[PATCH 1/6] phy: qcom-qmp: Enable pipe_clk before checking USB3 PHY_STATUS

[PATCH 1/6] phy: qcom-qmp: Enable pipe_clk before checking USB3 PHY_STATUS

[Manu Gautam]

QMP PHY for USB mode requires pipe_clk for calibration and PLL lock
to take place. This lock is output from PHY to GCC clock_ctl and then
fed back to QMP PHY and is output from PHY only after PHY is reset
and initialized, hence it can't be enabled too early in initialization
sequence.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 6470c5d..73aa282 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -797,8 +797,13 @@ static int qcom_qmp_phy_poweron(struct phy *phy)
 {
 	struct qmp_phy *qphy = phy_get_drvdata(phy);
 	struct qcom_qmp *qmp = qphy->qmp;
+	const struct qmp_phy_cfg *cfg = qmp->cfg;
 	int ret;
 
+	/* Not needed for USB3 PHY as pipe_clk is enabled from phy_init */
+	if (cfg->type == PHY_TYPE_USB3)
+		return 0;
+
 	ret = clk_prepare_enable(qphy->pipe_clk);
 	if (ret)
 		dev_err(qmp->dev, "pipe_clk enable failed, err=%d\n", ret);
@@ -1008,6 +1013,19 @@ static int qcom_qmp_phy_init(struct phy *phy)
 	status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
 	mask = cfg->mask_pcs_ready;
 
+	/* USB3 PHY requires pipe_clk for PLL lock and calibration */
+	if (cfg->type == PHY_TYPE_USB3) {
+		ret = clk_prepare_enable(qphy->pipe_clk);
+		if (ret)
+			dev_err(qmp->dev, "pipe_clk enable err=%d\n", ret);
+		/*
+		 * Ignore this error as pipe_clk might take some time to get
+		 * enabled. In any case following check for PHY PLL lock would
+		 * timeout below if there is a fatal error and clock is not fed
+		 * to PHY
+		 */
+	}
+
 	ret = readl_poll_timeout(status, val, !(val & mask), 1,
 				 PHY_INIT_COMPLETE_TIMEOUT);
 	if (ret) {
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 1/6] phy: qcom-qmp: Enable pipe_clk before checking USB3 PHY_STATUS

[Manu Gautam]

QMP PHY for USB mode requires pipe_clk for calibration and PLL lock
to take place. This lock is output from PHY to GCC clock_ctl and then
fed back to QMP PHY and is output from PHY only after PHY is reset
and initialized, hence it can't be enabled too early in initialization
sequence.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 6470c5d..73aa282 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -797,8 +797,13 @@ static int qcom_qmp_phy_poweron(struct phy *phy)
 {
 	struct qmp_phy *qphy = phy_get_drvdata(phy);
 	struct qcom_qmp *qmp = qphy->qmp;
+	const struct qmp_phy_cfg *cfg = qmp->cfg;
 	int ret;
 
+	/* Not needed for USB3 PHY as pipe_clk is enabled from phy_init */
+	if (cfg->type == PHY_TYPE_USB3)
+		return 0;
+
 	ret = clk_prepare_enable(qphy->pipe_clk);
 	if (ret)
 		dev_err(qmp->dev, "pipe_clk enable failed, err=%d\n", ret);
@@ -1008,6 +1013,19 @@ static int qcom_qmp_phy_init(struct phy *phy)
 	status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
 	mask = cfg->mask_pcs_ready;
 
+	/* USB3 PHY requires pipe_clk for PLL lock and calibration */
+	if (cfg->type == PHY_TYPE_USB3) {
+		ret = clk_prepare_enable(qphy->pipe_clk);
+		if (ret)
+			dev_err(qmp->dev, "pipe_clk enable err=%d\n", ret);
+		/*
+		 * Ignore this error as pipe_clk might take some time to get
+		 * enabled. In any case following check for PHY PLL lock would
+		 * timeout below if there is a fatal error and clock is not fed
+		 * to PHY
+		 */
+	}
+
 	ret = readl_poll_timeout(status, val, !(val & mask), 1,
 				 PHY_INIT_COMPLETE_TIMEOUT);
 	if (ret) {
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 2/6] phy: qcom-qusb2: Fix crash if nvmem cell not specified

Driver currently crashes due to NULL pointer deference
while updating PHY tune register if nvmem cell is NULL.
Since, fused value for Tune1/2 register is optional,
we'd rather bail out.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qusb2.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
index 94afeac..40fdef8 100644
--- a/drivers/phy/qualcomm/phy-qcom-qusb2.c
+++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
@@ -315,6 +315,10 @@ static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy)
 	const struct qusb2_phy_cfg *cfg = qphy->cfg;
 	u8 *val;
 
