecc_strength[i] == config->strength)
+			break;
+	}
+
+	if (i == ecc->caps->num_ecc_strength) {
+		dev_err(ecc->dev, "invalid ecc strength %d\n",
 			config->strength);
+		return -EINVAL;
 	}
 
+	ecc_bit = i;
+
 	if (config->op == ECC_ENCODE) {
 		/* configure ECC encoder (in bits) */
 		enc_sz = config->len << 3;
@@ -232,6 +171,8 @@ static void mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 		if (config->sectors)
 			ecc->sectors = 1 << (config->sectors - 1);
 	}
+
+	return 0;
 }
 
 void mtk_ecc_get_stats(struct mtk_ecc *ecc, struct mtk_ecc_stats *stats,
@@ -247,8 +188,8 @@ void mtk_ecc_get_stats(struct mtk_ecc *ecc, struct mtk_ecc_stats *stats,
 		offset = (i >> 2) << 2;
 		err = readl(ecc->regs + ECC_DECENUM0 + offset);
 		err = err >> ((i % 4) * 8);
-		err &= ERR_MASK;
-		if (err == ERR_MASK) {
+		err &= ecc->caps->err_mask;
+		if (err == ecc->caps->err_mask) {
 			/* uncorrectable errors */
 			stats->failed++;
 			continue;
@@ -322,7 +263,11 @@ int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 	}
 
 	mtk_ecc_wait_idle(ecc, op);
-	mtk_ecc_config(ecc, config);
+
+	ret = mtk_ecc_config(ecc, config);
+	if (ret)
+		return ret;
+
 	writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op));
 
 	init_completion(&ecc->done);
@@ -409,37 +354,66 @@ int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config,
 }
 EXPORT_SYMBOL(mtk_ecc_encode);
 
-void mtk_ecc_adjust_strength(u32 *p)
+void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p)
 {
-	u32 ecc[] = {4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
-			40, 44, 48, 52, 56, 60};
+	const u8 *ecc_strength = ecc->caps->ecc_strength;
 	int i;
 
-	for (i = 0; i < ARRAY_SIZE(ecc); i++) {
-		if (*p <= ecc[i]) {
+	for (i = 0; i < ecc->caps->num_ecc_strength; i++) {
+		if (*p <= ecc_strength[i]) {
 			if (!i)
-				*p = ecc[i];
-			else if (*p != ecc[i])
-				*p = ecc[i - 1];
+				*p = ecc_strength[i];
+			else if (*p != ecc_strength[i])
+				*p = ecc_strength[i - 1];
 			return;
 		}
 	}
 
-	*p = ecc[ARRAY_SIZE(ecc) - 1];
+	*p = ecc_strength[ecc->caps->num_ecc_strength - 1];
 }
 EXPORT_SYMBOL(mtk_ecc_adjust_strength);
 
+static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = {
+	.err_mask = 0x3f,
+	.ecc_strength = ecc_strength_mt2701,
+	.num_ecc_strength = 20,
+};
+
+static const struct of_device_id mtk_ecc_dt_match[] = {
+	{
+		.compatible = "mediatek,mt2701-ecc",
+		.data = &mtk_ecc_caps_mt2701,
+	},
+	{},
+};
+
 static int mtk_ecc_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct mtk_ecc *ecc;
 	struct resource *res;
+	const struct of_device_id *of_ecc_id = NULL;
+	u32 max_eccdata_size;
 	int irq, ret;
 
 	ecc = devm_kzalloc(dev, sizeof(*ecc), GFP_KERNEL);
 	if (!ecc)
 		return -ENOMEM;
 
+	of_ecc_id = of_match_device(mtk_ecc_dt_match, &pdev->dev);
+	if (!of_ecc_id)
+		return -ENODEV;
+
+	ecc->caps = of_ecc_id->data;
+
+	max_eccdata_size = ecc->caps->num_ecc_strength - 1;
+	max_eccdata_size = ecc->caps->ecc_strength[max_eccdata_size];
+	max_eccdata_size = (max_eccdata_size * ECC_PARITY_BITS + 7) >> 3;
+	max_eccdata_size = round_up(max_eccdata_size, 4);
+	ecc->eccdata = devm_kzalloc(dev, max_eccdata_size, GFP_KERNEL);
+	if (!ecc->eccdata)
+		return -ENOMEM;
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	ecc->regs = devm_ioremap_resource(dev, res);
 	if (IS_ERR(ecc->regs)) {
@@ -508,11 +482,6 @@ static int mtk_ecc_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(mtk_ecc_pm_ops, mtk_ecc_suspend, mtk_ecc_resume);
 #endif
 
-static const struct of_device_id mtk_ecc_dt_match[] = {
-	{ .compatible = "mediatek,mt2701-ecc" },
-	{},
-};
-
 MODULE_DEVICE_TABLE(of, mtk_ecc_dt_match);
 
 static struct platform_driver mtk_ecc_driver = {
diff --git a/drivers/mtd/nand/mtk_ecc.h b/drivers/mtd/nand/mtk_ecc.h
index cbeba5c..d245c14 100644
--- a/drivers/mtd/nand/mtk_ecc.h
+++ b/drivers/mtd/nand/mtk_ecc.h
@@ -42,7 +42,7 @@ struct mtk_ecc_config {
 int mtk_ecc_wait_done(struct mtk_ecc *, enum mtk_ecc_operation);
 int mtk_ecc_enable(struct mtk_ecc *, struct mtk_ecc_config *);
 void mtk_ecc_disable(struct mtk_ecc *);
-void mtk_ecc_adjust_strength(u32 *);
+void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p);
 
 struct mtk_ecc *of_mtk_ecc_get(struct device_node *);
 void mtk_ecc_release(struct mtk_ecc *);
diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c
index c28f4b7..e428669 100644
--- a/drivers/mtd/nand/mtk_nand.c
+++ b/drivers/mtd/nand/mtk_nand.c
@@ -24,6 +24,7 @@
 #include <linux/module.h>
 #include <linux/iopoll.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include "mtk_ecc.h"
 
 /* NAND controller register definition */
@@ -38,23 +39,6 @@
 #define NFI_PAGEFMT		(0x04)
 #define		PAGEFMT_FDM_ECC_SHIFT	(12)
 #define		PAGEFMT_FDM_SHIFT	(8)
-#define		PAGEFMT_SPARE_16	(0)
-#define		PAGEFMT_SPARE_26	(1)
-#define		PAGEFMT_SPARE_27	(2)
-#define		PAGEFMT_SPARE_28	(3)
-#define		PAGEFMT_SPARE_32	(4)
-#define		PAGEFMT_SPARE_36	(5)
-#define		PAGEFMT_SPARE_40	(6)
-#define		PAGEFMT_SPARE_44	(7)
-#define		PAGEFMT_SPARE_48	(8)
-#define		PAGEFMT_SPARE_49	(9)
-#define		PAGEFMT_SPARE_50	(0xa)
-#define		PAGEFMT_SPARE_51	(0xb)
-#define		PAGEFMT_SPARE_52	(0xc)
-#define		PAGEFMT_SPARE_62	(0xd)
-#define		PAGEFMT_SPARE_63	(0xe)
-#define		PAGEFMT_SPARE_64	(0xf)
-#define		PAGEFMT_SPARE_SHIFT	(4)
 #define		PAGEFMT_SEC_SEL_512	BIT(2)
 #define		PAGEFMT_512_2K		(0)
 #define		PAGEFMT_2K_4K		(1)
@@ -115,6 +99,13 @@
 #define MTK_RESET_TIMEOUT	(1000000)
 #define MTK_MAX_SECTOR		(16)
 #define MTK_NAND_MAX_NSELS	(2)
+#define MTK_NFC_MIN_SPARE	(16)
+
+struct mtk_nfc_caps {
+	const u8 *spare_size;
+	u8 num_spare_size;
+	u8 pageformat_spare_shift;
+};
 
 struct mtk_nfc_bad_mark_ctl {
 	void (*bm_swap)(struct mtd_info *, u8 *buf, int raw);
@@ -155,6 +146,7 @@ struct mtk_nfc {
 	struct mtk_ecc *ecc;
 
 	struct device *dev;
+	const struct mtk_nfc_caps *caps;
 	void __iomem *regs;
 
 	struct completion done;
@@ -163,6 +155,15 @@ struct mtk_nfc {
 	u8 *buffer;
 };
 
+/*
+ * supported spare size of each IP.
+ * order should be the same with the spare size bitfiled defination of
+ * register NFI_PAGEFMT.
+ */
+static const u8 spare_size_mt2701[] = {
+	16, 26, 27, 28, 32, 36, 40, 44,	48, 49, 50, 51, 52, 62, 63, 64
+};
+
 static inline struct mtk_nfc_nand_chip *to_mtk_nand(struct nand_chip *nand)
 {
 	return container_of(nand, struct mtk_nfc_nand_chip, nand);
@@ -308,7 +309,7 @@ static int mtk_nfc_hw_runtime_config(struct mtd_info *mtd)
 	struct nand_chip *chip = mtd_to_nand(mtd);
 	struct mtk_nfc_nand_chip *mtk_nand = to_mtk_nand(chip);
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
-	u32 fmt, spare;
+	u32 fmt, spare, i;
 
 	if (!mtd->writesize)
 		return 0;
@@ -352,60 +353,18 @@ static int mtk_nfc_hw_runtime_config(struct mtd_info *mtd)
 	if (chip->ecc.size == 1024)
 		spare >>= 1;
 
