[PATCH v7 00/10] mhi: pci_generic: Misc improvements

[PATCH v7 00/10] mhi: pci_generic: Misc improvements

[Loic Poulain]

This series adjust some configuration values to ensure stability and
robustness of mhi pci devices (timeout, number of events, burst mode).

It also includes support for system sleep as well as a recovery procedure
that can be triggered when a PCI error is reported, either by PCI AER or by
the new health-check mechanism.

All these changes have been tested with Telit FN980m module

v2:
  - Cancel recovery work on suspend
v3:
  - enable doorbell_mode_switch for burst channel (HW)
  - Add mhi_initialize_controller helper patch
v4:
  - Delete hard reset on module unload, MHI reset is enough (Jeffrey)
  - Move soc reset support in MHI core (Jeffrey)
  - burst mode: enable doorbell_mode_switch for HW channels (Bhaumik)
  - Add diag channels
v5:
  - Remove useless call to mhi_initialize_controller in alloc_controller (hemant)
  - Add define for post reset timeout (hemant)
  - Fix static misses (hemant)
v6:
  - Add debug print in case of recovery success (Mani)
  - Return error code in case of resume failure (Mani)
v7:
  - Removed mhi_initialize_controller API (Mani)
  - Added controller specific reset callback (Mani)
  - Reworked error handling using reset_prepare/done (Mani)

Loic Poulain (10):
  bus: mhi: core: Add device hardware reset support
  mhi: pci-generic: Increase number of hardware events
  mhi: pci_generic: Enable burst mode for hardware channels
  mhi: pci_generic: Add support for reset
  mhi: pci_generic: Add suspend/resume/recovery procedure
  mhi: pci_generic: Add PCI error handlers
  mhi: pci_generic: Add health-check
  mhi: pci_generic: Increase controller timeout value
  mhi: pci_generic: Add diag channels
  mhi: pci_generic: Set irq moderation value to 1ms for hw channels

 drivers/bus/mhi/core/main.c   |  13 ++
 drivers/bus/mhi/pci_generic.c | 359 +++++++++++++++++++++++++++++++++++++++---
 include/linux/mhi.h           |   9 ++
 3 files changed, 361 insertions(+), 20 deletions(-)

-- 
2.7.4

[PATCH v7 01/10] bus: mhi: core: Add device hardware reset support

[Loic Poulain]

The MHI specification allows to perform a hard reset of the device
when writing to the SOC_RESET register. It can be used to completely
restart the device (e.g. in case of unrecoverable MHI error).

This is up to the MHI controller driver to determine when this hard
reset should be used, and in case of MHI errors, should be used as
a reset of last resort (after standard MHI stack reset).

This function is a stateless function, the MHI layer do nothing except
triggering the reset by writing into the right register(s), this is up
to the caller to ensure right mhi_controller state (e.g. unregister the
controller if necessary).

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
---
 drivers/bus/mhi/core/main.c | 13 +++++++++++++
 include/linux/mhi.h         |  9 +++++++++
 2 files changed, 22 insertions(+)

diff --git a/drivers/bus/mhi/core/main.c b/drivers/bus/mhi/core/main.c
index a353d1e..c181a85 100644
--- a/drivers/bus/mhi/core/main.c
+++ b/drivers/bus/mhi/core/main.c
@@ -142,6 +142,19 @@ enum mhi_state mhi_get_mhi_state(struct mhi_controller *mhi_cntrl)
 }
 EXPORT_SYMBOL_GPL(mhi_get_mhi_state);
 
+void mhi_soc_reset(struct mhi_controller *mhi_cntrl)
+{
+	if (mhi_cntrl->reset) {
+		mhi_cntrl->reset(mhi_cntrl);
+		return;
+	}
+
+	/* Generic MHI SoC reset */
+	mhi_write_reg(mhi_cntrl, mhi_cntrl->regs, MHI_SOC_RESET_REQ_OFFSET,
+		      MHI_SOC_RESET_REQ);
+}
+EXPORT_SYMBOL_GPL(mhi_soc_reset);
+
 int mhi_map_single_no_bb(struct mhi_controller *mhi_cntrl,
 			 struct mhi_buf_info *buf_info)
 {
diff --git a/include/linux/mhi.h b/include/linux/mhi.h
index 04cf7f3..7ddbcd7 100644
--- a/include/linux/mhi.h
+++ b/include/linux/mhi.h
@@ -355,6 +355,7 @@ struct mhi_controller_config {
  * @unmap_single: CB function to destroy TRE buffer
  * @read_reg: Read a MHI register via the physical link (required)
  * @write_reg: Write a MHI register via the physical link (required)
+ * @reset: Controller specific reset function (optional)
  * @buffer_len: Bounce buffer length
  * @index: Index of the MHI controller instance
  * @bounce_buf: Use of bounce buffer
@@ -445,6 +446,7 @@ struct mhi_controller {
 			u32 *out);
 	void (*write_reg)(struct mhi_controller *mhi_cntrl, void __iomem *addr,
 			  u32 val);
+	void (*reset)(struct mhi_controller *mhi_cntrl);
 
 	size_t buffer_len;
 	int index;
@@ -681,6 +683,13 @@ enum mhi_ee_type mhi_get_exec_env(struct mhi_controller *mhi_cntrl);
 enum mhi_state mhi_get_mhi_state(struct mhi_controller *mhi_cntrl);
 
 /**
+ * mhi_soc_reset - Trigger a device reset. This can be used as a last resort
+ *		   to reset and recover a device.
+ * @mhi_cntrl: MHI controller
+ */
+void mhi_soc_reset(struct mhi_controller *mhi_cntrl);
+
+/**
  * mhi_device_get - Disable device low power mode
  * @mhi_dev: Device associated with the channel
  */
-- 
2.7.4

Re: [PATCH v7 01/10] bus: mhi: core: Add device hardware reset support

[Manivannan Sadhasivam]

On Mon, Jan 04, 2021 at 02:49:30PM +0100, Loic Poulain wrote:
> The MHI specification allows to perform a hard reset of the device
> when writing to the SOC_RESET register. It can be used to completely
> restart the device (e.g. in case of unrecoverable MHI error).
> 
> This is up to the MHI controller driver to determine when this hard
> reset should be used, and in case of MHI errors, should be used as
> a reset of last resort (after standard MHI stack reset).
> 
> This function is a stateless function, the MHI layer do nothing except
> triggering the reset by writing into the right register(s), this is up
> to the caller to ensure right mhi_controller state (e.g. unregister the
> controller if necessary).
> 
> Signed-off-by: Loic Poulain <loic.poulain@linaro.org>

