* [PATCH v7 00/15] Add support for DP-HDMI2.1 PCON
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
This patch series attempts to add support for a DP-HDMI2.1 Protocol
Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
E5 to DisplayPort_v2.0:
https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
The details are mentioned in:
VESA DP-to-HDMI PCON Specification Standalone Document
https://groups.vesa.org/wg/DP/document/15651
This series starts with adding support for FRL (Fixed Rate Link)
Training between the PCON and HDMI2.1 sink.
As per HDMI2.1 specification, a new data-channel or lane is added in
FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
lanes).
With these patches, the HDMI2.1 PCON can be configured to achieve FRL
training based on the maximum FRL rate supported by the panel, source
and the PCON.
The approach is to add the support for FRL training between PCON and
HDMI2.1 sink and gradually add other blocks for supporting higher
resolutions and other HDMI2.1 features, that can be supported by pcon
for the sources that do not natively support HDMI2.1.
This is done before the DP Link training between the source and PCON
is started. In case of FRL training is not achieved, the PCON will
work in the regular TMDS mode, without HDMI2.1 feature support.
Any interruption in FRL training between the PCON and HDMI2.1 sink is
notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
registers are read and FRL training is re-attempted.
Currently, we have tested the FRL training and are able to enable 4K
display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
panel.
v2: Addressed review comments and re-organized patches as suggested in
comments on RFC patches.
v3: Addressed review comments on previous version.
v4: Added support for RGB->YCBCR conversion through PCON
v5: Addressed review comments on previous version.
v6: Fix typo in one of the patch.
v7: Rebased on latest drm-tip and addressed the review comments.
Ankit Nautiyal (11):
drm/edid: Parse DSC1.2 cap fields from HFVSDB block
drm/dp_helper: Add Helpers for FRL Link Training support for
DP-HDMI2.1 PCON
drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon
drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion
drm/i915: Capture max frl rate for PCON in dfp cap structure
drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
drm/i915: Check for FRL training before DP Link training
drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
drm/i915: Add helper functions for calculating DSC parameters for
HDMI2.1
drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
drm/i915/display: Let PCON convert from RGB to YCbCr if it can
Swati Sharma (4):
drm/edid: Add additional HFVSDB fields for HDMI2.1
drm/edid: Parse MAX_FRL field from HFVSDB block
drm/dp_helper: Add support for link failure detection
drm/i915: Add support for enabling link status and recovery
drivers/gpu/drm/drm_dp_helper.c | 566 ++++++++++++++++++
drivers/gpu/drm/drm_edid.c | 103 ++++
drivers/gpu/drm/i915/display/intel_ddi.c | 6 +-
.../drm/i915/display/intel_display_types.h | 10 +
drivers/gpu/drm/i915/display/intel_dp.c | 442 +++++++++++++-
drivers/gpu/drm/i915/display/intel_dp.h | 7 +-
drivers/gpu/drm/i915/display/intel_hdmi.c | 233 +++++++
drivers/gpu/drm/i915/display/intel_hdmi.h | 7 +
include/drm/drm_connector.h | 49 ++
include/drm/drm_dp_helper.h | 218 +++++++
include/drm/drm_edid.h | 30 +
11 files changed, 1652 insertions(+), 19 deletions(-)
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 00/15] Add support for DP-HDMI2.1 PCON
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
This patch series attempts to add support for a DP-HDMI2.1 Protocol
Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
E5 to DisplayPort_v2.0:
https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
The details are mentioned in:
VESA DP-to-HDMI PCON Specification Standalone Document
https://groups.vesa.org/wg/DP/document/15651
This series starts with adding support for FRL (Fixed Rate Link)
Training between the PCON and HDMI2.1 sink.
As per HDMI2.1 specification, a new data-channel or lane is added in
FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
lanes).
With these patches, the HDMI2.1 PCON can be configured to achieve FRL
training based on the maximum FRL rate supported by the panel, source
and the PCON.
The approach is to add the support for FRL training between PCON and
HDMI2.1 sink and gradually add other blocks for supporting higher
resolutions and other HDMI2.1 features, that can be supported by pcon
for the sources that do not natively support HDMI2.1.
This is done before the DP Link training between the source and PCON
is started. In case of FRL training is not achieved, the PCON will
work in the regular TMDS mode, without HDMI2.1 feature support.
Any interruption in FRL training between the PCON and HDMI2.1 sink is
notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
registers are read and FRL training is re-attempted.
Currently, we have tested the FRL training and are able to enable 4K
display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
panel.
v2: Addressed review comments and re-organized patches as suggested in
comments on RFC patches.
v3: Addressed review comments on previous version.
v4: Added support for RGB->YCBCR conversion through PCON
v5: Addressed review comments on previous version.
v6: Fix typo in one of the patch.
v7: Rebased on latest drm-tip and addressed the review comments.
Ankit Nautiyal (11):
drm/edid: Parse DSC1.2 cap fields from HFVSDB block
drm/dp_helper: Add Helpers for FRL Link Training support for
DP-HDMI2.1 PCON
drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon
drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion
drm/i915: Capture max frl rate for PCON in dfp cap structure
drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
drm/i915: Check for FRL training before DP Link training
drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
drm/i915: Add helper functions for calculating DSC parameters for
HDMI2.1
drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
drm/i915/display: Let PCON convert from RGB to YCbCr if it can
Swati Sharma (4):
drm/edid: Add additional HFVSDB fields for HDMI2.1
drm/edid: Parse MAX_FRL field from HFVSDB block
drm/dp_helper: Add support for link failure detection
drm/i915: Add support for enabling link status and recovery
drivers/gpu/drm/drm_dp_helper.c | 566 ++++++++++++++++++
drivers/gpu/drm/drm_edid.c | 103 ++++
drivers/gpu/drm/i915/display/intel_ddi.c | 6 +-
.../drm/i915/display/intel_display_types.h | 10 +
drivers/gpu/drm/i915/display/intel_dp.c | 442 +++++++++++++-
drivers/gpu/drm/i915/display/intel_dp.h | 7 +-
drivers/gpu/drm/i915/display/intel_hdmi.c | 233 +++++++
drivers/gpu/drm/i915/display/intel_hdmi.h | 7 +
include/drm/drm_connector.h | 49 ++
include/drm/drm_dp_helper.h | 218 +++++++
include/drm/drm_edid.h | 30 +
11 files changed, 1652 insertions(+), 19 deletions(-)
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* [PATCH v7 01/15] drm/edid: Add additional HFVSDB fields for HDMI2.1
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
From: Swati Sharma <swati2.sharma@intel.com>
The HDMI2.1 extends HFVSDB (HDMI Forum Vendor Specific
Data block) to have fields related to newly defined methods of FRL
(Fixed Rate Link) levels, number of lanes supported, DSC Color bit
depth, VRR min/max, FVA (Fast Vactive), ALLM etc.
This patch adds the new HFVSDB fields that are required for
HDMI2.1.
v2: Minor fixes + consistent naming for DPCD register masks
(Uma Shankar)
Signed-off-by: Sharma, Swati2 <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
include/drm/drm_edid.h | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/include/drm/drm_edid.h b/include/drm/drm_edid.h
index e97daf6ffbb1..a158f585f658 100644
--- a/include/drm/drm_edid.h
+++ b/include/drm/drm_edid.h
@@ -229,6 +229,36 @@ struct detailed_timing {
DRM_EDID_YCBCR420_DC_36 | \
DRM_EDID_YCBCR420_DC_30)
+/* HDMI 2.1 additional fields */
+#define DRM_EDID_MAX_FRL_RATE_MASK 0xf0
+#define DRM_EDID_FAPA_START_LOCATION (1 << 0)
+#define DRM_EDID_ALLM (1 << 1)
+#define DRM_EDID_FVA (1 << 2)
+
+/* Deep Color specific */
+#define DRM_EDID_DC_30BIT_420 (1 << 0)
+#define DRM_EDID_DC_36BIT_420 (1 << 1)
+#define DRM_EDID_DC_48BIT_420 (1 << 2)
+
+/* VRR specific */
+#define DRM_EDID_CNMVRR (1 << 3)
+#define DRM_EDID_CINEMA_VRR (1 << 4)
+#define DRM_EDID_MDELTA (1 << 5)
+#define DRM_EDID_VRR_MAX_UPPER_MASK 0xc0
+#define DRM_EDID_VRR_MAX_LOWER_MASK 0xff
+#define DRM_EDID_VRR_MIN_MASK 0x3f
+
+/* DSC specific */
+#define DRM_EDID_DSC_10BPC (1 << 0)
+#define DRM_EDID_DSC_12BPC (1 << 1)
+#define DRM_EDID_DSC_16BPC (1 << 2)
+#define DRM_EDID_DSC_ALL_BPP (1 << 3)
+#define DRM_EDID_DSC_NATIVE_420 (1 << 6)
+#define DRM_EDID_DSC_1P2 (1 << 7)
+#define DRM_EDID_DSC_MAX_FRL_RATE_MASK 0xf0
+#define DRM_EDID_DSC_MAX_SLICES 0xf
+#define DRM_EDID_DSC_TOTAL_CHUNK_KBYTES 0x3f
+
/* ELD Header Block */
#define DRM_ELD_HEADER_BLOCK_SIZE 4
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 01/15] drm/edid: Add additional HFVSDB fields for HDMI2.1
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
From: Swati Sharma <swati2.sharma@intel.com>
The HDMI2.1 extends HFVSDB (HDMI Forum Vendor Specific
Data block) to have fields related to newly defined methods of FRL
(Fixed Rate Link) levels, number of lanes supported, DSC Color bit
depth, VRR min/max, FVA (Fast Vactive), ALLM etc.
This patch adds the new HFVSDB fields that are required for
HDMI2.1.
v2: Minor fixes + consistent naming for DPCD register masks
(Uma Shankar)
Signed-off-by: Sharma, Swati2 <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
include/drm/drm_edid.h | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/include/drm/drm_edid.h b/include/drm/drm_edid.h
index e97daf6ffbb1..a158f585f658 100644
--- a/include/drm/drm_edid.h
+++ b/include/drm/drm_edid.h
@@ -229,6 +229,36 @@ struct detailed_timing {
DRM_EDID_YCBCR420_DC_36 | \
DRM_EDID_YCBCR420_DC_30)
+/* HDMI 2.1 additional fields */
+#define DRM_EDID_MAX_FRL_RATE_MASK 0xf0
+#define DRM_EDID_FAPA_START_LOCATION (1 << 0)
+#define DRM_EDID_ALLM (1 << 1)
+#define DRM_EDID_FVA (1 << 2)
+
+/* Deep Color specific */
+#define DRM_EDID_DC_30BIT_420 (1 << 0)
+#define DRM_EDID_DC_36BIT_420 (1 << 1)
+#define DRM_EDID_DC_48BIT_420 (1 << 2)
+
+/* VRR specific */
+#define DRM_EDID_CNMVRR (1 << 3)
+#define DRM_EDID_CINEMA_VRR (1 << 4)
+#define DRM_EDID_MDELTA (1 << 5)
+#define DRM_EDID_VRR_MAX_UPPER_MASK 0xc0
+#define DRM_EDID_VRR_MAX_LOWER_MASK 0xff
+#define DRM_EDID_VRR_MIN_MASK 0x3f
+
+/* DSC specific */
+#define DRM_EDID_DSC_10BPC (1 << 0)
+#define DRM_EDID_DSC_12BPC (1 << 1)
+#define DRM_EDID_DSC_16BPC (1 << 2)
+#define DRM_EDID_DSC_ALL_BPP (1 << 3)
+#define DRM_EDID_DSC_NATIVE_420 (1 << 6)
+#define DRM_EDID_DSC_1P2 (1 << 7)
+#define DRM_EDID_DSC_MAX_FRL_RATE_MASK 0xf0
+#define DRM_EDID_DSC_MAX_SLICES 0xf
+#define DRM_EDID_DSC_TOTAL_CHUNK_KBYTES 0x3f
+
/* ELD Header Block */
#define DRM_ELD_HEADER_BLOCK_SIZE 4
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 02/15] drm/edid: Parse MAX_FRL field from HFVSDB block
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
From: Swati Sharma <swati2.sharma@intel.com>
This patch parses MAX_FRL field to get the MAX rate in Gbps that
the HDMI 2.1 panel can support in FRL mode. Source need this
field to determine the optimal rate between the source and sink
during FRL training.
v2: Fixed minor bugs, and removed extra wrapper function (Uma Shankar)
Signed-off-by: Sharma, Swati2 <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/drm_edid.c | 44 +++++++++++++++++++++++++++++++++++++
include/drm/drm_connector.h | 6 +++++
2 files changed, 50 insertions(+)
diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c
index 74f5a3197214..e657c321d9e4 100644
--- a/drivers/gpu/drm/drm_edid.c
+++ b/drivers/gpu/drm/drm_edid.c
@@ -4851,6 +4851,41 @@ static void drm_parse_vcdb(struct drm_connector *connector, const u8 *db)
info->rgb_quant_range_selectable = true;
}
+static
+void drm_get_max_frl_rate(int max_frl_rate, u8 *max_lanes, u8 *max_rate_per_lane)
+{
+ switch (max_frl_rate) {
+ case 1:
+ *max_lanes = 3;
+ *max_rate_per_lane = 3;
+ break;
+ case 2:
+ *max_lanes = 3;
+ *max_rate_per_lane = 6;
+ break;
+ case 3:
+ *max_lanes = 4;
+ *max_rate_per_lane = 6;
+ break;
+ case 4:
+ *max_lanes = 4;
+ *max_rate_per_lane = 8;
+ break;
+ case 5:
+ *max_lanes = 4;
+ *max_rate_per_lane = 10;
+ break;
+ case 6:
+ *max_lanes = 4;
+ *max_rate_per_lane = 12;
+ break;
+ case 0:
+ default:
+ *max_lanes = 0;
+ *max_rate_per_lane = 0;
+ }
+}
+
static void drm_parse_ycbcr420_deep_color_info(struct drm_connector *connector,
const u8 *db)
{
@@ -4904,6 +4939,15 @@ static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
}
}
+ if (hf_vsdb[7]) {
+ u8 max_frl_rate;
+
+ DRM_DEBUG_KMS("hdmi_21 sink detected. parsing edid\n");
+ max_frl_rate = (hf_vsdb[7] & DRM_EDID_MAX_FRL_RATE_MASK) >> 4;
+ drm_get_max_frl_rate(max_frl_rate, &hdmi->max_lanes,
+ &hdmi->max_frl_rate_per_lane);
+ }
+
drm_parse_ycbcr420_deep_color_info(connector, hf_vsdb);
}
diff --git a/include/drm/drm_connector.h b/include/drm/drm_connector.h
index fcdc58d8b88b..1a3b4776b458 100644
--- a/include/drm/drm_connector.h
+++ b/include/drm/drm_connector.h
@@ -207,6 +207,12 @@ struct drm_hdmi_info {
/** @y420_dc_modes: bitmap of deep color support index */
u8 y420_dc_modes;
+
+ /** @max_frl_rate_per_lane: support fixed rate link */
+ u8 max_frl_rate_per_lane;
+
+ /** @max_lanes: supported by sink */
+ u8 max_lanes;
};
/**
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 02/15] drm/edid: Parse MAX_FRL field from HFVSDB block
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
From: Swati Sharma <swati2.sharma@intel.com>
This patch parses MAX_FRL field to get the MAX rate in Gbps that
the HDMI 2.1 panel can support in FRL mode. Source need this
field to determine the optimal rate between the source and sink
during FRL training.
v2: Fixed minor bugs, and removed extra wrapper function (Uma Shankar)
Signed-off-by: Sharma, Swati2 <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/drm_edid.c | 44 +++++++++++++++++++++++++++++++++++++
include/drm/drm_connector.h | 6 +++++
2 files changed, 50 insertions(+)
diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c
index 74f5a3197214..e657c321d9e4 100644
--- a/drivers/gpu/drm/drm_edid.c
+++ b/drivers/gpu/drm/drm_edid.c
@@ -4851,6 +4851,41 @@ static void drm_parse_vcdb(struct drm_connector *connector, const u8 *db)
info->rgb_quant_range_selectable = true;
}
+static
+void drm_get_max_frl_rate(int max_frl_rate, u8 *max_lanes, u8 *max_rate_per_lane)
+{
+ switch (max_frl_rate) {
+ case 1:
+ *max_lanes = 3;
+ *max_rate_per_lane = 3;
+ break;
+ case 2:
+ *max_lanes = 3;
+ *max_rate_per_lane = 6;
+ break;
+ case 3:
+ *max_lanes = 4;
+ *max_rate_per_lane = 6;
+ break;
+ case 4:
+ *max_lanes = 4;
+ *max_rate_per_lane = 8;
+ break;
+ case 5:
+ *max_lanes = 4;
+ *max_rate_per_lane = 10;
+ break;
+ case 6:
+ *max_lanes = 4;
+ *max_rate_per_lane = 12;
+ break;
+ case 0:
+ default:
+ *max_lanes = 0;
+ *max_rate_per_lane = 0;
+ }
+}
+
static void drm_parse_ycbcr420_deep_color_info(struct drm_connector *connector,
const u8 *db)
{
@@ -4904,6 +4939,15 @@ static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
}
}
+ if (hf_vsdb[7]) {
+ u8 max_frl_rate;
+
+ DRM_DEBUG_KMS("hdmi_21 sink detected. parsing edid\n");
+ max_frl_rate = (hf_vsdb[7] & DRM_EDID_MAX_FRL_RATE_MASK) >> 4;
+ drm_get_max_frl_rate(max_frl_rate, &hdmi->max_lanes,
+ &hdmi->max_frl_rate_per_lane);
+ }
+
drm_parse_ycbcr420_deep_color_info(connector, hf_vsdb);
}
diff --git a/include/drm/drm_connector.h b/include/drm/drm_connector.h
index fcdc58d8b88b..1a3b4776b458 100644
--- a/include/drm/drm_connector.h
+++ b/include/drm/drm_connector.h
@@ -207,6 +207,12 @@ struct drm_hdmi_info {
/** @y420_dc_modes: bitmap of deep color support index */
u8 y420_dc_modes;
+
+ /** @max_frl_rate_per_lane: support fixed rate link */
+ u8 max_frl_rate_per_lane;
+
+ /** @max_lanes: supported by sink */
+ u8 max_lanes;
};
/**
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 03/15] drm/edid: Parse DSC1.2 cap fields from HFVSDB block
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
This patch parses HFVSDB fields for DSC1.2 capabilities of an
HDMI2.1 sink. These fields are required by a source to understand the
DSC capability of the sink, to set appropriate PPS parameters,
before transmitting compressed data stream.
v2: Addressed following issues as suggested by Uma Shankar:
-Added a new struct for hdmi dsc cap
-Fixed bugs in macros usage.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/drm_edid.c | 59 +++++++++++++++++++++++++++++++++++++
include/drm/drm_connector.h | 43 +++++++++++++++++++++++++++
2 files changed, 102 insertions(+)
diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c
index e657c321d9e4..ca368df2e5ac 100644
--- a/drivers/gpu/drm/drm_edid.c
+++ b/drivers/gpu/drm/drm_edid.c
@@ -4941,11 +4941,70 @@ static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
if (hf_vsdb[7]) {
u8 max_frl_rate;
+ u8 dsc_max_frl_rate;
+ u8 dsc_max_slices;
+ struct drm_hdmi_dsc_cap *hdmi_dsc = &hdmi->dsc_cap;
DRM_DEBUG_KMS("hdmi_21 sink detected. parsing edid\n");
max_frl_rate = (hf_vsdb[7] & DRM_EDID_MAX_FRL_RATE_MASK) >> 4;
drm_get_max_frl_rate(max_frl_rate, &hdmi->max_lanes,
&hdmi->max_frl_rate_per_lane);
+ hdmi_dsc->v_1p2 = hf_vsdb[11] & DRM_EDID_DSC_1P2;
+
+ if (hdmi_dsc->v_1p2) {
+ hdmi_dsc->native_420 = hf_vsdb[11] & DRM_EDID_DSC_NATIVE_420;
+ hdmi_dsc->all_bpp = hf_vsdb[11] & DRM_EDID_DSC_ALL_BPP;
+
+ if (hf_vsdb[11] & DRM_EDID_DSC_16BPC)
+ hdmi_dsc->bpc_supported = 16;
+ else if (hf_vsdb[11] & DRM_EDID_DSC_12BPC)
+ hdmi_dsc->bpc_supported = 12;
+ else if (hf_vsdb[11] & DRM_EDID_DSC_10BPC)
+ hdmi_dsc->bpc_supported = 10;
+ else
+ hdmi_dsc->bpc_supported = 0;
+
+ dsc_max_frl_rate = (hf_vsdb[12] & DRM_EDID_DSC_MAX_FRL_RATE_MASK) >> 4;
+ drm_get_max_frl_rate(dsc_max_frl_rate, &hdmi_dsc->max_lanes,
+ &hdmi_dsc->max_frl_rate_per_lane);
+ hdmi_dsc->total_chunk_kbytes = hf_vsdb[13] & DRM_EDID_DSC_TOTAL_CHUNK_KBYTES;
+
+ dsc_max_slices = hf_vsdb[12] & DRM_EDID_DSC_MAX_SLICES;
+ switch (dsc_max_slices) {
+ case 1:
+ hdmi_dsc->max_slices = 1;
+ hdmi_dsc->clk_per_slice = 340;
+ break;
+ case 2:
+ hdmi_dsc->max_slices = 2;
+ hdmi_dsc->clk_per_slice = 340;
+ break;
+ case 3:
+ hdmi_dsc->max_slices = 4;
+ hdmi_dsc->clk_per_slice = 340;
+ break;
+ case 4:
+ hdmi_dsc->max_slices = 8;
+ hdmi_dsc->clk_per_slice = 340;
+ break;
+ case 5:
+ hdmi_dsc->max_slices = 8;
+ hdmi_dsc->clk_per_slice = 400;
+ break;
+ case 6:
+ hdmi_dsc->max_slices = 12;
+ hdmi_dsc->clk_per_slice = 400;
+ break;
+ case 7:
+ hdmi_dsc->max_slices = 16;
+ hdmi_dsc->clk_per_slice = 400;
+ break;
+ case 0:
+ default:
+ hdmi_dsc->max_slices = 0;
+ hdmi_dsc->clk_per_slice = 0;
+ }
+ }
}
drm_parse_ycbcr420_deep_color_info(connector, hf_vsdb);
diff --git a/include/drm/drm_connector.h b/include/drm/drm_connector.h
index 1a3b4776b458..1922b278ffad 100644
--- a/include/drm/drm_connector.h
+++ b/include/drm/drm_connector.h
@@ -175,6 +175,46 @@ struct drm_scdc {
struct drm_scrambling scrambling;
};
+/**
+ * struct drm_hdmi_dsc_cap - DSC capabilities of HDMI sink
+ *
+ * Describes the DSC support provided by HDMI 2.1 sink.
+ * The information is fetched fom additional HFVSDB blocks defined
+ * for HDMI 2.1.
+ */
+struct drm_hdmi_dsc_cap {
+ /** @v_1p2: flag for dsc1.2 version support by sink */
+ bool v_1p2;
+
+ /** @native_420: Does sink support DSC with 4:2:0 compression */
+ bool native_420;
+
+ /**
+ * @all_bpp: Does sink support all bpp with 4:4:4: or 4:2:2
+ * compressed formats
+ */
+ bool all_bpp;
+
+ /**
+ * @bpc_supported: compressed bpc supported by sink : 10, 12 or 16 bpc
+ */
+ u8 bpc_supported;
+
+ /** @max_slices: maximum number of Horizontal slices supported by */
+ u8 max_slices;
+
+ /** @clk_per_slice : max pixel clock in MHz supported per slice */
+ int clk_per_slice;
+
+ /** @max_lanes : dsc max lanes supported for Fixed rate Link training */
+ u8 max_lanes;
+
+ /** @max_frl_rate_per_lane : maximum frl rate with DSC per lane */
+ u8 max_frl_rate_per_lane;
+
+ /** @total_chunk_kbytes: max size of chunks in KBs supported per line*/
+ u8 total_chunk_kbytes;
+};
/**
* struct drm_hdmi_info - runtime information about the connected HDMI sink
@@ -213,6 +253,9 @@ struct drm_hdmi_info {
/** @max_lanes: supported by sink */
u8 max_lanes;
+
+ /** @dsc_cap: DSC capabilities of the sink */
+ struct drm_hdmi_dsc_cap dsc_cap;
};
/**
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 03/15] drm/edid: Parse DSC1.2 cap fields from HFVSDB block
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
This patch parses HFVSDB fields for DSC1.2 capabilities of an
HDMI2.1 sink. These fields are required by a source to understand the
DSC capability of the sink, to set appropriate PPS parameters,
before transmitting compressed data stream.
v2: Addressed following issues as suggested by Uma Shankar:
-Added a new struct for hdmi dsc cap
-Fixed bugs in macros usage.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/drm_edid.c | 59 +++++++++++++++++++++++++++++++++++++
include/drm/drm_connector.h | 43 +++++++++++++++++++++++++++
2 files changed, 102 insertions(+)
diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c
index e657c321d9e4..ca368df2e5ac 100644
--- a/drivers/gpu/drm/drm_edid.c
+++ b/drivers/gpu/drm/drm_edid.c
@@ -4941,11 +4941,70 @@ static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
if (hf_vsdb[7]) {
u8 max_frl_rate;
+ u8 dsc_max_frl_rate;
+ u8 dsc_max_slices;
+ struct drm_hdmi_dsc_cap *hdmi_dsc = &hdmi->dsc_cap;
DRM_DEBUG_KMS("hdmi_21 sink detected. parsing edid\n");
max_frl_rate = (hf_vsdb[7] & DRM_EDID_MAX_FRL_RATE_MASK) >> 4;
drm_get_max_frl_rate(max_frl_rate, &hdmi->max_lanes,
&hdmi->max_frl_rate_per_lane);
+ hdmi_dsc->v_1p2 = hf_vsdb[11] & DRM_EDID_DSC_1P2;
+
+ if (hdmi_dsc->v_1p2) {
+ hdmi_dsc->native_420 = hf_vsdb[11] & DRM_EDID_DSC_NATIVE_420;
+ hdmi_dsc->all_bpp = hf_vsdb[11] & DRM_EDID_DSC_ALL_BPP;
+
+ if (hf_vsdb[11] & DRM_EDID_DSC_16BPC)
+ hdmi_dsc->bpc_supported = 16;
+ else if (hf_vsdb[11] & DRM_EDID_DSC_12BPC)
+ hdmi_dsc->bpc_supported = 12;
+ else if (hf_vsdb[11] & DRM_EDID_DSC_10BPC)
+ hdmi_dsc->bpc_supported = 10;
+ else
+ hdmi_dsc->bpc_supported = 0;
+
+ dsc_max_frl_rate = (hf_vsdb[12] & DRM_EDID_DSC_MAX_FRL_RATE_MASK) >> 4;
+ drm_get_max_frl_rate(dsc_max_frl_rate, &hdmi_dsc->max_lanes,
+ &hdmi_dsc->max_frl_rate_per_lane);
+ hdmi_dsc->total_chunk_kbytes = hf_vsdb[13] & DRM_EDID_DSC_TOTAL_CHUNK_KBYTES;
+
+ dsc_max_slices = hf_vsdb[12] & DRM_EDID_DSC_MAX_SLICES;
+ switch (dsc_max_slices) {
+ case 1:
+ hdmi_dsc->max_slices = 1;
+ hdmi_dsc->clk_per_slice = 340;
+ break;
+ case 2:
+ hdmi_dsc->max_slices = 2;
+ hdmi_dsc->clk_per_slice = 340;
+ break;
+ case 3:
+ hdmi_dsc->max_slices = 4;
+ hdmi_dsc->clk_per_slice = 340;
+ break;
+ case 4:
+ hdmi_dsc->max_slices = 8;
+ hdmi_dsc->clk_per_slice = 340;
+ break;
+ case 5:
+ hdmi_dsc->max_slices = 8;
+ hdmi_dsc->clk_per_slice = 400;
+ break;
+ case 6:
+ hdmi_dsc->max_slices = 12;
+ hdmi_dsc->clk_per_slice = 400;
+ break;
+ case 7:
+ hdmi_dsc->max_slices = 16;
+ hdmi_dsc->clk_per_slice = 400;
+ break;
+ case 0:
+ default:
+ hdmi_dsc->max_slices = 0;
+ hdmi_dsc->clk_per_slice = 0;
+ }
+ }
}
drm_parse_ycbcr420_deep_color_info(connector, hf_vsdb);
diff --git a/include/drm/drm_connector.h b/include/drm/drm_connector.h
index 1a3b4776b458..1922b278ffad 100644
--- a/include/drm/drm_connector.h
+++ b/include/drm/drm_connector.h
@@ -175,6 +175,46 @@ struct drm_scdc {
struct drm_scrambling scrambling;
};
+/**
+ * struct drm_hdmi_dsc_cap - DSC capabilities of HDMI sink
+ *
+ * Describes the DSC support provided by HDMI 2.1 sink.
+ * The information is fetched fom additional HFVSDB blocks defined
+ * for HDMI 2.1.
+ */
+struct drm_hdmi_dsc_cap {
+ /** @v_1p2: flag for dsc1.2 version support by sink */
+ bool v_1p2;
+
+ /** @native_420: Does sink support DSC with 4:2:0 compression */
+ bool native_420;
+
+ /**
+ * @all_bpp: Does sink support all bpp with 4:4:4: or 4:2:2
+ * compressed formats
+ */
+ bool all_bpp;
+
+ /**
+ * @bpc_supported: compressed bpc supported by sink : 10, 12 or 16 bpc
+ */
+ u8 bpc_supported;
+
+ /** @max_slices: maximum number of Horizontal slices supported by */
+ u8 max_slices;
+
+ /** @clk_per_slice : max pixel clock in MHz supported per slice */
+ int clk_per_slice;
+
+ /** @max_lanes : dsc max lanes supported for Fixed rate Link training */
+ u8 max_lanes;
+
+ /** @max_frl_rate_per_lane : maximum frl rate with DSC per lane */
+ u8 max_frl_rate_per_lane;
+
+ /** @total_chunk_kbytes: max size of chunks in KBs supported per line*/
+ u8 total_chunk_kbytes;
+};
/**
* struct drm_hdmi_info - runtime information about the connected HDMI sink
@@ -213,6 +253,9 @@ struct drm_hdmi_info {
/** @max_lanes: supported by sink */
u8 max_lanes;
+
+ /** @dsc_cap: DSC capabilities of the sink */
+ struct drm_hdmi_dsc_cap dsc_cap;
};
/**
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 04/15] drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
This patch adds support for configuring a PCON device,
connected as a DP branched device to enable FRL Link training
with a HDMI2.1 + sink.
v2: Fixed typos and addressed other review comments from Uma Shankar.
-changed the commit message for better clarity (Uma Shankar)
-removed unnecessary argument supplied to a drm helper function.
-fixed return value for max frl read from pcon.
v3: Removed DPCD 0x3035 for MAX Sink FRL b/w as per new version of spec.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
---
drivers/gpu/drm/drm_dp_helper.c | 263 ++++++++++++++++++++++++++++++++
include/drm/drm_dp_helper.h | 70 +++++++++
2 files changed, 333 insertions(+)
diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c
index 5bd0934004e3..f501e3890921 100644
--- a/drivers/gpu/drm/drm_dp_helper.c
+++ b/drivers/gpu/drm/drm_dp_helper.c
@@ -2596,3 +2596,266 @@ void drm_dp_vsc_sdp_log(const char *level, struct device *dev,
#undef DP_SDP_LOG
}
EXPORT_SYMBOL(drm_dp_vsc_sdp_log);
+
+/**
+ * drm_dp_get_pcon_max_frl_bw() - maximum frl supported by PCON
+ * @dpcd: DisplayPort configuration data
+ * @port_cap: port capabilities
+ *
+ * Returns maximum frl bandwidth supported by PCON in GBPS,
+ * returns 0 if not supported.
+ */
+int drm_dp_get_pcon_max_frl_bw(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
+ const u8 port_cap[4])
+{
+ int bw;
+ u8 buf;
+
+ buf = port_cap[2];
+ bw = buf & DP_PCON_MAX_FRL_BW;
+
+ switch (bw) {
+ case DP_PCON_MAX_9GBPS:
+ return 9;
+ case DP_PCON_MAX_18GBPS:
+ return 18;
+ case DP_PCON_MAX_24GBPS:
+ return 24;
+ case DP_PCON_MAX_32GBPS:
+ return 32;
+ case DP_PCON_MAX_40GBPS:
+ return 40;
+ case DP_PCON_MAX_48GBPS:
+ return 48;
+ case DP_PCON_MAX_0GBPS:
+ default:
+ return 0;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_get_pcon_max_frl_bw);
+
+/**
+ * drm_dp_pcon_frl_prepare() - Prepare PCON for FRL.
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns 0 if success, else returns negative error code.
+ */
+int drm_dp_pcon_frl_prepare(struct drm_dp_aux *aux, bool enable_frl_ready_hpd)
+{
+ int ret;
+ u8 buf = DP_PCON_ENABLE_SOURCE_CTL_MODE |
+ DP_PCON_ENABLE_LINK_FRL_MODE;
+
+ if (enable_frl_ready_hpd)
+ buf |= DP_PCON_ENABLE_HPD_READY;
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
+
+ return ret;
+}
+EXPORT_SYMBOL(drm_dp_pcon_frl_prepare);
+
+/**
+ * drm_dp_pcon_is_frl_ready() - Is PCON ready for FRL
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns true if success, else returns false.
+ */
+bool drm_dp_pcon_is_frl_ready(struct drm_dp_aux *aux)
+{
+ int ret;
+ u8 buf;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_TX_LINK_STATUS, &buf);
+ if (ret < 0)
+ return false;
+
+ if (buf & DP_PCON_FRL_READY)
+ return true;
+
+ return false;
+}
+EXPORT_SYMBOL(drm_dp_pcon_is_frl_ready);
+
+/**
+ * drm_dp_pcon_frl_configure_1() - Set HDMI LINK Configuration-Step1
+ * @aux: DisplayPort AUX channel
+ * @max_frl_gbps: maximum frl bw to be configured between PCON and HDMI sink
+ * @concurrent_mode: true if concurrent mode or operation is required,
+ * false otherwise.
+ *
+ * Returns 0 if success, else returns negative error code.
+ */
+
+int drm_dp_pcon_frl_configure_1(struct drm_dp_aux *aux, int max_frl_gbps,
+ bool concurrent_mode)
+{
+ int ret;
+ u8 buf;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf);
+ if (ret < 0)
+ return ret;
+
+ if (concurrent_mode)
+ buf |= DP_PCON_ENABLE_CONCURRENT_LINK;
+ else
+ buf &= ~DP_PCON_ENABLE_CONCURRENT_LINK;
+
+ switch (max_frl_gbps) {
+ case 9:
+ buf |= DP_PCON_ENABLE_MAX_BW_9GBPS;
+ break;
+ case 18:
+ buf |= DP_PCON_ENABLE_MAX_BW_18GBPS;
+ break;
+ case 24:
+ buf |= DP_PCON_ENABLE_MAX_BW_24GBPS;
+ break;
+ case 32:
+ buf |= DP_PCON_ENABLE_MAX_BW_32GBPS;
+ break;
+ case 40:
+ buf |= DP_PCON_ENABLE_MAX_BW_40GBPS;
+ break;
+ case 48:
+ buf |= DP_PCON_ENABLE_MAX_BW_48GBPS;
+ break;
+ case 0:
+ buf |= DP_PCON_ENABLE_MAX_BW_0GBPS;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_frl_configure_1);
+
+/**
+ * drm_dp_pcon_frl_configure_2() - Set HDMI Link configuration Step-2
+ * @aux: DisplayPort AUX channel
+ * @max_frl_mask : Max FRL BW to be tried by the PCON with HDMI Sink
+ * @extended_train_mode : true for Extended Mode, false for Normal Mode.
+ * In Normal mode, the PCON tries each frl bw from the max_frl_mask starting
+ * from min, and stops when link training is successful. In Extended mode, all
+ * frl bw selected in the mask are trained by the PCON.
+ *
+ * Returns 0 if success, else returns negative error code.
+ */
+int drm_dp_pcon_frl_configure_2(struct drm_dp_aux *aux, int max_frl_mask,
+ bool extended_train_mode)
+{
+ int ret;
+ u8 buf = max_frl_mask;
+
+ if (extended_train_mode)
+ buf |= DP_PCON_FRL_LINK_TRAIN_EXTENDED;
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_2, buf);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_frl_configure_2);
+
+/**
+ * drm_dp_pcon_reset_frl_config() - Re-Set HDMI Link configuration.
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns 0 if success, else returns negative error code.
+ */
+int drm_dp_pcon_reset_frl_config(struct drm_dp_aux *aux)
+{
+ int ret;
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, 0x0);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_reset_frl_config);
+
+/**
+ * drm_dp_pcon_frl_enable() - Enable HDMI link through FRL
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns 0 if success, else returns negative error code.
+ */
+int drm_dp_pcon_frl_enable(struct drm_dp_aux *aux)
+{
+ int ret;
+ u8 buf = 0;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf);
+ if (ret < 0)
+ return ret;
+ if (!(buf & DP_PCON_ENABLE_SOURCE_CTL_MODE)) {
+ DRM_DEBUG_KMS("PCON in Autonomous mode, can't enable FRL\n");
+ return -EINVAL;
+ }
+ buf |= DP_PCON_ENABLE_HDMI_LINK;
+ ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_frl_enable);
+
+/**
+ * drm_dp_pcon_hdmi_link_active() - check if the PCON HDMI LINK status is active.
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns true if link is active else returns false.
+ */
+bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux)
+{
+ u8 buf;
+ int ret;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_TX_LINK_STATUS, &buf);
+ if (ret < 0)
+ return false;
+
+ return buf & DP_PCON_HDMI_TX_LINK_ACTIVE;
+}
+EXPORT_SYMBOL(drm_dp_pcon_hdmi_link_active);
+
+/**
+ * drm_dp_pcon_hdmi_link_mode() - get the PCON HDMI LINK MODE
+ * @aux: DisplayPort AUX channel
+ * @frl_trained_mask: pointer to store bitmask of the trained bw configuration.
+ * Valid only if the MODE returned is FRL. For Normal Link training mode
+ * only 1 of the bits will be set, but in case of Extended mode, more than
+ * one bits can be set.
+ *
+ * Returns the link mode : TMDS or FRL on success, else returns negative error
+ * code.
+ */
+int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask)
+{
+ u8 buf;
+ int mode;
+ int ret;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_POST_FRL_STATUS, &buf);
+ if (ret < 0)
+ return ret;
+
+ mode = buf & DP_PCON_HDMI_LINK_MODE;
+
+ if (frl_trained_mask && DP_PCON_HDMI_MODE_FRL == mode)
+ *frl_trained_mask = (buf & DP_PCON_HDMI_FRL_TRAINED_BW) >> 1;
+
+ return mode;
+}
+EXPORT_SYMBOL(drm_dp_pcon_hdmi_link_mode);
diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
index 6b40258927bf..c66f570eadc2 100644
--- a/include/drm/drm_dp_helper.h
+++ b/include/drm/drm_dp_helper.h
@@ -411,6 +411,17 @@ struct drm_device;
# define DP_DS_10BPC 1
# define DP_DS_12BPC 2
# define DP_DS_16BPC 3
+/* HDMI2.1 PCON FRL CONFIGURATION */
+# define DP_PCON_MAX_FRL_BW (7 << 2)
+# define DP_PCON_MAX_0GBPS (0 << 2)
+# define DP_PCON_MAX_9GBPS (1 << 2)
+# define DP_PCON_MAX_18GBPS (2 << 2)
+# define DP_PCON_MAX_24GBPS (3 << 2)
+# define DP_PCON_MAX_32GBPS (4 << 2)
+# define DP_PCON_MAX_40GBPS (5 << 2)
+# define DP_PCON_MAX_48GBPS (6 << 2)
+# define DP_PCON_SOURCE_CTL_MODE (1 << 5)
+
/* offset 3 for DVI */
# define DP_DS_DVI_DUAL_LINK (1 << 1)
# define DP_DS_DVI_HIGH_COLOR_DEPTH (1 << 2)
@@ -1054,6 +1065,51 @@ struct drm_device;
#define DP_CEC_TX_MESSAGE_BUFFER 0x3020
#define DP_CEC_MESSAGE_BUFFER_LENGTH 0x10
+/* PCON CONFIGURE-1 FRL FOR HDMI SINK */
+#define DP_PCON_HDMI_LINK_CONFIG_1 0x305A
+# define DP_PCON_ENABLE_MAX_FRL_BW (7 << 0)
+# define DP_PCON_ENABLE_MAX_BW_0GBPS 0
+# define DP_PCON_ENABLE_MAX_BW_9GBPS 1
+# define DP_PCON_ENABLE_MAX_BW_18GBPS 2
+# define DP_PCON_ENABLE_MAX_BW_24GBPS 3
+# define DP_PCON_ENABLE_MAX_BW_32GBPS 4
+# define DP_PCON_ENABLE_MAX_BW_40GBPS 5
+# define DP_PCON_ENABLE_MAX_BW_48GBPS 6
+# define DP_PCON_ENABLE_SOURCE_CTL_MODE (1 << 3)
+# define DP_PCON_ENABLE_CONCURRENT_LINK (1 << 4)
+# define DP_PCON_ENABLE_LINK_FRL_MODE (1 << 5)
+# define DP_PCON_ENABLE_HPD_READY (1 << 6)
+# define DP_PCON_ENABLE_HDMI_LINK (1 << 7)
+
+/* PCON CONFIGURE-2 FRL FOR HDMI SINK */
+#define DP_PCON_HDMI_LINK_CONFIG_2 0x305B
+# define DP_PCON_MAX_LINK_BW_MASK (0x3F << 0)
+# define DP_PCON_FRL_BW_MASK_9GBPS (1 << 0)
+# define DP_PCON_FRL_BW_MASK_18GBPS (1 << 1)
+# define DP_PCON_FRL_BW_MASK_24GBPS (1 << 2)
+# define DP_PCON_FRL_BW_MASK_32GBPS (1 << 3)
+# define DP_PCON_FRL_BW_MASK_40GBPS (1 << 4)
+# define DP_PCON_FRL_BW_MASK_48GBPS (1 << 5)
+# define DP_PCON_FRL_LINK_TRAIN_EXTENDED (1 << 6)
+
+/* PCON HDMI LINK STATUS */
+#define DP_PCON_HDMI_TX_LINK_STATUS 0x303B
+# define DP_PCON_HDMI_TX_LINK_ACTIVE (1 << 0)
+# define DP_PCON_FRL_READY (1 << 1)
+
+/* PCON HDMI POST FRL STATUS */
+#define DP_PCON_HDMI_POST_FRL_STATUS 0x3036
+# define DP_PCON_HDMI_LINK_MODE (1 << 0)
+# define DP_PCON_HDMI_MODE_TMDS 0
+# define DP_PCON_HDMI_MODE_FRL 1
+# define DP_PCON_HDMI_FRL_TRAINED_BW (0x3F << 1)
+# define DP_PCON_FRL_TRAINED_BW_9GBPS (1 << 1)
+# define DP_PCON_FRL_TRAINED_BW_18GBPS (1 << 2)
+# define DP_PCON_FRL_TRAINED_BW_24GBPS (1 << 3)
+# define DP_PCON_FRL_TRAINED_BW_32GBPS (1 << 4)
+# define DP_PCON_FRL_TRAINED_BW_40GBPS (1 << 5)
+# define DP_PCON_FRL_TRAINED_BW_48GBPS (1 << 6)
+
#define DP_PROTOCOL_CONVERTER_CONTROL_0 0x3050 /* DP 1.3 */
# define DP_HDMI_DVI_OUTPUT_CONFIG (1 << 0) /* DP 1.3 */
#define DP_PROTOCOL_CONVERTER_CONTROL_1 0x3051 /* DP 1.3 */
@@ -1967,4 +2023,18 @@ int drm_dp_get_phy_test_pattern(struct drm_dp_aux *aux,
struct drm_dp_phy_test_params *data);
int drm_dp_set_phy_test_pattern(struct drm_dp_aux *aux,
struct drm_dp_phy_test_params *data, u8 dp_rev);
+int drm_dp_get_pcon_max_frl_bw(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
+ const u8 port_cap[4]);
+int drm_dp_pcon_frl_prepare(struct drm_dp_aux *aux, bool enable_frl_ready_hpd);
+bool drm_dp_pcon_is_frl_ready(struct drm_dp_aux *aux);
+int drm_dp_pcon_frl_configure_1(struct drm_dp_aux *aux, int max_frl_gbps,
+ bool concurrent_mode);
+int drm_dp_pcon_frl_configure_2(struct drm_dp_aux *aux, int max_frl_mask,
+ bool extended_train_mode);
+int drm_dp_pcon_reset_frl_config(struct drm_dp_aux *aux);
+int drm_dp_pcon_frl_enable(struct drm_dp_aux *aux);
+
+bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux);
+int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask);
+
#endif /* _DRM_DP_HELPER_H_ */
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 04/15] drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
This patch adds support for configuring a PCON device,
connected as a DP branched device to enable FRL Link training
with a HDMI2.1 + sink.
v2: Fixed typos and addressed other review comments from Uma Shankar.
-changed the commit message for better clarity (Uma Shankar)
-removed unnecessary argument supplied to a drm helper function.
-fixed return value for max frl read from pcon.
v3: Removed DPCD 0x3035 for MAX Sink FRL b/w as per new version of spec.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
---
drivers/gpu/drm/drm_dp_helper.c | 263 ++++++++++++++++++++++++++++++++
include/drm/drm_dp_helper.h | 70 +++++++++
2 files changed, 333 insertions(+)
diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c
index 5bd0934004e3..f501e3890921 100644
--- a/drivers/gpu/drm/drm_dp_helper.c
+++ b/drivers/gpu/drm/drm_dp_helper.c
@@ -2596,3 +2596,266 @@ void drm_dp_vsc_sdp_log(const char *level, struct device *dev,
#undef DP_SDP_LOG
}
EXPORT_SYMBOL(drm_dp_vsc_sdp_log);
+
+/**
+ * drm_dp_get_pcon_max_frl_bw() - maximum frl supported by PCON
+ * @dpcd: DisplayPort configuration data
+ * @port_cap: port capabilities
+ *
+ * Returns maximum frl bandwidth supported by PCON in GBPS,
+ * returns 0 if not supported.
+ */
+int drm_dp_get_pcon_max_frl_bw(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
+ const u8 port_cap[4])
+{
+ int bw;
+ u8 buf;
+
+ buf = port_cap[2];
+ bw = buf & DP_PCON_MAX_FRL_BW;
+
+ switch (bw) {
+ case DP_PCON_MAX_9GBPS:
+ return 9;
+ case DP_PCON_MAX_18GBPS:
+ return 18;
+ case DP_PCON_MAX_24GBPS:
+ return 24;
+ case DP_PCON_MAX_32GBPS:
+ return 32;
+ case DP_PCON_MAX_40GBPS:
+ return 40;
+ case DP_PCON_MAX_48GBPS:
+ return 48;
+ case DP_PCON_MAX_0GBPS:
+ default:
+ return 0;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_get_pcon_max_frl_bw);
+
+/**
+ * drm_dp_pcon_frl_prepare() - Prepare PCON for FRL.
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns 0 if success, else returns negative error code.
+ */
+int drm_dp_pcon_frl_prepare(struct drm_dp_aux *aux, bool enable_frl_ready_hpd)
+{
+ int ret;
+ u8 buf = DP_PCON_ENABLE_SOURCE_CTL_MODE |
+ DP_PCON_ENABLE_LINK_FRL_MODE;
+
+ if (enable_frl_ready_hpd)
+ buf |= DP_PCON_ENABLE_HPD_READY;
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
+
+ return ret;
+}
+EXPORT_SYMBOL(drm_dp_pcon_frl_prepare);
+
+/**
+ * drm_dp_pcon_is_frl_ready() - Is PCON ready for FRL
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns true if success, else returns false.
+ */
+bool drm_dp_pcon_is_frl_ready(struct drm_dp_aux *aux)
+{
+ int ret;
+ u8 buf;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_TX_LINK_STATUS, &buf);
+ if (ret < 0)
+ return false;
+
+ if (buf & DP_PCON_FRL_READY)
+ return true;
+
+ return false;
+}
+EXPORT_SYMBOL(drm_dp_pcon_is_frl_ready);
+
+/**
+ * drm_dp_pcon_frl_configure_1() - Set HDMI LINK Configuration-Step1
+ * @aux: DisplayPort AUX channel
+ * @max_frl_gbps: maximum frl bw to be configured between PCON and HDMI sink
+ * @concurrent_mode: true if concurrent mode or operation is required,
+ * false otherwise.
+ *
+ * Returns 0 if success, else returns negative error code.
+ */
+
+int drm_dp_pcon_frl_configure_1(struct drm_dp_aux *aux, int max_frl_gbps,
+ bool concurrent_mode)
+{
+ int ret;
+ u8 buf;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf);
+ if (ret < 0)
+ return ret;
+
+ if (concurrent_mode)
+ buf |= DP_PCON_ENABLE_CONCURRENT_LINK;
+ else
+ buf &= ~DP_PCON_ENABLE_CONCURRENT_LINK;
+
+ switch (max_frl_gbps) {
+ case 9:
+ buf |= DP_PCON_ENABLE_MAX_BW_9GBPS;
+ break;
+ case 18:
+ buf |= DP_PCON_ENABLE_MAX_BW_18GBPS;
+ break;
+ case 24:
+ buf |= DP_PCON_ENABLE_MAX_BW_24GBPS;
+ break;
+ case 32:
+ buf |= DP_PCON_ENABLE_MAX_BW_32GBPS;
+ break;
+ case 40:
+ buf |= DP_PCON_ENABLE_MAX_BW_40GBPS;
+ break;
+ case 48:
+ buf |= DP_PCON_ENABLE_MAX_BW_48GBPS;
+ break;
+ case 0:
+ buf |= DP_PCON_ENABLE_MAX_BW_0GBPS;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_frl_configure_1);
+
+/**
+ * drm_dp_pcon_frl_configure_2() - Set HDMI Link configuration Step-2
+ * @aux: DisplayPort AUX channel
+ * @max_frl_mask : Max FRL BW to be tried by the PCON with HDMI Sink
+ * @extended_train_mode : true for Extended Mode, false for Normal Mode.
+ * In Normal mode, the PCON tries each frl bw from the max_frl_mask starting
+ * from min, and stops when link training is successful. In Extended mode, all
+ * frl bw selected in the mask are trained by the PCON.
+ *
+ * Returns 0 if success, else returns negative error code.
+ */
+int drm_dp_pcon_frl_configure_2(struct drm_dp_aux *aux, int max_frl_mask,
+ bool extended_train_mode)
+{
+ int ret;
+ u8 buf = max_frl_mask;
+
+ if (extended_train_mode)
+ buf |= DP_PCON_FRL_LINK_TRAIN_EXTENDED;
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_2, buf);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_frl_configure_2);
+
+/**
+ * drm_dp_pcon_reset_frl_config() - Re-Set HDMI Link configuration.
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns 0 if success, else returns negative error code.
+ */
+int drm_dp_pcon_reset_frl_config(struct drm_dp_aux *aux)
+{
+ int ret;
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, 0x0);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_reset_frl_config);
+
+/**
+ * drm_dp_pcon_frl_enable() - Enable HDMI link through FRL
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns 0 if success, else returns negative error code.
+ */
+int drm_dp_pcon_frl_enable(struct drm_dp_aux *aux)
+{
+ int ret;
+ u8 buf = 0;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf);
+ if (ret < 0)
+ return ret;
+ if (!(buf & DP_PCON_ENABLE_SOURCE_CTL_MODE)) {
+ DRM_DEBUG_KMS("PCON in Autonomous mode, can't enable FRL\n");
+ return -EINVAL;
+ }
+ buf |= DP_PCON_ENABLE_HDMI_LINK;
+ ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_frl_enable);
+
+/**
+ * drm_dp_pcon_hdmi_link_active() - check if the PCON HDMI LINK status is active.
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns true if link is active else returns false.
+ */
+bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux)
+{
+ u8 buf;
+ int ret;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_TX_LINK_STATUS, &buf);
+ if (ret < 0)
+ return false;
+
+ return buf & DP_PCON_HDMI_TX_LINK_ACTIVE;
+}
+EXPORT_SYMBOL(drm_dp_pcon_hdmi_link_active);
+
+/**
+ * drm_dp_pcon_hdmi_link_mode() - get the PCON HDMI LINK MODE
+ * @aux: DisplayPort AUX channel
+ * @frl_trained_mask: pointer to store bitmask of the trained bw configuration.
+ * Valid only if the MODE returned is FRL. For Normal Link training mode
+ * only 1 of the bits will be set, but in case of Extended mode, more than
+ * one bits can be set.
+ *
+ * Returns the link mode : TMDS or FRL on success, else returns negative error
+ * code.
