[U-Boot] [PATCH 00/10] rockchip: enable board_debug_uart_init for all soc

[U-Boot] [PATCH 00/10] rockchip: enable board_debug_uart_init for all soc

[Kever Yang]

ALl rockchip soc use DEBUG UART, and need init the uart iomux
in board_debug_uart_init().
Move the board_debug_uart_init() into soc file so that we can
make all soc config in soc file and share a common board file
later for all rockchip SoCs.



Kever Yang (10):
  rockchip: enable DEBUG_UART_BOARD_INIT by default
  rockchip; kylin-rk3036: enabl DEBUG UART
  rockchip: rk3036: add board_debug_uart_init()
  rockchip: rk3188: add board_debug_uart_init()
  rockchip: rk322x: move board_debug_uart_init() to rk322x.c
  rockchip: rk3288: use grf structure to access soc_con2
  rockchip: rk3288: add board_debug_uart_init()
  rockchip: rk3368: move board_debug_uart_init() to rk3368.c
  rockchip: rk3399: use grf structure to access reg
  rockchip: rk3399: add board_debug_uart_init()

 arch/arm/Kconfig                          |  2 ++
 arch/arm/mach-rockchip/Kconfig            |  3 ---
 arch/arm/mach-rockchip/rk3036-board-spl.c | 19 +------------
 arch/arm/mach-rockchip/rk3036/Makefile    |  1 +
 arch/arm/mach-rockchip/rk3036/rk3036.c    | 40 +++++++++++++++++++++++++++
 arch/arm/mach-rockchip/rk3188-board-spl.c | 12 +--------
 arch/arm/mach-rockchip/rk3188/Makefile    |  1 +
 arch/arm/mach-rockchip/rk3188/rk3188.c    | 37 +++++++++++++++++++++++++
 arch/arm/mach-rockchip/rk322x-board-spl.c | 43 ++---------------------------
 arch/arm/mach-rockchip/rk322x-board.c     | 31 +--------------------
 arch/arm/mach-rockchip/rk322x/Makefile    |  2 +-
 arch/arm/mach-rockchip/rk322x/rk322x.c    | 45 +++++++++++++++++++++++++++++++
 arch/arm/mach-rockchip/rk3288-board-spl.c | 11 ++------
 arch/arm/mach-rockchip/rk3288-board-tpl.c | 13 ++-------
 arch/arm/mach-rockchip/rk3288/rk3288.c    | 19 +++++++++++--
 arch/arm/mach-rockchip/rk3368-board-spl.c |  5 ----
 arch/arm/mach-rockchip/rk3368-board-tpl.c | 33 +----------------------
 arch/arm/mach-rockchip/rk3368/rk3368.c    | 31 +++++++++++++++++++++
 arch/arm/mach-rockchip/rk3399-board-spl.c | 31 +--------------------
 arch/arm/mach-rockchip/rk3399/rk3399.c    | 34 ++++++++++++++++++++++-
 configs/kylin-rk3036_defconfig            |  4 +++
 21 files changed, 223 insertions(+), 194 deletions(-)
 create mode 100644 arch/arm/mach-rockchip/rk3036/rk3036.c
 create mode 100644 arch/arm/mach-rockchip/rk3188/rk3188.c
 create mode 100644 arch/arm/mach-rockchip/rk322x/rk322x.c

-- 
1.9.1

[U-Boot] [PATCH 01/10] rockchip: enable DEBUG_UART_BOARD_INIT by default

[Kever Yang]

All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
UART IOMUX, enable it by default.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

 arch/arm/Kconfig               | 2 ++
 arch/arm/mach-rockchip/Kconfig | 3 ---
 2 files changed, 2 insertions(+), 3 deletions(-)

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index a90f870..97e4a93 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1191,6 +1191,7 @@ config ARCH_ROCKCHIP
 	select DM_PWM
 	select DM_REGULATOR
 	select ENABLE_ARM_SOC_BOOT0_HOOK
+	select DEBUG_UART_BOARD_INIT
 	imply CMD_FASTBOOT
 	imply FASTBOOT
 	imply FAT_WRITE
@@ -1201,6 +1202,7 @@ config ARCH_ROCKCHIP
 	imply SARADC_ROCKCHIP
 	imply SYS_NS16550
 
+
 config TARGET_THUNDERX_88XX
 	bool "Support ThunderX 88xx"
 	select ARM64
diff --git a/arch/arm/mach-rockchip/Kconfig b/arch/arm/mach-rockchip/Kconfig
index 41f529c..ccb9fa6 100644
--- a/arch/arm/mach-rockchip/Kconfig
+++ b/arch/arm/mach-rockchip/Kconfig
@@ -50,7 +50,6 @@ config ROCKCHIP_RK322X
 	select SUPPORT_SPL
 	select SPL
 	select ROCKCHIP_BROM_HELPER
-	select DEBUG_UART_BOARD_INIT
 	help
 	  The Rockchip RK3229 is a ARM-based SoC with a dual-core Cortex-A7
 	  including NEON and GPU, Mali-400 graphics, several DDR3 options
@@ -102,7 +101,6 @@ config ROCKCHIP_RK3368
 	imply SPL_SEPARATE_BSS
 	imply SPL_SERIAL_SUPPORT
 	imply TPL_SERIAL_SUPPORT
-	select DEBUG_UART_BOARD_INIT
 	help
 	  The Rockchip RK3368 is a ARM-based SoC with a octa-core (organised
 	  into a big and little cluster with 4 cores each) Cortex-A53 including
@@ -138,7 +136,6 @@ config ROCKCHIP_RK3399
 	select SPL_SEPARATE_BSS
 	select SPL_SERIAL_SUPPORT
 	select SPL_DRIVERS_MISC_SUPPORT
-	select DEBUG_UART_BOARD_INIT
 	select BOARD_LATE_INIT
 	select ROCKCHIP_BROM_HELPER
 	help
-- 
1.9.1

[U-Boot] [PATCH 02/10] rockchip; kylin-rk3036: enabl DEBUG UART

[Kever Yang]

Enable debug uart for kylin board in defconfig.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

 configs/kylin-rk3036_defconfig | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/configs/kylin-rk3036_defconfig b/configs/kylin-rk3036_defconfig
index c7bd73f..6ff187e 100644
--- a/configs/kylin-rk3036_defconfig
+++ b/configs/kylin-rk3036_defconfig
@@ -8,6 +8,7 @@ CONFIG_ROCKCHIP_RK3036=y
 CONFIG_TARGET_KYLIN_RK3036=y
 CONFIG_SPL_STACK_R_ADDR=0x80000
 CONFIG_DEFAULT_DEVICE_TREE="rk3036-sdk"
+CONFIG_DEBUG_UART=y
 CONFIG_SPL_SYS_MALLOC_F_LEN=0x0
 # CONFIG_ANDROID_BOOT_IMAGE is not set
 # CONFIG_DISPLAY_CPUINFO is not set
@@ -40,6 +41,9 @@ CONFIG_PINCTRL=y
 CONFIG_PINCTRL_ROCKCHIP_RK3036=y
 CONFIG_DM_REGULATOR_FIXED=y
 # CONFIG_SPL_DM_SERIAL is not set
+CONFIG_DEBUG_UART_BASE=0x20068000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_DEBUG_UART_SHIFT=2
 CONFIG_SYSRESET=y
 CONFIG_USB=y
 CONFIG_USB_DWC2=y
-- 
1.9.1

[U-Boot] [PATCH 03/10] rockchip: rk3036: add board_debug_uart_init()

[Kever Yang]

Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

 arch/arm/mach-rockchip/rk3036-board-spl.c | 19 +--------------
 arch/arm/mach-rockchip/rk3036/Makefile    |  1 +
 arch/arm/mach-rockchip/rk3036/rk3036.c    | 40 +++++++++++++++++++++++++++++++
 3 files changed, 42 insertions(+), 18 deletions(-)
 create mode 100644 arch/arm/mach-rockchip/rk3036/rk3036.c

diff --git a/arch/arm/mach-rockchip/rk3036-board-spl.c b/arch/arm/mach-rockchip/rk3036-board-spl.c
index 4b4016b..71124c8 100644
--- a/arch/arm/mach-rockchip/rk3036-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3036-board-spl.c
@@ -8,17 +8,11 @@
 #include <debug_uart.h>
 #include <asm/io.h>
 #include <asm/arch/bootrom.h>
-#include <asm/arch/grf_rk3036.h>
-#include <asm/arch/hardware.h>
 #include <asm/arch/sdram_rk3036.h>
 #include <asm/arch/uart.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#define GRF_BASE	0x20008000
-
-#define DEBUG_UART_BASE	0x20068000
-
 void rockchip_stimer_init(void)
 {
 	asm volatile("mcr p15, 0, %0, c14, c0, 0"
@@ -32,18 +26,7 @@ void rockchip_stimer_init(void)
 
 void board_init_f(ulong dummy)
 {
-#ifdef EARLY_DEBUG
-	struct rk3036_grf * const grf = (void *)GRF_BASE;
-	/*
-	 * NOTE: sd card and debug uart use same iomux in rk3036,
-	 * so if you enable uart,
-	 * you can not boot from sdcard
-	 */
-	rk_clrsetreg(&grf->gpio1c_iomux,
-		     GPIO1C3_MASK << GPIO1C3_SHIFT |
-		     GPIO1C2_MASK << GPIO1C2_SHIFT,
-		     GPIO1C3_UART2_SOUT << GPIO1C3_SHIFT |
-		     GPIO1C2_UART2_SIN << GPIO1C2_SHIFT);
+#ifdef CONFIG_DEBUG_UART
 	debug_uart_init();
 #endif
 
diff --git a/arch/arm/mach-rockchip/rk3036/Makefile b/arch/arm/mach-rockchip/rk3036/Makefile
index 20d28f7..299fc50 100644
--- a/arch/arm/mach-rockchip/rk3036/Makefile
+++ b/arch/arm/mach-rockchip/rk3036/Makefile
@@ -10,4 +10,5 @@ ifndef CONFIG_SPL_BUILD
 obj-y += syscon_rk3036.o
 endif
 
+obj-y += rk3036.o
 obj-y += sdram_rk3036.o
diff --git a/arch/arm/mach-rockchip/rk3036/rk3036.c b/arch/arm/mach-rockchip/rk3036/rk3036.c
new file mode 100644
index 0000000..5a486ab
--- /dev/null
+++ b/arch/arm/mach-rockchip/rk3036/rk3036.c
@@ -0,0 +1,40 @@
+/*
+ * (C) Copyright 2018 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+#include <asm/io.h>
+#include <asm/arch/grf_rk3036.h>
+#include <asm/arch/hardware.h>
+
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
+{
+#define GRF_BASE	0x20008000
+	struct rk3036_grf * const grf = (void *)GRF_BASE;
+	enum {
+		GPIO1C3_SHIFT		= 6,
+		GPIO1C3_MASK		= 3 << GPIO1C3_SHIFT,
+		GPIO1C3_GPIO		= 0,
+		GPIO1C3_MMC0_D1,
+		GPIO1C3_UART2_SOUT,
+
+		GPIO1C2_SHIFT		= 4,
+		GPIO1C2_MASK		= 3 << GPIO1C2_SHIFT,
+		GPIO1C2_GPIO		= 0,
+		GPIO1C2_MMC0_D0,
+		GPIO1C2_UART2_SIN,
+	};
+	/*
+	 * NOTE: sd card and debug uart use same iomux in rk3036,
+	 * so if you enable uart,
+	 * you can not boot from sdcard
+	 */
+	rk_clrsetreg(&grf->gpio1c_iomux,
+		     GPIO1C3_MASK << GPIO1C3_SHIFT |
+		     GPIO1C2_MASK << GPIO1C2_SHIFT,
+		     GPIO1C3_UART2_SOUT << GPIO1C3_SHIFT |
+		     GPIO1C2_UART2_SIN << GPIO1C2_SHIFT);
+}
+#endif
+
-- 
1.9.1

[U-Boot] [PATCH 04/10] rockchip: rk3188: add board_debug_uart_init()

[Kever Yang]

Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

 arch/arm/mach-rockchip/rk3188-board-spl.c | 12 +---------
 arch/arm/mach-rockchip/rk3188/Makefile    |  1 +
 arch/arm/mach-rockchip/rk3188/rk3188.c    | 37 +++++++++++++++++++++++++++++++
 3 files changed, 39 insertions(+), 11 deletions(-)
 create mode 100644 arch/arm/mach-rockchip/rk3188/rk3188.c

diff --git a/arch/arm/mach-rockchip/rk3188-board-spl.c b/arch/arm/mach-rockchip/rk3188-board-spl.c
index 3ccc4f1..56ff77b 100644
--- a/arch/arm/mach-rockchip/rk3188-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3188-board-spl.c
@@ -99,17 +99,7 @@ void board_init_f(ulong dummy)
 	int ret;
 
 	/* Example code showing how to enable the debug UART on RK3188 */
-#ifdef EARLY_UART
-#include <asm/arch/grf_rk3188.h>
-	/* Enable early UART on the RK3188 */
-#define GRF_BASE	0x20008000
-	struct rk3188_grf * const grf = (void *)GRF_BASE;
-
-	rk_clrsetreg(&grf->gpio1b_iomux,
-		     GPIO1B1_MASK << GPIO1B1_SHIFT |
-		     GPIO1B0_MASK << GPIO1B0_SHIFT,
-		     GPIO1B1_UART2_SOUT << GPIO1B1_SHIFT |
-		     GPIO1B0_UART2_SIN << GPIO1B0_SHIFT);
+#ifdef CONFIG_DEBUG_UART
 	/*
 	 * Debug UART can be used from here if required:
 	 *
diff --git a/arch/arm/mach-rockchip/rk3188/Makefile b/arch/arm/mach-rockchip/rk3188/Makefile
index 7fa0104..7dc123a 100644
--- a/arch/arm/mach-rockchip/rk3188/Makefile
+++ b/arch/arm/mach-rockchip/rk3188/Makefile
@@ -6,5 +6,6 @@
 
 ifndef CONFIG_TPL_BUILD
 obj-y += clk_rk3188.o
+obj-y += rk3188.o
 obj-y += syscon_rk3188.o
 endif
diff --git a/arch/arm/mach-rockchip/rk3188/rk3188.c b/arch/arm/mach-rockchip/rk3188/rk3188.c
new file mode 100644
index 0000000..f2adcc9
--- /dev/null
+++ b/arch/arm/mach-rockchip/rk3188/rk3188.c
@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2018 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/grf_rk3188.h>
+#include <asm/arch/hardware.h>
+
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
+{
+	/* Enable early UART on the RK3188 */
+#define GRF_BASE	0x20008000
+	struct rk3188_grf * const grf = (void *)GRF_BASE;
+	enum {
+		GPIO1B1_SHIFT		= 2,
+		GPIO1B1_MASK		= 3,
+		GPIO1B1_GPIO		= 0,
+		GPIO1B1_UART2_SOUT,
+		GPIO1B1_JTAG_TDO,
+
+		GPIO1B0_SHIFT		= 0,
+		GPIO1B0_MASK		= 3,
+		GPIO1B0_GPIO		= 0,
+		GPIO1B0_UART2_SIN,
+		GPIO1B0_JTAG_TDI,
+	};
+
+	rk_clrsetreg(&grf->gpio1b_iomux,
+		     GPIO1B1_MASK << GPIO1B1_SHIFT |
+		     GPIO1B0_MASK << GPIO1B0_SHIFT,
+		     GPIO1B1_UART2_SOUT << GPIO1B1_SHIFT |
+		     GPIO1B0_UART2_SIN << GPIO1B0_SHIFT);
+}
+#endif
-- 
1.9.1

[U-Boot] [PATCH 05/10] rockchip: rk322x: move board_debug_uart_init() to rk322x.c

[Kever Yang]

Move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file later for all rockchip SoCs.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

 arch/arm/mach-rockchip/rk322x-board-spl.c | 43 ++---------------------------
 arch/arm/mach-rockchip/rk322x-board.c     | 31 +--------------------
 arch/arm/mach-rockchip/rk322x/Makefile    |  2 +-
 arch/arm/mach-rockchip/rk322x/rk322x.c    | 45 +++++++++++++++++++++++++++++++
 4 files changed, 49 insertions(+), 72 deletions(-)
 create mode 100644 arch/arm/mach-rockchip/rk322x/rk322x.c

diff --git a/arch/arm/mach-rockchip/rk322x-board-spl.c b/arch/arm/mach-rockchip/rk322x-board-spl.c
index b5b178f..2b67e14 100644
--- a/arch/arm/mach-rockchip/rk322x-board-spl.c
+++ b/arch/arm/mach-rockchip/rk322x-board-spl.c
@@ -12,7 +12,6 @@
 #include <asm/io.h>
 #include <asm/arch/bootrom.h>
 #include <asm/arch/cru_rk322x.h>
-#include <asm/arch/grf_rk322x.h>
 #include <asm/arch/hardware.h>
 #include <asm/arch/uart.h>
 
