[PATCH v4 0/2] add thermal nodes for UniPhier SoCs

[PATCH v4 0/2] add thermal nodes for UniPhier SoCs

[Kunihiko Hayashi]

This series adds thermal nodes for UniPhier PXs2 and LD20 SoCs.

Changes since v3:
- rebase on top of linux-next

Changes since v2:
- add the calibration value to device tree for LD20 reference board

Changes since v1:
- separate from driver's patchset[1]
- add cooling-maps nodes on the device tree
- fix an interrupt trigger to set 'level-triggered' according to
  hardware specification
- bring up threshold temperature for LD20 according to the spec sheet
- add cpuN labels for reference in cooling-device property on PXs2 dts

[1] https://lkml.org/lkml/2017/6/28/170

Kunihiko Hayashi (2):
  ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for
    PXs2
  arm64: dts: uniphier: add nodes of thermal monitor and thermal zone
    for LD20

 arch/arm/boot/dts/uniphier-pxs2.dtsi               | 43 ++++++++++++++++++++--
 .../arm64/boot/dts/socionext/uniphier-ld20-ref.dts |  4 ++
 arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi   | 40 ++++++++++++++++++++
 3 files changed, 83 insertions(+), 4 deletions(-)

-- 
2.7.4

[PATCH v4 0/2] add thermal nodes for UniPhier SoCs

[Kunihiko Hayashi]

This series adds thermal nodes for UniPhier PXs2 and LD20 SoCs.

Changes since v3:
- rebase on top of linux-next

Changes since v2:
- add the calibration value to device tree for LD20 reference board

Changes since v1:
- separate from driver's patchset[1]
- add cooling-maps nodes on the device tree
- fix an interrupt trigger to set 'level-triggered' according to
  hardware specification
- bring up threshold temperature for LD20 according to the spec sheet
- add cpuN labels for reference in cooling-device property on PXs2 dts

[1] https://lkml.org/lkml/2017/6/28/170

Kunihiko Hayashi (2):
  ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for
    PXs2
  arm64: dts: uniphier: add nodes of thermal monitor and thermal zone
    for LD20

 arch/arm/boot/dts/uniphier-pxs2.dtsi               | 43 ++++++++++++++++++++--
 .../arm64/boot/dts/socionext/uniphier-ld20-ref.dts |  4 ++
 arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi   | 40 ++++++++++++++++++++
 3 files changed, 83 insertions(+), 4 deletions(-)

-- 
2.7.4

[PATCH v4 1/2] ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for PXs2

[Kunihiko Hayashi]

Add nodes of thermal monitor and thermal zone for UniPhier PXs2 SoC.
The thermal monitor is included in sysctrl.
Furthermore, add cpuN labels for reference in cooling-device property.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 arch/arm/boot/dts/uniphier-pxs2.dtsi | 43 ++++++++++++++++++++++++++++++++----
 1 file changed, 39 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/uniphier-pxs2.dtsi b/arch/arm/boot/dts/uniphier-pxs2.dtsi
index 90b020c..c89e0d5 100644
--- a/arch/arm/boot/dts/uniphier-pxs2.dtsi
+++ b/arch/arm/boot/dts/uniphier-pxs2.dtsi
@@ -16,7 +16,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <0>;
@@ -24,9 +24,10 @@
 			enable-method = "psci";
 			next-level-cache = <&l2>;
 			operating-points-v2 = <&cpu_opp>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <1>;
@@ -36,7 +37,7 @@
 			operating-points-v2 = <&cpu_opp>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <2>;
@@ -46,7 +47,7 @@
 			operating-points-v2 = <&cpu_opp>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <3>;
@@ -114,6 +115,34 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal {
+			polling-delay-passive = <250>;	/* 250ms */
+			polling-delay = <1000>;		/* 1000ms */
+			thermal-sensors = <&pvtctl>;
+
+			trips {
+				cpu_crit: cpu_crit {
+					temperature = <95000>;	/* 95C */
+					hysteresis = <2000>;
+					type = "critical";
+				};
+				cpu_alert: cpu_alert {
+					temperature = <85000>;	/* 85C */
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map {
+					trip = <&cpu_alert>;
+					cooling-device = <&cpu0 (-1) (-1)>;
+				};
+			};
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -358,6 +387,12 @@
 				compatible = "socionext,uniphier-pxs2-reset";
 				#reset-cells = <1>;
 			};
+
+			pvtctl: pvtctl {
+				compatible = "socionext,uniphier-pxs2-thermal";
+				interrupts = <0 3 4>;
+				#thermal-sensor-cells = <0>;
+			};
 		};
 
 		nand: nand@68000000 {
-- 
2.7.4

[PATCH v4 1/2] ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for PXs2

[Kunihiko Hayashi]

