All of lore.kernel.org
 help / color / mirror / Atom feed
From: Mason Yang <masonccyang@mxic.com.tw>
To: broonie@kernel.org, miquel.raynal@bootlin.com, richard@nod.at,
	marek.vasut@gmail.com, dwmw2@infradead.org,
	computersforpeace@gmail.com, vigneshr@ti.com,
	bbrezillon@kernel.org, tudor.ambarus@microchip.com
Cc: juliensu@mxic.com.tw, linux-kernel@vger.kernel.org,
	linux-mtd@lists.infradead.org, linux-spi@vger.kernel.org,
	Mason Yang <masonccyang@mxic.com.tw>
Subject: [PATCH 4/4] spi: mxic: Add support for Octal 8D-8D-8D mode
Date: Fri, 15 Nov 2019 16:58:08 +0800	[thread overview]
Message-ID: <1573808288-19365-5-git-send-email-masonccyang@mxic.com.tw> (raw)
In-Reply-To: <1573808288-19365-1-git-send-email-masonccyang@mxic.com.tw>

patch driver for 8-8-8 and 8D-8D-8D mode support.

Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
---
 drivers/spi/spi-mxic.c | 98 ++++++++++++++++++++++++++++++++++----------------
 1 file changed, 67 insertions(+), 31 deletions(-)

diff --git a/drivers/spi/spi-mxic.c b/drivers/spi/spi-mxic.c
index f48563c..50e2055 100644
--- a/drivers/spi/spi-mxic.c
+++ b/drivers/spi/spi-mxic.c
@@ -280,10 +280,58 @@ static void mxic_spi_hw_init(struct mxic_spi *mxic)
 	       mxic->regs + HC_CFG);
 }
 
+static u32 mxic_spi_mem_prep_op_cfg(const struct spi_mem_op *op)
+{
+	u32 cfg =  OP_CMD_BYTES(op->cmd.nbytes) |
+		   OP_CMD_BUSW(fls(op->cmd.buswidth) - 1) |
+		   (op->cmd.dtr ? OP_CMD_DDR : 0);
+
+	if (op->addr.nbytes)
+		cfg |= OP_ADDR_BYTES(op->addr.nbytes) |
+		       OP_ADDR_BUSW(fls(op->addr.buswidth) - 1) |
+		       (op->addr.dtr ? OP_ADDR_DDR : 0);
+
+	if (op->dummy.nbytes)
+		cfg |= OP_DUMMY_CYC(op->dummy.nbytes);
+
+	if (op->data.nbytes) {
+		cfg |= OP_DATA_BUSW(fls(op->data.buswidth) - 1) |
+		      (op->data.dtr ? OP_DATA_DDR : 0);
+		if (op->data.dir == SPI_MEM_DATA_IN) {
+			cfg |= OP_READ;
+			if (op->data.dtr == OP_DATA_DDR)
+				cfg |= OP_DQS_EN;
+		}
+	}
+
+	return cfg;
+}
+
+static void mxic_spi_set_hc_cfg(struct spi_device *spi, u32 flags)
+{
+	struct mxic_spi *mxic = spi_master_get_devdata(spi->master);
+	int nio = 1;
+
+	if (spi->mode & (SPI_RX_OCTAL | SPI_TX_OCTAL))
+		nio = 8;
+	else if (spi->mode & (SPI_TX_QUAD | SPI_RX_QUAD))
+		nio = 4;
+	else if (spi->mode & (SPI_TX_DUAL | SPI_RX_DUAL))
+		nio = 2;
+
+	writel(flags | HC_CFG_NIO(nio) |
+	       HC_CFG_TYPE(spi->chip_select, HC_CFG_TYPE_SPI_NOR) |
+	       HC_CFG_SLV_ACT(spi->chip_select) | HC_CFG_IDLE_SIO_LVL(1),
+	       mxic->regs + HC_CFG);
+}
+
 static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf,
 			      void *rxbuf, unsigned int len)
 {
 	unsigned int pos = 0;
+	bool dtr_enabled;
+
+	dtr_enabled = (readl(mxic->regs + SS_CTRL(0)) & OP_DATA_DDR);
 
 	while (pos < len) {
 		unsigned int nbytes = len - pos;
@@ -302,6 +350,9 @@ static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf,
 		if (ret)
 			return ret;
 
