[PATCH 0/2] add syscfg mask parameter

[PATCH 0/2] add syscfg mask parameter

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch series adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
This parameter is needed if the mask is different of 0xf.

Ludovic Barre (2):
  dt-bindings: pinctrl: add syscfg mask parameter
  pinctrl: stm32: add syscfg mask parameter

 .../devicetree/bindings/pinctrl/st,stm32-pinctrl.txt     |  7 ++++---
 drivers/pinctrl/stm32/pinctrl-stm32.c                    | 16 ++++++++++++++--
 2 files changed, 18 insertions(+), 5 deletions(-)

-- 
2.7.4

[PATCH 0/2] add syscfg mask parameter

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch series adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
This parameter is needed if the mask is different of 0xf.

Ludovic Barre (2):
  dt-bindings: pinctrl: add syscfg mask parameter
  pinctrl: stm32: add syscfg mask parameter

 .../devicetree/bindings/pinctrl/st,stm32-pinctrl.txt     |  7 ++++---
 drivers/pinctrl/stm32/pinctrl-stm32.c                    | 16 ++++++++++++++--
 2 files changed, 18 insertions(+), 5 deletions(-)

-- 
2.7.4

[PATCH 0/2] add syscfg mask parameter

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch series adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
This parameter is needed if the mask is different of 0xf.

Ludovic Barre (2):
  dt-bindings: pinctrl: add syscfg mask parameter
  pinctrl: stm32: add syscfg mask parameter

 .../devicetree/bindings/pinctrl/st,stm32-pinctrl.txt     |  7 ++++---
 drivers/pinctrl/stm32/pinctrl-stm32.c                    | 16 ++++++++++++++--
 2 files changed, 18 insertions(+), 5 deletions(-)

-- 
2.7.4

[PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
This parameter is needed if the mask is different of 0xf.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
index 9a06e1f..4d60119 100644
--- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
@@ -39,9 +39,10 @@ Optional properties:
  - reset:	  : Reference to the reset controller
  - interrupt-parent: phandle of the interrupt parent to which the external
    GPIO interrupts are forwarded to.
- - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
-   which includes IRQ mux selection register, and the offset of the IRQ mux
-   selection register.
+ - st,syscfg: Should be phandle/offset/mask.
+	-The phandle to the syscon node which includes IRQ mux selection register.
+	-The offset of the IRQ mux selection register
+	-The field mask of IRQ mux, needed if different of 0xf.
  - gpio-ranges: Define a dedicated mapping between a pin-controller and
    a gpio controller. Format is <&phandle a b c> with:
 	-(phandle): phandle of pin-controller.
-- 
2.7.4

[PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
This parameter is needed if the mask is different of 0xf.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
index 9a06e1f..4d60119 100644
--- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
@@ -39,9 +39,10 @@ Optional properties:
  - reset:	  : Reference to the reset controller
  - interrupt-parent: phandle of the interrupt parent to which the external
    GPIO interrupts are forwarded to.
- - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
-   which includes IRQ mux selection register, and the offset of the IRQ mux
-   selection register.
+ - st,syscfg: Should be phandle/offset/mask.
+	-The phandle to the syscon node which includes IRQ mux selection register.
+	-The offset of the IRQ mux selection register
+	-The field mask of IRQ mux, needed if different of 0xf.
  - gpio-ranges: Define a dedicated mapping between a pin-controller and
    a gpio controller. Format is <&phandle a b c> with:
 	-(phandle): phandle of pin-controller.
-- 
2.7.4

[PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
This parameter is needed if the mask is different of 0xf.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
index 9a06e1f..4d60119 100644
--- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
@@ -39,9 +39,10 @@ Optional properties:
  - reset:	  : Reference to the reset controller
  - interrupt-parent: phandle of the interrupt parent to which the external
    GPIO interrupts are forwarded to.
- - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
-   which includes IRQ mux selection register, and the offset of the IRQ mux
-   selection register.
+ - st,syscfg: Should be phandle/offset/mask.
+	-The phandle to the syscon node which includes IRQ mux selection register.
+	-The offset of the IRQ mux selection register
+	-The field mask of IRQ mux, needed if different of 0xf.
  - gpio-ranges: Define a dedicated mapping between a pin-controller and
    a gpio controller. Format is <&phandle a b c> with:
 	-(phandle): phandle of pin-controller.
-- 
2.7.4

[PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
To avoid backward compatibility, the drivers set
the legacy value by default.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/pinctrl/stm32/pinctrl-stm32.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)

diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c b/drivers/pinctrl/stm32/pinctrl-stm32.c
index dfed609..f756232 100644
--- a/drivers/pinctrl/stm32/pinctrl-stm32.c
+++ b/drivers/pinctrl/stm32/pinctrl-stm32.c
@@ -46,6 +46,8 @@
 #define STM32_GPIO_PINS_PER_BANK 16
 #define STM32_GPIO_IRQ_LINE	 16
 
+#define SYSCFG_IRQMUX_MASK GENMASK(3, 0)
+
 #define gpio_range_to_bank(chip) \
 		container_of(chip, struct stm32_gpio_bank, range)
 
@@ -1033,6 +1035,7 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
 	struct device *dev = &pdev->dev;
 	struct regmap *rm;
 	int offset, ret, i;
+	int mask, mask_width;
 
 	parent = of_irq_find_parent(np);
 	if (!parent)
@@ -1052,12 +1055,21 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
 	if (ret)
 		return ret;
 
+	ret = of_property_read_u32_index(np, "st,syscfg", 2, &mask);
+	if (ret)
+		mask = SYSCFG_IRQMUX_MASK;
+
+	mask_width = fls(mask);
+
 	for (i = 0; i < STM32_GPIO_PINS_PER_BANK; i++) {
 		struct reg_field mux;
 
 		mux.reg = offset + (i / 4) * 4;
-		mux.lsb = (i % 4) * 4;
-		mux.msb = mux.lsb + 3;
+		mux.lsb = (i % 4) * mask_width;
+		mux.msb = mux.lsb + mask_width - 1;
+
+		dev_dbg(dev, "irqmux%d: reg:%#x, lsb:%d, msb:%d\n",
+			i, mux.reg, mux.lsb, mux.msb);
 
 		pctl->irqmux[i] = devm_regmap_field_alloc(dev, rm, mux);
 		if (IS_ERR(pctl->irqmux[i]))
-- 
2.7.4

[PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
To avoid backward compatibility, the drivers set
the legacy value by default.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/pinctrl/stm32/pinctrl-stm32.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)

diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c b/drivers/pinctrl/stm32/pinctrl-stm32.c
index dfed609..f756232 100644
--- a/drivers/pinctrl/stm32/pinctrl-stm32.c
+++ b/drivers/pinctrl/stm32/pinctrl-stm32.c
@@ -46,6 +46,8 @@
 #define STM32_GPIO_PINS_PER_BANK 16
 #define STM32_GPIO_IRQ_LINE	 16
 
+#define SYSCFG_IRQMUX_MASK GENMASK(3, 0)
+
 #define gpio_range_to_bank(chip) \
 		container_of(chip, struct stm32_gpio_bank, range)
 
@@ -1033,6 +1035,7 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
 	struct device *dev = &pdev->dev;
 	struct regmap *rm;
 	int offset, ret, i;
+	int mask, mask_width;
 
 	parent = of_irq_find_parent(np);
 	if (!parent)
@@ -1052,12 +1055,21 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
 	if (ret)
 		return ret;
 
+	ret = of_property_read_u32_index(np, "st,syscfg", 2, &mask);
+	if (ret)
+		mask = SYSCFG_IRQMUX_MASK;
+
+	mask_width = fls(mask);
+
 	for (i = 0; i < STM32_GPIO_PINS_PER_BANK; i++) {
 		struct reg_field mux;
 
 		mux.reg = offset + (i / 4) * 4;
-		mux.lsb = (i % 4) * 4;
-		mux.msb = mux.lsb + 3;
+		mux.lsb = (i % 4) * mask_width;
+		mux.msb = mux.lsb + mask_width - 1;
+
+		dev_dbg(dev, "irqmux%d: reg:%#x, lsb:%d, msb:%d\n",
+			i, mux.reg, mux.lsb, mux.msb);
 
 		pctl->irqmux[i] = devm_regmap_field_alloc(dev, rm, mux);
 		if (IS_ERR(pctl->irqmux[i]))
-- 
2.7.4

[PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Ludovic Barre]

