* [PATCH INTERNAL V3 0/3] Add support for PWM Configure and stablize for PWM kona @ 2019-01-11 5:08 ` Sheetal Tigadoli 0 siblings, 0 replies; 12+ messages in thread From: Sheetal Tigadoli @ 2019-01-11 5:08 UTC (permalink / raw) To: Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: bcm-kernel-feedback-list, linux-pwm, devicetree, linux-kernel, linux-arm-kernel, Sheetal Tigadoli Hi, This patchset contain support to make PWM changes configure and stablize Following are brief changes done a. Add support for version2 compatible string b. Change PWM config and stablize delay in PWM Kona Praveen Kumar B (3): dt-bindings: pwm: kona: Add new compatible for new version pwm-kona drivers: pwm: pwm-bcm-kona: Add pwm-kona-v2 support ARM: dts: cygnus: Change pwm compatible to new version .../devicetree/bindings/pwm/brcm,kona-pwm.txt | 2 +- arch/arm/boot/dts/bcm-cygnus.dtsi | 2 +- drivers/pwm/pwm-bcm-kona.c | 128 ++++++++++++++++----- 3 files changed, 100 insertions(+), 32 deletions(-) -- 1.9.1 ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH INTERNAL V3 0/3] Add support for PWM Configure and stablize for PWM kona @ 2019-01-11 5:08 ` Sheetal Tigadoli 0 siblings, 0 replies; 12+ messages in thread From: Sheetal Tigadoli @ 2019-01-11 5:08 UTC (permalink / raw) To: Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: linux-pwm, Sheetal Tigadoli, devicetree, linux-kernel, bcm-kernel-feedback-list, linux-arm-kernel Hi, This patchset contain support to make PWM changes configure and stablize Following are brief changes done a. Add support for version2 compatible string b. Change PWM config and stablize delay in PWM Kona Praveen Kumar B (3): dt-bindings: pwm: kona: Add new compatible for new version pwm-kona drivers: pwm: pwm-bcm-kona: Add pwm-kona-v2 support ARM: dts: cygnus: Change pwm compatible to new version .../devicetree/bindings/pwm/brcm,kona-pwm.txt | 2 +- arch/arm/boot/dts/bcm-cygnus.dtsi | 2 +- drivers/pwm/pwm-bcm-kona.c | 128 ++++++++++++++++----- 3 files changed, 100 insertions(+), 32 deletions(-) -- 1.9.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH INTERNAL V3 1/3] dt-bindings: pwm: kona: Add new compatible for new version pwm-kona 2019-01-11 5:08 ` Sheetal Tigadoli @ 2019-01-11 5:08 ` Sheetal Tigadoli -1 siblings, 0 replies; 12+ messages in thread From: Sheetal Tigadoli @ 2019-01-11 5:08 UTC (permalink / raw) To: Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: bcm-kernel-feedback-list, linux-pwm, devicetree, linux-kernel, linux-arm-kernel, Praveen Kumar B, Sheetal Tigadoli From: Praveen Kumar B <praveen.b@broadcom.com> Add new compatible string for new version of pwm-kona Signed-off-by: Praveen Kumar B <praveen.b@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com> --- Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt index 8eae9fe..d37f697 100644 --- a/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt @@ -3,7 +3,7 @@ Broadcom Kona PWM controller device tree bindings This controller has 6 channels. Required Properties : -- compatible: should contain "brcm,kona-pwm" +- compatible: should contain "brcm,kona-pwm" or "brcm,kona-pwm-v2" - reg: physical base address and length of the controller's registers - clocks: phandle + clock specifier pair for the external clock - #pwm-cells: Should be 3. See pwm.txt in this directory for a -- 1.9.