* [PATCH 0/4] Add UniPhier USB3 controller and USB2 phy nodes
@ 2018-10-02 11:11 ` Kunihiko Hayashi
0 siblings, 0 replies; 14+ messages in thread
From: Kunihiko Hayashi @ 2018-10-02 11:11 UTC (permalink / raw)
To: Masahiro Yamada, linux-arm-kernel
Cc: Mark Rutland, devicetree, Masami Hiramatsu, Kunihiko Hayashi,
Jassi Brar, Rob Herring
This series adds the DT nodes for USB3 controllers and USB2 phys
implemented on UniPhier SoCs.
Kunihiko Hayashi (4):
ARM: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 phy nodes
arm64: dts: uniphier: Add USB3 controller nodes
arm64: dts: uniphier: Add USB2 phy nodes
arch/arm/boot/dts/uniphier-pro4-ace.dts | 8 +
arch/arm/boot/dts/uniphier-pro4-ref.dts | 8 +
arch/arm/boot/dts/uniphier-pro4.dtsi | 127 +++++++++++
arch/arm/boot/dts/uniphier-pxs2-gentil.dts | 8 +
arch/arm/boot/dts/uniphier-pxs2-vodka.dts | 4 +
arch/arm/boot/dts/uniphier-pxs2.dtsi | 180 ++++++++++++++++
arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi | 27 +++
.../boot/dts/socionext/uniphier-ld20-global.dts | 4 +
.../arm64/boot/dts/socionext/uniphier-ld20-ref.dts | 4 +
arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi | 194 +++++++++++++++++
.../arm64/boot/dts/socionext/uniphier-pxs3-ref.dts | 8 +
arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi | 240 +++++++++++++++++++++
12 files changed, 812 insertions(+)
--
2.7.4
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 0/4] Add UniPhier USB3 controller and USB2 phy nodes
@ 2018-10-02 11:11 ` Kunihiko Hayashi
0 siblings, 0 replies; 14+ messages in thread
From: Kunihiko Hayashi @ 2018-10-02 11:11 UTC (permalink / raw)
To: linux-arm-kernel
This series adds the DT nodes for USB3 controllers and USB2 phys
implemented on UniPhier SoCs.
Kunihiko Hayashi (4):
ARM: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 phy nodes
arm64: dts: uniphier: Add USB3 controller nodes
arm64: dts: uniphier: Add USB2 phy nodes
arch/arm/boot/dts/uniphier-pro4-ace.dts | 8 +
arch/arm/boot/dts/uniphier-pro4-ref.dts | 8 +
arch/arm/boot/dts/uniphier-pro4.dtsi | 127 +++++++++++
arch/arm/boot/dts/uniphier-pxs2-gentil.dts | 8 +
arch/arm/boot/dts/uniphier-pxs2-vodka.dts | 4 +
arch/arm/boot/dts/uniphier-pxs2.dtsi | 180 ++++++++++++++++
arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi | 27 +++
.../boot/dts/socionext/uniphier-ld20-global.dts | 4 +
.../arm64/boot/dts/socionext/uniphier-ld20-ref.dts | 4 +
arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi | 194 +++++++++++++++++
.../arm64/boot/dts/socionext/uniphier-pxs3-ref.dts | 8 +
arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi | 240 +++++++++++++++++++++
12 files changed, 812 insertions(+)
--
2.7.4
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/4] ARM: dts: uniphier: Add USB3 controller nodes
2018-10-02 11:11 ` Kunihiko Hayashi
@ 2018-10-02 11:11 ` Kunihiko Hayashi
-1 siblings, 0 replies; 14+ messages in thread
From: Kunihiko Hayashi @ 2018-10-02 11:11 UTC (permalink / raw)
To: Masahiro Yamada, linux-arm-kernel
Cc: Mark Rutland, devicetree, Masami Hiramatsu, Kunihiko Hayashi,
Jassi Brar, Rob Herring
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for Pro4, PXs2 and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
arch/arm/boot/dts/uniphier-pro4-ace.dts | 8 ++
arch/arm/boot/dts/uniphier-pro4-ref.dts | 8 ++
arch/arm/boot/dts/uniphier-pro4.dtsi | 94 +++++++++++++++
arch/arm/boot/dts/uniphier-pxs2-gentil.dts | 8 ++
arch/arm/boot/dts/uniphier-pxs2-vodka.dts | 4 +
arch/arm/boot/dts/uniphier-pxs2.dtsi | 180 +++++++++++++++++++++++++++++
6 files changed, 302 insertions(+)
diff --git a/arch/arm/boot/dts/uniphier-pro4-ace.dts b/arch/arm/boot/dts/uniphier-pro4-ace.dts
index db1b089..c6ac72c 100644
--- a/arch/arm/boot/dts/uniphier-pro4-ace.dts
+++ b/arch/arm/boot/dts/uniphier-pro4-ace.dts
@@ -68,6 +68,14 @@
status = "okay";
};
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
&usb2 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/uniphier-pro4-ref.dts b/arch/arm/boot/dts/uniphier-pro4-ref.dts
index efb0849..0debf5a 100644
--- a/arch/arm/boot/dts/uniphier-pro4-ref.dts
+++ b/arch/arm/boot/dts/uniphier-pro4-ref.dts
@@ -65,6 +65,14 @@
status = "okay";
};
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
&usb2 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/uniphier-pro4.dtsi b/arch/arm/boot/dts/uniphier-pro4.dtsi
index 49539f0..b994494 100644
--- a/arch/arm/boot/dts/uniphier-pro4.dtsi
+++ b/arch/arm/boot/dts/uniphier-pro4.dtsi
@@ -386,6 +386,100 @@
};
};
+ usb0: usb@65a00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65a00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 134 4>, <0 135 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
+ resets = <&usb0_rst 4>;
+ phys = <&usb0_ssphy>;
+ dr_mode = "host";
+ };
+
+ usb-glue@65b00000 {
+ compatible = "socionext,uniphier-pro4-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65b00000 0x100>;
+
+ usb0_vbus: regulator@0 {
+ compatible = "socionext,uniphier-pro4-usb3-regulator";
+ reg = <0 0x10>;
+ clock-names = "gio", "link";
+ clocks = <&sys_clk 12>, <&sys_clk 14>;
+ reset-names = "gio", "link";
+ resets = <&sys_rst 12>, <&sys_rst 14>;
+ };
+
+ usb0_ssphy: ss-phy@10 {
+ compatible = "socionext,uniphier-pro4-usb3-ssphy";
+ reg = <0x10 0x10>;
+ #phy-cells = <0>;
+ clock-names = "gio", "link";
+ clocks = <&sys_clk 12>, <&sys_clk 14>;
+ reset-names = "gio", "link";
+ resets = <&sys_rst 12>, <&sys_rst 14>;
+ vbus-supply = <&usb0_vbus>;
+ };
+
+ usb0_rst: reset@40 {
+ compatible = "socionext,uniphier-pro4-usb3-reset";
+ reg = <0x40 0x4>;
+ #reset-cells = <1>;
+ clock-names = "gio", "link";
+ clocks = <&sys_clk 12>, <&sys_clk 14>;
+ reset-names = "gio", "link";
+ resets = <&sys_rst 12>, <&sys_rst 14>;
+ };
+ };
+
+ usb1: usb@65c00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65c00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 137 4>, <0 138 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
+ resets = <&usb1_rst 4>;
+ dr_mode = "host";
+ };
+
+ usb-glue@65d00000 {
+ compatible = "socionext,uniphier-pro4-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65d00000 0x100>;
+
+ usb1_vbus: regulator@0 {
+ compatible = "socionext,uniphier-pro4-usb3-regulator";
+ reg = <0 0x10>;
+ clock-names = "gio", "link";
+ clocks = <&sys_clk 12>, <&sys_clk 15>;
+ reset-names = "gio", "link";
+ resets = <&sys_rst 12>, <&sys_rst 15>;
+ };
+
+ usb1_rst: reset@40 {
+ compatible = "socionext,uniphier-pro4-usb3-reset";
+ reg = <0x40 0x4>;
+ #reset-cells = <1>;
+ clock-names = "gio", "link";
+ clocks = <&sys_clk 12>, <&sys_clk 15>;
+ reset-names = "gio", "link";
+ resets = <&sys_rst 12>, <&sys_rst 15>;
+ };
+ };
+
nand: nand@68000000 {
compatible = "socionext,uniphier-denali-nand-v5a";
status = "disabled";
diff --git a/arch/arm/boot/dts/uniphier-pxs2-gentil.dts b/arch/arm/boot/dts/uniphier-pxs2-gentil.dts
index bed26b8..095774c 100644
--- a/arch/arm/boot/dts/uniphier-pxs2-gentil.dts
+++ b/arch/arm/boot/dts/uniphier-pxs2-gentil.dts
@@ -86,3 +86,11 @@
reg = <1>;
};
};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pxs2-vodka.dts b/arch/arm/boot/dts/uniphier-pxs2-vodka.dts
index b13d2d1..03dc63f 100644