+		if (dtr_enabled && len & 0x1)
+			nbytes++;
+
 		writel(data, mxic->regs + TXD(nbytes % 4));
 
 		if (rxbuf) {
@@ -319,6 +370,8 @@ static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf,
 
 			data = readl(mxic->regs + RXD);
 			data >>= (8 * (4 - nbytes));
+			if (dtr_enabled && len & 0x1)
+				nbytes++;
 			memcpy(rxbuf + pos, &data, nbytes);
 			WARN_ON(readl(mxic->regs + INT_STS) & INT_RX_NOT_EMPTY);
 		} else {
@@ -335,8 +388,8 @@ static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf,
 static bool mxic_spi_mem_supports_op(struct spi_mem *mem,
 				     const struct spi_mem_op *op)
 {
-	if (op->data.buswidth > 4 || op->addr.buswidth > 4 ||
-	    op->dummy.buswidth > 4 || op->cmd.buswidth > 4)
+	if (op->data.buswidth > 8 || op->addr.buswidth > 8 ||
+	    op->dummy.buswidth > 8 || op->cmd.buswidth > 8)
 		return false;
 
 	if (op->data.nbytes && op->dummy.nbytes &&
@@ -353,47 +406,29 @@ static int mxic_spi_mem_exec_op(struct spi_mem *mem,
 				const struct spi_mem_op *op)
 {
 	struct mxic_spi *mxic = spi_master_get_devdata(mem->spi->master);
-	int nio = 1, i, ret;
-	u32 ss_ctrl;
+	int i, ret;
 	u8 addr[8];
+	u8 cmd[2];
 
 	ret = mxic_spi_set_freq(mxic, mem->spi->max_speed_hz);
 	if (ret)
 		return ret;
 
-	if (mem->spi->mode & (SPI_TX_QUAD | SPI_RX_QUAD))
-		nio = 4;
-	else if (mem->spi->mode & (SPI_TX_DUAL | SPI_RX_DUAL))
-		nio = 2;
+	mxic_spi_set_hc_cfg(mem->spi, HC_CFG_MAN_CS_EN);
 
-	writel(HC_CFG_NIO(nio) |
-	       HC_CFG_TYPE(mem->spi->chip_select, HC_CFG_TYPE_SPI_NOR) |
-	       HC_CFG_SLV_ACT(mem->spi->chip_select) | HC_CFG_IDLE_SIO_LVL(1) |
-	       HC_CFG_MAN_CS_EN,
-	       mxic->regs + HC_CFG);
 	writel(HC_EN_BIT, mxic->regs + HC_EN);
 
-	ss_ctrl = OP_CMD_BYTES(1) | OP_CMD_BUSW(fls(op->cmd.buswidth) - 1);
-
-	if (op->addr.nbytes)
-		ss_ctrl |= OP_ADDR_BYTES(op->addr.nbytes) |
-			   OP_ADDR_BUSW(fls(op->addr.buswidth) - 1);
-
-	if (op->dummy.nbytes)
-		ss_ctrl |= OP_DUMMY_CYC(op->dummy.nbytes);
-
-	if (op->data.nbytes) {
-		ss_ctrl |= OP_DATA_BUSW(fls(op->data.buswidth) - 1);
-		if (op->data.dir == SPI_MEM_DATA_IN)
-			ss_ctrl |= OP_READ;
-	}
-
-	writel(ss_ctrl, mxic->regs + SS_CTRL(mem->spi->chip_select));
+	writel(mxic_spi_mem_prep_op_cfg(op),
+	       mxic->regs + SS_CTRL(mem->spi->chip_select));
 
 	writel(readl(mxic->regs + HC_CFG) | HC_CFG_MAN_CS_ASSERT,
 	       mxic->regs + HC_CFG);
 
-	ret = mxic_spi_data_xfer(mxic, &op->cmd.opcode, NULL, 1);
+	cmd[0] = op->cmd.opcode;
+	if (op->cmd.nbytes == 2)
+		cmd[1] = op->cmd.ext_opcode;
+
+	ret = mxic_spi_data_xfer(mxic, cmd, NULL, op->cmd.nbytes);
 	if (ret)
 		goto out;
 