+	/* efuse register is optional */
+	if (!qphy->cell)
+		return;
+
 	/*
 	 * Read efuse register having TUNE2/1 parameter's high nibble.
 	 * If efuse register shows value as 0x0, or if we fail to find
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 2/6] phy: qcom-qusb2: Fix crash if nvmem cell not specified

[Manu Gautam]

Driver currently crashes due to NULL pointer deference
while updating PHY tune register if nvmem cell is NULL.
Since, fused value for Tune1/2 register is optional,
we'd rather bail out.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qusb2.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
index 94afeac..40fdef8 100644
--- a/drivers/phy/qualcomm/phy-qcom-qusb2.c
+++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
@@ -315,6 +315,10 @@ static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy)
 	const struct qusb2_phy_cfg *cfg = qphy->cfg;
 	u8 *val;
 
+	/* efuse register is optional */
+	if (!qphy->cell)
+		return;
+
 	/*
 	 * Read efuse register having TUNE2/1 parameter's high nibble.
 	 * If efuse register shows value as 0x0, or if we fail to find
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 3/6] dt-bindings: phy-qcom-qmp: Update bindings for sdm845

[Manu Gautam]

Update compatible strings for USB3 PHYs on SDM845.
One is QMPv3 DisplayPort-USB combo PHY and other one
is USB UNI PHY which is single lane USB3 PHY without
DP capability.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
index dcf1b8f..cef8765 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
+++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
@@ -9,7 +9,9 @@ Required properties:
 	       "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074
 	       "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
 	       "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996,
-	       "qcom,qmp-v3-usb3-phy" for USB3 QMP V3 phy.
+	       "qcom,qmp-v3-usb3-phy" for USB3 QMP V3 phy,
+	       "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845,
+	       "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845.
 
  - reg: offset and length of register set for PHY's common serdes block.
 
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 3/6] dt-bindings: phy-qcom-qmp: Update bindings for sdm845

[Manu Gautam]

Update compatible strings for USB3 PHYs on SDM845.
One is QMPv3 DisplayPort-USB combo PHY and other one
is USB UNI PHY which is single lane USB3 PHY without
DP capability.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
index dcf1b8f..cef8765 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
+++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
@@ -9,7 +9,9 @@ Required properties:
 	       "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074
 	       "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
 	       "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996,
-	       "qcom,qmp-v3-usb3-phy" for USB3 QMP V3 phy.
+	       "qcom,qmp-v3-usb3-phy" for USB3 QMP V3 phy,
+	       "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845,
+	       "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845.
 
  - reg: offset and length of register set for PHY's common serdes block.
 
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 4/6] phy: qcom-qmp: Add QMP V3 USB3 UNI PHY support for sdm845

[Manu Gautam]

QMP V3 UNI PHY is a single lane USB3 PHY without support
for DisplayPort (DP).
Main difference from DP combo QMPv3 PHY is that UNI PHY
doesn't have dual RX/TX lanes and no separate DP_COM
block for configuration related to type-c or DP.
While at it, fix has_pwrdn_delay attribute for USB-DP
PHY configuration.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 148 ++++++++++++++++++++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h |   5 ++
 2 files changed, 153 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 73aa282..689951d 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -490,6 +490,118 @@ enum qphy_reg_layout {
 	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
 };
 
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xc9),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x15),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_CFG, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER1, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER2, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER2, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE1, 0x85),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_HIGHZ_DRVR_EN, 0x10),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0xc6),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x06),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_VGA_CAL_CNTRL2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_MODE_00, 0x50),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x75),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_pcs_tbl[] = {
+	/* FLL settings */
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL2, 0x83),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_L, 0x09),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_H_TOL, 0xa2),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_MAN_CODE, 0x40),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL1, 0x02),
+
+	/* Lock Det settings */
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG1, 0xd1),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG2, 0x1f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG3, 0x47),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_POWER_STATE_CONFIG2, 0x1b),
+
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0xba),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V0, 0x9f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V1, 0x9f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V2, 0xb5),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V3, 0x4c),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V4, 0x64),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_LS, 0x6a),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V0, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V1, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V2, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V3, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3, 0x1d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V4, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_LS, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS, 0x0d),
+
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RATE_SLEW_CNTRL, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TSYNC_RSYNC_TIME, 0x44),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L, 0x40),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME, 0x75),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK, 0x86),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
+
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG1, 0x21),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG2, 0x60),
+};
+
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -766,6 +878,7 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
 	.pwrdn_ctrl		= SW_PWRDN,
 	.mask_pcs_ready		= PHYSTATUS,
 
+	.has_pwrdn_delay	= true,
 	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
 	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
 
@@ -774,6 +887,35 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
 	.rx_b_lane_offset	= 0x400,
 };
 