--- a/arch/arm/boot/dts/uniphier-pxs2-vodka.dts
+++ b/arch/arm/boot/dts/uniphier-pxs2-vodka.dts
@@ -87,3 +87,7 @@
reg = <1>;
};
};
+
+&usb0 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pxs2.dtsi b/arch/arm/boot/dts/uniphier-pxs2.dtsi
index e2d1a22..2c93cc7 100644
--- a/arch/arm/boot/dts/uniphier-pxs2.dtsi
+++ b/arch/arm/boot/dts/uniphier-pxs2.dtsi
@@ -523,6 +523,186 @@
};
};
+ usb0: usb@65a00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65a00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 134 4>, <0 135 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 14>, <&sys_clk 14>, <&sys_clk 14>;
+ resets = <&usb0_rst 15>;
+ phys = <&usb0_hsphy0>, <&usb0_hsphy1>,
+ <&usb0_ssphy0>, <&usb0_ssphy1>;
+ dr_mode = "host";
+ };
+
+ usb-glue@65b00000 {
+ compatible = "socionext,uniphier-pxs2-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65b00000 0x400>;
+
+ usb0_rst: reset@0 {
+ compatible = "socionext,uniphier-pxs2-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb0_vbus0: regulator@100 {
+ compatible = "socionext,uniphier-pxs2-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb0_vbus1: regulator@110 {
+ compatible = "socionext,uniphier-pxs2-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb0_hsphy0: hs-phy@200 {
+ compatible = "socionext,uniphier-pxs2-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 16>;
+ vbus-supply = <&usb0_vbus0>;
+ };
+
+ usb0_hsphy1: hs-phy@210 {
+ compatible = "socionext,uniphier-pxs2-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 16>;
+ vbus-supply = <&usb0_vbus1>;
+ };
+
+ usb0_ssphy0: ss-phy@300 {
+ compatible = "socionext,uniphier-pxs2-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 17>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 17>;
+ vbus-supply = <&usb0_vbus0>;
+ };
+
+ usb0_ssphy1: ss-phy@310 {
+ compatible = "socionext,uniphier-pxs2-usb3-ssphy";
+ reg = <0x310 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 18>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 18>;
+ vbus-supply = <&usb0_vbus1>;
+ };
+ };
+
+ usb1: usb@65c00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65c00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 137 4>, <0 138 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 15>, <&sys_clk 15>, <&sys_clk 15>;
+ resets = <&usb1_rst 15>;
+ phys = <&usb1_hsphy0>, <&usb1_hsphy1>, <&usb1_ssphy0>;
+ dr_mode = "host";
+ };
+
+ usb-glue@65d00000 {
+ compatible = "socionext,uniphier-pxs2-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65d00000 0x400>;
+
+ usb1_rst: reset@0 {
+ compatible = "socionext,uniphier-pxs2-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 15>;
+ reset-names = "link";
+ resets = <&sys_rst 15>;
+ };
+
+ usb1_vbus0: regulator@100 {
+ compatible = "socionext,uniphier-pxs2-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 15>;
+ reset-names = "link";
+ resets = <&sys_rst 15>;
+ };
+
+ usb1_vbus1: regulator@110 {
+ compatible = "socionext,uniphier-pxs2-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 15>;
+ reset-names = "link";
+ resets = <&sys_rst 15>;
+ };
+
+ usb1_hsphy0: hs-phy@200 {
+ compatible = "socionext,uniphier-pxs2-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 15>, <&sys_clk 20>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 15>, <&sys_rst 20>;
+ vbus-supply = <&usb1_vbus0>;
+ };
+
+ usb1_hsphy1: hs-phy@210 {
+ compatible = "socionext,uniphier-pxs2-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 15>, <&sys_clk 20>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 15>, <&sys_rst 20>;
+ vbus-supply = <&usb1_vbus1>;
+ };
+
+ usb1_ssphy0: ss-phy@300 {
+ compatible = "socionext,uniphier-pxs2-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 15>, <&sys_clk 21>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 15>, <&sys_rst 21>;
+ vbus-supply = <&usb1_vbus0>;
+ };
+ };
+
nand: nand@68000000 {
compatible = "socionext,uniphier-denali-nand-v5b";
status = "disabled";
--
2.7.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 1/4] ARM: dts: uniphier: Add USB3 controller nodes
@ 2018-10-02 11:11 ` Kunihiko Hayashi
0 siblings, 0 replies; 14+ messages in thread
From: Kunihiko Hayashi @ 2018-10-02 11:11 UTC (permalink / raw)
To: linux-arm-kernel
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for Pro4, PXs2 and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
arch/arm/boot/dts/uniphier-pro4-ace.dts | 8 ++
arch/arm/boot/dts/uniphier-pro4-ref.dts | 8 ++
arch/arm/boot/dts/uniphier-pro4.dtsi | 94 +++++++++++++++
arch/arm/boot/dts/uniphier-pxs2-gentil.dts | 8 ++
arch/arm/boot/dts/uniphier-pxs2-vodka.dts | 4 +
arch/arm/boot/dts/uniphier-pxs2.dtsi | 180 +++++++++++++++++++++++++++++
6 files changed, 302 insertions(+)
diff --git a/arch/arm/boot/dts/uniphier-pro4-ace.dts b/arch/arm/boot/dts/uniphier-pro4-ace.dts
index db1b089..c6ac72c 100644
--- a/arch/arm/boot/dts/uniphier-pro4-ace.dts
+++ b/arch/arm/boot/dts/uniphier-pro4-ace.dts
@@ -68,6 +68,14 @@
status = "okay";
};
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
&usb2 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/uniphier-pro4-ref.dts b/arch/arm/boot/dts/uniphier-pro4-ref.dts
index efb0849..0debf5a 100644
--- a/arch/arm/boot/dts/uniphier-pro4-ref.dts
+++ b/arch/arm/boot/dts/uniphier-pro4-ref.dts
@@ -65,6 +65,14 @@
status = "okay";
};
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
&usb2 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/uniphier-pro4.dtsi b/arch/arm/boot/dts/uniphier-pro4.dtsi
index 49539f0..b994494 100644
--- a/arch/arm/boot/dts/uniphier-pro4.dtsi
+++ b/arch/arm/boot/dts/uniphier-pro4.dtsi
@@ -386,6 +386,100 @@
};
};
+ usb0: usb at 65a00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65a00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 134 4>, <0 135 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
+ resets = <&usb0_rst 4>;
+ phys = <&usb0_ssphy>;
+ dr_mode = "host";
+ };
+
+ usb-glue at 65b00000 {
+ compatible = "socionext,uniphier-pro4-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65b00000 0x100>;
+
+ usb0_vbus: regulator at 0 {
+ compatible = "socionext,uniphier-pro4-usb3-regulator";
+ reg = <0 0x10>;
+ clock-names = "gio", "link";
+ clocks = <&sys_clk 12>, <&sys_clk 14>;
+ reset-names = "gio", "link";
+ resets = <&sys_rst 12>, <&sys_rst 14>;
+ };
+
+ usb0_ssphy: ss-phy at 10 {
+ compatible = "socionext,uniphier-pro4-usb3-ssphy";
+ reg = <0x10 0x10>;
+ #phy-cells = <0>;
+ clock-names = "gio", "link";
+ clocks = <&sys_clk 12>, <&sys_clk 14>;
+ reset-names = "gio", "link";
+ resets = <&sys_rst 12>, <&sys_rst 14>;
+ vbus-supply = <&usb0_vbus>;
+ };
+
+ usb0_rst: reset at 40 {
+ compatible = "socionext,uniphier-pro4-usb3-reset";
+ reg = <0x40 0x4>;
+ #reset-cells = <1>;
+ clock-names = "gio", "link";
+ clocks = <&sys_clk 12>, <&sys_clk 14>;
+ reset-names = "gio", "link";
+ resets = <&sys_rst 12>, <&sys_rst 14>;
+ };
+ };
+
+ usb1: usb at 65c00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65c00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 137 4>, <0 138 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
+ resets = <&usb1_rst 4>;
+ dr_mode = "host";
+ };
