[PATCH v4 0/5] Enable Bluetooth functionality for WCN6750

[PATCH v4 0/5] Enable Bluetooth functionality for WCN6750

[Venkata Lakshmi Narayana Gubba]

These patches enables Bluetooth functionalties for new Qualcomm
Bluetooth SoC wcn6750.

Venkata Lakshmi Narayana Gubba (5):
  Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750
  Bluetooth: btqca: Add support for firmware image with mbn type for
    WCN6750
  Bluetooth: btqca: Moved extracting rom version info to common place
  dt-bindings: net: bluetooth: Convert Qualcomm BT binding to DT schema
  dt-bindings: net: bluetooth: Add device tree bindings for QTI chip
    wcn6750

 .../devicetree/bindings/net/qualcomm-bluetooth.txt |  69 --------
 .../bindings/net/qualcomm-bluetooth.yaml           | 183 +++++++++++++++++++++
 drivers/bluetooth/btqca.c                          |  90 +++++++---
 drivers/bluetooth/btqca.h                          |  14 +-
 drivers/bluetooth/hci_qca.c                        | 114 ++++++++++---
 5 files changed, 354 insertions(+), 116 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
 create mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml

-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH v4 1/5] Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750

[Venkata Lakshmi Narayana Gubba]

Added regulators,GPIOs and changes required to power on/off wcn6750.
Added support for firmware download for wcn6750.

Changes done in detail:
1. Added regulators and corresponding current values.
2. Added sw_ctrl GPIO pin which is output from BT SoC and indicates
   status of clock supply to BT SoC.
3. Added inline function to check if the SoC type is wcn6750.
4. Modified the function qca_wcn3990_init() to support wcn6750 and
   renamed it to qca_regulator_init().

Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
---
 drivers/bluetooth/btqca.c   |  13 ++++-
 drivers/bluetooth/btqca.h   |  11 +++++
 drivers/bluetooth/hci_qca.c | 114 ++++++++++++++++++++++++++++++++++++--------
 3 files changed, 115 insertions(+), 23 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index bd71dfc..9574249 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -530,6 +530,11 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 			    (soc_ver & 0x0000000f);
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/htbtfw%02x.tlv", rom_ver);
+	} else if (soc_type == QCA_WCN6750) {
+		rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
+			    (soc_ver & 0x0000000f);
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/msbtfw%02x.tlv", rom_ver);
 	} else {
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/rampatch_%08x.bin", soc_ver);
@@ -561,6 +566,9 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	else if (soc_type == QCA_QCA6390)
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/htnv%02x.bin", rom_ver);
+	else if (soc_type == QCA_WCN6750)
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/msnv%02x.bin", rom_ver);
 	else
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/nvm_%08x.bin", soc_ver);
@@ -577,13 +585,14 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 			return err;
 	}
 
-	/* WCN399x supports the Microsoft vendor extension with 0xFD70 as the
+	/* WCN399x and WCN6750 supports the Microsoft vendor extension with 0xFD70 as the
 	 * VsMsftOpCode.
 	 */
 	switch (soc_type) {
 	case QCA_WCN3990:
 	case QCA_WCN3991:
 	case QCA_WCN3998:
+	case QCA_WCN6750:
 		hci_set_msft_opcode(hdev, 0xFD70);
 		break;
 	default:
@@ -597,7 +606,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 		return err;
 	}
 
-	if (soc_type == QCA_WCN3991) {
+	if (soc_type == QCA_WCN3991 || soc_type == QCA_WCN6750) {
 		/* get fw build info */
 		err = qca_read_fw_build_info(hdev);
 		if (err < 0)
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index b19add7..6ecd329 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -143,6 +143,7 @@ enum qca_btsoc_type {
 	QCA_WCN3998,
 	QCA_WCN3991,
 	QCA_QCA6390,
+	QCA_WCN6750,
 };
 
 #if IS_ENABLED(CONFIG_BT_QCA)
@@ -160,6 +161,11 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
 	return soc_type == QCA_WCN3990 || soc_type == QCA_WCN3991 ||
 	       soc_type == QCA_WCN3998;
 }
+static inline bool qca_is_wcn6750(enum qca_btsoc_type soc_type)
+{
+	return soc_type == QCA_WCN6750;
+}
+
 #else
 
 static inline int qca_set_bdaddr_rome(struct hci_dev *hdev, const bdaddr_t *bdaddr)
@@ -192,6 +198,11 @@ static inline bool qca_is_wcn399x(enum qca_btsoc_type soc_type)
 	return false;
 }
 
+static inline bool qca_is_wcn6750(enum qca_btsoc_type soc_type)
+{
+	return false;
+}
+
 static inline int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
 {
 	return -EOPNOTSUPP;
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index dc6551d..53deea2 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -218,6 +218,7 @@ struct qca_power {
 struct qca_serdev {
 	struct hci_uart	 serdev_hu;
 	struct gpio_desc *bt_en;
+	struct gpio_desc *sw_ctrl;
 	struct clk	 *susclk;
 	enum qca_btsoc_type btsoc_type;
 	struct qca_power *bt_power;
@@ -604,7 +605,8 @@ static int qca_open(struct hci_uart *hu)
 	if (hu->serdev) {
 		qcadev = serdev_device_get_drvdata(hu->serdev);
 
