* [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver
@ 2020-09-18 9:10 Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 01/10] dt-binding: usb: add bindings for some common properties Chunfeng Yun
` (10 more replies)
0 siblings, 11 replies; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
These patches introduce the MediaTek USB3 Dual-Role Controller
driver.
The driver can be configured as Peripheral only and Host only(xHCI)
modes, and it's ported from Linux Kernel 5.8-rc1
v7 changes
1. use xhci quirk flag XHCI_MTK_HOST
v6 changes
1. modify commit message of [4/10]
v5 changes:
1. change condition of readl_poll_timeout() when check clocks
2. add xhci-mtk.c and myself as maintainer for MTK USB
v4 changes:
1. [4/10], [9/10] and [10/10] are new patches
2. add a glue driver
3. add host driver and rebuild host flow
4. support force_vbus mode for device
5. update bindings to support glue driver
v3 changes:
1. add patch [5/7]
2. add udc_set_speed()
3. simplify some code flow
v2 changes:
1. simplify QMU operations
Chunfeng Yun (10):
dt-binding: usb: add bindings for some common properties
dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD
usb: add USB_SPEED_SUPER_PLUS
usb: common: add define of usb_speed_string()
usb: add MediaTek USB3 DRD driver
usb: gadget: Add bcdDevice for the MTU3 USB Gadget Controller
arm: dts: mt8512: add usb related nodes
configs: mt8512: enable fastboot
configs: mt8512: add USB host related configs
MAINTAINERS: add USB driver to ARM MEDIATEK
MAINTAINERS | 3 +
Makefile | 1 +
arch/arm/dts/mt8512-bm1-emmc.dts | 34 +
arch/arm/dts/mt8512.dtsi | 49 +-
configs/mt8512_bm1_emmc_defconfig | 26 +
doc/device-tree-bindings/usb/generic.txt | 31 +
doc/device-tree-bindings/usb/mediatek,mtu3.txt | 79 +++
drivers/usb/Kconfig | 2 +
drivers/usb/common/common.c | 8 +
drivers/usb/gadget/gadget_chips.h | 8 +
drivers/usb/mtu3/Kconfig | 45 ++
drivers/usb/mtu3/Makefile | 11 +
drivers/usb/mtu3/mtu3.h | 423 +++++++++++
drivers/usb/mtu3/mtu3_core.c | 838 ++++++++++++++++++++++
drivers/usb/mtu3/mtu3_dr.h | 52 ++
drivers/usb/mtu3/mtu3_gadget.c | 686 ++++++++++++++++++
drivers/usb/mtu3/mtu3_gadget_ep0.c | 933 +++++++++++++++++++++++++
drivers/usb/mtu3/mtu3_host.c | 141 ++++
drivers/usb/mtu3/mtu3_hw_regs.h | 515 ++++++++++++++
drivers/usb/mtu3/mtu3_plat.c | 368 ++++++++++
drivers/usb/mtu3/mtu3_qmu.c | 504 +++++++++++++
drivers/usb/mtu3/mtu3_qmu.h | 37 +
include/linux/usb/ch9.h | 5 +-
23 files changed, 4794 insertions(+), 5 deletions(-)
create mode 100644 doc/device-tree-bindings/usb/generic.txt
create mode 100644 doc/device-tree-bindings/usb/mediatek,mtu3.txt
create mode 100644 drivers/usb/mtu3/Kconfig
create mode 100644 drivers/usb/mtu3/Makefile
create mode 100644 drivers/usb/mtu3/mtu3.h
create mode 100644 drivers/usb/mtu3/mtu3_core.c
create mode 100644 drivers/usb/mtu3/mtu3_dr.h
create mode 100644 drivers/usb/mtu3/mtu3_gadget.c
create mode 100644 drivers/usb/mtu3/mtu3_gadget_ep0.c
create mode 100644 drivers/usb/mtu3/mtu3_host.c
create mode 100644 drivers/usb/mtu3/mtu3_hw_regs.h
create mode 100644 drivers/usb/mtu3/mtu3_plat.c
create mode 100644 drivers/usb/mtu3/mtu3_qmu.c
create mode 100644 drivers/usb/mtu3/mtu3_qmu.h
--
1.9.1
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 01/10] dt-binding: usb: add bindings for some common properties
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
@ 2020-09-18 9:10 ` Chunfeng Yun
2020-10-13 14:15 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 02/10] dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD Chunfeng Yun
` (9 subsequent siblings)
10 siblings, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
Add bindings for common properties, include maximum-speed,
dr_mode and phy_type
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2~v7: no changes
---
doc/device-tree-bindings/usb/generic.txt | 31 +++++++++++++++++++++++++++++++
1 file changed, 31 insertions(+)
create mode 100644 doc/device-tree-bindings/usb/generic.txt
diff --git a/doc/device-tree-bindings/usb/generic.txt b/doc/device-tree-bindings/usb/generic.txt
new file mode 100644
index 0000000..a02a198
--- /dev/null
+++ b/doc/device-tree-bindings/usb/generic.txt
@@ -0,0 +1,31 @@
+Generic USB Properties
+
+Optional properties:
+ - maximum-speed: tells USB controllers we want to work up to a certain
+ speed. Valid arguments are "super-speed-plus",
+ "super-speed", "high-speed", "full-speed" and
+ "low-speed". In case this isn't passed via DT, USB
+ controllers should default to their maximum HW
+ capability.
+ - dr_mode: tells Dual-Role USB controllers that we want to work on a
+ particular mode. Valid arguments are "host",
+ "peripheral" and "otg". In case this attribute isn't
+ passed via DT, USB DRD controllers should default to
+ OTG.
+ - phy_type: tells USB controllers that we want to configure the core to support
+ a UTMI+ PHY with an 8- or 16-bit interface if UTMI+ is
+ selected. Valid arguments are "utmi" and "utmi_wide".
+ In case this isn't passed via DT, USB controllers should
+ default to HW capability.
+
+This is an attribute to a USB controller such as:
+
+dwc3 at 4a030000 {
+ compatible = "synopsys,dwc3";
+ reg = <0x4a030000 0xcfff>;
+ interrupts = <0 92 4>
+ usb-phy = <&usb2_phy>, <&usb3,phy>;
+ maximum-speed = "super-speed";
+ dr_mode = "otg";
+ phy_type = "utmi_wide";
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [PATCH next v7 02/10] dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 01/10] dt-binding: usb: add bindings for some common properties Chunfeng Yun
@ 2020-09-18 9:10 ` Chunfeng Yun
2020-10-13 14:18 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 03/10] usb: add USB_SPEED_SUPER_PLUS Chunfeng Yun
` (8 subsequent siblings)
10 siblings, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
Add dt-binding for MediaTek USB3 DRD Driver
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v5~v7: no changes
v4:
Add support host mode, introduce some new properties and subnode
v2~v3: no changes
---
doc/device-tree-bindings/usb/mediatek,mtu3.txt | 79 ++++++++++++++++++++++++++
1 file changed, 79 insertions(+)
create mode 100644 doc/device-tree-bindings/usb/mediatek,mtu3.txt
diff --git a/doc/device-tree-bindings/usb/mediatek,mtu3.txt b/doc/device-tree-bindings/usb/mediatek,mtu3.txt
new file mode 100644
index 0000000..ab877bf
--- /dev/null
+++ b/doc/device-tree-bindings/usb/mediatek,mtu3.txt
@@ -0,0 +1,79 @@
+The device node for Mediatek USB3 DRD controller
+
+Required properties:
+ - compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3",
+ soc-model is the name of SoC, such as mt8512 etc,
+ when using "mediatek,mtu3" compatible string, you need SoC specific
+ ones in addition, one of:
+ - "mediatek,mt8512-mtu3"
+ - reg : specifies physical base address and size of the registers
+ - reg-names: should be
+ - "ippc" : IP Port Control
+ - power-domains : a phandle to USB power domain node to control USB's MTCMOS
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+ - clock-names : must contain "sys_ck" for clock of controller,
+ the following clocks are optional:
+ "ref_ck", "mcu_ck", "dma_ck" and "xhci_ck";
+ - phys : list of all the USB PHYs on this HCD
+ - #address-cells, #size-cells : used for sub-nodes with 'reg' property
+ - ranges : allows valid 1:1 translation between child's address space and
+ parent's address space
+
+Optional properties:
+ - vusb33-supply : regulator of USB AVDD3.3v
+ - vbus-supply : regulator of VBUS 5v, needed when supports host mode.
+
+Sub-nodes:
+Required properties:
+ - compatible : should be "mediatek,ssusb"
+ - reg : specifies physical base address and size of the registers
+ - reg-names: should be
+ - "mac" : SSUSB MAC, include xHCI and device
+ - interrupts : interrupt used by xHCI or device
+ - dr_mode : should be one of "host" or "peripheral",
+ see : usb/generic.txt
+
+Optional properties:
+ - pinctrl-names : a pinctrl state named "default" is optional
+ - pinctrl-0 : pin control group
+ See: pinctrl/pinctrl-bindings.txt
+
+ - device mode:
+ - maximum-speed : valid arguments are "full-speed", "high-speed",
+ "super-speed" and "super-speed-plus",
+ see: usb/generic.txt
+ - mediatek,force-vbus : force vbus as valid by SW
+
+ - host mode (dr_mode is "host"):
+ - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0,
+ bit1 for u3port1, ... etc;
+
+Example:
+usb3: usb at 11213e00 {
+ compatible = "mediatek,mt8512-mtu3", "mediatek,mtu3";
+ reg = <0x11213e00 0x0100>;
+ reg-names = "ippc";
+ phys = <&u2port0 PHY_TYPE_USB2>, <&u2port1 PHY_TYPE_USB2>;
+ power-domains = <&scpsys MT8512_POWER_DOMAIN_USB>;
+ clocks = <&infracfg CLK_INFRA_USB_SYS>,
+ <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+ <&infracfg CLK_INFRA_ICUSB>;
+ clock-names = "sys_ck", "ref_ck", "mcu_ck";
+ vusb33-supply = <reg_3p3v>;
+ vbus-supply = <&usb_p0_vbus>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ ssusb: usb at 11210000 {
+ compatible = "mediatek,ssusb";
+ reg = <0x11210000 0x3e00>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
+ reg-names = "mac";
+ dr_mode = "peripheral";
+ maximum-speed = "high-speed";
+ status = "disabled";
+ };
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [PATCH next v7 03/10] usb: add USB_SPEED_SUPER_PLUS
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 01/10] dt-binding: usb: add bindings for some common properties Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 02/10] dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD Chunfeng Yun
@ 2020-09-18 9:10 ` Chunfeng Yun
2020-10-13 14:19 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 04/10] usb: common: add define of usb_speed_string() Chunfeng Yun
` (7 subsequent siblings)
10 siblings, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
Add enum USB_SPEED_SUPER_PLUS for USB3.1
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v5~v7: no changes
v4: also add it into speed_names array
v2~v3: no changes
---
drivers/usb/common/common.c | 1 +
include/linux/usb/ch9.h | 1 +
2 files changed, 2 insertions(+)
diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
index d4ae186..76f5a9c 100644
--- a/drivers/usb/common/common.c
+++ b/drivers/usb/common/common.c
@@ -46,6 +46,7 @@ static const char *const speed_names[] = {
[USB_SPEED_HIGH] = "high-speed",
[USB_SPEED_WIRELESS] = "wireless",
[USB_SPEED_SUPER] = "super-speed",
+ [USB_SPEED_SUPER_PLUS] = "super-speed-plus",
};
enum usb_device_speed usb_get_maximum_speed(ofnode node)
diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
index 989a5fc..7d225ee 100644
--- a/include/linux/usb/ch9.h
+++ b/include/linux/usb/ch9.h
@@ -956,6 +956,7 @@ enum usb_device_speed {
USB_SPEED_HIGH, /* usb 2.0 */
USB_SPEED_WIRELESS, /* wireless (usb 2.5) */
USB_SPEED_SUPER, /* usb 3.0 */
+ USB_SPEED_SUPER_PLUS, /* usb 3.1 */
};
#ifdef __KERNEL__
--
1.9.1
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [PATCH next v7 04/10] usb: common: add define of usb_speed_string()
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
` (2 preceding siblings ...)
2020-09-18 9:10 ` [PATCH next v7 03/10] usb: add USB_SPEED_SUPER_PLUS Chunfeng Yun
@ 2020-09-18 9:10 ` Chunfeng Yun
2020-10-13 14:21 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 05/10] usb: add MediaTek USB3 DRD driver Chunfeng Yun
` (6 subsequent siblings)
10 siblings, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
There is only declaration of usb_speed_string(), but no definition,
so add it to avoid build error when call it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v7: no changes
v6: modify commit message suggested by Roger
v5: no changes
v4: new patch
---
drivers/usb/common/common.c | 7 +++++++
include/linux/usb/ch9.h | 4 ----
2 files changed, 7 insertions(+), 4 deletions(-)
diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
index 76f5a9c..5e5c3c3 100644
--- a/drivers/usb/common/common.c
+++ b/drivers/usb/common/common.c
@@ -49,6 +49,13 @@ static const char *const speed_names[] = {
[USB_SPEED_SUPER_PLUS] = "super-speed-plus",
};
+const char *usb_speed_string(enum usb_device_speed speed)
+{
+ if (speed < 0 || speed >= ARRAY_SIZE(speed_names))
+ speed = USB_SPEED_UNKNOWN;
+ return speed_names[speed];
+}
+
enum usb_device_speed usb_get_maximum_speed(ofnode node)
{
const char *max_speed;
diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
index 7d225ee..a8fa5d7 100644
--- a/include/linux/usb/ch9.h
+++ b/include/linux/usb/ch9.h
@@ -959,8 +959,6 @@ enum usb_device_speed {
USB_SPEED_SUPER_PLUS, /* usb 3.1 */
};
-#ifdef __KERNEL__
-
/**
* usb_speed_string() - Returns human readable-name of the speed.
* @speed: The speed to return human-readable name for. If it's not
@@ -969,8 +967,6 @@ enum usb_device_speed {
*/
extern const char *usb_speed_string(enum usb_device_speed speed);
-#endif
-
enum usb_device_state {
/* NOTATTACHED isn't in the USB spec, and this state acts
* the same as ATTACHED ... but it's clearer this way.
--
1.9.1
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [PATCH next v7 05/10] usb: add MediaTek USB3 DRD driver
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
` (3 preceding siblings ...)
2020-09-18 9:10 ` [PATCH next v7 04/10] usb: common: add define of usb_speed_string() Chunfeng Yun
@ 2020-09-18 9:10 ` Chunfeng Yun
2020-10-13 14:26 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 06/10] usb: gadget: Add bcdDevice for the MTU3 USB Gadget Controller Chunfeng Yun
` (5 subsequent siblings)
10 siblings, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
This patch adds support for the MediaTek USB3 DRD controller,
its host side is based on xHCI, this driver supports device mode
and host mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v7:
1. use xhci quirk flag XHCI_MTK_HOST
v6: no changes
v5:
1. change condition of readl_poll_timeout() when check clocks
v4:
1. remove unused member @busy and @wedged, use their flags instead
2. support force_vbus mode
3. add a glue driver using UCLASS_NOP
4. add host driver, and rebuild host flow
v3 changes
1. add ->udc_set_speed()
2. simplify some code flow
v2: simplify QMU operations
---
Makefile | 1 +
drivers/usb/Kconfig | 2 +
drivers/usb/mtu3/Kconfig | 45 ++
drivers/usb/mtu3/Makefile | 11 +
drivers/usb/mtu3/mtu3.h | 423 +++++++++++++++++
drivers/usb/mtu3/mtu3_core.c | 838 +++++++++++++++++++++++++++++++++
drivers/usb/mtu3/mtu3_dr.h | 52 +++
drivers/usb/mtu3/mtu3_gadget.c | 686 +++++++++++++++++++++++++++
drivers/usb/mtu3/mtu3_gadget_ep0.c | 933 +++++++++++++++++++++++++++++++++++++
drivers/usb/mtu3/mtu3_host.c | 141 ++++++
drivers/usb/mtu3/mtu3_hw_regs.h | 515 ++++++++++++++++++++
drivers/usb/mtu3/mtu3_plat.c | 368 +++++++++++++++
drivers/usb/mtu3/mtu3_qmu.c | 504 ++++++++++++++++++++
drivers/usb/mtu3/mtu3_qmu.h | 37 ++
14 files changed, 4556 insertions(+)
create mode 100644 drivers/usb/mtu3/Kconfig
create mode 100644 drivers/usb/mtu3/Makefile
create mode 100644 drivers/usb/mtu3/mtu3.h
create mode 100644 drivers/usb/mtu3/mtu3_core.c
create mode 100644 drivers/usb/mtu3/mtu3_dr.h
create mode 100644 drivers/usb/mtu3/mtu3_gadget.c
create mode 100644 drivers/usb/mtu3/mtu3_gadget_ep0.c
create mode 100644 drivers/usb/mtu3/mtu3_host.c
create mode 100644 drivers/usb/mtu3/mtu3_hw_regs.h
create mode 100644 drivers/usb/mtu3/mtu3_plat.c
create mode 100644 drivers/usb/mtu3/mtu3_qmu.c
create mode 100644 drivers/usb/mtu3/mtu3_qmu.h
diff --git a/Makefile b/Makefile
index 7a05fc7..2dcc41a 100644
--- a/Makefile
+++ b/Makefile
@@ -795,6 +795,7 @@ libs-y += drivers/usb/eth/
libs-$(CONFIG_USB_GADGET) += drivers/usb/gadget/
libs-$(CONFIG_USB_GADGET) += drivers/usb/gadget/udc/
libs-y += drivers/usb/host/
+libs-y += drivers/usb/mtu3/
libs-y += drivers/usb/musb/
libs-y += drivers/usb/musb-new/
libs-y += drivers/usb/phy/
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index 34881a1..fedc013 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -72,6 +72,8 @@ source "drivers/usb/cdns3/Kconfig"
source "drivers/usb/dwc3/Kconfig"
+source "drivers/usb/mtu3/Kconfig"
+
source "drivers/usb/musb/Kconfig"
source "drivers/usb/musb-new/Kconfig"
diff --git a/drivers/usb/mtu3/Kconfig b/drivers/usb/mtu3/Kconfig
new file mode 100644
index 0000000..66651ad
--- /dev/null
+++ b/drivers/usb/mtu3/Kconfig
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# For MTK USB3.0 IP
+
+config USB_MTU3
+ bool "MediaTek USB3 Dual Role controller"
+ depends on USB || USB_GADGET
+ depends on ARCH_MEDIATEK
+ help
+ Say Y here if your system runs on MediaTek SoCs with
+ Dual Role SuperSpeed USB controller. You can select usb
+ mode as peripheral role or host role.
+
+ If you don't know what this is, please say N.
+
+if USB_MTU3
+choice
+ bool "MTU3 Mode Selection"
+ default USB_MTU3_GADGET if USB_GADGET
+ default USB_MTU3_HOST if (USB && !USB_GADGET)
+
+config USB_MTU3_HOST
+ bool "Host only mode"
+ depends on USB=y || USB=USB_MTU3
+ select USB_XHCI_HCD
+ help
+ Select this when you want to use MTU3 in host mode only,
+ thereby the gadget feature will be regressed.
+
+config USB_MTU3_GADGET
+ bool "Gadget only mode"
+ depends on USB_GADGET=y || USB_GADGET=USB_MTU3
+ select USB_GADGET_DUALSPEED
+ help
+ Select this when you want to use MTU3 in gadget mode only,
+ thereby the host feature will be regressed.
+
+endchoice
+
+config USB_MTU3_DEBUG
+ bool "Enable Debugging Messages"
+ help
+ Say Y here to enable debugging messages in the MTU3 Driver.
+
+endif
diff --git a/drivers/usb/mtu3/Makefile b/drivers/usb/mtu3/Makefile
new file mode 100644
index 0000000..234f3a3
--- /dev/null
+++ b/drivers/usb/mtu3/Makefile
@@ -0,0 +1,11 @@
+# SPDX-License-Identifier: GPL-2.0
+
+ccflags-$(CONFIG_USB_MTU3_DEBUG) += -DDEBUG
+
+obj-$(CONFIG_USB_MTU3) += mtu3.o
+
+mtu3-y := mtu3_plat.o
+
+obj-$(CONFIG_USB_MTU3_GADGET) += mtu3_core.o mtu3_gadget_ep0.o mtu3_gadget.o
+obj-$(CONFIG_USB_MTU3_GADGET) += mtu3_qmu.o
+obj-$(CONFIG_USB_MTU3_HOST) += mtu3_host.o
diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h
new file mode 100644
index 0000000..7ff8ea8
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3.h
@@ -0,0 +1,423 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * mtu3.h - MediaTek USB3 DRD header
+ *
+ * Copyright (C) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+#ifndef __MTU3_H__
+#define __MTU3_H__
+
+#include <asm/io.h>
+#include <clk.h>
+#include <dm.h>
+#include <dm/devres.h>
+#include <generic-phy.h>
+#include <linux/bug.h>
+#include <linux/delay.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/otg.h>
+#include <power/regulator.h>
+#include <usb/xhci.h>
+
+struct mtu3;
+struct mtu3_ep;
+struct mtu3_request;
+struct mtu3_host;
+
+#include "mtu3_hw_regs.h"
+#include "mtu3_qmu.h"
+
+#define MU3D_EP_TXCR0(epnum) (U3D_TX1CSR0 + (((epnum) - 1) * 0x10))
+#define MU3D_EP_TXCR1(epnum) (U3D_TX1CSR1 + (((epnum) - 1) * 0x10))
+#define MU3D_EP_TXCR2(epnum) (U3D_TX1CSR2 + (((epnum) - 1) * 0x10))
+
+#define MU3D_EP_RXCR0(epnum) (U3D_RX1CSR0 + (((epnum) - 1) * 0x10))
+#define MU3D_EP_RXCR1(epnum) (U3D_RX1CSR1 + (((epnum) - 1) * 0x10))
+#define MU3D_EP_RXCR2(epnum) (U3D_RX1CSR2 + (((epnum) - 1) * 0x10))
+
+#define USB_QMU_RQCSR(epnum) (U3D_RXQCSR1 + (((epnum) - 1) * 0x10))
+#define USB_QMU_RQSAR(epnum) (U3D_RXQSAR1 + (((epnum) - 1) * 0x10))
+#define USB_QMU_RQCPR(epnum) (U3D_RXQCPR1 + (((epnum) - 1) * 0x10))
+
+#define USB_QMU_TQCSR(epnum) (U3D_TXQCSR1 + (((epnum) - 1) * 0x10))
+#define USB_QMU_TQSAR(epnum) (U3D_TXQSAR1 + (((epnum) - 1) * 0x10))
+#define USB_QMU_TQCPR(epnum) (U3D_TXQCPR1 + (((epnum) - 1) * 0x10))
+
+#define SSUSB_U3_CTRL(p) (U3D_SSUSB_U3_CTRL_0P + ((p) * 0x08))
+#define SSUSB_U2_CTRL(p) (U3D_SSUSB_U2_CTRL_0P + ((p) * 0x08))
+
+#define MTU3_DRIVER_NAME "mtu3-gadget"
+#define DMA_ADDR_INVALID (~(dma_addr_t)0)
+
+#define MTU3_EP_ENABLED BIT(0)
+#define MTU3_EP_STALL BIT(1)
+#define MTU3_EP_WEDGE BIT(2)
+#define MTU3_EP_BUSY BIT(3)
+
+/* should be set as 1 */
+#define MTU3_U2_IP_SLOT_DEFAULT 1
+#define MTU3_U3_IP_SLOT_DEFAULT (MTU3_U2_IP_SLOT_DEFAULT)
+
+/**
+ * IP TRUNK version
+ * from 0x1003 version, USB3 Gen2 is supported, two changes affect driver:
+ * 1. MAXPKT and MULTI bits layout of TXCSR1 and RXCSR1 are adjusted,
+ * but not backward compatible
+ * 2. QMU extend buffer length supported
+ */
+#define MTU3_TRUNK_VERS_1003 0x1003
+
+/**
+ * Normally the device works on HS or SS, to simplify fifo management,
+ * devide fifo into some 2*maxp parts, use bitmap to manage it; And
+ * 32 bits size of bitmap is large enough, that means it can manage
+ * up to 32KB/64KB fifo size.
+ * NOTE: MTU3_U2/3IP_EP_FIFO_UNIT should be power of two;
+ * FIFO size is allocated according to @slot which is 1 by default
+ */
+#define USB_HS_MAXP 512
+#define USB_SS_MAXP 1024
+#define MTU3_U2IP_EP_FIFO_UNIT \
+ ((USB_HS_MAXP) * ((MTU3_U2_IP_SLOT_DEFAULT) + 1))
+#define MTU3_U3IP_EP_FIFO_UNIT \
+ ((USB_SS_MAXP) * ((MTU3_U3_IP_SLOT_DEFAULT) + 1))
+
+#define MTU3_FIFO_BIT_SIZE 32
+#define MTU3_U2_IP_EP0_FIFO_SIZE 64
+
+/**
+ * Maximum size of ep0 response buffer for ch9 requests,
+ * the SET_SEL request uses 6 so far, and GET_STATUS is 2
+ */
+#define EP0_RESPONSE_BUF 6
+
+/* device operated link and speed got from DEVICE_CONF register */
+enum mtu3_speed {
+ MTU3_SPEED_INACTIVE = 0,
+ MTU3_SPEED_FULL = 1,
+ MTU3_SPEED_HIGH = 3,
+ MTU3_SPEED_SUPER = 4,
+ MTU3_SPEED_SUPER_PLUS = 5,
+};
+
+/**
+ * @MU3D_EP0_STATE_SETUP: waits for SETUP or received a SETUP
+ * without data stage.
+ * @MU3D_EP0_STATE_TX: IN data stage
+ * @MU3D_EP0_STATE_RX: OUT data stage
+ * @MU3D_EP0_STATE_TX_END: the last IN data is transferred, and
+ * waits for its completion interrupt
+ * @MU3D_EP0_STATE_STALL: ep0 is in stall status, will be auto-cleared
+ * after receives a SETUP.
+ */
+enum mtu3_g_ep0_state {
+ MU3D_EP0_STATE_SETUP = 1,
+ MU3D_EP0_STATE_TX,
+ MU3D_EP0_STATE_RX,
+ MU3D_EP0_STATE_TX_END,
+ MU3D_EP0_STATE_STALL,
+};
+
+/**
+ * MTU3_DR_FORCE_NONE: automatically switch host and peripheral mode
+ * by IDPIN signal.
+ * MTU3_DR_FORCE_HOST: force to enter host mode and override OTG
+ * IDPIN signal.
+ * MTU3_DR_FORCE_DEVICE: force to enter peripheral mode.
+ */
+enum mtu3_dr_force_mode {
+ MTU3_DR_FORCE_NONE = 0,
+ MTU3_DR_FORCE_HOST,
+ MTU3_DR_FORCE_DEVICE,
+};
+
+/**
+ * @mac_base: register base address of MAC, include xHCI and device
+ * @ippc_base: register base address of IP Power and Clock interface (IPPC)
+ * @vusb33_supply: usb3.3V shared by device/host IP
+ * @vbus_supply: vbus 5v of OTG port
+ * @clks: optional clocks, include "sys_ck", "ref_ck", "mcu_ck",
+ * "dma_ck" and "xhci_ck"
+ * @phys: phys used
+ * @dr_mode: works in which mode:
+ * host only, device only or dual-role mode
+ */
+struct ssusb_mtk {
+ struct udevice *dev;
+ struct mtu3 *u3d;
+ struct mtu3_host *u3h;
+ void __iomem *mac_base;
+ void __iomem *ippc_base;
+ /* common power & clock */
+ struct udevice *vusb33_supply;
+ struct udevice *vbus_supply;
+ struct clk_bulk clks;
+ struct phy_bulk phys;
+ /* otg */
+ enum usb_dr_mode dr_mode;
+};
+
+/**
+ * @ctrl: xHCI controller, needs to come first in this struct!
+ * @hcd: xHCI's register base address
+ * @u2_ports: number of usb2 host ports
+ * @u3_ports: number of usb3 host ports
+ * @u3p_dis_msk: mask of disabling usb3 ports, for example, bit0==1 to
+ * disable u3port0, bit1==1 to disable u3port1,... etc
+ */
+struct mtu3_host {
+ struct xhci_ctrl ctrl;
+ struct xhci_hccr *hcd;
+ void __iomem *ippc_base;
+ struct ssusb_mtk *ssusb;
+ struct udevice *dev;
+ u32 u2_ports;
+ u32 u3_ports;
+ u32 u3p_dis_msk;
+};
+
+/**
+ * @base: the base address of fifo
+ * @limit: the bitmap size in bits
+ * @bitmap: fifo bitmap in unit of @MTU3_EP_FIFO_UNIT
+ */
+struct mtu3_fifo_info {
+ u32 base;
+ u32 limit;
+ DECLARE_BITMAP(bitmap, MTU3_FIFO_BIT_SIZE);
+};
+
+/**
+ * General Purpose Descriptor (GPD):
+ * The format of TX GPD is a little different from RX one.
+ * And the size of GPD is 16 bytes.
+ *
+ * @flag:
+ * bit0: Hardware Own (HWO)
+ * bit1: Buffer Descriptor Present (BDP), always 0, BD is not supported
+ * bit2: Bypass (BPS), 1: HW skips this GPD if HWO = 1
+ * bit7: Interrupt On Completion (IOC)
+ * @chksum: This is used to validate the contents of this GPD;
+ * If TXQ_CS_EN / RXQ_CS_EN bit is set, an interrupt is issued
+ * when checksum validation fails;
+ * Checksum value is calculated over the 16 bytes of the GPD by default;
+ * @data_buf_len (RX ONLY): This value indicates the length of
+ * the assigned data buffer
+ * @next_gpd: Physical address of the next GPD
+ * @buffer: Physical address of the data buffer
+ * @buf_len:
+ * (TX): This value indicates the length of the assigned data buffer
+ * (RX): The total length of data received
+ * @ext_len: reserved
+ * @ext_flag:
+ * bit5 (TX ONLY): Zero Length Packet (ZLP),
+ */
+struct qmu_gpd {
+ __u8 flag;
+ __u8 chksum;
+ __le16 data_buf_len;
+ __le32 next_gpd;
+ __le32 buffer;
+ __le16 buf_len;
+ __u8 ext_len;
+ __u8 ext_flag;
+} __packed;
+
+/**
+ * dma: physical base address of GPD segment
+ * start: virtual base address of GPD segment
+ * end: the last GPD element
+ * enqueue: the first empty GPD to use
+ * dequeue: the first completed GPD serviced by ISR
+ * NOTE: the size of GPD ring should be >= 2
+ */
+struct mtu3_gpd_ring {
+ dma_addr_t dma;
+ struct qmu_gpd *start;
+ struct qmu_gpd *end;
+ struct qmu_gpd *enqueue;
+ struct qmu_gpd *dequeue;
+};
+
+/**
+ * @fifo_size: it is (@slot + 1) * @fifo_seg_size
+ * @fifo_seg_size: it is roundup_pow_of_two(@maxp)
+ */
+struct mtu3_ep {
+ struct usb_ep ep;
+ char name[12];
+ struct mtu3 *mtu;
+ u8 epnum;
+ u8 type;
+ u8 is_in;
+ u16 maxp;
+ int slot;
+ u32 fifo_size;
+ u32 fifo_addr;
+ u32 fifo_seg_size;
+ struct mtu3_fifo_info *fifo;
+
+ struct list_head req_list;
+ struct mtu3_gpd_ring gpd_ring;
+ const struct usb_ss_ep_comp_descriptor *comp_desc;
+ const struct usb_endpoint_descriptor *desc;
+
+ int flags;
+};
+
+struct mtu3_request {
+ struct usb_request request;
+ struct list_head list;
+ struct mtu3_ep *mep;
+ struct mtu3 *mtu;
+ struct qmu_gpd *gpd;
+ int epnum;
+};
+
+static inline struct ssusb_mtk *dev_to_ssusb(struct udevice *dev)
+{
+ return dev_get_priv(dev);
+}
+
+/**
+ * struct mtu3 - device driver instance data.