+
+ usb-glue at 65d00000 {
+ compatible = "socionext,uniphier-pro4-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65d00000 0x100>;
+
+ usb1_vbus: regulator at 0 {
+ compatible = "socionext,uniphier-pro4-usb3-regulator";
+ reg = <0 0x10>;
+ clock-names = "gio", "link";
+ clocks = <&sys_clk 12>, <&sys_clk 15>;
+ reset-names = "gio", "link";
+ resets = <&sys_rst 12>, <&sys_rst 15>;
+ };
+
+ usb1_rst: reset at 40 {
+ compatible = "socionext,uniphier-pro4-usb3-reset";
+ reg = <0x40 0x4>;
+ #reset-cells = <1>;
+ clock-names = "gio", "link";
+ clocks = <&sys_clk 12>, <&sys_clk 15>;
+ reset-names = "gio", "link";
+ resets = <&sys_rst 12>, <&sys_rst 15>;
+ };
+ };
+
nand: nand at 68000000 {
compatible = "socionext,uniphier-denali-nand-v5a";
status = "disabled";
diff --git a/arch/arm/boot/dts/uniphier-pxs2-gentil.dts b/arch/arm/boot/dts/uniphier-pxs2-gentil.dts
index bed26b8..095774c 100644
--- a/arch/arm/boot/dts/uniphier-pxs2-gentil.dts
+++ b/arch/arm/boot/dts/uniphier-pxs2-gentil.dts
@@ -86,3 +86,11 @@
reg = <1>;
};
};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pxs2-vodka.dts b/arch/arm/boot/dts/uniphier-pxs2-vodka.dts
index b13d2d1..03dc63f 100644
--- a/arch/arm/boot/dts/uniphier-pxs2-vodka.dts
+++ b/arch/arm/boot/dts/uniphier-pxs2-vodka.dts
@@ -87,3 +87,7 @@
reg = <1>;
};
};
+
+&usb0 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pxs2.dtsi b/arch/arm/boot/dts/uniphier-pxs2.dtsi
index e2d1a22..2c93cc7 100644
--- a/arch/arm/boot/dts/uniphier-pxs2.dtsi
+++ b/arch/arm/boot/dts/uniphier-pxs2.dtsi
@@ -523,6 +523,186 @@
};
};
+ usb0: usb at 65a00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65a00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 134 4>, <0 135 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 14>, <&sys_clk 14>, <&sys_clk 14>;
+ resets = <&usb0_rst 15>;
+ phys = <&usb0_hsphy0>, <&usb0_hsphy1>,
+ <&usb0_ssphy0>, <&usb0_ssphy1>;
+ dr_mode = "host";
+ };
+
+ usb-glue at 65b00000 {
+ compatible = "socionext,uniphier-pxs2-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65b00000 0x400>;
+
+ usb0_rst: reset at 0 {
+ compatible = "socionext,uniphier-pxs2-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb0_vbus0: regulator at 100 {
+ compatible = "socionext,uniphier-pxs2-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb0_vbus1: regulator at 110 {
+ compatible = "socionext,uniphier-pxs2-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb0_hsphy0: hs-phy at 200 {
+ compatible = "socionext,uniphier-pxs2-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 16>;
+ vbus-supply = <&usb0_vbus0>;
+ };
+
+ usb0_hsphy1: hs-phy at 210 {
+ compatible = "socionext,uniphier-pxs2-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 16>;
+ vbus-supply = <&usb0_vbus1>;
+ };
+
+ usb0_ssphy0: ss-phy at 300 {
+ compatible = "socionext,uniphier-pxs2-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 17>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 17>;
+ vbus-supply = <&usb0_vbus0>;
+ };
+
+ usb0_ssphy1: ss-phy at 310 {
+ compatible = "socionext,uniphier-pxs2-usb3-ssphy";
+ reg = <0x310 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 18>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 18>;
+ vbus-supply = <&usb0_vbus1>;
+ };
+ };
+
+ usb1: usb at 65c00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65c00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 137 4>, <0 138 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 15>, <&sys_clk 15>, <&sys_clk 15>;
+ resets = <&usb1_rst 15>;
+ phys = <&usb1_hsphy0>, <&usb1_hsphy1>, <&usb1_ssphy0>;
+ dr_mode = "host";
+ };
+
+ usb-glue at 65d00000 {
+ compatible = "socionext,uniphier-pxs2-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65d00000 0x400>;
+
+ usb1_rst: reset at 0 {
+ compatible = "socionext,uniphier-pxs2-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 15>;
+ reset-names = "link";
+ resets = <&sys_rst 15>;
+ };
+
+ usb1_vbus0: regulator at 100 {
+ compatible = "socionext,uniphier-pxs2-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 15>;
+ reset-names = "link";
+ resets = <&sys_rst 15>;
+ };
+
+ usb1_vbus1: regulator at 110 {
+ compatible = "socionext,uniphier-pxs2-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 15>;
+ reset-names = "link";
+ resets = <&sys_rst 15>;
+ };
+
+ usb1_hsphy0: hs-phy at 200 {
+ compatible = "socionext,uniphier-pxs2-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 15>, <&sys_clk 20>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 15>, <&sys_rst 20>;
+ vbus-supply = <&usb1_vbus0>;
+ };
+
+ usb1_hsphy1: hs-phy at 210 {
+ compatible = "socionext,uniphier-pxs2-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 15>, <&sys_clk 20>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 15>, <&sys_rst 20>;
+ vbus-supply = <&usb1_vbus1>;
+ };
+
+ usb1_ssphy0: ss-phy at 300 {
+ compatible = "socionext,uniphier-pxs2-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 15>, <&sys_clk 21>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 15>, <&sys_rst 21>;
+ vbus-supply = <&usb1_vbus0>;
+ };
+ };
+
nand: nand at 68000000 {
compatible = "socionext,uniphier-denali-nand-v5b";
status = "disabled";
--
2.7.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/4] ARM: dts: uniphier: Add USB2 phy nodes
2018-10-02 11:11 ` Kunihiko Hayashi
@ 2018-10-02 11:12 ` Kunihiko Hayashi
-1 siblings, 0 replies; 14+ messages in thread
From: Kunihiko Hayashi @ 2018-10-02 11:12 UTC (permalink / raw)
To: Masahiro Yamada, linux-arm-kernel
Cc: Mark Rutland, devicetree, Masami Hiramatsu, Kunihiko Hayashi,
Jassi Brar, Rob Herring
Add nodes of USB2 physical layer for UniPhier SoC. This supports Pro4.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
arch/arm/boot/dts/uniphier-pro4.dtsi | 35 ++++++++++++++++++++++++++++++++++-
1 file changed, 34 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/uniphier-pro4.dtsi b/arch/arm/boot/dts/uniphier-pro4.dtsi
index b994494..4b2e291 100644
--- a/arch/arm/boot/dts/uniphier-pro4.dtsi
+++ b/arch/arm/boot/dts/uniphier-pro4.dtsi
@@ -269,6 +269,8 @@
<&mio_clk 12>;
resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 8>,
<&mio_rst 12>;
+ phy-names = "usb";
+ phys = <&usb_phy0>;
has-transaction-translator;
};
@@ -283,6 +285,8 @@
<&mio_clk 13>;
resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 9>,
<&mio_rst 13>;
+ phy-names = "usb";
+ phys = <&usb_phy1>;
has-transaction-translator;
};
@@ -294,6 +298,34 @@
pinctrl: pinctrl {
compatible = "socionext,uniphier-pro4-pinctrl";
};
+
+ usb-phy {
+ compatible = "socionext,uniphier-pro4-usb2-phy";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_phy0: phy@0 {
+ reg = <0>;
+ #phy-cells = <0>;
+ };
+
+ usb_phy1: phy@1 {
+ reg = <1>;
+ #phy-cells = <0>;
+ };
+
+ usb_phy2: phy@2 {
+ reg = <2>;
+ #phy-cells = <0>;
+ vbus-supply = <&usb0_vbus>;
+ };
+
+ usb_phy3: phy@3 {
+ reg = <3>;
+ #phy-cells = <0>;
+ vbus-supply = <&usb1_vbus>;
+ };
+ };
};
soc-glue@5f900000 {
@@ -397,7 +429,7 @@
clock-names = "ref", "bus_early", "suspend";
clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
resets = <&usb0_rst 4>;
- phys = <&usb0_ssphy>;
+ phys = <&usb_phy2>, <&usb0_ssphy>;