@@ -22,45 +21,6 @@ u32 spl_boot_device(void)
 }
 DECLARE_GLOBAL_DATA_PTR;
 
-#define GRF_BASE	0x11000000
-#define SGRF_BASE	0x10140000
-
-#define DEBUG_UART_BASE	0x11030000
-
-void board_debug_uart_init(void)
-{
-	static struct rk322x_grf * const grf = (void *)GRF_BASE;
-	enum {
-		GPIO1B2_SHIFT		= 4,
-		GPIO1B2_MASK		= 3 << GPIO1B2_SHIFT,
-		GPIO1B2_GPIO            = 0,
-		GPIO1B2_UART1_SIN,
-		GPIO1B2_UART21_SIN,
-
-		GPIO1B1_SHIFT		= 2,
-		GPIO1B1_MASK		= 3 << GPIO1B1_SHIFT,
-		GPIO1B1_GPIO            = 0,
-		GPIO1B1_UART1_SOUT,
-		GPIO1B1_UART21_SOUT,
-	};
-	enum {
-		CON_IOMUX_UART2SEL_SHIFT= 8,
-		CON_IOMUX_UART2SEL_MASK	= 1 << CON_IOMUX_UART2SEL_SHIFT,
-		CON_IOMUX_UART2SEL_2	= 0,
-		CON_IOMUX_UART2SEL_21,
-	};
-
-	/* Enable early UART2 channel 1 on the RK322x */
-	rk_clrsetreg(&grf->gpio1b_iomux,
-		     GPIO1B1_MASK | GPIO1B2_MASK,
-		     GPIO1B2_UART21_SIN << GPIO1B2_SHIFT |
-		     GPIO1B1_UART21_SOUT << GPIO1B1_SHIFT);
-	/* Set channel C as UART2 input */
-	rk_clrsetreg(&grf->con_iomux,
-		     CON_IOMUX_UART2SEL_MASK,
-		     CON_IOMUX_UART2SEL_21 << CON_IOMUX_UART2SEL_SHIFT);
-}
-
 void rockchip_stimer_init(void)
 {
 	asm volatile("mcr p15, 0, %0, c14, c0, 0"
@@ -78,6 +38,7 @@ void board_init_f(ulong dummy)
 	struct udevice *dev;
 	int ret;
 
+#ifdef CONFIG_DEBUG_UART
 	/*
 	 * Debug UART can be used from here if required:
 	 *
@@ -88,7 +49,7 @@ void board_init_f(ulong dummy)
 	 */
 	debug_uart_init();
 	printascii("SPL Init");
-
+#endif
 	ret = spl_early_init();
 	if (ret) {
 		debug("spl_early_init() failed: %d\n", ret);
diff --git a/arch/arm/mach-rockchip/rk322x-board.c b/arch/arm/mach-rockchip/rk322x-board.c
index 6295b1a..43b0d11 100644
--- a/arch/arm/mach-rockchip/rk322x-board.c
+++ b/arch/arm/mach-rockchip/rk322x-board.c
@@ -30,37 +30,8 @@ int board_late_init(void)
 
 int board_init(void)
 {
-#include <asm/arch/grf_rk322x.h>
-	/* Enable early UART2 channel 1 on the RK322x */
 #define GRF_BASE	0x11000000
-	struct rk322x_grf * const grf = (void *)GRF_BASE;
-	enum {
-		GPIO1B2_SHIFT		= 4,
-		GPIO1B2_MASK		= 3 << GPIO1B2_SHIFT,
-		GPIO1B2_GPIO		= 0,
-		GPIO1B2_UART21_SIN,
-
-		GPIO1B1_SHIFT		= 2,
-		GPIO1B1_MASK		= 3 << GPIO1B1_SHIFT,
-		GPIO1B1_GPIO            = 0,
-		GPIO1B1_UART1_SOUT,
-		GPIO1B1_UART21_SOUT,
-	};
-	enum {
-		CON_IOMUX_UART2SEL_SHIFT= 8,
-		CON_IOMUX_UART2SEL_MASK	= 1 << CON_IOMUX_UART2SEL_SHIFT,
-		CON_IOMUX_UART2SEL_2	= 0,
-		CON_IOMUX_UART2SEL_21,
-	};
-
-	rk_clrsetreg(&grf->gpio1b_iomux,
-		     GPIO1B1_MASK | GPIO1B2_MASK,
-		     GPIO1B2_UART21_SIN << GPIO1B2_SHIFT |
-		     GPIO1B1_UART21_SOUT << GPIO1B1_SHIFT);
-	/* Set channel C as UART2 input */
-	rk_clrsetreg(&grf->con_iomux,
-		     CON_IOMUX_UART2SEL_MASK,
-		     CON_IOMUX_UART2SEL_21 << CON_IOMUX_UART2SEL_SHIFT);
+	static struct rk322x_grf * const grf = (void *)GRF_BASE;
 
 	/*
 	* The integrated macphy is enabled by default, disable it
diff --git a/arch/arm/mach-rockchip/rk322x/Makefile b/arch/arm/mach-rockchip/rk322x/Makefile
index ecb3e8d..89b0fed 100644
--- a/arch/arm/mach-rockchip/rk322x/Makefile
+++ b/arch/arm/mach-rockchip/rk322x/Makefile
@@ -4,6 +4,6 @@
 # SPDX-License-Identifier:     GPL-2.0+
 #
 
-
 obj-y += clk_rk322x.o
+obj-y += rk322x.o
 obj-y += syscon_rk322x.o
diff --git a/arch/arm/mach-rockchip/rk322x/rk322x.c b/arch/arm/mach-rockchip/rk322x/rk322x.c
new file mode 100644
index 0000000..945fcf3
--- /dev/null
+++ b/arch/arm/mach-rockchip/rk322x/rk322x.c
@@ -0,0 +1,45 @@
+/*
+ * (C) Copyright 2018 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+#include <asm/io.h>
+#include <asm/arch/grf_rk322x.h>
+#include <asm/arch/hardware.h>
+
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
+{
+#define GRF_BASE	0x11000000
+	static struct rk322x_grf * const grf = (void *)GRF_BASE;
+	enum {
+		GPIO1B2_SHIFT		= 4,
+		GPIO1B2_MASK		= 3 << GPIO1B2_SHIFT,
+		GPIO1B2_GPIO            = 0,
+		GPIO1B2_UART1_SIN,
+		GPIO1B2_UART21_SIN,
+
+		GPIO1B1_SHIFT		= 2,
+		GPIO1B1_MASK		= 3 << GPIO1B1_SHIFT,
+		GPIO1B1_GPIO            = 0,
+		GPIO1B1_UART1_SOUT,
+		GPIO1B1_UART21_SOUT,
+	};
+	enum {
+		CON_IOMUX_UART2SEL_SHIFT = 8,
+		CON_IOMUX_UART2SEL_MASK	= 1 << CON_IOMUX_UART2SEL_SHIFT,
+		CON_IOMUX_UART2SEL_2	= 0,
+		CON_IOMUX_UART2SEL_21,
+	};
+
+	/* Enable early UART2 channel 1 on the RK322x */
+	rk_clrsetreg(&grf->gpio1b_iomux,
+		     GPIO1B1_MASK | GPIO1B2_MASK,
+		     GPIO1B2_UART21_SIN << GPIO1B2_SHIFT |
+		     GPIO1B1_UART21_SOUT << GPIO1B1_SHIFT);
+	/* Set channel C as UART2 input */
+	rk_clrsetreg(&grf->con_iomux,
+		     CON_IOMUX_UART2SEL_MASK,
+		     CON_IOMUX_UART2SEL_21 << CON_IOMUX_UART2SEL_SHIFT);
+}
+#endif
-- 
1.9.1

[U-Boot] [PATCH 06/10] rockchip: rk3288: use grf structure to access soc_con2

[Kever Yang]

Prefer to use structure to access register if we can.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

 arch/arm/mach-rockchip/rk3288/rk3288.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-rockchip/rk3288/rk3288.c b/arch/arm/mach-rockchip/rk3288/rk3288.c
index acc3b79..8f5aaa1 100644
--- a/arch/arm/mach-rockchip/rk3288/rk3288.c
+++ b/arch/arm/mach-rockchip/rk3288/rk3288.c
@@ -5,15 +5,17 @@
  */
 #include <asm/io.h>
 #include <asm/arch/hardware.h>
+#include <asm/arch/grf_rk3288.h>
 