+ */
+int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask)
+{
+ u8 buf;
+ int mode;
+ int ret;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_POST_FRL_STATUS, &buf);
+ if (ret < 0)
+ return ret;
+
+ mode = buf & DP_PCON_HDMI_LINK_MODE;
+
+ if (frl_trained_mask && DP_PCON_HDMI_MODE_FRL == mode)
+ *frl_trained_mask = (buf & DP_PCON_HDMI_FRL_TRAINED_BW) >> 1;
+
+ return mode;
+}
+EXPORT_SYMBOL(drm_dp_pcon_hdmi_link_mode);
diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
index 6b40258927bf..c66f570eadc2 100644
--- a/include/drm/drm_dp_helper.h
+++ b/include/drm/drm_dp_helper.h
@@ -411,6 +411,17 @@ struct drm_device;
# define DP_DS_10BPC 1
# define DP_DS_12BPC 2
# define DP_DS_16BPC 3
+/* HDMI2.1 PCON FRL CONFIGURATION */
+# define DP_PCON_MAX_FRL_BW (7 << 2)
+# define DP_PCON_MAX_0GBPS (0 << 2)
+# define DP_PCON_MAX_9GBPS (1 << 2)
+# define DP_PCON_MAX_18GBPS (2 << 2)
+# define DP_PCON_MAX_24GBPS (3 << 2)
+# define DP_PCON_MAX_32GBPS (4 << 2)
+# define DP_PCON_MAX_40GBPS (5 << 2)
+# define DP_PCON_MAX_48GBPS (6 << 2)
+# define DP_PCON_SOURCE_CTL_MODE (1 << 5)
+
/* offset 3 for DVI */
# define DP_DS_DVI_DUAL_LINK (1 << 1)
# define DP_DS_DVI_HIGH_COLOR_DEPTH (1 << 2)
@@ -1054,6 +1065,51 @@ struct drm_device;
#define DP_CEC_TX_MESSAGE_BUFFER 0x3020
#define DP_CEC_MESSAGE_BUFFER_LENGTH 0x10
+/* PCON CONFIGURE-1 FRL FOR HDMI SINK */
+#define DP_PCON_HDMI_LINK_CONFIG_1 0x305A
+# define DP_PCON_ENABLE_MAX_FRL_BW (7 << 0)
+# define DP_PCON_ENABLE_MAX_BW_0GBPS 0
+# define DP_PCON_ENABLE_MAX_BW_9GBPS 1
+# define DP_PCON_ENABLE_MAX_BW_18GBPS 2
+# define DP_PCON_ENABLE_MAX_BW_24GBPS 3
+# define DP_PCON_ENABLE_MAX_BW_32GBPS 4
+# define DP_PCON_ENABLE_MAX_BW_40GBPS 5
+# define DP_PCON_ENABLE_MAX_BW_48GBPS 6
+# define DP_PCON_ENABLE_SOURCE_CTL_MODE (1 << 3)
+# define DP_PCON_ENABLE_CONCURRENT_LINK (1 << 4)
+# define DP_PCON_ENABLE_LINK_FRL_MODE (1 << 5)
+# define DP_PCON_ENABLE_HPD_READY (1 << 6)
+# define DP_PCON_ENABLE_HDMI_LINK (1 << 7)
+
+/* PCON CONFIGURE-2 FRL FOR HDMI SINK */
+#define DP_PCON_HDMI_LINK_CONFIG_2 0x305B
+# define DP_PCON_MAX_LINK_BW_MASK (0x3F << 0)
+# define DP_PCON_FRL_BW_MASK_9GBPS (1 << 0)
+# define DP_PCON_FRL_BW_MASK_18GBPS (1 << 1)
+# define DP_PCON_FRL_BW_MASK_24GBPS (1 << 2)
+# define DP_PCON_FRL_BW_MASK_32GBPS (1 << 3)
+# define DP_PCON_FRL_BW_MASK_40GBPS (1 << 4)
+# define DP_PCON_FRL_BW_MASK_48GBPS (1 << 5)
+# define DP_PCON_FRL_LINK_TRAIN_EXTENDED (1 << 6)
+
+/* PCON HDMI LINK STATUS */
+#define DP_PCON_HDMI_TX_LINK_STATUS 0x303B
+# define DP_PCON_HDMI_TX_LINK_ACTIVE (1 << 0)
+# define DP_PCON_FRL_READY (1 << 1)
+
+/* PCON HDMI POST FRL STATUS */
+#define DP_PCON_HDMI_POST_FRL_STATUS 0x3036
+# define DP_PCON_HDMI_LINK_MODE (1 << 0)
+# define DP_PCON_HDMI_MODE_TMDS 0
+# define DP_PCON_HDMI_MODE_FRL 1
+# define DP_PCON_HDMI_FRL_TRAINED_BW (0x3F << 1)
+# define DP_PCON_FRL_TRAINED_BW_9GBPS (1 << 1)
+# define DP_PCON_FRL_TRAINED_BW_18GBPS (1 << 2)
+# define DP_PCON_FRL_TRAINED_BW_24GBPS (1 << 3)
+# define DP_PCON_FRL_TRAINED_BW_32GBPS (1 << 4)
+# define DP_PCON_FRL_TRAINED_BW_40GBPS (1 << 5)
+# define DP_PCON_FRL_TRAINED_BW_48GBPS (1 << 6)
+
#define DP_PROTOCOL_CONVERTER_CONTROL_0 0x3050 /* DP 1.3 */
# define DP_HDMI_DVI_OUTPUT_CONFIG (1 << 0) /* DP 1.3 */
#define DP_PROTOCOL_CONVERTER_CONTROL_1 0x3051 /* DP 1.3 */
@@ -1967,4 +2023,18 @@ int drm_dp_get_phy_test_pattern(struct drm_dp_aux *aux,
struct drm_dp_phy_test_params *data);
int drm_dp_set_phy_test_pattern(struct drm_dp_aux *aux,
struct drm_dp_phy_test_params *data, u8 dp_rev);
+int drm_dp_get_pcon_max_frl_bw(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
+ const u8 port_cap[4]);
+int drm_dp_pcon_frl_prepare(struct drm_dp_aux *aux, bool enable_frl_ready_hpd);
+bool drm_dp_pcon_is_frl_ready(struct drm_dp_aux *aux);
+int drm_dp_pcon_frl_configure_1(struct drm_dp_aux *aux, int max_frl_gbps,
+ bool concurrent_mode);
+int drm_dp_pcon_frl_configure_2(struct drm_dp_aux *aux, int max_frl_mask,
+ bool extended_train_mode);
+int drm_dp_pcon_reset_frl_config(struct drm_dp_aux *aux);
+int drm_dp_pcon_frl_enable(struct drm_dp_aux *aux);
+
+bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux);
+int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask);
+
#endif /* _DRM_DP_HELPER_H_ */
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 05/15] drm/dp_helper: Add support for link failure detection
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
From: Swati Sharma <swati2.sharma@intel.com>
There are specific DPCDs defined for detecting link failures between
the PCON and HDMI sink and check the link status. In case of link
failure, PCON will communicate the same using an IRQ_HPD to source.
HDMI sink would have indicated the same to PCON using SCDC interrupt
mechanism. While source can always read final HDMI sink's status using
I2C over AUX, it is easier and faster to read the PCONs already read
HDMI sink status registers.
This patch adds the DPCDs required for link failure detection and
provide a helper function for printing error count/lane which might
help in debugging the link failure issues.
v2: Addressed comments from Uma Shankar:
-rephrased the commit message, as per the code.
-fixed styling issues
-added documentation for the helper function.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/drm_dp_helper.c | 39 +++++++++++++++++++++++++++++++++
include/drm/drm_dp_helper.h | 17 ++++++++++++++
2 files changed, 56 insertions(+)
diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c
index f501e3890921..a1d518b3a173 100644
--- a/drivers/gpu/drm/drm_dp_helper.c
+++ b/drivers/gpu/drm/drm_dp_helper.c
@@ -2859,3 +2859,42 @@ int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask)
return mode;
}
EXPORT_SYMBOL(drm_dp_pcon_hdmi_link_mode);
+
+/**
+ * drm_dp_pcon_hdmi_frl_link_error_count() - print the error count per lane
+ * during link failure between PCON and HDMI sink
+ * @aux: DisplayPort AUX channel
+ * @connector: DRM connector
+ * code.
+ **/
+
+void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
+ struct drm_connector *connector)
+{
+ u8 buf, error_count;
+ int i, num_error;
+ struct drm_hdmi_info *hdmi = &connector->display_info.hdmi;
+
+ for (i = 0; i < hdmi->max_lanes; i++) {
+ if (drm_dp_dpcd_readb(aux, DP_PCON_HDMI_ERROR_STATUS_LN0 + i, &buf) < 0)
+ return;
+
+ error_count = buf & DP_PCON_HDMI_ERROR_COUNT_MASK;
+ switch (error_count) {
+ case DP_PCON_HDMI_ERROR_COUNT_HUNDRED_PLUS:
+ num_error = 100;
+ break;
+ case DP_PCON_HDMI_ERROR_COUNT_TEN_PLUS:
+ num_error = 10;
+ break;
+ case DP_PCON_HDMI_ERROR_COUNT_THREE_PLUS:
+ num_error = 3;
+ break;
+ default:
+ num_error = 0;
+ }
+
+ DRM_ERROR("More than %d errors since the last read for lane %d", num_error, i);
+ }
+}
+EXPORT_SYMBOL(drm_dp_pcon_hdmi_frl_link_error_count);
diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
index c66f570eadc2..871e8c051642 100644
--- a/include/drm/drm_dp_helper.h
+++ b/include/drm/drm_dp_helper.h
@@ -946,6 +946,11 @@ struct drm_device;
# define DP_CEC_IRQ (1 << 2)
#define DP_LINK_SERVICE_IRQ_VECTOR_ESI0 0x2005 /* 1.2 */
+# define RX_CAP_CHANGED (1 << 0)
+# define LINK_STATUS_CHANGED (1 << 1)
+# define STREAM_STATUS_CHANGED (1 << 2)
+# define HDMI_LINK_STATUS_CHANGED (1 << 3)
+# define CONNECTED_OFF_ENTRY_REQUESTED (1 << 4)
#define DP_PSR_ERROR_STATUS 0x2006 /* XXX 1.2? */
# define DP_PSR_LINK_CRC_ERROR (1 << 0)
@@ -1120,6 +1125,16 @@ struct drm_device;
#define DP_PROTOCOL_CONVERTER_CONTROL_2 0x3052 /* DP 1.3 */
# define DP_CONVERSION_TO_YCBCR422_ENABLE (1 << 0) /* DP 1.3 */
+/* PCON Downstream HDMI ERROR Status per Lane */
+#define DP_PCON_HDMI_ERROR_STATUS_LN0 0x3037
+#define DP_PCON_HDMI_ERROR_STATUS_LN1 0x3038
+#define DP_PCON_HDMI_ERROR_STATUS_LN2 0x3039
+#define DP_PCON_HDMI_ERROR_STATUS_LN3 0x303A
+# define DP_PCON_HDMI_ERROR_COUNT_MASK (0x7 << 0)
+# define DP_PCON_HDMI_ERROR_COUNT_THREE_PLUS (1 << 0)
+# define DP_PCON_HDMI_ERROR_COUNT_TEN_PLUS (1 << 1)
+# define DP_PCON_HDMI_ERROR_COUNT_HUNDRED_PLUS (1 << 2)
+
/* HDCP 1.3 and HDCP 2.2 */
#define DP_AUX_HDCP_BKSV 0x68000
#define DP_AUX_HDCP_RI_PRIME 0x68005
@@ -2036,5 +2051,7 @@ int drm_dp_pcon_frl_enable(struct drm_dp_aux *aux);
bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux);
int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask);
+void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
+ struct drm_connector *connector);
#endif /* _DRM_DP_HELPER_H_ */
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 05/15] drm/dp_helper: Add support for link failure detection
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
From: Swati Sharma <swati2.sharma@intel.com>
There are specific DPCDs defined for detecting link failures between
the PCON and HDMI sink and check the link status. In case of link
failure, PCON will communicate the same using an IRQ_HPD to source.
HDMI sink would have indicated the same to PCON using SCDC interrupt
mechanism. While source can always read final HDMI sink's status using
I2C over AUX, it is easier and faster to read the PCONs already read
HDMI sink status registers.
This patch adds the DPCDs required for link failure detection and
provide a helper function for printing error count/lane which might
help in debugging the link failure issues.
v2: Addressed comments from Uma Shankar:
-rephrased the commit message, as per the code.
-fixed styling issues
-added documentation for the helper function.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/drm_dp_helper.c | 39 +++++++++++++++++++++++++++++++++
include/drm/drm_dp_helper.h | 17 ++++++++++++++
2 files changed, 56 insertions(+)
diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c
index f501e3890921..a1d518b3a173 100644
--- a/drivers/gpu/drm/drm_dp_helper.c
+++ b/drivers/gpu/drm/drm_dp_helper.c
@@ -2859,3 +2859,42 @@ int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask)
return mode;
}
EXPORT_SYMBOL(drm_dp_pcon_hdmi_link_mode);
+
+/**
+ * drm_dp_pcon_hdmi_frl_link_error_count() - print the error count per lane
+ * during link failure between PCON and HDMI sink
+ * @aux: DisplayPort AUX channel
+ * @connector: DRM connector
+ * code.
+ **/
+
+void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
+ struct drm_connector *connector)
+{
+ u8 buf, error_count;
+ int i, num_error;
+ struct drm_hdmi_info *hdmi = &connector->display_info.hdmi;
+
+ for (i = 0; i < hdmi->max_lanes; i++) {
+ if (drm_dp_dpcd_readb(aux, DP_PCON_HDMI_ERROR_STATUS_LN0 + i, &buf) < 0)
+ return;
+
+ error_count = buf & DP_PCON_HDMI_ERROR_COUNT_MASK;
+ switch (error_count) {
+ case DP_PCON_HDMI_ERROR_COUNT_HUNDRED_PLUS:
+ num_error = 100;
+ break;
+ case DP_PCON_HDMI_ERROR_COUNT_TEN_PLUS:
+ num_error = 10;
+ break;
+ case DP_PCON_HDMI_ERROR_COUNT_THREE_PLUS:
+ num_error = 3;
+ break;
+ default:
+ num_error = 0;
+ }
+
+ DRM_ERROR("More than %d errors since the last read for lane %d", num_error, i);
+ }
+}
+EXPORT_SYMBOL(drm_dp_pcon_hdmi_frl_link_error_count);
diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
index c66f570eadc2..871e8c051642 100644
--- a/include/drm/drm_dp_helper.h
+++ b/include/drm/drm_dp_helper.h
@@ -946,6 +946,11 @@ struct drm_device;
# define DP_CEC_IRQ (1 << 2)
#define DP_LINK_SERVICE_IRQ_VECTOR_ESI0 0x2005 /* 1.2 */
+# define RX_CAP_CHANGED (1 << 0)
+# define LINK_STATUS_CHANGED (1 << 1)
+# define STREAM_STATUS_CHANGED (1 << 2)
+# define HDMI_LINK_STATUS_CHANGED (1 << 3)
+# define CONNECTED_OFF_ENTRY_REQUESTED (1 << 4)
#define DP_PSR_ERROR_STATUS 0x2006 /* XXX 1.2? */
# define DP_PSR_LINK_CRC_ERROR (1 << 0)
@@ -1120,6 +1125,16 @@ struct drm_device;
#define DP_PROTOCOL_CONVERTER_CONTROL_2 0x3052 /* DP 1.3 */
# define DP_CONVERSION_TO_YCBCR422_ENABLE (1 << 0) /* DP 1.3 */
+/* PCON Downstream HDMI ERROR Status per Lane */
+#define DP_PCON_HDMI_ERROR_STATUS_LN0 0x3037
+#define DP_PCON_HDMI_ERROR_STATUS_LN1 0x3038
+#define DP_PCON_HDMI_ERROR_STATUS_LN2 0x3039
+#define DP_PCON_HDMI_ERROR_STATUS_LN3 0x303A
+# define DP_PCON_HDMI_ERROR_COUNT_MASK (0x7 << 0)
+# define DP_PCON_HDMI_ERROR_COUNT_THREE_PLUS (1 << 0)
+# define DP_PCON_HDMI_ERROR_COUNT_TEN_PLUS (1 << 1)
+# define DP_PCON_HDMI_ERROR_COUNT_HUNDRED_PLUS (1 << 2)
+
/* HDCP 1.3 and HDCP 2.2 */
#define DP_AUX_HDCP_BKSV 0x68000
#define DP_AUX_HDCP_RI_PRIME 0x68005
@@ -2036,5 +2051,7 @@ int drm_dp_pcon_frl_enable(struct drm_dp_aux *aux);
bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux);
int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask);
+void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
+ struct drm_connector *connector);
#endif /* _DRM_DP_HELPER_H_ */
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 06/15] drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
This patch adds registers for getting DSC encoder capability for
a HDMI2.1 PCon. It also addes helper functions to configure
DSC between the PCON and HDMI2.1 sink.
v2: Corrected offset for DSC encoder bpc and minor changes.
Also added helper functions for getting pcon dsc encoder capabilities
as suggested by Uma Shankar.
v3: Only setting the DSC bits for the Protocol Convertor control
registers, avoiding overwritining color conversion bits.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
---
drivers/gpu/drm/drm_dp_helper.c | 203 ++++++++++++++++++++++++++++++++
include/drm/drm_dp_helper.h | 114 ++++++++++++++++++
2 files changed, 317 insertions(+)
diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c
index a1d518b3a173..689fd0d5f6c5 100644
--- a/drivers/gpu/drm/drm_dp_helper.c
+++ b/drivers/gpu/drm/drm_dp_helper.c
@@ -2898,3 +2898,206 @@ void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
}
}
EXPORT_SYMBOL(drm_dp_pcon_hdmi_frl_link_error_count);
+
+/*
+ * drm_dp_pcon_enc_is_dsc_1_2 - Does PCON Encoder supports DSC 1.2
+ * @pcon_dsc_dpcd: DSC capabilities of the PCON DSC Encoder
+ *
+ * Returns true is PCON encoder is DSC 1.2 else returns false.
+ */
+bool drm_dp_pcon_enc_is_dsc_1_2(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE])
+{
+ u8 buf;
+ u8 major_v, minor_v;
+
+ buf = pcon_dsc_dpcd[DP_PCON_DSC_VERSION - DP_PCON_DSC_ENCODER];
+ major_v = (buf & DP_PCON_DSC_MAJOR_MASK) >> DP_PCON_DSC_MAJOR_SHIFT;
+ minor_v = (buf & DP_PCON_DSC_MINOR_MASK) >> DP_PCON_DSC_MINOR_SHIFT;
+
+ if (major_v == 1 && minor_v == 2)
+ return true;
+
+ return false;
+}
+EXPORT_SYMBOL(drm_dp_pcon_enc_is_dsc_1_2);
+
+/*
+ * drm_dp_pcon_dsc_max_slices - Get max slices supported by PCON DSC Encoder
+ * @pcon_dsc_dpcd: DSC capabilities of the PCON DSC Encoder
+ *
+ * Returns maximum no. of slices supported by the PCON DSC Encoder.
+ */
+int drm_dp_pcon_dsc_max_slices(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE])
+{
+ u8 slice_cap1, slice_cap2;
+
+ slice_cap1 = pcon_dsc_dpcd[DP_PCON_DSC_SLICE_CAP_1 - DP_PCON_DSC_ENCODER];
+ slice_cap2 = pcon_dsc_dpcd[DP_PCON_DSC_SLICE_CAP_2 - DP_PCON_DSC_ENCODER];
+
+ if (slice_cap2 & DP_PCON_DSC_24_PER_DSC_ENC)
+ return 24;
+ if (slice_cap2 & DP_PCON_DSC_20_PER_DSC_ENC)
+ return 20;
+ if (slice_cap2 & DP_PCON_DSC_16_PER_DSC_ENC)
+ return 16;
+ if (slice_cap1 & DP_PCON_DSC_12_PER_DSC_ENC)
+ return 12;
+ if (slice_cap1 & DP_PCON_DSC_10_PER_DSC_ENC)
+ return 10;
+ if (slice_cap1 & DP_PCON_DSC_8_PER_DSC_ENC)
+ return 8;
+ if (slice_cap1 & DP_PCON_DSC_6_PER_DSC_ENC)
+ return 6;
+ if (slice_cap1 & DP_PCON_DSC_4_PER_DSC_ENC)
+ return 4;
+ if (slice_cap1 & DP_PCON_DSC_2_PER_DSC_ENC)
+ return 2;
+ if (slice_cap1 & DP_PCON_DSC_1_PER_DSC_ENC)
+ return 1;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_dsc_max_slices);
+
+/*
+ * drm_dp_pcon_dsc_max_slice_width() - Get max slice width for Pcon DSC encoder
+ * @pcon_dsc_dpcd: DSC capabilities of the PCON DSC Encoder
+ *
+ * Returns maximum width of the slices in pixel width i.e. no. of pixels x 320.
+ */
+int drm_dp_pcon_dsc_max_slice_width(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE])
+{
+ u8 buf;
+
+ buf = pcon_dsc_dpcd[DP_PCON_DSC_MAX_SLICE_WIDTH - DP_PCON_DSC_ENCODER];
+
+ return buf * DP_DSC_SLICE_WIDTH_MULTIPLIER;
+}
+EXPORT_SYMBOL(drm_dp_pcon_dsc_max_slice_width);
+
+/*
+ * drm_dp_pcon_dsc_bpp_incr() - Get bits per pixel increment for PCON DSC encoder
+ * @pcon_dsc_dpcd: DSC capabilities of the PCON DSC Encoder
+ *
+ * Returns the bpp precision supported by the PCON encoder.
+ */
+int drm_dp_pcon_dsc_bpp_incr(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE])
+{
+ u8 buf;
+
+ buf = pcon_dsc_dpcd[DP_PCON_DSC_BPP_INCR - DP_PCON_DSC_ENCODER];
+
+ switch (buf & DP_PCON_DSC_BPP_INCR_MASK) {
+ case DP_PCON_DSC_ONE_16TH_BPP:
+ return 16;
+ case DP_PCON_DSC_ONE_8TH_BPP:
+ return 8;
+ case DP_PCON_DSC_ONE_4TH_BPP:
+ return 4;
+ case DP_PCON_DSC_ONE_HALF_BPP:
+ return 2;
+ case DP_PCON_DSC_ONE_BPP:
+ return 1;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_dsc_bpp_incr);
+
+static
+int drm_dp_pcon_configure_dsc_enc(struct drm_dp_aux *aux, u8 pps_buf_config)
+{
+ u8 buf;
+ int ret;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PROTOCOL_CONVERTER_CONTROL_2, &buf);
+ if (ret < 0)
+ return ret;
+
+ buf |= DP_PCON_ENABLE_DSC_ENCODER;
+
+ if (pps_buf_config <= DP_PCON_ENC_PPS_OVERRIDE_EN_BUFFER) {
+ buf &= ~DP_PCON_ENCODER_PPS_OVERRIDE_MASK;
+ buf |= pps_buf_config << 2;
+ }
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PROTOCOL_CONVERTER_CONTROL_2, buf);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+/**
+ * drm_dp_pcon_pps_default() - Let PCON fill the default pps parameters
+ * for DSC1.2 between PCON & HDMI2.1 sink
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns 0 on success, else returns negative error code.
+ * */
+int drm_dp_pcon_pps_default(struct drm_dp_aux *aux)
+{
+ int ret;
+
+ ret = drm_dp_pcon_configure_dsc_enc(aux, DP_PCON_ENC_PPS_OVERRIDE_DISABLED);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_pps_default);
+
+/**
+ * drm_dp_pcon_pps_override_buf() - Configure PPS encoder override buffer for
+ * HDMI sink
+ * @aux: DisplayPort AUX channel
+ * @pps_buf: 128 bytes to be written into PPS buffer for HDMI sink by PCON.
+ *
+ * Returns 0 on success, else returns negative error code.
+ * */
+int drm_dp_pcon_pps_override_buf(struct drm_dp_aux *aux, u8 pps_buf[128])
+{
+ int ret;
+
+ ret = drm_dp_dpcd_write(aux, DP_PCON_HDMI_PPS_OVERRIDE_BASE, &pps_buf, 128);
+ if (ret < 0)
+ return ret;
+
+ ret = drm_dp_pcon_configure_dsc_enc(aux, DP_PCON_ENC_PPS_OVERRIDE_EN_BUFFER);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_pps_override_buf);
+
+/*
+ * drm_dp_pcon_pps_override_param() - Write PPS parameters to DSC encoder
+ * override registers
+ * @aux: DisplayPort AUX channel
+ * @pps_param: 3 Parameters (2 Bytes each) : Slice Width, Slice Height,
+ * bits_per_pixel.
+ *
+ * Returns 0 on success, else returns negative error code.
+ * */
+int drm_dp_pcon_pps_override_param(struct drm_dp_aux *aux, u8 pps_param[6])
+{
+ int ret;
+
+ ret = drm_dp_dpcd_write(aux, DP_PCON_HDMI_PPS_OVRD_SLICE_HEIGHT, &pps_param[0], 2);
+ if (ret < 0)
+ return ret;
+ ret = drm_dp_dpcd_write(aux, DP_PCON_HDMI_PPS_OVRD_SLICE_WIDTH, &pps_param[2], 2);
+ if (ret < 0)
+ return ret;
+ ret = drm_dp_dpcd_write(aux, DP_PCON_HDMI_PPS_OVRD_BPP, &pps_param[4], 2);
+ if (ret < 0)
+ return ret;
+
+ ret = drm_dp_pcon_configure_dsc_enc(aux, DP_PCON_ENC_PPS_OVERRIDE_EN_BUFFER);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_pps_override_param);
diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
index 871e8c051642..baad87fe6b0a 100644
--- a/include/drm/drm_dp_helper.h
+++ b/include/drm/drm_dp_helper.h
@@ -441,6 +441,84 @@ struct drm_device;
# define DP_FEC_CORR_BLK_ERROR_COUNT_CAP (1 << 2)
# define DP_FEC_BIT_ERROR_COUNT_CAP (1 << 3)
+/* DP-HDMI2.1 PCON DSC ENCODER SUPPORT */
+#define DP_PCON_DSC_ENCODER_CAP_SIZE 0xC /* 0x9E - 0x92 */
+#define DP_PCON_DSC_ENCODER 0x092
+# define DP_PCON_DSC_ENCODER_SUPPORTED (1 << 0)
+# define DP_PCON_DSC_PPS_ENC_OVERRIDE (1 << 1)
+
+/* DP-HDMI2.1 PCON DSC Version */
+#define DP_PCON_DSC_VERSION 0x093
+# define DP_PCON_DSC_MAJOR_MASK (0xF << 0)
+# define DP_PCON_DSC_MINOR_MASK (0xF << 4)
+# define DP_PCON_DSC_MAJOR_SHIFT 0
+# define DP_PCON_DSC_MINOR_SHIFT 4
+
+/* DP-HDMI2.1 PCON DSC RC Buffer block size */
+#define DP_PCON_DSC_RC_BUF_BLK_INFO 0x094
+# define DP_PCON_DSC_RC_BUF_BLK_SIZE (0x3 << 0)
+# define DP_PCON_DSC_RC_BUF_BLK_1KB 0
+# define DP_PCON_DSC_RC_BUF_BLK_4KB 1
+# define DP_PCON_DSC_RC_BUF_BLK_16KB 2
+# define DP_PCON_DSC_RC_BUF_BLK_64KB 3
+
+/* DP-HDMI2.1 PCON DSC RC Buffer size */
+#define DP_PCON_DSC_RC_BUF_SIZE 0x095
+
+/* DP-HDMI2.1 PCON DSC Slice capabilities-1 */
+#define DP_PCON_DSC_SLICE_CAP_1 0x096
+# define DP_PCON_DSC_1_PER_DSC_ENC (0x1 << 0)
+# define DP_PCON_DSC_2_PER_DSC_ENC (0x1 << 1)
+# define DP_PCON_DSC_4_PER_DSC_ENC (0x1 << 3)
+# define DP_PCON_DSC_6_PER_DSC_ENC (0x1 << 4)
+# define DP_PCON_DSC_8_PER_DSC_ENC (0x1 << 5)
+# define DP_PCON_DSC_10_PER_DSC_ENC (0x1 << 6)
+# define DP_PCON_DSC_12_PER_DSC_ENC (0x1 << 7)
+
+#define DP_PCON_DSC_BUF_BIT_DEPTH 0x097
+# define DP_PCON_DSC_BIT_DEPTH_MASK (0xF << 0)
+# define DP_PCON_DSC_DEPTH_9_BITS 0
+# define DP_PCON_DSC_DEPTH_10_BITS 1
+# define DP_PCON_DSC_DEPTH_11_BITS 2
+# define DP_PCON_DSC_DEPTH_12_BITS 3
+# define DP_PCON_DSC_DEPTH_13_BITS 4
+# define DP_PCON_DSC_DEPTH_14_BITS 5
+# define DP_PCON_DSC_DEPTH_15_BITS 6
+# define DP_PCON_DSC_DEPTH_16_BITS 7
+# define DP_PCON_DSC_DEPTH_8_BITS 8
+
+#define DP_PCON_DSC_BLOCK_PREDICTION 0x098
+# define DP_PCON_DSC_BLOCK_PRED_SUPPORT (0x1 << 0)
+
+#define DP_PCON_DSC_ENC_COLOR_FMT_CAP 0x099
+# define DP_PCON_DSC_ENC_RGB (0x1 << 0)
+# define DP_PCON_DSC_ENC_YUV444 (0x1 << 1)
+# define DP_PCON_DSC_ENC_YUV422_S (0x1 << 2)
+# define DP_PCON_DSC_ENC_YUV422_N (0x1 << 3)
+# define DP_PCON_DSC_ENC_YUV420_N (0x1 << 4)
+
+#define DP_PCON_DSC_ENC_COLOR_DEPTH_CAP 0x09A
+# define DP_PCON_DSC_ENC_8BPC (0x1 << 1)
+# define DP_PCON_DSC_ENC_10BPC (0x1 << 2)
+# define DP_PCON_DSC_ENC_12BPC (0x1 << 3)
+
+#define DP_PCON_DSC_MAX_SLICE_WIDTH 0x09B
+
+/* DP-HDMI2.1 PCON DSC Slice capabilities-2 */
+#define DP_PCON_DSC_SLICE_CAP_2 0x09C
+# define DP_PCON_DSC_16_PER_DSC_ENC (0x1 << 0)
+# define DP_PCON_DSC_20_PER_DSC_ENC (0x1 << 1)
+# define DP_PCON_DSC_24_PER_DSC_ENC (0x1 << 2)
+
+/* DP-HDMI2.1 PCON HDMI TX Encoder Bits/pixel increment */
+#define DP_PCON_DSC_BPP_INCR 0x09E
+# define DP_PCON_DSC_BPP_INCR_MASK (0x7 << 0)
+# define DP_PCON_DSC_ONE_16TH_BPP 0
+# define DP_PCON_DSC_ONE_8TH_BPP 1
+# define DP_PCON_DSC_ONE_4TH_BPP 2
+# define DP_PCON_DSC_ONE_HALF_BPP 3
+# define DP_PCON_DSC_ONE_BPP 4
+
/* DP Extended DSC Capabilities */
#define DP_DSC_BRANCH_OVERALL_THROUGHPUT_0 0x0a0 /* DP 1.4a SCR */
#define DP_DSC_BRANCH_OVERALL_THROUGHPUT_1 0x0a1
@@ -1124,6 +1202,12 @@ struct drm_device;
# define DP_HDMI_FORCE_SCRAMBLING (1 << 3) /* DP 1.4 */
#define DP_PROTOCOL_CONVERTER_CONTROL_2 0x3052 /* DP 1.3 */
# define DP_CONVERSION_TO_YCBCR422_ENABLE (1 << 0) /* DP 1.3 */
+# define DP_PCON_ENABLE_DSC_ENCODER (1 << 1)
+# define DP_PCON_ENCODER_PPS_OVERRIDE_MASK (0x3 << 2)
+# define DP_PCON_ENC_PPS_OVERRIDE_DISABLED 0
+# define DP_PCON_ENC_PPS_OVERRIDE_EN_PARAMS 1
+# define DP_PCON_ENC_PPS_OVERRIDE_EN_BUFFER 2
+
/* PCON Downstream HDMI ERROR Status per Lane */
#define DP_PCON_HDMI_ERROR_STATUS_LN0 0x3037
@@ -1135,6 +1219,29 @@ struct drm_device;
# define DP_PCON_HDMI_ERROR_COUNT_TEN_PLUS (1 << 1)
# define DP_PCON_HDMI_ERROR_COUNT_HUNDRED_PLUS (1 << 2)
+/* PCON HDMI CONFIG PPS Override Buffer
+ * Valid Offsets to be added to Base : 0-127
+ */
+#define DP_PCON_HDMI_PPS_OVERRIDE_BASE 0x3100
+
+/* PCON HDMI CONFIG PPS Override Parameter: Slice height
+ * Offset-0 8LSBs of the Slice height.
+ * Offset-1 8MSBs of the Slice height.
+ */
+#define DP_PCON_HDMI_PPS_OVRD_SLICE_HEIGHT 0x3180
+
+/* PCON HDMI CONFIG PPS Override Parameter: Slice width
+ * Offset-0 8LSBs of the Slice width.
+ * Offset-1 8MSBs of the Slice width.
+ */
+#define DP_PCON_HDMI_PPS_OVRD_SLICE_WIDTH 0x3182
+
+/* PCON HDMI CONFIG PPS Override Parameter: bits_per_pixel
+ * Offset-0 8LSBs of the bits_per_pixel.
+ * Offset-1 2MSBs of the bits_per_pixel.
+ */
+#define DP_PCON_HDMI_PPS_OVRD_BPP 0x3184
+
/* HDCP 1.3 and HDCP 2.2 */
#define DP_AUX_HDCP_BKSV 0x68000
#define DP_AUX_HDCP_RI_PRIME 0x68005
@@ -2053,5 +2160,12 @@ bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux);
int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask);
void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
struct drm_connector *connector);
+bool drm_dp_pcon_enc_is_dsc_1_2(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]);
+int drm_dp_pcon_dsc_max_slices(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]);
+int drm_dp_pcon_dsc_max_slice_width(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]);
+int drm_dp_pcon_dsc_bpp_incr(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]);
+int drm_dp_pcon_pps_default(struct drm_dp_aux *aux);
+int drm_dp_pcon_pps_override_buf(struct drm_dp_aux *aux, u8 pps_buf[128]);
+int drm_dp_pcon_pps_override_param(struct drm_dp_aux *aux, u8 pps_param[6]);
#endif /* _DRM_DP_HELPER_H_ */
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 06/15] drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
This patch adds registers for getting DSC encoder capability for
a HDMI2.1 PCon. It also addes helper functions to configure
DSC between the PCON and HDMI2.1 sink.
v2: Corrected offset for DSC encoder bpc and minor changes.
Also added helper functions for getting pcon dsc encoder capabilities
as suggested by Uma Shankar.
v3: Only setting the DSC bits for the Protocol Convertor control
registers, avoiding overwritining color conversion bits.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
---
drivers/gpu/drm/drm_dp_helper.c | 203 ++++++++++++++++++++++++++++++++
include/drm/drm_dp_helper.h | 114 ++++++++++++++++++
2 files changed, 317 insertions(+)
diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c
index a1d518b3a173..689fd0d5f6c5 100644
--- a/drivers/gpu/drm/drm_dp_helper.c
+++ b/drivers/gpu/drm/drm_dp_helper.c
@@ -2898,3 +2898,206 @@ void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
}
}
EXPORT_SYMBOL(drm_dp_pcon_hdmi_frl_link_error_count);
+
+/*
+ * drm_dp_pcon_enc_is_dsc_1_2 - Does PCON Encoder supports DSC 1.2
+ * @pcon_dsc_dpcd: DSC capabilities of the PCON DSC Encoder
+ *
+ * Returns true is PCON encoder is DSC 1.2 else returns false.
+ */
+bool drm_dp_pcon_enc_is_dsc_1_2(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE])
+{
+ u8 buf;
+ u8 major_v, minor_v;
+
+ buf = pcon_dsc_dpcd[DP_PCON_DSC_VERSION - DP_PCON_DSC_ENCODER];
+ major_v = (buf & DP_PCON_DSC_MAJOR_MASK) >> DP_PCON_DSC_MAJOR_SHIFT;
+ minor_v = (buf & DP_PCON_DSC_MINOR_MASK) >> DP_PCON_DSC_MINOR_SHIFT;
+
+ if (major_v == 1 && minor_v == 2)
+ return true;
+
+ return false;
+}
+EXPORT_SYMBOL(drm_dp_pcon_enc_is_dsc_1_2);
+
+/*
+ * drm_dp_pcon_dsc_max_slices - Get max slices supported by PCON DSC Encoder
+ * @pcon_dsc_dpcd: DSC capabilities of the PCON DSC Encoder
+ *
+ * Returns maximum no. of slices supported by the PCON DSC Encoder.
+ */
+int drm_dp_pcon_dsc_max_slices(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE])
+{
+ u8 slice_cap1, slice_cap2;
+
+ slice_cap1 = pcon_dsc_dpcd[DP_PCON_DSC_SLICE_CAP_1 - DP_PCON_DSC_ENCODER];
+ slice_cap2 = pcon_dsc_dpcd[DP_PCON_DSC_SLICE_CAP_2 - DP_PCON_DSC_ENCODER];
+
+ if (slice_cap2 & DP_PCON_DSC_24_PER_DSC_ENC)
+ return 24;
+ if (slice_cap2 & DP_PCON_DSC_20_PER_DSC_ENC)
+ return 20;
+ if (slice_cap2 & DP_PCON_DSC_16_PER_DSC_ENC)
+ return 16;
+ if (slice_cap1 & DP_PCON_DSC_12_PER_DSC_ENC)
+ return 12;
+ if (slice_cap1 & DP_PCON_DSC_10_PER_DSC_ENC)
+ return 10;
+ if (slice_cap1 & DP_PCON_DSC_8_PER_DSC_ENC)
+ return 8;
+ if (slice_cap1 & DP_PCON_DSC_6_PER_DSC_ENC)
+ return 6;
+ if (slice_cap1 & DP_PCON_DSC_4_PER_DSC_ENC)
+ return 4;
+ if (slice_cap1 & DP_PCON_DSC_2_PER_DSC_ENC)
+ return 2;
+ if (slice_cap1 & DP_PCON_DSC_1_PER_DSC_ENC)
+ return 1;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_dsc_max_slices);
+
+/*
+ * drm_dp_pcon_dsc_max_slice_width() - Get max slice width for Pcon DSC encoder
+ * @pcon_dsc_dpcd: DSC capabilities of the PCON DSC Encoder
+ *
+ * Returns maximum width of the slices in pixel width i.e. no. of pixels x 320.
+ */
+int drm_dp_pcon_dsc_max_slice_width(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE])
+{
+ u8 buf;
+
+ buf = pcon_dsc_dpcd[DP_PCON_DSC_MAX_SLICE_WIDTH - DP_PCON_DSC_ENCODER];
+
+ return buf * DP_DSC_SLICE_WIDTH_MULTIPLIER;
+}
+EXPORT_SYMBOL(drm_dp_pcon_dsc_max_slice_width);
+
+/*
+ * drm_dp_pcon_dsc_bpp_incr() - Get bits per pixel increment for PCON DSC encoder
+ * @pcon_dsc_dpcd: DSC capabilities of the PCON DSC Encoder
+ *
+ * Returns the bpp precision supported by the PCON encoder.
+ */
+int drm_dp_pcon_dsc_bpp_incr(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE])
+{
+ u8 buf;
+
+ buf = pcon_dsc_dpcd[DP_PCON_DSC_BPP_INCR - DP_PCON_DSC_ENCODER];
+
+ switch (buf & DP_PCON_DSC_BPP_INCR_MASK) {
+ case DP_PCON_DSC_ONE_16TH_BPP:
+ return 16;
+ case DP_PCON_DSC_ONE_8TH_BPP:
+ return 8;
+ case DP_PCON_DSC_ONE_4TH_BPP:
+ return 4;
+ case DP_PCON_DSC_ONE_HALF_BPP:
+ return 2;
+ case DP_PCON_DSC_ONE_BPP:
+ return 1;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_dsc_bpp_incr);
+
+static
+int drm_dp_pcon_configure_dsc_enc(struct drm_dp_aux *aux, u8 pps_buf_config)
+{
+ u8 buf;
+ int ret;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PROTOCOL_CONVERTER_CONTROL_2, &buf);
+ if (ret < 0)
+ return ret;
+
+ buf |= DP_PCON_ENABLE_DSC_ENCODER;
+
+ if (pps_buf_config <= DP_PCON_ENC_PPS_OVERRIDE_EN_BUFFER) {
+ buf &= ~DP_PCON_ENCODER_PPS_OVERRIDE_MASK;
+ buf |= pps_buf_config << 2;
+ }
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PROTOCOL_CONVERTER_CONTROL_2, buf);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+/**
+ * drm_dp_pcon_pps_default() - Let PCON fill the default pps parameters
+ * for DSC1.2 between PCON & HDMI2.1 sink
+ * @aux: DisplayPort AUX channel
+ *
+ * Returns 0 on success, else returns negative error code.
+ * */
+int drm_dp_pcon_pps_default(struct drm_dp_aux *aux)
+{
+ int ret;
+
+ ret = drm_dp_pcon_configure_dsc_enc(aux, DP_PCON_ENC_PPS_OVERRIDE_DISABLED);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_pps_default);
+
+/**
+ * drm_dp_pcon_pps_override_buf() - Configure PPS encoder override buffer for
+ * HDMI sink
+ * @aux: DisplayPort AUX channel
+ * @pps_buf: 128 bytes to be written into PPS buffer for HDMI sink by PCON.
+ *
+ * Returns 0 on success, else returns negative error code.
+ * */
+int drm_dp_pcon_pps_override_buf(struct drm_dp_aux *aux, u8 pps_buf[128])
+{
+ int ret;
+
+ ret = drm_dp_dpcd_write(aux, DP_PCON_HDMI_PPS_OVERRIDE_BASE, &pps_buf, 128);
+ if (ret < 0)
+ return ret;
+
+ ret = drm_dp_pcon_configure_dsc_enc(aux, DP_PCON_ENC_PPS_OVERRIDE_EN_BUFFER);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_pps_override_buf);
+
+/*
+ * drm_dp_pcon_pps_override_param() - Write PPS parameters to DSC encoder
+ * override registers
+ * @aux: DisplayPort AUX channel
+ * @pps_param: 3 Parameters (2 Bytes each) : Slice Width, Slice Height,
+ * bits_per_pixel.
+ *
+ * Returns 0 on success, else returns negative error code.
+ * */
+int drm_dp_pcon_pps_override_param(struct drm_dp_aux *aux, u8 pps_param[6])
+{
+ int ret;
+
+ ret = drm_dp_dpcd_write(aux, DP_PCON_HDMI_PPS_OVRD_SLICE_HEIGHT, &pps_param[0], 2);
+ if (ret < 0)
+ return ret;
+ ret = drm_dp_dpcd_write(aux, DP_PCON_HDMI_PPS_OVRD_SLICE_WIDTH, &pps_param[2], 2);
+ if (ret < 0)
+ return ret;
+ ret = drm_dp_dpcd_write(aux, DP_PCON_HDMI_PPS_OVRD_BPP, &pps_param[4], 2);
+ if (ret < 0)
+ return ret;
+
+ ret = drm_dp_pcon_configure_dsc_enc(aux, DP_PCON_ENC_PPS_OVERRIDE_EN_BUFFER);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_pps_override_param);
diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
index 871e8c051642..baad87fe6b0a 100644
--- a/include/drm/drm_dp_helper.h
+++ b/include/drm/drm_dp_helper.h
@@ -441,6 +441,84 @@ struct drm_device;
# define DP_FEC_CORR_BLK_ERROR_COUNT_CAP (1 << 2)
# define DP_FEC_BIT_ERROR_COUNT_CAP (1 << 3)
+/* DP-HDMI2.1 PCON DSC ENCODER SUPPORT */
+#define DP_PCON_DSC_ENCODER_CAP_SIZE 0xC /* 0x9E - 0x92 */
+#define DP_PCON_DSC_ENCODER 0x092
+# define DP_PCON_DSC_ENCODER_SUPPORTED (1 << 0)
+# define DP_PCON_DSC_PPS_ENC_OVERRIDE (1 << 1)
+
+/* DP-HDMI2.1 PCON DSC Version */
+#define DP_PCON_DSC_VERSION 0x093
+# define DP_PCON_DSC_MAJOR_MASK (0xF << 0)
+# define DP_PCON_DSC_MINOR_MASK (0xF << 4)
+# define DP_PCON_DSC_MAJOR_SHIFT 0
+# define DP_PCON_DSC_MINOR_SHIFT 4
+
+/* DP-HDMI2.1 PCON DSC RC Buffer block size */
+#define DP_PCON_DSC_RC_BUF_BLK_INFO 0x094
+# define DP_PCON_DSC_RC_BUF_BLK_SIZE (0x3 << 0)
+# define DP_PCON_DSC_RC_BUF_BLK_1KB 0
+# define DP_PCON_DSC_RC_BUF_BLK_4KB 1
+# define DP_PCON_DSC_RC_BUF_BLK_16KB 2
+# define DP_PCON_DSC_RC_BUF_BLK_64KB 3
+
+/* DP-HDMI2.1 PCON DSC RC Buffer size */
+#define DP_PCON_DSC_RC_BUF_SIZE 0x095
+
+/* DP-HDMI2.1 PCON DSC Slice capabilities-1 */
+#define DP_PCON_DSC_SLICE_CAP_1 0x096
+# define DP_PCON_DSC_1_PER_DSC_ENC (0x1 << 0)
+# define DP_PCON_DSC_2_PER_DSC_ENC (0x1 << 1)
+# define DP_PCON_DSC_4_PER_DSC_ENC (0x1 << 3)
+# define DP_PCON_DSC_6_PER_DSC_ENC (0x1 << 4)
+# define DP_PCON_DSC_8_PER_DSC_ENC (0x1 << 5)
+# define DP_PCON_DSC_10_PER_DSC_ENC (0x1 << 6)
+# define DP_PCON_DSC_12_PER_DSC_ENC (0x1 << 7)
+
+#define DP_PCON_DSC_BUF_BIT_DEPTH 0x097
+# define DP_PCON_DSC_BIT_DEPTH_MASK (0xF << 0)
+# define DP_PCON_DSC_DEPTH_9_BITS 0
+# define DP_PCON_DSC_DEPTH_10_BITS 1
+# define DP_PCON_DSC_DEPTH_11_BITS 2
+# define DP_PCON_DSC_DEPTH_12_BITS 3
+# define DP_PCON_DSC_DEPTH_13_BITS 4
+# define DP_PCON_DSC_DEPTH_14_BITS 5
+# define DP_PCON_DSC_DEPTH_15_BITS 6
+# define DP_PCON_DSC_DEPTH_16_BITS 7
+# define DP_PCON_DSC_DEPTH_8_BITS 8
+
+#define DP_PCON_DSC_BLOCK_PREDICTION 0x098
+# define DP_PCON_DSC_BLOCK_PRED_SUPPORT (0x1 << 0)
+
+#define DP_PCON_DSC_ENC_COLOR_FMT_CAP 0x099
+# define DP_PCON_DSC_ENC_RGB (0x1 << 0)
+# define DP_PCON_DSC_ENC_YUV444 (0x1 << 1)
+# define DP_PCON_DSC_ENC_YUV422_S (0x1 << 2)
+# define DP_PCON_DSC_ENC_YUV422_N (0x1 << 3)
+# define DP_PCON_DSC_ENC_YUV420_N (0x1 << 4)
+
+#define DP_PCON_DSC_ENC_COLOR_DEPTH_CAP 0x09A
+# define DP_PCON_DSC_ENC_8BPC (0x1 << 1)
+# define DP_PCON_DSC_ENC_10BPC (0x1 << 2)
+# define DP_PCON_DSC_ENC_12BPC (0x1 << 3)
+
+#define DP_PCON_DSC_MAX_SLICE_WIDTH 0x09B
+
+/* DP-HDMI2.1 PCON DSC Slice capabilities-2 */
+#define DP_PCON_DSC_SLICE_CAP_2 0x09C
+# define DP_PCON_DSC_16_PER_DSC_ENC (0x1 << 0)
+# define DP_PCON_DSC_20_PER_DSC_ENC (0x1 << 1)
+# define DP_PCON_DSC_24_PER_DSC_ENC (0x1 << 2)
+
+/* DP-HDMI2.1 PCON HDMI TX Encoder Bits/pixel increment */
+#define DP_PCON_DSC_BPP_INCR 0x09E
+# define DP_PCON_DSC_BPP_INCR_MASK (0x7 << 0)
+# define DP_PCON_DSC_ONE_16TH_BPP 0
+# define DP_PCON_DSC_ONE_8TH_BPP 1
+# define DP_PCON_DSC_ONE_4TH_BPP 2
+# define DP_PCON_DSC_ONE_HALF_BPP 3
+# define DP_PCON_DSC_ONE_BPP 4
+
/* DP Extended DSC Capabilities */
#define DP_DSC_BRANCH_OVERALL_THROUGHPUT_0 0x0a0 /* DP 1.4a SCR */
#define DP_DSC_BRANCH_OVERALL_THROUGHPUT_1 0x0a1
@@ -1124,6 +1202,12 @@ struct drm_device;
# define DP_HDMI_FORCE_SCRAMBLING (1 << 3) /* DP 1.4 */
#define DP_PROTOCOL_CONVERTER_CONTROL_2 0x3052 /* DP 1.3 */
# define DP_CONVERSION_TO_YCBCR422_ENABLE (1 << 0) /* DP 1.3 */
+# define DP_PCON_ENABLE_DSC_ENCODER (1 << 1)
+# define DP_PCON_ENCODER_PPS_OVERRIDE_MASK (0x3 << 2)
+# define DP_PCON_ENC_PPS_OVERRIDE_DISABLED 0
+# define DP_PCON_ENC_PPS_OVERRIDE_EN_PARAMS 1
+# define DP_PCON_ENC_PPS_OVERRIDE_EN_BUFFER 2
+
/* PCON Downstream HDMI ERROR Status per Lane */
#define DP_PCON_HDMI_ERROR_STATUS_LN0 0x3037
@@ -1135,6 +1219,29 @@ struct drm_device;
# define DP_PCON_HDMI_ERROR_COUNT_TEN_PLUS (1 << 1)
# define DP_PCON_HDMI_ERROR_COUNT_HUNDRED_PLUS (1 << 2)
+/* PCON HDMI CONFIG PPS Override Buffer
+ * Valid Offsets to be added to Base : 0-127
+ */
+#define DP_PCON_HDMI_PPS_OVERRIDE_BASE 0x3100
+
+/* PCON HDMI CONFIG PPS Override Parameter: Slice height
+ * Offset-0 8LSBs of the Slice height.
+ * Offset-1 8MSBs of the Slice height.
+ */
+#define DP_PCON_HDMI_PPS_OVRD_SLICE_HEIGHT 0x3180
+
+/* PCON HDMI CONFIG PPS Override Parameter: Slice width
+ * Offset-0 8LSBs of the Slice width.
+ * Offset-1 8MSBs of the Slice width.
+ */
+#define DP_PCON_HDMI_PPS_OVRD_SLICE_WIDTH 0x3182
+
+/* PCON HDMI CONFIG PPS Override Parameter: bits_per_pixel
+ * Offset-0 8LSBs of the bits_per_pixel.
+ * Offset-1 2MSBs of the bits_per_pixel.
+ */
+#define DP_PCON_HDMI_PPS_OVRD_BPP 0x3184
+
/* HDCP 1.3 and HDCP 2.2 */
#define DP_AUX_HDCP_BKSV 0x68000
#define DP_AUX_HDCP_RI_PRIME 0x68005
@@ -2053,5 +2160,12 @@ bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux);
int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8 *frl_trained_mask);
void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
struct drm_connector *connector);
+bool drm_dp_pcon_enc_is_dsc_1_2(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]);
+int drm_dp_pcon_dsc_max_slices(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]);
+int drm_dp_pcon_dsc_max_slice_width(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]);
+int drm_dp_pcon_dsc_bpp_incr(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE]);
+int drm_dp_pcon_pps_default(struct drm_dp_aux *aux);
+int drm_dp_pcon_pps_override_buf(struct drm_dp_aux *aux, u8 pps_buf[128]);
+int drm_dp_pcon_pps_override_param(struct drm_dp_aux *aux, u8 pps_param[6]);
#endif /* _DRM_DP_HELPER_H_ */
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 07/15] drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
DP Specification for DP2.0 to HDMI2.1 Pcon specifies support for conversion
of colorspace from RGB to YCbCr.
https://groups.vesa.org/wg/DP/document/previewpdf/15651
This patch adds the relavant registers and helper functions to
get the capability and set the color conversion bits for rgb->ycbcr
conversion through PCON.
v2: As suggested in review comments:
-Fixed bug in the check condition in a drm_helper as reported by
Dan Carpenter and Kernel test robot. (Dan Carepenter)
-Modified the color-conversion cap helper function, to accomodate
BT709 and BT2020 colorspace. (Uma Shankar)
-Added spec details for the new cap for color conversion. (Uma Shankar)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/drm_dp_helper.c | 61 +++++++++++++++++++++++++++++++++
include/drm/drm_dp_helper.h | 19 +++++++++-
2 files changed, 79 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c
index 689fd0d5f6c5..9abd65c694ab 100644
--- a/drivers/gpu/drm/drm_dp_helper.c
+++ b/drivers/gpu/drm/drm_dp_helper.c
@@ -949,6 +949,38 @@ bool drm_dp_downstream_444_to_420_conversion(const u8 dpcd[DP_RECEIVER_CAP_SIZE]
}
EXPORT_SYMBOL(drm_dp_downstream_444_to_420_conversion);
+/**
+ * drm_dp_downstream_rgb_to_ycbcr_conversion() - determine downstream facing port
+ * RGB->YCbCr conversion capability
+ * @dpcd: DisplayPort configuration data
+ * @port_cap: downstream facing port capabilities
+ * @colorspc: Colorspace for which conversion cap is sought
+ *
+ * Returns: whether the downstream facing port can convert RGB->YCbCr for a given
+ * colorspace.
+ */
+bool drm_dp_downstream_rgb_to_ycbcr_conversion(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
+ const u8 port_cap[4],
+ u8 color_spc)
+{
+ if (!drm_dp_is_branch(dpcd))
+ return false;
+
+ if (dpcd[DP_DPCD_REV] < 0x13)
+ return false;
+
+ switch (port_cap[0] & DP_DS_PORT_TYPE_MASK) {
+ case DP_DS_PORT_TYPE_HDMI:
+ if ((dpcd[DP_DOWNSTREAMPORT_PRESENT] & DP_DETAILED_CAP_INFO_AVAILABLE) == 0)
+ return false;
+
+ return port_cap[3] & color_spc;
+ default:
+ return false;
+ }
+}
+EXPORT_SYMBOL(drm_dp_downstream_rgb_to_ycbcr_conversion);
+
/**
* drm_dp_downstream_mode() - return a mode for downstream facing port
* @dev: DRM device
@@ -3101,3 +3133,32 @@ int drm_dp_pcon_pps_override_param(struct drm_dp_aux *aux, u8 pps_param[6])
return 0;
}
EXPORT_SYMBOL(drm_dp_pcon_pps_override_param);
+
+/*
+ * drm_dp_pcon_convert_rgb_to_ycbcr() - Configure the PCon to convert RGB to Ycbcr
+ * @aux: displayPort AUX channel
+ * @color_spc: Color-space/s for which conversion is to be enabled, 0 for disable.
+ *
+ * Returns 0 on success, else returns negative error code.
+ */
+int drm_dp_pcon_convert_rgb_to_ycbcr(struct drm_dp_aux *aux, u8 color_spc)
+{
+ int ret;
+ u8 buf;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PROTOCOL_CONVERTER_CONTROL_2, &buf);
+ if (ret < 0)
+ return ret;
+
+ if (color_spc & DP_CONVERSION_RGB_YCBCR_MASK)
+ buf |= (color_spc & DP_CONVERSION_RGB_YCBCR_MASK);
+ else
+ buf &= ~DP_CONVERSION_RGB_YCBCR_MASK;
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PROTOCOL_CONVERTER_CONTROL_2, buf);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_convert_rgb_to_ycbcr);
diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
index baad87fe6b0a..e096ee98842b 100644
--- a/include/drm/drm_dp_helper.h
+++ b/include/drm/drm_dp_helper.h
@@ -432,6 +432,17 @@ struct drm_device;
# define DP_DS_HDMI_YCBCR444_TO_422_CONV (1 << 3)
# define DP_DS_HDMI_YCBCR444_TO_420_CONV (1 << 4)
+/*
+ * VESA DP-to-HDMI PCON Specification adds caps for colorspace
+ * conversion in DFP cap DPCD 83h. Sec6.1 Table-3.
+ * Based on the available support the source can enable
+ * color conversion by writing into PROTOCOL_COVERTER_CONTROL_2
+ * DPCD 3052h.
