* [PATCH v5 0/7] phy: qcom: Updates for USB PHYs on SDM845
@ 2018-05-02 21:00 Manu Gautam
0 siblings, 0 replies; 2+ messages in thread
From: Manu Gautam @ 2018-05-02 21:00 UTC (permalink / raw)
To: Kishon Vijay Abraham I, robh, sboyd
Cc: devicetree, linux-kernel, dianders, evgreen, Vivek Gautam,
linux-arm-msm, linux-usb, Manu Gautam
SDM845 has two USB instances each with QUSB2 and QMP PHYs.
One of the QMP PHY is USB-DP (DisplayPort) combo PHY where
as other one is single lane UNI-PHY (without DP support).
Changes are related to PHY configuration for electrical
parameters tuning to improve eye-diagram and some fixes.
First gcc-msm8996 driver patch is dependent on following
patch which is now applied by Stephen.
https://patchwork.kernel.org/patch/10375043/
Changes since v4:
- Addressed Doug's review comments to have QUSB2 PHY tuning
values in header file.
- Updated msm8996-gcc patch to use BRANCH_HALT_SKIP flag
added by patch - https://patchwork.kernel.org/patch/10375041/
Changes since v3:
- As per Doug's review comments added device tree parameters
to handle board level differences in PHY tuning values instead
of adding separate device tree bindings.
- Replace PHY version specific bindings names with SOC name as
no one is going to use generic binding names.
- Update halt_check to not check for pipe clock status that
allows to simplify pipe_clk handling in QMP driver.
Changes since v2:
- Use separate phy_ops for USB to not register power_on op.
- And other minor changes as per review comments from Stephen.
Changes since v1:
- Updated qusb2 compatibility name as per comment from Vivek.
Manu Gautam (7):
clk: msm8996-gcc: Mark halt check as no-op for USB/PCIE pipe_clk
phy: qcom-qmp: Enable pipe_clk before PHY initialization
phy: qcom-qusb2: Fix crash if nvmem cell not specified
dt-bindings: phy-qcom-qmp: Update bindings for sdm845
phy: qcom-qmp: Add QMP V3 USB3 UNI PHY support for sdm845
dt-bindings: phy-qcom-usb2: Add support to override tuning values
phy: qcom-qusb2: Add QUSB2 PHYs support for sdm845
.../devicetree/bindings/phy/qcom-qmp-phy.txt | 3 +-
.../devicetree/bindings/phy/qcom-qusb2-phy.txt | 23 ++-
drivers/clk/qcom/gcc-msm8996.c | 4 +
drivers/phy/qualcomm/phy-qcom-qmp.c | 169 +++++++++++++++++++--
drivers/phy/qualcomm/phy-qcom-qmp.h | 5 +
drivers/phy/qualcomm/phy-qcom-qusb2.c | 130 +++++++++++++++-
include/dt-bindings/phy/phy-qcom-qusb2.h | 37 +++++
7 files changed, 346 insertions(+), 25 deletions(-)
create mode 100644 include/dt-bindings/phy/phy-qcom-qusb2.h
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 2+ messages in thread
* [PATCH v5 0/7] phy: qcom: Updates for USB PHYs on SDM845
@ 2018-05-02 21:06 Manu Gautam
0 siblings, 0 replies; 2+ messages in thread
From: Manu Gautam @ 2018-05-02 21:06 UTC (permalink / raw)
To: Kishon Vijay Abraham I, robh, sboyd
Cc: devicetree, linux-kernel, dianders, evgreen, Vivek Gautam,
linux-arm-msm, linux-usb, Manu Gautam
SDM845 has two USB instances each with QUSB2 and QMP PHYs.
One of the QMP PHY is USB-DP (DisplayPort) combo PHY where
as other one is single lane UNI-PHY (without DP support).
Changes are related to PHY configuration for electrical
parameters tuning to improve eye-diagram and some fixes.
First gcc-msm8996 driver patch is dependent on following
patch which is now applied by Stephen.
https://patchwork.kernel.org/patch/10375043/
Changes since v4:
- Addressed Doug's review comments to have QUSB2 PHY tuning
values in header file.
- Updated msm8996-gcc patch to use BRANCH_HALT_SKIP flag
added by patch - https://patchwork.kernel.org/patch/10375041/
Changes since v3:
- As per Doug's review comments added device tree parameters
to handle board level differences in PHY tuning values instead
of adding separate device tree bindings.
- Replace PHY version specific bindings names with SOC name as
no one is going to use generic binding names.
- Update halt_check to not check for pipe clock status that
allows to simplify pipe_clk handling in QMP driver.
Changes since v2:
- Use separate phy_ops for USB to not register power_on op.
- And other minor changes as per review comments from Stephen.
Changes since v1:
- Updated qusb2 compatibility name as per comment from Vivek.
Manu Gautam (7):
clk: msm8996-gcc: Mark halt check as no-op for USB/PCIE pipe_clk
phy: qcom-qmp: Enable pipe_clk before PHY initialization
phy: qcom-qusb2: Fix crash if nvmem cell not specified
dt-bindings: phy-qcom-qmp: Update bindings for sdm845
phy: qcom-qmp: Add QMP V3 USB3 UNI PHY support for sdm845
dt-bindings: phy-qcom-usb2: Add support to override tuning values
phy: qcom-qusb2: Add QUSB2 PHYs support for sdm845
.../devicetree/bindings/phy/qcom-qmp-phy.txt | 3 +-
.../devicetree/bindings/phy/qcom-qusb2-phy.txt | 23 ++-
drivers/clk/qcom/gcc-msm8996.c | 4 +
drivers/phy/qualcomm/phy-qcom-qmp.c | 169 +++++++++++++++++++--
drivers/phy/qualcomm/phy-qcom-qmp.h | 5 +
drivers/phy/qualcomm/phy-qcom-qusb2.c | 130 +++++++++++++++-
include/dt-bindings/phy/phy-qcom-qusb2.h | 37 +++++
7 files changed, 346 insertions(+), 25 deletions(-)
create mode 100644 include/dt-bindings/phy/phy-qcom-qusb2.h
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2018-05-02 21:06 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-05-02 21:00 [PATCH v5 0/7] phy: qcom: Updates for USB PHYs on SDM845 Manu Gautam
2018-05-02 21:06 Manu Gautam
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.