* [PATCH 0/2] ARM: dts: stm32: add qspi support for stm32mp157c
@ 2018-04-30 7:11 ` Ludovic Barre
0 siblings, 0 replies; 12+ messages in thread
From: Ludovic Barre @ 2018-04-30 7:11 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: Maxime Coquelin, Alexandre Torgue, devicetree, linux-arm-kernel,
linux-kernel, Ludovic Barre
From: Ludovic Barre <ludovic.barre@st.com>
This patch series adds qspi support for stm32mp157c SoC
and its eval board.
Ludovic Barre (2):
ARM: dts: stm32: add qspi support for stm32mp157c
ARM: dts: stm32: add flash nor support on stm32mp157c eval board
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 45 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-ev1.dts | 25 +++++++++++++++++
arch/arm/boot/dts/stm32mp157c.dtsi | 11 ++++++++
3 files changed, 81 insertions(+)
--
2.7.4
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 0/2] ARM: dts: stm32: add qspi support for stm32mp157c
@ 2018-04-30 7:11 ` Ludovic Barre
0 siblings, 0 replies; 12+ messages in thread
From: Ludovic Barre @ 2018-04-30 7:11 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: Maxime Coquelin, Alexandre Torgue, devicetree, linux-arm-kernel,
linux-kernel, Ludovic Barre
From: Ludovic Barre <ludovic.barre@st.com>
This patch series adds qspi support for stm32mp157c SoC
and its eval board.
Ludovic Barre (2):
ARM: dts: stm32: add qspi support for stm32mp157c
ARM: dts: stm32: add flash nor support on stm32mp157c eval board
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 45 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-ev1.dts | 25 +++++++++++++++++
arch/arm/boot/dts/stm32mp157c.dtsi | 11 ++++++++
3 files changed, 81 insertions(+)
--
2.7.4
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 0/2] ARM: dts: stm32: add qspi support for stm32mp157c
@ 2018-04-30 7:11 ` Ludovic Barre
0 siblings, 0 replies; 12+ messages in thread
From: Ludovic Barre @ 2018-04-30 7:11 UTC (permalink / raw)
To: linux-arm-kernel
From: Ludovic Barre <ludovic.barre@st.com>
This patch series adds qspi support for stm32mp157c SoC
and its eval board.
Ludovic Barre (2):
ARM: dts: stm32: add qspi support for stm32mp157c
ARM: dts: stm32: add flash nor support on stm32mp157c eval board
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 45 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-ev1.dts | 25 +++++++++++++++++
arch/arm/boot/dts/stm32mp157c.dtsi | 11 ++++++++
3 files changed, 81 insertions(+)
--
2.7.4
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/2] ARM: dts: stm32: add qspi support for stm32mp157c
2018-04-30 7:11 ` Ludovic Barre
(?)
@ 2018-04-30 7:11 ` Ludovic Barre
-1 siblings, 0 replies; 12+ messages in thread
From: Ludovic Barre @ 2018-04-30 7:11 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: Maxime Coquelin, Alexandre Torgue, devicetree, linux-arm-kernel,
linux-kernel, Ludovic Barre
From: Ludovic Barre <ludovic.barre@st.com>
This patch adds qspi support on stm32mp157c,
read in memory mapped, write in indirect mode.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
arch/arm/boot/dts/stm32mp157c.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi
index bfcf84b..7714949 100644
--- a/arch/arm/boot/dts/stm32mp157c.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c.dtsi
@@ -5,6 +5,7 @@
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/stm32mp1-clks.h>
+#include <dt-bindings/reset/stm32mp1-resets.h>
/ {
#address-cells = <1>;
@@ -167,6 +168,16 @@
#reset-cells = <1>;
};
+ qspi: qspi@58003000 {
+ compatible = "st,stm32f469-qspi";
+ reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
+ reg-names = "qspi", "qspi_mm";
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc QSPI_K>;
+ resets = <&rcc QSPI_R>;
+ status = "disabled";
+ };
+
usart1: serial@5c000000 {
compatible = "st,stm32h7-uart";
reg = <0x5c000000 0x400>;
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 1/2] ARM: dts: stm32: add qspi support for stm32mp157c
@ 2018-04-30 7:11 ` Ludovic Barre
0 siblings, 0 replies; 12+ messages in thread
From: Ludovic Barre @ 2018-04-30 7:11 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: Maxime Coquelin, Alexandre Torgue, devicetree, linux-arm-kernel,
linux-kernel, Ludovic Barre
From: Ludovic Barre <ludovic.barre@st.com>
This patch adds qspi support on stm32mp157c,
read in memory mapped, write in indirect mode.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