-#define GRF_SOC_CON2 0xff77024c
+#define GRF_BASE	0xff770000
 
 int arch_cpu_init(void)
 {
 	/* We do some SoC one time setting here. */
+	struct rk3288_grf * const grf = (void *)GRF_BASE;
 
 	/* Use rkpwm by default */
-	rk_setreg(GRF_SOC_CON2, 1 << 0);
+	rk_setreg(&grf->soc_con2, 1 << 0);
 
 	return 0;
 }
-- 
1.9.1

[U-Boot] [PATCH 07/10] rockchip: rk3288: add board_debug_uart_init()

[Kever Yang]

Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file for all rockchip SoCs later.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

 arch/arm/mach-rockchip/rk3288-board-spl.c | 11 ++---------
 arch/arm/mach-rockchip/rk3288-board-tpl.c | 13 ++-----------
 arch/arm/mach-rockchip/rk3288/rk3288.c    | 13 +++++++++++++
 3 files changed, 17 insertions(+), 20 deletions(-)

diff --git a/arch/arm/mach-rockchip/rk3288-board-spl.c b/arch/arm/mach-rockchip/rk3288-board-spl.c
index 8f22549..22b12a1 100644
--- a/arch/arm/mach-rockchip/rk3288-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3288-board-spl.c
@@ -160,15 +160,7 @@ void board_init_f(ulong dummy)
 	int ret;
 
 	/* Example code showing how to enable the debug UART on RK3288 */
-#include <asm/arch/grf_rk3288.h>
-	/* Enable early UART on the RK3288 */
-#define GRF_BASE	0xff770000
-	struct rk3288_grf * const grf = (void *)GRF_BASE;
-
-	rk_clrsetreg(&grf->gpio7ch_iomux, GPIO7C7_MASK << GPIO7C7_SHIFT |
-		     GPIO7C6_MASK << GPIO7C6_SHIFT,
-		     GPIO7C7_UART2DBG_SOUT << GPIO7C7_SHIFT |
-		     GPIO7C6_UART2DBG_SIN << GPIO7C6_SHIFT);
+#ifdef CONFIG_DEBUG_UART
 	/*
 	 * Debug UART can be used from here if required:
 	 *
@@ -179,6 +171,7 @@ void board_init_f(ulong dummy)
 	 */
 	debug_uart_init();
 	debug("\nspl:debug uart enabled in %s\n", __func__);
+#endif
 	ret = spl_early_init();
 	if (ret) {
 		debug("spl_early_init() failed: %d\n", ret);
diff --git a/arch/arm/mach-rockchip/rk3288-board-tpl.c b/arch/arm/mach-rockchip/rk3288-board-tpl.c
index e34142c..cd2a33b 100644
--- a/arch/arm/mach-rockchip/rk3288-board-tpl.c
+++ b/arch/arm/mach-rockchip/rk3288-board-tpl.c
@@ -13,7 +13,6 @@
 #include <asm/io.h>
 #include <asm/arch/bootrom.h>
 #include <asm/arch/clock.h>
-#include <asm/arch/grf_rk3288.h>
 #include <asm/arch/periph.h>
 #include <asm/arch/pmu_rk3288.h>
 #include <asm/arch/sys_proto.h>
@@ -31,20 +30,12 @@ void rockchip_stimer_init(void)
 	writel(1, CONFIG_ROCKCHIP_STIMER_BASE + 0x10);
 }
 
-#define GRF_BASE		0xff770000
 void board_init_f(ulong dummy)
 {
 	struct udevice *dev;
 	int ret;
 
-	/* Example code showing how to enable the debug UART on RK3288 */
-	/* Enable early UART on the RK3288 */
-	struct rk3288_grf * const grf = (void *)GRF_BASE;
-
-	rk_clrsetreg(&grf->gpio7ch_iomux, GPIO7C7_MASK << GPIO7C7_SHIFT |
-		     GPIO7C6_MASK << GPIO7C6_SHIFT,
-		     GPIO7C7_UART2DBG_SOUT << GPIO7C7_SHIFT |
-		     GPIO7C6_UART2DBG_SIN << GPIO7C6_SHIFT);
+#ifdef CONFIG_DEBUG_UART
 	/*
 	 * Debug UART can be used from here if required:
 	 *
@@ -54,7 +45,7 @@ void board_init_f(ulong dummy)
 	 * printascii("string");
 	 */
 	debug_uart_init();
-
+#endif
 	ret = spl_early_init();
 	if (ret) {
 		debug("spl_early_init() failed: %d\n", ret);
diff --git a/arch/arm/mach-rockchip/rk3288/rk3288.c b/arch/arm/mach-rockchip/rk3288/rk3288.c
index 8f5aaa1..232796e 100644
--- a/arch/arm/mach-rockchip/rk3288/rk3288.c
+++ b/arch/arm/mach-rockchip/rk3288/rk3288.c
@@ -19,3 +19,16 @@ int arch_cpu_init(void)
 
 	return 0;
 }
+
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
+{
+	/* Enable early UART on the RK3288 */
+	struct rk3288_grf * const grf = (void *)GRF_BASE;
+
+	rk_clrsetreg(&grf->gpio7ch_iomux, GPIO7C7_MASK << GPIO7C7_SHIFT |
+		     GPIO7C6_MASK << GPIO7C6_SHIFT,
+		     GPIO7C7_UART2DBG_SOUT << GPIO7C7_SHIFT |
+		     GPIO7C6_UART2DBG_SIN << GPIO7C6_SHIFT);
+}
+#endif
-- 
1.9.1

[U-Boot] [PATCH 08/10] rockchip: rk3368: move board_debug_uart_init() to rk3368.c

[Kever Yang]

Move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file later for all rockchip SoCs.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

 arch/arm/mach-rockchip/rk3368-board-spl.c |  5 -----
 arch/arm/mach-rockchip/rk3368-board-tpl.c | 33 +------------------------------
 arch/arm/mach-rockchip/rk3368/rk3368.c    | 31 +++++++++++++++++++++++++++++
 3 files changed, 32 insertions(+), 37 deletions(-)

diff --git a/arch/arm/mach-rockchip/rk3368-board-spl.c b/arch/arm/mach-rockchip/rk3368-board-spl.c
index 8055ae5..0a4975b 100644
--- a/arch/arm/mach-rockchip/rk3368-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3368-board-spl.c
@@ -12,17 +12,12 @@
 #include <spl.h>
 #include <asm/io.h>
 #include <asm/arch/cru_rk3368.h>
-#include <asm/arch/grf_rk3368.h>
 #include <asm/arch/hardware.h>
 #include <asm/arch/periph.h>
 #include <asm/arch/timer.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
-void board_debug_uart_init(void)
-{
-}
-
 void board_init_f(ulong dummy)
 {
 	struct udevice *pinctrl;
diff --git a/arch/arm/mach-rockchip/rk3368-board-tpl.c b/arch/arm/mach-rockchip/rk3368-board-tpl.c
index 60d5aea..78a2b63 100644
--- a/arch/arm/mach-rockchip/rk3368-board-tpl.c
+++ b/arch/arm/mach-rockchip/rk3368-board-tpl.c
@@ -13,7 +13,6 @@
 #include <asm/io.h>
 #include <asm/arch/bootrom.h>
 #include <asm/arch/cru_rk3368.h>
-#include <asm/arch/grf_rk3368.h>
 #include <asm/arch/hardware.h>
 #include <asm/arch/timer.h>
 #include <syscon.h>
@@ -82,42 +81,12 @@ static void sgrf_init(void)
 	rk_clrreg(&cru->softrst_con[4], DMA2_SRST_REQ);
 }
 
