[U-Boot] [PATCH v1 0/4] DRA7x: add support for HS200 in SPL

[U-Boot] [PATCH v1 0/4] DRA7x: add support for HS200 in SPL

[Jean-Jacques Hiblot]

HS200 support in SPL, while not mandatory, is a desirable feature if falcon
mode is enabled as it will speed up the loading of big images.

All code is in place to support high speed mmc modes in the SPL, but a bit
of configuration is required to use it.

This is done 3 steps:
- enable HS200 in mmc core
- enable multi-dtb in SPL. This is required because some information is
  available only in the dtb and vary across SOCs
- make sure that the information is available in the SPL version of the dtbs that are
  stripped-down versions to reduce their size.

dra7xx_hs_evm_config hasn't been updated on purpose because it doesn't
enable OS_BOOT and HS200 support makes sense mostly in this use case.

This series also provides the missing pinctrl/IOdelay properties for the
dra76-evm platform. The DTSI file has been copied from linux 4.14

The whole series adds about 2.1kB to the SPL.

This series has been tested on:
- dra76-evm
- dra7-evm
- dra72-evm rev C
- dra71-evm



Jean-Jacques Hiblot (4):
  ARM: dts: dra76x: create a common file with MMC/SD IOdelay data
  ARM: dts: dra76-evm: shift to using common IOdelay data
  configs: dra7xx_evm: Enable support for the HS200 mmc mode in the SPL
  ARM: dts: dra7x: Make pinctrl and IOdelays for MMC2 available in SPL

 arch/arm/dts/dra7-evm-u-boot.dtsi       |  20 +++
 arch/arm/dts/dra71-evm-u-boot.dtsi      |  24 +++
 arch/arm/dts/dra72-evm-revc-u-boot.dtsi |  24 +++
 arch/arm/dts/dra76-evm-u-boot.dtsi      |  12 ++
 arch/arm/dts/dra76-evm.dts              |  51 +-----
 arch/arm/dts/dra76x-mmc-iodelay.dtsi    | 285 ++++++++++++++++++++++++++++++++
 configs/dra7xx_evm_defconfig            |   3 +
 7 files changed, 376 insertions(+), 43 deletions(-)
 create mode 100644 arch/arm/dts/dra76x-mmc-iodelay.dtsi

-- 
1.9.1

[U-Boot] [PATCH v1 1/4] ARM: dts: dra76x: create a common file with MMC/SD IOdelay data

[Jean-Jacques Hiblot]

Add a common device-tree include file with MMC/SD IOdelay data
for DRA76x SoC based on the linux DTSI file.

In the most common case, IOdelay data available in datamanual
can directly be used. This file caters to that common case.

Data is based on DRA76x datamanual, SPRS993A, revised July 2017.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
---

 arch/arm/dts/dra76x-mmc-iodelay.dtsi | 285 +++++++++++++++++++++++++++++++++++
 1 file changed, 285 insertions(+)
 create mode 100644 arch/arm/dts/dra76x-mmc-iodelay.dtsi