+static const struct qmp_phy_cfg qmp_v3_usb3_uniphy_cfg = {
+	.type			= PHY_TYPE_USB3,
+	.nlanes			= 1,
+
+	.serdes_tbl		= qmp_v3_usb3_uniphy_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_uniphy_serdes_tbl),
+	.tx_tbl			= qmp_v3_usb3_uniphy_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_uniphy_tx_tbl),
+	.rx_tbl			= qmp_v3_usb3_uniphy_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_uniphy_rx_tbl),
+	.pcs_tbl		= qmp_v3_usb3_uniphy_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_uniphy_pcs_tbl),
+	.clk_list		= qmp_v3_phy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v3_phy_clk_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= msm8996_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(msm8996_phy_vreg_l),
+	.regs			= qmp_v3_usb3phy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN,
+	.mask_pcs_ready		= PHYSTATUS,
+
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
+	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
+};
+
 static void qcom_qmp_phy_configure(void __iomem *base,
 				   const unsigned int *regs,
 				   const struct qmp_phy_init_tbl tbl[],
@@ -1401,6 +1543,12 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
 	}, {
 		.compatible = "qcom,qmp-v3-usb3-phy",
 		.data = &qmp_v3_usb3phy_cfg,
+	}, {
+		.compatible = "qcom,sdm845-qmp-usb3-phy",
+		.data = &qmp_v3_usb3phy_cfg,
+	}, {
+		.compatible = "qcom,sdm845-qmp-usb3-uni-phy",
+		.data = &qmp_v3_usb3_uniphy_cfg,
 	},
 	{ },
 };
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index d1c6905..5d78d43 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -214,6 +214,8 @@
 #define QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN		0x030
 #define QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE	0x034
 #define QSERDES_V3_RX_RX_TERM_BW			0x07c
+#define QSERDES_V3_RX_VGA_CAL_CNTRL1			0x0bc
+#define QSERDES_V3_RX_VGA_CAL_CNTRL2			0x0c0
 #define QSERDES_V3_RX_RX_EQ_GAIN2_LSB			0x0c8
 #define QSERDES_V3_RX_RX_EQ_GAIN2_MSB			0x0cc
 #define QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2		0x0d4
@@ -227,6 +229,7 @@
 #define QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL		0x10c
 #define QSERDES_V3_RX_RX_BAND				0x110
 #define QSERDES_V3_RX_RX_INTERFACE_MODE			0x11c
+#define QSERDES_V3_RX_RX_MODE_00			0x164
 
 /* Only for QMP V3 PHY - PCS registers */
 #define QPHY_V3_PCS_POWER_DOWN_CONTROL			0x004
@@ -273,6 +276,8 @@
 #define QPHY_V3_PCS_FLL_CNT_VAL_H_TOL			0x0d0
 #define QPHY_V3_PCS_FLL_MAN_CODE			0x0d4
 #define QPHY_V3_PCS_RX_SIGDET_LVL			0x1d8
+#define QPHY_V3_PCS_REFGEN_REQ_CONFIG1			0x20c
+#define QPHY_V3_PCS_REFGEN_REQ_CONFIG2			0x210
 
 /* Only for QMP V3 PHY - PCS_MISC registers */
 #define QPHY_V3_PCS_MISC_CLAMP_ENABLE			0x0c
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 4/6] phy: qcom-qmp: Add QMP V3 USB3 UNI PHY support for sdm845

[Manu Gautam]

QMP V3 UNI PHY is a single lane USB3 PHY without support
for DisplayPort (DP).
Main difference from DP combo QMPv3 PHY is that UNI PHY
doesn't have dual RX/TX lanes and no separate DP_COM
block for configuration related to type-c or DP.
While at it, fix has_pwrdn_delay attribute for USB-DP
PHY configuration.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 148 ++++++++++++++++++++++++++++++++++++
 drivers/phy/qualcomm/phy-qcom-qmp.h |   5 ++
 2 files changed, 153 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 73aa282..689951d 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -490,6 +490,118 @@ enum qphy_reg_layout {
 	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
 };
 
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xc9),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x15),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_CFG, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER1, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER2, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER2, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE1, 0x85),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_HIGHZ_DRVR_EN, 0x10),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0xc6),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x06),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_VGA_CAL_CNTRL2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_MODE_00, 0x50),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x75),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_usb3_uniphy_pcs_tbl[] = {
+	/* FLL settings */
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL2, 0x83),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_L, 0x09),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_H_TOL, 0xa2),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_MAN_CODE, 0x40),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL1, 0x02),
+
+	/* Lock Det settings */
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG1, 0xd1),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG2, 0x1f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG3, 0x47),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_POWER_STATE_CONFIG2, 0x1b),
+
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0xba),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V0, 0x9f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V1, 0x9f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V2, 0xb5),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V3, 0x4c),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V4, 0x64),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_LS, 0x6a),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V0, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V1, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V2, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V3, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3, 0x1d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V4, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_LS, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS, 0x0d),
+
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RATE_SLEW_CNTRL, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TSYNC_RSYNC_TIME, 0x44),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L, 0x40),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME, 0x75),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK, 0x86),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
+
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG1, 0x21),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG2, 0x60),
+};
+
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -766,6 +878,7 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
 	.pwrdn_ctrl		= SW_PWRDN,
 	.mask_pcs_ready		= PHYSTATUS,
 
