[PATCH 1/7] arm64: dts: ls1012a: Move cpu_thermal out of bus node

[PATCH 1/7] arm64: dts: ls1012a: Move cpu_thermal out of bus node

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

Move cpu_thermal node from soc node to root node.

cpu_thermal node does not have any register properties and thus
shouldn't be placed on the bus.

This fixes the following build warnings with W=1:

arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 62 +++++++++++++-------------
 1 file changed, 31 insertions(+), 31 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
index 82b272f..4e98d05 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
@@ -118,6 +118,37 @@
 		mask = <0x02>;
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 0>;
+
+			trips {
+				cpu_alert: cpu-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit: cpu-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <2>;
@@ -304,37 +335,6 @@
 			#thermal-sensor-cells = <1>;
 		};
 
-		thermal-zones {
-			cpu_thermal: cpu-thermal {
-				polling-delay-passive = <1000>;
-				polling-delay = <5000>;
-				thermal-sensors = <&tmu 0>;
-
-				trips {
-					cpu_alert: cpu-alert {
-						temperature = <85000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-
-					cpu_crit: cpu-crit {
-						temperature = <95000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map0 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu0 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-				};
-			};
-		};
-
 		i2c0: i2c at 2180000 {
 			compatible = "fsl,vf610-i2c";
 			#address-cells = <1>;
-- 
2.7.4

[PATCH 2/7] arm64: dts: ls1043a: Move cpu_thermal out of bus node

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

Move cpu_thermal node from soc node to root node.

cpu_thermal node does not have any register properties and thus
shouldn't be placed on the bus.

This fixes the following build warnings with W=1:

arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi | 62 +++++++++++++-------------
 1 file changed, 31 insertions(+), 31 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
index 380e7c7..4d15e11 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
@@ -159,6 +159,37 @@
 		mask = <0x02>;
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+
+			thermal-sensors = <&tmu 3>;
+
+			trips {
+				cpu_alert: cpu-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit: cpu-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <1 13 0xf08>, /* Physical Secure PPI */
@@ -342,37 +373,6 @@
 			#thermal-sensor-cells = <1>;
 		};
 
-		thermal-zones {
-			cpu_thermal: cpu-thermal {
-				polling-delay-passive = <1000>;
-				polling-delay = <5000>;
-
-				thermal-sensors = <&tmu 3>;
-
-				trips {
-					cpu_alert: cpu-alert {
-						temperature = <85000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-					cpu_crit: cpu-crit {
-						temperature = <95000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map0 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu0 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-				};
-			};
-		};
-
 		qman: qman at 1880000 {
 			compatible = "fsl,qman";
 			reg = <0x0 0x1880000 0x0 0x10000>;
-- 
2.7.4

[PATCH 3/7] arm64: dts: ls1046a: Move cpu_thermal out of bus node

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

Move cpu_thermal node from soc node to root node.

cpu_thermal node does not have any register properties and thus
shouldn't be placed on the bus.

This fixes the following build warnings with W=1:

arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 62 +++++++++++++-------------
 1 file changed, 31 insertions(+), 31 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
index 06b5e12..3f8b62010 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
@@ -147,6 +147,37 @@
 		mask = <0x02>;
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 3>;
+
+			trips {
+				cpu_alert: cpu-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit: cpu-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(0xf) |
@@ -362,37 +393,6 @@
 			#thermal-sensor-cells = <1>;
 		};
 
-		thermal-zones {
-			cpu_thermal: cpu-thermal {
-				polling-delay-passive = <1000>;
-				polling-delay = <5000>;
-				thermal-sensors = <&tmu 3>;
-
-				trips {
-					cpu_alert: cpu-alert {
-						temperature = <85000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-
-					cpu_crit: cpu-crit {
-						temperature = <95000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map0 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu0 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-				};
-			};
-		};
-
 		dspi: dspi at 2100000 {
 			compatible = "fsl,ls1021a-v1.0-dspi";
 			#address-cells = <1>;
-- 
2.7.4

[PATCH 4/7] arm64: dts: ls1088a: Move cpu_thermal out of bus node

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

Move cpu_thermal node from soc node to root node.

cpu_thermal node does not have any register properties and thus
shouldn't be placed on the bus.