Add nodes of thermal monitor and thermal zone for UniPhier PXs2 SoC.
The thermal monitor is included in sysctrl.
Furthermore, add cpuN labels for reference in cooling-device property.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 arch/arm/boot/dts/uniphier-pxs2.dtsi | 43 ++++++++++++++++++++++++++++++++----
 1 file changed, 39 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/uniphier-pxs2.dtsi b/arch/arm/boot/dts/uniphier-pxs2.dtsi
index 90b020c..c89e0d5 100644
--- a/arch/arm/boot/dts/uniphier-pxs2.dtsi
+++ b/arch/arm/boot/dts/uniphier-pxs2.dtsi
@@ -16,7 +16,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu at 0 {
+		cpu0: cpu at 0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <0>;
@@ -24,9 +24,10 @@
 			enable-method = "psci";
 			next-level-cache = <&l2>;
 			operating-points-v2 = <&cpu_opp>;
+			#cooling-cells = <2>;
 		};
 
-		cpu at 1 {
+		cpu1: cpu at 1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <1>;
@@ -36,7 +37,7 @@
 			operating-points-v2 = <&cpu_opp>;
 		};
 
-		cpu at 2 {
+		cpu2: cpu at 2 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <2>;
@@ -46,7 +47,7 @@
 			operating-points-v2 = <&cpu_opp>;
 		};
 
-		cpu at 3 {
+		cpu3: cpu at 3 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <3>;
@@ -114,6 +115,34 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal {
+			polling-delay-passive = <250>;	/* 250ms */
+			polling-delay = <1000>;		/* 1000ms */
+			thermal-sensors = <&pvtctl>;
+
+			trips {
+				cpu_crit: cpu_crit {
+					temperature = <95000>;	/* 95C */
+					hysteresis = <2000>;
+					type = "critical";
+				};
+				cpu_alert: cpu_alert {
+					temperature = <85000>;	/* 85C */
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map {
+					trip = <&cpu_alert>;
+					cooling-device = <&cpu0 (-1) (-1)>;
+				};
+			};
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -358,6 +387,12 @@
 				compatible = "socionext,uniphier-pxs2-reset";
 				#reset-cells = <1>;
 			};
+
+			pvtctl: pvtctl {
+				compatible = "socionext,uniphier-pxs2-thermal";
+				interrupts = <0 3 4>;
+				#thermal-sensor-cells = <0>;
+			};
 		};
 
 		nand: nand at 68000000 {
-- 
2.7.4

[PATCH v4 2/2] arm64: dts: uniphier: add nodes of thermal monitor and thermal zone for LD20

[Kunihiko Hayashi]

Add nodes of thermal monitor and thermal zone for UniPhier LD20 SoC.
The thermal monitor is included in sysctrl.

Furthermore, since the reference board doesn't have a calibrated value of
thermal monitor, this patch gives the default value for LD20 reference
board.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 .../arm64/boot/dts/socionext/uniphier-ld20-ref.dts |  4 +++
 arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi   | 40 ++++++++++++++++++++++
 2 files changed, 44 insertions(+)

diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
index 1ca0c86..5bb63a2 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
@@ -50,3 +50,7 @@
 &i2c0 {
 	status = "okay";
 };
+
+&pvtctl {
+	socionext,tmod-calibration = <0x0f22 0x68ee>;
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
index a29c279..0f733ad 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
@@ -46,6 +46,7 @@
 			clocks = <&sys_clk 32>;
 			enable-method = "psci";
 			operating-points-v2 = <&cluster0_opp>;
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu@1 {
@@ -64,6 +65,7 @@
 			clocks = <&sys_clk 33>;
 			enable-method = "psci";
 			operating-points-v2 = <&cluster1_opp>;
+			#cooling-cells = <2>;
 		};
 
 		cpu3: cpu@101 {
@@ -173,6 +175,38 @@
 			     <1 10 4>;
 	};
 
