* [U-Boot] [PATCH v2] sun50i: h5: Add initial Orangepi Prime support
@ 2017-06-01 15:25 Jagan Teki
2017-06-02 13:23 ` Maxime Ripard
2017-06-02 14:31 ` [U-Boot] [linux-sunxi] " icenowy at aosc.io
0 siblings, 2 replies; 5+ messages in thread
From: Jagan Teki @ 2017-06-01 15:25 UTC (permalink / raw)
To: u-boot
From: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT
Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology
CPU: Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet at 1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v2:
- Drop http link from commit message
- Drop CONFIG_CONSOLE_MUX
arch/arm/dts/Makefile | 3 +-
arch/arm/dts/sun50i-h5-orangepi-prime.dts | 104 ++++++++++++++++++++++++++++++
board/sunxi/MAINTAINERS | 5 ++
configs/orangepi_prime_defconfig | 16 +++++
4 files changed, 127 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/dts/sun50i-h5-orangepi-prime.dts
create mode 100644 configs/orangepi_prime_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 82671b3..b8ebd6e 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -315,7 +315,8 @@ dtb-$(CONFIG_MACH_SUN8I_R40) += \
dtb-$(CONFIG_MACH_SUN8I_V3S) += \
sun8i-v3s-licheepi-zero.dtb
dtb-$(CONFIG_MACH_SUN50I_H5) += \
- sun50i-h5-orangepi-pc2.dtb
+ sun50i-h5-orangepi-pc2.dtb \
+ sun50i-h5-orangepi-prime.dtb
dtb-$(CONFIG_MACH_SUN50I) += \
sun50i-a64-bananapi-m64.dtb \
sun50i-a64-pine64-plus.dtb \
diff --git a/arch/arm/dts/sun50i-h5-orangepi-prime.dts b/arch/arm/dts/sun50i-h5-orangepi-prime.dts
new file mode 100644
index 0000000..67eade7
--- /dev/null
+++ b/arch/arm/dts/sun50i-h5-orangepi-prime.dts
@@ -0,0 +1,104 @@
+/*
+ * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "OrangePi Prime";
+ compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x40000000 0x80000000>;
+ };
+
+ soc {
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+};
+
+&mmc0 {
+ compatible = "allwinner,sun50i-h5-mmc",
+ "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 5b51420..0f1290a 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -272,6 +272,11 @@ M: Andre Przywara <andre.przywara@arm.com>
S: Maintained
F: configs/orangepi_pc2_defconfig
+ORANGEPI PRIME BOARD
+M: Jagan Teki <jagan@amarulasolutions.com>
+S: Maintained
+F: configs/orangepi_prime_defconfig
+
PINE64 BOARDS
M: Andre Przywara <andre.przywara@arm.com>
S: Maintained
diff --git a/configs/orangepi_prime_defconfig b/configs/orangepi_prime_defconfig
new file mode 100644
index 0000000..dc8d59e
--- /dev/null
+++ b/configs/orangepi_prime_defconfig
@@ -0,0 +1,16 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN50I_H5=y
+CONFIG_DRAM_CLK=672
+CONFIG_DRAM_ZQ=3881977
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-orangepi-prime"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_ISO_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
--
1.9.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH v2] sun50i: h5: Add initial Orangepi Prime support
2017-06-01 15:25 [U-Boot] [PATCH v2] sun50i: h5: Add initial Orangepi Prime support Jagan Teki
@ 2017-06-02 13:23 ` Maxime Ripard
2017-06-02 18:01 ` Jagan Teki
2017-06-02 14:31 ` [U-Boot] [linux-sunxi] " icenowy at aosc.io
1 sibling, 1 reply; 5+ messages in thread
From: Maxime Ripard @ 2017-06-02 13:23 UTC (permalink / raw)
To: u-boot
On Thu, Jun 01, 2017 at 03:25:32PM +0000, Jagan Teki wrote:
> From: Jagan Teki <jagan@amarulasolutions.com>
>
> Orangepi Prime is an open-source single-board computer
> using the Allwinner h5 SOC.