diff --git a/arch/arm/dts/dra76x-mmc-iodelay.dtsi b/arch/arm/dts/dra76x-mmc-iodelay.dtsi
new file mode 100644
index 0000000..baba7b0
--- /dev/null
+++ b/arch/arm/dts/dra76x-mmc-iodelay.dtsi
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Texas Instruments
+// MMC IOdelay values for TI's DRA76x and AM576x SoCs.
+// Author: Sekhar Nori <nsekhar@ti.com>
+
+/*
+ * Rules for modifying this file:
+ * a) Update of this file should typically correspond to a datamanual revision.
+ *    Datamanual revision that was used should be updated in comment below.
+ *    If there is no update to datamanual, do not update the values. If you
+ *    need to use values different from that recommended by the datamanual
+ *    for your design, then you should consider adding values to the device-
+ *    -tree file for your board directly.
+ * b) We keep the mode names as close to the datamanual as possible. So
+ *    if the manual calls a mode, DDR50, or DDR or DDR 1.8v or DDR 3.3v,
+ *    we follow that in code too.
+ * c) If the values change between multiple revisions of silicon, we add
+ *    a revision tag to both the new and old entry. Use 'rev11' for PG 1.1,
+ *    'rev20' for PG 2.0 and so on.
+ * d) The node name and node label should be the exact same string. This is
+ *    to curb naming creativity and achieve consistency.
+ *
+ * Datamanual Revisions:
+ *
+ * DRA76x Silicon Revision 1.0: SPRS993A, Revised July 2017
+ *
+ */
+
+&dra7_pmx_core {
+	mmc1_pins_default: mmc1_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_hs: mmc1_pins_hs {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE11 | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_sdr50: mmc1_pins_sdr50 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_VIRTUAL_MODE10 | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc1_pins_ddr50: mmc1_pins_ddr50 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)	/* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc2_pins_default: mmc2_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc2_pins_hs200: mmc2_pins_hs200 {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	mmc3_pins_default: mmc3_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x377c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_clk.mmc3_clk */
+			DRA7XX_CORE_IOPAD(0x3780, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_cmd.mmc3_cmd */
+			DRA7XX_CORE_IOPAD(0x3784, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat0.mmc3_dat0 */
+			DRA7XX_CORE_IOPAD(0x3788, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat1.mmc3_dat1 */
+			DRA7XX_CORE_IOPAD(0x378c, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat2.mmc3_dat2 */
+			DRA7XX_CORE_IOPAD(0x3790, (PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE0)) /* mmc3_dat3.mmc3_dat3 */
+		>;
+	};
+
+	mmc4_pins_hs: mmc4_pins_hs {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_ctsn.mmc4_clk */
+			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart1_rtsn.mmc4_cmd */
+			DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rxd.mmc4_dat0 */
+			DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_txd.mmc4_dat1 */
+			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_ctsn.mmc4_dat2 */
+			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT_PULLUP | MODE_SELECT | MUX_MODE3) /* uart2_rtsn.mmc4_dat3 */
+		>;
+	};
+};
+
+&dra7_iodelay_core {
+
+	/* Corresponds to MMC1_DDR_MANUAL1 in datamanual */
+	mmc1_iodelay_ddr_conf: mmc1_iodelay_ddr_conf {
+		pinctrl-pin-array = <
+			0x618 A_DELAY_PS(489) G_DELAY_PS(0)	/* CFG_MMC1_CLK_IN */
+			0x624 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_IN */
+			0x630 A_DELAY_PS(374) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_IN */
+			0x63c A_DELAY_PS(31) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_IN */
+			0x648 A_DELAY_PS(56) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_IN */
+			0x654 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_IN */
+			0x620 A_DELAY_PS(1355) G_DELAY_PS(0)	/* CFG_MMC1_CLK_OUT */
+			0x628 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x62c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x634 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x638 A_DELAY_PS(0) G_DELAY_PS(4)	/* CFG_MMC1_DAT0_OUT */
+			0x640 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x644 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x64c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x650 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x658 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+			0x65c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC1_SDR104_MANUAL1 in datamanual */
+	mmc1_iodelay_sdr104_conf: mmc1_iodelay_sdr104_conf {
+		pinctrl-pin-array = <
+			0x620 A_DELAY_PS(892) G_DELAY_PS(0)	/* CFG_MMC1_CLK_OUT */
+			0x628 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OEN */
+			0x62c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_CMD_OUT */
+			0x634 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OEN */
+			0x638 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT0_OUT */
+			0x640 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OEN */
+			0x644 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT1_OUT */
+			0x64c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OEN */
+			0x650 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT2_OUT */
+			0x658 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OEN */
+			0x65c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC1_DAT3_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC2_HS200_MANUAL1 in datamanual */
+	mmc2_iodelay_hs200_conf: mmc2_iodelay_hs200_conf {
+		pinctrl-pin-array = <
+			0x190 A_DELAY_PS(384) G_DELAY_PS(0)       /* CFG_GPMC_A19_OEN */
+			0x194 A_DELAY_PS(0) G_DELAY_PS(174)       /* CFG_GPMC_A19_OUT */
+			0x1a8 A_DELAY_PS(410) G_DELAY_PS(0)       /* CFG_GPMC_A20_OEN */
+			0x1ac A_DELAY_PS(85) G_DELAY_PS(0)        /* CFG_GPMC_A20_OUT */
+			0x1b4 A_DELAY_PS(468) G_DELAY_PS(0)       /* CFG_GPMC_A21_OEN */
+			0x1b8 A_DELAY_PS(139) G_DELAY_PS(0)       /* CFG_GPMC_A21_OUT */
+			0x1c0 A_DELAY_PS(676) G_DELAY_PS(0)       /* CFG_GPMC_A22_OEN */
+			0x1c4 A_DELAY_PS(69) G_DELAY_PS(0)        /* CFG_GPMC_A22_OUT */