-		if (qca_is_wcn399x(qcadev->btsoc_type))
+		if (qca_is_wcn399x(qcadev->btsoc_type) ||
+		    qca_is_wcn6750(qcadev->btsoc_type))
 			hu->init_speed = qcadev->init_speed;
 
 		if (qcadev->oper_speed)
@@ -1308,7 +1310,8 @@ static int qca_set_baudrate(struct hci_dev *hdev, uint8_t baudrate)
 		      msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS));
 
 	/* Give the controller time to process the request */
-	if (qca_is_wcn399x(qca_soc_type(hu)))
+	if (qca_is_wcn399x(qca_soc_type(hu)) ||
+	    qca_is_wcn6750(qca_soc_type(hu)))
 		usleep_range(1000, 10000);
 	else
 		msleep(300);
@@ -1384,7 +1387,8 @@ static unsigned int qca_get_speed(struct hci_uart *hu,
 
 static int qca_check_speeds(struct hci_uart *hu)
 {
-	if (qca_is_wcn399x(qca_soc_type(hu))) {
+	if (qca_is_wcn399x(qca_soc_type(hu)) ||
+	    qca_is_wcn6750(qca_soc_type(hu))) {
 		if (!qca_get_speed(hu, QCA_INIT_SPEED) &&
 		    !qca_get_speed(hu, QCA_OPER_SPEED))
 			return -EINVAL;
@@ -1417,7 +1421,8 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
 		/* Disable flow control for wcn3990 to deassert RTS while
 		 * changing the baudrate of chip and host.
 		 */
-		if (qca_is_wcn399x(soc_type))
+		if (qca_is_wcn399x(soc_type) ||
+		    qca_is_wcn6750(soc_type))
 			hci_uart_set_flow_control(hu, true);
 
 		if (soc_type == QCA_WCN3990) {
@@ -1434,7 +1439,8 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
 		host_set_baudrate(hu, speed);
 
 error:
-		if (qca_is_wcn399x(soc_type))
+		if (qca_is_wcn399x(soc_type) ||
+		    qca_is_wcn6750(soc_type))
 			hci_uart_set_flow_control(hu, false);
 
 		if (soc_type == QCA_WCN3990) {
@@ -1585,10 +1591,12 @@ static bool qca_prevent_wake(struct hci_dev *hdev)
 	return !wakeup;
 }
 
-static int qca_wcn3990_init(struct hci_uart *hu)
+static int qca_regulator_init(struct hci_uart *hu)
 {
+	enum qca_btsoc_type soc_type = qca_soc_type(hu);
 	struct qca_serdev *qcadev;
 	int ret;
+	bool sw_ctrl_state;
 
 	/* Check for vregs status, may be hci down has turned
 	 * off the voltage regulator.
@@ -1607,16 +1615,33 @@ static int qca_wcn3990_init(struct hci_uart *hu)
 		}
 	}
 
-	/* Forcefully enable wcn3990 to enter in to boot mode. */
-	host_set_baudrate(hu, 2400);
-	ret = qca_send_power_pulse(hu, false);
-	if (ret)
-		return ret;
+	if (qca_is_wcn399x(soc_type)) {
+		/* Forcefully enable wcn399x to enter in to boot mode. */
+		host_set_baudrate(hu, 2400);
+		ret = qca_send_power_pulse(hu, false);
+		if (ret)
+			return ret;
+	}
+
+	/* For wcn6750 need to enable gpio bt_en */
+	if (qcadev->bt_en) {
+		gpiod_set_value_cansleep(qcadev->bt_en, 0);
+		msleep(50);
+		gpiod_set_value_cansleep(qcadev->bt_en, 1);
+		msleep(50);
+		if (qcadev->sw_ctrl) {
+			sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
+			bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
+		}
+	}
 
 	qca_set_speed(hu, QCA_INIT_SPEED);
-	ret = qca_send_power_pulse(hu, true);
-	if (ret)
-		return ret;
+
+	if (qca_is_wcn399x(soc_type)) {
+		ret = qca_send_power_pulse(hu, true);
+		if (ret)
+			return ret;
+	}
 
 	/* Now the device is in ready state to communicate with host.
 	 * To sync host with device we need to reopen port.
@@ -1649,8 +1674,9 @@ static int qca_power_on(struct hci_dev *hdev)
 	if (!hu->serdev)
 		return 0;
 
-	if (qca_is_wcn399x(soc_type)) {
-		ret = qca_wcn3990_init(hu);
+	if (qca_is_wcn399x(soc_type) ||
+	    qca_is_wcn6750(soc_type)) {
+		ret = qca_regulator_init(hu);
 	} else {
 		qcadev = serdev_device_get_drvdata(hu->serdev);
 		if (qcadev->bt_en) {
@@ -1689,7 +1715,8 @@ static int qca_setup(struct hci_uart *hu)
 	set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
 
 	bt_dev_info(hdev, "setting up %s",
-		qca_is_wcn399x(soc_type) ? "wcn399x" : "ROME/QCA6390");
+		qca_is_wcn399x(soc_type) ? "wcn399x" :
+		(soc_type == QCA_WCN6750) ? "wcn6750" : "ROME/QCA6390");
 
 	qca->memdump_state = QCA_MEMDUMP_IDLE;
 