arch/arm/boot/dts/stm32mp157c.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi
index bfcf84b..7714949 100644
--- a/arch/arm/boot/dts/stm32mp157c.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c.dtsi
@@ -5,6 +5,7 @@
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/stm32mp1-clks.h>
+#include <dt-bindings/reset/stm32mp1-resets.h>
/ {
#address-cells = <1>;
@@ -167,6 +168,16 @@
#reset-cells = <1>;
};
+ qspi: qspi@58003000 {
+ compatible = "st,stm32f469-qspi";
+ reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
+ reg-names = "qspi", "qspi_mm";
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc QSPI_K>;
+ resets = <&rcc QSPI_R>;
+ status = "disabled";
+ };
+
usart1: serial@5c000000 {
compatible = "st,stm32h7-uart";
reg = <0x5c000000 0x400>;
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 1/2] ARM: dts: stm32: add qspi support for stm32mp157c
@ 2018-04-30 7:11 ` Ludovic Barre
0 siblings, 0 replies; 12+ messages in thread
From: Ludovic Barre @ 2018-04-30 7:11 UTC (permalink / raw)
To: linux-arm-kernel
From: Ludovic Barre <ludovic.barre@st.com>
This patch adds qspi support on stm32mp157c,
read in memory mapped, write in indirect mode.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
arch/arm/boot/dts/stm32mp157c.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi
index bfcf84b..7714949 100644
--- a/arch/arm/boot/dts/stm32mp157c.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c.dtsi
@@ -5,6 +5,7 @@
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/stm32mp1-clks.h>
+#include <dt-bindings/reset/stm32mp1-resets.h>
/ {
#address-cells = <1>;
@@ -167,6 +168,16 @@
#reset-cells = <1>;
};
+ qspi: qspi at 58003000 {
+ compatible = "st,stm32f469-qspi";
+ reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
+ reg-names = "qspi", "qspi_mm";
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc QSPI_K>;
+ resets = <&rcc QSPI_R>;
+ status = "disabled";
+ };
+
usart1: serial at 5c000000 {
compatible = "st,stm32h7-uart";
reg = <0x5c000000 0x400>;
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/2] ARM: dts: stm32: add flash nor support on stm32mp157c eval board
2018-04-30 7:11 ` Ludovic Barre
(?)
@ 2018-04-30 7:11 ` Ludovic Barre
-1 siblings, 0 replies; 12+ messages in thread
From: Ludovic Barre @ 2018-04-30 7:11 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: Maxime Coquelin, Alexandre Torgue, devicetree, linux-arm-kernel,
linux-kernel, Ludovic Barre
From: Ludovic Barre <ludovic.barre@st.com>
This patch adds flash nor on qspi. Each flash is
connected in quad mode and has its own chip select.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 45 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-ev1.dts | 25 +++++++++++++++++
2 files changed, 70 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
index 6f044100..9d4c553 100644
--- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -146,6 +146,51 @@
gpio-ranges = <&pinctrl 0 160 8>;
};
+ qspi_clk_pins_a: qspi-clk-0 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 10, AF9)>; /* QSPI_CLK */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ };
+
+ qspi_bk1_pins_a: qspi-bk1-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */
+ <STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */
+ <STM32_PINMUX('F', 7, AF9)>, /* QSPI_BK1_IO2 */
+ <STM32_PINMUX('F', 6, AF9)>; /* QSPI_BK1_IO3 */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
+ bias-pull-up;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ };
+
+ qspi_bk2_pins_a: qspi-bk2-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('H', 2, AF9)>, /* QSPI_BK2_IO0 */
+ <STM32_PINMUX('H', 3, AF9)>, /* QSPI_BK2_IO1 */
+ <STM32_PINMUX('G', 10, AF11)>, /* QSPI_BK2_IO2 */
+ <STM32_PINMUX('G', 7, AF11)>; /* QSPI_BK2_IO3 */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */
+ bias-pull-up;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ };
+
uart4_pins_a: uart4@0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 57e6dbc..96c2aee 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -19,3 +19,28 @@
serial0 = &uart4;
};
};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+ reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash0: mx66l51235l@0 {
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ flash1: mx66l51235l@1 {
+ reg = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/2] ARM: dts: stm32: add flash nor support on stm32mp157c eval board
@ 2018-04-30 7:11 ` Ludovic Barre
0 siblings, 0 replies; 12+ messages in thread