From: Ludovic Barre <ludovic.barre@st.com>

This patch adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
To avoid backward compatibility, the drivers set
the legacy value by default.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
 drivers/pinctrl/stm32/pinctrl-stm32.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)

diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c b/drivers/pinctrl/stm32/pinctrl-stm32.c
index dfed609..f756232 100644
--- a/drivers/pinctrl/stm32/pinctrl-stm32.c
+++ b/drivers/pinctrl/stm32/pinctrl-stm32.c
@@ -46,6 +46,8 @@
 #define STM32_GPIO_PINS_PER_BANK 16
 #define STM32_GPIO_IRQ_LINE	 16
 
+#define SYSCFG_IRQMUX_MASK GENMASK(3, 0)
+
 #define gpio_range_to_bank(chip) \
 		container_of(chip, struct stm32_gpio_bank, range)
 
@@ -1033,6 +1035,7 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
 	struct device *dev = &pdev->dev;
 	struct regmap *rm;
 	int offset, ret, i;
+	int mask, mask_width;
 
 	parent = of_irq_find_parent(np);
 	if (!parent)
@@ -1052,12 +1055,21 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
 	if (ret)
 		return ret;
 
+	ret = of_property_read_u32_index(np, "st,syscfg", 2, &mask);
+	if (ret)
+		mask = SYSCFG_IRQMUX_MASK;
+
+	mask_width = fls(mask);
+
 	for (i = 0; i < STM32_GPIO_PINS_PER_BANK; i++) {
 		struct reg_field mux;
 
 		mux.reg = offset + (i / 4) * 4;
-		mux.lsb = (i % 4) * 4;
-		mux.msb = mux.lsb + 3;
+		mux.lsb = (i % 4) * mask_width;
+		mux.msb = mux.lsb + mask_width - 1;
+
+		dev_dbg(dev, "irqmux%d: reg:%#x, lsb:%d, msb:%d\n",
+			i, mux.reg, mux.lsb, mux.msb);
 
 		pctl->irqmux[i] = devm_regmap_field_alloc(dev, rm, mux);
 		if (IS_ERR(pctl->irqmux[i]))
-- 
2.7.4

Re: [PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Ludovic BARRE]

Hi

add Rob, I forgotten rob's mail.

On 07/17/2018 11:56 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
> 
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> This parameter is needed if the mask is different of 0xf.
> 
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> ---
>   Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt | 7 ++++---
>   1 file changed, 4 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> index 9a06e1f..4d60119 100644
> --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> @@ -39,9 +39,10 @@ Optional properties:
>    - reset:	  : Reference to the reset controller
>    - interrupt-parent: phandle of the interrupt parent to which the external
>      GPIO interrupts are forwarded to.
> - - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
> -   which includes IRQ mux selection register, and the offset of the IRQ mux
> -   selection register.
> + - st,syscfg: Should be phandle/offset/mask.
> +	-The phandle to the syscon node which includes IRQ mux selection register.
> +	-The offset of the IRQ mux selection register
> +	-The field mask of IRQ mux, needed if different of 0xf.
>    - gpio-ranges: Define a dedicated mapping between a pin-controller and
>      a gpio controller. Format is <&phandle a b c> with:
>   	-(phandle): phandle of pin-controller.
> 

Re: [PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Ludovic BARRE]

Hi

add Rob, I forgotten rob's mail.

On 07/17/2018 11:56 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
> 
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> This parameter is needed if the mask is different of 0xf.
> 
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> ---
>   Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt | 7 ++++---
>   1 file changed, 4 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> index 9a06e1f..4d60119 100644
> --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> @@ -39,9 +39,10 @@ Optional properties:
>    - reset:	  : Reference to the reset controller
>    - interrupt-parent: phandle of the interrupt parent to which the external
>      GPIO interrupts are forwarded to.
> - - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
> -   which includes IRQ mux selection register, and the offset of the IRQ mux
> -   selection register.
> + - st,syscfg: Should be phandle/offset/mask.
> +	-The phandle to the syscon node which includes IRQ mux selection register.
> +	-The offset of the IRQ mux selection register
> +	-The field mask of IRQ mux, needed if different of 0xf.
>    - gpio-ranges: Define a dedicated mapping between a pin-controller and
>      a gpio controller. Format is <&phandle a b c> with:
>   	-(phandle): phandle of pin-controller.
> 

[PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Ludovic BARRE]

Hi

add Rob, I forgotten rob's mail.