+ * @slot: MTU3_U2_IP_SLOT_DEFAULT for U2 IP only,
+ * MTU3_U3_IP_SLOT_DEFAULT for U3 IP
+ * @may_wakeup: means device's remote wakeup is enabled
+ * @is_self_powered: is reported in device status and the config descriptor
+ * @delayed_status: true when function drivers ask for delayed status
+ * @gen2cp: compatible with USB3 Gen2 IP
+ * @ep0_req: dummy request used while handling standard USB requests
+ * for GET_STATUS and SET_SEL
+ * @setup_buf: ep0 response buffer for GET_STATUS and SET_SEL requests
+ */
+struct mtu3 {
+ spinlock_t lock;
+ struct ssusb_mtk *ssusb;
+ struct udevice *dev;
+ void __iomem *mac_base;
+ void __iomem *ippc_base;
+ int irq;
+
+ struct mtu3_fifo_info tx_fifo;
+ struct mtu3_fifo_info rx_fifo;
+
+ struct mtu3_ep *ep_array;
+ struct mtu3_ep *in_eps;
+ struct mtu3_ep *out_eps;
+ struct mtu3_ep *ep0;
+ int num_eps;
+ int slot;
+ int active_ep;
+
+ enum mtu3_g_ep0_state ep0_state;
+ struct usb_gadget g; /* the gadget */
+ struct usb_gadget_driver *gadget_driver;
+ struct mtu3_request ep0_req;
+ u8 setup_buf[EP0_RESPONSE_BUF];
+ enum usb_device_speed max_speed;
+ enum usb_device_speed speed;
+
+ unsigned is_active:1;
+ unsigned may_wakeup:1;
+ unsigned is_self_powered:1;
+ unsigned test_mode:1;
+ unsigned softconnect:1;
+ unsigned u1_enable:1;
+ unsigned u2_enable:1;
+ unsigned is_u3_ip:1;
+ unsigned delayed_status:1;
+ unsigned gen2cp:1;
+ unsigned force_vbus:1;
+
+ u8 address;
+ u8 test_mode_nr;
+ u32 hw_version;
+};
+
+static inline struct mtu3 *gadget_to_mtu3(struct usb_gadget *g)
+{
+ return container_of(g, struct mtu3, g);
+}
+
+static inline int is_first_entry(const struct list_head *list,
+ const struct list_head *head)
+{
+ return list_is_last(head, list);
+}
+
+static inline struct mtu3_request *to_mtu3_request(struct usb_request *req)
+{
+ return req ? container_of(req, struct mtu3_request, request) : NULL;
+}
+
+static inline struct mtu3_ep *to_mtu3_ep(struct usb_ep *ep)
+{
+ return ep ? container_of(ep, struct mtu3_ep, ep) : NULL;
+}
+
+static inline struct mtu3_request *next_request(struct mtu3_ep *mep)
+{
+ if (list_empty(&mep->req_list))
+ return NULL;
+
+ return list_first_entry(&mep->req_list, struct mtu3_request, list);
+}
+
+static inline void mtu3_writel(void __iomem *base, u32 offset, u32 data)
+{
+ writel(data, base + offset);
+}
+
+static inline u32 mtu3_readl(void __iomem *base, u32 offset)
+{
+ return readl(base + offset);
+}
+
+static inline void mtu3_setbits(void __iomem *base, u32 offset, u32 bits)
+{
+ void __iomem *addr = base + offset;
+ u32 tmp = readl(addr);
+
+ writel((tmp | (bits)), addr);
+}
+
+static inline void mtu3_clrbits(void __iomem *base, u32 offset, u32 bits)
+{
+ void __iomem *addr = base + offset;
+ u32 tmp = readl(addr);
+
+ writel((tmp & ~(bits)), addr);
+}
+
+int ssusb_check_clocks(struct ssusb_mtk *ssusb, u32 ex_clks);
+struct usb_request *mtu3_alloc_request(struct usb_ep *ep, gfp_t gfp_flags);
+void mtu3_free_request(struct usb_ep *ep, struct usb_request *req);
+void mtu3_req_complete(struct mtu3_ep *mep,
+ struct usb_request *req, int status);
+
+int mtu3_config_ep(struct mtu3 *mtu, struct mtu3_ep *mep,
+ int interval, int burst, int mult);
+void mtu3_deconfig_ep(struct mtu3 *mtu, struct mtu3_ep *mep);
+void mtu3_ep_stall_set(struct mtu3_ep *mep, bool set);
+void mtu3_ep0_setup(struct mtu3 *mtu);
+void mtu3_start(struct mtu3 *mtu);
+void mtu3_stop(struct mtu3 *mtu);
+void mtu3_dev_on_off(struct mtu3 *mtu, int is_on);
+void mtu3_set_speed(struct mtu3 *mtu, enum usb_device_speed speed);
+
+int mtu3_gadget_setup(struct mtu3 *mtu);
+void mtu3_gadget_cleanup(struct mtu3 *mtu);
+void mtu3_gadget_reset(struct mtu3 *mtu);
+void mtu3_gadget_suspend(struct mtu3 *mtu);
+void mtu3_gadget_resume(struct mtu3 *mtu);
+void mtu3_gadget_disconnect(struct mtu3 *mtu);
+
+irqreturn_t mtu3_ep0_isr(struct mtu3 *mtu);
+extern const struct usb_ep_ops mtu3_ep0_ops;
+
+#endif
diff --git a/drivers/usb/mtu3/mtu3_core.c b/drivers/usb/mtu3/mtu3_core.c
new file mode 100644
index 0000000..28136f8
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3_core.c
@@ -0,0 +1,838 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * mtu3_core.c - hardware access layer and gadget init/exit of
+ * MediaTek usb3 Dual-Role Controller Driver
+ *
+ * Copyright (C) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+#include <linux/log2.h>
+#include <linux/bitmap.h>
+
+#include "mtu3.h"
+#include "mtu3_dr.h"
+
+static int ep_fifo_alloc(struct mtu3_ep *mep, u32 seg_size)
+{
+ struct mtu3_fifo_info *fifo = mep->fifo;
+ struct mtu3 *mtu = mep->mtu;
+ u32 fz_bit;
+
+ mep->fifo_seg_size = mtu->is_u3_ip ? USB_SS_MAXP : USB_HS_MAXP;
+
+ fz_bit = find_first_zero_bit(fifo->bitmap, fifo->limit);
+ if (fz_bit >= fifo->limit)
+ return -EOVERFLOW;
+
+ mep->fifo_size = mep->fifo_seg_size * (mep->slot + 1);
+ mep->fifo_addr = fifo->base + mep->fifo_size * fz_bit;
+ generic_set_bit(fz_bit, fifo->bitmap);
+
+ dev_dbg(mep->mtu->dev, "%s fifo:%#x/%#x, bit: %d\n",
+ __func__, mep->fifo_seg_size, mep->fifo_size, fz_bit);
+
+ return mep->fifo_addr;
+}
+
+static void ep_fifo_free(struct mtu3_ep *mep)
+{
+ struct mtu3_fifo_info *fifo = mep->fifo;
+ u32 addr = mep->fifo_addr;
+ u32 bit;
+
+ if (unlikely(addr < fifo->base))
+ return;
+
+ bit = (addr - fifo->base) / mep->fifo_size;
+ generic_clear_bit(bit, fifo->bitmap);
+ mep->fifo_size = 0;
+ mep->fifo_seg_size = 0;
+
+ dev_dbg(mep->mtu->dev, "%s size:%#x/%#x, bit: %d\n",
+ __func__, mep->fifo_seg_size, mep->fifo_size, bit);
+}
+
+/* enable/disable U3D SS function */
+static inline void mtu3_ss_func_set(struct mtu3 *mtu, bool enable)
+{
+ /* If usb3_en==0, LTSSM will go to SS.Disable state */
+ if (enable)
+ mtu3_setbits(mtu->mac_base, U3D_USB3_CONFIG, USB3_EN);
+ else
+ mtu3_clrbits(mtu->mac_base, U3D_USB3_CONFIG, USB3_EN);
+
+ dev_dbg(mtu->dev, "USB3_EN = %d\n", !!enable);
+}
+
+/* set/clear U3D HS device soft connect */
+static inline void mtu3_hs_softconn_set(struct mtu3 *mtu, bool enable)
+{
+ if (enable) {
+ mtu3_setbits(mtu->mac_base, U3D_POWER_MANAGEMENT,
+ SOFT_CONN | SUSPENDM_ENABLE);
+ } else {
+ mtu3_clrbits(mtu->mac_base, U3D_POWER_MANAGEMENT,
+ SOFT_CONN | SUSPENDM_ENABLE);
+ }
+ dev_dbg(mtu->dev, "SOFTCONN = %d\n", !!enable);
+}
+
+/* only port0 of U2/U3 supports device mode */
+static int mtu3_device_enable(struct mtu3 *mtu)
+{
+ void __iomem *ibase = mtu->ippc_base;
+ u32 check_clk = 0;
+
+ mtu3_clrbits(ibase, U3D_SSUSB_IP_PW_CTRL2, SSUSB_IP_DEV_PDN);
+
+ if (mtu->is_u3_ip) {
+ check_clk = SSUSB_U3_MAC_RST_B_STS;
+ mtu3_clrbits(ibase, SSUSB_U3_CTRL(0),
+ (SSUSB_U3_PORT_DIS | SSUSB_U3_PORT_PDN |
+ SSUSB_U3_PORT_HOST_SEL));
+ }
+ mtu3_clrbits(ibase, SSUSB_U2_CTRL(0),
+ (SSUSB_U2_PORT_DIS | SSUSB_U2_PORT_PDN |
+ SSUSB_U2_PORT_HOST_SEL));
+
+ return ssusb_check_clocks(mtu->ssusb, check_clk);
+}
+
+static void mtu3_device_disable(struct mtu3 *mtu)
+{
+ void __iomem *ibase = mtu->ippc_base;
+
+ if (mtu->is_u3_ip)
+ mtu3_setbits(ibase, SSUSB_U3_CTRL(0),
+ (SSUSB_U3_PORT_DIS | SSUSB_U3_PORT_PDN));
+
+ mtu3_setbits(ibase, SSUSB_U2_CTRL(0),
+ SSUSB_U2_PORT_DIS | SSUSB_U2_PORT_PDN);
+
+ mtu3_setbits(ibase, U3D_SSUSB_IP_PW_CTRL2, SSUSB_IP_DEV_PDN);
+}
+
+/* reset U3D's device module. */
+static void mtu3_device_reset(struct mtu3 *mtu)
+{
+ void __iomem *ibase = mtu->ippc_base;
+
+ mtu3_setbits(ibase, U3D_SSUSB_DEV_RST_CTRL, SSUSB_DEV_SW_RST);
+ udelay(1);
+ mtu3_clrbits(ibase, U3D_SSUSB_DEV_RST_CTRL, SSUSB_DEV_SW_RST);
+}
+
+static void mtu3_intr_status_clear(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+
+ /* Clear EP0 and Tx/Rx EPn interrupts status */
+ mtu3_writel(mbase, U3D_EPISR, ~0x0);
+ /* Clear U2 USB common interrupts status */
+ mtu3_writel(mbase, U3D_COMMON_USB_INTR, ~0x0);
+ /* Clear U3 LTSSM interrupts status */
+ mtu3_writel(mbase, U3D_LTSSM_INTR, ~0x0);
+ /* Clear speed change interrupt status */
+ mtu3_writel(mbase, U3D_DEV_LINK_INTR, ~0x0);
+ /* Clear QMU interrupt status */
+ mtu3_writel(mbase, U3D_QISAR0, ~0x0);
+}
+
+/* disable all interrupts */
+static void mtu3_intr_disable(struct mtu3 *mtu)
+{
+ /* Disable level 1 interrupts */
+ mtu3_writel(mtu->mac_base, U3D_LV1IECR, ~0x0);
+ /* Disable endpoint interrupts */
+ mtu3_writel(mtu->mac_base, U3D_EPIECR, ~0x0);
+ mtu3_intr_status_clear(mtu);
+}
+
+/* enable system global interrupt */
+static void mtu3_intr_enable(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+ u32 value;
+
+ /*Enable level 1 interrupts (BMU, QMU, MAC3, DMA, MAC2, EPCTL) */
+ value = BMU_INTR | QMU_INTR | MAC3_INTR | MAC2_INTR | EP_CTRL_INTR;
+ mtu3_writel(mbase, U3D_LV1IESR, value);
+
+ /* Enable U2 common USB interrupts */
+ value = SUSPEND_INTR | RESUME_INTR | RESET_INTR;
+ mtu3_writel(mbase, U3D_COMMON_USB_INTR_ENABLE, value);
+
+ if (mtu->is_u3_ip) {
+ /* Enable U3 LTSSM interrupts */
+ value = HOT_RST_INTR | WARM_RST_INTR |
+ ENTER_U3_INTR | EXIT_U3_INTR;
+ mtu3_writel(mbase, U3D_LTSSM_INTR_ENABLE, value);
+ }
+
+ /* Enable QMU interrupts. */
+ value = TXQ_CSERR_INT | TXQ_LENERR_INT | RXQ_CSERR_INT |
+ RXQ_LENERR_INT | RXQ_ZLPERR_INT;
+ mtu3_writel(mbase, U3D_QIESR1, value);
+
+ /* Enable speed change interrupt */
+ mtu3_writel(mbase, U3D_DEV_LINK_INTR_ENABLE, SSUSB_DEV_SPEED_CHG_INTR);
+}
+
+void mtu3_set_speed(struct mtu3 *mtu, enum usb_device_speed speed)
+{
+ void __iomem *mbase = mtu->mac_base;
+
+ if (speed > mtu->max_speed)
+ speed = mtu->max_speed;
+
+ switch (speed) {
+ case USB_SPEED_FULL:
+ /* disable U3 SS function */
+ mtu3_clrbits(mbase, U3D_USB3_CONFIG, USB3_EN);
+ /* disable HS function */
+ mtu3_clrbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
+ break;
+ case USB_SPEED_HIGH:
+ mtu3_clrbits(mbase, U3D_USB3_CONFIG, USB3_EN);
+ /* HS/FS detected by HW */
+ mtu3_setbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
+ break;
+ case USB_SPEED_SUPER:
+ mtu3_clrbits(mtu->ippc_base, SSUSB_U3_CTRL(0),
+ SSUSB_U3_PORT_SSP_SPEED);
+ break;
+ case USB_SPEED_SUPER_PLUS:
+ mtu3_setbits(mtu->ippc_base, SSUSB_U3_CTRL(0),
+ SSUSB_U3_PORT_SSP_SPEED);
+ break;
+ default:
+ dev_err(mtu->dev, "invalid speed: %d\n", speed);
+ return;
+ }
+
+ mtu->speed = speed;
+ dev_dbg(mtu->dev, "set speed: %s\n", usb_speed_string(mtu->speed));
+}
+
+/* reset: u2 - data toggle, u3 - SeqN, flow control status etc */
+static void mtu3_ep_reset(struct mtu3_ep *mep)
+{
+ struct mtu3 *mtu = mep->mtu;
+ u32 rst_bit = EP_RST(mep->is_in, mep->epnum);
+
+ mtu3_setbits(mtu->mac_base, U3D_EP_RST, rst_bit);
+ mtu3_clrbits(mtu->mac_base, U3D_EP_RST, rst_bit);
+}
+
+/* set/clear the stall and toggle bits for non-ep0 */
+void mtu3_ep_stall_set(struct mtu3_ep *mep, bool set)
+{
+ struct mtu3 *mtu = mep->mtu;
+ void __iomem *mbase = mtu->mac_base;
+ u8 epnum = mep->epnum;
+ u32 csr;
+
+ if (mep->is_in) { /* TX */
+ csr = mtu3_readl(mbase, MU3D_EP_TXCR0(epnum)) & TX_W1C_BITS;
+ if (set)
+ csr |= TX_SENDSTALL;
+ else
+ csr = (csr & (~TX_SENDSTALL)) | TX_SENTSTALL;
+ mtu3_writel(mbase, MU3D_EP_TXCR0(epnum), csr);
+ } else { /* RX */
+ csr = mtu3_readl(mbase, MU3D_EP_RXCR0(epnum)) & RX_W1C_BITS;
+ if (set)
+ csr |= RX_SENDSTALL;
+ else
+ csr = (csr & (~RX_SENDSTALL)) | RX_SENTSTALL;
+ mtu3_writel(mbase, MU3D_EP_RXCR0(epnum), csr);
+ }
+
+ if (!set) {
+ mtu3_ep_reset(mep);
+ mep->flags &= ~MTU3_EP_STALL;
+ } else {
+ mep->flags |= MTU3_EP_STALL;
+ }
+
+ dev_dbg(mtu->dev, "%s: %s\n", mep->name,
+ set ? "SEND STALL" : "CLEAR STALL, with EP RESET");
+}
+
+void mtu3_dev_on_off(struct mtu3 *mtu, int is_on)
+{
+ if (mtu->is_u3_ip && mtu->speed >= USB_SPEED_SUPER)
+ mtu3_ss_func_set(mtu, is_on);
+ else
+ mtu3_hs_softconn_set(mtu, is_on);
+
+ dev_info(mtu->dev, "gadget (%s) pullup D%s\n",
+ usb_speed_string(mtu->speed), is_on ? "+" : "-");
+}
+
+void mtu3_start(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+
+ dev_dbg(mtu->dev, "%s devctl 0x%x\n", __func__,
+ mtu3_readl(mbase, U3D_DEVICE_CONTROL));
+
+ /* Initialize the default interrupts */
+ mtu3_intr_enable(mtu);
+ mtu->is_active = 1;
+
+ if (mtu->softconnect)
+ mtu3_dev_on_off(mtu, 1);
+}
+
+void mtu3_stop(struct mtu3 *mtu)
+{
+ dev_dbg(mtu->dev, "%s\n", __func__);
+
+ mtu3_intr_disable(mtu);
+
+ if (mtu->softconnect)
+ mtu3_dev_on_off(mtu, 0);
+
+ mtu->is_active = 0;
+}
+
+/* for non-ep0 */
+int mtu3_config_ep(struct mtu3 *mtu, struct mtu3_ep *mep,
+ int interval, int burst, int mult)
+{
+ void __iomem *mbase = mtu->mac_base;
+ bool gen2cp = mtu->gen2cp;
+ int epnum = mep->epnum;
+ u32 csr0, csr1, csr2;
+ int fifo_sgsz, fifo_addr;
+ int num_pkts;
+
+ fifo_addr = ep_fifo_alloc(mep, mep->maxp);
+ if (fifo_addr < 0) {
+ dev_err(mtu->dev, "alloc ep fifo failed(%d)\n", mep->maxp);
+ return -ENOMEM;
+ }
+ fifo_sgsz = ilog2(mep->fifo_seg_size);
+ dev_dbg(mtu->dev, "%s fifosz: %x(%x/%x)\n", __func__, fifo_sgsz,
+ mep->fifo_seg_size, mep->fifo_size);
+
+ if (mep->is_in) {
+ csr0 = TX_TXMAXPKTSZ(mep->maxp);
+ csr0 |= TX_DMAREQEN;
+
+ num_pkts = (burst + 1) * (mult + 1) - 1;
+ csr1 = TX_SS_BURST(burst) | TX_SLOT(mep->slot);
+ csr1 |= TX_MAX_PKT(gen2cp, num_pkts) | TX_MULT(gen2cp, mult);
+
+ csr2 = TX_FIFOADDR(fifo_addr >> 4);
+ csr2 |= TX_FIFOSEGSIZE(fifo_sgsz);
+
+ switch (mep->type) {
+ case USB_ENDPOINT_XFER_BULK:
+ csr1 |= TX_TYPE(TYPE_BULK);
+ break;
+ case USB_ENDPOINT_XFER_ISOC:
+ csr1 |= TX_TYPE(TYPE_ISO);
+ csr2 |= TX_BINTERVAL(interval);
+ break;
+ case USB_ENDPOINT_XFER_INT:
+ csr1 |= TX_TYPE(TYPE_INT);
+ csr2 |= TX_BINTERVAL(interval);
+ break;
+ }
+
+ /* Enable QMU Done interrupt */
+ mtu3_setbits(mbase, U3D_QIESR0, QMU_TX_DONE_INT(epnum));
+
+ mtu3_writel(mbase, MU3D_EP_TXCR0(epnum), csr0);
+ mtu3_writel(mbase, MU3D_EP_TXCR1(epnum), csr1);
+ mtu3_writel(mbase, MU3D_EP_TXCR2(epnum), csr2);
+
+ dev_dbg(mtu->dev, "U3D_TX%d CSR0:%#x, CSR1:%#x, CSR2:%#x\n",
+ epnum, mtu3_readl(mbase, MU3D_EP_TXCR0(epnum)),
+ mtu3_readl(mbase, MU3D_EP_TXCR1(epnum)),
+ mtu3_readl(mbase, MU3D_EP_TXCR2(epnum)));
+ } else {
+ csr0 = RX_RXMAXPKTSZ(mep->maxp);
+ csr0 |= RX_DMAREQEN;
+
+ num_pkts = (burst + 1) * (mult + 1) - 1;
+ csr1 = RX_SS_BURST(burst) | RX_SLOT(mep->slot);
+ csr1 |= RX_MAX_PKT(gen2cp, num_pkts) | RX_MULT(gen2cp, mult);
+
+ csr2 = RX_FIFOADDR(fifo_addr >> 4);
+ csr2 |= RX_FIFOSEGSIZE(fifo_sgsz);
+
+ switch (mep->type) {
+ case USB_ENDPOINT_XFER_BULK:
+ csr1 |= RX_TYPE(TYPE_BULK);
+ break;
+ case USB_ENDPOINT_XFER_ISOC:
+ csr1 |= RX_TYPE(TYPE_ISO);
+ csr2 |= RX_BINTERVAL(interval);
+ break;
+ case USB_ENDPOINT_XFER_INT:
+ csr1 |= RX_TYPE(TYPE_INT);
+ csr2 |= RX_BINTERVAL(interval);
+ break;
+ }
+
+ /*Enable QMU Done interrupt */
+ mtu3_setbits(mbase, U3D_QIESR0, QMU_RX_DONE_INT(epnum));
+
+ mtu3_writel(mbase, MU3D_EP_RXCR0(epnum), csr0);
+ mtu3_writel(mbase, MU3D_EP_RXCR1(epnum), csr1);
+ mtu3_writel(mbase, MU3D_EP_RXCR2(epnum), csr2);
+
+ dev_dbg(mtu->dev, "U3D_RX%d CSR0:%#x, CSR1:%#x, CSR2:%#x\n",
+ epnum, mtu3_readl(mbase, MU3D_EP_RXCR0(epnum)),
+ mtu3_readl(mbase, MU3D_EP_RXCR1(epnum)),
+ mtu3_readl(mbase, MU3D_EP_RXCR2(epnum)));
+ }
+
+ dev_dbg(mtu->dev, "csr0:%#x, csr1:%#x, csr2:%#x\n", csr0, csr1, csr2);
+ dev_dbg(mtu->dev, "%s: %s, fifo-addr:%#x, fifo-size:%#x(%#x/%#x)\n",
+ __func__, mep->name, mep->fifo_addr, mep->fifo_size,
+ fifo_sgsz, mep->fifo_seg_size);
+
+ return 0;
+}
+
+/* for non-ep0 */
+void mtu3_deconfig_ep(struct mtu3 *mtu, struct mtu3_ep *mep)
+{
+ void __iomem *mbase = mtu->mac_base;
+ int epnum = mep->epnum;
+
+ if (mep->is_in) {
+ mtu3_writel(mbase, MU3D_EP_TXCR0(epnum), 0);
+ mtu3_writel(mbase, MU3D_EP_TXCR1(epnum), 0);
+ mtu3_writel(mbase, MU3D_EP_TXCR2(epnum), 0);
+ mtu3_setbits(mbase, U3D_QIECR0, QMU_TX_DONE_INT(epnum));
+ } else {
+ mtu3_writel(mbase, MU3D_EP_RXCR0(epnum), 0);
+ mtu3_writel(mbase, MU3D_EP_RXCR1(epnum), 0);
+ mtu3_writel(mbase, MU3D_EP_RXCR2(epnum), 0);
+ mtu3_setbits(mbase, U3D_QIECR0, QMU_RX_DONE_INT(epnum));
+ }
+
+ mtu3_ep_reset(mep);
+ ep_fifo_free(mep);
+
+ dev_dbg(mtu->dev, "%s: %s\n", __func__, mep->name);
+}
+
+/*
+ * Two scenarios:
+ * 1. when device IP supports SS, the fifo of EP0, TX EPs, RX EPs
+ * are separated;
+ * 2. when supports only HS, the fifo is shared for all EPs, and
+ * the capability registers of @EPNTXFFSZ or @EPNRXFFSZ indicate
+ * the total fifo size of non-ep0, and ep0's is fixed to 64B,
+ * so the total fifo size is 64B + @EPNTXFFSZ;
+ * Due to the first 64B should be reserved for EP0, non-ep0's fifo
+ * starts from offset 64 and are divided into two equal parts for
+ * TX or RX EPs for simplification.