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

Thanks,
Mani

> ---
>  drivers/bus/mhi/core/main.c | 13 +++++++++++++
>  include/linux/mhi.h         |  9 +++++++++
>  2 files changed, 22 insertions(+)
> 
> diff --git a/drivers/bus/mhi/core/main.c b/drivers/bus/mhi/core/main.c
> index a353d1e..c181a85 100644
> --- a/drivers/bus/mhi/core/main.c
> +++ b/drivers/bus/mhi/core/main.c
> @@ -142,6 +142,19 @@ enum mhi_state mhi_get_mhi_state(struct mhi_controller *mhi_cntrl)
>  }
>  EXPORT_SYMBOL_GPL(mhi_get_mhi_state);
>  
> +void mhi_soc_reset(struct mhi_controller *mhi_cntrl)
> +{
> +	if (mhi_cntrl->reset) {
> +		mhi_cntrl->reset(mhi_cntrl);
> +		return;
> +	}
> +
> +	/* Generic MHI SoC reset */
> +	mhi_write_reg(mhi_cntrl, mhi_cntrl->regs, MHI_SOC_RESET_REQ_OFFSET,
> +		      MHI_SOC_RESET_REQ);
> +}
> +EXPORT_SYMBOL_GPL(mhi_soc_reset);
> +
>  int mhi_map_single_no_bb(struct mhi_controller *mhi_cntrl,
>  			 struct mhi_buf_info *buf_info)
>  {
> diff --git a/include/linux/mhi.h b/include/linux/mhi.h
> index 04cf7f3..7ddbcd7 100644
> --- a/include/linux/mhi.h
> +++ b/include/linux/mhi.h
> @@ -355,6 +355,7 @@ struct mhi_controller_config {
>   * @unmap_single: CB function to destroy TRE buffer
>   * @read_reg: Read a MHI register via the physical link (required)
>   * @write_reg: Write a MHI register via the physical link (required)
> + * @reset: Controller specific reset function (optional)
>   * @buffer_len: Bounce buffer length
>   * @index: Index of the MHI controller instance
>   * @bounce_buf: Use of bounce buffer
> @@ -445,6 +446,7 @@ struct mhi_controller {
>  			u32 *out);
>  	void (*write_reg)(struct mhi_controller *mhi_cntrl, void __iomem *addr,
>  			  u32 val);
> +	void (*reset)(struct mhi_controller *mhi_cntrl);
>  
>  	size_t buffer_len;
>  	int index;
> @@ -681,6 +683,13 @@ enum mhi_ee_type mhi_get_exec_env(struct mhi_controller *mhi_cntrl);
>  enum mhi_state mhi_get_mhi_state(struct mhi_controller *mhi_cntrl);
>  
>  /**
> + * mhi_soc_reset - Trigger a device reset. This can be used as a last resort
> + *		   to reset and recover a device.
> + * @mhi_cntrl: MHI controller
> + */
> +void mhi_soc_reset(struct mhi_controller *mhi_cntrl);
> +
> +/**
>   * mhi_device_get - Disable device low power mode
>   * @mhi_dev: Device associated with the channel
>   */
> -- 
> 2.7.4
> 

[PATCH v7 02/10] mhi: pci-generic: Increase number of hardware events

[Loic Poulain]

If the IPA (IP hardware accelerator) is starved of event ring elements,
the modem is crashing (SDX55). That can be prevented by setting a
larger number of events (i.e 2 x number of channel ring elements).

Tested with FN980m module.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 drivers/bus/mhi/pci_generic.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index e3df838..13a7e4f 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -91,7 +91,7 @@ struct mhi_pci_dev_info {
 
 #define MHI_EVENT_CONFIG_HW_DATA(ev_ring, ch_num) \
 	{					\
-		.num_elements = 128,		\
+		.num_elements = 256,		\
 		.irq_moderation_ms = 5,		\
 		.irq = (ev_ring) + 1,		\
 		.priority = 1,			\
-- 
2.7.4

[PATCH v7 03/10] mhi: pci_generic: Enable burst mode for hardware channels

[Loic Poulain]

Hardware channels have a feature called burst mode that allows to
queue transfer ring element(s) (TRE) to a channel without ringing
the device doorbell. In that mode, the device is polling the channel
context for new elements. This reduces the frequency of host initiated
doorbells and increase throughput.

Create a new dedicated macro for hardware channels with burst enabled.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 drivers/bus/mhi/pci_generic.c | 34 ++++++++++++++++++++++++++++++++--
 1 file changed, 32 insertions(+), 2 deletions(-)

diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index 13a7e4f..077595c 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -76,6 +76,36 @@ struct mhi_pci_dev_info {
 		.offload_channel = false,	\
 	}
 
+#define MHI_CHANNEL_CONFIG_HW_UL(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_TO_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_AMSS),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_ENABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = true,		\
+	}						\
+
+#define MHI_CHANNEL_CONFIG_HW_DL(ch_num, ch_name, el_count, ev_ring) \
+	{						\
+		.num = ch_num,				\
+		.name = ch_name,			\
+		.num_elements = el_count,		\
+		.event_ring = ev_ring,			\
+		.dir = DMA_FROM_DEVICE,			\
+		.ee_mask = BIT(MHI_EE_AMSS),		\
+		.pollcfg = 0,				\
+		.doorbell = MHI_DB_BRST_ENABLE,	\
+		.lpm_notify = false,			\
+		.offload_channel = false,		\
+		.doorbell_mode_switch = true,		\
+	}
+
 #define MHI_EVENT_CONFIG_DATA(ev_ring)		\
 	{					\
 		.num_elements = 128,		\
@@ -110,8 +140,8 @@ static const struct mhi_channel_config modem_qcom_v1_mhi_channels[] = {
 	MHI_CHANNEL_CONFIG_DL(15, "QMI", 4, 0),
 	MHI_CHANNEL_CONFIG_UL(20, "IPCR", 8, 0),
 	MHI_CHANNEL_CONFIG_DL(21, "IPCR", 8, 0),
-	MHI_CHANNEL_CONFIG_UL(100, "IP_HW0", 128, 1),
-	MHI_CHANNEL_CONFIG_DL(101, "IP_HW0", 128, 2),
+	MHI_CHANNEL_CONFIG_HW_UL(100, "IP_HW0", 128, 1),
+	MHI_CHANNEL_CONFIG_HW_DL(101, "IP_HW0", 128, 2),
 };
 
 static const struct mhi_event_config modem_qcom_v1_mhi_events[] = {
-- 
2.7.4

[PATCH v7 04/10] mhi: pci_generic: Add support for reset

[Loic Poulain]

Add support for resetting the device, reset can be triggered in case
of error or manually via sysfs (/sys/bus/pci/devices/*/reset).