@@ -566,7 +601,8 @@ static int mxic_spi_probe(struct platform_device *pdev)
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
 	master->mode_bits = SPI_CPOL | SPI_CPHA |
 			SPI_RX_DUAL | SPI_TX_DUAL |
-			SPI_RX_QUAD | SPI_TX_QUAD;
+			SPI_RX_QUAD | SPI_TX_QUAD |
+			SPI_RX_OCTAL | SPI_TX_OCTAL;
 
 	mxic_spi_hw_init(mxic);
 
-- 
1.9.1


WARNING: multiple messages have this Message-ID (diff)
From: Mason Yang <masonccyang@mxic.com.tw>
To: broonie@kernel.org, miquel.raynal@bootlin.com, richard@nod.at,
	marek.vasut@gmail.com, dwmw2@infradead.org,
	computersforpeace@gmail.com, vigneshr@ti.com,
	bbrezillon@kernel.org, tudor.ambarus@microchip.com
Cc: juliensu@mxic.com.tw, Mason Yang <masonccyang@mxic.com.tw>,
	linux-mtd@lists.infradead.org, linux-kernel@vger.kernel.org,
	linux-spi@vger.kernel.org
Subject: [PATCH 4/4] spi: mxic: Add support for Octal 8D-8D-8D mode
Date: Fri, 15 Nov 2019 16:58:08 +0800	[thread overview]
Message-ID: <1573808288-19365-5-git-send-email-masonccyang@mxic.com.tw> (raw)
In-Reply-To: <1573808288-19365-1-git-send-email-masonccyang@mxic.com.tw>

patch driver for 8-8-8 and 8D-8D-8D mode support.

Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
---
 drivers/spi/spi-mxic.c | 98 ++++++++++++++++++++++++++++++++++----------------
 1 file changed, 67 insertions(+), 31 deletions(-)

diff --git a/drivers/spi/spi-mxic.c b/drivers/spi/spi-mxic.c
index f48563c..50e2055 100644
--- a/drivers/spi/spi-mxic.c
+++ b/drivers/spi/spi-mxic.c
@@ -280,10 +280,58 @@ static void mxic_spi_hw_init(struct mxic_spi *mxic)
 	       mxic->regs + HC_CFG);
 }
 
+static u32 mxic_spi_mem_prep_op_cfg(const struct spi_mem_op *op)
+{
+	u32 cfg =  OP_CMD_BYTES(op->cmd.nbytes) |
+		   OP_CMD_BUSW(fls(op->cmd.buswidth) - 1) |
+		   (op->cmd.dtr ? OP_CMD_DDR : 0);
+
+	if (op->addr.nbytes)
+		cfg |= OP_ADDR_BYTES(op->addr.nbytes) |
+		       OP_ADDR_BUSW(fls(op->addr.buswidth) - 1) |
+		       (op->addr.dtr ? OP_ADDR_DDR : 0);
+
+	if (op->dummy.nbytes)
+		cfg |= OP_DUMMY_CYC(op->dummy.nbytes);
+
+	if (op->data.nbytes) {
+		cfg |= OP_DATA_BUSW(fls(op->data.buswidth) - 1) |
+		      (op->data.dtr ? OP_DATA_DDR : 0);
+		if (op->data.dir == SPI_MEM_DATA_IN) {
+			cfg |= OP_READ;
+			if (op->data.dtr == OP_DATA_DDR)
+				cfg |= OP_DQS_EN;
+		}
+	}
+
+	return cfg;
+}
+
+static void mxic_spi_set_hc_cfg(struct spi_device *spi, u32 flags)
+{
+	struct mxic_spi *mxic = spi_master_get_devdata(spi->master);
+	int nio = 1;
+
+	if (spi->mode & (SPI_RX_OCTAL | SPI_TX_OCTAL))
+		nio = 8;
+	else if (spi->mode & (SPI_TX_QUAD | SPI_RX_QUAD))
+		nio = 4;
+	else if (spi->mode & (SPI_TX_DUAL | SPI_RX_DUAL))
+		nio = 2;
+
+	writel(flags | HC_CFG_NIO(nio) |
+	       HC_CFG_TYPE(spi->chip_select, HC_CFG_TYPE_SPI_NOR) |
+	       HC_CFG_SLV_ACT(spi->chip_select) | HC_CFG_IDLE_SIO_LVL(1),
+	       mxic->regs + HC_CFG);
+}
+
 static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf,
 			      void *rxbuf, unsigned int len)
 {
 	unsigned int pos = 0;
+	bool dtr_enabled;
+
+	dtr_enabled = (readl(mxic->regs + SS_CTRL(0)) & OP_DATA_DDR);
 
 	while (pos < len) {
 		unsigned int nbytes = len - pos;
@@ -302,6 +350,9 @@ static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf,
 		if (ret)
 			return ret;
 