+ */
+# define DP_DS_HDMI_BT601_RGB_YCBCR_CONV (1 << 5)
+# define DP_DS_HDMI_BT709_RGB_YCBCR_CONV (1 << 6)
+# define DP_DS_HDMI_BT2020_RGB_YCBCR_CONV (1 << 7)
+
#define DP_MAX_DOWNSTREAM_PORTS 0x10
/* DP Forward error Correction Registers */
@@ -1207,7 +1218,10 @@ struct drm_device;
# define DP_PCON_ENC_PPS_OVERRIDE_DISABLED 0
# define DP_PCON_ENC_PPS_OVERRIDE_EN_PARAMS 1
# define DP_PCON_ENC_PPS_OVERRIDE_EN_BUFFER 2
-
+# define DP_CONVERSION_RGB_YCBCR_MASK (7 << 4)
+# define DP_CONVERSION_BT601_RGB_YCBCR_ENABLE (1 << 4)
+# define DP_CONVERSION_BT709_RGB_YCBCR_ENABLE (1 << 5)
+# define DP_CONVERSION_BT2020_RGB_YCBCR_ENABLE (1 << 6)
/* PCON Downstream HDMI ERROR Status per Lane */
#define DP_PCON_HDMI_ERROR_STATUS_LN0 0x3037
@@ -2167,5 +2181,8 @@ int drm_dp_pcon_dsc_bpp_incr(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE
int drm_dp_pcon_pps_default(struct drm_dp_aux *aux);
int drm_dp_pcon_pps_override_buf(struct drm_dp_aux *aux, u8 pps_buf[128]);
int drm_dp_pcon_pps_override_param(struct drm_dp_aux *aux, u8 pps_param[6]);
+bool drm_dp_downstream_rgb_to_ycbcr_conversion(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
+ const u8 port_cap[4], u8 color_spc);
+int drm_dp_pcon_convert_rgb_to_ycbcr(struct drm_dp_aux *aux, u8 color_spc);
#endif /* _DRM_DP_HELPER_H_ */
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 07/15] drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
DP Specification for DP2.0 to HDMI2.1 Pcon specifies support for conversion
of colorspace from RGB to YCbCr.
https://groups.vesa.org/wg/DP/document/previewpdf/15651
This patch adds the relavant registers and helper functions to
get the capability and set the color conversion bits for rgb->ycbcr
conversion through PCON.
v2: As suggested in review comments:
-Fixed bug in the check condition in a drm_helper as reported by
Dan Carpenter and Kernel test robot. (Dan Carepenter)
-Modified the color-conversion cap helper function, to accomodate
BT709 and BT2020 colorspace. (Uma Shankar)
-Added spec details for the new cap for color conversion. (Uma Shankar)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/drm_dp_helper.c | 61 +++++++++++++++++++++++++++++++++
include/drm/drm_dp_helper.h | 19 +++++++++-
2 files changed, 79 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/drm_dp_helper.c b/drivers/gpu/drm/drm_dp_helper.c
index 689fd0d5f6c5..9abd65c694ab 100644
--- a/drivers/gpu/drm/drm_dp_helper.c
+++ b/drivers/gpu/drm/drm_dp_helper.c
@@ -949,6 +949,38 @@ bool drm_dp_downstream_444_to_420_conversion(const u8 dpcd[DP_RECEIVER_CAP_SIZE]
}
EXPORT_SYMBOL(drm_dp_downstream_444_to_420_conversion);
+/**
+ * drm_dp_downstream_rgb_to_ycbcr_conversion() - determine downstream facing port
+ * RGB->YCbCr conversion capability
+ * @dpcd: DisplayPort configuration data
+ * @port_cap: downstream facing port capabilities
+ * @colorspc: Colorspace for which conversion cap is sought
+ *
+ * Returns: whether the downstream facing port can convert RGB->YCbCr for a given
+ * colorspace.
+ */
+bool drm_dp_downstream_rgb_to_ycbcr_conversion(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
+ const u8 port_cap[4],
+ u8 color_spc)
+{
+ if (!drm_dp_is_branch(dpcd))
+ return false;
+
+ if (dpcd[DP_DPCD_REV] < 0x13)
+ return false;
+
+ switch (port_cap[0] & DP_DS_PORT_TYPE_MASK) {
+ case DP_DS_PORT_TYPE_HDMI:
+ if ((dpcd[DP_DOWNSTREAMPORT_PRESENT] & DP_DETAILED_CAP_INFO_AVAILABLE) == 0)
+ return false;
+
+ return port_cap[3] & color_spc;
+ default:
+ return false;
+ }
+}
+EXPORT_SYMBOL(drm_dp_downstream_rgb_to_ycbcr_conversion);
+
/**
* drm_dp_downstream_mode() - return a mode for downstream facing port
* @dev: DRM device
@@ -3101,3 +3133,32 @@ int drm_dp_pcon_pps_override_param(struct drm_dp_aux *aux, u8 pps_param[6])
return 0;
}
EXPORT_SYMBOL(drm_dp_pcon_pps_override_param);
+
+/*
+ * drm_dp_pcon_convert_rgb_to_ycbcr() - Configure the PCon to convert RGB to Ycbcr
+ * @aux: displayPort AUX channel
+ * @color_spc: Color-space/s for which conversion is to be enabled, 0 for disable.
+ *
+ * Returns 0 on success, else returns negative error code.
+ */
+int drm_dp_pcon_convert_rgb_to_ycbcr(struct drm_dp_aux *aux, u8 color_spc)
+{
+ int ret;
+ u8 buf;
+
+ ret = drm_dp_dpcd_readb(aux, DP_PROTOCOL_CONVERTER_CONTROL_2, &buf);
+ if (ret < 0)
+ return ret;
+
+ if (color_spc & DP_CONVERSION_RGB_YCBCR_MASK)
+ buf |= (color_spc & DP_CONVERSION_RGB_YCBCR_MASK);
+ else
+ buf &= ~DP_CONVERSION_RGB_YCBCR_MASK;
+
+ ret = drm_dp_dpcd_writeb(aux, DP_PROTOCOL_CONVERTER_CONTROL_2, buf);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_dp_pcon_convert_rgb_to_ycbcr);
diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
index baad87fe6b0a..e096ee98842b 100644
--- a/include/drm/drm_dp_helper.h
+++ b/include/drm/drm_dp_helper.h
@@ -432,6 +432,17 @@ struct drm_device;
# define DP_DS_HDMI_YCBCR444_TO_422_CONV (1 << 3)
# define DP_DS_HDMI_YCBCR444_TO_420_CONV (1 << 4)
+/*
+ * VESA DP-to-HDMI PCON Specification adds caps for colorspace
+ * conversion in DFP cap DPCD 83h. Sec6.1 Table-3.
+ * Based on the available support the source can enable
+ * color conversion by writing into PROTOCOL_COVERTER_CONTROL_2
+ * DPCD 3052h.
+ */
+# define DP_DS_HDMI_BT601_RGB_YCBCR_CONV (1 << 5)
+# define DP_DS_HDMI_BT709_RGB_YCBCR_CONV (1 << 6)
+# define DP_DS_HDMI_BT2020_RGB_YCBCR_CONV (1 << 7)
+
#define DP_MAX_DOWNSTREAM_PORTS 0x10
/* DP Forward error Correction Registers */
@@ -1207,7 +1218,10 @@ struct drm_device;
# define DP_PCON_ENC_PPS_OVERRIDE_DISABLED 0
# define DP_PCON_ENC_PPS_OVERRIDE_EN_PARAMS 1
# define DP_PCON_ENC_PPS_OVERRIDE_EN_BUFFER 2
-
+# define DP_CONVERSION_RGB_YCBCR_MASK (7 << 4)
+# define DP_CONVERSION_BT601_RGB_YCBCR_ENABLE (1 << 4)
+# define DP_CONVERSION_BT709_RGB_YCBCR_ENABLE (1 << 5)
+# define DP_CONVERSION_BT2020_RGB_YCBCR_ENABLE (1 << 6)
/* PCON Downstream HDMI ERROR Status per Lane */
#define DP_PCON_HDMI_ERROR_STATUS_LN0 0x3037
@@ -2167,5 +2181,8 @@ int drm_dp_pcon_dsc_bpp_incr(const u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE
int drm_dp_pcon_pps_default(struct drm_dp_aux *aux);
int drm_dp_pcon_pps_override_buf(struct drm_dp_aux *aux, u8 pps_buf[128]);
int drm_dp_pcon_pps_override_param(struct drm_dp_aux *aux, u8 pps_param[6]);
+bool drm_dp_downstream_rgb_to_ycbcr_conversion(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
+ const u8 port_cap[4], u8 color_spc);
+int drm_dp_pcon_convert_rgb_to_ycbcr(struct drm_dp_aux *aux, u8 color_spc);
#endif /* _DRM_DP_HELPER_H_ */
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 08/15] drm/i915: Capture max frl rate for PCON in dfp cap structure
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
HDMI2.1 PCON advertises Max FRL bandwidth supported by the PCON.
This patch captures this in dfp cap structure in intel_dp and uses
this to prune connector modes that cannot be supported by the PCON
and FRL bandwidth.
v2: Addressed review comments from Uma Shankar:
-tweaked the comparison of target bw and pcon frl bw to avoid roundup errors.
-minor modification of field names and comments.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
.../drm/i915/display/intel_display_types.h | 1 +
drivers/gpu/drm/i915/display/intel_dp.c | 30 +++++++++++++++++--
2 files changed, 29 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index 5bc5bfbc4551..c88d2b918d9f 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -1451,6 +1451,7 @@ struct intel_dp {
struct {
int min_tmds_clock, max_tmds_clock;
int max_dotclock;
+ int pcon_max_frl_bw;
u8 max_bpc;
bool ycbcr_444_to_420;
} dfp;
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index b2bc0c8c39c7..0596d6c24e73 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -716,6 +716,25 @@ intel_dp_mode_valid_downstream(struct intel_connector *connector,
const struct drm_display_info *info = &connector->base.display_info;
int tmds_clock;
+ /* If PCON supports FRL MODE, check FRL bandwidth constraints */
+ if (intel_dp->dfp.pcon_max_frl_bw) {
+ int target_bw;
+ int max_frl_bw;
+ int bpp = intel_dp_mode_min_output_bpp(&connector->base, mode);
+
+ target_bw = bpp * target_clock;
+
+ max_frl_bw = intel_dp->dfp.pcon_max_frl_bw;
+
+ /* converting bw from Gbps to Kbps*/
+ max_frl_bw = max_frl_bw * 1000000;
+
+ if (target_bw > max_frl_bw)
+ return MODE_CLOCK_HIGH;
+
+ return MODE_OK;
+ }
+
if (intel_dp->dfp.max_dotclock &&
target_clock > intel_dp->dfp.max_dotclock)
return MODE_CLOCK_HIGH;
@@ -6492,13 +6511,18 @@ intel_dp_update_dfp(struct intel_dp *intel_dp,
intel_dp->downstream_ports,
edid);
+ intel_dp->dfp.pcon_max_frl_bw =
+ drm_dp_get_pcon_max_frl_bw(intel_dp->dpcd,
+ intel_dp->downstream_ports);
+
drm_dbg_kms(&i915->drm,
- "[CONNECTOR:%d:%s] DFP max bpc %d, max dotclock %d, TMDS clock %d-%d\n",
+ "[CONNECTOR:%d:%s] DFP max bpc %d, max dotclock %d, TMDS clock %d-%d, PCON Max FRL BW %dGbps\n",
connector->base.base.id, connector->base.name,
intel_dp->dfp.max_bpc,
intel_dp->dfp.max_dotclock,
intel_dp->dfp.min_tmds_clock,
- intel_dp->dfp.max_tmds_clock);
+ intel_dp->dfp.max_tmds_clock,
+ intel_dp->dfp.pcon_max_frl_bw);
}
static void
@@ -6590,6 +6614,8 @@ intel_dp_unset_edid(struct intel_dp *intel_dp)
intel_dp->dfp.min_tmds_clock = 0;
intel_dp->dfp.max_tmds_clock = 0;
+ intel_dp->dfp.pcon_max_frl_bw = 0;
+
intel_dp->dfp.ycbcr_444_to_420 = false;
connector->base.ycbcr_420_allowed = false;
}
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 08/15] drm/i915: Capture max frl rate for PCON in dfp cap structure
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
HDMI2.1 PCON advertises Max FRL bandwidth supported by the PCON.
This patch captures this in dfp cap structure in intel_dp and uses
this to prune connector modes that cannot be supported by the PCON
and FRL bandwidth.
v2: Addressed review comments from Uma Shankar:
-tweaked the comparison of target bw and pcon frl bw to avoid roundup errors.
-minor modification of field names and comments.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
.../drm/i915/display/intel_display_types.h | 1 +
drivers/gpu/drm/i915/display/intel_dp.c | 30 +++++++++++++++++--
2 files changed, 29 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index 5bc5bfbc4551..c88d2b918d9f 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -1451,6 +1451,7 @@ struct intel_dp {
struct {
int min_tmds_clock, max_tmds_clock;
int max_dotclock;
+ int pcon_max_frl_bw;
u8 max_bpc;
bool ycbcr_444_to_420;
} dfp;
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index b2bc0c8c39c7..0596d6c24e73 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -716,6 +716,25 @@ intel_dp_mode_valid_downstream(struct intel_connector *connector,
const struct drm_display_info *info = &connector->base.display_info;
int tmds_clock;
+ /* If PCON supports FRL MODE, check FRL bandwidth constraints */
+ if (intel_dp->dfp.pcon_max_frl_bw) {
+ int target_bw;
+ int max_frl_bw;
+ int bpp = intel_dp_mode_min_output_bpp(&connector->base, mode);
+
+ target_bw = bpp * target_clock;
+
+ max_frl_bw = intel_dp->dfp.pcon_max_frl_bw;
+
+ /* converting bw from Gbps to Kbps*/
+ max_frl_bw = max_frl_bw * 1000000;
+
+ if (target_bw > max_frl_bw)
+ return MODE_CLOCK_HIGH;
+
+ return MODE_OK;
+ }
+
if (intel_dp->dfp.max_dotclock &&
target_clock > intel_dp->dfp.max_dotclock)
return MODE_CLOCK_HIGH;
@@ -6492,13 +6511,18 @@ intel_dp_update_dfp(struct intel_dp *intel_dp,
intel_dp->downstream_ports,
edid);
+ intel_dp->dfp.pcon_max_frl_bw =
+ drm_dp_get_pcon_max_frl_bw(intel_dp->dpcd,
+ intel_dp->downstream_ports);
+
drm_dbg_kms(&i915->drm,
- "[CONNECTOR:%d:%s] DFP max bpc %d, max dotclock %d, TMDS clock %d-%d\n",
+ "[CONNECTOR:%d:%s] DFP max bpc %d, max dotclock %d, TMDS clock %d-%d, PCON Max FRL BW %dGbps\n",
connector->base.base.id, connector->base.name,
intel_dp->dfp.max_bpc,
intel_dp->dfp.max_dotclock,
intel_dp->dfp.min_tmds_clock,
- intel_dp->dfp.max_tmds_clock);
+ intel_dp->dfp.max_tmds_clock,
+ intel_dp->dfp.pcon_max_frl_bw);
}
static void
@@ -6590,6 +6614,8 @@ intel_dp_unset_edid(struct intel_dp *intel_dp)
intel_dp->dfp.min_tmds_clock = 0;
intel_dp->dfp.max_tmds_clock = 0;
+ intel_dp->dfp.pcon_max_frl_bw = 0;
+
intel_dp->dfp.ycbcr_444_to_420 = false;
connector->base.ycbcr_420_allowed = false;
}
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
This patch adds functions to start FRL training for an HDMI2.1 sink,
connected via a PCON as a DP branch device.
This patch also adds a new structure for storing frl training related
data, when FRL training is completed.
v2: As suggested by Uma Shankar:
-renamed couple of variables for better clarity
-tweaked the macros used for correct semantics for true/false
-fixed other styling issues.
v3: Completed the TODO for condition for going to FRL mode.
Modified the condition to determine the required FRL b/w
based only on the Pcon and Sink's max FRL values.
Moved the frl structure initialization to intel_dp_init_connector().
v4: Fixed typo in initialization of frl structure.
v5: Always use FRL if its possible, instead of enabling only for
higher modes as done in v3.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
---
.../drm/i915/display/intel_display_types.h | 7 +
drivers/gpu/drm/i915/display/intel_dp.c | 151 ++++++++++++++++++
drivers/gpu/drm/i915/display/intel_dp.h | 2 +
3 files changed, 160 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index c88d2b918d9f..daecff9783ea 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -1339,6 +1339,11 @@ struct intel_dp_compliance {
u8 test_lane_count;
};
+struct intel_dp_pcon_frl {
+ bool is_trained;
+ int trained_rate_gbps;
+};
+
struct intel_dp {
i915_reg_t output_reg;
u32 DP;
@@ -1461,6 +1466,8 @@ struct intel_dp {
bool hobl_failed;
bool hobl_active;
+
+ struct intel_dp_pcon_frl frl;
};
enum lspcon_vendor {
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 0596d6c24e73..43027a6d5e5e 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -3891,6 +3891,8 @@ static void intel_disable_dp(struct intel_atomic_state *state,
intel_edp_backlight_off(old_conn_state);
intel_dp_set_power(intel_dp, DP_SET_POWER_D3);
intel_edp_panel_off(intel_dp);
+ intel_dp->frl.is_trained = false;
+ intel_dp->frl.trained_rate_gbps = 0;
}
static void g4x_disable_dp(struct intel_atomic_state *state,
@@ -3986,6 +3988,152 @@ cpt_set_link_train(struct intel_dp *intel_dp,
intel_de_posting_read(dev_priv, intel_dp->output_reg);
}
+static int intel_dp_pcon_get_frl_mask(u8 frl_bw_mask)
+{
+ int bw_gbps[] = {9, 18, 24, 32, 40, 48};
+ int i;
+
+ for (i = ARRAY_SIZE(bw_gbps) - 1; i >= 0; i--) {
+ if (frl_bw_mask & (1 << i))
+ return bw_gbps[i];
+ }
+ return 0;
+}
+
+static int intel_dp_pcon_set_frl_mask(int max_frl)
+{
+
+ switch (max_frl) {
+ case 48:
+ return DP_PCON_FRL_BW_MASK_48GBPS;
+ case 40:
+ return DP_PCON_FRL_BW_MASK_40GBPS;
+ case 32:
+ return DP_PCON_FRL_BW_MASK_32GBPS;
+ case 24:
+ return DP_PCON_FRL_BW_MASK_24GBPS;
+ case 18:
+ return DP_PCON_FRL_BW_MASK_18GBPS;
+ case 9:
+ return DP_PCON_FRL_BW_MASK_9GBPS;
+ }
+
+ return 0;
+}
+
+static int intel_dp_hdmi_sink_max_frl(struct intel_dp *intel_dp)
+{
+ struct intel_connector *intel_connector = intel_dp->attached_connector;
+ struct drm_connector *connector = &intel_connector->base;
+
+ return (connector->display_info.hdmi.max_frl_rate_per_lane *
+ connector->display_info.hdmi.max_lanes);
+}
+
+static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
+{
+#define PCON_EXTENDED_TRAIN_MODE (1 > 0)
+#define PCON_CONCURRENT_MODE (1 > 0)
+#define PCON_SEQUENTIAL_MODE !PCON_CONCURRENT_MODE
+#define PCON_NORMAL_TRAIN_MODE !PCON_EXTENDED_TRAIN_MODE
+#define TIMEOUT_FRL_READY_MS 500
+#define TIMEOUT_HDMI_LINK_ACTIVE_MS 1000
+
+ struct drm_i915_private *i915 = dp_to_i915(intel_dp);
+ int max_frl_bw, max_pcon_frl_bw, max_edid_frl_bw, ret;
+ u8 max_frl_bw_mask = 0, frl_trained_mask;
+ bool is_active;
+
+ ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
+ if (ret < 0)
+ return ret;
+
+ max_pcon_frl_bw = intel_dp->dfp.pcon_max_frl_bw;
+ drm_dbg(&i915->drm, "PCON max rate = %d Gbps\n", max_pcon_frl_bw);
+
+ max_edid_frl_bw = intel_dp_hdmi_sink_max_frl(intel_dp);
+ drm_dbg(&i915->drm, "Sink max rate from EDID = %d Gbps\n", max_edid_frl_bw);
+
+ max_frl_bw = min(max_edid_frl_bw, max_pcon_frl_bw);
+
+ if (max_frl_bw <= 0)
+ return -EINVAL;
+
+ ret = drm_dp_pcon_frl_prepare(&intel_dp->aux, false);
+ if (ret < 0)
+ return ret;
+ /* Wait for PCON to be FRL Ready */
+ wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) == true, TIMEOUT_FRL_READY_MS);
+
+ if (!is_active)
+ return -ETIMEDOUT;
+
+ max_frl_bw_mask = intel_dp_pcon_set_frl_mask(max_frl_bw);
+ ret = drm_dp_pcon_frl_configure_1(&intel_dp->aux, max_frl_bw, PCON_SEQUENTIAL_MODE);
+ if (ret < 0)
+ return ret;
+ ret = drm_dp_pcon_frl_configure_2(&intel_dp->aux, max_frl_bw_mask, PCON_NORMAL_TRAIN_MODE);
+ if (ret < 0)
+ return ret;
+ ret = drm_dp_pcon_frl_enable(&intel_dp->aux);
+ if (ret < 0)
+ return ret;
+ /*
+ * Wait for FRL to be completed
+ * Check if the HDMI Link is up and active.
+ */
+ wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux) == true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
+
+ if (!is_active)
+ return -ETIMEDOUT;
+
+ /* Verify HDMI Link configuration shows FRL Mode */
+ if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
+ drm_dbg(&i915->drm, "HDMI couldn't be trained in FRL Mode\n");
+ return -EINVAL;
+ }
+ drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK = %u\n", max_frl_bw_mask, frl_trained_mask);
+
+ intel_dp->frl.trained_rate_gbps = intel_dp_pcon_get_frl_mask(frl_trained_mask);
+ intel_dp->frl.is_trained = true;
+ drm_dbg(&i915->drm, "FRL trained with : %d Gbps\n", intel_dp->frl.trained_rate_gbps);
+
+ return 0;
+}
+
+static bool intel_dp_is_hdmi_2_1_sink(struct intel_dp *intel_dp)
+{
+ if (drm_dp_is_branch(intel_dp->dpcd) &&
+ intel_dp->has_hdmi_sink &&
+ intel_dp_hdmi_sink_max_frl(intel_dp) > 0)
+ return true;
+
+ return false;
+}
+
+void intel_dp_check_frl_training(struct intel_dp *intel_dp)
+{
+ struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
+
+ /* Always go for FRL training if supported */
+ if (!intel_dp_is_hdmi_2_1_sink(intel_dp) ||
+ intel_dp->frl.is_trained)
+ return;
+
+ if (intel_dp_pcon_start_frl_training(intel_dp) < 0) {
+ int ret, mode;
+
+ drm_dbg(&dev_priv->drm, "Couldnt set FRL mode, continuing with TMDS mode\n");
+ ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
+ mode = drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, NULL);
+
+ if (ret < 0 || mode != DP_PCON_HDMI_MODE_TMDS)
+ drm_dbg(&dev_priv->drm, "Issue with PCON, cannot set TMDS mode\n");
+ } else {
+ drm_dbg(&dev_priv->drm, "FRL training Completed\n");
+ }
+}
+
static void
g4x_set_link_train(struct intel_dp *intel_dp,
const struct intel_crtc_state *crtc_state,
@@ -8210,6 +8358,9 @@ intel_dp_init_connector(struct intel_digital_port *dig_port,
(temp & ~0xf) | 0xd);
}
+ intel_dp->frl.is_trained = false;
+ intel_dp->frl.trained_rate_gbps = 0;
+
return true;
fail:
diff --git a/drivers/gpu/drm/i915/display/intel_dp.h b/drivers/gpu/drm/i915/display/intel_dp.h
index b871a09b6901..58b76a20459c 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.h
+++ b/drivers/gpu/drm/i915/display/intel_dp.h
@@ -144,4 +144,6 @@ bool intel_dp_initial_fastset_check(struct intel_encoder *encoder,
void intel_dp_sync_state(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state);
+void intel_dp_check_frl_training(struct intel_dp *intel_dp);
+
#endif /* __INTEL_DP_H__ */
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
This patch adds functions to start FRL training for an HDMI2.1 sink,
connected via a PCON as a DP branch device.
This patch also adds a new structure for storing frl training related
data, when FRL training is completed.
v2: As suggested by Uma Shankar:
-renamed couple of variables for better clarity
-tweaked the macros used for correct semantics for true/false
-fixed other styling issues.
v3: Completed the TODO for condition for going to FRL mode.
Modified the condition to determine the required FRL b/w
based only on the Pcon and Sink's max FRL values.
Moved the frl structure initialization to intel_dp_init_connector().
v4: Fixed typo in initialization of frl structure.
v5: Always use FRL if its possible, instead of enabling only for
higher modes as done in v3.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
---
.../drm/i915/display/intel_display_types.h | 7 +
drivers/gpu/drm/i915/display/intel_dp.c | 151 ++++++++++++++++++
drivers/gpu/drm/i915/display/intel_dp.h | 2 +
3 files changed, 160 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index c88d2b918d9f..daecff9783ea 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -1339,6 +1339,11 @@ struct intel_dp_compliance {
u8 test_lane_count;
};
+struct intel_dp_pcon_frl {
+ bool is_trained;
+ int trained_rate_gbps;
+};
+
struct intel_dp {
i915_reg_t output_reg;
u32 DP;
@@ -1461,6 +1466,8 @@ struct intel_dp {
bool hobl_failed;
bool hobl_active;
+
+ struct intel_dp_pcon_frl frl;
};
enum lspcon_vendor {
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 0596d6c24e73..43027a6d5e5e 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -3891,6 +3891,8 @@ static void intel_disable_dp(struct intel_atomic_state *state,
intel_edp_backlight_off(old_conn_state);
intel_dp_set_power(intel_dp, DP_SET_POWER_D3);
intel_edp_panel_off(intel_dp);
+ intel_dp->frl.is_trained = false;
+ intel_dp->frl.trained_rate_gbps = 0;
}
static void g4x_disable_dp(struct intel_atomic_state *state,
@@ -3986,6 +3988,152 @@ cpt_set_link_train(struct intel_dp *intel_dp,
intel_de_posting_read(dev_priv, intel_dp->output_reg);
}
+static int intel_dp_pcon_get_frl_mask(u8 frl_bw_mask)
+{
+ int bw_gbps[] = {9, 18, 24, 32, 40, 48};
+ int i;
+
+ for (i = ARRAY_SIZE(bw_gbps) - 1; i >= 0; i--) {
+ if (frl_bw_mask & (1 << i))
+ return bw_gbps[i];
+ }
+ return 0;
+}
+
+static int intel_dp_pcon_set_frl_mask(int max_frl)
+{
+
+ switch (max_frl) {
+ case 48:
+ return DP_PCON_FRL_BW_MASK_48GBPS;
+ case 40:
+ return DP_PCON_FRL_BW_MASK_40GBPS;
+ case 32:
+ return DP_PCON_FRL_BW_MASK_32GBPS;
+ case 24:
+ return DP_PCON_FRL_BW_MASK_24GBPS;
+ case 18:
+ return DP_PCON_FRL_BW_MASK_18GBPS;
+ case 9:
+ return DP_PCON_FRL_BW_MASK_9GBPS;
+ }
+
+ return 0;
+}
+
+static int intel_dp_hdmi_sink_max_frl(struct intel_dp *intel_dp)
+{
+ struct intel_connector *intel_connector = intel_dp->attached_connector;
+ struct drm_connector *connector = &intel_connector->base;
+
+ return (connector->display_info.hdmi.max_frl_rate_per_lane *
+ connector->display_info.hdmi.max_lanes);
+}
+
+static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
+{
+#define PCON_EXTENDED_TRAIN_MODE (1 > 0)
+#define PCON_CONCURRENT_MODE (1 > 0)
+#define PCON_SEQUENTIAL_MODE !PCON_CONCURRENT_MODE
+#define PCON_NORMAL_TRAIN_MODE !PCON_EXTENDED_TRAIN_MODE
+#define TIMEOUT_FRL_READY_MS 500
+#define TIMEOUT_HDMI_LINK_ACTIVE_MS 1000
+
+ struct drm_i915_private *i915 = dp_to_i915(intel_dp);
+ int max_frl_bw, max_pcon_frl_bw, max_edid_frl_bw, ret;
+ u8 max_frl_bw_mask = 0, frl_trained_mask;
+ bool is_active;
+
+ ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
+ if (ret < 0)
+ return ret;
+
+ max_pcon_frl_bw = intel_dp->dfp.pcon_max_frl_bw;
+ drm_dbg(&i915->drm, "PCON max rate = %d Gbps\n", max_pcon_frl_bw);
+
+ max_edid_frl_bw = intel_dp_hdmi_sink_max_frl(intel_dp);
+ drm_dbg(&i915->drm, "Sink max rate from EDID = %d Gbps\n", max_edid_frl_bw);
+
+ max_frl_bw = min(max_edid_frl_bw, max_pcon_frl_bw);
+
+ if (max_frl_bw <= 0)
+ return -EINVAL;
+
+ ret = drm_dp_pcon_frl_prepare(&intel_dp->aux, false);
+ if (ret < 0)
+ return ret;
+ /* Wait for PCON to be FRL Ready */
+ wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) == true, TIMEOUT_FRL_READY_MS);
+
+ if (!is_active)
+ return -ETIMEDOUT;
+
+ max_frl_bw_mask = intel_dp_pcon_set_frl_mask(max_frl_bw);
+ ret = drm_dp_pcon_frl_configure_1(&intel_dp->aux, max_frl_bw, PCON_SEQUENTIAL_MODE);
+ if (ret < 0)
+ return ret;
+ ret = drm_dp_pcon_frl_configure_2(&intel_dp->aux, max_frl_bw_mask, PCON_NORMAL_TRAIN_MODE);
+ if (ret < 0)
+ return ret;
+ ret = drm_dp_pcon_frl_enable(&intel_dp->aux);
+ if (ret < 0)
+ return ret;
+ /*
+ * Wait for FRL to be completed
+ * Check if the HDMI Link is up and active.
+ */
+ wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux) == true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
+
+ if (!is_active)
+ return -ETIMEDOUT;
+
+ /* Verify HDMI Link configuration shows FRL Mode */
+ if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
+ drm_dbg(&i915->drm, "HDMI couldn't be trained in FRL Mode\n");
+ return -EINVAL;
+ }
+ drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK = %u\n", max_frl_bw_mask, frl_trained_mask);
+
+ intel_dp->frl.trained_rate_gbps = intel_dp_pcon_get_frl_mask(frl_trained_mask);
+ intel_dp->frl.is_trained = true;
+ drm_dbg(&i915->drm, "FRL trained with : %d Gbps\n", intel_dp->frl.trained_rate_gbps);
+
+ return 0;
+}
+
+static bool intel_dp_is_hdmi_2_1_sink(struct intel_dp *intel_dp)
+{
+ if (drm_dp_is_branch(intel_dp->dpcd) &&
+ intel_dp->has_hdmi_sink &&
+ intel_dp_hdmi_sink_max_frl(intel_dp) > 0)
+ return true;
+
+ return false;
+}
+
+void intel_dp_check_frl_training(struct intel_dp *intel_dp)
+{
+ struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
+
+ /* Always go for FRL training if supported */
+ if (!intel_dp_is_hdmi_2_1_sink(intel_dp) ||
+ intel_dp->frl.is_trained)
+ return;
+
+ if (intel_dp_pcon_start_frl_training(intel_dp) < 0) {
+ int ret, mode;
+
+ drm_dbg(&dev_priv->drm, "Couldnt set FRL mode, continuing with TMDS mode\n");
+ ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
+ mode = drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, NULL);
+
+ if (ret < 0 || mode != DP_PCON_HDMI_MODE_TMDS)
+ drm_dbg(&dev_priv->drm, "Issue with PCON, cannot set TMDS mode\n");
+ } else {
+ drm_dbg(&dev_priv->drm, "FRL training Completed\n");
+ }
+}
+
static void
g4x_set_link_train(struct intel_dp *intel_dp,
const struct intel_crtc_state *crtc_state,
@@ -8210,6 +8358,9 @@ intel_dp_init_connector(struct intel_digital_port *dig_port,
(temp & ~0xf) | 0xd);
}
+ intel_dp->frl.is_trained = false;
+ intel_dp->frl.trained_rate_gbps = 0;
+
return true;
fail:
diff --git a/drivers/gpu/drm/i915/display/intel_dp.h b/drivers/gpu/drm/i915/display/intel_dp.h
index b871a09b6901..58b76a20459c 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.h
+++ b/drivers/gpu/drm/i915/display/intel_dp.h
@@ -144,4 +144,6 @@ bool intel_dp_initial_fastset_check(struct intel_encoder *encoder,
void intel_dp_sync_state(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state);
+void intel_dp_check_frl_training(struct intel_dp *intel_dp);
+
#endif /* __INTEL_DP_H__ */
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 10/15] drm/i915: Check for FRL training before DP Link training
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
This patch calls functions to check FRL training requirements
for an HDMI2.1 sink, when connected through PCON.
The call is made before the DP link training. In case FRL is not
required or failure during FRL training, the TMDS mode is selected
for the pcon.
v2: moved check_frl_training() just after FEC READY, before
starting DP link training.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/i915/display/intel_ddi.c | 2 ++
drivers/gpu/drm/i915/display/intel_dp.c | 2 ++
2 files changed, 4 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index 6863236df1d0..974cf42351bc 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -3652,6 +3652,8 @@ static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
*/
intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
+ intel_dp_check_frl_training(intel_dp);
+
/*
* 7.i Follow DisplayPort specification training sequence (see notes for
* failure handling)
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 43027a6d5e5e..1e0ff39bb927 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -4264,6 +4264,7 @@ static void intel_enable_dp(struct intel_atomic_state *state,
intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
intel_dp_configure_protocol_converter(intel_dp);
+ intel_dp_check_frl_training(intel_dp);
intel_dp_start_link_train(intel_dp, pipe_config);
intel_dp_stop_link_train(intel_dp, pipe_config);
@@ -6185,6 +6186,7 @@ int intel_dp_retrain_link(struct intel_encoder *encoder,
!intel_dp_mst_is_master_trans(crtc_state))
continue;
+ intel_dp_check_frl_training(intel_dp);
intel_dp_start_link_train(intel_dp, crtc_state);
intel_dp_stop_link_train(intel_dp, crtc_state);
break;
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 10/15] drm/i915: Check for FRL training before DP Link training
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
This patch calls functions to check FRL training requirements
for an HDMI2.1 sink, when connected through PCON.
The call is made before the DP link training. In case FRL is not
required or failure during FRL training, the TMDS mode is selected
for the pcon.
v2: moved check_frl_training() just after FEC READY, before
starting DP link training.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/i915/display/intel_ddi.c | 2 ++
drivers/gpu/drm/i915/display/intel_dp.c | 2 ++
2 files changed, 4 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index 6863236df1d0..974cf42351bc 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -3652,6 +3652,8 @@ static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
*/
intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
+ intel_dp_check_frl_training(intel_dp);
+
/*
* 7.i Follow DisplayPort specification training sequence (see notes for
* failure handling)
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 43027a6d5e5e..1e0ff39bb927 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -4264,6 +4264,7 @@ static void intel_enable_dp(struct intel_atomic_state *state,
intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
intel_dp_configure_protocol_converter(intel_dp);
+ intel_dp_check_frl_training(intel_dp);
intel_dp_start_link_train(intel_dp, pipe_config);
intel_dp_stop_link_train(intel_dp, pipe_config);
@@ -6185,6 +6186,7 @@ int intel_dp_retrain_link(struct intel_encoder *encoder,
!intel_dp_mst_is_master_trans(crtc_state))
continue;
+ intel_dp_check_frl_training(intel_dp);
intel_dp_start_link_train(intel_dp, crtc_state);
intel_dp_stop_link_train(intel_dp, crtc_state);
break;
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 11/15] drm/i915: Add support for enabling link status and recovery
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
From: Swati Sharma <swati2.sharma@intel.com>
In this patch enables support for detecting link failures between
PCON and HDMI sink in i915 driver. HDMI link loss indication to
upstream DP source is indicated via IRQ_HPD. This is followed by
reading of HDMI link configuration status (HDMI_TX_LINK_ACTIVE_STATUS).
If the PCON → HDMI 2.1 link status is off; reinitiate frl link
training to recover. Also, report HDMI FRL link error count range for
each individual FRL active lane is indicated by
DOWNSTREAM_HDMI_ERROR_STATUS_LN registers.
v2: Checked for dpcd read and write failures and added debug message.
(Uma Shankar)
v3: Rearranged code to re-start FRL link training or fall back to
TMDS mode.
v4: Resused function to check frl which inturn restarts FRL and
fallback to TMDS mode.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
---
drivers/gpu/drm/i915/display/intel_dp.c | 53 +++++++++++++++++++++++--
1 file changed, 50 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 1e0ff39bb927..66f35e7c9903 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -6013,6 +6013,28 @@ intel_dp_check_mst_status(struct intel_dp *intel_dp)
return link_ok;
}
+static void
+intel_dp_handle_hdmi_link_status_change(struct intel_dp *intel_dp)
+{
+ bool is_active;
+ u8 buf = 0;
+
+ is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux);
+ if (intel_dp->frl.is_trained && !is_active) {
+ if (drm_dp_dpcd_readb(&intel_dp->aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf) < 0)
+ return;
+
+ buf &= ~DP_PCON_ENABLE_HDMI_LINK;
+ if (drm_dp_dpcd_writeb(&intel_dp->aux, DP_PCON_HDMI_LINK_CONFIG_1, buf) < 0)
+ return;
+
+ drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux, &intel_dp->attached_connector->base);
+
+ /* Restart FRL training or fall back to TMDS mode */
+ intel_dp_check_frl_training(intel_dp);
+ }
+}
+
static bool
intel_dp_needs_link_retrain(struct intel_dp *intel_dp)
{
@@ -6378,7 +6400,7 @@ intel_dp_hotplug(struct intel_encoder *encoder,
return state;
}
-static void intel_dp_check_service_irq(struct intel_dp *intel_dp)
+static void intel_dp_check_device_service_irq(struct intel_dp *intel_dp)
{
struct drm_i915_private *i915 = dp_to_i915(intel_dp);
u8 val;
@@ -6402,6 +6424,30 @@ static void intel_dp_check_service_irq(struct intel_dp *intel_dp)
drm_dbg_kms(&i915->drm, "Sink specific irq unhandled\n");
}
+static void intel_dp_check_link_service_irq(struct intel_dp *intel_dp)
+{
+ struct drm_i915_private *i915 = dp_to_i915(intel_dp);
+ u8 val;
+
+ if (intel_dp->dpcd[DP_DPCD_REV] < 0x11)
+ return;
+
+ if (drm_dp_dpcd_readb(&intel_dp->aux,
+ DP_LINK_SERVICE_IRQ_VECTOR_ESI0, &val) != 1 || !val) {
+ drm_dbg_kms(&i915->drm, "Error in reading link service irq vector\n");
+ return;
+ }
+
+ if (drm_dp_dpcd_writeb(&intel_dp->aux,
+ DP_LINK_SERVICE_IRQ_VECTOR_ESI0, val) != 1) {
+ drm_dbg_kms(&i915->drm, "Error in writing link service irq vector\n");
+ return;
+ }
+
+ if (val & HDMI_LINK_STATUS_CHANGED)
+ intel_dp_handle_hdmi_link_status_change(intel_dp);
+}
+
/*
* According to DP spec
* 5.1.2:
@@ -6441,7 +6487,8 @@ intel_dp_short_pulse(struct intel_dp *intel_dp)
return false;
}
- intel_dp_check_service_irq(intel_dp);
+ intel_dp_check_device_service_irq(intel_dp);
+ intel_dp_check_link_service_irq(intel_dp);
/* Handle CEC interrupts, if any */
drm_dp_cec_irq(&intel_dp->aux);
@@ -6871,7 +6918,7 @@ intel_dp_detect(struct drm_connector *connector,
to_intel_connector(connector)->detect_edid)
status = connector_status_connected;
- intel_dp_check_service_irq(intel_dp);
+ intel_dp_check_device_service_irq(intel_dp);
out:
if (status != connector_status_connected && !intel_dp->is_mst)
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 11/15] drm/i915: Add support for enabling link status and recovery
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
From: Swati Sharma <swati2.sharma@intel.com>
In this patch enables support for detecting link failures between
PCON and HDMI sink in i915 driver. HDMI link loss indication to
upstream DP source is indicated via IRQ_HPD. This is followed by
reading of HDMI link configuration status (HDMI_TX_LINK_ACTIVE_STATUS).
If the PCON → HDMI 2.1 link status is off; reinitiate frl link
training to recover. Also, report HDMI FRL link error count range for
each individual FRL active lane is indicated by
DOWNSTREAM_HDMI_ERROR_STATUS_LN registers.
v2: Checked for dpcd read and write failures and added debug message.
(Uma Shankar)
v3: Rearranged code to re-start FRL link training or fall back to
TMDS mode.
v4: Resused function to check frl which inturn restarts FRL and
fallback to TMDS mode.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
---
drivers/gpu/drm/i915/display/intel_dp.c | 53 +++++++++++++++++++++++--
1 file changed, 50 insertions(+), 3 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 1e0ff39bb927..66f35e7c9903 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -6013,6 +6013,28 @@ intel_dp_check_mst_status(struct intel_dp *intel_dp)
return link_ok;
}
+static void
+intel_dp_handle_hdmi_link_status_change(struct intel_dp *intel_dp)
+{
+ bool is_active;
+ u8 buf = 0;
+
+ is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux);
+ if (intel_dp->frl.is_trained && !is_active) {
+ if (drm_dp_dpcd_readb(&intel_dp->aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf) < 0)
+ return;
+
+ buf &= ~DP_PCON_ENABLE_HDMI_LINK;
+ if (drm_dp_dpcd_writeb(&intel_dp->aux, DP_PCON_HDMI_LINK_CONFIG_1, buf) < 0)
+ return;
+
+ drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux, &intel_dp->attached_connector->base);
+
+ /* Restart FRL training or fall back to TMDS mode */
+ intel_dp_check_frl_training(intel_dp);
+ }
+}
+
static bool
intel_dp_needs_link_retrain(struct intel_dp *intel_dp)
{
@@ -6378,7 +6400,7 @@ intel_dp_hotplug(struct intel_encoder *encoder,
return state;
}
-static void intel_dp_check_service_irq(struct intel_dp *intel_dp)
+static void intel_dp_check_device_service_irq(struct intel_dp *intel_dp)
{
struct drm_i915_private *i915 = dp_to_i915(intel_dp);
u8 val;
@@ -6402,6 +6424,30 @@ static void intel_dp_check_service_irq(struct intel_dp *intel_dp)
drm_dbg_kms(&i915->drm, "Sink specific irq unhandled\n");
}
+static void intel_dp_check_link_service_irq(struct intel_dp *intel_dp)
+{
+ struct drm_i915_private *i915 = dp_to_i915(intel_dp);
+ u8 val;
+
+ if (intel_dp->dpcd[DP_DPCD_REV] < 0x11)
+ return;
+
+ if (drm_dp_dpcd_readb(&intel_dp->aux,
+ DP_LINK_SERVICE_IRQ_VECTOR_ESI0, &val) != 1 || !val) {
+ drm_dbg_kms(&i915->drm, "Error in reading link service irq vector\n");
+ return;
+ }
+
+ if (drm_dp_dpcd_writeb(&intel_dp->aux,
+ DP_LINK_SERVICE_IRQ_VECTOR_ESI0, val) != 1) {
+ drm_dbg_kms(&i915->drm, "Error in writing link service irq vector\n");
+ return;
+ }
+
+ if (val & HDMI_LINK_STATUS_CHANGED)
+ intel_dp_handle_hdmi_link_status_change(intel_dp);
+}
+
/*
* According to DP spec
* 5.1.2:
@@ -6441,7 +6487,8 @@ intel_dp_short_pulse(struct intel_dp *intel_dp)
return false;
}
- intel_dp_check_service_irq(intel_dp);
+ intel_dp_check_device_service_irq(intel_dp);
+ intel_dp_check_link_service_irq(intel_dp);
/* Handle CEC interrupts, if any */
drm_dp_cec_irq(&intel_dp->aux);
@@ -6871,7 +6918,7 @@ intel_dp_detect(struct drm_connector *connector,
to_intel_connector(connector)->detect_edid)
status = connector_status_connected;
- intel_dp_check_service_irq(intel_dp);
+ intel_dp_check_device_service_irq(intel_dp);
out:
if (status != connector_status_connected && !intel_dp->is_mst)
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 12/15] drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
This patch adds support to read and store the DSC capabilities of the
HDMI2.1 PCon encoder. It also adds a new field to store these caps,
The caps are read during dfp update and can later be used to get the
PPS parameters for PCON-HDMI2.1 sink pair. Which inturn will be used
to take a call to override the existing PPS-metadata, by either
writing the entire new PPS metadata, or by writing only the
PPS override parameters.
v2: Restructured the code to read all capability DPCDs at once and store
in an array in intel_dp structure.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
.../drm/i915/display/intel_display_types.h | 1 +
drivers/gpu/drm/i915/display/intel_dp.c | 20 +++++++++++++++++++
2 files changed, 21 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index daecff9783ea..4c01c7c23dfd 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -1362,6 +1362,7 @@ struct intel_dp {
u8 lttpr_common_caps[DP_LTTPR_COMMON_CAP_SIZE];
u8 lttpr_phy_caps[DP_MAX_LTTPR_COUNT][DP_LTTPR_PHY_CAP_SIZE];
u8 fec_capable;
+ u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE];
/* source rates */
int num_source_rates;
const int *source_rates;
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 66f35e7c9903..7e2c334b3a17 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -3988,6 +3988,24 @@ cpt_set_link_train(struct intel_dp *intel_dp,
intel_de_posting_read(dev_priv, intel_dp->output_reg);
}
+static void intel_dp_get_pcon_dsc_cap(struct intel_dp *intel_dp)
+{
+ struct drm_i915_private *i915 = dp_to_i915(intel_dp);
+
+ /* Clear the cached register set to avoid using stale values */
+
+ memset(intel_dp->pcon_dsc_dpcd, 0, sizeof(intel_dp->pcon_dsc_dpcd));
+
+ if (drm_dp_dpcd_read(&intel_dp->aux, DP_PCON_DSC_ENCODER,
+ intel_dp->pcon_dsc_dpcd,
+ sizeof(intel_dp->pcon_dsc_dpcd)) < 0)
+ drm_err(&i915->drm, "Failed to read DPCD register 0x%x\n",
+ DP_PCON_DSC_ENCODER);
+
+ drm_dbg_kms(&i915->drm, "PCON ENCODER DSC DPCD: %*ph\n",
+ (int)sizeof(intel_dp->pcon_dsc_dpcd), intel_dp->pcon_dsc_dpcd);
+}
+
static int intel_dp_pcon_get_frl_mask(u8 frl_bw_mask)
{
int bw_gbps[] = {9, 18, 24, 32, 40, 48};
@@ -6720,6 +6738,8 @@ intel_dp_update_dfp(struct intel_dp *intel_dp,
intel_dp->dfp.min_tmds_clock,
intel_dp->dfp.max_tmds_clock,
intel_dp->dfp.pcon_max_frl_bw);
+
+ intel_dp_get_pcon_dsc_cap(intel_dp);
}
static void
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 12/15] drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
This patch adds support to read and store the DSC capabilities of the
HDMI2.1 PCon encoder. It also adds a new field to store these caps,
The caps are read during dfp update and can later be used to get the
PPS parameters for PCON-HDMI2.1 sink pair. Which inturn will be used
to take a call to override the existing PPS-metadata, by either
writing the entire new PPS metadata, or by writing only the
PPS override parameters.
v2: Restructured the code to read all capability DPCDs at once and store
in an array in intel_dp structure.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
.../drm/i915/display/intel_display_types.h | 1 +
drivers/gpu/drm/i915/display/intel_dp.c | 20 +++++++++++++++++++
2 files changed, 21 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index daecff9783ea..4c01c7c23dfd 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -1362,6 +1362,7 @@ struct intel_dp {
u8 lttpr_common_caps[DP_LTTPR_COMMON_CAP_SIZE];
u8 lttpr_phy_caps[DP_MAX_LTTPR_COUNT][DP_LTTPR_PHY_CAP_SIZE];
u8 fec_capable;
+ u8 pcon_dsc_dpcd[DP_PCON_DSC_ENCODER_CAP_SIZE];
/* source rates */
int num_source_rates;
const int *source_rates;
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 66f35e7c9903..7e2c334b3a17 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -3988,6 +3988,24 @@ cpt_set_link_train(struct intel_dp *intel_dp,
intel_de_posting_read(dev_priv, intel_dp->output_reg);
}
+static void intel_dp_get_pcon_dsc_cap(struct intel_dp *intel_dp)
+{
+ struct drm_i915_private *i915 = dp_to_i915(intel_dp);
+
+ /* Clear the cached register set to avoid using stale values */
+
+ memset(intel_dp->pcon_dsc_dpcd, 0, sizeof(intel_dp->pcon_dsc_dpcd));
+
+ if (drm_dp_dpcd_read(&intel_dp->aux, DP_PCON_DSC_ENCODER,
+ intel_dp->pcon_dsc_dpcd,
+ sizeof(intel_dp->pcon_dsc_dpcd)) < 0)
+ drm_err(&i915->drm, "Failed to read DPCD register 0x%x\n",
+ DP_PCON_DSC_ENCODER);
+
+ drm_dbg_kms(&i915->drm, "PCON ENCODER DSC DPCD: %*ph\n",
+ (int)sizeof(intel_dp->pcon_dsc_dpcd), intel_dp->pcon_dsc_dpcd);
+}
+
static int intel_dp_pcon_get_frl_mask(u8 frl_bw_mask)
{
int bw_gbps[] = {9, 18, 24, 32, 40, 48};
@@ -6720,6 +6738,8 @@ intel_dp_update_dfp(struct intel_dp *intel_dp,
intel_dp->dfp.min_tmds_clock,
intel_dp->dfp.max_tmds_clock,
intel_dp->dfp.pcon_max_frl_bw);
+
+ intel_dp_get_pcon_dsc_cap(intel_dp);
}
static void
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 13/15] drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
The DP-HDMI2.1 PCON spec provides way for a source to set PPS
parameters: slice height, slice width and bits_per_pixel, based on
the HDMI2.1 sink capabilities. The DSC encoder of the PCON will
respect these parameters, while preparing the 128 byte PPS.
This patch adds helper functions to calculate these PPS paremeters as
per the HDMI2.1 specification.
v2: Addressed review comments given by Uma Shankar:
-added documentation for functions
-fixed typos and errors
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/i915/display/intel_hdmi.c | 233 ++++++++++++++++++++++
drivers/gpu/drm/i915/display/intel_hdmi.h | 7 +
2 files changed, 240 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/intel_hdmi.c b/drivers/gpu/drm/i915/display/intel_hdmi.c
index e10fdb369daa..41eb1c175a0e 100644
--- a/drivers/gpu/drm/i915/display/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/display/intel_hdmi.c
@@ -3428,3 +3428,236 @@ void intel_hdmi_init(struct drm_i915_private *dev_priv,
dig_port->aux_ch = intel_bios_port_aux_ch(dev_priv, port);
intel_hdmi_init_connector(dig_port, intel_connector);
}
+
+/*
+ * intel_hdmi_dsc_get_slice_height - get the dsc slice_height
+ * @vactive: Vactive of a display mode
+ *
+ * @return: appropriate dsc slice height for a given mode.
+ */
+int intel_hdmi_dsc_get_slice_height(int vactive)
+{
+ int slice_height;
+
+ /*
+ * Slice Height determination : HDMI2.1 Section 7.7.5.2
+ * Select smallest slice height >=96, that results in a valid PPS and
+ * requires minimum padding lines required for final slice.
+ *
+ * Assumption : Vactive is even.
+ */
+ for (slice_height = 96; slice_height <= vactive; slice_height += 2)
+ if (vactive % slice_height == 0)
+ return slice_height;
+
+ return 0;
+}
+
+/*
+ * intel_hdmi_dsc_get_num_slices - get no. of dsc slices based on dsc encoder
+ * and dsc decoder capabilites
+ *
+ * @crtc_state: intel crtc_state
+ * @src_max_slices: maximum slices supported by the DSC encoder
+ * @src_max_slice_width: maximum slice width supported by DSC encoder
+ * @hdmi_max_slices: maximum slices supported by sink DSC decoder
+ * @hdmi_throughput: maximum clock per slice (MHz) supported by HDMI sink
+ *
+ * @return: num of dsc slices that can be supported by the dsc encoder
+ * and decoder.
+ */
+int
+intel_hdmi_dsc_get_num_slices(const struct intel_crtc_state *crtc_state,
+ int src_max_slices, int src_max_slice_width,
+ int hdmi_max_slices, int hdmi_throughput)
+{
+/* Pixel rates in KPixels/sec */
+#define HDMI_DSC_PEAK_PIXEL_RATE 2720000
+/*
+ * Rates at which the source and sink are required to process pixels in each
+ * slice, can be two levels: either atleast 340000KHz or atleast 40000KHz.
+ */
+#define HDMI_DSC_MAX_ENC_THROUGHPUT_0 340000
+#define HDMI_DSC_MAX_ENC_THROUGHPUT_1 400000
+
+/* Spec limits the slice width to 2720 pixels */
+#define MAX_HDMI_SLICE_WIDTH 2720
+ int kslice_adjust;
+ int adjusted_clk_khz;
+ int min_slices;
+ int target_slices;
+ int max_throughput; /* max clock freq. in khz per slice */
+ int max_slice_width;
+ int slice_width;
+ int pixel_clock = crtc_state->hw.adjusted_mode.crtc_clock;
+
+ if (!hdmi_throughput)
+ return 0;
+
+ /*
+ * Slice Width determination : HDMI2.1 Section 7.7.5.1
+ * kslice_adjust factor for 4:2:0, and 4:2:2 formats is 0.5, where as
+ * for 4:4:4 is 1.0. Multiplying these factors by 10 and later
+ * dividing adjusted clock value by 10.
+ */
+ if (crtc_state->output_format == INTEL_OUTPUT_FORMAT_YCBCR444 ||
+ crtc_state->output_format == INTEL_OUTPUT_FORMAT_RGB)
+ kslice_adjust = 10;
+ else
+ kslice_adjust = 5;
+
+ /*
+ * As per spec, the rate at which the source and the sink process
+ * the pixels per slice are at two levels: atleast 340Mhz or 400Mhz.
+ * This depends upon the pixel clock rate and output formats
+ * (kslice adjust).
+ * If pixel clock * kslice adjust >= 2720MHz slices can be processed
+ * at max 340MHz, otherwise they can be processed at max 400MHz.