+	.has_pwrdn_delay	= true,
 	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
 	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
 
@@ -774,6 +887,35 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
 	.rx_b_lane_offset	= 0x400,
 };
 
+static const struct qmp_phy_cfg qmp_v3_usb3_uniphy_cfg = {
+	.type			= PHY_TYPE_USB3,
+	.nlanes			= 1,
+
+	.serdes_tbl		= qmp_v3_usb3_uniphy_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_uniphy_serdes_tbl),
+	.tx_tbl			= qmp_v3_usb3_uniphy_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_uniphy_tx_tbl),
+	.rx_tbl			= qmp_v3_usb3_uniphy_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_uniphy_rx_tbl),
+	.pcs_tbl		= qmp_v3_usb3_uniphy_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(qmp_v3_usb3_uniphy_pcs_tbl),
+	.clk_list		= qmp_v3_phy_clk_l,
+	.num_clks		= ARRAY_SIZE(qmp_v3_phy_clk_l),
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= msm8996_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(msm8996_phy_vreg_l),
+	.regs			= qmp_v3_usb3phy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN,
+	.mask_pcs_ready		= PHYSTATUS,
+
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= POWER_DOWN_DELAY_US_MIN,
+	.pwrdn_delay_max	= POWER_DOWN_DELAY_US_MAX,
+};
+
 static void qcom_qmp_phy_configure(void __iomem *base,
 				   const unsigned int *regs,
 				   const struct qmp_phy_init_tbl tbl[],
@@ -1401,6 +1543,12 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
 	}, {
 		.compatible = "qcom,qmp-v3-usb3-phy",
 		.data = &qmp_v3_usb3phy_cfg,
+	}, {
+		.compatible = "qcom,sdm845-qmp-usb3-phy",
+		.data = &qmp_v3_usb3phy_cfg,
+	}, {
+		.compatible = "qcom,sdm845-qmp-usb3-uni-phy",
+		.data = &qmp_v3_usb3_uniphy_cfg,
 	},
 	{ },
 };
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index d1c6905..5d78d43 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -214,6 +214,8 @@
 #define QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN		0x030
 #define QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE	0x034
 #define QSERDES_V3_RX_RX_TERM_BW			0x07c
+#define QSERDES_V3_RX_VGA_CAL_CNTRL1			0x0bc
+#define QSERDES_V3_RX_VGA_CAL_CNTRL2			0x0c0
 #define QSERDES_V3_RX_RX_EQ_GAIN2_LSB			0x0c8
 #define QSERDES_V3_RX_RX_EQ_GAIN2_MSB			0x0cc
 #define QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2		0x0d4
@@ -227,6 +229,7 @@
 #define QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL		0x10c
 #define QSERDES_V3_RX_RX_BAND				0x110
 #define QSERDES_V3_RX_RX_INTERFACE_MODE			0x11c
+#define QSERDES_V3_RX_RX_MODE_00			0x164
 
 /* Only for QMP V3 PHY - PCS registers */
 #define QPHY_V3_PCS_POWER_DOWN_CONTROL			0x004
@@ -273,6 +276,8 @@
 #define QPHY_V3_PCS_FLL_CNT_VAL_H_TOL			0x0d0
 #define QPHY_V3_PCS_FLL_MAN_CODE			0x0d4
 #define QPHY_V3_PCS_RX_SIGDET_LVL			0x1d8
+#define QPHY_V3_PCS_REFGEN_REQ_CONFIG1			0x20c
+#define QPHY_V3_PCS_REFGEN_REQ_CONFIG2			0x210
 
 /* Only for QMP V3 PHY - PCS_MISC registers */
 #define QPHY_V3_PCS_MISC_CLAMP_ENABLE			0x0c
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 5/6] dt-bindings: phy-qcom-usb2: Update bindings for sdm845

[Manu Gautam]

Update compatible strings for USB2 PHYs on sdm845.
There are two QUSB2 PHYs present on sdm845. Few PHY registers
programming is different for these PHYs related to electrical
parameters, otherwise both are same.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
index 42c9742..20deaeb 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
@@ -6,7 +6,9 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
 Required properties:
  - compatible: compatible list, contains
 	       "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
-	       "qcom,qusb2-v2-phy" for QUSB2 V2 PHY.
+	       "qcom,qusb2-v2-phy" for QUSB2 V2 PHY,
+	       "qcom,sdm845-1-qusb2-phy" for primary PHY on sdm845,
+	       "qcom,sdm845-2-qusb2-phy" for secondary PHY on sdm845.
 