+			0x1d0 A_DELAY_PS(1062) G_DELAY_PS(154)	  /* CFG_GPMC_A23_OUT */
+			0x1d8 A_DELAY_PS(640) G_DELAY_PS(0)       /* CFG_GPMC_A24_OEN */
+			0x1dc A_DELAY_PS(0) G_DELAY_PS(0)         /* CFG_GPMC_A24_OUT */
+			0x1e4 A_DELAY_PS(356) G_DELAY_PS(0)       /* CFG_GPMC_A25_OEN */
+			0x1e8 A_DELAY_PS(0) G_DELAY_PS(0)         /* CFG_GPMC_A25_OUT */
+			0x1f0 A_DELAY_PS(579) G_DELAY_PS(0)       /* CFG_GPMC_A26_OEN */
+			0x1f4 A_DELAY_PS(0) G_DELAY_PS(0)         /* CFG_GPMC_A26_OUT */
+			0x1fc A_DELAY_PS(435) G_DELAY_PS(0)       /* CFG_GPMC_A27_OEN */
+			0x200 A_DELAY_PS(36) G_DELAY_PS(0)        /* CFG_GPMC_A27_OUT */
+			0x364 A_DELAY_PS(759) G_DELAY_PS(0)       /* CFG_GPMC_CS1_OEN */
+			0x368 A_DELAY_PS(72) G_DELAY_PS(0)        /* CFG_GPMC_CS1_OUT */
+	      >;
+	};
+
+	/* Corresponds to MMC3_MANUAL1 in datamanual */
+	mmc3_iodelay_manual1_conf: mmc3_iodelay_manual1_conf {
+		pinctrl-pin-array = <
+			0x678 A_DELAY_PS(0) G_DELAY_PS(386)	/* CFG_MMC3_CLK_IN */
+			0x680 A_DELAY_PS(605) G_DELAY_PS(0)	/* CFG_MMC3_CLK_OUT */
+			0x684 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_IN */
+			0x688 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_OEN */
+			0x68c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_OUT */
+			0x690 A_DELAY_PS(171) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_IN */
+			0x694 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_OEN */
+			0x698 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_OUT */
+			0x69c A_DELAY_PS(221) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_IN */
+			0x6a0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_OEN */
+			0x6a4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_OUT */
+			0x6a8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_IN */
+			0x6ac A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_OEN */
+			0x6b0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_OUT */
+			0x6b4 A_DELAY_PS(474) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_IN */
+			0x6b8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_OEN */
+			0x6bc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC3_MANUAL2 in datamanual */
+	mmc3_iodelay_sdr50_conf: mmc3_iodelay_sdr50_conf {
+		pinctrl-pin-array = <
+			0x678 A_DELAY_PS(852) G_DELAY_PS(0)	/* CFG_MMC3_CLK_IN */
+			0x680 A_DELAY_PS(94) G_DELAY_PS(0)	/* CFG_MMC3_CLK_OUT */
+			0x684 A_DELAY_PS(122) G_DELAY_PS(0)	/* CFG_MMC3_CMD_IN */
+			0x688 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_OEN */
+			0x68c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_CMD_OUT */
+			0x690 A_DELAY_PS(91) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_IN */
+			0x694 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_OEN */
+			0x698 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT0_OUT */
+			0x69c A_DELAY_PS(57) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_IN */
+			0x6a0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_OEN */
+			0x6a4 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT1_OUT */
+			0x6a8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_IN */
+			0x6ac A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_OEN */
+			0x6b0 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT2_OUT */
+			0x6b4 A_DELAY_PS(375) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_IN */
+			0x6b8 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_OEN */
+			0x6bc A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_MMC3_DAT3_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC4_MANUAL1 in datamanual */
+	mmc4_iodelay_manual1_conf: mmc4_iodelay_manual1_conf {
+		pinctrl-pin-array = <
+			0x840 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_CTSN_IN */
+			0x848 A_DELAY_PS(1147) G_DELAY_PS(0)	/* CFG_UART1_CTSN_OUT */
+			0x84c A_DELAY_PS(1834) G_DELAY_PS(0)	/* CFG_UART1_RTSN_IN */
+			0x850 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OEN */
+			0x854 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OUT */
+			0x870 A_DELAY_PS(2165) G_DELAY_PS(0)	/* CFG_UART2_CTSN_IN */
+			0x874 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OEN */
+			0x878 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OUT */
+			0x87c A_DELAY_PS(1929) G_DELAY_PS(64)	/* CFG_UART2_RTSN_IN */
+			0x880 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OEN */
+			0x884 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OUT */
+			0x888 A_DELAY_PS(1935) G_DELAY_PS(128)	/* CFG_UART2_RXD_IN */
+			0x88c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OEN */
+			0x890 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OUT */
+			0x894 A_DELAY_PS(2172) G_DELAY_PS(44)	/* CFG_UART2_TXD_IN */
+			0x898 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OEN */
+			0x89c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OUT */
+		>;
+	};
+
+	/* Corresponds to MMC4_DS_MANUAL1 in datamanual */
+	mmc4_iodelay_default_conf: mmc4_iodelay_default_conf {
+		pinctrl-pin-array = <
+			0x840 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_CTSN_IN */
+			0x848 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_CTSN_OUT */
+			0x84c A_DELAY_PS(307) G_DELAY_PS(0)	/* CFG_UART1_RTSN_IN */
+			0x850 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OEN */
+			0x854 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART1_RTSN_OUT */
+			0x870 A_DELAY_PS(785) G_DELAY_PS(0)	/* CFG_UART2_CTSN_IN */
+			0x874 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OEN */
+			0x878 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_CTSN_OUT */
+			0x87c A_DELAY_PS(613) G_DELAY_PS(0)	/* CFG_UART2_RTSN_IN */
+			0x880 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OEN */
+			0x884 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RTSN_OUT */
+			0x888 A_DELAY_PS(683) G_DELAY_PS(0)	/* CFG_UART2_RXD_IN */
+			0x88c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OEN */
+			0x890 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_RXD_OUT */
+			0x894 A_DELAY_PS(835) G_DELAY_PS(0)	/* CFG_UART2_TXD_IN */
+			0x898 A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OEN */
+			0x89c A_DELAY_PS(0) G_DELAY_PS(0)	/* CFG_UART2_TXD_OUT */
+		>;
+	};
+};
-- 
1.9.1