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH INTERNAL V3 1/3] dt-bindings: pwm: kona: Add new compatible for new version pwm-kona @ 2019-01-11 5:08 ` Sheetal Tigadoli 0 siblings, 0 replies; 12+ messages in thread From: Sheetal Tigadoli @ 2019-01-11 5:08 UTC (permalink / raw) To: Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: linux-pwm, Sheetal Tigadoli, Praveen Kumar B, devicetree, linux-kernel, bcm-kernel-feedback-list, linux-arm-kernel From: Praveen Kumar B <praveen.b@broadcom.com> Add new compatible string for new version of pwm-kona Signed-off-by: Praveen Kumar B <praveen.b@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com> --- Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt index 8eae9fe..d37f697 100644 --- a/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt @@ -3,7 +3,7 @@ Broadcom Kona PWM controller device tree bindings This controller has 6 channels. Required Properties : -- compatible: should contain "brcm,kona-pwm" +- compatible: should contain "brcm,kona-pwm" or "brcm,kona-pwm-v2" - reg: physical base address and length of the controller's registers - clocks: phandle + clock specifier pair for the external clock - #pwm-cells: Should be 3. See pwm.txt in this directory for a -- 1.9.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH INTERNAL V3 2/3] drivers: pwm: pwm-bcm-kona: Add pwm-kona-v2 support 2019-01-11 5:08 ` Sheetal Tigadoli @ 2019-01-11 5:08 ` Sheetal Tigadoli -1 siblings, 0 replies; 12+ messages in thread From: Sheetal Tigadoli @ 2019-01-11 5:08 UTC (permalink / raw) To: Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: bcm-kernel-feedback-list, linux-pwm, devicetree, linux-kernel, linux-arm-kernel, Praveen Kumar B, Sheetal Tigadoli From: Praveen Kumar B <praveen.b@broadcom.com> Add support for new version of pwm-kona. Add support to make PWM changes configured and stable. Signed-off-by: Praveen Kumar B <praveen.b@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com> --- drivers/pwm/pwm-bcm-kona.c | 128 ++++++++++++++++++++++++++++++++++----------- 1 file changed, 98 insertions(+), 30 deletions(-) diff --git a/drivers/pwm/pwm-bcm-kona.c b/drivers/pwm/pwm-bcm-kona.c index 09a95ae..2b44ad8 100644 --- a/drivers/pwm/pwm-bcm-kona.c +++ b/drivers/pwm/pwm-bcm-kona.c @@ -45,30 +45,39 @@ * high or low depending on its state at that exact instant. */ -#define PWM_CONTROL_OFFSET (0x00000000) +#define PWM_CONTROL_OFFSET 0x00000000 #define PWM_CONTROL_SMOOTH_SHIFT(chan) (24 + (chan)) #define PWM_CONTROL_TYPE_SHIFT(chan) (16 + (chan)) #define PWM_CONTROL_POLARITY_SHIFT(chan) (8 + (chan)) #define PWM_CONTROL_TRIGGER_SHIFT(chan) (chan) -#define PRESCALE_OFFSET (0x00000004) +#define PRESCALE_OFFSET 0x00000004 #define PRESCALE_SHIFT(chan) ((chan) << 2) #define PRESCALE_MASK(chan) (0x7 << PRESCALE_SHIFT(chan)) -#define PRESCALE_MIN (0x00000000) -#define PRESCALE_MAX (0x00000007) +#define PRESCALE_MIN 0x00000000 +#define PRESCALE_MAX 0x00000007 #define PERIOD_COUNT_OFFSET(chan) (0x00000008 + ((chan) << 3)) -#define PERIOD_COUNT_MIN (0x00000002) -#define PERIOD_COUNT_MAX (0x00ffffff) +#define PERIOD_COUNT_MIN 0x00000002 +#define PERIOD_COUNT_MAX 0x00ffffff #define DUTY_CYCLE_HIGH_OFFSET(chan) (0x0000000c + ((chan) << 3)) -#define DUTY_CYCLE_HIGH_MIN (0x00000000) -#define DUTY_CYCLE_HIGH_MAX (0x00ffffff) +#define DUTY_CYCLE_HIGH_MIN 0x00000000 +#define DUTY_CYCLE_HIGH_MAX 0x00ffffff + +#define PWM_MONITOR_OFFSET 0xb0 +#define PWM_MONITOR_TIMEOUT_US 5 + +enum kona_pwmc_ver { + KONA_PWM_V1 = 1, + KONA_PWM_V2 +}; struct kona_pwmc { struct pwm_chip chip; void __iomem *base; struct clk *clk; + enum kona_pwmc_ver version; }; static inline struct kona_pwmc *to_kona_pwmc(struct pwm_chip *_chip) @@ -76,11 +85,40 @@ static inline struct kona_pwmc *to_kona_pwmc(struct pwm_chip *_chip) return container_of(_chip, struct kona_pwmc, chip); } +static int kona_pwmc_wait_stable(struct pwm_chip *chip, unsigned int chan, + unsigned int kona_ver) +{ + struct kona_pwmc *kp = to_kona_pwmc(chip); + unsigned int value; + unsigned int count = PWM_MONITOR_TIMEOUT_US * 1000; + + switch (kona_ver) { + case KONA_PWM_V1: + /* + * There must be a min 400ns delay between clearing trigger and + * settingit. Failing to do this may result in no PWM signal. + */ + ndelay(400); + return 0; + case KONA_PWM_V2: + do { + value = readl(kp->base + PWM_MONITOR_OFFSET); + if (!