  - reg: offset and length of the PHY register set.
  - #phy-cells: must be 0.
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 5/6] dt-bindings: phy-qcom-usb2: Update bindings for sdm845

[Manu Gautam]

Update compatible strings for USB2 PHYs on sdm845.
There are two QUSB2 PHYs present on sdm845. Few PHY registers
programming is different for these PHYs related to electrical
parameters, otherwise both are same.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
index 42c9742..20deaeb 100644
--- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
@@ -6,7 +6,9 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
 Required properties:
  - compatible: compatible list, contains
 	       "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
-	       "qcom,qusb2-v2-phy" for QUSB2 V2 PHY.
+	       "qcom,qusb2-v2-phy" for QUSB2 V2 PHY,
+	       "qcom,sdm845-1-qusb2-phy" for primary PHY on sdm845,
+	       "qcom,sdm845-2-qusb2-phy" for secondary PHY on sdm845.
 
  - reg: offset and length of the PHY register set.
  - #phy-cells: must be 0.
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 6/6] phy: qcom-qusb2: Add QUSB2 PHYs support for sdm845

[Manu Gautam]

There are two QUSB2 PHYs present on sdm845. Update PHY
registers programming for both the PHYs related to
electrical parameters to improve eye diagram.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qusb2.c | 39 +++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
index 40fdef8..1a608a9 100644
--- a/drivers/phy/qualcomm/phy-qcom-qusb2.c
+++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
@@ -174,6 +174,27 @@ enum qusb2phy_reg_layout {
 	QUSB2_PHY_INIT_CFG(QUSB2PHY_CHG_CTRL2, 0x0),
 };
 
+static const struct qusb2_phy_init_tbl sdm845_init_tbl_1[] = {
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x03),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_1, 0x40),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_2, 0x20),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PWR_CTRL2, 0x21),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL1, 0x8),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL2, 0x58),
+
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0x45),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x29),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0xca),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0x04),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE5, 0x03),
+
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_CHG_CTRL2, 0x0),
+};
+
 struct qusb2_phy_cfg {
 	const struct qusb2_phy_init_tbl *tbl;
 	/* number of entries in the table */
@@ -220,6 +241,18 @@ struct qusb2_phy_cfg {
 	.autoresume_en	  = BIT(0),
 };
 
+static const struct qusb2_phy_cfg sdm845_phy_cfg_1 = {
+	.tbl		= sdm845_init_tbl_1,
+	.tbl_num	= ARRAY_SIZE(sdm845_init_tbl_1),
+	.regs		= qusb2_v2_regs_layout,
+
+	.disable_ctrl	= (PWR_CTRL1_VREF_SUPPLY_TRIM | PWR_CTRL1_CLAMP_N_EN |
+			   POWER_DOWN),
+	.mask_core_ready = CORE_READY_STATUS,
+	.has_pll_override = true,
+	.autoresume_en	  = BIT(0),
+};
+
 static const char * const qusb2_phy_vreg_names[] = {
 	"vdda-pll", "vdda-phy-dpdm",
 };
@@ -649,6 +682,12 @@ static int qusb2_phy_exit(struct phy *phy)
 	}, {
 		.compatible	= "qcom,qusb2-v2-phy",
 		.data		= &qusb2_v2_phy_cfg,
+	}, {
+		.compatible	= "qcom,sdm845-1-qusb2-phy",
+		.data		= &sdm845_phy_cfg_1,
+	}, {
+		.compatible	= "qcom,sdm845-2-qusb2-phy",
+		.data		= &qusb2_v2_phy_cfg,
 	},
 	{ },
 };
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH 6/6] phy: qcom-qusb2: Add QUSB2 PHYs support for sdm845

[Manu Gautam]

There are two QUSB2 PHYs present on sdm845. Update PHY
registers programming for both the PHYs related to
electrical parameters to improve eye diagram.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
 drivers/phy/qualcomm/phy-qcom-qusb2.c | 39 +++++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
index 40fdef8..1a608a9 100644
--- a/drivers/phy/qualcomm/phy-qcom-qusb2.c
+++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
@@ -174,6 +174,27 @@ enum qusb2phy_reg_layout {
 	QUSB2_PHY_INIT_CFG(QUSB2PHY_CHG_CTRL2, 0x0),
 };
 