[U-Boot] [PATCH v1 2/4] ARM: dts: dra76-evm: shift to using common IOdelay data

[Jean-Jacques Hiblot]

Now that we have a device-tree include file with common
MMC/SD IOdelay data for DRA76x SoC, shift the EVM device-tree
file to using that.
Also fix the name of the IO voltage regulator for mmc1.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
---

 arch/arm/dts/dra76-evm.dts | 51 ++++++++--------------------------------------
 1 file changed, 8 insertions(+), 43 deletions(-)

diff --git a/arch/arm/dts/dra76-evm.dts b/arch/arm/dts/dra76-evm.dts
index b024a65..a1f289f 100644
--- a/arch/arm/dts/dra76-evm.dts
+++ b/arch/arm/dts/dra76-evm.dts
@@ -9,6 +9,7 @@
 
 #include "dra76x.dtsi"
 #include "dra7-evm-common.dtsi"
+#include "dra76x-mmc-iodelay.dtsi"
 #include <dt-bindings/net/ti-dp83867.h>
 
 / {
@@ -100,46 +101,6 @@
 	};
 };
 
-&dra7_pmx_core {
-	mmc1_pins_default: mmc1_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc1_pins_sdr12: pinmux_mmc1_sdr12_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.clk */
-			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.cmd */
-			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.dat0 */
-			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.dat1 */
-			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.dat2 */
-			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.dat3 */
-		>;
-	};
-
-	mmc2_pins_default: mmc2_pins_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
-			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
-			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
-			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
-			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
-			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
-			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
-			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
-			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
-			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
-		>;
-	};
-};
-
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -345,23 +306,27 @@
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vio_3v3_sd>;
-	vmmc_aux-supply = <&ldo4_reg>;
+	vqmmc-supply = <&ldo4_reg>;
 	bus-width = <4>;
 	/*
 	 * SDCD signal is not being used here - using the fact that GPIO mode
 	 * is always hardwired.
 	 */
 	cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "hs";
 	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_hs>;
 };
 
 &mmc2 {
 	status = "okay";
 	vmmc-supply = <&vio_1v8>;
 	bus-width = <8>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "hs", "ddr_1_8v", "hs200_1_8v";
 	pinctrl-0 = <&mmc2_pins_default>;
+	pinctrl-1 = <&mmc2_pins_default>;
+	pinctrl-2 = <&mmc2_pins_default>;
+	pinctrl-3 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_conf>;
 };
 
 /* No RTC on this device */
-- 
1.9.1

[U-Boot] [PATCH v1 3/4] configs: dra7xx_evm: Enable support for the HS200 mmc mode in the SPL

[Jean-Jacques Hiblot]

Beside enabling the support for HS200 in mmc core, enabling the HS200
support in the SPL requires multi-dtb support in the SPL because pinctrl
and IOdelays vary across SOCs.