-	switch (spare) {
-	case 16:
-		fmt |= (PAGEFMT_SPARE_16 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 26:
-		fmt |= (PAGEFMT_SPARE_26 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 27:
-		fmt |= (PAGEFMT_SPARE_27 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 28:
-		fmt |= (PAGEFMT_SPARE_28 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 32:
-		fmt |= (PAGEFMT_SPARE_32 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 36:
-		fmt |= (PAGEFMT_SPARE_36 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 40:
-		fmt |= (PAGEFMT_SPARE_40 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 44:
-		fmt |= (PAGEFMT_SPARE_44 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 48:
-		fmt |= (PAGEFMT_SPARE_48 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 49:
-		fmt |= (PAGEFMT_SPARE_49 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 50:
-		fmt |= (PAGEFMT_SPARE_50 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 51:
-		fmt |= (PAGEFMT_SPARE_51 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 52:
-		fmt |= (PAGEFMT_SPARE_52 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 62:
-		fmt |= (PAGEFMT_SPARE_62 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 63:
-		fmt |= (PAGEFMT_SPARE_63 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 64:
-		fmt |= (PAGEFMT_SPARE_64 << PAGEFMT_SPARE_SHIFT);
-		break;
-	default:
-		dev_err(nfc->dev, "invalid spare per sector %d\n", spare);
+	for (i = 0; i < nfc->caps->num_spare_size; i++) {
+		if (nfc->caps->spare_size[i] == spare)
+			break;
+	}
+
+	if (i == nfc->caps->num_spare_size) {
+		dev_err(nfc->dev, "invalid spare size %d\n", spare);
 		return -EINVAL;
 	}
 
+	fmt |= i << nfc->caps->pageformat_spare_shift;
+
 	fmt |= mtk_nand->fdm.reg_size << PAGEFMT_FDM_SHIFT;
 	fmt |= mtk_nand->fdm.ecc_size << PAGEFMT_FDM_ECC_SHIFT;
 	nfi_writel(nfc, fmt, NFI_PAGEFMT);
@@ -1131,12 +1090,12 @@ static void mtk_nfc_set_bad_mark_ctl(struct mtk_nfc_bad_mark_ctl *bm_ctl,
 	}
 }
 
-static void mtk_nfc_set_spare_per_sector(u32 *sps, struct mtd_info *mtd)
+static int mtk_nfc_set_spare_per_sector(u32 *sps, struct mtd_info *mtd)
 {
 	struct nand_chip *nand = mtd_to_nand(mtd);
-	u32 spare[] = {16, 26, 27, 28, 32, 36, 40, 44,
-			48, 49, 50, 51, 52, 62, 63, 64};
-	u32 eccsteps, i;
+	struct mtk_nfc *nfc = nand_get_controller_data(nand);
+	const u8 *spare = nfc->caps->spare_size;
+	u32 eccsteps, i, closest_spare = 0;
 
 	eccsteps = mtd->writesize / nand->ecc.size;
 	*sps = mtd->oobsize / eccsteps;
@@ -1144,28 +1103,31 @@ static void mtk_nfc_set_spare_per_sector(u32 *sps, struct mtd_info *mtd)
 	if (nand->ecc.size == 1024)
 		*sps >>= 1;
 
-	for (i = 0; i < ARRAY_SIZE(spare); i++) {
-		if (*sps <= spare[i]) {
-			if (!i)
-				*sps = spare[i];
-			else if (*sps != spare[i])
-				*sps = spare[i - 1];
-			break;
+	if (*sps < MTK_NFC_MIN_SPARE)
+		return -EINVAL;
+
+	for (i = 0; i < nfc->caps->num_spare_size; i++) {
+		if (*sps >= spare[i] && spare[i] >= spare[closest_spare]) {
+			closest_spare = i;
+			if (*sps == spare[i])
+				break;
 		}
 	}
 
-	if (i >= ARRAY_SIZE(spare))
-		*sps = spare[ARRAY_SIZE(spare) - 1];
+	*sps = spare[closest_spare];
 
 	if (nand->ecc.size == 1024)
 		*sps <<= 1;
+
+	return 0;
 }
 
 static int mtk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd)
 {
 	struct nand_chip *nand = mtd_to_nand(mtd);
+	struct mtk_nfc *nfc = nand_get_controller_data(nand);
 	u32 spare;
-	int free;
+	int free, ret;
 
 	/* support only ecc hw mode */
 	if (nand->ecc.mode != NAND_ECC_HW) {
@@ -1194,7 +1156,9 @@ static int mtk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd)
 			nand->ecc.size = 1024;
 		}
 
-		mtk_nfc_set_spare_per_sector(&spare, mtd);
+		ret = mtk_nfc_set_spare_per_sector(&spare, mtd);
+		if (ret)
+			return ret;
 
 		/* calculate oob bytes except ecc parity data */
 		free = ((nand->ecc.strength * ECC_PARITY_BITS) + 7) >> 3;
@@ -1214,7 +1178,7 @@ static int mtk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd)
 		}
 	}
 
-	mtk_ecc_adjust_strength(&nand->ecc.strength);
+	mtk_ecc_adjust_strength(nfc->ecc, &nand->ecc.strength);
 
 	dev_info(dev, "eccsize %d eccstrength %d\n",
 		 nand->ecc.size, nand->ecc.strength);
@@ -1312,7 +1276,10 @@ static int mtk_nfc_nand_chip_init(struct device *dev, struct mtk_nfc *nfc,
 		return -EINVAL;
 	}
 
-	mtk_nfc_set_spare_per_sector(&chip->spare_per_sector, mtd);
+	ret = mtk_nfc_set_spare_per_sector(&chip->spare_per_sector, mtd);
+	if (ret)
+		return ret;
+
 	mtk_nfc_set_fdm(&chip->fdm, mtd);
 	mtk_nfc_set_bad_mark_ctl(&chip->bad_mark, mtd);
 
@@ -1354,12 +1321,28 @@ static int mtk_nfc_nand_chips_init(struct device *dev, struct mtk_nfc *nfc)
 	return 0;
 }
 
+static const struct mtk_nfc_caps mtk_nfc_caps_mt2701 = {
+	.spare_size = spare_size_mt2701,
+	.num_spare_size = 16,
+	.pageformat_spare_shift = 4,
+};
+
+static const struct of_device_id mtk_nfc_id_table[] = {
+	{
+		.compatible = "mediatek,mt2701-nfc",
+		.data = &mtk_nfc_caps_mt2701,
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, mtk_nfc_id_table);
+
 static int mtk_nfc_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct device_node *np = dev->of_node;
 	struct mtk_nfc *nfc;
 	struct resource *res;
+	const struct of_device_id *of_nfc_id = NULL;
 	int ret, irq;
 
 	nfc = devm_kzalloc(dev, sizeof(*nfc), GFP_KERNEL);
@@ -1423,6 +1406,14 @@ static int mtk_nfc_probe(struct platform_device *pdev)
 		goto clk_disable;
 	}
 
+	of_nfc_id = of_match_device(mtk_nfc_id_table, &pdev->dev);
+	if (!of_nfc_id) {
+		ret = -ENODEV;
+		goto clk_disable;
+	}
+
+	nfc->caps = of_nfc_id->data;
+
 	platform_set_drvdata(pdev, nfc);
 
 	ret = mtk_nfc_nand_chips_init(dev, nfc);
@@ -1503,12 +1494,6 @@ static int mtk_nfc_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(mtk_nfc_pm_ops, mtk_nfc_suspend, mtk_nfc_resume);
 #endif
 
-static const struct of_device_id mtk_nfc_id_table[] = {
-	{ .compatible = "mediatek,mt2701-nfc" },
-	{}
-};
-MODULE_DEVICE_TABLE(of, mtk_nfc_id_table);
-
 static struct platform_driver mtk_nfc_driver = {
 	.probe  = mtk_nfc_probe,
 	.remove = mtk_nfc_remove,
-- 
1.9.1

[PATCH v5 3/4] mtd: nand: mediatek: add support for different MTK NAND FLASH Controller IP

[Xiaolei Li]

ECC strength and spare size supported may be different among MTK NAND
FLASH Controller IPs.

This patch contains changes as following:
(1) add new struct mtk_nfc_caps to support different spare size.
(2) add new struct mtk_ecc_caps to support different ecc strength.
(3) remove ECC_CNFG_xBIT define, use a for loop to do ecc strength config.
(4) remove PAGEFMT_SPARE_ define, use a for loop to do spare format config.
(5) malloc ecc->eccdata buffer according to max ecc strength of this IP.