(value & (BIT(chan)))) + return 0; + ndelay(1); + } while (count--); + + return -ETIMEDOUT; + default: + return -ENODEV; + } +} + /* * Clear trigger bit but set smooth bit to maintain old output. */ -static void kona_pwmc_prepare_for_settings(struct kona_pwmc *kp, - unsigned int chan) +static int kona_pwmc_prepare_for_settings(struct kona_pwmc *kp, + unsigned int chan) { unsigned int value = readl(kp->base + PWM_CONTROL_OFFSET); @@ -88,14 +126,10 @@ static void kona_pwmc_prepare_for_settings(struct kona_pwmc *kp, value &= ~(1 << PWM_CONTROL_TRIGGER_SHIFT(chan)); writel(value, kp->base + PWM_CONTROL_OFFSET); - /* - * There must be a min 400ns delay between clearing trigger and setting - * it. Failing to do this may result in no PWM signal. - */ - ndelay(400); + return kona_pwmc_wait_stable(&kp->chip, chan, kp->version); } -static void kona_pwmc_apply_settings(struct kona_pwmc *kp, unsigned int chan) +static int kona_pwmc_apply_settings(struct kona_pwmc *kp, unsigned int chan) { unsigned int value = readl(kp->base + PWM_CONTROL_OFFSET); @@ -104,8 +138,7 @@ static void kona_pwmc_apply_settings(struct kona_pwmc *kp, unsigned int chan) value |= 1 << PWM_CONTROL_TRIGGER_SHIFT(chan); writel(value, kp->base + PWM_CONTROL_OFFSET); - /* Trigger bit must be held high for at least 400 ns. */ - ndelay(400); + return kona_pwmc_wait_stable(&kp->chip, chan, kp->version); } static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm, @@ -115,6 +148,7 @@ static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm, u64 val, div, rate; unsigned long prescale = PRESCALE_MIN, pc, dc; unsigned int value, chan = pwm->hwpwm; + int ret; /* * Find period count, duty count and prescale to suit duty_ns and @@ -156,7 +190,12 @@ static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm, * validated immediately instead of on enable. */ if (pwm_is_enabled(pwm)) { - kona_pwmc_prepare_for_settings(kp, chan); + ret = kona_pwmc_prepare_for_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to prepare pwm settings: %d\n", + ret); + return ret; + } value = readl(kp->base + PRESCALE_OFFSET); value &= ~PRESCALE_MASK(chan); @@ -167,7 +206,12 @@ static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm, writel(dc, kp->base + DUTY_CYCLE_HIGH_OFFSET(chan)); - kona_pwmc_apply_settings(kp, chan); + ret = kona_pwmc_apply_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to apply settings: %d\n", + ret); + return ret; + } } return 0; @@ -187,7 +231,11 @@ static int kona_pwmc_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm, return ret; } - kona_pwmc_prepare_for_settings(kp, chan); + ret = kona_pwmc_prepare_for_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to prepare pwm settings: %d\n", ret); + return ret; + } value = readl(kp->base + PWM_CONTROL_OFFSET); @@ -198,7 +246,11 @@ static int kona_pwmc_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm, writel(value, kp->base + PWM_CONTROL_OFFSET); - kona_pwmc_apply_settings(kp, chan); + ret = kona_pwmc_apply_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to apply pwm settings: %d\n", ret); + return ret; + } clk_disable_unprepare(kp->clk); @@ -231,8 +283,13 @@ static void kona_pwmc_disable(struct pwm_chip *chip, struct pwm_device *pwm) struct kona_pwmc *kp = to_kona_pwmc(chip); unsigned int chan = pwm->hwpwm; unsigned int value; + int ret; - kona_pwmc_prepare_for_settings(kp, chan); + ret = kona_pwmc_prepare_for_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to prepare pwm settings: %d\n", ret); + return; + } /* Simulate