>
> H5 Orangepi Prime has
> - Quad-core Cortex-A53
> - 2GB DDR3
> - Debug TTL UART
> - 1000M/100M Ethernet RJ45
> - Three USB 2.0
> - HDMI
> - Audio and MIC
> - Wifi + BT
> - IR receiver
> - HDMI
> - Wifi + BT
>
> Boot from MMC:
> -------------
> U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
> DRAM: 2048 MiB
> Trying to boot from MMC1
> NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
> NOTICE: Configuring SPC Controller
> NOTICE: BL3-1: v1.0(debug):aa75c8d
> NOTICE: BL3-1: Built : 18:28:27, May 24 2017
> INFO: BL3-1: Initializing runtime services
> INFO: BL3-1: Preparing for EL3 exit to normal world
> INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
>
> U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology
>
> CPU: Allwinner H5 (SUN50I)
> Model: OrangePi Prime
> DRAM: 2 GiB
> MMC: SUNXI SD/MMC: 0
> *** Warning - bad CRC, using default environment
>
> In: serial
> Out: serial
> Err: serial
> Net: phy interface7
> eth0: ethernet at 1c30000
> starting USB...
> USB0: USB EHCI 1.00
> USB1: USB OHCI 1.0
> scanning bus 0 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 0 Storage Device(s) found
> Hit any key to stop autoboot: 0
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170602/36d9cdb4/attachment.sig>
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] [linux-sunxi] [PATCH v2] sun50i: h5: Add initial Orangepi Prime support
2017-06-01 15:25 [U-Boot] [PATCH v2] sun50i: h5: Add initial Orangepi Prime support Jagan Teki
2017-06-02 13:23 ` Maxime Ripard
@ 2017-06-02 14:31 ` icenowy at aosc.io
2017-06-02 14:49 ` Maxime Ripard
1 sibling, 1 reply; 5+ messages in thread
From: icenowy at aosc.io @ 2017-06-02 14:31 UTC (permalink / raw)
To: u-boot
在 2017-06-01 23:25,Jagan Teki 写道:
> From: Jagan Teki <jagan@amarulasolutions.com>
>
> Orangepi Prime is an open-source single-board computer
> using the Allwinner h5 SOC.
>
> H5 Orangepi Prime has
> - Quad-core Cortex-A53
> - 2GB DDR3
> - Debug TTL UART
> - 1000M/100M Ethernet RJ45
> - Three USB 2.0
> - HDMI
> - Audio and MIC
> - Wifi + BT
> - IR receiver
> - HDMI
> - Wifi + BT
>
> Boot from MMC:
> -------------
> U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
> DRAM: 2048 MiB
> Trying to boot from MMC1
> NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
> NOTICE: Configuring SPC Controller
> NOTICE: BL3-1: v1.0(debug):aa75c8d
> NOTICE: BL3-1: Built : 18:28:27, May 24 2017
> INFO: BL3-1: Initializing runtime services
> INFO: BL3-1: Preparing for EL3 exit to normal world
> INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
>
> U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000)
> Allwinner Technology
>
> CPU: Allwinner H5 (SUN50I)
> Model: OrangePi Prime
> DRAM: 2 GiB
> MMC: SUNXI SD/MMC: 0
> *** Warning - bad CRC, using default environment
>
> In: serial
> Out: serial
> Err: serial
> Net: phy interface7
> eth0: ethernet at 1c30000
> starting USB...
> USB0: USB EHCI 1.00
> USB1: USB OHCI 1.0
> scanning bus 0 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 0 Storage Device(s) found
> Hit any key to stop autoboot: 0
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> Changes for v2:
> - Drop http link from commit message
> - Drop CONFIG_CONSOLE_MUX
Why drop this?
I think now vidconsole is working on H5...