This fixes the following build warnings with W=1:

arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 76 +++++++++++++-------------
 1 file changed, 38 insertions(+), 38 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index bd80e9a..bbbfd53 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -158,6 +158,44 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&tmu 0>;
+
+			trips {
+				cpu_alert: cpu-alert {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit: cpu-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu4 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>,/* Physical Secure PPI */
@@ -238,44 +276,6 @@
 			#thermal-sensor-cells = <1>;
 		};
 
-		thermal-zones {
-			cpu_thermal: cpu-thermal {
-				polling-delay-passive = <1000>;
-				polling-delay = <5000>;
-				thermal-sensors = <&tmu 0>;
-
-				trips {
-					cpu_alert: cpu-alert {
-						temperature = <85000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-
-					cpu_crit: cpu-crit {
-						temperature = <95000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map0 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu0 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-
-					map1 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu4 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-				};
-			};
-		};
-
 		duart0: serial at 21c0500 {
 			compatible = "fsl,ns16550", "ns16550a";
 			reg = <0x0 0x21c0500 0x0 0x100>;
-- 
2.7.4

[PATCH 5/7] arm64: dts: ls208xa: Move cpu_thermal out of bus node

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

Move cpu_thermal node from soc node to root node.

cpu_thermal node does not have any register properties and thus
shouldn't be placed on the bus.

This fixes the following build warnings with W=1:

arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 98 +++++++++++++-------------
 1 file changed, 49 insertions(+), 49 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
index f3a40af..137ef4d 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -111,6 +111,55 @@
 		mask = <0x2>;
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+
+			thermal-sensors = <&tmu 4>;
+
+			trips {
+				cpu_alert: cpu-alert {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit: cpu-crit {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+				map1 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu2 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+				map2 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu4 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+				map3 {
+					trip = <&cpu_alert>;
+					cooling-device =
+						<&cpu6 THERMAL_NO_LIMIT
+						THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <1 13 4>, /* Physical Secure PPI, active-low */
@@ -194,55 +243,6 @@
 			#thermal-sensor-cells = <1>;
 		};
 
-		thermal-zones {
-			cpu_thermal: cpu-thermal {
-				polling-delay-passive = <1000>;
-				polling-delay = <5000>;
-
-				thermal-sensors = <&tmu 4>;
-
-				trips {
-					cpu_alert: cpu-alert {
-						temperature = <75000>;
-						hysteresis = <2000>;
-						type = "passive";
-					};
-					cpu_crit: cpu-crit {
-						temperature = <85000>;
-						hysteresis = <2000>;
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map0 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu0 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-					map1 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu2 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-					map2 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu4 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-					map3 {
-						trip = <&cpu_alert>;
-						cooling-device =
-							<&cpu6 THERMAL_NO_LIMIT
-							THERMAL_NO_LIMIT>;
-					};
-				};
-			};
-		};
-
 		serial0: serial at 21c0500 {
 			compatible = "fsl,ns16550", "ns16550a";
 			reg = <0x0 0x21c0500 0x0 0x100>;
-- 
2.7.4

[PATCH 6/7] arm64: dts: ls208xa-qds: Pass unit name to dspi child nodes

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

Pass unit name to dspi child nodes to fix the following build warnings
with W=1:

arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dtb: Warning (unit_address_vs_reg): Node /soc/dspi at 2100000/n25q128a has a reg or ranges property, but no unit name
arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dtb: Warning (unit_address_vs_reg): Node /soc/dspi at 2100000/sst25wf040b has a reg or ranges property, but no unit name
arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dtb: Warning (unit_address_vs_reg): Node /soc/dspi at 2100000/en25s64 has a reg or ranges property, but no unit name

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
index b237446..a1a5ccb 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
@@ -140,21 +140,21 @@
 
 &dspi {
 	status = "okay";
-	dflash0: n25q128a {
+	dflash0: n25q128a at 0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p80";
 		spi-max-frequency = <3000000>;
 		reg = <0>;
 	};
-	dflash1: sst25wf040b {
+	dflash1: sst25wf040b at 1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p80";
 		spi-max-frequency = <3000000>;
 		reg = <1>;
 	};
-	dflash2: en25s64 {
+	dflash2: en25s64 at 2 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p80";
-- 
2.7.4

[PATCH 7/7] arm64: ls208xa-qds: Fix the 'reg' property

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@nxp.com>

The 'reg' property should match the corresponding @ address, so
fix it accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
index a1a5ccb..1de6188 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
@@ -177,7 +177,7 @@
 		#size-cells = <1>;
 		compatible = "st,m25p80";
 		spi-max-frequency = <20000000>;
-		reg = <0>;
+		reg = <2>;
 	};
 };
 
-- 
2.7.4

[PATCH 1/7] arm64: dts: ls1012a: Move cpu_thermal out of bus node

[Shawn Guo]

On Mon, Feb 05, 2018 at 04:45:32PM -0200, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam@nxp.com>
> 
> Move cpu_thermal node from soc node to root node.
> 
> cpu_thermal node does not have any register properties and thus
> shouldn't be placed on the bus.
> 
> This fixes the following build warnings with W=1:
> 
> arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dtb: Warning (simple_bus_reg): Node /soc/thermal-zones missing or empty reg/ranges property
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

Applied all, thanks.