-void board_debug_uart_init(void)
-{
-	/*
-	 * N.B.: This is called before the device-model has been
-	 *       initialised. For this reason, we can not access
-	 *       the GRF address range using the syscon API.
-	 */
-	struct rk3368_grf * const grf =
-		(struct rk3368_grf * const)0xff770000;
-
-	enum {
-		GPIO2D1_MASK            = GENMASK(3, 2),
-		GPIO2D1_GPIO            = 0,
-		GPIO2D1_UART0_SOUT      = (1 << 2),
-
-		GPIO2D0_MASK            = GENMASK(1, 0),
-		GPIO2D0_GPIO            = 0,
-		GPIO2D0_UART0_SIN       = (1 << 0),
-	};
-
-#if defined(CONFIG_DEBUG_UART_BASE) && (CONFIG_DEBUG_UART_BASE == 0xff180000)
-	/* Enable early UART0 on the RK3368 */
-	rk_clrsetreg(&grf->gpio2d_iomux,
-		     GPIO2D0_MASK, GPIO2D0_UART0_SIN);
-	rk_clrsetreg(&grf->gpio2d_iomux,
-		     GPIO2D1_MASK, GPIO2D1_UART0_SOUT);
-#endif
-}
-
 void board_init_f(ulong dummy)
 {
 	struct udevice *dev;
 	int ret;
 
-#define EARLY_UART
-#ifdef EARLY_UART
+#ifdef CONFIG_DEBUG_UART
 	/*
 	 * Debug UART can be used from here if required:
 	 *
diff --git a/arch/arm/mach-rockchip/rk3368/rk3368.c b/arch/arm/mach-rockchip/rk3368/rk3368.c
index f62d91d..2966923 100644
--- a/arch/arm/mach-rockchip/rk3368/rk3368.c
+++ b/arch/arm/mach-rockchip/rk3368/rk3368.c
@@ -97,3 +97,34 @@ int arch_early_init_r(void)
 	return mcu_init();
 }
 #endif
+
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
+{
+	/*
+	 * N.B.: This is called before the device-model has been
+	 *       initialised. For this reason, we can not access
+	 *       the GRF address range using the syscon API.
+	 */
+#if defined(CONFIG_DEBUG_UART_BASE) && (CONFIG_DEBUG_UART_BASE == 0xff180000)
+	struct rk3368_grf * const grf =
+		(struct rk3368_grf * const)0xff770000;
+
+	enum {
+		GPIO2D1_MASK            = GENMASK(3, 2),
+		GPIO2D1_GPIO            = 0,
+		GPIO2D1_UART0_SOUT      = (1 << 2),
+
+		GPIO2D0_MASK            = GENMASK(1, 0),
+		GPIO2D0_GPIO            = 0,
+		GPIO2D0_UART0_SIN       = (1 << 0),
+	};
+
+	/* Enable early UART0 on the RK3368 */
+	rk_clrsetreg(&grf->gpio2d_iomux,
+		     GPIO2D0_MASK, GPIO2D0_UART0_SIN);
+	rk_clrsetreg(&grf->gpio2d_iomux,
+		     GPIO2D1_MASK, GPIO2D1_UART0_SOUT);
+#endif
+}
+#endif
-- 
1.9.1

[U-Boot] [PATCH 09/10] rockchip: rk3399: use grf structure to access reg

[Kever Yang]

Prefer to use structure to access register if we could.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

 arch/arm/mach-rockchip/rk3399/rk3399.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-rockchip/rk3399/rk3399.c b/arch/arm/mach-rockchip/rk3399/rk3399.c
index dbc248f..6a276b9 100644
--- a/arch/arm/mach-rockchip/rk3399/rk3399.c
+++ b/arch/arm/mach-rockchip/rk3399/rk3399.c
@@ -7,11 +7,13 @@
 #include <common.h>
 #include <asm/armv8/mmu.h>
 #include <asm/io.h>
+#include <asm/arch/grf_rk3399.h>
 #include <asm/arch/hardware.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
 #define GRF_EMMCCORE_CON11 0xff77f02c
+#define GRF_BASE	0xff770000
 
 static struct mm_region rk3399_mem_map[] = {
 	{
@@ -49,9 +51,10 @@ int dram_init_banksize(void)
 int arch_cpu_init(void)
 {
 	/* We do some SoC one time setting here. */
+	struct rk3399_grf_regs * const grf = (void *)GRF_BASE;
 
 	/* Emmc clock generator: disable the clock multipilier */
-	rk_clrreg(GRF_EMMCCORE_CON11, 0x0ff);
+	rk_clrreg(&grf->emmccore_con[11], 0x0ff);
 
 	return 0;
 }
-- 
1.9.1

[U-Boot] [PATCH 10/10] rockchip: rk3399: add board_debug_uart_init()

[Kever Yang]

Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file for all rockchip SoCs later.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
---

 arch/arm/mach-rockchip/rk3399-board-spl.c | 31 +------------------------------
 arch/arm/mach-rockchip/rk3399/rk3399.c    | 29 +++++++++++++++++++++++++++++
 2 files changed, 30 insertions(+), 30 deletions(-)

diff --git a/arch/arm/mach-rockchip/rk3399-board-spl.c b/arch/arm/mach-rockchip/rk3399-board-spl.c
index d35990e..f88944f 100644
--- a/arch/arm/mach-rockchip/rk3399-board-spl.c
+++ b/arch/arm/mach-rockchip/rk3399-board-spl.c
@@ -80,34 +80,6 @@ void secure_timer_init(void)
 	writel(TIMER_EN | TIMER_FMODE, TIMER_CHN10_BASE + TIMER_CONTROL_REG);
 }
 
-void board_debug_uart_init(void)
-{
-#define GRF_BASE	0xff770000
-	struct rk3399_grf_regs * const grf = (void *)GRF_BASE;
-
-#if defined(CONFIG_DEBUG_UART_BASE) && (CONFIG_DEBUG_UART_BASE == 0xff180000)
-	/* Enable early UART0 on the RK3399 */
-	rk_clrsetreg(&grf->gpio2c_iomux,
-		     GRF_GPIO2C0_SEL_MASK,
-		     GRF_UART0BT_SIN << GRF_GPIO2C0_SEL_SHIFT);
-	rk_clrsetreg(&grf->gpio2c_iomux,
-		     GRF_GPIO2C1_SEL_MASK,
-		     GRF_UART0BT_SOUT << GRF_GPIO2C1_SEL_SHIFT);
-#else
-	/* Enable early UART2 channel C on the RK3399 */
-	rk_clrsetreg(&grf->gpio4c_iomux,
-		     GRF_GPIO4C3_SEL_MASK,
-		     GRF_UART2DGBC_SIN << GRF_GPIO4C3_SEL_SHIFT);
-	rk_clrsetreg(&grf->gpio4c_iomux,
-		     GRF_GPIO4C4_SEL_MASK,
-		     GRF_UART2DBGC_SOUT << GRF_GPIO4C4_SEL_SHIFT);
-	/* Set channel C as UART2 input */
-	rk_clrsetreg(&grf->soc_con7,
-		     GRF_UART_DBG_SEL_MASK,
-		     GRF_UART_DBG_SEL_C << GRF_UART_DBG_SEL_SHIFT);
-#endif
-}
-
 void board_init_f(ulong dummy)
 {
 	struct udevice *pinctrl;
@@ -116,8 +88,7 @@ void board_init_f(ulong dummy)
 	struct rk3399_grf_regs *grf;
 	int ret;
 
-#define EARLY_UART
-#ifdef EARLY_UART
+#ifdef CONFIG_DEBUG_UART
 	/*
 	 * Debug UART can be used from here if required:
 	 *
diff --git a/arch/arm/mach-rockchip/rk3399/rk3399.c b/arch/arm/mach-rockchip/rk3399/rk3399.c
index 6a276b9..7d64b72 100644
--- a/arch/arm/mach-rockchip/rk3399/rk3399.c
+++ b/arch/arm/mach-rockchip/rk3399/rk3399.c
@@ -58,3 +58,32 @@ int arch_cpu_init(void)
 
 	return 0;
 }
+
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
+{
+	struct rk3399_grf_regs * const grf = (void *)GRF_BASE;
+
+#if defined(CONFIG_DEBUG_UART_BASE) && (CONFIG_DEBUG_UART_BASE == 0xff180000)
+	/* Enable early UART0 on the RK3399 */
+	rk_clrsetreg(&grf->gpio2c_iomux,
+		     GRF_GPIO2C0_SEL_MASK,
+		     GRF_UART0BT_SIN << GRF_GPIO2C0_SEL_SHIFT);
+	rk_clrsetreg(&grf->gpio2c_iomux,
+		     GRF_GPIO2C1_SEL_MASK,
+		     GRF_UART0BT_SOUT << GRF_GPIO2C1_SEL_SHIFT);
+#else
+	/* Enable early UART2 channel C on the RK3399 */
+	rk_clrsetreg(&grf->gpio4c_iomux,
+		     GRF_GPIO4C3_SEL_MASK,
+		     GRF_UART2DGBC_SIN << GRF_GPIO4C3_SEL_SHIFT);
+	rk_clrsetreg(&grf->gpio4c_iomux,
+		     GRF_GPIO4C4_SEL_MASK,
+		     GRF_UART2DBGC_SOUT << GRF_GPIO4C4_SEL_SHIFT);
+	/* Set channel C as UART2 input */
+	rk_clrsetreg(&grf->soc_con7,
+		     GRF_UART_DBG_SEL_MASK,
+		     GRF_UART_DBG_SEL_C << GRF_UART_DBG_SEL_SHIFT);
+#endif
+}
+#endif
-- 
1.9.1

[U-Boot] [PATCH 00/10] rockchip: enable board_debug_uart_init for all soc

[Kever Yang]

Hi Philipp,
    What kind of update do I need to do for this patch set? I didn't get
response mail for this patch set after some search(maybe I didn't do it
correctly). I'm sorry my local mail client only have one month data.
    I can do the update upon the comments/request for it, or just re-send
it base on latest U-Boot.