+	thermal-zones {
+		cpu_thermal {
+			polling-delay-passive = <250>;	/* 250ms */
+			polling-delay = <1000>;		/* 1000ms */
+			thermal-sensors = <&pvtctl>;
+
+			trips {
+				cpu_crit: cpu_crit {
+					temperature = <110000>;	/* 110C */
+					hysteresis = <2000>;
+					type = "critical";
+				};
+				cpu_alert: cpu_alert {
+					temperature = <100000>;	/* 100C */
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert>;
+					cooling-device = <&cpu0 (-1) (-1)>;
+				};
+				map1 {
+					trip = <&cpu_alert>;
+					cooling-device = <&cpu2 (-1) (-1)>;
+				};
+			};
+		};
+	};
+
 	soc@0 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -410,6 +444,12 @@
 			watchdog {
 				compatible = "socionext,uniphier-wdt";
 			};
+
+			pvtctl: pvtctl {
+				compatible = "socionext,uniphier-ld20-thermal";
+				interrupts = <0 3 4>;
+				#thermal-sensor-cells = <0>;
+			};
 		};
 
 		nand: nand@68000000 {
-- 
2.7.4

[PATCH v4 2/2] arm64: dts: uniphier: add nodes of thermal monitor and thermal zone for LD20

[Kunihiko Hayashi]

Add nodes of thermal monitor and thermal zone for UniPhier LD20 SoC.
The thermal monitor is included in sysctrl.

Furthermore, since the reference board doesn't have a calibrated value of
thermal monitor, this patch gives the default value for LD20 reference
board.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 .../arm64/boot/dts/socionext/uniphier-ld20-ref.dts |  4 +++
 arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi   | 40 ++++++++++++++++++++++
 2 files changed, 44 insertions(+)

diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
index 1ca0c86..5bb63a2 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
@@ -50,3 +50,7 @@
 &i2c0 {
 	status = "okay";
 };
+
+&pvtctl {
+	socionext,tmod-calibration = <0x0f22 0x68ee>;
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
index a29c279..0f733ad 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
@@ -46,6 +46,7 @@
 			clocks = <&sys_clk 32>;
 			enable-method = "psci";
 			operating-points-v2 = <&cluster0_opp>;
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu at 1 {
@@ -64,6 +65,7 @@
 			clocks = <&sys_clk 33>;
 			enable-method = "psci";
 			operating-points-v2 = <&cluster1_opp>;
+			#cooling-cells = <2>;
 		};
 
 		cpu3: cpu at 101 {
@@ -173,6 +175,38 @@
 			     <1 10 4>;
 	};
 
+	thermal-zones {
+		cpu_thermal {
+			polling-delay-passive = <250>;	/* 250ms */
+			polling-delay = <1000>;		/* 1000ms */
+			thermal-sensors = <&pvtctl>;
+
+			trips {
+				cpu_crit: cpu_crit {
+					temperature = <110000>;	/* 110C */
+					hysteresis = <2000>;
+					type = "critical";
+				};
+				cpu_alert: cpu_alert {
+					temperature = <100000>;	/* 100C */
+					hysteresis = <2000>;
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert>;
+					cooling-device = <&cpu0 (-1) (-1)>;
+				};
+				map1 {
+					trip = <&cpu_alert>;
+					cooling-device = <&cpu2 (-1) (-1)>;
+				};
+			};
+		};
+	};
+
 	soc at 0 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -410,6 +444,12 @@
 			watchdog {
 				compatible = "socionext,uniphier-wdt";
 			};
+
+			pvtctl: pvtctl {
+				compatible = "socionext,uniphier-ld20-thermal";
+				interrupts = <0 3 4>;
+				#thermal-sensor-cells = <0>;
+			};
 		};
 
 		nand: nand at 68000000 {
-- 
2.7.4

Re: [PATCH v4 0/2] add thermal nodes for UniPhier SoCs

[Masahiro Yamada]

Hi.



2017-09-04 10:16 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:
> This series adds thermal nodes for UniPhier PXs2 and LD20 SoCs.
>
> Changes since v3:
> - rebase on top of linux-next


This repost is a spam.

I left some comments in v3,
but no response from you
nothing was reflected in v4.




> Changes since v2:
> - add the calibration value to device tree for LD20 reference board
>
> Changes since v1:
> - separate from driver's patchset[1]
> - add cooling-maps nodes on the device tree
> - fix an interrupt trigger to set 'level-triggered' according to
>   hardware specification
> - bring up threshold temperature for LD20 according to the spec sheet
> - add cpuN labels for reference in cooling-device property on PXs2 dts
>
> [1] https://lkml.org/lkml/2017/6/28/170
>
> Kunihiko Hayashi (2):
>   ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for
>     PXs2
>   arm64: dts: uniphier: add nodes of thermal monitor and thermal zone
>     for LD20
>
>  arch/arm/boot/dts/uniphier-pxs2.dtsi               | 43 ++++++++++++++++++++--
>  .../arm64/boot/dts/socionext/uniphier-ld20-ref.dts |  4 ++
>  arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi   | 40 ++++++++++++++++++++
>  3 files changed, 83 insertions(+), 4 deletions(-)
>
> --
> 2.7.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html



-- 
Best Regards
Masahiro Yamada

Re: [PATCH v4 0/2] add thermal nodes for UniPhier SoCs

[Masahiro Yamada]

Hi.