Signed-off-by: Xiaolei Li <xiaolei.li-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
---
 drivers/mtd/nand/mtk_ecc.c  | 181 ++++++++++++++++++--------------------------
 drivers/mtd/nand/mtk_ecc.h  |   2 +-
 drivers/mtd/nand/mtk_nand.c | 169 +++++++++++++++++++----------------------
 3 files changed, 153 insertions(+), 199 deletions(-)

diff --git a/drivers/mtd/nand/mtk_ecc.c b/drivers/mtd/nand/mtk_ecc.c
index dbf2562..ae51303 100644
--- a/drivers/mtd/nand/mtk_ecc.c
+++ b/drivers/mtd/nand/mtk_ecc.c
@@ -33,26 +33,6 @@
 
 #define ECC_ENCCON		(0x00)
 #define ECC_ENCCNFG		(0x04)
-#define		ECC_CNFG_4BIT		(0)
-#define		ECC_CNFG_6BIT		(1)
-#define		ECC_CNFG_8BIT		(2)
-#define		ECC_CNFG_10BIT		(3)
-#define		ECC_CNFG_12BIT		(4)
-#define		ECC_CNFG_14BIT		(5)
-#define		ECC_CNFG_16BIT		(6)
-#define		ECC_CNFG_18BIT		(7)
-#define		ECC_CNFG_20BIT		(8)
-#define		ECC_CNFG_22BIT		(9)
-#define		ECC_CNFG_24BIT		(0xa)
-#define		ECC_CNFG_28BIT		(0xb)
-#define		ECC_CNFG_32BIT		(0xc)
-#define		ECC_CNFG_36BIT		(0xd)
-#define		ECC_CNFG_40BIT		(0xe)
-#define		ECC_CNFG_44BIT		(0xf)
-#define		ECC_CNFG_48BIT		(0x10)
-#define		ECC_CNFG_52BIT		(0x11)
-#define		ECC_CNFG_56BIT		(0x12)
-#define		ECC_CNFG_60BIT		(0x13)
 #define		ECC_MODE_SHIFT		(5)
 #define		ECC_MS_SHIFT		(16)
 #define ECC_ENCDIADDR		(0x08)
@@ -66,7 +46,6 @@
 #define		DEC_CNFG_CORRECT	(0x3 << 12)
 #define ECC_DECIDLE		(0x10C)
 #define ECC_DECENUM0		(0x114)
-#define		ERR_MASK		(0x3f)
 #define ECC_DECDONE		(0x124)
 #define ECC_DECIRQ_EN		(0x200)
 #define ECC_DECIRQ_STA		(0x204)
@@ -78,8 +57,15 @@
 #define ECC_IRQ_REG(op)		((op) == ECC_ENCODE ? \
 					ECC_ENCIRQ_EN : ECC_DECIRQ_EN)
 
+struct mtk_ecc_caps {
+	u32 err_mask;
+	const u8 *ecc_strength;
+	u8 num_ecc_strength;
+};
+
 struct mtk_ecc {
 	struct device *dev;
+	const struct mtk_ecc_caps *caps;
 	void __iomem *regs;
 	struct clk *clk;
 
@@ -87,7 +73,13 @@ struct mtk_ecc {
 	struct mutex lock;
 	u32 sectors;
 
-	u8 eccdata[112];
+	u8 *eccdata;
+};
+
+/* ecc strength that mt2701 supports */
+static const u8 ecc_strength_mt2701[] = {
+	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+	40, 44, 48, 52, 56, 60
 };
 
 static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc,
@@ -136,77 +128,24 @@ static irqreturn_t mtk_ecc_irq(int irq, void *id)
 	return IRQ_HANDLED;
 }
 
-static void mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
+static int mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 {
-	u32 ecc_bit = ECC_CNFG_4BIT, dec_sz, enc_sz;
-	u32 reg;
-
-	switch (config->strength) {
-	case 4:
-		ecc_bit = ECC_CNFG_4BIT;
-		break;
-	case 6:
-		ecc_bit = ECC_CNFG_6BIT;
-		break;
-	case 8:
-		ecc_bit = ECC_CNFG_8BIT;
-		break;
-	case 10:
-		ecc_bit = ECC_CNFG_10BIT;
-		break;
-	case 12:
-		ecc_bit = ECC_CNFG_12BIT;
-		break;
-	case 14:
-		ecc_bit = ECC_CNFG_14BIT;
-		break;
-	case 16:
-		ecc_bit = ECC_CNFG_16BIT;
-		break;
-	case 18:
-		ecc_bit = ECC_CNFG_18BIT;
-		break;
-	case 20:
-		ecc_bit = ECC_CNFG_20BIT;
-		break;
-	case 22:
-		ecc_bit = ECC_CNFG_22BIT;
-		break;
-	case 24:
-		ecc_bit = ECC_CNFG_24BIT;
-		break;
-	case 28:
-		ecc_bit = ECC_CNFG_28BIT;
-		break;
-	case 32:
-		ecc_bit = ECC_CNFG_32BIT;
-		break;
-	case 36:
-		ecc_bit = ECC_CNFG_36BIT;
-		break;
-	case 40:
-		ecc_bit = ECC_CNFG_40BIT;
-		break;
-	case 44:
-		ecc_bit = ECC_CNFG_44BIT;
-		break;
-	case 48:
-		ecc_bit = ECC_CNFG_48BIT;
-		break;
-	case 52:
-		ecc_bit = ECC_CNFG_52BIT;
-		break;
-	case 56:
-		ecc_bit = ECC_CNFG_56BIT;
-		break;
-	case 60:
-		ecc_bit = ECC_CNFG_60BIT;
-		break;
-	default:
-		dev_err(ecc->dev, "invalid strength %d, default to 4 bits\n",
+	u32 ecc_bit, dec_sz, enc_sz;
+	u32 reg, i;
+
+	for (i = 0; i < ecc->caps->num_ecc_strength; i++) {
+		if (ecc->caps->ecc_strength[i] == config->strength)
+			break;
+	}
+
+	if (i == ecc->caps->num_ecc_strength) {
+		dev_err(ecc->dev, "invalid ecc strength %d\n",
 			config->strength);
+		return -EINVAL;
 	}
 
+	ecc_bit = i;
+
 	if (config->op == ECC_ENCODE) {
 		/* configure ECC encoder (in bits) */
 		enc_sz = config->len << 3;
@@ -232,6 +171,8 @@ static void mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 		if (config->sectors)
 			ecc->sectors = 1 << (config->sectors - 1);
 	}
+
+	return 0;
 }
 
 void mtk_ecc_get_stats(struct mtk_ecc *ecc, struct mtk_ecc_stats *stats,
@@ -247,8 +188,8 @@ void mtk_ecc_get_stats(struct mtk_ecc *ecc, struct mtk_ecc_stats *stats,
 		offset = (i >> 2) << 2;
 		err = readl(ecc->regs + ECC_DECENUM0 + offset);
 		err = err >> ((i % 4) * 8);
-		err &= ERR_MASK;
-		if (err == ERR_MASK) {
+		err &= ecc->caps->err_mask;
+		if (err == ecc->caps->err_mask) {
 			/* uncorrectable errors */
 			stats->failed++;
 			continue;
@@ -322,7 +263,11 @@ int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 	}
 
 	mtk_ecc_wait_idle(ecc, op);
-	mtk_ecc_config(ecc, config);
+
+	ret = mtk_ecc_config(ecc, config);
+	if (ret)
+		return ret;
+
 	writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op));
 
 	init_completion(&ecc->done);
@@ -409,37 +354,66 @@ int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config,
 }
 EXPORT_SYMBOL(mtk_ecc_encode);
 
-void mtk_ecc_adjust_strength(u32 *p)
+void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p)
 {
-	u32 ecc[] = {4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
-			40, 44, 48, 52, 56, 60};
+	const u8 *ecc_strength = ecc->caps->ecc_strength;
 	int i;
 
-	for (i = 0; i < ARRAY_SIZE(ecc); i++) {
-		if (*p <= ecc[i]) {
+	for (i = 0; i < ecc->caps->num_ecc_strength; i++) {
+		if (*p <= ecc_strength[i]) {
 			if (!i)
-				*p = ecc[i];
-			else if (*p != ecc[i])
-				*p = ecc[i - 1];
+				*p = ecc_strength[i];
+			else if (*p != ecc_strength[i])
+				*p = ecc_strength[i - 1];
 			return;
 		}
 	}
 
-	*p = ecc[ARRAY_SIZE(ecc) - 1];
+	*p = ecc_strength[ecc->caps->num_ecc_strength - 1];
 }
 EXPORT_SYMBOL(mtk_ecc_adjust_strength);
 
+static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = {
+	.err_mask = 0x3f,
+	.ecc_strength = ecc_strength_mt2701,
+	.num_ecc_strength = 20,
+};
+
+static const struct of_device_id mtk_ecc_dt_match[] = {
+	{
+		.compatible = "mediatek,mt2701-ecc",
+		.data = &mtk_ecc_caps_mt2701,
+	},
+	{},
+};
+
 static int mtk_ecc_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct mtk_ecc *ecc;
 	struct resource *res;
+	const struct of_device_id *of_ecc_id = NULL;
+	u32 max_eccdata_size;
 	int irq, ret;
 
 	ecc = devm_kzalloc(dev, sizeof(*ecc), GFP_KERNEL);
 	if (!ecc)
 		return -ENOMEM;
 