dr_mode = "host";
};
@@ -450,6 +482,7 @@
clock-names = "ref", "bus_early", "suspend";
clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
resets = <&usb1_rst 4>;
+ phys = <&usb_phy3>;
dr_mode = "host";
};
--
2.7.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/4] ARM: dts: uniphier: Add USB2 phy nodes
@ 2018-10-02 11:12 ` Kunihiko Hayashi
0 siblings, 0 replies; 14+ messages in thread
From: Kunihiko Hayashi @ 2018-10-02 11:12 UTC (permalink / raw)
To: linux-arm-kernel
Add nodes of USB2 physical layer for UniPhier SoC. This supports Pro4.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
arch/arm/boot/dts/uniphier-pro4.dtsi | 35 ++++++++++++++++++++++++++++++++++-
1 file changed, 34 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/uniphier-pro4.dtsi b/arch/arm/boot/dts/uniphier-pro4.dtsi
index b994494..4b2e291 100644
--- a/arch/arm/boot/dts/uniphier-pro4.dtsi
+++ b/arch/arm/boot/dts/uniphier-pro4.dtsi
@@ -269,6 +269,8 @@
<&mio_clk 12>;
resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 8>,
<&mio_rst 12>;
+ phy-names = "usb";
+ phys = <&usb_phy0>;
has-transaction-translator;
};
@@ -283,6 +285,8 @@
<&mio_clk 13>;
resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 9>,
<&mio_rst 13>;
+ phy-names = "usb";
+ phys = <&usb_phy1>;
has-transaction-translator;
};
@@ -294,6 +298,34 @@
pinctrl: pinctrl {
compatible = "socionext,uniphier-pro4-pinctrl";
};
+
+ usb-phy {
+ compatible = "socionext,uniphier-pro4-usb2-phy";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_phy0: phy at 0 {
+ reg = <0>;
+ #phy-cells = <0>;
+ };
+
+ usb_phy1: phy at 1 {
+ reg = <1>;
+ #phy-cells = <0>;
+ };
+
+ usb_phy2: phy at 2 {
+ reg = <2>;
+ #phy-cells = <0>;
+ vbus-supply = <&usb0_vbus>;
+ };
+
+ usb_phy3: phy at 3 {
+ reg = <3>;
+ #phy-cells = <0>;
+ vbus-supply = <&usb1_vbus>;
+ };
+ };
};
soc-glue at 5f900000 {
@@ -397,7 +429,7 @@
clock-names = "ref", "bus_early", "suspend";
clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
resets = <&usb0_rst 4>;
- phys = <&usb0_ssphy>;
+ phys = <&usb_phy2>, <&usb0_ssphy>;
dr_mode = "host";
};
@@ -450,6 +482,7 @@
clock-names = "ref", "bus_early", "suspend";
clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
resets = <&usb1_rst 4>;
+ phys = <&usb_phy3>;
dr_mode = "host";
};
--
2.7.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 3/4] arm64: dts: uniphier: Add USB3 controller nodes
2018-10-02 11:11 ` Kunihiko Hayashi
@ 2018-10-02 11:12 ` Kunihiko Hayashi
-1 siblings, 0 replies; 14+ messages in thread
From: Kunihiko Hayashi @ 2018-10-02 11:12 UTC (permalink / raw)
To: Masahiro Yamada, linux-arm-kernel
Cc: Mark Rutland, devicetree, Masami Hiramatsu, Kunihiko Hayashi,
Jassi Brar, Rob Herring
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for LD20, PXs3 and the boards. This includes
additional efuse nodes for obtaining PHY trimming values.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
.../boot/dts/socionext/uniphier-ld20-global.dts | 4 +
.../arm64/boot/dts/socionext/uniphier-ld20-ref.dts | 4 +
arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi | 194 +++++++++++++++++
.../arm64/boot/dts/socionext/uniphier-pxs3-ref.dts | 8 +
arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi | 240 +++++++++++++++++++++
5 files changed, 450 insertions(+)
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts
index 1a5e7c2..d7ae28a 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts
@@ -148,3 +148,7 @@
&nand {
status = "okay";
};
+
+&usb {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
index 440c2e6..406244a 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
@@ -75,3 +75,7 @@
drive-strength = <9>;
};
};
+
+&usb {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
index caf1126..dcf6178 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
@@ -553,6 +553,50 @@
efuse@200 {
compatible = "socionext,uniphier-efuse";
reg = <0x200 0x68>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* USB cells */
+ usb_rterm0: trim@54,4 {
+ reg = <0x54 1>;
+ bits = <4 2>;
+ };
+ usb_rterm1: trim@55,4 {
+ reg = <0x55 1>;
+ bits = <4 2>;
+ };
+ usb_rterm2: trim@58,4 {
+ reg = <0x58 1>;
+ bits = <4 2>;
+ };
+ usb_rterm3: trim@59,4 {
+ reg = <0x59 1>;
+ bits = <4 2>;
+ };
+ usb_sel_t0: trim@54,0 {
+ reg = <0x54 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t1: trim@55,0 {
+ reg = <0x55 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t2: trim@58,0 {
+ reg = <0x58 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t3: trim@59,0 {
+ reg = <0x59 1>;
+ bits = <0 4>;
+ };
+ usb_hs_i0: trim@56,0 {
+ reg = <0x56 1>;
+ bits = <0 4>;
+ };
+ usb_hs_i2: trim@5a,0 {
+ reg = <0x5a 1>;
+ bits = <0 4>;
+ };
};
};
@@ -620,6 +664,156 @@
};
};
+ usb: usb@65a00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65a00000 0xcd00>;
+ interrupt-names = "host";
+ interrupts = <0 134 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb1>,
+ <&pinctrl_usb2>, <&pinctrl_usb3>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 14>, <&sys_clk 14>, <&sys_clk 14>;
+ resets = <&usb_rst 15>;
+ phys = <&usb_hsphy0>, <&usb_hsphy1>,
+ <&usb_hsphy2>, <&usb_hsphy3>,
+ <&usb_ssphy0>, <&usb_ssphy1>;
+ dr_mode = "host";
+ };
+
+ usb-glue@65b00000 {
+ compatible = "socionext,uniphier-ld20-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65b00000 0x400>;
+
+ usb_rst: reset@0 {
+ compatible = "socionext,uniphier-ld20-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb_vbus0: regulator@100 {
+ compatible = "socionext,uniphier-ld20-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb_vbus1: regulator@110 {
+ compatible = "socionext,uniphier-ld20-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb_vbus2: regulator@120 {
+ compatible = "socionext,uniphier-ld20-usb3-regulator";
+ reg = <0x120 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb_vbus3: regulator@130 {
+ compatible = "socionext,uniphier-ld20-usb3-regulator";
+ reg = <0x130 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb_hsphy0: hs-phy@200 {
+ compatible = "socionext,uniphier-ld20-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 16>;
+ vbus-supply = <&usb_vbus0>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>,
+ <&usb_hs_i0>;
+ };
+
+ usb_hsphy1: hs-phy@210 {
+ compatible = "socionext,uniphier-ld20-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 16>;
+ vbus-supply = <&usb_vbus1>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm1>, <&usb_sel_t1>,
+ <&usb_hs_i0>;
+ };
+
+ usb_hsphy2: hs-phy@220 {
+ compatible = "socionext,uniphier-ld20-usb3-hsphy";
+ reg = <0x220 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 17>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 17>;
+ vbus-supply = <&usb_vbus2>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm2>, <&usb_sel_t2>,
+ <&usb_hs_i2>;
+ };
+
+ usb_hsphy3: hs-phy@230 {
+ compatible = "socionext,uniphier-ld20-usb3-hsphy";
+ reg = <0x230 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 17>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 17>;
+ vbus-supply = <&usb_vbus3>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm3>, <&usb_sel_t3>,
+ <&usb_hs_i2>;
+ };
+
+ usb_ssphy0: ss-phy@300 {