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
---
 drivers/bus/mhi/pci_generic.c | 121 +++++++++++++++++++++++++++++++++++++-----
 1 file changed, 108 insertions(+), 13 deletions(-)

diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index 077595c..b2307e7 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -8,6 +8,7 @@
  * Copyright (C) 2020 Linaro Ltd <loic.poulain@linaro.org>
  */
 
+#include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/mhi.h>
 #include <linux/module.h>
@@ -15,6 +16,7 @@
 
 #define MHI_PCI_DEFAULT_BAR_NUM 0
 
+#define MHI_POST_RESET_DELAY_MS 500
 /**
  * struct mhi_pci_dev_info - MHI PCI device specific information
  * @config: MHI controller configuration
@@ -177,6 +179,16 @@ static const struct pci_device_id mhi_pci_id_table[] = {
 };
 MODULE_DEVICE_TABLE(pci, mhi_pci_id_table);
 
+enum mhi_pci_device_status {
+	MHI_PCI_DEV_STARTED,
+};
+
+struct mhi_pci_device {
+	struct mhi_controller mhi_cntrl;
+	struct pci_saved_state *pci_state;
+	unsigned long status;
+};
+
 static int mhi_pci_read_reg(struct mhi_controller *mhi_cntrl,
 			    void __iomem *addr, u32 *out)
 {
@@ -196,6 +208,20 @@ static void mhi_pci_status_cb(struct mhi_controller *mhi_cntrl,
 	/* Nothing to do for now */
 }
 
+static bool mhi_pci_is_alive(struct mhi_controller *mhi_cntrl)
+{
+	struct pci_dev *pdev = to_pci_dev(mhi_cntrl->cntrl_dev);
+	u16 vendor = 0;
+
+	if (pci_read_config_word(pdev, PCI_VENDOR_ID, &vendor))
+		return false;
+
+	if (vendor == (u16) ~0 || vendor == 0)
+		return false;
+
+	return true;
+}
+
 static int mhi_pci_claim(struct mhi_controller *mhi_cntrl,
 			 unsigned int bar_num, u64 dma_mask)
 {
@@ -291,16 +317,20 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	const struct mhi_pci_dev_info *info = (struct mhi_pci_dev_info *) id->driver_data;
 	const struct mhi_controller_config *mhi_cntrl_config;
+	struct mhi_pci_device *mhi_pdev;
 	struct mhi_controller *mhi_cntrl;
 	int err;
 
 	dev_dbg(&pdev->dev, "MHI PCI device found: %s\n", info->name);
 
-	mhi_cntrl = mhi_alloc_controller();
-	if (!mhi_cntrl)
+	/* mhi_pdev.mhi_cntrl must be zero-initialized */
+	mhi_pdev = devm_kzalloc(&pdev->dev, sizeof(*mhi_pdev), GFP_KERNEL);
+	if (!mhi_pdev)
 		return -ENOMEM;
 
 	mhi_cntrl_config = info->config;
+	mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
 	mhi_cntrl->cntrl_dev = &pdev->dev;
 	mhi_cntrl->iova_start = 0;
 	mhi_cntrl->iova_stop = DMA_BIT_MASK(info->dma_data_width);
@@ -315,17 +345,21 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 
 	err = mhi_pci_claim(mhi_cntrl, info->bar_num, DMA_BIT_MASK(info->dma_data_width));
 	if (err)
-		goto err_release;
+		return err;
 
 	err = mhi_pci_get_irqs(mhi_cntrl, mhi_cntrl_config);
 	if (err)
-		goto err_release;
+		return err;
+
+	pci_set_drvdata(pdev, mhi_pdev);
 
-	pci_set_drvdata(pdev, mhi_cntrl);
+	/* Have stored pci confspace at hand for restore in sudden PCI error */
+	pci_save_state(pdev);
+	mhi_pdev->pci_state = pci_store_saved_state(pdev);
 
 	err = mhi_register_controller(mhi_cntrl, mhi_cntrl_config);
 	if (err)
-		goto err_release;
+		return err;
 
 	/* MHI bus does not power up the controller by default */
 	err = mhi_prepare_for_power_up(mhi_cntrl);
@@ -340,33 +374,94 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		goto err_unprepare;
 	}
 
+	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
+
 	return 0;
 
 err_unprepare:
 	mhi_unprepare_after_power_down(mhi_cntrl);
 err_unregister:
 	mhi_unregister_controller(mhi_cntrl);
-err_release:
-	mhi_free_controller(mhi_cntrl);
 
 	return err;
 }
 
 static void mhi_pci_remove(struct pci_dev *pdev)
 {
-	struct mhi_controller *mhi_cntrl = pci_get_drvdata(pdev);
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, true);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	}
 
-	mhi_power_down(mhi_cntrl, true);
-	mhi_unprepare_after_power_down(mhi_cntrl);
 	mhi_unregister_controller(mhi_cntrl);
-	mhi_free_controller(mhi_cntrl);
 }
 
+static void mhi_pci_reset_prepare(struct pci_dev *pdev)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	dev_info(&pdev->dev, "reset\n");
+
+	/* Clean up MHI state */
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, false);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	}
+
+	/* cause internal device reset */
+	mhi_soc_reset(mhi_cntrl);
+
+	/* Be sure device reset has been executed */
+	msleep(MHI_POST_RESET_DELAY_MS);
+}
+
+static void mhi_pci_reset_done(struct pci_dev *pdev)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+	int err;
+
+	/* Restore initial known working PCI state */
+	pci_load_saved_state(pdev, mhi_pdev->pci_state);
+	pci_restore_state(pdev);
+
+	/* Is device status available ? */
+	if (!mhi_pci_is_alive(mhi_cntrl)) {
+		dev_err(&pdev->dev, "reset failed\n");
+		return;
+	}
+
+	err = mhi_prepare_for_power_up(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to prepare MHI controller\n");
+		return;
+	}
+
+	err = mhi_sync_power_up(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to power up MHI controller\n");
+		mhi_unprepare_after_power_down(mhi_cntrl);
+		return;
+	}
+
+	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
+}
+
+static const struct pci_error_handlers mhi_pci_err_handler = {
+	.reset_prepare = mhi_pci_reset_prepare,
+	.reset_done = mhi_pci_reset_done,
+};
+
 static struct pci_driver mhi_pci_driver = {
 	.name		= "mhi-pci-generic",
 	.id_table	= mhi_pci_id_table,
 	.probe		= mhi_pci_probe,
-	.remove		= mhi_pci_remove
+	.remove		= mhi_pci_remove,
+	.err_handler	= &mhi_pci_err_handler,
 };
 module_pci_driver(mhi_pci_driver);
 