On 07/17/2018 11:56 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
> 
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> This parameter is needed if the mask is different of 0xf.
> 
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> ---
>   Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt | 7 ++++---
>   1 file changed, 4 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> index 9a06e1f..4d60119 100644
> --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> @@ -39,9 +39,10 @@ Optional properties:
>    - reset:	  : Reference to the reset controller
>    - interrupt-parent: phandle of the interrupt parent to which the external
>      GPIO interrupts are forwarded to.
> - - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
> -   which includes IRQ mux selection register, and the offset of the IRQ mux
> -   selection register.
> + - st,syscfg: Should be phandle/offset/mask.
> +	-The phandle to the syscon node which includes IRQ mux selection register.
> +	-The offset of the IRQ mux selection register
> +	-The field mask of IRQ mux, needed if different of 0xf.
>    - gpio-ranges: Define a dedicated mapping between a pin-controller and
>      a gpio controller. Format is <&phandle a b c> with:
>   	-(phandle): phandle of pin-controller.
> 

Re: [PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Ludovic BARRE]

Hi

add Rob, I forgotten rob's mail.

On 07/17/2018 11:56 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
> 
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> To avoid backward compatibility, the drivers set
> the legacy value by default.
> 
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> ---
>   drivers/pinctrl/stm32/pinctrl-stm32.c | 16 ++++++++++++++--
>   1 file changed, 14 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c b/drivers/pinctrl/stm32/pinctrl-stm32.c
> index dfed609..f756232 100644
> --- a/drivers/pinctrl/stm32/pinctrl-stm32.c
> +++ b/drivers/pinctrl/stm32/pinctrl-stm32.c
> @@ -46,6 +46,8 @@
>   #define STM32_GPIO_PINS_PER_BANK 16
>   #define STM32_GPIO_IRQ_LINE	 16
>   
> +#define SYSCFG_IRQMUX_MASK GENMASK(3, 0)
> +
>   #define gpio_range_to_bank(chip) \
>   		container_of(chip, struct stm32_gpio_bank, range)
>   
> @@ -1033,6 +1035,7 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
>   	struct device *dev = &pdev->dev;
>   	struct regmap *rm;
>   	int offset, ret, i;
> +	int mask, mask_width;
>   
>   	parent = of_irq_find_parent(np);
>   	if (!parent)
> @@ -1052,12 +1055,21 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
>   	if (ret)
>   		return ret;
>   
> +	ret = of_property_read_u32_index(np, "st,syscfg", 2, &mask);
> +	if (ret)
> +		mask = SYSCFG_IRQMUX_MASK;
> +
> +	mask_width = fls(mask);
> +
>   	for (i = 0; i < STM32_GPIO_PINS_PER_BANK; i++) {
>   		struct reg_field mux;
>   
>   		mux.reg = offset + (i / 4) * 4;
> -		mux.lsb = (i % 4) * 4;
> -		mux.msb = mux.lsb + 3;
> +		mux.lsb = (i % 4) * mask_width;
> +		mux.msb = mux.lsb + mask_width - 1;
> +
> +		dev_dbg(dev, "irqmux%d: reg:%#x, lsb:%d, msb:%d\n",
> +			i, mux.reg, mux.lsb, mux.msb);
>   
>   		pctl->irqmux[i] = devm_regmap_field_alloc(dev, rm, mux);
>   		if (IS_ERR(pctl->irqmux[i]))
> 

Re: [PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Ludovic BARRE]

Hi

add Rob, I forgotten rob's mail.

On 07/17/2018 11:56 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
> 
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> To avoid backward compatibility, the drivers set
> the legacy value by default.
> 
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> ---
>   drivers/pinctrl/stm32/pinctrl-stm32.c | 16 ++++++++++++++--
>   1 file changed, 14 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c b/drivers/pinctrl/stm32/pinctrl-stm32.c
> index dfed609..f756232 100644
> --- a/drivers/pinctrl/stm32/pinctrl-stm32.c
> +++ b/drivers/pinctrl/stm32/pinctrl-stm32.c
> @@ -46,6 +46,8 @@
>   #define STM32_GPIO_PINS_PER_BANK 16
>   #define STM32_GPIO_IRQ_LINE	 16
>   
> +#define SYSCFG_IRQMUX_MASK GENMASK(3, 0)
> +
>   #define gpio_range_to_bank(chip) \
>   		container_of(chip, struct stm32_gpio_bank, range)
>   
> @@ -1033,6 +1035,7 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
>   	struct device *dev = &pdev->dev;
>   	struct regmap *rm;
>   	int offset, ret, i;
> +	int mask, mask_width;
>   
>   	parent = of_irq_find_parent(np);
>   	if (!parent)
> @@ -1052,12 +1055,21 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
>   	if (ret)
>   		return ret;
>   
> +	ret = of_property_read_u32_index(np, "st,syscfg", 2, &mask);
> +	if (ret)
> +		mask = SYSCFG_IRQMUX_MASK;
> +
> +	mask_width = fls(mask);
> +
>   	for (i = 0; i < STM32_GPIO_PINS_PER_BANK; i++) {
>   		struct reg_field mux;
>   
>   		mux.reg = offset + (i / 4) * 4;
> -		mux.lsb = (i % 4) * 4;
> -		mux.msb = mux.lsb + 3;
> +		mux.lsb = (i % 4) * mask_width;
> +		mux.msb = mux.lsb + mask_width - 1;
> +
> +		dev_dbg(dev, "irqmux%d: reg:%#x, lsb:%d, msb:%d\n",
> +			i, mux.reg, mux.lsb, mux.msb);
>   
>   		pctl->irqmux[i] = devm_regmap_field_alloc(dev, rm, mux);
>   		if (IS_ERR(pctl->irqmux[i]))
> 

[PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Ludovic BARRE]

Hi

add Rob, I forgotten rob's mail.

On 07/17/2018 11:56 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
> 
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> To avoid backward compatibility, the drivers set
> the legacy value by default.
> 
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> ---
>   drivers/pinctrl/stm32/pinctrl-stm32.c | 16 ++++++++++++++--
>   1 file changed, 14 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c b/drivers/pinctrl/stm32/pinctrl-stm32.c
> index dfed609..f756232 100644
> --- a/drivers/pinctrl/stm32/pinctrl-stm32.c
> +++ b/drivers/pinctrl/stm32/pinctrl-stm32.c
> @@ -46,6 +46,8 @@
>   #define STM32_GPIO_PINS_PER_BANK 16
>   #define STM32_GPIO_IRQ_LINE	 16
>   
> +#define SYSCFG_IRQMUX_MASK GENMASK(3, 0)
> +
>   #define gpio_range_to_bank(chip) \
>   		container_of(chip, struct stm32_gpio_bank, range)
>   
> @@ -1033,6 +1035,7 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
>   	struct device *dev = &pdev->dev;
>   	struct regmap *rm;
>   	int offset, ret, i;
> +	int mask, mask_width;
>   
>   	parent = of_irq_find_parent(np);
>   	if (!parent)
> @@ -1052,12 +1055,21 @@ static int stm32_pctrl_dt_setup_irq(struct platform_device *pdev,
>   	if (ret)
>   		return ret;
>   
> +	ret = of_property_read_u32_index(np, "st,syscfg", 2, &mask);
> +	if (ret)
> +		mask = SYSCFG_IRQMUX_MASK;
> +
> +	mask_width = fls(mask);
> +
>   	for (i = 0; i < STM32_GPIO_PINS_PER_BANK; i++) {
>   		struct reg_field mux;
>   
>   		mux.reg = offset + (i / 4) * 4;
> -		mux.lsb = (i % 4) * 4;
> -		mux.msb = mux.lsb + 3;
> +		mux.lsb = (i % 4) * mask_width;
> +		mux.msb = mux.lsb + mask_width - 1;
> +
> +		dev_dbg(dev, "irqmux%d: reg:%#x, lsb:%d, msb:%d\n",
> +			i, mux.reg, mux.lsb, mux.msb);
>   
>   		pctl->irqmux[i] = devm_regmap_field_alloc(dev, rm, mux);
>   		if (IS_ERR(pctl->irqmux[i]))
> 

Re: [PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Alexandre Torgue]

On 07/17/2018 11:56 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
> 
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> This parameter is needed if the mask is different of 0xf.
> 
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> ---
>   Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt | 7 ++++---
>   1 file changed, 4 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> index 9a06e1f..4d60119 100644
> --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> @@ -39,9 +39,10 @@ Optional properties:
>    - reset:	  : Reference to the reset controller
>    - interrupt-parent: phandle of the interrupt parent to which the external
>      GPIO interrupts are forwarded to.
> - - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
> -   which includes IRQ mux selection register, and the offset of the IRQ mux
> -   selection register.
> + - st,syscfg: Should be phandle/offset/mask.
> +	-The phandle to the syscon node which includes IRQ mux selection register.
> +	-The offset of the IRQ mux selection register
> +	-The field mask of IRQ mux, needed if different of 0xf.
>    - gpio-ranges: Define a dedicated mapping between a pin-controller and
>      a gpio controller. Format is <&phandle a b c> with:
>   	-(phandle): phandle of pin-controller.
> 
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>