@@ -1700,7 +1727,8 @@ static int qca_setup(struct hci_uart *hu)
 
 	clear_bit(QCA_SSR_TRIGGERED, &qca->flags);
 
-	if (qca_is_wcn399x(soc_type)) {
+	if (qca_is_wcn399x(soc_type) ||
+	    qca_is_wcn6750(soc_type)) {
 		set_bit(HCI_QUIRK_USE_BDADDR_PROPERTY, &hdev->quirks);
 
 		ret = qca_read_soc_version(hdev, &ver, soc_type);
@@ -1720,7 +1748,8 @@ static int qca_setup(struct hci_uart *hu)
 		qca_baudrate = qca_get_baudrate_value(speed);
 	}
 
-	if (!qca_is_wcn399x(soc_type)) {
+	if (!(qca_is_wcn399x(soc_type) ||
+	     qca_is_wcn6750(soc_type))) {
 		/* Get QCA version information */
 		ret = qca_read_soc_version(hdev, &ver, soc_type);
 		if (ret)
@@ -1828,12 +1857,30 @@ static const struct qca_device_data qca_soc_data_qca6390 = {
 	.num_vregs = 0,
 };
 
+static const struct qca_device_data qca_soc_data_wcn6750 = {
+	.soc_type = QCA_WCN6750,
+	.vregs = (struct qca_vreg []) {
+		{ "vddio", 5000 },
+		{ "vddaon", 26000 },
+		{ "vddbtcxmx", 126000 },
+		{ "vddrfacmn", 12500 },
+		{ "vddrfa0p8", 102000 },
+		{ "vddrfa1p7", 302000 },
+		{ "vddrfa1p2", 257000 },
+		{ "vddrfa2p2", 1700000 },
+		{ "vddasd", 200 },
+	},
+	.num_vregs = 9,
+	.capabilities = QCA_CAP_WIDEBAND_SPEECH | QCA_CAP_VALID_LE_STATES,
+};
+
 static void qca_power_shutdown(struct hci_uart *hu)
 {
 	struct qca_serdev *qcadev;
 	struct qca_data *qca = hu->priv;
 	unsigned long flags;
 	enum qca_btsoc_type soc_type = qca_soc_type(hu);
+	bool sw_ctrl_state;
 
 	/* From this point we go into power off state. But serial port is
 	 * still open, stop queueing the IBS data and flush all the buffered
@@ -1856,6 +1903,14 @@ static void qca_power_shutdown(struct hci_uart *hu)
 		host_set_baudrate(hu, 2400);
 		qca_send_power_pulse(hu, false);
 		qca_regulator_disable(qcadev);
+	} else if (soc_type == QCA_WCN6750) {
+		gpiod_set_value_cansleep(qcadev->bt_en, 0);
+		msleep(100);
+		qca_regulator_disable(qcadev);
+		if (qcadev->sw_ctrl) {
+			sw_ctrl_state = gpiod_get_value_cansleep(qcadev->sw_ctrl);
+			bt_dev_dbg(hu->hdev, "SW_CTRL is %d", sw_ctrl_state);
+		}
 	} else if (qcadev->bt_en) {
 		gpiod_set_value_cansleep(qcadev->bt_en, 0);
 	}
@@ -1978,7 +2033,9 @@ static int qca_serdev_probe(struct serdev_device *serdev)
 	if (!qcadev->oper_speed)
 		BT_DBG("UART will pick default operating speed");
 
-	if (data && qca_is_wcn399x(data->soc_type)) {
+	if (data &&
+	    (qca_is_wcn399x(data->soc_type) ||
+	    qca_is_wcn6750(data->soc_type))) {
 		qcadev->btsoc_type = data->soc_type;
 		qcadev->bt_power = devm_kzalloc(&serdev->dev,
 						sizeof(struct qca_power),
@@ -1996,6 +2053,18 @@ static int qca_serdev_probe(struct serdev_device *serdev)
 
 		qcadev->bt_power->vregs_on = false;
 
+		qcadev->bt_en = devm_gpiod_get_optional(&serdev->dev, "enable",
+					       GPIOD_OUT_LOW);
+		if (!qcadev->bt_en && data->soc_type == QCA_WCN6750) {
+			dev_err(&serdev->dev, "failed to acquire BT_EN gpio\n");
+			power_ctrl_enabled = false;
+		}
+
+		qcadev->sw_ctrl = devm_gpiod_get_optional(&serdev->dev, "swctrl",
+					       GPIOD_IN);
+		if (!qcadev->sw_ctrl && data->soc_type == QCA_WCN6750)
+			dev_warn(&serdev->dev, "failed to acquire SW_CTRL gpio\n");
+
 		qcadev->susclk = devm_clk_get_optional(&serdev->dev, NULL);
 		if (IS_ERR(qcadev->susclk)) {
 			dev_err(&serdev->dev, "failed to acquire clk\n");
@@ -2068,7 +2137,9 @@ static void qca_serdev_remove(struct serdev_device *serdev)
 	struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
 	struct qca_power *power = qcadev->bt_power;
 