+		if (dtr_enabled && len & 0x1)
+			nbytes++;
+
 		writel(data, mxic->regs + TXD(nbytes % 4));
 
 		if (rxbuf) {
@@ -319,6 +370,8 @@ static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf,
 
 			data = readl(mxic->regs + RXD);
 			data >>= (8 * (4 - nbytes));
+			if (dtr_enabled && len & 0x1)
+				nbytes++;
 			memcpy(rxbuf + pos, &data, nbytes);
 			WARN_ON(readl(mxic->regs + INT_STS) & INT_RX_NOT_EMPTY);
 		} else {
@@ -335,8 +388,8 @@ static int mxic_spi_data_xfer(struct mxic_spi *mxic, const void *txbuf,
 static bool mxic_spi_mem_supports_op(struct spi_mem *mem,
 				     const struct spi_mem_op *op)
 {
-	if (op->data.buswidth > 4 || op->addr.buswidth > 4 ||
-	    op->dummy.buswidth > 4 || op->cmd.buswidth > 4)
+	if (op->data.buswidth > 8 || op->addr.buswidth > 8 ||
+	    op->dummy.buswidth > 8 || op->cmd.buswidth > 8)
 		return false;
 
 	if (op->data.nbytes && op->dummy.nbytes &&
@@ -353,47 +406,29 @@ static int mxic_spi_mem_exec_op(struct spi_mem *mem,
 				const struct spi_mem_op *op)
 {
 	struct mxic_spi *mxic = spi_master_get_devdata(mem->spi->master);
-	int nio = 1, i, ret;
-	u32 ss_ctrl;
+	int i, ret;
 	u8 addr[8];
+	u8 cmd[2];
 
 	ret = mxic_spi_set_freq(mxic, mem->spi->max_speed_hz);
 	if (ret)
 		return ret;
 
-	if (mem->spi->mode & (SPI_TX_QUAD | SPI_RX_QUAD))
-		nio = 4;
-	else if (mem->spi->mode & (SPI_TX_DUAL | SPI_RX_DUAL))
-		nio = 2;
+	mxic_spi_set_hc_cfg(mem->spi, HC_CFG_MAN_CS_EN);
 
-	writel(HC_CFG_NIO(nio) |
-	       HC_CFG_TYPE(mem->spi->chip_select, HC_CFG_TYPE_SPI_NOR) |
-	       HC_CFG_SLV_ACT(mem->spi->chip_select) | HC_CFG_IDLE_SIO_LVL(1) |
-	       HC_CFG_MAN_CS_EN,
-	       mxic->regs + HC_CFG);
 	writel(HC_EN_BIT, mxic->regs + HC_EN);
 
-	ss_ctrl = OP_CMD_BYTES(1) | OP_CMD_BUSW(fls(op->cmd.buswidth) - 1);
-
-	if (op->addr.nbytes)
-		ss_ctrl |= OP_ADDR_BYTES(op->addr.nbytes) |
-			   OP_ADDR_BUSW(fls(op->addr.buswidth) - 1);
-
-	if (op->dummy.nbytes)
-		ss_ctrl |= OP_DUMMY_CYC(op->dummy.nbytes);
-
-	if (op->data.nbytes) {
-		ss_ctrl |= OP_DATA_BUSW(fls(op->data.buswidth) - 1);
-		if (op->data.dir == SPI_MEM_DATA_IN)
-			ss_ctrl |= OP_READ;
-	}
-
-	writel(ss_ctrl, mxic->regs + SS_CTRL(mem->spi->chip_select));
+	writel(mxic_spi_mem_prep_op_cfg(op),
+	       mxic->regs + SS_CTRL(mem->spi->chip_select));
 
 	writel(readl(mxic->regs + HC_CFG) | HC_CFG_MAN_CS_ASSERT,
 	       mxic->regs + HC_CFG);
 