From: Ludovic Barre @ 2018-04-30 7:11 UTC (permalink / raw)
To: Rob Herring, Mark Rutland
Cc: Maxime Coquelin, Alexandre Torgue, devicetree, linux-arm-kernel,
linux-kernel, Ludovic Barre
From: Ludovic Barre <ludovic.barre@st.com>
This patch adds flash nor on qspi. Each flash is
connected in quad mode and has its own chip select.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 45 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-ev1.dts | 25 +++++++++++++++++
2 files changed, 70 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
index 6f044100..9d4c553 100644
--- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -146,6 +146,51 @@
gpio-ranges = <&pinctrl 0 160 8>;
};
+ qspi_clk_pins_a: qspi-clk-0 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 10, AF9)>; /* QSPI_CLK */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ };
+
+ qspi_bk1_pins_a: qspi-bk1-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */
+ <STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */
+ <STM32_PINMUX('F', 7, AF9)>, /* QSPI_BK1_IO2 */
+ <STM32_PINMUX('F', 6, AF9)>; /* QSPI_BK1_IO3 */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
+ bias-pull-up;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ };
+
+ qspi_bk2_pins_a: qspi-bk2-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('H', 2, AF9)>, /* QSPI_BK2_IO0 */
+ <STM32_PINMUX('H', 3, AF9)>, /* QSPI_BK2_IO1 */
+ <STM32_PINMUX('G', 10, AF11)>, /* QSPI_BK2_IO2 */
+ <STM32_PINMUX('G', 7, AF11)>; /* QSPI_BK2_IO3 */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */
+ bias-pull-up;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ };
+
uart4_pins_a: uart4@0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 57e6dbc..96c2aee 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -19,3 +19,28 @@
serial0 = &uart4;
};
};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+ reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash0: mx66l51235l@0 {
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ flash1: mx66l51235l@1 {
+ reg = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/2] ARM: dts: stm32: add flash nor support on stm32mp157c eval board
@ 2018-04-30 7:11 ` Ludovic Barre
0 siblings, 0 replies; 12+ messages in thread
From: Ludovic Barre @ 2018-04-30 7:11 UTC (permalink / raw)
To: linux-arm-kernel
From: Ludovic Barre <ludovic.barre@st.com>
This patch adds flash nor on qspi. Each flash is
connected in quad mode and has its own chip select.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 45 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/stm32mp157c-ev1.dts | 25 +++++++++++++++++
2 files changed, 70 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
index 6f044100..9d4c553 100644
--- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -146,6 +146,51 @@
gpio-ranges = <&pinctrl 0 160 8>;
};
+ qspi_clk_pins_a: qspi-clk-0 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 10, AF9)>; /* QSPI_CLK */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ };
+
+ qspi_bk1_pins_a: qspi-bk1-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */
+ <STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */
+ <STM32_PINMUX('F', 7, AF9)>, /* QSPI_BK1_IO2 */
+ <STM32_PINMUX('F', 6, AF9)>; /* QSPI_BK1_IO3 */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
+ bias-pull-up;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ };
+
+ qspi_bk2_pins_a: qspi-bk2-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('H', 2, AF9)>, /* QSPI_BK2_IO0 */
+ <STM32_PINMUX('H', 3, AF9)>, /* QSPI_BK2_IO1 */
+ <STM32_PINMUX('G', 10, AF11)>, /* QSPI_BK2_IO2 */
+ <STM32_PINMUX('G', 7, AF11)>; /* QSPI_BK2_IO3 */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */
+ bias-pull-up;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ };
+
uart4_pins_a: uart4 at 0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 57e6dbc..96c2aee 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -19,3 +19,28 @@
serial0 = &uart4;
};
};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+ reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash0: mx66l51235l at 0 {
+ reg = <0>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+
+ flash1: mx66l51235l at 1 {
+ reg = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <108000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 0/2] ARM: dts: stm32: add qspi support for stm32mp157c
2018-04-30 7:11 ` Ludovic Barre
(?)