+ */
+
+ adjusted_clk_khz = DIV_ROUND_UP(kslice_adjust * pixel_clock, 10);
+
+ if (adjusted_clk_khz <= HDMI_DSC_PEAK_PIXEL_RATE)
+ max_throughput = HDMI_DSC_MAX_ENC_THROUGHPUT_0;
+ else
+ max_throughput = HDMI_DSC_MAX_ENC_THROUGHPUT_1;
+
+ /*
+ * Taking into account the sink's capability for maximum
+ * clock per slice (in MHz) as read from HF-VSDB.
+ */
+ max_throughput = min(max_throughput, hdmi_throughput * 1000);
+
+ min_slices = DIV_ROUND_UP(adjusted_clk_khz, max_throughput);
+ max_slice_width = min(MAX_HDMI_SLICE_WIDTH, src_max_slice_width);
+
+ /*
+ * Keep on increasing the num of slices/line, starting from min_slices
+ * per line till we get such a number, for which the slice_width is
+ * just less than max_slice_width. The slices/line selected should be
+ * less than or equal to the max horizontal slices that the combination
+ * of PCON encoder and HDMI decoder can support.
+ */
+ slice_width = max_slice_width;
+
+ do {
+ if (min_slices <= 1 && src_max_slices >= 1 && hdmi_max_slices >= 1)
+ target_slices = 1;
+ else if (min_slices <= 2 && src_max_slices >= 2 && hdmi_max_slices >= 2)
+ target_slices = 2;
+ else if (min_slices <= 4 && src_max_slices >= 4 && hdmi_max_slices >= 4)
+ target_slices = 4;
+ else if (min_slices <= 8 && src_max_slices >= 8 && hdmi_max_slices >= 8)
+ target_slices = 8;
+ else if (min_slices <= 12 && src_max_slices >= 12 && hdmi_max_slices >= 12)
+ target_slices = 12;
+ else if (min_slices <= 16 && src_max_slices >= 16 && hdmi_max_slices >= 16)
+ target_slices = 16;
+ else
+ return 0;
+
+ slice_width = DIV_ROUND_UP(crtc_state->hw.adjusted_mode.hdisplay, target_slices);
+ if (slice_width >= max_slice_width)
+ min_slices = target_slices + 1;
+ } while (slice_width >= max_slice_width);
+
+ return target_slices;
+}
+
+/*
+ * intel_hdmi_dsc_get_bpp - get the appropriate compressed bits_per_pixel based on
+ * source and sink capabilities.
+ *
+ * @src_fraction_bpp: fractional bpp supported by the source
+ * @slice_width: dsc slice width supported by the source and sink
+ * @num_slices: num of slices supported by the source and sink
+ * @output_format: video output format
+ * @hdmi_all_bpp: sink supports decoding of 1/16th bpp setting
+ * @hdmi_max_chunk_bytes: max bytes in a line of chunks supported by sink
+ *
+ * @return: compressed bits_per_pixel in step of 1/16 of bits_per_pixel
+ */
+int
+intel_hdmi_dsc_get_bpp(int src_fractional_bpp, int slice_width, int num_slices,
+ int output_format, bool hdmi_all_bpp,
+ int hdmi_max_chunk_bytes)
+{
+ int max_dsc_bpp, min_dsc_bpp;
+ int target_bytes;
+ bool bpp_found = false;
+ int bpp_decrement_x16;
+ int bpp_target;
+ int bpp_target_x16;
+
+ /*
+ * Get min bpp and max bpp as per Table 7.23, in HDMI2.1 spec
+ * Start with the max bpp and keep on decrementing with
+ * fractional bpp, if supported by PCON DSC encoder
+ *
+ * for each bpp we check if no of bytes can be supported by HDMI sink
+ */
+
+ /* Assuming: bpc as 8*/
+ if (output_format == INTEL_OUTPUT_FORMAT_YCBCR420) {
+ min_dsc_bpp = 6;
+ max_dsc_bpp = 3 * 4; /* 3*bpc/2 */
+ } else if (output_format == INTEL_OUTPUT_FORMAT_YCBCR444 ||
+ output_format == INTEL_OUTPUT_FORMAT_RGB) {
+ min_dsc_bpp = 8;
+ max_dsc_bpp = 3 * 8; /* 3*bpc */
+ } else {
+ /* Assuming 4:2:2 encoding */
+ min_dsc_bpp = 7;
+ max_dsc_bpp = 2 * 8; /* 2*bpc */
+ }
+
+ /*
+ * Taking into account if all dsc_all_bpp supported by HDMI2.1 sink
+ * Section 7.7.34 : Source shall not enable compressed Video
+ * Transport with bpp_target settings above 12 bpp unless
+ * DSC_all_bpp is set to 1.
+ */
+ if (!hdmi_all_bpp)
+ max_dsc_bpp = min(max_dsc_bpp, 12);
+
+ /*
+ * The Sink has a limit of compressed data in bytes for a scanline,
+ * as described in max_chunk_bytes field in HFVSDB block of edid.
+ * The no. of bytes depend on the target bits per pixel that the
+ * source configures. So we start with the max_bpp and calculate
+ * the target_chunk_bytes. We keep on decrementing the target_bpp,
+ * till we get the target_chunk_bytes just less than what the sink's
+ * max_chunk_bytes, or else till we reach the min_dsc_bpp.
+ *
+ * The decrement is according to the fractional support from PCON DSC
+ * encoder. For fractional BPP we use bpp_target as a multiple of 16.
+ *
+ * bpp_target_x16 = bpp_target * 16
+ * So we need to decrement by {1, 2, 4, 8, 16} for fractional bpps
+ * {1/16, 1/8, 1/4, 1/2, 1} respectively.
+ */
+
+ bpp_target = max_dsc_bpp;
+
+ /* src does not support fractional bpp implies decrement by 16 for bppx16 */
+ if (!src_fractional_bpp)
+ src_fractional_bpp = 1;
+ bpp_decrement_x16 = DIV_ROUND_UP(16, src_fractional_bpp);
+ bpp_target_x16 = (bpp_target * 16) - bpp_decrement_x16;
+
+ while (bpp_target_x16 > (min_dsc_bpp * 16)) {
+ int bpp;
+
+ bpp = DIV_ROUND_UP(bpp_target_x16, 16);
+ target_bytes = DIV_ROUND_UP((num_slices * slice_width * bpp), 8);
+ if (target_bytes <= hdmi_max_chunk_bytes) {
+ bpp_found = true;
+ break;
+ }
+ bpp_target_x16 -= bpp_decrement_x16;
+ }
+ if (bpp_found)
+ return bpp_target_x16;
+
+ return 0;
+}
diff --git a/drivers/gpu/drm/i915/display/intel_hdmi.h b/drivers/gpu/drm/i915/display/intel_hdmi.h
index 15eb0ccde76e..fa1a9b030850 100644
--- a/drivers/gpu/drm/i915/display/intel_hdmi.h
+++ b/drivers/gpu/drm/i915/display/intel_hdmi.h
@@ -50,5 +50,12 @@ bool intel_hdmi_limited_color_range(const struct intel_crtc_state *crtc_state,
const struct drm_connector_state *conn_state);
bool intel_hdmi_deep_color_possible(const struct intel_crtc_state *crtc_state, int bpc,
bool has_hdmi_sink, bool ycbcr420_output);
+int intel_hdmi_dsc_get_bpp(int src_fractional_bpp, int slice_width,
+ int num_slices, int output_format, bool hdmi_all_bpp,
+ int hdmi_max_chunk_bytes);
+int intel_hdmi_dsc_get_num_slices(const struct intel_crtc_state *crtc_state,
+ int src_max_slices, int src_max_slice_width,
+ int hdmi_max_slices, int hdmi_throughput);
+int intel_hdmi_dsc_get_slice_height(int vactive);
#endif /* __INTEL_HDMI_H__ */
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 13/15] drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
The DP-HDMI2.1 PCON spec provides way for a source to set PPS
parameters: slice height, slice width and bits_per_pixel, based on
the HDMI2.1 sink capabilities. The DSC encoder of the PCON will
respect these parameters, while preparing the 128 byte PPS.
This patch adds helper functions to calculate these PPS paremeters as
per the HDMI2.1 specification.
v2: Addressed review comments given by Uma Shankar:
-added documentation for functions
-fixed typos and errors
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/i915/display/intel_hdmi.c | 233 ++++++++++++++++++++++
drivers/gpu/drm/i915/display/intel_hdmi.h | 7 +
2 files changed, 240 insertions(+)
diff --git a/drivers/gpu/drm/i915/display/intel_hdmi.c b/drivers/gpu/drm/i915/display/intel_hdmi.c
index e10fdb369daa..41eb1c175a0e 100644
--- a/drivers/gpu/drm/i915/display/intel_hdmi.c
+++ b/drivers/gpu/drm/i915/display/intel_hdmi.c
@@ -3428,3 +3428,236 @@ void intel_hdmi_init(struct drm_i915_private *dev_priv,
dig_port->aux_ch = intel_bios_port_aux_ch(dev_priv, port);
intel_hdmi_init_connector(dig_port, intel_connector);
}
+
+/*
+ * intel_hdmi_dsc_get_slice_height - get the dsc slice_height
+ * @vactive: Vactive of a display mode
+ *
+ * @return: appropriate dsc slice height for a given mode.
+ */
+int intel_hdmi_dsc_get_slice_height(int vactive)
+{
+ int slice_height;
+
+ /*
+ * Slice Height determination : HDMI2.1 Section 7.7.5.2
+ * Select smallest slice height >=96, that results in a valid PPS and
+ * requires minimum padding lines required for final slice.
+ *
+ * Assumption : Vactive is even.
+ */
+ for (slice_height = 96; slice_height <= vactive; slice_height += 2)
+ if (vactive % slice_height == 0)
+ return slice_height;
+
+ return 0;
+}
+
+/*
+ * intel_hdmi_dsc_get_num_slices - get no. of dsc slices based on dsc encoder
+ * and dsc decoder capabilites
+ *
+ * @crtc_state: intel crtc_state
+ * @src_max_slices: maximum slices supported by the DSC encoder
+ * @src_max_slice_width: maximum slice width supported by DSC encoder
+ * @hdmi_max_slices: maximum slices supported by sink DSC decoder
+ * @hdmi_throughput: maximum clock per slice (MHz) supported by HDMI sink
+ *
+ * @return: num of dsc slices that can be supported by the dsc encoder
+ * and decoder.
+ */
+int
+intel_hdmi_dsc_get_num_slices(const struct intel_crtc_state *crtc_state,
+ int src_max_slices, int src_max_slice_width,
+ int hdmi_max_slices, int hdmi_throughput)
+{
+/* Pixel rates in KPixels/sec */
+#define HDMI_DSC_PEAK_PIXEL_RATE 2720000
+/*
+ * Rates at which the source and sink are required to process pixels in each
+ * slice, can be two levels: either atleast 340000KHz or atleast 40000KHz.
+ */
+#define HDMI_DSC_MAX_ENC_THROUGHPUT_0 340000
+#define HDMI_DSC_MAX_ENC_THROUGHPUT_1 400000
+
+/* Spec limits the slice width to 2720 pixels */
+#define MAX_HDMI_SLICE_WIDTH 2720
+ int kslice_adjust;
+ int adjusted_clk_khz;
+ int min_slices;
+ int target_slices;
+ int max_throughput; /* max clock freq. in khz per slice */
+ int max_slice_width;
+ int slice_width;
+ int pixel_clock = crtc_state->hw.adjusted_mode.crtc_clock;
+
+ if (!hdmi_throughput)
+ return 0;
+
+ /*
+ * Slice Width determination : HDMI2.1 Section 7.7.5.1
+ * kslice_adjust factor for 4:2:0, and 4:2:2 formats is 0.5, where as
+ * for 4:4:4 is 1.0. Multiplying these factors by 10 and later
+ * dividing adjusted clock value by 10.
+ */
+ if (crtc_state->output_format == INTEL_OUTPUT_FORMAT_YCBCR444 ||
+ crtc_state->output_format == INTEL_OUTPUT_FORMAT_RGB)
+ kslice_adjust = 10;
+ else
+ kslice_adjust = 5;
+
+ /*
+ * As per spec, the rate at which the source and the sink process
+ * the pixels per slice are at two levels: atleast 340Mhz or 400Mhz.
+ * This depends upon the pixel clock rate and output formats
+ * (kslice adjust).
+ * If pixel clock * kslice adjust >= 2720MHz slices can be processed
+ * at max 340MHz, otherwise they can be processed at max 400MHz.
+ */
+
+ adjusted_clk_khz = DIV_ROUND_UP(kslice_adjust * pixel_clock, 10);
+
+ if (adjusted_clk_khz <= HDMI_DSC_PEAK_PIXEL_RATE)
+ max_throughput = HDMI_DSC_MAX_ENC_THROUGHPUT_0;
+ else
+ max_throughput = HDMI_DSC_MAX_ENC_THROUGHPUT_1;
+
+ /*
+ * Taking into account the sink's capability for maximum
+ * clock per slice (in MHz) as read from HF-VSDB.
+ */
+ max_throughput = min(max_throughput, hdmi_throughput * 1000);
+
+ min_slices = DIV_ROUND_UP(adjusted_clk_khz, max_throughput);
+ max_slice_width = min(MAX_HDMI_SLICE_WIDTH, src_max_slice_width);
+
+ /*
+ * Keep on increasing the num of slices/line, starting from min_slices
+ * per line till we get such a number, for which the slice_width is
+ * just less than max_slice_width. The slices/line selected should be
+ * less than or equal to the max horizontal slices that the combination
+ * of PCON encoder and HDMI decoder can support.
+ */
+ slice_width = max_slice_width;
+
+ do {
+ if (min_slices <= 1 && src_max_slices >= 1 && hdmi_max_slices >= 1)
+ target_slices = 1;
+ else if (min_slices <= 2 && src_max_slices >= 2 && hdmi_max_slices >= 2)
+ target_slices = 2;
+ else if (min_slices <= 4 && src_max_slices >= 4 && hdmi_max_slices >= 4)
+ target_slices = 4;
+ else if (min_slices <= 8 && src_max_slices >= 8 && hdmi_max_slices >= 8)
+ target_slices = 8;
+ else if (min_slices <= 12 && src_max_slices >= 12 && hdmi_max_slices >= 12)
+ target_slices = 12;
+ else if (min_slices <= 16 && src_max_slices >= 16 && hdmi_max_slices >= 16)
+ target_slices = 16;
+ else
+ return 0;
+
+ slice_width = DIV_ROUND_UP(crtc_state->hw.adjusted_mode.hdisplay, target_slices);
+ if (slice_width >= max_slice_width)
+ min_slices = target_slices + 1;
+ } while (slice_width >= max_slice_width);
+
+ return target_slices;
+}
+
+/*
+ * intel_hdmi_dsc_get_bpp - get the appropriate compressed bits_per_pixel based on
+ * source and sink capabilities.
+ *
+ * @src_fraction_bpp: fractional bpp supported by the source
+ * @slice_width: dsc slice width supported by the source and sink
+ * @num_slices: num of slices supported by the source and sink
+ * @output_format: video output format
+ * @hdmi_all_bpp: sink supports decoding of 1/16th bpp setting
+ * @hdmi_max_chunk_bytes: max bytes in a line of chunks supported by sink
+ *
+ * @return: compressed bits_per_pixel in step of 1/16 of bits_per_pixel
+ */
+int
+intel_hdmi_dsc_get_bpp(int src_fractional_bpp, int slice_width, int num_slices,
+ int output_format, bool hdmi_all_bpp,
+ int hdmi_max_chunk_bytes)
+{
+ int max_dsc_bpp, min_dsc_bpp;
+ int target_bytes;
+ bool bpp_found = false;
+ int bpp_decrement_x16;
+ int bpp_target;
+ int bpp_target_x16;
+
+ /*
+ * Get min bpp and max bpp as per Table 7.23, in HDMI2.1 spec
+ * Start with the max bpp and keep on decrementing with
+ * fractional bpp, if supported by PCON DSC encoder
+ *
+ * for each bpp we check if no of bytes can be supported by HDMI sink
+ */
+
+ /* Assuming: bpc as 8*/
+ if (output_format == INTEL_OUTPUT_FORMAT_YCBCR420) {
+ min_dsc_bpp = 6;
+ max_dsc_bpp = 3 * 4; /* 3*bpc/2 */
+ } else if (output_format == INTEL_OUTPUT_FORMAT_YCBCR444 ||
+ output_format == INTEL_OUTPUT_FORMAT_RGB) {
+ min_dsc_bpp = 8;
+ max_dsc_bpp = 3 * 8; /* 3*bpc */
+ } else {
+ /* Assuming 4:2:2 encoding */
+ min_dsc_bpp = 7;
+ max_dsc_bpp = 2 * 8; /* 2*bpc */
+ }
+
+ /*
+ * Taking into account if all dsc_all_bpp supported by HDMI2.1 sink
+ * Section 7.7.34 : Source shall not enable compressed Video
+ * Transport with bpp_target settings above 12 bpp unless
+ * DSC_all_bpp is set to 1.
+ */
+ if (!hdmi_all_bpp)
+ max_dsc_bpp = min(max_dsc_bpp, 12);
+
+ /*
+ * The Sink has a limit of compressed data in bytes for a scanline,
+ * as described in max_chunk_bytes field in HFVSDB block of edid.
+ * The no. of bytes depend on the target bits per pixel that the
+ * source configures. So we start with the max_bpp and calculate
+ * the target_chunk_bytes. We keep on decrementing the target_bpp,
+ * till we get the target_chunk_bytes just less than what the sink's
+ * max_chunk_bytes, or else till we reach the min_dsc_bpp.
+ *
+ * The decrement is according to the fractional support from PCON DSC
+ * encoder. For fractional BPP we use bpp_target as a multiple of 16.
+ *
+ * bpp_target_x16 = bpp_target * 16
+ * So we need to decrement by {1, 2, 4, 8, 16} for fractional bpps
+ * {1/16, 1/8, 1/4, 1/2, 1} respectively.
+ */
+
+ bpp_target = max_dsc_bpp;
+
+ /* src does not support fractional bpp implies decrement by 16 for bppx16 */
+ if (!src_fractional_bpp)
+ src_fractional_bpp = 1;
+ bpp_decrement_x16 = DIV_ROUND_UP(16, src_fractional_bpp);
+ bpp_target_x16 = (bpp_target * 16) - bpp_decrement_x16;
+
+ while (bpp_target_x16 > (min_dsc_bpp * 16)) {
+ int bpp;
+
+ bpp = DIV_ROUND_UP(bpp_target_x16, 16);
+ target_bytes = DIV_ROUND_UP((num_slices * slice_width * bpp), 8);
+ if (target_bytes <= hdmi_max_chunk_bytes) {
+ bpp_found = true;
+ break;
+ }
+ bpp_target_x16 -= bpp_decrement_x16;
+ }
+ if (bpp_found)
+ return bpp_target_x16;
+
+ return 0;
+}
diff --git a/drivers/gpu/drm/i915/display/intel_hdmi.h b/drivers/gpu/drm/i915/display/intel_hdmi.h
index 15eb0ccde76e..fa1a9b030850 100644
--- a/drivers/gpu/drm/i915/display/intel_hdmi.h
+++ b/drivers/gpu/drm/i915/display/intel_hdmi.h
@@ -50,5 +50,12 @@ bool intel_hdmi_limited_color_range(const struct intel_crtc_state *crtc_state,
const struct drm_connector_state *conn_state);
bool intel_hdmi_deep_color_possible(const struct intel_crtc_state *crtc_state, int bpc,
bool has_hdmi_sink, bool ycbcr420_output);
+int intel_hdmi_dsc_get_bpp(int src_fractional_bpp, int slice_width,
+ int num_slices, int output_format, bool hdmi_all_bpp,
+ int hdmi_max_chunk_bytes);
+int intel_hdmi_dsc_get_num_slices(const struct intel_crtc_state *crtc_state,
+ int src_max_slices, int src_max_slice_width,
+ int hdmi_max_slices, int hdmi_throughput);
+int intel_hdmi_dsc_get_slice_height(int vactive);
#endif /* __INTEL_HDMI_H__ */
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 14/15] drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink
via DP HDMI2.1 PCON, the PCON can be configured to decode the
DSC1.1 compressed stream and encode to DSC1.2. It then sends the
DSC1.2 compressed stream to the HDMI2.1 sink.
This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based
on the PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder
capabilities.
v2: Addressed review comments from Uma Shankar:
-fixed the error in packing pps parameter values
-added check for pcon in the pcon related function
-appended display in commit message
v3: Only consider non-zero DSC FRL b/w for determining max FRL b/w
supported by sink.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/i915/display/intel_ddi.c | 1 +
drivers/gpu/drm/i915/display/intel_dp.c | 118 ++++++++++++++++++++++-
drivers/gpu/drm/i915/display/intel_dp.h | 2 +
3 files changed, 119 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index 974cf42351bc..fbc07a93504b 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -3653,6 +3653,7 @@ static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
intel_dp_check_frl_training(intel_dp);
+ intel_dp_pcon_dsc_configure(intel_dp, crtc_state);
/*
* 7.i Follow DisplayPort specification training sequence (see notes for
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 7e2c334b3a17..fdc028b7db07 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -4043,9 +4043,22 @@ static int intel_dp_hdmi_sink_max_frl(struct intel_dp *intel_dp)
{
struct intel_connector *intel_connector = intel_dp->attached_connector;
struct drm_connector *connector = &intel_connector->base;
+ int max_frl_rate;
+ int max_lanes, rate_per_lane;
+ int max_dsc_lanes, dsc_rate_per_lane;
- return (connector->display_info.hdmi.max_frl_rate_per_lane *
- connector->display_info.hdmi.max_lanes);
+ max_lanes = connector->display_info.hdmi.max_lanes;
+ rate_per_lane = connector->display_info.hdmi.max_frl_rate_per_lane;
+ max_frl_rate = max_lanes * rate_per_lane;
+
+ if (connector->display_info.hdmi.dsc_cap.v_1p2) {
+ max_dsc_lanes = connector->display_info.hdmi.dsc_cap.max_lanes;
+ dsc_rate_per_lane = connector->display_info.hdmi.dsc_cap.max_frl_rate_per_lane;
+ if (max_dsc_lanes && dsc_rate_per_lane)
+ max_frl_rate = min(max_frl_rate, max_dsc_lanes * dsc_rate_per_lane);
+ }
+
+ return max_frl_rate;
}
static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
@@ -4152,6 +4165,105 @@ void intel_dp_check_frl_training(struct intel_dp *intel_dp)
}
}
+static int
+intel_dp_pcon_dsc_enc_slice_height(const struct intel_crtc_state *crtc_state)
+{
+
+ int vactive = crtc_state->hw.adjusted_mode.vdisplay;
+
+ return intel_hdmi_dsc_get_slice_height(vactive);
+}
+
+static int
+intel_dp_pcon_dsc_enc_slices(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state)
+{
+ struct intel_connector *intel_connector = intel_dp->attached_connector;
+ struct drm_connector *connector = &intel_connector->base;
+ int hdmi_throughput = connector->display_info.hdmi.dsc_cap.clk_per_slice;
+ int hdmi_max_slices = connector->display_info.hdmi.dsc_cap.max_slices;
+ int pcon_max_slices = drm_dp_pcon_dsc_max_slices(intel_dp->pcon_dsc_dpcd);
+ int pcon_max_slice_width = drm_dp_pcon_dsc_max_slice_width(intel_dp->pcon_dsc_dpcd);
+
+
+ return intel_hdmi_dsc_get_num_slices(crtc_state, pcon_max_slices,
+ pcon_max_slice_width,
+ hdmi_max_slices, hdmi_throughput);
+}
+
+static int
+intel_dp_pcon_dsc_enc_bpp(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state,
+ int num_slices, int slice_width)
+{
+ struct intel_connector *intel_connector = intel_dp->attached_connector;
+ struct drm_connector *connector = &intel_connector->base;
+ int output_format = crtc_state->output_format;
+ bool hdmi_all_bpp = connector->display_info.hdmi.dsc_cap.all_bpp;
+ int pcon_fractional_bpp = drm_dp_pcon_dsc_bpp_incr(intel_dp->pcon_dsc_dpcd);
+ int hdmi_max_chunk_bytes =
+ connector->display_info.hdmi.dsc_cap.total_chunk_kbytes * 1024;
+
+ return intel_hdmi_dsc_get_bpp(pcon_fractional_bpp, slice_width,
+ num_slices, output_format, hdmi_all_bpp,
+ hdmi_max_chunk_bytes);
+}
+
+void
+intel_dp_pcon_dsc_configure(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state)
+{
+ u8 pps_param[6];
+ int slice_height;
+ int slice_width;
+ int num_slices;
+ int bits_per_pixel;
+ int ret;
+ struct intel_connector *intel_connector = intel_dp->attached_connector;
+ struct drm_i915_private *i915 = dp_to_i915(intel_dp);
+ struct drm_connector *connector;
+ bool hdmi_is_dsc_1_2;
+
+ if (!intel_dp_is_hdmi_2_1_sink(intel_dp))
+ return;
+
+ if (!intel_connector)
+ return;
+ connector = &intel_connector->base;
+ hdmi_is_dsc_1_2 = connector->display_info.hdmi.dsc_cap.v_1p2;
+
+ if (!drm_dp_pcon_enc_is_dsc_1_2(intel_dp->pcon_dsc_dpcd) ||
+ !hdmi_is_dsc_1_2)
+ return;
+
+ slice_height = intel_dp_pcon_dsc_enc_slice_height(crtc_state);
+ if (!slice_height)
+ return;
+
+ num_slices = intel_dp_pcon_dsc_enc_slices(intel_dp, crtc_state);
+ if (!num_slices)
+ return;
+
+ slice_width = DIV_ROUND_UP(crtc_state->hw.adjusted_mode.hdisplay,
+ num_slices);
+
+ bits_per_pixel = intel_dp_pcon_dsc_enc_bpp(intel_dp, crtc_state,
+ num_slices, slice_width);
+ if (!bits_per_pixel)
+ return;
+
+ pps_param[0] = slice_height & 0xFF;
+ pps_param[1] = slice_height >> 8;
+ pps_param[2] = slice_width & 0xFF;
+ pps_param[3] = slice_width >> 8;
+ pps_param[4] = bits_per_pixel & 0xFF;
+ pps_param[5] = (bits_per_pixel >> 8) & 0x3;
+
+ ret = drm_dp_pcon_pps_override_param(&intel_dp->aux, pps_param);
+ if (ret < 0)
+ drm_dbg_kms(&i915->drm, "Failed to set pcon DSC\n");
+}
+
static void
g4x_set_link_train(struct intel_dp *intel_dp,
const struct intel_crtc_state *crtc_state,
@@ -4283,6 +4395,7 @@ static void intel_enable_dp(struct intel_atomic_state *state,
intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
intel_dp_configure_protocol_converter(intel_dp);
intel_dp_check_frl_training(intel_dp);
+ intel_dp_pcon_dsc_configure(intel_dp, pipe_config);
intel_dp_start_link_train(intel_dp, pipe_config);
intel_dp_stop_link_train(intel_dp, pipe_config);
@@ -6227,6 +6340,7 @@ int intel_dp_retrain_link(struct intel_encoder *encoder,
continue;
intel_dp_check_frl_training(intel_dp);
+ intel_dp_pcon_dsc_configure(intel_dp, crtc_state);
intel_dp_start_link_train(intel_dp, crtc_state);
intel_dp_stop_link_train(intel_dp, crtc_state);
break;
diff --git a/drivers/gpu/drm/i915/display/intel_dp.h b/drivers/gpu/drm/i915/display/intel_dp.h
index 58b76a20459c..1bfde4f89019 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.h
+++ b/drivers/gpu/drm/i915/display/intel_dp.h
@@ -145,5 +145,7 @@ void intel_dp_sync_state(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state);
void intel_dp_check_frl_training(struct intel_dp *intel_dp);
+void intel_dp_pcon_dsc_configure(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state);
#endif /* __INTEL_DP_H__ */
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 14/15] drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink
via DP HDMI2.1 PCON, the PCON can be configured to decode the
DSC1.1 compressed stream and encode to DSC1.2. It then sends the
DSC1.2 compressed stream to the HDMI2.1 sink.
This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based
on the PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder
capabilities.
v2: Addressed review comments from Uma Shankar:
-fixed the error in packing pps parameter values
-added check for pcon in the pcon related function
-appended display in commit message
v3: Only consider non-zero DSC FRL b/w for determining max FRL b/w
supported by sink.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
---
drivers/gpu/drm/i915/display/intel_ddi.c | 1 +
drivers/gpu/drm/i915/display/intel_dp.c | 118 ++++++++++++++++++++++-
drivers/gpu/drm/i915/display/intel_dp.h | 2 +
3 files changed, 119 insertions(+), 2 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index 974cf42351bc..fbc07a93504b 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -3653,6 +3653,7 @@ static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
intel_dp_check_frl_training(intel_dp);
+ intel_dp_pcon_dsc_configure(intel_dp, crtc_state);
/*
* 7.i Follow DisplayPort specification training sequence (see notes for
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index 7e2c334b3a17..fdc028b7db07 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -4043,9 +4043,22 @@ static int intel_dp_hdmi_sink_max_frl(struct intel_dp *intel_dp)
{
struct intel_connector *intel_connector = intel_dp->attached_connector;
struct drm_connector *connector = &intel_connector->base;
+ int max_frl_rate;
+ int max_lanes, rate_per_lane;
+ int max_dsc_lanes, dsc_rate_per_lane;
- return (connector->display_info.hdmi.max_frl_rate_per_lane *
- connector->display_info.hdmi.max_lanes);
+ max_lanes = connector->display_info.hdmi.max_lanes;
+ rate_per_lane = connector->display_info.hdmi.max_frl_rate_per_lane;
+ max_frl_rate = max_lanes * rate_per_lane;
+
+ if (connector->display_info.hdmi.dsc_cap.v_1p2) {
+ max_dsc_lanes = connector->display_info.hdmi.dsc_cap.max_lanes;
+ dsc_rate_per_lane = connector->display_info.hdmi.dsc_cap.max_frl_rate_per_lane;
+ if (max_dsc_lanes && dsc_rate_per_lane)
+ max_frl_rate = min(max_frl_rate, max_dsc_lanes * dsc_rate_per_lane);
+ }
+
+ return max_frl_rate;
}
static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
@@ -4152,6 +4165,105 @@ void intel_dp_check_frl_training(struct intel_dp *intel_dp)
}
}
+static int
+intel_dp_pcon_dsc_enc_slice_height(const struct intel_crtc_state *crtc_state)
+{
+
+ int vactive = crtc_state->hw.adjusted_mode.vdisplay;
+
+ return intel_hdmi_dsc_get_slice_height(vactive);
+}
+
+static int
+intel_dp_pcon_dsc_enc_slices(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state)
+{
+ struct intel_connector *intel_connector = intel_dp->attached_connector;
+ struct drm_connector *connector = &intel_connector->base;
+ int hdmi_throughput = connector->display_info.hdmi.dsc_cap.clk_per_slice;
+ int hdmi_max_slices = connector->display_info.hdmi.dsc_cap.max_slices;
+ int pcon_max_slices = drm_dp_pcon_dsc_max_slices(intel_dp->pcon_dsc_dpcd);
+ int pcon_max_slice_width = drm_dp_pcon_dsc_max_slice_width(intel_dp->pcon_dsc_dpcd);
+
+
+ return intel_hdmi_dsc_get_num_slices(crtc_state, pcon_max_slices,
+ pcon_max_slice_width,
+ hdmi_max_slices, hdmi_throughput);
+}
+
+static int
+intel_dp_pcon_dsc_enc_bpp(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state,
+ int num_slices, int slice_width)
+{
+ struct intel_connector *intel_connector = intel_dp->attached_connector;
+ struct drm_connector *connector = &intel_connector->base;
+ int output_format = crtc_state->output_format;
+ bool hdmi_all_bpp = connector->display_info.hdmi.dsc_cap.all_bpp;
+ int pcon_fractional_bpp = drm_dp_pcon_dsc_bpp_incr(intel_dp->pcon_dsc_dpcd);
+ int hdmi_max_chunk_bytes =
+ connector->display_info.hdmi.dsc_cap.total_chunk_kbytes * 1024;
+
+ return intel_hdmi_dsc_get_bpp(pcon_fractional_bpp, slice_width,
+ num_slices, output_format, hdmi_all_bpp,
+ hdmi_max_chunk_bytes);
+}
+
+void
+intel_dp_pcon_dsc_configure(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state)
+{
+ u8 pps_param[6];
+ int slice_height;
+ int slice_width;
+ int num_slices;
+ int bits_per_pixel;
+ int ret;
+ struct intel_connector *intel_connector = intel_dp->attached_connector;
+ struct drm_i915_private *i915 = dp_to_i915(intel_dp);
+ struct drm_connector *connector;
+ bool hdmi_is_dsc_1_2;
+
+ if (!intel_dp_is_hdmi_2_1_sink(intel_dp))
+ return;
+
+ if (!intel_connector)
+ return;
+ connector = &intel_connector->base;
+ hdmi_is_dsc_1_2 = connector->display_info.hdmi.dsc_cap.v_1p2;
+
+ if (!drm_dp_pcon_enc_is_dsc_1_2(intel_dp->pcon_dsc_dpcd) ||
+ !hdmi_is_dsc_1_2)
+ return;
+
+ slice_height = intel_dp_pcon_dsc_enc_slice_height(crtc_state);
+ if (!slice_height)
+ return;
+
+ num_slices = intel_dp_pcon_dsc_enc_slices(intel_dp, crtc_state);
+ if (!num_slices)
+ return;
+
+ slice_width = DIV_ROUND_UP(crtc_state->hw.adjusted_mode.hdisplay,
+ num_slices);
+
+ bits_per_pixel = intel_dp_pcon_dsc_enc_bpp(intel_dp, crtc_state,
+ num_slices, slice_width);
+ if (!bits_per_pixel)
+ return;
+
+ pps_param[0] = slice_height & 0xFF;
+ pps_param[1] = slice_height >> 8;
+ pps_param[2] = slice_width & 0xFF;
+ pps_param[3] = slice_width >> 8;
+ pps_param[4] = bits_per_pixel & 0xFF;
+ pps_param[5] = (bits_per_pixel >> 8) & 0x3;
+
+ ret = drm_dp_pcon_pps_override_param(&intel_dp->aux, pps_param);
+ if (ret < 0)
+ drm_dbg_kms(&i915->drm, "Failed to set pcon DSC\n");
+}
+
static void
g4x_set_link_train(struct intel_dp *intel_dp,
const struct intel_crtc_state *crtc_state,
@@ -4283,6 +4395,7 @@ static void intel_enable_dp(struct intel_atomic_state *state,
intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
intel_dp_configure_protocol_converter(intel_dp);
intel_dp_check_frl_training(intel_dp);
+ intel_dp_pcon_dsc_configure(intel_dp, pipe_config);
intel_dp_start_link_train(intel_dp, pipe_config);
intel_dp_stop_link_train(intel_dp, pipe_config);
@@ -6227,6 +6340,7 @@ int intel_dp_retrain_link(struct intel_encoder *encoder,
continue;
intel_dp_check_frl_training(intel_dp);
+ intel_dp_pcon_dsc_configure(intel_dp, crtc_state);
intel_dp_start_link_train(intel_dp, crtc_state);
intel_dp_stop_link_train(intel_dp, crtc_state);
break;
diff --git a/drivers/gpu/drm/i915/display/intel_dp.h b/drivers/gpu/drm/i915/display/intel_dp.h
index 58b76a20459c..1bfde4f89019 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.h
+++ b/drivers/gpu/drm/i915/display/intel_dp.h
@@ -145,5 +145,7 @@ void intel_dp_sync_state(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state);
void intel_dp_check_frl_training(struct intel_dp *intel_dp);
+void intel_dp_pcon_dsc_configure(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state);
#endif /* __INTEL_DP_H__ */
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [PATCH v7 15/15] drm/i915/display: Let PCON convert from RGB to YCbCr if it can
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 10:37 ` Ankit Nautiyal
-1 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx
Cc: swati2.sharma, airlied, vandita.kulkarni, uma.shankar, dri-devel
If PCON has capability to convert RGB->YCbCr colorspace and also
to 444->420 downsampling then for any YUV420 only mode, we can
let the PCON do all the conversion. If the PCON supports
RGB->YCbCr conversion for all BT2020, BT709, BT601, choose
the one that is selected by userspace via connector colorspace
property, otherwise default to BT601.
v2: As suggested by Uma Shankar, considered case for colorspace
BT709 and BT2020, and default to BT601. Also appended dir
'display' in commit message.
v3: Fixed typo in condition for printing one of the error msg.
v4: As suggested by Uma Shankar:
-Fixed bug in determining the colorspace for RGB->YCbCr conversion.
-Fixed minor formatting issues
Also updated the commit message as per latest changes.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
---
drivers/gpu/drm/i915/display/intel_ddi.c | 3 +-
.../drm/i915/display/intel_display_types.h | 1 +
drivers/gpu/drm/i915/display/intel_dp.c | 72 +++++++++++++++----
drivers/gpu/drm/i915/display/intel_dp.h | 3 +-
4 files changed, 65 insertions(+), 14 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index fbc07a93504b..17eaa56c5a99 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -3644,6 +3644,7 @@ static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
if (!is_mst)
intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
+ intel_dp_configure_protocol_converter(intel_dp, crtc_state);
intel_dp_sink_set_decompression_state(intel_dp, crtc_state, true);
/*
* DDI FEC: "anticipates enabling FEC encoding sets the FEC_READY bit
@@ -3731,7 +3732,7 @@ static void hsw_ddi_pre_enable_dp(struct intel_atomic_state *state,
intel_ddi_init_dp_buf_reg(encoder, crtc_state);
if (!is_mst)
intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
- intel_dp_configure_protocol_converter(intel_dp);
+ intel_dp_configure_protocol_converter(intel_dp, crtc_state);
intel_dp_sink_set_decompression_state(intel_dp, crtc_state,
true);
intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index 4c01c7c23dfd..2009ae9e9678 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -1460,6 +1460,7 @@ struct intel_dp {
int pcon_max_frl_bw;
u8 max_bpc;
bool ycbcr_444_to_420;
+ bool rgb_to_ycbcr;
} dfp;
/* Display stream compression testing */
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index fdc028b7db07..d7e01482c808 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -651,6 +651,10 @@ intel_dp_output_format(struct drm_connector *connector,
!drm_mode_is_420_only(info, mode))
return INTEL_OUTPUT_FORMAT_RGB;
+ if (intel_dp->dfp.rgb_to_ycbcr &&
+ intel_dp->dfp.ycbcr_444_to_420)
+ return INTEL_OUTPUT_FORMAT_RGB;
+
if (intel_dp->dfp.ycbcr_444_to_420)
return INTEL_OUTPUT_FORMAT_YCBCR444;
else
@@ -4319,7 +4323,8 @@ static void intel_dp_enable_port(struct intel_dp *intel_dp,
intel_de_posting_read(dev_priv, intel_dp->output_reg);
}
-void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp)
+void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state)
{
struct drm_i915_private *i915 = dp_to_i915(intel_dp);
u8 tmp;
@@ -4348,12 +4353,42 @@ void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp)
enableddisabled(intel_dp->dfp.ycbcr_444_to_420));
tmp = 0;
+ if (intel_dp->dfp.rgb_to_ycbcr) {
+ bool bt2020, bt709;
- if (drm_dp_dpcd_writeb(&intel_dp->aux,
- DP_PROTOCOL_CONVERTER_CONTROL_2, tmp) <= 0)
+ /*
+ * FIXME: Currently if userspace selects BT2020 or BT709, but PCON supports only
+ * RGB->YCbCr for BT601 colorspace, we go ahead with BT601, as default.
+ *
+ */
+ tmp = DP_CONVERSION_BT601_RGB_YCBCR_ENABLE;
+
+ bt2020 = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
+ intel_dp->downstream_ports,
+ DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
+ bt709 = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
+ intel_dp->downstream_ports,
+ DP_DS_HDMI_BT709_RGB_YCBCR_CONV);
+ switch (crtc_state->infoframes.vsc.colorimetry) {
+ case DP_COLORIMETRY_BT2020_RGB:
+ case DP_COLORIMETRY_BT2020_YCC:
+ if (bt2020)
+ tmp = DP_CONVERSION_BT2020_RGB_YCBCR_ENABLE;
+ break;
+ case DP_COLORIMETRY_BT709_YCC:
+ case DP_COLORIMETRY_XVYCC_709:
+ if (bt709)
+ tmp = DP_CONVERSION_BT709_RGB_YCBCR_ENABLE;
+ break;
+ default:
+ break;
+ }
+ }
+
+ if (drm_dp_pcon_convert_rgb_to_ycbcr(&intel_dp->aux, tmp) < 0)
drm_dbg_kms(&i915->drm,
- "Failed to set protocol converter YCbCr 4:2:2 conversion mode to %s\n",
- enableddisabled(false));
+ "Failed to set protocol converter RGB->YCbCr conversion mode to %s\n",
+ enableddisabled(tmp ? true : false));
}
static void intel_enable_dp(struct intel_atomic_state *state,
@@ -4393,7 +4428,7 @@ static void intel_enable_dp(struct intel_atomic_state *state,
}
intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
- intel_dp_configure_protocol_converter(intel_dp);
+ intel_dp_configure_protocol_converter(intel_dp, pipe_config);
intel_dp_check_frl_training(intel_dp);
intel_dp_pcon_dsc_configure(intel_dp, pipe_config);
intel_dp_start_link_train(intel_dp, pipe_config);
@@ -6861,7 +6896,7 @@ intel_dp_update_420(struct intel_dp *intel_dp)
{
struct drm_i915_private *i915 = dp_to_i915(intel_dp);
struct intel_connector *connector = intel_dp->attached_connector;
- bool is_branch, ycbcr_420_passthrough, ycbcr_444_to_420;
+ bool is_branch, ycbcr_420_passthrough, ycbcr_444_to_420, rgb_to_ycbcr;
/* No YCbCr output support on gmch platforms */
if (HAS_GMCH(i915))
@@ -6883,14 +6918,26 @@ intel_dp_update_420(struct intel_dp *intel_dp)
dp_to_dig_port(intel_dp)->lspcon.active ||
drm_dp_downstream_444_to_420_conversion(intel_dp->dpcd,
intel_dp->downstream_ports);
+ rgb_to_ycbcr = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
+ intel_dp->downstream_ports,
+ DP_DS_HDMI_BT601_RGB_YCBCR_CONV ||
+ DP_DS_HDMI_BT709_RGB_YCBCR_CONV ||
+ DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
if (INTEL_GEN(i915) >= 11) {
+ /* Let PCON convert from RGB->YCbCr if possible */
+ if (is_branch && rgb_to_ycbcr && ycbcr_444_to_420) {
+ intel_dp->dfp.rgb_to_ycbcr = true;
+ intel_dp->dfp.ycbcr_444_to_420 = true;
+ connector->base.ycbcr_420_allowed = true;
+ } else {
/* Prefer 4:2:0 passthrough over 4:4:4->4:2:0 conversion */
- intel_dp->dfp.ycbcr_444_to_420 =
- ycbcr_444_to_420 && !ycbcr_420_passthrough;
+ intel_dp->dfp.ycbcr_444_to_420 =
+ ycbcr_444_to_420 && !ycbcr_420_passthrough;
- connector->base.ycbcr_420_allowed =
- !is_branch || ycbcr_444_to_420 || ycbcr_420_passthrough;
+ connector->base.ycbcr_420_allowed =
+ !is_branch || ycbcr_444_to_420 || ycbcr_420_passthrough;
+ }
} else {
/* 4:4:4->4:2:0 conversion is the only way */
intel_dp->dfp.ycbcr_444_to_420 = ycbcr_444_to_420;
@@ -6899,8 +6946,9 @@ intel_dp_update_420(struct intel_dp *intel_dp)
}
drm_dbg_kms(&i915->drm,
- "[CONNECTOR:%d:%s] YCbCr 4:2:0 allowed? %s, YCbCr 4:4:4->4:2:0 conversion? %s\n",
+ "[CONNECTOR:%d:%s] RGB->YcbCr conversion? %s, YCbCr 4:2:0 allowed? %s, YCbCr 4:4:4->4:2:0 conversion? %s\n",
connector->base.base.id, connector->base.name,
+ yesno(intel_dp->dfp.rgb_to_ycbcr),
yesno(connector->base.ycbcr_420_allowed),
yesno(intel_dp->dfp.ycbcr_444_to_420));
}
diff --git a/drivers/gpu/drm/i915/display/intel_dp.h b/drivers/gpu/drm/i915/display/intel_dp.h
index 1bfde4f89019..4280a09fd8fd 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.h
+++ b/drivers/gpu/drm/i915/display/intel_dp.h
@@ -51,7 +51,8 @@ int intel_dp_get_link_train_fallback_values(struct intel_dp *intel_dp,
int intel_dp_retrain_link(struct intel_encoder *encoder,
struct drm_modeset_acquire_ctx *ctx);
void intel_dp_set_power(struct intel_dp *intel_dp, u8 mode);
-void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp);
+void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state);
void intel_dp_sink_set_decompression_state(struct intel_dp *intel_dp,
const struct intel_crtc_state *crtc_state,
bool enable);
--
2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related [flat|nested] 57+ messages in thread
* [Intel-gfx] [PATCH v7 15/15] drm/i915/display: Let PCON convert from RGB to YCbCr if it can
@ 2020-12-18 10:37 ` Ankit Nautiyal
0 siblings, 0 replies; 57+ messages in thread
From: Ankit Nautiyal @ 2020-12-18 10:37 UTC (permalink / raw)
To: intel-gfx; +Cc: airlied, dri-devel
If PCON has capability to convert RGB->YCbCr colorspace and also
to 444->420 downsampling then for any YUV420 only mode, we can
let the PCON do all the conversion. If the PCON supports
RGB->YCbCr conversion for all BT2020, BT709, BT601, choose
the one that is selected by userspace via connector colorspace
property, otherwise default to BT601.
v2: As suggested by Uma Shankar, considered case for colorspace
BT709 and BT2020, and default to BT601. Also appended dir
'display' in commit message.
v3: Fixed typo in condition for printing one of the error msg.
v4: As suggested by Uma Shankar:
-Fixed bug in determining the colorspace for RGB->YCbCr conversion.
-Fixed minor formatting issues
Also updated the commit message as per latest changes.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
---
drivers/gpu/drm/i915/display/intel_ddi.c | 3 +-
.../drm/i915/display/intel_display_types.h | 1 +
drivers/gpu/drm/i915/display/intel_dp.c | 72 +++++++++++++++----
drivers/gpu/drm/i915/display/intel_dp.h | 3 +-
4 files changed, 65 insertions(+), 14 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index fbc07a93504b..17eaa56c5a99 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -3644,6 +3644,7 @@ static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
if (!is_mst)
intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
+ intel_dp_configure_protocol_converter(intel_dp, crtc_state);
intel_dp_sink_set_decompression_state(intel_dp, crtc_state, true);
/*
* DDI FEC: "anticipates enabling FEC encoding sets the FEC_READY bit
@@ -3731,7 +3732,7 @@ static void hsw_ddi_pre_enable_dp(struct intel_atomic_state *state,
intel_ddi_init_dp_buf_reg(encoder, crtc_state);
if (!is_mst)
intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
- intel_dp_configure_protocol_converter(intel_dp);
+ intel_dp_configure_protocol_converter(intel_dp, crtc_state);
intel_dp_sink_set_decompression_state(intel_dp, crtc_state,
true);
intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h b/drivers/gpu/drm/i915/display/intel_display_types.h
index 4c01c7c23dfd..2009ae9e9678 100644
--- a/drivers/gpu/drm/i915/display/intel_display_types.h
+++ b/drivers/gpu/drm/i915/display/intel_display_types.h
@@ -1460,6 +1460,7 @@ struct intel_dp {
int pcon_max_frl_bw;
u8 max_bpc;
bool ycbcr_444_to_420;
+ bool rgb_to_ycbcr;
} dfp;
/* Display stream compression testing */
diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
index fdc028b7db07..d7e01482c808 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.c
+++ b/drivers/gpu/drm/i915/display/intel_dp.c
@@ -651,6 +651,10 @@ intel_dp_output_format(struct drm_connector *connector,
!drm_mode_is_420_only(info, mode))
return INTEL_OUTPUT_FORMAT_RGB;
+ if (intel_dp->dfp.rgb_to_ycbcr &&
+ intel_dp->dfp.ycbcr_444_to_420)
+ return INTEL_OUTPUT_FORMAT_RGB;
+
if (intel_dp->dfp.ycbcr_444_to_420)
return INTEL_OUTPUT_FORMAT_YCBCR444;
else
@@ -4319,7 +4323,8 @@ static void intel_dp_enable_port(struct intel_dp *intel_dp,
intel_de_posting_read(dev_priv, intel_dp->output_reg);
}
-void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp)
+void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state)
{
struct drm_i915_private *i915 = dp_to_i915(intel_dp);
u8 tmp;
@@ -4348,12 +4353,42 @@ void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp)
enableddisabled(intel_dp->dfp.ycbcr_444_to_420));
tmp = 0;
+ if (intel_dp->dfp.rgb_to_ycbcr) {
+ bool bt2020, bt709;
- if (drm_dp_dpcd_writeb(&intel_dp->aux,
- DP_PROTOCOL_CONVERTER_CONTROL_2, tmp) <= 0)
+ /*
+ * FIXME: Currently if userspace selects BT2020 or BT709, but PCON supports only
+ * RGB->YCbCr for BT601 colorspace, we go ahead with BT601, as default.
+ *
+ */
+ tmp = DP_CONVERSION_BT601_RGB_YCBCR_ENABLE;
+
+ bt2020 = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
+ intel_dp->downstream_ports,
+ DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
+ bt709 = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
+ intel_dp->downstream_ports,
+ DP_DS_HDMI_BT709_RGB_YCBCR_CONV);
+ switch (crtc_state->infoframes.vsc.colorimetry) {
+ case DP_COLORIMETRY_BT2020_RGB:
+ case DP_COLORIMETRY_BT2020_YCC:
+ if (bt2020)
+ tmp = DP_CONVERSION_BT2020_RGB_YCBCR_ENABLE;
+ break;
+ case DP_COLORIMETRY_BT709_YCC:
+ case DP_COLORIMETRY_XVYCC_709:
+ if (bt709)
+ tmp = DP_CONVERSION_BT709_RGB_YCBCR_ENABLE;
+ break;
+ default:
+ break;
+ }
+ }
+
+ if (drm_dp_pcon_convert_rgb_to_ycbcr(&intel_dp->aux, tmp) < 0)
drm_dbg_kms(&i915->drm,
- "Failed to set protocol converter YCbCr 4:2:2 conversion mode to %s\n",
- enableddisabled(false));
+ "Failed to set protocol converter RGB->YCbCr conversion mode to %s\n",
+ enableddisabled(tmp ? true : false));
}
static void intel_enable_dp(struct intel_atomic_state *state,
@@ -4393,7 +4428,7 @@ static void intel_enable_dp(struct intel_atomic_state *state,
}
intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
- intel_dp_configure_protocol_converter(intel_dp);
+ intel_dp_configure_protocol_converter(intel_dp, pipe_config);
intel_dp_check_frl_training(intel_dp);
intel_dp_pcon_dsc_configure(intel_dp, pipe_config);
intel_dp_start_link_train(intel_dp, pipe_config);
@@ -6861,7 +6896,7 @@ intel_dp_update_420(struct intel_dp *intel_dp)
{
struct drm_i915_private *i915 = dp_to_i915(intel_dp);
struct intel_connector *connector = intel_dp->attached_connector;
- bool is_branch, ycbcr_420_passthrough, ycbcr_444_to_420;
+ bool is_branch, ycbcr_420_passthrough, ycbcr_444_to_420, rgb_to_ycbcr;
/* No YCbCr output support on gmch platforms */
if (HAS_GMCH(i915))
@@ -6883,14 +6918,26 @@ intel_dp_update_420(struct intel_dp *intel_dp)
dp_to_dig_port(intel_dp)->lspcon.active ||
drm_dp_downstream_444_to_420_conversion(intel_dp->dpcd,
intel_dp->downstream_ports);
+ rgb_to_ycbcr = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
+ intel_dp->downstream_ports,
+ DP_DS_HDMI_BT601_RGB_YCBCR_CONV ||
+ DP_DS_HDMI_BT709_RGB_YCBCR_CONV ||
+ DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
if (INTEL_GEN(i915) >= 11) {
+ /* Let PCON convert from RGB->YCbCr if possible */
+ if (is_branch && rgb_to_ycbcr && ycbcr_444_to_420) {
+ intel_dp->dfp.rgb_to_ycbcr = true;
+ intel_dp->dfp.ycbcr_444_to_420 = true;
+ connector->base.ycbcr_420_allowed = true;
+ } else {
/* Prefer 4:2:0 passthrough over 4:4:4->4:2:0 conversion */
- intel_dp->dfp.ycbcr_444_to_420 =
- ycbcr_444_to_420 && !ycbcr_420_passthrough;
+ intel_dp->dfp.ycbcr_444_to_420 =
+ ycbcr_444_to_420 && !ycbcr_420_passthrough;
- connector->base.ycbcr_420_allowed =
- !is_branch || ycbcr_444_to_420 || ycbcr_420_passthrough;
+ connector->base.ycbcr_420_allowed =
+ !is_branch || ycbcr_444_to_420 || ycbcr_420_passthrough;
+ }
} else {
/* 4:4:4->4:2:0 conversion is the only way */
intel_dp->dfp.ycbcr_444_to_420 = ycbcr_444_to_420;
@@ -6899,8 +6946,9 @@ intel_dp_update_420(struct intel_dp *intel_dp)
}
drm_dbg_kms(&i915->drm,
- "[CONNECTOR:%d:%s] YCbCr 4:2:0 allowed? %s, YCbCr 4:4:4->4:2:0 conversion? %s\n",
+ "[CONNECTOR:%d:%s] RGB->YcbCr conversion? %s, YCbCr 4:2:0 allowed? %s, YCbCr 4:4:4->4:2:0 conversion? %s\n",
connector->base.base.id, connector->base.name,
+ yesno(intel_dp->dfp.rgb_to_ycbcr),
yesno(connector->base.ycbcr_420_allowed),
yesno(intel_dp->dfp.ycbcr_444_to_420));
}
diff --git a/drivers/gpu/drm/i915/display/intel_dp.h b/drivers/gpu/drm/i915/display/intel_dp.h
index 1bfde4f89019..4280a09fd8fd 100644
--- a/drivers/gpu/drm/i915/display/intel_dp.h
+++ b/drivers/gpu/drm/i915/display/intel_dp.h
@@ -51,7 +51,8 @@ int intel_dp_get_link_train_fallback_values(struct intel_dp *intel_dp,
int intel_dp_retrain_link(struct intel_encoder *encoder,
struct drm_modeset_acquire_ctx *ctx);
void intel_dp_set_power(struct intel_dp *intel_dp, u8 mode);
-void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp);
+void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp,
+ const struct intel_crtc_state *crtc_state);
void intel_dp_sink_set_decompression_state(struct intel_dp *intel_dp,
const struct intel_crtc_state *crtc_state,
bool enable);
--
2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply related [flat|nested] 57+ messages in thread
* RE: [PATCH v7 04/15] drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 11:05 ` Shankar, Uma
-1 siblings, 0 replies; 57+ messages in thread
From: Shankar, Uma @ 2020-12-18 11:05 UTC (permalink / raw)
To: Nautiyal, Ankit K, intel-gfx
Cc: airlied, dri-devel, Sharma, Swati2, Kulkarni, Vandita
> -----Original Message-----
> From: Nautiyal, Ankit K <ankit.k.nautiyal@intel.com>
> Sent: Friday, December 18, 2020 4:07 PM
> To: intel-gfx@lists.freedesktop.org
> Cc: dri-devel@lists.freedesktop.org; Shankar, Uma <uma.shankar@intel.com>;
> airlied@linux.ie; jani.nikula@linux.intel.com; ville.syrjala@linux.intel.com;
> Kulkarni, Vandita <vandita.kulkarni@intel.com>; Sharma, Swati2
> <swati2.sharma@intel.com>
> Subject: [PATCH v7 04/15] drm/dp_helper: Add Helpers for FRL Link Training
> support for DP-HDMI2.1 PCON
>
> This patch adds support for configuring a PCON device, connected as a DP
> branched device to enable FRL Link training with a HDMI2.1 + sink.