Re: [PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Alexandre Torgue]

On 07/17/2018 11:56 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
> 
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> This parameter is needed if the mask is different of 0xf.
> 
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> ---
>   Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt | 7 ++++---
>   1 file changed, 4 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> index 9a06e1f..4d60119 100644
> --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> @@ -39,9 +39,10 @@ Optional properties:
>    - reset:	  : Reference to the reset controller
>    - interrupt-parent: phandle of the interrupt parent to which the external
>      GPIO interrupts are forwarded to.
> - - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
> -   which includes IRQ mux selection register, and the offset of the IRQ mux
> -   selection register.
> + - st,syscfg: Should be phandle/offset/mask.
> +	-The phandle to the syscon node which includes IRQ mux selection register.
> +	-The offset of the IRQ mux selection register
> +	-The field mask of IRQ mux, needed if different of 0xf.
>    - gpio-ranges: Define a dedicated mapping between a pin-controller and
>      a gpio controller. Format is <&phandle a b c> with:
>   	-(phandle): phandle of pin-controller.
> 
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>

[PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Alexandre Torgue]

On 07/17/2018 11:56 AM, Ludovic Barre wrote:
> From: Ludovic Barre <ludovic.barre@st.com>
> 
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> This parameter is needed if the mask is different of 0xf.
> 
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
> ---
>   Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt | 7 ++++---
>   1 file changed, 4 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> index 9a06e1f..4d60119 100644
> --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt
> @@ -39,9 +39,10 @@ Optional properties:
>    - reset:	  : Reference to the reset controller
>    - interrupt-parent: phandle of the interrupt parent to which the external
>      GPIO interrupts are forwarded to.
> - - st,syscfg: Should be phandle/offset pair. The phandle to the syscon node
> -   which includes IRQ mux selection register, and the offset of the IRQ mux
> -   selection register.
> + - st,syscfg: Should be phandle/offset/mask.
> +	-The phandle to the syscon node which includes IRQ mux selection register.
> +	-The offset of the IRQ mux selection register
> +	-The field mask of IRQ mux, needed if different of 0xf.
>    - gpio-ranges: Define a dedicated mapping between a pin-controller and
>      a gpio controller. Format is <&phandle a b c> with:
>   	-(phandle): phandle of pin-controller.
> 
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>

Re: [PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Alexandre Torgue]

On 07/17/2018 03:11 PM, Ludovic BARRE wrote:
> Hi
> 
> add Rob, I forgotten rob's mail.
> 
> On 07/17/2018 11:56 AM, Ludovic Barre wrote:
>> From: Ludovic Barre <ludovic.barre@st.com>
>>
>> This patch adds mask parameter to define IRQ mux field.
>> This field could vary depend of IRQ mux selection register.
>> To avoid backward compatibility, the drivers set
>> the legacy value by default.
>>
>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>

Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>


>> ---
>>   drivers/pinctrl/stm32/pinctrl-stm32.c | 16 ++++++++++++++--
>>   1 file changed, 14 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c 
>> b/drivers/pinctrl/stm32/pinctrl-stm32.c
>> index dfed609..f756232 100644
>> --- a/drivers/pinctrl/stm32/pinctrl-stm32.c
>> +++ b/drivers/pinctrl/stm32/pinctrl-stm32.c
>> @@ -46,6 +46,8 @@
>>   #define STM32_GPIO_PINS_PER_BANK 16
>>   #define STM32_GPIO_IRQ_LINE     16
>> +#define SYSCFG_IRQMUX_MASK GENMASK(3, 0)
>> +
>>   #define gpio_range_to_bank(chip) \
>>           container_of(chip, struct stm32_gpio_bank, range)
>> @@ -1033,6 +1035,7 @@ static int stm32_pctrl_dt_setup_irq(struct 
>> platform_device *pdev,
>>       struct device *dev = &pdev->dev;
>>       struct regmap *rm;
>>       int offset, ret, i;
>> +    int mask, mask_width;
>>       parent = of_irq_find_parent(np);
>>       if (!parent)
>> @@ -1052,12 +1055,21 @@ static int stm32_pctrl_dt_setup_irq(struct 
>> platform_device *pdev,
>>       if (ret)
>>           return ret;
>> +    ret = of_property_read_u32_index(np, "st,syscfg", 2, &mask);
>> +    if (ret)
>> +        mask = SYSCFG_IRQMUX_MASK;
>> +
>> +    mask_width = fls(mask);
>> +
>>       for (i = 0; i < STM32_GPIO_PINS_PER_BANK; i++) {
>>           struct reg_field mux;
>>           mux.reg = offset + (i / 4) * 4;
>> -        mux.lsb = (i % 4) * 4;
>> -        mux.msb = mux.lsb + 3;
>> +        mux.lsb = (i % 4) * mask_width;
>> +        mux.msb = mux.lsb + mask_width - 1;
>> +
>> +        dev_dbg(dev, "irqmux%d: reg:%#x, lsb:%d, msb:%d\n",
>> +            i, mux.reg, mux.lsb, mux.msb);
>>           pctl->irqmux[i] = devm_regmap_field_alloc(dev, rm, mux);
>>           if (IS_ERR(pctl->irqmux[i]))
>>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Alexandre Torgue]