+ */
+static void get_ep_fifo_config(struct mtu3 *mtu)
+{
+ struct mtu3_fifo_info *tx_fifo;
+ struct mtu3_fifo_info *rx_fifo;
+ u32 fifosize;
+
+ if (mtu->is_u3_ip) {
+ fifosize = mtu3_readl(mtu->mac_base, U3D_CAP_EPNTXFFSZ);
+ tx_fifo = &mtu->tx_fifo;
+ tx_fifo->base = 0;
+ tx_fifo->limit = fifosize / MTU3_U3IP_EP_FIFO_UNIT;
+ bitmap_zero(tx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
+
+ fifosize = mtu3_readl(mtu->mac_base, U3D_CAP_EPNRXFFSZ);
+ rx_fifo = &mtu->rx_fifo;
+ rx_fifo->base = 0;
+ rx_fifo->limit = fifosize / MTU3_U3IP_EP_FIFO_UNIT;
+ bitmap_zero(rx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
+ mtu->slot = MTU3_U3_IP_SLOT_DEFAULT;
+ } else {
+ fifosize = mtu3_readl(mtu->mac_base, U3D_CAP_EPNTXFFSZ);
+ tx_fifo = &mtu->tx_fifo;
+ tx_fifo->base = MTU3_U2_IP_EP0_FIFO_SIZE;
+ tx_fifo->limit = (fifosize / MTU3_U2IP_EP_FIFO_UNIT) >> 1;
+ bitmap_zero(tx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
+
+ rx_fifo = &mtu->rx_fifo;
+ rx_fifo->base = tx_fifo->base +
+ tx_fifo->limit * MTU3_U2IP_EP_FIFO_UNIT;
+ rx_fifo->limit = tx_fifo->limit;
+ bitmap_zero(rx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
+ mtu->slot = MTU3_U2_IP_SLOT_DEFAULT;
+ }
+
+ dev_dbg(mtu->dev, "%s, TX: base-%d, limit-%d; RX: base-%d, limit-%d\n",
+ __func__, tx_fifo->base, tx_fifo->limit,
+ rx_fifo->base, rx_fifo->limit);
+}
+
+void mtu3_ep0_setup(struct mtu3 *mtu)
+{
+ u32 maxpacket = mtu->g.ep0->maxpacket;
+ u32 csr;
+
+ dev_dbg(mtu->dev, "%s maxpacket: %d\n", __func__, maxpacket);
+
+ csr = mtu3_readl(mtu->mac_base, U3D_EP0CSR);
+ csr &= ~EP0_MAXPKTSZ_MSK;
+ csr |= EP0_MAXPKTSZ(maxpacket);
+ csr &= EP0_W1C_BITS;
+ mtu3_writel(mtu->mac_base, U3D_EP0CSR, csr);
+
+ /* Enable EP0 interrupt */
+ mtu3_writel(mtu->mac_base, U3D_EPIESR, EP0ISR | SETUPENDISR);
+}
+
+static int mtu3_mem_alloc(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+ struct mtu3_ep *ep_array;
+ int in_ep_num, out_ep_num;
+ u32 cap_epinfo;
+ int i;
+
+ cap_epinfo = mtu3_readl(mbase, U3D_CAP_EPINFO);
+ in_ep_num = CAP_TX_EP_NUM(cap_epinfo);
+ out_ep_num = CAP_RX_EP_NUM(cap_epinfo);
+
+ dev_info(mtu->dev, "fifosz/epnum: Tx=%#x/%d, Rx=%#x/%d\n",
+ mtu3_readl(mbase, U3D_CAP_EPNTXFFSZ), in_ep_num,
+ mtu3_readl(mbase, U3D_CAP_EPNRXFFSZ), out_ep_num);
+
+ /* one for ep0, another is reserved */
+ mtu->num_eps = min(in_ep_num, out_ep_num) + 1;
+ ep_array = kcalloc(mtu->num_eps * 2, sizeof(*ep_array), GFP_KERNEL);
+ if (!ep_array)
+ return -ENOMEM;
+
+ mtu->ep_array = ep_array;
+ mtu->in_eps = ep_array;
+ mtu->out_eps = &ep_array[mtu->num_eps];
+ /* ep0 uses in_eps[0], out_eps[0] is reserved */
+ mtu->ep0 = mtu->in_eps;
+ mtu->ep0->mtu = mtu;
+ mtu->ep0->epnum = 0;
+
+ for (i = 1; i < mtu->num_eps; i++) {
+ struct mtu3_ep *mep = mtu->in_eps + i;
+
+ mep->fifo = &mtu->tx_fifo;
+ mep = mtu->out_eps + i;
+ mep->fifo = &mtu->rx_fifo;
+ }
+
+ get_ep_fifo_config(mtu);
+ mtu3_qmu_init(mtu);
+
+ return 0;
+}
+
+static void mtu3_mem_free(struct mtu3 *mtu)
+{
+ mtu3_qmu_exit(mtu);
+ kfree(mtu->ep_array);
+}
+
+static void mtu3_regs_init(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+
+ /* be sure interrupts are disabled before registration of ISR */
+ mtu3_intr_disable(mtu);
+
+ if (mtu->is_u3_ip) {
+ /* disable LGO_U1/U2 by default */
+ mtu3_clrbits(mbase, U3D_LINK_POWER_CONTROL,
+ SW_U1_REQUEST_ENABLE | SW_U2_REQUEST_ENABLE);
+ /* enable accept LGO_U1/U2 link command from host */
+ mtu3_setbits(mbase, U3D_LINK_POWER_CONTROL,
+ SW_U1_ACCEPT_ENABLE | SW_U2_ACCEPT_ENABLE);
+ /* device responses to u3_exit from host automatically */
+ mtu3_clrbits(mbase, U3D_LTSSM_CTRL, SOFT_U3_EXIT_EN);
+ /* automatically build U2 link when U3 detect fail */
+ mtu3_setbits(mbase, U3D_USB2_TEST_MODE, U2U3_AUTO_SWITCH);
+ /* auto clear SOFT_CONN when clear USB3_EN if work as HS */
+ mtu3_setbits(mbase, U3D_U3U2_SWITCH_CTRL, SOFTCON_CLR_AUTO_EN);
+ }
+
+ /* delay about 0.1us from detecting reset to send chirp-K */
+ mtu3_clrbits(mbase, U3D_LINK_RESET_INFO, WTCHRP_MSK);
+ /* U2/U3 detected by HW */
+ mtu3_writel(mbase, U3D_DEVICE_CONF, 0);
+ /* enable automatical HWRW from L1 */
+ mtu3_setbits(mbase, U3D_POWER_MANAGEMENT, LPM_HRWE);
+
+ mtu3_set_speed(mtu, mtu->max_speed);
+ ssusb_set_force_mode(mtu->ssusb, MTU3_DR_FORCE_DEVICE);
+
+ if (mtu->force_vbus)
+ mtu3_setbits(mbase, U3D_MISC_CTRL, VBUS_FRC_EN | VBUS_ON);
+ else /* vbus detected by HW */
+ mtu3_clrbits(mbase, U3D_MISC_CTRL, VBUS_FRC_EN | VBUS_ON);
+}
+
+static irqreturn_t mtu3_link_isr(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+ enum usb_device_speed udev_speed;
+ u32 maxpkt = 64;
+ u32 link;
+ u32 speed;
+
+ link = mtu3_readl(mbase, U3D_DEV_LINK_INTR);
+ link &= mtu3_readl(mbase, U3D_DEV_LINK_INTR_ENABLE);
+ mtu3_writel(mbase, U3D_DEV_LINK_INTR, link); /* W1C */
+ dev_dbg(mtu->dev, "=== LINK[%x] ===\n", link);
+
+ if (!(link & SSUSB_DEV_SPEED_CHG_INTR))
+ return IRQ_NONE;
+
+ speed = SSUSB_DEV_SPEED(mtu3_readl(mbase, U3D_DEVICE_CONF));
+
+ switch (speed) {
+ case MTU3_SPEED_FULL:
+ udev_speed = USB_SPEED_FULL;
+ /*BESLCK = 4 < BESLCK_U3 = 10 < BESLDCK = 15 */
+ mtu3_writel(mbase, U3D_USB20_LPM_PARAMETER, LPM_BESLDCK(0xf)
+ | LPM_BESLCK(4) | LPM_BESLCK_U3(0xa));
+ mtu3_setbits(mbase, U3D_POWER_MANAGEMENT,
+ LPM_BESL_STALL | LPM_BESLD_STALL);
+ break;
+ case MTU3_SPEED_HIGH:
+ udev_speed = USB_SPEED_HIGH;
+ /*BESLCK = 4 < BESLCK_U3 = 10 < BESLDCK = 15 */
+ mtu3_writel(mbase, U3D_USB20_LPM_PARAMETER, LPM_BESLDCK(0xf)
+ | LPM_BESLCK(4) | LPM_BESLCK_U3(0xa));
+ mtu3_setbits(mbase, U3D_POWER_MANAGEMENT,
+ LPM_BESL_STALL | LPM_BESLD_STALL);
+ break;
+ case MTU3_SPEED_SUPER:
+ udev_speed = USB_SPEED_SUPER;
+ maxpkt = 512;
+ break;
+ case MTU3_SPEED_SUPER_PLUS:
+ udev_speed = USB_SPEED_SUPER_PLUS;
+ maxpkt = 512;
+ break;
+ default:
+ udev_speed = USB_SPEED_UNKNOWN;
+ break;
+ }
+ dev_dbg(mtu->dev, "%s: %s\n", __func__, usb_speed_string(udev_speed));
+
+ mtu->g.speed = udev_speed;
+ mtu->g.ep0->maxpacket = maxpkt;
+ mtu->ep0_state = MU3D_EP0_STATE_SETUP;
+
+ if (udev_speed == USB_SPEED_UNKNOWN)
+ mtu3_gadget_disconnect(mtu);
+ else
+ mtu3_ep0_setup(mtu);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t mtu3_u3_ltssm_isr(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+ u32 ltssm;
+
+ ltssm = mtu3_readl(mbase, U3D_LTSSM_INTR);
+ ltssm &= mtu3_readl(mbase, U3D_LTSSM_INTR_ENABLE);
+ mtu3_writel(mbase, U3D_LTSSM_INTR, ltssm); /* W1C */
+ dev_dbg(mtu->dev, "=== LTSSM[%x] ===\n", ltssm);
+
+ if (ltssm & (HOT_RST_INTR | WARM_RST_INTR))
+ mtu3_gadget_reset(mtu);
+
+ if (ltssm & VBUS_FALL_INTR) {
+ mtu3_ss_func_set(mtu, false);
+ mtu3_gadget_reset(mtu);
+ }
+
+ if (ltssm & VBUS_RISE_INTR)
+ mtu3_ss_func_set(mtu, true);
+
+ if (ltssm & EXIT_U3_INTR)
+ mtu3_gadget_resume(mtu);
+
+ if (ltssm & ENTER_U3_INTR)
+ mtu3_gadget_suspend(mtu);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t mtu3_u2_common_isr(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+ u32 u2comm;
+
+ u2comm = mtu3_readl(mbase, U3D_COMMON_USB_INTR);
+ u2comm &= mtu3_readl(mbase, U3D_COMMON_USB_INTR_ENABLE);
+ mtu3_writel(mbase, U3D_COMMON_USB_INTR, u2comm); /* W1C */
+ dev_dbg(mtu->dev, "=== U2COMM[%x] ===\n", u2comm);
+
+ if (u2comm & SUSPEND_INTR)
+ mtu3_gadget_suspend(mtu);
+
+ if (u2comm & RESUME_INTR)
+ mtu3_gadget_resume(mtu);
+
+ if (u2comm & RESET_INTR)
+ mtu3_gadget_reset(mtu);
+
+ return IRQ_HANDLED;
+}
+
+irqreturn_t mtu3_irq(int irq, void *data)
+{
+ struct mtu3 *mtu = (struct mtu3 *)data;
+ unsigned long flags;
+ u32 level1;
+
+ spin_lock_irqsave(&mtu->lock, flags);
+
+ /* U3D_LV1ISR is RU */
+ level1 = mtu3_readl(mtu->mac_base, U3D_LV1ISR);
+ level1 &= mtu3_readl(mtu->mac_base, U3D_LV1IER);
+
+ if (level1 & EP_CTRL_INTR)
+ mtu3_link_isr(mtu);
+
+ if (level1 & MAC2_INTR)
+ mtu3_u2_common_isr(mtu);
+
+ if (level1 & MAC3_INTR)
+ mtu3_u3_ltssm_isr(mtu);
+
+ if (level1 & BMU_INTR)
+ mtu3_ep0_isr(mtu);
+
+ if (level1 & QMU_INTR)
+ mtu3_qmu_isr(mtu);
+
+ spin_unlock_irqrestore(&mtu->lock, flags);
+
+ return IRQ_HANDLED;
+}
+
+static void mtu3_check_params(struct mtu3 *mtu)
+{
+ /* check the max_speed parameter */
+ switch (mtu->max_speed) {
+ case USB_SPEED_FULL:
+ case USB_SPEED_HIGH:
+ case USB_SPEED_SUPER:
+ case USB_SPEED_SUPER_PLUS:
+ break;
+ default:
+ dev_err(mtu->dev, "invalid max_speed: %d\n", mtu->max_speed);
+ /* fall through */
+ case USB_SPEED_UNKNOWN:
+ /* default as SS */
+ mtu->max_speed = USB_SPEED_SUPER;
+ break;
+ }
+
+ if (!mtu->is_u3_ip && (mtu->max_speed > USB_SPEED_HIGH))
+ mtu->max_speed = USB_SPEED_HIGH;
+
+ mtu->speed = mtu->max_speed;
+
+ dev_info(mtu->dev, "max_speed: %s\n", usb_speed_string(mtu->speed));
+}
+
+static int mtu3_hw_init(struct mtu3 *mtu)
+{
+ u32 value;
+ int ret;
+
+ value = mtu3_readl(mtu->ippc_base, U3D_SSUSB_IP_TRUNK_VERS);
+ mtu->hw_version = IP_TRUNK_VERS(value);
+ mtu->gen2cp = !!(mtu->hw_version >= MTU3_TRUNK_VERS_1003);
+
+ value = mtu3_readl(mtu->ippc_base, U3D_SSUSB_IP_DEV_CAP);
+ mtu->is_u3_ip = !!SSUSB_IP_DEV_U3_PORT_NUM(value);
+
+ dev_info(mtu->dev, "IP version 0x%x(%s IP)\n", mtu->hw_version,
+ mtu->is_u3_ip ? "U3" : "U2");
+
+ mtu3_check_params(mtu);
+
+ mtu3_device_reset(mtu);
+
+ ret = mtu3_device_enable(mtu);
+ if (ret) {
+ dev_err(mtu->dev, "device enable failed %d\n", ret);
+ return ret;
+ }
+
+ ret = mtu3_mem_alloc(mtu);
+ if (ret)
+ return ret;
+
+ mtu3_regs_init(mtu);
+
+ return 0;
+}
+
+static void mtu3_hw_exit(struct mtu3 *mtu)
+{
+ mtu3_device_disable(mtu);
+ mtu3_mem_free(mtu);
+}
+
+int ssusb_gadget_init(struct ssusb_mtk *ssusb)
+{
+ struct mtu3 *mtu = ssusb->u3d;
+ struct udevice *dev = mtu->dev;
+ int ret = -ENOMEM;
+
+ spin_lock_init(&mtu->lock);
+ mtu->ippc_base = ssusb->ippc_base;
+ mtu->mac_base = ssusb->mac_base;
+ mtu->ssusb = ssusb;
+ mtu->max_speed = usb_get_maximum_speed(dev->node);
+ mtu->force_vbus = dev_read_bool(dev, "mediatek,force-vbus");
+
+ ret = mtu3_hw_init(mtu);
+ if (ret) {
+ dev_err(dev, "mtu3 hw init failed:%d\n", ret);
+ return ret;
+ }
+
+ ret = mtu3_gadget_setup(mtu);
+ if (ret) {
+ dev_err(dev, "mtu3 gadget init failed:%d\n", ret);
+ goto gadget_err;
+ }
+
+ dev_info(dev, "%s() done...\n", __func__);
+
+ return 0;
+
+gadget_err:
+ mtu3_hw_exit(mtu);
+ ssusb->u3d = NULL;
+ dev_err(dev, "%s() fail...\n", __func__);
+
+ return ret;
+}
+
+void ssusb_gadget_exit(struct ssusb_mtk *ssusb)
+{
+ struct mtu3 *mtu = ssusb->u3d;
+
+ mtu3_gadget_cleanup(mtu);
+ mtu3_hw_exit(mtu);
+}
diff --git a/drivers/usb/mtu3/mtu3_dr.h b/drivers/usb/mtu3/mtu3_dr.h
new file mode 100644
index 0000000..ec0e50c
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3_dr.h
@@ -0,0 +1,52 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * mtu3_dr.h - dual role switch and host glue layer header
+ *
+ * Copyright (C) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+#ifndef _MTU3_DR_H_
+#define _MTU3_DR_H_
+
+#if IS_ENABLED(CONFIG_USB_MTU3_HOST)
+
+int ssusb_host_init(struct ssusb_mtk *ssusb);
+void ssusb_host_exit(struct ssusb_mtk *ssusb);
+
+#else
+
+static inline int ssusb_host_init(struct ssusb_mtk *ssusb)
+{
+ return 0;
+}
+
+static inline void ssusb_host_exit(struct ssusb_mtk *ssusb)
+{}
+
+#endif
+
+#if IS_ENABLED(CONFIG_USB_MTU3_GADGET)
+int ssusb_gadget_init(struct ssusb_mtk *ssusb);
+void ssusb_gadget_exit(struct ssusb_mtk *ssusb);
+irqreturn_t mtu3_irq(int irq, void *data);
+#else
+static inline int ssusb_gadget_init(struct ssusb_mtk *ssusb)
+{
+ return 0;
+}
+
+static inline void ssusb_gadget_exit(struct ssusb_mtk *ssusb)
+{}
+
+static inline irqreturn_t mtu3_irq(int irq, void *data)
+{
+ return IRQ_NONE;
+}
+#endif
+
+void ssusb_set_force_mode(struct ssusb_mtk *ssusb,
+ enum mtu3_dr_force_mode mode);
+
+#endif /* _MTU3_DR_H_ */
diff --git a/drivers/usb/mtu3/mtu3_gadget.c b/drivers/usb/mtu3/mtu3_gadget.c
new file mode 100644
index 0000000..027b7e6
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3_gadget.c
@@ -0,0 +1,686 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * mtu3_gadget.c - MediaTek usb3 DRD peripheral support
+ *
+ * Copyright (C) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+#include "mtu3.h"
+
+void mtu3_req_complete(struct mtu3_ep *mep,
+ struct usb_request *req, int status)
+__releases(mep->mtu->lock)
+__acquires(mep->mtu->lock)
+{
+ struct mtu3_request *mreq = to_mtu3_request(req);
+ struct mtu3 *mtu = mreq->mtu;
+
+ list_del(&mreq->list);
+ if (req->status == -EINPROGRESS)
+ req->status = status;
+
+ spin_unlock(&mtu->lock);
+
+ /* ep0 makes use of PIO, needn't unmap it */
+ if (mep->epnum)
+ usb_gadget_unmap_request(&mtu->g, req, mep->is_in);
+
+ dev_dbg(mtu->dev, "%s complete req: %p, sts %d, %d/%d\n",
+ mep->name, req, req->status, req->actual, req->length);
+
+ usb_gadget_giveback_request(&mep->ep, req);
+ spin_lock(&mtu->lock);
+}
+
+static void nuke(struct mtu3_ep *mep, const int status)
+{
+ struct mtu3_request *mreq = NULL;
+
+ if (list_empty(&mep->req_list))
+ return;
+
+ dev_dbg(mep->mtu->dev, "abort %s's req: sts %d\n", mep->name, status);
+
+ /* exclude EP0 */
+ if (mep->epnum)
+ mtu3_qmu_flush(mep);
+
+ while (!list_empty(&mep->req_list)) {
+ mreq = list_first_entry(&mep->req_list,
+ struct mtu3_request, list);
+ mtu3_req_complete(mep, &mreq->request, status);
+ }
+}
+
+static int mtu3_ep_enable(struct mtu3_ep *mep)
+{
+ const struct usb_endpoint_descriptor *desc;
+ const struct usb_ss_ep_comp_descriptor *comp_desc;
+ struct mtu3 *mtu = mep->mtu;
+ u32 interval = 0;
+ u32 mult = 0;
+ u32 burst = 0;
+ int max_packet;
+ int ret;
+
+ desc = mep->desc;
+ comp_desc = mep->comp_desc;
+ mep->type = usb_endpoint_type(desc);
+ max_packet = usb_endpoint_maxp(desc);
+ mep->maxp = max_packet & GENMASK(10, 0);
+
+ switch (mtu->g.speed) {
+ case USB_SPEED_SUPER:
+ case USB_SPEED_SUPER_PLUS:
+ if (usb_endpoint_xfer_int(desc) ||
+ usb_endpoint_xfer_isoc(desc)) {
+ interval = desc->bInterval;
+ interval = clamp_val(interval, 1, 16) - 1;
+ if (usb_endpoint_xfer_isoc(desc) && comp_desc)
+ mult = comp_desc->bmAttributes;
+ }
+ if (comp_desc)
+ burst = comp_desc->bMaxBurst;
+
+ break;
+ case USB_SPEED_HIGH:
+ if (usb_endpoint_xfer_isoc(desc) ||
+ usb_endpoint_xfer_int(desc)) {
+ interval = desc->bInterval;
+ interval = clamp_val(interval, 1, 16) - 1;
+ burst = (max_packet & GENMASK(12, 11)) >> 11;
+ }
+ break;
+ default:
+ break; /*others are ignored */
+ }
+
+ dev_dbg(mtu->dev, "%s maxp:%d, interval:%d, burst:%d, mult:%d\n",
+ __func__, mep->maxp, interval, burst, mult);
+
+ mep->ep.maxpacket = mep->maxp;
+ mep->ep.desc = desc;
+ mep->ep.comp_desc = comp_desc;
+ mep->slot = mtu->slot;
+
+ ret = mtu3_config_ep(mtu, mep, interval, burst, mult);
+ if (ret < 0)
+ return ret;
+
+ ret = mtu3_gpd_ring_alloc(mep);
+ if (ret < 0) {
+ mtu3_deconfig_ep(mtu, mep);
+ return ret;
+ }
+
+ mtu3_qmu_start(mep);
+
+ return 0;
+}
+
+static int mtu3_ep_disable(struct mtu3_ep *mep)
+{
+ struct mtu3 *mtu = mep->mtu;
+
+ mtu3_qmu_stop(mep);
+
+ /* abort all pending requests */
+ nuke(mep, -ESHUTDOWN);
+ mtu3_deconfig_ep(mtu, mep);
+ mtu3_gpd_ring_free(mep);
+
+ mep->desc = NULL;
+ mep->ep.desc = NULL;
+ mep->comp_desc = NULL;
+ mep->type = 0;
+ mep->flags = 0;
+
+ return 0;
+}
+
+static int mtu3_gadget_ep_enable(struct usb_ep *ep,
+ const struct usb_endpoint_descriptor *desc)
+{
+ struct mtu3_ep *mep;
+ struct mtu3 *mtu;
+ unsigned long flags;
+ int ret = -EINVAL;
+
+ if (!ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT) {
+ pr_debug("%s invalid parameters\n", __func__);
+ return -EINVAL;
+ }
+
+ if (!desc->wMaxPacketSize) {
+ pr_debug("%s missing wMaxPacketSize\n", __func__);
+ return -EINVAL;
+ }
+ mep = to_mtu3_ep(ep);
+ mtu = mep->mtu;
+
+ /* check ep number and direction against endpoint */
+ if (usb_endpoint_num(desc) != mep->epnum)
+ return -EINVAL;
+
+ if (!!usb_endpoint_dir_in(desc) ^ !!mep->is_in)
+ return -EINVAL;
+
+ dev_dbg(mtu->dev, "%s %s\n", __func__, ep->name);
+
+ if (mep->flags & MTU3_EP_ENABLED) {
+ dev_warn(mtu->dev, "%s is already enabled\n", mep->name);
+ return 0;
+ }
+
+ spin_lock_irqsave(&mtu->lock, flags);
+ mep->desc = desc;
+ mep->comp_desc = ep->comp_desc;
+
+ ret = mtu3_ep_enable(mep);
+ if (ret)
+ goto error;
+
+ mep->flags = MTU3_EP_ENABLED;
+ mtu->active_ep++;
+
+error:
+ spin_unlock_irqrestore(&mtu->lock, flags);
+
+ dev_dbg(mtu->dev, "%s active_ep=%d\n", __func__, mtu->active_ep);
+
+ return ret;
+}
+
+static int mtu3_gadget_ep_disable(struct usb_ep *ep)
+{
+ struct mtu3_ep *mep = to_mtu3_ep(ep);
+ struct mtu3 *mtu = mep->mtu;
+ unsigned long flags;
+
+ dev_dbg(mtu->dev, "%s %s\n", __func__, mep->name);
+
+ if (!(mep->flags & MTU3_EP_ENABLED)) {
+ dev_warn(mtu->dev, "%s is already disabled\n", mep->name);
+ return 0;
+ }
+
+ spin_lock_irqsave(&mtu->lock, flags);
+ mtu3_ep_disable(mep);
+ mep->flags = 0;
+ mtu->active_ep--;
+ spin_unlock_irqrestore(&mtu->lock, flags);
+
+ dev_dbg(mtu->dev, "%s active_ep=%d, mtu3 is_active=%d\n",
+ __func__, mtu->active_ep, mtu->is_active);
+
+ return 0;
+}
+
+struct usb_request *mtu3_alloc_request(struct usb_ep *ep, gfp_t gfp_flags)
+{
+ struct mtu3_ep *mep = to_mtu3_ep(ep);
+ struct mtu3_request *mreq;
+
+ mreq = kzalloc(sizeof(*mreq), gfp_flags);
+ if (!mreq)
+ return NULL;
+
+ mreq->request.dma = DMA_ADDR_INVALID;
+ mreq->epnum = mep->epnum;
+ mreq->mep = mep;
+
+ return &mreq->request;
+}
+
+void mtu3_free_request(struct usb_ep *ep, struct usb_request *req)
+{
+ struct mtu3_request *mreq = to_mtu3_request(req);
+
+ kfree(mreq);
+}
+
+static int mtu3_gadget_queue(struct usb_ep *ep,
+ struct usb_request *req, gfp_t gfp_flags)
+{
+ struct mtu3_ep *mep = to_mtu3_ep(ep);
+ struct mtu3_request *mreq = to_mtu3_request(req);
+ struct mtu3 *mtu = mep->mtu;
+ unsigned long flags;
+ int ret = 0;
+
+ if (!req->buf)
+ return -ENODATA;
+
+ if (mreq->mep != mep)
+ return -EINVAL;
+
+ dev_dbg(mtu->dev, "%s %s EP%d(%s), req=%p, maxp=%d, len#%d\n",
+ __func__, mep->is_in ? "TX" : "RX", mreq->epnum, ep->name,
+ mreq, ep->maxpacket, mreq->request.length);
+
+ if (req->length > GPD_BUF_SIZE) {
+ dev_warn(mtu->dev,
+ "req length > supported MAX:%d requested:%d\n",
+ GPD_BUF_SIZE, req->length);
+ return -EOPNOTSUPP;
+ }
+
+ /* don't queue if the ep is down */
+ if (!mep->desc) {
+ dev_dbg(mtu->dev, "req=%p queued to %s while it's disabled\n",
+ req, ep->name);
+ return -ESHUTDOWN;
+ }
+
+ mreq->mtu = mtu;
+ mreq->request.actual = 0;
+ mreq->request.status = -EINPROGRESS;
+
+ ret = usb_gadget_map_request(&mtu->g, req, mep->is_in);
+ if (ret) {
+ dev_err(mtu->dev, "dma mapping failed\n");
+ return ret;
+ }
+
+ spin_lock_irqsave(&mtu->lock, flags);
+
+ if (mtu3_prepare_transfer(mep)) {
+ ret = -EAGAIN;
+ goto error;
+ }
+
+ list_add_tail(&mreq->list, &mep->req_list);
+ mtu3_insert_gpd(mep, mreq);
+ mtu3_qmu_resume(mep);
+
+error:
+ spin_unlock_irqrestore(&mtu->lock, flags);
+
+ return ret;
+}
+
+static int mtu3_gadget_dequeue(struct usb_ep *ep, struct usb_request *req)
+{
+ struct mtu3_ep *mep = to_mtu3_ep(ep);
+ struct mtu3_request *mreq = to_mtu3_request(req);
+ struct mtu3_request *r;
+ struct mtu3 *mtu = mep->mtu;
+ unsigned long flags;
+ int ret = 0;
+
+ if (mreq->mep != mep)
+ return -EINVAL;
+
+ dev_dbg(mtu->dev, "%s : req=%p\n", __func__, req);
+
+ spin_lock_irqsave(&mtu->lock, flags);
+
+ list_for_each_entry(r, &mep->req_list, list) {
+ if (r == mreq)
+ break;
+ }
+ if (r != mreq) {
+ dev_dbg(mtu->dev, "req=%p not queued to %s\n", req, ep->name);
+ ret = -EINVAL;
+ goto done;
+ }
+
+ mtu3_qmu_flush(mep); /* REVISIT: set BPS ?? */
+ mtu3_req_complete(mep, req, -ECONNRESET);
+ mtu3_qmu_start(mep);
+
+done:
+ spin_unlock_irqrestore(&mtu->lock, flags);
+
+ return ret;
+}
+
+/*
+ * Set or clear the halt bit of an EP.
+ * A halted EP won't TX/RX any data but will queue requests.
+ */
+static int mtu3_gadget_ep_set_halt(struct usb_ep *ep, int value)
+{
+ struct mtu3_ep *mep = to_mtu3_ep(ep);
+ struct mtu3 *mtu = mep->mtu;
+ struct mtu3_request *mreq;
+ unsigned long flags = 0;
+ int ret = 0;
+
+ dev_dbg(mtu->dev, "%s : %s...", __func__, ep->name);
+
+ spin_lock_irqsave(&mtu->lock, flags);
+
+ if (mep->type == USB_ENDPOINT_XFER_ISOC) {
+ ret = -EINVAL;
+ goto done;
+ }
+
+ mreq = next_request(mep);
+ if (value) {
+ /*
+ * If there is not request for TX-EP, QMU will not transfer
+ * data to TX-FIFO, so no need check whether TX-FIFO
+ * holds bytes or not here
+ */
+ if (mreq) {
+ dev_dbg(mtu->dev, "req in progress, cannot halt %s\n",
+ ep->name);
+ ret = -EAGAIN;
+ goto done;
+ }
+ } else {
+ mep->flags &= ~MTU3_EP_WEDGE;
+ }
+
+ dev_dbg(mtu->dev, "%s %s stall\n", ep->name, value ? "set" : "clear");
+
+ mtu3_ep_stall_set(mep, value);
+
+done:
+ spin_unlock_irqrestore(&mtu->lock, flags);
+
+ return ret;
+}
+
+/* Sets the halt feature with the clear requests ignored */
+static int mtu3_gadget_ep_set_wedge(struct usb_ep *ep)
+{
+ struct mtu3_ep *mep = to_mtu3_ep(ep);
+
+ mep->flags |= MTU3_EP_WEDGE;
+
+ return usb_ep_set_halt(ep);
+}
+
+static const struct usb_ep_ops mtu3_ep_ops = {
+ .enable = mtu3_gadget_ep_enable,
+ .disable = mtu3_gadget_ep_disable,
+ .alloc_request = mtu3_alloc_request,
+ .free_request = mtu3_free_request,
+ .queue = mtu3_gadget_queue,
+ .dequeue = mtu3_gadget_dequeue,
+ .set_halt = mtu3_gadget_ep_set_halt,
+ .set_wedge = mtu3_gadget_ep_set_wedge,
+};
+
+static int mtu3_gadget_get_frame(struct usb_gadget *gadget)
+{
+ struct mtu3 *mtu = gadget_to_mtu3(gadget);
+
+ return (int)mtu3_readl(mtu->mac_base, U3D_USB20_FRAME_NUM);
+}
+
+static int mtu3_gadget_wakeup(struct usb_gadget *gadget)
+{
+ struct mtu3 *mtu = gadget_to_mtu3(gadget);
+ unsigned long flags;
+
+ dev_dbg(mtu->dev, "%s\n", __func__);
+
+ /* remote wakeup feature is not enabled by host */
+ if (!mtu->may_wakeup)
+ return -EOPNOTSUPP;
+
+ spin_lock_irqsave(&mtu->lock, flags);
+ if (mtu->g.speed >= USB_SPEED_SUPER) {
+ mtu3_setbits(mtu->mac_base, U3D_LINK_POWER_CONTROL, UX_EXIT);
+ } else {
+ mtu3_setbits(mtu->mac_base, U3D_POWER_MANAGEMENT, RESUME);
+ spin_unlock_irqrestore(&mtu->lock, flags);
+ mdelay(10);
+ spin_lock_irqsave(&mtu->lock, flags);
+ mtu3_clrbits(mtu->mac_base, U3D_POWER_MANAGEMENT, RESUME);
+ }
+ spin_unlock_irqrestore(&mtu->lock, flags);
+ return 0;
+}
+
+static int mtu3_gadget_set_self_powered(struct usb_gadget *gadget,
+ int is_selfpowered)
+{
+ struct mtu3 *mtu = gadget_to_mtu3(gadget);
+
+ mtu->is_self_powered = !!is_selfpowered;
+ return 0;
+}
+
+static int mtu3_gadget_pullup(struct usb_gadget *gadget, int is_on)
+{
+ struct mtu3 *mtu = gadget_to_mtu3(gadget);
+ unsigned long flags;
+
+ dev_dbg(mtu->dev, "%s (%s) for %sactive device\n", __func__,
+ is_on ? "on" : "off", mtu->is_active ? "" : "in");
+
+ /* we'd rather not pullup unless the device is active. */
+ spin_lock_irqsave(&mtu->lock, flags);
+
+ is_on = !!is_on;
+ if (!mtu->is_active) {
+ /* save it for mtu3_start() to process the request */
+ mtu->softconnect = is_on;
+ } else if (is_on != mtu->softconnect) {
+ mtu->softconnect = is_on;
+ mtu3_dev_on_off(mtu, is_on);
+ }
+
+ spin_unlock_irqrestore(&mtu->lock, flags);
+
+ return 0;
+}
+
+static int mtu3_gadget_start(struct usb_gadget *gadget,
+ struct usb_gadget_driver *driver)
+{
+ struct mtu3 *mtu = gadget_to_mtu3(gadget);
+ unsigned long flags;
+
+ if (mtu->gadget_driver) {
+ dev_err(mtu->dev, "%s is already bound to %s\n",
+ mtu->g.name, mtu->gadget_driver->function);
+ return -EBUSY;
+ }
+
+ dev_dbg(mtu->dev, "bind driver %s\n", driver->function);
+
+ spin_lock_irqsave(&mtu->lock, flags);
+
+ mtu->softconnect = 0;
+ mtu->gadget_driver = driver;
+ mtu3_start(mtu);
+
+ spin_unlock_irqrestore(&mtu->lock, flags);
+
+ return 0;
+}
+
+static void stop_activity(struct mtu3 *mtu)
+{
+ int i;
+
+ mtu->g.speed = USB_SPEED_UNKNOWN;
+
+ /* deactivate the hardware */
+ if (mtu->softconnect) {
+ mtu->softconnect = 0;
+ mtu3_dev_on_off(mtu, 0);
+ }
+
+ /*
+ * killing any outstanding requests will quiesce the driver;
+ * then report disconnect
+ */
+ nuke(mtu->ep0, -ESHUTDOWN);
+ for (i = 1; i < mtu->num_eps; i++) {
+ nuke(mtu->in_eps + i, -ESHUTDOWN);
+ nuke(mtu->out_eps + i, -ESHUTDOWN);
+ }
+}
+
+static int mtu3_gadget_stop(struct usb_gadget *g)
+{
+ struct mtu3 *mtu = gadget_to_mtu3(g);
+ unsigned long flags;
+
+ dev_dbg(mtu->dev, "%s\n", __func__);
+
+ spin_lock_irqsave(&mtu->lock, flags);
+
+ stop_activity(mtu);
+ mtu->gadget_driver = NULL;
+ mtu3_stop(mtu);
+
+ spin_unlock_irqrestore(&mtu->lock, flags);
+
+ return 0;
+}
+
+static void
+mtu3_gadget_set_speed(struct usb_gadget *g, enum usb_device_speed speed)
+{
+ struct mtu3 *mtu = gadget_to_mtu3(g);
+ unsigned long flags;
+
+ dev_dbg(mtu->dev, "%s %d\n", __func__, speed);
+
+ spin_lock_irqsave(&mtu->lock, flags);
+ mtu3_set_speed(mtu, speed);
+ spin_unlock_irqrestore(&mtu->lock, flags);
+}
+
+static const struct usb_gadget_ops mtu3_gadget_ops = {
+ .get_frame = mtu3_gadget_get_frame,
+ .wakeup = mtu3_gadget_wakeup,
+ .set_selfpowered = mtu3_gadget_set_self_powered,
+ .pullup = mtu3_gadget_pullup,
+ .udc_start = mtu3_gadget_start,
+ .udc_stop = mtu3_gadget_stop,
+ .udc_set_speed = mtu3_gadget_set_speed,
+};
+
+static void mtu3_state_reset(struct mtu3 *mtu)
+{
+ mtu->address = 0;
+ mtu->ep0_state = MU3D_EP0_STATE_SETUP;
+ mtu->may_wakeup = 0;
+ mtu->u1_enable = 0;
+ mtu->u2_enable = 0;
+ mtu->delayed_status = false;
+ mtu->test_mode = false;
+}
+
+static void init_hw_ep(struct mtu3 *mtu, struct mtu3_ep *mep,
+ u32 epnum, u32 is_in)
+{
+ mep->epnum = epnum;
+ mep->mtu = mtu;
+ mep->is_in = is_in;
+
+ INIT_LIST_HEAD(&mep->req_list);
+
+ sprintf(mep->name, "ep%d%s", epnum,
+ !epnum ? "" : (is_in ? "in" : "out"));
+
+ mep->ep.name = mep->name;
+ INIT_LIST_HEAD(&mep->ep.ep_list);
+
+ /* initialize maxpacket as SS */
+ if (!epnum) {
+ usb_ep_set_maxpacket_limit(&mep->ep, USB_HS_MAXP);
+ mep->ep.ops = &mtu3_ep0_ops;
+ mtu->g.ep0 = &mep->ep;
+ } else {
+ usb_ep_set_maxpacket_limit(&mep->ep, USB_SS_MAXP);
+ mep->ep.ops = &mtu3_ep_ops;
+ list_add_tail(&mep->ep.ep_list, &mtu->g.ep_list);
+ }
+
+ dev_dbg(mtu->dev, "%s, name=%s, maxp=%d\n", __func__, mep->ep.name,
+ mep->ep.maxpacket);
+}
+
+static void mtu3_gadget_init_eps(struct mtu3 *mtu)
+{
+ u8 epnum;
+
+ /* initialize endpoint list just once */
+ INIT_LIST_HEAD(&mtu->g.ep_list);
+
+ dev_dbg(mtu->dev, "%s num_eps(1 for a pair of tx&rx ep)=%d\n",
+ __func__, mtu->num_eps);
+
+ init_hw_ep(mtu, mtu->ep0, 0, 0);
+ for (epnum = 1; epnum < mtu->num_eps; epnum++) {
+ init_hw_ep(mtu, mtu->in_eps + epnum, epnum, 1);
+ init_hw_ep(mtu, mtu->out_eps + epnum, epnum, 0);
+ }
+}
+
+int mtu3_gadget_setup(struct mtu3 *mtu)
+{
+ mtu->g.ops = &mtu3_gadget_ops;
+ mtu->g.max_speed = mtu->max_speed;
+ mtu->g.speed = USB_SPEED_UNKNOWN;
+ mtu->g.is_dualspeed = 1;
+ mtu->g.name = MTU3_DRIVER_NAME;
+ mtu->is_active = 0;
+ mtu->delayed_status = false;
+
+ mtu3_gadget_init_eps(mtu);
+
+ return usb_add_gadget_udc((struct device *)mtu->dev, &mtu->g);
+}
+
+void mtu3_gadget_cleanup(struct mtu3 *mtu)
+{
+ usb_del_gadget_udc(&mtu->g);
+}
+
+void mtu3_gadget_resume(struct mtu3 *mtu)
+{
+ dev_dbg(mtu->dev, "gadget RESUME\n");
+ if (mtu->gadget_driver && mtu->gadget_driver->resume) {
+ spin_unlock(&mtu->lock);
+ mtu->gadget_driver->resume(&mtu->g);
+ spin_lock(&mtu->lock);
+ }
+}
+
+/* called when SOF packets stop for 3+ msec or enters U3 */
+void mtu3_gadget_suspend(struct mtu3 *mtu)
+{
+ dev_dbg(mtu->dev, "gadget SUSPEND\n");
+ if (mtu->gadget_driver && mtu->gadget_driver->suspend) {
+ spin_unlock(&mtu->lock);
+ mtu->gadget_driver->suspend(&mtu->g);
+ spin_lock(&mtu->lock);
+ }
+}
+
+/* called when VBUS drops below session threshold, and in other cases */
+void mtu3_gadget_disconnect(struct mtu3 *mtu)
+{
+ dev_dbg(mtu->dev, "gadget DISCONNECT\n");
+ if (mtu->gadget_driver && mtu->gadget_driver->disconnect) {
+ spin_unlock(&mtu->lock);
+ mtu->gadget_driver->disconnect(&mtu->g);
+ spin_lock(&mtu->lock);
+ }
+
+ mtu3_state_reset(mtu);
+ usb_gadget_set_state(&mtu->g, USB_STATE_NOTATTACHED);
+}
+
+void mtu3_gadget_reset(struct mtu3 *mtu)
+{
+ dev_dbg(mtu->dev, "gadget RESET\n");
+
+ /* report disconnect, if we didn't flush EP state */
+ if (mtu->g.speed != USB_SPEED_UNKNOWN)
+ mtu3_gadget_disconnect(mtu);
+ else
+ mtu3_state_reset(mtu);
+}
diff --git a/drivers/usb/mtu3/mtu3_gadget_ep0.c b/drivers/usb/mtu3/mtu3_gadget_ep0.c
new file mode 100644
index 0000000..4b0bc5f
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3_gadget_ep0.c
@@ -0,0 +1,933 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * mtu3_gadget_ep0.c - MediaTek USB3 DRD peripheral driver ep0 handling
+ *
+ * Copyright (c) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng.Yun <chunfeng.yun@mediatek.com>
+ */
+
+#include <linux/iopoll.h>
+#include <linux/usb/composite.h>
+
+#include "mtu3.h"
+
+/* ep0 is always mtu3->in_eps[0] */
+#define next_ep0_request(mtu) next_request((mtu)->ep0)
+
+/* for high speed test mode; see USB 2.0 spec 7.1.20 */
+static const u8 mtu3_test_packet[53] = {
+ /* implicit SYNC then DATA0 to start */
+
+ /* JKJKJKJK x9 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ /* JJKKJJKK x8 */
+ 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa,
+ /* JJJJKKKK x8 */
+ 0xee, 0xee, 0xee, 0xee, 0xee, 0xee, 0xee, 0xee,
+ /* JJJJJJJKKKKKKK x8 */
+ 0xfe, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+ /* JJJJJJJK x8 */
+ 0x7f, 0xbf, 0xdf, 0xef, 0xf7, 0xfb, 0xfd,
+ /* JKKKKKKK x10, JK */
+ 0xfc, 0x7e, 0xbf, 0xdf, 0xef, 0xf7, 0xfb, 0xfd, 0x7e,
+ /* implicit CRC16 then EOP to end */
+};
+
+static char *decode_ep0_state(struct mtu3 *mtu)
+{
+ switch (mtu->ep0_state) {
+ case MU3D_EP0_STATE_SETUP:
+ return "SETUP";
+ case MU3D_EP0_STATE_TX:
+ return "IN";
+ case MU3D_EP0_STATE_RX:
+ return "OUT";
+ case MU3D_EP0_STATE_TX_END:
+ return "TX-END";
+ case MU3D_EP0_STATE_STALL:
+ return "STALL";
+ default:
+ return "??";
+ }
+}
+
+static void ep0_req_giveback(struct mtu3 *mtu, struct usb_request *req)
+{
+ mtu3_req_complete(mtu->ep0, req, 0);
+}
+
+static int
+forward_to_driver(struct mtu3 *mtu, const struct usb_ctrlrequest *setup)
+__releases(mtu->lock)
+__acquires(mtu->lock)
+{
+ int ret;
+
+ if (!mtu->gadget_driver)
+ return -EOPNOTSUPP;
+
+ spin_unlock(&mtu->lock);
+ ret = mtu->gadget_driver->setup(&mtu->g, setup);
+ spin_lock(&mtu->lock);
+
+ dev_dbg(mtu->dev, "%s ret %d\n", __func__, ret);
+ return ret;
+}
+
+static inline void writel_rep(volatile void *addr, const void *buffer,
+ unsigned int count)
+{
+ if (count) {
+ const u32 *buf = buffer;
+
+ do {
+ writel(*buf++, addr);
+ } while (--count);
+ }
+}
+
+static inline void readl_rep(const volatile void *addr, void *buffer,
+ unsigned int count)
+{
+ if (count) {
+ u32 *buf = buffer;
+
+ do {
+ u32 x = readl(addr);
+ *buf++ = x;
+ } while (--count);
+ }
+}
+
+static void ep0_write_fifo(struct mtu3_ep *mep, const u8 *src, u16 len)
+{
+ void __iomem *fifo = mep->mtu->mac_base + U3D_FIFO0;
+ u16 index = 0;
+
+ dev_dbg(mep->mtu->dev, "%s: ep%din, len=%d, buf=%p\n",
+ __func__, mep->epnum, len, src);
+
+ if (len >= 4) {
+ writel_rep(fifo, src, len >> 2);
+ index = len & ~0x03;
+ }
+ if (len & 0x02) {
+ writew(*(u16 *)&src[index], fifo);
+ index += 2;
+ }
+ if (len & 0x01)
+ writeb(src[index], fifo);
+}
+
+static void ep0_read_fifo(struct mtu3_ep *mep, u8 *dst, u16 len)
+{
+ void __iomem *fifo = mep->mtu->mac_base + U3D_FIFO0;
+ u32 value;
+ u16 index = 0;
+
+ dev_dbg(mep->mtu->dev, "%s: ep%dout len=%d buf=%p\n",
+ __func__, mep->epnum, len, dst);
+
+ if (len >= 4) {
+ readl_rep(fifo, dst, len >> 2);
+ index = len & ~0x03;
+ }
+ if (len & 0x3) {
+ value = readl(fifo);
+ memcpy(&dst[index], &value, len & 0x3);
+ }
+}
+
+static void ep0_load_test_packet(struct mtu3 *mtu)
+{
+ /*
+ * because the length of test packet is less than max packet of HS ep0,
+ * write it into fifo directly.