+ compatible = "socionext,uniphier-ld20-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 18>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 18>;
+ vbus-supply = <&usb_vbus0>;
+ };
+
+ usb_ssphy1: ss-phy@310 {
+ compatible = "socionext,uniphier-ld20-usb3-ssphy";
+ reg = <0x310 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 19>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 19>;
+ vbus-supply = <&usb_vbus1>;
+ };
+ };
+
nand: nand@68000000 {
compatible = "socionext,uniphier-denali-nand-v5b";
status = "disabled";
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts
index c1bb607..b00db39 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts
@@ -100,3 +100,11 @@
&nand {
status = "okay";
};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
index 2a4cf42..f688bd7 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
@@ -366,6 +366,50 @@
efuse@200 {
compatible = "socionext,uniphier-efuse";
reg = <0x200 0x68>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* USB cells */
+ usb_rterm0: trim@54,4 {
+ reg = <0x54 1>;
+ bits = <4 2>;
+ };
+ usb_rterm1: trim@55,4 {
+ reg = <0x55 1>;
+ bits = <4 2>;
+ };
+ usb_rterm2: trim@58,4 {
+ reg = <0x58 1>;
+ bits = <4 2>;
+ };
+ usb_rterm3: trim@59,4 {
+ reg = <0x59 1>;
+ bits = <4 2>;
+ };
+ usb_sel_t0: trim@54,0 {
+ reg = <0x54 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t1: trim@55,0 {
+ reg = <0x55 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t2: trim@58,0 {
+ reg = <0x58 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t3: trim@59,0 {
+ reg = <0x59 1>;
+ bits = <0 4>;
+ };
+ usb_hs_i0: trim@56,0 {
+ reg = <0x56 1>;
+ bits = <0 4>;
+ };
+ usb_hs_i2: trim@5a,0 {
+ reg = <0x5a 1>;
+ bits = <0 4>;
+ };
};
};
@@ -447,6 +491,202 @@
};
};
+ usb0: usb@65a00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65a00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 134 4>, <0 135 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
+ resets = <&usb0_rst 15>;
+ phys = <&usb0_hsphy0>, <&usb0_hsphy1>,
+ <&usb0_ssphy0>, <&usb0_ssphy1>;
+ dr_mode = "host";
+ };
+
+ usb-glue@65b00000 {
+ compatible = "socionext,uniphier-pxs3-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65b00000 0x400>;
+
+ usb0_rst: reset@0 {
+ compatible = "socionext,uniphier-pxs3-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 12>;
+ reset-names = "link";
+ resets = <&sys_rst 12>;
+ };
+
+ usb0_vbus0: regulator@100 {
+ compatible = "socionext,uniphier-pxs3-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 12>;
+ reset-names = "link";
+ resets = <&sys_rst 12>;
+ };
+
+ usb0_vbus1: regulator@110 {
+ compatible = "socionext,uniphier-pxs3-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 12>;
+ reset-names = "link";
+ resets = <&sys_rst 12>;
+ };
+
+ usb0_hsphy0: hs-phy@200 {
+ compatible = "socionext,uniphier-pxs3-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 12>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 16>;
+ vbus-supply = <&usb0_vbus0>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>,
+ <&usb_hs_i0>;
+ };
+
+ usb0_hsphy1: hs-phy@210 {
+ compatible = "socionext,uniphier-pxs3-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 12>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 16>;
+ vbus-supply = <&usb0_vbus1>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm1>, <&usb_sel_t1>,
+ <&usb_hs_i0>;
+ };
+
+ usb0_ssphy0: ss-phy@300 {
+ compatible = "socionext,uniphier-pxs3-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 12>, <&sys_clk 17>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 17>;
+ vbus-supply = <&usb0_vbus0>;
+ };
+
+ usb0_ssphy1: ss-phy@310 {
+ compatible = "socionext,uniphier-pxs3-usb3-ssphy";
+ reg = <0x310 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 12>, <&sys_clk 18>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 18>;
+ vbus-supply = <&usb0_vbus1>;
+ };
+ };
+
+ usb1: usb@65c00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65c00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 137 4>, <0 138 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 13>, <&sys_clk 13>, <&sys_clk 13>;
+ resets = <&usb1_rst 15>;
+ phys = <&usb1_hsphy0>, <&usb1_hsphy1>,
+ <&usb1_ssphy0>;
+ dr_mode = "host";
+ };
+
+ usb-glue@65d00000 {
+ compatible = "socionext,uniphier-pxs3-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65d00000 0x400>;
+
+ usb1_rst: reset@0 {
+ compatible = "socionext,uniphier-pxs3-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 13>;
+ reset-names = "link";
+ resets = <&sys_rst 13>;
+ };
+
+ usb1_vbus0: regulator@100 {
+ compatible = "socionext,uniphier-pxs3-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 13>;
+ reset-names = "link";
+ resets = <&sys_rst 13>;
+ };
+
+ usb1_vbus1: regulator@110 {
+ compatible = "socionext,uniphier-pxs3-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 13>;
+ reset-names = "link";
+ resets = <&sys_rst 13>;
+ };
+
+ usb1_hsphy0: hs-phy@200 {
+ compatible = "socionext,uniphier-pxs3-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy", "phy-ext";
+ clocks = <&sys_clk 13>, <&sys_clk 20>,
+ <&sys_clk 14>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 13>, <&sys_rst 20>;
+ vbus-supply = <&usb1_vbus0>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm2>, <&usb_sel_t2>,
+ <&usb_hs_i2>;
+ };
+
+ usb1_hsphy1: hs-phy@210 {
+ compatible = "socionext,uniphier-pxs3-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy", "phy-ext";
+ clocks = <&sys_clk 13>, <&sys_clk 20>,
+ <&sys_clk 14>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 13>, <&sys_rst 20>;
+ vbus-supply = <&usb1_vbus1>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm3>, <&usb_sel_t3>,
+ <&usb_hs_i2>;
+ };
+
+ usb1_ssphy0: ss-phy@300 {
+ compatible = "socionext,uniphier-pxs3-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy", "phy-ext";
+ clocks = <&sys_clk 13>, <&sys_clk 21>,
+ <&sys_clk 14>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 13>, <&sys_rst 21>;
+ vbus-supply = <&usb1_vbus0>;
+ };
+ };
+
nand: nand@68000000 {
compatible = "socionext,uniphier-denali-nand-v5b";
status = "disabled";
--
2.7.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 3/4] arm64: dts: uniphier: Add USB3 controller nodes
@ 2018-10-02 11:12 ` Kunihiko Hayashi
0 siblings, 0 replies; 14+ messages in thread
From: Kunihiko Hayashi @ 2018-10-02 11:12 UTC (permalink / raw)
To: linux-arm-kernel
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for LD20, PXs3 and the boards. This includes
additional efuse nodes for obtaining PHY trimming values.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
.../boot/dts/socionext/uniphier-ld20-global.dts | 4 +
.../arm64/boot/dts/socionext/uniphier-ld20-ref.dts | 4 +
arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi | 194 +++++++++++++++++
.../arm64/boot/dts/socionext/uniphier-pxs3-ref.dts | 8 +
arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi | 240 +++++++++++++++++++++
5 files changed, 450 insertions(+)
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts
index 1a5e7c2..d7ae28a 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts
@@ -148,3 +148,7 @@
&nand {