-	if (qca_is_wcn399x(qcadev->btsoc_type) && power->vregs_on)
+	if ((qca_is_wcn399x(qcadev->btsoc_type) ||
+	     qca_is_wcn6750(qcadev->btsoc_type)) &&
+	     power->vregs_on)
 		qca_power_shutdown(&qcadev->serdev_hu);
 	else if (qcadev->susclk)
 		clk_disable_unprepare(qcadev->susclk);
@@ -2244,6 +2315,7 @@ static const struct of_device_id qca_bluetooth_of_match[] = {
 	{ .compatible = "qcom,wcn3990-bt", .data = &qca_soc_data_wcn3990},
 	{ .compatible = "qcom,wcn3991-bt", .data = &qca_soc_data_wcn3991},
 	{ .compatible = "qcom,wcn3998-bt", .data = &qca_soc_data_wcn3998},
+	{ .compatible = "qcom,wcn6750-bt", .data = &qca_soc_data_wcn6750},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, qca_bluetooth_of_match);
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

RE: Enable Bluetooth functionality for WCN6750

[bluez.test.bot]

[-- Attachment #1: Type: text/plain, Size: 3871 bytes --]

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=484453

---Test result---

Test Summary:
CheckPatch                    FAIL      2.37 seconds
GitLint                       FAIL      0.52 seconds
BuildKernel                   PASS      509.63 seconds
TestRunner: Setup             PASS      333.89 seconds
TestRunner: l2cap-tester      PASS      2.56 seconds
TestRunner: bnep-tester       PASS      1.86 seconds
TestRunner: mgmt-tester       PASS      25.77 seconds
TestRunner: rfcomm-tester     PASS      2.06 seconds
TestRunner: sco-tester        PASS      1.97 seconds
TestRunner: smp-tester        PASS      2.07 seconds
TestRunner: userchan-tester   PASS      1.89 seconds

Details
##############################
Test: CheckPatch - FAIL - 2.37 seconds
Run checkpatch.pl script with rule in .checkpatch.conf
dt-bindings: net: bluetooth: Convert Qualcomm BT binding to DT schema
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#12: 
deleted file mode 100644

WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst

WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst

total: 0 errors, 3 warnings, 112 lines checked

NOTE: For some of the reported defects, checkpatch may be able to
      mechanically convert to the typical style using --fix or --fix-inplace.

"[PATCH] dt-bindings: net: bluetooth: Convert Qualcomm BT binding to" has style problems, please review.

NOTE: If any of the errors are false positives, please report
      them to the maintainer, see CHECKPATCH in MAINTAINERS.


##############################
Test: GitLint - FAIL - 0.52 seconds
Run gitlint with rule in .gitlint
Bluetooth: btqca: Add support for firmware image with mbn type for WCN6750
1: T1 Title exceeds max length (74>72): "Bluetooth: btqca: Add support for firmware image with mbn type for WCN6750"

dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750
1: T1 Title exceeds max length (74>72): "dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750"


##############################
Test: BuildKernel - PASS - 509.63 seconds
Build Kernel with minimal configuration supports Bluetooth


##############################
Test: TestRunner: Setup - PASS - 333.89 seconds
Setup environment for running Test Runner


##############################
Test: TestRunner: l2cap-tester - PASS - 2.56 seconds
Run test-runner with l2cap-tester
Total: 40, Passed: 40 (100.0%), Failed: 0, Not Run: 0

##############################
Test: TestRunner: bnep-tester - PASS - 1.86 seconds
Run test-runner with bnep-tester
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0

##############################
Test: TestRunner: mgmt-tester - PASS - 25.77 seconds
Run test-runner with mgmt-tester
Total: 416, Passed: 403 (96.9%), Failed: 0, Not Run: 13

##############################
Test: TestRunner: rfcomm-tester - PASS - 2.06 seconds
Run test-runner with rfcomm-tester
Total: 9, Passed: 9 (100.0%), Failed: 0, Not Run: 0

##############################
Test: TestRunner: sco-tester - PASS - 1.97 seconds
Run test-runner with sco-tester
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0

##############################
Test: TestRunner: smp-tester - PASS - 2.07 seconds
Run test-runner with smp-tester
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0

##############################
Test: TestRunner: userchan-tester - PASS - 1.89 seconds
Run test-runner with userchan-tester
Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0



---
Regards,
Linux Bluetooth


[-- Attachment #2: l2cap-tester.log --]
[-- Type: application/octet-stream, Size: 44230 bytes --]

[-- Attachment #3: bnep-tester.log --]
[-- Type: application/octet-stream, Size: 3557 bytes --]

[-- Attachment #4: mgmt-tester.log --]
[-- Type: application/octet-stream, Size: 546745 bytes --]