+ */
+ ep0_write_fifo(mtu->ep0, mtu3_test_packet, sizeof(mtu3_test_packet));
+}
+
+/*
+ * A. send STALL for setup transfer without data stage:
+ * set SENDSTALL and SETUPPKTRDY at the same time;
+ * B. send STALL for other cases:
+ * set SENDSTALL only.
+ */
+static void ep0_stall_set(struct mtu3_ep *mep0, bool set, u32 pktrdy)
+{
+ struct mtu3 *mtu = mep0->mtu;
+ void __iomem *mbase = mtu->mac_base;
+ u32 csr;
+
+ /* EP0_SENTSTALL is W1C */
+ csr = mtu3_readl(mbase, U3D_EP0CSR) & EP0_W1C_BITS;
+ if (set)
+ csr |= EP0_SENDSTALL | pktrdy;
+ else
+ csr = (csr & ~EP0_SENDSTALL) | EP0_SENTSTALL;
+ mtu3_writel(mtu->mac_base, U3D_EP0CSR, csr);
+
+ mtu->delayed_status = false;
+ mtu->ep0_state = MU3D_EP0_STATE_SETUP;
+
+ dev_dbg(mtu->dev, "ep0: %s STALL, ep0_state: %s\n",
+ set ? "SEND" : "CLEAR", decode_ep0_state(mtu));
+}
+
+static void ep0_do_status_stage(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+ u32 value;
+
+ value = mtu3_readl(mbase, U3D_EP0CSR) & EP0_W1C_BITS;
+ mtu3_writel(mbase, U3D_EP0CSR, value | EP0_SETUPPKTRDY | EP0_DATAEND);
+}
+
+static int ep0_queue(struct mtu3_ep *mep0, struct mtu3_request *mreq);
+
+static void ep0_dummy_complete(struct usb_ep *ep, struct usb_request *req)
+{}
+
+static void ep0_set_sel_complete(struct usb_ep *ep, struct usb_request *req)
+{
+ struct mtu3_request *mreq;
+ struct mtu3 *mtu;
+ struct usb_set_sel_req sel;
+
+ memcpy(&sel, req->buf, sizeof(sel));
+
+ mreq = to_mtu3_request(req);
+ mtu = mreq->mtu;
+ dev_dbg(mtu->dev, "u1sel:%d, u1pel:%d, u2sel:%d, u2pel:%d\n",
+ sel.u1_sel, sel.u1_pel, sel.u2_sel, sel.u2_pel);
+}
+
+/* queue data stage to handle 6 byte SET_SEL request */
+static int ep0_set_sel(struct mtu3 *mtu, struct usb_ctrlrequest *setup)
+{
+ int ret;
+ u16 length = le16_to_cpu(setup->wLength);
+
+ if (unlikely(length != 6)) {
+ dev_err(mtu->dev, "%s wrong wLength:%d\n",
+ __func__, length);
+ return -EINVAL;
+ }
+
+ mtu->ep0_req.mep = mtu->ep0;
+ mtu->ep0_req.request.length = 6;
+ mtu->ep0_req.request.buf = mtu->setup_buf;
+ mtu->ep0_req.request.complete = ep0_set_sel_complete;
+ ret = ep0_queue(mtu->ep0, &mtu->ep0_req);
+
+ return ret < 0 ? ret : 1;
+}
+
+static int
+ep0_get_status(struct mtu3 *mtu, const struct usb_ctrlrequest *setup)
+{
+ struct mtu3_ep *mep = NULL;
+ int handled = 1;
+ u8 result[2] = {0, 0};
+ u8 epnum = 0;
+ int is_in;
+
+ switch (setup->bRequestType & USB_RECIP_MASK) {
+ case USB_RECIP_DEVICE:
+ result[0] = mtu->is_self_powered << USB_DEVICE_SELF_POWERED;
+ result[0] |= mtu->may_wakeup << USB_DEVICE_REMOTE_WAKEUP;
+
+ if (mtu->g.speed >= USB_SPEED_SUPER) {
+ result[0] |= mtu->u1_enable << USB_DEV_STAT_U1_ENABLED;
+ result[0] |= mtu->u2_enable << USB_DEV_STAT_U2_ENABLED;
+ }
+
+ dev_dbg(mtu->dev, "%s result=%x, U1=%x, U2=%x\n", __func__,
+ result[0], mtu->u1_enable, mtu->u2_enable);
+
+ break;
+ case USB_RECIP_INTERFACE:
+ break;
+ case USB_RECIP_ENDPOINT:
+ epnum = (u8)le16_to_cpu(setup->wIndex);
+ is_in = epnum & USB_DIR_IN;
+ epnum &= USB_ENDPOINT_NUMBER_MASK;
+
+ if (epnum >= mtu->num_eps) {
+ handled = -EINVAL;
+ break;
+ }
+ if (!epnum)
+ break;
+
+ mep = (is_in ? mtu->in_eps : mtu->out_eps) + epnum;
+ if (!mep->desc) {
+ handled = -EINVAL;
+ break;
+ }
+ if (mep->flags & MTU3_EP_STALL)
+ result[0] |= 1 << USB_ENDPOINT_HALT;
+
+ break;
+ default:
+ /* class, vendor, etc ... delegate */
+ handled = 0;
+ break;
+ }
+
+ if (handled > 0) {
+ int ret;
+
+ /* prepare a data stage for GET_STATUS */
+ dev_dbg(mtu->dev, "get_status=%x\n", *(u16 *)result);
+ memcpy(mtu->setup_buf, result, sizeof(result));
+ mtu->ep0_req.mep = mtu->ep0;
+ mtu->ep0_req.request.length = 2;
+ mtu->ep0_req.request.buf = &mtu->setup_buf;
+ mtu->ep0_req.request.complete = ep0_dummy_complete;
+ ret = ep0_queue(mtu->ep0, &mtu->ep0_req);
+ if (ret < 0)
+ handled = ret;
+ }
+ return handled;
+}
+
+static int handle_test_mode(struct mtu3 *mtu, struct usb_ctrlrequest *setup)
+{
+ void __iomem *mbase = mtu->mac_base;
+ int handled = 1;
+ u32 value = 0;
+
+ switch (le16_to_cpu(setup->wIndex) >> 8) {
+ case TEST_J:
+ dev_dbg(mtu->dev, "TEST_J\n");
+ mtu->test_mode_nr = TEST_J_MODE;
+ break;
+ case TEST_K:
+ dev_dbg(mtu->dev, "TEST_K\n");
+ mtu->test_mode_nr = TEST_K_MODE;
+ break;
+ case TEST_SE0_NAK:
+ dev_dbg(mtu->dev, "TEST_SE0_NAK\n");
+ mtu->test_mode_nr = TEST_SE0_NAK_MODE;
+ break;
+ case TEST_PACKET:
+ dev_dbg(mtu->dev, "TEST_PACKET\n");
+ mtu->test_mode_nr = TEST_PACKET_MODE;
+ break;
+ default:
+ handled = -EINVAL;
+ goto out;
+ }
+
+ mtu->test_mode = true;
+
+ /* no TX completion interrupt, and need restart platform after test */
+ if (mtu->test_mode_nr == TEST_PACKET_MODE)
+ ep0_load_test_packet(mtu);
+
+ /* send status before entering test mode. */
+ ep0_do_status_stage(mtu);
+
+ /* wait for ACK status sent by host */
+ readl_poll_timeout(mbase + U3D_EP0CSR, value,
+ !(value & EP0_DATAEND), 5000);
+
+ mtu3_writel(mbase, U3D_USB2_TEST_MODE, mtu->test_mode_nr);
+
+ mtu->ep0_state = MU3D_EP0_STATE_SETUP;
+
+out:
+ return handled;
+}
+
+static int ep0_handle_feature_dev(struct mtu3 *mtu,
+ struct usb_ctrlrequest *setup, bool set)
+{
+ void __iomem *mbase = mtu->mac_base;
+ int handled = -EINVAL;
+ u32 lpc;
+
+ switch (le16_to_cpu(setup->wValue)) {
+ case USB_DEVICE_REMOTE_WAKEUP:
+ mtu->may_wakeup = !!set;
+ handled = 1;
+ break;
+ case USB_DEVICE_TEST_MODE:
+ if (!set || (mtu->g.speed != USB_SPEED_HIGH) ||
+ (le16_to_cpu(setup->wIndex) & 0xff))
+ break;
+
+ handled = handle_test_mode(mtu, setup);
+ break;
+ case USB_DEVICE_U1_ENABLE:
+ if (mtu->g.speed < USB_SPEED_SUPER ||
+ mtu->g.state != USB_STATE_CONFIGURED)
+ break;
+
+ lpc = mtu3_readl(mbase, U3D_LINK_POWER_CONTROL);
+ if (set)
+ lpc |= SW_U1_REQUEST_ENABLE;
+ else
+ lpc &= ~SW_U1_REQUEST_ENABLE;
+ mtu3_writel(mbase, U3D_LINK_POWER_CONTROL, lpc);
+
+ mtu->u1_enable = !!set;
+ handled = 1;
+ break;
+ case USB_DEVICE_U2_ENABLE:
+ if (mtu->g.speed < USB_SPEED_SUPER ||
+ mtu->g.state != USB_STATE_CONFIGURED)
+ break;
+
+ lpc = mtu3_readl(mbase, U3D_LINK_POWER_CONTROL);
+ if (set)
+ lpc |= SW_U2_REQUEST_ENABLE;
+ else
+ lpc &= ~SW_U2_REQUEST_ENABLE;
+ mtu3_writel(mbase, U3D_LINK_POWER_CONTROL, lpc);
+
+ mtu->u2_enable = !!set;
+ handled = 1;
+ break;
+ default:
+ handled = -EINVAL;
+ break;
+ }
+ return handled;
+}
+
+static int ep0_handle_feature(struct mtu3 *mtu,
+ struct usb_ctrlrequest *setup, bool set)
+{
+ struct mtu3_ep *mep;
+ int handled = -EINVAL;
+ int is_in;
+ u16 value;
+ u16 index;
+ u8 epnum;
+
+ value = le16_to_cpu(setup->wValue);
+ index = le16_to_cpu(setup->wIndex);
+
+ switch (setup->bRequestType & USB_RECIP_MASK) {
+ case USB_RECIP_DEVICE:
+ handled = ep0_handle_feature_dev(mtu, setup, set);
+ break;
+ case USB_RECIP_INTERFACE:
+ /* superspeed only */
+ if (value == USB_INTRF_FUNC_SUSPEND &&
+ mtu->g.speed >= USB_SPEED_SUPER) {
+ /*
+ * forward the request because function drivers
+ * should handle it
+ */
+ handled = 0;
+ }
+ break;
+ case USB_RECIP_ENDPOINT:
+ epnum = index & USB_ENDPOINT_NUMBER_MASK;
+ if (epnum == 0 || epnum >= mtu->num_eps ||
+ value != USB_ENDPOINT_HALT)
+ break;
+
+ is_in = index & USB_DIR_IN;
+ mep = (is_in ? mtu->in_eps : mtu->out_eps) + epnum;
+ if (!mep->desc)
+ break;
+
+ handled = 1;
+ /* ignore request if endpoint is wedged */
+ if (mep->flags & MTU3_EP_WEDGE)
+ break;
+
+ mtu3_ep_stall_set(mep, set);
+ break;
+ default:
+ /* class, vendor, etc ... delegate */
+ handled = 0;
+ break;
+ }
+ return handled;
+}
+
+/*
+ * handle all control requests can be handled
+ * returns:
+ * negative errno - error happened
+ * zero - need delegate SETUP to gadget driver
+ * positive - already handled
+ */
+static int handle_standard_request(struct mtu3 *mtu,
+ struct usb_ctrlrequest *setup)
+{
+ void __iomem *mbase = mtu->mac_base;
+ enum usb_device_state state = mtu->g.state;
+ int handled = -EINVAL;
+ u32 dev_conf;
+ u16 value;
+
+ value = le16_to_cpu(setup->wValue);
+
+ /* the gadget driver handles everything except what we must handle */
+ switch (setup->bRequest) {
+ case USB_REQ_SET_ADDRESS:
+ /* change it after the status stage */
+ mtu->address = (u8)(value & 0x7f);
+ dev_dbg(mtu->dev, "set address to 0x%x\n", mtu->address);
+
+ dev_conf = mtu3_readl(mbase, U3D_DEVICE_CONF);
+ dev_conf &= ~DEV_ADDR_MSK;
+ dev_conf |= DEV_ADDR(mtu->address);
+ mtu3_writel(mbase, U3D_DEVICE_CONF, dev_conf);
+
+ if (mtu->address)
+ usb_gadget_set_state(&mtu->g, USB_STATE_ADDRESS);
+ else
+ usb_gadget_set_state(&mtu->g, USB_STATE_DEFAULT);
+
+ handled = 1;
+ break;
+ case USB_REQ_SET_CONFIGURATION:
+ if (state == USB_STATE_ADDRESS) {
+ usb_gadget_set_state(&mtu->g,
+ USB_STATE_CONFIGURED);
+ } else if (state == USB_STATE_CONFIGURED) {
+ /*
+ * USB2 spec sec 9.4.7, if wValue is 0 then dev
+ * is moved to addressed state
+ */
+ if (!value)
+ usb_gadget_set_state(&mtu->g,
+ USB_STATE_ADDRESS);
+ }
+ handled = 0;
+ break;
+ case USB_REQ_CLEAR_FEATURE:
+ handled = ep0_handle_feature(mtu, setup, 0);
+ break;
+ case USB_REQ_SET_FEATURE:
+ handled = ep0_handle_feature(mtu, setup, 1);
+ break;
+ case USB_REQ_GET_STATUS:
+ handled = ep0_get_status(mtu, setup);
+ break;
+ case USB_REQ_SET_SEL:
+ handled = ep0_set_sel(mtu, setup);
+ break;
+ case USB_REQ_SET_ISOCH_DELAY:
+ handled = 1;
+ break;
+ default:
+ /* delegate SET_CONFIGURATION, etc */
+ handled = 0;
+ }
+
+ return handled;
+}
+
+/* receive an data packet (OUT) */
+static void ep0_rx_state(struct mtu3 *mtu)
+{
+ struct mtu3_request *mreq;
+ struct usb_request *req;
+ void __iomem *mbase = mtu->mac_base;
+ u32 maxp;
+ u32 csr;
+ u16 count = 0;
+
+ dev_dbg(mtu->dev, "%s\n", __func__);
+
+ csr = mtu3_readl(mbase, U3D_EP0CSR) & EP0_W1C_BITS;
+ mreq = next_ep0_request(mtu);
+ req = &mreq->request;
+
+ /* read packet and ack; or stall because of gadget driver bug */
+ if (req) {
+ void *buf = req->buf + req->actual;
+ unsigned int len = req->length - req->actual;
+
+ /* read the buffer */
+ count = mtu3_readl(mbase, U3D_RXCOUNT0);
+ if (count > len) {
+ req->status = -EOVERFLOW;
+ count = len;
+ }
+ ep0_read_fifo(mtu->ep0, buf, count);
+ req->actual += count;
+ csr |= EP0_RXPKTRDY;
+
+ maxp = mtu->g.ep0->maxpacket;
+ if (count < maxp || req->actual == req->length) {
+ mtu->ep0_state = MU3D_EP0_STATE_SETUP;
+ dev_dbg(mtu->dev, "ep0 state: %s\n",
+ decode_ep0_state(mtu));
+
+ csr |= EP0_DATAEND;
+ } else {
+ req = NULL;
+ }
+ } else {
+ csr |= EP0_RXPKTRDY | EP0_SENDSTALL;
+ dev_dbg(mtu->dev, "%s: SENDSTALL\n", __func__);
+ }
+
+ mtu3_writel(mbase, U3D_EP0CSR, csr);
+
+ /* give back the request if have received all data */
+ if (req)
+ ep0_req_giveback(mtu, req);
+}
+
+/* transmitting to the host (IN) */
+static void ep0_tx_state(struct mtu3 *mtu)
+{
+ struct mtu3_request *mreq = next_ep0_request(mtu);
+ struct usb_request *req;
+ u32 csr;
+ u8 *src;
+ u32 count;
+ u32 maxp;
+
+ dev_dbg(mtu->dev, "%s\n", __func__);
+
+ if (!mreq)
+ return;
+
+ maxp = mtu->g.ep0->maxpacket;
+ req = &mreq->request;
+
+ /* load the data */
+ src = (u8 *)req->buf + req->actual;
+ count = min(maxp, req->length - req->actual);
+ if (count)
+ ep0_write_fifo(mtu->ep0, src, count);
+
+ dev_dbg(mtu->dev, "%s act=%d, len=%d, cnt=%d, maxp=%d zero=%d\n",
+ __func__, req->actual, req->length, count, maxp, req->zero);
+
+ req->actual += count;
+
+ if ((count < maxp) ||
+ ((req->actual == req->length) && !req->zero))
+ mtu->ep0_state = MU3D_EP0_STATE_TX_END;
+
+ /* send it out, triggering a "txpktrdy cleared" irq */
+ csr = mtu3_readl(mtu->mac_base, U3D_EP0CSR) & EP0_W1C_BITS;
+ mtu3_writel(mtu->mac_base, U3D_EP0CSR, csr | EP0_TXPKTRDY);
+
+ dev_dbg(mtu->dev, "%s ep0csr=0x%x\n", __func__,
+ mtu3_readl(mtu->mac_base, U3D_EP0CSR));
+}
+
+static void ep0_read_setup(struct mtu3 *mtu, struct usb_ctrlrequest *setup)
+{
+ struct mtu3_request *mreq;
+ u32 count;
+ u32 csr;
+
+ csr = mtu3_readl(mtu->mac_base, U3D_EP0CSR) & EP0_W1C_BITS;
+ count = mtu3_readl(mtu->mac_base, U3D_RXCOUNT0);
+
+ ep0_read_fifo(mtu->ep0, (u8 *)setup, count);
+
+ dev_dbg(mtu->dev, "SETUP req%02x.%02x v%04x i%04x l%04x\n",
+ setup->bRequestType, setup->bRequest,
+ le16_to_cpu(setup->wValue), le16_to_cpu(setup->wIndex),
+ le16_to_cpu(setup->wLength));
+
+ /* clean up any leftover transfers */
+ mreq = next_ep0_request(mtu);
+ if (mreq)
+ ep0_req_giveback(mtu, &mreq->request);
+
+ if (le16_to_cpu(setup->wLength) == 0) {
+ ; /* no data stage, nothing to do */
+ } else if (setup->bRequestType & USB_DIR_IN) {
+ mtu3_writel(mtu->mac_base, U3D_EP0CSR,
+ csr | EP0_SETUPPKTRDY | EP0_DPHTX);
+ mtu->ep0_state = MU3D_EP0_STATE_TX;
+ } else {
+ mtu3_writel(mtu->mac_base, U3D_EP0CSR,
+ (csr | EP0_SETUPPKTRDY) & (~EP0_DPHTX));
+ mtu->ep0_state = MU3D_EP0_STATE_RX;
+ }
+}
+
+static int ep0_handle_setup(struct mtu3 *mtu)
+__releases(mtu->lock)
+__acquires(mtu->lock)
+{
+ struct usb_ctrlrequest setup;
+ struct mtu3_request *mreq;
+ int handled = 0;
+
+ ep0_read_setup(mtu, &setup);
+
+ if ((setup.bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD)
+ handled = handle_standard_request(mtu, &setup);
+
+ dev_dbg(mtu->dev, "handled %d, ep0_state: %s\n",
+ handled, decode_ep0_state(mtu));
+
+ if (handled < 0)
+ goto stall;
+ else if (handled > 0)
+ goto finish;
+
+ handled = forward_to_driver(mtu, &setup);
+ if (handled < 0) {
+stall:
+ dev_dbg(mtu->dev, "%s stall (%d)\n", __func__, handled);
+
+ ep0_stall_set(mtu->ep0, true,
+ le16_to_cpu(setup.wLength) ? 0 : EP0_SETUPPKTRDY);
+
+ return 0;
+ }
+
+finish:
+ if (mtu->test_mode) {
+ ; /* nothing to do */
+ } else if (handled == USB_GADGET_DELAYED_STATUS) {
+
+ mreq = next_ep0_request(mtu);
+ if (mreq) {
+ /* already asked us to continue delayed status */
+ ep0_do_status_stage(mtu);
+ ep0_req_giveback(mtu, &mreq->request);
+ } else {
+ /* do delayed STATUS stage till receive ep0_queue */
+ mtu->delayed_status = true;
+ }
+ } else if (le16_to_cpu(setup.wLength) == 0) { /* no data stage */
+
+ ep0_do_status_stage(mtu);
+ /* complete zlp request directly */
+ mreq = next_ep0_request(mtu);
+ if (mreq && !mreq->request.length)
+ ep0_req_giveback(mtu, &mreq->request);
+ }
+
+ return 0;
+}
+
+irqreturn_t mtu3_ep0_isr(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+ struct mtu3_request *mreq;
+ u32 int_status;
+ irqreturn_t ret = IRQ_NONE;
+ u32 csr;
+ u32 len;
+
+ int_status = mtu3_readl(mbase, U3D_EPISR);
+ int_status &= mtu3_readl(mbase, U3D_EPIER);
+ mtu3_writel(mbase, U3D_EPISR, int_status); /* W1C */
+
+ /* only handle ep0's */
+ if (!(int_status & (EP0ISR | SETUPENDISR)))
+ return IRQ_NONE;
+
+ /* abort current SETUP, and process new one */
+ if (int_status & SETUPENDISR)
+ mtu->ep0_state = MU3D_EP0_STATE_SETUP;
+
+ csr = mtu3_readl(mbase, U3D_EP0CSR);
+
+ dev_dbg(mtu->dev, "%s csr=0x%x\n", __func__, csr);
+
+ /* we sent a stall.. need to clear it now.. */
+ if (csr & EP0_SENTSTALL) {
+ ep0_stall_set(mtu->ep0, false, 0);
+ csr = mtu3_readl(mbase, U3D_EP0CSR);
+ ret = IRQ_HANDLED;
+ }
+ dev_dbg(mtu->dev, "ep0_state: %s\n", decode_ep0_state(mtu));
+
+ switch (mtu->ep0_state) {
+ case MU3D_EP0_STATE_TX:
+ /* irq on clearing txpktrdy */
+ if ((csr & EP0_FIFOFULL) == 0) {
+ ep0_tx_state(mtu);
+ ret = IRQ_HANDLED;
+ }
+ break;
+ case MU3D_EP0_STATE_RX:
+ /* irq on set rxpktrdy */
+ if (csr & EP0_RXPKTRDY) {
+ ep0_rx_state(mtu);
+ ret = IRQ_HANDLED;
+ }
+ break;
+ case MU3D_EP0_STATE_TX_END:
+ mtu3_writel(mbase, U3D_EP0CSR,
+ (csr & EP0_W1C_BITS) | EP0_DATAEND);
+
+ mreq = next_ep0_request(mtu);
+ if (mreq)
+ ep0_req_giveback(mtu, &mreq->request);
+
+ mtu->ep0_state = MU3D_EP0_STATE_SETUP;
+ ret = IRQ_HANDLED;
+ dev_dbg(mtu->dev, "ep0_state: %s\n", decode_ep0_state(mtu));
+ break;
+ case MU3D_EP0_STATE_SETUP:
+ if (!(csr & EP0_SETUPPKTRDY))
+ break;
+
+ len = mtu3_readl(mbase, U3D_RXCOUNT0);
+ if (len != 8) {
+ dev_err(mtu->dev, "SETUP packet len %d != 8 ?\n", len);
+ break;
+ }
+
+ ep0_handle_setup(mtu);
+ ret = IRQ_HANDLED;
+ break;
+ default:
+ /* can't happen */
+ ep0_stall_set(mtu->ep0, true, 0);
+ WARN_ON(1);
+ break;
+ }
+
+ return ret;
+}
+
+static int mtu3_ep0_enable(struct usb_ep *ep,
+ const struct usb_endpoint_descriptor *desc)
+{
+ /* always enabled */
+ return -EINVAL;
+}
+
+static int mtu3_ep0_disable(struct usb_ep *ep)
+{
+ /* always enabled */
+ return -EINVAL;
+}
+
+static int ep0_queue(struct mtu3_ep *mep, struct mtu3_request *mreq)
+{
+ struct mtu3 *mtu = mep->mtu;
+
+ mreq->mtu = mtu;
+ mreq->request.actual = 0;
+ mreq->request.status = -EINPROGRESS;
+
+ dev_dbg(mtu->dev, "%s %s (ep0_state: %s), len#%d\n", __func__,
+ mep->name, decode_ep0_state(mtu), mreq->request.length);
+
+ switch (mtu->ep0_state) {
+ case MU3D_EP0_STATE_SETUP:
+ case MU3D_EP0_STATE_RX: /* control-OUT data */
+ case MU3D_EP0_STATE_TX: /* control-IN data */
+ break;
+ default:
+ dev_err(mtu->dev, "%s, error in ep0 state %s\n", __func__,
+ decode_ep0_state(mtu));
+ return -EINVAL;
+ }
+
+ if (mtu->delayed_status) {
+ mtu->delayed_status = false;
+ ep0_do_status_stage(mtu);
+ /* needn't giveback the request for handling delay STATUS */
+ return 0;
+ }
+
+ if (!list_empty(&mep->req_list))
+ return -EBUSY;
+
+ list_add_tail(&mreq->list, &mep->req_list);
+
+ /* sequence #1, IN ... start writing the data */
+ if (mtu->ep0_state == MU3D_EP0_STATE_TX)
+ ep0_tx_state(mtu);
+
+ return 0;
+}
+
+static int mtu3_ep0_queue(struct usb_ep *ep,
+ struct usb_request *req, gfp_t gfp)
+{
+ struct mtu3_ep *mep;
+ struct mtu3_request *mreq;
+ struct mtu3 *mtu;
+ unsigned long flags;
+ int ret = 0;
+
+ if (!ep || !req)
+ return -EINVAL;
+
+ mep = to_mtu3_ep(ep);
+ mtu = mep->mtu;
+ mreq = to_mtu3_request(req);
+
+ spin_lock_irqsave(&mtu->lock, flags);
+ ret = ep0_queue(mep, mreq);
+ spin_unlock_irqrestore(&mtu->lock, flags);
+ return ret;
+}
+
+static int mtu3_ep0_dequeue(struct usb_ep *ep, struct usb_request *req)
+{
+ /* we just won't support this */
+ return -EINVAL;
+}
+
+static int mtu3_ep0_halt(struct usb_ep *ep, int value)
+{
+ struct mtu3_ep *mep;
+ struct mtu3 *mtu;
+ unsigned long flags;
+ int ret = 0;
+
+ if (!ep || !value)
+ return -EINVAL;
+
+ mep = to_mtu3_ep(ep);
+ mtu = mep->mtu;
+
+ dev_dbg(mtu->dev, "%s\n", __func__);
+
+ spin_lock_irqsave(&mtu->lock, flags);
+
+ if (!list_empty(&mep->req_list)) {
+ ret = -EBUSY;
+ goto cleanup;
+ }
+
+ switch (mtu->ep0_state) {
+ /*
+ * stalls are usually issued after parsing SETUP packet, either
+ * directly in irq context from setup() or else later.