>
> arch/arm/dts/Makefile | 3 +-
> arch/arm/dts/sun50i-h5-orangepi-prime.dts | 104
> ++++++++++++++++++++++++++++++
> board/sunxi/MAINTAINERS | 5 ++
> configs/orangepi_prime_defconfig | 16 +++++
> 4 files changed, 127 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/dts/sun50i-h5-orangepi-prime.dts
> create mode 100644 configs/orangepi_prime_defconfig
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 82671b3..b8ebd6e 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -315,7 +315,8 @@ dtb-$(CONFIG_MACH_SUN8I_R40) += \
> dtb-$(CONFIG_MACH_SUN8I_V3S) += \
> sun8i-v3s-licheepi-zero.dtb
> dtb-$(CONFIG_MACH_SUN50I_H5) += \
> - sun50i-h5-orangepi-pc2.dtb
> + sun50i-h5-orangepi-pc2.dtb \
> + sun50i-h5-orangepi-prime.dtb
> dtb-$(CONFIG_MACH_SUN50I) += \
> sun50i-a64-bananapi-m64.dtb \
> sun50i-a64-pine64-plus.dtb \
> diff --git a/arch/arm/dts/sun50i-h5-orangepi-prime.dts
> b/arch/arm/dts/sun50i-h5-orangepi-prime.dts
> new file mode 100644
> index 0000000..67eade7
> --- /dev/null
> +++ b/arch/arm/dts/sun50i-h5-orangepi-prime.dts
> @@ -0,0 +1,104 @@
> +/*
> + * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This library is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> the
> + * License, or (at your option) any later version.
> + *
> + * This library is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h5.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "OrangePi Prime";
> + compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory {
> + reg = <0x40000000 0x80000000>;
> + };
> +
> + soc {
> + reg_vcc3v3: vcc3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> + };
> +};
> +
> +&mmc0 {
> + compatible = "allwinner,sun50i-h5-mmc",
> + "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
> + cd-inverted;
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins_a>;
> + status = "okay";
> +};
> +
> +&usbphy {
> + status = "okay";
> +};
> +
> +&ohci1 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
> index 5b51420..0f1290a 100644
> --- a/board/sunxi/MAINTAINERS
> +++ b/board/sunxi/MAINTAINERS
> @@ -272,6 +272,11 @@ M: Andre Przywara <andre.przywara@arm.com>
> S: Maintained
> F: configs/orangepi_pc2_defconfig
>
> +ORANGEPI PRIME BOARD
> +M: Jagan Teki <jagan@amarulasolutions.com>
> +S: Maintained
> +F: configs/orangepi_prime_defconfig
> +
> PINE64 BOARDS
> M: Andre Przywara <andre.przywara@arm.com>
> S: Maintained
> diff --git a/configs/orangepi_prime_defconfig
> b/configs/orangepi_prime_defconfig
> new file mode 100644
> index 0000000..dc8d59e
> --- /dev/null
> +++ b/configs/orangepi_prime_defconfig
> @@ -0,0 +1,16 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_SUNXI=y
> +CONFIG_MACH_SUN50I_H5=y
> +CONFIG_DRAM_CLK=672
> +CONFIG_DRAM_ZQ=3881977
> +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-orangepi-prime"
> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> +CONFIG_SPL=y
> +# CONFIG_CMD_IMLS is not set
> +# CONFIG_CMD_FLASH is not set
> +# CONFIG_CMD_FPGA is not set
> +# CONFIG_SPL_DOS_PARTITION is not set
> +# CONFIG_SPL_ISO_PARTITION is not set
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_SUN8I_EMAC=y
> +CONFIG_USB_EHCI_HCD=y
> --
> 1.9.1
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] [linux-sunxi] [PATCH v2] sun50i: h5: Add initial Orangepi Prime support
2017-06-02 14:31 ` [U-Boot] [linux-sunxi] " icenowy at aosc.io
@ 2017-06-02 14:49 ` Maxime Ripard
0 siblings, 0 replies; 5+ messages in thread
From: Maxime Ripard @ 2017-06-02 14:49 UTC (permalink / raw)
To: u-boot
On Fri, Jun 02, 2017 at 10:31:48PM +0800, icenowy at aosc.io wrote:
> 在 2017-06-01 23:25,Jagan Teki 写道:
> > From: Jagan Teki <jagan@amarulasolutions.com>
> >
> > Orangepi Prime is an open-source single-board computer
> > using the Allwinner h5 SOC.