a disable by configuring for zero duty */ writel(0, kp->base + DUTY_CYCLE_HIGH_OFFSET(chan)); @@ -243,7 +300,11 @@ static void kona_pwmc_disable(struct pwm_chip *chip, struct pwm_device *pwm) value &= ~PRESCALE_MASK(chan); writel(value, kp->base + PRESCALE_OFFSET); - kona_pwmc_apply_settings(kp, chan); + ret = kona_pwmc_apply_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to prepare pwm settings: %d\n", ret); + return; + } clk_disable_unprepare(kp->clk); } @@ -256,14 +317,26 @@ static void kona_pwmc_disable(struct pwm_chip *chip, struct pwm_device *pwm) .owner = THIS_MODULE, }; +static const struct of_device_id bcm_kona_pwmc_dt[] = { + { .compatible = "brcm,kona-pwm", .data = (void *)KONA_PWM_V1}, + { .compatible = "brcm,kona-pwm-v2", .data = (void *)KONA_PWM_V2}, + { }, +}; +MODULE_DEVICE_TABLE(of, bcm_kona_pwmc_dt); + static int kona_pwmc_probe(struct platform_device *pdev) { struct kona_pwmc *kp; struct resource *res; + const struct of_device_id *of_id; unsigned int chan; unsigned int value = 0; int ret = 0; + of_id = of_match_node(bcm_kona_pwmc_dt, pdev->dev.of_node); + if (!of_id) + return -ENODEV; + kp = devm_kzalloc(&pdev->dev, sizeof(*kp), GFP_KERNEL); if (kp == NULL) return -ENOMEM; @@ -276,6 +349,7 @@ static int kona_pwmc_probe(struct platform_device *pdev) kp->chip.npwm = 6; kp->chip.of_xlate = of_pwm_xlate_with_flags; kp->chip.of_pwm_n_cells = 3; + kp->version = (enum kona_pwmc_ver)of_id->data; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); kp->base = devm_ioremap_resource(&pdev->dev, res); @@ -322,12 +396,6 @@ static int kona_pwmc_remove(struct platform_device *pdev) return pwmchip_remove(&kp->chip); } -static const struct of_device_id bcm_kona_pwmc_dt[] = { - { .compatible = "brcm,kona-pwm" }, - { }, -}; -MODULE_DEVICE_TABLE(of, bcm_kona_pwmc_dt); - static struct platform_driver kona_pwmc_driver = { .driver = { .name = "bcm-kona-pwm", -- 1.9.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH INTERNAL V3 2/3] drivers: pwm: pwm-bcm-kona: Add pwm-kona-v2 support @ 2019-01-11 5:08 ` Sheetal Tigadoli 0 siblings, 0 replies; 12+ messages in thread From: Sheetal Tigadoli @ 2019-01-11 5:08 UTC (permalink / raw) To: Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: linux-pwm, Sheetal Tigadoli, Praveen Kumar B, devicetree, linux-kernel, bcm-kernel-feedback-list, linux-arm-kernel From: Praveen Kumar B <praveen.b@broadcom.com> Add support for new version of pwm-kona. Add support to make PWM changes configured and stable. Signed-off-by: Praveen Kumar B <praveen.b@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com> --- drivers/pwm/pwm-bcm-kona.c | 128 ++++++++++++++++++++++++++++++++++----------- 1 file changed, 98 insertions(+), 30 deletions(-) diff --git a/drivers/pwm/pwm-bcm-kona.c b/drivers/pwm/pwm-bcm-kona.c index 09a95ae..2b44ad8 100644 --- a/drivers/pwm/pwm-bcm-kona.c +++ b/drivers/pwm/pwm-bcm-kona.c @@ -45,30 +45,39 @@ * high or low depending on its state at that exact instant. */ -#define PWM_CONTROL_OFFSET (0x00000000) +#define PWM_CONTROL_OFFSET 0x00000000 #define PWM_CONTROL_SMOOTH_SHIFT(chan) (24 + (chan)) #define PWM_CONTROL_TYPE_SHIFT(chan) (16 + (chan)) #define PWM_CONTROL_POLARITY_SHIFT(chan) (8 + (chan)) #define PWM_CONTROL_TRIGGER_SHIFT(chan) (chan) -#define PRESCALE_OFFSET (0x00000004) +#define PRESCALE_OFFSET 0x00000004 #define PRESCALE_SHIFT(chan) ((chan) << 2) #define PRESCALE_MASK(chan) (0x7 << PRESCALE_SHIFT(chan)) -#define PRESCALE_MIN (0x00000000) -#define PRESCALE_MAX (0x00000007) +#define PRESCALE_MIN 0x00000000 +#define PRESCALE_MAX 0x00000007 #define PERIOD_COUNT_OFFSET(chan) (0x00000008 + ((chan) << 3)) -#define PERIOD_COUNT_MIN (0x00000002) -#define PERIOD_COUNT_MAX (0x00ffffff) +#define