+ */
+ case MU3D_EP0_STATE_TX:
+ case MU3D_EP0_STATE_TX_END:
+ case MU3D_EP0_STATE_RX:
+ case MU3D_EP0_STATE_SETUP:
+ ep0_stall_set(mtu->ep0, true, 0);
+ break;
+ default:
+ dev_dbg(mtu->dev, "ep0 can't halt in state %s\n",
+ decode_ep0_state(mtu));
+ ret = -EINVAL;
+ }
+
+cleanup:
+ spin_unlock_irqrestore(&mtu->lock, flags);
+ return ret;
+}
+
+const struct usb_ep_ops mtu3_ep0_ops = {
+ .enable = mtu3_ep0_enable,
+ .disable = mtu3_ep0_disable,
+ .alloc_request = mtu3_alloc_request,
+ .free_request = mtu3_free_request,
+ .queue = mtu3_ep0_queue,
+ .dequeue = mtu3_ep0_dequeue,
+ .set_halt = mtu3_ep0_halt,
+};
diff --git a/drivers/usb/mtu3/mtu3_host.c b/drivers/usb/mtu3/mtu3_host.c
new file mode 100644
index 0000000..8001fc2
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3_host.c
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * mtu3_dr.c - dual role switch and host glue layer
+ *
+ * Copyright (C) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+#include <dm/lists.h>
+#include <linux/iopoll.h>
+
+#include "mtu3.h"
+#include "mtu3_dr.h"
+
+static void host_ports_num_get(struct mtu3_host *u3h)
+{
+ u32 xhci_cap;
+
+ xhci_cap = mtu3_readl(u3h->ippc_base, U3D_SSUSB_IP_XHCI_CAP);
+ u3h->u2_ports = SSUSB_IP_XHCI_U2_PORT_NUM(xhci_cap);
+ u3h->u3_ports = SSUSB_IP_XHCI_U3_PORT_NUM(xhci_cap);
+
+ dev_dbg(u3h->dev, "host - u2_ports:%d, u3_ports:%d\n",
+ u3h->u2_ports, u3h->u3_ports);
+}
+
+/* only configure ports will be used later */
+static int ssusb_host_enable(struct mtu3_host *u3h)
+{
+ void __iomem *ibase = u3h->ippc_base;
+ int num_u3p = u3h->u3_ports;
+ int num_u2p = u3h->u2_ports;
+ int u3_ports_disabed;
+ u32 check_clk;
+ u32 value;
+ int i;
+
+ /* power on host ip */
+ mtu3_clrbits(ibase, U3D_SSUSB_IP_PW_CTRL1, SSUSB_IP_HOST_PDN);
+
+ /* power on and enable u3 ports except skipped ones */
+ u3_ports_disabed = 0;
+ for (i = 0; i < num_u3p; i++) {
+ if ((0x1 << i) & u3h->u3p_dis_msk) {
+ u3_ports_disabed++;
+ continue;
+ }
+
+ value = mtu3_readl(ibase, SSUSB_U3_CTRL(i));
+ value &= ~(SSUSB_U3_PORT_PDN | SSUSB_U3_PORT_DIS);
+ value |= SSUSB_U3_PORT_HOST_SEL;
+ mtu3_writel(ibase, SSUSB_U3_CTRL(i), value);
+ }
+
+ /* power on and enable all u2 ports */
+ for (i = 0; i < num_u2p; i++) {
+ value = mtu3_readl(ibase, SSUSB_U2_CTRL(i));
+ value &= ~(SSUSB_U2_PORT_PDN | SSUSB_U2_PORT_DIS);
+ value |= SSUSB_U2_PORT_HOST_SEL;
+ mtu3_writel(ibase, SSUSB_U2_CTRL(i), value);
+ }
+
+ check_clk = SSUSB_XHCI_RST_B_STS;
+ if (num_u3p > u3_ports_disabed)
+ check_clk = SSUSB_U3_MAC_RST_B_STS;
+
+ return ssusb_check_clocks(u3h->ssusb, check_clk);
+}
+
+static void ssusb_host_disable(struct mtu3_host *u3h)
+{
+ void __iomem *ibase = u3h->ippc_base;
+ int num_u3p = u3h->u3_ports;
+ int num_u2p = u3h->u2_ports;
+ u32 value;
+ int i;
+
+ /* power down and disable u3 ports except skipped ones */
+ for (i = 0; i < num_u3p; i++) {
+ if ((0x1 << i) & u3h->u3p_dis_msk)
+ continue;
+
+ value = mtu3_readl(ibase, SSUSB_U3_CTRL(i));
+ value |= SSUSB_U3_PORT_PDN | SSUSB_U3_PORT_DIS;
+ mtu3_writel(ibase, SSUSB_U3_CTRL(i), value);
+ }
+
+ /* power down and disable all u2 ports */
+ for (i = 0; i < num_u2p; i++) {
+ value = mtu3_readl(ibase, SSUSB_U2_CTRL(i));
+ value |= SSUSB_U2_PORT_PDN | SSUSB_U2_PORT_DIS;
+ mtu3_writel(ibase, SSUSB_U2_CTRL(i), value);
+ }
+
+ /* power down host ip */
+ mtu3_setbits(ibase, U3D_SSUSB_IP_PW_CTRL1, SSUSB_IP_HOST_PDN);
+}
+
+/*
+ * If host supports multiple ports, the VBUSes(5V) of ports except port0
+ * which supports OTG are better to be enabled by default in DTS.
+ * Because the host driver will keep link with devices attached when system
+ * enters suspend mode, so no need to control VBUSes after initialization.
+ */
+int ssusb_host_init(struct ssusb_mtk *ssusb)
+{
+ struct mtu3_host *u3h = ssusb->u3h;
+ struct udevice *dev = u3h->dev;
+ int ret;
+
+ u3h->ssusb = ssusb;
+ u3h->hcd = ssusb->mac_base;
+ u3h->ippc_base = ssusb->ippc_base;
+
+ /* optional property, ignore the error */
+ dev_read_u32(dev, "mediatek,u3p-dis-msk", &u3h->u3p_dis_msk);
+
+ host_ports_num_get(u3h);
+ ret = ssusb_host_enable(u3h);
+ if (ret)
+ return ret;
+
+ ssusb_set_force_mode(ssusb, MTU3_DR_FORCE_HOST);
+
+ ret = regulator_set_enable(ssusb->vbus_supply, true);
+ if (ret < 0 && ret != -ENOSYS) {
+ dev_err(dev, "failed to enable vbus %d!\n", ret);
+ return ret;
+ }
+
+ dev_info(dev, "%s done...\n", __func__);
+
+ return 0;
+}
+
+void ssusb_host_exit(struct ssusb_mtk *ssusb)
+{
+ regulator_set_enable(ssusb->vbus_supply, false);
+ ssusb_host_disable(ssusb->u3h);
+}
diff --git a/drivers/usb/mtu3/mtu3_hw_regs.h b/drivers/usb/mtu3/mtu3_hw_regs.h
new file mode 100644
index 0000000..9c2a7e1
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3_hw_regs.h
@@ -0,0 +1,515 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * mtu3_hw_regs.h - MediaTek USB3 DRD register and field definitions
+ *
+ * Copyright (C) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+#ifndef _SSUSB_HW_REGS_H_
+#define _SSUSB_HW_REGS_H_
+
+/* segment offset of MAC register */
+#define SSUSB_XCHI_BASE 0x0000
+#define SSUSB_DEV_BASE 0x1000
+#define SSUSB_EPCTL_CSR_BASE 0x1800
+#define SSUSB_USB3_MAC_CSR_BASE 0x2400
+#define SSUSB_USB3_SYS_CSR_BASE 0x2400
+#define SSUSB_USB2_CSR_BASE 0x3400
+
+/* IPPC register in Infra */
+#define SSUSB_SIFSLV_IPPC_BASE 0x0000
+
+/* --------------- SSUSB_DEV REGISTER DEFINITION --------------- */
+
+#define U3D_LV1ISR (SSUSB_DEV_BASE + 0x0000)
+#define U3D_LV1IER (SSUSB_DEV_BASE + 0x0004)
+#define U3D_LV1IESR (SSUSB_DEV_BASE + 0x0008)
+#define U3D_LV1IECR (SSUSB_DEV_BASE + 0x000C)
+
+#define U3D_EPISR (SSUSB_DEV_BASE + 0x0080)
+#define U3D_EPIER (SSUSB_DEV_BASE + 0x0084)
+#define U3D_EPIESR (SSUSB_DEV_BASE + 0x0088)
+#define U3D_EPIECR (SSUSB_DEV_BASE + 0x008C)
+
+#define U3D_EP0CSR (SSUSB_DEV_BASE + 0x0100)
+#define U3D_RXCOUNT0 (SSUSB_DEV_BASE + 0x0108)
+#define U3D_RESERVED (SSUSB_DEV_BASE + 0x010C)
+#define U3D_TX1CSR0 (SSUSB_DEV_BASE + 0x0110)
+#define U3D_TX1CSR1 (SSUSB_DEV_BASE + 0x0114)
+#define U3D_TX1CSR2 (SSUSB_DEV_BASE + 0x0118)
+
+#define U3D_RX1CSR0 (SSUSB_DEV_BASE + 0x0210)
+#define U3D_RX1CSR1 (SSUSB_DEV_BASE + 0x0214)
+#define U3D_RX1CSR2 (SSUSB_DEV_BASE + 0x0218)
+
+#define U3D_FIFO0 (SSUSB_DEV_BASE + 0x0300)
+
+#define U3D_QCR0 (SSUSB_DEV_BASE + 0x0400)
+#define U3D_QCR1 (SSUSB_DEV_BASE + 0x0404)
+#define U3D_QCR2 (SSUSB_DEV_BASE + 0x0408)
+#define U3D_QCR3 (SSUSB_DEV_BASE + 0x040C)
+#define U3D_QFCR (SSUSB_DEV_BASE + 0x0428)
+
+#define U3D_TXQCSR1 (SSUSB_DEV_BASE + 0x0510)
+#define U3D_TXQSAR1 (SSUSB_DEV_BASE + 0x0514)
+#define U3D_TXQCPR1 (SSUSB_DEV_BASE + 0x0518)
+
+#define U3D_RXQCSR1 (SSUSB_DEV_BASE + 0x0610)
+#define U3D_RXQSAR1 (SSUSB_DEV_BASE + 0x0614)
+#define U3D_RXQCPR1 (SSUSB_DEV_BASE + 0x0618)
+#define U3D_RXQLDPR1 (SSUSB_DEV_BASE + 0x061C)
+
+#define U3D_QISAR0 (SSUSB_DEV_BASE + 0x0700)
+#define U3D_QIER0 (SSUSB_DEV_BASE + 0x0704)
+#define U3D_QIESR0 (SSUSB_DEV_BASE + 0x0708)
+#define U3D_QIECR0 (SSUSB_DEV_BASE + 0x070C)
+#define U3D_QISAR1 (SSUSB_DEV_BASE + 0x0710)
+#define U3D_QIER1 (SSUSB_DEV_BASE + 0x0714)
+#define U3D_QIESR1 (SSUSB_DEV_BASE + 0x0718)
+#define U3D_QIECR1 (SSUSB_DEV_BASE + 0x071C)
+
+#define U3D_TQERRIR0 (SSUSB_DEV_BASE + 0x0780)
+#define U3D_TQERRIER0 (SSUSB_DEV_BASE + 0x0784)
+#define U3D_TQERRIESR0 (SSUSB_DEV_BASE + 0x0788)
+#define U3D_TQERRIECR0 (SSUSB_DEV_BASE + 0x078C)
+#define U3D_RQERRIR0 (SSUSB_DEV_BASE + 0x07C0)
+#define U3D_RQERRIER0 (SSUSB_DEV_BASE + 0x07C4)
+#define U3D_RQERRIESR0 (SSUSB_DEV_BASE + 0x07C8)
+#define U3D_RQERRIECR0 (SSUSB_DEV_BASE + 0x07CC)
+#define U3D_RQERRIR1 (SSUSB_DEV_BASE + 0x07D0)
+#define U3D_RQERRIER1 (SSUSB_DEV_BASE + 0x07D4)
+#define U3D_RQERRIESR1 (SSUSB_DEV_BASE + 0x07D8)
+#define U3D_RQERRIECR1 (SSUSB_DEV_BASE + 0x07DC)
+
+#define U3D_CAP_EP0FFSZ (SSUSB_DEV_BASE + 0x0C04)
+#define U3D_CAP_EPNTXFFSZ (SSUSB_DEV_BASE + 0x0C08)
+#define U3D_CAP_EPNRXFFSZ (SSUSB_DEV_BASE + 0x0C0C)
+#define U3D_CAP_EPINFO (SSUSB_DEV_BASE + 0x0C10)
+#define U3D_MISC_CTRL (SSUSB_DEV_BASE + 0x0C84)
+
+/*---------------- SSUSB_DEV FIELD DEFINITION ---------------*/
+
+/* U3D_LV1ISR */
+#define EP_CTRL_INTR BIT(5)
+#define MAC2_INTR BIT(4)
+#define DMA_INTR BIT(3)
+#define MAC3_INTR BIT(2)
+#define QMU_INTR BIT(1)
+#define BMU_INTR BIT(0)
+
+/* U3D_LV1IECR */
+#define LV1IECR_MSK GENMASK(31, 0)
+
+/* U3D_EPISR */
+#define EPRISR(x) (BIT(16) << (x))
+#define SETUPENDISR BIT(16)
+#define EPTISR(x) (BIT(0) << (x))
+#define EP0ISR BIT(0)
+
+/* U3D_EP0CSR */
+#define EP0_SENDSTALL BIT(25)
+#define EP0_FIFOFULL BIT(23)
+#define EP0_SENTSTALL BIT(22)
+#define EP0_DPHTX BIT(20)
+#define EP0_DATAEND BIT(19)
+#define EP0_TXPKTRDY BIT(18)
+#define EP0_SETUPPKTRDY BIT(17)
+#define EP0_RXPKTRDY BIT(16)
+#define EP0_MAXPKTSZ_MSK GENMASK(9, 0)
+#define EP0_MAXPKTSZ(x) ((x) & EP0_MAXPKTSZ_MSK)
+#define EP0_W1C_BITS (~(EP0_RXPKTRDY | EP0_SETUPPKTRDY | EP0_SENTSTALL))
+
+/* U3D_TX1CSR0 */
+#define TX_DMAREQEN BIT(29)
+#define TX_FIFOFULL BIT(25)
+#define TX_FIFOEMPTY BIT(24)
+#define TX_SENTSTALL BIT(22)
+#define TX_SENDSTALL BIT(21)
+#define TX_TXPKTRDY BIT(16)
+#define TX_TXMAXPKTSZ_MSK GENMASK(10, 0)
+#define TX_TXMAXPKTSZ(x) ((x) & TX_TXMAXPKTSZ_MSK)
+#define TX_W1C_BITS (~(TX_SENTSTALL))
+
+/* U3D_TX1CSR1 */
+#define TX_MAX_PKT_G2(x) (((x) & 0xff) << 24)
+#define TX_MULT_G2(x) (((x) & 0x7) << 21)
+#define TX_MULT_OG(x) (((x) & 0x3) << 22)
+#define TX_MAX_PKT_OG(x) (((x) & 0x3f) << 16)
+#define TX_SLOT(x) (((x) & 0x3f) << 8)
+#define TX_TYPE(x) (((x) & 0x3) << 4)
+#define TX_SS_BURST(x) (((x) & 0xf) << 0)
+#define TX_MULT(g2c, x) \
+({ \
+ typeof(x) x_ = (x); \
+ (g2c) ? TX_MULT_G2(x_) : TX_MULT_OG(x_); \
+})
+#define TX_MAX_PKT(g2c, x) \
+({ \
+ typeof(x) x_ = (x); \
+ (g2c) ? TX_MAX_PKT_G2(x_) : TX_MAX_PKT_OG(x_); \
+})
+
+/* for TX_TYPE & RX_TYPE */
+#define TYPE_BULK (0x0)
+#define TYPE_INT (0x1)
+#define TYPE_ISO (0x2)
+#define TYPE_MASK (0x3)
+
+/* U3D_TX1CSR2 */
+#define TX_BINTERVAL(x) (((x) & 0xff) << 24)
+#define TX_FIFOSEGSIZE(x) (((x) & 0xf) << 16)
+#define TX_FIFOADDR(x) (((x) & 0x1fff) << 0)
+
+/* U3D_RX1CSR0 */
+#define RX_DMAREQEN BIT(29)
+#define RX_SENTSTALL BIT(22)
+#define RX_SENDSTALL BIT(21)
+#define RX_RXPKTRDY BIT(16)
+#define RX_RXMAXPKTSZ_MSK GENMASK(10, 0)
+#define RX_RXMAXPKTSZ(x) ((x) & RX_RXMAXPKTSZ_MSK)
+#define RX_W1C_BITS (~(RX_SENTSTALL | RX_RXPKTRDY))
+
+/* U3D_RX1CSR1 */
+#define RX_MAX_PKT_G2(x) (((x) & 0xff) << 24)
+#define RX_MULT_G2(x) (((x) & 0x7) << 21)
+#define RX_MULT_OG(x) (((x) & 0x3) << 22)
+#define RX_MAX_PKT_OG(x) (((x) & 0x3f) << 16)
+#define RX_SLOT(x) (((x) & 0x3f) << 8)
+#define RX_TYPE(x) (((x) & 0x3) << 4)
+#define RX_SS_BURST(x) (((x) & 0xf) << 0)
+#define RX_MULT(g2c, x) \
+({ \
+ typeof(x) x_ = (x); \
+ (g2c) ? RX_MULT_G2(x_) : RX_MULT_OG(x_); \
+})
+#define RX_MAX_PKT(g2c, x) \
+({ \
+ typeof(x) x_ = (x); \
+ (g2c) ? RX_MAX_PKT_G2(x_) : RX_MAX_PKT_OG(x_); \
+})
+
+/* U3D_RX1CSR2 */
+#define RX_BINTERVAL(x) (((x) & 0xff) << 24)
+#define RX_FIFOSEGSIZE(x) (((x) & 0xf) << 16)
+#define RX_FIFOADDR(x) (((x) & 0x1fff) << 0)
+
+/* U3D_QCR0 */
+#define QMU_RX_CS_EN(x) (BIT(16) << (x))
+#define QMU_TX_CS_EN(x) (BIT(0) << (x))
+#define QMU_CS16B_EN BIT(0)
+
+/* U3D_QCR1 */
+#define QMU_TX_ZLP(x) (BIT(0) << (x))
+
+/* U3D_QCR3 */
+#define QMU_RX_COZ(x) (BIT(16) << (x))
+#define QMU_RX_ZLP(x) (BIT(0) << (x))
+
+/* U3D_TXQCSR1 */
+/* U3D_RXQCSR1 */
+#define QMU_Q_ACTIVE BIT(15)
+#define QMU_Q_STOP BIT(2)
+#define QMU_Q_RESUME BIT(1)
+#define QMU_Q_START BIT(0)
+
+/* U3D_QISAR0, U3D_QIER0, U3D_QIESR0, U3D_QIECR0 */
+#define QMU_RX_DONE_INT(x) (BIT(16) << (x))
+#define QMU_TX_DONE_INT(x) (BIT(0) << (x))
+
+/* U3D_QISAR1, U3D_QIER1, U3D_QIESR1, U3D_QIECR1 */
+#define RXQ_ZLPERR_INT BIT(20)
+#define RXQ_LENERR_INT BIT(18)
+#define RXQ_CSERR_INT BIT(17)
+#define RXQ_EMPTY_INT BIT(16)
+#define TXQ_LENERR_INT BIT(2)
+#define TXQ_CSERR_INT BIT(1)
+#define TXQ_EMPTY_INT BIT(0)
+
+/* U3D_TQERRIR0, U3D_TQERRIER0, U3D_TQERRIESR0, U3D_TQERRIECR0 */
+#define QMU_TX_LEN_ERR(x) (BIT(16) << (x))
+#define QMU_TX_CS_ERR(x) (BIT(0) << (x))
+
+/* U3D_RQERRIR0, U3D_RQERRIER0, U3D_RQERRIESR0, U3D_RQERRIECR0 */
+#define QMU_RX_LEN_ERR(x) (BIT(16) << (x))
+#define QMU_RX_CS_ERR(x) (BIT(0) << (x))
+
+/* U3D_RQERRIR1, U3D_RQERRIER1, U3D_RQERRIESR1, U3D_RQERRIECR1 */
+#define QMU_RX_ZLP_ERR(n) (BIT(16) << (n))
+
+/* U3D_CAP_EPINFO */
+#define CAP_RX_EP_NUM(x) (((x) >> 8) & 0x1f)
+#define CAP_TX_EP_NUM(x) ((x) & 0x1f)
+
+/* U3D_MISC_CTRL */
+#define VBUS_ON BIT(1)
+#define VBUS_FRC_EN BIT(0)
+
+/*---------------- SSUSB_EPCTL_CSR REGISTER DEFINITION ----------------*/
+
+#define U3D_DEVICE_CONF (SSUSB_EPCTL_CSR_BASE + 0x0000)
+#define U3D_EP_RST (SSUSB_EPCTL_CSR_BASE + 0x0004)
+
+#define U3D_DEV_LINK_INTR_ENABLE (SSUSB_EPCTL_CSR_BASE + 0x0050)
+#define U3D_DEV_LINK_INTR (SSUSB_EPCTL_CSR_BASE + 0x0054)
+
+/*---------------- SSUSB_EPCTL_CSR FIELD DEFINITION ----------------*/
+
+/* U3D_DEVICE_CONF */
+#define DEV_ADDR_MSK GENMASK(30, 24)
+#define DEV_ADDR(x) ((0x7f & (x)) << 24)
+#define HW_USB2_3_SEL BIT(18)
+#define SW_USB2_3_SEL_EN BIT(17)
+#define SW_USB2_3_SEL BIT(16)
+#define SSUSB_DEV_SPEED(x) ((x) & 0x7)
+
+/* U3D_EP_RST */
+#define EP1_IN_RST BIT(17)
+#define EP1_OUT_RST BIT(1)
+#define EP_RST(is_in, epnum) (((is_in) ? BIT(16) : BIT(0)) << (epnum))
+#define EP0_RST BIT(0)
+
+/* U3D_DEV_LINK_INTR_ENABLE */
+/* U3D_DEV_LINK_INTR */
+#define SSUSB_DEV_SPEED_CHG_INTR BIT(0)
+
+/*---------------- SSUSB_USB3_MAC_CSR REGISTER DEFINITION ----------------*/
+
+#define U3D_LTSSM_CTRL (SSUSB_USB3_MAC_CSR_BASE + 0x0010)
+#define U3D_USB3_CONFIG (SSUSB_USB3_MAC_CSR_BASE + 0x001C)
+
+#define U3D_LINK_STATE_MACHINE (SSUSB_USB3_MAC_CSR_BASE + 0x0134)
+#define U3D_LTSSM_INTR_ENABLE (SSUSB_USB3_MAC_CSR_BASE + 0x013C)
+#define U3D_LTSSM_INTR (SSUSB_USB3_MAC_CSR_BASE + 0x0140)
+
+#define U3D_U3U2_SWITCH_CTRL (SSUSB_USB3_MAC_CSR_BASE + 0x0170)
+
+/*---------------- SSUSB_USB3_MAC_CSR FIELD DEFINITION ----------------*/
+
+/* U3D_LTSSM_CTRL */
+#define FORCE_POLLING_FAIL BIT(4)
+#define FORCE_RXDETECT_FAIL BIT(3)
+#define SOFT_U3_EXIT_EN BIT(2)
+#define COMPLIANCE_EN BIT(1)
+#define U1_GO_U2_EN BIT(0)
+
+/* U3D_USB3_CONFIG */
+#define USB3_EN BIT(0)
+
+/* U3D_LINK_STATE_MACHINE */
+#define LTSSM_STATE(x) ((x) & 0x1f)
+
+/* U3D_LTSSM_INTR_ENABLE */
+/* U3D_LTSSM_INTR */
+#define U3_RESUME_INTR BIT(18)
+#define U3_LFPS_TMOUT_INTR BIT(17)
+#define VBUS_FALL_INTR BIT(16)
+#define VBUS_RISE_INTR BIT(15)
+#define RXDET_SUCCESS_INTR BIT(14)
+#define EXIT_U3_INTR BIT(13)
+#define EXIT_U2_INTR BIT(12)
+#define EXIT_U1_INTR BIT(11)
+#define ENTER_U3_INTR BIT(10)
+#define ENTER_U2_INTR BIT(9)
+#define ENTER_U1_INTR BIT(8)
+#define ENTER_U0_INTR BIT(7)
+#define RECOVERY_INTR BIT(6)
+#define WARM_RST_INTR BIT(5)
+#define HOT_RST_INTR BIT(4)
+#define LOOPBACK_INTR BIT(3)
+#define COMPLIANCE_INTR BIT(2)
+#define SS_DISABLE_INTR BIT(1)
+#define SS_INACTIVE_INTR BIT(0)
+
+/* U3D_U3U2_SWITCH_CTRL */
+#define SOFTCON_CLR_AUTO_EN BIT(0)
+
+/*---------------- SSUSB_USB3_SYS_CSR REGISTER DEFINITION ----------------*/
+
+#define U3D_LINK_UX_INACT_TIMER (SSUSB_USB3_SYS_CSR_BASE + 0x020C)
+#define U3D_LINK_POWER_CONTROL (SSUSB_USB3_SYS_CSR_BASE + 0x0210)
+#define U3D_LINK_ERR_COUNT (SSUSB_USB3_SYS_CSR_BASE + 0x0214)
+
+/*---------------- SSUSB_USB3_SYS_CSR FIELD DEFINITION ----------------*/
+
+/* U3D_LINK_UX_INACT_TIMER */
+#define DEV_U2_INACT_TIMEOUT_MSK GENMASK(23, 16)
+#define DEV_U2_INACT_TIMEOUT_VALUE(x) (((x) & 0xff) << 16)
+#define U2_INACT_TIMEOUT_MSK GENMASK(15, 8)
+#define U1_INACT_TIMEOUT_MSK GENMASK(7, 0)
+#define U1_INACT_TIMEOUT_VALUE(x) ((x) & 0xff)
+
+/* U3D_LINK_POWER_CONTROL */
+#define SW_U2_ACCEPT_ENABLE BIT(9)
+#define SW_U1_ACCEPT_ENABLE BIT(8)
+#define UX_EXIT BIT(5)
+#define LGO_U3 BIT(4)
+#define LGO_U2 BIT(3)
+#define LGO_U1 BIT(2)
+#define SW_U2_REQUEST_ENABLE BIT(1)
+#define SW_U1_REQUEST_ENABLE BIT(0)
+
+/* U3D_LINK_ERR_COUNT */
+#define CLR_LINK_ERR_CNT BIT(16)
+#define LINK_ERROR_COUNT GENMASK(15, 0)
+
+/*---------------- SSUSB_USB2_CSR REGISTER DEFINITION ----------------*/
+
+#define U3D_POWER_MANAGEMENT (SSUSB_USB2_CSR_BASE + 0x0004)
+#define U3D_DEVICE_CONTROL (SSUSB_USB2_CSR_BASE + 0x000C)
+#define U3D_USB2_TEST_MODE (SSUSB_USB2_CSR_BASE + 0x0014)
+#define U3D_COMMON_USB_INTR_ENABLE (SSUSB_USB2_CSR_BASE + 0x0018)
+#define U3D_COMMON_USB_INTR (SSUSB_USB2_CSR_BASE + 0x001C)
+#define U3D_LINK_RESET_INFO (SSUSB_USB2_CSR_BASE + 0x0024)
+#define U3D_USB20_FRAME_NUM (SSUSB_USB2_CSR_BASE + 0x003C)
+#define U3D_USB20_LPM_PARAMETER (SSUSB_USB2_CSR_BASE + 0x0044)
+#define U3D_USB20_MISC_CONTROL (SSUSB_USB2_CSR_BASE + 0x004C)
+#define U3D_USB20_OPSTATE (SSUSB_USB2_CSR_BASE + 0x0060)
+
+/*---------------- SSUSB_USB2_CSR FIELD DEFINITION ----------------*/
+
+/* U3D_POWER_MANAGEMENT */
+#define LPM_BESL_STALL BIT(14)
+#define LPM_BESLD_STALL BIT(13)
+#define LPM_RWP BIT(11)
+#define LPM_HRWE BIT(10)
+#define LPM_MODE(x) (((x) & 0x3) << 8)
+#define ISO_UPDATE BIT(7)
+#define SOFT_CONN BIT(6)
+#define HS_ENABLE BIT(5)
+#define RESUME BIT(2)
+#define SUSPENDM_ENABLE BIT(0)
+
+/* U3D_DEVICE_CONTROL */
+#define DC_HOSTREQ BIT(1)
+#define DC_SESSION BIT(0)
+
+/* U3D_USB2_TEST_MODE */
+#define U2U3_AUTO_SWITCH BIT(10)
+#define LPM_FORCE_STALL BIT(8)
+#define FIFO_ACCESS BIT(6)
+#define FORCE_FS BIT(5)
+#define FORCE_HS BIT(4)
+#define TEST_PACKET_MODE BIT(3)
+#define TEST_K_MODE BIT(2)
+#define TEST_J_MODE BIT(1)
+#define TEST_SE0_NAK_MODE BIT(0)
+
+/* U3D_COMMON_USB_INTR_ENABLE */
+/* U3D_COMMON_USB_INTR */
+#define LPM_RESUME_INTR BIT(9)
+#define LPM_INTR BIT(8)
+#define DISCONN_INTR BIT(5)
+#define CONN_INTR BIT(4)
+#define SOF_INTR BIT(3)
+#define RESET_INTR BIT(2)
+#define RESUME_INTR BIT(1)
+#define SUSPEND_INTR BIT(0)
+
+/* U3D_LINK_RESET_INFO */
+#define WTCHRP_MSK GENMASK(19, 16)
+
+/* U3D_USB20_LPM_PARAMETER */
+#define LPM_BESLCK_U3(x) (((x) & 0xf) << 12)
+#define LPM_BESLCK(x) (((x) & 0xf) << 8)
+#define LPM_BESLDCK(x) (((x) & 0xf) << 4)
+#define LPM_BESL GENMASK(3, 0)
+
+/* U3D_USB20_MISC_CONTROL */
+#define LPM_U3_ACK_EN BIT(0)
+
+/*---------------- SSUSB_SIFSLV_IPPC REGISTER DEFINITION ----------------*/
+
+#define U3D_SSUSB_IP_PW_CTRL0 (SSUSB_SIFSLV_IPPC_BASE + 0x0000)
+#define U3D_SSUSB_IP_PW_CTRL1 (SSUSB_SIFSLV_IPPC_BASE + 0x0004)
+#define U3D_SSUSB_IP_PW_CTRL2 (SSUSB_SIFSLV_IPPC_BASE + 0x0008)
+#define U3D_SSUSB_IP_PW_CTRL3 (SSUSB_SIFSLV_IPPC_BASE + 0x000C)
+#define U3D_SSUSB_IP_PW_STS1 (SSUSB_SIFSLV_IPPC_BASE + 0x0010)
+#define U3D_SSUSB_IP_PW_STS2 (SSUSB_SIFSLV_IPPC_BASE + 0x0014)
+#define U3D_SSUSB_OTG_STS (SSUSB_SIFSLV_IPPC_BASE + 0x0018)
+#define U3D_SSUSB_OTG_STS_CLR (SSUSB_SIFSLV_IPPC_BASE + 0x001C)
+#define U3D_SSUSB_IP_XHCI_CAP (SSUSB_SIFSLV_IPPC_BASE + 0x0024)
+#define U3D_SSUSB_IP_DEV_CAP (SSUSB_SIFSLV_IPPC_BASE + 0x0028)
+#define U3D_SSUSB_OTG_INT_EN (SSUSB_SIFSLV_IPPC_BASE + 0x002C)
+#define U3D_SSUSB_U3_CTRL_0P (SSUSB_SIFSLV_IPPC_BASE + 0x0030)
+#define U3D_SSUSB_U2_CTRL_0P (SSUSB_SIFSLV_IPPC_BASE + 0x0050)
+#define U3D_SSUSB_REF_CK_CTRL (SSUSB_SIFSLV_IPPC_BASE + 0x008C)
+#define U3D_SSUSB_DEV_RST_CTRL (SSUSB_SIFSLV_IPPC_BASE + 0x0098)
+#define U3D_SSUSB_HW_ID (SSUSB_SIFSLV_IPPC_BASE + 0x00A0)
+#define U3D_SSUSB_HW_SUB_ID (SSUSB_SIFSLV_IPPC_BASE + 0x00A4)
+#define U3D_SSUSB_IP_TRUNK_VERS (U3D_SSUSB_HW_SUB_ID)
+#define U3D_SSUSB_PRB_CTRL0 (SSUSB_SIFSLV_IPPC_BASE + 0x00B0)
+#define U3D_SSUSB_PRB_CTRL1 (SSUSB_SIFSLV_IPPC_BASE + 0x00B4)
+#define U3D_SSUSB_PRB_CTRL2 (SSUSB_SIFSLV_IPPC_BASE + 0x00B8)
+#define U3D_SSUSB_PRB_CTRL3 (SSUSB_SIFSLV_IPPC_BASE + 0x00BC)