status = "okay";
};
+
+&usb {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
index 440c2e6..406244a 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
@@ -75,3 +75,7 @@
drive-strength = <9>;
};
};
+
+&usb {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
index caf1126..dcf6178 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
@@ -553,6 +553,50 @@
efuse at 200 {
compatible = "socionext,uniphier-efuse";
reg = <0x200 0x68>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* USB cells */
+ usb_rterm0: trim at 54,4 {
+ reg = <0x54 1>;
+ bits = <4 2>;
+ };
+ usb_rterm1: trim at 55,4 {
+ reg = <0x55 1>;
+ bits = <4 2>;
+ };
+ usb_rterm2: trim at 58,4 {
+ reg = <0x58 1>;
+ bits = <4 2>;
+ };
+ usb_rterm3: trim at 59,4 {
+ reg = <0x59 1>;
+ bits = <4 2>;
+ };
+ usb_sel_t0: trim at 54,0 {
+ reg = <0x54 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t1: trim at 55,0 {
+ reg = <0x55 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t2: trim at 58,0 {
+ reg = <0x58 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t3: trim at 59,0 {
+ reg = <0x59 1>;
+ bits = <0 4>;
+ };
+ usb_hs_i0: trim at 56,0 {
+ reg = <0x56 1>;
+ bits = <0 4>;
+ };
+ usb_hs_i2: trim at 5a,0 {
+ reg = <0x5a 1>;
+ bits = <0 4>;
+ };
};
};
@@ -620,6 +664,156 @@
};
};
+ usb: usb at 65a00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65a00000 0xcd00>;
+ interrupt-names = "host";
+ interrupts = <0 134 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb1>,
+ <&pinctrl_usb2>, <&pinctrl_usb3>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 14>, <&sys_clk 14>, <&sys_clk 14>;
+ resets = <&usb_rst 15>;
+ phys = <&usb_hsphy0>, <&usb_hsphy1>,
+ <&usb_hsphy2>, <&usb_hsphy3>,
+ <&usb_ssphy0>, <&usb_ssphy1>;
+ dr_mode = "host";
+ };
+
+ usb-glue at 65b00000 {
+ compatible = "socionext,uniphier-ld20-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65b00000 0x400>;
+
+ usb_rst: reset at 0 {
+ compatible = "socionext,uniphier-ld20-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb_vbus0: regulator at 100 {
+ compatible = "socionext,uniphier-ld20-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb_vbus1: regulator at 110 {
+ compatible = "socionext,uniphier-ld20-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb_vbus2: regulator at 120 {
+ compatible = "socionext,uniphier-ld20-usb3-regulator";
+ reg = <0x120 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb_vbus3: regulator at 130 {
+ compatible = "socionext,uniphier-ld20-usb3-regulator";
+ reg = <0x130 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 14>;
+ reset-names = "link";
+ resets = <&sys_rst 14>;
+ };
+
+ usb_hsphy0: hs-phy at 200 {
+ compatible = "socionext,uniphier-ld20-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 16>;
+ vbus-supply = <&usb_vbus0>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>,
+ <&usb_hs_i0>;
+ };
+
+ usb_hsphy1: hs-phy at 210 {
+ compatible = "socionext,uniphier-ld20-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 16>;
+ vbus-supply = <&usb_vbus1>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm1>, <&usb_sel_t1>,
+ <&usb_hs_i0>;
+ };
+
+ usb_hsphy2: hs-phy at 220 {
+ compatible = "socionext,uniphier-ld20-usb3-hsphy";
+ reg = <0x220 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 17>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 17>;
+ vbus-supply = <&usb_vbus2>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm2>, <&usb_sel_t2>,
+ <&usb_hs_i2>;
+ };
+
+ usb_hsphy3: hs-phy at 230 {
+ compatible = "socionext,uniphier-ld20-usb3-hsphy";
+ reg = <0x230 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 17>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 17>;
+ vbus-supply = <&usb_vbus3>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm3>, <&usb_sel_t3>,
+ <&usb_hs_i2>;
+ };
+
+ usb_ssphy0: ss-phy at 300 {
+ compatible = "socionext,uniphier-ld20-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 18>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 18>;
+ vbus-supply = <&usb_vbus0>;
+ };
+
+ usb_ssphy1: ss-phy at 310 {
+ compatible = "socionext,uniphier-ld20-usb3-ssphy";
+ reg = <0x310 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 14>, <&sys_clk 19>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 14>, <&sys_rst 19>;
+ vbus-supply = <&usb_vbus1>;
+ };
+ };
+
nand: nand at 68000000 {
compatible = "socionext,uniphier-denali-nand-v5b";
status = "disabled";
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts
index c1bb607..b00db39 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts
@@ -100,3 +100,11 @@
&nand {
status = "okay";
};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
index 2a4cf42..f688bd7 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
@@ -366,6 +366,50 @@
efuse at 200 {
compatible = "socionext,uniphier-efuse";
reg = <0x200 0x68>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* USB cells */
+ usb_rterm0: trim at 54,4 {
+ reg = <0x54 1>;
+ bits = <4 2>;
+ };
+ usb_rterm1: trim at 55,4 {
+ reg = <0x55 1>;
+ bits = <4 2>;
+ };
+ usb_rterm2: trim at 58,4 {
+ reg = <0x58 1>;
+ bits = <4 2>;
+ };
+ usb_rterm3: trim at 59,4 {
+ reg = <0x59 1>;
+ bits = <4 2>;
+ };
+ usb_sel_t0: trim at 54,0 {
+ reg = <0x54 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t1: trim at 55,0 {
+ reg = <0x55 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t2: trim at 58,0 {
+ reg = <0x58 1>;
+ bits = <0 4>;
+ };
+ usb_sel_t3: trim at 59,0 {
+ reg = <0x59 1>;
+ bits = <0 4>;
+ };
+ usb_hs_i0: trim at 56,0 {
+ reg = <0x56 1>;
+ bits = <0 4>;
+ };
+ usb_hs_i2: trim at 5a,0 {
+ reg = <0x5a 1>;
+ bits = <0 4>;
+ };
};
};
@@ -447,6 +491,202 @@
};
};
+ usb0: usb at 65a00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65a00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 134 4>, <0 135 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 12>, <&sys_clk 12>, <&sys_clk 12>;
+ resets = <&usb0_rst 15>;
+ phys = <&usb0_hsphy0>, <&usb0_hsphy1>,
+ <&usb0_ssphy0>, <&usb0_ssphy1>;
+ dr_mode = "host";
+ };
+
+ usb-glue at 65b00000 {
+ compatible = "socionext,uniphier-pxs3-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65b00000 0x400>;
+
+ usb0_rst: reset at 0 {
+ compatible = "socionext,uniphier-pxs3-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 12>;
+ reset-names = "link";
+ resets = <&sys_rst 12>;
+ };
+
+ usb0_vbus0: regulator at 100 {
+ compatible = "socionext,uniphier-pxs3-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 12>;
+ reset-names = "link";
+ resets = <&sys_rst 12>;
+ };
+
+ usb0_vbus1: regulator at 110 {
+ compatible = "socionext,uniphier-pxs3-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 12>;
+ reset-names = "link";
+ resets = <&sys_rst 12>;
+ };
+
+ usb0_hsphy0: hs-phy at 200 {
+ compatible = "socionext,uniphier-pxs3-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 12>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 16>;
+ vbus-supply = <&usb0_vbus0>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>,
+ <&usb_hs_i0>;
+ };
+
+ usb0_hsphy1: hs-phy at 210 {
+ compatible = "socionext,uniphier-pxs3-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 12>, <&sys_clk 16>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 16>;