PERIOD_COUNT_MIN 0x00000002 +#define PERIOD_COUNT_MAX 0x00ffffff #define DUTY_CYCLE_HIGH_OFFSET(chan) (0x0000000c + ((chan) << 3)) -#define DUTY_CYCLE_HIGH_MIN (0x00000000) -#define DUTY_CYCLE_HIGH_MAX (0x00ffffff) +#define DUTY_CYCLE_HIGH_MIN 0x00000000 +#define DUTY_CYCLE_HIGH_MAX 0x00ffffff + +#define PWM_MONITOR_OFFSET 0xb0 +#define PWM_MONITOR_TIMEOUT_US 5 + +enum kona_pwmc_ver { + KONA_PWM_V1 = 1, + KONA_PWM_V2 +}; struct kona_pwmc { struct pwm_chip chip; void __iomem *base; struct clk *clk; + enum kona_pwmc_ver version; }; static inline struct kona_pwmc *to_kona_pwmc(struct pwm_chip *_chip) @@ -76,11 +85,40 @@ static inline struct kona_pwmc *to_kona_pwmc(struct pwm_chip *_chip) return container_of(_chip, struct kona_pwmc, chip); } +static int kona_pwmc_wait_stable(struct pwm_chip *chip, unsigned int chan, + unsigned int kona_ver) +{ + struct kona_pwmc *kp = to_kona_pwmc(chip); + unsigned int value; + unsigned int count = PWM_MONITOR_TIMEOUT_US * 1000; + + switch (kona_ver) { + case KONA_PWM_V1: + /* + * There must be a min 400ns delay between clearing trigger and + * settingit. Failing to do this may result in no PWM signal. + */ + ndelay(400); + return 0; + case KONA_PWM_V2: + do { + value = readl(kp->base + PWM_MONITOR_OFFSET); + if (!(value & (BIT(chan)))) + return 0; + ndelay(1); + } while (count--); + + return -ETIMEDOUT; + default: + return -ENODEV; + } +} + /* * Clear trigger bit but set smooth bit to maintain old output. */ -static void kona_pwmc_prepare_for_settings(struct kona_pwmc *kp, - unsigned int chan) +static int kona_pwmc_prepare_for_settings(struct kona_pwmc *kp, + unsigned int chan) { unsigned int value = readl(kp->base + PWM_CONTROL_OFFSET); @@ -88,14 +126,10 @@ static void kona_pwmc_prepare_for_settings(struct kona_pwmc *kp, value &= ~(1 << PWM_CONTROL_TRIGGER_SHIFT(chan)); writel(value, kp->base + PWM_CONTROL_OFFSET); - /* - * There must be a min 400ns delay between clearing trigger and setting - * it. Failing to do this may result in no PWM signal. - */ - ndelay(400); + return kona_pwmc_wait_stable(&kp->chip, chan, kp->version); } -static void kona_pwmc_apply_settings(struct kona_pwmc *kp, unsigned int chan) +static int kona_pwmc_apply_settings(struct kona_pwmc *kp, unsigned int chan) { unsigned int value = readl(kp->base + PWM_CONTROL_OFFSET); @@ -104,8 +138,7 @@ static void kona_pwmc_apply_settings(struct kona_pwmc *kp, unsigned int chan) value |= 1 << PWM_CONTROL_TRIGGER_SHIFT(chan); writel(value, kp->base + PWM_CONTROL_OFFSET); - /* Trigger bit must be held high for at least 400 ns. */ - ndelay(400); + return kona_pwmc_wait_stable(&kp->chip, chan, kp->version); } static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm, @@ -115,6 +148,7 @@ static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm, u64 val, div, rate; unsigned long prescale = PRESCALE_MIN, pc, dc; unsigned int value, chan = pwm->hwpwm; + int ret; /* * Find period count, duty count and prescale to suit duty_ns and @@ -156,7 +190,12 @@ static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm, * validated immediately instead of on enable. */ if (pwm_is_enabled(pwm)) { - kona_pwmc_prepare_for_settings(kp, chan); + ret = kona_pwmc_prepare_for_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to prepare pwm settings: %d\n", + ret); + return ret; + } value = readl(kp->base + PRESCALE_OFFSET); value &= ~PRESCALE_MASK(chan); @@ -167,7 +206,12 @@ static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm, writel(dc, kp->base + DUTY_CYCLE_HIGH_OFFSET(chan)); - kona_pwmc_apply_settings(kp, chan); + ret = kona_pwmc_apply_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to apply settings: %d\n", + ret); + return ret; + } } return 0; @@ -187,7 +231,11 @@ static