-	ret = mxic_spi_data_xfer(mxic, &op->cmd.opcode, NULL, 1);
+	cmd[0] = op->cmd.opcode;
+	if (op->cmd.nbytes == 2)
+		cmd[1] = op->cmd.ext_opcode;
+
+	ret = mxic_spi_data_xfer(mxic, cmd, NULL, op->cmd.nbytes);
 	if (ret)
 		goto out;
 
@@ -566,7 +601,8 @@ static int mxic_spi_probe(struct platform_device *pdev)
 	master->bits_per_word_mask = SPI_BPW_MASK(8);
 	master->mode_bits = SPI_CPOL | SPI_CPHA |
 			SPI_RX_DUAL | SPI_TX_DUAL |
-			SPI_RX_QUAD | SPI_TX_QUAD;
+			SPI_RX_QUAD | SPI_TX_QUAD |
+			SPI_RX_OCTAL | SPI_TX_OCTAL;
 
 	mxic_spi_hw_init(mxic);
 
-- 
1.9.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

  parent reply	other threads:[~2019-11-15  8:59 UTC|newest]

Thread overview: 38+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-11-15  8:58 [PATCH 0/4] mtd: spi-nor: Add support for Octal 8D-8D-8D mode Mason Yang
2019-11-15  8:58 ` Mason Yang
2019-11-15  8:58 ` [PATCH 1/4] spi: spi-mem: " Mason Yang
2019-11-15  8:58   ` Mason Yang
2019-11-15  8:58 ` [PATCH 2/4] mtd: spi-nor: " Mason Yang
2019-11-15  8:58   ` Mason Yang
2019-11-15 12:30   ` kbuild test robot
2019-11-15 12:30     ` kbuild test robot
2019-11-15 12:30     ` kbuild test robot
2019-11-15 13:42   ` kbuild test robot
2019-11-15 13:42     ` kbuild test robot
2019-11-15 13:42     ` kbuild test robot
2019-12-04 12:46   ` Vignesh Raghavendra
2019-12-04 12:46     ` Vignesh Raghavendra
2019-12-09  7:56     ` masonccyang
2019-12-09  7:56       ` masonccyang
2019-12-09  9:53       ` Vignesh Raghavendra
2019-12-09  9:53         ` Vignesh Raghavendra
2019-12-10  7:21         ` masonccyang
2019-12-10  7:21           ` masonccyang
2019-11-15  8:58 ` [PATCH 3/4] mtd: spi-nor: Add Octal 8D-8D-8D mode support for Macronix mx25uw51245g Mason Yang
2019-11-15  8:58   ` Mason Yang
2019-12-04 13:03   ` Vignesh Raghavendra
2019-12-04 13:03     ` Vignesh Raghavendra
2019-12-09  6:38     ` masonccyang
2019-12-09  6:38       ` masonccyang
2019-11-15  8:58 ` Mason Yang [this message]
2019-11-15  8:58   ` [PATCH 4/4] spi: mxic: Add support for Octal 8D-8D-8D mode Mason Yang
2019-11-15 14:39   ` kbuild test robot
2019-11-15 14:39     ` kbuild test robot
2019-11-15 14:39     ` kbuild test robot
2019-11-16  7:20   ` kbuild test robot
2019-11-16  7:20     ` kbuild test robot
2019-11-16  7:20     ` kbuild test robot
2019-12-10 17:00 ` [PATCH 0/4] mtd: spi-nor: " Tudor.Ambarus
2019-12-10 17:00   ` Tudor.Ambarus
2019-12-11  2:14   ` masonccyang
2019-12-11  2:14     ` masonccyang

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1573808288-19365-5-git-send-email-masonccyang@mxic.com.tw \
    --to=masonccyang@mxic.com.tw \
    --cc=bbrezillon@kernel.org \
    --cc=broonie@kernel.org \
    --cc=computersforpeace@gmail.com \
    --cc=dwmw2@infradead.org \
    --cc=juliensu@mxic.com.tw \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=marek.vasut@gmail.com \
    --cc=miquel.raynal@bootlin.com \
    --cc=richard@nod.at \
    --cc=tudor.ambarus@microchip.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.