>
> v2: Fixed typos and addressed other review comments from Uma Shankar.
> -changed the commit message for better clarity (Uma Shankar) -removed
> unnecessary argument supplied to a drm helper function.
> -fixed return value for max frl read from pcon.
>
> v3: Removed DPCD 0x3035 for MAX Sink FRL b/w as per new version of spec.
>
> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Changes look good, you can keep the RB.
> drivers/gpu/drm/drm_dp_helper.c | 263 ++++++++++++++++++++++++++++++++
> include/drm/drm_dp_helper.h | 70 +++++++++
> 2 files changed, 333 insertions(+)
>
> diff --git a/drivers/gpu/drm/drm_dp_helper.c
> b/drivers/gpu/drm/drm_dp_helper.c index 5bd0934004e3..f501e3890921 100644
> --- a/drivers/gpu/drm/drm_dp_helper.c
> +++ b/drivers/gpu/drm/drm_dp_helper.c
> @@ -2596,3 +2596,266 @@ void drm_dp_vsc_sdp_log(const char *level, struct
> device *dev, #undef DP_SDP_LOG } EXPORT_SYMBOL(drm_dp_vsc_sdp_log);
> +
> +/**
> + * drm_dp_get_pcon_max_frl_bw() - maximum frl supported by PCON
> + * @dpcd: DisplayPort configuration data
> + * @port_cap: port capabilities
> + *
> + * Returns maximum frl bandwidth supported by PCON in GBPS,
> + * returns 0 if not supported.
> + */
> +int drm_dp_get_pcon_max_frl_bw(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
> + const u8 port_cap[4])
> +{
> + int bw;
> + u8 buf;
> +
> + buf = port_cap[2];
> + bw = buf & DP_PCON_MAX_FRL_BW;
> +
> + switch (bw) {
> + case DP_PCON_MAX_9GBPS:
> + return 9;
> + case DP_PCON_MAX_18GBPS:
> + return 18;
> + case DP_PCON_MAX_24GBPS:
> + return 24;
> + case DP_PCON_MAX_32GBPS:
> + return 32;
> + case DP_PCON_MAX_40GBPS:
> + return 40;
> + case DP_PCON_MAX_48GBPS:
> + return 48;
> + case DP_PCON_MAX_0GBPS:
> + default:
> + return 0;
> + }
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(drm_dp_get_pcon_max_frl_bw);
> +
> +/**
> + * drm_dp_pcon_frl_prepare() - Prepare PCON for FRL.
> + * @aux: DisplayPort AUX channel
> + *
> + * Returns 0 if success, else returns negative error code.
> + */
> +int drm_dp_pcon_frl_prepare(struct drm_dp_aux *aux, bool
> +enable_frl_ready_hpd) {
> + int ret;
> + u8 buf = DP_PCON_ENABLE_SOURCE_CTL_MODE |
> + DP_PCON_ENABLE_LINK_FRL_MODE;
> +
> + if (enable_frl_ready_hpd)
> + buf |= DP_PCON_ENABLE_HPD_READY;
> +
> + ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
> +
> + return ret;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_frl_prepare);
> +
> +/**
> + * drm_dp_pcon_is_frl_ready() - Is PCON ready for FRL
> + * @aux: DisplayPort AUX channel
> + *
> + * Returns true if success, else returns false.
> + */
> +bool drm_dp_pcon_is_frl_ready(struct drm_dp_aux *aux) {
> + int ret;
> + u8 buf;
> +
> + ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_TX_LINK_STATUS, &buf);
> + if (ret < 0)
> + return false;
> +
> + if (buf & DP_PCON_FRL_READY)
> + return true;
> +
> + return false;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_is_frl_ready);
> +
> +/**
> + * drm_dp_pcon_frl_configure_1() - Set HDMI LINK Configuration-Step1
> + * @aux: DisplayPort AUX channel
> + * @max_frl_gbps: maximum frl bw to be configured between PCON and HDMI
> +sink
> + * @concurrent_mode: true if concurrent mode or operation is required,
> + * false otherwise.
> + *
> + * Returns 0 if success, else returns negative error code.
> + */
> +
> +int drm_dp_pcon_frl_configure_1(struct drm_dp_aux *aux, int max_frl_gbps,
> + bool concurrent_mode)
> +{
> + int ret;
> + u8 buf;
> +
> + ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf);
> + if (ret < 0)
> + return ret;
> +
> + if (concurrent_mode)
> + buf |= DP_PCON_ENABLE_CONCURRENT_LINK;
> + else
> + buf &= ~DP_PCON_ENABLE_CONCURRENT_LINK;
> +
> + switch (max_frl_gbps) {
> + case 9:
> + buf |= DP_PCON_ENABLE_MAX_BW_9GBPS;
> + break;
> + case 18:
> + buf |= DP_PCON_ENABLE_MAX_BW_18GBPS;
> + break;
> + case 24:
> + buf |= DP_PCON_ENABLE_MAX_BW_24GBPS;
> + break;
> + case 32:
> + buf |= DP_PCON_ENABLE_MAX_BW_32GBPS;
> + break;
> + case 40:
> + buf |= DP_PCON_ENABLE_MAX_BW_40GBPS;
> + break;
> + case 48:
> + buf |= DP_PCON_ENABLE_MAX_BW_48GBPS;
> + break;
> + case 0:
> + buf |= DP_PCON_ENABLE_MAX_BW_0GBPS;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_frl_configure_1);
> +
> +/**
> + * drm_dp_pcon_frl_configure_2() - Set HDMI Link configuration Step-2
> + * @aux: DisplayPort AUX channel
> + * @max_frl_mask : Max FRL BW to be tried by the PCON with HDMI Sink
> + * @extended_train_mode : true for Extended Mode, false for Normal Mode.
> + * In Normal mode, the PCON tries each frl bw from the max_frl_mask
> +starting
> + * from min, and stops when link training is successful. In Extended
> +mode, all
> + * frl bw selected in the mask are trained by the PCON.
> + *
> + * Returns 0 if success, else returns negative error code.
> + */
> +int drm_dp_pcon_frl_configure_2(struct drm_dp_aux *aux, int max_frl_mask,
> + bool extended_train_mode)
> +{
> + int ret;
> + u8 buf = max_frl_mask;
> +
> + if (extended_train_mode)
> + buf |= DP_PCON_FRL_LINK_TRAIN_EXTENDED;
> +
> + ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_2, buf);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_frl_configure_2);
> +
> +/**
> + * drm_dp_pcon_reset_frl_config() - Re-Set HDMI Link configuration.
> + * @aux: DisplayPort AUX channel
> + *
> + * Returns 0 if success, else returns negative error code.
> + */
> +int drm_dp_pcon_reset_frl_config(struct drm_dp_aux *aux) {
> + int ret;
> +
> + ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, 0x0);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_reset_frl_config);
> +
> +/**
> + * drm_dp_pcon_frl_enable() - Enable HDMI link through FRL
> + * @aux: DisplayPort AUX channel
> + *
> + * Returns 0 if success, else returns negative error code.
> + */
> +int drm_dp_pcon_frl_enable(struct drm_dp_aux *aux) {
> + int ret;
> + u8 buf = 0;
> +
> + ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf);
> + if (ret < 0)
> + return ret;
> + if (!(buf & DP_PCON_ENABLE_SOURCE_CTL_MODE)) {
> + DRM_DEBUG_KMS("PCON in Autonomous mode, can't enable
> FRL\n");
> + return -EINVAL;
> + }
> + buf |= DP_PCON_ENABLE_HDMI_LINK;
> + ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_frl_enable);
> +
> +/**
> + * drm_dp_pcon_hdmi_link_active() - check if the PCON HDMI LINK status is
> active.
> + * @aux: DisplayPort AUX channel
> + *
> + * Returns true if link is active else returns false.
> + */
> +bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux) {
> + u8 buf;
> + int ret;
> +
> + ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_TX_LINK_STATUS, &buf);
> + if (ret < 0)
> + return false;
> +
> + return buf & DP_PCON_HDMI_TX_LINK_ACTIVE; }
> +EXPORT_SYMBOL(drm_dp_pcon_hdmi_link_active);
> +
> +/**
> + * drm_dp_pcon_hdmi_link_mode() - get the PCON HDMI LINK MODE
> + * @aux: DisplayPort AUX channel
> + * @frl_trained_mask: pointer to store bitmask of the trained bw configuration.
> + * Valid only if the MODE returned is FRL. For Normal Link training
> +mode
> + * only 1 of the bits will be set, but in case of Extended mode, more
> +than
> + * one bits can be set.
> + *
> + * Returns the link mode : TMDS or FRL on success, else returns
> +negative error
> + * code.
> + */
> +int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8
> +*frl_trained_mask) {
> + u8 buf;
> + int mode;
> + int ret;
> +
> + ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_POST_FRL_STATUS,
> &buf);
> + if (ret < 0)
> + return ret;
> +
> + mode = buf & DP_PCON_HDMI_LINK_MODE;
> +
> + if (frl_trained_mask && DP_PCON_HDMI_MODE_FRL == mode)
> + *frl_trained_mask = (buf & DP_PCON_HDMI_FRL_TRAINED_BW)
> >> 1;
> +
> + return mode;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_hdmi_link_mode);
> diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h index
> 6b40258927bf..c66f570eadc2 100644
> --- a/include/drm/drm_dp_helper.h
> +++ b/include/drm/drm_dp_helper.h
> @@ -411,6 +411,17 @@ struct drm_device;
> # define DP_DS_10BPC 1
> # define DP_DS_12BPC 2
> # define DP_DS_16BPC 3
> +/* HDMI2.1 PCON FRL CONFIGURATION */
> +# define DP_PCON_MAX_FRL_BW (7 << 2)
> +# define DP_PCON_MAX_0GBPS (0 << 2)
> +# define DP_PCON_MAX_9GBPS (1 << 2)
> +# define DP_PCON_MAX_18GBPS (2 << 2)
> +# define DP_PCON_MAX_24GBPS (3 << 2)
> +# define DP_PCON_MAX_32GBPS (4 << 2)
> +# define DP_PCON_MAX_40GBPS (5 << 2)
> +# define DP_PCON_MAX_48GBPS (6 << 2)
> +# define DP_PCON_SOURCE_CTL_MODE (1 << 5)
> +
> /* offset 3 for DVI */
> # define DP_DS_DVI_DUAL_LINK (1 << 1)
> # define DP_DS_DVI_HIGH_COLOR_DEPTH (1 << 2)
> @@ -1054,6 +1065,51 @@ struct drm_device;
> #define DP_CEC_TX_MESSAGE_BUFFER 0x3020
> #define DP_CEC_MESSAGE_BUFFER_LENGTH 0x10
>
> +/* PCON CONFIGURE-1 FRL FOR HDMI SINK */
> +#define DP_PCON_HDMI_LINK_CONFIG_1 0x305A
> +# define DP_PCON_ENABLE_MAX_FRL_BW (7 << 0)
> +# define DP_PCON_ENABLE_MAX_BW_0GBPS 0
> +# define DP_PCON_ENABLE_MAX_BW_9GBPS 1
> +# define DP_PCON_ENABLE_MAX_BW_18GBPS 2
> +# define DP_PCON_ENABLE_MAX_BW_24GBPS 3
> +# define DP_PCON_ENABLE_MAX_BW_32GBPS 4
> +# define DP_PCON_ENABLE_MAX_BW_40GBPS 5
> +# define DP_PCON_ENABLE_MAX_BW_48GBPS 6
> +# define DP_PCON_ENABLE_SOURCE_CTL_MODE (1 << 3)
> +# define DP_PCON_ENABLE_CONCURRENT_LINK (1 << 4)
> +# define DP_PCON_ENABLE_LINK_FRL_MODE (1 << 5)
> +# define DP_PCON_ENABLE_HPD_READY (1 << 6)
> +# define DP_PCON_ENABLE_HDMI_LINK (1 << 7)
> +
> +/* PCON CONFIGURE-2 FRL FOR HDMI SINK */
> +#define DP_PCON_HDMI_LINK_CONFIG_2 0x305B
> +# define DP_PCON_MAX_LINK_BW_MASK (0x3F << 0)
> +# define DP_PCON_FRL_BW_MASK_9GBPS (1 << 0)
> +# define DP_PCON_FRL_BW_MASK_18GBPS (1 << 1)
> +# define DP_PCON_FRL_BW_MASK_24GBPS (1 << 2)
> +# define DP_PCON_FRL_BW_MASK_32GBPS (1 << 3)
> +# define DP_PCON_FRL_BW_MASK_40GBPS (1 << 4)
> +# define DP_PCON_FRL_BW_MASK_48GBPS (1 << 5)
> +# define DP_PCON_FRL_LINK_TRAIN_EXTENDED (1 << 6)
> +
> +/* PCON HDMI LINK STATUS */
> +#define DP_PCON_HDMI_TX_LINK_STATUS 0x303B
> +# define DP_PCON_HDMI_TX_LINK_ACTIVE (1 << 0)
> +# define DP_PCON_FRL_READY (1 << 1)
> +
> +/* PCON HDMI POST FRL STATUS */
> +#define DP_PCON_HDMI_POST_FRL_STATUS 0x3036
> +# define DP_PCON_HDMI_LINK_MODE (1 << 0)
> +# define DP_PCON_HDMI_MODE_TMDS 0
> +# define DP_PCON_HDMI_MODE_FRL 1
> +# define DP_PCON_HDMI_FRL_TRAINED_BW (0x3F << 1)
> +# define DP_PCON_FRL_TRAINED_BW_9GBPS (1 << 1)
> +# define DP_PCON_FRL_TRAINED_BW_18GBPS (1 << 2)
> +# define DP_PCON_FRL_TRAINED_BW_24GBPS (1 << 3)
> +# define DP_PCON_FRL_TRAINED_BW_32GBPS (1 << 4)
> +# define DP_PCON_FRL_TRAINED_BW_40GBPS (1 << 5)
> +# define DP_PCON_FRL_TRAINED_BW_48GBPS (1 << 6)
> +
> #define DP_PROTOCOL_CONVERTER_CONTROL_0 0x3050 /* DP 1.3
> */
> # define DP_HDMI_DVI_OUTPUT_CONFIG (1 << 0) /* DP 1.3 */
> #define DP_PROTOCOL_CONVERTER_CONTROL_1 0x3051 /* DP 1.3
> */
> @@ -1967,4 +2023,18 @@ int drm_dp_get_phy_test_pattern(struct drm_dp_aux
> *aux,
> struct drm_dp_phy_test_params *data); int
> drm_dp_set_phy_test_pattern(struct drm_dp_aux *aux,
> struct drm_dp_phy_test_params *data, u8
> dp_rev);
> +int drm_dp_get_pcon_max_frl_bw(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
> + const u8 port_cap[4]);
> +int drm_dp_pcon_frl_prepare(struct drm_dp_aux *aux, bool
> +enable_frl_ready_hpd); bool drm_dp_pcon_is_frl_ready(struct drm_dp_aux
> +*aux); int drm_dp_pcon_frl_configure_1(struct drm_dp_aux *aux, int
> max_frl_gbps,
> + bool concurrent_mode);
> +int drm_dp_pcon_frl_configure_2(struct drm_dp_aux *aux, int max_frl_mask,
> + bool extended_train_mode);
> +int drm_dp_pcon_reset_frl_config(struct drm_dp_aux *aux); int
> +drm_dp_pcon_frl_enable(struct drm_dp_aux *aux);
> +
> +bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux); int
> +drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8
> +*frl_trained_mask);
> +
> #endif /* _DRM_DP_HELPER_H_ */
> --
> 2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] [PATCH v7 04/15] drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON
@ 2020-12-18 11:05 ` Shankar, Uma
0 siblings, 0 replies; 57+ messages in thread
From: Shankar, Uma @ 2020-12-18 11:05 UTC (permalink / raw)
To: Nautiyal, Ankit K, intel-gfx; +Cc: airlied, dri-devel
> -----Original Message-----
> From: Nautiyal, Ankit K <ankit.k.nautiyal@intel.com>
> Sent: Friday, December 18, 2020 4:07 PM
> To: intel-gfx@lists.freedesktop.org
> Cc: dri-devel@lists.freedesktop.org; Shankar, Uma <uma.shankar@intel.com>;
> airlied@linux.ie; jani.nikula@linux.intel.com; ville.syrjala@linux.intel.com;
> Kulkarni, Vandita <vandita.kulkarni@intel.com>; Sharma, Swati2
> <swati2.sharma@intel.com>
> Subject: [PATCH v7 04/15] drm/dp_helper: Add Helpers for FRL Link Training
> support for DP-HDMI2.1 PCON
>
> This patch adds support for configuring a PCON device, connected as a DP
> branched device to enable FRL Link training with a HDMI2.1 + sink.
>
> v2: Fixed typos and addressed other review comments from Uma Shankar.
> -changed the commit message for better clarity (Uma Shankar) -removed
> unnecessary argument supplied to a drm helper function.
> -fixed return value for max frl read from pcon.
>
> v3: Removed DPCD 0x3035 for MAX Sink FRL b/w as per new version of spec.
>
> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Changes look good, you can keep the RB.
> drivers/gpu/drm/drm_dp_helper.c | 263 ++++++++++++++++++++++++++++++++
> include/drm/drm_dp_helper.h | 70 +++++++++
> 2 files changed, 333 insertions(+)
>
> diff --git a/drivers/gpu/drm/drm_dp_helper.c
> b/drivers/gpu/drm/drm_dp_helper.c index 5bd0934004e3..f501e3890921 100644
> --- a/drivers/gpu/drm/drm_dp_helper.c
> +++ b/drivers/gpu/drm/drm_dp_helper.c
> @@ -2596,3 +2596,266 @@ void drm_dp_vsc_sdp_log(const char *level, struct
> device *dev, #undef DP_SDP_LOG } EXPORT_SYMBOL(drm_dp_vsc_sdp_log);
> +
> +/**
> + * drm_dp_get_pcon_max_frl_bw() - maximum frl supported by PCON
> + * @dpcd: DisplayPort configuration data
> + * @port_cap: port capabilities
> + *
> + * Returns maximum frl bandwidth supported by PCON in GBPS,
> + * returns 0 if not supported.
> + */
> +int drm_dp_get_pcon_max_frl_bw(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
> + const u8 port_cap[4])
> +{
> + int bw;
> + u8 buf;
> +
> + buf = port_cap[2];
> + bw = buf & DP_PCON_MAX_FRL_BW;
> +
> + switch (bw) {
> + case DP_PCON_MAX_9GBPS:
> + return 9;
> + case DP_PCON_MAX_18GBPS:
> + return 18;
> + case DP_PCON_MAX_24GBPS:
> + return 24;
> + case DP_PCON_MAX_32GBPS:
> + return 32;
> + case DP_PCON_MAX_40GBPS:
> + return 40;
> + case DP_PCON_MAX_48GBPS:
> + return 48;
> + case DP_PCON_MAX_0GBPS:
> + default:
> + return 0;
> + }
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(drm_dp_get_pcon_max_frl_bw);
> +
> +/**
> + * drm_dp_pcon_frl_prepare() - Prepare PCON for FRL.
> + * @aux: DisplayPort AUX channel
> + *
> + * Returns 0 if success, else returns negative error code.
> + */
> +int drm_dp_pcon_frl_prepare(struct drm_dp_aux *aux, bool
> +enable_frl_ready_hpd) {
> + int ret;
> + u8 buf = DP_PCON_ENABLE_SOURCE_CTL_MODE |
> + DP_PCON_ENABLE_LINK_FRL_MODE;
> +
> + if (enable_frl_ready_hpd)
> + buf |= DP_PCON_ENABLE_HPD_READY;
> +
> + ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
> +
> + return ret;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_frl_prepare);
> +
> +/**
> + * drm_dp_pcon_is_frl_ready() - Is PCON ready for FRL
> + * @aux: DisplayPort AUX channel
> + *
> + * Returns true if success, else returns false.
> + */
> +bool drm_dp_pcon_is_frl_ready(struct drm_dp_aux *aux) {
> + int ret;
> + u8 buf;
> +
> + ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_TX_LINK_STATUS, &buf);
> + if (ret < 0)
> + return false;
> +
> + if (buf & DP_PCON_FRL_READY)
> + return true;
> +
> + return false;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_is_frl_ready);
> +
> +/**
> + * drm_dp_pcon_frl_configure_1() - Set HDMI LINK Configuration-Step1
> + * @aux: DisplayPort AUX channel
> + * @max_frl_gbps: maximum frl bw to be configured between PCON and HDMI
> +sink
> + * @concurrent_mode: true if concurrent mode or operation is required,
> + * false otherwise.
> + *
> + * Returns 0 if success, else returns negative error code.
> + */
> +
> +int drm_dp_pcon_frl_configure_1(struct drm_dp_aux *aux, int max_frl_gbps,
> + bool concurrent_mode)
> +{
> + int ret;
> + u8 buf;
> +
> + ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf);
> + if (ret < 0)
> + return ret;
> +
> + if (concurrent_mode)
> + buf |= DP_PCON_ENABLE_CONCURRENT_LINK;
> + else
> + buf &= ~DP_PCON_ENABLE_CONCURRENT_LINK;
> +
> + switch (max_frl_gbps) {
> + case 9:
> + buf |= DP_PCON_ENABLE_MAX_BW_9GBPS;
> + break;
> + case 18:
> + buf |= DP_PCON_ENABLE_MAX_BW_18GBPS;
> + break;
> + case 24:
> + buf |= DP_PCON_ENABLE_MAX_BW_24GBPS;
> + break;
> + case 32:
> + buf |= DP_PCON_ENABLE_MAX_BW_32GBPS;
> + break;
> + case 40:
> + buf |= DP_PCON_ENABLE_MAX_BW_40GBPS;
> + break;
> + case 48:
> + buf |= DP_PCON_ENABLE_MAX_BW_48GBPS;
> + break;
> + case 0:
> + buf |= DP_PCON_ENABLE_MAX_BW_0GBPS;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_frl_configure_1);
> +
> +/**
> + * drm_dp_pcon_frl_configure_2() - Set HDMI Link configuration Step-2
> + * @aux: DisplayPort AUX channel
> + * @max_frl_mask : Max FRL BW to be tried by the PCON with HDMI Sink
> + * @extended_train_mode : true for Extended Mode, false for Normal Mode.
> + * In Normal mode, the PCON tries each frl bw from the max_frl_mask
> +starting
> + * from min, and stops when link training is successful. In Extended
> +mode, all
> + * frl bw selected in the mask are trained by the PCON.
> + *
> + * Returns 0 if success, else returns negative error code.
> + */
> +int drm_dp_pcon_frl_configure_2(struct drm_dp_aux *aux, int max_frl_mask,
> + bool extended_train_mode)
> +{
> + int ret;
> + u8 buf = max_frl_mask;
> +
> + if (extended_train_mode)
> + buf |= DP_PCON_FRL_LINK_TRAIN_EXTENDED;
> +
> + ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_2, buf);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_frl_configure_2);
> +
> +/**
> + * drm_dp_pcon_reset_frl_config() - Re-Set HDMI Link configuration.
> + * @aux: DisplayPort AUX channel
> + *
> + * Returns 0 if success, else returns negative error code.
> + */
> +int drm_dp_pcon_reset_frl_config(struct drm_dp_aux *aux) {
> + int ret;
> +
> + ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, 0x0);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_reset_frl_config);
> +
> +/**
> + * drm_dp_pcon_frl_enable() - Enable HDMI link through FRL
> + * @aux: DisplayPort AUX channel
> + *
> + * Returns 0 if success, else returns negative error code.
> + */
> +int drm_dp_pcon_frl_enable(struct drm_dp_aux *aux) {
> + int ret;
> + u8 buf = 0;
> +
> + ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_LINK_CONFIG_1, &buf);
> + if (ret < 0)
> + return ret;
> + if (!(buf & DP_PCON_ENABLE_SOURCE_CTL_MODE)) {
> + DRM_DEBUG_KMS("PCON in Autonomous mode, can't enable
> FRL\n");
> + return -EINVAL;
> + }
> + buf |= DP_PCON_ENABLE_HDMI_LINK;
> + ret = drm_dp_dpcd_writeb(aux, DP_PCON_HDMI_LINK_CONFIG_1, buf);
> + if (ret < 0)
> + return ret;
> +
> + return 0;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_frl_enable);
> +
> +/**
> + * drm_dp_pcon_hdmi_link_active() - check if the PCON HDMI LINK status is
> active.
> + * @aux: DisplayPort AUX channel
> + *
> + * Returns true if link is active else returns false.
> + */
> +bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux) {
> + u8 buf;
> + int ret;
> +
> + ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_TX_LINK_STATUS, &buf);
> + if (ret < 0)
> + return false;
> +
> + return buf & DP_PCON_HDMI_TX_LINK_ACTIVE; }
> +EXPORT_SYMBOL(drm_dp_pcon_hdmi_link_active);
> +
> +/**
> + * drm_dp_pcon_hdmi_link_mode() - get the PCON HDMI LINK MODE
> + * @aux: DisplayPort AUX channel
> + * @frl_trained_mask: pointer to store bitmask of the trained bw configuration.
> + * Valid only if the MODE returned is FRL. For Normal Link training
> +mode
> + * only 1 of the bits will be set, but in case of Extended mode, more
> +than
> + * one bits can be set.
> + *
> + * Returns the link mode : TMDS or FRL on success, else returns
> +negative error
> + * code.
> + */
> +int drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8
> +*frl_trained_mask) {
> + u8 buf;
> + int mode;
> + int ret;
> +
> + ret = drm_dp_dpcd_readb(aux, DP_PCON_HDMI_POST_FRL_STATUS,
> &buf);
> + if (ret < 0)
> + return ret;
> +
> + mode = buf & DP_PCON_HDMI_LINK_MODE;
> +
> + if (frl_trained_mask && DP_PCON_HDMI_MODE_FRL == mode)
> + *frl_trained_mask = (buf & DP_PCON_HDMI_FRL_TRAINED_BW)
> >> 1;
> +
> + return mode;
> +}
> +EXPORT_SYMBOL(drm_dp_pcon_hdmi_link_mode);
> diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h index
> 6b40258927bf..c66f570eadc2 100644
> --- a/include/drm/drm_dp_helper.h
> +++ b/include/drm/drm_dp_helper.h
> @@ -411,6 +411,17 @@ struct drm_device;
> # define DP_DS_10BPC 1
> # define DP_DS_12BPC 2
> # define DP_DS_16BPC 3
> +/* HDMI2.1 PCON FRL CONFIGURATION */
> +# define DP_PCON_MAX_FRL_BW (7 << 2)
> +# define DP_PCON_MAX_0GBPS (0 << 2)
> +# define DP_PCON_MAX_9GBPS (1 << 2)
> +# define DP_PCON_MAX_18GBPS (2 << 2)
> +# define DP_PCON_MAX_24GBPS (3 << 2)
> +# define DP_PCON_MAX_32GBPS (4 << 2)
> +# define DP_PCON_MAX_40GBPS (5 << 2)
> +# define DP_PCON_MAX_48GBPS (6 << 2)
> +# define DP_PCON_SOURCE_CTL_MODE (1 << 5)
> +
> /* offset 3 for DVI */
> # define DP_DS_DVI_DUAL_LINK (1 << 1)
> # define DP_DS_DVI_HIGH_COLOR_DEPTH (1 << 2)
> @@ -1054,6 +1065,51 @@ struct drm_device;
> #define DP_CEC_TX_MESSAGE_BUFFER 0x3020
> #define DP_CEC_MESSAGE_BUFFER_LENGTH 0x10
>
> +/* PCON CONFIGURE-1 FRL FOR HDMI SINK */
> +#define DP_PCON_HDMI_LINK_CONFIG_1 0x305A
> +# define DP_PCON_ENABLE_MAX_FRL_BW (7 << 0)
> +# define DP_PCON_ENABLE_MAX_BW_0GBPS 0
> +# define DP_PCON_ENABLE_MAX_BW_9GBPS 1
> +# define DP_PCON_ENABLE_MAX_BW_18GBPS 2
> +# define DP_PCON_ENABLE_MAX_BW_24GBPS 3
> +# define DP_PCON_ENABLE_MAX_BW_32GBPS 4
> +# define DP_PCON_ENABLE_MAX_BW_40GBPS 5
> +# define DP_PCON_ENABLE_MAX_BW_48GBPS 6
> +# define DP_PCON_ENABLE_SOURCE_CTL_MODE (1 << 3)
> +# define DP_PCON_ENABLE_CONCURRENT_LINK (1 << 4)
> +# define DP_PCON_ENABLE_LINK_FRL_MODE (1 << 5)
> +# define DP_PCON_ENABLE_HPD_READY (1 << 6)
> +# define DP_PCON_ENABLE_HDMI_LINK (1 << 7)
> +
> +/* PCON CONFIGURE-2 FRL FOR HDMI SINK */
> +#define DP_PCON_HDMI_LINK_CONFIG_2 0x305B
> +# define DP_PCON_MAX_LINK_BW_MASK (0x3F << 0)
> +# define DP_PCON_FRL_BW_MASK_9GBPS (1 << 0)
> +# define DP_PCON_FRL_BW_MASK_18GBPS (1 << 1)
> +# define DP_PCON_FRL_BW_MASK_24GBPS (1 << 2)
> +# define DP_PCON_FRL_BW_MASK_32GBPS (1 << 3)
> +# define DP_PCON_FRL_BW_MASK_40GBPS (1 << 4)
> +# define DP_PCON_FRL_BW_MASK_48GBPS (1 << 5)
> +# define DP_PCON_FRL_LINK_TRAIN_EXTENDED (1 << 6)
> +
> +/* PCON HDMI LINK STATUS */
> +#define DP_PCON_HDMI_TX_LINK_STATUS 0x303B
> +# define DP_PCON_HDMI_TX_LINK_ACTIVE (1 << 0)
> +# define DP_PCON_FRL_READY (1 << 1)
> +
> +/* PCON HDMI POST FRL STATUS */
> +#define DP_PCON_HDMI_POST_FRL_STATUS 0x3036
> +# define DP_PCON_HDMI_LINK_MODE (1 << 0)
> +# define DP_PCON_HDMI_MODE_TMDS 0
> +# define DP_PCON_HDMI_MODE_FRL 1
> +# define DP_PCON_HDMI_FRL_TRAINED_BW (0x3F << 1)
> +# define DP_PCON_FRL_TRAINED_BW_9GBPS (1 << 1)
> +# define DP_PCON_FRL_TRAINED_BW_18GBPS (1 << 2)
> +# define DP_PCON_FRL_TRAINED_BW_24GBPS (1 << 3)
> +# define DP_PCON_FRL_TRAINED_BW_32GBPS (1 << 4)
> +# define DP_PCON_FRL_TRAINED_BW_40GBPS (1 << 5)
> +# define DP_PCON_FRL_TRAINED_BW_48GBPS (1 << 6)
> +
> #define DP_PROTOCOL_CONVERTER_CONTROL_0 0x3050 /* DP 1.3
> */
> # define DP_HDMI_DVI_OUTPUT_CONFIG (1 << 0) /* DP 1.3 */
> #define DP_PROTOCOL_CONVERTER_CONTROL_1 0x3051 /* DP 1.3
> */
> @@ -1967,4 +2023,18 @@ int drm_dp_get_phy_test_pattern(struct drm_dp_aux
> *aux,
> struct drm_dp_phy_test_params *data); int
> drm_dp_set_phy_test_pattern(struct drm_dp_aux *aux,
> struct drm_dp_phy_test_params *data, u8
> dp_rev);
> +int drm_dp_get_pcon_max_frl_bw(const u8 dpcd[DP_RECEIVER_CAP_SIZE],
> + const u8 port_cap[4]);
> +int drm_dp_pcon_frl_prepare(struct drm_dp_aux *aux, bool
> +enable_frl_ready_hpd); bool drm_dp_pcon_is_frl_ready(struct drm_dp_aux
> +*aux); int drm_dp_pcon_frl_configure_1(struct drm_dp_aux *aux, int
> max_frl_gbps,
> + bool concurrent_mode);
> +int drm_dp_pcon_frl_configure_2(struct drm_dp_aux *aux, int max_frl_mask,
> + bool extended_train_mode);
> +int drm_dp_pcon_reset_frl_config(struct drm_dp_aux *aux); int
> +drm_dp_pcon_frl_enable(struct drm_dp_aux *aux);
> +
> +bool drm_dp_pcon_hdmi_link_active(struct drm_dp_aux *aux); int
> +drm_dp_pcon_hdmi_link_mode(struct drm_dp_aux *aux, u8
> +*frl_trained_mask);
> +
> #endif /* _DRM_DP_HELPER_H_ */
> --
> 2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* RE: [PATCH v7 11/15] drm/i915: Add support for enabling link status and recovery
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 11:06 ` Shankar, Uma
-1 siblings, 0 replies; 57+ messages in thread
From: Shankar, Uma @ 2020-12-18 11:06 UTC (permalink / raw)
To: Nautiyal, Ankit K, intel-gfx
Cc: airlied, dri-devel, Sharma, Swati2, Kulkarni, Vandita
> -----Original Message-----
> From: Nautiyal, Ankit K <ankit.k.nautiyal@intel.com>
> Sent: Friday, December 18, 2020 4:07 PM
> To: intel-gfx@lists.freedesktop.org
> Cc: dri-devel@lists.freedesktop.org; Shankar, Uma <uma.shankar@intel.com>;
> airlied@linux.ie; jani.nikula@linux.intel.com; ville.syrjala@linux.intel.com;
> Kulkarni, Vandita <vandita.kulkarni@intel.com>; Sharma, Swati2
> <swati2.sharma@intel.com>
> Subject: [PATCH v7 11/15] drm/i915: Add support for enabling link status and
> recovery
>
> From: Swati Sharma <swati2.sharma@intel.com>
>
> In this patch enables support for detecting link failures between PCON and HDMI
> sink in i915 driver. HDMI link loss indication to upstream DP source is indicated
> via IRQ_HPD. This is followed by reading of HDMI link configuration status
> (HDMI_TX_LINK_ACTIVE_STATUS).
> If the PCON → HDMI 2.1 link status is off; reinitiate frl link training to recover.
> Also, report HDMI FRL link error count range for each individual FRL active lane is
> indicated by DOWNSTREAM_HDMI_ERROR_STATUS_LN registers.
>
> v2: Checked for dpcd read and write failures and added debug message.
> (Uma Shankar)
>
> v3: Rearranged code to re-start FRL link training or fall back to TMDS mode.
>
> v4: Resused function to check frl which inturn restarts FRL and fallback to TMDS
> mode.
>
> Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Change looks fine, you can keep RB.
> ---
> drivers/gpu/drm/i915/display/intel_dp.c | 53 +++++++++++++++++++++++--
> 1 file changed, 50 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c
> b/drivers/gpu/drm/i915/display/intel_dp.c
> index 1e0ff39bb927..66f35e7c9903 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> @@ -6013,6 +6013,28 @@ intel_dp_check_mst_status(struct intel_dp *intel_dp)
> return link_ok;
> }
>
> +static void
> +intel_dp_handle_hdmi_link_status_change(struct intel_dp *intel_dp) {
> + bool is_active;
> + u8 buf = 0;
> +
> + is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux);
> + if (intel_dp->frl.is_trained && !is_active) {
> + if (drm_dp_dpcd_readb(&intel_dp->aux,
> DP_PCON_HDMI_LINK_CONFIG_1, &buf) < 0)
> + return;
> +
> + buf &= ~DP_PCON_ENABLE_HDMI_LINK;
> + if (drm_dp_dpcd_writeb(&intel_dp->aux,
> DP_PCON_HDMI_LINK_CONFIG_1, buf) < 0)
> + return;
> +
> + drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux,
> +&intel_dp->attached_connector->base);
> +
> + /* Restart FRL training or fall back to TMDS mode */
> + intel_dp_check_frl_training(intel_dp);
> + }
> +}
> +
> static bool
> intel_dp_needs_link_retrain(struct intel_dp *intel_dp) { @@ -6378,7 +6400,7
> @@ intel_dp_hotplug(struct intel_encoder *encoder,
> return state;
> }
>
> -static void intel_dp_check_service_irq(struct intel_dp *intel_dp)
> +static void intel_dp_check_device_service_irq(struct intel_dp
> +*intel_dp)
> {
> struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> u8 val;
> @@ -6402,6 +6424,30 @@ static void intel_dp_check_service_irq(struct intel_dp
> *intel_dp)
> drm_dbg_kms(&i915->drm, "Sink specific irq unhandled\n"); }
>
> +static void intel_dp_check_link_service_irq(struct intel_dp *intel_dp)
> +{
> + struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> + u8 val;
> +
> + if (intel_dp->dpcd[DP_DPCD_REV] < 0x11)
> + return;
> +
> + if (drm_dp_dpcd_readb(&intel_dp->aux,
> + DP_LINK_SERVICE_IRQ_VECTOR_ESI0, &val) != 1 ||
> !val) {
> + drm_dbg_kms(&i915->drm, "Error in reading link service irq
> vector\n");
> + return;
> + }
> +
> + if (drm_dp_dpcd_writeb(&intel_dp->aux,
> + DP_LINK_SERVICE_IRQ_VECTOR_ESI0, val) != 1) {
> + drm_dbg_kms(&i915->drm, "Error in writing link service irq
> vector\n");
> + return;
> + }
> +
> + if (val & HDMI_LINK_STATUS_CHANGED)
> + intel_dp_handle_hdmi_link_status_change(intel_dp);
> +}
> +
> /*
> * According to DP spec
> * 5.1.2:
> @@ -6441,7 +6487,8 @@ intel_dp_short_pulse(struct intel_dp *intel_dp)
> return false;
> }
>
> - intel_dp_check_service_irq(intel_dp);
> + intel_dp_check_device_service_irq(intel_dp);
> + intel_dp_check_link_service_irq(intel_dp);
>
> /* Handle CEC interrupts, if any */
> drm_dp_cec_irq(&intel_dp->aux);
> @@ -6871,7 +6918,7 @@ intel_dp_detect(struct drm_connector *connector,
> to_intel_connector(connector)->detect_edid)
> status = connector_status_connected;
>
> - intel_dp_check_service_irq(intel_dp);
> + intel_dp_check_device_service_irq(intel_dp);
>
> out:
> if (status != connector_status_connected && !intel_dp->is_mst)
> --
> 2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] [PATCH v7 11/15] drm/i915: Add support for enabling link status and recovery
@ 2020-12-18 11:06 ` Shankar, Uma
0 siblings, 0 replies; 57+ messages in thread
From: Shankar, Uma @ 2020-12-18 11:06 UTC (permalink / raw)
To: Nautiyal, Ankit K, intel-gfx; +Cc: airlied, dri-devel
> -----Original Message-----
> From: Nautiyal, Ankit K <ankit.k.nautiyal@intel.com>
> Sent: Friday, December 18, 2020 4:07 PM
> To: intel-gfx@lists.freedesktop.org
> Cc: dri-devel@lists.freedesktop.org; Shankar, Uma <uma.shankar@intel.com>;
> airlied@linux.ie; jani.nikula@linux.intel.com; ville.syrjala@linux.intel.com;
> Kulkarni, Vandita <vandita.kulkarni@intel.com>; Sharma, Swati2
> <swati2.sharma@intel.com>
> Subject: [PATCH v7 11/15] drm/i915: Add support for enabling link status and
> recovery
>
> From: Swati Sharma <swati2.sharma@intel.com>
>
> In this patch enables support for detecting link failures between PCON and HDMI
> sink in i915 driver. HDMI link loss indication to upstream DP source is indicated
> via IRQ_HPD. This is followed by reading of HDMI link configuration status
> (HDMI_TX_LINK_ACTIVE_STATUS).
> If the PCON → HDMI 2.1 link status is off; reinitiate frl link training to recover.
> Also, report HDMI FRL link error count range for each individual FRL active lane is
> indicated by DOWNSTREAM_HDMI_ERROR_STATUS_LN registers.
>
> v2: Checked for dpcd read and write failures and added debug message.
> (Uma Shankar)
>
> v3: Rearranged code to re-start FRL link training or fall back to TMDS mode.
>
> v4: Resused function to check frl which inturn restarts FRL and fallback to TMDS
> mode.
>
> Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Change looks fine, you can keep RB.
> ---
> drivers/gpu/drm/i915/display/intel_dp.c | 53 +++++++++++++++++++++++--
> 1 file changed, 50 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c
> b/drivers/gpu/drm/i915/display/intel_dp.c
> index 1e0ff39bb927..66f35e7c9903 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> @@ -6013,6 +6013,28 @@ intel_dp_check_mst_status(struct intel_dp *intel_dp)
> return link_ok;
> }
>
> +static void
> +intel_dp_handle_hdmi_link_status_change(struct intel_dp *intel_dp) {
> + bool is_active;
> + u8 buf = 0;
> +
> + is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux);
> + if (intel_dp->frl.is_trained && !is_active) {
> + if (drm_dp_dpcd_readb(&intel_dp->aux,
> DP_PCON_HDMI_LINK_CONFIG_1, &buf) < 0)
> + return;
> +
> + buf &= ~DP_PCON_ENABLE_HDMI_LINK;
> + if (drm_dp_dpcd_writeb(&intel_dp->aux,
> DP_PCON_HDMI_LINK_CONFIG_1, buf) < 0)
> + return;
> +
> + drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux,
> +&intel_dp->attached_connector->base);
> +
> + /* Restart FRL training or fall back to TMDS mode */
> + intel_dp_check_frl_training(intel_dp);
> + }
> +}
> +
> static bool
> intel_dp_needs_link_retrain(struct intel_dp *intel_dp) { @@ -6378,7 +6400,7
> @@ intel_dp_hotplug(struct intel_encoder *encoder,
> return state;
> }
>
> -static void intel_dp_check_service_irq(struct intel_dp *intel_dp)
> +static void intel_dp_check_device_service_irq(struct intel_dp
> +*intel_dp)
> {
> struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> u8 val;
> @@ -6402,6 +6424,30 @@ static void intel_dp_check_service_irq(struct intel_dp
> *intel_dp)
> drm_dbg_kms(&i915->drm, "Sink specific irq unhandled\n"); }
>
> +static void intel_dp_check_link_service_irq(struct intel_dp *intel_dp)
> +{
> + struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> + u8 val;
> +
> + if (intel_dp->dpcd[DP_DPCD_REV] < 0x11)
> + return;
> +
> + if (drm_dp_dpcd_readb(&intel_dp->aux,
> + DP_LINK_SERVICE_IRQ_VECTOR_ESI0, &val) != 1 ||
> !val) {
> + drm_dbg_kms(&i915->drm, "Error in reading link service irq
> vector\n");
> + return;
> + }
> +
> + if (drm_dp_dpcd_writeb(&intel_dp->aux,
> + DP_LINK_SERVICE_IRQ_VECTOR_ESI0, val) != 1) {
> + drm_dbg_kms(&i915->drm, "Error in writing link service irq
> vector\n");
> + return;
> + }
> +
> + if (val & HDMI_LINK_STATUS_CHANGED)
> + intel_dp_handle_hdmi_link_status_change(intel_dp);
> +}
> +
> /*
> * According to DP spec
> * 5.1.2:
> @@ -6441,7 +6487,8 @@ intel_dp_short_pulse(struct intel_dp *intel_dp)
> return false;
> }
>
> - intel_dp_check_service_irq(intel_dp);
> + intel_dp_check_device_service_irq(intel_dp);
> + intel_dp_check_link_service_irq(intel_dp);
>
> /* Handle CEC interrupts, if any */
> drm_dp_cec_irq(&intel_dp->aux);
> @@ -6871,7 +6918,7 @@ intel_dp_detect(struct drm_connector *connector,
> to_intel_connector(connector)->detect_edid)
> status = connector_status_connected;
>
> - intel_dp_check_service_irq(intel_dp);
> + intel_dp_check_device_service_irq(intel_dp);
>
> out:
> if (status != connector_status_connected && !intel_dp->is_mst)
> --
> 2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* RE: [PATCH v7 15/15] drm/i915/display: Let PCON convert from RGB to YCbCr if it can
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-18 11:11 ` Shankar, Uma
-1 siblings, 0 replies; 57+ messages in thread
From: Shankar, Uma @ 2020-12-18 11:11 UTC (permalink / raw)
To: Nautiyal, Ankit K, intel-gfx
Cc: airlied, dri-devel, Sharma, Swati2, Kulkarni, Vandita
> -----Original Message-----
> From: Nautiyal, Ankit K <ankit.k.nautiyal@intel.com>
> Sent: Friday, December 18, 2020 4:07 PM
> To: intel-gfx@lists.freedesktop.org
> Cc: dri-devel@lists.freedesktop.org; Shankar, Uma <uma.shankar@intel.com>;
> airlied@linux.ie; jani.nikula@linux.intel.com; ville.syrjala@linux.intel.com;
> Kulkarni, Vandita <vandita.kulkarni@intel.com>; Sharma, Swati2
> <swati2.sharma@intel.com>
> Subject: [PATCH v7 15/15] drm/i915/display: Let PCON convert from RGB to
> YCbCr if it can
>
> If PCON has capability to convert RGB->YCbCr colorspace and also to 444->420
> downsampling then for any YUV420 only mode, we can let the PCON do all the
> conversion. If the PCON supports
> RGB->YCbCr conversion for all BT2020, BT709, BT601, choose
> the one that is selected by userspace via connector colorspace property,
> otherwise default to BT601.
>
> v2: As suggested by Uma Shankar, considered case for colorspace
> BT709 and BT2020, and default to BT601. Also appended dir 'display' in commit
> message.
>
> v3: Fixed typo in condition for printing one of the error msg.
>
> v4: As suggested by Uma Shankar:
> -Fixed bug in determining the colorspace for RGB->YCbCr conversion.
> -Fixed minor formatting issues
> Also updated the commit message as per latest changes.
Changes look good, please work on color fixup as a separate series.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
> ---
> drivers/gpu/drm/i915/display/intel_ddi.c | 3 +-
> .../drm/i915/display/intel_display_types.h | 1 +
> drivers/gpu/drm/i915/display/intel_dp.c | 72 +++++++++++++++----
> drivers/gpu/drm/i915/display/intel_dp.h | 3 +-
> 4 files changed, 65 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c
> b/drivers/gpu/drm/i915/display/intel_ddi.c
> index fbc07a93504b..17eaa56c5a99 100644
> --- a/drivers/gpu/drm/i915/display/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/display/intel_ddi.c
> @@ -3644,6 +3644,7 @@ static void tgl_ddi_pre_enable_dp(struct
> intel_atomic_state *state,
> if (!is_mst)
> intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
>
> + intel_dp_configure_protocol_converter(intel_dp, crtc_state);
> intel_dp_sink_set_decompression_state(intel_dp, crtc_state, true);
> /*
> * DDI FEC: "anticipates enabling FEC encoding sets the FEC_READY bit
> @@ -3731,7 +3732,7 @@ static void hsw_ddi_pre_enable_dp(struct
> intel_atomic_state *state,
> intel_ddi_init_dp_buf_reg(encoder, crtc_state);
> if (!is_mst)
> intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
> - intel_dp_configure_protocol_converter(intel_dp);
> + intel_dp_configure_protocol_converter(intel_dp, crtc_state);
> intel_dp_sink_set_decompression_state(intel_dp, crtc_state,
> true);
> intel_dp_sink_set_fec_ready(intel_dp, crtc_state); diff --git
> a/drivers/gpu/drm/i915/display/intel_display_types.h
> b/drivers/gpu/drm/i915/display/intel_display_types.h
> index 4c01c7c23dfd..2009ae9e9678 100644
> --- a/drivers/gpu/drm/i915/display/intel_display_types.h
> +++ b/drivers/gpu/drm/i915/display/intel_display_types.h
> @@ -1460,6 +1460,7 @@ struct intel_dp {
> int pcon_max_frl_bw;
> u8 max_bpc;
> bool ycbcr_444_to_420;
> + bool rgb_to_ycbcr;
> } dfp;
>
> /* Display stream compression testing */ diff --git
> a/drivers/gpu/drm/i915/display/intel_dp.c
> b/drivers/gpu/drm/i915/display/intel_dp.c
> index fdc028b7db07..d7e01482c808 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> @@ -651,6 +651,10 @@ intel_dp_output_format(struct drm_connector
> *connector,
> !drm_mode_is_420_only(info, mode))
> return INTEL_OUTPUT_FORMAT_RGB;
>
> + if (intel_dp->dfp.rgb_to_ycbcr &&
> + intel_dp->dfp.ycbcr_444_to_420)
> + return INTEL_OUTPUT_FORMAT_RGB;
> +
> if (intel_dp->dfp.ycbcr_444_to_420)
> return INTEL_OUTPUT_FORMAT_YCBCR444;
> else
> @@ -4319,7 +4323,8 @@ static void intel_dp_enable_port(struct intel_dp
> *intel_dp,
> intel_de_posting_read(dev_priv, intel_dp->output_reg); }
>
> -void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp)
> +void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp,
> + const struct intel_crtc_state *crtc_state)
> {
> struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> u8 tmp;
> @@ -4348,12 +4353,42 @@ void intel_dp_configure_protocol_converter(struct
> intel_dp *intel_dp)
> enableddisabled(intel_dp->dfp.ycbcr_444_to_420));
>
> tmp = 0;
> + if (intel_dp->dfp.rgb_to_ycbcr) {
> + bool bt2020, bt709;
>
> - if (drm_dp_dpcd_writeb(&intel_dp->aux,
> - DP_PROTOCOL_CONVERTER_CONTROL_2, tmp) <= 0)
> + /*
> + * FIXME: Currently if userspace selects BT2020 or BT709, but
> PCON supports only
> + * RGB->YCbCr for BT601 colorspace, we go ahead with BT601, as
> default.
> + *
> + */
> + tmp = DP_CONVERSION_BT601_RGB_YCBCR_ENABLE;
> +
> + bt2020 =
> drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
> + intel_dp-
> >downstream_ports,
> +
> DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
> + bt709 =
> drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
> + intel_dp-
> >downstream_ports,
> +
> DP_DS_HDMI_BT709_RGB_YCBCR_CONV);
> + switch (crtc_state->infoframes.vsc.colorimetry) {
> + case DP_COLORIMETRY_BT2020_RGB:
> + case DP_COLORIMETRY_BT2020_YCC:
> + if (bt2020)
> + tmp =
> DP_CONVERSION_BT2020_RGB_YCBCR_ENABLE;
> + break;
> + case DP_COLORIMETRY_BT709_YCC:
> + case DP_COLORIMETRY_XVYCC_709:
> + if (bt709)
> + tmp =
> DP_CONVERSION_BT709_RGB_YCBCR_ENABLE;
> + break;
> + default:
> + break;
> + }
> + }
> +
> + if (drm_dp_pcon_convert_rgb_to_ycbcr(&intel_dp->aux, tmp) < 0)
> drm_dbg_kms(&i915->drm,
> - "Failed to set protocol converter YCbCr 4:2:2
> conversion mode to %s\n",
> - enableddisabled(false));
> + "Failed to set protocol converter RGB->YCbCr
> conversion mode to %s\n",
> + enableddisabled(tmp ? true : false));
> }
>
> static void intel_enable_dp(struct intel_atomic_state *state, @@ -4393,7
> +4428,7 @@ static void intel_enable_dp(struct intel_atomic_state *state,
> }
>
> intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
> - intel_dp_configure_protocol_converter(intel_dp);
> + intel_dp_configure_protocol_converter(intel_dp, pipe_config);
> intel_dp_check_frl_training(intel_dp);
> intel_dp_pcon_dsc_configure(intel_dp, pipe_config);
> intel_dp_start_link_train(intel_dp, pipe_config); @@ -6861,7 +6896,7
> @@ intel_dp_update_420(struct intel_dp *intel_dp) {
> struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> struct intel_connector *connector = intel_dp->attached_connector;
> - bool is_branch, ycbcr_420_passthrough, ycbcr_444_to_420;
> + bool is_branch, ycbcr_420_passthrough, ycbcr_444_to_420, rgb_to_ycbcr;
>
> /* No YCbCr output support on gmch platforms */
> if (HAS_GMCH(i915))
> @@ -6883,14 +6918,26 @@ intel_dp_update_420(struct intel_dp *intel_dp)
> dp_to_dig_port(intel_dp)->lspcon.active ||
> drm_dp_downstream_444_to_420_conversion(intel_dp->dpcd,
> intel_dp-
> >downstream_ports);
> + rgb_to_ycbcr = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp-
> >dpcd,
> + intel_dp-
> >downstream_ports,
> +
> DP_DS_HDMI_BT601_RGB_YCBCR_CONV ||
> +
> DP_DS_HDMI_BT709_RGB_YCBCR_CONV ||
> +
> DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
>
> if (INTEL_GEN(i915) >= 11) {
> + /* Let PCON convert from RGB->YCbCr if possible */
> + if (is_branch && rgb_to_ycbcr && ycbcr_444_to_420) {
> + intel_dp->dfp.rgb_to_ycbcr = true;
> + intel_dp->dfp.ycbcr_444_to_420 = true;
> + connector->base.ycbcr_420_allowed = true;
> + } else {
> /* Prefer 4:2:0 passthrough over 4:4:4->4:2:0 conversion */
> - intel_dp->dfp.ycbcr_444_to_420 =
> - ycbcr_444_to_420 && !ycbcr_420_passthrough;
> + intel_dp->dfp.ycbcr_444_to_420 =
> + ycbcr_444_to_420 && !ycbcr_420_passthrough;
>
> - connector->base.ycbcr_420_allowed =
> - !is_branch || ycbcr_444_to_420 ||
> ycbcr_420_passthrough;
> + connector->base.ycbcr_420_allowed =
> + !is_branch || ycbcr_444_to_420 ||
> ycbcr_420_passthrough;
> + }
> } else {
> /* 4:4:4->4:2:0 conversion is the only way */
> intel_dp->dfp.ycbcr_444_to_420 = ycbcr_444_to_420; @@ -
> 6899,8 +6946,9 @@ intel_dp_update_420(struct intel_dp *intel_dp)
> }
>
> drm_dbg_kms(&i915->drm,
> - "[CONNECTOR:%d:%s] YCbCr 4:2:0 allowed? %s, YCbCr 4:4:4-
> >4:2:0 conversion? %s\n",
> + "[CONNECTOR:%d:%s] RGB->YcbCr conversion? %s, YCbCr 4:2:0
> +allowed? %s, YCbCr 4:4:4->4:2:0 conversion? %s\n",
> connector->base.base.id, connector->base.name,
> + yesno(intel_dp->dfp.rgb_to_ycbcr),
> yesno(connector->base.ycbcr_420_allowed),
> yesno(intel_dp->dfp.ycbcr_444_to_420));
> }
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.h
> b/drivers/gpu/drm/i915/display/intel_dp.h
> index 1bfde4f89019..4280a09fd8fd 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.h
> +++ b/drivers/gpu/drm/i915/display/intel_dp.h
> @@ -51,7 +51,8 @@ int intel_dp_get_link_train_fallback_values(struct intel_dp
> *intel_dp, int intel_dp_retrain_link(struct intel_encoder *encoder,
> struct drm_modeset_acquire_ctx *ctx); void
> intel_dp_set_power(struct intel_dp *intel_dp, u8 mode); -void
> intel_dp_configure_protocol_converter(struct intel_dp *intel_dp);
> +void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp,
> + const struct intel_crtc_state
> *crtc_state);
> void intel_dp_sink_set_decompression_state(struct intel_dp *intel_dp,
> const struct intel_crtc_state *crtc_state,
> bool enable);
> --
> 2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] [PATCH v7 15/15] drm/i915/display: Let PCON convert from RGB to YCbCr if it can
@ 2020-12-18 11:11 ` Shankar, Uma
0 siblings, 0 replies; 57+ messages in thread
From: Shankar, Uma @ 2020-12-18 11:11 UTC (permalink / raw)
To: Nautiyal, Ankit K, intel-gfx; +Cc: airlied, dri-devel
> -----Original Message-----
> From: Nautiyal, Ankit K <ankit.k.nautiyal@intel.com>
> Sent: Friday, December 18, 2020 4:07 PM
> To: intel-gfx@lists.freedesktop.org
> Cc: dri-devel@lists.freedesktop.org; Shankar, Uma <uma.shankar@intel.com>;
> airlied@linux.ie; jani.nikula@linux.intel.com; ville.syrjala@linux.intel.com;
> Kulkarni, Vandita <vandita.kulkarni@intel.com>; Sharma, Swati2
> <swati2.sharma@intel.com>
> Subject: [PATCH v7 15/15] drm/i915/display: Let PCON convert from RGB to
> YCbCr if it can
>
> If PCON has capability to convert RGB->YCbCr colorspace and also to 444->420
> downsampling then for any YUV420 only mode, we can let the PCON do all the
> conversion. If the PCON supports
> RGB->YCbCr conversion for all BT2020, BT709, BT601, choose
> the one that is selected by userspace via connector colorspace property,
> otherwise default to BT601.