[-- Attachment #5: rfcomm-tester.log --]
[-- Type: application/octet-stream, Size: 11677 bytes --]

[-- Attachment #6: sco-tester.log --]
[-- Type: application/octet-stream, Size: 9912 bytes --]

[-- Attachment #7: smp-tester.log --]
[-- Type: application/octet-stream, Size: 11822 bytes --]

[-- Attachment #8: userchan-tester.log --]
[-- Type: application/octet-stream, Size: 5454 bytes --]

[PATCH v4 2/5] Bluetooth: btqca: Add support for firmware image with mbn type for WCN6750

[Venkata Lakshmi Narayana Gubba]

1. Added support to download firmware image with mbn type for wcn6750
   as it supports mbn type image.
2. If mbn type image is not present then check for tlv type image.
3. Added debug logs for mbn type image.

Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
---
 drivers/bluetooth/btqca.c | 69 +++++++++++++++++++++++++++++++++++------------
 drivers/bluetooth/btqca.h |  3 ++-
 2 files changed, 54 insertions(+), 18 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 9574249..3210283 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -182,7 +182,8 @@ int qca_send_pre_shutdown_cmd(struct hci_dev *hdev)
 }
 EXPORT_SYMBOL_GPL(qca_send_pre_shutdown_cmd);
 
-static void qca_tlv_check_data(struct qca_fw_config *config,
+static void qca_tlv_check_data(struct hci_dev *hdev,
+			       struct qca_fw_config *config,
 		u8 *fw_data, enum qca_btsoc_type soc_type)
 {
 	const u8 *data;
@@ -194,19 +195,21 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
 	struct tlv_type_nvm *tlv_nvm;
 	uint8_t nvm_baud_rate = config->user_baud_rate;
 
-	tlv = (struct tlv_type_hdr *)fw_data;
-
-	type_len = le32_to_cpu(tlv->type_len);
-	length = (type_len >> 8) & 0x00ffffff;
-
-	BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
-	BT_DBG("Length\t\t : %d bytes", length);
-
 	config->dnld_mode = QCA_SKIP_EVT_NONE;
 	config->dnld_type = QCA_SKIP_EVT_NONE;
 
 	switch (config->type) {
+	case ELF_TYPE_PATCH:
+		config->dnld_mode = QCA_SKIP_EVT_VSE_CC;
+		config->dnld_type = QCA_SKIP_EVT_VSE_CC;
+
+		bt_dev_dbg(hdev, "File Class        : 0x%x", fw_data[4]);
+		bt_dev_dbg(hdev, "Data Encoding     : 0x%x", fw_data[5]);
+		bt_dev_dbg(hdev, "File version      : 0x%x", fw_data[6]);
+		break;
 	case TLV_TYPE_PATCH:
+		tlv = (struct tlv_type_hdr *)fw_data;
+		type_len = le32_to_cpu(tlv->type_len);
 		tlv_patch = (struct tlv_type_patch *)tlv->data;
 
 		/* For Rome version 1.1 to 3.1, all segment commands
@@ -218,6 +221,7 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
 		config->dnld_mode = tlv_patch->download_mode;
 		config->dnld_type = config->dnld_mode;
 
+		BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
 		BT_DBG("Total Length           : %d bytes",
 		       le32_to_cpu(tlv_patch->total_size));
 		BT_DBG("Patch Data Length      : %d bytes",
@@ -243,6 +247,14 @@ static void qca_tlv_check_data(struct qca_fw_config *config,
 		break;
 
 	case TLV_TYPE_NVM:
+		tlv = (struct tlv_type_hdr *)fw_data;
+
+		type_len = le32_to_cpu(tlv->type_len);
+		length = (type_len >> 8) & 0x00ffffff;
+
+		BT_DBG("TLV Type\t\t : 0x%x", type_len & 0x000000ff);
+		BT_DBG("Length\t\t : %d bytes", length);
+
 		idx = 0;
 		data = tlv->data;
 		while (idx < length) {
@@ -387,7 +399,8 @@ static int qca_inject_cmd_complete_event(struct hci_dev *hdev)
 
 static int qca_download_firmware(struct hci_dev *hdev,
 				 struct qca_fw_config *config,
-				 enum qca_btsoc_type soc_type)
+				 enum qca_btsoc_type soc_type,
+				 u8 rom_ver)
 {
 	const struct firmware *fw;
 	u8 *data;
@@ -398,9 +411,27 @@ static int qca_download_firmware(struct hci_dev *hdev,
 
 	ret = request_firmware(&fw, config->fwname, &hdev->dev);
 	if (ret) {
-		bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
-			   config->fwname, ret);
-		return ret;
+		/* For WCN6750, if mbn file is not present then check for
+		 * tlv file.
+		 */
+		if (soc_type == QCA_WCN6750 && config->type == ELF_TYPE_PATCH) {
+			bt_dev_dbg(hdev, "QCA Failed to request file: %s (%d)",
+				   config->fwname, ret);
+			config->type = TLV_TYPE_PATCH;
+			snprintf(config->fwname, sizeof(config->fwname),
+				 "qca/msbtfw%02x.tlv", rom_ver);
+			bt_dev_info(hdev, "QCA Downloading %s", config->fwname);
+			ret = request_firmware(&fw, config->fwname, &hdev->dev);
+			if (ret) {
+				bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+					   config->fwname, ret);
+				return ret;
+			}
+		} else {
+			bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+				   config->fwname, ret);
+			return ret;
+		}
 	}
 
 	size = fw->size;
@@ -415,7 +446,7 @@ static int qca_download_firmware(struct hci_dev *hdev,
 	memcpy(data, fw->data, size);
 	release_firmware(fw);
 