+	of_ecc_id = of_match_device(mtk_ecc_dt_match, &pdev->dev);
+	if (!of_ecc_id)
+		return -ENODEV;
+
+	ecc->caps = of_ecc_id->data;
+
+	max_eccdata_size = ecc->caps->num_ecc_strength - 1;
+	max_eccdata_size = ecc->caps->ecc_strength[max_eccdata_size];
+	max_eccdata_size = (max_eccdata_size * ECC_PARITY_BITS + 7) >> 3;
+	max_eccdata_size = round_up(max_eccdata_size, 4);
+	ecc->eccdata = devm_kzalloc(dev, max_eccdata_size, GFP_KERNEL);
+	if (!ecc->eccdata)
+		return -ENOMEM;
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	ecc->regs = devm_ioremap_resource(dev, res);
 	if (IS_ERR(ecc->regs)) {
@@ -508,11 +482,6 @@ static int mtk_ecc_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(mtk_ecc_pm_ops, mtk_ecc_suspend, mtk_ecc_resume);
 #endif
 
-static const struct of_device_id mtk_ecc_dt_match[] = {
-	{ .compatible = "mediatek,mt2701-ecc" },
-	{},
-};
-
 MODULE_DEVICE_TABLE(of, mtk_ecc_dt_match);
 
 static struct platform_driver mtk_ecc_driver = {
diff --git a/drivers/mtd/nand/mtk_ecc.h b/drivers/mtd/nand/mtk_ecc.h
index cbeba5c..d245c14 100644
--- a/drivers/mtd/nand/mtk_ecc.h
+++ b/drivers/mtd/nand/mtk_ecc.h
@@ -42,7 +42,7 @@ struct mtk_ecc_config {
 int mtk_ecc_wait_done(struct mtk_ecc *, enum mtk_ecc_operation);
 int mtk_ecc_enable(struct mtk_ecc *, struct mtk_ecc_config *);
 void mtk_ecc_disable(struct mtk_ecc *);
-void mtk_ecc_adjust_strength(u32 *);
+void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p);
 
 struct mtk_ecc *of_mtk_ecc_get(struct device_node *);
 void mtk_ecc_release(struct mtk_ecc *);
diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c
index c28f4b7..e428669 100644
--- a/drivers/mtd/nand/mtk_nand.c
+++ b/drivers/mtd/nand/mtk_nand.c
@@ -24,6 +24,7 @@
 #include <linux/module.h>
 #include <linux/iopoll.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include "mtk_ecc.h"
 
 /* NAND controller register definition */
@@ -38,23 +39,6 @@
 #define NFI_PAGEFMT		(0x04)
 #define		PAGEFMT_FDM_ECC_SHIFT	(12)
 #define		PAGEFMT_FDM_SHIFT	(8)
-#define		PAGEFMT_SPARE_16	(0)
-#define		PAGEFMT_SPARE_26	(1)
-#define		PAGEFMT_SPARE_27	(2)
-#define		PAGEFMT_SPARE_28	(3)
-#define		PAGEFMT_SPARE_32	(4)
-#define		PAGEFMT_SPARE_36	(5)
-#define		PAGEFMT_SPARE_40	(6)
-#define		PAGEFMT_SPARE_44	(7)
-#define		PAGEFMT_SPARE_48	(8)
-#define		PAGEFMT_SPARE_49	(9)
-#define		PAGEFMT_SPARE_50	(0xa)
-#define		PAGEFMT_SPARE_51	(0xb)
-#define		PAGEFMT_SPARE_52	(0xc)
-#define		PAGEFMT_SPARE_62	(0xd)
-#define		PAGEFMT_SPARE_63	(0xe)
-#define		PAGEFMT_SPARE_64	(0xf)
-#define		PAGEFMT_SPARE_SHIFT	(4)
 #define		PAGEFMT_SEC_SEL_512	BIT(2)
 #define		PAGEFMT_512_2K		(0)
 #define		PAGEFMT_2K_4K		(1)
@@ -115,6 +99,13 @@
 #define MTK_RESET_TIMEOUT	(1000000)
 #define MTK_MAX_SECTOR		(16)
 #define MTK_NAND_MAX_NSELS	(2)
+#define MTK_NFC_MIN_SPARE	(16)
+
+struct mtk_nfc_caps {
+	const u8 *spare_size;
+	u8 num_spare_size;
+	u8 pageformat_spare_shift;
+};
 
 struct mtk_nfc_bad_mark_ctl {
 	void (*bm_swap)(struct mtd_info *, u8 *buf, int raw);
@@ -155,6 +146,7 @@ struct mtk_nfc {
 	struct mtk_ecc *ecc;
 
 	struct device *dev;
+	const struct mtk_nfc_caps *caps;
 	void __iomem *regs;
 
 	struct completion done;
@@ -163,6 +155,15 @@ struct mtk_nfc {
 	u8 *buffer;
 };
 
+/*
+ * supported spare size of each IP.
+ * order should be the same with the spare size bitfiled defination of
+ * register NFI_PAGEFMT.
+ */
+static const u8 spare_size_mt2701[] = {
+	16, 26, 27, 28, 32, 36, 40, 44,	48, 49, 50, 51, 52, 62, 63, 64
+};
+
 static inline struct mtk_nfc_nand_chip *to_mtk_nand(struct nand_chip *nand)
 {
 	return container_of(nand, struct mtk_nfc_nand_chip, nand);
@@ -308,7 +309,7 @@ static int mtk_nfc_hw_runtime_config(struct mtd_info *mtd)
 	struct nand_chip *chip = mtd_to_nand(mtd);
 	struct mtk_nfc_nand_chip *mtk_nand = to_mtk_nand(chip);
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
-	u32 fmt, spare;
+	u32 fmt, spare, i;
 
 	if (!mtd->writesize)
 		return 0;
@@ -352,60 +353,18 @@ static int mtk_nfc_hw_runtime_config(struct mtd_info *mtd)
 	if (chip->ecc.size == 1024)
 		spare >>= 1;
 
-	switch (spare) {
-	case 16:
-		fmt |= (PAGEFMT_SPARE_16 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 26:
-		fmt |= (PAGEFMT_SPARE_26 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 27:
-		fmt |= (PAGEFMT_SPARE_27 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 28:
-		fmt |= (PAGEFMT_SPARE_28 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 32:
-		fmt |= (PAGEFMT_SPARE_32 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 36:
-		fmt |= (PAGEFMT_SPARE_36 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 40:
-		fmt |= (PAGEFMT_SPARE_40 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 44:
-		fmt |= (PAGEFMT_SPARE_44 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 48:
-		fmt |= (PAGEFMT_SPARE_48 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 49:
-		fmt |= (PAGEFMT_SPARE_49 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 50:
-		fmt |= (PAGEFMT_SPARE_50 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 51:
-		fmt |= (PAGEFMT_SPARE_51 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 52:
-		fmt |= (PAGEFMT_SPARE_52 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 62:
-		fmt |= (PAGEFMT_SPARE_62 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 63:
-		fmt |= (PAGEFMT_SPARE_63 << PAGEFMT_SPARE_SHIFT);
-		break;
-	case 64:
-		fmt |= (PAGEFMT_SPARE_64 << PAGEFMT_SPARE_SHIFT);
-		break;
-	default:
-		dev_err(nfc->dev, "invalid spare per sector %d\n", spare);
+	for (i = 0; i < nfc->caps->num_spare_size; i++) {
+		if (nfc->caps->spare_size[i] == spare)
+			break;
+	}
+
+	if (i == nfc->caps->num_spare_size) {
+		dev_err(nfc->dev, "invalid spare size %d\n", spare);
 		return -EINVAL;
 	}
 
+	fmt |= i << nfc->caps->pageformat_spare_shift;
+
 	fmt |= mtk_nand->fdm.reg_size << PAGEFMT_FDM_SHIFT;
 	fmt |= mtk_nand->fdm.ecc_size << PAGEFMT_FDM_ECC_SHIFT;
 	nfi_writel(nfc, fmt, NFI_PAGEFMT);
@@ -1131,12 +1090,12 @@ static void mtk_nfc_set_bad_mark_ctl(struct mtk_nfc_bad_mark_ctl *bm_ctl,
 	}
 }
 
-static void mtk_nfc_set_spare_per_sector(u32 *sps, struct mtd_info *mtd)
+static int mtk_nfc_set_spare_per_sector(u32 *sps, struct mtd_info *mtd)
 {
 	struct nand_chip *nand = mtd_to_nand(mtd);
-	u32 spare[] = {16, 26, 27, 28, 32, 36, 40, 44,
-			48, 49, 50, 51, 52, 62, 63, 64};
-	u32 eccsteps, i;
+	struct mtk_nfc *nfc = nand_get_controller_data(nand);
+	const u8 *spare = nfc->caps->spare_size;
+	u32 eccsteps, i, closest_spare = 0;
 
 	eccsteps = mtd->writesize / nand->ecc.size;
 	*sps = mtd->oobsize / eccsteps;
@@ -1144,28 +1103,31 @@ static void mtk_nfc_set_spare_per_sector(u32 *sps, struct mtd_info *mtd)
 	if (nand->ecc.size == 1024)
 		*sps >>= 1;
 