+#define U3D_SSUSB_PRB_CTRL4 (SSUSB_SIFSLV_IPPC_BASE + 0x00C0)
+#define U3D_SSUSB_PRB_CTRL5 (SSUSB_SIFSLV_IPPC_BASE + 0x00C4)
+#define U3D_SSUSB_IP_SPARE0 (SSUSB_SIFSLV_IPPC_BASE + 0x00C8)
+
+/*---------------- SSUSB_SIFSLV_IPPC FIELD DEFINITION ----------------*/
+
+/* U3D_SSUSB_IP_PW_CTRL0 */
+#define SSUSB_IP_SW_RST BIT(0)
+
+/* U3D_SSUSB_IP_PW_CTRL1 */
+#define SSUSB_IP_HOST_PDN BIT(0)
+
+/* U3D_SSUSB_IP_PW_CTRL2 */
+#define SSUSB_IP_DEV_PDN BIT(0)
+
+/* U3D_SSUSB_IP_PW_CTRL3 */
+#define SSUSB_IP_PCIE_PDN BIT(0)
+
+/* U3D_SSUSB_IP_PW_STS1 */
+#define SSUSB_IP_SLEEP_STS BIT(30)
+#define SSUSB_U3_MAC_RST_B_STS BIT(16)
+#define SSUSB_XHCI_RST_B_STS BIT(11)
+#define SSUSB_SYS125_RST_B_STS BIT(10)
+#define SSUSB_REF_RST_B_STS BIT(8)
+#define SSUSB_SYSPLL_STABLE BIT(0)
+
+/* U3D_SSUSB_IP_PW_STS2 */
+#define SSUSB_U2_MAC_SYS_RST_B_STS BIT(0)
+
+/* U3D_SSUSB_OTG_STS */
+#define SSUSB_VBUS_VALID BIT(9)
+
+/* U3D_SSUSB_OTG_STS_CLR */
+#define SSUSB_VBUS_INTR_CLR BIT(6)
+
+/* U3D_SSUSB_IP_XHCI_CAP */
+#define SSUSB_IP_XHCI_U2_PORT_NUM(x) (((x) >> 8) & 0xff)
+#define SSUSB_IP_XHCI_U3_PORT_NUM(x) ((x) & 0xff)
+
+/* U3D_SSUSB_IP_DEV_CAP */
+#define SSUSB_IP_DEV_U3_PORT_NUM(x) ((x) & 0xff)
+
+/* U3D_SSUSB_OTG_INT_EN */
+#define SSUSB_VBUS_CHG_INT_A_EN BIT(7)
+#define SSUSB_VBUS_CHG_INT_B_EN BIT(6)
+
+/* U3D_SSUSB_U3_CTRL_0P */
+#define SSUSB_U3_PORT_SSP_SPEED BIT(9)
+#define SSUSB_U3_PORT_DUAL_MODE BIT(7)
+#define SSUSB_U3_PORT_HOST_SEL BIT(2)
+#define SSUSB_U3_PORT_PDN BIT(1)
+#define SSUSB_U3_PORT_DIS BIT(0)
+
+/* U3D_SSUSB_U2_CTRL_0P */
+#define SSUSB_U2_PORT_RG_IDDIG BIT(12)
+#define SSUSB_U2_PORT_FORCE_IDDIG BIT(11)
+#define SSUSB_U2_PORT_VBUSVALID BIT(9)
+#define SSUSB_U2_PORT_OTG_SEL BIT(7)
+#define SSUSB_U2_PORT_HOST BIT(2)
+#define SSUSB_U2_PORT_PDN BIT(1)
+#define SSUSB_U2_PORT_DIS BIT(0)
+#define SSUSB_U2_PORT_HOST_SEL (SSUSB_U2_PORT_VBUSVALID | SSUSB_U2_PORT_HOST)
+
+/* U3D_SSUSB_DEV_RST_CTRL */
+#define SSUSB_DEV_SW_RST BIT(0)
+
+/* U3D_SSUSB_IP_TRUNK_VERS */
+#define IP_TRUNK_VERS(x) (((x) >> 16) & 0xffff)
+
+#endif /* _SSUSB_HW_REGS_H_ */
diff --git a/drivers/usb/mtu3/mtu3_plat.c b/drivers/usb/mtu3/mtu3_plat.c
new file mode 100644
index 0000000..24ffdb3
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3_plat.c
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+#include <common.h>
+#include <dm/lists.h>
+#include <linux/iopoll.h>
+
+#include "mtu3.h"
+#include "mtu3_dr.h"
+
+void ssusb_set_force_mode(struct ssusb_mtk *ssusb,
+ enum mtu3_dr_force_mode mode)
+{
+ u32 value;
+
+ value = mtu3_readl(ssusb->ippc_base, SSUSB_U2_CTRL(0));
+ switch (mode) {
+ case MTU3_DR_FORCE_DEVICE:
+ value |= SSUSB_U2_PORT_FORCE_IDDIG | SSUSB_U2_PORT_RG_IDDIG;
+ break;
+ case MTU3_DR_FORCE_HOST:
+ value |= SSUSB_U2_PORT_FORCE_IDDIG;
+ value &= ~SSUSB_U2_PORT_RG_IDDIG;
+ break;
+ case MTU3_DR_FORCE_NONE:
+ value &= ~(SSUSB_U2_PORT_FORCE_IDDIG | SSUSB_U2_PORT_RG_IDDIG);
+ break;
+ default:
+ return;
+ }
+ mtu3_writel(ssusb->ippc_base, SSUSB_U2_CTRL(0), value);
+}
+
+/* u2-port0 should be powered on and enabled; */
+int ssusb_check_clocks(struct ssusb_mtk *ssusb, u32 ex_clks)
+{
+ void __iomem *ibase = ssusb->ippc_base;
+ u32 value, check_val;
+ int ret;
+
+ check_val = ex_clks | SSUSB_SYS125_RST_B_STS | SSUSB_SYSPLL_STABLE |
+ SSUSB_REF_RST_B_STS;
+
+ ret = readl_poll_timeout(ibase + U3D_SSUSB_IP_PW_STS1, value,
+ ((value & check_val) == check_val), 10000);
+ if (ret) {
+ dev_err(ssusb->dev, "clks of sts1 are not stable!\n");
+ return ret;
+ }
+
+ ret = readl_poll_timeout(ibase + U3D_SSUSB_IP_PW_STS2, value,
+ (value & SSUSB_U2_MAC_SYS_RST_B_STS), 10000);
+ if (ret) {
+ dev_err(ssusb->dev, "mac2 clock is not stable\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+int ssusb_phy_setup(struct ssusb_mtk *ssusb)
+{
+ struct udevice *dev = ssusb->dev;
+ struct phy_bulk *phys = &ssusb->phys;
+ int ret;
+
+ ret = generic_phy_get_bulk(dev, phys);
+ if (ret)
+ return ret;
+
+ ret = generic_phy_init_bulk(phys);
+ if (ret)
+ return ret;
+
+ ret = generic_phy_power_on_bulk(phys);
+ if (ret)
+ generic_phy_exit_bulk(phys);
+
+ return ret;
+}
+
+void ssusb_phy_shutdown(struct ssusb_mtk *ssusb)
+{
+ generic_phy_power_off_bulk(&ssusb->phys);
+ generic_phy_exit_bulk(&ssusb->phys);
+}
+
+static int ssusb_rscs_init(struct ssusb_mtk *ssusb)
+{
+ int ret = 0;
+
+ ret = regulator_set_enable(ssusb->vusb33_supply, true);
+ if (ret < 0 && ret != -ENOSYS) {
+ dev_err(ssusb->dev, "failed to enable vusb33\n");
+ goto vusb33_err;
+ }
+
+ ret = clk_enable_bulk(&ssusb->clks);
+ if (ret)
+ goto clks_err;
+
+ ret = ssusb_phy_setup(ssusb);
+ if (ret) {
+ dev_err(ssusb->dev, "failed to setup phy\n");
+ goto phy_err;
+ }
+
+ return 0;
+
+phy_err:
+ clk_disable_bulk(&ssusb->clks);
+clks_err:
+ regulator_set_enable(ssusb->vusb33_supply, false);
+vusb33_err:
+ return ret;
+}
+
+static void ssusb_rscs_exit(struct ssusb_mtk *ssusb)
+{
+ clk_disable_bulk(&ssusb->clks);
+ regulator_set_enable(ssusb->vusb33_supply, false);
+ ssusb_phy_shutdown(ssusb);
+}
+
+static void ssusb_ip_sw_reset(struct ssusb_mtk *ssusb)
+{
+ /* reset whole ip (xhci & u3d) */
+ mtu3_setbits(ssusb->ippc_base, U3D_SSUSB_IP_PW_CTRL0, SSUSB_IP_SW_RST);
+ udelay(1);
+ mtu3_clrbits(ssusb->ippc_base, U3D_SSUSB_IP_PW_CTRL0, SSUSB_IP_SW_RST);
+}
+
+static int get_ssusb_rscs(struct udevice *dev, struct ssusb_mtk *ssusb)
+{
+ struct udevice *child;
+ int ret;
+
+ ret = device_get_supply_regulator(dev, "vusb33-supply",
+ &ssusb->vusb33_supply);
+ if (ret) /* optional, ignore error */
+ dev_warn(dev, "can't get optional vusb33 %d\n", ret);
+
+ ret = device_get_supply_regulator(dev, "vbus-supply",
+ &ssusb->vbus_supply);
+ if (ret) /* optional, ignore error */
+ dev_warn(dev, "can't get optional vbus regulator %d!\n", ret);
+
+ ret = clk_get_bulk(dev, &ssusb->clks);
+ if (ret) {
+ dev_err(dev, "failed to get clocks %d!\n", ret);
+ return ret;
+ }
+
+ ssusb->ippc_base = devfdt_remap_addr_name(dev, "ippc");
+ if (!ssusb->ippc_base) {
+ dev_err(dev, "error mapping memory for ippc\n");
+ return -ENODEV;
+ }
+
+ ret = device_find_first_child(dev, &child);
+ if (ret || !child) {
+ dev_err(dev, "failed to get child %d!\n", ret);
+ return ret;
+ }
+
+ ssusb->mac_base = devfdt_remap_addr_name(child, "mac");
+ if (!ssusb->mac_base) {
+ dev_err(dev, "error mapping memory for mac\n");
+ return -ENODEV;
+ }
+
+ ssusb->dr_mode = usb_get_dr_mode(child->node);
+
+ if (ssusb->dr_mode == USB_DR_MODE_UNKNOWN ||
+ ssusb->dr_mode == USB_DR_MODE_OTG)
+ ssusb->dr_mode = USB_DR_MODE_PERIPHERAL;
+
+ if (IS_ENABLED(CONFIG_USB_MTU3_GADGET))
+ ssusb->dr_mode = USB_DR_MODE_PERIPHERAL;
+ else if (IS_ENABLED(CONFIG_USB_MTU3_HOST))
+ ssusb->dr_mode = USB_DR_MODE_HOST;
+
+ dev_info(dev, "dr_mode: %d, ippc: 0x%p, mac: 0x%p\n",
+ ssusb->dr_mode, ssusb->ippc_base, ssusb->mac_base);
+
+ return 0;
+}
+
+static int mtu3_probe(struct udevice *dev)
+{
+ struct ssusb_mtk *ssusb = dev_get_priv(dev);
+ int ret = -ENOMEM;
+
+ ssusb->dev = dev;
+
+ ret = get_ssusb_rscs(dev, ssusb);
+ if (ret)
+ return ret;
+
+ ret = ssusb_rscs_init(ssusb);
+ if (ret)
+ return ret;
+
+ ssusb_ip_sw_reset(ssusb);
+
+ return 0;
+}
+
+static int mtu3_remove(struct udevice *dev)
+{
+ struct ssusb_mtk *ssusb = dev_to_ssusb(dev);
+
+ ssusb_rscs_exit(ssusb);
+ return 0;
+}
+
+static const struct udevice_id ssusb_of_match[] = {
+ {.compatible = "mediatek,ssusb",},
+ {},
+};
+
+#if CONFIG_IS_ENABLED(DM_USB_GADGET)
+int dm_usb_gadget_handle_interrupts(struct udevice *dev)
+{
+ struct mtu3 *mtu = dev_get_priv(dev);
+
+ mtu3_irq(0, mtu);
+
+ return 0;
+}
+
+static int mtu3_gadget_probe(struct udevice *dev)
+{
+ struct ssusb_mtk *ssusb = dev_to_ssusb(dev->parent);
+ struct mtu3 *mtu = dev_get_priv(dev);
+
+ mtu->dev = dev;
+ ssusb->u3d = mtu;
+ return ssusb_gadget_init(ssusb);
+}
+
+static int mtu3_gadget_remove(struct udevice *dev)
+{
+ struct mtu3 *mtu = dev_get_priv(dev);
+
+ ssusb_gadget_exit(mtu->ssusb);
+ return 0;
+}
+
+U_BOOT_DRIVER(mtu3_peripheral) = {
+ .name = "mtu3-peripheral",
+ .id = UCLASS_USB_GADGET_GENERIC,
+ .of_match = ssusb_of_match,
+ .probe = mtu3_gadget_probe,
+ .remove = mtu3_gadget_remove,
+ .priv_auto_alloc_size = sizeof(struct mtu3),
+};
+#endif
+
+#if defined(CONFIG_SPL_USB_HOST_SUPPORT) || \
+ (!defined(CONFIG_SPL_BUILD) && defined(CONFIG_USB_HOST))
+static int mtu3_host_probe(struct udevice *dev)
+{
+ struct ssusb_mtk *ssusb = dev_to_ssusb(dev->parent);
+ struct mtu3_host *u3h = dev_get_priv(dev);
+ struct xhci_hcor *hcor;
+ int rc;
+
+ u3h->dev = dev;
+ ssusb->u3h = u3h;
+ rc = ssusb_host_init(ssusb);
+ if (rc)
+ return rc;
+
+ u3h->ctrl.quirks = XHCI_MTK_HOST;
+ hcor = (struct xhci_hcor *)((uintptr_t)u3h->hcd +
+ HC_LENGTH(xhci_readl(&u3h->hcd->cr_capbase)));
+
+ return xhci_register(dev, u3h->hcd, hcor);
+}
+
+static int mtu3_host_remove(struct udevice *dev)
+{
+ struct mtu3_host *u3h = dev_get_priv(dev);
+
+ xhci_deregister(dev);
+ ssusb_host_exit(u3h->ssusb);
+ return 0;
+}
+
+U_BOOT_DRIVER(mtu3_host) = {
+ .name = "mtu3-host",
+ .id = UCLASS_USB,
+ .of_match = ssusb_of_match,
+ .probe = mtu3_host_probe,
+ .remove = mtu3_host_remove,
+ .priv_auto_alloc_size = sizeof(struct mtu3_host),
+ .ops = &xhci_usb_ops,
+ .flags = DM_FLAG_ALLOC_PRIV_DMA,
+};
+#endif
+
+static int mtu3_glue_bind(struct udevice *parent)
+{
+ struct udevice *dev;
+ enum usb_dr_mode dr_mode;
+ const char *driver;
+ const char *name;
+ ofnode node;
+ int ret;
+
+ node = ofnode_by_compatible(parent->node, "mediatek,ssusb");
+ if (!ofnode_valid(node))
+ return -ENODEV;
+
+ name = ofnode_get_name(node);
+ dr_mode = usb_get_dr_mode(node);
+
+ switch (dr_mode) {
+#if CONFIG_IS_ENABLED(DM_USB_GADGET)
+ case USB_DR_MODE_PERIPHERAL:
+ case USB_DR_MODE_OTG:
+ dev_dbg(parent, "%s: dr_mode: peripheral\n", __func__);
+ driver = "mtu3-peripheral";
+ break;
+#endif
+
+#if defined(CONFIG_SPL_USB_HOST_SUPPORT) || \
+ (!defined(CONFIG_SPL_BUILD) && defined(CONFIG_USB_HOST))
+ case USB_DR_MODE_HOST:
+ dev_dbg(parent, "%s: dr_mode: host\n", __func__);
+ driver = "mtu3-host";
+ break;
+#endif
+ default:
+ dev_err(parent, "%s: unsupported dr_mode %d\n",
+ __func__, dr_mode);
+ return -ENODEV;
+ };
+
+ dev_dbg(parent, "%s: node name: %s, driver %s, dr_mode %d\n",
+ __func__, name, driver, dr_mode);
+
+ ret = device_bind_driver_to_node(parent, driver, name, node, &dev);
+ if (ret)
+ dev_err("%s: not able to bind usb device mode\n", __func__);
+
+ return ret;
+}
+
+static const struct udevice_id mtu3_of_match[] = {
+ {.compatible = "mediatek,mtu3",},
+ {},
+};
+
+U_BOOT_DRIVER(mtu3) = {
+ .name = "mtu3",
+ .id = UCLASS_NOP,
+ .of_match = mtu3_of_match,
+ .bind = mtu3_glue_bind,
+ .probe = mtu3_probe,
+ .remove = mtu3_remove,
+ .priv_auto_alloc_size = sizeof(struct ssusb_mtk),
+};
diff --git a/drivers/usb/mtu3/mtu3_qmu.c b/drivers/usb/mtu3/mtu3_qmu.c
new file mode 100644
index 0000000..f602e50
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3_qmu.c
@@ -0,0 +1,504 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * mtu3_qmu.c - Queue Management Unit driver for device controller
+ *
+ * Copyright (C) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+/*
+ * Queue Management Unit (QMU) is designed to unload SW effort
+ * to serve DMA interrupts.
+ * By preparing General Purpose Descriptor (GPD) and Buffer Descriptor (BD),
+ * SW links data buffers and triggers QMU to send / receive data to
+ * host / from device at a time.
+ * And now only GPD is supported.
+ *
+ * For more detailed information, please refer to QMU Programming Guide
+ */
+
+#include <asm/cache.h>
+#include <linux/iopoll.h>
+#include <linux/types.h>
+
+#include "mtu3.h"
+
+#define QMU_CHECKSUM_LEN 16
+
+#define GPD_FLAGS_HWO BIT(0)
+#define GPD_FLAGS_BDP BIT(1)
+#define GPD_FLAGS_BPS BIT(2)
+#define GPD_FLAGS_IOC BIT(7)
+
+#define GPD_EXT_FLAG_ZLP BIT(5)
+
+#define DCACHELINE_SIZE CONFIG_SYS_CACHELINE_SIZE
+
+void mtu3_flush_cache(uintptr_t addr, u32 len)
+{
+ WARN_ON(!(void *)addr || len == 0);
+
+ flush_dcache_range(addr & ~(DCACHELINE_SIZE - 1),
+ ALIGN(addr + len, DCACHELINE_SIZE));
+}
+
+void mtu3_inval_cache(uintptr_t addr, u32 len)
+{
+ WARN_ON(!(void *)addr || len == 0);
+
+ invalidate_dcache_range(addr & ~(DCACHELINE_SIZE - 1),
+ ALIGN(addr + len, DCACHELINE_SIZE));
+}
+
+static struct qmu_gpd *gpd_dma_to_virt(struct mtu3_gpd_ring *ring,
+ dma_addr_t dma_addr)
+{
+ dma_addr_t dma_base = ring->dma;
+ struct qmu_gpd *gpd_head = ring->start;
+ u32 offset = (dma_addr - dma_base) / sizeof(*gpd_head);
+
+ if (offset >= MAX_GPD_NUM)
+ return NULL;
+
+ return gpd_head + offset;
+}
+
+static dma_addr_t gpd_virt_to_dma(struct mtu3_gpd_ring *ring,
+ struct qmu_gpd *gpd)
+{
+ dma_addr_t dma_base = ring->dma;
+ struct qmu_gpd *gpd_head = ring->start;
+ u32 offset;
+
+ offset = gpd - gpd_head;
+ if (offset >= MAX_GPD_NUM)
+ return 0;
+
+ return dma_base + (offset * sizeof(*gpd));
+}
+
+static void gpd_ring_init(struct mtu3_gpd_ring *ring, struct qmu_gpd *gpd)
+{
+ ring->start = gpd;
+ ring->enqueue = gpd;
+ ring->dequeue = gpd;
+ ring->end = gpd + MAX_GPD_NUM - 1;
+}
+
+static void reset_gpd_list(struct mtu3_ep *mep)
+{
+ struct mtu3_gpd_ring *ring = &mep->gpd_ring;
+ struct qmu_gpd *gpd = ring->start;
+
+ if (gpd) {
+ gpd->flag &= ~GPD_FLAGS_HWO;
+ gpd_ring_init(ring, gpd);
+ mtu3_flush_cache((uintptr_t)gpd, sizeof(*gpd));
+ }
+}
+
+int mtu3_gpd_ring_alloc(struct mtu3_ep *mep)
+{
+ struct qmu_gpd *gpd;
+ struct mtu3_gpd_ring *ring = &mep->gpd_ring;
+
+ /* software own all gpds as default */
+ gpd = memalign(DCACHELINE_SIZE, QMU_GPD_RING_SIZE);
+ if (!gpd)
+ return -ENOMEM;
+
+ memset(gpd, 0, QMU_GPD_RING_SIZE);
+ ring->dma = (dma_addr_t)gpd;
+ gpd_ring_init(ring, gpd);
+
+ return 0;
+}
+
+void mtu3_gpd_ring_free(struct mtu3_ep *mep)
+{
+ struct mtu3_gpd_ring *ring = &mep->gpd_ring;
+
+ kfree(ring->start);
+ memset(ring, 0, sizeof(*ring));
+}
+
+void mtu3_qmu_resume(struct mtu3_ep *mep)
+{
+ struct mtu3 *mtu = mep->mtu;
+ void __iomem *mbase = mtu->mac_base;
+ int epnum = mep->epnum;
+ u32 offset;
+
+ offset = mep->is_in ? USB_QMU_TQCSR(epnum) : USB_QMU_RQCSR(epnum);
+
+ mtu3_writel(mbase, offset, QMU_Q_RESUME);
+ if (!(mtu3_readl(mbase, offset) & QMU_Q_ACTIVE))
+ mtu3_writel(mbase, offset, QMU_Q_RESUME);
+}
+
+static struct qmu_gpd *advance_enq_gpd(struct mtu3_gpd_ring *ring)
+{
+ if (ring->enqueue < ring->end)
+ ring->enqueue++;
+ else
+ ring->enqueue = ring->start;
+
+ return ring->enqueue;
+}
+
+static struct qmu_gpd *advance_deq_gpd(struct mtu3_gpd_ring *ring)
+{
+ if (ring->dequeue < ring->end)
+ ring->dequeue++;
+ else
+ ring->dequeue = ring->start;
+
+ return ring->dequeue;
+}
+
+/* check if a ring is emtpy */
+static int gpd_ring_empty(struct mtu3_gpd_ring *ring)
+{
+ struct qmu_gpd *enq = ring->enqueue;
+ struct qmu_gpd *next;
+
+ if (ring->enqueue < ring->end)
+ next = enq + 1;
+ else
+ next = ring->start;
+
+ /* one gpd is reserved to simplify gpd preparation */
+ return next == ring->dequeue;
+}
+
+int mtu3_prepare_transfer(struct mtu3_ep *mep)
+{
+ return gpd_ring_empty(&mep->gpd_ring);
+}
+
+static int mtu3_prepare_tx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
+{
+ struct qmu_gpd *enq;
+ struct mtu3_gpd_ring *ring = &mep->gpd_ring;
+ struct qmu_gpd *gpd = ring->enqueue;
+ struct usb_request *req = &mreq->request;
+
+ /* set all fields to zero as default value */
+ memset(gpd, 0, sizeof(*gpd));
+
+ gpd->buffer = cpu_to_le32((u32)req->dma);
+ gpd->buf_len = cpu_to_le16(req->length);
+
+ /* get the next GPD */
+ enq = advance_enq_gpd(ring);
+ dev_dbg(mep->mtu->dev, "TX-EP%d queue gpd=%p, enq=%p\n",
+ mep->epnum, gpd, enq);
+
+ enq->flag &= ~GPD_FLAGS_HWO;
+ gpd->next_gpd = cpu_to_le32((u32)gpd_virt_to_dma(ring, enq));
+
+ if (req->zero)
+ gpd->ext_flag |= GPD_EXT_FLAG_ZLP;
+
+ gpd->flag |= GPD_FLAGS_IOC | GPD_FLAGS_HWO;
+
+ mreq->gpd = gpd;
+
+ if (req->length)
+ mtu3_flush_cache((uintptr_t)req->buf, req->length);
+
+ mtu3_flush_cache((uintptr_t)gpd, sizeof(*gpd));
+
+ return 0;
+}
+
+static int mtu3_prepare_rx_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
+{
+ struct qmu_gpd *enq;
+ struct mtu3_gpd_ring *ring = &mep->gpd_ring;
+ struct qmu_gpd *gpd = ring->enqueue;
+ struct usb_request *req = &mreq->request;
+
+ /* set all fields to zero as default value */
+ memset(gpd, 0, sizeof(*gpd));
+
+ gpd->buffer = cpu_to_le32((u32)req->dma);
+ gpd->data_buf_len = cpu_to_le16(req->length);
+
+ /* get the next GPD */
+ enq = advance_enq_gpd(ring);
+ dev_dbg(mep->mtu->dev, "RX-EP%d queue gpd=%p, enq=%p\n",
+ mep->epnum, gpd, enq);
+
+ enq->flag &= ~GPD_FLAGS_HWO;
+ gpd->next_gpd = cpu_to_le32((u32)gpd_virt_to_dma(ring, enq));
+ gpd->flag |= GPD_FLAGS_IOC | GPD_FLAGS_HWO;
+
+ mreq->gpd = gpd;
+
+ mtu3_inval_cache((uintptr_t)req->buf, req->length);
+ mtu3_flush_cache((uintptr_t)gpd, sizeof(*gpd));
+
+ return 0;
+}
+
+void mtu3_insert_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq)
+{
+ if (mep->is_in)
+ mtu3_prepare_tx_gpd(mep, mreq);
+ else
+ mtu3_prepare_rx_gpd(mep, mreq);
+}
+
+int mtu3_qmu_start(struct mtu3_ep *mep)
+{
+ struct mtu3 *mtu = mep->mtu;
+ void __iomem *mbase = mtu->mac_base;
+ struct mtu3_gpd_ring *ring = &mep->gpd_ring;
+ u8 epnum = mep->epnum;
+
+ if (mep->is_in) {
+ /* set QMU start address */
+ mtu3_writel(mbase, USB_QMU_TQSAR(epnum), ring->dma);
+ mtu3_setbits(mbase, MU3D_EP_TXCR0(epnum), TX_DMAREQEN);
+ /* send zero length packet according to ZLP flag in GPD */
+ mtu3_setbits(mbase, U3D_QCR1, QMU_TX_ZLP(epnum));
+ mtu3_writel(mbase, U3D_TQERRIESR0,
+ QMU_TX_LEN_ERR(epnum) | QMU_TX_CS_ERR(epnum));
+
+ if (mtu3_readl(mbase, USB_QMU_TQCSR(epnum)) & QMU_Q_ACTIVE) {
+ dev_warn(mtu->dev, "Tx %d Active Now!\n", epnum);
+ return 0;
+ }
+ mtu3_writel(mbase, USB_QMU_TQCSR(epnum), QMU_Q_START);
+
+ } else {
+ mtu3_writel(mbase, USB_QMU_RQSAR(epnum), ring->dma);
+ mtu3_setbits(mbase, MU3D_EP_RXCR0(epnum), RX_DMAREQEN);
+ /* don't expect ZLP */
+ mtu3_clrbits(mbase, U3D_QCR3, QMU_RX_ZLP(epnum));
+ /* move to next GPD when receive ZLP */
+ mtu3_setbits(mbase, U3D_QCR3, QMU_RX_COZ(epnum));
+ mtu3_writel(mbase, U3D_RQERRIESR0,
+ QMU_RX_LEN_ERR(epnum) | QMU_RX_CS_ERR(epnum));
+ mtu3_writel(mbase, U3D_RQERRIESR1, QMU_RX_ZLP_ERR(epnum));
+
+ if (mtu3_readl(mbase, USB_QMU_RQCSR(epnum)) & QMU_Q_ACTIVE) {
+ dev_warn(mtu->dev, "Rx %d Active Now!\n", epnum);
+ return 0;
+ }
+ mtu3_writel(mbase, USB_QMU_RQCSR(epnum), QMU_Q_START);
+ }
+
+ return 0;
+}
+
+/* may called in atomic context */
+void mtu3_qmu_stop(struct mtu3_ep *mep)
+{
+ struct mtu3 *mtu = mep->mtu;
+ void __iomem *mbase = mtu->mac_base;
+ int epnum = mep->epnum;
+ u32 value = 0;
+ u32 qcsr;
+ int ret;
+
+ qcsr = mep->is_in ? USB_QMU_TQCSR(epnum) : USB_QMU_RQCSR(epnum);
+
+ if (!(mtu3_readl(mbase, qcsr) & QMU_Q_ACTIVE)) {
+ dev_dbg(mtu->dev, "%s's qmu is inactive now!\n", mep->name);
+ return;
+ }
+ mtu3_writel(mbase, qcsr, QMU_Q_STOP);
+
+ ret = readl_poll_timeout(mbase + qcsr, value,
+ !(value & QMU_Q_ACTIVE), 1000);
+ if (ret) {
+ dev_err(mtu->dev, "stop %s's qmu failed\n", mep->name);
+ return;
+ }
+
+ dev_dbg(mtu->dev, "%s's qmu stop now!\n", mep->name);
+}
+
+void mtu3_qmu_flush(struct mtu3_ep *mep)
+{
+ dev_dbg(mep->mtu->dev, "%s flush QMU %s\n", __func__,
+ ((mep->is_in) ? "TX" : "RX"));
+
+ /*Stop QMU */
+ mtu3_qmu_stop(mep);
+ reset_gpd_list(mep);
+}
+
+/*
+ * NOTE: request list maybe is already empty as following case:
+ * queue_tx --> qmu_interrupt(clear interrupt pending, schedule tasklet)-->
+ * queue_tx --> process_tasklet(meanwhile, the second one is transferred,
+ * tasklet process both of them)-->qmu_interrupt for second one.