int kona_pwmc_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm, return ret; } - kona_pwmc_prepare_for_settings(kp, chan); + ret = kona_pwmc_prepare_for_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to prepare pwm settings: %d\n", ret); + return ret; + } value = readl(kp->base + PWM_CONTROL_OFFSET); @@ -198,7 +246,11 @@ static int kona_pwmc_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm, writel(value, kp->base + PWM_CONTROL_OFFSET); - kona_pwmc_apply_settings(kp, chan); + ret = kona_pwmc_apply_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to apply pwm settings: %d\n", ret); + return ret; + } clk_disable_unprepare(kp->clk); @@ -231,8 +283,13 @@ static void kona_pwmc_disable(struct pwm_chip *chip, struct pwm_device *pwm) struct kona_pwmc *kp = to_kona_pwmc(chip); unsigned int chan = pwm->hwpwm; unsigned int value; + int ret; - kona_pwmc_prepare_for_settings(kp, chan); + ret = kona_pwmc_prepare_for_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to prepare pwm settings: %d\n", ret); + return; + } /* Simulate a disable by configuring for zero duty */ writel(0, kp->base + DUTY_CYCLE_HIGH_OFFSET(chan)); @@ -243,7 +300,11 @@ static void kona_pwmc_disable(struct pwm_chip *chip, struct pwm_device *pwm) value &= ~PRESCALE_MASK(chan); writel(value, kp->base + PRESCALE_OFFSET); - kona_pwmc_apply_settings(kp, chan); + ret = kona_pwmc_apply_settings(kp, chan); + if (ret < 0) { + dev_err(chip->dev, "failed to prepare pwm settings: %d\n", ret); + return; + } clk_disable_unprepare(kp->clk); } @@ -256,14 +317,26 @@ static void kona_pwmc_disable(struct pwm_chip *chip, struct pwm_device *pwm) .owner = THIS_MODULE, }; +static const struct of_device_id bcm_kona_pwmc_dt[] = { + { .compatible = "brcm,kona-pwm", .data = (void *)KONA_PWM_V1}, + { .compatible = "brcm,kona-pwm-v2", .data = (void *)KONA_PWM_V2}, + { }, +}; +MODULE_DEVICE_TABLE(of, bcm_kona_pwmc_dt); + static int kona_pwmc_probe(struct platform_device *pdev) { struct kona_pwmc *kp; struct resource *res; + const struct of_device_id *of_id; unsigned int chan; unsigned int value = 0; int ret = 0; + of_id = of_match_node(bcm_kona_pwmc_dt, pdev->dev.of_node); + if (!of_id) + return -ENODEV; + kp = devm_kzalloc(&pdev->dev, sizeof(*kp), GFP_KERNEL); if (kp == NULL) return -ENOMEM; @@ -276,6 +349,7 @@ static int kona_pwmc_probe(struct platform_device *pdev) kp->chip.npwm = 6; kp->chip.of_xlate = of_pwm_xlate_with_flags; kp->chip.of_pwm_n_cells = 3; + kp->version = (enum kona_pwmc_ver)of_id->data; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); kp->base = devm_ioremap_resource(&pdev->dev, res); @@ -322,12 +396,6 @@ static int kona_pwmc_remove(struct platform_device *pdev) return pwmchip_remove(&kp->chip); } -static const struct of_device_id bcm_kona_pwmc_dt[] = { - { .compatible = "brcm,kona-pwm" }, - { }, -}; -MODULE_DEVICE_TABLE(of, bcm_kona_pwmc_dt); - static struct platform_driver kona_pwmc_driver = { .driver = { .name = "bcm-kona-pwm", -- 1.9.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH INTERNAL V3 3/3] ARM: dts: cygnus: Change pwm compatible to new version 2019-01-11 5:08 ` Sheetal Tigadoli @ 2019-01-11 5:08 ` Sheetal Tigadoli -1 siblings, 0 replies; 12+ messages in thread From: Sheetal Tigadoli @ 2019-01-11 5:08 UTC (permalink / raw) To: Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: bcm-kernel-feedback-list, linux-pwm, devicetree, linux-kernel, linux-arm-kernel, Praveen Kumar B, Sheetal Tigadoli From: Praveen Kumar B <praveen.b@broadcom.com> Change pwm compatible to new version of pwm-kona Add new compatible to check pwm configure status Signed-off-by: Praveen Kumar B <praveen.b@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com> --- arch/arm/boot/dts/bcm-cygnus.