Thanks,
- Kever


Kever Yang <kever.yang@rock-chips.com> 于2018年4月20日周五 下午12:41写道：

>
> ALl rockchip soc use DEBUG UART, and need init the uart iomux
> in board_debug_uart_init().
> Move the board_debug_uart_init() into soc file so that we can
> make all soc config in soc file and share a common board file
> later for all rockchip SoCs.
>
>
>
> Kever Yang (10):
>   rockchip: enable DEBUG_UART_BOARD_INIT by default
>   rockchip; kylin-rk3036: enabl DEBUG UART
>   rockchip: rk3036: add board_debug_uart_init()
>   rockchip: rk3188: add board_debug_uart_init()
>   rockchip: rk322x: move board_debug_uart_init() to rk322x.c
>   rockchip: rk3288: use grf structure to access soc_con2
>   rockchip: rk3288: add board_debug_uart_init()
>   rockchip: rk3368: move board_debug_uart_init() to rk3368.c
>   rockchip: rk3399: use grf structure to access reg
>   rockchip: rk3399: add board_debug_uart_init()
>
>  arch/arm/Kconfig                          |  2 ++
>  arch/arm/mach-rockchip/Kconfig            |  3 ---
>  arch/arm/mach-rockchip/rk3036-board-spl.c | 19 +------------
>  arch/arm/mach-rockchip/rk3036/Makefile    |  1 +
>  arch/arm/mach-rockchip/rk3036/rk3036.c    | 40 +++++++++++++++++++++++++++
>  arch/arm/mach-rockchip/rk3188-board-spl.c | 12 +--------
>  arch/arm/mach-rockchip/rk3188/Makefile    |  1 +
>  arch/arm/mach-rockchip/rk3188/rk3188.c    | 37 +++++++++++++++++++++++++
>  arch/arm/mach-rockchip/rk322x-board-spl.c | 43
> ++---------------------------
>  arch/arm/mach-rockchip/rk322x-board.c     | 31 +--------------------
>  arch/arm/mach-rockchip/rk322x/Makefile    |  2 +-
>  arch/arm/mach-rockchip/rk322x/rk322x.c    | 45
> +++++++++++++++++++++++++++++++
>  arch/arm/mach-rockchip/rk3288-board-spl.c | 11 ++------
>  arch/arm/mach-rockchip/rk3288-board-tpl.c | 13 ++-------
>  arch/arm/mach-rockchip/rk3288/rk3288.c    | 19 +++++++++++--
>  arch/arm/mach-rockchip/rk3368-board-spl.c |  5 ----
>  arch/arm/mach-rockchip/rk3368-board-tpl.c | 33 +----------------------
>  arch/arm/mach-rockchip/rk3368/rk3368.c    | 31 +++++++++++++++++++++
>  arch/arm/mach-rockchip/rk3399-board-spl.c | 31 +--------------------
>  arch/arm/mach-rockchip/rk3399/rk3399.c    | 34 ++++++++++++++++++++++-
>  configs/kylin-rk3036_defconfig            |  4 +++
>  21 files changed, 223 insertions(+), 194 deletions(-)
>  create mode 100644 arch/arm/mach-rockchip/rk3036/rk3036.c
>  create mode 100644 arch/arm/mach-rockchip/rk3188/rk3188.c
>  create mode 100644 arch/arm/mach-rockchip/rk322x/rk322x.c
>
> --
> 1.9.1
>
>

[U-Boot] [U-Boot, 01/10] rockchip: enable DEBUG_UART_BOARD_INIT by default

[Philipp Tomsich]

> All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
> UART IOMUX, enable it by default.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
>  arch/arm/Kconfig               | 2 ++
>  arch/arm/mach-rockchip/Kconfig | 3 ---
>  2 files changed, 2 insertions(+), 3 deletions(-)
> 

Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot,02/10] rockchip; kylin-rk3036: enabl DEBUG UART

[Philipp Tomsich]

> Enable debug uart for kylin board in defconfig.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
>  configs/kylin-rk3036_defconfig | 4 ++++
>  1 file changed, 4 insertions(+)
> 

Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 03/10] rockchip: rk3036: add board_debug_uart_init()

[Philipp Tomsich]

> Use board_debug_uart_init() for UART iomux init instead of
> do it in board_init_f, and move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3036-board-spl.c | 19 +--------------
>  arch/arm/mach-rockchip/rk3036/Makefile    |  1 +
>  arch/arm/mach-rockchip/rk3036/rk3036.c    | 40 +++++++++++++++++++++++++++++++
>  3 files changed, 42 insertions(+), 18 deletions(-)
>  create mode 100644 arch/arm/mach-rockchip/rk3036/rk3036.c
> 

Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 04/10] rockchip: rk3188: add board_debug_uart_init()

[Philipp Tomsich]

> Use board_debug_uart_init() for UART iomux init instead of
> do it in board_init_f, and move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3188-board-spl.c | 12 +---------
>  arch/arm/mach-rockchip/rk3188/Makefile    |  1 +
>  arch/arm/mach-rockchip/rk3188/rk3188.c    | 37 +++++++++++++++++++++++++++++++
>  3 files changed, 39 insertions(+), 11 deletions(-)
>  create mode 100644 arch/arm/mach-rockchip/rk3188/rk3188.c
> 

Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 05/10] rockchip: rk322x: move board_debug_uart_init() to rk322x.c

[Philipp Tomsich]

> Move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file later for all rockchip SoCs.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
>  arch/arm/mach-rockchip/rk322x-board-spl.c | 43 ++---------------------------
>  arch/arm/mach-rockchip/rk322x-board.c     | 31 +--------------------
>  arch/arm/mach-rockchip/rk322x/Makefile    |  2 +-
>  arch/arm/mach-rockchip/rk322x/rk322x.c    | 45 +++++++++++++++++++++++++++++++
>  4 files changed, 49 insertions(+), 72 deletions(-)
>  create mode 100644 arch/arm/mach-rockchip/rk322x/rk322x.c
> 

Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 07/10] rockchip: rk3288: add board_debug_uart_init()

[Philipp Tomsich]

> Use board_debug_uart_init() for UART iomux init instead of
> do it in board_init_f, and move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file for all rockchip SoCs later.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3288-board-spl.c | 11 ++---------
>  arch/arm/mach-rockchip/rk3288-board-tpl.c | 13 ++-----------
>  arch/arm/mach-rockchip/rk3288/rk3288.c    | 13 +++++++++++++
>  3 files changed, 17 insertions(+), 20 deletions(-)
> 

Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 06/10] rockchip: rk3288: use grf structure to access soc_con2

[Philipp Tomsich]

> Prefer to use structure to access register if we can.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3288/rk3288.c | 6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 

Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 10/10] rockchip: rk3399: add board_debug_uart_init()

[Philipp Tomsich]

> Use board_debug_uart_init() for UART iomux init instead of
> do it in board_init_f, and move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file for all rockchip SoCs later.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3399-board-spl.c | 31 +------------------------------
>  arch/arm/mach-rockchip/rk3399/rk3399.c    | 29 +++++++++++++++++++++++++++++
>  2 files changed, 30 insertions(+), 30 deletions(-)
> 

Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 09/10] rockchip: rk3399: use grf structure to access reg

[Philipp Tomsich]

> Prefer to use structure to access register if we could.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3399/rk3399.c | 5 ++++-
>  1 file changed, 4 insertions(+), 1 deletion(-)
> 

Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 08/10] rockchip: rk3368: move board_debug_uart_init() to rk3368.c

[Philipp Tomsich]

> Move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file later for all rockchip SoCs.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3368-board-spl.c |  5 -----
>  arch/arm/mach-rockchip/rk3368-board-tpl.c | 33 +------------------------------
>  arch/arm/mach-rockchip/rk3368/rk3368.c    | 31 +++++++++++++++++++++++++++++
>  3 files changed, 32 insertions(+), 37 deletions(-)
> 

Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 01/10] rockchip: enable DEBUG_UART_BOARD_INIT by default

[Dr. Philipp Tomsich]

Kever,

Could you rebase this series to u-boot-rockchip/next and resubmit?
I’d like to avoid any issues from manually fixing up git-am issues (as I happened to introduce on last set of UART changes).