-- 
2.7.4

Re: [PATCH v7 04/10] mhi: pci_generic: Add support for reset

[Manivannan Sadhasivam]

On Mon, Jan 04, 2021 at 02:49:33PM +0100, Loic Poulain wrote:
> Add support for resetting the device, reset can be triggered in case
> of error or manually via sysfs (/sys/bus/pci/devices/*/reset).
> 
> Signed-off-by: Loic Poulain <loic.poulain@linaro.org>

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

Thanks,
Mani

> ---
>  drivers/bus/mhi/pci_generic.c | 121 +++++++++++++++++++++++++++++++++++++-----
>  1 file changed, 108 insertions(+), 13 deletions(-)
> 
> diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
> index 077595c..b2307e7 100644
> --- a/drivers/bus/mhi/pci_generic.c
> +++ b/drivers/bus/mhi/pci_generic.c
> @@ -8,6 +8,7 @@
>   * Copyright (C) 2020 Linaro Ltd <loic.poulain@linaro.org>
>   */
>  
> +#include <linux/delay.h>
>  #include <linux/device.h>
>  #include <linux/mhi.h>
>  #include <linux/module.h>
> @@ -15,6 +16,7 @@
>  
>  #define MHI_PCI_DEFAULT_BAR_NUM 0
>  
> +#define MHI_POST_RESET_DELAY_MS 500
>  /**
>   * struct mhi_pci_dev_info - MHI PCI device specific information
>   * @config: MHI controller configuration
> @@ -177,6 +179,16 @@ static const struct pci_device_id mhi_pci_id_table[] = {
>  };
>  MODULE_DEVICE_TABLE(pci, mhi_pci_id_table);
>  
> +enum mhi_pci_device_status {
> +	MHI_PCI_DEV_STARTED,
> +};
> +
> +struct mhi_pci_device {
> +	struct mhi_controller mhi_cntrl;
> +	struct pci_saved_state *pci_state;
> +	unsigned long status;
> +};
> +
>  static int mhi_pci_read_reg(struct mhi_controller *mhi_cntrl,
>  			    void __iomem *addr, u32 *out)
>  {
> @@ -196,6 +208,20 @@ static void mhi_pci_status_cb(struct mhi_controller *mhi_cntrl,
>  	/* Nothing to do for now */
>  }
>  
> +static bool mhi_pci_is_alive(struct mhi_controller *mhi_cntrl)
> +{
> +	struct pci_dev *pdev = to_pci_dev(mhi_cntrl->cntrl_dev);
> +	u16 vendor = 0;
> +
> +	if (pci_read_config_word(pdev, PCI_VENDOR_ID, &vendor))
> +		return false;
> +
> +	if (vendor == (u16) ~0 || vendor == 0)
> +		return false;
> +
> +	return true;
> +}
> +
>  static int mhi_pci_claim(struct mhi_controller *mhi_cntrl,
>  			 unsigned int bar_num, u64 dma_mask)
>  {
> @@ -291,16 +317,20 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>  {
>  	const struct mhi_pci_dev_info *info = (struct mhi_pci_dev_info *) id->driver_data;
>  	const struct mhi_controller_config *mhi_cntrl_config;
> +	struct mhi_pci_device *mhi_pdev;
>  	struct mhi_controller *mhi_cntrl;
>  	int err;
>  
>  	dev_dbg(&pdev->dev, "MHI PCI device found: %s\n", info->name);
>  
> -	mhi_cntrl = mhi_alloc_controller();
> -	if (!mhi_cntrl)
> +	/* mhi_pdev.mhi_cntrl must be zero-initialized */
> +	mhi_pdev = devm_kzalloc(&pdev->dev, sizeof(*mhi_pdev), GFP_KERNEL);
> +	if (!mhi_pdev)
>  		return -ENOMEM;
>  
>  	mhi_cntrl_config = info->config;
> +	mhi_cntrl = &mhi_pdev->mhi_cntrl;
> +
>  	mhi_cntrl->cntrl_dev = &pdev->dev;
>  	mhi_cntrl->iova_start = 0;
>  	mhi_cntrl->iova_stop = DMA_BIT_MASK(info->dma_data_width);
> @@ -315,17 +345,21 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>  
>  	err = mhi_pci_claim(mhi_cntrl, info->bar_num, DMA_BIT_MASK(info->dma_data_width));
>  	if (err)
> -		goto err_release;
> +		return err;
>  
>  	err = mhi_pci_get_irqs(mhi_cntrl, mhi_cntrl_config);
>  	if (err)
> -		goto err_release;
> +		return err;
> +
> +	pci_set_drvdata(pdev, mhi_pdev);
>  
> -	pci_set_drvdata(pdev, mhi_cntrl);
> +	/* Have stored pci confspace at hand for restore in sudden PCI error */
> +	pci_save_state(pdev);
> +	mhi_pdev->pci_state = pci_store_saved_state(pdev);
>  
>  	err = mhi_register_controller(mhi_cntrl, mhi_cntrl_config);
>  	if (err)
> -		goto err_release;
> +		return err;
>  
>  	/* MHI bus does not power up the controller by default */
>  	err = mhi_prepare_for_power_up(mhi_cntrl);
> @@ -340,33 +374,94 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>  		goto err_unprepare;
>  	}
>  
> +	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
> +
>  	return 0;
>  
>  err_unprepare:
>  	mhi_unprepare_after_power_down(mhi_cntrl);
>  err_unregister:
>  	mhi_unregister_controller(mhi_cntrl);
> -err_release:
> -	mhi_free_controller(mhi_cntrl);
>  
>  	return err;
>  }
>  
>  static void mhi_pci_remove(struct pci_dev *pdev)
>  {
> -	struct mhi_controller *mhi_cntrl = pci_get_drvdata(pdev);
> +	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
> +	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
> +
> +	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
> +		mhi_power_down(mhi_cntrl, true);
> +		mhi_unprepare_after_power_down(mhi_cntrl);
> +	}
>  
> -	mhi_power_down(mhi_cntrl, true);
> -	mhi_unprepare_after_power_down(mhi_cntrl);
>  	mhi_unregister_controller(mhi_cntrl);
> -	mhi_free_controller(mhi_cntrl);
>  }
>  
> +static void mhi_pci_reset_prepare(struct pci_dev *pdev)
> +{
> +	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
> +	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
> +
> +	dev_info(&pdev->dev, "reset\n");
> +
> +	/* Clean up MHI state */
> +	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
> +		mhi_power_down(mhi_cntrl, false);
> +		mhi_unprepare_after_power_down(mhi_cntrl);
> +	}
> +
> +	/* cause internal device reset */
> +	mhi_soc_reset(mhi_cntrl);
> +
> +	/* Be sure device reset has been executed */
> +	msleep(MHI_POST_RESET_DELAY_MS);
> +}
> +
> +static void mhi_pci_reset_done(struct pci_dev *pdev)
> +{
> +	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
> +	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
> +	int err;
> +
> +	/* Restore initial known working PCI state */
> +	pci_load_saved_state(pdev, mhi_pdev->pci_state);
> +	pci_restore_state(pdev);
> +
> +	/* Is device status available ? */
> +	if (!mhi_pci_is_alive(mhi_cntrl)) {
> +		dev_err(&pdev->dev, "reset failed\n");
> +		return;
> +	}
> +
> +	err = mhi_prepare_for_power_up(mhi_cntrl);
> +	if (err) {
> +		dev_err(&pdev->dev, "failed to prepare MHI controller\n");
> +		return;
> +	}
> +
> +	err = mhi_sync_power_up(mhi_cntrl);
> +	if (err) {
> +		dev_err(&pdev->dev, "failed to power up MHI controller\n");
> +		mhi_unprepare_after_power_down(mhi_cntrl);
> +		return;
> +	}
> +
> +	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
> +}
> +
> +static const struct pci_error_handlers mhi_pci_err_handler = {
> +	.reset_prepare = mhi_pci_reset_prepare,
> +	.reset_done = mhi_pci_reset_done,
> +};
> +
>  static struct pci_driver mhi_pci_driver = {
>  	.name		= "mhi-pci-generic",
>  	.id_table	= mhi_pci_id_table,
>  	.probe		= mhi_pci_probe,
> -	.remove		= mhi_pci_remove
> +	.remove		= mhi_pci_remove,
> +	.err_handler	= &mhi_pci_err_handler,
>  };
>  module_pci_driver(mhi_pci_driver);
>  
> -- 
> 2.7.4
> 