+ * To avoid upper case, put qmu_done_tx in ISR directly to process it.
+ */
+static void qmu_done_tx(struct mtu3 *mtu, u8 epnum)
+{
+ struct mtu3_ep *mep = mtu->in_eps + epnum;
+ struct mtu3_gpd_ring *ring = &mep->gpd_ring;
+ void __iomem *mbase = mtu->mac_base;
+ struct qmu_gpd *gpd = ring->dequeue;
+ struct qmu_gpd *gpd_current = NULL;
+ struct usb_request *req = NULL;
+ struct mtu3_request *mreq;
+ dma_addr_t cur_gpd_dma;
+
+ /*transfer phy address got from QMU register to virtual address */
+ cur_gpd_dma = mtu3_readl(mbase, USB_QMU_TQCPR(epnum));
+ gpd_current = gpd_dma_to_virt(ring, cur_gpd_dma);
+ mtu3_inval_cache((uintptr_t)gpd, sizeof(*gpd));
+
+ dev_dbg(mtu->dev, "%s EP%d, last=%p, current=%p, enq=%p\n",
+ __func__, epnum, gpd, gpd_current, ring->enqueue);
+
+ while (gpd != gpd_current && !(gpd->flag & GPD_FLAGS_HWO)) {
+ mreq = next_request(mep);
+
+ if (!mreq || mreq->gpd != gpd) {
+ dev_err(mtu->dev, "no correct TX req is found\n");
+ break;
+ }
+
+ req = &mreq->request;
+ req->actual = le16_to_cpu(gpd->buf_len);
+ mtu3_req_complete(mep, req, 0);
+
+ gpd = advance_deq_gpd(ring);
+ mtu3_inval_cache((uintptr_t)gpd, sizeof(*gpd));
+ }
+
+ dev_dbg(mtu->dev, "%s EP%d, deq=%p, enq=%p, complete\n",
+ __func__, epnum, ring->dequeue, ring->enqueue);
+}
+
+static void qmu_done_rx(struct mtu3 *mtu, u8 epnum)
+{
+ struct mtu3_ep *mep = mtu->out_eps + epnum;
+ struct mtu3_gpd_ring *ring = &mep->gpd_ring;
+ void __iomem *mbase = mtu->mac_base;
+ struct qmu_gpd *gpd = ring->dequeue;
+ struct qmu_gpd *gpd_current = NULL;
+ struct usb_request *req = NULL;
+ struct mtu3_request *mreq;
+ dma_addr_t cur_gpd_dma;
+
+ cur_gpd_dma = mtu3_readl(mbase, USB_QMU_RQCPR(epnum));
+ gpd_current = gpd_dma_to_virt(ring, cur_gpd_dma);
+ mtu3_inval_cache((uintptr_t)gpd, sizeof(*gpd));
+
+ dev_dbg(mtu->dev, "%s EP%d, last=%p, current=%p, enq=%p\n",
+ __func__, epnum, gpd, gpd_current, ring->enqueue);
+
+ while (gpd != gpd_current && !(gpd->flag & GPD_FLAGS_HWO)) {
+ mreq = next_request(mep);
+
+ if (!mreq || mreq->gpd != gpd) {
+ dev_err(mtu->dev, "no correct RX req is found\n");
+ break;
+ }
+ req = &mreq->request;
+
+ req->actual = le16_to_cpu(gpd->buf_len);
+ mtu3_req_complete(mep, req, 0);
+
+ gpd = advance_deq_gpd(ring);
+ mtu3_inval_cache((uintptr_t)gpd, sizeof(*gpd));
+ }
+
+ dev_dbg(mtu->dev, "%s EP%d, deq=%p, enq=%p, complete\n",
+ __func__, epnum, ring->dequeue, ring->enqueue);
+}
+
+static void qmu_done_isr(struct mtu3 *mtu, u32 done_status)
+{
+ int i;
+
+ for (i = 1; i < mtu->num_eps; i++) {
+ if (done_status & QMU_RX_DONE_INT(i))
+ qmu_done_rx(mtu, i);
+ if (done_status & QMU_TX_DONE_INT(i))
+ qmu_done_tx(mtu, i);
+ }
+}
+
+static void qmu_exception_isr(struct mtu3 *mtu, u32 qmu_status)
+{
+ void __iomem *mbase = mtu->mac_base;
+ u32 errval;
+ int i;
+
+ if ((qmu_status & RXQ_CSERR_INT) || (qmu_status & RXQ_LENERR_INT)) {
+ errval = mtu3_readl(mbase, U3D_RQERRIR0);
+ for (i = 1; i < mtu->num_eps; i++) {
+ if (errval & QMU_RX_CS_ERR(i))
+ dev_err(mtu->dev, "Rx %d CS error!\n", i);
+
+ if (errval & QMU_RX_LEN_ERR(i))
+ dev_err(mtu->dev, "RX %d Length error\n", i);
+ }
+ mtu3_writel(mbase, U3D_RQERRIR0, errval);
+ }
+
+ if (qmu_status & RXQ_ZLPERR_INT) {
+ errval = mtu3_readl(mbase, U3D_RQERRIR1);
+ for (i = 1; i < mtu->num_eps; i++) {
+ if (errval & QMU_RX_ZLP_ERR(i))
+ dev_dbg(mtu->dev, "RX EP%d Recv ZLP\n", i);
+ }
+ mtu3_writel(mbase, U3D_RQERRIR1, errval);
+ }
+
+ if ((qmu_status & TXQ_CSERR_INT) || (qmu_status & TXQ_LENERR_INT)) {
+ errval = mtu3_readl(mbase, U3D_TQERRIR0);
+ for (i = 1; i < mtu->num_eps; i++) {
+ if (errval & QMU_TX_CS_ERR(i))
+ dev_err(mtu->dev, "Tx %d checksum error!\n", i);
+
+ if (errval & QMU_TX_LEN_ERR(i))
+ dev_err(mtu->dev, "Tx %d zlp error!\n", i);
+ }
+ mtu3_writel(mbase, U3D_TQERRIR0, errval);
+ }
+}
+
+irqreturn_t mtu3_qmu_isr(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+ u32 qmu_status;
+ u32 qmu_done_status;
+
+ /* U3D_QISAR1 is read update */
+ qmu_status = mtu3_readl(mbase, U3D_QISAR1);
+ qmu_status &= mtu3_readl(mbase, U3D_QIER1);
+
+ qmu_done_status = mtu3_readl(mbase, U3D_QISAR0);
+ qmu_done_status &= mtu3_readl(mbase, U3D_QIER0);
+ mtu3_writel(mbase, U3D_QISAR0, qmu_done_status); /* W1C */
+ dev_dbg(mtu->dev, "=== QMUdone[tx=%x, rx=%x] QMUexp[%x] ===\n",
+ (qmu_done_status & 0xFFFF), qmu_done_status >> 16,
+ qmu_status);
+
+ if (qmu_done_status)
+ qmu_done_isr(mtu, qmu_done_status);
+
+ if (qmu_status)
+ qmu_exception_isr(mtu, qmu_status);
+
+ return IRQ_HANDLED;
+}
+
+void mtu3_qmu_init(struct mtu3 *mtu)
+{
+ compiletime_assert(QMU_GPD_SIZE == 16, "QMU_GPD size SHOULD be 16B");
+}
+
+void mtu3_qmu_exit(struct mtu3 *mtu)
+{
+}
diff --git a/drivers/usb/mtu3/mtu3_qmu.h b/drivers/usb/mtu3/mtu3_qmu.h
new file mode 100644
index 0000000..ba8a3aa
--- /dev/null
+++ b/drivers/usb/mtu3/mtu3_qmu.h
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * mtu3_qmu.h - Queue Management Unit driver header
+ *
+ * Copyright (C) 2016 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+#ifndef __MTK_QMU_H__
+#define __MTK_QMU_H__
+
+#define MAX_GPD_NUM 16
+#define QMU_GPD_SIZE (sizeof(struct qmu_gpd))
+#define QMU_GPD_RING_SIZE (MAX_GPD_NUM * QMU_GPD_SIZE)
+
+#define GPD_BUF_SIZE 65532
+
+void mtu3_flush_cache(uintptr_t addr, u32 len);
+void mtu3_inval_cache(uintptr_t addr, u32 len);
+
+void mtu3_qmu_stop(struct mtu3_ep *mep);
+int mtu3_qmu_start(struct mtu3_ep *mep);
+void mtu3_qmu_resume(struct mtu3_ep *mep);
+void mtu3_qmu_flush(struct mtu3_ep *mep);
+
+void mtu3_insert_gpd(struct mtu3_ep *mep, struct mtu3_request *mreq);
+int mtu3_prepare_transfer(struct mtu3_ep *mep);
+
+int mtu3_gpd_ring_alloc(struct mtu3_ep *mep);
+void mtu3_gpd_ring_free(struct mtu3_ep *mep);
+
+irqreturn_t mtu3_qmu_isr(struct mtu3 *mtu);
+void mtu3_qmu_init(struct mtu3 *mtu);
+void mtu3_qmu_exit(struct mtu3 *mtu);
+
+#endif
--
1.9.1
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [PATCH next v7 06/10] usb: gadget: Add bcdDevice for the MTU3 USB Gadget Controller
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
` (4 preceding siblings ...)
2020-09-18 9:10 ` [PATCH next v7 05/10] usb: add MediaTek USB3 DRD driver Chunfeng Yun
@ 2020-09-18 9:10 ` Chunfeng Yun
2020-10-13 14:28 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 07/10] arm: dts: mt8512: add usb related nodes Chunfeng Yun
` (4 subsequent siblings)
10 siblings, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
Add an entry in usb_gadget_controller_number() for the MTU3
gadget controller. It is used to bind the USB Ethernet driver.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v4~v7: no changes
v3: new patch
---
drivers/usb/gadget/gadget_chips.h | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/drivers/usb/gadget/gadget_chips.h b/drivers/usb/gadget/gadget_chips.h
index 587204c..0cdf47c 100644
--- a/drivers/usb/gadget/gadget_chips.h
+++ b/drivers/usb/gadget/gadget_chips.h
@@ -161,6 +161,12 @@
#define gadget_is_max3420(g) 0
#endif
+#ifdef CONFIG_USB_MTU3_GADGET
+#define gadget_is_mtu3(g) (!strcmp("mtu3-gadget", (g)->name))
+#else
+#define gadget_is_mtu3(g) 0
+#endif
+
/**
* usb_gadget_controller_number - support bcdDevice id convention
* @gadget: the controller being driven
@@ -224,5 +230,7 @@ static inline int usb_gadget_controller_number(struct usb_gadget *gadget)
return 0x24;
else if (gadget_is_max3420(gadget))
return 0x25;
+ else if (gadget_is_mtu3(gadget))
+ return 0x26;
return -ENOENT;
}
--
1.9.1
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [PATCH next v7 07/10] arm: dts: mt8512: add usb related nodes
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
` (5 preceding siblings ...)
2020-09-18 9:10 ` [PATCH next v7 06/10] usb: gadget: Add bcdDevice for the MTU3 USB Gadget Controller Chunfeng Yun
@ 2020-09-18 9:10 ` Chunfeng Yun
2020-10-13 14:32 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 08/10] configs: mt8512: enable fastboot Chunfeng Yun
` (3 subsequent siblings)
10 siblings, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
Add usb, usb phy, and fixed regulators nodes
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v5~v7: no changes
v4: add host related properties, add subnode.
v3: remove unused property mediatek,discth
v2: no changes
---
arch/arm/dts/mt8512-bm1-emmc.dts | 34 ++++++++++++++++++++++++++++
arch/arm/dts/mt8512.dtsi | 49 +++++++++++++++++++++++++++++++++++++++-
2 files changed, 82 insertions(+), 1 deletion(-)
diff --git a/arch/arm/dts/mt8512-bm1-emmc.dts b/arch/arm/dts/mt8512-bm1-emmc.dts
index 296ed93..12511b5 100644
--- a/arch/arm/dts/mt8512-bm1-emmc.dts
+++ b/arch/arm/dts/mt8512-bm1-emmc.dts
@@ -43,6 +43,25 @@
regulator-boot-on;
regulator-always-on;
};
+
+ usb_p0_vbus: regulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "p0_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 27 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_p1_vbus: regulator at 1 {
+ compatible = "regulator-fixed";
+ regulator-name = "p1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 32 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
};
&mmc0 {
@@ -95,6 +114,21 @@
};
};
+&ssusb {
+ dr_mode = "peripheral";
+ maximum-speed = "high-speed";
+ status = "okay";
+};
+
+&usb3 {
+ vbus-supply = <&usb_p0_vbus>;
+ status = "okay";
+};
+
+&u3phy {
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
diff --git a/arch/arm/dts/mt8512.dtsi b/arch/arm/dts/mt8512.dtsi
index 01a02a7..bdb84f8 100644
--- a/arch/arm/dts/mt8512.dtsi
+++ b/arch/arm/dts/mt8512.dtsi
@@ -9,6 +9,7 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy.h>
/ {
compatible = "mediatek,mt8512";
@@ -100,6 +101,52 @@
status = "disabled";
};
+ usb3: usb at 11213e00 {
+ compatible = "mediatek,mt8512-mtu3", "mediatek,mtu3";
+ reg = <0x11213e00 0x0100>;
+ reg-names = "ippc";
+ phys = <&u2port0 PHY_TYPE_USB2>, <&u2port1 PHY_TYPE_USB2>;
+ clocks = <&infracfg CLK_INFRA_USB_SYS>,
+ <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>,
+ <&infracfg CLK_INFRA_ICUSB>;
+ clock-names = "sys_ck", "ref_ck", "mcu_ck";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ ssusb: usb at 11210000 {
+ compatible = "mediatek,ssusb";
+ reg = <0x11210000 0x3e00>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>;
+ reg-names = "mac";
+ status = "disabled";
+ };
+ };
+
+ u3phy: usb-phy at 11cc0000 {
+ compatible = "mediatek,mt8512-tphy",
+ "mediatek,generic-tphy-v2";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ u2port0: usb-phy at 11cc0000 {
+ reg = <0x11cc0000 0x400>;
+ clocks = <&topckgen CLK_TOP_USB20_48M_EN>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+
+ u2port1: usb-phy at 11c40000 {
+ reg = <0x11c40000 0x400>;
+ #phy-cells = <1>;
+ status = "okay";
+ };
+ };
+
mmc0: mmc at 11230000 {
compatible = "mediatek,mt8512-mmc";
reg = <0x11230000 0x1000>,
@@ -112,4 +159,4 @@
status = "disabled";
};
-};
\ No newline at end of file
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [PATCH next v7 08/10] configs: mt8512: enable fastboot
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
` (6 preceding siblings ...)
2020-09-18 9:10 ` [PATCH next v7 07/10] arm: dts: mt8512: add usb related nodes Chunfeng Yun
@ 2020-09-18 9:10 ` Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 09/10] configs: mt8512: add USB host related configs Chunfeng Yun
` (2 subsequent siblings)
10 siblings, 0 replies; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
Enable fastboot to support download image from usb, also enable
usb related drivers, such as usb phy etc.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2~v7: no changes
---
configs/mt8512_bm1_emmc_defconfig | 19 +++++++++++++++++++
1 file changed, 19 insertions(+)
diff --git a/configs/mt8512_bm1_emmc_defconfig b/configs/mt8512_bm1_emmc_defconfig
index 950507f..d41446f 100644
--- a/configs/mt8512_bm1_emmc_defconfig
+++ b/configs/mt8512_bm1_emmc_defconfig
@@ -9,6 +9,7 @@ CONFIG_DM_GPIO=y
CONFIG_TARGET_MT8512=y
CONFIG_DEFAULT_DEVICE_TREE="mt8512-bm1-emmc"
CONFIG_FIT=y
+CONFIG_EFI_PARTITION=y
CONFIG_FIT_SIGNATURE=y
CONFIG_DEFAULT_FDT_FILE="mt8512-bm1-emmc.dtb"
CONFIG_SYS_PROMPT="MT8512> "
@@ -26,6 +27,15 @@ CONFIG_PINCONF=y
CONFIG_PINCTRL_MT8512=y
CONFIG_RAM=y
CONFIG_BAUDRATE=921600
+CONFIG_USB_FUNCTION_FASTBOOT=y
+CONFIG_FASTBOOT_BUF_ADDR=0x56000000
+CONFIG_FASTBOOT_BUF_SIZE=0x1e00000
+CONFIG_FASTBOOT_FLASH=y
+CONFIG_FASTBOOT_FLASH_MMC_DEV=0
+CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT=y
+CONFIG_PHY=y
+CONFIG_PHY_MTK_TPHY=y
+CONFIG_DM_REGULATOR=y
CONFIG_DM_SERIAL=y
CONFIG_MTK_SERIAL=y
CONFIG_TIMER=y
@@ -33,3 +43,12 @@ CONFIG_MTK_TIMER=y
CONFIG_WDT=y
CONFIG_WDT_MTK=y
CONFIG_LZO=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_DM_USB_GADGET=y
+CONFIG_USB_MTU3=y
+CONFIG_USB_MTU3_GADGET=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="MediaTek"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0e8d
+CONFIG_USB_GADGET_PRODUCT_NUM=0x201c
--
1.9.1
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [PATCH next v7 09/10] configs: mt8512: add USB host related configs
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
` (7 preceding siblings ...)
2020-09-18 9:10 ` [PATCH next v7 08/10] configs: mt8512: enable fastboot Chunfeng Yun
@ 2020-09-18 9:10 ` Chunfeng Yun
2020-10-13 14:34 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 10/10] MAINTAINERS: add USB driver to ARM MEDIATEK Chunfeng Yun
2020-09-28 2:01 ` [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
10 siblings, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
Add USB, FAT commands, and fixed regulator, mass storage
drivers.
Due to device mode is enabled by default, comment out
the host mode config here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v5~v7: no changes
v4: new patch
---
configs/mt8512_bm1_emmc_defconfig | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/configs/mt8512_bm1_emmc_defconfig b/configs/mt8512_bm1_emmc_defconfig
index d41446f..6b5454c 100644
--- a/configs/mt8512_bm1_emmc_defconfig
+++ b/configs/mt8512_bm1_emmc_defconfig
@@ -15,6 +15,10 @@ CONFIG_DEFAULT_FDT_FILE="mt8512-bm1-emmc.dtb"
CONFIG_SYS_PROMPT="MT8512> "
CONFIG_CMD_BOOTMENU=y
CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+# CONFIG_DOS_PARTITION is not set
CONFIG_ENV_OVERWRITE=y
CONFIG_REGMAP=y
CONFIG_SYSCON=y
@@ -36,6 +40,7 @@ CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT=y
CONFIG_PHY=y
CONFIG_PHY_MTK_TPHY=y
CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_SERIAL=y
CONFIG_MTK_SERIAL=y
CONFIG_TIMER=y
@@ -48,6 +53,8 @@ CONFIG_DM_USB=y
CONFIG_DM_USB_GADGET=y
CONFIG_USB_MTU3=y
CONFIG_USB_MTU3_GADGET=y
+#CONFIG_USB_MTU3_HOST=y
+CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="MediaTek"
CONFIG_USB_GADGET_VENDOR_NUM=0x0e8d
--
1.9.1
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [PATCH next v7 10/10] MAINTAINERS: add USB driver to ARM MEDIATEK
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
` (8 preceding siblings ...)
2020-09-18 9:10 ` [PATCH next v7 09/10] configs: mt8512: add USB host related configs Chunfeng Yun
@ 2020-09-18 9:10 ` Chunfeng Yun
2020-10-13 14:35 ` Bin Meng
2020-09-28 2:01 ` [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
10 siblings, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-18 9:10 UTC (permalink / raw)
To: u-boot
Add MediaTek USB3 Dual-Role controller driver to ARM MEDIATEK,
and add myself as a maintainer for it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v6~v7: no changes
v5: add mtu3/, xhci-mtk.c, and myself as maintainer for MTK USB
v4: new patch
---
MAINTAINERS | 3 +++
1 file changed, 3 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 7e46470..08724f8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -262,6 +262,7 @@ F: arch/arm/include/asm/arch-pxa/
ARM MEDIATEK
M: Ryder Lee <ryder.lee@mediatek.com>
M: Weijie Gao <weijie.gao@mediatek.com>
+M: Chunfeng Yun <chunfeng.yun@mediatek.com>
R: GSS_MTK_Uboot_upstream <GSS_MTK_Uboot_upstream@mediatek.com>
S: Maintained
F: arch/arm/mach-mediatek/
@@ -278,6 +279,8 @@ F: drivers/power/domain/mtk-power-domain.c
F: drivers/ram/mediatek/
F: drivers/spi/mtk_snfi_spi.c
F: drivers/timer/mtk_timer.c
+F: drivers/usb/host/xhci-mtk.c
+F: drivers/usb/mtu3/
F: drivers/watchdog/mtk_wdt.c
F: drivers/net/mtk_eth.c
F: drivers/reset/reset-mediatek.c
--
1.9.1
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
` (9 preceding siblings ...)
2020-09-18 9:10 ` [PATCH next v7 10/10] MAINTAINERS: add USB driver to ARM MEDIATEK Chunfeng Yun
@ 2020-09-28 2:01 ` Chunfeng Yun
2020-09-28 2:12 ` Marek Vasut
10 siblings, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-28 2:01 UTC (permalink / raw)
To: u-boot
Hi Marek, Lukasz
Any comments on this patch series?
Thanks a lot
On Fri, 2020-09-18 at 17:10 +0800, Chunfeng Yun wrote:
> These patches introduce the MediaTek USB3 Dual-Role Controller
> driver.
> The driver can be configured as Peripheral only and Host only(xHCI)
> modes, and it's ported from Linux Kernel 5.8-rc1
>
> v7 changes
> 1. use xhci quirk flag XHCI_MTK_HOST
>
> v6 changes
> 1. modify commit message of [4/10]
>
> v5 changes:
> 1. change condition of readl_poll_timeout() when check clocks
> 2. add xhci-mtk.c and myself as maintainer for MTK USB
>
> v4 changes:
> 1. [4/10], [9/10] and [10/10] are new patches
> 2. add a glue driver
> 3. add host driver and rebuild host flow
> 4. support force_vbus mode for device
> 5. update bindings to support glue driver
>
> v3 changes:
> 1. add patch [5/7]
> 2. add udc_set_speed()
> 3. simplify some code flow
>
> v2 changes:
> 1. simplify QMU operations
>
> Chunfeng Yun (10):
> dt-binding: usb: add bindings for some common properties
> dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD
> usb: add USB_SPEED_SUPER_PLUS
> usb: common: add define of usb_speed_string()
> usb: add MediaTek USB3 DRD driver
> usb: gadget: Add bcdDevice for the MTU3 USB Gadget Controller
> arm: dts: mt8512: add usb related nodes
> configs: mt8512: enable fastboot
> configs: mt8512: add USB host related configs
> MAINTAINERS: add USB driver to ARM MEDIATEK
>
> MAINTAINERS | 3 +
> Makefile | 1 +
> arch/arm/dts/mt8512-bm1-emmc.dts | 34 +
> arch/arm/dts/mt8512.dtsi | 49 +-
> configs/mt8512_bm1_emmc_defconfig | 26 +
> doc/device-tree-bindings/usb/generic.txt | 31 +
> doc/device-tree-bindings/usb/mediatek,mtu3.txt | 79 +++
> drivers/usb/Kconfig | 2 +
> drivers/usb/common/common.c | 8 +
> drivers/usb/gadget/gadget_chips.h | 8 +
> drivers/usb/mtu3/Kconfig | 45 ++
> drivers/usb/mtu3/Makefile | 11 +
> drivers/usb/mtu3/mtu3.h | 423 +++++++++++
> drivers/usb/mtu3/mtu3_core.c | 838 ++++++++++++++++++++++
> drivers/usb/mtu3/mtu3_dr.h | 52 ++
> drivers/usb/mtu3/mtu3_gadget.c | 686 ++++++++++++++++++
> drivers/usb/mtu3/mtu3_gadget_ep0.c | 933 +++++++++++++++++++++++++
> drivers/usb/mtu3/mtu3_host.c | 141 ++++
> drivers/usb/mtu3/mtu3_hw_regs.h | 515 ++++++++++++++
> drivers/usb/mtu3/mtu3_plat.c | 368 ++++++++++
> drivers/usb/mtu3/mtu3_qmu.c | 504 +++++++++++++
> drivers/usb/mtu3/mtu3_qmu.h | 37 +
> include/linux/usb/ch9.h | 5 +-
> 23 files changed, 4794 insertions(+), 5 deletions(-)
> create mode 100644 doc/device-tree-bindings/usb/generic.txt
> create mode 100644 doc/device-tree-bindings/usb/mediatek,mtu3.txt
> create mode 100644 drivers/usb/mtu3/Kconfig
> create mode 100644 drivers/usb/mtu3/Makefile
> create mode 100644 drivers/usb/mtu3/mtu3.h
> create mode 100644 drivers/usb/mtu3/mtu3_core.c
> create mode 100644 drivers/usb/mtu3/mtu3_dr.h
> create mode 100644 drivers/usb/mtu3/mtu3_gadget.c
> create mode 100644 drivers/usb/mtu3/mtu3_gadget_ep0.c
> create mode 100644 drivers/usb/mtu3/mtu3_host.c
> create mode 100644 drivers/usb/mtu3/mtu3_hw_regs.h
> create mode 100644 drivers/usb/mtu3/mtu3_plat.c
> create mode 100644 drivers/usb/mtu3/mtu3_qmu.c
> create mode 100644 drivers/usb/mtu3/mtu3_qmu.h
>
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver
2020-09-28 2:01 ` [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
@ 2020-09-28 2:12 ` Marek Vasut
2020-09-28 2:20 ` Chunfeng Yun
2020-10-13 7:26 ` Chunfeng Yun
0 siblings, 2 replies; 29+ messages in thread
From: Marek Vasut @ 2020-09-28 2:12 UTC (permalink / raw)
To: u-boot
On 9/28/20 4:01 AM, Chunfeng Yun wrote:
[...]
>> create mode 100644 drivers/usb/mtu3/mtu3_core.c
>> create mode 100644 drivers/usb/mtu3/mtu3_dr.h
>> create mode 100644 drivers/usb/mtu3/mtu3_gadget.c
>> create mode 100644 drivers/usb/mtu3/mtu3_gadget_ep0.c
>> create mode 100644 drivers/usb/mtu3/mtu3_host.c
>> create mode 100644 drivers/usb/mtu3/mtu3_hw_regs.h
>> create mode 100644 drivers/usb/mtu3/mtu3_plat.c
>> create mode 100644 drivers/usb/mtu3/mtu3_qmu.c
>> create mode 100644 drivers/usb/mtu3/mtu3_qmu.h
Since this is USB3 driver, you want this reviewed by Bin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver
2020-09-28 2:12 ` Marek Vasut
@ 2020-09-28 2:20 ` Chunfeng Yun
2020-10-13 7:26 ` Chunfeng Yun
1 sibling, 0 replies; 29+ messages in thread
From: Chunfeng Yun @ 2020-09-28 2:20 UTC (permalink / raw)
To: u-boot
Hi Marek,
On Mon, 2020-09-28 at 04:12 +0200, Marek Vasut wrote:
> On 9/28/20 4:01 AM, Chunfeng Yun wrote:
> [...]
> >> create mode 100644 drivers/usb/mtu3/mtu3_core.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_dr.h
> >> create mode 100644 drivers/usb/mtu3/mtu3_gadget.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_gadget_ep0.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_host.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_hw_regs.h
> >> create mode 100644 drivers/usb/mtu3/mtu3_plat.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_qmu.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_qmu.h
>
> Since this is USB3 driver, you want this reviewed by Bin
Got it.
Hi Bin,
Would you please help to review this series?
Thank you Marek and Bin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver
2020-09-28 2:12 ` Marek Vasut
2020-09-28 2:20 ` Chunfeng Yun
@ 2020-10-13 7:26 ` Chunfeng Yun
2020-10-13 10:27 ` Bin Meng
1 sibling, 1 reply; 29+ messages in thread
From: Chunfeng Yun @ 2020-10-13 7:26 UTC (permalink / raw)
To: u-boot
Hi Bin,
Gentle ping...
Could you help to review this series?
Thanks a lot
On Mon, 2020-09-28 at 04:12 +0200, Marek Vasut wrote:
> On 9/28/20 4:01 AM, Chunfeng Yun wrote:
> [...]
> >> create mode 100644 drivers/usb/mtu3/mtu3_core.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_dr.h
> >> create mode 100644 drivers/usb/mtu3/mtu3_gadget.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_gadget_ep0.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_host.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_hw_regs.h
> >> create mode 100644 drivers/usb/mtu3/mtu3_plat.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_qmu.c
> >> create mode 100644 drivers/usb/mtu3/mtu3_qmu.h
>
> Since this is USB3 driver, you want this reviewed by Bin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver
2020-10-13 7:26 ` Chunfeng Yun
@ 2020-10-13 10:27 ` Bin Meng
0 siblings, 0 replies; 29+ messages in thread
From: Bin Meng @ 2020-10-13 10:27 UTC (permalink / raw)
To: u-boot
Hi Chunfeng,
On Tue, Oct 13, 2020 at 3:26 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
>
> Hi Bin,
>
> Gentle ping...
>
> Could you help to review this series?
Will have a look soon.
>
> Thanks a lot
>
>
> On Mon, 2020-09-28 at 04:12 +0200, Marek Vasut wrote:
> > On 9/28/20 4:01 AM, Chunfeng Yun wrote:
> > [...]