-	for (i = 0; i < ARRAY_SIZE(spare); i++) {
-		if (*sps <= spare[i]) {
-			if (!i)
-				*sps = spare[i];
-			else if (*sps != spare[i])
-				*sps = spare[i - 1];
-			break;
+	if (*sps < MTK_NFC_MIN_SPARE)
+		return -EINVAL;
+
+	for (i = 0; i < nfc->caps->num_spare_size; i++) {
+		if (*sps >= spare[i] && spare[i] >= spare[closest_spare]) {
+			closest_spare = i;
+			if (*sps == spare[i])
+				break;
 		}
 	}
 
-	if (i >= ARRAY_SIZE(spare))
-		*sps = spare[ARRAY_SIZE(spare) - 1];
+	*sps = spare[closest_spare];
 
 	if (nand->ecc.size == 1024)
 		*sps <<= 1;
+
+	return 0;
 }
 
 static int mtk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd)
 {
 	struct nand_chip *nand = mtd_to_nand(mtd);
+	struct mtk_nfc *nfc = nand_get_controller_data(nand);
 	u32 spare;
-	int free;
+	int free, ret;
 
 	/* support only ecc hw mode */
 	if (nand->ecc.mode != NAND_ECC_HW) {
@@ -1194,7 +1156,9 @@ static int mtk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd)
 			nand->ecc.size = 1024;
 		}
 
-		mtk_nfc_set_spare_per_sector(&spare, mtd);
+		ret = mtk_nfc_set_spare_per_sector(&spare, mtd);
+		if (ret)
+			return ret;
 
 		/* calculate oob bytes except ecc parity data */
 		free = ((nand->ecc.strength * ECC_PARITY_BITS) + 7) >> 3;
@@ -1214,7 +1178,7 @@ static int mtk_nfc_ecc_init(struct device *dev, struct mtd_info *mtd)
 		}
 	}
 
-	mtk_ecc_adjust_strength(&nand->ecc.strength);
+	mtk_ecc_adjust_strength(nfc->ecc, &nand->ecc.strength);
 
 	dev_info(dev, "eccsize %d eccstrength %d\n",
 		 nand->ecc.size, nand->ecc.strength);
@@ -1312,7 +1276,10 @@ static int mtk_nfc_nand_chip_init(struct device *dev, struct mtk_nfc *nfc,
 		return -EINVAL;
 	}
 
-	mtk_nfc_set_spare_per_sector(&chip->spare_per_sector, mtd);
+	ret = mtk_nfc_set_spare_per_sector(&chip->spare_per_sector, mtd);
+	if (ret)
+		return ret;
+
 	mtk_nfc_set_fdm(&chip->fdm, mtd);
 	mtk_nfc_set_bad_mark_ctl(&chip->bad_mark, mtd);
 
@@ -1354,12 +1321,28 @@ static int mtk_nfc_nand_chips_init(struct device *dev, struct mtk_nfc *nfc)
 	return 0;
 }
 
+static const struct mtk_nfc_caps mtk_nfc_caps_mt2701 = {
+	.spare_size = spare_size_mt2701,
+	.num_spare_size = 16,
+	.pageformat_spare_shift = 4,
+};
+
+static const struct of_device_id mtk_nfc_id_table[] = {
+	{
+		.compatible = "mediatek,mt2701-nfc",
+		.data = &mtk_nfc_caps_mt2701,
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, mtk_nfc_id_table);
+
 static int mtk_nfc_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct device_node *np = dev->of_node;
 	struct mtk_nfc *nfc;
 	struct resource *res;
+	const struct of_device_id *of_nfc_id = NULL;
 	int ret, irq;
 
 	nfc = devm_kzalloc(dev, sizeof(*nfc), GFP_KERNEL);
@@ -1423,6 +1406,14 @@ static int mtk_nfc_probe(struct platform_device *pdev)
 		goto clk_disable;
 	}
 
+	of_nfc_id = of_match_device(mtk_nfc_id_table, &pdev->dev);
+	if (!of_nfc_id) {
+		ret = -ENODEV;
+		goto clk_disable;
+	}
+
+	nfc->caps = of_nfc_id->data;
+
 	platform_set_drvdata(pdev, nfc);
 
 	ret = mtk_nfc_nand_chips_init(dev, nfc);
@@ -1503,12 +1494,6 @@ static int mtk_nfc_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(mtk_nfc_pm_ops, mtk_nfc_suspend, mtk_nfc_resume);
 #endif
 
-static const struct of_device_id mtk_nfc_id_table[] = {
-	{ .compatible = "mediatek,mt2701-nfc" },
-	{}
-};
-MODULE_DEVICE_TABLE(of, mtk_nfc_id_table);
-
 static struct platform_driver mtk_nfc_driver = {
 	.probe  = mtk_nfc_probe,
 	.remove = mtk_nfc_remove,
-- 
1.9.1

[PATCH v5 4/4] mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller

[Xiaolei Li]

MT2712 NAND FLASH Controller is similar to MT2701 except those following:
(1) MT2712 supports up to 148B spare size per 1KB size sector (the same
    with 74B spare size per 512B size sector). There are three new spare
    format: 61, 67, 74.
(2) MT2712 supports up to 80 bit ecc strength. There are three new ecc
    strength level: 68, 72, 80.
(3) MT2712 ECC encode parity data register's start offset is 0x300, and
    different with 0x10 of MT2701.
(4) MT2712 improves ecc irq function. When ECC works in ECC_NFI_MODE,
    MT2701 will generate ecc irq number the same with ecc steps during
    page read. However, MT2712 can only generate one ecc irq.

Changes of this patch are:
(1) add two new variables named pg_irq_sel, encode_parity_reg0 in struct
    mtk_ecc_caps.
(2) add new bitfield ECC_PG_IRQ_SEL for register ECC_IRQ_REG.
(3) add ecc strength array of mt2712.
(4) add spare size array of mt2712.
(5) add mt2712 nfc and ecc device compatiable and data.

Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
---
 drivers/mtd/nand/mtk_ecc.c  | 39 +++++++++++++++++++++++++++++++++++----
 drivers/mtd/nand/mtk_nand.c | 14 ++++++++++++++
 2 files changed, 49 insertions(+), 4 deletions(-)

diff --git a/drivers/mtd/nand/mtk_ecc.c b/drivers/mtd/nand/mtk_ecc.c
index ae51303..4958121 100644
--- a/drivers/mtd/nand/mtk_ecc.c
+++ b/drivers/mtd/nand/mtk_ecc.c
@@ -28,6 +28,7 @@
 
 #define ECC_IDLE_MASK		BIT(0)
 #define ECC_IRQ_EN		BIT(0)
+#define ECC_PG_IRQ_SEL		BIT(1)
 #define ECC_OP_ENABLE		(1)
 #define ECC_OP_DISABLE		(0)
 
@@ -37,7 +38,6 @@
 #define		ECC_MS_SHIFT		(16)
 #define ECC_ENCDIADDR		(0x08)
 #define ECC_ENCIDLE		(0x0C)
-#define ECC_ENCPAR(x)		(0x10 + (x) * sizeof(u32))
 #define ECC_ENCIRQ_EN		(0x80)
 #define ECC_ENCIRQ_STA		(0x84)
 #define ECC_DECCON		(0x100)
@@ -61,6 +61,8 @@ struct mtk_ecc_caps {
 	u32 err_mask;
 	const u8 *ecc_strength;
 	u8 num_ecc_strength;
+	u32 encode_parity_reg0;
+	int pg_irq_sel;
 };
 
 struct mtk_ecc {
@@ -76,12 +78,17 @@ struct mtk_ecc {
 	u8 *eccdata;
 };
 
-/* ecc strength that mt2701 supports */
+/* ecc strength that each IP supports */
 static const u8 ecc_strength_mt2701[] = {
 	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
 	40, 44, 48, 52, 56, 60
 };
 