[PATCH v7 05/10] mhi: pci_generic: Add suspend/resume/recovery procedure

[Loic Poulain]

Add support for system wide suspend/resume. During suspend, MHI
device controller must be put in M3 state and PCI bus in D3 state.

Add a recovery procedure allowing to reinitialize the device in case
of error during resume steps, which can happen if device loses power
(and so its context) while system suspend.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 drivers/bus/mhi/pci_generic.c | 105 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 105 insertions(+)

diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index b2307e7..3d459f3 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -13,6 +13,7 @@
 #include <linux/mhi.h>
 #include <linux/module.h>
 #include <linux/pci.h>
+#include <linux/workqueue.h>
 
 #define MHI_PCI_DEFAULT_BAR_NUM 0
 
@@ -186,6 +187,7 @@ enum mhi_pci_device_status {
 struct mhi_pci_device {
 	struct mhi_controller mhi_cntrl;
 	struct pci_saved_state *pci_state;
+	struct work_struct recovery_work;
 	unsigned long status;
 };
 
@@ -313,6 +315,50 @@ static void mhi_pci_runtime_put(struct mhi_controller *mhi_cntrl)
 	/* no PM for now */
 }
 
+static void mhi_pci_recovery_work(struct work_struct *work)
+{
+	struct mhi_pci_device *mhi_pdev = container_of(work, struct mhi_pci_device,
+						       recovery_work);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+	struct pci_dev *pdev = to_pci_dev(mhi_cntrl->cntrl_dev);
+	int err;
+
+	dev_warn(&pdev->dev, "device recovery started\n");
+
+	/* Clean up MHI state */
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, false);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	}
+
+	/* Check if we can recover without full reset */
+	pci_set_power_state(pdev, PCI_D0);
+	pci_load_saved_state(pdev, mhi_pdev->pci_state);
+	pci_restore_state(pdev);
+
+	if (!mhi_pci_is_alive(mhi_cntrl))
+		goto err_try_reset;
+
+	err = mhi_prepare_for_power_up(mhi_cntrl);
+	if (err)
+		goto err_try_reset;
+
+	err = mhi_sync_power_up(mhi_cntrl);
+	if (err)
+		goto err_unprepare;
+
+	dev_dbg(&pdev->dev, "Recovery completed\n");
+
+	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
+	return;
+
+err_unprepare:
+	mhi_unprepare_after_power_down(mhi_cntrl);
+err_try_reset:
+	if (pci_reset_function(pdev))
+		dev_err(&pdev->dev, "Recovery failed\n");
+}
+
 static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	const struct mhi_pci_dev_info *info = (struct mhi_pci_dev_info *) id->driver_data;
@@ -328,6 +374,8 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	if (!mhi_pdev)
 		return -ENOMEM;
 
+	INIT_WORK(&mhi_pdev->recovery_work, mhi_pci_recovery_work);
+
 	mhi_cntrl_config = info->config;
 	mhi_cntrl = &mhi_pdev->mhi_cntrl;
 
@@ -391,6 +439,8 @@ static void mhi_pci_remove(struct pci_dev *pdev)
 	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
 	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
 
+	cancel_work_sync(&mhi_pdev->recovery_work);
+
 	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
 		mhi_power_down(mhi_cntrl, true);
 		mhi_unprepare_after_power_down(mhi_cntrl);
@@ -456,12 +506,67 @@ static const struct pci_error_handlers mhi_pci_err_handler = {
 	.reset_done = mhi_pci_reset_done,
 };
 
