* [PATCH 0/3] ARM: dts: add Raspberry Pi 3 A+
@ 2018-11-15 22:29 Stefan Wahren
2018-11-15 22:29 ` [PATCH 1/3] dt-bindings: bcm: Add " Stefan Wahren
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Stefan Wahren @ 2018-11-15 22:29 UTC (permalink / raw)
To: linux-arm-kernel
This patch series adds support for the brand new Raspberry Pi 3 A+ .
Stefan Wahren (3):
dt-bindings: bcm: Add Raspberry Pi 3 A+
ARM: dts: add Raspberry Pi 3 A+
arm64: dts: broadcom: Add reference to RPi 3 A+
.../devicetree/bindings/arm/bcm/brcm,bcm2835.txt | 4 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts | 107 +++++++++++++++++++++
.../boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts | 2 +
4 files changed, 114 insertions(+)
create mode 100644 arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
create mode 100644 arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
--
2.7.4
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH 1/3] dt-bindings: bcm: Add Raspberry Pi 3 A+
2018-11-15 22:29 [PATCH 0/3] ARM: dts: add Raspberry Pi 3 A+ Stefan Wahren
@ 2018-11-15 22:29 ` Stefan Wahren
2018-11-15 22:29 ` [PATCH 2/3] ARM: dts: add " Stefan Wahren
2018-11-15 22:29 ` [PATCH 3/3] arm64: dts: broadcom: Add reference to RPi " Stefan Wahren
2 siblings, 0 replies; 4+ messages in thread
From: Stefan Wahren @ 2018-11-15 22:29 UTC (permalink / raw)
To: linux-arm-kernel
This adds the root properties for the Raspberry Pi 3 A+ .
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
index 0dcc3ea..245328f 100644
--- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
@@ -30,6 +30,10 @@ Raspberry Pi 2 Model B
Required root node properties:
compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
+Raspberry Pi 3 Model A+
+Required root node properties:
+compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837";
+
Raspberry Pi 3 Model B
Required root node properties:
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 2/3] ARM: dts: add Raspberry Pi 3 A+
2018-11-15 22:29 [PATCH 0/3] ARM: dts: add Raspberry Pi 3 A+ Stefan Wahren
2018-11-15 22:29 ` [PATCH 1/3] dt-bindings: bcm: Add " Stefan Wahren
@ 2018-11-15 22:29 ` Stefan Wahren
2018-11-15 22:29 ` [PATCH 3/3] arm64: dts: broadcom: Add reference to RPi " Stefan Wahren
2 siblings, 0 replies; 4+ messages in thread
From: Stefan Wahren @ 2018-11-15 22:29 UTC (permalink / raw)
To: linux-arm-kernel
The Raspberry Pi 3 A+ is similar to the Pi 3 B+ but has only 512 MB RAM,
1 USB 2.0 port and no Ethernet.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts | 107 +++++++++++++++++++++++++++++
2 files changed, 108 insertions(+)
create mode 100644 arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b0e966d..15bbd0d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -79,6 +79,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
bcm2835-rpi-a-plus.dtb \
bcm2835-rpi-cm1-io1.dtb \
bcm2836-rpi-2-b.dtb \
+ bcm2837-rpi-3-a-plus.dtb \
bcm2837-rpi-3-b.dtb \
bcm2837-rpi-3-b-plus.dtb \
bcm2837-rpi-cm3-io3.dtb \
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
new file mode 100644
index 0000000..75785dd
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837";
+ model = "Raspberry Pi 3 Model A+";
+
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory {
+ reg = <0 0x20000000>;
+ };
+
+ leds {
+ act {
+ gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr {
+ label = "PWR";
+ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&expgpio 1 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "BT_ON",
+ "WL_ON",
+ "STATUS_LED",
+ "",
+ "",
+ "CAM_GPIO0",
+ "CAM_GPIO1",
+ "";
+ status = "okay";
+ };
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+ status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_gpio34>;
+ status = "okay";
+ bus-width = <4>;
+ non-removable;
+ mmc-pwrseq = <&wifi_pwrseq>;
+
+ brcmf: wifi at 1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ status = "okay";
+ bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 3/3] arm64: dts: broadcom: Add reference to RPi 3 A+
2018-11-15 22:29 [PATCH 0/3] ARM: dts: add Raspberry Pi 3 A+ Stefan Wahren
2018-11-15 22:29 ` [PATCH 1/3] dt-bindings: bcm: Add " Stefan Wahren
2018-11-15 22:29 ` [PATCH 2/3] ARM: dts: add " Stefan Wahren
@ 2018-11-15 22:29 ` Stefan Wahren
2 siblings, 0 replies; 4+ messages in thread
From: Stefan Wahren @ 2018-11-15 22:29 UTC (permalink / raw)
To: linux-arm-kernel
This adds a reference to the dts of the Raspberry Pi 3 A+,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts | 2 ++
1 file changed, 2 insertions(+)
create mode 100644 arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
diff --git a/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts b/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
new file mode 100644
index 0000000..f0ec56a
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "arm/bcm2837-rpi-3-a-plus.dts"
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
end of thread, other threads:[~2018-11-15 22:29 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-11-15 22:29 [PATCH 0/3] ARM: dts: add Raspberry Pi 3 A+ Stefan Wahren
2018-11-15 22:29 ` [PATCH 1/3] dt-bindings: bcm: Add " Stefan Wahren
2018-11-15 22:29 ` [PATCH 2/3] ARM: dts: add " Stefan Wahren
2018-11-15 22:29 ` [PATCH 3/3] arm64: dts: broadcom: Add reference to RPi " Stefan Wahren
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.