>
> v2: As suggested by Uma Shankar, considered case for colorspace
> BT709 and BT2020, and default to BT601. Also appended dir 'display' in commit
> message.
>
> v3: Fixed typo in condition for printing one of the error msg.
>
> v4: As suggested by Uma Shankar:
> -Fixed bug in determining the colorspace for RGB->YCbCr conversion.
> -Fixed minor formatting issues
> Also updated the commit message as per latest changes.
Changes look good, please work on color fixup as a separate series.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
> ---
> drivers/gpu/drm/i915/display/intel_ddi.c | 3 +-
> .../drm/i915/display/intel_display_types.h | 1 +
> drivers/gpu/drm/i915/display/intel_dp.c | 72 +++++++++++++++----
> drivers/gpu/drm/i915/display/intel_dp.h | 3 +-
> 4 files changed, 65 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c
> b/drivers/gpu/drm/i915/display/intel_ddi.c
> index fbc07a93504b..17eaa56c5a99 100644
> --- a/drivers/gpu/drm/i915/display/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/display/intel_ddi.c
> @@ -3644,6 +3644,7 @@ static void tgl_ddi_pre_enable_dp(struct
> intel_atomic_state *state,
> if (!is_mst)
> intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
>
> + intel_dp_configure_protocol_converter(intel_dp, crtc_state);
> intel_dp_sink_set_decompression_state(intel_dp, crtc_state, true);
> /*
> * DDI FEC: "anticipates enabling FEC encoding sets the FEC_READY bit
> @@ -3731,7 +3732,7 @@ static void hsw_ddi_pre_enable_dp(struct
> intel_atomic_state *state,
> intel_ddi_init_dp_buf_reg(encoder, crtc_state);
> if (!is_mst)
> intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
> - intel_dp_configure_protocol_converter(intel_dp);
> + intel_dp_configure_protocol_converter(intel_dp, crtc_state);
> intel_dp_sink_set_decompression_state(intel_dp, crtc_state,
> true);
> intel_dp_sink_set_fec_ready(intel_dp, crtc_state); diff --git
> a/drivers/gpu/drm/i915/display/intel_display_types.h
> b/drivers/gpu/drm/i915/display/intel_display_types.h
> index 4c01c7c23dfd..2009ae9e9678 100644
> --- a/drivers/gpu/drm/i915/display/intel_display_types.h
> +++ b/drivers/gpu/drm/i915/display/intel_display_types.h
> @@ -1460,6 +1460,7 @@ struct intel_dp {
> int pcon_max_frl_bw;
> u8 max_bpc;
> bool ycbcr_444_to_420;
> + bool rgb_to_ycbcr;
> } dfp;
>
> /* Display stream compression testing */ diff --git
> a/drivers/gpu/drm/i915/display/intel_dp.c
> b/drivers/gpu/drm/i915/display/intel_dp.c
> index fdc028b7db07..d7e01482c808 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> @@ -651,6 +651,10 @@ intel_dp_output_format(struct drm_connector
> *connector,
> !drm_mode_is_420_only(info, mode))
> return INTEL_OUTPUT_FORMAT_RGB;
>
> + if (intel_dp->dfp.rgb_to_ycbcr &&
> + intel_dp->dfp.ycbcr_444_to_420)
> + return INTEL_OUTPUT_FORMAT_RGB;
> +
> if (intel_dp->dfp.ycbcr_444_to_420)
> return INTEL_OUTPUT_FORMAT_YCBCR444;
> else
> @@ -4319,7 +4323,8 @@ static void intel_dp_enable_port(struct intel_dp
> *intel_dp,
> intel_de_posting_read(dev_priv, intel_dp->output_reg); }
>
> -void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp)
> +void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp,
> + const struct intel_crtc_state *crtc_state)
> {
> struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> u8 tmp;
> @@ -4348,12 +4353,42 @@ void intel_dp_configure_protocol_converter(struct
> intel_dp *intel_dp)
> enableddisabled(intel_dp->dfp.ycbcr_444_to_420));
>
> tmp = 0;
> + if (intel_dp->dfp.rgb_to_ycbcr) {
> + bool bt2020, bt709;
>
> - if (drm_dp_dpcd_writeb(&intel_dp->aux,
> - DP_PROTOCOL_CONVERTER_CONTROL_2, tmp) <= 0)
> + /*
> + * FIXME: Currently if userspace selects BT2020 or BT709, but
> PCON supports only
> + * RGB->YCbCr for BT601 colorspace, we go ahead with BT601, as
> default.
> + *
> + */
> + tmp = DP_CONVERSION_BT601_RGB_YCBCR_ENABLE;
> +
> + bt2020 =
> drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
> + intel_dp-
> >downstream_ports,
> +
> DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
> + bt709 =
> drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
> + intel_dp-
> >downstream_ports,
> +
> DP_DS_HDMI_BT709_RGB_YCBCR_CONV);
> + switch (crtc_state->infoframes.vsc.colorimetry) {
> + case DP_COLORIMETRY_BT2020_RGB:
> + case DP_COLORIMETRY_BT2020_YCC:
> + if (bt2020)
> + tmp =
> DP_CONVERSION_BT2020_RGB_YCBCR_ENABLE;
> + break;
> + case DP_COLORIMETRY_BT709_YCC:
> + case DP_COLORIMETRY_XVYCC_709:
> + if (bt709)
> + tmp =
> DP_CONVERSION_BT709_RGB_YCBCR_ENABLE;
> + break;
> + default:
> + break;
> + }
> + }
> +
> + if (drm_dp_pcon_convert_rgb_to_ycbcr(&intel_dp->aux, tmp) < 0)
> drm_dbg_kms(&i915->drm,
> - "Failed to set protocol converter YCbCr 4:2:2
> conversion mode to %s\n",
> - enableddisabled(false));
> + "Failed to set protocol converter RGB->YCbCr
> conversion mode to %s\n",
> + enableddisabled(tmp ? true : false));
> }
>
> static void intel_enable_dp(struct intel_atomic_state *state, @@ -4393,7
> +4428,7 @@ static void intel_enable_dp(struct intel_atomic_state *state,
> }
>
> intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
> - intel_dp_configure_protocol_converter(intel_dp);
> + intel_dp_configure_protocol_converter(intel_dp, pipe_config);
> intel_dp_check_frl_training(intel_dp);
> intel_dp_pcon_dsc_configure(intel_dp, pipe_config);
> intel_dp_start_link_train(intel_dp, pipe_config); @@ -6861,7 +6896,7
> @@ intel_dp_update_420(struct intel_dp *intel_dp) {
> struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> struct intel_connector *connector = intel_dp->attached_connector;
> - bool is_branch, ycbcr_420_passthrough, ycbcr_444_to_420;
> + bool is_branch, ycbcr_420_passthrough, ycbcr_444_to_420, rgb_to_ycbcr;
>
> /* No YCbCr output support on gmch platforms */
> if (HAS_GMCH(i915))
> @@ -6883,14 +6918,26 @@ intel_dp_update_420(struct intel_dp *intel_dp)
> dp_to_dig_port(intel_dp)->lspcon.active ||
> drm_dp_downstream_444_to_420_conversion(intel_dp->dpcd,
> intel_dp-
> >downstream_ports);
> + rgb_to_ycbcr = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp-
> >dpcd,
> + intel_dp-
> >downstream_ports,
> +
> DP_DS_HDMI_BT601_RGB_YCBCR_CONV ||
> +
> DP_DS_HDMI_BT709_RGB_YCBCR_CONV ||
> +
> DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
>
> if (INTEL_GEN(i915) >= 11) {
> + /* Let PCON convert from RGB->YCbCr if possible */
> + if (is_branch && rgb_to_ycbcr && ycbcr_444_to_420) {
> + intel_dp->dfp.rgb_to_ycbcr = true;
> + intel_dp->dfp.ycbcr_444_to_420 = true;
> + connector->base.ycbcr_420_allowed = true;
> + } else {
> /* Prefer 4:2:0 passthrough over 4:4:4->4:2:0 conversion */
> - intel_dp->dfp.ycbcr_444_to_420 =
> - ycbcr_444_to_420 && !ycbcr_420_passthrough;
> + intel_dp->dfp.ycbcr_444_to_420 =
> + ycbcr_444_to_420 && !ycbcr_420_passthrough;
>
> - connector->base.ycbcr_420_allowed =
> - !is_branch || ycbcr_444_to_420 ||
> ycbcr_420_passthrough;
> + connector->base.ycbcr_420_allowed =
> + !is_branch || ycbcr_444_to_420 ||
> ycbcr_420_passthrough;
> + }
> } else {
> /* 4:4:4->4:2:0 conversion is the only way */
> intel_dp->dfp.ycbcr_444_to_420 = ycbcr_444_to_420; @@ -
> 6899,8 +6946,9 @@ intel_dp_update_420(struct intel_dp *intel_dp)
> }
>
> drm_dbg_kms(&i915->drm,
> - "[CONNECTOR:%d:%s] YCbCr 4:2:0 allowed? %s, YCbCr 4:4:4-
> >4:2:0 conversion? %s\n",
> + "[CONNECTOR:%d:%s] RGB->YcbCr conversion? %s, YCbCr 4:2:0
> +allowed? %s, YCbCr 4:4:4->4:2:0 conversion? %s\n",
> connector->base.base.id, connector->base.name,
> + yesno(intel_dp->dfp.rgb_to_ycbcr),
> yesno(connector->base.ycbcr_420_allowed),
> yesno(intel_dp->dfp.ycbcr_444_to_420));
> }
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.h
> b/drivers/gpu/drm/i915/display/intel_dp.h
> index 1bfde4f89019..4280a09fd8fd 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.h
> +++ b/drivers/gpu/drm/i915/display/intel_dp.h
> @@ -51,7 +51,8 @@ int intel_dp_get_link_train_fallback_values(struct intel_dp
> *intel_dp, int intel_dp_retrain_link(struct intel_encoder *encoder,
> struct drm_modeset_acquire_ctx *ctx); void
> intel_dp_set_power(struct intel_dp *intel_dp, u8 mode); -void
> intel_dp_configure_protocol_converter(struct intel_dp *intel_dp);
> +void intel_dp_configure_protocol_converter(struct intel_dp *intel_dp,
> + const struct intel_crtc_state
> *crtc_state);
> void intel_dp_sink_set_decompression_state(struct intel_dp *intel_dp,
> const struct intel_crtc_state *crtc_state,
> bool enable);
> --
> 2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-HDMI2.1 PCON (rev9)
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
` (15 preceding siblings ...)
(?)
@ 2020-12-18 12:52 ` Patchwork
2020-12-22 16:43 ` Jani Nikula
-1 siblings, 1 reply; 57+ messages in thread
From: Patchwork @ 2020-12-18 12:52 UTC (permalink / raw)
To: Ankit Nautiyal; +Cc: intel-gfx
== Series Details ==
Series: Add support for DP-HDMI2.1 PCON (rev9)
URL : https://patchwork.freedesktop.org/series/82098/
State : warning
== Summary ==
$ dim checkpatch origin/drm-tip
26eb0c2f2ee1 drm/edid: Add additional HFVSDB fields for HDMI2.1
-:61: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-by: Sharma, Swati2 <swati2.sharma@intel.com>'
total: 0 errors, 1 warnings, 0 checks, 36 lines checked
13ffe829d77e drm/edid: Parse MAX_FRL field from HFVSDB block
-:73: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
#73: FILE: drivers/gpu/drm/drm_edid.c:4948:
+ drm_get_max_frl_rate(max_frl_rate, &hdmi->max_lanes,
+ &hdmi->max_frl_rate_per_lane);
-:95: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-by: Sharma, Swati2 <swati2.sharma@intel.com>'
total: 0 errors, 1 warnings, 1 checks, 68 lines checked
89853c019e04 drm/edid: Parse DSC1.2 cap fields from HFVSDB block
-:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
#51: FILE: drivers/gpu/drm/drm_edid.c:4969:
+ drm_get_max_frl_rate(dsc_max_frl_rate, &hdmi_dsc->max_lanes,
+ &hdmi_dsc->max_frl_rate_per_lane);
-:52: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
#52: FILE: drivers/gpu/drm/drm_edid.c:4970:
+ hdmi_dsc->total_chunk_kbytes = hf_vsdb[13] & DRM_EDID_DSC_TOTAL_CHUNK_KBYTES;
total: 0 errors, 1 warnings, 1 checks, 125 lines checked
5120b1727391 drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON
c68914ce7b67 drm/dp_helper: Add support for link failure detection
-:112: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
#112: FILE: include/drm/drm_dp_helper.h:2055:
+void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
+ struct drm_connector *connector);
total: 0 errors, 0 warnings, 1 checks, 76 lines checked
2f4d3c12ee27 drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon
-:15: WARNING:TYPO_SPELLING: 'Convertor' may be misspelled - perhaps 'Converter'?
#15:
v3: Only setting the DSC bits for the Protocol Convertor control
-:165: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */ on a separate line
#165: FILE: drivers/gpu/drm/drm_dp_helper.c:3037:
+ * */
-:185: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */ on a separate line
#185: FILE: drivers/gpu/drm/drm_dp_helper.c:3057:
+ * */
-:210: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */ on a separate line
#210: FILE: drivers/gpu/drm/drm_dp_helper.c:3082:
+ * */
total: 0 errors, 4 warnings, 0 checks, 343 lines checked
d1464a87a5a8 drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion
-:18: WARNING:TYPO_SPELLING: 'accomodate' may be misspelled - perhaps 'accommodate'?
#18:
-Modified the color-conversion cap helper function, to accomodate
total: 0 errors, 1 warnings, 0 checks, 106 lines checked
29e16a799211 drm/i915: Capture max frl rate for PCON in dfp cap structure
-:13: WARNING:COMMIT_LOG_LONG_LINE: Possible unwrapped commit description (prefer a maximum 75 chars per line)
#13:
-tweaked the comparison of target bw and pcon frl bw to avoid roundup errors.
total: 0 errors, 1 warnings, 0 checks, 60 lines checked
0f68d7283295 drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
-:86: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
#86: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4005:
+{
+
-:147: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
#147: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4066:
+ wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) == true, TIMEOUT_FRL_READY_MS);
-:166: WARNING:LONG_LINE: line length of 112 exceeds 100 columns
#166: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4085:
+ wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux) == true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
-:172: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
#172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
+ if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
-:172: WARNING:CONSTANT_COMPARISON: Comparisons should place the constant on the right side of the test
#172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
+ if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
-:176: WARNING:LONG_LINE: line length of 109 exceeds 100 columns
#176: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4095:
+ drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK = %u\n", max_frl_bw_mask, frl_trained_mask);
total: 0 errors, 5 warnings, 1 checks, 194 lines checked
3793f5252161 drm/i915: Check for FRL training before DP Link training
126578f6fe39 drm/i915: Add support for enabling link status and recovery
-:54: WARNING:LONG_LINE: line length of 107 exceeds 100 columns
#54: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6031:
+ drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux, &intel_dp->attached_connector->base);
total: 0 errors, 1 warnings, 0 checks, 83 lines checked
ca5d8df43ceb drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
-:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
#51: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4000:
+ if (drm_dp_dpcd_read(&intel_dp->aux, DP_PCON_DSC_ENCODER,
+ intel_dp->pcon_dsc_dpcd,
-:57: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
#57: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4006:
+ drm_dbg_kms(&i915->drm, "PCON ENCODER DSC DPCD: %*ph\n",
+ (int)sizeof(intel_dp->pcon_dsc_dpcd), intel_dp->pcon_dsc_dpcd);
total: 0 errors, 0 warnings, 2 checks, 39 lines checked
35f69a655bad drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1
-:57: WARNING:TYPO_SPELLING: 'capabilites' may be misspelled - perhaps 'capabilities'?
#57: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3458:
+ * and dsc decoder capabilites
-:143: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
#143: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3544:
+ if (min_slices <= 1 && src_max_slices >= 1 && hdmi_max_slices >= 1)
+ target_slices = 1;
-:145: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
#145: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3546:
+ else if (min_slices <= 2 && src_max_slices >= 2 && hdmi_max_slices >= 2)
+ target_slices = 2;
-:147: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
#147: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3548:
+ else if (min_slices <= 4 && src_max_slices >= 4 && hdmi_max_slices >= 4)
+ target_slices = 4;
-:149: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
#149: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3550:
+ else if (min_slices <= 8 && src_max_slices >= 8 && hdmi_max_slices >= 8)
+ target_slices = 8;
-:151: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
#151: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3552:
+ else if (min_slices <= 12 && src_max_slices >= 12 && hdmi_max_slices >= 12)
+ target_slices = 12;
-:153: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
#153: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3554:
+ else if (min_slices <= 16 && src_max_slices >= 16 && hdmi_max_slices >= 16)
+ target_slices = 16;
total: 0 errors, 7 warnings, 0 checks, 248 lines checked
34ee9dfdadfd drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
-:75: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
#75: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4171:
+{
+
-:92: CHECK:LINE_SPACING: Please don't use multiple blank lines
#92: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4188:
+
+
-:155: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
#155: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4251:
+ bits_per_pixel = intel_dp_pcon_dsc_enc_bpp(intel_dp, crtc_state,
+ num_slices, slice_width);
total: 0 errors, 0 warnings, 3 checks, 157 lines checked
d739034947bb drm/i915/display: Let PCON convert from RGB to YCbCr if it can
-:104: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
#104: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4368:
+ DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
-:156: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
#156: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6922:
+ rgb_to_ycbcr = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
+ intel_dp->downstream_ports,
total: 0 errors, 1 warnings, 1 checks, 152 lines checked
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* [Intel-gfx] ✗ Fi.CI.SPARSE: warning for Add support for DP-HDMI2.1 PCON (rev9)
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
` (16 preceding siblings ...)
(?)
@ 2020-12-18 12:55 ` Patchwork
-1 siblings, 0 replies; 57+ messages in thread
From: Patchwork @ 2020-12-18 12:55 UTC (permalink / raw)
To: Ankit Nautiyal; +Cc: intel-gfx
== Series Details ==
Series: Add support for DP-HDMI2.1 PCON (rev9)
URL : https://patchwork.freedesktop.org/series/82098/
State : warning
== Summary ==
$ dim sparse --fast origin/drm-tip
Sparse version: v0.6.2
Fast mode used, each commit won't be checked separately.
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:261:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1398:25: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1398:25: struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1398:25: struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1399:17: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1399:17: struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1399:17: struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1458:17: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1458:17: struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1458:17: struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:285:16: error: incompatible types in comparison expression (different type sizes):
+drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:285:16: unsigned long *
+drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:285:16: unsigned long long *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:276:25: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:276:25: struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:276:25: struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:277:17: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:277:17: struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:277:17: struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:331:17: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:331:17: struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:331:17: struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_ras_eeprom.h:92:56: error: marked inline, but without a definition
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:257:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amd
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* [Intel-gfx] ✓ Fi.CI.BAT: success for Add support for DP-HDMI2.1 PCON (rev9)
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
` (17 preceding siblings ...)
(?)
@ 2020-12-18 13:21 ` Patchwork
-1 siblings, 0 replies; 57+ messages in thread
From: Patchwork @ 2020-12-18 13:21 UTC (permalink / raw)
To: Ankit Nautiyal; +Cc: intel-gfx
[-- Attachment #1.1: Type: text/plain, Size: 3618 bytes --]
== Series Details ==
Series: Add support for DP-HDMI2.1 PCON (rev9)
URL : https://patchwork.freedesktop.org/series/82098/
State : success
== Summary ==
CI Bug Log - changes from CI_DRM_9503 -> Patchwork_19177
====================================================
Summary
-------
**SUCCESS**
No regressions found.
External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/index.html
Known issues
------------
Here are the changes found in Patchwork_19177 that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@prime_vgem@basic-read:
- fi-tgl-y: [PASS][1] -> [DMESG-WARN][2] ([i915#402]) +2 similar issues
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/fi-tgl-y/igt@prime_vgem@basic-read.html
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/fi-tgl-y/igt@prime_vgem@basic-read.html
#### Possible fixes ####
* igt@i915_selftest@live@active:
- fi-kbl-r: [DMESG-FAIL][3] ([i915#2291] / [i915#666]) -> [PASS][4]
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/fi-kbl-r/igt@i915_selftest@live@active.html
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/fi-kbl-r/igt@i915_selftest@live@active.html
* igt@prime_self_import@basic-with_one_bo_two_files:
- fi-tgl-y: [DMESG-WARN][5] ([i915#402]) -> [PASS][6] +1 similar issue
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/fi-tgl-y/igt@prime_self_import@basic-with_one_bo_two_files.html
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/fi-tgl-y/igt@prime_self_import@basic-with_one_bo_two_files.html
[i915#2291]: https://gitlab.freedesktop.org/drm/intel/issues/2291
[i915#402]: https://gitlab.freedesktop.org/drm/intel/issues/402
[i915#666]: https://gitlab.freedesktop.org/drm/intel/issues/666
Participating hosts (42 -> 39)
------------------------------
Missing (3): fi-ilk-m540 fi-bdw-samus fi-hsw-4200u
Build changes
-------------
* Linux: CI_DRM_9503 -> Patchwork_19177
CI-20190529: 20190529
CI_DRM_9503: 82c5c0ad8d578504865837b2135b60dd2d0054a1 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_5909: 3d6caf71a3e988cd125eb9efdd0a7cdcd0451673 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_19177: d739034947bb5b262c819a0e4a0a1c01beef9e01 @ git://anongit.freedesktop.org/gfx-ci/linux
== Linux commits ==
d739034947bb drm/i915/display: Let PCON convert from RGB to YCbCr if it can
34ee9dfdadfd drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
35f69a655bad drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1
ca5d8df43ceb drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
126578f6fe39 drm/i915: Add support for enabling link status and recovery
3793f5252161 drm/i915: Check for FRL training before DP Link training
0f68d7283295 drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
29e16a799211 drm/i915: Capture max frl rate for PCON in dfp cap structure
d1464a87a5a8 drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion
2f4d3c12ee27 drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon
c68914ce7b67 drm/dp_helper: Add support for link failure detection
5120b1727391 drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON
89853c019e04 drm/edid: Parse DSC1.2 cap fields from HFVSDB block
13ffe829d77e drm/edid: Parse MAX_FRL field from HFVSDB block
26eb0c2f2ee1 drm/edid: Add additional HFVSDB fields for HDMI2.1
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/index.html
[-- Attachment #1.2: Type: text/html, Size: 4424 bytes --]
[-- Attachment #2: Type: text/plain, Size: 160 bytes --]
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* [Intel-gfx] ✓ Fi.CI.IGT: success for Add support for DP-HDMI2.1 PCON (rev9)
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
` (18 preceding siblings ...)
(?)
@ 2020-12-18 15:37 ` Patchwork
-1 siblings, 0 replies; 57+ messages in thread
From: Patchwork @ 2020-12-18 15:37 UTC (permalink / raw)
To: Ankit Nautiyal; +Cc: intel-gfx
[-- Attachment #1.1: Type: text/plain, Size: 18574 bytes --]
== Series Details ==
Series: Add support for DP-HDMI2.1 PCON (rev9)
URL : https://patchwork.freedesktop.org/series/82098/
State : success
== Summary ==
CI Bug Log - changes from CI_DRM_9503_full -> Patchwork_19177_full
====================================================
Summary
-------
**SUCCESS**
No regressions found.
Known issues
------------
Here are the changes found in Patchwork_19177_full that come from known issues:
### IGT changes ###
#### Issues hit ####
* igt@gem_ctx_persistence@legacy-engines-cleanup:
- shard-hsw: NOTRUN -> [SKIP][1] ([fdo#109271] / [i915#1099])
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-hsw8/igt@gem_ctx_persistence@legacy-engines-cleanup.html
* igt@gem_exec_reloc@basic-many-active@vcs1:
- shard-iclb: NOTRUN -> [FAIL][2] ([i915#2389])
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-iclb2/igt@gem_exec_reloc@basic-many-active@vcs1.html
* igt@gem_huc_copy@huc-copy:
- shard-tglb: [PASS][3] -> [SKIP][4] ([i915#2190])
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-tglb1/igt@gem_huc_copy@huc-copy.html
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-tglb6/igt@gem_huc_copy@huc-copy.html
* igt@gen9_exec_parse@allowed-all:
- shard-skl: [PASS][5] -> [DMESG-WARN][6] ([i915#1436] / [i915#716])
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl3/igt@gen9_exec_parse@allowed-all.html
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl4/igt@gen9_exec_parse@allowed-all.html
- shard-glk: [PASS][7] -> [DMESG-WARN][8] ([i915#1436] / [i915#716])
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-glk9/igt@gen9_exec_parse@allowed-all.html
[8]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-glk6/igt@gen9_exec_parse@allowed-all.html
* igt@i915_pm_dc@dc6-dpms:
- shard-skl: NOTRUN -> [FAIL][9] ([i915#454]) +1 similar issue
[9]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl10/igt@i915_pm_dc@dc6-dpms.html
* igt@i915_pm_rpm@system-suspend-execbuf:
- shard-skl: [PASS][10] -> [INCOMPLETE][11] ([i915#151])
[10]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl2/igt@i915_pm_rpm@system-suspend-execbuf.html
[11]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl4/igt@i915_pm_rpm@system-suspend-execbuf.html
* igt@kms_async_flips@test-time-stamp:
- shard-tglb: [PASS][12] -> [FAIL][13] ([i915#2574])
[12]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-tglb5/igt@kms_async_flips@test-time-stamp.html
[13]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-tglb7/igt@kms_async_flips@test-time-stamp.html
* igt@kms_chamelium@hdmi-edid-change-during-suspend:
- shard-apl: NOTRUN -> [SKIP][14] ([fdo#109271] / [fdo#111827]) +3 similar issues
[14]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-apl2/igt@kms_chamelium@hdmi-edid-change-during-suspend.html
* igt@kms_chamelium@hdmi-hpd-for-each-pipe:
- shard-hsw: NOTRUN -> [SKIP][15] ([fdo#109271] / [fdo#111827]) +2 similar issues
[15]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-hsw8/igt@kms_chamelium@hdmi-hpd-for-each-pipe.html
* igt@kms_color_chamelium@pipe-c-gamma:
- shard-skl: NOTRUN -> [SKIP][16] ([fdo#109271] / [fdo#111827]) +4 similar issues
[16]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl10/igt@kms_color_chamelium@pipe-c-gamma.html
* igt@kms_cursor_crc@pipe-b-cursor-256x256-sliding:
- shard-skl: [PASS][17] -> [FAIL][18] ([i915#54])
[17]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl9/igt@kms_cursor_crc@pipe-b-cursor-256x256-sliding.html
[18]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl8/igt@kms_cursor_crc@pipe-b-cursor-256x256-sliding.html
* igt@kms_cursor_crc@pipe-b-cursor-64x21-random:
- shard-apl: [PASS][19] -> [FAIL][20] ([i915#54])
[19]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-apl6/igt@kms_cursor_crc@pipe-b-cursor-64x21-random.html
[20]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-apl1/igt@kms_cursor_crc@pipe-b-cursor-64x21-random.html
* igt@kms_cursor_crc@pipe-c-cursor-64x21-random:
- shard-skl: NOTRUN -> [FAIL][21] ([i915#54])
[21]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl8/igt@kms_cursor_crc@pipe-c-cursor-64x21-random.html
* igt@kms_cursor_edge_walk@pipe-a-128x128-right-edge:
- shard-glk: [PASS][22] -> [DMESG-FAIL][23] ([i915#118] / [i915#70] / [i915#95])
[22]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-glk1/igt@kms_cursor_edge_walk@pipe-a-128x128-right-edge.html
[23]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-glk5/igt@kms_cursor_edge_walk@pipe-a-128x128-right-edge.html
* igt@kms_cursor_legacy@pipe-d-torture-bo:
- shard-apl: NOTRUN -> [SKIP][24] ([fdo#109271] / [i915#533])
[24]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-apl2/igt@kms_cursor_legacy@pipe-d-torture-bo.html
* igt@kms_flip@2x-flip-vs-panning-vs-hang:
- shard-skl: NOTRUN -> [SKIP][25] ([fdo#109271]) +34 similar issues
[25]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl10/igt@kms_flip@2x-flip-vs-panning-vs-hang.html
* igt@kms_flip@flip-vs-suspend@a-edp1:
- shard-skl: [PASS][26] -> [INCOMPLETE][27] ([i915#198])
[26]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl5/igt@kms_flip@flip-vs-suspend@a-edp1.html
[27]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl2/igt@kms_flip@flip-vs-suspend@a-edp1.html
* igt@kms_frontbuffer_tracking@psr-1p-primscrn-shrfb-pgflip-blt:
- shard-apl: NOTRUN -> [SKIP][28] ([fdo#109271]) +19 similar issues
[28]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-apl2/igt@kms_frontbuffer_tracking@psr-1p-primscrn-shrfb-pgflip-blt.html
* igt@kms_pipe_crc_basic@suspend-read-crc-pipe-d:
- shard-skl: NOTRUN -> [SKIP][29] ([fdo#109271] / [i915#533]) +1 similar issue
[29]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl10/igt@kms_pipe_crc_basic@suspend-read-crc-pipe-d.html
* igt@kms_plane_alpha_blend@pipe-a-alpha-transparent-fb:
- shard-apl: NOTRUN -> [FAIL][30] ([i915#265])
[30]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-apl2/igt@kms_plane_alpha_blend@pipe-a-alpha-transparent-fb.html
* igt@kms_plane_alpha_blend@pipe-c-constant-alpha-max:
- shard-skl: NOTRUN -> [FAIL][31] ([fdo#108145] / [i915#265])
[31]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl1/igt@kms_plane_alpha_blend@pipe-c-constant-alpha-max.html
* igt@kms_psr2_su@page_flip:
- shard-iclb: [PASS][32] -> [SKIP][33] ([fdo#109642] / [fdo#111068])
[32]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-iclb2/igt@kms_psr2_su@page_flip.html
[33]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-iclb7/igt@kms_psr2_su@page_flip.html
* igt@kms_psr@psr2_basic:
- shard-iclb: [PASS][34] -> [SKIP][35] ([fdo#109441]) +1 similar issue
[34]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-iclb2/igt@kms_psr@psr2_basic.html
[35]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-iclb3/igt@kms_psr@psr2_basic.html
* igt@perf@polling:
- shard-skl: [PASS][36] -> [FAIL][37] ([i915#1542])
[36]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl1/igt@perf@polling.html
[37]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl4/igt@perf@polling.html
* igt@prime_nv_api@i915_nv_import_twice:
- shard-hsw: NOTRUN -> [SKIP][38] ([fdo#109271]) +45 similar issues
[38]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-hsw8/igt@prime_nv_api@i915_nv_import_twice.html
#### Possible fixes ####
* {igt@gem_exec_schedule@u-fairslice@rcs0}:
- shard-apl: [DMESG-WARN][39] ([i915#1610]) -> [PASS][40]
[39]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-apl4/igt@gem_exec_schedule@u-fairslice@rcs0.html
[40]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-apl2/igt@gem_exec_schedule@u-fairslice@rcs0.html
* igt@gem_exec_whisper@basic-queues-priority-all:
- shard-glk: [DMESG-WARN][41] ([i915#118] / [i915#95]) -> [PASS][42]
[41]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-glk6/igt@gem_exec_whisper@basic-queues-priority-all.html
[42]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-glk8/igt@gem_exec_whisper@basic-queues-priority-all.html
* igt@i915_pm_dc@dc6-psr:
- shard-iclb: [FAIL][43] ([i915#454]) -> [PASS][44]
[43]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-iclb6/igt@i915_pm_dc@dc6-psr.html
[44]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-iclb8/igt@i915_pm_dc@dc6-psr.html
* igt@i915_pm_rpm@modeset-non-lpsp-stress:
- shard-kbl: [DMESG-WARN][45] ([i915#165] / [i915#180]) -> [PASS][46]
[45]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-kbl2/igt@i915_pm_rpm@modeset-non-lpsp-stress.html
[46]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-kbl6/igt@i915_pm_rpm@modeset-non-lpsp-stress.html
* igt@kms_async_flips@alternate-sync-async-flip:
- shard-skl: [FAIL][47] ([i915#2521]) -> [PASS][48]
[47]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl1/igt@kms_async_flips@alternate-sync-async-flip.html
[48]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl10/igt@kms_async_flips@alternate-sync-async-flip.html
* igt@kms_cursor_crc@pipe-a-cursor-256x256-random:
- shard-skl: [FAIL][49] ([i915#54]) -> [PASS][50] +2 similar issues
[49]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl10/igt@kms_cursor_crc@pipe-a-cursor-256x256-random.html
[50]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl5/igt@kms_cursor_crc@pipe-a-cursor-256x256-random.html
* igt@kms_flip@plain-flip-ts-check@a-edp1:
- shard-skl: [FAIL][51] ([i915#2122]) -> [PASS][52]
[51]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl3/igt@kms_flip@plain-flip-ts-check@a-edp1.html
[52]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl4/igt@kms_flip@plain-flip-ts-check@a-edp1.html
* igt@kms_hdr@bpc-switch:
- shard-skl: [FAIL][53] ([i915#1188]) -> [PASS][54]
[53]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl4/igt@kms_hdr@bpc-switch.html
[54]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl1/igt@kms_hdr@bpc-switch.html
* igt@kms_pipe_crc_basic@suspend-read-crc-pipe-c:
- shard-skl: [INCOMPLETE][55] ([i915#198]) -> [PASS][56]
[55]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl7/igt@kms_pipe_crc_basic@suspend-read-crc-pipe-c.html
[56]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl10/igt@kms_pipe_crc_basic@suspend-read-crc-pipe-c.html
* igt@kms_plane@plane-panning-bottom-right-pipe-a-planes:
- shard-skl: [FAIL][57] ([i915#1036]) -> [PASS][58]
[57]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl10/igt@kms_plane@plane-panning-bottom-right-pipe-a-planes.html
[58]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl2/igt@kms_plane@plane-panning-bottom-right-pipe-a-planes.html
* igt@kms_plane_alpha_blend@pipe-a-coverage-7efc:
- shard-skl: [FAIL][59] ([fdo#108145] / [i915#265]) -> [PASS][60]
[59]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl5/igt@kms_plane_alpha_blend@pipe-a-coverage-7efc.html
[60]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl2/igt@kms_plane_alpha_blend@pipe-a-coverage-7efc.html
* igt@kms_psr@psr2_cursor_render:
- shard-iclb: [SKIP][61] ([fdo#109441]) -> [PASS][62] +2 similar issues
[61]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-iclb7/igt@kms_psr@psr2_cursor_render.html
[62]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-iclb2/igt@kms_psr@psr2_cursor_render.html
#### Warnings ####
* igt@gem_exec_suspend@basic-s0:
- shard-tglb: [DMESG-WARN][63] ([i915#1436] / [i915#1602] / [i915#1887] / [i915#2411]) -> [DMESG-WARN][64] ([i915#1602] / [i915#2411])
[63]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-tglb1/igt@gem_exec_suspend@basic-s0.html
[64]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-tglb3/igt@gem_exec_suspend@basic-s0.html
* igt@i915_pm_dc@dc3co-vpb-simulation:
- shard-iclb: [SKIP][65] ([i915#658]) -> [SKIP][66] ([i915#588])
[65]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-iclb7/igt@i915_pm_dc@dc3co-vpb-simulation.html
[66]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-iclb2/igt@i915_pm_dc@dc3co-vpb-simulation.html
* igt@i915_pm_rc6_residency@rc6-fence:
- shard-iclb: [WARN][67] ([i915#2684]) -> [WARN][68] ([i915#1804] / [i915#2684])
[67]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-iclb2/igt@i915_pm_rc6_residency@rc6-fence.html
[68]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-iclb7/igt@i915_pm_rc6_residency@rc6-fence.html
* igt@runner@aborted:
- shard-apl: ([FAIL][69], [FAIL][70], [FAIL][71]) ([i915#1610] / [i915#2295] / [i915#2426]) -> ([FAIL][72], [FAIL][73]) ([i915#2295])
[69]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-apl4/igt@runner@aborted.html
[70]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-apl4/igt@runner@aborted.html
[71]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-apl8/igt@runner@aborted.html
[72]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-apl3/igt@runner@aborted.html
[73]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-apl2/igt@runner@aborted.html
- shard-skl: ([FAIL][74], [FAIL][75]) ([i915#2295]) -> ([FAIL][76], [FAIL][77], [FAIL][78], [FAIL][79]) ([i915#1436] / [i915#2295] / [i915#2426] / [i915#483])
[74]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl2/igt@runner@aborted.html
[75]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_9503/shard-skl10/igt@runner@aborted.html
[76]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl2/igt@runner@aborted.html
[77]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl5/igt@runner@aborted.html
[78]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl4/igt@runner@aborted.html
[79]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/shard-skl10/igt@runner@aborted.html
{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).
[fdo#108145]: https://bugs.freedesktop.org/show_bug.cgi?id=108145
[fdo#109271]: https://bugs.freedesktop.org/show_bug.cgi?id=109271
[fdo#109441]: https://bugs.freedesktop.org/show_bug.cgi?id=109441
[fdo#109642]: https://bugs.freedesktop.org/show_bug.cgi?id=109642
[fdo#111068]: https://bugs.freedesktop.org/show_bug.cgi?id=111068
[fdo#111827]: https://bugs.freedesktop.org/show_bug.cgi?id=111827
[i915#1036]: https://gitlab.freedesktop.org/drm/intel/issues/1036
[i915#1099]: https://gitlab.freedesktop.org/drm/intel/issues/1099
[i915#118]: https://gitlab.freedesktop.org/drm/intel/issues/118
[i915#1188]: https://gitlab.freedesktop.org/drm/intel/issues/1188
[i915#1436]: https://gitlab.freedesktop.org/drm/intel/issues/1436
[i915#151]: https://gitlab.freedesktop.org/drm/intel/issues/151
[i915#1542]: https://gitlab.freedesktop.org/drm/intel/issues/1542
[i915#1602]: https://gitlab.freedesktop.org/drm/intel/issues/1602
[i915#1610]: https://gitlab.freedesktop.org/drm/intel/issues/1610
[i915#165]: https://gitlab.freedesktop.org/drm/intel/issues/165
[i915#180]: https://gitlab.freedesktop.org/drm/intel/issues/180
[i915#1804]: https://gitlab.freedesktop.org/drm/intel/issues/1804
[i915#1887]: https://gitlab.freedesktop.org/drm/intel/issues/1887
[i915#198]: https://gitlab.freedesktop.org/drm/intel/issues/198
[i915#2122]: https://gitlab.freedesktop.org/drm/intel/issues/2122
[i915#2190]: https://gitlab.freedesktop.org/drm/intel/issues/2190
[i915#2295]: https://gitlab.freedesktop.org/drm/intel/issues/2295
[i915#2389]: https://gitlab.freedesktop.org/drm/intel/issues/2389
[i915#2411]: https://gitlab.freedesktop.org/drm/intel/issues/2411
[i915#2426]: https://gitlab.freedesktop.org/drm/intel/issues/2426
[i915#2521]: https://gitlab.freedesktop.org/drm/intel/issues/2521
[i915#2574]: https://gitlab.freedesktop.org/drm/intel/issues/2574
[i915#265]: https://gitlab.freedesktop.org/drm/intel/issues/265
[i915#2684]: https://gitlab.freedesktop.org/drm/intel/issues/2684
[i915#454]: https://gitlab.freedesktop.org/drm/intel/issues/454
[i915#483]: https://gitlab.freedesktop.org/drm/intel/issues/483
[i915#533]: https://gitlab.freedesktop.org/drm/intel/issues/533
[i915#54]: https://gitlab.freedesktop.org/drm/intel/issues/54
[i915#588]: https://gitlab.freedesktop.org/drm/intel/issues/588
[i915#658]: https://gitlab.freedesktop.org/drm/intel/issues/658
[i915#70]: https://gitlab.freedesktop.org/drm/intel/issues/70
[i915#716]: https://gitlab.freedesktop.org/drm/intel/issues/716
[i915#95]: https://gitlab.freedesktop.org/drm/intel/issues/95
Participating hosts (10 -> 10)
------------------------------
No changes in participating hosts
Build changes
-------------
* Linux: CI_DRM_9503 -> Patchwork_19177
CI-20190529: 20190529
CI_DRM_9503: 82c5c0ad8d578504865837b2135b60dd2d0054a1 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_5909: 3d6caf71a3e988cd125eb9efdd0a7cdcd0451673 @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_19177: d739034947bb5b262c819a0e4a0a1c01beef9e01 @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_19177/index.html
[-- Attachment #1.2: Type: text/html, Size: 22762 bytes --]
[-- Attachment #2: Type: text/plain, Size: 160 bytes --]
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [PATCH v7 00/15] Add support for DP-HDMI2.1 PCON
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2020-12-22 16:28 ` Jani Nikula
-1 siblings, 0 replies; 57+ messages in thread
From: Jani Nikula @ 2020-12-22 16:28 UTC (permalink / raw)
To: Ankit Nautiyal, intel-gfx
Cc: airlied, Daniel Vetter, dri-devel, vandita.kulkarni, uma.shankar,
swati2.sharma, Thomas Zimmermann, Rodrigo Vivi
On Fri, 18 Dec 2020, Ankit Nautiyal <ankit.k.nautiyal@intel.com> wrote:
> This patch series attempts to add support for a DP-HDMI2.1 Protocol
> Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
> E5 to DisplayPort_v2.0:
> https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
> The details are mentioned in:
> VESA DP-to-HDMI PCON Specification Standalone Document
> https://groups.vesa.org/wg/DP/document/15651
Thanks for the patches and review.
I've pushed the series to a new topic branch topic/dp-hdmi-2.1-pcon as
discussed with Maarten and Daniel a while back. I've used 'git
merge-base drm-misc/drm-misc-next drm-intel/drm-intel-next' as the base
to allow merging to both. I'll send pull requests soon, and wait for the
drm-misc-next merge before merging to i915.
BR,
Jani.
>
> This series starts with adding support for FRL (Fixed Rate Link)
> Training between the PCON and HDMI2.1 sink.
> As per HDMI2.1 specification, a new data-channel or lane is added in
> FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
> bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
> lanes).
>
> With these patches, the HDMI2.1 PCON can be configured to achieve FRL
> training based on the maximum FRL rate supported by the panel, source
> and the PCON.
> The approach is to add the support for FRL training between PCON and
> HDMI2.1 sink and gradually add other blocks for supporting higher
> resolutions and other HDMI2.1 features, that can be supported by pcon
> for the sources that do not natively support HDMI2.1.
>
> This is done before the DP Link training between the source and PCON
> is started. In case of FRL training is not achieved, the PCON will
> work in the regular TMDS mode, without HDMI2.1 feature support.
> Any interruption in FRL training between the PCON and HDMI2.1 sink is
> notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
> registers are read and FRL training is re-attempted.
>
> Currently, we have tested the FRL training and are able to enable 4K
> display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
> panel.
>
> v2: Addressed review comments and re-organized patches as suggested in
> comments on RFC patches.
>
> v3: Addressed review comments on previous version.
>
> v4: Added support for RGB->YCBCR conversion through PCON
>
> v5: Addressed review comments on previous version.
>
> v6: Fix typo in one of the patch.
>
> v7: Rebased on latest drm-tip and addressed the review comments.
>
> Ankit Nautiyal (11):
> drm/edid: Parse DSC1.2 cap fields from HFVSDB block
> drm/dp_helper: Add Helpers for FRL Link Training support for
> DP-HDMI2.1 PCON
> drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon
> drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion
> drm/i915: Capture max frl rate for PCON in dfp cap structure
> drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
> drm/i915: Check for FRL training before DP Link training
> drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
> drm/i915: Add helper functions for calculating DSC parameters for
> HDMI2.1
> drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
> drm/i915/display: Let PCON convert from RGB to YCbCr if it can
>
> Swati Sharma (4):
> drm/edid: Add additional HFVSDB fields for HDMI2.1
> drm/edid: Parse MAX_FRL field from HFVSDB block
> drm/dp_helper: Add support for link failure detection
> drm/i915: Add support for enabling link status and recovery
>
> drivers/gpu/drm/drm_dp_helper.c | 566 ++++++++++++++++++
> drivers/gpu/drm/drm_edid.c | 103 ++++
> drivers/gpu/drm/i915/display/intel_ddi.c | 6 +-
> .../drm/i915/display/intel_display_types.h | 10 +
> drivers/gpu/drm/i915/display/intel_dp.c | 442 +++++++++++++-
> drivers/gpu/drm/i915/display/intel_dp.h | 7 +-
> drivers/gpu/drm/i915/display/intel_hdmi.c | 233 +++++++
> drivers/gpu/drm/i915/display/intel_hdmi.h | 7 +
> include/drm/drm_connector.h | 49 ++
> include/drm/drm_dp_helper.h | 218 +++++++
> include/drm/drm_edid.h | 30 +
> 11 files changed, 1652 insertions(+), 19 deletions(-)
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] [PATCH v7 00/15] Add support for DP-HDMI2.1 PCON
@ 2020-12-22 16:28 ` Jani Nikula
0 siblings, 0 replies; 57+ messages in thread
From: Jani Nikula @ 2020-12-22 16:28 UTC (permalink / raw)
To: Ankit Nautiyal, intel-gfx
Cc: Maxime Ripard, airlied, Daniel Vetter, dri-devel, Thomas Zimmermann
On Fri, 18 Dec 2020, Ankit Nautiyal <ankit.k.nautiyal@intel.com> wrote:
> This patch series attempts to add support for a DP-HDMI2.1 Protocol
> Convertor. The VESA spec for the HDMI2.1 PCON are proposed in Errata
> E5 to DisplayPort_v2.0:
> https://vesa.org/join-vesamemberships/member-downloads/?action=stamp&fileid=42299
> The details are mentioned in:
> VESA DP-to-HDMI PCON Specification Standalone Document
> https://groups.vesa.org/wg/DP/document/15651
Thanks for the patches and review.
I've pushed the series to a new topic branch topic/dp-hdmi-2.1-pcon as
discussed with Maarten and Daniel a while back. I've used 'git
merge-base drm-misc/drm-misc-next drm-intel/drm-intel-next' as the base
to allow merging to both. I'll send pull requests soon, and wait for the
drm-misc-next merge before merging to i915.
BR,
Jani.
>
> This series starts with adding support for FRL (Fixed Rate Link)
> Training between the PCON and HDMI2.1 sink.
> As per HDMI2.1 specification, a new data-channel or lane is added in
> FRL mode, by repurposing the TMDS clock Channel. Through FRL, higher
> bit-rate can be supported, ie. up to 12 Gbps/lane (48 Gbps over 4
> lanes).
>
> With these patches, the HDMI2.1 PCON can be configured to achieve FRL
> training based on the maximum FRL rate supported by the panel, source
> and the PCON.
> The approach is to add the support for FRL training between PCON and
> HDMI2.1 sink and gradually add other blocks for supporting higher
> resolutions and other HDMI2.1 features, that can be supported by pcon
> for the sources that do not natively support HDMI2.1.
>
> This is done before the DP Link training between the source and PCON
> is started. In case of FRL training is not achieved, the PCON will
> work in the regular TMDS mode, without HDMI2.1 feature support.
> Any interruption in FRL training between the PCON and HDMI2.1 sink is
> notified through IRQ_HPD. On receiving the IRQ_HPD the concerned DPCD
> registers are read and FRL training is re-attempted.
>
> Currently, we have tested the FRL training and are able to enable 4K
> display with TGL Platform + Realtek PCON RTD2173 with HDMI2.1 supporting
> panel.
>
> v2: Addressed review comments and re-organized patches as suggested in
> comments on RFC patches.
>
> v3: Addressed review comments on previous version.
>
> v4: Added support for RGB->YCBCR conversion through PCON
>
> v5: Addressed review comments on previous version.
>
> v6: Fix typo in one of the patch.
>
> v7: Rebased on latest drm-tip and addressed the review comments.
>
> Ankit Nautiyal (11):
> drm/edid: Parse DSC1.2 cap fields from HFVSDB block
> drm/dp_helper: Add Helpers for FRL Link Training support for
> DP-HDMI2.1 PCON
> drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon
> drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion
> drm/i915: Capture max frl rate for PCON in dfp cap structure
> drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
> drm/i915: Check for FRL training before DP Link training
> drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
> drm/i915: Add helper functions for calculating DSC parameters for
> HDMI2.1
> drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
> drm/i915/display: Let PCON convert from RGB to YCbCr if it can
>
> Swati Sharma (4):
> drm/edid: Add additional HFVSDB fields for HDMI2.1
> drm/edid: Parse MAX_FRL field from HFVSDB block
> drm/dp_helper: Add support for link failure detection
> drm/i915: Add support for enabling link status and recovery
>
> drivers/gpu/drm/drm_dp_helper.c | 566 ++++++++++++++++++
> drivers/gpu/drm/drm_edid.c | 103 ++++
> drivers/gpu/drm/i915/display/intel_ddi.c | 6 +-
> .../drm/i915/display/intel_display_types.h | 10 +
> drivers/gpu/drm/i915/display/intel_dp.c | 442 +++++++++++++-
> drivers/gpu/drm/i915/display/intel_dp.h | 7 +-
> drivers/gpu/drm/i915/display/intel_hdmi.c | 233 +++++++
> drivers/gpu/drm/i915/display/intel_hdmi.h | 7 +
> include/drm/drm_connector.h | 49 ++
> include/drm/drm_dp_helper.h | 218 +++++++
> include/drm/drm_edid.h | 30 +
> 11 files changed, 1652 insertions(+), 19 deletions(-)
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-HDMI2.1 PCON (rev9)
2020-12-18 12:52 ` [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-HDMI2.1 PCON (rev9) Patchwork
@ 2020-12-22 16:43 ` Jani Nikula
2020-12-23 5:56 ` Nautiyal, Ankit K
0 siblings, 1 reply; 57+ messages in thread
From: Jani Nikula @ 2020-12-22 16:43 UTC (permalink / raw)
To: Ankit Nautiyal, swati2.sharma, uma.shankar; +Cc: intel-gfx
On Fri, 18 Dec 2020, Patchwork <patchwork@emeril.freedesktop.org> wrote:
> == Series Details ==
>
> Series: Add support for DP-HDMI2.1 PCON (rev9)
> URL : https://patchwork.freedesktop.org/series/82098/
> State : warning
>
> == Summary ==
>
All -
I've fixed most of the checkpatch warnings (save for LONG_LINE and
BIT_MACRO that we don't care so much about) while applying. It's not
something I normally do, and I really don't want to find these when the
series is at v7 and the same warnings have been there since September
and I keep being pinged about merging.
Keeping the driver nice and clean is your job too, not just mine.
BR,
Jani.
> $ dim checkpatch origin/drm-tip
> 26eb0c2f2ee1 drm/edid: Add additional HFVSDB fields for HDMI2.1
> -:61: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-by: Sharma, Swati2 <swati2.sharma@intel.com>'
>
> total: 0 errors, 1 warnings, 0 checks, 36 lines checked
> 13ffe829d77e drm/edid: Parse MAX_FRL field from HFVSDB block
> -:73: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
> #73: FILE: drivers/gpu/drm/drm_edid.c:4948:
> + drm_get_max_frl_rate(max_frl_rate, &hdmi->max_lanes,
> + &hdmi->max_frl_rate_per_lane);
>
> -:95: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-by: Sharma, Swati2 <swati2.sharma@intel.com>'
>
> total: 0 errors, 1 warnings, 1 checks, 68 lines checked
> 89853c019e04 drm/edid: Parse DSC1.2 cap fields from HFVSDB block
> -:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
> #51: FILE: drivers/gpu/drm/drm_edid.c:4969:
> + drm_get_max_frl_rate(dsc_max_frl_rate, &hdmi_dsc->max_lanes,
> + &hdmi_dsc->max_frl_rate_per_lane);
>
> -:52: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
> #52: FILE: drivers/gpu/drm/drm_edid.c:4970:
> + hdmi_dsc->total_chunk_kbytes = hf_vsdb[13] & DRM_EDID_DSC_TOTAL_CHUNK_KBYTES;
>
> total: 0 errors, 1 warnings, 1 checks, 125 lines checked
> 5120b1727391 drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON
> c68914ce7b67 drm/dp_helper: Add support for link failure detection
> -:112: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
> #112: FILE: include/drm/drm_dp_helper.h:2055:
> +void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
> + struct drm_connector *connector);
>
> total: 0 errors, 0 warnings, 1 checks, 76 lines checked
> 2f4d3c12ee27 drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon
> -:15: WARNING:TYPO_SPELLING: 'Convertor' may be misspelled - perhaps 'Converter'?