+static int  __maybe_unused mhi_pci_suspend(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct mhi_pci_device *mhi_pdev = dev_get_drvdata(dev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	cancel_work_sync(&mhi_pdev->recovery_work);
+
+	/* Transition to M3 state */
+	mhi_pm_suspend(mhi_cntrl);
+
+	pci_save_state(pdev);
+	pci_disable_device(pdev);
+	pci_wake_from_d3(pdev, true);
+	pci_set_power_state(pdev, PCI_D3hot);
+
+	return 0;
+}
+
+static int __maybe_unused mhi_pci_resume(struct device *dev)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct mhi_pci_device *mhi_pdev = dev_get_drvdata(dev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+	int err;
+
+	pci_set_power_state(pdev, PCI_D0);
+	pci_restore_state(pdev);
+	pci_set_master(pdev);
+
+	err = pci_enable_device(pdev);
+	if (err)
+		goto err_recovery;
+
+	/* Exit M3, transition to M0 state */
+	err = mhi_pm_resume(mhi_cntrl);
+	if (err) {
+		dev_err(&pdev->dev, "failed to resume device: %d\n", err);
+		goto err_recovery;
+	}
+
+	return 0;
+
+err_recovery:
+	/* The device may have loose power or crashed, try recovering it */
+	queue_work(system_long_wq, &mhi_pdev->recovery_work);
+
+	return err;
+}
+
+static const struct dev_pm_ops mhi_pci_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(mhi_pci_suspend, mhi_pci_resume)
+};
+
 static struct pci_driver mhi_pci_driver = {
 	.name		= "mhi-pci-generic",
 	.id_table	= mhi_pci_id_table,
 	.probe		= mhi_pci_probe,
 	.remove		= mhi_pci_remove,
 	.err_handler	= &mhi_pci_err_handler,
+	.driver.pm	= &mhi_pci_pm_ops
 };
 module_pci_driver(mhi_pci_driver);
 
-- 
2.7.4

[PATCH v7 06/10] mhi: pci_generic: Add PCI error handlers

[Loic Poulain]

In AER capable root complex, errors are reported to the host which
can then act accordingly and perform PCI recovering procedure.

This patch enables error reporting and implements error_detected,
slot_reset and resume callbacks.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
---
 drivers/bus/mhi/pci_generic.c | 50 +++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index 3d459f3..0c12027 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -8,6 +8,7 @@
  * Copyright (C) 2020 Linaro Ltd <loic.poulain@linaro.org>
  */
 
+#include <linux/aer.h>
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/mhi.h>
@@ -405,6 +406,8 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	pci_save_state(pdev);
 	mhi_pdev->pci_state = pci_store_saved_state(pdev);
 
+	pci_enable_pcie_error_reporting(pdev);
+
 	err = mhi_register_controller(mhi_cntrl, mhi_cntrl_config);
 	if (err)
 		return err;
@@ -501,7 +504,54 @@ static void mhi_pci_reset_done(struct pci_dev *pdev)
 	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
 }
 
+static pci_ers_result_t mhi_pci_error_detected(struct pci_dev *pdev,
+					       pci_channel_state_t state)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	dev_err(&pdev->dev, "PCI error detected, state = %u\n", state);
+
+	if (state == pci_channel_io_perm_failure)
+		return PCI_ERS_RESULT_DISCONNECT;
+
+	/* Clean up MHI state */
+	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
+		mhi_power_down(mhi_cntrl, false);
+		mhi_unprepare_after_power_down(mhi_cntrl);
+	} else {
+		/* Nothing to do */
+		return PCI_ERS_RESULT_RECOVERED;
+	}
+
+	pci_disable_device(pdev);
+
+	return PCI_ERS_RESULT_NEED_RESET;
+}
+
+static pci_ers_result_t mhi_pci_slot_reset(struct pci_dev *pdev)
+{
+	if (pci_enable_device(pdev)) {
+		dev_err(&pdev->dev, "Cannot re-enable PCI device after reset.\n");
+		return PCI_ERS_RESULT_DISCONNECT;
+	}
+
+	return PCI_ERS_RESULT_RECOVERED;
+}
+
+static void mhi_pci_io_resume(struct pci_dev *pdev)
+{
+	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
+
+	dev_err(&pdev->dev, "PCI slot reset done\n");
+
+	queue_work(system_long_wq, &mhi_pdev->recovery_work);
+}
+
 static const struct pci_error_handlers mhi_pci_err_handler = {
+	.error_detected = mhi_pci_error_detected,
+	.slot_reset = mhi_pci_slot_reset,
+	.resume = mhi_pci_io_resume,
 	.reset_prepare = mhi_pci_reset_prepare,
 	.reset_done = mhi_pci_reset_done,
 };
-- 
2.7.4

Re: [PATCH v7 06/10] mhi: pci_generic: Add PCI error handlers

[Manivannan Sadhasivam]

On Mon, Jan 04, 2021 at 02:49:35PM +0100, Loic Poulain wrote:
> In AER capable root complex, errors are reported to the host which
> can then act accordingly and perform PCI recovering procedure.
> 
> This patch enables error reporting and implements error_detected,
> slot_reset and resume callbacks.
> 
> Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
> Reviewed-by Hemant Kumar <hemantk@codeaurora.org>

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

Thanks,
Mani

> ---
>  drivers/bus/mhi/pci_generic.c | 50 +++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 50 insertions(+)
> 
> diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
> index 3d459f3..0c12027 100644
> --- a/drivers/bus/mhi/pci_generic.c
> +++ b/drivers/bus/mhi/pci_generic.c
> @@ -8,6 +8,7 @@
>   * Copyright (C) 2020 Linaro Ltd <loic.poulain@linaro.org>
>   */
>  
> +#include <linux/aer.h>
>  #include <linux/delay.h>
>  #include <linux/device.h>
>  #include <linux/mhi.h>
> @@ -405,6 +406,8 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>  	pci_save_state(pdev);
>  	mhi_pdev->pci_state = pci_store_saved_state(pdev);
>  
> +	pci_enable_pcie_error_reporting(pdev);
> +
>  	err = mhi_register_controller(mhi_cntrl, mhi_cntrl_config);
>  	if (err)
>  		return err;
> @@ -501,7 +504,54 @@ static void mhi_pci_reset_done(struct pci_dev *pdev)
>  	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
>  }
>  
> +static pci_ers_result_t mhi_pci_error_detected(struct pci_dev *pdev,
> +					       pci_channel_state_t state)
> +{
> +	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
> +	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
> +
> +	dev_err(&pdev->dev, "PCI error detected, state = %u\n", state);
> +
> +	if (state == pci_channel_io_perm_failure)
> +		return PCI_ERS_RESULT_DISCONNECT;
> +
> +	/* Clean up MHI state */
> +	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
> +		mhi_power_down(mhi_cntrl, false);
> +		mhi_unprepare_after_power_down(mhi_cntrl);
> +	} else {
> +		/* Nothing to do */
> +		return PCI_ERS_RESULT_RECOVERED;
> +	}
> +
> +	pci_disable_device(pdev);
> +
> +	return PCI_ERS_RESULT_NEED_RESET;
> +}
> +
> +static pci_ers_result_t mhi_pci_slot_reset(struct pci_dev *pdev)
> +{
> +	if (pci_enable_device(pdev)) {
> +		dev_err(&pdev->dev, "Cannot re-enable PCI device after reset.\n");
> +		return PCI_ERS_RESULT_DISCONNECT;
> +	}
> +
> +	return PCI_ERS_RESULT_RECOVERED;
> +}
> +
> +static void mhi_pci_io_resume(struct pci_dev *pdev)
> +{
> +	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
> +
> +	dev_err(&pdev->dev, "PCI slot reset done\n");
> +
> +	queue_work(system_long_wq, &mhi_pdev->recovery_work);
> +}
> +
>  static const struct pci_error_handlers mhi_pci_err_handler = {
> +	.error_detected = mhi_pci_error_detected,
> +	.slot_reset = mhi_pci_slot_reset,
> +	.resume = mhi_pci_io_resume,
>  	.reset_prepare = mhi_pci_reset_prepare,
>  	.reset_done = mhi_pci_reset_done,
>  };
> -- 
> 2.7.4
> 

