From: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com> To: "linux-mtd@lists.infradead.org" <linux-mtd@lists.infradead.org>, "boris.brezillon@bootlin.com" <boris.brezillon@bootlin.com>, "marek.vasut@gmail.com" <marek.vasut@gmail.com>, "vigneshr@ti.com" <vigneshr@ti.com>, "linux-spi@vger.kernel.org" <linux-spi@vger.kernel.org>, "devicetree@vger.kernel.org" <devicetree@vger.kernel.org> Cc: "robh@kernel.org" <robh@kernel.org>, "mark.rutland@arm.com" <mark.rutland@arm.com>, "shawnguo@kernel.org" <shawnguo@kernel.org>, "linux-arm-kernel@lists.infradead.org" <linux-arm-kernel@lists.infradead.org>, "computersforpeace@gmail.com" <computersforpeace@gmail.com>, "frieder.schrempf@exceet.de" <frieder.schrempf@exceet.de>, "linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>, Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com> Subject: [PATCH v2 0/7] spi: add support for octal mode Date: Mon, 15 Oct 2018 12:13:57 +0000 [thread overview] Message-ID: <1539605534-22302-1-git-send-email-yogeshnarayan.gaur@nxp.com> (raw) Add support for octal mode IO data transfer. Micron flash, mt35xu512aba, supports octal mode data transfer and NXP FlexSPI controller supports 8 data lines for data transfer (Rx/Tx). Patch series * Add support for octal mode flags and parsing of same in spi driver. * Add parsing logic for spi-mem framework and m25p80.c device file. * Add opcodes for octal I/O commands in spi-nor framework, Read and Write proto for (1-1-8/1-8-8) mode. Opcodes are added as per octal data IO commands required for mt35xu512aba [1] flash. * Add mode bit required for octal mode in nxp-fspi driver [2]. * Define binding property 'spi-rx/tx-bus-width' for LX2160ARDB target [2]. Cherry pick below 2 patches (from: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git): c639f871febe6667d9afce28108c634e5636c735 spi: spi-mem: Fix inverted logic in op sanity check db122eb8a749a1eff038f9a282c620ab16c4be1d spi: spi-mem: Add extra sanity checks on the op param Tested on LX2160ARDB target with nxp-fspi driver, below are Read performance number of 1-1-1 and 1-1-8 read protocol. root@lxxx:~# cat /proc/mtd dev: size erasesize name mtd0: 04000000 00001000 "spi0.0" mtd1: 04000000 00001000 "spi0.1" root@lxxx:~# time mtd_debug read /dev/mtd0 0x0 0x1000000 0read Copied 16777216 bytes from address 0x00000000 in flash to 0read real 0m2.792s user 0m0.000s sys 0m2.790s root@lxxx:~# time mtd_debug read /dev/mtd1 0x0 0x1000000 0read Copied 16777216 bytes from address 0x00000000 in flash to 0read real 0m0.441s user 0m0.000s sys 0m0.440s root@ls1012ardb:~# Flash device MTD0 configured in 1-1-1 protocol. Flash device MTD1 configured in 1-1-8 protocol. [1] https://patchwork.ozlabs.org/project/linux-mtd/list/?series=70384 [2] https://patchwork.ozlabs.org/project/linux-mtd/list/?series=70210 Yogesh Gaur (7): spi: add support for octal I/O data transfer spi: spi-mem: add support for octal I/O data transfer mtd: spi-nor: add opcodes for octal Read/Write commands mtd: spi-nor: add octal read flag for flash mt35xu512aba mtd: m25p80: add support of octal I/O transfer spi: nxp-fspi: add mode flag bit for octal support arm64: dts: lx2160a: update fspi node Changes for v2: Incorporated review comments of Boris and Vignesh. arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts | 4 ++++ drivers/mtd/devices/m25p80.c | 9 ++++++++- drivers/mtd/spi-nor/spi-nor.c | 15 ++++++++++++++- drivers/spi/spi-mem.c | 9 ++++++++- drivers/spi/spi-nxp-fspi.c | 4 ++-- drivers/spi/spi.c | 6 ++++++ include/linux/mtd/spi-nor.h | 8 ++++++++ include/linux/spi/spi.h | 2 ++ 8 files changed, 52 insertions(+), 5 deletions(-) -- 2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: yogeshnarayan.gaur@nxp.com (Yogesh Narayan Gaur) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v2 0/7] spi: add support for octal mode Date: Mon, 15 Oct 2018 12:13:57 +0000 [thread overview] Message-ID: <1539605534-22302-1-git-send-email-yogeshnarayan.gaur@nxp.com> (raw) Add support for octal mode IO data transfer. Micron flash, mt35xu512aba, supports octal mode data transfer and NXP FlexSPI controller supports 8 data lines for data transfer (Rx/Tx). Patch series * Add support for octal mode flags and parsing of same in spi driver. * Add parsing logic for spi-mem framework and m25p80.c device file. * Add opcodes for octal I/O commands in spi-nor framework, Read and Write proto for (1-1-8/1-8-8) mode. Opcodes are added as per