+ vbus-supply = <&usb0_vbus1>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm1>, <&usb_sel_t1>,
+ <&usb_hs_i0>;
+ };
+
+ usb0_ssphy0: ss-phy at 300 {
+ compatible = "socionext,uniphier-pxs3-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 12>, <&sys_clk 17>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 17>;
+ vbus-supply = <&usb0_vbus0>;
+ };
+
+ usb0_ssphy1: ss-phy at 310 {
+ compatible = "socionext,uniphier-pxs3-usb3-ssphy";
+ reg = <0x310 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy";
+ clocks = <&sys_clk 12>, <&sys_clk 18>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 12>, <&sys_rst 18>;
+ vbus-supply = <&usb0_vbus1>;
+ };
+ };
+
+ usb1: usb at 65c00000 {
+ compatible = "socionext,uniphier-dwc3", "snps,dwc3";
+ status = "disabled";
+ reg = <0x65c00000 0xcd00>;
+ interrupt-names = "host", "peripheral";
+ interrupts = <0 137 4>, <0 138 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
+ clock-names = "ref", "bus_early", "suspend";
+ clocks = <&sys_clk 13>, <&sys_clk 13>, <&sys_clk 13>;
+ resets = <&usb1_rst 15>;
+ phys = <&usb1_hsphy0>, <&usb1_hsphy1>,
+ <&usb1_ssphy0>;
+ dr_mode = "host";
+ };
+
+ usb-glue at 65d00000 {
+ compatible = "socionext,uniphier-pxs3-dwc3-glue",
+ "simple-mfd";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x65d00000 0x400>;
+
+ usb1_rst: reset at 0 {
+ compatible = "socionext,uniphier-pxs3-usb3-reset";
+ reg = <0x0 0x4>;
+ #reset-cells = <1>;
+ clock-names = "link";
+ clocks = <&sys_clk 13>;
+ reset-names = "link";
+ resets = <&sys_rst 13>;
+ };
+
+ usb1_vbus0: regulator at 100 {
+ compatible = "socionext,uniphier-pxs3-usb3-regulator";
+ reg = <0x100 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 13>;
+ reset-names = "link";
+ resets = <&sys_rst 13>;
+ };
+
+ usb1_vbus1: regulator at 110 {
+ compatible = "socionext,uniphier-pxs3-usb3-regulator";
+ reg = <0x110 0x10>;
+ clock-names = "link";
+ clocks = <&sys_clk 13>;
+ reset-names = "link";
+ resets = <&sys_rst 13>;
+ };
+
+ usb1_hsphy0: hs-phy at 200 {
+ compatible = "socionext,uniphier-pxs3-usb3-hsphy";
+ reg = <0x200 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy", "phy-ext";
+ clocks = <&sys_clk 13>, <&sys_clk 20>,
+ <&sys_clk 14>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 13>, <&sys_rst 20>;
+ vbus-supply = <&usb1_vbus0>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm2>, <&usb_sel_t2>,
+ <&usb_hs_i2>;
+ };
+
+ usb1_hsphy1: hs-phy at 210 {
+ compatible = "socionext,uniphier-pxs3-usb3-hsphy";
+ reg = <0x210 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy", "phy-ext";
+ clocks = <&sys_clk 13>, <&sys_clk 20>,
+ <&sys_clk 14>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 13>, <&sys_rst 20>;
+ vbus-supply = <&usb1_vbus1>;
+ nvmem-cell-names = "rterm", "sel_t", "hs_i";
+ nvmem-cells = <&usb_rterm3>, <&usb_sel_t3>,
+ <&usb_hs_i2>;
+ };
+
+ usb1_ssphy0: ss-phy at 300 {
+ compatible = "socionext,uniphier-pxs3-usb3-ssphy";
+ reg = <0x300 0x10>;
+ #phy-cells = <0>;
+ clock-names = "link", "phy", "phy-ext";
+ clocks = <&sys_clk 13>, <&sys_clk 21>,
+ <&sys_clk 14>;
+ reset-names = "link", "phy";
+ resets = <&sys_rst 13>, <&sys_rst 21>;
+ vbus-supply = <&usb1_vbus0>;
+ };
+ };
+
nand: nand at 68000000 {
compatible = "socionext,uniphier-denali-nand-v5b";
status = "disabled";
--
2.7.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 4/4] arm64: dts: uniphier: Add USB2 phy nodes
2018-10-02 11:11 ` Kunihiko Hayashi
@ 2018-10-02 11:12 ` Kunihiko Hayashi
-1 siblings, 0 replies; 14+ messages in thread
From: Kunihiko Hayashi @ 2018-10-02 11:12 UTC (permalink / raw)
To: Masahiro Yamada, linux-arm-kernel
Cc: Mark Rutland, devicetree, Masami Hiramatsu, Kunihiko Hayashi,
Jassi Brar, Rob Herring
Add nodes of USB2 physical layer for UniPhier SoC. This supports LD11.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi | 27 ++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
index d63b56e..be3fc1a 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
@@ -432,6 +432,8 @@
<&mio_clk 12>;
resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 8>,
<&mio_rst 12>;
+ phy-names = "usb";
+ phys = <&usb_phy0>;
has-transaction-translator;
};
@@ -446,6 +448,8 @@
<&mio_clk 13>;
resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 9>,
<&mio_rst 13>;
+ phy-names = "usb";
+ phys = <&usb_phy1>;
has-transaction-translator;
};
@@ -460,6 +464,8 @@
<&mio_clk 14>;
resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 10>,
<&mio_rst 14>;
+ phy-names = "usb";
+ phys = <&usb_phy2>;
has-transaction-translator;
};
@@ -488,6 +494,27 @@
pinctrl: pinctrl {
compatible = "socionext,uniphier-ld11-pinctrl";
};
+
+ usb-phy {
+ compatible = "socionext,uniphier-ld11-usb2-phy";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_phy0: phy@0 {
+ reg = <0>;
+ #phy-cells = <0>;
+ };
+
+ usb_phy1: phy@1 {
+ reg = <1>;
+ #phy-cells = <0>;
+ };
+
+ usb_phy2: phy@2 {
+ reg = <2>;
+ #phy-cells = <0>;
+ };
+ };
};
soc-glue@5f900000 {
--
2.7.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 4/4] arm64: dts: uniphier: Add USB2 phy nodes
@ 2018-10-02 11:12 ` Kunihiko Hayashi
0 siblings, 0 replies; 14+ messages in thread
From: Kunihiko Hayashi @ 2018-10-02 11:12 UTC (permalink / raw)
To: linux-arm-kernel
Add nodes of USB2 physical layer for UniPhier SoC. This supports LD11.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi | 27 ++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
index d63b56e..be3fc1a 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
@@ -432,6 +432,8 @@
<&mio_clk 12>;
resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 8>,
<&mio_rst 12>;
+ phy-names = "usb";
+ phys = <&usb_phy0>;
has-transaction-translator;
};
@@ -446,6 +448,8 @@
<&mio_clk 13>;
resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 9>,
<&mio_rst 13>;
+ phy-names = "usb";
+ phys = <&usb_phy1>;
has-transaction-translator;
};
@@ -460,6 +464,8 @@
<&mio_clk 14>;
resets = <&sys_rst 8>, <&mio_rst 7>, <&mio_rst 10>,
<&mio_rst 14>;
+ phy-names = "usb";
+ phys = <&usb_phy2>;
has-transaction-translator;
};
@@ -488,6 +494,27 @@
pinctrl: pinctrl {
compatible = "socionext,uniphier-ld11-pinctrl";
};
+
+ usb-phy {
+ compatible = "socionext,uniphier-ld11-usb2-phy";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_phy0: phy at 0 {
+ reg = <0>;
+ #phy-cells = <0>;
+ };
+
+ usb_phy1: phy at 1 {
+ reg = <1>;
+ #phy-cells = <0>;
+ };
+
+ usb_phy2: phy at 2 {
+ reg = <2>;
+ #phy-cells = <0>;
+ };
+ };
};
soc-glue at 5f900000 {
--
2.7.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 1/4] ARM: dts: uniphier: Add USB3 controller nodes
2018-10-02 11:11 ` Kunihiko Hayashi
@ 2018-10-03 3:39 ` Masahiro Yamada
-1 siblings, 0 replies; 14+ messages in thread
From: Masahiro Yamada @ 2018-10-03 3:39 UTC (permalink / raw)
To: Kunihiko Hayashi
Cc: Mark Rutland, DTML, Masami Hiramatsu, Jassi Brar, Rob Herring,
linux-arm-kernel
On Tue, Oct 2, 2018 at 8:12 PM Kunihiko Hayashi
<hayashi.kunihiko@socionext.com> wrote:
>
> Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
> and hs-phy. This supports for Pro4, PXs2 and the boards.