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi index 253df71..2a433e7 100644 --- a/arch/arm/boot/dts/bcm-cygnus.dtsi +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi @@ -595,7 +595,7 @@ }; pwm: pwm@180aa500 { - compatible = "brcm,kona-pwm"; + compatible = "brcm,kona-pwm-v2"; reg = <0x180aa500 0xc4>; #pwm-cells = <3>; clocks = <&asiu_clks BCM_CYGNUS_ASIU_PWM_CLK>; -- 1.9.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH INTERNAL V3 3/3] ARM: dts: cygnus: Change pwm compatible to new version @ 2019-01-11 5:08 ` Sheetal Tigadoli 0 siblings, 0 replies; 12+ messages in thread From: Sheetal Tigadoli @ 2019-01-11 5:08 UTC (permalink / raw) To: Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: linux-pwm, Sheetal Tigadoli, Praveen Kumar B, devicetree, linux-kernel, bcm-kernel-feedback-list, linux-arm-kernel From: Praveen Kumar B <praveen.b@broadcom.com> Change pwm compatible to new version of pwm-kona Add new compatible to check pwm configure status Signed-off-by: Praveen Kumar B <praveen.b@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com> --- arch/arm/boot/dts/bcm-cygnus.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi index 253df71..2a433e7 100644 --- a/arch/arm/boot/dts/bcm-cygnus.dtsi +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi @@ -595,7 +595,7 @@ }; pwm: pwm@180aa500 { - compatible = "brcm,kona-pwm"; + compatible = "brcm,kona-pwm-v2"; reg = <0x180aa500 0xc4>; #pwm-cells = <3>; clocks = <&asiu_clks BCM_CYGNUS_ASIU_PWM_CLK>; -- 1.9.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH INTERNAL V3 0/3] Add support for PWM Configure and stablize for PWM kona 2019-01-11 5:08 ` Sheetal Tigadoli @ 2019-01-11 23:58 ` Ray Jui -1 siblings, 0 replies; 12+ messages in thread From: Ray Jui @ 2019-01-11 23:58 UTC (permalink / raw) To: Sheetal Tigadoli, Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: bcm-kernel-feedback-list, linux-pwm, devicetree, linux-kernel, linux-arm-kernel Please remove 'INTERNAL' in all of your patches and cover letter. On 1/10/2019 9:08 PM, Sheetal Tigadoli wrote: > Hi, > This patchset contain support to make PWM changes configure > and stablize > Following are brief changes done > a. Add support for version2 compatible string > b. Change PWM config and stablize delay in PWM Kona > > Praveen Kumar B (3): > dt-bindings: pwm: kona: Add new compatible for new version pwm-kona > drivers: pwm: pwm-bcm-kona: Add pwm-kona-v2 support > ARM: dts: cygnus: Change pwm compatible to new version > > .../devicetree/bindings/pwm/brcm,kona-pwm.txt | 2 +- > arch/arm/boot/dts/bcm-cygnus.dtsi | 2 +- > drivers/pwm/pwm-bcm-kona.c | 128 ++++++++++++++++----- > 3 files changed, 100 insertions(+), 32 deletions(-) > ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH INTERNAL V3 0/3] Add support for PWM Configure and stablize for PWM kona @ 2019-01-11 23:58 ` Ray Jui 0 siblings, 0 replies; 12+ messages in thread From: Ray Jui @ 2019-01-11 23:58 UTC (permalink / raw) To: Sheetal Tigadoli, Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: linux-pwm, bcm-kernel-feedback-list, linux-kernel, linux-arm-kernel, devicetree Please remove 'INTERNAL' in all of your patches and cover letter. On 1/10/2019 9:08 PM, Sheetal Tigadoli wrote: > Hi, > This patchset contain support to make PWM changes configure > and stablize > Following are brief changes done > a. Add support for version2 compatible string > b. Change PWM config and stablize delay in PWM Kona > > Praveen Kumar B (3): > dt-bindings: pwm: kona: Add new compatible for new version pwm-kona > drivers: pwm: pwm-bcm-kona: Add pwm-kona-v2 support > ARM: dts: cygnus: Change pwm compatible to new version > > .../devicetree/bindings/pwm/brcm,kona-pwm.txt | 2 +- > arch/arm/boot/dts/bcm-cygnus.dtsi | 2 +- > drivers/pwm/pwm-bcm-kona.c | 128 ++++++++++++++++----- > 3 files changed, 100 insertions(+), 32 deletions(-) > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH INTERNAL V3 0/3] Add support for PWM Configure and stablize for PWM kona 2019-01-11 23:58 ` Ray Jui @ 2019-01-12 0:00 ` Ray Jui -1 siblings, 0 replies; 12+ messages in thread From: Ray Jui @ 2019-01-12 0:00 UTC (permalink / raw) To: Sheetal Tigadoli, Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: bcm-kernel-feedback-list, linux-pwm, devicetree, linux-kernel, linux-arm-kernel On 1/11/2019 3:58 PM, Ray Jui wrote: > Please remove 'INTERNAL' in all of your patches and cover letter. > Never mind, saw your next patchset with this issue fixed.... > On 1/10/2019 9:08 PM, Sheetal Tigadoli wrote: >> Hi, >> This patchset contain support to make PWM changes configure >> and stablize >> Following are brief changes done >> a. Add support for version2 compatible string >> b. Change PWM config and stablize delay in PWM Kona >> >> Praveen Kumar B (3): >> dt-bindings: pwm: kona: Add new compatible for new version pwm-kona >> drivers: pwm: pwm-bcm-kona: Add pwm-kona-v2 support >> ARM: dts: cygnus: Change pwm compatible to new version >> >> .../devicetree/bindings/pwm/brcm,kona-pwm.txt | 2 +- >> arch/arm/boot/dts/bcm-cygnus.dtsi | 2 +- >> drivers/pwm/pwm-bcm-kona.c | 128 ++++++++++++++++----- >> 3 files changed, 100 insertions(+), 32 deletions(-) >> ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH INTERNAL V3 0/3] Add support for PWM Configure and stablize for PWM kona @ 2019-01-12 0:00 ` Ray Jui 0 siblings, 0 replies; 12+ messages in thread From: Ray Jui @ 2019-01-12 0:00 UTC (permalink / raw) To: Sheetal Tigadoli, Thierry Reding, Rob Herring, Florian Fainelli, Ray Jui, Scott Branden Cc: linux-pwm, bcm-kernel-feedback-list, linux-kernel, linux-arm-kernel, devicetree On 1/11/2019 3:58 PM, Ray Jui wrote: > Please remove 'INTERNAL' in all of your patches and cover letter. > Never mind, saw your next patchset with this issue fixed.... > On 1/10/2019 9:08 PM, Sheetal Tigadoli wrote: >> Hi, >> This patchset contain support to make PWM changes configure >> and stablize >> Following are brief changes done >> a. Add support for version2 compatible string >> b. Change PWM config and stablize delay in PWM Kona >> >> Praveen Kumar B (3): >> dt-bindings: pwm: kona: Add new compatible for new version pwm-kona >> drivers: pwm: pwm-bcm-kona: Add pwm-kona-v2 support >> ARM: dts: cygnus: Change pwm compatible to new version >> >> .../devicetree/bindings/pwm/brcm,kona-pwm.txt | 2 +- >> arch/arm/boot/dts/bcm-cygnus.dtsi | 2 +- >> drivers/pwm/pwm-bcm-kona.c | 128 ++++++++++++++++----- >> 3 files changed, 100 insertions(+), 32 deletions(-) >> _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2019-01-12 0:00 UTC | newest] Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2019-01-11 5:08 [PATCH INTERNAL V3 0/3] Add support for PWM Configure and stablize for PWM kona Sheetal Tigadoli 2019-01-11 5:08 ` Sheetal Tigadoli 2019-01-11 5:08 ` [PATCH INTERNAL V3 1/3] dt-bindings: pwm: kona: Add new compatible for new version pwm-kona Sheetal Tigadoli 2019-01-11 5:08 ` Sheetal Tigadoli 2019-01-11 5:08 ` [PATCH INTERNAL V3 2/3] drivers: pwm: pwm-bcm-kona: Add pwm-kona-v2 support Sheetal Tigadoli 2019-01-11 5:08 ` Sheetal Tigadoli 2019-01-11 5:08 ` [PATCH INTERNAL V3 3/3] ARM: dts: cygnus: Change pwm compatible to new version Sheetal Tigadoli 2019-01-11 5:08 ` Sheetal Tigadoli 2019-01-11 23:58 ` [PATCH INTERNAL V3 0/3] Add support for PWM Configure and stablize for PWM kona Ray Jui 2019-01-11 23:58 ` Ray Jui 2019-01-12 0:00 ` Ray Jui 2019-01-12 0:00 ` Ray Jui
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.