2017-09-04 10:16 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko-uWyLwvC0a2jby3iVrkZq2A@public.gmane.org>:
> This series adds thermal nodes for UniPhier PXs2 and LD20 SoCs.
>
> Changes since v3:
> - rebase on top of linux-next


This repost is a spam.

I left some comments in v3,
but no response from you
nothing was reflected in v4.




> Changes since v2:
> - add the calibration value to device tree for LD20 reference board
>
> Changes since v1:
> - separate from driver's patchset[1]
> - add cooling-maps nodes on the device tree
> - fix an interrupt trigger to set 'level-triggered' according to
>   hardware specification
> - bring up threshold temperature for LD20 according to the spec sheet
> - add cpuN labels for reference in cooling-device property on PXs2 dts
>
> [1] https://lkml.org/lkml/2017/6/28/170
>
> Kunihiko Hayashi (2):
>   ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for
>     PXs2
>   arm64: dts: uniphier: add nodes of thermal monitor and thermal zone
>     for LD20
>
>  arch/arm/boot/dts/uniphier-pxs2.dtsi               | 43 ++++++++++++++++++++--
>  .../arm64/boot/dts/socionext/uniphier-ld20-ref.dts |  4 ++
>  arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi   | 40 ++++++++++++++++++++
>  3 files changed, 83 insertions(+), 4 deletions(-)
>
> --
> 2.7.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html



-- 
Best Regards
Masahiro Yamada
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 0/2] add thermal nodes for UniPhier SoCs

[Masahiro Yamada]

Hi.



2017-09-04 10:16 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:
> This series adds thermal nodes for UniPhier PXs2 and LD20 SoCs.
>
> Changes since v3:
> - rebase on top of linux-next


This repost is a spam.

I left some comments in v3,
but no response from you
nothing was reflected in v4.




> Changes since v2:
> - add the calibration value to device tree for LD20 reference board
>
> Changes since v1:
> - separate from driver's patchset[1]
> - add cooling-maps nodes on the device tree
> - fix an interrupt trigger to set 'level-triggered' according to
>   hardware specification
> - bring up threshold temperature for LD20 according to the spec sheet
> - add cpuN labels for reference in cooling-device property on PXs2 dts
>
> [1] https://lkml.org/lkml/2017/6/28/170
>
> Kunihiko Hayashi (2):
>   ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for
>     PXs2
>   arm64: dts: uniphier: add nodes of thermal monitor and thermal zone
>     for LD20
>
>  arch/arm/boot/dts/uniphier-pxs2.dtsi               | 43 ++++++++++++++++++++--
>  .../arm64/boot/dts/socionext/uniphier-ld20-ref.dts |  4 ++
>  arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi   | 40 ++++++++++++++++++++
>  3 files changed, 83 insertions(+), 4 deletions(-)
>
> --
> 2.7.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html



-- 
Best Regards
Masahiro Yamada

Re: [PATCH v4 0/2] add thermal nodes for UniPhier SoCs

[hayashi.kunihiko]

On Mon, 4 Sep 2017 11:09:51 +0900 <yamada.masahiro@socionext.com> wrote:

> Hi.
> 
> 
> 
> 2017-09-04 10:16 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:
> > This series adds thermal nodes for UniPhier PXs2 and LD20 SoCs.
> >
> > Changes since v3:
> > - rebase on top of linux-next
> 
> 
> This repost is a spam.
> 
> I left some comments in v3,
> but no response from you
> nothing was reflected in v4.

Sorry I missed them. I'll reflect your comments and repost them.

Thank you,

> 
> 
> 
> 
> > Changes since v2:
> > - add the calibration value to device tree for LD20 reference board
> >
> > Changes since v1:
> > - separate from driver's patchset[1]
> > - add cooling-maps nodes on the device tree
> > - fix an interrupt trigger to set 'level-triggered' according to
> >   hardware specification
> > - bring up threshold temperature for LD20 according to the spec sheet
> > - add cpuN labels for reference in cooling-device property on PXs2 dts
> >
> > [1] https://lkml.org/lkml/2017/6/28/170
> >
> > Kunihiko Hayashi (2):
> >   ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for
> >     PXs2
> >   arm64: dts: uniphier: add nodes of thermal monitor and thermal zone
> >     for LD20
> >
> >  arch/arm/boot/dts/uniphier-pxs2.dtsi               | 43 ++++++++++++++++++++--
> >  .../arm64/boot/dts/socionext/uniphier-ld20-ref.dts |  4 ++
> >  arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi   | 40 ++++++++++++++++++++
> >  3 files changed, 83 insertions(+), 4 deletions(-)
> >
> > --
> > 2.7.4
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe devicetree" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 
> 
> 
> -- 
> Best Regards
> Masahiro Yamada

