From: <Claudiu.Beznea@microchip.com>
To: linus.walleij@linaro.org, robh+dt@kernel.org,
mark.rutland@arm.com, Nicolas.Ferre@microchip.com,
alexandre.belloni@bootlin.com, Ludovic.Desroches@microchip.com
Cc: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, Claudiu.Beznea@microchip.com
Subject: [PATCH v2 0/7] add support for SAM9X60 pin controller
Date: Thu, 31 Jan 2019 16:18:00 +0000 [thread overview]
Message-ID: <1548951466-26297-1-git-send-email-claudiu.beznea@microchip.com> (raw)
From: Claudiu Beznea <claudiu.beznea@microchip.com>
This series adds drive strenght and slew rate support for SAMX60's pin
controller. For drive strenght we could have 2 values: low, high.
For slew rate we could have 2 values: enable, disabled.
Besides this I took the chance and adapt the documentation for at91 pinctrl
driver.
Changes in v2:
- s/microchip,sam9x60-pictrl/microchip,sam9x60-pinctrl in patches 3/7, 5/7
Claudiu Beznea (7):
pinctrl: at91: add option to use drive strength bits
pinctrl: at91: add drive strength support for SAM9X60
pinctrl: at91: add compatibles for SAM9X60 pin controller
dt-bindings: add documentation for banks
dt-bindings: add bindings for SAM9X60
pinctrl: at91: add slewrate support for SAM9X60
dt-bindings: add documentation for slew rate
.../bindings/pinctrl/atmel,at91-pinctrl.txt | 27 ++++-
drivers/pinctrl/pinctrl-at91.c | 134 +++++++++++++++++++--
drivers/pinctrl/pinctrl-at91.h | 3 +
include/dt-bindings/pinctrl/at91.h | 4 +
4 files changed, 155 insertions(+), 13 deletions(-)
--
2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: <Claudiu.Beznea@microchip.com>
To: <linus.walleij@linaro.org>, <robh+dt@kernel.org>,
<mark.rutland@arm.com>, <Nicolas.Ferre@microchip.com>,
<alexandre.belloni@bootlin.com>,
<Ludovic.Desroches@microchip.com>
Cc: <linux-gpio@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <Claudiu.Beznea@microchip.com>
Subject: [PATCH v2 0/7] add support for SAM9X60 pin controller
Date: Thu, 31 Jan 2019 16:18:00 +0000 [thread overview]
Message-ID: <1548951466-26297-1-git-send-email-claudiu.beznea@microchip.com> (raw)
From: Claudiu Beznea <claudiu.beznea@microchip.com>
This series adds drive strenght and slew rate support for SAMX60's pin
controller. For drive strenght we could have 2 values: low, high.
For slew rate we could have 2 values: enable, disabled.
Besides this I took the chance and adapt the documentation for at91 pinctrl
driver.
Changes in v2:
- s/microchip,sam9x60-pictrl/microchip,sam9x60-pinctrl in patches 3/7, 5/7
Claudiu Beznea (7):
pinctrl: at91: add option to use drive strength bits
pinctrl: at91: add drive strength support for SAM9X60
pinctrl: at91: add compatibles for SAM9X60 pin controller
dt-bindings: add documentation for banks
dt-bindings: add bindings for SAM9X60
pinctrl: at91: add slewrate support for SAM9X60
dt-bindings: add documentation for slew rate
.../bindings/pinctrl/atmel,at91-pinctrl.txt | 27 ++++-
drivers/pinctrl/pinctrl-at91.c | 134 +++++++++++++++++++--
drivers/pinctrl/pinctrl-at91.h | 3 +
include/dt-bindings/pinctrl/at91.h | 4 +
4 files changed, 155 insertions(+), 13 deletions(-)
--
2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: <Claudiu.Beznea@microchip.com>
To: <linus.walleij@linaro.org>, <robh+dt@kernel.org>,
<mark.rutland@arm.com>, <Nicolas.Ferre@microchip.com>,
<alexandre.belloni@bootlin.com>,
<Ludovic.Desroches@microchip.com>
Cc: linux-gpio@vger.kernel.org, Claudiu.Beznea@microchip.com,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org
Subject: [PATCH v2 0/7] add support for SAM9X60 pin controller
Date: Thu, 31 Jan 2019 16:18:00 +0000 [thread overview]
Message-ID: <1548951466-26297-1-git-send-email-claudiu.beznea@microchip.com> (raw)
From: Claudiu Beznea <claudiu.beznea@microchip.com>
This series adds drive strenght and slew rate support for SAMX60's pin
controller. For drive strenght we could have 2 values: low, high.
For slew rate we could have 2 values: enable, disabled.
Besides this I took the chance and adapt the documentation for at91 pinctrl
driver.
Changes in v2:
- s/microchip,sam9x60-pictrl/microchip,sam9x60-pinctrl in patches 3/7, 5/7
Claudiu Beznea (7):
pinctrl: at91: add option to use drive strength bits
pinctrl: at91: add drive strength support for SAM9X60
pinctrl: at91: add compatibles for SAM9X60 pin controller
dt-bindings: add documentation for banks
dt-bindings: add bindings for SAM9X60
pinctrl: at91: add slewrate support for SAM9X60
dt-bindings: add documentation for slew rate
.../bindings/pinctrl/atmel,at91-pinctrl.txt | 27 ++++-
drivers/pinctrl/pinctrl-at91.c | 134 +++++++++++++++++++--
drivers/pinctrl/pinctrl-at91.h | 3 +
include/dt-bindings/pinctrl/at91.h | 4 +
4 files changed, 155 insertions(+), 13 deletions(-)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2019-01-31 16:18 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-31 16:18 Claudiu.Beznea [this message]
2019-01-31 16:18 ` [PATCH v2 0/7] add support for SAM9X60 pin controller Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` [PATCH v2 1/7] pinctrl: at91: add option to use drive strength bits Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-02-06 8:13 ` Ludovic Desroches
2019-02-06 8:13 ` Ludovic Desroches
2019-02-06 8:13 ` Ludovic Desroches
2019-02-06 9:46 ` Claudiu.Beznea
2019-02-06 9:46 ` Claudiu.Beznea
2019-02-06 9:46 ` Claudiu.Beznea
2019-02-06 10:24 ` Ludovic Desroches
2019-02-06 10:24 ` Ludovic Desroches
2019-02-06 10:24 ` Ludovic Desroches
2019-02-06 13:46 ` Claudiu.Beznea
2019-02-06 13:46 ` Claudiu.Beznea
2019-02-06 13:46 ` Claudiu.Beznea
2019-01-31 16:18 ` [PATCH v2 2/7] pinctrl: at91: add drive strength support for SAM9X60 Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` [PATCH v2 3/7] pinctrl: at91: add compatibles for SAM9X60 pin controller Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` [PATCH v2 4/7] dt-bindings: add documentation for banks Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` [PATCH v2 5/7] dt-bindings: add bindings for SAM9X60 Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` [PATCH v2 6/7] pinctrl: at91: add slewrate support " Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` [PATCH v2 7/7] dt-bindings: add documentation for slew rate Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-01-31 16:18 ` Claudiu.Beznea
2019-02-06 8:56 ` [PATCH v2 0/7] add support for SAM9X60 pin controller Ludovic Desroches
2019-02-06 8:56 ` Ludovic Desroches
2019-02-06 8:56 ` Ludovic Desroches
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1548951466-26297-1-git-send-email-claudiu.beznea@microchip.com \
--to=claudiu.beznea@microchip.com \
--cc=Ludovic.Desroches@microchip.com \
--cc=Nicolas.Ferre@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.