[PATCH v7 07/10] mhi: pci_generic: Add health-check

[Loic Poulain]

If the modem crashes for any reason, we may not be able to detect
it at MHI level (MHI registers not reachable anymore).

This patch implements a health-check mechanism to check regularly
that device is alive (MHI layer can communicate with). If device
is not alive (because a crash or unexpected reset), the recovery
procedure is triggered.

Tested successfully with Telit FN980m module.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
---
 drivers/bus/mhi/pci_generic.c | 35 +++++++++++++++++++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index 0c12027..7e54d88 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -14,11 +14,15 @@
 #include <linux/mhi.h>
 #include <linux/module.h>
 #include <linux/pci.h>
+#include <linux/timer.h>
 #include <linux/workqueue.h>
 
 #define MHI_PCI_DEFAULT_BAR_NUM 0
 
 #define MHI_POST_RESET_DELAY_MS 500
+
+#define HEALTH_CHECK_PERIOD (HZ * 2)
+
 /**
  * struct mhi_pci_dev_info - MHI PCI device specific information
  * @config: MHI controller configuration
@@ -189,6 +193,7 @@ struct mhi_pci_device {
 	struct mhi_controller mhi_cntrl;
 	struct pci_saved_state *pci_state;
 	struct work_struct recovery_work;
+	struct timer_list health_check_timer;
 	unsigned long status;
 };
 
@@ -326,6 +331,8 @@ static void mhi_pci_recovery_work(struct work_struct *work)
 
 	dev_warn(&pdev->dev, "device recovery started\n");
 
+	del_timer(&mhi_pdev->health_check_timer);
+
 	/* Clean up MHI state */
 	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
 		mhi_power_down(mhi_cntrl, false);
@@ -351,6 +358,7 @@ static void mhi_pci_recovery_work(struct work_struct *work)
 	dev_dbg(&pdev->dev, "Recovery completed\n");
 
 	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
+	mod_timer(&mhi_pdev->health_check_timer, jiffies + HEALTH_CHECK_PERIOD);
 	return;
 
 err_unprepare:
@@ -360,6 +368,21 @@ static void mhi_pci_recovery_work(struct work_struct *work)
 		dev_err(&pdev->dev, "Recovery failed\n");
 }
 
+static void health_check(struct timer_list *t)
+{
+	struct mhi_pci_device *mhi_pdev = from_timer(mhi_pdev, t, health_check_timer);
+	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
+
+	if (!mhi_pci_is_alive(mhi_cntrl)) {
+		dev_err(mhi_cntrl->cntrl_dev, "Device died\n");
+		queue_work(system_long_wq, &mhi_pdev->recovery_work);
+		return;
+	}
+
+	/* reschedule in two seconds */
+	mod_timer(&mhi_pdev->health_check_timer, jiffies + HEALTH_CHECK_PERIOD);
+}
+
 static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	const struct mhi_pci_dev_info *info = (struct mhi_pci_dev_info *) id->driver_data;
@@ -376,6 +399,7 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		return -ENOMEM;
 
 	INIT_WORK(&mhi_pdev->recovery_work, mhi_pci_recovery_work);
+	timer_setup(&mhi_pdev->health_check_timer, health_check, 0);
 
 	mhi_cntrl_config = info->config;
 	mhi_cntrl = &mhi_pdev->mhi_cntrl;
@@ -427,6 +451,9 @@ static int mhi_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 
 	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
 
+	/* start health check */
+	mod_timer(&mhi_pdev->health_check_timer, jiffies + HEALTH_CHECK_PERIOD);
+
 	return 0;
 
 err_unprepare:
@@ -442,6 +469,7 @@ static void mhi_pci_remove(struct pci_dev *pdev)
 	struct mhi_pci_device *mhi_pdev = pci_get_drvdata(pdev);
 	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
 
+	del_timer(&mhi_pdev->health_check_timer);
 	cancel_work_sync(&mhi_pdev->recovery_work);
 
 	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
@@ -459,6 +487,8 @@ static void mhi_pci_reset_prepare(struct pci_dev *pdev)
 
 	dev_info(&pdev->dev, "reset\n");
 
+	del_timer(&mhi_pdev->health_check_timer);
+
 	/* Clean up MHI state */
 	if (test_and_clear_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status)) {
 		mhi_power_down(mhi_cntrl, false);
@@ -502,6 +532,7 @@ static void mhi_pci_reset_done(struct pci_dev *pdev)
 	}
 
 	set_bit(MHI_PCI_DEV_STARTED, &mhi_pdev->status);
+	mod_timer(&mhi_pdev->health_check_timer, jiffies + HEALTH_CHECK_PERIOD);
 }
 
 static pci_ers_result_t mhi_pci_error_detected(struct pci_dev *pdev,
@@ -562,6 +593,7 @@ static int  __maybe_unused mhi_pci_suspend(struct device *dev)
 	struct mhi_pci_device *mhi_pdev = dev_get_drvdata(dev);
 	struct mhi_controller *mhi_cntrl = &mhi_pdev->mhi_cntrl;
 
+	del_timer(&mhi_pdev->health_check_timer);
 	cancel_work_sync(&mhi_pdev->recovery_work);
 