-	qca_tlv_check_data(config, data, soc_type);
+	qca_tlv_check_data(hdev, config, data, soc_type);
 
 	segment = data;
 	remain = size;
@@ -533,14 +564,18 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	} else if (soc_type == QCA_WCN6750) {
 		rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
 			    (soc_ver & 0x0000000f);
+		/* Choose mbn file by default.If mbn file is not found
+		 * then choose tlv file
+		 */
+		config.type = ELF_TYPE_PATCH;
 		snprintf(config.fwname, sizeof(config.fwname),
-			 "qca/msbtfw%02x.tlv", rom_ver);
+			 "qca/msbtfw%02x.mbn", rom_ver);
 	} else {
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/rampatch_%08x.bin", soc_ver);
 	}
 
-	err = qca_download_firmware(hdev, &config, soc_type);
+	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
 	if (err < 0) {
 		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
 		return err;
@@ -573,7 +608,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/nvm_%08x.bin", soc_ver);
 
-	err = qca_download_firmware(hdev, &config, soc_type);
+	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
 	if (err < 0) {
 		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
 		return err;
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index 6ecd329..30afa77 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -80,7 +80,8 @@ enum qca_tlv_dnld_mode {
 
 enum qca_tlv_type {
 	TLV_TYPE_PATCH = 1,
-	TLV_TYPE_NVM
+	TLV_TYPE_NVM,
+	ELF_TYPE_PATCH,
 };
 
 struct qca_fw_config {
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH v4 3/5] Bluetooth: btqca: Moved extracting rom version info to common place

[Venkata Lakshmi Narayana Gubba]

Moved extracting rom version info to common place as this code is
common in all if else ladder in qca_uart_setup.

Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
---
 drivers/bluetooth/btqca.c | 14 +++++---------
 1 file changed, 5 insertions(+), 9 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 3210283..be04d74 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -546,24 +546,20 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 
 	config.user_baud_rate = baudrate;
 
+	/* Firmware files to download are based on ROM version.
+	 * ROM version is derived from last two bytes of soc_ver.
+	 */
+	rom_ver = ((soc_ver & 0x00000f00) >> 0x04) | (soc_ver & 0x0000000f);
+
 	/* Download rampatch file */
 	config.type = TLV_TYPE_PATCH;
 	if (qca_is_wcn399x(soc_type)) {
-		/* Firmware files to download are based on ROM version.
-		 * ROM version is derived from last two bytes of soc_ver.
-		 */
-		rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
-			    (soc_ver & 0x0000000f);
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/crbtfw%02x.tlv", rom_ver);
 	} else if (soc_type == QCA_QCA6390) {
-		rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
-			    (soc_ver & 0x0000000f);
 		snprintf(config.fwname, sizeof(config.fwname),
 			 "qca/htbtfw%02x.tlv", rom_ver);
 	} else if (soc_type == QCA_WCN6750) {
-		rom_ver = ((soc_ver & 0x00000f00) >> 0x04) |
-			    (soc_ver & 0x0000000f);
 		/* Choose mbn file by default.If mbn file is not found
 		 * then choose tlv file
 		 */
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH v4 4/5] dt-bindings: net: bluetooth: Convert Qualcomm BT binding to DT schema

[Venkata Lakshmi Narayana Gubba]

Converted Qualcomm Bluetooth binidings to DT schema.

Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
---
 .../devicetree/bindings/net/qualcomm-bluetooth.txt |  69 -------------
 .../bindings/net/qualcomm-bluetooth.yaml           | 112 +++++++++++++++++++++
 2 files changed, 112 insertions(+), 69 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
 create mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml

diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
deleted file mode 100644
index 709ca6d..0000000
--- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
+++ /dev/null
@@ -1,69 +0,0 @@
-Qualcomm Bluetooth Chips
----------------------
-
-This documents the binding structure and common properties for serial
-attached Qualcomm devices.
-
-Serial attached Qualcomm devices shall be a child node of the host UART
-device the slave device is attached to.
-
-Required properties:
- - compatible: should contain one of the following:
-   * "qcom,qca6174-bt"
-   * "qcom,qca9377-bt"
-   * "qcom,wcn3990-bt"
-   * "qcom,wcn3991-bt"
-   * "qcom,wcn3998-bt"
-   * "qcom,qca6390-bt"
-
-Optional properties for compatible string qcom,qca6174-bt:
-
- - enable-gpios: gpio specifier used to enable chip
- - clocks: clock provided to the controller (SUSCLK_32KHZ)
- - firmware-name: specify the name of nvm firmware to load
-
-Optional properties for compatible string qcom,qca9377-bt:
-
- - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml
-
-Required properties for compatible string qcom,wcn399x-bt:
-
- - vddio-supply: VDD_IO supply regulator handle.
- - vddxo-supply: VDD_XO supply regulator handle.
- - vddrf-supply: VDD_RF supply regulator handle.
- - vddch0-supply: VDD_CH0 supply regulator handle.
-
-Optional properties for compatible string qcom,wcn399x-bt:
-
- - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml
- - firmware-name: specify the name of nvm firmware to load
- - clocks: clock provided to the controller
-
-Examples:
-
-serial@7570000 {
-	label = "BT-UART";
-	status = "okay";
-
-	bluetooth {
-		compatible = "qcom,qca6174-bt";
-
-		enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
-		clocks = <&divclk4>;
-		firmware-name = "nvm_00440302.bin";
-	};
-};
-
-serial@898000 {
-	bluetooth {
-		compatible = "qcom,wcn3990-bt";
-
-		vddio-supply = <&vreg_s4a_1p8>;
-		vddxo-supply = <&vreg_l7a_1p8>;
-		vddrf-supply = <&vreg_l17a_1p3>;
-		vddch0-supply = <&vreg_l25a_3p3>;
-		max-speed = <3200000>;
-		firmware-name = "crnv21.bin";
-		clocks = <&rpmhcc RPMH_RF_CLK2>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml
new file mode 100644
index 0000000..772689b
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml
@@ -0,0 +1,112 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/qualcomm-bluetooth.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Bluetooth Chips
+
+maintainers:
+  - Balakrishna Godavarthi <bgodavar@codeaurora.org>
+  - Rocky Liao <rjliao@codeaurora.org>
+
+description:
+  This binding describes Qualcomm UART-attached bluetooth chips.
+
+properties:
+  compatible:
+    enum:
+      - qcom,qca6174-bt
+      - qcom,qca9377-bt
+      - qcom,wcn3990-bt
+      - qcom,wcn3991-bt
+      - qcom,wcn3998-bt
+      - qcom,qca6390-bt
+
+  enable-gpios:
+    maxItems: 1
+    description: gpio specifier used to enable chip
+
+  clocks:
+    maxItems: 1
+    description: clock provided to the controller (SUSCLK_32KHZ)
+
+  vddio-supply:
+    description: VDD_IO supply regulator handle
+
+  vddxo-supply:
+    description: VDD_XO supply regulator handle
+
+  vddrf-supply:
+    description: VDD_RF supply regulator handle
+
+  vddch0-supply:
+    description: VDD_CH0 supply regulator handle
+
+  max-speed:
+    description: see Documentation/devicetree/bindings/serial/serial.yaml
+
+  firmware-name:
+    description: specify the name of nvm firmware to load
+
+  local-bd-address:
+    description: see Documentation/devicetree/bindings/net/bluetooth.txt
+
+
+required:
+  - compatible
+
+additionalProperties: false
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,qca6174-bt
+    then:
+      required:
+        - enable-gpios
+        - clocks
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,wcn3990-bt
+              - qcom,wcn3991-bt
+              - qcom,wcn3998-bt
+    then:
+      required:
+        - vddio-supply
+        - vddxo-supply
+        - vddrf-supply
+        - vddch0-supply
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    serial {
+
+        bluetooth {
+            compatible = "qcom,qca6174-bt";
+            enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
+            clocks = <&divclk4>;
+            firmware-name = "nvm_00440302.bin";
+        };
+    };
+  - |
+    serial {
+
+        bluetooth {
+            compatible = "qcom,wcn3990-bt";
+            vddio-supply = <&vreg_s4a_1p8>;
+            vddxo-supply = <&vreg_l7a_1p8>;
+            vddrf-supply = <&vreg_l17a_1p3>;
+            vddch0-supply = <&vreg_l25a_3p3>;
+            max-speed = <3200000>;
+            firmware-name = "crnv21.bin";
+        };
+    };
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

Re: [PATCH v4 4/5] dt-bindings: net: bluetooth: Convert Qualcomm BT binding to DT schema

[Rob Herring]

On Tue, 18 May 2021 22:04:45 +0530, Venkata Lakshmi Narayana Gubba wrote:
> Converted Qualcomm Bluetooth binidings to DT schema.
> 
> Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
> ---
>  .../devicetree/bindings/net/qualcomm-bluetooth.txt |  69 -------------
>  .../bindings/net/qualcomm-bluetooth.yaml           | 112 +++++++++++++++++++++
>  2 files changed, 112 insertions(+), 69 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
>  create mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH v4 5/5] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750

[Venkata Lakshmi Narayana Gubba]

This patch enables regulators and gpios for the Qualcomm Bluetooth wcn6750
controller.

Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
---
 .../bindings/net/qualcomm-bluetooth.yaml           | 71 ++++++++++++++++++++++
 1 file changed, 71 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml
index 772689b..f93c6e7 100644
--- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml
+++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml
@@ -22,11 +22,17 @@ properties:
       - qcom,wcn3991-bt
       - qcom,wcn3998-bt
       - qcom,qca6390-bt
+      - qcom,wcn6750-bt
 
   enable-gpios:
     maxItems: 1
     description: gpio specifier used to enable chip
 
+  swctrl-gpios:
+    maxItems: 1
+    description: gpio specifier is used to find status
+                 of clock supply to SoC
+
   clocks:
     maxItems: 1
     description: clock provided to the controller (SUSCLK_32KHZ)
@@ -43,6 +49,30 @@ properties:
   vddch0-supply:
     description: VDD_CH0 supply regulator handle
 
+  vddaon-supply:
+    description: VDD_AON supply regulator handle
+
+  vddbtcxmx-supply:
+    description: VDD_BT_CXMX supply regulator handle
+
+  vddrfacmn-supply:
+    description: VDD_RFA_CMN supply regulator handle
+
+  vddrfa0p8-supply:
+    description: VDD_RFA_0P8 suppply regulator handle
+
+  vddrfa1p7-supply:
+    description: VDD_RFA_1P7 supply regulator handle
+
+  vddrfa1p2-supply:
+    description: VDD_RFA_1P2 supply regulator handle
+
+  vddrfa2p2-supply:
+    description: VDD_RFA_2P2 supply regulator handle
+
+  vddasd-supply:
+    description: VDD_ASD supply regulator handle
+
   max-speed:
     description: see Documentation/devicetree/bindings/serial/serial.yaml
 
@@ -85,6 +115,25 @@ allOf:
         - vddrf-supply
         - vddch0-supply
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,wcn6750-bt
+    then:
+      required:
+        - enable-gpios
+        - swctrl-gpios
+        - vddio-supply
+        - vddaon-supply
+        - vddbtcxmx-supply
+        - vddrfacmn-supply
+        - vddrfa0p8-supply
+        - vddrfa1p7-supply
+        - vddrfa1p2-supply
+        - vddasd-supply
+
 examples:
   - |
     #include <dt-bindings/gpio/gpio.h>
@@ -110,3 +159,25 @@ examples:
             firmware-name = "crnv21.bin";
         };
     };
+  - |
+    serial {
+
+        bluetooth {
+            compatible = "qcom,wcn6750-bt";
+            pinctrl-names = "default";
+            pinctrl-0 = <&bt_en_default>;
+            enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+            swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+            vddio-supply = <&vreg_l19b_1p8>;
+            vddaon-supply = <&vreg_s7b_0p9>;
+            vddbtcxmx-supply = <&vreg_s7b_0p9>;
+            vddrfacmn-supply = <&vreg_s7b_0p9>;
+            vddrfa0p8-supply = <&vreg_s7b_0p9>;
+            vddrfa1p7-supply = <&vreg_s1b_1p8>;
+            vddrfa1p2-supply = <&vreg_s8b_1p2>;
+            vddrfa2p2-supply = <&vreg_s1c_2p2>;
+            vddasd-supply = <&vreg_l11c_2p8>;
+            max-speed = <3200000>;
+            firmware-name = "msnv11.bin";
+        };
+    };
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

Re: [PATCH v4 5/5] dt-bindings: net: bluetooth: Add device tree bindings for QTI chip wcn6750

[Rob Herring]

On Tue, 18 May 2021 22:04:46 +0530, Venkata Lakshmi Narayana Gubba wrote:
> This patch enables regulators and gpios for the Qualcomm Bluetooth wcn6750
> controller.
> 
> Signed-off-by: Venkata Lakshmi Narayana Gubba <gubbaven@codeaurora.org>
> ---
>  .../bindings/net/qualcomm-bluetooth.yaml           | 71 ++++++++++++++++++++++
>  1 file changed, 71 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v4 0/5] Enable Bluetooth functionality for WCN6750

[Marcel Holtmann]

Hi Venkata,

> These patches enables Bluetooth functionalties for new Qualcomm
> Bluetooth SoC wcn6750.
> 
> Venkata Lakshmi Narayana Gubba (5):
>  Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6750
>  Bluetooth: btqca: Add support for firmware image with mbn type for
>    WCN6750
>  Bluetooth: btqca: Moved extracting rom version info to common place
>  dt-bindings: net: bluetooth: Convert Qualcomm BT binding to DT schema
>  dt-bindings: net: bluetooth: Add device tree bindings for QTI chip
>    wcn6750
> 
> .../devicetree/bindings/net/qualcomm-bluetooth.txt |  69 --------
> .../bindings/net/qualcomm-bluetooth.yaml           | 183 +++++++++++++++++++++
> drivers/bluetooth/btqca.c                          |  90 +++++++---
> drivers/bluetooth/btqca.h                          |  14 +-
> drivers/bluetooth/hci_qca.c                        | 114 ++++++++++---
> 5 files changed, 354 insertions(+), 116 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
> create mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.yaml

all 5 patches have been applied to bluetooth-next tree.

Regards

Marcel