On 07/17/2018 03:11 PM, Ludovic BARRE wrote:
> Hi
> 
> add Rob, I forgotten rob's mail.
> 
> On 07/17/2018 11:56 AM, Ludovic Barre wrote:
>> From: Ludovic Barre <ludovic.barre@st.com>
>>
>> This patch adds mask parameter to define IRQ mux field.
>> This field could vary depend of IRQ mux selection register.
>> To avoid backward compatibility, the drivers set
>> the legacy value by default.
>>
>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>

Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>


>> ---
>>   drivers/pinctrl/stm32/pinctrl-stm32.c | 16 ++++++++++++++--
>>   1 file changed, 14 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c 
>> b/drivers/pinctrl/stm32/pinctrl-stm32.c
>> index dfed609..f756232 100644
>> --- a/drivers/pinctrl/stm32/pinctrl-stm32.c
>> +++ b/drivers/pinctrl/stm32/pinctrl-stm32.c
>> @@ -46,6 +46,8 @@
>>   #define STM32_GPIO_PINS_PER_BANK 16
>>   #define STM32_GPIO_IRQ_LINE     16
>> +#define SYSCFG_IRQMUX_MASK GENMASK(3, 0)
>> +
>>   #define gpio_range_to_bank(chip) \
>>           container_of(chip, struct stm32_gpio_bank, range)
>> @@ -1033,6 +1035,7 @@ static int stm32_pctrl_dt_setup_irq(struct 
>> platform_device *pdev,
>>       struct device *dev = &pdev->dev;
>>       struct regmap *rm;
>>       int offset, ret, i;
>> +    int mask, mask_width;
>>       parent = of_irq_find_parent(np);
>>       if (!parent)
>> @@ -1052,12 +1055,21 @@ static int stm32_pctrl_dt_setup_irq(struct 
>> platform_device *pdev,
>>       if (ret)
>>           return ret;
>> +    ret = of_property_read_u32_index(np, "st,syscfg", 2, &mask);
>> +    if (ret)
>> +        mask = SYSCFG_IRQMUX_MASK;
>> +
>> +    mask_width = fls(mask);
>> +
>>       for (i = 0; i < STM32_GPIO_PINS_PER_BANK; i++) {
>>           struct reg_field mux;
>>           mux.reg = offset + (i / 4) * 4;
>> -        mux.lsb = (i % 4) * 4;
>> -        mux.msb = mux.lsb + 3;
>> +        mux.lsb = (i % 4) * mask_width;
>> +        mux.msb = mux.lsb + mask_width - 1;
>> +
>> +        dev_dbg(dev, "irqmux%d: reg:%#x, lsb:%d, msb:%d\n",
>> +            i, mux.reg, mux.lsb, mux.msb);
>>           pctl->irqmux[i] = devm_regmap_field_alloc(dev, rm, mux);
>>           if (IS_ERR(pctl->irqmux[i]))
>>

[PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Alexandre Torgue]

On 07/17/2018 03:11 PM, Ludovic BARRE wrote:
> Hi
> 
> add Rob, I forgotten rob's mail.
> 
> On 07/17/2018 11:56 AM, Ludovic Barre wrote:
>> From: Ludovic Barre <ludovic.barre@st.com>
>>
>> This patch adds mask parameter to define IRQ mux field.
>> This field could vary depend of IRQ mux selection register.
>> To avoid backward compatibility, the drivers set
>> the legacy value by default.
>>
>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>

Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>


>> ---
>> ? drivers/pinctrl/stm32/pinctrl-stm32.c | 16 ++++++++++++++--
>> ? 1 file changed, 14 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/pinctrl/stm32/pinctrl-stm32.c 
>> b/drivers/pinctrl/stm32/pinctrl-stm32.c
>> index dfed609..f756232 100644
>> --- a/drivers/pinctrl/stm32/pinctrl-stm32.c
>> +++ b/drivers/pinctrl/stm32/pinctrl-stm32.c
>> @@ -46,6 +46,8 @@
>> ? #define STM32_GPIO_PINS_PER_BANK 16
>> ? #define STM32_GPIO_IRQ_LINE???? 16
>> +#define SYSCFG_IRQMUX_MASK GENMASK(3, 0)
>> +
>> ? #define gpio_range_to_bank(chip) \
>> ????????? container_of(chip, struct stm32_gpio_bank, range)
>> @@ -1033,6 +1035,7 @@ static int stm32_pctrl_dt_setup_irq(struct 
>> platform_device *pdev,
>> ????? struct device *dev = &pdev->dev;
>> ????? struct regmap *rm;
>> ????? int offset, ret, i;
>> +??? int mask, mask_width;
>> ????? parent = of_irq_find_parent(np);
>> ????? if (!parent)
>> @@ -1052,12 +1055,21 @@ static int stm32_pctrl_dt_setup_irq(struct 
>> platform_device *pdev,
>> ????? if (ret)
>> ????????? return ret;
>> +??? ret = of_property_read_u32_index(np, "st,syscfg", 2, &mask);
>> +??? if (ret)
>> +??????? mask = SYSCFG_IRQMUX_MASK;
>> +
>> +??? mask_width = fls(mask);
>> +
>> ????? for (i = 0; i < STM32_GPIO_PINS_PER_BANK; i++) {
>> ????????? struct reg_field mux;
>> ????????? mux.reg = offset + (i / 4) * 4;
>> -??????? mux.lsb = (i % 4) * 4;
>> -??????? mux.msb = mux.lsb + 3;
>> +??????? mux.lsb = (i % 4) * mask_width;
>> +??????? mux.msb = mux.lsb + mask_width - 1;
>> +
>> +??????? dev_dbg(dev, "irqmux%d: reg:%#x, lsb:%d, msb:%d\n",
>> +??????????? i, mux.reg, mux.lsb, mux.msb);
>> ????????? pctl->irqmux[i] = devm_regmap_field_alloc(dev, rm, mux);
>> ????????? if (IS_ERR(pctl->irqmux[i]))
>>

Re: [PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Linus Walleij]

On Tue, Jul 17, 2018 at 11:56 AM Ludovic Barre <ludovic.Barre@st.com> wrote:

> From: Ludovic Barre <ludovic.barre@st.com>
>
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> This parameter is needed if the mask is different of 0xf.
>
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>

Patch applied with Alexandre's ACK.

Yours,
Linus Walleij

[PATCH 1/2] dt-bindings: pinctrl: add syscfg mask parameter

[Linus Walleij]

On Tue, Jul 17, 2018 at 11:56 AM Ludovic Barre <ludovic.Barre@st.com> wrote:

> From: Ludovic Barre <ludovic.barre@st.com>
>
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> This parameter is needed if the mask is different of 0xf.
>
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>

Patch applied with Alexandre's ACK.

Yours,
Linus Walleij

Re: [PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Linus Walleij]

On Tue, Jul 17, 2018 at 11:56 AM Ludovic Barre <ludovic.Barre@st.com> wrote:

> From: Ludovic Barre <ludovic.barre@st.com>
>
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> To avoid backward compatibility, the drivers set
> the legacy value by default.
>
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>

Patch applied with Alexandre's ACK.

Yours,
Linus Walleij

[PATCH 2/2] pinctrl: stm32: add syscfg mask parameter

[Linus Walleij]

On Tue, Jul 17, 2018 at 11:56 AM Ludovic Barre <ludovic.Barre@st.com> wrote:

> From: Ludovic Barre <ludovic.barre@st.com>
>
> This patch adds mask parameter to define IRQ mux field.
> This field could vary depend of IRQ mux selection register.
> To avoid backward compatibility, the drivers set
> the legacy value by default.
>
> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>

Patch applied with Alexandre's ACK.

Yours,
Linus Walleij