> #15:
> v3: Only setting the DSC bits for the Protocol Convertor control
>
> -:165: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */ on a separate line
> #165: FILE: drivers/gpu/drm/drm_dp_helper.c:3037:
> + * */
>
> -:185: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */ on a separate line
> #185: FILE: drivers/gpu/drm/drm_dp_helper.c:3057:
> + * */
>
> -:210: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */ on a separate line
> #210: FILE: drivers/gpu/drm/drm_dp_helper.c:3082:
> + * */
>
> total: 0 errors, 4 warnings, 0 checks, 343 lines checked
> d1464a87a5a8 drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion
> -:18: WARNING:TYPO_SPELLING: 'accomodate' may be misspelled - perhaps 'accommodate'?
> #18:
> -Modified the color-conversion cap helper function, to accomodate
>
> total: 0 errors, 1 warnings, 0 checks, 106 lines checked
> 29e16a799211 drm/i915: Capture max frl rate for PCON in dfp cap structure
> -:13: WARNING:COMMIT_LOG_LONG_LINE: Possible unwrapped commit description (prefer a maximum 75 chars per line)
> #13:
> -tweaked the comparison of target bw and pcon frl bw to avoid roundup errors.
>
> total: 0 errors, 1 warnings, 0 checks, 60 lines checked
> 0f68d7283295 drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
> -:86: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
> #86: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4005:
> +{
> +
>
> -:147: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
> #147: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4066:
> + wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) == true, TIMEOUT_FRL_READY_MS);
>
> -:166: WARNING:LONG_LINE: line length of 112 exceeds 100 columns
> #166: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4085:
> + wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux) == true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
>
> -:172: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
> #172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
> + if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
>
> -:172: WARNING:CONSTANT_COMPARISON: Comparisons should place the constant on the right side of the test
> #172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
> + if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
>
> -:176: WARNING:LONG_LINE: line length of 109 exceeds 100 columns
> #176: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4095:
> + drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK = %u\n", max_frl_bw_mask, frl_trained_mask);
>
> total: 0 errors, 5 warnings, 1 checks, 194 lines checked
> 3793f5252161 drm/i915: Check for FRL training before DP Link training
> 126578f6fe39 drm/i915: Add support for enabling link status and recovery
> -:54: WARNING:LONG_LINE: line length of 107 exceeds 100 columns
> #54: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6031:
> + drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux, &intel_dp->attached_connector->base);
>
> total: 0 errors, 1 warnings, 0 checks, 83 lines checked
> ca5d8df43ceb drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
> -:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
> #51: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4000:
> + if (drm_dp_dpcd_read(&intel_dp->aux, DP_PCON_DSC_ENCODER,
> + intel_dp->pcon_dsc_dpcd,
>
> -:57: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
> #57: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4006:
> + drm_dbg_kms(&i915->drm, "PCON ENCODER DSC DPCD: %*ph\n",
> + (int)sizeof(intel_dp->pcon_dsc_dpcd), intel_dp->pcon_dsc_dpcd);
>
> total: 0 errors, 0 warnings, 2 checks, 39 lines checked
> 35f69a655bad drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1
> -:57: WARNING:TYPO_SPELLING: 'capabilites' may be misspelled - perhaps 'capabilities'?
> #57: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3458:
> + * and dsc decoder capabilites
>
> -:143: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
> #143: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3544:
> + if (min_slices <= 1 && src_max_slices >= 1 && hdmi_max_slices >= 1)
> + target_slices = 1;
>
> -:145: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
> #145: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3546:
> + else if (min_slices <= 2 && src_max_slices >= 2 && hdmi_max_slices >= 2)
> + target_slices = 2;
>
> -:147: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
> #147: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3548:
> + else if (min_slices <= 4 && src_max_slices >= 4 && hdmi_max_slices >= 4)
> + target_slices = 4;
>
> -:149: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
> #149: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3550:
> + else if (min_slices <= 8 && src_max_slices >= 8 && hdmi_max_slices >= 8)
> + target_slices = 8;
>
> -:151: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
> #151: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3552:
> + else if (min_slices <= 12 && src_max_slices >= 12 && hdmi_max_slices >= 12)
> + target_slices = 12;
>
> -:153: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
> #153: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3554:
> + else if (min_slices <= 16 && src_max_slices >= 16 && hdmi_max_slices >= 16)
> + target_slices = 16;
>
> total: 0 errors, 7 warnings, 0 checks, 248 lines checked
> 34ee9dfdadfd drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
> -:75: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
> #75: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4171:
> +{
> +
>
> -:92: CHECK:LINE_SPACING: Please don't use multiple blank lines
> #92: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4188:
> +
> +
>
> -:155: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
> #155: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4251:
> + bits_per_pixel = intel_dp_pcon_dsc_enc_bpp(intel_dp, crtc_state,
> + num_slices, slice_width);
>
> total: 0 errors, 0 warnings, 3 checks, 157 lines checked
> d739034947bb drm/i915/display: Let PCON convert from RGB to YCbCr if it can
> -:104: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
> #104: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4368:
> + DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
>
> -:156: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
> #156: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6922:
> + rgb_to_ycbcr = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
> + intel_dp->downstream_ports,
>
> total: 0 errors, 1 warnings, 1 checks, 152 lines checked
>
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-HDMI2.1 PCON (rev9)
2020-12-22 16:43 ` Jani Nikula
@ 2020-12-23 5:56 ` Nautiyal, Ankit K
2020-12-23 6:54 ` Shankar, Uma
0 siblings, 1 reply; 57+ messages in thread
From: Nautiyal, Ankit K @ 2020-12-23 5:56 UTC (permalink / raw)
To: Jani Nikula, swati2.sharma, uma.shankar; +Cc: intel-gfx
Hi Jani,
I apologize to miss these checkpatch errors. I mistakenly used some
older version of checkpatch script and couldn't get these.
Nevertheless I should have taken care of the warnings from the
patchwork. I fully understand that onus is on the submitter of the
series to fix all such warnings and checks, and I take full
responsibility of this mistake.
Thank you for fixing these issues this time, and I assure you that I
will take care in future and make sure that the checkpatch warnings are
addressed.
Once again I apologize for the fault.
Thanks & Regards,
Ankit
On 12/22/2020 10:13 PM, Jani Nikula wrote:
> On Fri, 18 Dec 2020, Patchwork <patchwork@emeril.freedesktop.org> wrote:
>> == Series Details ==
>>
>> Series: Add support for DP-HDMI2.1 PCON (rev9)
>> URL : https://patchwork.freedesktop.org/series/82098/
>> State : warning
>>
>> == Summary ==
>>
> All -
>
> I've fixed most of the checkpatch warnings (save for LONG_LINE and
> BIT_MACRO that we don't care so much about) while applying. It's not
> something I normally do, and I really don't want to find these when the
> series is at v7 and the same warnings have been there since September
> and I keep being pinged about merging.
>
> Keeping the driver nice and clean is your job too, not just mine.
>
> BR,
> Jani.
>
>
>> $ dim checkpatch origin/drm-tip
>> 26eb0c2f2ee1 drm/edid: Add additional HFVSDB fields for HDMI2.1
>> -:61: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-by: Sharma, Swati2 <swati2.sharma@intel.com>'
>>
>> total: 0 errors, 1 warnings, 0 checks, 36 lines checked
>> 13ffe829d77e drm/edid: Parse MAX_FRL field from HFVSDB block
>> -:73: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
>> #73: FILE: drivers/gpu/drm/drm_edid.c:4948:
>> + drm_get_max_frl_rate(max_frl_rate, &hdmi->max_lanes,
>> + &hdmi->max_frl_rate_per_lane);
>>
>> -:95: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-by: Sharma, Swati2 <swati2.sharma@intel.com>'
>>
>> total: 0 errors, 1 warnings, 1 checks, 68 lines checked
>> 89853c019e04 drm/edid: Parse DSC1.2 cap fields from HFVSDB block
>> -:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
>> #51: FILE: drivers/gpu/drm/drm_edid.c:4969:
>> + drm_get_max_frl_rate(dsc_max_frl_rate, &hdmi_dsc->max_lanes,
>> + &hdmi_dsc->max_frl_rate_per_lane);
>>
>> -:52: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>> #52: FILE: drivers/gpu/drm/drm_edid.c:4970:
>> + hdmi_dsc->total_chunk_kbytes = hf_vsdb[13] & DRM_EDID_DSC_TOTAL_CHUNK_KBYTES;
>>
>> total: 0 errors, 1 warnings, 1 checks, 125 lines checked
>> 5120b1727391 drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON
>> c68914ce7b67 drm/dp_helper: Add support for link failure detection
>> -:112: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
>> #112: FILE: include/drm/drm_dp_helper.h:2055:
>> +void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
>> + struct drm_connector *connector);
>>
>> total: 0 errors, 0 warnings, 1 checks, 76 lines checked
>> 2f4d3c12ee27 drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon
>> -:15: WARNING:TYPO_SPELLING: 'Convertor' may be misspelled - perhaps 'Converter'?
>> #15:
>> v3: Only setting the DSC bits for the Protocol Convertor control
>>
>> -:165: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */ on a separate line
>> #165: FILE: drivers/gpu/drm/drm_dp_helper.c:3037:
>> + * */
>>
>> -:185: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */ on a separate line
>> #185: FILE: drivers/gpu/drm/drm_dp_helper.c:3057:
>> + * */
>>
>> -:210: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */ on a separate line
>> #210: FILE: drivers/gpu/drm/drm_dp_helper.c:3082:
>> + * */
>>
>> total: 0 errors, 4 warnings, 0 checks, 343 lines checked
>> d1464a87a5a8 drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion
>> -:18: WARNING:TYPO_SPELLING: 'accomodate' may be misspelled - perhaps 'accommodate'?
>> #18:
>> -Modified the color-conversion cap helper function, to accomodate
>>
>> total: 0 errors, 1 warnings, 0 checks, 106 lines checked
>> 29e16a799211 drm/i915: Capture max frl rate for PCON in dfp cap structure
>> -:13: WARNING:COMMIT_LOG_LONG_LINE: Possible unwrapped commit description (prefer a maximum 75 chars per line)
>> #13:
>> -tweaked the comparison of target bw and pcon frl bw to avoid roundup errors.
>>
>> total: 0 errors, 1 warnings, 0 checks, 60 lines checked
>> 0f68d7283295 drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
>> -:86: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
>> #86: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4005:
>> +{
>> +
>>
>> -:147: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>> #147: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4066:
>> + wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) == true, TIMEOUT_FRL_READY_MS);
>>
>> -:166: WARNING:LONG_LINE: line length of 112 exceeds 100 columns
>> #166: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4085:
>> + wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux) == true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
>>
>> -:172: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>> #172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
>> + if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
>>
>> -:172: WARNING:CONSTANT_COMPARISON: Comparisons should place the constant on the right side of the test
>> #172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
>> + if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
>>
>> -:176: WARNING:LONG_LINE: line length of 109 exceeds 100 columns
>> #176: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4095:
>> + drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK = %u\n", max_frl_bw_mask, frl_trained_mask);
>>
>> total: 0 errors, 5 warnings, 1 checks, 194 lines checked
>> 3793f5252161 drm/i915: Check for FRL training before DP Link training
>> 126578f6fe39 drm/i915: Add support for enabling link status and recovery
>> -:54: WARNING:LONG_LINE: line length of 107 exceeds 100 columns
>> #54: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6031:
>> + drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux, &intel_dp->attached_connector->base);
>>
>> total: 0 errors, 1 warnings, 0 checks, 83 lines checked
>> ca5d8df43ceb drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
>> -:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
>> #51: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4000:
>> + if (drm_dp_dpcd_read(&intel_dp->aux, DP_PCON_DSC_ENCODER,
>> + intel_dp->pcon_dsc_dpcd,
>>
>> -:57: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
>> #57: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4006:
>> + drm_dbg_kms(&i915->drm, "PCON ENCODER DSC DPCD: %*ph\n",
>> + (int)sizeof(intel_dp->pcon_dsc_dpcd), intel_dp->pcon_dsc_dpcd);
>>
>> total: 0 errors, 0 warnings, 2 checks, 39 lines checked
>> 35f69a655bad drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1
>> -:57: WARNING:TYPO_SPELLING: 'capabilites' may be misspelled - perhaps 'capabilities'?
>> #57: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3458:
>> + * and dsc decoder capabilites
>>
>> -:143: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
>> #143: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3544:
>> + if (min_slices <= 1 && src_max_slices >= 1 && hdmi_max_slices >= 1)
>> + target_slices = 1;
>>
>> -:145: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
>> #145: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3546:
>> + else if (min_slices <= 2 && src_max_slices >= 2 && hdmi_max_slices >= 2)
>> + target_slices = 2;
>>
>> -:147: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
>> #147: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3548:
>> + else if (min_slices <= 4 && src_max_slices >= 4 && hdmi_max_slices >= 4)
>> + target_slices = 4;
>>
>> -:149: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
>> #149: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3550:
>> + else if (min_slices <= 8 && src_max_slices >= 8 && hdmi_max_slices >= 8)
>> + target_slices = 8;
>>
>> -:151: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
>> #151: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3552:
>> + else if (min_slices <= 12 && src_max_slices >= 12 && hdmi_max_slices >= 12)
>> + target_slices = 12;
>>
>> -:153: WARNING:SUSPECT_CODE_INDENT: suspect code indent for conditional statements (16, 23)
>> #153: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3554:
>> + else if (min_slices <= 16 && src_max_slices >= 16 && hdmi_max_slices >= 16)
>> + target_slices = 16;
>>
>> total: 0 errors, 7 warnings, 0 checks, 248 lines checked
>> 34ee9dfdadfd drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
>> -:75: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
>> #75: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4171:
>> +{
>> +
>>
>> -:92: CHECK:LINE_SPACING: Please don't use multiple blank lines
>> #92: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4188:
>> +
>> +
>>
>> -:155: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
>> #155: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4251:
>> + bits_per_pixel = intel_dp_pcon_dsc_enc_bpp(intel_dp, crtc_state,
>> + num_slices, slice_width);
>>
>> total: 0 errors, 0 warnings, 3 checks, 157 lines checked
>> d739034947bb drm/i915/display: Let PCON convert from RGB to YCbCr if it can
>> -:104: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>> #104: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4368:
>> + DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
>>
>> -:156: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
>> #156: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6922:
>> + rgb_to_ycbcr = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp->dpcd,
>> + intel_dp->downstream_ports,
>>
>> total: 0 errors, 1 warnings, 1 checks, 152 lines checked
>>
>>
>> _______________________________________________
>> Intel-gfx mailing list
>> Intel-gfx@lists.freedesktop.org
>> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-HDMI2.1 PCON (rev9)
2020-12-23 5:56 ` Nautiyal, Ankit K
@ 2020-12-23 6:54 ` Shankar, Uma
2020-12-23 7:08 ` Sharma, Swati2
0 siblings, 1 reply; 57+ messages in thread
From: Shankar, Uma @ 2020-12-23 6:54 UTC (permalink / raw)
To: Nautiyal, Ankit K, Jani Nikula, Sharma, Swati2; +Cc: intel-gfx
> -----Original Message-----
> From: Nautiyal, Ankit K <ankit.k.nautiyal@intel.com>
> Sent: Wednesday, December 23, 2020 11:27 AM
> To: Jani Nikula <jani.nikula@linux.intel.com>; Sharma, Swati2
> <swati2.sharma@intel.com>; Shankar, Uma <uma.shankar@intel.com>
> Cc: intel-gfx@lists.freedesktop.org
> Subject: Re: [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-
> HDMI2.1 PCON (rev9)
>
> Hi Jani,
>
> I apologize to miss these checkpatch errors. I mistakenly used some older version
> of checkpatch script and couldn't get these.
>
> Nevertheless I should have taken care of the warnings from the patchwork. I fully
> understand that onus is on the submitter of the series to fix all such warnings
> and checks, and I take full responsibility of this mistake.
>
> Thank you for fixing these issues this time, and I assure you that I will take care
> in future and make sure that the checkpatch warnings are addressed.
>
> Once again I apologize for the fault.
I also should have checked this, will be more careful to ensure this remains the top item
in the checklist along with CI results.
Regards,
Uma Shankar
>
> Thanks & Regards,
>
> Ankit
>
>
> On 12/22/2020 10:13 PM, Jani Nikula wrote:
> > On Fri, 18 Dec 2020, Patchwork <patchwork@emeril.freedesktop.org> wrote:
> >> == Series Details ==
> >>
> >> Series: Add support for DP-HDMI2.1 PCON (rev9)
> >> URL : https://patchwork.freedesktop.org/series/82098/
> >> State : warning
> >>
> >> == Summary ==
> >>
> > All -
> >
> > I've fixed most of the checkpatch warnings (save for LONG_LINE and
> > BIT_MACRO that we don't care so much about) while applying. It's not
> > something I normally do, and I really don't want to find these when
> > the series is at v7 and the same warnings have been there since
> > September and I keep being pinged about merging.
> >
> > Keeping the driver nice and clean is your job too, not just mine.
> >
> > BR,
> > Jani.
> >
> >
> >> $ dim checkpatch origin/drm-tip
> >> 26eb0c2f2ee1 drm/edid: Add additional HFVSDB fields for HDMI2.1
> >> -:61: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email
> name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-
> by: Sharma, Swati2 <swati2.sharma@intel.com>'
> >>
> >> total: 0 errors, 1 warnings, 0 checks, 36 lines checked 13ffe829d77e
> >> drm/edid: Parse MAX_FRL field from HFVSDB block
> >> -:73: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
> >> parenthesis
> >> #73: FILE: drivers/gpu/drm/drm_edid.c:4948:
> >> + drm_get_max_frl_rate(max_frl_rate, &hdmi->max_lanes,
> >> + &hdmi->max_frl_rate_per_lane);
> >>
> >> -:95: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email
> name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-
> by: Sharma, Swati2 <swati2.sharma@intel.com>'
> >>
> >> total: 0 errors, 1 warnings, 1 checks, 68 lines checked
> >> 89853c019e04 drm/edid: Parse DSC1.2 cap fields from HFVSDB block
> >> -:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
> >> parenthesis
> >> #51: FILE: drivers/gpu/drm/drm_edid.c:4969:
> >> + drm_get_max_frl_rate(dsc_max_frl_rate, &hdmi_dsc-
> >max_lanes,
> >> + &hdmi_dsc->max_frl_rate_per_lane);
> >>
> >> -:52: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
> >> #52: FILE: drivers/gpu/drm/drm_edid.c:4970:
> >> + hdmi_dsc->total_chunk_kbytes = hf_vsdb[13] &
> >> +DRM_EDID_DSC_TOTAL_CHUNK_KBYTES;
> >>
> >> total: 0 errors, 1 warnings, 1 checks, 125 lines checked
> >> 5120b1727391 drm/dp_helper: Add Helpers for FRL Link Training support
> >> for DP-HDMI2.1 PCON
> >> c68914ce7b67 drm/dp_helper: Add support for link failure detection
> >> -:112: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
> >> parenthesis
> >> #112: FILE: include/drm/drm_dp_helper.h:2055:
> >> +void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
> >> + struct drm_connector *connector);
> >>
> >> total: 0 errors, 0 warnings, 1 checks, 76 lines checked
> >> 2f4d3c12ee27 drm/dp_helper: Add support for Configuring DSC for
> >> HDMI2.1 Pcon
> >> -:15: WARNING:TYPO_SPELLING: 'Convertor' may be misspelled - perhaps
> 'Converter'?
> >> #15:
> >> v3: Only setting the DSC bits for the Protocol Convertor control
> >>
> >> -:165: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */
> >> on a separate line
> >> #165: FILE: drivers/gpu/drm/drm_dp_helper.c:3037:
> >> + * */
> >>
> >> -:185: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */
> >> on a separate line
> >> #185: FILE: drivers/gpu/drm/drm_dp_helper.c:3057:
> >> + * */
> >>
> >> -:210: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */
> >> on a separate line
> >> #210: FILE: drivers/gpu/drm/drm_dp_helper.c:3082:
> >> + * */
> >>
> >> total: 0 errors, 4 warnings, 0 checks, 343 lines checked
> >> d1464a87a5a8 drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr
> >> Conversion
> >> -:18: WARNING:TYPO_SPELLING: 'accomodate' may be misspelled - perhaps
> 'accommodate'?
> >> #18:
> >> -Modified the color-conversion cap helper function, to accomodate
> >>
> >> total: 0 errors, 1 warnings, 0 checks, 106 lines checked
> >> 29e16a799211 drm/i915: Capture max frl rate for PCON in dfp cap
> >> structure
> >> -:13: WARNING:COMMIT_LOG_LONG_LINE: Possible unwrapped commit
> >> description (prefer a maximum 75 chars per line)
> >> #13:
> >> -tweaked the comparison of target bw and pcon frl bw to avoid roundup
> errors.
> >>
> >> total: 0 errors, 1 warnings, 0 checks, 60 lines checked
> >> 0f68d7283295 drm/i915: Add support for starting FRL training for
> >> HDMI2.1 via PCON
> >> -:86: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
> >> #86: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4005:
> >> +{
> >> +
> >>
> >> -:147: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
> >> #147: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4066:
> >> + wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) ==
> >> +true, TIMEOUT_FRL_READY_MS);
> >>
> >> -:166: WARNING:LONG_LINE: line length of 112 exceeds 100 columns
> >> #166: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4085:
> >> + wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux)
> >> +== true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
> >>
> >> -:172: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
> >> #172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
> >> + if (DP_PCON_HDMI_MODE_FRL !=
> >> +drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
> >>
> >> -:172: WARNING:CONSTANT_COMPARISON: Comparisons should place the
> >> constant on the right side of the test
> >> #172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
> >> + if (DP_PCON_HDMI_MODE_FRL !=
> >> +drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
> >>
> >> -:176: WARNING:LONG_LINE: line length of 109 exceeds 100 columns
> >> #176: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4095:
> >> + drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK =
> %u\n",
> >> +max_frl_bw_mask, frl_trained_mask);
> >>
> >> total: 0 errors, 5 warnings, 1 checks, 194 lines checked
> >> 3793f5252161 drm/i915: Check for FRL training before DP Link training
> >> 126578f6fe39 drm/i915: Add support for enabling link status and
> >> recovery
> >> -:54: WARNING:LONG_LINE: line length of 107 exceeds 100 columns
> >> #54: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6031:
> >> + drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux,
> >> +&intel_dp->attached_connector->base);
> >>
> >> total: 0 errors, 1 warnings, 0 checks, 83 lines checked ca5d8df43ceb
> >> drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
> >> -:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
> >> parenthesis
> >> #51: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4000:
> >> + if (drm_dp_dpcd_read(&intel_dp->aux, DP_PCON_DSC_ENCODER,
> >> + intel_dp->pcon_dsc_dpcd,
> >>
> >> -:57: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
> >> parenthesis
> >> #57: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4006:
> >> + drm_dbg_kms(&i915->drm, "PCON ENCODER DSC DPCD: %*ph\n",
> >> + (int)sizeof(intel_dp->pcon_dsc_dpcd), intel_dp-
> >pcon_dsc_dpcd);
> >>
> >> total: 0 errors, 0 warnings, 2 checks, 39 lines checked 35f69a655bad
> >> drm/i915: Add helper functions for calculating DSC parameters for
> >> HDMI2.1
> >> -:57: WARNING:TYPO_SPELLING: 'capabilites' may be misspelled - perhaps
> 'capabilities'?
> >> #57: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3458:
> >> + * and dsc decoder capabilites
> >>
> >> -:143: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
> >> conditional statements (16, 23)
> >> #143: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3544:
> >> + if (min_slices <= 1 && src_max_slices >= 1 && hdmi_max_slices
> >= 1)
> >> + target_slices = 1;
> >>
> >> -:145: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
> >> conditional statements (16, 23)
> >> #145: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3546:
> >> + else if (min_slices <= 2 && src_max_slices >= 2 &&
> hdmi_max_slices >= 2)
> >> + target_slices = 2;
> >>
> >> -:147: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
> >> conditional statements (16, 23)
> >> #147: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3548:
> >> + else if (min_slices <= 4 && src_max_slices >= 4 &&
> hdmi_max_slices >= 4)
> >> + target_slices = 4;
> >>
> >> -:149: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
> >> conditional statements (16, 23)
> >> #149: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3550:
> >> + else if (min_slices <= 8 && src_max_slices >= 8 &&
> hdmi_max_slices >= 8)
> >> + target_slices = 8;
> >>
> >> -:151: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
> >> conditional statements (16, 23)
> >> #151: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3552:
> >> + else if (min_slices <= 12 && src_max_slices >= 12 &&
> hdmi_max_slices >= 12)
> >> + target_slices = 12;
> >>
> >> -:153: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
> >> conditional statements (16, 23)
> >> #153: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3554:
> >> + else if (min_slices <= 16 && src_max_slices >= 16 &&
> hdmi_max_slices >= 16)
> >> + target_slices = 16;
> >>
> >> total: 0 errors, 7 warnings, 0 checks, 248 lines checked 34ee9dfdadfd
> >> drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
> >> -:75: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
> >> #75: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4171:
> >> +{
> >> +
> >>
> >> -:92: CHECK:LINE_SPACING: Please don't use multiple blank lines
> >> #92: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4188:
> >> +
> >> +
> >>
> >> -:155: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
> >> parenthesis
> >> #155: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4251:
> >> + bits_per_pixel = intel_dp_pcon_dsc_enc_bpp(intel_dp, crtc_state,
> >> + num_slices, slice_width);
> >>
> >> total: 0 errors, 0 warnings, 3 checks, 157 lines checked d739034947bb
> >> drm/i915/display: Let PCON convert from RGB to YCbCr if it can
> >> -:104: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
> >> #104: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4368:
> >> +
> DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
> >>
> >> -:156: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
> >> parenthesis
> >> #156: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6922:
> >> + rgb_to_ycbcr = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp-
> >dpcd,
> >> + intel_dp-
> >downstream_ports,
> >>
> >> total: 0 errors, 1 warnings, 1 checks, 152 lines checked
> >>
> >>
> >> _______________________________________________
> >> Intel-gfx mailing list
> >> Intel-gfx@lists.freedesktop.org
> >> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-HDMI2.1 PCON (rev9)
2020-12-23 6:54 ` Shankar, Uma
@ 2020-12-23 7:08 ` Sharma, Swati2
2020-12-23 9:18 ` Jani Nikula
0 siblings, 1 reply; 57+ messages in thread
From: Sharma, Swati2 @ 2020-12-23 7:08 UTC (permalink / raw)
To: Shankar, Uma, Nautiyal, Ankit K, Jani Nikula; +Cc: intel-gfx
On 23-Dec-20 12:24 PM, Shankar, Uma wrote:
>
>
>> -----Original Message-----
>> From: Nautiyal, Ankit K <ankit.k.nautiyal@intel.com>
>> Sent: Wednesday, December 23, 2020 11:27 AM
>> To: Jani Nikula <jani.nikula@linux.intel.com>; Sharma, Swati2
>> <swati2.sharma@intel.com>; Shankar, Uma <uma.shankar@intel.com>
>> Cc: intel-gfx@lists.freedesktop.org
>> Subject: Re: [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-
>> HDMI2.1 PCON (rev9)
>>
>> Hi Jani,
>>
>> I apologize to miss these checkpatch errors. I mistakenly used some older version
>> of checkpatch script and couldn't get these.
>>
>> Nevertheless I should have taken care of the warnings from the patchwork. I fully
>> understand that onus is on the submitter of the series to fix all such warnings
>> and checks, and I take full responsibility of this mistake.
>>
>> Thank you for fixing these issues this time, and I assure you that I will take care
>> in future and make sure that the checkpatch warnings are addressed.
>>
>> Once again I apologize for the fault.
>
> I also should have checked this, will be more careful to ensure this remains the top item
> in the checklist along with CI results.
>
> Regards,
> Uma Shankar
Apologies from my side too.
Thanks and Regards,
Swati
>>
>> Thanks & Regards,
>>
>> Ankit
>>
>>
>> On 12/22/2020 10:13 PM, Jani Nikula wrote:
>>> On Fri, 18 Dec 2020, Patchwork <patchwork@emeril.freedesktop.org> wrote:
>>>> == Series Details ==
>>>>
>>>> Series: Add support for DP-HDMI2.1 PCON (rev9)
>>>> URL : https://patchwork.freedesktop.org/series/82098/
>>>> State : warning
>>>>
>>>> == Summary ==
>>>>
>>> All -
>>>
>>> I've fixed most of the checkpatch warnings (save for LONG_LINE and
>>> BIT_MACRO that we don't care so much about) while applying. It's not
>>> something I normally do, and I really don't want to find these when
>>> the series is at v7 and the same warnings have been there since
>>> September and I keep being pinged about merging.
>>>
>>> Keeping the driver nice and clean is your job too, not just mine.
>>>
>>> BR,
>>> Jani.
>>>
>>>
>>>> $ dim checkpatch origin/drm-tip
>>>> 26eb0c2f2ee1 drm/edid: Add additional HFVSDB fields for HDMI2.1
>>>> -:61: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email
>> name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-
>> by: Sharma, Swati2 <swati2.sharma@intel.com>'
>>>>
>>>> total: 0 errors, 1 warnings, 0 checks, 36 lines checked 13ffe829d77e
>>>> drm/edid: Parse MAX_FRL field from HFVSDB block
>>>> -:73: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>> parenthesis
>>>> #73: FILE: drivers/gpu/drm/drm_edid.c:4948:
>>>> + drm_get_max_frl_rate(max_frl_rate, &hdmi->max_lanes,
>>>> + &hdmi->max_frl_rate_per_lane);
>>>>
>>>> -:95: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email
>> name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-
>> by: Sharma, Swati2 <swati2.sharma@intel.com>'
>>>>
>>>> total: 0 errors, 1 warnings, 1 checks, 68 lines checked
>>>> 89853c019e04 drm/edid: Parse DSC1.2 cap fields from HFVSDB block
>>>> -:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>> parenthesis
>>>> #51: FILE: drivers/gpu/drm/drm_edid.c:4969:
>>>> + drm_get_max_frl_rate(dsc_max_frl_rate, &hdmi_dsc-
>>> max_lanes,
>>>> + &hdmi_dsc->max_frl_rate_per_lane);
>>>>
>>>> -:52: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>>>> #52: FILE: drivers/gpu/drm/drm_edid.c:4970:
>>>> + hdmi_dsc->total_chunk_kbytes = hf_vsdb[13] &
>>>> +DRM_EDID_DSC_TOTAL_CHUNK_KBYTES;
>>>>
>>>> total: 0 errors, 1 warnings, 1 checks, 125 lines checked
>>>> 5120b1727391 drm/dp_helper: Add Helpers for FRL Link Training support
>>>> for DP-HDMI2.1 PCON
>>>> c68914ce7b67 drm/dp_helper: Add support for link failure detection
>>>> -:112: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>> parenthesis
>>>> #112: FILE: include/drm/drm_dp_helper.h:2055:
>>>> +void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
>>>> + struct drm_connector *connector);
>>>>
>>>> total: 0 errors, 0 warnings, 1 checks, 76 lines checked
>>>> 2f4d3c12ee27 drm/dp_helper: Add support for Configuring DSC for
>>>> HDMI2.1 Pcon
>>>> -:15: WARNING:TYPO_SPELLING: 'Convertor' may be misspelled - perhaps
>> 'Converter'?
>>>> #15:
>>>> v3: Only setting the DSC bits for the Protocol Convertor control
>>>>
>>>> -:165: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */
>>>> on a separate line
>>>> #165: FILE: drivers/gpu/drm/drm_dp_helper.c:3037:
>>>> + * */
>>>>
>>>> -:185: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */
>>>> on a separate line
>>>> #185: FILE: drivers/gpu/drm/drm_dp_helper.c:3057:
>>>> + * */
>>>>
>>>> -:210: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */
>>>> on a separate line
>>>> #210: FILE: drivers/gpu/drm/drm_dp_helper.c:3082:
>>>> + * */
>>>>
>>>> total: 0 errors, 4 warnings, 0 checks, 343 lines checked
>>>> d1464a87a5a8 drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr
>>>> Conversion
>>>> -:18: WARNING:TYPO_SPELLING: 'accomodate' may be misspelled - perhaps
>> 'accommodate'?
>>>> #18:
>>>> -Modified the color-conversion cap helper function, to accomodate
>>>>
>>>> total: 0 errors, 1 warnings, 0 checks, 106 lines checked
>>>> 29e16a799211 drm/i915: Capture max frl rate for PCON in dfp cap
>>>> structure
>>>> -:13: WARNING:COMMIT_LOG_LONG_LINE: Possible unwrapped commit
>>>> description (prefer a maximum 75 chars per line)
>>>> #13:
>>>> -tweaked the comparison of target bw and pcon frl bw to avoid roundup
>> errors.
>>>>
>>>> total: 0 errors, 1 warnings, 0 checks, 60 lines checked
>>>> 0f68d7283295 drm/i915: Add support for starting FRL training for
>>>> HDMI2.1 via PCON
>>>> -:86: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
>>>> #86: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4005:
>>>> +{
>>>> +
>>>>
>>>> -:147: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>>>> #147: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4066:
>>>> + wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) ==
>>>> +true, TIMEOUT_FRL_READY_MS);
>>>>
>>>> -:166: WARNING:LONG_LINE: line length of 112 exceeds 100 columns
>>>> #166: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4085:
>>>> + wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux)
>>>> +== true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
>>>>
>>>> -:172: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>>>> #172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
>>>> + if (DP_PCON_HDMI_MODE_FRL !=
>>>> +drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
>>>>
>>>> -:172: WARNING:CONSTANT_COMPARISON: Comparisons should place the
>>>> constant on the right side of the test
>>>> #172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
>>>> + if (DP_PCON_HDMI_MODE_FRL !=
>>>> +drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
>>>>
>>>> -:176: WARNING:LONG_LINE: line length of 109 exceeds 100 columns
>>>> #176: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4095:
>>>> + drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK =
>> %u\n",
>>>> +max_frl_bw_mask, frl_trained_mask);
>>>>
>>>> total: 0 errors, 5 warnings, 1 checks, 194 lines checked
>>>> 3793f5252161 drm/i915: Check for FRL training before DP Link training
>>>> 126578f6fe39 drm/i915: Add support for enabling link status and
>>>> recovery
>>>> -:54: WARNING:LONG_LINE: line length of 107 exceeds 100 columns
>>>> #54: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6031:
>>>> + drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux,
>>>> +&intel_dp->attached_connector->base);
>>>>
>>>> total: 0 errors, 1 warnings, 0 checks, 83 lines checked ca5d8df43ceb
>>>> drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
>>>> -:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>> parenthesis
>>>> #51: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4000:
>>>> + if (drm_dp_dpcd_read(&intel_dp->aux, DP_PCON_DSC_ENCODER,
>>>> + intel_dp->pcon_dsc_dpcd,
>>>>
>>>> -:57: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>> parenthesis
>>>> #57: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4006:
>>>> + drm_dbg_kms(&i915->drm, "PCON ENCODER DSC DPCD: %*ph\n",
>>>> + (int)sizeof(intel_dp->pcon_dsc_dpcd), intel_dp-
>>> pcon_dsc_dpcd);
>>>>
>>>> total: 0 errors, 0 warnings, 2 checks, 39 lines checked 35f69a655bad
>>>> drm/i915: Add helper functions for calculating DSC parameters for
>>>> HDMI2.1
>>>> -:57: WARNING:TYPO_SPELLING: 'capabilites' may be misspelled - perhaps
>> 'capabilities'?
>>>> #57: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3458:
>>>> + * and dsc decoder capabilites
>>>>
>>>> -:143: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>> conditional statements (16, 23)
>>>> #143: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3544:
>>>> + if (min_slices <= 1 && src_max_slices >= 1 && hdmi_max_slices
>>> = 1)
>>>> + target_slices = 1;
>>>>
>>>> -:145: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>> conditional statements (16, 23)
>>>> #145: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3546:
>>>> + else if (min_slices <= 2 && src_max_slices >= 2 &&
>> hdmi_max_slices >= 2)
>>>> + target_slices = 2;
>>>>
>>>> -:147: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>> conditional statements (16, 23)
>>>> #147: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3548:
>>>> + else if (min_slices <= 4 && src_max_slices >= 4 &&
>> hdmi_max_slices >= 4)
>>>> + target_slices = 4;
>>>>
>>>> -:149: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>> conditional statements (16, 23)
>>>> #149: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3550:
>>>> + else if (min_slices <= 8 && src_max_slices >= 8 &&
>> hdmi_max_slices >= 8)
>>>> + target_slices = 8;
>>>>
>>>> -:151: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>> conditional statements (16, 23)
>>>> #151: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3552:
>>>> + else if (min_slices <= 12 && src_max_slices >= 12 &&
>> hdmi_max_slices >= 12)
>>>> + target_slices = 12;
>>>>
>>>> -:153: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>> conditional statements (16, 23)
>>>> #153: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3554:
>>>> + else if (min_slices <= 16 && src_max_slices >= 16 &&
>> hdmi_max_slices >= 16)
>>>> + target_slices = 16;
>>>>
>>>> total: 0 errors, 7 warnings, 0 checks, 248 lines checked 34ee9dfdadfd
>>>> drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
>>>> -:75: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
>>>> #75: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4171:
>>>> +{
>>>> +
>>>>
>>>> -:92: CHECK:LINE_SPACING: Please don't use multiple blank lines
>>>> #92: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4188:
>>>> +
>>>> +
>>>>
>>>> -:155: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>> parenthesis
>>>> #155: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4251:
>>>> + bits_per_pixel = intel_dp_pcon_dsc_enc_bpp(intel_dp, crtc_state,
>>>> + num_slices, slice_width);
>>>>
>>>> total: 0 errors, 0 warnings, 3 checks, 157 lines checked d739034947bb
>>>> drm/i915/display: Let PCON convert from RGB to YCbCr if it can
>>>> -:104: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>>>> #104: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4368:
>>>> +
>> DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
>>>>
>>>> -:156: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>> parenthesis
>>>> #156: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6922:
>>>> + rgb_to_ycbcr = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp-
>>> dpcd,
>>>> + intel_dp-
>>> downstream_ports,
>>>>
>>>> total: 0 errors, 1 warnings, 1 checks, 152 lines checked
>>>>
>>>>
>>>> _______________________________________________
>>>> Intel-gfx mailing list
>>>> Intel-gfx@lists.freedesktop.org
>>>> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
~Swati Sharma
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-HDMI2.1 PCON (rev9)
2020-12-23 7:08 ` Sharma, Swati2
@ 2020-12-23 9:18 ` Jani Nikula
0 siblings, 0 replies; 57+ messages in thread
From: Jani Nikula @ 2020-12-23 9:18 UTC (permalink / raw)
To: Sharma, Swati2, Shankar, Uma, Nautiyal, Ankit K; +Cc: intel-gfx
On Wed, 23 Dec 2020, "Sharma, Swati2" <swati2.sharma@intel.com> wrote:
> On 23-Dec-20 12:24 PM, Shankar, Uma wrote:
>>
>>
>>> -----Original Message-----
>>> From: Nautiyal, Ankit K <ankit.k.nautiyal@intel.com>
>>> Sent: Wednesday, December 23, 2020 11:27 AM
>>> To: Jani Nikula <jani.nikula@linux.intel.com>; Sharma, Swati2
>>> <swati2.sharma@intel.com>; Shankar, Uma <uma.shankar@intel.com>
>>> Cc: intel-gfx@lists.freedesktop.org
>>> Subject: Re: [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-
>>> HDMI2.1 PCON (rev9)
>>>
>>> Hi Jani,
>>>
>>> I apologize to miss these checkpatch errors. I mistakenly used some older version
>>> of checkpatch script and couldn't get these.
>>>
>>> Nevertheless I should have taken care of the warnings from the patchwork. I fully
>>> understand that onus is on the submitter of the series to fix all such warnings
>>> and checks, and I take full responsibility of this mistake.
>>>
>>> Thank you for fixing these issues this time, and I assure you that I will take care
>>> in future and make sure that the checkpatch warnings are addressed.
>>>
>>> Once again I apologize for the fault.
>>
>> I also should have checked this, will be more careful to ensure this remains the top item
>> in the checklist along with CI results.
>>
>> Regards,
>> Uma Shankar
>
> Apologies from my side too.
>
> Thanks and Regards,
> Swati
Hey -
Don't worry about it. I mean, do pay attention going forward, but don't
worry about it. ;)
Also, please consider using 'dim checkpatch' as a helper for checking
the commits in a branch. It'll use checkpatch from the kernel repo
directly, and it'll pass useful parameters to checkpatch. One of them is
--strict, which you may have missed.
For example, to check the HEAD commit:
$ dim checkpatch
Five topmost commits in your current branch:
$ dim checkpatch HEAD~5
Additionally use the "drm-intel" profile to filter out some of the more
noisy warnings we don't care so much about (*):
$ dim checkpatch HEAD~5 drm-intel
HTH,
Jani.
(*) --max-line-length=100 --ignore=BIT_MACRO,SPLIT_STRING,LONG_LINE_STRING,BOOL_MEMBER
>>>
>>> Thanks & Regards,
>>>
>>> Ankit
>>>
>>>
>>> On 12/22/2020 10:13 PM, Jani Nikula wrote:
>>>> On Fri, 18 Dec 2020, Patchwork <patchwork@emeril.freedesktop.org> wrote:
>>>>> == Series Details ==
>>>>>
>>>>> Series: Add support for DP-HDMI2.1 PCON (rev9)
>>>>> URL : https://patchwork.freedesktop.org/series/82098/
>>>>> State : warning
>>>>>
>>>>> == Summary ==
>>>>>
>>>> All -
>>>>
>>>> I've fixed most of the checkpatch warnings (save for LONG_LINE and
>>>> BIT_MACRO that we don't care so much about) while applying. It's not
>>>> something I normally do, and I really don't want to find these when
>>>> the series is at v7 and the same warnings have been there since
>>>> September and I keep being pinged about merging.
>>>>
>>>> Keeping the driver nice and clean is your job too, not just mine.
>>>>
>>>> BR,
>>>> Jani.
>>>>
>>>>
>>>>> $ dim checkpatch origin/drm-tip
>>>>> 26eb0c2f2ee1 drm/edid: Add additional HFVSDB fields for HDMI2.1
>>>>> -:61: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email
>>> name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-
>>> by: Sharma, Swati2 <swati2.sharma@intel.com>'
>>>>>
>>>>> total: 0 errors, 1 warnings, 0 checks, 36 lines checked 13ffe829d77e
>>>>> drm/edid: Parse MAX_FRL field from HFVSDB block
>>>>> -:73: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>>> parenthesis
>>>>> #73: FILE: drivers/gpu/drm/drm_edid.c:4948:
>>>>> + drm_get_max_frl_rate(max_frl_rate, &hdmi->max_lanes,
>>>>> + &hdmi->max_frl_rate_per_lane);
>>>>>
>>>>> -:95: WARNING:FROM_SIGN_OFF_MISMATCH: From:/Signed-off-by: email
>>> name mismatch: 'From: Swati Sharma <swati2.sharma@intel.com>' != 'Signed-off-
>>> by: Sharma, Swati2 <swati2.sharma@intel.com>'
>>>>>
>>>>> total: 0 errors, 1 warnings, 1 checks, 68 lines checked
>>>>> 89853c019e04 drm/edid: Parse DSC1.2 cap fields from HFVSDB block
>>>>> -:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>>> parenthesis
>>>>> #51: FILE: drivers/gpu/drm/drm_edid.c:4969:
>>>>> + drm_get_max_frl_rate(dsc_max_frl_rate, &hdmi_dsc-
>>>> max_lanes,
>>>>> + &hdmi_dsc->max_frl_rate_per_lane);
>>>>>
>>>>> -:52: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>>>>> #52: FILE: drivers/gpu/drm/drm_edid.c:4970:
>>>>> + hdmi_dsc->total_chunk_kbytes = hf_vsdb[13] &
>>>>> +DRM_EDID_DSC_TOTAL_CHUNK_KBYTES;
>>>>>
>>>>> total: 0 errors, 1 warnings, 1 checks, 125 lines checked
>>>>> 5120b1727391 drm/dp_helper: Add Helpers for FRL Link Training support
>>>>> for DP-HDMI2.1 PCON
>>>>> c68914ce7b67 drm/dp_helper: Add support for link failure detection
>>>>> -:112: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>>> parenthesis
>>>>> #112: FILE: include/drm/drm_dp_helper.h:2055:
>>>>> +void drm_dp_pcon_hdmi_frl_link_error_count(struct drm_dp_aux *aux,
>>>>> + struct drm_connector *connector);
>>>>>
>>>>> total: 0 errors, 0 warnings, 1 checks, 76 lines checked
>>>>> 2f4d3c12ee27 drm/dp_helper: Add support for Configuring DSC for
>>>>> HDMI2.1 Pcon
>>>>> -:15: WARNING:TYPO_SPELLING: 'Convertor' may be misspelled - perhaps
>>> 'Converter'?
>>>>> #15:
>>>>> v3: Only setting the DSC bits for the Protocol Convertor control
>>>>>
>>>>> -:165: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */
>>>>> on a separate line
>>>>> #165: FILE: drivers/gpu/drm/drm_dp_helper.c:3037:
>>>>> + * */
>>>>>
>>>>> -:185: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */
>>>>> on a separate line
>>>>> #185: FILE: drivers/gpu/drm/drm_dp_helper.c:3057:
>>>>> + * */
>>>>>
>>>>> -:210: WARNING:BLOCK_COMMENT_STYLE: Block comments use a trailing */
>>>>> on a separate line
>>>>> #210: FILE: drivers/gpu/drm/drm_dp_helper.c:3082:
>>>>> + * */
>>>>>
>>>>> total: 0 errors, 4 warnings, 0 checks, 343 lines checked
>>>>> d1464a87a5a8 drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr
>>>>> Conversion
>>>>> -:18: WARNING:TYPO_SPELLING: 'accomodate' may be misspelled - perhaps
>>> 'accommodate'?
>>>>> #18:
>>>>> -Modified the color-conversion cap helper function, to accomodate
>>>>>
>>>>> total: 0 errors, 1 warnings, 0 checks, 106 lines checked
>>>>> 29e16a799211 drm/i915: Capture max frl rate for PCON in dfp cap
>>>>> structure
>>>>> -:13: WARNING:COMMIT_LOG_LONG_LINE: Possible unwrapped commit
>>>>> description (prefer a maximum 75 chars per line)
>>>>> #13:
>>>>> -tweaked the comparison of target bw and pcon frl bw to avoid roundup
>>> errors.
>>>>>
>>>>> total: 0 errors, 1 warnings, 0 checks, 60 lines checked
>>>>> 0f68d7283295 drm/i915: Add support for starting FRL training for
>>>>> HDMI2.1 via PCON
>>>>> -:86: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
>>>>> #86: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4005:
>>>>> +{
>>>>> +
>>>>>
>>>>> -:147: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>>>>> #147: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4066:
>>>>> + wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) ==
>>>>> +true, TIMEOUT_FRL_READY_MS);
>>>>>
>>>>> -:166: WARNING:LONG_LINE: line length of 112 exceeds 100 columns
>>>>> #166: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4085:
>>>>> + wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux)
>>>>> +== true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
>>>>>
>>>>> -:172: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>>>>> #172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
>>>>> + if (DP_PCON_HDMI_MODE_FRL !=
>>>>> +drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
>>>>>
>>>>> -:172: WARNING:CONSTANT_COMPARISON: Comparisons should place the
>>>>> constant on the right side of the test
>>>>> #172: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4091:
>>>>> + if (DP_PCON_HDMI_MODE_FRL !=
>>>>> +drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
>>>>>
>>>>> -:176: WARNING:LONG_LINE: line length of 109 exceeds 100 columns
>>>>> #176: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4095:
>>>>> + drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK =
>>> %u\n",
>>>>> +max_frl_bw_mask, frl_trained_mask);
>>>>>
>>>>> total: 0 errors, 5 warnings, 1 checks, 194 lines checked
>>>>> 3793f5252161 drm/i915: Check for FRL training before DP Link training
>>>>> 126578f6fe39 drm/i915: Add support for enabling link status and
>>>>> recovery
>>>>> -:54: WARNING:LONG_LINE: line length of 107 exceeds 100 columns
>>>>> #54: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6031:
>>>>> + drm_dp_pcon_hdmi_frl_link_error_count(&intel_dp->aux,
>>>>> +&intel_dp->attached_connector->base);
>>>>>
>>>>> total: 0 errors, 1 warnings, 0 checks, 83 lines checked ca5d8df43ceb
>>>>> drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder
>>>>> -:51: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>>> parenthesis
>>>>> #51: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4000:
>>>>> + if (drm_dp_dpcd_read(&intel_dp->aux, DP_PCON_DSC_ENCODER,
>>>>> + intel_dp->pcon_dsc_dpcd,
>>>>>
>>>>> -:57: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>>> parenthesis
>>>>> #57: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4006:
>>>>> + drm_dbg_kms(&i915->drm, "PCON ENCODER DSC DPCD: %*ph\n",
>>>>> + (int)sizeof(intel_dp->pcon_dsc_dpcd), intel_dp-
>>>> pcon_dsc_dpcd);
>>>>>
>>>>> total: 0 errors, 0 warnings, 2 checks, 39 lines checked 35f69a655bad
>>>>> drm/i915: Add helper functions for calculating DSC parameters for
>>>>> HDMI2.1
>>>>> -:57: WARNING:TYPO_SPELLING: 'capabilites' may be misspelled - perhaps
>>> 'capabilities'?
>>>>> #57: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3458:
>>>>> + * and dsc decoder capabilites
>>>>>
>>>>> -:143: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>>> conditional statements (16, 23)
>>>>> #143: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3544:
>>>>> + if (min_slices <= 1 && src_max_slices >= 1 && hdmi_max_slices
>>>> = 1)
>>>>> + target_slices = 1;
>>>>>
>>>>> -:145: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>>> conditional statements (16, 23)
>>>>> #145: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3546:
>>>>> + else if (min_slices <= 2 && src_max_slices >= 2 &&
>>> hdmi_max_slices >= 2)
>>>>> + target_slices = 2;
>>>>>
>>>>> -:147: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>>> conditional statements (16, 23)
>>>>> #147: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3548:
>>>>> + else if (min_slices <= 4 && src_max_slices >= 4 &&
>>> hdmi_max_slices >= 4)
>>>>> + target_slices = 4;
>>>>>
>>>>> -:149: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>>> conditional statements (16, 23)
>>>>> #149: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3550:
>>>>> + else if (min_slices <= 8 && src_max_slices >= 8 &&
>>> hdmi_max_slices >= 8)
>>>>> + target_slices = 8;
>>>>>
>>>>> -:151: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>>> conditional statements (16, 23)
>>>>> #151: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3552:
>>>>> + else if (min_slices <= 12 && src_max_slices >= 12 &&
>>> hdmi_max_slices >= 12)
>>>>> + target_slices = 12;
>>>>>
>>>>> -:153: WARNING:SUSPECT_CODE_INDENT: suspect code indent for
>>>>> conditional statements (16, 23)
>>>>> #153: FILE: drivers/gpu/drm/i915/display/intel_hdmi.c:3554:
>>>>> + else if (min_slices <= 16 && src_max_slices >= 16 &&
>>> hdmi_max_slices >= 16)
>>>>> + target_slices = 16;
>>>>>
>>>>> total: 0 errors, 7 warnings, 0 checks, 248 lines checked 34ee9dfdadfd
>>>>> drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding
>>>>> -:75: CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
>>>>> #75: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4171:
>>>>> +{
>>>>> +
>>>>>
>>>>> -:92: CHECK:LINE_SPACING: Please don't use multiple blank lines
>>>>> #92: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4188:
>>>>> +
>>>>> +
>>>>>
>>>>> -:155: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>>> parenthesis
>>>>> #155: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4251:
>>>>> + bits_per_pixel = intel_dp_pcon_dsc_enc_bpp(intel_dp, crtc_state,
>>>>> + num_slices, slice_width);
>>>>>
>>>>> total: 0 errors, 0 warnings, 3 checks, 157 lines checked d739034947bb
>>>>> drm/i915/display: Let PCON convert from RGB to YCbCr if it can
>>>>> -:104: WARNING:LONG_LINE: line length of 101 exceeds 100 columns
>>>>> #104: FILE: drivers/gpu/drm/i915/display/intel_dp.c:4368:
>>>>> +
>>> DP_DS_HDMI_BT2020_RGB_YCBCR_CONV);
>>>>>
>>>>> -:156: CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open
>>>>> parenthesis
>>>>> #156: FILE: drivers/gpu/drm/i915/display/intel_dp.c:6922:
>>>>> + rgb_to_ycbcr = drm_dp_downstream_rgb_to_ycbcr_conversion(intel_dp-
>>>> dpcd,
>>>>> + intel_dp-
>>>> downstream_ports,
>>>>>
>>>>> total: 0 errors, 1 warnings, 1 checks, 152 lines checked
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Intel-gfx mailing list
>>>>> Intel-gfx@lists.freedesktop.org
>>>>> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
@ 2021-02-01 20:38 ` Ville Syrjälä
-1 siblings, 0 replies; 57+ messages in thread
From: Ville Syrjälä @ 2021-02-01 20:38 UTC (permalink / raw)
To: Ankit Nautiyal
Cc: swati2.sharma, airlied, intel-gfx, vandita.kulkarni, uma.shankar,
dri-devel
On Fri, Dec 18, 2020 at 04:07:17PM +0530, Ankit Nautiyal wrote:
> This patch adds functions to start FRL training for an HDMI2.1 sink,
> connected via a PCON as a DP branch device.
> This patch also adds a new structure for storing frl training related
> data, when FRL training is completed.
>
> v2: As suggested by Uma Shankar:
> -renamed couple of variables for better clarity
> -tweaked the macros used for correct semantics for true/false
> -fixed other styling issues.
>
> v3: Completed the TODO for condition for going to FRL mode.
> Modified the condition to determine the required FRL b/w
> based only on the Pcon and Sink's max FRL values.
> Moved the frl structure initialization to intel_dp_init_connector().
>
> v4: Fixed typo in initialization of frl structure.
>
> v5: Always use FRL if its possible, instead of enabling only for
> higher modes as done in v3.