> > >> create mode 100644 drivers/usb/mtu3/mtu3_core.c
> > >> create mode 100644 drivers/usb/mtu3/mtu3_dr.h
> > >> create mode 100644 drivers/usb/mtu3/mtu3_gadget.c
> > >> create mode 100644 drivers/usb/mtu3/mtu3_gadget_ep0.c
> > >> create mode 100644 drivers/usb/mtu3/mtu3_host.c
> > >> create mode 100644 drivers/usb/mtu3/mtu3_hw_regs.h
> > >> create mode 100644 drivers/usb/mtu3/mtu3_plat.c
> > >> create mode 100644 drivers/usb/mtu3/mtu3_qmu.c
> > >> create mode 100644 drivers/usb/mtu3/mtu3_qmu.h
> >
> > Since this is USB3 driver, you want this reviewed by Bin
>
Regards,
Bin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 01/10] dt-binding: usb: add bindings for some common properties
2020-09-18 9:10 ` [PATCH next v7 01/10] dt-binding: usb: add bindings for some common properties Chunfeng Yun
@ 2020-10-13 14:15 ` Bin Meng
0 siblings, 0 replies; 29+ messages in thread
From: Bin Meng @ 2020-10-13 14:15 UTC (permalink / raw)
To: u-boot
On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
>
> Add bindings for common properties, include maximum-speed,
> dr_mode and phy_type
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2~v7: no changes
> ---
> doc/device-tree-bindings/usb/generic.txt | 31 +++++++++++++++++++++++++++++++
> 1 file changed, 31 insertions(+)
> create mode 100644 doc/device-tree-bindings/usb/generic.txt
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 02/10] dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD
2020-09-18 9:10 ` [PATCH next v7 02/10] dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD Chunfeng Yun
@ 2020-10-13 14:18 ` Bin Meng
2020-10-14 2:46 ` Chunfeng Yun
0 siblings, 1 reply; 29+ messages in thread
From: Bin Meng @ 2020-10-13 14:18 UTC (permalink / raw)
To: u-boot
On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
>
> Add dt-binding for MediaTek USB3 DRD Driver
There are some differences compared to the one in the Linux kernel:
https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/usb/mediatek%2Cmtu3.txt
Please specify which kernel commit id the device bindings are referenced here.
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v5~v7: no changes
>
> v4:
> Add support host mode, introduce some new properties and subnode
>
> v2~v3: no changes
> ---
> doc/device-tree-bindings/usb/mediatek,mtu3.txt | 79 ++++++++++++++++++++++++++
> 1 file changed, 79 insertions(+)
> create mode 100644 doc/device-tree-bindings/usb/mediatek,mtu3.txt
>
Regards,
Bin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 03/10] usb: add USB_SPEED_SUPER_PLUS
2020-09-18 9:10 ` [PATCH next v7 03/10] usb: add USB_SPEED_SUPER_PLUS Chunfeng Yun
@ 2020-10-13 14:19 ` Bin Meng
2020-10-14 2:50 ` Chunfeng Yun
0 siblings, 1 reply; 29+ messages in thread
From: Bin Meng @ 2020-10-13 14:19 UTC (permalink / raw)
To: u-boot
On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
>
> Add enum USB_SPEED_SUPER_PLUS for USB3.1
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v5~v7: no changes
>
> v4: also add it into speed_names array
>
> v2~v3: no changes
> ---
> drivers/usb/common/common.c | 1 +
> include/linux/usb/ch9.h | 1 +
> 2 files changed, 2 insertions(+)
>
> diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
> index d4ae186..76f5a9c 100644
> --- a/drivers/usb/common/common.c
> +++ b/drivers/usb/common/common.c
> @@ -46,6 +46,7 @@ static const char *const speed_names[] = {
> [USB_SPEED_HIGH] = "high-speed",
> [USB_SPEED_WIRELESS] = "wireless",
> [USB_SPEED_SUPER] = "super-speed",
> + [USB_SPEED_SUPER_PLUS] = "super-speed-plus",
> };
>
> enum usb_device_speed usb_get_maximum_speed(ofnode node)
> diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
> index 989a5fc..7d225ee 100644
> --- a/include/linux/usb/ch9.h
> +++ b/include/linux/usb/ch9.h
> @@ -956,6 +956,7 @@ enum usb_device_speed {
> USB_SPEED_HIGH, /* usb 2.0 */
> USB_SPEED_WIRELESS, /* wireless (usb 2.5) */
> USB_SPEED_SUPER, /* usb 3.0 */
> + USB_SPEED_SUPER_PLUS, /* usb 3.1 */
> };
>
> #ifdef __KERNEL__
Should we add usb 3.2 as well?
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 04/10] usb: common: add define of usb_speed_string()
2020-09-18 9:10 ` [PATCH next v7 04/10] usb: common: add define of usb_speed_string() Chunfeng Yun
@ 2020-10-13 14:21 ` Bin Meng
0 siblings, 0 replies; 29+ messages in thread
From: Bin Meng @ 2020-10-13 14:21 UTC (permalink / raw)
To: u-boot
On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
>
> There is only declaration of usb_speed_string(), but no definition,
> so add it to avoid build error when call it.
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v7: no changes
>
> v6: modify commit message suggested by Roger
>
> v5: no changes
>
> v4: new patch
> ---
> drivers/usb/common/common.c | 7 +++++++
> include/linux/usb/ch9.h | 4 ----
> 2 files changed, 7 insertions(+), 4 deletions(-)
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 05/10] usb: add MediaTek USB3 DRD driver
2020-09-18 9:10 ` [PATCH next v7 05/10] usb: add MediaTek USB3 DRD driver Chunfeng Yun
@ 2020-10-13 14:26 ` Bin Meng
2020-10-14 3:15 ` Chunfeng Yun
0 siblings, 1 reply; 29+ messages in thread
From: Bin Meng @ 2020-10-13 14:26 UTC (permalink / raw)
To: u-boot
On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
>
> This patch adds support for the MediaTek USB3 DRD controller,
> its host side is based on xHCI, this driver supports device mode
> and host mode.
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
I can only comment some generic stuff, since I have no access to the
controller datasheet.
> ---
> v7:
> 1. use xhci quirk flag XHCI_MTK_HOST
>
> v6: no changes
>
> v5:
> 1. change condition of readl_poll_timeout() when check clocks
>
> v4:
> 1. remove unused member @busy and @wedged, use their flags instead
> 2. support force_vbus mode
> 3. add a glue driver using UCLASS_NOP
> 4. add host driver, and rebuild host flow
>
> v3 changes
> 1. add ->udc_set_speed()
> 2. simplify some code flow
>
> v2: simplify QMU operations
> ---
> Makefile | 1 +
> drivers/usb/Kconfig | 2 +
> drivers/usb/mtu3/Kconfig | 45 ++
> drivers/usb/mtu3/Makefile | 11 +
> drivers/usb/mtu3/mtu3.h | 423 +++++++++++++++++
> drivers/usb/mtu3/mtu3_core.c | 838 +++++++++++++++++++++++++++++++++
> drivers/usb/mtu3/mtu3_dr.h | 52 +++
> drivers/usb/mtu3/mtu3_gadget.c | 686 +++++++++++++++++++++++++++
> drivers/usb/mtu3/mtu3_gadget_ep0.c | 933 +++++++++++++++++++++++++++++++++++++
> drivers/usb/mtu3/mtu3_host.c | 141 ++++++
> drivers/usb/mtu3/mtu3_hw_regs.h | 515 ++++++++++++++++++++
> drivers/usb/mtu3/mtu3_plat.c | 368 +++++++++++++++
> drivers/usb/mtu3/mtu3_qmu.c | 504 ++++++++++++++++++++
> drivers/usb/mtu3/mtu3_qmu.h | 37 ++
> 14 files changed, 4556 insertions(+)
> create mode 100644 drivers/usb/mtu3/Kconfig
> create mode 100644 drivers/usb/mtu3/Makefile
> create mode 100644 drivers/usb/mtu3/mtu3.h
> create mode 100644 drivers/usb/mtu3/mtu3_core.c
> create mode 100644 drivers/usb/mtu3/mtu3_dr.h
> create mode 100644 drivers/usb/mtu3/mtu3_gadget.c
> create mode 100644 drivers/usb/mtu3/mtu3_gadget_ep0.c
> create mode 100644 drivers/usb/mtu3/mtu3_host.c
> create mode 100644 drivers/usb/mtu3/mtu3_hw_regs.h
> create mode 100644 drivers/usb/mtu3/mtu3_plat.c
> create mode 100644 drivers/usb/mtu3/mtu3_qmu.c
> create mode 100644 drivers/usb/mtu3/mtu3_qmu.h
>
> diff --git a/Makefile b/Makefile
> index 7a05fc7..2dcc41a 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -795,6 +795,7 @@ libs-y += drivers/usb/eth/
> libs-$(CONFIG_USB_GADGET) += drivers/usb/gadget/
> libs-$(CONFIG_USB_GADGET) += drivers/usb/gadget/udc/
> libs-y += drivers/usb/host/
> +libs-y += drivers/usb/mtu3/
> libs-y += drivers/usb/musb/
> libs-y += drivers/usb/musb-new/
> libs-y += drivers/usb/phy/
> diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
> index 34881a1..fedc013 100644
> --- a/drivers/usb/Kconfig
> +++ b/drivers/usb/Kconfig
> @@ -72,6 +72,8 @@ source "drivers/usb/cdns3/Kconfig"
>
> source "drivers/usb/dwc3/Kconfig"
>
> +source "drivers/usb/mtu3/Kconfig"
> +
> source "drivers/usb/musb/Kconfig"
>
> source "drivers/usb/musb-new/Kconfig"
> diff --git a/drivers/usb/mtu3/Kconfig b/drivers/usb/mtu3/Kconfig
> new file mode 100644
> index 0000000..66651ad
> --- /dev/null
> +++ b/drivers/usb/mtu3/Kconfig
> @@ -0,0 +1,45 @@
> +# SPDX-License-Identifier: GPL-2.0
> +#
> +# For MTK USB3.0 IP
> +
> +config USB_MTU3
> + bool "MediaTek USB3 Dual Role controller"
> + depends on USB || USB_GADGET
> + depends on ARCH_MEDIATEK
> + help
> + Say Y here if your system runs on MediaTek SoCs with
> + Dual Role SuperSpeed USB controller. You can select usb
> + mode as peripheral role or host role.
> +
> + If you don't know what this is, please say N.
> +
> +if USB_MTU3
> +choice
> + bool "MTU3 Mode Selection"
> + default USB_MTU3_GADGET if USB_GADGET
> + default USB_MTU3_HOST if (USB && !USB_GADGET)
> +
> +config USB_MTU3_HOST
> + bool "Host only mode"
> + depends on USB=y || USB=USB_MTU3
Is this Kconfig grammer supported by U-Boot?
> + select USB_XHCI_HCD
> + help
> + Select this when you want to use MTU3 in host mode only,
> + thereby the gadget feature will be regressed.
> +
> +config USB_MTU3_GADGET
> + bool "Gadget only mode"
> + depends on USB_GADGET=y || USB_GADGET=USB_MTU3
> + select USB_GADGET_DUALSPEED
> + help
> + Select this when you want to use MTU3 in gadget mode only,
> + thereby the host feature will be regressed.
> +
> +endchoice
> +
> +config USB_MTU3_DEBUG
> + bool "Enable Debugging Messages"
> + help
> + Say Y here to enable debugging messages in the MTU3 Driver.
> +
> +endif
> diff --git a/drivers/usb/mtu3/Makefile b/drivers/usb/mtu3/Makefile
> new file mode 100644
> index 0000000..234f3a3
> --- /dev/null
> +++ b/drivers/usb/mtu3/Makefile
> @@ -0,0 +1,11 @@
> +# SPDX-License-Identifier: GPL-2.0
> +
> +ccflags-$(CONFIG_USB_MTU3_DEBUG) += -DDEBUG
> +
> +obj-$(CONFIG_USB_MTU3) += mtu3.o
> +
> +mtu3-y := mtu3_plat.o
> +
> +obj-$(CONFIG_USB_MTU3_GADGET) += mtu3_core.o mtu3_gadget_ep0.o mtu3_gadget.o
> +obj-$(CONFIG_USB_MTU3_GADGET) += mtu3_qmu.o
> +obj-$(CONFIG_USB_MTU3_HOST) += mtu3_host.o
[snip]
Regards,
Bin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 06/10] usb: gadget: Add bcdDevice for the MTU3 USB Gadget Controller
2020-09-18 9:10 ` [PATCH next v7 06/10] usb: gadget: Add bcdDevice for the MTU3 USB Gadget Controller Chunfeng Yun
@ 2020-10-13 14:28 ` Bin Meng
0 siblings, 0 replies; 29+ messages in thread
From: Bin Meng @ 2020-10-13 14:28 UTC (permalink / raw)
To: u-boot
On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
>
> Add an entry in usb_gadget_controller_number() for the MTU3
> gadget controller. It is used to bind the USB Ethernet driver.
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v4~v7: no changes
>
> v3: new patch
> ---
> drivers/usb/gadget/gadget_chips.h | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 07/10] arm: dts: mt8512: add usb related nodes
2020-09-18 9:10 ` [PATCH next v7 07/10] arm: dts: mt8512: add usb related nodes Chunfeng Yun
@ 2020-10-13 14:32 ` Bin Meng
0 siblings, 0 replies; 29+ messages in thread
From: Bin Meng @ 2020-10-13 14:32 UTC (permalink / raw)
To: u-boot
On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
>
> Add usb, usb phy, and fixed regulators nodes
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v5~v7: no changes
>
> v4: add host related properties, add subnode.
>
> v3: remove unused property mediatek,discth
>
> v2: no changes
> ---
> arch/arm/dts/mt8512-bm1-emmc.dts | 34 ++++++++++++++++++++++++++++
> arch/arm/dts/mt8512.dtsi | 49 +++++++++++++++++++++++++++++++++++++++-
> 2 files changed, 82 insertions(+), 1 deletion(-)
>
LGTM
Acked-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 09/10] configs: mt8512: add USB host related configs
2020-09-18 9:10 ` [PATCH next v7 09/10] configs: mt8512: add USB host related configs Chunfeng Yun
@ 2020-10-13 14:34 ` Bin Meng
2020-10-14 3:40 ` Chunfeng Yun
0 siblings, 1 reply; 29+ messages in thread
From: Bin Meng @ 2020-10-13 14:34 UTC (permalink / raw)
To: u-boot
On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
>
> Add USB, FAT commands, and fixed regulator, mass storage
> drivers.
> Due to device mode is enabled by default, comment out
> the host mode config here.
This patch should be squashed into patch [08/10]
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v5~v7: no changes
>
> v4: new patch
> ---
> configs/mt8512_bm1_emmc_defconfig | 7 +++++++
> 1 file changed, 7 insertions(+)
>
> diff --git a/configs/mt8512_bm1_emmc_defconfig b/configs/mt8512_bm1_emmc_defconfig
> index d41446f..6b5454c 100644
> --- a/configs/mt8512_bm1_emmc_defconfig
> +++ b/configs/mt8512_bm1_emmc_defconfig
> @@ -15,6 +15,10 @@ CONFIG_DEFAULT_FDT_FILE="mt8512-bm1-emmc.dtb"
> CONFIG_SYS_PROMPT="MT8512> "
> CONFIG_CMD_BOOTMENU=y
> CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_FAT=y
> +CONFIG_CMD_FS_GENERIC=y
> +# CONFIG_DOS_PARTITION is not set
> CONFIG_ENV_OVERWRITE=y
> CONFIG_REGMAP=y
> CONFIG_SYSCON=y
> @@ -36,6 +40,7 @@ CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT=y
> CONFIG_PHY=y
> CONFIG_PHY_MTK_TPHY=y
> CONFIG_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> CONFIG_DM_SERIAL=y
> CONFIG_MTK_SERIAL=y
> CONFIG_TIMER=y
> @@ -48,6 +53,8 @@ CONFIG_DM_USB=y
> CONFIG_DM_USB_GADGET=y
> CONFIG_USB_MTU3=y
> CONFIG_USB_MTU3_GADGET=y
> +#CONFIG_USB_MTU3_HOST=y
This should be :
# CONFIG_USB_MTU3_HOST is not set
> +CONFIG_USB_STORAGE=y
> CONFIG_USB_GADGET=y
> CONFIG_USB_GADGET_MANUFACTURER="MediaTek"
> CONFIG_USB_GADGET_VENDOR_NUM=0x0e8d
> --
Regards,
Bin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 10/10] MAINTAINERS: add USB driver to ARM MEDIATEK
2020-09-18 9:10 ` [PATCH next v7 10/10] MAINTAINERS: add USB driver to ARM MEDIATEK Chunfeng Yun
@ 2020-10-13 14:35 ` Bin Meng
0 siblings, 0 replies; 29+ messages in thread
From: Bin Meng @ 2020-10-13 14:35 UTC (permalink / raw)
To: u-boot
On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
>
> Add MediaTek USB3 Dual-Role controller driver to ARM MEDIATEK,
> and add myself as a maintainer for it.
>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v6~v7: no changes
>
> v5: add mtu3/, xhci-mtk.c, and myself as maintainer for MTK USB
>
> v4: new patch
> ---
> MAINTAINERS | 3 +++
> 1 file changed, 3 insertions(+)
>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 02/10] dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD
2020-10-13 14:18 ` Bin Meng
@ 2020-10-14 2:46 ` Chunfeng Yun
0 siblings, 0 replies; 29+ messages in thread
From: Chunfeng Yun @ 2020-10-14 2:46 UTC (permalink / raw)
To: u-boot
On Tue, 2020-10-13 at 22:18 +0800, Bin Meng wrote:
> On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
> >
> > Add dt-binding for MediaTek USB3 DRD Driver
>
> There are some differences compared to the one in the Linux kernel:
Some properties are removed due to dual-role switch is not supported in
Uboot.
> https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/usb/mediatek%2Cmtu3.txt
>
> Please specify which kernel commit id the device bindings are referenced here.
Ok, will add it in next version
Thanks
>
> >
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > v5~v7: no changes
> >
> > v4:
> > Add support host mode, introduce some new properties and subnode
> >
> > v2~v3: no changes
> > ---
> > doc/device-tree-bindings/usb/mediatek,mtu3.txt | 79 ++++++++++++++++++++++++++
> > 1 file changed, 79 insertions(+)
> > create mode 100644 doc/device-tree-bindings/usb/mediatek,mtu3.txt
> >
>
> Regards,
> Bin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 03/10] usb: add USB_SPEED_SUPER_PLUS
2020-10-13 14:19 ` Bin Meng
@ 2020-10-14 2:50 ` Chunfeng Yun
0 siblings, 0 replies; 29+ messages in thread
From: Chunfeng Yun @ 2020-10-14 2:50 UTC (permalink / raw)
To: u-boot
On Tue, 2020-10-13 at 22:19 +0800, Bin Meng wrote:
> On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
> >
> > Add enum USB_SPEED_SUPER_PLUS for USB3.1
> >
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > v5~v7: no changes
> >
> > v4: also add it into speed_names array
> >
> > v2~v3: no changes
> > ---
> > drivers/usb/common/common.c | 1 +
> > include/linux/usb/ch9.h | 1 +
> > 2 files changed, 2 insertions(+)
> >
> > diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
> > index d4ae186..76f5a9c 100644
> > --- a/drivers/usb/common/common.c
> > +++ b/drivers/usb/common/common.c
> > @@ -46,6 +46,7 @@ static const char *const speed_names[] = {
> > [USB_SPEED_HIGH] = "high-speed",
> > [USB_SPEED_WIRELESS] = "wireless",
> > [USB_SPEED_SUPER] = "super-speed",
> > + [USB_SPEED_SUPER_PLUS] = "super-speed-plus",
> > };
> >
> > enum usb_device_speed usb_get_maximum_speed(ofnode node)
> > diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
> > index 989a5fc..7d225ee 100644
> > --- a/include/linux/usb/ch9.h
> > +++ b/include/linux/usb/ch9.h
> > @@ -956,6 +956,7 @@ enum usb_device_speed {
> > USB_SPEED_HIGH, /* usb 2.0 */
> > USB_SPEED_WIRELESS, /* wireless (usb 2.5) */
> > USB_SPEED_SUPER, /* usb 3.0 */
> > + USB_SPEED_SUPER_PLUS, /* usb 3.1 */
> > };
> >
> > #ifdef __KERNEL__
>
> Should we add usb 3.2 as well?
I found the patches to support USB3.2 are still in public review for
Linux kernel, so no need support it currently
>
> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 05/10] usb: add MediaTek USB3 DRD driver
2020-10-13 14:26 ` Bin Meng
@ 2020-10-14 3:15 ` Chunfeng Yun
0 siblings, 0 replies; 29+ messages in thread
From: Chunfeng Yun @ 2020-10-14 3:15 UTC (permalink / raw)
To: u-boot
On Tue, 2020-10-13 at 22:26 +0800, Bin Meng wrote:
> On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
> >
> > This patch adds support for the MediaTek USB3 DRD controller,
> > its host side is based on xHCI, this driver supports device mode
> > and host mode.
> >
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
>
> I can only comment some generic stuff, since I have no access to the
> controller datasheet.
It's good enough, I and my workmate will test the function
>
> > ---
> > v7:
> > 1. use xhci quirk flag XHCI_MTK_HOST
> >
> > v6: no changes
> >
> > v5:
> > 1. change condition of readl_poll_timeout() when check clocks
> >
> > v4:
> > 1. remove unused member @busy and @wedged, use their flags instead
> > 2. support force_vbus mode
> > 3. add a glue driver using UCLASS_NOP
> > 4. add host driver, and rebuild host flow
> >
> > v3 changes
> > 1. add ->udc_set_speed()
> > 2. simplify some code flow
> >
> > v2: simplify QMU operations
> > ---
> > Makefile | 1 +
> > drivers/usb/Kconfig | 2 +
> > drivers/usb/mtu3/Kconfig | 45 ++
> > drivers/usb/mtu3/Makefile | 11 +
> > drivers/usb/mtu3/mtu3.h | 423 +++++++++++++++++
> > drivers/usb/mtu3/mtu3_core.c | 838 +++++++++++++++++++++++++++++++++
> > drivers/usb/mtu3/mtu3_dr.h | 52 +++
> > drivers/usb/mtu3/mtu3_gadget.c | 686 +++++++++++++++++++++++++++
> > drivers/usb/mtu3/mtu3_gadget_ep0.c | 933 +++++++++++++++++++++++++++++++++++++
> > drivers/usb/mtu3/mtu3_host.c | 141 ++++++
> > drivers/usb/mtu3/mtu3_hw_regs.h | 515 ++++++++++++++++++++
> > drivers/usb/mtu3/mtu3_plat.c | 368 +++++++++++++++
> > drivers/usb/mtu3/mtu3_qmu.c | 504 ++++++++++++++++++++
> > drivers/usb/mtu3/mtu3_qmu.h | 37 ++
> > 14 files changed, 4556 insertions(+)
> > create mode 100644 drivers/usb/mtu3/Kconfig
> > create mode 100644 drivers/usb/mtu3/Makefile
> > create mode 100644 drivers/usb/mtu3/mtu3.h
> > create mode 100644 drivers/usb/mtu3/mtu3_core.c
> > create mode 100644 drivers/usb/mtu3/mtu3_dr.h
> > create mode 100644 drivers/usb/mtu3/mtu3_gadget.c
> > create mode 100644 drivers/usb/mtu3/mtu3_gadget_ep0.c
> > create mode 100644 drivers/usb/mtu3/mtu3_host.c
> > create mode 100644 drivers/usb/mtu3/mtu3_hw_regs.h
> > create mode 100644 drivers/usb/mtu3/mtu3_plat.c
> > create mode 100644 drivers/usb/mtu3/mtu3_qmu.c
> > create mode 100644 drivers/usb/mtu3/mtu3_qmu.h
> >
> > diff --git a/Makefile b/Makefile
> > index 7a05fc7..2dcc41a 100644
> > --- a/Makefile
> > +++ b/Makefile
> > @@ -795,6 +795,7 @@ libs-y += drivers/usb/eth/
> > libs-$(CONFIG_USB_GADGET) += drivers/usb/gadget/
> > libs-$(CONFIG_USB_GADGET) += drivers/usb/gadget/udc/
> > libs-y += drivers/usb/host/
> > +libs-y += drivers/usb/mtu3/
> > libs-y += drivers/usb/musb/
> > libs-y += drivers/usb/musb-new/
> > libs-y += drivers/usb/phy/
> > diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
> > index 34881a1..fedc013 100644
> > --- a/drivers/usb/Kconfig
> > +++ b/drivers/usb/Kconfig
> > @@ -72,6 +72,8 @@ source "drivers/usb/cdns3/Kconfig"
> >
> > source "drivers/usb/dwc3/Kconfig"
> >
> > +source "drivers/usb/mtu3/Kconfig"
> > +
> > source "drivers/usb/musb/Kconfig"
> >
> > source "drivers/usb/musb-new/Kconfig"
> > diff --git a/drivers/usb/mtu3/Kconfig b/drivers/usb/mtu3/Kconfig
> > new file mode 100644
> > index 0000000..66651ad
> > --- /dev/null
> > +++ b/drivers/usb/mtu3/Kconfig
> > @@ -0,0 +1,45 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +#
> > +# For MTK USB3.0 IP
> > +
> > +config USB_MTU3
> > + bool "MediaTek USB3 Dual Role controller"
> > + depends on USB || USB_GADGET
> > + depends on ARCH_MEDIATEK
> > + help
> > + Say Y here if your system runs on MediaTek SoCs with
> > + Dual Role SuperSpeed USB controller. You can select usb
> > + mode as peripheral role or host role.
> > +
> > + If you don't know what this is, please say N.
> > +
> > +if USB_MTU3
> > +choice
> > + bool "MTU3 Mode Selection"
> > + default USB_MTU3_GADGET if USB_GADGET
> > + default USB_MTU3_HOST if (USB && !USB_GADGET)
> > +
> > +config USB_MTU3_HOST
> > + bool "Host only mode"
> > + depends on USB=y || USB=USB_MTU3
>
> Is this Kconfig grammer supported by U-Boot?
Yes, no error happens when use menuconfig, but can be simplified,
I modify it.
Thanks a lot
>
> > + select USB_XHCI_HCD
> > + help
> > + Select this when you want to use MTU3 in host mode only,
> > + thereby the gadget feature will be regressed.
> > +
> > +config USB_MTU3_GADGET
> > + bool "Gadget only mode"
> > + depends on USB_GADGET=y || USB_GADGET=USB_MTU3
> > + select USB_GADGET_DUALSPEED
> > + help
> > + Select this when you want to use MTU3 in gadget mode only,
> > + thereby the host feature will be regressed.
> > +
> > +endchoice
> > +
> > +config USB_MTU3_DEBUG
> > + bool "Enable Debugging Messages"
> > + help
> > + Say Y here to enable debugging messages in the MTU3 Driver.
> > +
> > +endif
> > diff --git a/drivers/usb/mtu3/Makefile b/drivers/usb/mtu3/Makefile
> > new file mode 100644
> > index 0000000..234f3a3
> > --- /dev/null
> > +++ b/drivers/usb/mtu3/Makefile
> > @@ -0,0 +1,11 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +
> > +ccflags-$(CONFIG_USB_MTU3_DEBUG) += -DDEBUG
> > +
> > +obj-$(CONFIG_USB_MTU3) += mtu3.o
> > +
> > +mtu3-y := mtu3_plat.o
> > +
> > +obj-$(CONFIG_USB_MTU3_GADGET) += mtu3_core.o mtu3_gadget_ep0.o mtu3_gadget.o
> > +obj-$(CONFIG_USB_MTU3_GADGET) += mtu3_qmu.o
> > +obj-$(CONFIG_USB_MTU3_HOST) += mtu3_host.o
>
> [snip]
>
> Regards,
> Bin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [PATCH next v7 09/10] configs: mt8512: add USB host related configs
2020-10-13 14:34 ` Bin Meng
@ 2020-10-14 3:40 ` Chunfeng Yun
0 siblings, 0 replies; 29+ messages in thread
From: Chunfeng Yun @ 2020-10-14 3:40 UTC (permalink / raw)
To: u-boot
On Tue, 2020-10-13 at 22:34 +0800, Bin Meng wrote:
> On Fri, Sep 18, 2020 at 5:12 PM Chunfeng Yun <chunfeng.yun@mediatek.com> wrote:
> >
> > Add USB, FAT commands, and fixed regulator, mass storage
> > drivers.
> > Due to device mode is enabled by default, comment out
> > the host mode config here.
>
> This patch should be squashed into patch [08/10]
Ok
>
> >
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > v5~v7: no changes
> >
> > v4: new patch
> > ---
> > configs/mt8512_bm1_emmc_defconfig | 7 +++++++
> > 1 file changed, 7 insertions(+)
> >
> > diff --git a/configs/mt8512_bm1_emmc_defconfig b/configs/mt8512_bm1_emmc_defconfig
> > index d41446f..6b5454c 100644
> > --- a/configs/mt8512_bm1_emmc_defconfig
> > +++ b/configs/mt8512_bm1_emmc_defconfig
> > @@ -15,6 +15,10 @@ CONFIG_DEFAULT_FDT_FILE="mt8512-bm1-emmc.dtb"
> > CONFIG_SYS_PROMPT="MT8512> "
> > CONFIG_CMD_BOOTMENU=y
> > CONFIG_CMD_MMC=y
> > +CONFIG_CMD_USB=y
> > +CONFIG_CMD_FAT=y
> > +CONFIG_CMD_FS_GENERIC=y
> > +# CONFIG_DOS_PARTITION is not set
> > CONFIG_ENV_OVERWRITE=y
> > CONFIG_REGMAP=y
> > CONFIG_SYSCON=y
> > @@ -36,6 +40,7 @@ CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT=y
> > CONFIG_PHY=y
> > CONFIG_PHY_MTK_TPHY=y
> > CONFIG_DM_REGULATOR=y
> > +CONFIG_DM_REGULATOR_FIXED=y
> > CONFIG_DM_SERIAL=y
> > CONFIG_MTK_SERIAL=y
> > CONFIG_TIMER=y
> > @@ -48,6 +53,8 @@ CONFIG_DM_USB=y
> > CONFIG_DM_USB_GADGET=y
> > CONFIG_USB_MTU3=y
> > CONFIG_USB_MTU3_GADGET=y
> > +#CONFIG_USB_MTU3_HOST=y
>
> This should be :
>
> # CONFIG_USB_MTU3_HOST is not set
Will modify it.
Thanks a lot
>
> > +CONFIG_USB_STORAGE=y
> > CONFIG_USB_GADGET=y
> > CONFIG_USB_GADGET_MANUFACTURER="MediaTek"
> > CONFIG_USB_GADGET_VENDOR_NUM=0x0e8d
> > --
>
> Regards,
> Bin
^ permalink raw reply [flat|nested] 29+ messages in thread
end of thread, other threads:[~2020-10-14 3:40 UTC | newest]
Thread overview: 29+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-09-18 9:10 [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 01/10] dt-binding: usb: add bindings for some common properties Chunfeng Yun
2020-10-13 14:15 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 02/10] dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD Chunfeng Yun
2020-10-13 14:18 ` Bin Meng
2020-10-14 2:46 ` Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 03/10] usb: add USB_SPEED_SUPER_PLUS Chunfeng Yun
2020-10-13 14:19 ` Bin Meng
2020-10-14 2:50 ` Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 04/10] usb: common: add define of usb_speed_string() Chunfeng Yun
2020-10-13 14:21 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 05/10] usb: add MediaTek USB3 DRD driver Chunfeng Yun
2020-10-13 14:26 ` Bin Meng
2020-10-14 3:15 ` Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 06/10] usb: gadget: Add bcdDevice for the MTU3 USB Gadget Controller Chunfeng Yun
2020-10-13 14:28 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 07/10] arm: dts: mt8512: add usb related nodes Chunfeng Yun
2020-10-13 14:32 ` Bin Meng
2020-09-18 9:10 ` [PATCH next v7 08/10] configs: mt8512: enable fastboot Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 09/10] configs: mt8512: add USB host related configs Chunfeng Yun
2020-10-13 14:34 ` Bin Meng
2020-10-14 3:40 ` Chunfeng Yun
2020-09-18 9:10 ` [PATCH next v7 10/10] MAINTAINERS: add USB driver to ARM MEDIATEK Chunfeng Yun
2020-10-13 14:35 ` Bin Meng
2020-09-28 2:01 ` [PATCH next v7 00/10] Add support MediaTek USB3 DRD driver Chunfeng Yun
2020-09-28 2:12 ` Marek Vasut
2020-09-28 2:20 ` Chunfeng Yun
2020-10-13 7:26 ` Chunfeng Yun
2020-10-13 10:27 ` Bin Meng
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.