+static const struct qusb2_phy_init_tbl sdm845_init_tbl_1[] = {
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x03),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_1, 0x40),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_2, 0x20),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PWR_CTRL2, 0x21),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL1, 0x8),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL2, 0x58),
+
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0x45),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x29),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0xca),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0x04),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE5, 0x03),
+
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_CHG_CTRL2, 0x0),
+};
+
 struct qusb2_phy_cfg {
 	const struct qusb2_phy_init_tbl *tbl;
 	/* number of entries in the table */
@@ -220,6 +241,18 @@ struct qusb2_phy_cfg {
 	.autoresume_en	  = BIT(0),
 };
 
+static const struct qusb2_phy_cfg sdm845_phy_cfg_1 = {
+	.tbl		= sdm845_init_tbl_1,
+	.tbl_num	= ARRAY_SIZE(sdm845_init_tbl_1),
+	.regs		= qusb2_v2_regs_layout,
+
+	.disable_ctrl	= (PWR_CTRL1_VREF_SUPPLY_TRIM | PWR_CTRL1_CLAMP_N_EN |
+			   POWER_DOWN),
+	.mask_core_ready = CORE_READY_STATUS,
+	.has_pll_override = true,
+	.autoresume_en	  = BIT(0),
+};
+
 static const char * const qusb2_phy_vreg_names[] = {
 	"vdda-pll", "vdda-phy-dpdm",
 };
@@ -649,6 +682,12 @@ static int qusb2_phy_exit(struct phy *phy)
 	}, {
 		.compatible	= "qcom,qusb2-v2-phy",
 		.data		= &qusb2_v2_phy_cfg,
+	}, {
+		.compatible	= "qcom,sdm845-1-qusb2-phy",
+		.data		= &sdm845_phy_cfg_1,
+	}, {
+		.compatible	= "qcom,sdm845-2-qusb2-phy",
+		.data		= &qusb2_v2_phy_cfg,
 	},
 	{ },
 };
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH 3/6] dt-bindings: phy-qcom-qmp: Update bindings for sdm845

[Rob Herring]

On Fri, Mar 16, 2018 at 03:14:56PM +0530, Manu Gautam wrote:
> Update compatible strings for USB3 PHYs on SDM845.
> One is QMPv3 DisplayPort-USB combo PHY and other one
> is USB UNI PHY which is single lane USB3 PHY without
> DP capability.
> 
> Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
> ---
>  Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt | 4 +++-
>  1 file changed, 3 insertions(+), 1 deletion(-)

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH 5/6] dt-bindings: phy-qcom-usb2: Update bindings for sdm845

[Rob Herring]

On Fri, Mar 16, 2018 at 03:14:58PM +0530, Manu Gautam wrote:
> Update compatible strings for USB2 PHYs on sdm845.
> There are two QUSB2 PHYs present on sdm845. Few PHY registers
> programming is different for these PHYs related to electrical
> parameters, otherwise both are same.

Register locations are different or tuning values are different? For the 
latter, is that something that could be DT properties?

> 
> Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
> ---
>  Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt | 4 +++-
>  1 file changed, 3 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
> index 42c9742..20deaeb 100644
> --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
> @@ -6,7 +6,9 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
>  Required properties:
>   - compatible: compatible list, contains
>  	       "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
> -	       "qcom,qusb2-v2-phy" for QUSB2 V2 PHY.
> +	       "qcom,qusb2-v2-phy" for QUSB2 V2 PHY,
> +	       "qcom,sdm845-1-qusb2-phy" for primary PHY on sdm845,
> +	       "qcom,sdm845-2-qusb2-phy" for secondary PHY on sdm845.
>  
>   - reg: offset and length of the PHY register set.
>   - #phy-cells: must be 0.
> -- 
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
> 

Re: [PATCH 5/6] dt-bindings: phy-qcom-usb2: Update bindings for sdm845

[Manu Gautam]

Hi,


On 3/18/2018 6:22 PM, Rob Herring wrote:
> On Fri, Mar 16, 2018 at 03:14:58PM +0530, Manu Gautam wrote:
>> Update compatible strings for USB2 PHYs on sdm845.
>> There are two QUSB2 PHYs present on sdm845. Few PHY registers
>> programming is different for these PHYs related to electrical
>> parameters, otherwise both are same.
> Register locations are different or tuning values are different? For the 
> latter, is that something that could be DT properties?

There are only register values changes. Corresponding driver change:
https://patchwork.kernel.org/patch/10286803/


-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH 4/6] phy: qcom-qmp: Add QMP V3 USB3 UNI PHY support for sdm845

[Evan Green]

Hi Manu,

On Fri, Mar 16, 2018 at 2:46 AM Manu Gautam <mgautam@codeaurora.org> wrote:

> QMP V3 UNI PHY is a single lane USB3 PHY without support
> for DisplayPort (DP).
> Main difference from DP combo QMPv3 PHY is that UNI PHY
> doesn't have dual RX/TX lanes and no separate DP_COM
> block for configuration related to type-c or DP.
> While at it, fix has_pwrdn_delay attribute for USB-DP
> PHY configuration.

> Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp.c | 148
++++++++++++++++++++++++++++++++++++
>   drivers/phy/qualcomm/phy-qcom-qmp.h |   5 ++
>   2 files changed, 153 insertions(+)

...
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h
b/drivers/phy/qualcomm/phy-qcom-qmp.h
> index d1c6905..5d78d43 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.h
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
> @@ -214,6 +214,8 @@
>   #define QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN            0x030
>   #define QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE    0x034
>   #define QSERDES_V3_RX_RX_TERM_BW                       0x07c
> +#define QSERDES_V3_RX_VGA_CAL_CNTRL1                   0x0bc

I noticed you add this definition, but never use it. Are you missing a
QMP_PHY_INIT_CFG line for this register in qmp_v3_usb3_uniphy_rx_tbl[], or
is that register "don't care"? It looks important, and while its default
value out of reset might be valid, you never know what nutty value boot
firmware might set it to.

> +#define QSERDES_V3_RX_VGA_CAL_CNTRL2                   0x0c0
>   #define QSERDES_V3_RX_RX_EQ_GAIN2_LSB                  0x0c8
>   #define QSERDES_V3_RX_RX_EQ_GAIN2_MSB                  0x0cc
>   #define QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2            0x0d4
> @@ -227,6 +229,7 @@
>   #define QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL            0x10c
>   #define QSERDES_V3_RX_RX_BAND                          0x110
>   #define QSERDES_V3_RX_RX_INTERFACE_MODE                        0x11c
> +#define QSERDES_V3_RX_RX_MODE_00                       0x164

>   /* Only for QMP V3 PHY - PCS registers */
>   #define QPHY_V3_PCS_POWER_DOWN_CONTROL                 0x004
> @@ -273,6 +276,8 @@
>   #define QPHY_V3_PCS_FLL_CNT_VAL_H_TOL                  0x0d0
>   #define QPHY_V3_PCS_FLL_MAN_CODE                       0x0d4
>   #define QPHY_V3_PCS_RX_SIGDET_LVL                      0x1d8
> +#define QPHY_V3_PCS_REFGEN_REQ_CONFIG1                 0x20c
> +#define QPHY_V3_PCS_REFGEN_REQ_CONFIG2                 0x210

>   /* Only for QMP V3 PHY - PCS_MISC registers */
>   #define QPHY_V3_PCS_MISC_CLAMP_ENABLE                  0x0c
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project

> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm"
in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 4/6] phy: qcom-qmp: Add QMP V3 USB3 UNI PHY support for sdm845

[Manu Gautam]

Hi,


On 3/19/2018 11:21 PM, Evan Green wrote:
> Hi Manu,
>
> On Fri, Mar 16, 2018 at 2:46 AM Manu Gautam <mgautam@codeaurora.org> wrote:
[snip]
>> index d1c6905..5d78d43 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-qmp.h
>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
>> @@ -214,6 +214,8 @@
>>   #define QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN            0x030
>>   #define QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE    0x034
>>   #define QSERDES_V3_RX_RX_TERM_BW                       0x07c
>> +#define QSERDES_V3_RX_VGA_CAL_CNTRL1                   0x0bc
> I noticed you add this definition, but never use it. Are you missing a
> QMP_PHY_INIT_CFG line for this register in qmp_v3_usb3_uniphy_rx_tbl[], or
> is that register "don't care"? It looks important, and while its default
> value out of reset might be valid, you never know what nutty value boot
> firmware might set it to.
>

Yes POR value of this register is valid for this soc.
QMP driver resets (asserts and de-asserts reset_control) in probe. So, that should
ensure that PHY registers are indeed set to POR value. Left the definition there
if different setting needed to be done for a different variant of h/w in future.

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH 2/6] phy: qcom-qusb2: Fix crash if nvmem cell not specified

[Vivek Gautam]

Hi Manu,


On 3/16/2018 3:14 PM, Manu Gautam wrote:
> Driver currently crashes due to NULL pointer deference
> while updating PHY tune register if nvmem cell is NULL.
> Since, fused value for Tune1/2 register is optional,
> we'd rather bail out.

fixes: ("ca04d9d3e1b1 phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom 
chips") ?
and please CC to stable as well - ver 4.14.