Thanks,
Philipp.

> On 29 Aug 2018, at 20:33, Philipp Tomsich <philipp.tomsich@theobroma-systems.com> wrote:
> 
>> All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
>> UART IOMUX, enable it by default.
>> 
>> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
>> ---
>> 
>> arch/arm/Kconfig               | 2 ++
>> arch/arm/mach-rockchip/Kconfig | 3 ---
>> 2 files changed, 2 insertions(+), 3 deletions(-)
>> 
> 
> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot

[U-Boot] [U-Boot, 01/10] rockchip: enable DEBUG_UART_BOARD_INIT by default

[Philipp Tomsich]

> All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
> UART IOMUX, enable it by default.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
> ---
> 
>  arch/arm/Kconfig               | 2 ++
>  arch/arm/mach-rockchip/Kconfig | 3 ---
>  2 files changed, 2 insertions(+), 3 deletions(-)
> 

Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot,02/10] rockchip; kylin-rk3036: enabl DEBUG UART

[Philipp Tomsich]

> Enable debug uart for kylin board in defconfig.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
> ---
> 
>  configs/kylin-rk3036_defconfig | 4 ++++
>  1 file changed, 4 insertions(+)
> 

Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 04/10] rockchip: rk3188: add board_debug_uart_init()

[Philipp Tomsich]

> Use board_debug_uart_init() for UART iomux init instead of
> do it in board_init_f, and move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3188-board-spl.c | 12 +---------
>  arch/arm/mach-rockchip/rk3188/Makefile    |  1 +
>  arch/arm/mach-rockchip/rk3188/rk3188.c    | 37 +++++++++++++++++++++++++++++++
>  3 files changed, 39 insertions(+), 11 deletions(-)
>  create mode 100644 arch/arm/mach-rockchip/rk3188/rk3188.c
> 

Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 06/10] rockchip: rk3288: use grf structure to access soc_con2

[Philipp Tomsich]

> Prefer to use structure to access register if we can.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3288/rk3288.c | 6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 

Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 03/10] rockchip: rk3036: add board_debug_uart_init()

[Philipp Tomsich]

> Use board_debug_uart_init() for UART iomux init instead of
> do it in board_init_f, and move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3036-board-spl.c | 19 +--------------
>  arch/arm/mach-rockchip/rk3036/Makefile    |  1 +
>  arch/arm/mach-rockchip/rk3036/rk3036.c    | 40 +++++++++++++++++++++++++++++++
>  3 files changed, 42 insertions(+), 18 deletions(-)
>  create mode 100644 arch/arm/mach-rockchip/rk3036/rk3036.c
> 

Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 05/10] rockchip: rk322x: move board_debug_uart_init() to rk322x.c

[Philipp Tomsich]

> Move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file later for all rockchip SoCs.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
> ---
> 
>  arch/arm/mach-rockchip/rk322x-board-spl.c | 43 ++---------------------------
>  arch/arm/mach-rockchip/rk322x-board.c     | 31 +--------------------
>  arch/arm/mach-rockchip/rk322x/Makefile    |  2 +-
>  arch/arm/mach-rockchip/rk322x/rk322x.c    | 45 +++++++++++++++++++++++++++++++
>  4 files changed, 49 insertions(+), 72 deletions(-)
>  create mode 100644 arch/arm/mach-rockchip/rk322x/rk322x.c
> 

Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 08/10] rockchip: rk3368: move board_debug_uart_init() to rk3368.c

[Philipp Tomsich]

> Move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file later for all rockchip SoCs.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3368-board-spl.c |  5 -----
>  arch/arm/mach-rockchip/rk3368-board-tpl.c | 33 +------------------------------
>  arch/arm/mach-rockchip/rk3368/rk3368.c    | 31 +++++++++++++++++++++++++++++
>  3 files changed, 32 insertions(+), 37 deletions(-)
> 

Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 09/10] rockchip: rk3399: use grf structure to access reg

[Philipp Tomsich]

> Prefer to use structure to access register if we could.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3399/rk3399.c | 5 ++++-
>  1 file changed, 4 insertions(+), 1 deletion(-)
> 

Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 10/10] rockchip: rk3399: add board_debug_uart_init()

[Philipp Tomsich]

> Use board_debug_uart_init() for UART iomux init instead of
> do it in board_init_f, and move the function to soc file so
> that we can find all the soc/board setting in soc file and
> use a common board file for all rockchip SoCs later.
> 
> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
> ---
> 
>  arch/arm/mach-rockchip/rk3399-board-spl.c | 31 +------------------------------
>  arch/arm/mach-rockchip/rk3399/rk3399.c    | 29 +++++++++++++++++++++++++++++
>  2 files changed, 30 insertions(+), 30 deletions(-)
> 

Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

[U-Boot] [U-Boot, 01/10] rockchip: enable DEBUG_UART_BOARD_INIT by default

[Kever Yang]

Philipp,

Sure, I can do it.


Thanks,
- Kever
On 08/30/2018 02:43 AM, Dr. Philipp Tomsich wrote:
> Kever,
>
> Could you rebase this series to u-boot-rockchip/next and resubmit?
> I’d like to avoid any issues from manually fixing up git-am issues (as I happened to introduce on last set of UART changes).
>
> Thanks,
> Philipp.
>
>> On 29 Aug 2018, at 20:33, Philipp Tomsich <philipp.tomsich@theobroma-systems.com> wrote:
>>
>>> All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
>>> UART IOMUX, enable it by default.
>>>
>>> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
>>> ---
>>>
>>> arch/arm/Kconfig               | 2 ++
>>> arch/arm/mach-rockchip/Kconfig | 3 ---
>>> 2 files changed, 2 insertions(+), 3 deletions(-)
>>>
>> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> https://lists.denx.de/listinfo/u-boot
>

[U-Boot] [U-Boot, 01/10] rockchip: enable DEBUG_UART_BOARD_INIT by default

[Philipp Tomsich]

Kever,

Did I miss the rebased series?
Also note that next is not current at the moment (I haven’t started on next yet), so best to rebase onto the Tom’s master.

Thanks,
Philipp.

> On 30.08.2018, at 03:04, Kever Yang <kever.yang@rock-chips.com> wrote:
> 
> Philipp,
> 
> Sure, I can do it.
> 
> 
> Thanks,
> - Kever
> On 08/30/2018 02:43 AM, Dr. Philipp Tomsich wrote:
>> Kever,
>> 
>> Could you rebase this series to u-boot-rockchip/next and resubmit?
>> I’d like to avoid any issues from manually fixing up git-am issues (as I happened to introduce on last set of UART changes).
>> 
>> Thanks,
>> Philipp.
>> 
>>> On 29 Aug 2018, at 20:33, Philipp Tomsich <philipp.tomsich@theobroma-systems.com> wrote:
>>> 
>>>> All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
>>>> UART IOMUX, enable it by default.
>>>> 
>>>> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
>>>> ---
>>>> 
>>>> arch/arm/Kconfig               | 2 ++
>>>> arch/arm/mach-rockchip/Kconfig | 3 ---
>>>> 2 files changed, 2 insertions(+), 3 deletions(-)
>>>> 
>>> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
>>> _______________________________________________
>>> U-Boot mailing list
>>> U-Boot at lists.denx.de
>>> https://lists.denx.de/listinfo/u-boot
>> 
> 
> 

[U-Boot] [PATCH 00/10] rockchip: enable board_debug_uart_init for all soc

[Kever Yang]

Hi Philipp,

  Ping again.
  I search the patchwork again for this  patch set, and most of them get
your tags: 'Reviewed-by' and 'Acked-by', and I didn't see any change
request for it, can I just rebase them and re-send them? It has been almost
1 year after I send out my patch set.