> >
> > H5 Orangepi Prime has
> > - Quad-core Cortex-A53
> > - 2GB DDR3
> > - Debug TTL UART
> > - 1000M/100M Ethernet RJ45
> > - Three USB 2.0
> > - HDMI
> > - Audio and MIC
> > - Wifi + BT
> > - IR receiver
> > - HDMI
> > - Wifi + BT
> >
> > Boot from MMC:
> > -------------
> > U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
> > DRAM: 2048 MiB
> > Trying to boot from MMC1
> > NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
> > NOTICE: Configuring SPC Controller
> > NOTICE: BL3-1: v1.0(debug):aa75c8d
> > NOTICE: BL3-1: Built : 18:28:27, May 24 2017
> > INFO: BL3-1: Initializing runtime services
> > INFO: BL3-1: Preparing for EL3 exit to normal world
> > INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
> >
> > U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000)
> > Allwinner Technology
> >
> > CPU: Allwinner H5 (SUN50I)
> > Model: OrangePi Prime
> > DRAM: 2 GiB
> > MMC: SUNXI SD/MMC: 0
> > *** Warning - bad CRC, using default environment
> >
> > In: serial
> > Out: serial
> > Err: serial
> > Net: phy interface7
> > eth0: ethernet at 1c30000
> > starting USB...
> > USB0: USB EHCI 1.00
> > USB1: USB OHCI 1.0
> > scanning bus 0 for devices... 1 USB Device(s) found
> > scanning usb for storage devices... 0 Storage Device(s) found
> > Hit any key to stop autoboot: 0
> >
> > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> > ---
> > Changes for v2:
> > - Drop http link from commit message
> > - Drop CONFIG_CONSOLE_MUX
>
> Why drop this?
>
> I think now vidconsole is working on H5...
Because it doesn't make any sense to have it in only one or a fraction
of the boards we support.
This is something the user should choose, and opt in.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170602/c3c73614/attachment.sig>
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot] [PATCH v2] sun50i: h5: Add initial Orangepi Prime support
2017-06-02 13:23 ` Maxime Ripard
@ 2017-06-02 18:01 ` Jagan Teki
0 siblings, 0 replies; 5+ messages in thread
From: Jagan Teki @ 2017-06-02 18:01 UTC (permalink / raw)
To: u-boot
On Fri, Jun 2, 2017 at 6:53 PM, Maxime Ripard
<maxime.ripard@free-electrons.com> wrote:
> On Thu, Jun 01, 2017 at 03:25:32PM +0000, Jagan Teki wrote:
>> From: Jagan Teki <jagan@amarulasolutions.com>
>>
>> Orangepi Prime is an open-source single-board computer
>> using the Allwinner h5 SOC.
>>
>> H5 Orangepi Prime has
>> - Quad-core Cortex-A53
>> - 2GB DDR3
>> - Debug TTL UART
>> - 1000M/100M Ethernet RJ45
>> - Three USB 2.0
>> - HDMI
>> - Audio and MIC
>> - Wifi + BT
>> - IR receiver
>> - HDMI
>> - Wifi + BT
>>
>> Boot from MMC:
>> -------------
>> U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
>> DRAM: 2048 MiB
>> Trying to boot from MMC1
>> NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
>> NOTICE: Configuring SPC Controller
>> NOTICE: BL3-1: v1.0(debug):aa75c8d
>> NOTICE: BL3-1: Built : 18:28:27, May 24 2017
>> INFO: BL3-1: Initializing runtime services
>> INFO: BL3-1: Preparing for EL3 exit to normal world
>> INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
>>
>> U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology
>>
>> CPU: Allwinner H5 (SUN50I)
>> Model: OrangePi Prime
>> DRAM: 2 GiB
>> MMC: SUNXI SD/MMC: 0
>> *** Warning - bad CRC, using default environment
>>
>> In: serial
>> Out: serial
>> Err: serial
>> Net: phy interface7
>> eth0: ethernet at 1c30000
>> starting USB...
>> USB0: USB EHCI 1.00
>> USB1: USB OHCI 1.0
>> scanning bus 0 for devices... 1 USB Device(s) found
>> scanning usb for storage devices... 0 Storage Device(s) found
>> Hit any key to stop autoboot: 0
>>
>> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
>
> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Applied to u-boot-sunxi/master
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2017-06-02 18:01 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-06-01 15:25 [U-Boot] [PATCH v2] sun50i: h5: Add initial Orangepi Prime support Jagan Teki
2017-06-02 13:23 ` Maxime Ripard
2017-06-02 18:01 ` Jagan Teki
2017-06-02 14:31 ` [U-Boot] [linux-sunxi] " icenowy at aosc.io
2017-06-02 14:49 ` Maxime Ripard
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.