@ 2018-05-03 13:06 ` Alexandre Torgue
-1 siblings, 0 replies; 12+ messages in thread
From: Alexandre Torgue @ 2018-05-03 13:06 UTC (permalink / raw)
To: Ludovic Barre, Rob Herring, Mark Rutland
Cc: Maxime Coquelin, devicetree, linux-arm-kernel, linux-kernel
Hi Ludovic,
On 04/30/2018 09:11 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
>
> This patch series adds qspi support for stm32mp157c SoC
> and its eval board.
>
> Ludovic Barre (2):
> ARM: dts: stm32: add qspi support for stm32mp157c
> ARM: dts: stm32: add flash nor support on stm32mp157c eval board
>
> arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 45 +++++++++++++++++++++++++++++++
> arch/arm/boot/dts/stm32mp157c-ev1.dts | 25 +++++++++++++++++
> arch/arm/boot/dts/stm32mp157c.dtsi | 11 ++++++++
> 3 files changed, 81 insertions(+)
>
Series applied on stm32-next.
Regards
Alex
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 0/2] ARM: dts: stm32: add qspi support for stm32mp157c
@ 2018-05-03 13:06 ` Alexandre Torgue
0 siblings, 0 replies; 12+ messages in thread
From: Alexandre Torgue @ 2018-05-03 13:06 UTC (permalink / raw)
To: Ludovic Barre, Rob Herring, Mark Rutland
Cc: Maxime Coquelin, devicetree, linux-arm-kernel, linux-kernel
Hi Ludovic,
On 04/30/2018 09:11 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
>
> This patch series adds qspi support for stm32mp157c SoC
> and its eval board.
>
> Ludovic Barre (2):
> ARM: dts: stm32: add qspi support for stm32mp157c
> ARM: dts: stm32: add flash nor support on stm32mp157c eval board
>
> arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 45 +++++++++++++++++++++++++++++++
> arch/arm/boot/dts/stm32mp157c-ev1.dts | 25 +++++++++++++++++
> arch/arm/boot/dts/stm32mp157c.dtsi | 11 ++++++++
> 3 files changed, 81 insertions(+)
>
Series applied on stm32-next.
Regards
Alex
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 0/2] ARM: dts: stm32: add qspi support for stm32mp157c
@ 2018-05-03 13:06 ` Alexandre Torgue
0 siblings, 0 replies; 12+ messages in thread
From: Alexandre Torgue @ 2018-05-03 13:06 UTC (permalink / raw)
To: linux-arm-kernel
Hi Ludovic,
On 04/30/2018 09:11 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
>
> This patch series adds qspi support for stm32mp157c SoC
> and its eval board.
>
> Ludovic Barre (2):
> ARM: dts: stm32: add qspi support for stm32mp157c
> ARM: dts: stm32: add flash nor support on stm32mp157c eval board
>
> arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 45 +++++++++++++++++++++++++++++++
> arch/arm/boot/dts/stm32mp157c-ev1.dts | 25 +++++++++++++++++
> arch/arm/boot/dts/stm32mp157c.dtsi | 11 ++++++++
> 3 files changed, 81 insertions(+)
>
Series applied on stm32-next.
Regards
Alex
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2018-05-03 13:07 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-04-30 7:11 [PATCH 0/2] ARM: dts: stm32: add qspi support for stm32mp157c Ludovic Barre
2018-04-30 7:11 ` Ludovic Barre
2018-04-30 7:11 ` Ludovic Barre
2018-04-30 7:11 ` [PATCH 1/2] " Ludovic Barre
2018-04-30 7:11 ` Ludovic Barre
2018-04-30 7:11 ` Ludovic Barre
2018-04-30 7:11 ` [PATCH 2/2] ARM: dts: stm32: add flash nor support on stm32mp157c eval board Ludovic Barre
2018-04-30 7:11 ` Ludovic Barre
2018-04-30 7:11 ` Ludovic Barre
2018-05-03 13:06 ` [PATCH 0/2] ARM: dts: stm32: add qspi support for stm32mp157c Alexandre Torgue
2018-05-03 13:06 ` Alexandre Torgue
2018-05-03 13:06 ` Alexandre Torgue
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.