With that,
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>

Thanks
Vivek
>
> Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qusb2.c | 4 ++++
>   1 file changed, 4 insertions(+)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
> index 94afeac..40fdef8 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qusb2.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
> @@ -315,6 +315,10 @@ static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy)
>   	const struct qusb2_phy_cfg *cfg = qphy->cfg;
>   	u8 *val;
>   
> +	/* efuse register is optional */
> +	if (!qphy->cell)
> +		return;
> +
>   	/*
>   	 * Read efuse register having TUNE2/1 parameter's high nibble.
>   	 * If efuse register shows value as 0x0, or if we fail to find

Re: [PATCH 5/6] dt-bindings: phy-qcom-usb2: Update bindings for sdm845

[Vivek Gautam]

Hi Manu,


On 3/16/2018 3:14 PM, Manu Gautam wrote:
> Update compatible strings for USB2 PHYs on sdm845.
> There are two QUSB2 PHYs present on sdm845. Few PHY registers
> programming is different for these PHYs related to electrical
> parameters, otherwise both are same.
>
> Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
> ---
>   Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt | 4 +++-
>   1 file changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
> index 42c9742..20deaeb 100644
> --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
> @@ -6,7 +6,9 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
>   Required properties:
>    - compatible: compatible list, contains
>   	       "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
> -	       "qcom,qusb2-v2-phy" for QUSB2 V2 PHY.
> +	       "qcom,qusb2-v2-phy" for QUSB2 V2 PHY,
> +	       "qcom,sdm845-1-qusb2-phy" for primary PHY on sdm845,
> +	       "qcom,sdm845-2-qusb2-phy" for secondary PHY on sdm845.

Thanks for the patch.

"qcom,sdm845-1/2-qusb2-phy" gives an impression that it is different versions of SoC,
and not like two numbers of phy.
May be - "qcom,sdm845-qusb2-phy-1/2"

Regards
Vivek
  

>   
>    - reg: offset and length of the PHY register set.
>    - #phy-cells: must be 0.

Re: [PATCH 5/6] dt-bindings: phy-qcom-usb2: Update bindings for sdm845

[Manu Gautam]

Hi,


On 3/20/2018 3:53 PM, Vivek Gautam wrote:
> Hi Manu,
>
>
> On 3/16/2018 3:14 PM, Manu Gautam wrote:
>> Update compatible strings for USB2 PHYs on sdm845.
>> There are two QUSB2 PHYs present on sdm845. Few PHY registers
>> programming is different for these PHYs related to electrical
>> parameters, otherwise both are same.
>>
>> Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
>> ---
>>   Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt | 4 +++-
>>   1 file changed, 3 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
>> index 42c9742..20deaeb 100644
>> --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
>> +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
>> @@ -6,7 +6,9 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
>>   Required properties:
>>    - compatible: compatible list, contains
>>              "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
>> -           "qcom,qusb2-v2-phy" for QUSB2 V2 PHY.
>> +           "qcom,qusb2-v2-phy" for QUSB2 V2 PHY,
>> +           "qcom,sdm845-1-qusb2-phy" for primary PHY on sdm845,
>> +           "qcom,sdm845-2-qusb2-phy" for secondary PHY on sdm845.
>
> Thanks for the patch.
>
> "qcom,sdm845-1/2-qusb2-phy" gives an impression that it is different versions of SoC,
> and not like two numbers of phy.
> May be - "qcom,sdm845-qusb2-phy-1/2"

I agree with that. Will update.

>
> Regards
> Vivek
>  
>
>>      - reg: offset and length of the PHY register set.
>>    - #phy-cells: must be 0.
>

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH 4/6] phy: qcom-qmp: Add QMP V3 USB3 UNI PHY support for sdm845

[Evan Green]

On Tue, Mar 20, 2018 at 12:00 AM Manu Gautam <mgautam@codeaurora.org> wrote:

> Hi,


> On 3/19/2018 11:21 PM, Evan Green wrote:
> > Hi Manu,
> >
> > On Fri, Mar 16, 2018 at 2:46 AM Manu Gautam <mgautam@codeaurora.org>
wrote:
> [snip]
> >> index d1c6905..5d78d43 100644
> >> --- a/drivers/phy/qualcomm/phy-qcom-qmp.h
> >> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
> >> @@ -214,6 +214,8 @@
> >>   #define QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN            0x030
> >>   #define QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE    0x034
> >>   #define QSERDES_V3_RX_RX_TERM_BW                       0x07c
> >> +#define QSERDES_V3_RX_VGA_CAL_CNTRL1                   0x0bc
> > I noticed you add this definition, but never use it. Are you missing a
> > QMP_PHY_INIT_CFG line for this register in qmp_v3_usb3_uniphy_rx_tbl[],
or
> > is that register "don't care"? It looks important, and while its default
> > value out of reset might be valid, you never know what nutty value boot
> > firmware might set it to.
> >

> Yes POR value of this register is valid for this soc.
> QMP driver resets (asserts and de-asserts reset_control) in probe. So,
that should
> ensure that PHY registers are indeed set to POR value. Left the
definition there
> if different setting needed to be done for a different variant of h/w in
future.

Sounds good. Thanks, Manu.

Reviewed-by: Evan Green <evgreen@chromium.org>