 	/* Transition to M3 state */
@@ -597,6 +629,9 @@ static int __maybe_unused mhi_pci_resume(struct device *dev)
 		goto err_recovery;
 	}
 
+	/* Resume health check */
+	mod_timer(&mhi_pdev->health_check_timer, jiffies + HEALTH_CHECK_PERIOD);
+
 	return 0;
 
 err_recovery:
-- 
2.7.4

[PATCH v7 08/10] mhi: pci_generic: Increase controller timeout value

[Loic Poulain]

On cold boot, device can take slightly more than 5 seconds to start.
Increase the timeout to prevent MHI power-up issues.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 drivers/bus/mhi/pci_generic.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index 7e54d88..5188ca2 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -162,7 +162,7 @@ static const struct mhi_event_config modem_qcom_v1_mhi_events[] = {
 
 static const struct mhi_controller_config modem_qcom_v1_mhiv_config = {
 	.max_channels = 128,
-	.timeout_ms = 5000,
+	.timeout_ms = 8000,
 	.num_channels = ARRAY_SIZE(modem_qcom_v1_mhi_channels),
 	.ch_cfg = modem_qcom_v1_mhi_channels,
 	.num_events = ARRAY_SIZE(modem_qcom_v1_mhi_events),
-- 
2.7.4

[PATCH v7 09/10] mhi: pci_generic: Add diag channels

[Loic Poulain]

Add support for Diag over MHI. Qualcomm Diag is the qualcomm
diagnostics interface that can be used to collect modem logs,
events, traces, etc. It can be used by tools such QPST or QXDM.

This patch adds the DIAG channels and a dedicated event ring.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 drivers/bus/mhi/pci_generic.c | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index 5188ca2..a4b6221 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -142,22 +142,26 @@ struct mhi_pci_dev_info {
 	}
 
 static const struct mhi_channel_config modem_qcom_v1_mhi_channels[] = {
+	MHI_CHANNEL_CONFIG_UL(4, "DIAG", 16, 1),
+	MHI_CHANNEL_CONFIG_DL(5, "DIAG", 16, 1),
 	MHI_CHANNEL_CONFIG_UL(12, "MBIM", 4, 0),
 	MHI_CHANNEL_CONFIG_DL(13, "MBIM", 4, 0),
 	MHI_CHANNEL_CONFIG_UL(14, "QMI", 4, 0),
 	MHI_CHANNEL_CONFIG_DL(15, "QMI", 4, 0),
 	MHI_CHANNEL_CONFIG_UL(20, "IPCR", 8, 0),
 	MHI_CHANNEL_CONFIG_DL(21, "IPCR", 8, 0),
-	MHI_CHANNEL_CONFIG_HW_UL(100, "IP_HW0", 128, 1),
-	MHI_CHANNEL_CONFIG_HW_DL(101, "IP_HW0", 128, 2),
+	MHI_CHANNEL_CONFIG_HW_UL(100, "IP_HW0", 128, 2),
+	MHI_CHANNEL_CONFIG_HW_DL(101, "IP_HW0", 128, 3),
 };
 
 static const struct mhi_event_config modem_qcom_v1_mhi_events[] = {
 	/* first ring is control+data ring */
 	MHI_EVENT_CONFIG_CTRL(0),
+	/* DIAG dedicated event ring */
+	MHI_EVENT_CONFIG_DATA(1),
 	/* Hardware channels request dedicated hardware event rings */
-	MHI_EVENT_CONFIG_HW_DATA(1, 100),
-	MHI_EVENT_CONFIG_HW_DATA(2, 101)
+	MHI_EVENT_CONFIG_HW_DATA(2, 100),
+	MHI_EVENT_CONFIG_HW_DATA(3, 101)
 };
 
 static const struct mhi_controller_config modem_qcom_v1_mhiv_config = {
-- 
2.7.4

[PATCH v7 10/10] mhi: pci_generic: Set irq moderation value to 1ms for hw channels

[Loic Poulain]

MHI hardware channels are usually the hardware accelerated data path
e.g. IP packets path for modems. This path needs to be optimized for
low latency and high throughput. After several tests on FN980m SDX55
based modem, it seems 1ms is a good default irq_moderation value:

- It allows to reach the maximum download throughput
- It introduces limited latency (5ms is too high)
- It prevents interrupt flooding

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
---
 drivers/bus/mhi/pci_generic.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
index a4b6221..1603c83 100644
--- a/drivers/bus/mhi/pci_generic.c
+++ b/drivers/bus/mhi/pci_generic.c
@@ -130,7 +130,7 @@ struct mhi_pci_dev_info {
 #define MHI_EVENT_CONFIG_HW_DATA(ev_ring, ch_num) \
 	{					\
 		.num_elements = 256,		\
-		.irq_moderation_ms = 5,		\
+		.irq_moderation_ms = 1,		\
 		.irq = (ev_ring) + 1,		\
 		.priority = 1,			\
 		.mode = MHI_DB_BRST_DISABLE,	\
-- 
2.7.4

Re: [PATCH v7 10/10] mhi: pci_generic: Set irq moderation value to 1ms for hw channels

[Manivannan Sadhasivam]

On Mon, Jan 04, 2021 at 02:49:39PM +0100, Loic Poulain wrote:
> MHI hardware channels are usually the hardware accelerated data path
> e.g. IP packets path for modems. This path needs to be optimized for
> low latency and high throughput. After several tests on FN980m SDX55
> based modem, it seems 1ms is a good default irq_moderation value:
> 
> - It allows to reach the maximum download throughput
> - It introduces limited latency (5ms is too high)
> - It prevents interrupt flooding
> 
> Signed-off-by: Loic Poulain <loic.poulain@linaro.org>

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

Thanks,
Mani

> ---
>  drivers/bus/mhi/pci_generic.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/drivers/bus/mhi/pci_generic.c b/drivers/bus/mhi/pci_generic.c
> index a4b6221..1603c83 100644
> --- a/drivers/bus/mhi/pci_generic.c
> +++ b/drivers/bus/mhi/pci_generic.c
> @@ -130,7 +130,7 @@ struct mhi_pci_dev_info {
>  #define MHI_EVENT_CONFIG_HW_DATA(ev_ring, ch_num) \
>  	{					\
>  		.num_elements = 256,		\
> -		.irq_moderation_ms = 5,		\
> +		.irq_moderation_ms = 1,		\
>  		.irq = (ev_ring) + 1,		\
>  		.priority = 1,			\
>  		.mode = MHI_DB_BRST_DISABLE,	\
> -- 
> 2.7.4
>