Thanks,
- Kever
Kever Yang <kever.yang@rock-chips.com> 于2018年8月23日周四 下午6:26写道：

> Hi Philipp,
>     What kind of update do I need to do for this patch set? I didn't get
> response mail for this patch set after some search(maybe I didn't do it
> correctly). I'm sorry my local mail client only have one month data.
>     I can do the update upon the comments/request for it, or just re-send
> it base on latest U-Boot.
>
> Thanks,
> - Kever
>
>
> Kever Yang <kever.yang@rock-chips.com> 于2018年4月20日周五 下午12:41写道：
>
>>
>> ALl rockchip soc use DEBUG UART, and need init the uart iomux
>> in board_debug_uart_init().
>> Move the board_debug_uart_init() into soc file so that we can
>> make all soc config in soc file and share a common board file
>> later for all rockchip SoCs.
>>
>>
>>
>> Kever Yang (10):
>>   rockchip: enable DEBUG_UART_BOARD_INIT by default
>>   rockchip; kylin-rk3036: enabl DEBUG UART
>>   rockchip: rk3036: add board_debug_uart_init()
>>   rockchip: rk3188: add board_debug_uart_init()
>>   rockchip: rk322x: move board_debug_uart_init() to rk322x.c
>>   rockchip: rk3288: use grf structure to access soc_con2
>>   rockchip: rk3288: add board_debug_uart_init()
>>   rockchip: rk3368: move board_debug_uart_init() to rk3368.c
>>   rockchip: rk3399: use grf structure to access reg
>>   rockchip: rk3399: add board_debug_uart_init()
>>
>>  arch/arm/Kconfig                          |  2 ++
>>  arch/arm/mach-rockchip/Kconfig            |  3 ---
>>  arch/arm/mach-rockchip/rk3036-board-spl.c | 19 +------------
>>  arch/arm/mach-rockchip/rk3036/Makefile    |  1 +
>>  arch/arm/mach-rockchip/rk3036/rk3036.c    | 40
>> +++++++++++++++++++++++++++
>>  arch/arm/mach-rockchip/rk3188-board-spl.c | 12 +--------
>>  arch/arm/mach-rockchip/rk3188/Makefile    |  1 +
>>  arch/arm/mach-rockchip/rk3188/rk3188.c    | 37 +++++++++++++++++++++++++
>>  arch/arm/mach-rockchip/rk322x-board-spl.c | 43
>> ++---------------------------
>>  arch/arm/mach-rockchip/rk322x-board.c     | 31 +--------------------
>>  arch/arm/mach-rockchip/rk322x/Makefile    |  2 +-
>>  arch/arm/mach-rockchip/rk322x/rk322x.c    | 45
>> +++++++++++++++++++++++++++++++
>>  arch/arm/mach-rockchip/rk3288-board-spl.c | 11 ++------
>>  arch/arm/mach-rockchip/rk3288-board-tpl.c | 13 ++-------
>>  arch/arm/mach-rockchip/rk3288/rk3288.c    | 19 +++++++++++--
>>  arch/arm/mach-rockchip/rk3368-board-spl.c |  5 ----
>>  arch/arm/mach-rockchip/rk3368-board-tpl.c | 33 +----------------------
>>  arch/arm/mach-rockchip/rk3368/rk3368.c    | 31 +++++++++++++++++++++
>>  arch/arm/mach-rockchip/rk3399-board-spl.c | 31 +--------------------
>>  arch/arm/mach-rockchip/rk3399/rk3399.c    | 34 ++++++++++++++++++++++-
>>  configs/kylin-rk3036_defconfig            |  4 +++
>>  21 files changed, 223 insertions(+), 194 deletions(-)
>>  create mode 100644 arch/arm/mach-rockchip/rk3036/rk3036.c
>>  create mode 100644 arch/arm/mach-rockchip/rk3188/rk3188.c
>>  create mode 100644 arch/arm/mach-rockchip/rk322x/rk322x.c
>>
>> --
>> 1.9.1
>>
>>

[U-Boot] [PATCH 00/10] rockchip: enable board_debug_uart_init for all soc

[Philipp Tomsich]

Last I remember was that I had requested a rebase, as they didn’t apply cleanly any longer.

> On 28.03.2019, at 11:52, Kever Yang <kever.yang@rock-chips.com> wrote:
> 
> Hi Philipp,
> 
>   Ping again.
>   I search the patchwork again for this  patch set, and most of them get your tags: 'Reviewed-by' and 'Acked-by', and I didn't see any change request for it, can I just rebase them and re-send them? It has been almost 1 year after I send out my patch set.
> 
> Thanks,
> - Kever
> Kever Yang <kever.yang at rock-chips.com <mailto:kever.yang@rock-chips.com>> 于2018年8月23日周四 下午6:26写道：
> Hi Philipp,
>     What kind of update do I need to do for this patch set? I didn't get response mail for this patch set after some search(maybe I didn't do it correctly). I'm sorry my local mail client only have one month data.
>     I can do the update upon the comments/request for it, or just re-send it base on latest U-Boot.
> 
> Thanks,
> - Kever
> 
> 
> Kever Yang <kever.yang at rock-chips.com <mailto:kever.yang@rock-chips.com>> 于2018年4月20日周五 下午12:41写道：
> 
> ALl rockchip soc use DEBUG UART, and need init the uart iomux
> in board_debug_uart_init().
> Move the board_debug_uart_init() into soc file so that we can
> make all soc config in soc file and share a common board file
> later for all rockchip SoCs.
> 
> 
> 
> Kever Yang (10):
>   rockchip: enable DEBUG_UART_BOARD_INIT by default
>   rockchip; kylin-rk3036: enabl DEBUG UART
>   rockchip: rk3036: add board_debug_uart_init()
>   rockchip: rk3188: add board_debug_uart_init()
>   rockchip: rk322x: move board_debug_uart_init() to rk322x.c
>   rockchip: rk3288: use grf structure to access soc_con2
>   rockchip: rk3288: add board_debug_uart_init()
>   rockchip: rk3368: move board_debug_uart_init() to rk3368.c
>   rockchip: rk3399: use grf structure to access reg
>   rockchip: rk3399: add board_debug_uart_init()
> 
>  arch/arm/Kconfig                          |  2 ++
>  arch/arm/mach-rockchip/Kconfig            |  3 ---
>  arch/arm/mach-rockchip/rk3036-board-spl.c | 19 +------------
>  arch/arm/mach-rockchip/rk3036/Makefile    |  1 +
>  arch/arm/mach-rockchip/rk3036/rk3036.c    | 40 +++++++++++++++++++++++++++
>  arch/arm/mach-rockchip/rk3188-board-spl.c | 12 +--------
>  arch/arm/mach-rockchip/rk3188/Makefile    |  1 +
>  arch/arm/mach-rockchip/rk3188/rk3188.c    | 37 +++++++++++++++++++++++++
>  arch/arm/mach-rockchip/rk322x-board-spl.c | 43 ++---------------------------
>  arch/arm/mach-rockchip/rk322x-board.c     | 31 +--------------------
>  arch/arm/mach-rockchip/rk322x/Makefile    |  2 +-
>  arch/arm/mach-rockchip/rk322x/rk322x.c    | 45 +++++++++++++++++++++++++++++++
>  arch/arm/mach-rockchip/rk3288-board-spl.c | 11 ++------
>  arch/arm/mach-rockchip/rk3288-board-tpl.c | 13 ++-------
>  arch/arm/mach-rockchip/rk3288/rk3288.c    | 19 +++++++++++--
>  arch/arm/mach-rockchip/rk3368-board-spl.c |  5 ----
>  arch/arm/mach-rockchip/rk3368-board-tpl.c | 33 +----------------------
>  arch/arm/mach-rockchip/rk3368/rk3368.c    | 31 +++++++++++++++++++++
>  arch/arm/mach-rockchip/rk3399-board-spl.c | 31 +--------------------
>  arch/arm/mach-rockchip/rk3399/rk3399.c    | 34 ++++++++++++++++++++++-
>  configs/kylin-rk3036_defconfig            |  4 +++
>  21 files changed, 223 insertions(+), 194 deletions(-)
>  create mode 100644 arch/arm/mach-rockchip/rk3036/rk3036.c
>  create mode 100644 arch/arm/mach-rockchip/rk3188/rk3188.c
>  create mode 100644 arch/arm/mach-rockchip/rk322x/rk322x.c
> 
> -- 
> 1.9.1
>