+static const u8 ecc_strength_mt2712[] = {
+	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+	40, 44, 48, 52, 56, 60, 68, 72, 80
+};
+
 static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc,
 				     enum mtk_ecc_operation op)
 {
@@ -254,6 +261,7 @@ struct mtk_ecc *of_mtk_ecc_get(struct device_node *of_node)
 int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 {
 	enum mtk_ecc_operation op = config->op;
+	u16 reg_val;
 	int ret;
 
 	ret = mutex_lock_interruptible(&ecc->lock);
@@ -271,7 +279,15 @@ int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 	writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op));
 
 	init_completion(&ecc->done);
-	writew(ECC_IRQ_EN, ecc->regs + ECC_IRQ_REG(op));
+	reg_val = ECC_IRQ_EN;
+	/*
+	 * For ECC_NFI_MODE, if ecc->caps->pg_irq_sel is 1, then it
+	 * means this chip can only generate one ecc irq during page
+	 * read / write. If is 0, generate one ecc irq each ecc step.
+	 */
+	if ((ecc->caps->pg_irq_sel) && (config->mode == ECC_NFI_MODE))
+		reg_val |= ECC_PG_IRQ_SEL;
+	writew(reg_val, ecc->regs + ECC_IRQ_REG(op));
 
 	return 0;
 }
@@ -341,7 +357,9 @@ int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config,
 	len = (config->strength * ECC_PARITY_BITS + 7) >> 3;
 
 	/* write the parity bytes generated by the ECC back to temp buffer */
-	__ioread32_copy(ecc->eccdata, ecc->regs + ECC_ENCPAR(0), round_up(len, 4));
+	__ioread32_copy(ecc->eccdata,
+			ecc->regs + ecc->caps->encode_parity_reg0,
+			round_up(len, 4));
 
 	/* copy into possibly unaligned OOB region with actual length */
 	memcpy(data + bytes, ecc->eccdata, len);
@@ -377,12 +395,25 @@ void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p)
 	.err_mask = 0x3f,
 	.ecc_strength = ecc_strength_mt2701,
 	.num_ecc_strength = 20,
+	.encode_parity_reg0 = 0x10,
+	.pg_irq_sel = 0,
+};
+
+static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
+	.err_mask = 0x7f,
+	.ecc_strength = ecc_strength_mt2712,
+	.num_ecc_strength = 23,
+	.encode_parity_reg0 = 0x300,
+	.pg_irq_sel = 1,
 };
 
 static const struct of_device_id mtk_ecc_dt_match[] = {
 	{
 		.compatible = "mediatek,mt2701-ecc",
 		.data = &mtk_ecc_caps_mt2701,
+	}, {
+		.compatible = "mediatek,mt2712-ecc",
+		.data = &mtk_ecc_caps_mt2712,
 	},
 	{},
 };
diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c
index e428669..4d9ee27 100644
--- a/drivers/mtd/nand/mtk_nand.c
+++ b/drivers/mtd/nand/mtk_nand.c
@@ -164,6 +164,11 @@ struct mtk_nfc {
 	16, 26, 27, 28, 32, 36, 40, 44,	48, 49, 50, 51, 52, 62, 63, 64
 };
 
+static const u8 spare_size_mt2712[] = {
+	16, 26, 27, 28, 32, 36, 40, 44, 48, 49, 50, 51, 52, 62, 61, 63, 64, 67,
+	74
+};
+
 static inline struct mtk_nfc_nand_chip *to_mtk_nand(struct nand_chip *nand)
 {
 	return container_of(nand, struct mtk_nfc_nand_chip, nand);
@@ -1327,10 +1332,19 @@ static int mtk_nfc_nand_chips_init(struct device *dev, struct mtk_nfc *nfc)
 	.pageformat_spare_shift = 4,
 };
 
+static const struct mtk_nfc_caps mtk_nfc_caps_mt2712 = {
+	.spare_size = spare_size_mt2712,
+	.num_spare_size = 19,
+	.pageformat_spare_shift = 16,
+};
+
 static const struct of_device_id mtk_nfc_id_table[] = {
 	{
 		.compatible = "mediatek,mt2701-nfc",
 		.data = &mtk_nfc_caps_mt2701,
+	}, {
+		.compatible = "mediatek,mt2712-nfc",
+		.data = &mtk_nfc_caps_mt2712,
 	},
 	{}
 };
-- 
1.9.1

[PATCH v5 4/4] mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller

[Xiaolei Li]

MT2712 NAND FLASH Controller is similar to MT2701 except those following:
(1) MT2712 supports up to 148B spare size per 1KB size sector (the same
    with 74B spare size per 512B size sector). There are three new spare
    format: 61, 67, 74.
(2) MT2712 supports up to 80 bit ecc strength. There are three new ecc
    strength level: 68, 72, 80.
(3) MT2712 ECC encode parity data register's start offset is 0x300, and
    different with 0x10 of MT2701.
(4) MT2712 improves ecc irq function. When ECC works in ECC_NFI_MODE,
    MT2701 will generate ecc irq number the same with ecc steps during
    page read. However, MT2712 can only generate one ecc irq.

Changes of this patch are:
(1) add two new variables named pg_irq_sel, encode_parity_reg0 in struct
    mtk_ecc_caps.
(2) add new bitfield ECC_PG_IRQ_SEL for register ECC_IRQ_REG.
(3) add ecc strength array of mt2712.
(4) add spare size array of mt2712.
(5) add mt2712 nfc and ecc device compatiable and data.

Signed-off-by: Xiaolei Li <xiaolei.li-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
---
 drivers/mtd/nand/mtk_ecc.c  | 39 +++++++++++++++++++++++++++++++++++----
 drivers/mtd/nand/mtk_nand.c | 14 ++++++++++++++
 2 files changed, 49 insertions(+), 4 deletions(-)

diff --git a/drivers/mtd/nand/mtk_ecc.c b/drivers/mtd/nand/mtk_ecc.c
index ae51303..4958121 100644
--- a/drivers/mtd/nand/mtk_ecc.c
+++ b/drivers/mtd/nand/mtk_ecc.c
@@ -28,6 +28,7 @@
 
 #define ECC_IDLE_MASK		BIT(0)
 #define ECC_IRQ_EN		BIT(0)
+#define ECC_PG_IRQ_SEL		BIT(1)
 #define ECC_OP_ENABLE		(1)
 #define ECC_OP_DISABLE		(0)
 
@@ -37,7 +38,6 @@
 #define		ECC_MS_SHIFT		(16)
 #define ECC_ENCDIADDR		(0x08)
 #define ECC_ENCIDLE		(0x0C)
-#define ECC_ENCPAR(x)		(0x10 + (x) * sizeof(u32))
 #define ECC_ENCIRQ_EN		(0x80)
 #define ECC_ENCIRQ_STA		(0x84)
 #define ECC_DECCON		(0x100)
@@ -61,6 +61,8 @@ struct mtk_ecc_caps {
 	u32 err_mask;
 	const u8 *ecc_strength;
 	u8 num_ecc_strength;
+	u32 encode_parity_reg0;
+	int pg_irq_sel;
 };
 
 struct mtk_ecc {
@@ -76,12 +78,17 @@ struct mtk_ecc {
 	u8 *eccdata;
 };
 
-/* ecc strength that mt2701 supports */
+/* ecc strength that each IP supports */
 static const u8 ecc_strength_mt2701[] = {
 	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
 	40, 44, 48, 52, 56, 60
 };
 
+static const u8 ecc_strength_mt2712[] = {
+	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+	40, 44, 48, 52, 56, 60, 68, 72, 80
+};
+
 static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc,
 				     enum mtk_ecc_operation op)
 {
@@ -254,6 +261,7 @@ struct mtk_ecc *of_mtk_ecc_get(struct device_node *of_node)
 int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 {
 	enum mtk_ecc_operation op = config->op;
+	u16 reg_val;
 	int ret;
 
 	ret = mutex_lock_interruptible(&ecc->lock);
@@ -271,7 +279,15 @@ int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 	writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op));
 
 	init_completion(&ecc->done);
-	writew(ECC_IRQ_EN, ecc->regs + ECC_IRQ_REG(op));
+	reg_val = ECC_IRQ_EN;
+	/*
+	 * For ECC_NFI_MODE, if ecc->caps->pg_irq_sel is 1, then it
+	 * means this chip can only generate one ecc irq during page
+	 * read / write. If is 0, generate one ecc irq each ecc step.
+	 */
+	if ((ecc->caps->pg_irq_sel) && (config->mode == ECC_NFI_MODE))
+		reg_val |= ECC_PG_IRQ_SEL;
+	writew(reg_val, ecc->regs + ECC_IRQ_REG(op));
 
 	return 0;
 }
@@ -341,7 +357,9 @@ int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config,
 	len = (config->strength * ECC_PARITY_BITS + 7) >> 3;
 
 	/* write the parity bytes generated by the ECC back to temp buffer */
-	__ioread32_copy(ecc->eccdata, ecc->regs + ECC_ENCPAR(0), round_up(len, 4));
+	__ioread32_copy(ecc->eccdata,
+			ecc->regs + ecc->caps->encode_parity_reg0,
+			round_up(len, 4));
 