octal data IO commands required for mt35xu512aba [1] flash. * Add mode bit required for octal mode in nxp-fspi driver [2]. * Define binding property 'spi-rx/tx-bus-width' for LX2160ARDB target [2]. Cherry pick below 2 patches (from: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git): c639f871febe6667d9afce28108c634e5636c735 spi: spi-mem: Fix inverted logic in op sanity check db122eb8a749a1eff038f9a282c620ab16c4be1d spi: spi-mem: Add extra sanity checks on the op param Tested on LX2160ARDB target with nxp-fspi driver, below are Read performance number of 1-1-1 and 1-1-8 read protocol. root at lxxx:~# cat /proc/mtd dev: size erasesize name mtd0: 04000000 00001000 "spi0.0" mtd1: 04000000 00001000 "spi0.1" root at lxxx:~# time mtd_debug read /dev/mtd0 0x0 0x1000000 0read Copied 16777216 bytes from address 0x00000000 in flash to 0read real 0m2.792s user 0m0.000s sys 0m2.790s root at lxxx:~# time mtd_debug read /dev/mtd1 0x0 0x1000000 0read Copied 16777216 bytes from address 0x00000000 in flash to 0read real 0m0.441s user 0m0.000s sys 0m0.440s root at ls1012ardb:~# Flash device MTD0 configured in 1-1-1 protocol. Flash device MTD1 configured in 1-1-8 protocol. [1] https://patchwork.ozlabs.org/project/linux-mtd/list/?series=70384 [2] https://patchwork.ozlabs.org/project/linux-mtd/list/?series=70210 Yogesh Gaur (7): spi: add support for octal I/O data transfer spi: spi-mem: add support for octal I/O data transfer mtd: spi-nor: add opcodes for octal Read/Write commands mtd: spi-nor: add octal read flag for flash mt35xu512aba mtd: m25p80: add support of octal I/O transfer spi: nxp-fspi: add mode flag bit for octal support arm64: dts: lx2160a: update fspi node Changes for v2: Incorporated review comments of Boris and Vignesh. arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts | 4 ++++ drivers/mtd/devices/m25p80.c | 9 ++++++++- drivers/mtd/spi-nor/spi-nor.c | 15 ++++++++++++++- drivers/spi/spi-mem.c | 9 ++++++++- drivers/spi/spi-nxp-fspi.c | 4 ++-- drivers/spi/spi.c | 6 ++++++ include/linux/mtd/spi-nor.h | 8 ++++++++ include/linux/spi/spi.h | 2 ++ 8 files changed, 52 insertions(+), 5 deletions(-) -- 2.7.4
next reply other threads:[~2018-10-15 12:14 UTC|newest] Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top 2018-10-15 12:13 Yogesh Narayan Gaur [this message] 2018-10-15 12:13 ` [PATCH v2 0/7] spi: add support for octal mode Yogesh Narayan Gaur 2018-10-15 12:13 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` [PATCH v2 1/7] spi: add support for octal I/O data transfer Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` [PATCH v2 2/7] spi: spi-mem: " Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` [PATCH v2 3/7] mtd: spi-nor: add opcodes for octal Read/Write commands Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` [PATCH v2 4/7] mtd: spi-nor: add octal read flag for flash mt35xu512aba Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` [PATCH v2 5/7] mtd: m25p80: add support of octal I/O transfer Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` [PATCH v2 6/7] spi: nxp-fspi: add mode flag bit for octal support Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` [PATCH v2 7/7] arm64: dts: lx2160a: update fspi node Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-15 12:14 ` Yogesh Narayan Gaur 2018-10-22 12:40 ` [PATCH v2 0/7] spi: add support for octal mode Boris Brezillon 2018-10-22 12:40 ` Boris Brezillon 2018-10-22 12:40 ` Boris Brezillon -- strict thread matches above, loose matches on Subject: below -- 2018-10-15 11:47 Yogesh Narayan Gaur 2018-10-15 11:47 ` Yogesh Narayan Gaur 2018-10-15 11:47 ` Yogesh Narayan Gaur 2018-10-15 11:54 ` Boris Brezillon 2018-10-15 11:54 ` Boris Brezillon 2018-10-15 11:54 ` Boris Brezillon 2018-10-15 11:58 ` Yogesh Narayan Gaur 2018-10-15 11:58 ` Yogesh Narayan Gaur 2018-10-15 11:58 ` Yogesh Narayan Gaur
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1539605534-22302-1-git-send-email-yogeshnarayan.gaur@nxp.com \ --to=yogeshnarayan.gaur@nxp.com \ --cc=boris.brezillon@bootlin.com \ --cc=computersforpeace@gmail.com \ --cc=devicetree@vger.kernel.org \ --cc=frieder.schrempf@exceet.de \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-mtd@lists.infradead.org \ --cc=linux-spi@vger.kernel.org \ --cc=marek.vasut@gmail.com \ --cc=mark.rutland@arm.com \ --cc=robh@kernel.org \ --cc=shawnguo@kernel.org \ --cc=vigneshr@ti.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.