Also we need to make sure that the pinctrl properties arenot removed from
the dts by setting CONFIG_OF_SPL_REMOVE_PROPS to remove only clocks and
interrupts properties.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
---

 configs/dra7xx_evm_defconfig | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/configs/dra7xx_evm_defconfig b/configs/dra7xx_evm_defconfig
index 1cc614f..2b83a0c 100644
--- a/configs/dra7xx_evm_defconfig
+++ b/configs/dra7xx_evm_defconfig
@@ -34,6 +34,8 @@ CONFIG_CMD_SPL=y
 CONFIG_OF_CONTROL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_OF_LIST="dra7-evm dra72-evm dra72-evm-revc dra71-evm dra76-evm"
+CONFIG_SPL_MULTI_DTB_FIT=y
+CONFIG_OF_SPL_REMOVE_PROPS="clocks clock-names interrupt-parent"
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_DM=y
 CONFIG_SPL_DM=y
@@ -52,6 +54,7 @@ CONFIG_DM_MMC=y
 CONFIG_MMC_IO_VOLTAGE=y
 CONFIG_MMC_UHS_SUPPORT=y
 CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_SPL_MMC_HS200_SUPPORT=y
 CONFIG_MMC_OMAP_HS=y
 CONFIG_DM_SPI_FLASH=y
 CONFIG_SPI_FLASH=y
-- 
1.9.1

[U-Boot] [PATCH v1 4/4] ARM: dts: dra7x: Make pinctrl and IOdelays for MMC2 available in SPL

[Jean-Jacques Hiblot]

The SPL can't use high speed MMC modes if the associated pinctrl and
IOdelays are described in the DTS.
Make them available in SPL by tagging the nodes with 'u-boot,dm-spl;'

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

---

 arch/arm/dts/dra7-evm-u-boot.dtsi       | 20 ++++++++++++++++++++
 arch/arm/dts/dra71-evm-u-boot.dtsi      | 24 ++++++++++++++++++++++++
 arch/arm/dts/dra72-evm-revc-u-boot.dtsi | 24 ++++++++++++++++++++++++
 arch/arm/dts/dra76-evm-u-boot.dtsi      | 12 ++++++++++++
 4 files changed, 80 insertions(+)