>
> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
> ---
> .../drm/i915/display/intel_display_types.h | 7 +
> drivers/gpu/drm/i915/display/intel_dp.c | 151 ++++++++++++++++++
> drivers/gpu/drm/i915/display/intel_dp.h | 2 +
> 3 files changed, 160 insertions(+)
<snip>
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
> index 0596d6c24e73..43027a6d5e5e 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> @@ -3891,6 +3891,8 @@ static void intel_disable_dp(struct intel_atomic_state *state,
> intel_edp_backlight_off(old_conn_state);
> intel_dp_set_power(intel_dp, DP_SET_POWER_D3);
> intel_edp_panel_off(intel_dp);
> + intel_dp->frl.is_trained = false;
> + intel_dp->frl.trained_rate_gbps = 0;
This stuff looks rather misplaced (or missing from elsewhere). This code
doesn't even get executed on modern platforms.
<snip>
> +static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
> +{
> +#define PCON_EXTENDED_TRAIN_MODE (1 > 0)
> +#define PCON_CONCURRENT_MODE (1 > 0)
> +#define PCON_SEQUENTIAL_MODE !PCON_CONCURRENT_MODE
> +#define PCON_NORMAL_TRAIN_MODE !PCON_EXTENDED_TRAIN_MODE
All of that looks like nonsense. What is it supposed to do?
> +#define TIMEOUT_FRL_READY_MS 500
> +#define TIMEOUT_HDMI_LINK_ACTIVE_MS 1000
> +
> + struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> + int max_frl_bw, max_pcon_frl_bw, max_edid_frl_bw, ret;
> + u8 max_frl_bw_mask = 0, frl_trained_mask;
> + bool is_active;
> +
> + ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
> + if (ret < 0)
> + return ret;
> +
> + max_pcon_frl_bw = intel_dp->dfp.pcon_max_frl_bw;
> + drm_dbg(&i915->drm, "PCON max rate = %d Gbps\n", max_pcon_frl_bw);
> +
> + max_edid_frl_bw = intel_dp_hdmi_sink_max_frl(intel_dp);
> + drm_dbg(&i915->drm, "Sink max rate from EDID = %d Gbps\n", max_edid_frl_bw);
> +
> + max_frl_bw = min(max_edid_frl_bw, max_pcon_frl_bw);
> +
> + if (max_frl_bw <= 0)
> + return -EINVAL;
> +
> + ret = drm_dp_pcon_frl_prepare(&intel_dp->aux, false);
> + if (ret < 0)
> + return ret;
> + /* Wait for PCON to be FRL Ready */
> + wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) == true, TIMEOUT_FRL_READY_MS);
> +
> + if (!is_active)
> + return -ETIMEDOUT;
> +
> + max_frl_bw_mask = intel_dp_pcon_set_frl_mask(max_frl_bw);
> + ret = drm_dp_pcon_frl_configure_1(&intel_dp->aux, max_frl_bw, PCON_SEQUENTIAL_MODE);
> + if (ret < 0)
> + return ret;
> + ret = drm_dp_pcon_frl_configure_2(&intel_dp->aux, max_frl_bw_mask, PCON_NORMAL_TRAIN_MODE);
> + if (ret < 0)
> + return ret;
> + ret = drm_dp_pcon_frl_enable(&intel_dp->aux);
> + if (ret < 0)
> + return ret;
> + /*
> + * Wait for FRL to be completed
> + * Check if the HDMI Link is up and active.
> + */
> + wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux) == true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
> +
> + if (!is_active)
> + return -ETIMEDOUT;
> +
> + /* Verify HDMI Link configuration shows FRL Mode */
> + if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
> + drm_dbg(&i915->drm, "HDMI couldn't be trained in FRL Mode\n");
> + return -EINVAL;
> + }
> + drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK = %u\n", max_frl_bw_mask, frl_trained_mask);
> +
> + intel_dp->frl.trained_rate_gbps = intel_dp_pcon_get_frl_mask(frl_trained_mask);
> + intel_dp->frl.is_trained = true;
> + drm_dbg(&i915->drm, "FRL trained with : %d Gbps\n", intel_dp->frl.trained_rate_gbps);
> +
> + return 0;
> +}
> +
> +static bool intel_dp_is_hdmi_2_1_sink(struct intel_dp *intel_dp)
> +{
> + if (drm_dp_is_branch(intel_dp->dpcd) &&
> + intel_dp->has_hdmi_sink &&
> + intel_dp_hdmi_sink_max_frl(intel_dp) > 0)
> + return true;
> +
> + return false;
> +}
> +
> +void intel_dp_check_frl_training(struct intel_dp *intel_dp)
> +{
> + struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
> +
> + /* Always go for FRL training if supported */
> + if (!intel_dp_is_hdmi_2_1_sink(intel_dp) ||
> + intel_dp->frl.is_trained)
> + return;
> +
> + if (intel_dp_pcon_start_frl_training(intel_dp) < 0) {
> + int ret, mode;
> +
> + drm_dbg(&dev_priv->drm, "Couldnt set FRL mode, continuing with TMDS mode\n");
> + ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
> + mode = drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, NULL);
> +
> + if (ret < 0 || mode != DP_PCON_HDMI_MODE_TMDS)
> + drm_dbg(&dev_priv->drm, "Issue with PCON, cannot set TMDS mode\n");
> + } else {
> + drm_dbg(&dev_priv->drm, "FRL training Completed\n");
> + }
> +}
> +
> static void
> g4x_set_link_train(struct intel_dp *intel_dp,
> const struct intel_crtc_state *crtc_state,
> @@ -8210,6 +8358,9 @@ intel_dp_init_connector(struct intel_digital_port *dig_port,
> (temp & ~0xf) | 0xd);
> }
>
> + intel_dp->frl.is_trained = false;
> + intel_dp->frl.trained_rate_gbps = 0;
> +
> return true;
>
> fail:
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.h b/drivers/gpu/drm/i915/display/intel_dp.h
> index b871a09b6901..58b76a20459c 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.h
> +++ b/drivers/gpu/drm/i915/display/intel_dp.h
> @@ -144,4 +144,6 @@ bool intel_dp_initial_fastset_check(struct intel_encoder *encoder,
> void intel_dp_sync_state(struct intel_encoder *encoder,
> const struct intel_crtc_state *crtc_state);
>
> +void intel_dp_check_frl_training(struct intel_dp *intel_dp);
> +
> #endif /* __INTEL_DP_H__ */
> --
> 2.17.1
--
Ville Syrjälä
Intel
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
@ 2021-02-01 20:38 ` Ville Syrjälä
0 siblings, 0 replies; 57+ messages in thread
From: Ville Syrjälä @ 2021-02-01 20:38 UTC (permalink / raw)
To: Ankit Nautiyal; +Cc: airlied, intel-gfx, dri-devel
On Fri, Dec 18, 2020 at 04:07:17PM +0530, Ankit Nautiyal wrote:
> This patch adds functions to start FRL training for an HDMI2.1 sink,
> connected via a PCON as a DP branch device.
> This patch also adds a new structure for storing frl training related
> data, when FRL training is completed.
>
> v2: As suggested by Uma Shankar:
> -renamed couple of variables for better clarity
> -tweaked the macros used for correct semantics for true/false
> -fixed other styling issues.
>
> v3: Completed the TODO for condition for going to FRL mode.
> Modified the condition to determine the required FRL b/w
> based only on the Pcon and Sink's max FRL values.
> Moved the frl structure initialization to intel_dp_init_connector().
>
> v4: Fixed typo in initialization of frl structure.
>
> v5: Always use FRL if its possible, instead of enabling only for
> higher modes as done in v3.
>
> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
> ---
> .../drm/i915/display/intel_display_types.h | 7 +
> drivers/gpu/drm/i915/display/intel_dp.c | 151 ++++++++++++++++++
> drivers/gpu/drm/i915/display/intel_dp.h | 2 +
> 3 files changed, 160 insertions(+)
<snip>
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
> index 0596d6c24e73..43027a6d5e5e 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> @@ -3891,6 +3891,8 @@ static void intel_disable_dp(struct intel_atomic_state *state,
> intel_edp_backlight_off(old_conn_state);
> intel_dp_set_power(intel_dp, DP_SET_POWER_D3);
> intel_edp_panel_off(intel_dp);
> + intel_dp->frl.is_trained = false;
> + intel_dp->frl.trained_rate_gbps = 0;
This stuff looks rather misplaced (or missing from elsewhere). This code
doesn't even get executed on modern platforms.
<snip>
> +static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
> +{
> +#define PCON_EXTENDED_TRAIN_MODE (1 > 0)
> +#define PCON_CONCURRENT_MODE (1 > 0)
> +#define PCON_SEQUENTIAL_MODE !PCON_CONCURRENT_MODE
> +#define PCON_NORMAL_TRAIN_MODE !PCON_EXTENDED_TRAIN_MODE
All of that looks like nonsense. What is it supposed to do?
> +#define TIMEOUT_FRL_READY_MS 500
> +#define TIMEOUT_HDMI_LINK_ACTIVE_MS 1000
> +
> + struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> + int max_frl_bw, max_pcon_frl_bw, max_edid_frl_bw, ret;
> + u8 max_frl_bw_mask = 0, frl_trained_mask;
> + bool is_active;
> +
> + ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
> + if (ret < 0)
> + return ret;
> +
> + max_pcon_frl_bw = intel_dp->dfp.pcon_max_frl_bw;
> + drm_dbg(&i915->drm, "PCON max rate = %d Gbps\n", max_pcon_frl_bw);
> +
> + max_edid_frl_bw = intel_dp_hdmi_sink_max_frl(intel_dp);
> + drm_dbg(&i915->drm, "Sink max rate from EDID = %d Gbps\n", max_edid_frl_bw);
> +
> + max_frl_bw = min(max_edid_frl_bw, max_pcon_frl_bw);
> +
> + if (max_frl_bw <= 0)
> + return -EINVAL;
> +
> + ret = drm_dp_pcon_frl_prepare(&intel_dp->aux, false);
> + if (ret < 0)
> + return ret;
> + /* Wait for PCON to be FRL Ready */
> + wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) == true, TIMEOUT_FRL_READY_MS);
> +
> + if (!is_active)
> + return -ETIMEDOUT;
> +
> + max_frl_bw_mask = intel_dp_pcon_set_frl_mask(max_frl_bw);
> + ret = drm_dp_pcon_frl_configure_1(&intel_dp->aux, max_frl_bw, PCON_SEQUENTIAL_MODE);
> + if (ret < 0)
> + return ret;
> + ret = drm_dp_pcon_frl_configure_2(&intel_dp->aux, max_frl_bw_mask, PCON_NORMAL_TRAIN_MODE);
> + if (ret < 0)
> + return ret;
> + ret = drm_dp_pcon_frl_enable(&intel_dp->aux);
> + if (ret < 0)
> + return ret;
> + /*
> + * Wait for FRL to be completed
> + * Check if the HDMI Link is up and active.
> + */
> + wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux) == true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
> +
> + if (!is_active)
> + return -ETIMEDOUT;
> +
> + /* Verify HDMI Link configuration shows FRL Mode */
> + if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
> + drm_dbg(&i915->drm, "HDMI couldn't be trained in FRL Mode\n");
> + return -EINVAL;
> + }
> + drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK = %u\n", max_frl_bw_mask, frl_trained_mask);
> +
> + intel_dp->frl.trained_rate_gbps = intel_dp_pcon_get_frl_mask(frl_trained_mask);
> + intel_dp->frl.is_trained = true;
> + drm_dbg(&i915->drm, "FRL trained with : %d Gbps\n", intel_dp->frl.trained_rate_gbps);
> +
> + return 0;
> +}
> +
> +static bool intel_dp_is_hdmi_2_1_sink(struct intel_dp *intel_dp)
> +{
> + if (drm_dp_is_branch(intel_dp->dpcd) &&
> + intel_dp->has_hdmi_sink &&
> + intel_dp_hdmi_sink_max_frl(intel_dp) > 0)
> + return true;
> +
> + return false;
> +}
> +
> +void intel_dp_check_frl_training(struct intel_dp *intel_dp)
> +{
> + struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
> +
> + /* Always go for FRL training if supported */
> + if (!intel_dp_is_hdmi_2_1_sink(intel_dp) ||
> + intel_dp->frl.is_trained)
> + return;
> +
> + if (intel_dp_pcon_start_frl_training(intel_dp) < 0) {
> + int ret, mode;
> +
> + drm_dbg(&dev_priv->drm, "Couldnt set FRL mode, continuing with TMDS mode\n");
> + ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
> + mode = drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, NULL);
> +
> + if (ret < 0 || mode != DP_PCON_HDMI_MODE_TMDS)
> + drm_dbg(&dev_priv->drm, "Issue with PCON, cannot set TMDS mode\n");
> + } else {
> + drm_dbg(&dev_priv->drm, "FRL training Completed\n");
> + }
> +}
> +
> static void
> g4x_set_link_train(struct intel_dp *intel_dp,
> const struct intel_crtc_state *crtc_state,
> @@ -8210,6 +8358,9 @@ intel_dp_init_connector(struct intel_digital_port *dig_port,
> (temp & ~0xf) | 0xd);
> }
>
> + intel_dp->frl.is_trained = false;
> + intel_dp->frl.trained_rate_gbps = 0;
> +
> return true;
>
> fail:
> diff --git a/drivers/gpu/drm/i915/display/intel_dp.h b/drivers/gpu/drm/i915/display/intel_dp.h
> index b871a09b6901..58b76a20459c 100644
> --- a/drivers/gpu/drm/i915/display/intel_dp.h
> +++ b/drivers/gpu/drm/i915/display/intel_dp.h
> @@ -144,4 +144,6 @@ bool intel_dp_initial_fastset_check(struct intel_encoder *encoder,
> void intel_dp_sync_state(struct intel_encoder *encoder,
> const struct intel_crtc_state *crtc_state);
>
> +void intel_dp_check_frl_training(struct intel_dp *intel_dp);
> +
> #endif /* __INTEL_DP_H__ */
> --
> 2.17.1
--
Ville Syrjälä
Intel
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
2021-02-01 20:38 ` [Intel-gfx] " Ville Syrjälä
@ 2021-02-02 6:39 ` Nautiyal, Ankit K
-1 siblings, 0 replies; 57+ messages in thread
From: Nautiyal, Ankit K @ 2021-02-02 6:39 UTC (permalink / raw)
To: Ville Syrjälä
Cc: swati2.sharma, airlied, intel-gfx, vandita.kulkarni, uma.shankar,
dri-devel
Hi Ville,
Please find my responses inline.
On 2/2/2021 2:08 AM, Ville Syrjälä wrote:
> On Fri, Dec 18, 2020 at 04:07:17PM +0530, Ankit Nautiyal wrote:
>> This patch adds functions to start FRL training for an HDMI2.1 sink,
>> connected via a PCON as a DP branch device.
>> This patch also adds a new structure for storing frl training related
>> data, when FRL training is completed.
>>
>> v2: As suggested by Uma Shankar:
>> -renamed couple of variables for better clarity
>> -tweaked the macros used for correct semantics for true/false
>> -fixed other styling issues.
>>
>> v3: Completed the TODO for condition for going to FRL mode.
>> Modified the condition to determine the required FRL b/w
>> based only on the Pcon and Sink's max FRL values.
>> Moved the frl structure initialization to intel_dp_init_connector().
>>
>> v4: Fixed typo in initialization of frl structure.
>>
>> v5: Always use FRL if its possible, instead of enabling only for
>> higher modes as done in v3.
>>
>> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
>> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
>> ---
>> .../drm/i915/display/intel_display_types.h | 7 +
>> drivers/gpu/drm/i915/display/intel_dp.c | 151 ++++++++++++++++++
>> drivers/gpu/drm/i915/display/intel_dp.h | 2 +
>> 3 files changed, 160 insertions(+)
> <snip>
>> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
>> index 0596d6c24e73..43027a6d5e5e 100644
>> --- a/drivers/gpu/drm/i915/display/intel_dp.c
>> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
>> @@ -3891,6 +3891,8 @@ static void intel_disable_dp(struct intel_atomic_state *state,
>> intel_edp_backlight_off(old_conn_state);
>> intel_dp_set_power(intel_dp, DP_SET_POWER_D3);
>> intel_edp_panel_off(intel_dp);
>> + intel_dp->frl.is_trained = false;
>> + intel_dp->frl.trained_rate_gbps = 0;
> This stuff looks rather misplaced (or missing from elsewhere). This code
> doesn't even get executed on modern platforms.
I think these two lines should have been added to
intel_ddi_post_disable_dp() for TGL+
My intention was to reset these before disabling DP. In hindsight, since
we are initializing (resetting) these in dp_init_connector, this doesnt
seem to be required.
I will send a patch to remove these two lines from here.
>
> <snip>
>> +static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
>> +{
>> +#define PCON_EXTENDED_TRAIN_MODE (1 > 0)
>> +#define PCON_CONCURRENT_MODE (1 > 0)
>> +#define PCON_SEQUENTIAL_MODE !PCON_CONCURRENT_MODE
>> +#define PCON_NORMAL_TRAIN_MODE !PCON_EXTENDED_TRAIN_MODE
> All of that looks like nonsense. What is it supposed to do?
When asking an HDMI2.1 PCON to initiate FRL training there are 2 options:
Sequential/Concurrent mode: Sequential mode attempts the FRL training
after DP Link training is completed. Concurrent mode tries to do the FRL
training, during DP link training.
Normal train Mode/ Extended mode: Normal train mode, PCON FW trains FRL
from Max to min BW, set by source in BW Mask. It aborts on first
successful training. In Extended mode, PCON FW trains for all BW set by
source in BW mask.
For Concurrent and Extended mode we need to set some extra bits in PCON
FRL config DPCDs
The intention was to go with sequential and Normal training mode, so no
need to set above bits.
Do you think, some documentation will make this clear?
Thanks & Regards,
Ankit
>
>> +#define TIMEOUT_FRL_READY_MS 500
>> +#define TIMEOUT_HDMI_LINK_ACTIVE_MS 1000
>> +
>> + struct drm_i915_private *i915 = dp_to_i915(intel_dp);
>> + int max_frl_bw, max_pcon_frl_bw, max_edid_frl_bw, ret;
>> + u8 max_frl_bw_mask = 0, frl_trained_mask;
>> + bool is_active;
>> +
>> + ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
>> + if (ret < 0)
>> + return ret;
>> +
>> + max_pcon_frl_bw = intel_dp->dfp.pcon_max_frl_bw;
>> + drm_dbg(&i915->drm, "PCON max rate = %d Gbps\n", max_pcon_frl_bw);
>> +
>> + max_edid_frl_bw = intel_dp_hdmi_sink_max_frl(intel_dp);
>> + drm_dbg(&i915->drm, "Sink max rate from EDID = %d Gbps\n", max_edid_frl_bw);
>> +
>> + max_frl_bw = min(max_edid_frl_bw, max_pcon_frl_bw);
>> +
>> + if (max_frl_bw <= 0)
>> + return -EINVAL;
>> +
>> + ret = drm_dp_pcon_frl_prepare(&intel_dp->aux, false);
>> + if (ret < 0)
>> + return ret;
>> + /* Wait for PCON to be FRL Ready */
>> + wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) == true, TIMEOUT_FRL_READY_MS);
>> +
>> + if (!is_active)
>> + return -ETIMEDOUT;
>> +
>> + max_frl_bw_mask = intel_dp_pcon_set_frl_mask(max_frl_bw);
>> + ret = drm_dp_pcon_frl_configure_1(&intel_dp->aux, max_frl_bw, PCON_SEQUENTIAL_MODE);
>> + if (ret < 0)
>> + return ret;
>> + ret = drm_dp_pcon_frl_configure_2(&intel_dp->aux, max_frl_bw_mask, PCON_NORMAL_TRAIN_MODE);
>> + if (ret < 0)
>> + return ret;
>> + ret = drm_dp_pcon_frl_enable(&intel_dp->aux);
>> + if (ret < 0)
>> + return ret;
>> + /*
>> + * Wait for FRL to be completed
>> + * Check if the HDMI Link is up and active.
>> + */
>> + wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux) == true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
>> +
>> + if (!is_active)
>> + return -ETIMEDOUT;
>> +
>> + /* Verify HDMI Link configuration shows FRL Mode */
>> + if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
>> + drm_dbg(&i915->drm, "HDMI couldn't be trained in FRL Mode\n");
>> + return -EINVAL;
>> + }
>> + drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK = %u\n", max_frl_bw_mask, frl_trained_mask);
>> +
>> + intel_dp->frl.trained_rate_gbps = intel_dp_pcon_get_frl_mask(frl_trained_mask);
>> + intel_dp->frl.is_trained = true;
>> + drm_dbg(&i915->drm, "FRL trained with : %d Gbps\n", intel_dp->frl.trained_rate_gbps);
>> +
>> + return 0;
>> +}
>> +
>> +static bool intel_dp_is_hdmi_2_1_sink(struct intel_dp *intel_dp)
>> +{
>> + if (drm_dp_is_branch(intel_dp->dpcd) &&
>> + intel_dp->has_hdmi_sink &&
>> + intel_dp_hdmi_sink_max_frl(intel_dp) > 0)
>> + return true;
>> +
>> + return false;
>> +}
>> +
>> +void intel_dp_check_frl_training(struct intel_dp *intel_dp)
>> +{
>> + struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
>> +
>> + /* Always go for FRL training if supported */
>> + if (!intel_dp_is_hdmi_2_1_sink(intel_dp) ||
>> + intel_dp->frl.is_trained)
>> + return;
>> +
>> + if (intel_dp_pcon_start_frl_training(intel_dp) < 0) {
>> + int ret, mode;
>> +
>> + drm_dbg(&dev_priv->drm, "Couldnt set FRL mode, continuing with TMDS mode\n");
>> + ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
>> + mode = drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, NULL);
>> +
>> + if (ret < 0 || mode != DP_PCON_HDMI_MODE_TMDS)
>> + drm_dbg(&dev_priv->drm, "Issue with PCON, cannot set TMDS mode\n");
>> + } else {
>> + drm_dbg(&dev_priv->drm, "FRL training Completed\n");
>> + }
>> +}
>> +
>> static void
>> g4x_set_link_train(struct intel_dp *intel_dp,
>> const struct intel_crtc_state *crtc_state,
>> @@ -8210,6 +8358,9 @@ intel_dp_init_connector(struct intel_digital_port *dig_port,
>> (temp & ~0xf) | 0xd);
>> }
>>
>> + intel_dp->frl.is_trained = false;
>> + intel_dp->frl.trained_rate_gbps = 0;
>> +
>> return true;
>>
>> fail:
>> diff --git a/drivers/gpu/drm/i915/display/intel_dp.h b/drivers/gpu/drm/i915/display/intel_dp.h
>> index b871a09b6901..58b76a20459c 100644
>> --- a/drivers/gpu/drm/i915/display/intel_dp.h
>> +++ b/drivers/gpu/drm/i915/display/intel_dp.h
>> @@ -144,4 +144,6 @@ bool intel_dp_initial_fastset_check(struct intel_encoder *encoder,
>> void intel_dp_sync_state(struct intel_encoder *encoder,
>> const struct intel_crtc_state *crtc_state);
>>
>> +void intel_dp_check_frl_training(struct intel_dp *intel_dp);
>> +
>> #endif /* __INTEL_DP_H__ */
>> --
>> 2.17.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
@ 2021-02-02 6:39 ` Nautiyal, Ankit K
0 siblings, 0 replies; 57+ messages in thread
From: Nautiyal, Ankit K @ 2021-02-02 6:39 UTC (permalink / raw)
To: Ville Syrjälä; +Cc: airlied, intel-gfx, dri-devel
Hi Ville,
Please find my responses inline.
On 2/2/2021 2:08 AM, Ville Syrjälä wrote:
> On Fri, Dec 18, 2020 at 04:07:17PM +0530, Ankit Nautiyal wrote:
>> This patch adds functions to start FRL training for an HDMI2.1 sink,
>> connected via a PCON as a DP branch device.
>> This patch also adds a new structure for storing frl training related
>> data, when FRL training is completed.
>>
>> v2: As suggested by Uma Shankar:
>> -renamed couple of variables for better clarity
>> -tweaked the macros used for correct semantics for true/false
>> -fixed other styling issues.
>>
>> v3: Completed the TODO for condition for going to FRL mode.
>> Modified the condition to determine the required FRL b/w
>> based only on the Pcon and Sink's max FRL values.
>> Moved the frl structure initialization to intel_dp_init_connector().
>>
>> v4: Fixed typo in initialization of frl structure.
>>
>> v5: Always use FRL if its possible, instead of enabling only for
>> higher modes as done in v3.
>>
>> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
>> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
>> ---
>> .../drm/i915/display/intel_display_types.h | 7 +
>> drivers/gpu/drm/i915/display/intel_dp.c | 151 ++++++++++++++++++
>> drivers/gpu/drm/i915/display/intel_dp.h | 2 +
>> 3 files changed, 160 insertions(+)
> <snip>
>> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
>> index 0596d6c24e73..43027a6d5e5e 100644
>> --- a/drivers/gpu/drm/i915/display/intel_dp.c
>> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
>> @@ -3891,6 +3891,8 @@ static void intel_disable_dp(struct intel_atomic_state *state,
>> intel_edp_backlight_off(old_conn_state);
>> intel_dp_set_power(intel_dp, DP_SET_POWER_D3);
>> intel_edp_panel_off(intel_dp);
>> + intel_dp->frl.is_trained = false;
>> + intel_dp->frl.trained_rate_gbps = 0;
> This stuff looks rather misplaced (or missing from elsewhere). This code
> doesn't even get executed on modern platforms.
I think these two lines should have been added to
intel_ddi_post_disable_dp() for TGL+
My intention was to reset these before disabling DP. In hindsight, since
we are initializing (resetting) these in dp_init_connector, this doesnt
seem to be required.
I will send a patch to remove these two lines from here.
>
> <snip>
>> +static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
>> +{
>> +#define PCON_EXTENDED_TRAIN_MODE (1 > 0)
>> +#define PCON_CONCURRENT_MODE (1 > 0)
>> +#define PCON_SEQUENTIAL_MODE !PCON_CONCURRENT_MODE
>> +#define PCON_NORMAL_TRAIN_MODE !PCON_EXTENDED_TRAIN_MODE
> All of that looks like nonsense. What is it supposed to do?
When asking an HDMI2.1 PCON to initiate FRL training there are 2 options:
Sequential/Concurrent mode: Sequential mode attempts the FRL training
after DP Link training is completed. Concurrent mode tries to do the FRL
training, during DP link training.
Normal train Mode/ Extended mode: Normal train mode, PCON FW trains FRL
from Max to min BW, set by source in BW Mask. It aborts on first
successful training. In Extended mode, PCON FW trains for all BW set by
source in BW mask.
For Concurrent and Extended mode we need to set some extra bits in PCON
FRL config DPCDs
The intention was to go with sequential and Normal training mode, so no
need to set above bits.
Do you think, some documentation will make this clear?
Thanks & Regards,
Ankit
>
>> +#define TIMEOUT_FRL_READY_MS 500
>> +#define TIMEOUT_HDMI_LINK_ACTIVE_MS 1000
>> +
>> + struct drm_i915_private *i915 = dp_to_i915(intel_dp);
>> + int max_frl_bw, max_pcon_frl_bw, max_edid_frl_bw, ret;
>> + u8 max_frl_bw_mask = 0, frl_trained_mask;
>> + bool is_active;
>> +
>> + ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
>> + if (ret < 0)
>> + return ret;
>> +
>> + max_pcon_frl_bw = intel_dp->dfp.pcon_max_frl_bw;
>> + drm_dbg(&i915->drm, "PCON max rate = %d Gbps\n", max_pcon_frl_bw);
>> +
>> + max_edid_frl_bw = intel_dp_hdmi_sink_max_frl(intel_dp);
>> + drm_dbg(&i915->drm, "Sink max rate from EDID = %d Gbps\n", max_edid_frl_bw);
>> +
>> + max_frl_bw = min(max_edid_frl_bw, max_pcon_frl_bw);
>> +
>> + if (max_frl_bw <= 0)
>> + return -EINVAL;
>> +
>> + ret = drm_dp_pcon_frl_prepare(&intel_dp->aux, false);
>> + if (ret < 0)
>> + return ret;
>> + /* Wait for PCON to be FRL Ready */
>> + wait_for(is_active = drm_dp_pcon_is_frl_ready(&intel_dp->aux) == true, TIMEOUT_FRL_READY_MS);
>> +
>> + if (!is_active)
>> + return -ETIMEDOUT;
>> +
>> + max_frl_bw_mask = intel_dp_pcon_set_frl_mask(max_frl_bw);
>> + ret = drm_dp_pcon_frl_configure_1(&intel_dp->aux, max_frl_bw, PCON_SEQUENTIAL_MODE);
>> + if (ret < 0)
>> + return ret;
>> + ret = drm_dp_pcon_frl_configure_2(&intel_dp->aux, max_frl_bw_mask, PCON_NORMAL_TRAIN_MODE);
>> + if (ret < 0)
>> + return ret;
>> + ret = drm_dp_pcon_frl_enable(&intel_dp->aux);
>> + if (ret < 0)
>> + return ret;
>> + /*
>> + * Wait for FRL to be completed
>> + * Check if the HDMI Link is up and active.
>> + */
>> + wait_for(is_active = drm_dp_pcon_hdmi_link_active(&intel_dp->aux) == true, TIMEOUT_HDMI_LINK_ACTIVE_MS);
>> +
>> + if (!is_active)
>> + return -ETIMEDOUT;
>> +
>> + /* Verify HDMI Link configuration shows FRL Mode */
>> + if (DP_PCON_HDMI_MODE_FRL != drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, &frl_trained_mask)) {
>> + drm_dbg(&i915->drm, "HDMI couldn't be trained in FRL Mode\n");
>> + return -EINVAL;
>> + }
>> + drm_dbg(&i915->drm, "MAX_FRL_MASK = %u, FRL_TRAINED_MASK = %u\n", max_frl_bw_mask, frl_trained_mask);
>> +
>> + intel_dp->frl.trained_rate_gbps = intel_dp_pcon_get_frl_mask(frl_trained_mask);
>> + intel_dp->frl.is_trained = true;
>> + drm_dbg(&i915->drm, "FRL trained with : %d Gbps\n", intel_dp->frl.trained_rate_gbps);
>> +
>> + return 0;
>> +}
>> +
>> +static bool intel_dp_is_hdmi_2_1_sink(struct intel_dp *intel_dp)
>> +{
>> + if (drm_dp_is_branch(intel_dp->dpcd) &&
>> + intel_dp->has_hdmi_sink &&
>> + intel_dp_hdmi_sink_max_frl(intel_dp) > 0)
>> + return true;
>> +
>> + return false;
>> +}
>> +
>> +void intel_dp_check_frl_training(struct intel_dp *intel_dp)
>> +{
>> + struct drm_i915_private *dev_priv = dp_to_i915(intel_dp);
>> +
>> + /* Always go for FRL training if supported */
>> + if (!intel_dp_is_hdmi_2_1_sink(intel_dp) ||
>> + intel_dp->frl.is_trained)
>> + return;
>> +
>> + if (intel_dp_pcon_start_frl_training(intel_dp) < 0) {
>> + int ret, mode;
>> +
>> + drm_dbg(&dev_priv->drm, "Couldnt set FRL mode, continuing with TMDS mode\n");
>> + ret = drm_dp_pcon_reset_frl_config(&intel_dp->aux);
>> + mode = drm_dp_pcon_hdmi_link_mode(&intel_dp->aux, NULL);
>> +
>> + if (ret < 0 || mode != DP_PCON_HDMI_MODE_TMDS)
>> + drm_dbg(&dev_priv->drm, "Issue with PCON, cannot set TMDS mode\n");
>> + } else {
>> + drm_dbg(&dev_priv->drm, "FRL training Completed\n");
>> + }
>> +}
>> +
>> static void
>> g4x_set_link_train(struct intel_dp *intel_dp,
>> const struct intel_crtc_state *crtc_state,
>> @@ -8210,6 +8358,9 @@ intel_dp_init_connector(struct intel_digital_port *dig_port,
>> (temp & ~0xf) | 0xd);
>> }
>>
>> + intel_dp->frl.is_trained = false;
>> + intel_dp->frl.trained_rate_gbps = 0;
>> +
>> return true;
>>
>> fail:
>> diff --git a/drivers/gpu/drm/i915/display/intel_dp.h b/drivers/gpu/drm/i915/display/intel_dp.h
>> index b871a09b6901..58b76a20459c 100644
>> --- a/drivers/gpu/drm/i915/display/intel_dp.h
>> +++ b/drivers/gpu/drm/i915/display/intel_dp.h
>> @@ -144,4 +144,6 @@ bool intel_dp_initial_fastset_check(struct intel_encoder *encoder,
>> void intel_dp_sync_state(struct intel_encoder *encoder,
>> const struct intel_crtc_state *crtc_state);
>>
>> +void intel_dp_check_frl_training(struct intel_dp *intel_dp);
>> +
>> #endif /* __INTEL_DP_H__ */
>> --
>> 2.17.1
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
2021-02-02 6:39 ` [Intel-gfx] " Nautiyal, Ankit K
@ 2021-02-02 6:47 ` Ville Syrjälä
-1 siblings, 0 replies; 57+ messages in thread
From: Ville Syrjälä @ 2021-02-02 6:47 UTC (permalink / raw)
To: Nautiyal, Ankit K
Cc: swati2.sharma, airlied, intel-gfx, vandita.kulkarni, uma.shankar,
dri-devel
On Tue, Feb 02, 2021 at 12:09:47PM +0530, Nautiyal, Ankit K wrote:
> Hi Ville,
>
> Please find my responses inline.
>
> On 2/2/2021 2:08 AM, Ville Syrjälä wrote:
> > On Fri, Dec 18, 2020 at 04:07:17PM +0530, Ankit Nautiyal wrote:
> >> This patch adds functions to start FRL training for an HDMI2.1 sink,
> >> connected via a PCON as a DP branch device.
> >> This patch also adds a new structure for storing frl training related
> >> data, when FRL training is completed.
> >>
> >> v2: As suggested by Uma Shankar:
> >> -renamed couple of variables for better clarity
> >> -tweaked the macros used for correct semantics for true/false
> >> -fixed other styling issues.
> >>
> >> v3: Completed the TODO for condition for going to FRL mode.
> >> Modified the condition to determine the required FRL b/w
> >> based only on the Pcon and Sink's max FRL values.
> >> Moved the frl structure initialization to intel_dp_init_connector().
> >>
> >> v4: Fixed typo in initialization of frl structure.
> >>
> >> v5: Always use FRL if its possible, instead of enabling only for
> >> higher modes as done in v3.
> >>
> >> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
> >> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
> >> ---
> >> .../drm/i915/display/intel_display_types.h | 7 +
> >> drivers/gpu/drm/i915/display/intel_dp.c | 151 ++++++++++++++++++
> >> drivers/gpu/drm/i915/display/intel_dp.h | 2 +
> >> 3 files changed, 160 insertions(+)
> > <snip>
> >> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
> >> index 0596d6c24e73..43027a6d5e5e 100644
> >> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> >> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> >> @@ -3891,6 +3891,8 @@ static void intel_disable_dp(struct intel_atomic_state *state,
> >> intel_edp_backlight_off(old_conn_state);
> >> intel_dp_set_power(intel_dp, DP_SET_POWER_D3);
> >> intel_edp_panel_off(intel_dp);
> >> + intel_dp->frl.is_trained = false;
> >> + intel_dp->frl.trained_rate_gbps = 0;
> > This stuff looks rather misplaced (or missing from elsewhere). This code
> > doesn't even get executed on modern platforms.
>
> I think these two lines should have been added to
> intel_ddi_post_disable_dp() for TGL+
>
> My intention was to reset these before disabling DP. In hindsight, since
> we are initializing (resetting) these in dp_init_connector, this doesnt
> seem to be required.
>
> I will send a patch to remove these two lines from here.
>
>
> >
> > <snip>
> >> +static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
> >> +{
> >> +#define PCON_EXTENDED_TRAIN_MODE (1 > 0)
> >> +#define PCON_CONCURRENT_MODE (1 > 0)
> >> +#define PCON_SEQUENTIAL_MODE !PCON_CONCURRENT_MODE
> >> +#define PCON_NORMAL_TRAIN_MODE !PCON_EXTENDED_TRAIN_MODE
> > All of that looks like nonsense. What is it supposed to do?
>
> When asking an HDMI2.1 PCON to initiate FRL training there are 2 options:
>
> Sequential/Concurrent mode: Sequential mode attempts the FRL training
> after DP Link training is completed. Concurrent mode tries to do the FRL
> training, during DP link training.
>
> Normal train Mode/ Extended mode: Normal train mode, PCON FW trains FRL
> from Max to min BW, set by source in BW Mask. It aborts on first
> successful training. In Extended mode, PCON FW trains for all BW set by
> source in BW mask.
>
> For Concurrent and Extended mode we need to set some extra bits in PCON
> FRL config DPCDs
>
> The intention was to go with sequential and Normal training mode, so no
> need to set above bits.
>
> Do you think, some documentation will make this clear?
I'm asking why does the code do
#define PCON_EXTENDED_TRAIN_MODE true
#define PCON_CONCURRENT_MODE true
#define PCON_SEQUENTIAL_MODE false
#define PCON_NORMAL_TRAIN_MODE false
but in a very convoluted way?
--
Ville Syrjälä
Intel
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
@ 2021-02-02 6:47 ` Ville Syrjälä
0 siblings, 0 replies; 57+ messages in thread
From: Ville Syrjälä @ 2021-02-02 6:47 UTC (permalink / raw)
To: Nautiyal, Ankit K; +Cc: airlied, intel-gfx, dri-devel
On Tue, Feb 02, 2021 at 12:09:47PM +0530, Nautiyal, Ankit K wrote:
> Hi Ville,
>
> Please find my responses inline.
>
> On 2/2/2021 2:08 AM, Ville Syrjälä wrote:
> > On Fri, Dec 18, 2020 at 04:07:17PM +0530, Ankit Nautiyal wrote:
> >> This patch adds functions to start FRL training for an HDMI2.1 sink,
> >> connected via a PCON as a DP branch device.
> >> This patch also adds a new structure for storing frl training related
> >> data, when FRL training is completed.
> >>
> >> v2: As suggested by Uma Shankar:
> >> -renamed couple of variables for better clarity
> >> -tweaked the macros used for correct semantics for true/false
> >> -fixed other styling issues.
> >>
> >> v3: Completed the TODO for condition for going to FRL mode.
> >> Modified the condition to determine the required FRL b/w
> >> based only on the Pcon and Sink's max FRL values.
> >> Moved the frl structure initialization to intel_dp_init_connector().
> >>
> >> v4: Fixed typo in initialization of frl structure.
> >>
> >> v5: Always use FRL if its possible, instead of enabling only for
> >> higher modes as done in v3.
> >>
> >> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
> >> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
> >> ---
> >> .../drm/i915/display/intel_display_types.h | 7 +
> >> drivers/gpu/drm/i915/display/intel_dp.c | 151 ++++++++++++++++++
> >> drivers/gpu/drm/i915/display/intel_dp.h | 2 +
> >> 3 files changed, 160 insertions(+)
> > <snip>
> >> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
> >> index 0596d6c24e73..43027a6d5e5e 100644
> >> --- a/drivers/gpu/drm/i915/display/intel_dp.c
> >> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
> >> @@ -3891,6 +3891,8 @@ static void intel_disable_dp(struct intel_atomic_state *state,
> >> intel_edp_backlight_off(old_conn_state);
> >> intel_dp_set_power(intel_dp, DP_SET_POWER_D3);
> >> intel_edp_panel_off(intel_dp);
> >> + intel_dp->frl.is_trained = false;
> >> + intel_dp->frl.trained_rate_gbps = 0;
> > This stuff looks rather misplaced (or missing from elsewhere). This code
> > doesn't even get executed on modern platforms.
>
> I think these two lines should have been added to
> intel_ddi_post_disable_dp() for TGL+
>
> My intention was to reset these before disabling DP. In hindsight, since
> we are initializing (resetting) these in dp_init_connector, this doesnt
> seem to be required.
>
> I will send a patch to remove these two lines from here.
>
>
> >
> > <snip>
> >> +static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
> >> +{
> >> +#define PCON_EXTENDED_TRAIN_MODE (1 > 0)
> >> +#define PCON_CONCURRENT_MODE (1 > 0)
> >> +#define PCON_SEQUENTIAL_MODE !PCON_CONCURRENT_MODE
> >> +#define PCON_NORMAL_TRAIN_MODE !PCON_EXTENDED_TRAIN_MODE
> > All of that looks like nonsense. What is it supposed to do?
>
> When asking an HDMI2.1 PCON to initiate FRL training there are 2 options:
>
> Sequential/Concurrent mode: Sequential mode attempts the FRL training
> after DP Link training is completed. Concurrent mode tries to do the FRL
> training, during DP link training.
>
> Normal train Mode/ Extended mode: Normal train mode, PCON FW trains FRL
> from Max to min BW, set by source in BW Mask. It aborts on first
> successful training. In Extended mode, PCON FW trains for all BW set by
> source in BW mask.
>
> For Concurrent and Extended mode we need to set some extra bits in PCON
> FRL config DPCDs
>
> The intention was to go with sequential and Normal training mode, so no
> need to set above bits.
>
> Do you think, some documentation will make this clear?
I'm asking why does the code do
#define PCON_EXTENDED_TRAIN_MODE true
#define PCON_CONCURRENT_MODE true
#define PCON_SEQUENTIAL_MODE false
#define PCON_NORMAL_TRAIN_MODE false
but in a very convoluted way?
--
Ville Syrjälä
Intel
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
2021-02-02 6:47 ` [Intel-gfx] " Ville Syrjälä
@ 2021-02-02 8:11 ` Nautiyal, Ankit K
-1 siblings, 0 replies; 57+ messages in thread
From: Nautiyal, Ankit K @ 2021-02-02 8:11 UTC (permalink / raw)
To: Ville Syrjälä
Cc: swati2.sharma, airlied, intel-gfx, vandita.kulkarni, uma.shankar,
dri-devel
On 2/2/2021 12:17 PM, Ville Syrjälä wrote:
> On Tue, Feb 02, 2021 at 12:09:47PM +0530, Nautiyal, Ankit K wrote:
>> Hi Ville,
>>
>> Please find my responses inline.
>>
>> On 2/2/2021 2:08 AM, Ville Syrjälä wrote:
>>> On Fri, Dec 18, 2020 at 04:07:17PM +0530, Ankit Nautiyal wrote:
>>>> This patch adds functions to start FRL training for an HDMI2.1 sink,
>>>> connected via a PCON as a DP branch device.
>>>> This patch also adds a new structure for storing frl training related
>>>> data, when FRL training is completed.
>>>>
>>>> v2: As suggested by Uma Shankar:
>>>> -renamed couple of variables for better clarity
>>>> -tweaked the macros used for correct semantics for true/false
>>>> -fixed other styling issues.
>>>>
>>>> v3: Completed the TODO for condition for going to FRL mode.
>>>> Modified the condition to determine the required FRL b/w
>>>> based only on the Pcon and Sink's max FRL values.
>>>> Moved the frl structure initialization to intel_dp_init_connector().
>>>>
>>>> v4: Fixed typo in initialization of frl structure.
>>>>
>>>> v5: Always use FRL if its possible, instead of enabling only for
>>>> higher modes as done in v3.
>>>>
>>>> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
>>>> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
>>>> ---
>>>> .../drm/i915/display/intel_display_types.h | 7 +
>>>> drivers/gpu/drm/i915/display/intel_dp.c | 151 ++++++++++++++++++
>>>> drivers/gpu/drm/i915/display/intel_dp.h | 2 +
>>>> 3 files changed, 160 insertions(+)
>>> <snip>
>>>> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
>>>> index 0596d6c24e73..43027a6d5e5e 100644
>>>> --- a/drivers/gpu/drm/i915/display/intel_dp.c
>>>> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
>>>> @@ -3891,6 +3891,8 @@ static void intel_disable_dp(struct intel_atomic_state *state,
>>>> intel_edp_backlight_off(old_conn_state);
>>>> intel_dp_set_power(intel_dp, DP_SET_POWER_D3);
>>>> intel_edp_panel_off(intel_dp);
>>>> + intel_dp->frl.is_trained = false;
>>>> + intel_dp->frl.trained_rate_gbps = 0;
>>> This stuff looks rather misplaced (or missing from elsewhere). This code
>>> doesn't even get executed on modern platforms.
>> I think these two lines should have been added to
>> intel_ddi_post_disable_dp() for TGL+
>>
>> My intention was to reset these before disabling DP. In hindsight, since
>> we are initializing (resetting) these in dp_init_connector, this doesnt
>> seem to be required.
>>
>> I will send a patch to remove these two lines from here.
>>
>>
>>> <snip>
>>>> +static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
>>>> +{
>>>> +#define PCON_EXTENDED_TRAIN_MODE (1 > 0)
>>>> +#define PCON_CONCURRENT_MODE (1 > 0)
>>>> +#define PCON_SEQUENTIAL_MODE !PCON_CONCURRENT_MODE
>>>> +#define PCON_NORMAL_TRAIN_MODE !PCON_EXTENDED_TRAIN_MODE
>>> All of that looks like nonsense. What is it supposed to do?
>> When asking an HDMI2.1 PCON to initiate FRL training there are 2 options:
>>
>> Sequential/Concurrent mode: Sequential mode attempts the FRL training
>> after DP Link training is completed. Concurrent mode tries to do the FRL
>> training, during DP link training.
>>
>> Normal train Mode/ Extended mode: Normal train mode, PCON FW trains FRL
>> from Max to min BW, set by source in BW Mask. It aborts on first
>> successful training. In Extended mode, PCON FW trains for all BW set by
>> source in BW mask.
>>
>> For Concurrent and Extended mode we need to set some extra bits in PCON
>> FRL config DPCDs
>>
>> The intention was to go with sequential and Normal training mode, so no
>> need to set above bits.
>>
>> Do you think, some documentation will make this clear?
> I'm asking why does the code do
>
> #define PCON_EXTENDED_TRAIN_MODE true
> #define PCON_CONCURRENT_MODE true
> #define PCON_SEQUENTIAL_MODE false
> #define PCON_NORMAL_TRAIN_MODE false
>
> but in a very convoluted way?
Yes this doesnt seem to be very intuitive, I had earlier used simpler in
initial versions.
As discussed offline, I will avoid all this and perhaps add enums for
this in drm_dp_helper.
Thanks & Regards,
Ankit
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply [flat|nested] 57+ messages in thread
* Re: [Intel-gfx] [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON
@ 2021-02-02 8:11 ` Nautiyal, Ankit K
0 siblings, 0 replies; 57+ messages in thread
From: Nautiyal, Ankit K @ 2021-02-02 8:11 UTC (permalink / raw)
To: Ville Syrjälä; +Cc: airlied, intel-gfx, dri-devel
On 2/2/2021 12:17 PM, Ville Syrjälä wrote:
> On Tue, Feb 02, 2021 at 12:09:47PM +0530, Nautiyal, Ankit K wrote:
>> Hi Ville,
>>
>> Please find my responses inline.
>>
>> On 2/2/2021 2:08 AM, Ville Syrjälä wrote:
>>> On Fri, Dec 18, 2020 at 04:07:17PM +0530, Ankit Nautiyal wrote:
>>>> This patch adds functions to start FRL training for an HDMI2.1 sink,
>>>> connected via a PCON as a DP branch device.
>>>> This patch also adds a new structure for storing frl training related
>>>> data, when FRL training is completed.
>>>>
>>>> v2: As suggested by Uma Shankar:
>>>> -renamed couple of variables for better clarity
>>>> -tweaked the macros used for correct semantics for true/false
>>>> -fixed other styling issues.
>>>>
>>>> v3: Completed the TODO for condition for going to FRL mode.
>>>> Modified the condition to determine the required FRL b/w
>>>> based only on the Pcon and Sink's max FRL values.
>>>> Moved the frl structure initialization to intel_dp_init_connector().
>>>>
>>>> v4: Fixed typo in initialization of frl structure.
>>>>
>>>> v5: Always use FRL if its possible, instead of enabling only for
>>>> higher modes as done in v3.
>>>>
>>>> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
>>>> Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
>>>> ---
>>>> .../drm/i915/display/intel_display_types.h | 7 +
>>>> drivers/gpu/drm/i915/display/intel_dp.c | 151 ++++++++++++++++++
>>>> drivers/gpu/drm/i915/display/intel_dp.h | 2 +
>>>> 3 files changed, 160 insertions(+)
>>> <snip>
>>>> diff --git a/drivers/gpu/drm/i915/display/intel_dp.c b/drivers/gpu/drm/i915/display/intel_dp.c
>>>> index 0596d6c24e73..43027a6d5e5e 100644
>>>> --- a/drivers/gpu/drm/i915/display/intel_dp.c
>>>> +++ b/drivers/gpu/drm/i915/display/intel_dp.c
>>>> @@ -3891,6 +3891,8 @@ static void intel_disable_dp(struct intel_atomic_state *state,
>>>> intel_edp_backlight_off(old_conn_state);
>>>> intel_dp_set_power(intel_dp, DP_SET_POWER_D3);
>>>> intel_edp_panel_off(intel_dp);
>>>> + intel_dp->frl.is_trained = false;
>>>> + intel_dp->frl.trained_rate_gbps = 0;
>>> This stuff looks rather misplaced (or missing from elsewhere). This code
>>> doesn't even get executed on modern platforms.
>> I think these two lines should have been added to
>> intel_ddi_post_disable_dp() for TGL+
>>
>> My intention was to reset these before disabling DP. In hindsight, since
>> we are initializing (resetting) these in dp_init_connector, this doesnt
>> seem to be required.
>>
>> I will send a patch to remove these two lines from here.
>>
>>
>>> <snip>
>>>> +static int intel_dp_pcon_start_frl_training(struct intel_dp *intel_dp)
>>>> +{
>>>> +#define PCON_EXTENDED_TRAIN_MODE (1 > 0)
>>>> +#define PCON_CONCURRENT_MODE (1 > 0)
>>>> +#define PCON_SEQUENTIAL_MODE !PCON_CONCURRENT_MODE
>>>> +#define PCON_NORMAL_TRAIN_MODE !PCON_EXTENDED_TRAIN_MODE
>>> All of that looks like nonsense. What is it supposed to do?
>> When asking an HDMI2.1 PCON to initiate FRL training there are 2 options:
>>
>> Sequential/Concurrent mode: Sequential mode attempts the FRL training
>> after DP Link training is completed. Concurrent mode tries to do the FRL
>> training, during DP link training.
>>
>> Normal train Mode/ Extended mode: Normal train mode, PCON FW trains FRL
>> from Max to min BW, set by source in BW Mask. It aborts on first
>> successful training. In Extended mode, PCON FW trains for all BW set by
>> source in BW mask.
>>
>> For Concurrent and Extended mode we need to set some extra bits in PCON
>> FRL config DPCDs
>>
>> The intention was to go with sequential and Normal training mode, so no
>> need to set above bits.
>>
>> Do you think, some documentation will make this clear?
> I'm asking why does the code do
>
> #define PCON_EXTENDED_TRAIN_MODE true
> #define PCON_CONCURRENT_MODE true
> #define PCON_SEQUENTIAL_MODE false
> #define PCON_NORMAL_TRAIN_MODE false
>
> but in a very convoluted way?
Yes this doesnt seem to be very intuitive, I had earlier used simpler in
initial versions.
As discussed offline, I will avoid all this and perhaps add enums for
this in drm_dp_helper.
Thanks & Regards,
Ankit
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
^ permalink raw reply [flat|nested] 57+ messages in thread
end of thread, other threads:[~2021-02-02 8:11 UTC | newest]
Thread overview: 57+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-12-18 10:37 [PATCH v7 00/15] Add support for DP-HDMI2.1 PCON Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 01/15] drm/edid: Add additional HFVSDB fields for HDMI2.1 Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 02/15] drm/edid: Parse MAX_FRL field from HFVSDB block Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 03/15] drm/edid: Parse DSC1.2 cap fields " Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 04/15] drm/dp_helper: Add Helpers for FRL Link Training support for DP-HDMI2.1 PCON Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 11:05 ` Shankar, Uma
2020-12-18 11:05 ` [Intel-gfx] " Shankar, Uma
2020-12-18 10:37 ` [PATCH v7 05/15] drm/dp_helper: Add support for link failure detection Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 06/15] drm/dp_helper: Add support for Configuring DSC for HDMI2.1 Pcon Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 07/15] drm/dp_helper: Add helpers to configure PCONs RGB-YCbCr Conversion Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 08/15] drm/i915: Capture max frl rate for PCON in dfp cap structure Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 09/15] drm/i915: Add support for starting FRL training for HDMI2.1 via PCON Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2021-02-01 20:38 ` Ville Syrjälä
2021-02-01 20:38 ` [Intel-gfx] " Ville Syrjälä
2021-02-02 6:39 ` Nautiyal, Ankit K
2021-02-02 6:39 ` [Intel-gfx] " Nautiyal, Ankit K
2021-02-02 6:47 ` Ville Syrjälä
2021-02-02 6:47 ` [Intel-gfx] " Ville Syrjälä
2021-02-02 8:11 ` Nautiyal, Ankit K
2021-02-02 8:11 ` [Intel-gfx] " Nautiyal, Ankit K
2020-12-18 10:37 ` [PATCH v7 10/15] drm/i915: Check for FRL training before DP Link training Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 11/15] drm/i915: Add support for enabling link status and recovery Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 11:06 ` Shankar, Uma
2020-12-18 11:06 ` [Intel-gfx] " Shankar, Uma
2020-12-18 10:37 ` [PATCH v7 12/15] drm/i915: Read DSC capabilities of the HDMI2.1 PCON encoder Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 13/15] drm/i915: Add helper functions for calculating DSC parameters for HDMI2.1 Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 14/15] drm/i915/display: Configure PCON for DSC1.1 to DSC1.2 encoding Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 10:37 ` [PATCH v7 15/15] drm/i915/display: Let PCON convert from RGB to YCbCr if it can Ankit Nautiyal
2020-12-18 10:37 ` [Intel-gfx] " Ankit Nautiyal
2020-12-18 11:11 ` Shankar, Uma
2020-12-18 11:11 ` [Intel-gfx] " Shankar, Uma
2020-12-18 12:52 ` [Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for Add support for DP-HDMI2.1 PCON (rev9) Patchwork
2020-12-22 16:43 ` Jani Nikula
2020-12-23 5:56 ` Nautiyal, Ankit K
2020-12-23 6:54 ` Shankar, Uma
2020-12-23 7:08 ` Sharma, Swati2
2020-12-23 9:18 ` Jani Nikula
2020-12-18 12:55 ` [Intel-gfx] ✗ Fi.CI.SPARSE: " Patchwork
2020-12-18 13:21 ` [Intel-gfx] ✓ Fi.CI.BAT: success " Patchwork
2020-12-18 15:37 ` [Intel-gfx] ✓ Fi.CI.IGT: " Patchwork
2020-12-22 16:28 ` [PATCH v7 00/15] Add support for DP-HDMI2.1 PCON Jani Nikula
2020-12-22 16:28 ` [Intel-gfx] " Jani Nikula
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.