All of lore.kernel.org
 help / color / mirror / Atom feed
From: Zhang Run <zhang.run@zte.com.cn>
To: davem@davemloft.net
Cc: marcel.ziswiler@toradex.com, lynxis@fe80.eu,
	linux-usb@vger.kernel.org, netdev@vger.kernel.org,
	linux-kernel@vger.kernel.org, xue.zhihong@zte.com.cn,
	wang.yi59@zte.com.cn, Zhang Run <zhang.run@zte.com.cn>
Subject: [PATCH] net: usb: asix: ax88772_bind return error when hw_reset fail
Date: Thu, 24 Jan 2019 13:48:49 +0800	[thread overview]
Message-ID: <1548308929-7727-1-git-send-email-zhang.run@zte.com.cn> (raw)

The ax88772_bind() should return error code immediately when the PHY
was not reset properly through ax88772a_hw_reset().
Otherwise, The asix_get_phyid() will block when get the PHY 
Identifier from the PHYSID1 MII registers through asix_mdio_read() 
due to the PHY isn't ready. Furthermore, it will produce a lot of 
error message cause system crash.As follows:
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to send
 software reset: ffffffb9
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
 software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
 software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
 reg index 0x0000: -71
... 

Signed-off-by: Zhang Run <zhang.run@zte.com.cn>
Reviewed-by: Yang Wei <yang.wei9@zte.com.cn>
---
 drivers/net/usb/asix_devices.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index b654f05..3d93993 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -739,8 +739,13 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &chipcode, 0);
 	chipcode &= AX_CHIPCODE_MASK;
 
-	(chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
-					    ax88772a_hw_reset(dev, 0);
+	ret = (chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
+						  ax88772a_hw_reset(dev, 0);
+
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Failed to reset AX88772: %d\n", ret);
+		return ret;
+	}
 
 	/* Read PHYID register *AFTER* the PHY was reset properly */
 	phyid = asix_get_phyid(dev);
-- 
2.7.4


WARNING: multiple messages have this Message-ID (diff)
From: Zhang Run <zhang.run@zte.com.cn>
To: davem@davemloft.net
Cc: marcel.ziswiler@toradex.com, lynxis@fe80.eu,
	linux-usb@vger.kernel.org, netdev@vger.kernel.org,
	linux-kernel@vger.kernel.org, xue.zhihong@zte.com.cn,
	wang.yi59@zte.com.cn, Zhang Run <zhang.run@zte.com.cn>
Subject: net: usb: asix: ax88772_bind return error when hw_reset fail
Date: Thu, 24 Jan 2019 13:48:49 +0800	[thread overview]
Message-ID: <1548308929-7727-1-git-send-email-zhang.run@zte.com.cn> (raw)

The ax88772_bind() should return error code immediately when the PHY
was not reset properly through ax88772a_hw_reset().
Otherwise, The asix_get_phyid() will block when get the PHY 
Identifier from the PHYSID1 MII registers through asix_mdio_read() 
due to the PHY isn't ready. Furthermore, it will produce a lot of 
error message cause system crash.As follows:
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to send
 software reset: ffffffb9
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
 software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
 software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
 reg index 0x0000: -71
... 

Signed-off-by: Zhang Run <zhang.run@zte.com.cn>
Reviewed-by: Yang Wei <yang.wei9@zte.com.cn>
---
 drivers/net/usb/asix_devices.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
index b654f05..3d93993 100644
--- a/drivers/net/usb/asix_devices.c
+++ b/drivers/net/usb/asix_devices.c
@@ -739,8 +739,13 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
 	asix_read_cmd(dev, AX_CMD_STATMNGSTS_REG, 0, 0, 1, &chipcode, 0);
 	chipcode &= AX_CHIPCODE_MASK;
 
-	(chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
-					    ax88772a_hw_reset(dev, 0);
+	ret = (chipcode == AX_AX88772_CHIPCODE) ? ax88772_hw_reset(dev, 0) :
+						  ax88772a_hw_reset(dev, 0);
+
+	if (ret < 0) {
+		netdev_dbg(dev->net, "Failed to reset AX88772: %d\n", ret);
+		return ret;
+	}
 
 	/* Read PHYID register *AFTER* the PHY was reset properly */
 	phyid = asix_get_phyid(dev);

             reply	other threads:[~2019-01-24  5:49 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-01-24  5:48 Zhang Run [this message]
2019-01-24  5:48 ` net: usb: asix: ax88772_bind return error when hw_reset fail Zhang Run
2019-01-24 14:03 ` [PATCH] " Marcel Ziswiler
2019-01-24 14:03   ` Marcel Ziswiler
2019-01-25  6:33 ` [PATCH] " David Miller
2019-01-25  6:33   ` David Miller

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1548308929-7727-1-git-send-email-zhang.run@zte.com.cn \
    --to=zhang.run@zte.com.cn \
    --cc=davem@davemloft.net \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=lynxis@fe80.eu \
    --cc=marcel.ziswiler@toradex.com \
    --cc=netdev@vger.kernel.org \
    --cc=wang.yi59@zte.com.cn \
    --cc=xue.zhihong@zte.com.cn \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.