---
Kunihiko Hayashi
: hayashi.kunihiko@socionext.com

Re: [PATCH v4 0/2] add thermal nodes for UniPhier SoCs

[hayashi.kunihiko]

On Mon, 4 Sep 2017 11:09:51 +0900 <yamada.masahiro@socionext.com> wrote:

> Hi.
> 
> 
> 
> 2017-09-04 10:16 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:
> > This series adds thermal nodes for UniPhier PXs2 and LD20 SoCs.
> >
> > Changes since v3:
> > - rebase on top of linux-next
> 
> 
> This repost is a spam.
> 
> I left some comments in v3,
> but no response from you
> nothing was reflected in v4.

Sorry I missed them. I'll reflect your comments and repost them.

Thank you,

> 
> 
> 
> 
> > Changes since v2:
> > - add the calibration value to device tree for LD20 reference board
> >
> > Changes since v1:
> > - separate from driver's patchset[1]
> > - add cooling-maps nodes on the device tree
> > - fix an interrupt trigger to set 'level-triggered' according to
> >   hardware specification
> > - bring up threshold temperature for LD20 according to the spec sheet
> > - add cpuN labels for reference in cooling-device property on PXs2 dts
> >
> > [1] https://lkml.org/lkml/2017/6/28/170
> >
> > Kunihiko Hayashi (2):
> >   ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for
> >     PXs2
> >   arm64: dts: uniphier: add nodes of thermal monitor and thermal zone
> >     for LD20
> >
> >  arch/arm/boot/dts/uniphier-pxs2.dtsi               | 43 ++++++++++++++++++++--
> >  .../arm64/boot/dts/socionext/uniphier-ld20-ref.dts |  4 ++
> >  arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi   | 40 ++++++++++++++++++++
> >  3 files changed, 83 insertions(+), 4 deletions(-)
> >
> > --
> > 2.7.4
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe devicetree" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 
> 
> 
> -- 
> Best Regards
> Masahiro Yamada

---
Kunihiko Hayashi
: hayashi.kunihiko@socionext.com

[PATCH v4 0/2] add thermal nodes for UniPhier SoCs

[hayashi.kunihiko at socionext.com]

On Mon, 4 Sep 2017 11:09:51 +0900 <yamada.masahiro@socionext.com> wrote:

> Hi.
> 
> 
> 
> 2017-09-04 10:16 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:
> > This series adds thermal nodes for UniPhier PXs2 and LD20 SoCs.
> >
> > Changes since v3:
> > - rebase on top of linux-next
> 
> 
> This repost is a spam.
> 
> I left some comments in v3,
> but no response from you
> nothing was reflected in v4.

Sorry I missed them. I'll reflect your comments and repost them.

Thank you,

> 
> 
> 
> 
> > Changes since v2:
> > - add the calibration value to device tree for LD20 reference board
> >
> > Changes since v1:
> > - separate from driver's patchset[1]
> > - add cooling-maps nodes on the device tree
> > - fix an interrupt trigger to set 'level-triggered' according to
> >   hardware specification
> > - bring up threshold temperature for LD20 according to the spec sheet
> > - add cpuN labels for reference in cooling-device property on PXs2 dts
> >
> > [1] https://lkml.org/lkml/2017/6/28/170
> >
> > Kunihiko Hayashi (2):
> >   ARM: dts: uniphier: add nodes of thermal monitor and thermal zone for
> >     PXs2
> >   arm64: dts: uniphier: add nodes of thermal monitor and thermal zone
> >     for LD20
> >
> >  arch/arm/boot/dts/uniphier-pxs2.dtsi               | 43 ++++++++++++++++++++--
> >  .../arm64/boot/dts/socionext/uniphier-ld20-ref.dts |  4 ++
> >  arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi   | 40 ++++++++++++++++++++
> >  3 files changed, 83 insertions(+), 4 deletions(-)
> >
> > --
> > 2.7.4
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe devicetree" in
> > the body of a message to majordomo at vger.kernel.org
> > More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 
> 
> 
> -- 
> Best Regards
> Masahiro Yamada

---
Kunihiko Hayashi
: hayashi.kunihiko at socionext.com