diff --git a/arch/arm/dts/dra7-evm-u-boot.dtsi b/arch/arm/dts/dra7-evm-u-boot.dtsi
index 62ef830..3e7da7c 100644
--- a/arch/arm/dts/dra7-evm-u-boot.dtsi
+++ b/arch/arm/dts/dra7-evm-u-boot.dtsi
@@ -13,3 +13,23 @@
 &pcf_hdmi{
 	u-boot,i2c-offset-len = <0>;
 };
+
+&mmc2_pins_default {
+	u-boot,dm-spl;
+};
+
+&mmc2_pins_hs {
+	u-boot,dm-spl;
+};
+
+&mmc2_pins_ddr_rev20 {
+	u-boot,dm-spl;
+};
+
+&mmc2_pins_hs200 {
+	u-boot,dm-spl;
+};
+
+&mmc2_iodelay_hs200_rev20_conf {
+	u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/dra71-evm-u-boot.dtsi b/arch/arm/dts/dra71-evm-u-boot.dtsi
index 8ae64c0..e2ab0bb 100644
--- a/arch/arm/dts/dra71-evm-u-boot.dtsi
+++ b/arch/arm/dts/dra71-evm-u-boot.dtsi
@@ -21,3 +21,27 @@
 &cpsw_emac1 {
 	phy-handle = <&dp83867_1>;
 };
+
+&mmc2_pins_default {
+	u-boot,dm-spl;
+};
+
+&mmc2_pins_hs {
+	u-boot,dm-spl;
+};
+
+&mmc2_pins_ddr_rev20 {
+	u-boot,dm-spl;
+};
+
+&mmc2_iodelay_ddr_conf {
+	u-boot,dm-spl;
+};
+
+&mmc2_pins_hs200 {
+	u-boot,dm-spl;
+};
+
+&mmc2_iodelay_hs200_rev20_conf {
+	u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/dra72-evm-revc-u-boot.dtsi b/arch/arm/dts/dra72-evm-revc-u-boot.dtsi
index 8ae64c0..e2ab0bb 100644
--- a/arch/arm/dts/dra72-evm-revc-u-boot.dtsi
+++ b/arch/arm/dts/dra72-evm-revc-u-boot.dtsi
@@ -21,3 +21,27 @@
 &cpsw_emac1 {
 	phy-handle = <&dp83867_1>;
 };
+
+&mmc2_pins_default {
+	u-boot,dm-spl;
+};
+
+&mmc2_pins_hs {
+	u-boot,dm-spl;
+};
+
+&mmc2_pins_ddr_rev20 {
+	u-boot,dm-spl;
+};
+
+&mmc2_iodelay_ddr_conf {
+	u-boot,dm-spl;
+};
+
+&mmc2_pins_hs200 {
+	u-boot,dm-spl;
+};
+
+&mmc2_iodelay_hs200_rev20_conf {
+	u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/dra76-evm-u-boot.dtsi b/arch/arm/dts/dra76-evm-u-boot.dtsi
index b007f78..a5a0694 100644
--- a/arch/arm/dts/dra76-evm-u-boot.dtsi
+++ b/arch/arm/dts/dra76-evm-u-boot.dtsi
@@ -13,3 +13,15 @@
 &cpsw_emac1 {
 	phy-handle = <&dp83867_1>;
 };
+
+&mmc2_pins_default {
+	u-boot,dm-spl;
+};
+
+&mmc2_pins_hs200 {
+	u-boot,dm-spl;
+};
+
+&mmc2_iodelay_hs200_conf {
+	u-boot,dm-spl;
+};
-- 
1.9.1

[U-Boot] [U-Boot, v1, 1/4] ARM: dts: dra76x: create a common file with MMC/SD IOdelay data

[Tom Rini]

On Tue, Feb 27, 2018 at 05:05:47PM +0100, Jean-Jacques Hiblot wrote:

> Add a common device-tree include file with MMC/SD IOdelay data
> for DRA76x SoC based on the linux DTSI file.
> 
> In the most common case, IOdelay data available in datamanual
> can directly be used. This file caters to that common case.
> 
> Data is based on DRA76x datamanual, SPRS993A, revised July 2017.
> 
> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180314/737827ea/attachment.sig>

[U-Boot] [U-Boot, v1, 2/4] ARM: dts: dra76-evm: shift to using common IOdelay data

[Tom Rini]

On Tue, Feb 27, 2018 at 05:05:48PM +0100, Jean-Jacques Hiblot wrote:

> Now that we have a device-tree include file with common
> MMC/SD IOdelay data for DRA76x SoC, shift the EVM device-tree
> file to using that.
> Also fix the name of the IO voltage regulator for mmc1.
> 
> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180314/9a29d4a9/attachment.sig>

[U-Boot] [U-Boot, v1, 3/4] configs: dra7xx_evm: Enable support for the HS200 mmc mode in the SPL

[Tom Rini]

On Tue, Feb 27, 2018 at 05:05:49PM +0100, Jean-Jacques Hiblot wrote:

> Beside enabling the support for HS200 in mmc core, enabling the HS200
> support in the SPL requires multi-dtb support in the SPL because pinctrl
> and IOdelays vary across SOCs.
> 
> Also we need to make sure that the pinctrl properties arenot removed from
> the dts by setting CONFIG_OF_SPL_REMOVE_PROPS to remove only clocks and
> interrupts properties.
> 
> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180314/8a4e5dd1/attachment.sig>

[U-Boot] [U-Boot, v1, 4/4] ARM: dts: dra7x: Make pinctrl and IOdelays for MMC2 available in SPL

[Tom Rini]

On Tue, Feb 27, 2018 at 05:05:50PM +0100, Jean-Jacques Hiblot wrote:

> The SPL can't use high speed MMC modes if the associated pinctrl and
> IOdelays are described in the DTS.
> Make them available in SPL by tagging the nodes with 'u-boot,dm-spl;'
> 
> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

Applied to u-boot/master, thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180314/7c633e81/attachment.sig>