 	/* copy into possibly unaligned OOB region with actual length */
 	memcpy(data + bytes, ecc->eccdata, len);
@@ -377,12 +395,25 @@ void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p)
 	.err_mask = 0x3f,
 	.ecc_strength = ecc_strength_mt2701,
 	.num_ecc_strength = 20,
+	.encode_parity_reg0 = 0x10,
+	.pg_irq_sel = 0,
+};
+
+static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
+	.err_mask = 0x7f,
+	.ecc_strength = ecc_strength_mt2712,
+	.num_ecc_strength = 23,
+	.encode_parity_reg0 = 0x300,
+	.pg_irq_sel = 1,
 };
 
 static const struct of_device_id mtk_ecc_dt_match[] = {
 	{
 		.compatible = "mediatek,mt2701-ecc",
 		.data = &mtk_ecc_caps_mt2701,
+	}, {
+		.compatible = "mediatek,mt2712-ecc",
+		.data = &mtk_ecc_caps_mt2712,
 	},
 	{},
 };
diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/mtk_nand.c
index e428669..4d9ee27 100644
--- a/drivers/mtd/nand/mtk_nand.c
+++ b/drivers/mtd/nand/mtk_nand.c
@@ -164,6 +164,11 @@ struct mtk_nfc {
 	16, 26, 27, 28, 32, 36, 40, 44,	48, 49, 50, 51, 52, 62, 63, 64
 };
 
+static const u8 spare_size_mt2712[] = {
+	16, 26, 27, 28, 32, 36, 40, 44, 48, 49, 50, 51, 52, 62, 61, 63, 64, 67,
+	74
+};
+
 static inline struct mtk_nfc_nand_chip *to_mtk_nand(struct nand_chip *nand)
 {
 	return container_of(nand, struct mtk_nfc_nand_chip, nand);
@@ -1327,10 +1332,19 @@ static int mtk_nfc_nand_chips_init(struct device *dev, struct mtk_nfc *nfc)
 	.pageformat_spare_shift = 4,
 };
 
+static const struct mtk_nfc_caps mtk_nfc_caps_mt2712 = {
+	.spare_size = spare_size_mt2712,
+	.num_spare_size = 19,
+	.pageformat_spare_shift = 16,
+};
+
 static const struct of_device_id mtk_nfc_id_table[] = {
 	{
 		.compatible = "mediatek,mt2701-nfc",
 		.data = &mtk_nfc_caps_mt2701,
+	}, {
+		.compatible = "mediatek,mt2712-nfc",
+		.data = &mtk_nfc_caps_mt2712,
 	},
 	{}
 };
-- 
1.9.1

Re: [PATCH v5 0/4] Mediatek MT2712 NAND FLASH Controller driver

[Boris Brezillon]

On Wed, 31 May 2017 16:26:37 +0800
Xiaolei Li <xiaolei.li@mediatek.com> wrote:

> The following patch-set adds support for Mediatek MT2712 NAND FLASH
> Controller.

Applied to nand/next.

Thanks,

Boris

> 
> Changes on v5 relative to:
> --------------------
> 
> tree    : https://github.com/bbrezillon/linux-0day
> branch  : nand/next
> commit  :
>         'commit 2b12c057cc28 ("mtd: nand: brcmnand: Check flash #WP pin
>          status before nand erase/program")'
> 
> Patch v5:
> ---------
> - rename variable j as closest_spare in function mtk_nfc_set_spare_per_sector
> - remove unneeded parenthesis
> - add define MTK_NFC_MIN_SPARE to check whether there is no entry that is
>   less than *sps.
> 
> Patch v4:
> ---------
> - remove spare size array sort. iterate over all entries of spare size
>   table and pick the best one.
> 
> Patch v3:
> ---------
> - separate patches into 4.
> - rename struct mtk_ecc_devdata and struct mtk_nfc_devdata to struct
>   mtk_ecc_caps and struct mtk_nfc_caps respectively.
> - add variables const u8 *ecc_strength and u8 num_ecc_strength into struct
>   mtk_ecc_caps, and remove u8 max_ecc_strength.
> - rename variabl u32 temp in function mtk_ecc_probe to u32 max_eccdata_size.
> - remove ECC_CNFG_xBIT define, use a for loop to do ecc hw configuration.
> - remove const u32 *spare_format from struct mtk_nfc_caps, and add variables
>   u8 num_spare_size and u8 pageformat_spare_shift.
> - remove PAGEFMT_SPARE_ define, use a for loop to do nfc hw configuration.
> - sort spare size array before setting spare size.
> - fix coding style issue.
> 
> Patch v2:
> ---------
> - sperate patches into 3.
> - refine DT bindings documentation about NFC and ECC compatible.
> - use ecc->devdata->encode_parity_reg0 and ecc->devdata->err_mask
>   directly, but hide them in define.
> 
> Tests:
> ------
> 
> * ubifs and jffs2 are validated on NAND device MT29F16G08ADBCA
>   by 'dd' command.
> * all drivers/mtd/tests/* pass.
> * speed test:
>   eraseblock write speed is 8318 KiB/s
>   eraseblock read speed is 11374 KiB/s
>   page write speed is 8155 KiB/s
>   page read speed is 11290 KiB/s
>   2 page write speed is 8217 KiB/s
>   2 page read speed is 11354 KiB/s
>   erase speed is 116472 KiB/s
>   2x multi-block erase speed is 352978 KiB/s
>   4x multi-block erase speed is 359750 KiB/s
>   8x multi-block erase speed is 361484 KiB/s
>   16x multi-block erase speed is 364116 KiB/s
>   32x multi-block erase speed is 364116 KiB/s
>   64x multi-block erase speed is 364116 KiB/s
> 
> Xiaolei Li (4):
>   mtd: nand: mediatek: update DT bindings
>   mtd: nand: mediatek: refine register NFI_PAGEFMT setting
>   mtd: nand: mediatek: add support for different MTK NAND FLASH
>     Controller IP
>   mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller
> 
>  Documentation/devicetree/bindings/mtd/mtk-nand.txt |   5 +-
>  drivers/mtd/nand/mtk_ecc.c                         | 218 ++++++++++-----------
>  drivers/mtd/nand/mtk_ecc.h                         |   2 +-
>  drivers/mtd/nand/mtk_nand.c                        | 187 +++++++++---------
>  4 files changed, 206 insertions(+), 206 deletions(-)
> 
> --
> 1.9.1

Re: [PATCH v5 0/4] Mediatek MT2712 NAND FLASH Controller driver

[Boris Brezillon]

On Wed, 31 May 2017 16:26:37 +0800
Xiaolei Li <xiaolei.li-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org> wrote:

> The following patch-set adds support for Mediatek MT2712 NAND FLASH
> Controller.

Applied to nand/next.

Thanks,

Boris

> 
> Changes on v5 relative to:
> --------------------
> 
> tree    : https://github.com/bbrezillon/linux-0day
> branch  : nand/next
> commit  :
>         'commit 2b12c057cc28 ("mtd: nand: brcmnand: Check flash #WP pin
>          status before nand erase/program")'
> 
> Patch v5:
> ---------
> - rename variable j as closest_spare in function mtk_nfc_set_spare_per_sector
> - remove unneeded parenthesis
> - add define MTK_NFC_MIN_SPARE to check whether there is no entry that is
>   less than *sps.
> 
> Patch v4:
> ---------
> - remove spare size array sort. iterate over all entries of spare size
>   table and pick the best one.
> 
> Patch v3:
> ---------
> - separate patches into 4.
> - rename struct mtk_ecc_devdata and struct mtk_nfc_devdata to struct
>   mtk_ecc_caps and struct mtk_nfc_caps respectively.
> - add variables const u8 *ecc_strength and u8 num_ecc_strength into struct
>   mtk_ecc_caps, and remove u8 max_ecc_strength.
> - rename variabl u32 temp in function mtk_ecc_probe to u32 max_eccdata_size.
> - remove ECC_CNFG_xBIT define, use a for loop to do ecc hw configuration.
> - remove const u32 *spare_format from struct mtk_nfc_caps, and add variables
>   u8 num_spare_size and u8 pageformat_spare_shift.
> - remove PAGEFMT_SPARE_ define, use a for loop to do nfc hw configuration.
> - sort spare size array before setting spare size.
> - fix coding style issue.
> 
> Patch v2:
> ---------
> - sperate patches into 3.
> - refine DT bindings documentation about NFC and ECC compatible.
> - use ecc->devdata->encode_parity_reg0 and ecc->devdata->err_mask
>   directly, but hide them in define.
> 
> Tests:
> ------
> 
> * ubifs and jffs2 are validated on NAND device MT29F16G08ADBCA
>   by 'dd' command.
> * all drivers/mtd/tests/* pass.
> * speed test:
>   eraseblock write speed is 8318 KiB/s
>   eraseblock read speed is 11374 KiB/s
>   page write speed is 8155 KiB/s
>   page read speed is 11290 KiB/s
>   2 page write speed is 8217 KiB/s
>   2 page read speed is 11354 KiB/s
>   erase speed is 116472 KiB/s
>   2x multi-block erase speed is 352978 KiB/s
>   4x multi-block erase speed is 359750 KiB/s
>   8x multi-block erase speed is 361484 KiB/s
>   16x multi-block erase speed is 364116 KiB/s
>   32x multi-block erase speed is 364116 KiB/s
>   64x multi-block erase speed is 364116 KiB/s
> 
> Xiaolei Li (4):
>   mtd: nand: mediatek: update DT bindings
>   mtd: nand: mediatek: refine register NFI_PAGEFMT setting
>   mtd: nand: mediatek: add support for different MTK NAND FLASH
>     Controller IP
>   mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller
> 
>  Documentation/devicetree/bindings/mtd/mtk-nand.txt |   5 +-
>  drivers/mtd/nand/mtk_ecc.c                         | 218 ++++++++++-----------
>  drivers/mtd/nand/mtk_ecc.h                         |   2 +-
>  drivers/mtd/nand/mtk_nand.c                        | 187 +++++++++---------
>  4 files changed, 206 insertions(+), 206 deletions(-)
> 
> --
> 1.9.1

Re: [PATCH v5 0/4] Mediatek MT2712 NAND FLASH Controller driver

[xiaolei li]

On Wed, 2017-05-31 at 16:32 +0200, Boris Brezillon wrote:
> On Wed, 31 May 2017 16:26:37 +0800
> Xiaolei Li <xiaolei.li@mediatek.com> wrote:
> 
> > The following patch-set adds support for Mediatek MT2712 NAND FLASH
> > Controller.
> 
> Applied to nand/next.
> 
> Thanks,
> 
> Boris
> 

Thanks very much for all the reviews.