>
> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> ---
> arch/arm/boot/dts/uniphier-pro4-ace.dts | 8 ++
> arch/arm/boot/dts/uniphier-pro4-ref.dts | 8 ++
> arch/arm/boot/dts/uniphier-pro4.dtsi | 94 +++++++++++++++
> arch/arm/boot/dts/uniphier-pxs2-gentil.dts | 8 ++
> arch/arm/boot/dts/uniphier-pxs2-vodka.dts | 4 +
> arch/arm/boot/dts/uniphier-pxs2.dtsi | 180 +++++++++++++++++++++++++++++
> 6 files changed, 302 insertions(+)
I will enable this on uniphier-ld6b-ref.dts
and uniphier-pro4-sanji.dts as well
when I pick up this series.
--
Best Regards
Masahiro Yamada
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/4] ARM: dts: uniphier: Add USB3 controller nodes
@ 2018-10-03 3:39 ` Masahiro Yamada
0 siblings, 0 replies; 14+ messages in thread
From: Masahiro Yamada @ 2018-10-03 3:39 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Oct 2, 2018 at 8:12 PM Kunihiko Hayashi
<hayashi.kunihiko@socionext.com> wrote:
>
> Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
> and hs-phy. This supports for Pro4, PXs2 and the boards.
>
> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> ---
> arch/arm/boot/dts/uniphier-pro4-ace.dts | 8 ++
> arch/arm/boot/dts/uniphier-pro4-ref.dts | 8 ++
> arch/arm/boot/dts/uniphier-pro4.dtsi | 94 +++++++++++++++
> arch/arm/boot/dts/uniphier-pxs2-gentil.dts | 8 ++
> arch/arm/boot/dts/uniphier-pxs2-vodka.dts | 4 +
> arch/arm/boot/dts/uniphier-pxs2.dtsi | 180 +++++++++++++++++++++++++++++
> 6 files changed, 302 insertions(+)
I will enable this on uniphier-ld6b-ref.dts
and uniphier-pro4-sanji.dts as well
when I pick up this series.
--
Best Regards
Masahiro Yamada
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/4] ARM: dts: uniphier: Add USB3 controller nodes
2018-10-02 11:11 ` Kunihiko Hayashi
@ 2018-10-04 0:49 ` Masahiro Yamada
-1 siblings, 0 replies; 14+ messages in thread
From: Masahiro Yamada @ 2018-10-04 0:49 UTC (permalink / raw)
To: Kunihiko Hayashi
Cc: Mark Rutland, DTML, Masami Hiramatsu, Jassi Brar, Rob Herring,
linux-arm-kernel
On Tue, Oct 2, 2018 at 8:12 PM Kunihiko Hayashi
<hayashi.kunihiko@socionext.com> wrote:
>
> Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
> and hs-phy. This supports for Pro4, PXs2 and the boards.
>
> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> ---
> arch/arm/boot/dts/uniphier-pro4-ace.dts | 8 ++
> arch/arm/boot/dts/uniphier-pro4-ref.dts | 8 ++
> arch/arm/boot/dts/uniphier-pro4.dtsi | 94 +++++++++++++++
> arch/arm/boot/dts/uniphier-pxs2-gentil.dts | 8 ++
> arch/arm/boot/dts/uniphier-pxs2-vodka.dts | 4 +
> arch/arm/boot/dts/uniphier-pxs2.dtsi | 180 +++++++++++++++++++++++++++++
> 6 files changed, 302 insertions(+)
Series, applied.
Thanks.
--
Best Regards
Masahiro Yamada
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/4] ARM: dts: uniphier: Add USB3 controller nodes
@ 2018-10-04 0:49 ` Masahiro Yamada
0 siblings, 0 replies; 14+ messages in thread
From: Masahiro Yamada @ 2018-10-04 0:49 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Oct 2, 2018 at 8:12 PM Kunihiko Hayashi
<hayashi.kunihiko@socionext.com> wrote:
>
> Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
> and hs-phy. This supports for Pro4, PXs2 and the boards.
>
> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> ---
> arch/arm/boot/dts/uniphier-pro4-ace.dts | 8 ++
> arch/arm/boot/dts/uniphier-pro4-ref.dts | 8 ++
> arch/arm/boot/dts/uniphier-pro4.dtsi | 94 +++++++++++++++
> arch/arm/boot/dts/uniphier-pxs2-gentil.dts | 8 ++
> arch/arm/boot/dts/uniphier-pxs2-vodka.dts | 4 +
> arch/arm/boot/dts/uniphier-pxs2.dtsi | 180 +++++++++++++++++++++++++++++
> 6 files changed, 302 insertions(+)
Series, applied.
Thanks.
--
Best Regards
Masahiro Yamada
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2018-10-04 0:49 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-10-02 11:11 [PATCH 0/4] Add UniPhier USB3 controller and USB2 phy nodes Kunihiko Hayashi
2018-10-02 11:11 ` Kunihiko Hayashi
2018-10-02 11:11 ` [PATCH 1/4] ARM: dts: uniphier: Add USB3 controller nodes Kunihiko Hayashi
2018-10-02 11:11 ` Kunihiko Hayashi
2018-10-03 3:39 ` Masahiro Yamada
2018-10-03 3:39 ` Masahiro Yamada
2018-10-04 0:49 ` Masahiro Yamada
2018-10-04 0:49 ` Masahiro Yamada
2018-10-02 11:12 ` [PATCH 2/4] ARM: dts: uniphier: Add USB2 phy nodes Kunihiko Hayashi
2018-10-02 11:12 ` Kunihiko Hayashi
2018-10-02 11:12 ` [PATCH 3/4] arm64: dts: uniphier: Add USB3 controller nodes Kunihiko Hayashi
2018-10-02 11:12 ` Kunihiko Hayashi
2018-10-02 11:12 ` [PATCH 4/4] arm64: dts: uniphier: Add USB2 phy nodes Kunihiko Hayashi
2018-10-02 11:12 ` Kunihiko Hayashi
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.