Thanks,
Xiaolei

> > 
> > Changes on v5 relative to:
> > --------------------
> > 
> > tree    : https://github.com/bbrezillon/linux-0day
> > branch  : nand/next
> > commit  :
> >         'commit 2b12c057cc28 ("mtd: nand: brcmnand: Check flash #WP pin
> >          status before nand erase/program")'
> > 
> > Patch v5:
> > ---------
> > - rename variable j as closest_spare in function mtk_nfc_set_spare_per_sector
> > - remove unneeded parenthesis
> > - add define MTK_NFC_MIN_SPARE to check whether there is no entry that is
> >   less than *sps.
> > 
> > Patch v4:
> > ---------
> > - remove spare size array sort. iterate over all entries of spare size
> >   table and pick the best one.
> > 
> > Patch v3:
> > ---------
> > - separate patches into 4.
> > - rename struct mtk_ecc_devdata and struct mtk_nfc_devdata to struct
> >   mtk_ecc_caps and struct mtk_nfc_caps respectively.
> > - add variables const u8 *ecc_strength and u8 num_ecc_strength into struct
> >   mtk_ecc_caps, and remove u8 max_ecc_strength.
> > - rename variabl u32 temp in function mtk_ecc_probe to u32 max_eccdata_size.
> > - remove ECC_CNFG_xBIT define, use a for loop to do ecc hw configuration.
> > - remove const u32 *spare_format from struct mtk_nfc_caps, and add variables
> >   u8 num_spare_size and u8 pageformat_spare_shift.
> > - remove PAGEFMT_SPARE_ define, use a for loop to do nfc hw configuration.
> > - sort spare size array before setting spare size.
> > - fix coding style issue.
> > 
> > Patch v2:
> > ---------
> > - sperate patches into 3.
> > - refine DT bindings documentation about NFC and ECC compatible.
> > - use ecc->devdata->encode_parity_reg0 and ecc->devdata->err_mask
> >   directly, but hide them in define.
> > 
> > Tests:
> > ------
> > 
> > * ubifs and jffs2 are validated on NAND device MT29F16G08ADBCA
> >   by 'dd' command.
> > * all drivers/mtd/tests/* pass.
> > * speed test:
> >   eraseblock write speed is 8318 KiB/s
> >   eraseblock read speed is 11374 KiB/s
> >   page write speed is 8155 KiB/s
> >   page read speed is 11290 KiB/s
> >   2 page write speed is 8217 KiB/s
> >   2 page read speed is 11354 KiB/s
> >   erase speed is 116472 KiB/s
> >   2x multi-block erase speed is 352978 KiB/s
> >   4x multi-block erase speed is 359750 KiB/s
> >   8x multi-block erase speed is 361484 KiB/s
> >   16x multi-block erase speed is 364116 KiB/s
> >   32x multi-block erase speed is 364116 KiB/s
> >   64x multi-block erase speed is 364116 KiB/s
> > 
> > Xiaolei Li (4):
> >   mtd: nand: mediatek: update DT bindings
> >   mtd: nand: mediatek: refine register NFI_PAGEFMT setting
> >   mtd: nand: mediatek: add support for different MTK NAND FLASH
> >     Controller IP
> >   mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller
> > 
> >  Documentation/devicetree/bindings/mtd/mtk-nand.txt |   5 +-
> >  drivers/mtd/nand/mtk_ecc.c                         | 218 ++++++++++-----------
> >  drivers/mtd/nand/mtk_ecc.h                         |   2 +-
> >  drivers/mtd/nand/mtk_nand.c                        | 187 +++++++++---------
> >  4 files changed, 206 insertions(+), 206 deletions(-)
> > 
> > --
> > 1.9.1
> 

Re: [PATCH v5 0/4] Mediatek MT2712 NAND FLASH Controller driver

[xiaolei li]

On Wed, 2017-05-31 at 16:32 +0200, Boris Brezillon wrote:
> On Wed, 31 May 2017 16:26:37 +0800
> Xiaolei Li <xiaolei.li@mediatek.com> wrote:
> 
> > The following patch-set adds support for Mediatek MT2712 NAND FLASH
> > Controller.
> 
> Applied to nand/next.
> 
> Thanks,
> 
> Boris
> 

Thanks very much for all the reviews.

Thanks,
Xiaolei

> > 
> > Changes on v5 relative to:
> > --------------------
> > 
> > tree    : https://github.com/bbrezillon/linux-0day
> > branch  : nand/next
> > commit  :
> >         'commit 2b12c057cc28 ("mtd: nand: brcmnand: Check flash #WP pin
> >          status before nand erase/program")'
> > 
> > Patch v5:
> > ---------
> > - rename variable j as closest_spare in function mtk_nfc_set_spare_per_sector
> > - remove unneeded parenthesis
> > - add define MTK_NFC_MIN_SPARE to check whether there is no entry that is
> >   less than *sps.
> > 
> > Patch v4:
> > ---------
> > - remove spare size array sort. iterate over all entries of spare size
> >   table and pick the best one.
> > 
> > Patch v3:
> > ---------
> > - separate patches into 4.
> > - rename struct mtk_ecc_devdata and struct mtk_nfc_devdata to struct
> >   mtk_ecc_caps and struct mtk_nfc_caps respectively.
> > - add variables const u8 *ecc_strength and u8 num_ecc_strength into struct
> >   mtk_ecc_caps, and remove u8 max_ecc_strength.
> > - rename variabl u32 temp in function mtk_ecc_probe to u32 max_eccdata_size.
> > - remove ECC_CNFG_xBIT define, use a for loop to do ecc hw configuration.
> > - remove const u32 *spare_format from struct mtk_nfc_caps, and add variables
> >   u8 num_spare_size and u8 pageformat_spare_shift.
> > - remove PAGEFMT_SPARE_ define, use a for loop to do nfc hw configuration.
> > - sort spare size array before setting spare size.
> > - fix coding style issue.
> > 
> > Patch v2:
> > ---------
> > - sperate patches into 3.
> > - refine DT bindings documentation about NFC and ECC compatible.
> > - use ecc->devdata->encode_parity_reg0 and ecc->devdata->err_mask
> >   directly, but hide them in define.
> > 
> > Tests:
> > ------
> > 
> > * ubifs and jffs2 are validated on NAND device MT29F16G08ADBCA
> >   by 'dd' command.
> > * all drivers/mtd/tests/* pass.
> > * speed test:
> >   eraseblock write speed is 8318 KiB/s
> >   eraseblock read speed is 11374 KiB/s
> >   page write speed is 8155 KiB/s
> >   page read speed is 11290 KiB/s
> >   2 page write speed is 8217 KiB/s
> >   2 page read speed is 11354 KiB/s
> >   erase speed is 116472 KiB/s
> >   2x multi-block erase speed is 352978 KiB/s
> >   4x multi-block erase speed is 359750 KiB/s
> >   8x multi-block erase speed is 361484 KiB/s
> >   16x multi-block erase speed is 364116 KiB/s
> >   32x multi-block erase speed is 364116 KiB/s
> >   64x multi-block erase speed is 364116 KiB/s
> > 
> > Xiaolei Li (4):
> >   mtd: nand: mediatek: update DT bindings
> >   mtd: nand: mediatek: refine register NFI_PAGEFMT setting
> >   mtd: nand: mediatek: add support for different MTK NAND FLASH
> >     Controller IP
> >   mtd: nand: mediatek: add support for MT2712 NAND FLASH Controller
> > 
> >  Documentation/devicetree/bindings/mtd/mtk-nand.txt |   5 +-
> >  drivers/mtd/nand/mtk_ecc.c                         | 218 ++++++++++-----------
> >  drivers/mtd/nand/mtk_ecc.h                         |   2 +-
> >  drivers/mtd/nand/mtk_nand.c                        | 187 +++++++++---------
> >  4 files changed, 206 insertions(+), 206 deletions(-)
> > 
> > --
> > 1.9.1
> 



______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/